e-M anual
Philips LCD Monitor Electronic User’s Manual
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/INDEX.HTM 2010-1-1111:53:00
SafetyandTroubleshootingInformation
extreme cold.
●
In order to maintain the best performance of your monitor and use it for a longer lifetime,
please use the monitor in a location that falls within the following temperature and
humidity ranges.
❍
Temperature: 0-40°C 32-104°F
Humidity: 20-80% RH
❍
Service:
●
●
The casing cover should be opened only by qualified service personnel.
If there is any need for any document for repair or integration, please contact with your
local service center. (please refer to the chapter of "Consumer Information Center")
For transportation information, please refer to "Physical Specifications".
Do not leave your monitor in a car/trunk under direct sun light.
●
●
Consult a service technician if the monitor does not operate normally, or you are
not sure what procedure to take when the operating instructions given in this
manual have been followed.
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/safety/safety.htm（第2／2页）2010-1-1111:53:02
FAQs(FrequentlyAskedQuestions)
FAQs (Frequently Asked Questions)
General FAQs
Q: When I install my monitor what should I do if the screen shows 'Cannot display this video
mode'?
A: Recommended video mode for Philips : 1366 x 768 @60Hz.
1. Unplug all cables, then connect your PC to the monitor that you used
previously.
2. In the Windows Start Menu, select Settings/Control Panel. In the Control Panel
Window, select the Display icon. Inside the Display Control Panel, select the
'Settings' tab. Under the setting tab, in box labeled 'desktop area', move the
slidebar to 1366 x 768 pixels .
3. Open 'Advanced Properties' and set the Refresh Rate to 60Hz, then click OK.
4. Restart your computer and repeat step 2 and 3 to verify that your PC is set at
1366 x 768@60Hz .
5. Shut down your computer, disconnect your old monitor and reconnect your
Philips LCD monitor.
6. Turn on your monitor and then turn on your PC.
Q: What does 'refresh rate' mean in connection with an LCD monitor?
A: The refresh rate is of much less relevance for LCD monitors. LCD monitors display
a stable, flicker-free image at 60Hz. There is no visible difference between 85Hz and
60Hz.
Q: What are the .inf and .icm files on the CD-ROM? How do I install the drivers (.inf and .
icm)?
A: These are the driver files for your monitor. Follow the instructions in your user
manual to install the drivers. Your computer may ask you for monitor drivers (.inf and .
icm files) or a driver disk when you first install your monitor. Follow the instructions to
insert the ( companion CD-ROM) included in this package. Monitor drivers (.inf and .
icm files) will be installed automatically.
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/safety/saf_faq.htm（第1／6页）2010-1-1111:53:04
FAQs(FrequentlyAskedQuestions)
Q: How do I adjust the resolution?
A: Your video card/graphic driver and monitor together determine the available
resolutions. You can select the desired resolution under Windows® Control Panel
with the "Display properties".
Q: What if I get lost when I am making monitor adjustments?
A: Simply press the MENU button, then select 'Reset' to recall all of the original
factory settings.
Q: What is the Auto function?
A: The AUTO adjustment key restores the optimal screen position, phase and clock
settings by pressing of a single button – without the need to navigate through OSD
(On Screen Display) menus and control keys.
Note: Auto function is available in selected models only.
Q: My Monitor has no power (Power LED does not light up). What should I do?
A: Make sure the AC power cord is connected between the monitor and AC outlet,
and click a key on keyboard/mouse to wake up the PC.
Q: Will the LCD monitor accept an interlaced signal under PC models?
A: No. If an Interlace signal is used, the screen displays both odd and even horizontal
scanning lines at the same time, thus distorting the picture.
Q: What does the Refresh Rate mean for LCD?
A: Unlike CRT display technology, in which the speed of the electron beam is swept
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/safety/saf_faq.htm（第2／6页）2010-1-1111:53:04
FAQs(FrequentlyAskedQuestions)
from the top to the bottom of the screen determines flicker, an active matrix display
uses an active element (TFT) to control each individual pixel and the refresh rate is
therefore not really applicable to LCD technology.
Q: Will the LCD screen be resistant to scratches?
A: A protective coating is applied to the surface of the LCD, which is durable to a
certain extent (approximately up to the hardness of a 2H pencil). In general, it is
recommended that the panel surface is not subject to any excessive shocks or
scratches.
Q: How should I clean the LCD surface?
A: For normal cleaning, use a clean, soft cloth. For extensive cleaning, please use
isopropyl alcohol. Do not use other solvents such as ethyl alcohol, ethanol, acetone,
hexane, etc.
Q:Can I change the color setting of my monitor?
A:Yes, you can change your color setting through OSD control as the following
procedures,
1. Press "MENU" to show the OSD (On Screen Display) menu
2. Press "Arrow" to select the option "color" then press "MENU" to enter color setting,
there are four settings as below.
a. 6500K; this setting features the panel closed to red-white color tone.
b. 9300K; this setting features the panel closed to blue-white color tone.
c. User Define; the user can choose his/her preference color setting by
adjusting red, green, blue color.
d. sRGB; this is a standard setting for ensuring correct exchange of
colors between different device (e.g. digital cameras, monitors, printers,
scanners, etc.)
*A measurement of the color of light radiated by an object while it is being heated. This measurement
is expressed in terms of absolute scale, (degrees Kelvin). Lower Kevin temperatures such as 2004K
are red; higher temperatures such as 9300K are blue. Neutral temperature is white, at 6504K.
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/safety/saf_faq.htm（第3／6页）2010-1-1111:53:04
FAQs(FrequentlyAskedQuestions)
Q: Can the Philips LCD Monitor be mounted on the wall?
A: Yes. Philips LCD monitors have this optional feature. For standard VESA mount
holes on the rear cover allows the user to mount the Philips monitor on most of the
VESA standard arms or accessories. We recommend to contact your Philips sales
representative for more information.
Screen Adjustments
Q: How do LCDs compare to CRTs in terms of radiation?
A: Because LCDs do not use an electron gun, they do not generate the same amount
of radiation at the screen surface.
Compatibility with other Peripherals
Q: Are Philips LCD monitors Plug-and-Play?
A: Yes, the monitors are Plug-and-Play compatible with Windows® 95, 98, 2000, XP
and Vista.
LCD Panel Technology
Q: What is a Liquid Crystal Display?
A: A Liquid Crystal Display (LCD) is an optical device that is commonly used to
display ASCII characters and images on digital items such as watches, calculators,
portable game consoles, etc. LCD is the technology used for displays in notebooks
and other small computers. Like light-emitting diode and gas-plasma technologies,
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/safety/saf_faq.htm（第4／6页）2010-1-1111:53:04
FAQs(FrequentlyAskedQuestions)
LCD allows displays to be much thinner than cathode ray tube (CRT) technology.
LCD consumes much less power than LED and gas-displays because it works on the
principle of blocking light rather than emitting it.
Q: What differentiates passive matrix LCDs from active matrix LCDs?
A: An LCD is made with either a passive matrix or an active matrix display grid. An
active matrix has a transistor located at each pixel intersection, requiring less current
to control the luminance of a pixel. For this reason, the current in an active matrix
display can be switched on and off more frequently, improving the screen refresh time
(your mouse pointer will appear to move more smoothly across the screen, for
example). The passive matrix LCD has a grid of conductors with pixels located at
each intersection in the grid.
Q: What are the advantages of TFT LCD compared with CRT?
A: In a CRT monitor, a gun shoots electrons and general light by colliding polarized
electrons on fluorescent glass. Therefore, CRT monitors basically operate with an
analog RGB signal. A TFT LCD monitor is a device that displays an input image by
operating a liquid crystal panel. The TFT has a fundamentally different structure than
a CRT: Each cell has an active matrix structure and independent active elements. A
TFT LCD has two glass panels and the space between them is filled with liquid
crystal. When each cell is connected with electrodes and impressed with voltage, the
molecular structure of the liquid crystal is altered and controls the amount of inlet
lighting to display images. A TFT LCD has several advantages over a CRT, since it
can be very thin and no flickering occurs because it does not use the scanning
method.
Q: Why is vertical frequency of 60Hz optimal for an LCD monitor?
A: Unlike a CRT monitor, the TFT LCD panel has a fixed resolution. For example, an
XGA monitor has 1024x3 (R, G, B) x 768 pixels and a higher resolution may not be
available without additional software processing. The panel is designed to optimize
the display for a 65MHz dot clock, one of the standards for XGA displays. Since the
vertical/horizontal frequency for this dot clock is 60Hz/48kHz, the optimum frequency
for this monitor is 60Hz.
Q: What kind of wide-angle technology is available? How does it work?
A: The TFT LCD panel is an element that controls/displays the inlet of a backlight
using the dual-refraction of a liquid crystal. Using the property that the projection of
inlet light refracts toward the major axis of the liquid element, it controls the direction
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/safety/saf_faq.htm（第5／6页）2010-1-1111:53:04
FAQs(FrequentlyAskedQuestions)
of inlet light and displays it. Since the refraction ratio of inlet light on liquid crystal
varies with the inlet angle of the light, the viewing angle of a TFT is much narrower
than that of a CDT. Usually, the viewing angle refers to the point where the contrast
ration is 10. Many ways to widen the viewing angle are currently being developed and
the most common approach is to use a wide viewing angle film, which widens the
viewing angle by varying the refraction ratio. IPS (In Plane Switching) or MVA (Multi
Vertical Aligned) is also used to give a wider viewing angle.
Q: Why is there no flicker on an LCD Monitor?
A: Technically speaking, LCDs do flicker, but the cause of the phenomenon is
different from that of a CRT monitor -- and it has no impact of the ease of viewing.
Flickering in an LCD monitor relates to usually undetectable luminance caused by the
difference between positive and negative voltage. On the other hand, CRT flickering
that can irritate the human eye occurs when the on/off action of the fluorescent object
becomes visible. Since the reaction speed of liquid crystal in an LCD panel is much
slower, this troublesome form of flickering is not present in an LCD display.
Q: Why is an LCD monitor virtually low of Electro Magnetic Interference?
A: Unlike a CRT, an LCD monitor does not have key parts that generate Electro
Magnetic Interference, especially magnetic fields. Also, since an LCD display utilizes
relatively low power, its power supply is extremely quiet.
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/safety/saf_faq.htm（第6／6页）2010-1-1111:53:04
Troubleshooting
Troubleshooting
This page deals with problems that can be corrected by a user. If the problem still persists after you have tried these
solutions, contact Philips customer service representative.
Common Problems
Having this problem
Check these items
●
Make sure the power cord is plugged into the power outlet
and into the back of the monitor.
First, ensure that the power button on the front of the monitor
is in the OFF position, then press it to the ON position.
No Picture
(Power LED not lit)
●
●
●
Make sure the computer is turned on.
Make sure the VGA cable is properly connected to your
computer.
No Picture
●
●
Check to see if the monitor cable has bent pins.
The Energy Saving feature may be activated
(Power LED is amber or yellow)
Screen says
●
Make sure the monitor cable is properly connected to your
computer. (Also refer to the Quick Set-Up Guide).
Check to see if the monitor cable has bent pins.
Make sure the computer is turned on.
●
●
●
●
The Auto Function is designed for use on standard Macintosh
or IBM-compatible PCs running Microsoft Windows.
It may not work properly if using nonstandard PC or video
card.
AUTO button not working properly
Imaging Problems
●
●
Press the Auto button.
Adjust the image position using the Phase/Clock of More
Display position is incorrect
Image vibrates on the screen
Settings in OSD Main Controls.
●
Check that the VGA cable is properly connected to the
graphics board or PC.
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/safety/saf_troub.htm（第1／3页）2010-1-1111:53:08
Troubleshooting
Vertical flicker appears
●
●
Press the Auto button.
Eliminate the vertical bars using the Phase/Clock of More
Settings in OSD Main Controls.
Horizontal flicker appears
●
●
Press the Auto button.
Eliminate the vertical bars using the Phase/Clock of More
Settings in OSD Main Controls.
●
Adjust the contrast and brightness on On-Screen Display.
(The backlight of the LCD monitor has a fixed life span. When
the screen becomes dark or begins to flicker, please contact
your sales representative).
The screen is too bright or too dark
An after-image appears
●
●
●
If an image remains on the screen for an extended period of
time, it may be imprinted in the screen and leave an after-
image. This usually disappears after a few hours
This is characteristic of liquid crystal and is not caused by a
malfunction or deterioration of the liquid crystal. The after-
image will disappear after a peroid of time.
An after-image remains after the power
has been turned off.
The remaining dots are normal characteristic of the liquid
crystal used in today’s technology.
Green, red, blue, dark, and white dots
remains
For further assistance, refer to the Consumer Information Centers list and contact Philips customer service
representative.
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/safety/saf_troub.htm（第2／3页）2010-1-1111:53:08
Troubleshooting
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/safety/saf_troub.htm（第3／3页）2010-1-1111:53:08
RegulatoryInformation
Regulatory Information
Available for selective models
Recycling Information for Customers
There is currently a system of recycling up and running in the European countries, such as The
Netherlands, Belgium, Norway, Sweden and Denmark.
In Asia Pacific, Taiwan, the products can be taken back by Environment Protection Administration (EPA)
to follow the IT product recycling management process, detail can be found in web site www.epa.gov.tw
The monitor contains parts that could cause damage to the nature environment. Therefore, it is vital that the
monitor is recycled at the end of its life cycle.
For help and service, please contact Consumers Information Center or F1rst Choice Contact Information
Center in each country .
Waste Electrical and Electronic Equipment-WEEE
Attention users in European Union private households
This marking on the product or on its packaging illustrates that, under European Directive
2002/96/EG governing used electrical and electronic appliances, this product may not be disposed of
with normal household waste. You are responsible for disposal of this equipment through a designated
waste electrical and electronic equipment collection. To determine the locations for dropping off such
waste electrical and electronic, contact your local government office, the waste disposal organization that
serves your household or the store at which you purchased the product.
Energy Star Declaration
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/safety/regs/regulat.htm（第1／10页）2010-1-1111:53:13
RegulatoryInformation
This monitor is equipped with a function for saving energy which supports the VESA Display
Power Management (DPM) standard. This means that the monitor must be connected to a
computer which supports VESA DPM. Time settings are adjusted from the system unit by
software.
VESA State
ON (Active)
LED Indicator
Green
Power Consumption
< 14.5W (typ.)
Normal operation
Power Saving
Alternative 2
One step
OFF (Sleep)
Switch Off
Amber
Off
< 0.5 W
< 0.5 W
As an ENERGY STAR® Partner, we have determined that this product meets the
®
ENERGY STAR guidelines for energy efficiency.
We recommend you switch off the monitor when it is not in use for a long time.
Federal Communications Commission (FCC) Notice (U.S. Only)
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
●
●
●
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
●
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Use only RF shielded cable that was supplied with the monitor when connecting this monitor to a
computer device.
To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or
excessive moisture.
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/safety/regs/regulat.htm（第2／10页）2010-1-1111:53:13
RegulatoryInformation
THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN
INTERFERENCE-CAUSING EQUIPMENT REGULATIONS.
FCC Declaration of Conformity
Declaration of Conformity for Products Marked with FCC Logo,
United States Only
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
Commission Federale de la Communication (FCC Declaration)
Cet équipement a été testé et déclaré conforme auxlimites des appareils numériques de
class B,aux termes de l'article 15 Des règles de la FCC. Ces limites sont conçues de façon
à fourir une protection raisonnable contre les interférences nuisibles dans le cadre d'une
installation résidentielle. CET appareil produit, utilise et peut émettre des hyperfréquences
qui, si l'appareil n'est pas installé et utilisé selon les consignes données, peuvent causer
des interférences nuisibles aux communications radio. Cependant, rien ne peut garantir
l'absence d'interférences dans le cadre d'une installation particulière. Si cet appareil est la
cause d'interférences nuisibles pour la réception des signaux de radio ou de télévision, ce
qui peut être décelé en fermant l'équipement, puis en le remettant en fonction, l'utilisateur
pourrait essayer de corriger la situation en prenant les mesures suivantes:
●
●
●
●
Réorienter ou déplacer l'antenne de réception.
Augmenter la distance entre l'équipement et le récepteur.
Brancher l'équipement sur un autre circuit que celui utilisé par le récepteur.
Demander l'aide du marchand ou d'un technicien chevronné en radio/télévision.
Toutes modifications n'ayant pas reçu l'approbation des services compétents en matière de
conformité est susceptible d'interdire à l'utilisateur l'usage du présent équipement.
N'utiliser que des câbles RF armés pour les connections avec des ordinateurs ou périphériques.
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/safety/regs/regulat.htm（第3／10页）2010-1-1111:53:13
RegulatoryInformation
CET APPAREIL NUMERIQUE DE LA CLASSE B RESPECTE TOUTES LES EXIGENCES DU
REGLEMENT SUR LE MATERIEL BROUILLEUR DU CANADA.
EN 55022 Compliance (Czech Republic Only)
Polish Center for Testing and Certification Notice
The equipment should draw power from a socket with an attached protection circuit (a three-prong
socket). All equipment that works together (computer, monitor, printer, and so on) should have the same
power supply source.
The phasing conductor of the room's electrical installation should have a reserve short-circuit protection
device in the form of a fuse with a nominal value no larger than 16 amperes (A).
To completely switch off the equipment, the power supply cable must be removed from the power supply
socket, which should be located near the equipment and easily accessible.
A protection mark "B" confirms that the equipment is in compliance with the protection usage
requirements of standards PN-93/T-42107 and PN-89/E-06251.
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/safety/regs/regulat.htm（第4／10页）2010-1-1111:53:13
RegulatoryInformation
North Europe (Nordic Countries) Information
Placering/Ventilation
VARNING:
FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR
DU STÄLLER DIN UTRUSTNING PÅPLATS.
Placering/Ventilation
ADVARSEL:
SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT
ER NEMT TILGÆNGELIGE.
Paikka/Ilmankierto
VAROITUS:
SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI
IRROTTAA PISTORASIASTA.
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/safety/regs/regulat.htm（第5／10页）2010-1-1111:53:13
RegulatoryInformation
Plassering/Ventilasjon
ADVARSEL:
NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE FOR
STØMTILFØRSEL ER LETTE Å NÅ.
BSMI Notice (Taiwan Only)
Ergonomie Hinweis (nur Deutschland)
Der von uns gelieferte Farbmonitor entspricht den in der "Verordnung über den Schutz vor Schäden
durch Röntgenstrahlen" festgelegten Vorschriften.
Auf der Rückwand des Gerätes befindet sich ein Aufkleber, der auf die Unbedenklichkeit der
Inbetriebnahme hinweist, da die Vorschriften über die Bauart von Störstrahlern nach Anlage III ¤ 5 Abs.
4 der Röntgenverordnung erfüllt sind.
Damit Ihr Monitor immer den in der Zulassung geforderten Werten entspricht, ist darauf zu achten, daß
1. Reparaturen nur durch Fachpersonal durchgeführt werden.
2. nur original-Ersatzteile verwendet werden.
3. bei Ersatz der Bildröhre nur eine bauartgleiche eingebaut wird.
Aus ergonomischen Gründen wird empfohlen, die Grundfarben Blau und Rot nicht auf dunklem
Untergrund zu verwenden (schlechte Lesbarkeit und erhöhte Augenbelastung bei zu geringem
Zeichenkontrast wären die Folge).
Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 beträgt 70dB (A) oder weniger.
ACHTUNG: BEIM AUFSTELLEN DIESES GERÄTES DARAUF ACHTEN, DAß
NETZSTECKER UND NETZKABELANSCHLUß LEICHT ZUGÄNGLICH SIND.
End-of-Life Disposal
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/safety/regs/regulat.htm（第6／10页）2010-1-1111:53:13
RegulatoryInformation
Your new monitor contains materials that can be recycled and reused. Specialized companies can
recycle your product to increase the amount of reusable materials and to minimize the amount to be
disposed of.
Please find out about the local regulations on how to dispose of your old monitor from your local Philips
dealer.
Information for UK only
WARNING - THIS APPLIANCE MUST BE GROUNDING.
Important:
This apparatus is supplied with an approved moulded 13A
plug. To change a fuse in this type of plug proceed as
follows:
1. Remove fuse cover and fuse.
2. Fit new fuse which should be a BS 1362 5A,A.S.T.A. or
BSI approved type.
3. Refit the fuse cover.
If the fitted plug is not suitable for your socket outlets, it
should be cut off and an appropriate 3-pin plug fitted in its
place.
If the mains plug contains a fuse, this should have a value
of 5A. If a plug without a fuse is used, the fuse at the
distribution board should not be greater than 5A.
Note: The severed plug must be destroyed to avoid a
possible shock hazard should it be inserted into a 13A
socket elsewhere.
How to connect a plug
The wires in the mains lead are coloured in accordance
with the following code:
BLUE - "NEUTRAL" ("N")
BROWN - "LIVE" ("L")
GREEN & YELLOW - "GROUND" ("G")
1. The GREEN AND YELLOW wire must be connected to
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/safety/regs/regulat.htm（第7／10页）2010-1-1111:53:13
RegulatoryInformation
the terminal in the plug which is marked with the letter "G"
or by the Ground symbol
AND YELLOW.
or coloured GREEN or GREEN
2. The BLUE wire must be connected to the terminal which
is marked with the letter "N" or coloured BLACK.
3. The BROWN wire must be connected to the terminal
which marked with the letter "L" or coloured RED.
Before replacing the plug cover, make certain that the cord
grip is clamped over the sheath of the lead - not simply
over the three wires.
China RoHS
The People's Republic of China released a regulation called "Management Methods for Controlling
Pollution by Electronic Information Products" or commonly referred to as China RoHS. All products
including CRT and LCD monitor which are produced and sold for China market have to meet China
RoHS request.
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/safety/regs/regulat.htm（第8／10页）2010-1-1111:53:13
RegulatoryInformation
Lead free display promotes environmentally sound recovery and disposal of waste from
electrical and electronic equipment. Toxic substances like Lead has been eliminated and
compliance with European community’s stringent RoHs directive mandating restrictions on
hazardous substances in electrical and electronic equipment have been adhered to in
order to make Philips monitors safe to use throughout its life cycle.
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/safety/regs/regulat.htm（第10／10页）2010-1-1111:53:13
OtherRelatedInformation
Other Related Information
Information for Users in the U. S.
For units set at 115 V :
Use a UL Listed Cord Set consisting of a minimum 18 AWG, Type SVT or SJT three conductor cord
a maximum of 15-feet long and a parallel blade, grounding type attachment plug rated 15 A, 125 V.
For units set at 230 V:
Use a UL Listed Cord Set consisting of a minimum 18 AWG, Type SVT or SJT three conductor cord
a maximum of 15-feet long and a tandem blade, grounding type attachment plug rated 15 A, 250 V.
Information for Users outside the U.S.
For units set at 230 V:
Use a Cord Set consisting of a minimum 18 AWG cord and grounding type attachment plug rated
15 A, 250 V. The Cord Set should have the appropriate safety approvals for the country in which
the equipment will be installed and / or be marked HAR.
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/safety/saf_other.htm2010-1-1111:53:16
AboutThisM anual
About This Manual
About This Guide
This electronic user's guide is intended for anyone who uses the Philips LCD Monitor. It
describes the LCD monitor's features, setup, operation and other important information. Its
contents are identical to the information in our printed version.
It includes the following sections:
●
Safety and Troubleshooting Information provides tips and solutions for common problems
as well as other related information you may need.
●
●
About This Electronic User's Manual gives an overview of information included, along with
notation icon descriptions and other documentation for your reference.
Product Information gives an overview of the monitor's features as well as the technical
specifications for this monitor.
●
Installing Your Monitor describes the initial setup process and gives an overview of how to
use the monitor.
●
●
On-Screen Display provides information on adjusting the settings on your monitor.
Customer Care and Warranty contains a list of worldwide Philips Consumer Information
Centers along with help desk phone numbers and information on the warranty applicable
to your product.
●
Download and Print Option transfers this entire manual to your hard drive for easy
reference.
Notational Descriptions
The following subsections describe notational conventions used in this document.
Notes, Cautions and Warnings
Throughout this guide, blocks of text may be accompanied by an icon and printed in bold or italic
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/about/about.htm（第1／2页）2010-1-1111:53:19
AboutThisM anual
type. These blocks contain notes, cautions or warnings. They are used as follows:
NOTE: This icon indicates important information and tips that help you make
better use of your computer system.
CAUTION: This icon indicates information that tells you how to avoid either
potential damage to hardware or loss of data.
WARNING: This icon indicates the potential for bodily harm and tells you how
to avoid the problem.
Some warnings may appear in alternate formats and may not be accompanied by an icon. In
such cases, the specific presentation of the warning is mandated by the relevant regulatory
authority.
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/about/about.htm（第2／2页）2010-1-1111:53:19
ProductInformation
Product Information
Technical Specifications*
LCD PANEL
• Type
TFT LCD
• Screen size
• Pixel Pitch
15.6" visual
0.252 x 0.252 mm
1366 x 768 pixels
R.G.B. vertical stripe
• LCD Panel type
Anti-glare polarizer, hard coated
• Effective viewing area
• Display Colors
347.5 x 196.8 mm
16.7m
SCANNING
• Vertical refresh rate
• Horizontal Frequency
56 Hz-76 Hz
30 kHz - 83 kHz
VIDEO
• Video dot rate
140 MHz
• Input impedance
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/product/product.htm（第1／6页）2010-1-1111:53:22
ProductInformation
- Video
- Sync
75 ohm
2.2K ohm
0.7 Vpp
• Input signal levels
• Sync input signal
• Sync polarities
Separate sync
Composite sync
Sync on green
Positive and negative
* This data is subject to change without notice.
Resolution & Preset Modes
A.
-
Maximum Resolution
For 160EL1
1366x768 at 75Hz(analog input)
1366x768 at 75Hz(digital input)
Recommended Resolution
For 160EL1
B.
-
1366x768 at 60Hz(analog input)
1366x768 at 60Hz(digital input)
10 factory preset modes:
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/product/product.htm（第2／6页）2010-1-1111:53:22
ProductInformation
H. freq (kHz)
31.47
Resolution
720*400
V. freq (Hz)
70.09
59.94
75.00
60.32
75.00
60.00
75.03
60.02
75.03
59.79
31.47
640*480
37.50
640*480
37.88
800*600
46.88
800*600
48.36
1024*768
1024*768
1280*1024
1280*1024
1366*768
60.02
63.89
79.98
47.71
Automatic Power Saving
If you have VESA DPM compliance display card or software installed in your PC, the monitor can automatically reduce
its power consumption when not in use. If an input from a keyboard, mouse or other input device is detected, the
monitor will 'wake up' automatically. The following table shows the power consumption and signaling of this automatic
power saving feature:
Power Management Definition
LED
color
VESA Mode
Video
H-sync
V-sync
Power Used
Active
Sleep
ON
OFF
OFF
Yes
No
-
Yes
No
-
< 14.5 W (typ.)
< 0.5 W
Green
Amber
Off
Switch Off
< 0.5 W
®
®
This monitor is ENERGY STAR compliant. As an ENERGY STAR Partner, we have
®
determined that this product meets the ENERGY STAR guidelines for energy efficiency.
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/product/product.htm（第3／6页）2010-1-1111:53:22
ProductInformation
Physical Specifications
• Tilt
-5° ~ 20°
• Power supply
• Power consumption
100 ~ 240 VAC, 50/60 Hz
<14.5 W* (typ.)
0° C to 40° C (operating)
-20° C to 60° C (storage)
• Temperature
• Relative humidity
• System MTBF
20% to 80%
50K hours (CCFL 50K hours)
• Cabinet color
160EL1SB: Black
Pin Assignment
The 15-pin D-sub connector (male) of the signal cable:
Pin No. Assignment
Pin No.
9
Assignment
Red video input
DDC + 5 V
1
2
3
4
5
6
7
Green video input/SOG
Blue video input
Logic ground
10
Ground
11
Sense (GND)
Serial data line (SDA)
H. Sync / H+V. Sync
V. Sync
12
Cable detect (GND)
Red video ground
Green video ground
13
14
Data clock line (SCL)
15
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/product/product.htm（第4／6页）2010-1-1111:53:22
ProductInformation
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/product/product.htm（第6／6页）2010-1-1111:53:22
PhilipsPixelDefectPolicy
Philips Pixel Defect Policy
Philips' Flat Panel Monitors Pixel Defect Policy
Philips strives to deliver the highest quality products. We use some of the industry's most advanced
manufacturing processes and practice stringent quality control. However, pixel or sub pixel defects on the
TFT LCD panels used in flat panel monitors are sometimes unavoidable. No manufacturer can guarantee
that all panels will be free from pixel defects, but Philips guarantees that any monitor with an unacceptable
number of defects will be repaired or replaced under warranty. This notice explains the different types of
pixel defects and defines acceptable defect levels for each type. In order to qualify for repair or replacement
under warranty, the number of pixel defects on a TFT LCD panel must exceed these acceptable levels. For
example, no more than 0.0004% of the sub pixels on a 19" XGA monitor may be defective. Furthermore,
Philips sets even higher quality standards for certain types or combinations of pixel defects that are more
noticeable than others. This policy is valid worldwide.
Pixels and Sub pixels
A pixel, or picture element, is composed of three sub pixels in the primary colors of red, green and blue.
Many pixels together form an image. When all sub pixels of a pixel are lit, the three colored sub pixels
together appear as a single white pixel. When all are dark, the three colored sub pixels together appear as a
single black pixel. Other combinations of lit and dark sub pixels appear as single pixels of other colors.
Types of Pixel Defects
Pixel and sub pixel defects appear on the screen in different ways. There are two categories of pixel defects
and several types of sub pixel defects within each category.
Bright Dot Defects Bright dot defects appear as pixels or sub pixels that are always lit or 'on'. That is, a
bright dot is a sub-pixel that stands out on the screen when the monitor displays a dark pattern. There are
three types of bright dot defects:
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/product/pixel.htm（第1／3页）2010-1-1111:53:25
PhilipsPixelDefectPolicy
Two adjacent lit sub pixels:
- Red + Blue = Purple
- Red + Green = Yellow
One lit red, green or blue sub
pixel
Three adjacent lit sub pixels
(one white pixel)
- Green + Blue = Cyan (Light Blue)
A red or blue bright dot must be more than 50 percent brighter than neighboring dots while a
green bright dot is 30 percent brighter than neighboring dots.
Black Dot Defects Black dot defects appear as pixels or sub pixels that are always dark or 'off'. That is, a
dark dot is a sub-pixel that stands out on the screen when the monitor displays a light pattern. There are two
types of black dot defects:
One dark sub pixel
Two or three adjacent dark sub pixels
Proximity of Pixel Defects
Because pixel and sub pixels defects of the same type that are near to one another may be more
noticeable, Philips also specifies tolerances for the proximity of pixel defects.
Pixel Defect Tolerances
In order to qualify for repair or replacement due to pixel defects during the warranty period, a TFT LCD
panel in a Philips flat panel monitor must have pixel or sub pixel defects exceeding the tolerances listed in
the following tables.
BRIGHT DOT DEFECTS
ACCEPTABLE LEVEL
160EL1
MODEL
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/product/pixel.htm（第2／3页）2010-1-1111:53:26
PhilipsPixelDefectPolicy
1 lit subpixel
3
2 adjacent lit subpixels
1
3 adjacent lit subpixels (one white pixel)
Distance between two bright dot defects*
Total bright dot defects of all types
0
>15mm
3
BLACK DOT DEFECTS
MODEL
ACCEPTABLE LEVEL
160EL1
1 dark subpixel
5
2 adjacent dark subpixels
3 adjacent dark subpixels
Distance between two black dot defects*
Total black dot defects of all types
2
0
>15mm
5
TOTAL DOT DEFECTS
MODEL
ACCEPTABLE LEVEL
160EL1
Total bright or black dot defects of all types
5
Note:
* 1 or 2 adjacent sub pixel defects = 1 dot defect
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/product/pixel.htm（第3／3页）2010-1-1111:53:26
InstallingYourLCD M onitor
Installing Your LCD Monitor
Front View Product Description
1
To switch monitor's power On and Off
MENU / OK To access OSD menu/ Confirm
2
3
4
5
/
/
To adjust brightness of the display
auto picure control switching in wide and 4:3 format.
Automatically adjust the horizontal position, vertical position, phase and
clock settings.
AUTO /
Return to previous OSD level.
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/install/install.htm（第1／3页）2010-1-1111:53:31
InstallingYourLCD M onitor
Rear View
1
2
3
Kensington anti-thief lock
AC power input
VGA input
Optimizing Performance
●
For best performance, ensure that your display settings are set at 1366 x 768, 60Hz.
Note: You can check the current display settings by pressing the 'MENU' button once. The
current display mode is shown in OSD main controls called RESOLUTION.
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/install/install.htm（第2／3页）2010-1-1111:53:31
InstallingYourLCD M onitor
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/install/install.htm（第3／3页）2010-1-1111:53:31
ConnectingtoYourPC
Connecting to Your PC
1) Connect the power cord to the back of the monitor firmly.
2) Connect to PC
(a)
(b)
Turn off your computer and unplug its power cable.
Connect the monitor signal cable to the video connector on the back of your
computer.
(c)
Plug the power cord of your computer and your monitor into a nearby outlet.
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/install/connect.htm（第2／3页）2010-1-1111:53:33
ConnectingtoYourPC
(d)
Turn on your computer and monitor. If the monitor displays an image,
installation is complete.
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/install/connect.htm（第3／3页）2010-1-1111:53:33
TheBase
The Base
Remove the Base
Condition:
●
for VESA standard mounting applications
Remove the 3 screws and then remove the base from the LCD monitor.
Note: This monitor accepts a 100 mmx100 mm VESA-Compliant mounting interface.
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/install/base.htm（第1／2页）2010-1-1111:53:36
TheBase
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/install/base.htm（第2／2页）2010-1-1111:53:36
GettingStarted
Your LCD Monitor :
Getting Started
Getting Started
Use the information file ( .inf) for Windows® 95/98/2000/Me/XP/Vista or later
The built-in VESA DDC2B feature in Philips Monitors supports Plug & Play requirements for
Windows® 95/98/2000/Me/XP/Vista. This information file ( .inf) should be installed in order that
your Philips monitor can be enabled from the 'Monitor' dialog box in Windows® 95/98/2000/Me/
XP/Vista and the Plug & Play application can be activated. The installation procedure based on
Windows® 95 OEM Release 2 , 98 , 2000 , Me, XP and Vista is specified as follows.
For Windows® 95
1. Start Windows® 95
2. Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'.
3. Double click on the 'Display' Icon.
4. Select the 'Settings' tab then click on 'Advanced...'.
5. Select the 'Monitor' button, point to 'Change...' then click on 'Have Disk...'.
6. Click on the 'Browse...' button, select the appropriate drive F: ( CD-ROM Drive) then click
on the 'OK' button.
7. Click on the 'OK' button then select your monitor model and click on 'OK'.
8. Click on the 'Close' button.
For Windows® 98
1. Start Windows® 98
2. Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'.
3. Double click on the 'Display' Icon.
4. Select the 'Settings' tab then click on 'Advanced...'.
5. Select the 'Monitor' button, point to 'Change...' then click on 'Next'
6. Select 'Display a list of all the drivers in a specific location, so you can choose the driver
you want.' then click on 'Next' and then click on 'Have Disk...'.
7. Click on the 'Browse...' button, select the appropriate drive F: ( CD-ROM Drive) then click
on the 'OK' button.
8. Click on the 'OK' button then select your monitor model and click on the 'Next' button.
9. Click on the 'Finish' button then the 'Close' button.
For Windows® 2000
1. Start Windows® 2000
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/install/gt_start.htm（第1／3页）2010-1-1111:53:40
GettingStarted
2. Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'.
3. Double click on the 'Display' Icon.
4. Select the 'Settings' tab then click on 'Advanced...'.
5. Select 'Monitor'
- If the 'Properties' button is inactive, it means your monitor is properly configured. Please
stop installation.
- If the 'Properties' button is active. Click on 'Properties' button. Please follow the steps
given below.
6. Click on 'Driver' and then click on 'Update Driver...' then click on the 'Next' button.
7. Select 'Display a list of the known drivers for this device so that I can choose a specific
driver', then click on 'Next' and then click on 'Have disk...'.
8. Click on the 'Browse...' button then select the appropriate drive F: ( CD-ROM Drive).
9. Click on the 'Open' button, then click on the 'OK' button.
10. Select your monitor model and click on the 'Next' button.
11. Click on the 'Finish' button then the 'Close' button.
If you can see the 'Digital Signature Not Found' window, click on the 'Yes' button.
For Windows® Me
1. Start Windows® Me
2. Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'.
3. Double click on the 'Display' Icon.
4. Select the 'Settings' tab then click on 'Advanced...'.
5. Select the 'Monitor' button, then click on 'Change...' button.
6. Select 'Specify the location of the driver(Advanced)' and click on the 'Next' button.
7. Select 'Display a list of all the drivers in a specific location, so you can choose the driver
you want', then click on 'Next' and then click on 'Have Disk...'.
8. Click on the 'Browse...' button, select the appropriate drive F: ( CD-ROM Drive) then click
on the 'OK' button.
9. Click on the 'OK' button, select your monitor model and click on the 'Next' button.
10. Click on 'Finish' button then the 'Close' button.
For Windows® XP
1. Start Windows® XP
2. Click on the 'Start' button and then click on 'Control Panel'.
3. Select and click on the category 'Printers and Other Hardware'
4. Click on the 'Display' Item.
5. Select the 'Settings' tab then click on the 'Advanced' button.
6. Select 'Monitor' tab
- If the 'Properties' button is inactive, it means your monitor is properly configured. Please
stop installation.
- If the 'Properties' button is active, click on 'Properties' button.
Please follow the steps below.
7. Click on the 'Driver' tab and then click on 'Update Driver...' button.
8. Select the 'Install from a list or specific location [advanced]' radio button and then click on
the 'Next' button.
9. Select the 'Don't Search. I will choose the driver to install' radio button. Then click on the
'Next' button.
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/install/gt_start.htm（第2／3页）2010-1-1111:53:40
GettingStarted
10. Click on the 'Have disk...' button, then click on the 'Browse...' button and then select the
appropriate drive F: (CD-ROM Drive).
11. Click on the 'Open' button, then click the 'OK' button.
12. Select your monitor model and click on the 'Next' button.
- If you can see the 'has not passed Windows® Logo testing to verify its compatibility with
Windows® XP' message, please click on the 'Continue Anyway' button.
13. Click on the 'Finish' button then the 'Close' button.
14. Click on the 'OK' button and then the 'OK' button again to close the Display_Properties
dialog box.
For Windows® Vista
1. Start Windows® Vista
2. Click the Start button; select and click on 'Control Panel'.
3. Select and click on 'Hardware and Sound'
4. Choose 'Device Manager' and Click on 'Update device drivers'.
5. Select 'Monitor' and then right click on 'Generic PnP Monitor'.
6. Click on 'Update Driver Software'.
7. Select 'Browse my computer for driver software'.
8. Click the 'Browse'button and choose the drive in which you've placed the disk. Example:
(CD-ROM Drive:\\Lcd\PC\drivers\).
9. Click the 'Next' button.
10. Wait few minutes for installing the driver, and then click 'Close' button.
If your Windows® 95/98/2000/Me/XP/Vista version is different or you need more detailed
installation information, please refer to your Windows® 95/98/2000/Me/XP/Vista user's manual.
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/install/gt_start.htm（第3／3页）2010-1-1111:53:40
On-ScreenDisplay
On-Screen Display
Description of the On Screen Display
What is the On-Screen Display?
This is a feature in all Philips LCD monitors. It allows an end user to adjust screen performance of
the monitors directly through an on-screen instruction window. The user interface provides user-
friendliness and ease-of-use when operating the monitor.
Basic and simple instruction on the control keys.
When you press the MENU/OK button on the front control of your monitor, the On-Screen Display
(OSD) Main Controls window will pop up and you can then start making adjustments to your
monitor's various features. Use the
keys to make your adjustments.
*PC Audio input (available for selective models)
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/osd/osddesc.htm（第1／3页）2010-1-1111:53:48
On-ScreenDisplay
The OSD Tree
Below is an overall view of the structure of the On-Screen Display. You can use this as a reference
when you want to work your way around the different adjustments later on.
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/osd/osddesc.htm（第2／3页）2010-1-1111:53:48
On-ScreenDisplay
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/osd/osddesc.htm（第3／3页）2010-1-1111:53:48
CustomerCare& W arranty
Customer Care & Warranty
PLEASE SELECT YOUR COUNTRY/AREA TO REVIEW DETAILS OF YOUR
WARRANTY COVERAGE
AFRICA: South Africa
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/warranty/warranty.htm2010-1-1111:53:50
YourPhilipsF1rstChoiceW arranty
Your Philips F1rst Choice Warranty
Thank you for purchasing this Philips monitor.
All Philips monitors are designed and manufactured to high standards and deliver
high-quality performance, ease of use and ease of installation. Should you
encounter any difficulties while installing or using this product, please contact the
Philips helpdesk directly to benefit from your Philips F1rst Choice Warranty. This
three-year service warranty entitles you to a swap model on-site if your monitor
turns out to be faulty or defective. Philips aims at a swap within 48 hours of your
call being received.
What is covered?
The Philips F1rst Choice Warranty applies within Andorra, Austria, Belgium, Cyprus, Denmark,
France, Germany, Greece, Finland, Ireland, Italy, Liechtenstein, Luxembourg, Monaco, the
Netherlands, Norway, Poland, Portugal, Sweden, Switzerland, Spain and the United Kingdom and
only for monitors originally designed, manufactured, approved and/or authorized for usage within
these countries.
Warranty coverage begins as from the day you buy your monitor. For three years thereafter, your
monitor will be swapped by at least an equivalent monitor in case of defects provided for under the
warranty coverage.
The swap monitor remains yours and Philips keeps the defective/original monitor. For the swap
monitor the warranty period remains equal to that of your original monitor, being 36 months as from
the purchase date of your original monitor.
What is excluded?
The Philips F1rst Choice Warranty applies provided the product is handled properly for its intended
use, in accordance with its operating instructions and upon presentation of the original invoice or
cash receipt, indicating the date of purchase, dealer's name and model and production number of
the product.
The Philips F1rst Choice Warranty may not apply if:
●
●
The documents have been altered in any way or made illegible;
The model or production number on the product has been altered, deleted, removed or made
illegible;
●
●
Repairs or product modifications and alterations have been executed by unauthorized service
organizations or persons;
Damage is caused by accidents including but not limited to lightning, water or fire, misuse or
neglect;
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/warranty/war_1st.htm（第1／3页）2010-1-1111:53:53
YourPhilipsF1rstChoiceW arranty
●
Reception problems caused by signal conditions or cable or antenna systems outside the
unit;
●
●
Defects caused by abuse or misuse of the monitor;
Product requires modification or adaptation to enable it to comply with local or national
technical standards, which apply in countries for which the product was not originally
designed, manufactured, approved and/or authorized. Therefore always check whether a
product can be used in a specific country.
●
Note that products that are not originally designed, manufactured, approved and/or
authorized for usage within the Philips F1rst Choice countries, do not apply to the Philips
F1rst Choice Warranty. In these cases the Philips global warranty terms are valid.
Just a click away
In case of any problems, we advise you to read the operating instructions carefully or go to the www.
philips.com/support website for additional support.
Just a phone call away
In order to avoid unnecessary inconvenience, we advise you to read the operating instructions
Philips helpdesk.
To solve your problem quickly, please prepare the following details before contacting the Philips
helpdesk:
●
●
●
●
Philips type number
Philips serial number
Purchase date (copy of purchase may be required)
PC environment Processor:
❍
❍
❍
CUP and Graphic card name and driver version
Operating system
Application being used
●
Other cards installed
Having the following information available will also help speed up the process:
●
●
Your proof of purchase indicating: date of purchase, dealer name, model and product serial
number.
The full address to which the faulty monitor has to be collected and the swap model should
be delivered.
Or you can reach us via:
Website: http://www.philips.com/support
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/warranty/war_1st.htm（第2／3页）2010-1-1111:53:53
YourPhilipsF1rstChoiceW arranty
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/warranty/war_1st.htm（第3／3页）2010-1-1111:53:53
F1rstChoiceContactInformation
F1rst Choice Contact Information
Country
Code
+43
+32
+45
+358
+33
+49
+30
+353
+39
+352
+31
+47
+48
+351
+34
+46
+41
+44
Telephone number
0810 000206
078 250851
Tariff
Austria
€0.07
Belgium
Denmark
Finland
€0.06
3525 8761
Local call tariff
Local call tariff
€0.09
09 2290 1908
082161 1658
01803 386 853
00800 3122 1223
01 601 1161
840 320 041
26 84 30 00
France
Germany
Greece
€0.09
Free of charge
Local call tariff
€0.08
Ireland
Italy
Luxembourg
The Netherlands
Norway
Local call tariff
€0.10
0900 0400 063
2270 8250
Local call tariff
Local call tariff
Local call tariff
€0.10
Poland
0223491505
2 1359 1440
902 888 785
08 632 0016
02 2310 2116
0207 949 0069
Portugal
Spain
Sweden
Switzerland
United Kingdom
Local call tariff
Local call tariff
Local call tariff
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/warranty/warfirst.htm2010-1-1111:53:54
YourGuaranteeinCentralandEasternEurope
Your Guarantee in Central and Eastern Europe
Dear Customer,
Thank you for purchasing this Philips product, which has been designed and manufactured to the
highest quality standards. If, unfortunately, something should go wrong with this product Philips
guarantees free of charge labor and replacement parts during a period of 36 months from date of
purchase.
What is covered?
This Philips Guarantee in Central and Eastern Europe applies within Czech Republic, Hungary,
Slovakia, Slovenia, Russia and Turkey and only for monitors originally designed, manufactured,
approved and/or authorized for usage within these countries.
Warranty coverage begins as from the day you buy your monitor. For 3 years thereafter, your
monitor will be serviced in case of defects provided for under the warranty coverage.
What is excluded?
The Philips guarantee applies provided the product is handled properly for its intended use, in
accordance with its operating instructions and upon presentation of the original invoice or cash
receipt, indicating the date of purchase, dealer's name and model and production number of the
product.
The Philips guarantee may not apply if:
●
●
the documents have been altered in any way or made illegible;
the model or production number on the product has been altered, deleted, removed or made
illegible;
●
●
●
repairs or product modifications and alterations have been executed by unauthorized service
organizations or persons;
damage is caused by accidents including but not limited to lightning, water or fire, misuse or
neglect.
Reception problems caused by signal conditions or cable or antenna systems outside the
unit;
●
●
Defects caused by abuse or misuse of the monitor;
Product requires modification or adaptation to enable it to comply with local or national
technical standards, which apply in countries for which the product was not originally
designed, manufactured, approved and/or authorized. Therefore always check whether a
product can be used in a specific country.
Please note that the product is not defective under this guarantee in the case where modifications
become necessary in order for the product to comply with local or national technical standards
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/warranty/war_ee.htm（第1／2页）2010-1-1111:53:58
YourGuaranteeinCentralandEasternEurope
which apply in countries for which the product was not originally designed and/or manufactured.
Therefore always check whether a product can be used in a specific country.
Just a click away
In case of any problems, we advise you to read the operating instructions carefully or go to the www.
philips.com/support website for additional support.
Just a phone call away
In order to avoid unnecessary inconvenience, we advise you to read the operating instructions
carefully before contacting our dealers or Information Centers
In case your Philips product is not working correctly or is defective, please contact your Philips
dealer or directly the Philips Service and Consumer Information Centers
Website: http://www.philips.com/support
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/warranty/war_ee.htm（第2／2页）2010-1-1111:53:58
ConsumerInformationCenters
Consumer Information Centers
Eastern Europe
BELARUS
Technic al Center of JV IBA
M. Bogdanovich str. 155
BY - 220040 Minsk
Tel: +375 17 217 33 86
BELARUS
Service.BY
Petrus Brovky st. 19 – 101-B
220072, Minsk
Belarus
BULGARIA
LAN Service
140, Mimi Balkanska Str.
Office center Translog
1540 Sofia, Bulgaria
Tel: +359 2 960 2360
CZECH REPUBLIC
General Consumer Information Center
800 142100
Xpectrum
Lu.ná 591/4
CZ - 160 00 Praha 6 Tel: 800 100 697 or 220 121 435
Email:[email protected]
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/warranty/warcic.htm（第1／9页）2010-1-1111:54:01
ConsumerInformationCenters
CROATIA
Renoprom d.o.o.
Ljubljanska 4,
Sv. Nedjelja,10431
Croatia
Tel: +385 1 333 0974
ESTONIA
FUJITSU SERVICES OU
Akadeemia tee 21G
EE-12618 Tallinn
Tel: +372 6519900
HUNGARY
Serware Szerviz
Vizimolnár u. 2-4
HU - 1031 Budapest
Tel: +36 1 2426331
Email: [email protected]
HUNGARY
Profi Service Center Ltd.
123 Kulso-Vaci Street,
H-1044 Budapest ( Europe Center )
Hungary
Tel: +36 1 814 8080
LATVIA
ServiceNet LV
Jelgavas iela 36
LV - 1055 Riga,
Tel: +371 7460399
Email: [email protected]
LITHUANIA
ServiceNet LT
Gaiziunu G. 3
LT - 3009 KAUNAS
Tel: +370 7400088
Email: [email protected]
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/warranty/warcic.htm（第2／9页）2010-1-1111:54:01
ConsumerInformationCenters
ROMANIA
Blue Ridge Int'l Computers SRL
115, Mihai Eminescu St., Sector 2
RO - 020074 Bucharest
Tel: +40 21 2101969
SERBIA & MONTENEGRO
Kim Tec d.o.o.
Viline vode bb, Slobodna zona
Beograd L12/3
11000 Belgrade
Serbia
Tel. +381 11 20 70 684
SLOVAKIA
General Consumer Information Center
0800004551
Datalan Servisne Stredisko
Puchovska 8
SK - 831 06 Bratislava
Tel: +421 2 49207155
Email: [email protected]
SLOVENIA
PC HAND
Brezovce 10
SI - 1236 Trzin
Tel: +386 1 530 08 24
Email: [email protected]
RUSSIA
CPS
18, Shelepihinskaya nab.
123290 Moscow
Russia
Tel. +7(495)797 3434
Profservice:
14A -3, 2Karacharovskaya str,
109202, Moscow ,
Russia
Tel. +7(095)170-5401
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/warranty/warcic.htm（第3／9页）2010-1-1111:54:01
ConsumerInformationCenters
TURKEY
Türk Philips Ticaret A.S.
Yukari Dudullu Org.San.Bolgesi
2.Cadde No:22
34776-Umraniye/Istanbul
Tel: (0800)-261 33 02
UKRAINE
Comel
Shevchenko street 32
UA - 49030 Dnepropetrovsk
Tel: +380 562320045
LLC Topaz Company
Topaz-Service Company,
Mishina str. 3,
Kiev
Ukraine-03151
Tel: +38 044 245 73 31
Latin America
ARGENTINA
Azopardo 1480.
(C1107ADZ) Cdad. de Buenos Aires
Tel: 0800 3330 856
Email: [email protected]
BRASIL
Alameda Raja Gabaglia, 188 - 10°Andar - V.
Olímpia - S. Paulo/SP - CEP 04551-090 -
Brasil
Tel: 0800-7254101
Email: [email protected]
Pacific
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/warranty/warcic.htm（第4／9页）2010-1-1111:54:01
ConsumerInformationCenters
AUSTRALIA
Company: AGOS NETWORK PTY LTD
Address: 4/5 Dursley Road, Yenorra, NSW 2161, Australia
Tel: 1300 360 386
Fax: +61-2-80808147
Email: [email protected]
Service hours: Mon.~Fri. 8:00am-7:30pm
NEW ZEALAND
Company: Visual Group Ltd.
Address: 28 Walls Rd Penrose Auckland
Phone: 0800 657447
Fax: 09 5809607
E-mail: [email protected]
Service Hours: Mon.~Fri. 8:30am~5:30pm
Asia
HONG KONG/Macau
Company Name: PHK Service Limited
Address: Flat A, 10/F., Pak Sun Building, 103 - 107 Wo Yi Hop Road, Kwai Chung, New Territories, Hong
Kong
Tel.: (852) 2610-6908 / (852) 2610-6929 for Hong Kong and (853) 2856-2277 for Macau
Fax: (852) 2485 3574 for Hong Kong and (853) 2856 1498 for Macau
E-mail: [email protected]
Service Hours: Mon.~Sat. 09:00am~06:00pm
India
Company: REDINGTON INDIA LTD
Address: SPL Guindy House, 95 Mount Road, Chennai 600032, India
Tel: +9144-42243352/353
E-mail: [email protected]
Service hours: Mon.~Fri. 9:00AM~5:30PM; Sat. 9:00AM~1:00PM
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/warranty/warcic.htm（第5／9页）2010-1-1111:54:01
ConsumerInformationCenters
Indonesia
Company Name: PT. Gadingsari elektronika Prima
Address: Kompleks Pinang 8, Jl. Ciputat raya No. 8F, Pondok Pinang. Jakarta
Tel: 021-750909053, 021-750909056
Fax: 021-7510982
E-mail: [email protected]
Service hours: Mon.~Fri. 8:30am~4:30pm; Sat. 8:30am~2:00pm
Additional service points:
1. Philips Building Jl. Buncit Raya Kav 99. Jakarta Selatan.
Phone: 021-7940040, ext 1722/1724, 98249295, 70980942
2. Jl. Tanah Abang 1 no 12S. Jakarta Pusat.
Phone: 021-3455150, 34835453
3. Rukan City Home no H31, Gading Square. Jl. Bulevar Barat. Kelapa Gading. Jakarta Utara. Phone: 021-
45870601, 98131424
South Korea
Company: PCS One Korea Ltd.
Address: 112-2, Banpo-dong, Seocho-ku, Seoul, 137-040, Korea
Call Center Tel: 080-600-6600
Tel: 82 2 591 1528
Fax: 82 2 595 9688
E-mail: [email protected]
Service hours: Mon.~Fri. 9:00AM~ 6:00PM; Sat. 9:00AM~1:00PM
Malaysia
Company: After Market Solutions (CE) Sdn Bhd
Address: Lot 6. Jalan 225/51A, 46100 Petaling Jaya, Selangor DE, Malaysia.
Phone: 603 7953 3370
Philips Info Line: 1-800-880-180
Fax: 603 7953 3338
E-mail: [email protected]
Service Hours: Mon.~Fri. 8:15am~5:15pm; Sat. 9:00am~1:00pm
Pakistan
Philips Consumer Service
Address: Mubarak manzil, 39, Garden Road, Saddar, Karachi-74400
Tel: (9221) 2737411-16
Fax: (9221) 2721167
E-mail: [email protected]
Website: www.philips.com.p
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/warranty/warcic.htm（第6／9页）2010-1-1111:54:01
ConsumerInformationCenters
Singapore
Company: Philips Electronics Singapore Pte Ltd (Philips Consumer Care Center)
Address: 620A Lorong 1 Toa Payoh, TP4 Building Level 1, Singapore 319762
Tel: (65) 6882 3999
Fax: (65) 62508037
E-mail: [email protected]
Service hours: Mon.~Fri. 9:00am~6:00pm; Sat. 9:00am~1:00pm
Taiwan
Company: FETEC.CO
Address: 3F, No.6, Lane 205, Sec. 1, Chang Hsing Rd, Lu Chu Hs, Taoyuan, Taiwan R.O.C 33800
Consumer Care: 0800-231-099
Tel: (03)2120336
Fax: (03)3129184
E-mail: [email protected]
Service hours: Mon.~Fri. 8:30am~7:00pm
Thailand
Company: Axis Computer System Co., Ltd.
Address: 1421 Soi Lardprao 94, Srivara Town In Town Soi 3 Road, Wangthonglang, Bangkok 10310
Thailand
Tel: (662) 934-5498
Fax: (662) 934-5499
E-mail: [email protected]
Service Hours: Mon.~Fri. 08:30am~05:30pm
Vietnam
Company: Digiworld Corp
Address: 211-213 Vo Van Tan St, Ward 5, Dist.3 , Ho Chi Minh city, Vietnam
Tel: 848-38266065
Fax: 848-38267307
E-mail: [email protected]
Service hours: 8:00 to 12:00 AM and 13:30 to 17:30 PM (from Monday to Friday)
Philippines
Glee Electronics Inc
Contact nos. (632) 636-3636 / 7064028 to 29
Fax no. (632) 7064026
Receiving Centers
NEO CARE - Megamall
4th Level Cyberzone, Building B,
SM Megamall, Mandaluyong City
NEO CARE - SM North EDSA
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/warranty/warcic.htm（第7／9页）2010-1-1111:54:01
ConsumerInformationCenters
4th Level Cyberzone, Annex Bldg.
SM City North EDSA, Quezon City
441-1610
MDR Microware Sales Inc.
Cebu Branch
N. Escario corner Clavano St., Cebu City Phils.
# 255-4415/ 255-3242/253-9361/4124864 to 67
Sun # 0922-8210045 to 46
Davao Office:
C. Arellano St., Davao City 8000
082- 225-3021/225-3022
Sun# 0922-8210015
CDO Office:
1445 Corrales Ext.,CDO City
088-856-8540/856-8541
Sun # 0922-8210080
Iloilo Office:
C. Lim Comp., Gomez St., Iloilo City
# 033 338-4159/ 033 508-3741
Sun # 0922-8808850
Africa
SOUTH AFRICA
Company name: Sylvara Technologies Pty Ltd
Address: Ho Address Palm Springs Centre Christoffel Road Van Riebeeck Park Kempton Park, South Africa
Tel: +27878084456
Fax: +2711 391 1060
E-mail: [email protected]
Service hours: Mon.~ Fri. 08:00am~05:00pm
Middle East
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/warranty/warcic.htm（第8／9页）2010-1-1111:54:01
ConsumerInformationCenters
Middle East + North Africa
Company: AL SHAHD COMPUTER L.L.C
Address: P.O.BOX: 29024, DUBAI, UNITED ARAB EMIRATES
TEL: 00971 4 2276525
FAX: 00971 4 2276242
E-mail: [email protected]
Service hours: Sat.~Thur. 9:00am~1:00pm & 4:00pm- 8:00pm
Israel
Company: Eastronics LTD
Address: 13 Rozanis St. P.O.B. 39300, Tel Aviv 61392 Israel
Tel: 1-800-567000 call free in Israel; (972-50-8353722 after service hours until 20:00)
Fax: 972-3-6458759
E-mail: [email protected]
Service hours: Sun.~Thurs. 08:00 - 18:00
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/warranty/warcic.htm（第9／9页）2010-1-1111:54:01
InternationalGuarantee
Your International Guarantee
Dear Customer,
Thank you for purchasing this Philips product which has been designed and manufactured to the
highest quality standards.
If, unfortunately, something should go wrong with this product Philips guarantees free of charge
labor and replacement parts irrespective of the country where it is repaired during a period of 12
months from date of purchase. This international Philips guarantee complements the existing
national guarantee obligations to you of dealers and Philips in the country of purchase and does not
affect your statutory rights as a customer.
The Philips guarantee applies provided the product is handled properly for its intended use, in
accordance with its operating instructions and upon presentation of the original invoice or cash
receipt, indicating the date of purchase, dealer's name and model and production number of the
product.
The Philips guarantee may not apply if:
●
●
the documents have been altered in any way or made illegible;
the model or production number on the product has been altered, deleted, removed or made
illegible;
●
●
repairs or product modifications and alterations have been executed by unauthorized service
organizations or persons;
damage is caused by accidents including but not limited to lightning, water or fire, misuse or
neglect.
Please note that the product is not defective under this guarantee in the case where modifications
become necessary in order for the product to comply with local or national technical standards
which apply in countries for which the product was not originally designed and/or manufactured.
Therefore always check whether a product can be used in a specific country.
In case your Philips product is not working correctly or is defective, please contact your Philips
dealer. In the event you require service whilst in another country a dealer address can be given to
you by the Philips Consumer Help Desk in that country, the telephone and fax number of which can
be found in the relevant part of this booklet.
In order to avoid unnecessary inconvenience, we advise you to read the operating instructions
carefully before contacting your dealer. If you have questions which your dealer cannot answer or
Website: http://www.philips.com
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/warranty/war_intl.htm（第1／2页）2010-1-1111:54:05
InternationalGuarantee
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/warranty/war_intl.htm（第2／2页）2010-1-1111:54:05
UnitedStatesGuarantee
Your Philips F1rst Choice Warranty(USA)
Thank you for purchasing this Philips monitor.
All Philips monitors are designed and manufactured to high standards and
deliver high-quality performance, ease of use and ease of installation. Should
you encounter any difficulties while installing or using this product, please
contact Philips directly to benefit from your Philips F1rst Choice Warranty. This
three-year service warranty entitles you to a swap model on-site within 48
hours of your call being received within the first year of purchase. If you have
any problems with your monitor within the second or third year of purchase, we
will repair it after it has been sent to the service provider at your expense and
returned to you within five working days, free of charge.
LIMITED WARRANTY (Computer Monitor)
Three Years Free Labor / Three Years Free Service on Parts / One Year Exchange*
*Product will be exchanged with a new or renewed to original specifications unit within two
business days for the first year. This product must be shipped in at your expense for service during
years two and three.
WHO IS COVERED?
You must have proof of purchase to receive warranty service. A sales receipt or other document
showing that you purchased the product is considered proof of purchase. Attach it to this owner's
manual and keep both nearby.
WHAT IS COVERED?
Warranty coverage begins the day you buy your product. For three years thereafter, all parts will be
repaired or replaced, and labor is free. After three years from the day of purchase, you pay for the
replacement or repair of all parts, and for all labor charges.
All parts, including repaired and replaced parts, are covered only for the original warranty period.
When the warranty on the original product expires, the warranty on all replaced and repaired
products and parts also expires.
WHAT IS EXCLUDED?
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/warranty/war_usa.htm（第1／4页）2010-1-1111:54:10
UnitedStatesGuarantee
Your warranty does not cover:
●
●
●
●
labor charges for installation or setup of the product, adjustment of customer controls on the
product, and installation or repair of antenna systems outside of the product.
product repair and/or part replacement because of misuse, accident, unauthorized repair or
other cause not within the control of Philips Consumer Electronics.
reception problems caused by signal conditions or cable or antenna systems outside the
unit.
a product that requires modification or adaptation to enable it to operate in any country other
than the country for which it was designed, manufactured, approved and/or authorized, or
repair of products damaged by these modifications.
●
incidental or consequential damages resulting from the product. (Some states do not allow
the exclusion of incidental or consequential damages, so the above exclusion may not apply
to you. This includes, but is not limited to, prerecorded material, whether copyrighted or not
copyrighted.)
●
the model or production number on the product has been altered, deleted, removed or made
illegible.
Where IS SERVICE AVAILABLE?
Warranty service is available in all countries where the product is officially distributed by Philips
Consumer Electronics. In countries where Philips Consumer Electronics does not distribute the
product, the local Philips service organization will attempt to provide service (although there may be
a delay if the appropriate spare parts and technical manual(s) are not readily available).
Where CAN I GET MORE INFORMATION?
For more information, contact the Philips Customer Care Center by calling (877) 835-1838 (U.S.A.
customers only) or (919) 573-7855.
Before Requesting Service...
Please check your owner's manual before requesting service. Adjustments of the controls
discussed there may save you a service call.
TO GET WARRANTY SERVICE IN U.S.A., PUERTO RICO OR U.S. VIRGIN ISLANDS...
Contact the Philips Customer Care Center phone number listed below for product assistance and
procedures for servicing:
Philips Customer Care Center
(877) 835-1838 or (919) 573-7855
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/warranty/war_usa.htm（第2／4页）2010-1-1111:54:10
UnitedStatesGuarantee
(In U.S.A., Puerto Rico and U.S. Virgin Islands, all implied warranties, including implied warranties
of merchantability and fitness for a particular purpose, are limited in duration to the duration of this
express warranty. But, because some states do not allow limitations on how long an implied
warranty may last, this limitation may not apply to you.)
TO GET WARRANTY SERVICE IN CANADA...
Please contact Philips at:
(800) 479-6696
Three years free parts and three years free labor will be provided at Philips Canada depot or any
one of its authorized service centers.
(In Canada, this warranty is given in lieu of all other warranties. No other warranties are expressed
or implied, including any implied warranties of merchantability or fitness for a particular purpose.
Philips is not liable under any circumstances for any direct, indirect, special, incidental or
consequential damages, howsoever incurred, even if notified of the possibility of such damages.)
REMEMBER... Please record the model and serial numbers found on the product below.
MODEL # ________________________________________________
SERIAL # ________________________________________________
This warranty gives you specific legal rights. You may have other rights which vary from state/
province to state/province.
Before contacting Philips, please prepare the following details so we can solve your problem
quickly.
●
●
Philips type number
Philips serial number
●
●
Purchase date (copy of purchase may be required)
PC environment Processor:
❍
❍
❍
CUP and Graphic card name and driver version
Operating system
Application being used
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/warranty/war_usa.htm（第3／4页）2010-1-1111:54:10
UnitedStatesGuarantee
●
●
Other cards installed
Having the following information available will also help speed up the process:
Your proof of purchase indicating: date of purchase, dealer name, model and product serial
number.
●
The full address to which the swap model should be delivered.
Just a phone call away
Philips’ customer help desks are located worldwide. Within the U.S. you can contact Philips
customer care Monday-Friday from 8:00 AM-9:00 PM Eastern Time (ET) and on Saturdays from
10:00 AM-5:00 PM ET hrs by using one of the contact phone numbers.
For more information on this and more great Philips products visit our website at:
Website: http://www.philips.com
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/warranty/war_usa.htm（第4／4页）2010-1-1111:54:10
Glossary
Glossary
A
Active matrix
This is a kind of liquid crystal display structure in which switching transistors are attached to each
pixel to control the on/off voltage. It produces a brighter and sharper display with a broader viewing
angle than a passive matrix display. Also refer to TFT (thin film transistor).
Amorphous silicon (a-Si)
A semiconductor material that is used to make the thin film transistors (TFTs) layer of an active
matrix LCD.
Aspect ratio
The width-to-height ratio of the active area of a display. In general, most monitors have an aspect
ratio of 4:3. Wide monitors or TVs have an aspect ratio of 16:9 or 16:10.
Backlight
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/glossary/glossary.htm（第1／9页）2010-1-1111:54:13
Glossary
The light source for a transmissive LCD. There are two techniques used in nowaday LCD designs.
Most TFT LCD panels use CCFLs (cold cathode fluorescent light) and a diffuser panel directly
behind the liquid crystal layer. New technology using Light Emitting Diodes (LED) are still under
development.
Brightness
The dimension of color that is referred to an achromatic scale, ranging from black to white, also
called lightness or luminous reflectance. Because of confusion with saturation, the use of this term
should be discouraged.
C
CCFL(cold cathode fluorescent light)
These are the fluorescent light tubes providing the light for the LCD module. These tubes are
generally very thin, approximately 2 mm in diameter.
Chromaticity
That part of color specification, which does not involve illuminance. Chromaticity is two-dimensional
and specified by pairs of numbers such as dominant wavelength and purity.
CIE (Commission International de I'Eclairage)
The International Commission on Illumination, the primary international organization concerned with
color and color measurement.
Color temperature
A measurement of the color of light radiated by an object while it is being heated. This
measurement is express in terms of absolute scale, (degrees Kelvin). Lower Kelvin temperatures
such as 2400° K are red; higher temperatures such as 9300° K are blue. Neutral temperature is
white, at 6504° K. Philips monitors generally offers 9300° K, 6500° K, and user define.
Contrast
The luminance variation between light and dark areas in an image.
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/glossary/glossary.htm（第2／9页）2010-1-1111:54:13
Glossary
Contrast ratio
The ratio of luminance between the brightest white pattern and the darkest black pattern.
D
D-SUB
A VGA Analog input connector. Your monitor comes with a D-Sub cable.
Digital Visual Interface (DVI)
The Digital Visual Interface (DVI) specification provides a high-speed digital connection for visual
data types that is display technology independent. The interface is primarily focused at providing a
connection between a computer and its display device. The DVI specification meets the needs of all
segments of the PC industry (workstation, desktop, laptop, etc.) and will enable these different
segments to unite around one monitor interface specification.
The DVI interface enables:
1. Reduce signal loss and video noise in signal due to less signal conversion.
2. Independent from display technology, and can be used on LCD, Plasma, LCOS, etc.
3. Plug and play through hot plug detection, EDID and DDC2B.
4. Digital and Analog support in a single connector (DVI-I only).
E
Energy Star Computers Program
An energy conservation program launched by the US Environmental Protection Agency (EPA),
promotes the manufacture and marketing of energy-efficient office automation equipment.
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/glossary/glossary.htm（第3／9页）2010-1-1111:54:14
Glossary
Companies joining this program, must be willing to commit themselves to manufacture one or more
products capable of going into a low -power state (< 30 W) either after a period of inactivity, or after
a predetermined time selected by the user.
Gamma
Screen luminance as a function of video voltage approximately follows a mathematical power
function of the input video signal, the exponent of which is called gamma.
Grayscale
An achromatic scale ranging from black through a series of successively lighter grays to white.
Such a series may be made up of steps, which appear to be equally distant from one another. If the
8
Analog/ Digital converter is 8 bit, then the monitor can display at most 2 = 256 levels. For a color
monitor, R.G.B. each color hads 256 levels. Thus, total color can display is 256x256x256= 16.7
million.
Hue
The main attribute of a color that distinguishes it from other colors. For example, a color may have a
green, yellow, or purple hue. Color defined as having hue are know as chromatic colors. White,
black, and grays possess no hue.
IPS (In Plane Switching)
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/glossary/glossary.htm（第4／9页）2010-1-1111:54:14
Glossary
A technique of improving the viewing angle of an LCD where the liquid crystal molecules are
switched in the plane of the LCD layer rather than vertical to it.
L
LCD (liquid crystal display)
A display composed of liquid crystal suspended between two transparent sheets. The display is
composed thousands of pixels which can be turned on or off with electrical stimulation. Thus,
colorful images/texts can be generated.
Liquid crystal
The compound found in liquid crystal displays. Liquid crystal reacts predictably when electrically
stimulated. This makes it the ideal compound to turn LCD pixels "on" or "off." Liquid crystal is
sometimes abbreviated as LC.
Luminance
A measure of the brightness or luminous intensity of light, usually expressed in units of Candelas
per square meter (cd/m2) or foot Lamberts. 1 fL=3.426 cd/m2.
Nit
A unit of luminance equal to 1 cd/m2 or 0.292 ftL.
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/glossary/glossary.htm（第5／9页）2010-1-1111:54:14
Glossary
Pixel
PICture Element; the smallest element on a computerized CRT or LCD image, and hence a display.
Polarizer
A light filter which only allows light waves of a certain rotation through. Polarized material with
perpendicular filtering is used in LCDs to enclose the liquid crystal. The liquid crystal is then used
as the medium which twists the light waves 90° in order to allow the light to pass through or not.
Refresh rate
The number of times per second the screen is refreshed or redrawn. This number is usually stated
in Hz (Hertz) or cycles per second. A rate of 60 Hz is equal to 60 tomes per second.
S
sRGB
sRGB is a standard for ensuring correct exchange of colors between different devices (e.g. digital
cameras, monitors, printers, scanners, etc.)
Using a standard unified color space, sRGB will help represent pictures taken by an sRGB
compatible device correctly on your sRGB enabled Philips monitors. In that way, the colors are
calibrated and you can rely on the correctness of the colors shown on your screen.
Important with the use of sRGB is that the brightness and contrast of your monitor is fixed to a
predefined setting as well as the color gamut. Therefore it is important to select the sRGB setting in
the monitor's OSD.
To do so, open the OSD by pressing the OK button on the front of your monitor. Move the down
button to go to Color and press OK again. Use the right button to go to sRGB. Then move the down
button and press OK again to exit the OSD.
After this, please do not change the brightness or contrast setting of your monitor. If you change
either of these, the monitor will exit the sRGB mode and go to a color temperature setting of 6500K.
Other:
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/glossary/glossary.htm（第6／9页）2010-1-1111:54:14
Glossary
USB plug: An upstream and a downstream USB plug is provide for user's convenience.
TFT(thin film transistor)
Usually made from amorphous silicon (a-Si) and used as a switch to a charge storage device
located below each sub-pixel on an active matrix LCD.
U
USB or Universal Serial Bus
A smart plug for PC peripherals. USB automatically determines resources (like driver software and
bus bandwidth) required by peripherals. USB makes necessary resources available without user
intervention.
●
USB eliminates "case anxiety" -- the fear of removing the computer case to install add-on
peripherals. USB also eliminates adjustment of complicated IRQ settings when installing
new peripherals.
●
USB does away with "port gridlock." Without USB, PCs are normally limited to one printer,
two Com port devices (usually a mouse and modem), one Enhanced Parallel Port add-on
(scanner or video camera, for example) and a joystick. More and more peripherals for
multimedia computers arrive on the market every day. With USB, up to 127 devices can run
simultaneously on a computer.
●
USB permits "hot plug-in." There's no need to shut down, plug in, reboot and run set-up to
install peripherals. And no need to go through the reverse process to unplug a device.
In short, USB transforms today's "Plug-and-Pray" into true Plug-and-Play!
Hub
A Universal Serial Bus device that provides additional connections to the Universal Serial Bus.
Hubs are a key element in the plug-and-play architecture of USB. The Figure shows a typical hub.
Hubs serve to simplify USB connectivity from the user's perspective providing low cost and
complexity.
Hubs are wiring concentrators and enable the multiple attachment characteristics of USB.
Attachment points are referred to as ports. Each hub converts a single attachment point into
multiple attachment points. The architecture supports concatenation of multiple hubs.
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/glossary/glossary.htm（第7／9页）2010-1-1111:54:14
Glossary
The upstream port of a hub connects the hub towards the host. Each of the other downstream ports
of a hub allows connection to another hub or function. Hubs can detect, attach and detach at each
downstream port and enable the distribution of power to downstream devices. Each downstream
port can be individually enabled and configured at either full or low speed. The hub isolates low
speed ports from full speed signaling.
A hub consists of two portions: the Hub Controller and Hub Repeater. The repeater is a protocol-
controlled switch between the upstream port and downstream ports. It also has hardware support
for reset and suspend/resume signaling. The controller provides the interface registers to allow
communication to/from the host. Hub specific status and control commands permit the host to
configure a hub and to monitor and control its ports.
Device
A logical or physical entity that performs a function. The actual entity described depends on the
context of the reference. At the lowest level, device may refer to a single hardware component, as
in a memory device. At a higher level, it may refer to a collection of hardware components that
perform a particular function, such as a Universal Serial Bus interface device. At an even higher
level, device may refer to the function performed by an entity attached to the Universal Serial Bus;
for example, a data/FAX modem device. Devices may be physical, electrical, addressable, and
logical.
Downstream
The direction of data flow from the host or away from the host. A downstream port is the port on a
hub electrically farthest from the host that generates downstream data traffic from the hub.
Downstream ports receive upstream data traffic.
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/glossary/glossary.htm（第8／9页）2010-1-1111:54:14
Glossary
Upstream
The direction of data flow towards the host. An upstream port is the port on a device electrically
closest to the host that generates upstream data traffic from the hub. Upstream ports receive
downstream data traffic.
V
Vertical refresh rate
Expressed in Hz, it is the number of frames (complete pictures) written to the screen every second.
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/160EL1/glossary/glossary.htm（第9／9页）2010-1-1111:54:14
DownloadandPrint
Download and Print
Installing Your LCD monitor driver
System requirements:
●
●
PC running Windows 95, Windows® 98, Windows® 2000 , Windows® Me, Windows® XP,
Windows® Vista or later
Find your driver ".inf/.icm/.cat" at : /PC/drivers/
Read the "Readme.txt" file before installing.
This page provides an option to read the manual in .pdf format. PDF files can be downloaded into
your hard disk, then viewed and printed with Acrobat Reader or through your browser.
If you do not have Adobe® Acrobat Reader installed, click on the link to install the application.
To view some documentation (.pdf files), you must have the Adobe Acrobat Reader program installed on
your computer. If it is not installed, you will receive an error message. For your convenience, Adobe Acrobat
Reader installers for the languages listed below, are included on this CD. Click on your Language below, to
install the Adobe Reader for your Language. Note: Only the English installer includes the features for
searching Adobe .pdf files and accessibility support. Installers for other languages, with these additional
Download instructions:
To download the file:
1. Click-and-hold your mouse over the icon below. (Windows® 95/98/ 2000/Me/XP/Vista users right-
click)
Download
2. From the menu that appears, choose 'Save Link As...', 'Save Target As...' or 'Download Link to
Disk'.
3. Choose where you would like to save the file; click 'Save' (if prompted to save as either 'text' or
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/download/download.htm（第1／2页）2010-1-1111:54:16
DownloadandPrint
'source', choose 'source').
Printing instructions:
To print the manual:
With the manual file open, follow your printer's instructions and print the pages you need.
file:///E|/manualSPEC/813/spec/cd/16/Q70G16C18131A 160EL1/CD/lcd/manual/ENGLISH/download/download.htm（第2／2页）2010-1-1111:54:16
|