Table of Contents
15B2322Q
MAIN MENU / GEOMETRY WINDOW
GETTING STARTED
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
SAFETY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
DESCRIPTION OF CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
SETTING UP GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Foldout
Rotation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Pincushion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Trapezoid. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Balanced Pincushion . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Parallelogram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
HOW TO USE THE ON SCREEN DISPLAY
FRONT PANEL CONTROLS
MAIN MENU / SIZE & POSITION WINDOW
Zoom. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Horizontal Position. . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Horizontal Size. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Vertical Position. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Vertical Size. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Brightness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
MAIN MENU
Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Degauss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Monitor Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
MAIN MENU / SAVE & CANCEL. . . . . . . . . . . . . . . . . . . . . . . . . 15
MAIN MENU / EXIT OSD & RESET . . . . . . . . . . . . . . . . . . . . . . 15
MAIN MENU / ADVANCED CONTROLS WINDOW
ADDITIONAL INFORMATION
Power Saving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
DDC1 / 2B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
OSD Timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Moire. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Sync Input Select. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
AUDIO & USB SET UPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
POWER SAVING FEATURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
GLOSSARY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
PIN ASSIGNMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
TROUBLESHOOTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
WARRANTY (APPENDIX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
MAIN MENU / COLOR TEMPERATURE WINDOW
9300˚ K . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
6500˚ K . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
User 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
User 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Other language versions
FRENCH (FRANCAIS). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
appendix
ENGLISH
Information for Users in the U.S. . . . . . . . . . . . . . . . . . . . . . . . . . . A1
DECLARATION FCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A2
ENERGY DECLARATION
Hinweis / GS /ACHTUNG. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A4
DECLARATION FCC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A5
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3
DEUTSCH
FRANCAIS
BECAUSE OF A POLICY OF CONTINUOUS PRODUCT IMPROVEMENT,
THE INFORMATION MENTIONED IN THIS DOCUMENTS IS SUBJECT TO CHANGE WITHOUT NOTICE.
Description of Controls
VOLUME Button – Press the button to adjust the sound from
the speakers.
BRIGHTNESS Button –
POWER
CONTRAST Button – Press this
button to adjust the screen’s
contrast.
Press the button to
adjust the screen’s
brightness.
Button –
Turns the
electricity
On and
Off.
TOP VIEW
LED – Light Emitting Diode
turns green when the monitor is
on and at full power.
EARPHONES Jack – Plug in earphones
here. This mutes the sound from the
front speakers.
BUILT-IN MICROPHONE –
Allows you to “speak” to
your computer.
FRONT VIEW
LEFT VIEW
ON SCREEN DISPLAY (OSD) Button –
Brings up the On Screen Display and
helps you navigate through it.
ROTARY Knob – Helps guide you through the On
Screen Display and also adjusts settings such as
Volume, Brightness, and Contrast.
SPEAKERS – Transmit
MICROPHONE Jack – Plug in a
microphone to transmit
sound through the side
speakers or to the computer.
See page 16.
sounds from your
computer or amplifier.
One speaker on each
side of the monitor.
REAR VIEW
USB Connector (under the edge, optional) – Slot
for plugging in the USB Hub-optional hardware that
allows true Plug-and-Play. For details, see page 16.
AUDIO IN Jack – Connect the supplied audio cable to
send sound from a computer or amplifier to the
monitor’s speakers.
MICROPHONE OUT Jack – Connect the supplied
microphone cable to transmit sound from the
monitor to a computer or amplifier.
VIDEO IN Jack – One end of the cable is already connected here. The other
end connects to the computer. See foldout for details.
POWER Plug – Plug the power cord in
here. See foldout for details.
2
Description of Controls
FRONT PANEL BUTTONS / ROTARY KNOB
PEDESTAL
110
50
USING THE FRONT PANEL
BUTTONS – Select one
of the four front
panel buttons, then
use the Rotary knob
to make the
900
900
adjustment or select
an additional
feature. To adjust a
particular feature,
see the page for that
feature. For
example, Contrast is
on page 4.
PEDESTAL – With the built-in pedestal,
you can tilt and swivel the monitor to
the most comfortable viewing angle.
To best use your monitor, always
place it at eye level.
ON SCREEN DISPLAY – Your monitor is preset at the factory. However, you can adjust it using the ON SCREEN DISPLAY button
and the ROTARY knob described on page 2. The way to do so is through the On Screen Display (OSD). Below is a brief
description of the seven On Screen Display windows.
SIZE & POSITION – This menu item helps you maximize the position of your
screen. It has five features: ZOOM, HORIZONTAL POSITION, HORIZONTAL SIZE, VERTICAL
POSITION, and VERTICAL SIZE. To adjust these features, turn to pages 13 - 14.
GEOMETRY CONTROLS – This
menu item has five features:
PINCUSHION, BALANCED PINCUSHION,
TRAPEZOID, PARALLELOGRAM, and
ROTATION. To adjust these
features, turn to page 12.
COLOR TEMPERATURE –
Select the
MONITOR STATUS –
Lists the current
vertical and
horizontal scanning
frequencies and
tells you the serial
number of the
ADVANCED CONTROLS – This menu
item has six features: POWER
SAVING, LANGUAGE,
DEGAUSS –
MUTE – Turns
the sound
from your
speakers On
or Off. Mute
Off is the
default. For
details, see
page 5.
Demagnetizes
your screen. If
color splotches
or impurities
appear on your
screen, you
may want to
try this. For
details, see
page 6.
temperature setting
for the best color for
your work. You can
even customize your
color settings. There
are four selections:
9300˚ K, 6500˚ K, USER
1, and USER 2. For
details, turn to pages
10 - 11.
DDC1 / 2B, OSD TIMER,MOIRE, and
SYNC INPUT SELECT. To adjust these
features, turn to pages 7 - 9.
Note: LANGUAGE allows you to
change the On Screen Display
from English to French, Spanish,
German, or Italian. See page 7
for details.
monitor. For details,
see page 6.
3
How to Use the On Screen Display (OSD)
Front Panel Controls
Contrast
Brightness
To adjust your screen’s contrast, follow the steps below.
Contrast is the difference between the light and dark areas on
the screen. A 100% contrast level is recommended.
To adjust your screen’s brightness, follow the steps below.
Brightness is the overall intensity of the light coming from the
screen. A 50% brightness level is recommended.
1
Press the Contrast button
1
Press the Brightness
(furthest one on the
right) on the front of the
monitor.
button (second one
from the left) on the
front of the monitor.
The Contrast
window appears.
The Brightness
window appears.
2
2
Turn the
Turn the
ROTARY knob
(at the
lower right-
hand corner
of the
monitor) to
adjust the
contrast.
ROTARY knob
(at the lower
right-hand
corner of
the monitor)
to adjust the
brightness.
3
3
When
When
finished,
press the
BRIGHTNESS
button
again. The
Brightness
screen
finished,
press the
CONTRAST
button
again. The
Contrast
screen
disappears
.
disappears.
Smart Help
Smart Help
To continue to Brightness, press the BRIGHTNESS button on the front
of the monitor. Next, follow steps 2 - 3 under BRIGHTNESS.
To continue to Volume, press the VOLUME button on the front of the
monitor. Next, follow steps 2 - 3 under VOLUME.
If you do not press the CONTRAST button a second time, the
Contrast window will “time out” (disappear) after five seconds. You
can change this time. See page 8 for time out options.
If you do not press the BRIGHTNESS button a second time, the
Contrast window will “time out” (disappear) after five seconds. You
can change this time. See page 8 for time out options.
4
How to Use the On Screen Display (OSD)
Front Panel Control / Main Menu
Volume
Mute
To completely turn off the volume (but still return to the
To adjust your monitor’s volume, follow the steps below. The
former level), follow the steps below. The mute control turns
off the sound from the two front-mounted speakers or the earphones
jack. Note: audio is muted from monitor speakers when earphones
are connected. See pages 2 and 16 for details.
volume control adjusts the sound from the two front-
mounted speakers or the earphones jack.
Press the ON SCREEN
DISPLAY button.
1
1
Press the Volume
button (first one from
the left) on the front of
the monitor.
The Main Menu appears
and the MUTE icon is
highlighted. MUTE OFF
appears by the icon.
The Volume window
appears.
2
Turn the
ROTARY knob
(at the
lower right-
hand corner
of the
monitor) to
adjust the
volume.
2
Press the ON SCREEN DISPLAY
4
To turn the
mute off, press
the On Screen
Display button
and repeat
button a second time. MUTE
ON appears by the icon and
EXIT OSD Is highlighted.
steps 2 - 3.
3
When
finished,
press the
VOLUME
button
again. The
Volume
screen
disappears
.
3
Press the ON SCREEN DISPLAY (OSD)
button a third time to exit the OSD.
Smart Help
To go to DEGAUSS . . .
Smart Help
. . . instead of pressing the ON SCREEN DISPLAY (OSD) button a third time,
turn the ROTARY knob until DEGAUSS is highlighted. Next, press the OSD
button. Turn to the next page and follow steps 2 - 3.
After Volume Window has disappeared, to continue to the Main
Menu, press the larger OSD (On Screen Display) button between the
BRIGHTNESS and CONTRAST buttons. Next, follow steps 2 - 3 under MUTE.
. . . once you have exited the OSD, press the OSD button and turn the
Rotary knob until DEGAUSS is highlighted. Next, press the OSD button.
Turn to the next page and follow steps 2 - 3.
If you do not press the VOLUME button a second time, the Volume
window will “time out” (disappear) after five seconds. You can
change this time. See page 8 for time out options.
If you do not press the OSD button a third time, the OSD window
will “time out” (disappear) after five seconds. You can change this time.
See page 8 for time out options.
5
How to Use the On Screen Display (OSD)
Main Menu windows
Degauss
Monitor Status
Degaussing removes electromagnetic build up that may distort
the color on your screen. To degauss your screen, follow the
steps below.
Monitor Status tells you the vertical and horizontal scanning
frequencies that your computer is using to operate your
monitor. It also tells you the serial number of your monitor. Note: This
screen is for review only.
Press the ON SCREEN
DISPLAY button.
1
Press the ON SCREEN
DISPLAY button.
1
Turn the ROTARY
knob until MONITOR
STATUS is
2
Turn the ROTARY
knob until DEGAUSS
is highlighted.
2
highlighted.
4
Press the ON
Press the ON SCREEN
DISPLAY button to bring
up the MONITOR STATUS
screen.
SCREEN DISPLAY
button to exit
the Monitor
Status screen
and return to
the Main
3
Press the ON SCREEN
DISPLAY
3
button to degauss
your screen.
For a moment, the
screen will be
distorted. Then it
will return to
normal. You will be
at Main Menu. EXIT
OSD will be
Menu. EXIT
OSD will be
highlighted.
highlighted.
Smart Help
After returning to the Main Menu . . .
Smart Help
After returning to the Main Menu . . .
. . . to continue to ADVANCED CONTROLS, turn the ROTARY knob until
ADVANCED CONTROLS is highlighted. Next, follow steps 2 - 3 under
ADVANCED CONTROLS on the next page.
. . . to continue to MONITOR STATUS, turn the ROTARY knob until MONITOR
STATUS is highlighted. Next, follow steps 2 - 3 under MONITOR STATUS in
the next column.
. . . to exit completely, press the OSD button.
Note: Neither the scanning frequencies nor the serial number
can be changed at this screen. The scanning frequencies are
established by your computer. They also appear at the top of the
Main Menu screen. The serial number is entered at the factory.
. . . to exit completely, press the OSD button.
6
How to Use the On Screen Display (OSD)
Advanced Controls window
Language
Power Saving
The On Screen Display shows its settings in one of five
POWER SAVING helps save energy when the monitor is on but not
languages. The default is English, but you can select French,
Spanish, German, or Italian. To select LANGUAGE, follow the steps below.
being used. After a preset time, the monitor will go blank if not
being used. “POWER SAVING ON” is the default setting. To turn POWER
SAVING OFF, follow the steps below.
Press the ON SCREEN
DISPLAY button.
Press the ON SCREEN
DISPLAY button.
1
1
Turn the ROTARY
2
knob until the
2
Turn the ROTARY knob
until the ADVANCED
CONTROLS window is
highlighted. Next,
press the ON SCREEN
DISPLAY button. Then,
turn the ROTARY knob
until LANGUAGE is
ADVANCED CONTROLS
window is
highlighted. Next,
press the ON SCREEN
DISPLAY button.
highlighted.
6
Press the
ON SCREEN
DISPLAY button to
exit the Main
Menu.
Press the ON SCREEN
DISPLAY button to
3
5
change to POWER
Press the
SAVING OFF.
ON SCREEN
Press the ON SCREEN
DISPLAY button to
bring up LANGUAGE
screen.
3
DISPLAY button
to exit the Main
Menu.
Press the ON SCREEN
DISPLAY button again to
save your selection.
4
5
Press the ON
SCREEN DISPLAY
button again to
save your
4
Turn the ROTARY knob until the desired
language is selected. Then, press the
ON SCREEN DISPLAY button. Note: a
checkmark appears beside the
current selection.
selection.
Smart Help
Smart Help
To make other changes in the ADVANCED CONTROLS window . . .
To make other changes in the ADVANCED CONTROLS window . . .
. . . after returning to ADVANCED CONTROLS window [but before pressing
the ON SCREEN DISPLAY (OSD) button in STEP 5], turn the ROTARY knob
until another feature – for example, DDC1 / 2B – is highlighted. Next,
turn to the next page and follow steps 2 - 5 under DDC1 / 2B.
. . . after returning to ADVANCED CONTROLS window [but before pressing
the ON SCREEN DISPLAY (OSD) button in STEP 4], turn the ROTARY knob
until another feature – for example, LANGUAGE – is highlighted. Next,
follow steps 2 - 6 under LANGUAGE.
. . . after you have exited completely, press the OSD button and
follow the steps under that feature, for example, DDC1 / 2B.
. . . after you have exited completely, press the OSD button and
follow the steps under that feature, for example, LANGUAGE.
7
How to Use the On Screen Display (OSD)
Advanced Controls window
DDC1 / 2B
OSD Timer
Many newer computers have DDC technology that this monitor
With OSD TIMER you can set the time for the On Screen Display
to time out. Your choices range from 5 to 50 seconds. To select
OSD TIMER, follow the steps below. Note: Ten seconds is the default
setting.
takes advantage of to provide you better picture quality.
“DDC1 / 2B ON” is the default setting. If your computer’s video card is
not DDC compatible, you may experience interference,“noise,” or no
color on your monitor. If so, try turning this feature off.
Press the ON SCREEN
DISPLAY button.
Press the ON SCREEN
DISPLAY button.
1
1
2
Turn the ROTARY knob
until the ADVANCED
CONTROLS window is
highlighted. Next,
press the ON SCREEN
DISPLAY button. Then,
turn the ROTARY knob
until DDC1 / 2B ON is
highlighted.
2
Turn the ROTARY knob
until the ADVANCED
CONTROLS window is
highlighted. Next,
press the ON SCREEN
DISPLAY button. Then,
turn the ROTARY knob
until OSD TIMER is
highlighted.
6
Press the
ON SCREEN
5
Press the
ON SCREEN
DISPLAY button to
exit the Main
Menu.
DISPLAY button
to exit the Main
Menu.
Press the ON SCREEN
DISPLAY button to
change to DDC1 /
2B OFF.
3
Press the ON SCREEN
DISPLAY button to
bring up OSD TIMER
screen.
3
5
4
Press the ON SCREEN DISPLAY
button again to save your
selection.
Press the ON
SCREEN DISPLAY
button again to
save your
4
Turn the ROTARY knob until the
desired time out period is
selected. Then, press the ON
SCREEN DISPLAY button. Note: a
checkmark appears beside the
current OSD TIMER period.
selection.
Smart Help
Smart Help
To make other changes in the ADVANCED CONTROLS window . . .
To make other changes in the ADVANCED CONTROLS window . . .
. . . after returning to ADVANCED CONTROLS window [but before pressing
the ON SCREEN DISPLAY (OSD) button in STEP 4], turn the ROTARY knob
until another feature – for example, OSD TIMER – is highlighted. Next,
follow steps 2 - 6 under OSD TIMER.
. . . after returning to ADVANCED CONTROLS window [but before pressing
the ON SCREEN DISPLAY (OSD) button in STEP 5], turn the ROTARY knob
until another feature – for example, MOIRE – is highlighted. Next, turn
to the next page and follow steps 2 - 6 under MOIRE.
. . . after you have exited completely, press the OSD button and
follow the steps under that feature, for example, OSD TIMER.
. . . after you have exited completely, press the OSD button and
follow the steps under that feature, for example, MOIRE.
8
How to Use the On Screen Display (OSD)
Advanced Controls window
Sync Input Select
Moire
Moire is a fringe pattern arising from the interference between
SYNC INPUT SELECT synchronizes your monitor with the video
card in your computer. In most cases you will not need to use
this feature. To adjust your SYNC INPUT SELECT, follow the steps below.
Note: Use only if necessary. If your screen has a greenish cast to it that
cannot be adjusted for with the Color Temperature controls on pages
10 and 11, then try this.
two superimposed line patterns. To adjust your Moire, follow
the steps below. Note: Use only if necessary. Activating Moire can
affect sharpness.
Press the ON SCREEN
DISPLAY button.
Press the ON SCREEN
DISPLAY button.
1
1
2
Turn the ROTARY knob
until the ADVANCED
CONTROLS window is
highlighted. Next,
press the ON SCREEN
DISPLAY button. Then,
turn the ROTARY knob
until MOIRE is
2
Turn the ROTARY knob
until the ADVANCED
CONTROLS window is
highlighted. Next,
press the ON SCREEN
DISPLAY button. Then,
turn the ROTARY knob
until SYNC INPUT SELECT
is highlighted.
highlighted.
6
Once you
have made
6
Press the
ON SCREEN
the adjustments, press
the ON SCREEN DISPLAY
button once to save your
changes, then again to
exit the Advanced
Controls window, and a
third time to exit the Main
Menu.
DISPLAY button to
exit the Main
Menu.
Press the ON SCREEN
DISPLAY button twice to
bring up MOIRE screen
and highlight
3
Press the ON SCREEN
DISPLAY button to
bring up SYNC INPUT
SELECT screen.
3
H(ORIZONTAL) MOIRE.
5
To adjust
5
the VERTICAL MOIRE, turn
the Rotary knob until
V(ERTICAL) MOIRE is
highlighted. Then, press
the ON SCREEN DISPLAY
button again and repeat
step 4.
Press
the ON SCREEN
DISPLAY button
again to save
your selection.
4
Turn the ROTARY knob until the
desired HORIZONTAL MOIRE is
selected. Then, press the ON
SCREEN DISPLAY button.
Turn the ROTARY knob until either
TTL SYNC or SYNC ON GREEN is
selected. Then, press the ON SCREEN
DISPLAY button. Note: a checkmark
appears beside the current SYNC
INPUT selected.
4
Smart Help
Smart Help
To make other changes in the Main Menu window . . .
To make other changes in the ADVANCED CONTROLS window . . .
. . . after returning to THE Main Menu [but before pressing the ON SCREEN
DISPLAY (OSD) button in STEP 6], turn the ROTARY knob until another
feature – for example, COLOR TEMPERATURE – is highlighted. Next, press
the OSD button, turn to the next page and follow steps 2 - 7 under
COLOR TEMPERATURE.
. . . after returning to ADVANCED CONTROLS window [but before pressing
the ON SCREEN DISPLAY (OSD) button a third time in STEP 6], turn the
ROTARY knob until another feature – for example, SYNC INPUT SELECT – is
highlighted. Next, follow steps 2 - 6 under SYNC INPUT SELECT.
. . . after you have exited completely, press the OSD button and follow
the steps under that feature, for example, SYNC INPUT SELECT.
. . . after you have exited completely, press the OSD button and use the
ROTARY knob to select that feature, for example, COLOR TEMPERATURE.
9
How to Use the On Screen Display (OSD)
Color Temperature window
9300˚ K / 6500˚ K
Your monitor has two preset options you select: 9300˚ K or 6500˚ K. Computer Aided Design (CAD) usually works best with the 9300˚ K setting.
Desktop Publishing (DTP) usually works best with the 6500˚ K setting. The screen will change as you scroll between these two settings. Select
the one that works best for you, or set up your own setting under USER 1 or USER 2 on the next page.
Press the ON SCREEN
DISPLAY button.
1
Turn the ROTARY knob
until the COLOR
2
TEMPERATURE window
is highlighted. Then
press the ON SCREEN
DISPLAY button.
3
Turn the ROTARY knob until 9300˚ K or
6500˚ K is highlighted. Note: a checkmark
appears beside the current selection.
After the preset setting
5
is saved, the on screen
display automatically
returns to the Main
Menu. To exit, press the ON
SCREEN DISPLAY button.
4
Press the ON SCREEN DISPLAY button. A
checkmark appears by your selection. Press the ON SCREEN
DISPLAY button a second time to save your selection.
Smart Help
After returning to Main Menu . . .
. . . to continue to USER 1 or USER 2, turn the ROTARY knob until COLOR TEMPERATURE is highlighted. Next, follow steps 2 - 7 under COLOR TEMPERATURE on the
next page.
. . . to select the other preset setting (9300˚ K or 6500˚ K), press the OSD button and repeat steps 2 -5.
10
How to Use the On Screen Display (OSD)
Color Temperature window
User 1 / User 2
USER 1 and USER 2 allow you to individually set the mixture of red, green, and blue that establishes the color balance on your monitor’s screen.
You can set up to two presets, then select between them for different tasks. You can only use one preset at a time
Press the ON SCREEN
DISPLAY button.
1
Turn the ROTARY knob until the COLOR TEMPERATURE
2
3
Turn the Rotary
window is highlighted. Next, press the ON SCREEN
knob until User
DISPLAY button.
1 is highlighted.
Note: a
checkmark
appears beside
the current
selection.
When done with the blue, press
7
the On Screen Display button to
save the changes. Next, see SMART
HELP below for options.
When done with red, press the
ON SCREEN DISPLAY button.
GREEN will be highlighted.
5
When done with green, press
the ON SCREEN DISPLAY button.
BLUE will be highlighted.
6
First, press the ON SCREEN
DISPLAY button. RED will be
highlighted.
4
Next, to adjust the green,
press the ON SCREEN DISPLAY
button again. Then, turn the
ROTARY knob to increase or
decrease the green.
Next, to adjust the blue, press
the ON SCREEN DISPLAY button
again. Then, turn the ROTARY
knob to increase or decrease
the blue.
Next, to adjust the red, press
the ON SCREEN DISPLAY button
again. Then, turn the ROTARY
knob to increase or decrease
the red.
Smart Help
After returning to COLOR TEMPERATURE . . .
. . . to continue to USER 2, turn the ROTARY knob until User 2 is highlighted. Then, press the ON SCREEN DISPLAY button and follow steps 4 - 7.
. . . to continue to the Main Menu, press the ON SCREEN DISPLAY button once more after completing step 7 above. Now, to select another window from
the Main Menu – for example, GEOMETRY – turn to the next page and follow steps 2a - 5c.
. . .to exit the ON SCREEN DISPLAY completely, press the ON SCREEN DISPLAY button twice more after completing step 7 above.
11
How to Use the On Screen Display (OSD)
Geometry window
Rotation, Pincushion, Trapezoid,
Balanced Pincushion, Parallelogram
Follow the steps below to adjust any of the five preset options (ROTATION, PINCUSHION, TRAPEZOID, BALANCED PINCUSHION,
or PARALLELOGRAM). You can make individual adjustments to each of the preset options. Note: use these features only
when the picture is not square.
Press the ON SCREEN
DISPLAY button.
1
2b
Press the ON
SCREEN DISPLAY
button. Then, turn
the ROTARY knob to
adjust the
2a
Turn the ROTARY knob until the GEOMETRY window is
highlighted. Next, press the ON SCREEN DISPLAY button. Then, if
rotation.
necessary, turn the ROTARY knob until ROTATION icon is
highlighted.
2c
When done, press
the ON SCREEN
To select BALANCED PINCUSHION or
PARALLELOGRAM, turn the ROTARY
knob until BALANCED PINCUSHION or
PARALLELOGRAM icon is
highlighted. Next, press the ON
SCREEN DISPLAY button. Then
follow steps 4b and 4c to make
the appropriate changes.
5a
5b
DISPLAY button to
save the change
and return to
GEOMETRY window.
5c
To select
3a
PINCUSHION, turn the
ROTARY knob until
PINCUSHION is
highlighted. Next,
press the ON SCREEN
DISPLAY button.
4c
When done, press the
ON SCREEN DISPLAY button.
This will save the
change and return the
screen to GEOMETRY
window.
When done,
press the ON
SCREEN DISPLAY
button. This will
save the change
and return the
screen to
To select TRAPEZOID,
turn the ROTARY
knob until TRAPEZOID
Icon is highlighted.
Next, press the ON
SCREEN DISPLAY
4a
3b
3c
Turn the ROTARY knob (on
the lower right-hand corner of
the monitor) to adjust the
pincushion.
4b
Turn the ROTARY knob to
adjust the trapezoid.
button.
GEOMETRY
window.
Smart Help
To exit GEOMETRY CONTROLS . . .
. . . but continue to another window, press the ON SCREEN DISPLAY button when “SAVE” is highlighted. Next, turn the ROTARY knob until the desired window
– for example – SIZE & POSITION – is highlighted. Now, turn to SIZE & POSITION On the next page and follow the instructions, starting with step 2.
. . . completely, press the ON SCREEN DISPLAY button twice. The On Screen Display disappears. All changes will be saved.
To make changes to one item, follow the steps for that item. Then, follow “To exit GEOMETRY CONTROLS . . . .”
To return to factory presets, see “To Reset the OSD” on page 15.
12
How to Use the On Screen Display (OSD)
Size & Position window
Horizontal
Zoom
Position
HORIZONTAL POSITION shifts the image on your screen either to the
left or right. Use this feature if your image does not appear
centered.
ZOOM allows you to adjust the image on your screen, both
enlarging it and reducing its overall size. To zoom your screen
in or out, follow the steps below.
Press the ON SCREEN
DISPLAY button.
Press the ON SCREEN
DISPLAY button.
1
1
2
2
Turn the ROTARY knob
until SIZE & POSITION
window is
Turn the ROTARY knob
until SIZE & POSITION
window is
highlighted. Next,
press the ON SCREEN
DISPLAY button. Then,
turn the ROTARY knob
until HORIZONTAL
POSITION is
highlighted. Next,
press the ON SCREEN
DISPLAY button.
highlighted.
6
Press the ON
SCREEN DISPLAY
button to add your
change and return to
the Main Menu.
Press the ON
6
SCREEN DISPLAY
button to add your
change and return to
the Main Menu.
Press again to exit.
See below for other
options.
Press again to exit.
See below for other
3
Press the ON
3
Press the ON
options.
SCREEN DISPLAY
button to bring up
ZOOM screen.
SCREEN DISPLAY
button to bring up
HORIZONTAL POSITION
screen.
5
5
4
4
Turn the ROTARY knob to
adjust the horizontal
position. Note: the screen shifts
left or right as you turn the
ROTARY knob.
Turn the ROTARY knob to
When you
When you
adjust the zoom. Note: the
screen expands or contracts as
you adjust the ROTARY knob.
are done,
press the ON
SCREEN DISPLAY
button.
are done,
press the ON
SCREEN DISPLAY
button.
Smart Help
Smart Help
To make other changes in the SIZE & POSITION window . . .
To make other changes in the SIZE & POSITION window . . .
. . . after returning to the SIZE & POSITION window [but before press the
On Screen Display (OSD) button in step 6], turn the ROTARY knob until
another feature – for example, HORIZONTAL POSITION – is highlighted.
Next, follow steps 2 - 6 under HORIZONTAL POSITION.
. . . after returning to the SIZE & POSITION window [but before press the
On Screen Display (OSD) button in step 6], turn the ROTARY knob until
another feature – for example, HORIZONTAL SIZE – is highlighted. Next,
follow steps 2 - 6 under HORIZONTAL SIZE.
. . . after you have exited completely, press the OSD button and follow
the steps under that feature, for example, HORIZONTAL POSITION.
. . . after you have exited completely, press the OSD button and follow
the steps under that feature, for example, HORIZONTAL SIZE.
13
How to Use the On Screen Display (OSD)
Size & Position window
Horizontal
Size
Vertical Position
Vertical Size
HORIZONTAL SIZE expands or contracts the image on your screen,
pushing it out toward the left and right sides or pulling it in
toward the center.
VERTICAL POSITION adjusts the image on your screen
either up or down. Use this feature if your image does
not appear centered. VERTICAL SIZE expands or contracts the image on
your screen, pushing it out toward the top and bottom of pulling it in
toward the center.
Press the ON SCREEN
DISPLAY button.
Press the ON SCREEN
DISPLAY button.
1
1
2
2
Turn the ROTARY knob
until SIZE & POSITION
window is
highlighted. Next,
press the ON SCREEN
DISPLAY button. Then,
turn the ROTARY knob
until HORIZONTAL SIZE is
highlighted.
Turn the ROTARY knob
until SIZE & POSITION
window is highlighted.
Next, press the ON
SCREEN DISPLAY button.
Then, turn the ROTARY
knob until VERTICAL
POSITION or VERTICAL SIZE
is highlighted.
6
Press the ON
SCREEN DISPLAY
Press the ON
6
SCREEN DISPLAY
button to add your
button to add your
change and return to
the Main Menu.
Press again to exit.
See below for other
options.
change and return to
the Main Menu.
Press again to exit.
See below for other
options.
Press the ON
3
SCREEN DISPLAY
button to bring up
the HORIZONTAL SIZE
screen.
Press the ON SCREEN
DISPLAY button to bring
up the VERTICAL
3
POSITION or VERTICAL
SIZE screen.
4
Turn the ROTARY knob to
adjust the horizontal size.
Note: the screen expands or
contracts as you turn the ROTARY
knob.
When you
When you
5
press the
ON SCREEN
DISPLAY button.
5
are done,
press the ON
SCREEN DISPLAY
button.
are done,
4
Turn the ROTARY knob until
the image is vertically
balanced or the vertical size you
want.
Smart Help
Smart Help
To make other changes in the SIZE & POSITION window . . .
To make other changes in the Main Menu . . .
. . . after returning to the SIZE & POSITION window [but before press the
On Screen Display (OSD) button in step 6], turn the ROTARY knob until
another feature – for example, VERTICAL POSITION – is highlighted. Next,
follow steps 2 - 6 under VERTICAL POSITION.
. . . after returning to the Main Menu [but before press the On Screen
Display (OSD) button a second time in step 6], turn the ROTARY knob
until another feature is highlighted. Next, turn to the page for that
feature and follow the steps.
. . . after you have exited completely, press the OSD button and follow
the steps under that feature, for example, VERTICAL POSITION.
. . . after you have exited completely, press the OSD button and follow
the steps under that feature.
14
How to Use the On Screen Display (OSD)
Save, Cancel, EXIT OSD, AND RESET
Exit OSD & Reset
from the OSD
Save & Recall
From a window
There are three ways to save your changes: by pressing the Front
Panel Button, by selecting SAVE from the On Screen Display, or by
letting the On Screen Display time out. Each method saves the
changes you have made in a particular window.
Exiting from the On Screen Display removes the On Screen Display
from the monitor screen. Resetting from the On Screen Display returns
everything in all the windows to factory presets.
To Exit the entire On Screen Display
1
For example, to make a change in the brightness, press the
1
When you have finished work in any of the windows of the Main
Menu (even selecting MUTE ON / MUTE OFF), you will return to the Main
BRIGHTNESS button on the front panel, make your change, then press
the BRIGHTNESS button again. (See page 4 for details.) You can also let
the display time out and the change will be saved. Note: Brightness,
Contrast, and Volume do not have
Menu and EXIT OSD will be
highlighted. To exit, simply
press the ON SCREEN DISPLAY
button.
a SAVE menu selection.
To cancel a change made in the
You can, however, use the
ROTARY knob and scroll to
another menu item, for
example, ADVANCED CONTROLS. When ADVANCED CONTROLS is
highlighted, press the ON SCREEN DISPLAY button and that
window will replace the Main
Menu. You can now make
Brightness, Contrast, and Volume
windows individually, you must reenter each window and change the
setting.
changes in that window. When
done, you will, again, return to
the Main Menu and EXIT OSD
will be highlighted
2
In some windows (SIZE & POSITION and GEOMETRY), you can save
all your changes at once. In the SIZE & POSITION window, you can
make changes to each of the five items. When you are done,
highlight the SAVE item and press the ON SCREEN DISPLAY button. (See
pages 13 - 14 for details.) You can also let the display time out and
the change will be saved.
To cancel a change made in
the SIZE & POSITION window,
you can select CANCEL from
the On Screen Display. If you
Reset Entire On Screen Display
have made a change to only
1
Selecting RESET from
the Main Menu resets all
one item – for example, ZOOM – then only ZOOM will be changed back
to the previous setting. If more than one item has been changed, but
not saved individually, then all the items changed will be returned to
their previous settings. For example, if you made changes to ZOOM,
HORIZONTAL SIZE, and VERTICAL POSITION and did not save them
individually, all three will be changed back when you select Cancel.
the changes you have made
in all the windows of the
Main Menu. For example, if
the language (See LANGUAGE,
page 7.) has been changed,
it is taken back to English.
Use this feature only when you want to return all your
changes back to their original settings.
Exiting Brightness,
Volume, & Contrast
3
In some windows (ADVANCED CONTROLS AND COLOR TEMPERATURE),
only individual saves are possible. For example, in the COLOR
TEMPERATURE window, if you select USER 1 and make changes (See
page 11 for details.), you must either save or cancel those changes
before moving on. While you could wait for the USER 1 window
(below) to time out, it is not recommended. Since you have not
formally saved this change as your selection, the next time you go
into the COLOR TEMPERATURE window, the screen will change to
selection (USER 1, USER 2, 9300˚ K, or 6500˚ K) last stored by using
SAVE. A checkmark
If you push the VOLUME, BRIGHTNESS, or CONTRAST button to exit (See steps
3 on pages 4 and 5.) and find yourself in the Main Menu, follow the
steps below.
1
Turn the ROTARY
knob until Exit OSD is
selected, then press
the On Screen Display
button.
appears beside that
selection.
To cancel a change made
in COLOR TEMPERATURE (or
ADVANCED CONTROLS), select CANCEL from the on screen display. Only
the last item changed will be changed back. All other items will
remain unchanged.
2
Always exit the VOLUME, BRIGHTNESS, or CONTRAST On Screen
Displays by pressing the VOLUME, BRIGHTNESS, or CONTRAST button
(steps 3 on pages 4 and 5).
ADDITIONAL HOOK UP OPTIONS
AUDIO AND USB SET UPS
Microphone and
Earphones jacks
Microphone and
Audio-in jacks
In addition to built-in speakers and microphone, you can connect this
monitor to optional earphones and a microphone. The jacks are on
the left side of the monitor.
A microphone jack is on the back of the monitor. Use it and the
supplied cable to connect your monitor to your computer or an
amplifier (if either has the right type of jack).
To use the microphone with your computer or an amplifier, make the
connections shown below.
On the back of this monitor there is also an audio-in jack. Use it and
the supplied cable to connect your monitor to your computer or an
amplifier (if either has the right type of jack).
Note: When the earphones are plugged in, there will be no sound
from the built-in speakers.
See page 2 for more detailed illustrations of the jacks’ locations.
Refer to the owner’s manuals included with your earphones and microphone for a detailed guide to setting up these items.
(Optional)
USB
Connections
USB (Universal Serial Bus) is an innovation in connecting your IBM-compatible computer to your monitor. By using the USB, you will be able to connect
your keyboard, mouse, printer, and other peripherals to your monitor instead of having to connect them to your computer. This will give you greater
flexibility in setting up your system. Plus, you will have true plug-and-play capability. While the software is still being developed, Philips has included
the hardware so you will be ready to take advantage of this next generation in computer development.
For an IBM-compatible Computer:
1. Turn off the computer.
2.. Connect the (optional) USB Hub and cable to the
computer and to the monitor. (Computer must
have a USB port.)
3. Connect the power cable.j
4. Turn on the monitor. Then turn on the computer.
5. With the installation of the correct software, you
will be able to connect specially-made
peripherals to the monitor.
Refer to the “Setting Up your Philips monitor” foldout for a more detailed guide to setting up your monitor.
16
17
Additional Information
Power saving feature / Glossary
Automatic Power Savings &
Preset Resolution Modes
If you have VESA's DPMS compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when
not in use. If input from a keyboard, mouse, or other device is detected, the monitor automatically “wakes up.” The table at left shows the power
consumption and signalling of this automatic power-saving feature. To turn this feature on and off, see page 7. The table at right shows the 8 factory
preset resolution modes. The maximum number of modes is 12 This leaves room for additions.
Factory Preset Resolution Modes
Power Management Definition
VESA's mode Video
H-sync
V-sync
Power
used
Power
LED
MODE RESOLUTION
H. FREQ.
(KHZ)
V. FREQ.
(HZ)
STANDARD
saving(%) color
1
2
3
4
5
6
7
8
640 x 400
640 x 480
640 x 480
800 x 600
800 x 600
1024 x 768
1024 x 768
1280 x 1024
31.5
31.5
43.3
46.9
53.7
60
70
60
85
75
85
75
85
60
VGA
VGA
ON
Active
Yes
No
Yes
Yes
No
< 100W
< 15W
< 15W
0%
Green
Yellow
Yellow
Amber
Stand-by
Suspend
OFF
Blanked
Blanked
Blanked
86%
86%
95%
Yes
No
VESA/85
VESA/75
VESA/85
VESA/75
VESA/85
VESA/60
No
<
5W
This monitor is Energy Star compliant and power management compatible.
68.7
64
AS AN ENERGY STAR PARTNER, PHILIPS HAS DETERMINED THAT THIS
PRODUCT MEETS THE ENERGY STAR GUIDELINES FOR ENERGY EFFICIENCY.
The proper operation of the function requires a computer with VESA DPMS
power management capabilities. When used with a computer equipped with
VESA DPMS, the monitor is Energy Star compliant.
Glossary
Here are a few definitions that may help you.
Brightness
Refers to how light or dark the overall screen is.
Color
Temperature
A term used to refer to the color balance, uniformity, and saturation settings on your monitor screen. Color (even white,
gray, and black) on your screen is achieved by blending (or balancing) three primary colors: red, green, and blue. As you
increase or decrease any one of these colors, the color temperature changes. For example, at 9300˚ K, you are using more
blue in your color temperature; therefore, your screen will be saturated with more blue and should appear uniformly “bluer”
from one side of the screen to the other. At 6500˚ K, you are using more red in your mixture. True color balance is achieved
when a gray object shows no traces of either red, green, or blue, regardless of the brightness of the image.
Contrast
Degauss
DDC
Refers to the sharpness of objects on the screen and the ability to easily distinguish one from the other.
The process by which metal parts of the screen are demagnetized in order to reduce screen distortion and color impurity.
(Display Data Channel) is a signaling standard established to help the performance of personal computers. In order to
use this function, your computer must be designed for DDC. There are several types of DDC. Most computer monitors
are designed for DDC1 and DDC2 Level B (DDC1 /2B).
Geometry
A set of controls that allows you to adjust the alignment of the picture on the monitor screen. The goal is to “square up”
the picture. This is done by adjusting such items as balanced pincushion, pincushion, parallelogram, rotation, and
trapezoid.
Moire
Noise
USB
A fringe pattern caused by the interference between two superimposed line patterns.
Term used to refer to interference with the monitor’s picture.
Universal Serial Bus. A way to connect your IBM-compatible computer, monitor, and peripherals for true Plug-and-Play
functions. This is an emerging technology.
17
Additional information
Coming to Terms with this Book
Specifications
Index
6500˚ K . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
9300˚ K . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Audio Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Audio in jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2, 16
Automatic Power Saving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Balanced Pincushion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Built-in microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Cable Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Cancel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Color Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3, 10 -11
Contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
DDC1 / 2B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Degauss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Description of controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2, 3
DTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Earphones jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2, 16
End-of-life disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Exit OSD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Geometry Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3, 12
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Hook Ups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Set Up Guide, 16
Horizontal Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Horizontal Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Main Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3, 4-5
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Microphone jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2, 16
Moire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Monitor cable plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Monitor Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3, 5
On Screen Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
OSD button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Parallelogram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Pedestal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Pin Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Pincushion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Power button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Set Up Guide, 2
Power plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Set Up Guide, 2
Power Saving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Resolution Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Rotary knob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Save . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Size & Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3, 13 - 14
Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Sync Input Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Trapezoid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . Set Up Guide, 19
USB hub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2, 16
USB set up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
User 1, User 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Vertical Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Vertical Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Video Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Warranty (Appendix) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
GENERAL
CRT
Screen size
Viewable Image Size (VIS)
Dot pitch
Phosphor
:15" (38.1 cm) flat & square
:13.8"
:0.28 mm (horizontal)
:P22 or equivalent, medium short
persistence
Screen treatment
:Anit-glare, anti-static
Display area
Factory preset
Maximum usable
Scanning frequency
Horizontal (line)
Vertical (frame)
Input power
Power consumption
Thermal dissipation
:270 mm (H) x 202 mm (V)
:280 mm (H) x 210 mm (V)
:30-70kHz (AutoScan)
:50-160 Hz (AutoScan)
:100 - 240 V AC, 50 - 60 Hz
:75 Watt normal, 100Watt max.
:238.9 BTU normal,
341.3 BTU maximum
Input signal
Video
Sync
:0.7 Vpp, 75 Ohm impedance
:Separate sync. TTL
Composite sync. TTL level
Sync on green video
Pedestal
Tilt
Swivel
Physical
Unit dimension (WxHxD)
:5° forward, 11° backward
:90° left, 90° right
:382 x 392 x 424 mm
(15.04" x 15.43" x 16.69")
:14.0 kg (39.6 lbs.)
Net weight
Operating conditions
Temperature
Humidity
Storage conditions
Temperature
:0° C - 40° C
:10% - 90%
:-25° C - 65° C
:5% - 95%
Humidity
Specifications subject to change without notification.
Pin Assignment
The 15-pin D-sub connector (male) of the signal cable:
Pin No. Assignment
1
2
3
4
Red video input
Green video input
Blue video input
Identical output
- connected to pin 10
5
6
7
8
9
Self test
Red video ground
Green video ground
Blue video ground
No pin
10 Logic ground
11 Identical output
- connected to pin 10
12 Serial data line (SDA)
13 H. Sync / H+V
14 V. Sync (VCLK for DDC)
15 Data clock line (SCL)
18
Additional Information
What to do if Something isn’t Working
Troubleshooting
Having trouble? Something not working? Before calling for help, try these suggestions.
HAVING THIS PROBLEM?
No Picture
(Power LED not lit)
CHECK THESE ITEMS
Make sure the Power cable is plugged in the wall and back of the monitor.
Power button on top of the monitor should be in the ON position.
Disconnect the monitor from the power outlet for about one minute.
No Picture
Make sure the computer is turned on.
(Power LED is Amber
or Yellow)
Make sure the monitor cable is properly connected to your computer.
Check to see if the monitor cable has bent pins.
The Energy Saving Feature may be activated. See pages 7 and 17 for details.
No Picture
(Power LED is Green)
Make sure the Brightness and Contrast controls are set correctly. See page 4 for details
Make sure the monitor cable is properly connected to your computer.
Check to see if the monitor cable has bent pins.
Make sure the computer Power button is on.
Screen shows
Make sure the monitor cable is properly connected to your computer. See Setting Up Guide.
Check to see if the monitor cable has bent pins.
Make sure the computer is turned on
NO SYNC INPUT
when you turn on
the monitor.
No Color or intermittent
Black-and-White
If you are using a non-VESA-DDC standard video card, turn the DDC1 / 2B feature Off. See page 8.
Color appears blotchy
The picture may need degaussing. See page 6 for details.
Remove any nearby magnetic objects.
Face the monitor East for best picture quality.
Missing one or
more colors
Check user settings of Color Temperature. See pages 10 and 11 for details.
Make sure the monitor cable is properly connected to your computer.
Check to see if the monitor cable has bent pins.
Adjust Sync Input Select. See page 9 for details.
Dim Picture
Adjust the Brightness and Contrast controls. See page 4 for details.
Check your video card and the manual instructions for it. It may be a non-VESA-DDC Standard card.
Adjust Sync Input Select. See page 9 for details.
Picture is too large
or too small
Adjust the Horizontal and/or Vertical Size. See pages 13 and 14 for details.
Adjust the Zoom. See page 13 for details.
Edges of the picture
are not square
The geometry controls require adjusting. See page 12 for details.
Picture has a double
image
Eliminate the use of a video extension cable and/or video switch box.
Face the monitor East for best picture quality.
Picture is not sharp
Check to make sure Moire is switched off. See page 9.
Adjust Sync Input Select. See page 9 for details.
No Audio
Make sure mute is not activated. See page 5 for details.
Make sure the Audio-in cable is securely plugged into the monitor and the audio source.
See pages 2 and 16 for details.
Unstable Picture
Increase your refresh rate. Consult your computer manual for details.
Windows ’95 cannot
find your video card
Select “Super VGA” under STANDARD DISPLAY TYPES, or contact your video card manufacturer
for the right drivers.
For further assistance, contact Philips at (800) 835-3506 or (423) 475-0280.
19
|