Philips 201E1 User Manual

e-M anual  
Philips LCD Monitor Electronic User’s Manual  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/INDEX.HTM 2009-5-2114:40:04  
SafetyandTroubleshootingInformation  
extreme cold.  
In order to maintain the best performance of your monitor and use it for a longer lifetime,  
please use the monitor in a location that falls within the following temperature and  
humidity ranges.  
Temperature: 0-40°C 32-95°F  
Humidity: 20-80% RH  
IMPORTANT: Always activate a moving screen saver program when you leave your  
monitor unattended. Always activate a periodic screen refresh application if your LCD  
monitor will display unchanging static content. Uninterrupted display of still or static  
images over an extended period may cause “burn in”, also known as “after-imaging” or  
“ghost imaging”, on your screen. "Burn-in", "after-imaging", or "ghost imaging" is a well-  
known phenomenon in LCD panel technology. In most cases, the “burned in” or “after-  
imaging” or “ghost imaging” will disappear gradually over a period of time after the power  
has been switched off.  
WARNING: Severe” burn-in” or “after-image” or “ghost image” symptoms will not  
disappear and cannot be repaired. The damage mentioned above is not covered under  
your warranty.  
Service:  
The casing cover should be opened only by qualified service personnel.  
If there is any need for any document for repair or integration, please contact with your  
local service center. (please refer to the chapter of "Consumer Information Center")  
For transportation information, please refer to "Physical Specifications".  
Do not leave your monitor in a car/trunk under direct sun light.  
Consult a service technician if the monitor does not operate normally, or you are  
not sure what procedure to take when the operating instructions given in this  
manual have been followed.  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/safety/safety.htm22)2009-5-2114:40:53  
FAQs(FrequentlyAskedQuestions)  
FAQs (Frequently Asked Questions)  
General FAQs  
Q1: When I install my monitor what should I do if the screen shows 'Cannot display this  
video mode'?  
A: Recommended resolution for Philips 20": 1600x900 @60Hz.  
1. Unplug all cables, then connect your PC to the monitor that you used  
previously.  
2. In the Windows Start Menu, select Settings/Control Panel. In the Control Panel  
Window, select the Display icon. Inside the Display Control Panel, select the  
'Settings' tab. Under the setting tab, in box labeled 'desktop area', move the  
slidebar to 1600x900 pixels (20").  
3. Open 'Advanced Properties' and set the Refresh Rate to 60Hz, then click OK.  
4. Restart your computer and repeat step 2 and 3 to verify that your PC is set at  
1600x900@60Hz (20").  
5. Shut down your computer, disconnect your old monitor and reconnect your  
Philips LCD monitor.  
6. Turn on your monitor and then turn on your PC.  
Q2: What does the recommended refresh rate for LCD monitor?  
A:Recommended refresh rate in LCD monitors is 60Hz, In case of any disturbance  
on screen, you can set it up to 75Hz to see if that removes the disturbance.  
Q3: What are the .inf and .icm files on the CD-ROM? How do I install the drivers (.inf and .  
icm)?  
A: These are the driver files for your monitor. Follow the instructions in your user  
manual to install the drivers. Your computer may ask you for monitor drivers (.inf and .  
icm files) or a driver disk when you first install your monitor. Follow the instructions to  
insert the ( companion CD-ROM) included in this package. Monitor drivers (.inf and .  
icm files) will be installed automatically.  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/safety/saf_faq.htm15)2009-5-2114:41:00  
     
FAQs(FrequentlyAskedQuestions)  
Q4: How do I adjust the resolution?  
A: Your video card/graphic driver and monitor together determine the available  
resolutions. You can select the desired resolution under Windows® Control Panel  
with the "Display properties".  
Q5: What if I get lost when I am making monitor adjustments?  
A: Simply press the OK button, then select 'Reset' to recall all of the original factory  
settings.  
Q6: Will the LCD screen be resistant to scratches?  
A: In general it is recommended that the panel surface is not subjected to excessive  
shocks and is protected from sharp or blunt objects. When handling the monitor,  
make sure that there is no pressure or force applied to the panel surface side. This  
may affect your warranty conditions.  
Q7: How should I clean the LCD surface?  
A: For normal cleaning, use a clean, soft cloth. For extensive cleaning, please use  
isopropyl alcohol. Do not use other solvents such as ethyl alcohol, ethanol, acetone,  
hexane, etc.  
Q8:Can I change the color setting of my monitor?  
A:Yes, you can change your color setting through OSD control as the following  
procedures,  
1. Press "OK" to show the OSD (On Screen Display) menu  
2. Press "Down Arrow" to select the option "Color" then press "OK" to enter color  
setting, there are three settings as below.  
a. Color Temperature; The 2 settings are 6500K,  
9300K .  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/safety/saf_faq.htm25)2009-5-2114:41:00  
FAQs(FrequentlyAskedQuestions)  
b. sRGB; this is a standard setting for ensuring correct exchange of colors  
between different device (e.g. digital cameras, monitors, printers, scanners,  
etc)  
c. User Define; the user can choose his/her preference color setting by  
adjusting red, green blue color.  
*A measurement of the color of light radiated by an object while it is being heated.  
This measurement is expressed in terms of absolute scale, (degrees Kelvin). Lower  
Kevin temperatures such as 2004K are red; higher temperatures such as 9300K are  
blue. Neutral temperature is white, at 6504K.  
Q9: Can the Philips LCD Monitor be mounted on the wall?  
A: Yes. Philips LCD monitors have this optional feature. For standard VESA mount  
holes on the rear cover allows the user to mount the Philips monitor on most of the  
VESA standard arms or accessories. We recommend to contact your Philips sales  
representative for more information.  
Compatibility with other Peripherals  
Q10: Can I connect my LCD monitor to any PC, workstation or Mac?  
A: Yes. All Philips LCD monitors are fully compatible with standard PCs, Macs and  
workstations. You may need a cable adapter to connect the monitor to your Mac  
system. Please contact your Philips sales representative for more information.  
Q11: Are Philips LCD monitors Plug-and-Play?  
A: Yes, the monitors are Plug-and-Play compatible with Windows® 95, 98, 2000, XP,  
Vista and Linux.  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/safety/saf_faq.htm35)2009-5-2114:41:00  
 
FAQs(FrequentlyAskedQuestions)  
LCD Panel Technology  
Q12: What kind of wide-angle technology is available?  
A: Currently, the IPS type panels offer the best Contrast Ratio, compared to MVA, or  
PVA technologies. TN panels have improved over the years, but still cannot match  
the Contrast Ratio offered by IPS panel.  
Ergonomics, Ecology and Safety Standards  
Q13: What is Image Sticking, or Image Burn-in, or After Image, or Ghost Image in LCD  
panels?  
A: Uninterrupted display of still or static images over an extended period may cause  
"burn in", also known as "after-imaging" or "ghost imaging", on your screen. "Burn-in",  
"after-imaging", or "ghost imaging" is a well-known phenomenon in LCD panel  
technology. In most cases, the "burned in" or "atter-imaging" or "ghost imaging" will  
disappear gradually over a period of time after the power has been switched off.  
Always activate a moving screen saver program when you leave your monitor  
unattended.  
Always activate a periodic screen refresh application if your LCD monitor will display  
unchanging static content.  
WARNING: Severe"burn-in" or "after-image" or "ghost image" symptoms will not  
disappear and cannot be repaired. The damage mentioned above is not covered  
under your warranty.  
Q14: Why is my Display not showing sharp text, and is displaying jagged characters?  
A: Your LCD monitor works best at its native resolution of 1600x900@60Hz. For best  
display please use this resolution.  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/safety/saf_faq.htm45)2009-5-2114:41:00  
   
FAQs(FrequentlyAskedQuestions)  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/safety/saf_faq.htm55)2009-5-2114:41:00  
Troubleshooting  
Troubleshooting  
This page deals with problems that can be corrected by a user. If the problem still persists after you have tried these  
solutions, contact Philips customer service representative.  
Common Problems  
Having this problem  
Check these items  
Make sure the power cord is plugged into the power outlet  
and into the back of the monitor.  
First, ensure that the power button on the front of the monitor  
is in the OFF position, then press it to the ON position.  
No Picture  
(Power LED not lit)  
Make sure the computer is turned on.  
Make sure the signal cable is properly connected to your  
computer.  
No Picture  
make sure the monitor cable has no bent pins on the connect  
side. If yes, repair or replace the cable.  
The Energy Saving feature may be activated  
(Power LED is orange)  
Screen says  
Make sure the monitor cable is properly connected to your  
computer. (Also refer to the Quick Set-Up Guide).  
Check to see if the monitor cable has bent pins.  
Make sure the computer is turned on.  
The auto function is applicable only in VGA-Analog mode. If  
the result is not satisfactory, you can do manual adjustments  
via the OSD menu. Note that the Auto Function is not  
applicable in DVI-Digital mode as it is not necessary.  
AUTO button doesn't function in VGA  
mode  
Imaging Problems  
Press the Auto button.  
Adjust the image position using the Phase/Clock of Setup in  
Image is not centered  
OSD Main Controls.  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/safety/saf_troub.htm13)2009-5-2114:41:12  
       
Troubleshooting  
Check that the signal cable is properly securely connected to  
the graphics board or PC.  
Image vibrates on the screen  
Vertical flicker appears  
Press the Auto button.  
Eliminate the vertical bars using the Phase/Clock of Setup in  
OSD Main Controls.  
Horizontal flicker appears  
Press the Auto button.  
Eliminate the vertical bars using the Phase/Clock of Setup in  
OSD Main Controls.  
Adjust the contrast and brightness on On-Screen Display.  
image appears blurred, indistinct or too  
dark  
Uninterrupted display of still or static images over an  
extended period may cause " burn in", also known as "after-  
imaging " or "ghost imaging", on your screen. "Burn-in", "after-  
imaging", or "ghost imaging" is a well-known phenomenon in  
LCD panel technology. In most cases, the "burned in" or  
"after-imaging" or "ghost imaging" will disappear gradually  
over a period of time after the power has been switched off.  
Always activate a moving screen saver program when you  
leave your monitor unattended.  
An "after-image", "burn-in" or "ghost  
image" remains after the power has  
been turned off.  
Always activate a periodic screen refresh application if your  
LCD monitor will display unchanging static content.  
Set the PC’s display resolution to the same mode as  
monitor’s recommended screen native resolution.  
Image appears distorted. Text is fuzzy  
or blurred.  
The remaining dots are normal characteristic of the liquid  
crystal used in today’s technology, Pls refer the pixel policy  
Green, red, blue, dark, and white dots  
appears on the screen  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/safety/saf_troub.htm23)2009-5-2114:41:12  
Troubleshooting  
You can adjust “power on” light using the power LED of Setup  
in OSD main Controls.  
The "power on" light is too strong to  
disturb me.  
For further assistance, refer to the Consumer Information Centers list and contact Philips customer service  
representative.  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/safety/saf_troub.htm33)2009-5-2114:41:12  
RegulatoryInformation  
Regulatory Information  
Product name:  
Model No:  
201E1  
MWE1201T  
TCO'03 Information  
Congratulations!  
The display you have just purchased carries the TCO'03 Displays label. This means  
that your display is designed, manufactured and tested according to some of the  
strictest quality and environmental requirements in the world. This makes for a high  
performance product, designed with the user in focus that also minimizes the impact  
on our natural environment.  
*available for selective models  
Some of the features of the TCO'03 Display requirements.  
Ergonomics  
Good visual ergonomics and image quality in order to improve the working environment for the user and  
to reduce sight and strain problems. Important parameters are luminance, contrast, resoluction,  
reflectance, colour rendition and image stability.  
Energy  
Energy-saving mode after a certain time-beneficial both for the user and the environment  
Electrical safety  
Emissions  
Electromagnetic fields  
Noise emissions  
Ecology  
The product must be prepared for recycling and the manufacturer must have a certified environmental  
management system such as EMAS or ISO 14 000  
Restrictions on  
chlorinated and brominated flame retardants and polymers  
heavy metals such as cadmium, mercury and lead.  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/safety/regs/regulat.htm1/11)2009-5-2114:41:23  
     
RegulatoryInformation  
TCO'06 Information  
Congratulations!  
The product you have just purchased carries the TCO’06 Media Displays label. This  
means that your display is designed and manufactured according to some of the  
strictest performance and environmental criteria in the world. The manufacturer of  
this display has selected it to be certified to TCO’06 Media Displays as a sign of  
usability, high performance and reduced impact on the natural environment.  
*available for selective models  
Products certified to TCO´06 Media Displays are specifically designed for high quality reproduction of moving  
images. Features such as luminance, color rendition and response time are important when watching TV or  
working with media, graphics, web design and other applications that demand outstanding moving images. *  
Other features of TCO’06 Media Displays:  
Ergonomics  
Good visual ergonomics and image quality in order to reduce vision and strain problems. Criteria for  
luminance, contrast, resolution, reflectance, color rendition and response time.  
Energy  
Energy saving mode – beneficial both for the user and the environment  
Electrical safety  
Emissions  
Low electromagnetic fields surrounding the display  
Ecology  
Product is designed for recycling. Manufacturer must have a certified environmental management system  
such as EMAS or ISO 14 001  
Restrictions on  
Chlorinated and brominated flame retardants and polymers.  
Hazardous heavy metals such as cadmium, mercury, hexavalent chromium and lead.  
The requirements included in this label have been developed by TCO Development in co-operation with  
scientists, experts, users as well as manufacturers all over the world. Since the end of the 1980s TCO has been  
involved in influencing the development of IT equipment in a more user-friendly direction. Our labelling system  
started with displays in 1992 and is now requested by users and IT-manufacturers all over the world.  
For more information, please visit  
Recycling Information for Customers  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/safety/regs/regulat.htm2/11)2009-5-2114:41:23  
   
RegulatoryInformation  
Philips establishes technically and economically viable objectives to optimize the environmental performance of  
the organization's product, service and activities.  
From the planning, design and production stages, Philips emphasizes the important of making products that can  
easily be recycled. At Philips, end-of-life management primarily entails participation in national take-back  
initiatives and recycling programs whenever possible, preferably in cooperation with competitors.  
There is currently a system of recycling up and running in the European countries, such as The Netherlands,  
Belgium, Norway, Sweden and Denmark.  
In U.S.A., Philips Consumer Electronics North America has contributed funds for the Electronic Industries  
Alliance (EIA) Electronics Recycling Project and state recycling initiatives for end-of-life electronics products from  
household sources. In addition, the Northeast Recycling Council (NERC) - a multi-state non-profit organization  
focused on promoting recycling market development - plans to implement a recycling program.  
In Asia Pacific, Taiwan, the products can be taken back by Environment Protection Administration (EPA) to  
follow the IT product recycling management process, detail can be found in web site www.epa.gov.tw  
The monitor contains parts that could cause damage to the nature environment. Therefore, it is vital that the monitor is  
recycled at the end of its life cycle.  
in each country.  
Waste Electrical and Electronic Equipment-WEEE  
Attention users in European Union private households  
This marking on the product or on its packaging illustrates that, under European Directive 2002/96/  
EC governing used electrical and electronic appliances, this product may not be disposed of with normal  
household waste. You are responsible for disposal of this equipment through a designated waste electrical and  
electronic equipment collection. To determine the locations for dropping off such waste electrical and electronic,  
contact your local government office, the waste disposal organization that serves your household or the store at  
which you purchased the product.  
Attention users in United States:  
Like all LCD products, this set contains a lamp with Mercury. Please dispose of according to all Local, State and  
Federal laws. For the disposal or recyciing information, contact www.mygreenelectronics.com or www.eiae.org.  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/safety/regs/regulat.htm3/11)2009-5-2114:41:23  
 
RegulatoryInformation  
EPEAT  
“The EPEAT (Electronic Product Environmental Assessment Tool) program evaluates computer desktops,  
laptops, and monitors based on 51 environmental criteria developed through an extensive stakeholder  
consensus process supported by US EPA.  
EPEAT system helps purchasers in the public and private sectors evaluate, compare and select desktop  
computers, notebooks and monitors based on their environmental attributes. EPEAT also provides a clear and  
consistent set of performance criteria for the design of products, and provides an opportunity for manufacturers  
to secure market recognition for efforts to reduce the environmental impact of its products.”  
Benefits of EPEAT  
Reduce use of primary materials  
Reduce use of toxic materials  
Avoid the disposal of hazardous waste  
EPEAT’S requirement that all registered products meet ENERGY STAR’s energy efficiency specifications,  
means that these products will consume less energy throughout their life.  
ROHS is a European Directive aiming to control the use of certain hazardous substances in the production of  
new electrical and electronic equipment. Philips has completely eliminated four of six RoHS-banned substances  
form its products by 1998-eight full years before compliance was required and has lowered usage of the  
remaining substances significantly below the mandated levels.  
CE Declaration of Conformity  
Philips Consumer Electronics declare under our responsibility that the product is in conformity with the following  
standards  
- EN60950-1:2001 (Safety requirement of Information Technology Equipment)  
- EN55022:2006 (Radio Disturbance requirement of Information Technology Equipment)  
- EN55024:1998+A1:2001+A2:2003 (Immunity requirement of Information Technology Equipment)  
- EN61000-3-2:2000 or EN61000-3-2:2006(Limits for Harmonic Current Emission)  
- EN61000-3-3:1995+A1:2001+A2:2005 (Limitation of Voltage Fluctuation and Flicker)  
following provisions of directives applicable  
- 73/23/EEC (Low Voltage Directive)  
- 2004/108/EC(EMC Directive)  
- 2006/95/EC (Low Voltage Directive)  
and is produced by a manufacturing organization on ISO9000 level.  
The product also comply with the following standards  
- ISO13406-2 (Ergonomic requirement for Flat Panel Display)  
- GS EK1-2000 (GS specification)  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/safety/regs/regulat.htm4/11)2009-5-2114:41:23  
 
RegulatoryInformation  
- prEN50279:1998 (Low Frequency Electric and Magnetic fields for Visual Display)  
- MPR-II (MPR:1990:8/1990:10 Low Frequency Electric and Magnetic fields)  
- TCO'03 (Requirement for Environment Labelling of Ergonomics, Energy, Ecology and Emission, TCO: Swedish  
Confederation of Professional Employees) for TCO versions  
Energy Star Declaration  
This monitor is equipped with a function for saving energy which supports the VESA DPM  
standard. This means that the monitor must be connected to a computer which supports VESA  
DPM. Time settings are adjusted from the system unit by software.  
VESA State  
ON (Active)  
LED Indicator  
Green  
Power Consumption  
Normal operation  
< 24.5W (typ.)  
Power Saving  
Alternative 2  
One step  
Sleep  
Orange  
< 0.8 W (typ.)  
< 0.5 W (typ.)  
Switch Off  
Off  
As an ENERGY STAR® Partner, PHILIPS has determined that this product meets  
®
the ENERGY STAR guidelines for energy efficiency.  
We recommend you switch off the monitor when it is not in use for a long time.  
Federal Communications Commission (FCC) Notice (U.S. Only)  
This equipment has been tested and found to comply with the limits for a Class B digital  
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide  
reasonable protection against harmful interference in a residential installation. This  
equipment generates, uses and can radiate radio frequency energy and, if not installed and  
used in accordance with the instructions, may cause harmful interference to radio  
communications. However, there is no guarantee that interference will not occur in a  
particular installation. If this equipment does cause harmful interference to radio or  
television reception, which can be determined by turning the equipment off and on, the user  
is encouraged to try to correct the interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/safety/regs/regulat.htm5/11)2009-5-2114:41:23  
   
RegulatoryInformation  
Consult the dealer or an experienced radio/TV technician for help.  
Changes or modifications not expressly approved by the party responsible for compliance  
could void the user's authority to operate the equipment.  
Use only RF shielded cable that was supplied with the monitor when connecting this monitor to a computer  
device.  
To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or excessive  
moisture.  
THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE-  
CAUSING EQUIPMENT REGULATIONS.  
FCC Declaration of Conformity  
Trade Name: Philips  
Philips Consumer Electronics North America  
P.O. Box 671539  
Marietta , GA 30006-0026  
Responsible Party:  
1-888-PHILIPS (744-5477)  
Declaration of Conformity for Products Marked with FCC Logo,  
United States Only  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause  
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired  
operation.  
Commission Federale de la Communication (FCC Declaration)  
Cet équipement a été testé et déclaré conforme auxlimites des appareils numériques de  
class B,aux termes de l'article 15 Des règles de la FCC. Ces limites sont conçues de façon  
à fourir une protection raisonnable contre les interférences nuisibles dans le cadre d'une  
installation résidentielle. CET appareil produit, utilise et peut émettre des hyperfréquences  
qui, si l'appareil n'est pas installé et utilisé selon les consignes données, peuvent causer  
des interférences nuisibles aux communications radio. Cependant, rien ne peut garantir  
l'absence d'interférences dans le cadre d'une installation particulière. Si cet appareil est la  
cause d'interférences nuisibles pour la réception des signaux de radio ou de télévision, ce  
qui peut être décelé en fermant l'équipement, puis en le remettant en fonction, l'utilisateur  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/safety/regs/regulat.htm6/11)2009-5-2114:41:23  
 
RegulatoryInformation  
pourrait essayer de corriger la situation en prenant les mesures suivantes:  
Réorienter ou déplacer l'antenne de réception.  
Augmenter la distance entre l'équipement et le récepteur.  
Brancher l'équipement sur un autre circuit que celui utilisé par le récepteur.  
Demander l'aide du marchand ou d'un technicien chevronné en radio/télévision.  
Toutes modifications n'ayant pas reçu l'approbation des services compétents en matière de  
conformité est susceptible d'interdire à l'utilisateur l'usage du présent équipement.  
N'utiliser que des câbles RF armés pour les connections avec des ordinateurs ou périphériques.  
CET APPAREIL NUMERIQUE DE LA CLASSE B RESPECTE TOUTES LES EXIGENCES DU REGLEMENT  
SUR LE MATERIEL BROUILLEUR DU CANADA.  
EN 55022 Compliance (Czech Republic Only)  
Polish Center for Testing and Certification Notice  
The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All  
equipment that works together (computer, monitor, printer, and so on) should have the same power supply  
source.  
The phasing conductor of the room's electrical installation should have a reserve short-circuit protection device in  
the form of a fuse with a nominal value no larger than 16 amperes (A).  
To completely switch off the equipment, the power supply cable must be removed from the power supply socket,  
which should be located near the equipment and easily accessible.  
A protection mark "B" confirms that the equipment is in compliance with the protection usage requirements of  
standards PN-93/T-42107 and PN-89/E-06251.  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/safety/regs/regulat.htm7/11)2009-5-2114:41:23  
   
RegulatoryInformation  
North Europe (Nordic Countries) Information  
Placering/Ventilation  
VARNING:  
FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR  
DU STÄLLER DIN UTRUSTNING PÅPLATS.  
Placering/Ventilation  
ADVARSEL:  
SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT  
ER NEMT TILGÆNGELIGE.  
Paikka/Ilmankierto  
VAROITUS:  
SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI  
IRROTTAA PISTORASIASTA.  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/safety/regs/regulat.htm8/11)2009-5-2114:41:23  
 
RegulatoryInformation  
Plassering/Ventilasjon  
ADVARSEL:  
NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE FOR  
STØMTILFØRSEL ER LETTE Å NÅ.  
BSMI Notice (Taiwan Only)  
Ergonomie Hinweis (nur Deutschland)  
Der von uns gelieferte Farbmonitor entspricht den in der "Verordnung über den Schutz vor Schäden durch  
Röntgenstrahlen" festgelegten Vorschriften.  
Auf der Rückwand des Gerätes befindet sich ein Aufkleber, der auf die Unbedenklichkeit der Inbetriebnahme  
hinweist, da die Vorschriften über die Bauart von Störstrahlern nach Anlage III ¤ 5 Abs. 4 der  
Röntgenverordnung erfüllt sind.  
Damit Ihr Monitor immer den in der Zulassung geforderten Werten entspricht, ist darauf zu achten, daß  
1. Reparaturen nur durch Fachpersonal durchgeführt werden.  
2. nur original-Ersatzteile verwendet werden.  
3. bei Ersatz der Bildröhre nur eine bauartgleiche eingebaut wird.  
Aus ergonomischen Gründen wird empfohlen, die Grundfarben Blau und Rot nicht auf dunklem  
Untergrund zu verwenden (schlechte Lesbarkeit und erhöhte Augenbelastung bei zu geringem  
Zeichenkontrast wären die Folge).  
Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 beträgt 70dB (A) oder weniger.  
ACHTUNG: BEIM AUFSTELLEN DIESES GERÄTES DARAUF ACHTEN, DAß  
NETZSTECKER UND NETZKABELANSCHLUß LEICHT ZUGÄNGLICH SIND.  
End-of-Life Disposal  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/safety/regs/regulat.htm9/11)2009-5-2114:41:23  
     
RegulatoryInformation  
Your new monitor contains materials that can be recycled and reused. Specialized companies can recycle your  
product to increase the amount of reusable materials and to minimize the amount to be disposed of.  
Please find out about the local regulations on how to dispose of your old monitor from your sales representative.  
(For customers in Canada and U.S.A.)  
This product may contain lead and/or mercury. Dispose of in accordance to local-state and federal regulations.  
For additional information on recycling contact www.eia.org (Consumer Education Initiative)  
China RoHS  
The People's Republic of China released a regulation called "Management Methods for Controlling Pollution by  
Electronic Information Products" or commonly referred to as China RoHS. All products including CRT and LCD  
monitor which are produced and sold for China market have to meet China RoHS request.  
环保使用期限  
此标识指期限(),子信息产品中含有的有毒有害物质或元素在正常使用的条件下不会发生外泄或突  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/safety/regs/regulat.htm10/11)2009-5-2114:41:23  
 
RegulatoryInformation  
变,电子信息产品用户使用该电子信息产品不会对环境造成严重污染或对其人身财产造成严重损害的期  
限.  
Lead-free Product  
Philips eliminated toxic substances like lead from its displays. Lead-free display helps protect your  
health and promotes environmentally sound recovery and disposal of waste from electrical and  
electronic equipment.Philips complies with the European Community stringent RoHS Directive  
mandating restrictions on hazardous substances in electrical and electronic equipment. With  
Philips, you can be confident that your display device does not harm the environment.  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/safety/regs/regulat.htm11/11)2009-5-2114:41:23  
 
AboutThisM anual  
About This Manual  
About This Guide  
This electronic user's guide is intended for anyone who uses the Philips LCD Monitor. It  
describes the LCD monitor's features, setup, operation and other important information. Its  
contents are identical to the information in our printed version.  
It includes the following sections:  
Safety and Troubleshooting Information provides tips and solutions for common problems  
as well as other related information you may need.  
About This Electronic User's Manual gives an overview of information included, along with  
notation icon descriptions and other documentation for your reference.  
Product Information gives an overview of the monitor's features as well as the technical  
specifications for this monitor.  
Installing Your Monitor describes the initial setup process and gives an overview of how to  
use the monitor.  
On-Screen Display provides information on adjusting the settings on your monitor.  
Customer Care and Warranty contains a list of worldwide Philips Consumer Information  
Centers along with help desk phone numbers and information on the warranty applicable  
to your product.  
Glossary defines technical terms.  
Download and Print Option transfers this entire manual to your hard drive for easy  
reference.  
Notational Descriptions  
The following subsections describe notational conventions used in this document.  
Notes, Cautions and Warnings  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/about/about.htm12)2009-5-2114:41:34  
       
AboutThisM anual  
Throughout this guide, blocks of text may be accompanied by an icon and printed in bold or italic  
type. These blocks contain notes, cautions or warnings. They are used as follows:  
NOTE: This icon indicates important information and tips that help you make  
better use of your computer system.  
CAUTION: This icon indicates information that tells you how to avoid either  
potential damage to hardware or loss of data.  
WARNING: This icon indicates the potential for bodily harm and tells you how  
to avoid the problem.  
Some warnings may appear in alternate formats and may not be accompanied by an icon. In  
such cases, the specific presentation of the warning is mandated by the relevant regulatory  
authority.  
©2009 Koninklijke Philips Electronics NV  
All rights reserved. Reproduction, copying, use, modification, hiring, renting, public performance, transmission and/or  
broadcasting in whole or in part is prohibited without written consent of Philips Electronics NV  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/about/about.htm22)2009-5-2114:41:34  
ProductInformation  
Product Information  
Your LCD monitor  
Congratulations on your purchase and welcome to Philips. To fully benefit from the support that Philips offers, register  
SmartContrast  
What is it?  
Unique technology that dynamically analyzes displayed content and automatically optimizes a LCD monitor's contrast  
ratio for maximum visual clarity and viewing enjoyment, stepping up backlighting for clearer, crisper and brighter  
images or dimming backlighting for clear display of images on dark backgrounds.  
Why do I need it?  
You want the very best visual clarity and viewing comfort for every type of content. SmartContrast dynamically controls  
contrast and adjusts backlighting for clear, crisp, bright gaming and video images or displays clear, readable text for  
office work. By reducing your monitor's power consumption, you save on energy costs and extend the lifetime of your  
monitor.  
How does it work?  
When you active SmartContrast which will analysis the content you are displaying in real time to adjust colors and  
control backlight intensity. This function can obviously enhance contrast in dynamic for more entertainment fun when  
viewing videos or playing games.  
Technical Specifications*  
Picture/Display  
• LCD panel type  
• Panel size  
TFT-LCD  
20"  
• Aspect ratio  
• Pixel Pitch  
16:9  
0.2768 x 0.2768 mm  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/product/product.htm16)2009-5-2114:42:04  
         
ProductInformation  
• Brightness  
250 cd/m²  
•SmartContrast  
25000:1  
•Contrast ratio(typ.)  
• Response time (typical)  
• Optimum Resolution  
• Viewing angle  
1000:1  
5 ms  
1600 x 900 @ 60Hz  
160° (H) / 160° (V) @ C/R > 10  
• Display colors  
• Scanning Frequency  
• sRGB  
16.7 M  
30 - 83 kHz (H)/56 -75Hz (V)  
YES  
Connectivity  
• Signal input  
• Input Signal  
Convenience  
DVI-D (digital, HDCP), VGA (Analog)  
Separate Sync, Sync on Green  
• User Convenience  
• OSD Languages  
Auto(Back), 4:3/Wide(Down), Brightness(Up), Menu(OK), Power On/Off  
English, French, German, Italian, Russian, Spanish, Simplified Chinese,  
Portuguese, Turkish  
• Other convenience  
• Plug & Play Compatibility  
Stand  
VESA mount ( 100 x 100mm), Kensington lock  
DDC/CI, sRGB, Windows 98/2000/XP/Vista, Mac OS X  
• Tilt  
-5/+20  
Power  
• On mode (typcial)  
< 24.5 W  
AC Input Voltage at  
100VAC +/-5VAC,  
50Hz +/- 3Hz  
AC Input Voltage at  
115VAC +/-5VAC,  
60Hz +/- 3Hz  
AC Input Voltage at  
230VAC +/-5VAC, 50Hz  
+/ -3Hz  
Energy Consumption  
(EnergyStar 5.0 test method)  
Normal Operation  
20.5W  
0.8 W  
0.5 W  
20.4 W  
0.8 W  
0.5 W  
20.3 W  
0.8 W  
0.5 W  
Sleep  
Off  
AC Input Voltage at  
100VAC +/-5VAC,  
50Hz +/ -3Hz  
AC Input Voltage at  
115VAC +/-5VAC,  
60Hz +/ -3Hz  
AC Input Voltage at  
230VAC +/-5VAC, 50Hz  
+/ -3Hz  
Heat Dissipation*  
Normal Operation  
Sleep  
70.0BTU/hr  
69.6BTU/hr  
69.3BTU/hr  
2.7BTU/hr  
2.7BTU/hr  
2.7BTU/hr  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/product/product.htm26)2009-5-2114:42:04  
ProductInformation  
Off  
1.7BTU/hr  
1.7BTU/hr  
1.7BTU/hr  
• Power LED indicator  
• Power Supply  
Dimension  
On mode: Green, Standby/Sleep mode: orange  
Build-in, 100-240VAC, 50/60Hz  
• Product with stand ( WxHxD)  
478.94 x 353.45 x 189.81mm  
478.94 x 290.6 x 61.43mm  
555 x 354 x 140mm  
• Product without stand  
( WxHxD)  
• Box dimension ( WxHxD)  
Weight  
• Product with stand  
• Product without stand  
• Product with packaging  
Operating Condition  
3.97kg  
3.69kg  
5.85kg  
• Temperature range (operation) 0° C to 40 ° C  
• Temperature range (operation) -20° C to 60° C  
• Relative humidity  
20% to 80%  
Non-operation: + 12,000 ft ( 3,658 m)  
operation: + 40,000 ft ( 12,192 m),  
50000 hrs  
• Altitude  
• MTBF  
Environmental  
• ROHS  
YES  
• EPEAT  
sliver  
• EnergyStar  
• Packaging  
5.0  
100% recyclable  
Compliance and standards  
• Regulatory Approvals  
CE Mark, Energy Star 5.0, FCC Class B, SEMKO  
Cabinet  
• Color  
Black/Black  
Glossy  
• Finish  
* This data is subject to change without notice.  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/product/product.htm36)2009-5-2114:42:04  
ProductInformation  
Resolution & Preset Modes  
A.  
-
Maximum Resolution  
For 201E1  
1600 x 900 at 75 Hz (analog input)  
1600 x 900 at 75 Hz (digital input)  
B. Recommended Resolution  
-
For 201E1  
1600 x 900 at 60 Hz (digital input)  
1600 x 900 at 60 Hz (analog input)  
12 factory preset modes:  
H. freq (kHz)  
31.47  
31.47  
37.50  
37.88  
46.88  
48.36  
60.02  
44.77  
48.70  
63.89  
79.98  
60.00  
Resolution  
720*400  
V. freq (Hz)  
70.09  
59.94  
75.00  
60.32  
75.00  
60.00  
75.03  
59.86  
59.81  
60.02  
75.03  
60.00  
640*480  
640*480  
800*600  
800*600  
1024*768  
1024*768  
1280*720  
1280*800  
1280*1024  
1280*1024  
1600*900  
Automatic Power Saving  
If you have VESA DPM compliance display card or software installed in your PC, the monitor can automatically reduce  
its power consumption when not in use. If an input from a keyboard, mouse or other input device is detected, the  
monitor will 'wake up' automatically. The following table shows the power consumption and signaling of this automatic  
power saving feature:  
Power Management Definition  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/product/product.htm46)2009-5-2114:42:04  
   
ProductInformation  
LED  
color  
VESA Mode  
Active  
Video  
ON  
H-sync  
Yes  
V-sync  
Yes  
Power Used  
< 22 W (typ.),  
<24.5 W (max.)  
Green  
Sleep  
OFF  
OFF  
No  
-
No  
-
< 0.8 W (typ.)  
< 0.5W (typ.)  
Orange  
Switch Off  
Off  
®
®
This monitor is ENERGY STAR compliant. As an ENERGY STAR Partner, PHILIPS has  
®
determined that this product meets the ENERGY STAR guidelines for energy efficiency.  
*This data is subject to change without notice.  
The native resolution of the monitor is 1600 x 900, By default, your monitor has 100% (max.) 50% contrast, and 6500K  
color temperature, with full white pattern, without audio/USB.  
Product Views  
Follow the links to see various views of the monitor and its components.  
Physical Function  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/product/product.htm56)2009-5-2114:42:04  
   
ProductInformation  
1) Tilt  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/product/product.htm66)2009-5-2114:42:04  
PhilipsPixelDefectPolicy  
Philips Pixel Defect Policy  
Philips' Flat Panel Monitors Pixel Defect Policy  
Philips strives to deliver the highest quality products. We use some of the industry's most advanced  
manufacturing processes and practice stringent quality control. However, pixel or sub pixel defects on  
the TFT LCD panels used in flat panel monitors are sometimes unavoidable. No manufacturer can  
guarantee that all panels will be free from pixel defects, but Philips guarantees that any monitor with  
an unacceptable number of defects will be repaired or replaced under warranty. This notice explains  
the different types of pixel defects and defines acceptable defect levels for each type. In order to  
qualify for repair or replacement under warranty, the number of pixel defects on a TFT LCD panel  
must exceed these acceptable levels. For example, no more than 0.0004% of the sub pixels on a 19"  
XGA monitor may be defective. Furthermore, Philips sets even higher quality standards for certain  
types or combinations of pixel defects that are more noticeable than others. This policy is valid  
worldwide.  
Pixels and Sub pixels  
A pixel, or picture element, is composed of three sub pixels in the primary colors of red, green and  
blue. Many pixels together form an image. When all sub pixels of a pixel are lit, the three colored sub  
pixels together appear as a single white pixel. When all are dark, the three colored sub pixels together  
appear as a single black pixel. Other combinations of lit and dark sub pixels appear as single pixels of  
other colors.  
Types of Pixel Defects  
Pixel and sub pixel defects appear on the screen in different ways. There are two categories of pixel  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/product/pixel.htm14)2009-5-2114:42:22  
   
PhilipsPixelDefectPolicy  
defects and several types of sub pixel defects within each category.  
Bright Dot Defects Bright dot defects appear as pixels or sub pixels that are always lit or 'on'. That is,  
a bright dot is a sub-pixel that stands out on the screen when the monitor displays a dark pattern.  
There are the types of bright dot defects:  
Two adjacent lit sub pixels:  
- Red + Blue = Purple  
- Red + Green = Yellow  
One lit red, green or blue sub  
pixel  
Three adjacent lit sub pixels  
(one white pixel)  
- Green + Blue = Cyan (Light Blue)  
A red or blue bright dot must be more than 50 percent brighter than neighboring dots  
while a green bright dot is 30 percent brighter than neighboring dots.  
Black Dot Defects Black dot defects appear as pixels or sub pixels that are always dark or 'off'. That  
is, a dark dot is a sub-pixel that stands out on the screen when the monitor displays a light pattern.  
These are the types of black dot defects:  
One dark sub pixel  
Two or three adjacent dark sub pixels  
Proximity of Pixel Defects  
Because pixel and sub pixels defects of the same type that are near to one another may be more  
noticeable, Philips also specifies tolerances for the proximity of pixel defects.  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/product/pixel.htm24)2009-5-2114:42:22  
PhilipsPixelDefectPolicy  
Pixel Defect Tolerances  
In order to qualify for repair or replacement due to pixel defects during the warranty period, a TFT  
LCD panel in a Philips flat panel monitor must have pixel or sub pixel defects exceeding the  
tolerances listed in the following tables.  
BRIGHT DOT DEFECTS  
MODEL  
ACCEPTABLE LEVEL  
201E1  
1 lit subpixel  
3
2 adjacent lit subpixels  
1
3 adjacent lit subpixels (one white pixel)  
Distance between two bright dot defects*  
Total bright dot defects of all types  
0
>15mm  
3
BLACK DOT DEFECTS  
MODEL  
ACCEPTABLE LEVEL  
201E1  
1 dark subpixel  
5 or fewer  
2 or fewer  
0
2 adjacent dark subpixels  
3 adjacent dark subpixels  
Distance between two black dot defects*  
Total black dot defects of all types  
>15mm  
5 or fewer  
TOTAL DOT DEFECTS  
MODEL  
ACCEPTABLE LEVEL  
201E1  
Total bright or black dot defects of all types  
5 or fewer  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/product/pixel.htm34)2009-5-2114:42:22  
PhilipsPixelDefectPolicy  
Note:  
* 1 or 2 adjacent sub pixel defects = 1 dot defect  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/product/pixel.htm44)2009-5-2114:42:22  
SmartControl  
SmartControl II (Selective Models)  
Philips SmartControl II  
SmartControl II is monitor-based software with an easy-to-use on-screen graphic interface that guides you through fine-  
tuning resolution, color calibration and other display settings including brightness, contrast, clock & phase, position, RGB,  
white point and - on models with onboard speakers - volume adjustments.  
System support and requirement:  
1. Sytem support: 2000, XP, NT 4.0, XP 64 Edition, Vista 32/64. IE Support 6.0/7.0.  
2. Language support: English, Simplified Chinese, German, Spanish, French, Italian, Russian, Portuguese.  
3. Philips Monitor support DDC/CI Interface.  
Installation:  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/product/SM ART.HTM 1/17)2009-5-2114:42:38  
       
SmartControl  
Follow the instruction and complete the installation.  
You can lauch after installation complete.  
If you want to launch later, you can either click the shortcut on desktop or toolbar.  
Start to use:  
1. First launch –Wizard  
The first time after installation of SmartControl II, it will automatically go to Wizard for first time launch.  
The wizard will guide you through adjustment your monitor performance step by step.  
You can go to Plug-in menu to launch wizard later on as well.  
You can adjust more options without wizard by Standard pane.  
Wizard Analog Sequence  
Wizard Digital Sequence  
Resolution  
Focus  
Resolution  
Contrast  
Brightness  
Contrast  
Brightness  
White Point (Color Temp)  
Position  
File  
White Point (Color Temp)  
File  
-
-
2. Start with Standard pane:  
Adjust menu:  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/product/SM ART.HTM 2/17)2009-5-2114:42:38  
 
SmartControl  
Adjust Menu allow you to adjust Brightness, Contrast, Focus, Position and Resolution.  
You can follow the instruction and do the adjustment.  
Cancel prompts user if you want to cancel installation.  
Tab Heading  
Adjust  
Sub Menu  
Brightness  
Display in Analog  
Display in Digital  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
No  
Adjust  
Contrast  
Adjust  
Focus (Clock & Clock Phase)  
Position  
Adjust  
No  
Adjust  
Resolution  
Yes  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/product/SM ART.HTM 3/17)2009-5-2114:42:38  
SmartControl  
Color menu:  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/product/SM ART.HTM 4/17)2009-5-2114:42:38  
SmartControl  
Color Menu allow you to adjust RGB, Black Level, White Point, Color Calibration, and  
SmartImage (Please refer to SmartImage section).  
You can follow the instruction and do the adjustment.  
Refer to below table for sub-menu item base on your input.  
Example for Color Calibration  
Tab Heading  
Color  
Sub Menu  
RGB  
Display in Analog  
Display in Digital  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Color  
Black Level  
White Point  
Color Calibration  
Viewing Mode  
Color  
Color  
Color  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/product/SM ART.HTM 5/17)2009-5-2114:42:38  
SmartControl  
1. "Show Me" starts color calibration tutorial.  
2. Start - starts the 6-step color calibration sequence.  
3. Quick View loads the before/after images.  
4. To return to Color home pane, click the Cancel button.  
5. Enable color calibration - by default is on. If unchecked, does not allow for color calibration to happen, dimes out start and  
quick view buttons.  
6. Must have patent info in calibration screen.  
First color Calibration Screen:  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/product/SM ART.HTM 6/17)2009-5-2114:42:38  
SmartControl  
1. Previous button is disabled until the second color screen.  
2. Next goes to the succeeding target (6-targets).  
3. Final next goes File>Presets pane.  
4. Cancel closes the UI and returns to the plug in page.  
SmartImage - Allows user to change setting for better display setting based on content.  
When Entertainment is set, SmartContrast and SmartResponse are enabled.  
Plug-Ins - Asset Management Pane will only be active when selecting Asset Management from the drop-down Plug Ins  
menu.  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/product/SM ART.HTM 7/17)2009-5-2114:42:38  
SmartControl  
Displays Assent Management information on Managment, Description, Serial Number, Current Timing, Domain Name, and Asset  
Management Status.  
To return to Plug-in home pane select the plug-in tab.  
Plug-Ins - Theft Deterence Pane will only be active when selecting Theft from the drop-down Plug Ins menu.  
To enable Theft Deterrence, clicking Enable Theft button brings up the following screen:  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/product/SM ART.HTM 8/17)2009-5-2114:42:38  
SmartControl  
1. User can enter PIN between 4 and 9 digits numbers only.  
2. After entering PIN, Accept button takes user to the pop-up dialog box on the following page.  
3. Minimum minutes set to 5. Slider set to 5 by default.  
4. Does not require the display be attached to a different host to go into theft mode.  
Once a PIN is entered and accepted, the following dialog box appears:  
Click on No button takes user to the following screen.  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/product/SM ART.HTM 9/17)2009-5-2114:42:38  
SmartControl  
Click on Yes button takes user to secure web site landing page.  
After creating PIN, the Theft Deterrence pane will indicate Theft Deterrence Enabled and provide PIN Options button:  
1. Theft Deterrence Enabled is displayed.  
2. Disable Theft opens pane screen on next page.  
3. PIN Options button only available after user creates PIN, button opens secure PIN web site.  
Disable Theft button opens the following pane:  
1. After entering PIN, Accept button disables PIN.  
2. Cancel button opens up main Theft Deterrence pane, displaying Theft Deterrence Disabled. Enable Theft and PIN Options  
buttons.  
3. Entering incorrect PIN results in the following dialog box:  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/product/SM ART.HTM 10/17)2009-5-2114:42:38  
SmartControl  
Options>Preferences - Will only be active when selecting Preferences from the drop-down Options menu. On a non-  
supported display capable of DDC/CI, only the Help and Options tabs are available.  
1. Displays current preference settings.  
2. A checked box enables the feature. The check box is a toggle.  
3. Enable Context Menu on desktop is checked (On) by default. Enable Context menu displays SmartControl II selections for  
Select Preset and Tune Display in the desktop right-click context menu. Disabled removes SmartControl II from the right click  
context menu.  
4. Enable Task Tray icon is checked (On) by default. Enable context menu shows the task tray menu for SmartControl II. A right  
click on the task tray icon displays the menu options for Help, Technical Support. Check for Upgrade, About, and Exit. When  
Enable task tray menu is disabled, the task tray icon will only display EXIT.  
5. Run at Startup is checked (On) by default. When disabled, SmartControl II will not launch at start or be in the task tray. The  
only way to launch SmartControll II is either from the desktop short cut or from the program file. Any preset set to run at  
startup will not load when this box is unchecked (Disabled).  
6. Enable transparency mode (Vista, XP, and 2k only). Default is 0% Opaque.  
Options>Input - Will only be active when selecting Input from the drop-down Options menu. On a non-supported display  
capable of DDC/CI, only the Help and Options tabs are available. All other SmartControl II tabs are not available.  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/product/SM ART.HTM 11/17)2009-5-2114:42:38  
SmartControl  
1. Display the Source instruction pane and current input source setting.  
2. On single input displays, this pane will not be visible.  
Options>Auto - Will only be active when selecting Volume from the drop-down Options menu.  
On a non-supported display capable of DDC/CI, only the Help and Options tabs are available.  
Option>Auto Pivot  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/product/SM ART.HTM 12/17)2009-5-2114:42:38  
SmartControl  
Help>User Manual - Will only be active when selecting User Manual from the drop-down Help menu. On a non-supported  
display capable of DDC/CI, only the Help and Options tabs are available.  
Help>Version - Will only be active when selecting Version from the drop- down Help menu. On a non-supported display  
capable of DDC/CI, only the Help and Options tabs are available.  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/product/SM ART.HTM 13/17)2009-5-2114:42:38  
SmartControl  
Context Sensitive menu  
The Context Sensitive menu is Enabled by default. If Enable Context Menu has been checked in the Options>Preferences pane,  
then the menu will be visible.  
The Context Menu has four entries:  
1. SmartControll II - When selected the About Screen is displayed.  
2. Select Preset - Provides a hierarchical menu of saved presets for immediate use. A check mark shows the currently selected  
preset. Facoty Preset can also be called from the drop down menu.  
3. Tune Display - Opens the SmartControl II control panel.  
4. Fly off for SmartImage - Check current settings, Off, Office Work, ImageViewing, Entertainment, Economy.  
Task Tray Menu Enabled  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/product/SM ART.HTM 14/17)2009-5-2114:42:38  
SmartControl  
The task tray menu can be displayed by right-clicking on the SmartControl II icon from the task tray. Left Click will launch the  
application.  
The task tray has five entries:  
1. Help - Access to User Manual file: opnes User Manual file using the default browser window.  
2. Technical Support - displays the tech support page.  
3. Check for Update - takes the user to PDI Landing and checks the user's version against the most current available.  
4. About - Displays detailed reference information: product version, release information, and product name.  
5. Exit - Close SmartControll II. To run SmartControll II again either select SmartControll II from Program menu, double-click the  
desktop PC icon or restart the system.  
Task Tray Menu Disabled  
When the Task Tray is disabled in the preference folder, only the EXIT selection is available. To completely remove SmartControll II  
from the task tray, disable Run at Startup in Options>Preferences.  
Q&A  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/product/SM ART.HTM 15/17)2009-5-2114:42:38  
 
SmartControl  
Q1. I change the monitor on a PC to a different one and the SmartControl becomes un-usable, what do I do?  
A. Restart your PC and see if SmartControl can work. Otherwise, you will need to remove and re-install SmartControl to ensure  
proper driver is installed.  
Q2. The SmartControl functions well at the beginning, but it is not workable, what can I do?  
A. If the following actions were executed, the monitor driver may need to be re-installed.  
Change video graphic adapter to another one  
Update video driver  
Activities on OS, such as service pack or patch  
Run Windows Update and updated monitor and/or video driver  
Windows was booted with the monitor power off or disconnected.  
To find out, please right click My Computer and click on Properties->Hardware-> Device Manager.  
If you see "Plug and Play Monitor" shows under Monitor, then you need to re-install. Simply remove SmartControl and re-install it.  
Q3. After installing SmartControl, when clicking on SmartControl tab, nothing shows up after a while or a failure message shows,  
what happened?  
A. It might be your graphic adaptor is not compatible with the SmartControl. If your graphic adaptor is one of the above mentioned  
brands, try to download the most updated graphic adaptor driver from corresponding companies’ web site. Install the driver. Remove  
SmartControl, and re-install it once more.  
If it is still not working, we are sorry that the graphic adaptor is not supported. Please pay attention to Philips’ web site for any  
updated SmartControl driver available.  
Q4. When I click on Product Information, only partial information is shown, what happened?  
A. It might be your graphic card adaptor driver is not the most updated version which fully supporting DDC/CI interface. Please try to  
download the most updated graphic adaptor driver from corresponding companies’ web site. Install the driver. Remove  
SmartControl, and re-install it once more.  
Q5. I forgot my PIN for Theft Deterrence Function. How can I do?  
A. Please contact IT manager or Philips Service Center.  
Q6. In a monitor with the Smartlmage feature, the sRGB scheme of color temperature function in SmartControl is not responding,  
why?  
A. When Smartlmage is enabled, the sRGB scheme is disabled automatically. To use sRGB, you need to disable Smartlmage with  
the  
button at the front bezel of your monitor.  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/product/SM ART.HTM 16/17)2009-5-2114:42:38  
SmartControl  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/product/SM ART.HTM 17/17)2009-5-2114:42:38  
InstallingYourLCD M onitor  
Installing Your LCD Monitor  
Front View Product Description  
1
To switch monitor's power On and Off  
2
3
4
5
To access OSD menu  
MENU/  
To adjust brightness of the display.  
/
Auto picure control switching in wide and 4:3 format.  
Automatically adjust the horizontal position, vertical position,  
phase and clock settings/Return to previous OSD level.  
.
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/install/install.htm13)2009-5-2114:43:12  
     
InstallingYourLCD M onitor  
Rear View  
1
2
3
4
Kensington anti-thief lock  
VGA input  
DVI-D input (available for selective models)  
AC power input  
Optimizing Performance  
For best performance, ensure that your display settings are set at 1600x900, 60Hz.  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/install/install.htm23)2009-5-2114:43:12  
 
InstallingYourLCD M onitor  
Note: You can check the current display settings by pressing the 'OK' button  
once. The current display mode is shown in OSD main controls called  
RESOLUTION.  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/install/install.htm33)2009-5-2114:43:12  
ConnectingtoYourPC  
Connecting to Your PC  
Accessory Pack  
Unpack all the parts.  
DVI cable (Optional)  
Power cord  
EDFU pack  
VGA cable  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/install/connect.htm13)2009-5-2114:45:03  
     
ConnectingtoYourPC  
Connecting to Your PC  
1) Connect the power cord to the back of the monitor firmly. (Philips has pre-connected  
VGA cable for the first installation.  
* available for selective models  
* available for selective models  
2) Connect to PC  
(a)  
Turn off your computer and unplug its power cable.  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/install/connect.htm23)2009-5-2114:45:03  
 
ConnectingtoYourPC  
(b)  
Connect the monitor signal cable to the video connector on the back of your  
computer.  
(c)  
(d)  
Plug the power cord of your computer and your monitor into a nearby outlet.  
Turn on your computer and monitor. If the monitor displays an image,  
installation is complete.  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/install/connect.htm33)2009-5-2114:45:03  
TheBase  
The Base  
:
Attach and Detach the Base  
Attach the Base  
1) Firmly grasp the monitor with both hands. Attach the monitor stand to the monitor column until the tabs  
"click" into place before releasing the height adjustable column.  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/install/base.htm13)2009-5-2114:45:13  
   
TheBase  
Detach the Base  
You can remove the monitor body from the base and mount it on a wall, the commercial available arm with  
VESA standard hole (100x100mm)or Philips optional Super Ergo Base (for selective model).  
Remove the base  
Place the monitor face on a safe surface, push down on the release button and pull the base stand away  
from the monitor body.  
2) Remove the base from the LCD monitor.  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/install/base.htm23)2009-5-2114:45:13  
   
TheBase  
3) VESA mounting holes(100x100mm)  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/install/base.htm33)2009-5-2114:45:13  
GettingStarted  
Your LCD Monitor :  
Getting Started  
Getting Started  
Use the information file ( .inf) for Windows® 2000/XP/Vista or later  
The built-in VESA DDC2B feature in Philips Monitors supports Plug & Play requirements for  
Windows® 2000/XP/Vista. This information file ( .inf) should be installed in order that your  
Philips monitor can be enabled from the 'Monitor' dialog box in Windows® 2000/XP/Vista and  
the Plug & Play application can be activated. The installation procedure based on Windows®  
2000 , XP and Vista is specified as follows.  
For Windows® 2000  
1. Start Windows® 2000  
2. Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'.  
3. Double click on the 'Display' Icon.  
4. Select the 'Settings' tab then click on 'Advanced...'.  
5. Select 'Monitor'  
- If the 'Properties' button is inactive, it means your monitor is properly configured. Please  
stop installation.  
- If the 'Properties' button is active. Click on 'Properties' button. Please follow the steps  
given below.  
6. Click on 'Driver' and then click on 'Update Driver...' then click on the 'Next' button.  
7. Select 'Display a list of the known drivers for this device so that I can choose a specific  
driver', then click on 'Next' and then click on 'Have disk...'.  
8. Click on the 'Browse...' button then select the appropriate drive F: ( CD-ROM Drive).  
9. Click on the 'Open' button, then click on the 'OK' button.  
10. Select your monitor model and click on the 'Next' button.  
11. Click on the 'Finish' button then the 'Close' button.  
If you can see the 'Digital Signature Not Found' window, click on the 'Yes' button.  
For Windows® XP  
1. Start Windows® XP  
2. Click on the 'Start' button and then click on 'Control Panel'.  
3. Select and click on the category 'Printers and Other Hardware'  
4. Click on the 'Display' Item.  
5. Select the 'Settings' tab then click on the 'Advanced' button.  
6. Select 'Monitor' tab  
- If the 'Properties' button is inactive, it means your monitor is properly configured. Please  
stop installation.  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/install/gt_start.htm12)2009-5-2114:45:30  
     
GettingStarted  
- If the 'Properties' button is active, click on 'Properties' button.  
Please follow the steps below.  
7. Click on the 'Driver' tab and then click on 'Update Driver...' button.  
8. Select the 'Install from a list or specific location [advanced]' radio button and then click on  
the 'Next' button.  
9. Select the 'Don't Search. I will choose the driver to install' radio button. Then click on the  
'Next' button.  
10. Click on the 'Have disk...' button, then click on the 'Browse...' button and then select the  
appropriate drive F: (CD-ROM Drive).  
11. Click on the 'Open' button, then click the 'OK' button.  
12. Select your monitor model and click on the 'Next' button.  
- If you can see the 'has not passed Windows® Logo testing to verify its compatibility with  
Windows® XP' message, please click on the 'Continue Anyway' button.  
13. Click on the 'Finish' button then the 'Close' button.  
14. Click on the 'OK' button and then the 'OK' button again to close the Display_Properties  
dialog box.  
For Windows® Vista  
1. Start Windows® Vista  
2. Click the Start button; select and click on 'Control Panel'.  
3. Select and click on 'Hardware and Sound'  
4. Choose 'Device Manager' and Click on 'Update device drivers'.  
5. Select 'Monitor' and then right click on 'Generic PnP Monitor'.  
6. Click on 'Update Driver Software'.  
7. Select 'Browse my computer for driver software'.  
8. Click the 'Browse'button and choose the drive in which you've placed the disk. Example:  
(CD-ROM Drive:\\Lcd\PC\drivers\).  
9. Click the 'Next' button.  
10. Wait few minutes for installing the driver, and then click 'Close' button.  
If your Windows® 2000/XP/Vista version is different or you need more detailed installation  
information, please refer to your Windows® 2000/XP/Vista user's manual.  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/install/gt_start.htm22)2009-5-2114:45:30  
On-ScreenDisplay  
On-Screen Display  
Description of the On Screen Display  
What is the On-Screen Display?  
On-Screen Display (OSD) is a feature in all Philips LCD monitors. It allows an end user to adjust  
screen performance or select functions of the monitors directly through an on-screen instruction  
window. A user friendly on screen display interface is shown as below :  
Basic and simple instruction on the control keys.  
When you press the MENU/OK button on the front control of your monitor, the On-Screen Display  
(OSD) Main Controls window will pop up and you can then start making adjustments to your  
monitor's various features. Use the  
keys to make your adjustments.  
Dual model  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/osd/osddesc.htm15)2009-5-2114:48:56  
   
On-ScreenDisplay  
Analog model  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/osd/osddesc.htm25)2009-5-2114:48:56  
On-ScreenDisplay  
The OSD Tree  
Below is an overall view of the structure of the On-Screen Display. You can use this as a reference  
when you want to work your way around the different adjustments later on.  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/osd/osddesc.htm35)2009-5-2114:48:56  
 
On-ScreenDisplay  
Resolution notification  
This monitor is designed for optimal performance at its native resolution, 1600X900@60Hz. When  
the monitor is powered on at a different resolution, an alert is displayed on screen: Use  
1600x900@60Hz for best results.  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/osd/osddesc.htm45)2009-5-2114:48:56  
 
On-ScreenDisplay  
Display of the native resolution alert can be switched off from Setup in the OSD (On Screen  
Display) menu.  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/osd/osddesc.htm55)2009-5-2114:48:56  
CustomerCare& W arranty  
Customer Care & Warranty  
PLEASE SELECT YOUR COUNTRY/AREA TO REVIEW DETAILS OF YOUR  
WARRANTY COVERAGE  
WESTERN EUROPE: Austria Belgium Denmark France Germany Greece Finland  
EASTERN EUROPE: Czech Republic Hungary Poland Russia Slovakia Slovenia •  
LATIN AMERICA: Antilles Argentina Brasil Chile Colombia Mexico Paraguay •  
NORTH AMERICA: Canada USA  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/warranty/warranty.htm2009-5-2114:49:14  
 
YourPhilipsF1rstChoiceW arranty  
Your Philips F1rst Choice Warranty  
Thank you for purchasing this Philips monitor.  
All Philips monitors are designed and manufactured to high standards and deliver  
high-quality performance, ease of use and ease of installation. Should you  
encounter any difficulties while installing or using this product, please contact the  
Philips helpdesk directly to benefit from your Philips F1rst Choice Warranty. This  
three-year service warranty entitles you to a swap model on-site if your monitor  
turns out to be faulty or defective. Philips aims at a swap within 48 hours of your  
call being received.  
What is covered?  
The Philips F1rst Choice Warranty applies within Andorra, Austria, Belgium, Cyprus, Denmark,  
France, Germany, Greece, Finland, Ireland, Italy, Liechtenstein, Luxembourg, Monaco, the  
Netherlands, Norway, Poland, Portugal, Sweden, Switzerland, Spain and the United Kingdom and  
only for monitors originally designed, manufactured, approved and/or authorized for usage within  
these countries.  
Warranty coverage begins as from the day you buy your monitor. For three years thereafter, your  
monitor will be swapped by at least an equivalent monitor in case of defects provided for under the  
warranty coverage.  
The swap monitor remains yours and Philips keeps the defective/original monitor. For the swap  
monitor the warranty period remains equal to that of your original monitor, being 36 months as from  
the purchase date of your original monitor.  
What is excluded?  
The Philips F1rst Choice Warranty applies provided the product is handled properly for its intended  
use, in accordance with its operating instructions and upon presentation of the original invoice or  
cash receipt, indicating the date of purchase, dealer's name and model and production number of  
the product.  
The Philips F1rst Choice Warranty may not apply if:  
The documents have been altered in any way or made illegible;  
The model or production number on the product has been altered, deleted, removed or made  
illegible;  
Repairs or product modifications and alterations have been executed by unauthorized service  
organizations or persons;  
Damage is caused by accidents including but not limited to lightning, water or fire, misuse or  
neglect;  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/warranty/war_1st.htm13)2009-5-2114:49:19  
 
YourPhilipsF1rstChoiceW arranty  
Reception problems caused by signal conditions or cable or antenna systems outside the  
unit;  
Defects caused by abuse or misuse of the monitor;  
Product requires modification or adaptation to enable it to comply with local or national  
technical standards, which apply in countries for which the product was not originally  
designed, manufactured, approved and/or authorized. Therefore always check whether a  
product can be used in a specific country.  
Note that products that are not originally designed, manufactured, approved and/or  
authorized for usage within the Philips F1rst Choice countries, do not apply to the Philips  
F1rst Choice Warranty. In these cases the Philips global warranty terms are valid.  
Just a click away  
In case of any problems, we advise you to read the operating instructions carefully or go to the www.  
philips.com/support website for additional support.  
Just a phone call away  
In order to avoid unnecessary inconvenience, we advise you to read the operating instructions  
carefully or go to the www.philips.com/support website for additional support before contacting the  
Philips helpdesk.  
To solve your problem quickly, please prepare the following details before contacting the Philips  
helpdesk:  
Philips type number  
Philips serial number  
Purchase date (copy of purchase may be required)  
PC environment Processor:  
CUP and Graphic card name and driver version  
Operating system  
Application being used  
Other cards installed  
Having the following information available will also help speed up the process:  
Your proof of purchase indicating: date of purchase, dealer name, model and product serial  
number.  
The full address to which the faulty monitor has to be collected and the swap model should  
be delivered.  
Philips' customer help desks are located worldwide. Click here to access the F1rst Choice Contact  
Or you can reach us via:  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/warranty/war_1st.htm23)2009-5-2114:49:19  
YourPhilipsF1rstChoiceW arranty  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/warranty/war_1st.htm33)2009-5-2114:49:19  
F1rstChoiceContactInformation  
F1rst Choice Contact Information  
Country  
Code  
+43  
+32  
+45  
+358  
+33  
+49  
+30  
+353  
+39  
+352  
+31  
+47  
+48  
+351  
+34  
+46  
+41  
+44  
Telephone number  
0810 000206  
078 250851  
Tariff  
Austria  
0.07  
Belgium  
Denmark  
Finland  
0.06  
3525 8761  
Local call tariff  
Local call tariff  
0.09  
09 2290 1908  
082161 1658  
01803 386 853  
00800 3122 1223  
01 601 1161  
840 320 041  
26 84 30 00  
France  
Germany  
Greece  
0.09  
Free of charge  
Local call tariff  
0.08  
Ireland  
Italy  
Luxembourg  
The Netherlands  
Norway  
Local call tariff  
0.10  
0900 0400 063  
2270 8250  
Local call tariff  
Local call tariff  
Local call tariff  
0.10  
Poland  
0223491505  
2 1359 1440  
902 888 785  
08 632 0016  
02 2310 2116  
0207 949 0069  
Portugal  
Spain  
Sweden  
Switzerland  
United Kingdom  
Local call tariff  
Local call tariff  
Local call tariff  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/warranty/warfirst.htm2009-5-2114:49:31  
 
YourGuaranteeinCentralandEasternEurope  
Your Guarantee in Central and Eastern Europe  
Dear Customer,  
Thank you for purchasing this Philips product, which has been designed and manufactured to the  
highest quality standards. If, unfortunately, something should go wrong with this product Philips  
guarantees free of charge labor and replacement parts during a period of 36 months from date of  
purchase.  
What is covered?  
This Philips Guarantee in Central and Eastern Europe applies within Czech Republic, Hungary,  
Slovakia, Slovenia, Russia and Turkey and only for monitors originally designed, manufactured,  
approved and/or authorized for usage within these countries.  
Warranty coverage begins as from the day you buy your monitor. For 3 years thereafter, your  
monitor will be serviced in case of defects provided for under the warranty coverage.  
What is excluded?  
The Philips guarantee applies provided the product is handled properly for its intended use, in  
accordance with its operating instructions and upon presentation of the original invoice or cash  
receipt, indicating the date of purchase, dealer's name and model and production number of the  
product.  
The Philips guarantee may not apply if:  
the documents have been altered in any way or made illegible;  
the model or production number on the product has been altered, deleted, removed or made  
illegible;  
repairs or product modifications and alterations have been executed by unauthorized service  
organizations or persons;  
damage is caused by accidents including but not limited to lightning, water or fire, misuse or  
neglect.  
Reception problems caused by signal conditions or cable or antenna systems outside the  
unit;  
Defects caused by abuse or misuse of the monitor;  
Product requires modification or adaptation to enable it to comply with local or national  
technical standards, which apply in countries for which the product was not originally  
designed, manufactured, approved and/or authorized. Therefore always check whether a  
product can be used in a specific country.  
Please note that the product is not defective under this guarantee in the case where modifications  
become necessary in order for the product to comply with local or national technical standards  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/warranty/war_ee.htm12)2009-5-2114:49:54  
 
YourGuaranteeinCentralandEasternEurope  
which apply in countries for which the product was not originally designed and/or manufactured.  
Therefore always check whether a product can be used in a specific country.  
Just a click away  
In case of any problems, we advise you to read the operating instructions carefully or go to the www.  
philips.com/support website for additional support.  
Just a phone call away  
In order to avoid unnecessary inconvenience, we advise you to read the operating instructions  
carefully before contacting our dealers or Information Centers  
In case your Philips product is not working correctly or is defective, please contact your Philips  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/warranty/war_ee.htm22)2009-5-2114:49:54  
ConsumerInformationCenters  
Consumer Information Centers  
Eastern Europe  
BELARUS  
Technical Center of JV IBA  
M. Bogdanovich str. 155  
BY - 220040 Minsk  
Tel: +375 17 217 33 86  
BULGARIA  
LAN Service  
140, Mimi Balkanska Str.  
Office center Translog  
1540 Sofia, Bulgaria  
Tel: +359 2 960 2360  
CZECH REPUBLIC  
General Consumer Information Center  
800 142100  
Xpectrum  
Lu.ná 591/4  
CZ - 160 00 Praha 6 Tel: 800 100 697  
Email:info@xpectrum.cz  
CROATIA  
Renoprom d.o.o.  
Mlinska 5, Strmec  
HR - 41430 Samobor  
Tel: +385 1 333 0974  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/warranty/warcic.htm1/10)2009-5-2114:50:10  
         
ConsumerInformationCenters  
ESTONIA  
FUJITSU SERVICES OU  
Akadeemia tee 21G  
EE-12618 Tallinn  
Tel: +372 6519900  
HUNGARY  
General Consumer Information Center  
0680018544 (Local call tariff)  
Serware Szerviz  
Vizimolnár u. 2-4  
HU - 1031 Budapest  
Tel: +36 1 2426331  
Email: inbox@serware.hu  
HUNGARY  
General Consumer Information Center  
0680018544 (Local call tariff)  
Profi Service Center Ltd.  
123 Kulso-Vaci Street ,  
H-1044 Budapest ( Europe Center )  
Hungary  
Tel: +36 1 814 8080  
LATVIA  
ServiceNet LV  
Jelgavas iela 36  
LV - 1055 Riga,  
Tel: +371 7460399  
Email: serviss@servicenet.lv  
LITHUANIA  
ServiceNet LT  
Gaiziunu G. 3  
LT - 3009 KAUNAS  
Tel: +370 7400088  
Email: servisas@servicenet.lt  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/warranty/warcic.htm2/10)2009-5-2114:50:10  
       
ConsumerInformationCenters  
ROMANIA  
Blue Ridge Int'l Computers SRL  
115, Mihai Eminescu St., Sector 2  
RO - 020074 Bucharest  
Tel: +40 21 2101969  
SERBIA & MONTENEGRO  
Tehnicom Service d.o.o.  
Viline vode bb  
Slobodna zona Beograd , L12/4  
Belgrade 11000  
Tel. +381 11 2070 664  
Serbia  
SLOVAKIA  
General Consumer Information Center  
0800004551  
Datalan Servisne Stredisko  
Puchovska 8  
SK - 831 06 Bratislava  
Tel: +421 2 49207155  
Email: servis@datalan.sk  
SLOVENIA  
PC HAND  
Brezovce 10  
SI - 1236 Trzin  
Tel: +386 1 530 08 24  
Email: servis@pchand.si  
RUSSIA  
Tel: +7 095 961-1111  
Tel: 8-800-200-0880  
TURKEY  
Türk Philips Ticaret A.S.  
Yukari Dudullu Org.San.Bolgesi  
2.Cadde No:22  
34776-Umraniye/Istanbul  
Tel: (0800)-261 33 02  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/warranty/warcic.htm3/10)2009-5-2114:50:10  
           
ConsumerInformationCenters  
UKRAINE  
Comel  
Shevchenko street 32  
UA - 49030 Dnepropetrovsk  
Tel: +380 562320045  
Latin America  
ANTILLES  
Philips Antillana N.V.  
Kaminda A.J.E. Kusters 4  
Zeelandia, P.O. box 3523-3051  
Willemstad, Curacao  
Phone: (09)-4612799  
Fax : (09)-4612772  
ARGENTINA  
Philips Antillana N.V.  
Vedia 3892 Capital Federal  
CP: 1430 Buenos Aires  
Phone/Fax: (011)-4544 2047  
BRASIL  
Philips da Amazônia Ind. Elet. Ltda.  
Rua Verbo Divino, 1400-São Paulo-SP  
CEP-04719-002  
Phones: 11 21210203 -São Paulo & 0800-701-0203-Other Regions without São Paulo City  
CHILE  
Philips Chilena S.A.  
Avenida Santa Maria 0760  
P.O. box 2687Santiago de Chile  
Phone: (02)-730 2000  
Fax : (02)-777 6730  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/warranty/warcic.htm4/10)2009-5-2114:50:10  
         
ConsumerInformationCenters  
COLOMBIA  
Industrias Philips de Colombia  
S.A.-Division de Servicio  
CARRERA 15 Nr. 104-33  
Bogota, Colombia  
Phone:(01)-8000 111001 (toll free)  
Fax : (01)-619-4300/619-4104  
MEXICO  
Consumer Information Centre  
Norte 45 No.669  
Col. Industrial Vallejo  
C.P.02300, -Mexico, D.F.  
Phone: (05)-3687788 / 9180050462  
Fax : (05)-7284272  
PARAGUAY  
Av. Rca. Argentina 1780 c/Alfredo Seiferheld  
P.O. Box 605  
Phone: (595 21) 664 333  
Fax: (595 21) 664 336  
Customer Desk:  
Phone: 009 800 54 1 0004  
PERU  
Philips Peruana S.A.  
Customer Desk  
Comandante Espinar 719  
Casilla 1841  
Limab18  
Phone: (01)-2136200  
Fax : (01)-2136276  
URUGUAY  
Rambla O'Higgins 5303 Montevideo  
Uruguay  
Phone: (598) 619 66 66  
Fax: (598) 619 77 77  
Customer Desk:  
Phone: 0004054176  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/warranty/warcic.htm5/10)2009-5-2114:50:10  
         
ConsumerInformationCenters  
VENEZUELA  
Industrias Venezolanas Philips S.A.  
Apartado Postal 1167  
Caracas 1010-A  
Phone: (02) 2377575  
Fax : (02) 2376420  
Canada  
CANADA  
Philips Electronics Ltd.  
281 Hillmount Road  
Markham, Ontario L6C 2S3  
Phone: (800) 479-6696  
Pacific  
AUSTRALIA  
Philips Authorized Service Center  
Company: AGOS NETWORK PTY LTD  
Address: 4/5 Dursley Road, Yenorra, NSW 2161, Australia  
Tel: 1300 360 386  
Fax: +61-2-96816666  
Email: philips@agos.com.au  
Service hours: Mon.~Fri. 8:00am-7:30pm  
NEW ZEALAND  
Philips Authorized Service Center  
Company: Visual Group Ltd.  
Address: 28 Walls Rd Penrose Auckland  
Phone: 0800 657447  
Fax: 09 5809607  
E-mail: vai.ravindran@visualgroup.co.nz  
Service Hours: Mon.~Fri. 8:30am~5:30pm  
Asia  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/warranty/warcic.htm6/10)2009-5-2114:50:10  
     
ConsumerInformationCenters  
HONG KONG/Macau  
Company : PHK Service Limited  
Address: Flat A, 10/F., Pak Sun Building, 103 - 107 Wo Yi Hop Road, Kwai Chung, New Territories, Hong  
Kong  
Tel.: (852) 2610-6908 / (852) 2610-6929 for Hong Kong and (853) 2856-2277 for Macau  
Fax: (852) 2485 3574 for Hong Kong and (853) 2856 1498 for Macau  
E-mail: cslam@phkservice.com.hk  
Service Hours: Mon.~Sat. 09:00am~06:00pm  
India  
Philips Authorized Service Center  
Company: REDINGTON INDIA LTD  
Address: SPL Guindy House, 95 Mount Road, Chennai 600032, India  
Tel: +9144-42243352/353  
E-mail: aftersales@in.aocmonitor.com  
Service hours: Mon.~Fri. 9:00AM~5:30PM; Sat. 9:00AM~1:00PM  
Indonesia  
Philips Authorized Service Center Company : PT. Gadingsari elektronika Prima Address: Komplek Pinang 8,  
Jl. Ciputat raya No. 8F, Pondok Pinang Tel: 021-70909053, 021-70909056 Fax: 021-7510982 E-mail:  
gepta@cbn.net.id Service hours: Mon.~Fri. 8:30am~4:30pm; Sat. 8:30am~2:00pm Philips Authorized  
Service Center  
Company : PT. Gadingsari elektronika Prima  
Address: Komplek Pinang 8, Jl. Ciputat raya No. 8F, Pondok Pinang  
Tel: 021-70909053, 021-70909056  
Fax: 021-7510982  
E-mail: gepta@cbn.net.id  
Service hours: Mon.~Fri. 8:30am~4:30pm; Sat. 8:30am~2:00pm  
South Korea  
Philips Authorized Service Center  
Company: PCS One Korea Ltd.  
Address: 112-2, Banpo-dong, Seocho-ku, Seoul, 137-040, Korea  
Call Center Tel: 080-600-6600  
Tel: 82 2 591 1528  
Fax: 82 2 595 9688  
E-mail: svc_hkkim@philips.com  
Service hours: Mon.~Fri. 9:00AM~ 6:00PM; Sat. 9:00AM~1:00PM  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/warranty/warcic.htm7/10)2009-5-2114:50:10  
       
ConsumerInformationCenters  
Malaysia  
Philips Authorized Service Center  
Company: After Market Solutions (CE) Sdn Bhd  
Address: Lot 6. Jalan 225/51A, 46100 Petaling Jaya, Selangor DE, Malaysia.  
Phone: 603 7953 3370  
Philips Info Line: 1-800-880-180  
Fax: 603 7953 3338  
E-mail: pceinfo.my@philips.com  
Service Hours: Mon.~Fri. 8:15am~5:15pm; Sat. 9:00am~1:00pm  
Pakistan  
Philips Consumer Service  
Address: Mubarak manzil, 39, Garden Road, Saddar, Karachi-74400  
Tel: (9221) 2737411-16  
Fax: (9221) 2721167  
E-mail: care@philips.com  
Singapore  
Company: Philips Electronics Singapore Pte Ltd (Philips Consumer Care Center)  
Address: 620A Lorong 1 Toa Payoh, TP4 Building Level 1, Singapore 319762  
Tel: (65) 6882 3999  
Fax: (65) 62508037  
E-mail: consumer.care.sg@philips.com  
Service hours: Mon.~Fri. 9:00am~6:00pm; Sat. 9:00am~1:00pm  
Taiwan  
Philips Authorized Service Center  
Company: FETEC.CO  
Address: 3F, No.6, Lane 205, Sec. 1, Chang Hsing Rd, Lu Chu Hs, Taoyuan, Taiwan R.O.C 33800  
Consumer Care: 0800-231-099  
Tel: (03)2120336  
Fax: (03)3129184  
E-mail: knlin08@xuite.net  
Service hours: Mon.~Fri. 9:00am~6:00pm  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/warranty/warcic.htm8/10)2009-5-2114:50:10  
     
ConsumerInformationCenters  
Thailand  
Philips Authorized Service Center  
Company: Axis Computer System Co., Ltd.  
Address: 1421 Soi Lardprao 94, Srivara Town In Town Soi 3 Road, Wangthonglang, Bangkok 10310  
Thailand  
Tel: (662) 934-5498  
Fax: (662) 934-5499  
E-mail: axis5@axiscomputer.co.th  
Service Hours: Mon.~Fri. 08:30am~05:30pm  
Middle East + North Africa  
Philips Authorized Service Center  
Company: AL SHAHD COMPUTER L.L.C  
Address: P.O.BOX: 29024, DUBAI, UNITED ARAB EMIRATES  
TEL: 00971 4 2276525  
FAX: 00971 4 2276242  
E-mail: shahd52@eim.ae  
Service hours: Sat.~Thur. 9:00am~1:00pm & 4:00pm- 8:00pm  
Israel  
Philips Authorized Service Center  
Company: Eastronics LTD  
Address: 13 Rozanis St. P.O.B. 39300, Tel Aviv 61392 Israel  
Tel: 1-800-567000 call free in Israel; (972-50-8353722 after service hours until 20:00)  
Fax: 972-3-6458759  
E-mail: eastronics@eastronics.co.il  
Service hours: Sun.~Thurs. 08:00 - 18:00  
Africa  
MOROCCO  
Philips Electronique Maroc  
304,BD Mohamed V  
Casablanca  
Phone: (02)-302992  
Fax : (02)-303446  
SOUTH AFRICA  
Philips Authorized Service Center  
Company : Sylvara Technologies Pty Ltd  
Address: Ho Address Palm Springs Centre Christoffel Road Van Riebeeck Park Kempton Park, South Africa  
Tel: +27878084456  
Fax: +2711 391 1060  
E-mail: customercare@philipssupport.co.za  
Service hours: Mon.~ Fri. 08:00am~05:00pm  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/warranty/warcic.htm9/10)2009-5-2114:50:10  
         
ConsumerInformationCenters  
Middle East  
United Arab Emirates  
Philips Middle East B.V.  
Consumer Information Centre  
P.O.Box 7785  
DUBAI  
Phone: (04)-335 3666  
Fax : (04)-335 3999  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/warranty/warcic.htm10/10)2009-5-2114:50:10  
 
InternationalGuarantee  
Your International Guarantee  
Dear Customer,  
Thank you for purchasing this Philips product which has been designed and manufactured to the  
highest quality standards.  
If, unfortunately, something should go wrong with this product Philips guarantees free of charge  
labor and replacement parts irrespective of the country where it is repaired during a period of 12  
months from date of purchase. This international Philips guarantee complements the existing  
national guarantee obligations to you of dealers and Philips in the country of purchase and does not  
affect your statutory rights as a customer.  
The Philips guarantee applies provided the product is handled properly for its intended use, in  
accordance with its operating instructions and upon presentation of the original invoice or cash  
receipt, indicating the date of purchase, dealer's name and model and production number of the  
product.  
The Philips guarantee may not apply if:  
the documents have been altered in any way or made illegible;  
the model or production number on the product has been altered, deleted, removed or made  
illegible;  
repairs or product modifications and alterations have been executed by unauthorized service  
organizations or persons;  
damage is caused by accidents including but not limited to lightning, water or fire, misuse or  
neglect.  
Please note that the product is not defective under this guarantee in the case where modifications  
become necessary in order for the product to comply with local or national technical standards  
which apply in countries for which the product was not originally designed and/or manufactured.  
Therefore always check whether a product can be used in a specific country.  
In case your Philips product is not working correctly or is defective, please contact your Philips  
dealer. In the event you require service whilst in another country a dealer address can be given to  
you by the Philips Consumer Help Desk in that country, the telephone and fax number of which can  
be found in the relevant part of this booklet.  
In order to avoid unnecessary inconvenience, we advise you to read the operating instructions  
carefully before contacting your dealer. If you have questions which your dealer cannot answer or  
any related question please contact the Philips Consumer Information Centers or via:  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/warranty/war_intl.htm12)2009-5-2114:51:04  
 
InternationalGuarantee  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/warranty/war_intl.htm22)2009-5-2114:51:04  
UnitedStatesGuarantee  
Your Philips F1rst Choice Warranty(USA)  
Thank you for purchasing this Philips monitor.  
All Philips monitors are designed and manufactured to high standards and  
deliver high-quality performance, ease of use and ease of installation. Should  
you encounter any difficulties while installing or using this product, please  
contact Philips directly to benefit from your Philips F1rst Choice Warranty. This  
three-year service warranty entitles you to a swap model on-site within 48  
hours of your call being received within the first year of purchase. If you have  
any problems with your monitor within the second or third year of purchase, we  
will repair it after it has been sent to the service provider at your expense and  
returned to you within five working days, free of charge.  
LIMITED WARRANTY (Computer Monitor)  
Click here to access the Warranty Registration Card.  
Three Years Free Labor / Three Years Free Service on Parts / One Year Exchange*  
*Product will be exchanged with a new or renewed to original specifications unit within two  
business days for the first year. This product must be shipped in at your expense for service during  
years two and three.  
WHO IS COVERED?  
You must have proof of purchase to receive warranty service. A sales receipt or other document  
showing that you purchased the product is considered proof of purchase. Attach it to this owner's  
manual and keep both nearby.  
WHAT IS COVERED?  
Warranty coverage begins the day you buy your product. For three years thereafter, all parts will be  
repaired or replaced, and labor is free. After three years from the day of purchase, you pay for the  
replacement or repair of all parts, and for all labor charges.  
All parts, including repaired and replaced parts, are covered only for the original warranty period.  
When the warranty on the original product expires, the warranty on all replaced and repaired  
products and parts also expires.  
WHAT IS EXCLUDED?  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/warranty/war_usa.htm14)2009-5-2114:51:18  
 
UnitedStatesGuarantee  
Your warranty does not cover:  
labor charges for installation or setup of the product, adjustment of customer controls on the  
product, and installation or repair of antenna systems outside of the product.  
product repair and/or part replacement because of misuse, accident, unauthorized repair or  
other cause not within the control of Philips Consumer Electronics.  
reception problems caused by signal conditions or cable or antenna systems outside the  
unit.  
a product that requires modification or adaptation to enable it to operate in any country other  
than the country for which it was designed, manufactured, approved and/or authorized, or  
repair of products damaged by these modifications.  
incidental or consequential damages resulting from the product. (Some states do not allow  
the exclusion of incidental or consequential damages, so the above exclusion may not apply  
to you. This includes, but is not limited to, prerecorded material, whether copyrighted or not  
copyrighted.)  
the model or production number on the product has been altered, deleted, removed or made  
illegible.  
Where IS SERVICE AVAILABLE?  
Warranty service is available in all countries where the product is officially distributed by Philips  
Consumer Electronics. In countries where Philips Consumer Electronics does not distribute the  
product, the local Philips service organization will attempt to provide service (although there may be  
a delay if the appropriate spare parts and technical manual(s) are not readily available).  
Where CAN I GET MORE INFORMATION?  
For more information, contact the Philips Customer Care Center by calling (877) 835-1838 (U.S.A.  
customers only) or (919) 573-7855.  
Before Requesting Service...  
Please check your owner's manual before requesting service. Adjustments of the controls  
discussed there may save you a service call.  
TO GET WARRANTY SERVICE IN U.S.A., PUERTO RICO OR U.S. VIRGIN ISLANDS...  
Contact the Philips Customer Care Center phone number listed below for product assistance and  
procedures for servicing:  
Philips Customer Care Center  
(877) 835-1838 or (919) 573-7855  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/warranty/war_usa.htm24)2009-5-2114:51:18  
UnitedStatesGuarantee  
(In U.S.A., Puerto Rico and U.S. Virgin Islands, all implied warranties, including implied warranties  
of merchantability and fitness for a particular purpose, are limited in duration to the duration of this  
express warranty. But, because some states do not allow limitations on how long an implied  
warranty may last, this limitation may not apply to you.)  
TO GET WARRANTY SERVICE IN CANADA...  
Please contact Philips at:  
(800) 479-6696  
Three years free parts and three years free labor will be provided at Philips Canada depot or any  
one of its authorized service centers.  
(In Canada, this warranty is given in lieu of all other warranties. No other warranties are expressed  
or implied, including any implied warranties of merchantability or fitness for a particular purpose.  
Philips is not liable under any circumstances for any direct, indirect, special, incidental or  
consequential damages, howsoever incurred, even if notified of the possibility of such damages.)  
REMEMBER... Please record the model and serial numbers found on the product below.  
MODEL # ________________________________________________  
SERIAL # ________________________________________________  
This warranty gives you specific legal rights. You may have other rights which vary from state/  
province to state/province.  
Before contacting Philips, please prepare the following details so we can solve your problem  
quickly.  
Philips type number  
Philips serial number  
Purchase date (copy of purchase may be required)  
PC environment Processor:  
CUP and Graphic card name and driver version  
Operating system  
Application being used  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/warranty/war_usa.htm34)2009-5-2114:51:18  
UnitedStatesGuarantee  
Other cards installed  
Having the following information available will also help speed up the process:  
Your proof of purchase indicating: date of purchase, dealer name, model and product serial  
number.  
The full address to which the swap model should be delivered.  
Just a phone call away  
Philips’ customer help desks are located worldwide. Within the U.S. you can contact Philips  
customer care Monday-Friday from 8:00 AM-9:00 PM Eastern Time (ET) and on Saturdays from  
10:00 AM-5:00 PM ET hrs by using one of the contact phone numbers.  
For more information on this and more great Philips products visit our website at:  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/warranty/war_usa.htm44)2009-5-2114:51:18  
DownloadandPrint  
Download and Print  
Installing Your LCD monitor driver  
System requirements:  
PC running Windows® 2000 , Windows® XP, Windows® Vista or later  
Find your driver ".inf/.icm/.cat" at : /PC/drivers/  
Read the "Readme.txt" file before installing.  
Add” refer to http://www.p4c.philips.com/ to download the latest version of monitor drivers.”  
This page provides an option to read the manual in .pdf format. PDF files can be downloaded into  
your hard disk, then viewed and printed with Acrobat Reader or through your browser.  
If you do not have Adobe® Acrobat Reader installed, click on the link to install the application.  
Download instructions:  
To download the file:  
1. Click-and-hold your mouse over the icon below. (Windows® 95/98/2000/Me/XP/Vista users right-  
click)  
Download  
2. From the menu that appears, choose 'Save Link As...', 'Save Target As...' or 'Download Link to  
Disk'.  
3. Choose where you would like to save the file; click 'Save' (if prompted to save as either 'text' or  
'source', choose 'source').  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/download/download.htm12)2009-5-2114:51:46  
       
DownloadandPrint  
Printing instructions:  
To print the manual:  
With the manual file open, follow your printer's instructions and print the pages you need.  
file:///G|/201E1/201E1/lcd/manual/ENGLISH/download/download.htm22)2009-5-2114:51:46  

KitchenAid KEBC247K User Manual
KitchenAid KEBS177Y User Manual
KitchenAid KGCS166GBT2 User Manual
Moen CRT Television L3175 User Manual
Moffat Waldorf CN1100GC User Manual
NEC MultiSync JC 1941UMA User Manual
Oricom ULTRA 9800 User Manual
Philips 20PT6431 User Manual
Philips Computer Monitor 240BW9 User Manual
Philips DVP3510 User Manual