Philips 13PR19C1 User Manual

Color Television

13PR19C1

Instructions for use

3135 015 10361

SAFETY INSTRUCTIONS - Read before operating equipment

This product was designed and manufactured to meet strict quality and

safety standards. There are, however, some installation and operation pre-

cautions which you should be particularly aware of.

11. Power-Cord Protection - Power supply cords should be routed so

that they are not likely to be walked on or pinched by items placed

upon or against them, paying particular attention to cords and plugs,

convenience receptacles, and the point where they exit from the

appliance.

1. Read Instructions - All the safety and operating instructions should

be read before the appliance is operated.

12. Cleaning - The appliance should be cleaned only as recommended

2. Retain Instructions - The safety and operating instructions should

by the manufacturer.

be retained for future reference.

13. Power Lines - An outdoor antenna should be located away from

3. Heed Warnings - All warnings on the appliance and in the operating

power lines.

instructions should be adhered to.

14. Outdoor Antenna Grounding - If an outside antenna is connected to

the receiver, be sure the antenna system is grounded so as to pro-

vide some protection against voltage surges and built up static

charges.

4. Follow Instructions - All operating and use instructions should be

followed.

5. Water and Moisture - The appliance should not be used near water

- for example, near a bathtub, washbowl, kitchen sink, laundry tub,

in a wet basement or near a swimming pool, etc.

Section 810 of the National Electric Code, ANSI/NFPA No. 70-1984,

provides information with respect to proper grounding of the mats

and supporting structure grounding of the lead-in wire to an anten-

na discharge unit, size of grounding connectors, location of antenna-

discharge unit, connection to grounding electrodes and require-

ments for the grounding electrode. See Fig. below.

6. Carts and Stands - The appliance should be used only with a cart or

stand that is recommended by the manufacturer.

6A.

An appliance and cart combination should be moved

with care. Quick stops, excessive force, and uneven sur-

faces may cause the appliance and cart combination to

overturn.

15. Non-use Periods - The power cord of the appliance should be

unplugged from the outlet when left unused for a long period of time.

16. Object and Liquid Entry - Care should be taken so that objects do not

6B. Tilt/Stability - All televisions must comply with recommended inter-

national global safety standards for tilt and stability properties of its

cabinet design.

fall and liquids are not spilled into the enclosure through openings.

17. Damage Requiring Service - The appliance should be serviced by

•

Do not compromise these design standards by applying exces-

sive pull force to the front, or top, of the cabinet which could

ultimately overturn the product.

Also, do not endanger yourself, or children, by placing elec-

tronic equipment/toys on the top of the cabinet. Such items

could unsuspectingly fall from the top of the set and cause

product damage and/or personal injury.

qualified service personnel when:

A. The power supply cord or the plug has been damaged; or

B. Objects have fallen, or liquid has been spilled into the appliance;

•

C. The appliance has been exposed to rain; or

D. The appliance does not appear to operate normally or exhibits a

marked change in performance; or

7. Wall or Ceiling Mounting - The appliance should be mounted to a

E. The appliance has been dropped, or the enclosure damaged.

wall or ceiling only as recommended by the manufacturer.

18. Servicing - The user should not attempt to service the appliance

beyond that described in the operating instructions. All other servic-

ing should be referred to qualified service personnel.

8. Ventilation - The appliance should be situated so that its location or

position does not interfere with its proper ventilation. For example,

the appliance should not be situated on a bed, sofa, rug, or similar

surface that may block the ventilation openings; or, placed in a built-

in installation, such as a bookcase or cabinet that may impede the

flow of air through the ventilation openings.

9. Heat - The appliance should be situated away from heat sources

such as radiators, heat registers, stoves, or other appliances (includ-

ing amplifiers) that produce heat.

Note to the CATV system installer: This reminder is provided to call the

CATV system installer's attention to Article 820-40 of the NEC that pro-

vides guidelines for proper grounding and, in particular, specifies that the

cable ground shall be connected to the grounding system of the building,

as close to the point of cable entry as practical.

10. Power Sources - The appliance should be connected to a power sup-

ply only of the type described in the operating instructions or as

marked on the appliance.

Example of Antenna Grounding

as per NEC - National Electric Code

GROUND CLAMP

ANTENNA LEAD IN WIRE

ANTENNA DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM

(NEC ART 250, PART H)

ELECTRIC SERVICE EQUIPMENT

TABLE OF CONTENTS

Introduction

Here are a few of the special features built into this

new Color Television:

Welcome/Registration of Your TV ............................2

Safety/Precautions .....................................................3

Table of Contents.......................................................4

Features......................................................................4

Basic Cable TV Hookups ..........................................5

Basic Antenna Hookups.............................................6

Basic TV to VCR Hookup.........................................7

Basic TV and Remote Operations .............................8

TV Remote Buttons ...................................................9

SmartLock™ feature allows you to block the view-

ing of certain channel or external audio/video con-

nections where you might not want your children

viewing inappropriate material.

Infrared Remote Control works your TV set.

Standard broadcast (VHF/UHF) or Cable TV

(CATV) channel capability.

Closed Captioning allows the viewer to read TV

program dialogue or voice conversations as onscreen

text.

Onscreen MENU

✧ Setting the Language Control.................10

✧ Using the Tuner Control...................................11

✧ Using the Auto Program Control .....................12

✧ How to Add and Delete Channels....................13

✧ Using the External Control (Input Naming)....14

✧ Adjusting the TV Picture .................................15

✧ Activating Contrast Plus (Black Stretch).........16

✧ Activating Noise Reduction (Picture) Control 17

✧ Setting the TV’s Clock.....................................18

✧ Activating the Timer Control...........................19

✧ Activating the Start-Up Channel .....................20

✧ Setting the TV’s Start Time Control................21

✧ Setting the TV for Closed Caption ..................22

✧ Using the Sleep Timer Control........................23

Automatic Programming of Channels for quick

and easy selection of favorite stations available in

your area.

Onscreen Features (in either English, French, or

Spanish) show helpful messages for setting of TV

controls.

Sleeptimer automatically turns the TV OFF at preset

times.

SmartPicture™ allows you to set the picture color,

tint, contrast, etc. for various types of programming

such as Personal (picture controls the way you set

them), Sports, Movies, or Weak Signals with the push

of one button.

SmartLock™

✧ Understanding the SmartLock Feature.......24

✧ Setting the SmartLock Access Code................25

✧ Setting the SmartLock to Block Channels.......26

✧ Setting SmartLock’s Blocking Options ...........27

✧ Blocking Using the Movie/TV Ratings .....28-29

✧ Using the SmartLock Review Screen..............30

SmartSound™ controls allow you to set the sound

controls for various types of listening programs such

as Personal (sound controls the way you set them),

Theater, Music, or Voice with the push of one button.

Sound

✧ Using the Treble Boost and

Bass Boost controls..........................................31

✧ Using the Volume Bar Control ........................31

✧ Using the Input control and

the Audio/Video Input Jacks............................32

NOTE: This owner's manual is used with sev-

eral different television models. Not all fea-

tures (and drawings) discussed in this manual

will necessarily match those found with your

television system. This is normal and does not

require you contacting your dealer or request-

ing service.

Remote Control Operation

Using the SmartPicture™ Control................33

Using the SmartSound™ (AVL) Control......34

Using SmartSurf™ (Alternate Channel) .................35

General Information

Tips if Something Isn’t Working ................36

Glossary of TV Terms..............................................37

Index ........................................................................37

Factory Service Locations..................................38-39

Warranty...................................................................40

SmartPicture™, SmartSound™, SmartSurf™, and SmartLock™ are all

registered trademarks of Philips Consumer Electronics Company.

HOOKING UP YOUR TV (BASIC CABLE TV CONNECTIONS)

SMART

CABLE TV

HELP

our Cable TV input into your

Yhome may be a single (75

ohm) cable, or a Converter Box

installation. In either case the

connection to the TV is very easy.

Just put the threaded end of the

cable signal to the TV's antenna

plug and screw it down tight.

BEGIN

Remember:

Set the TV for the

type signal you've

just connected (see

the “Tuner” section

on page 11 of this

manual.)

To select only the

channel numbers on

your Cable system

see “Auto Program"

(page 12). If you use

a Cable Converter

box, set the TV to the

same channel as the

converter's CH 3/4

switch (on the rear of

the converter.)

If your Cable TV signal is a sin-

gle round cable (75 ohm) then

you're ready to connect to the TV.

If you have a Cable Converter

Box:

Connect the Cable TV signal to the

Cable Signal IN(put) plug on the

Converter..

⍀

Connect the Cable TV cable to the

75Ω plug on the TV.

If you have a Cable Converter Box:

Connect the OUT(put) plug from the

Converter to the 75Ω plug on the TV.

Cable TV Company

Cable TV Signal Input

VIDEO

AUDIO

75 ⍀

OUT

Round Cable

75Ω Ohm

Back of TV

Cable TV Converter

Box Connection

HOOKING UP YOUR TV (BASIC ANTENNA TV CONNECTIONS)

SMART

ANTENNA

HELP

combination antenna receives

Anormal broadcast channels

(VHF 2-13 and UHF 14-69).

Your connection is easy since

there is only one 75Ω (ohm)

antenna plug on the back of your

TV - and that’s where the antenna

goes.

Remember:

Be sure to set the

TV for the type sig-

nal you've connect-

ed (see the “Tuner”

section on page 11

of this manual.)

Note: For homes with separate UHF and VHF antennas

you will need an optional combiner to connect to the TV.

U/V

Combiner

BEGIN

To set the TV to

select only the chan-

nel numbers in your

area see how to

“Program" or "Add"

channels in the TV’s

memory on page 12

(Auto Program sec-

tion).

If your antenna has a round

cable (75 ohm) on the end, then

you're ready to connect it to the TV.

If your antenna has flat twin-lead

wire (300 ohm), you first need to

attach the antenna wires to the screws

on a 300 to 75 ohm adapter.

⍀

Back of TV

75-300 Ohm Adapter

Push the round end of the adapter

(or antenna) onto the 75Ω plug

on the rear of the TV. If the round

end of the antenna wire is threaded,

screw it down tight.

To order any option-

al accessory contact

your dealer or the

Philips Parts Center

at 1-800-851-8885.

⍀

Combination VHF/UHF

Antenna

(Outdoor or Indoor)

300 to 75Ω

Adapter

VIDEO

Twin Lead

Wire

AUDIO

75 ⍀

Round Cable

75Ω

Back of TV

HOOKING UP YOUR TV (BASIC TV TO VCR CONNECTIONS)

TV TO VCR

he basic Antenna, or Cable

TTV, to VCR to TV connection

is shown to the right. For more

information on other hookups

(possible when Cable

Converter/Descrambler boxes are

included) refer to your accessory

VCR and Cable Converter

Owner's Manual for details.

BEGIN

Connect your Antenna or Cable

TV signal to the IN FROM

ANT(enna) plug on the VCR.

Connect the OUT TO TV plug

on the VCR to the 75Ω plug on the

TV (connecting cable supplied with

the VCR.)

⍀

Outdoor

VHF/UHF

Antenna

300 to 75Ω

Ohm Adapter

OUT TO TV

IN FROM ANT.

VIDEO

AUDIO

75 ⍀

Cable TV signal

VCR

Back of TV

Round Cable

75Ω Supplied with VCR

BASIC TV/REMOTE OPERATIONS

TELEVISION

BEGIN

Press the POWER button to

turn the TV ON.

Press the VOLUME + button to

increase the sound level or the

VOLUME – button to lower the

sound level.

The Front Audio/Video Input Jacks

make it real easy to watch the playback

of a video tape using a camcorder

(or any accessory device) with

Audio/Video Output Jacks.

Pressing both buttons at the same

time will display the onscreen menu.

Once in the menu, use these button

to make adjustments or selections.

VIDEO

AUDIO

–

LUME

POWER

Remote Sensor Window

Press the CHANNEL UP ▲ or

DOWN ▼ button to select TV chan-

nels.

Front Audio/Video Inputs (Mono)

VIDEO

AUDIO

–

VOLUME +

CHANNEL

POWER

REMOTE

BATTERY INSTALLATION

o load the supplied batteries

Tinto the remote:

1. Remove the battery compart-

ment lid on the back of the remote.

POWER

SLEEP

CLOCK

2. Place the batteries (2-AA) in

the remote. Be sure the (+) and (-)

ends of the batteries line up correctly

(inside of case is marked.)

Point the remote control

toward the remote sensor

window on the TV when

operating the TV with the

remote.

SURF

TUS

EXIT

A/CH

MUTE

SMAR

VOL

SMAR

PICTURE

SOUND

3. Reattach the battery lid.

SMART HELP

Remember,

You can press

The tuned channel

number will always

You can also press the

STATUS/EXIT button

any button on the front

of the TV to turn the

TV ON.

briefly appear when the (on the remote) to see

TV is first turned ON

(and with channel

changes.)

what channel the TV is

ON.

TV REMOTE BUTTONS

Power Button

Press to turn the TV ON and OFF.

POWER

SLEEP

Sleep Button

Press to set the TV to automatically turn itself OFF.

CC Button

Press to select Closed Caption options within the menu.

CLOCK

Clock Button

Press for direct entry of the TIMER (Clock) features were you can set

the TV’s clock, the Start Time, and the Start Channel Controls.

Number Buttons

Press the number buttons to select TV channels. For single digit entries,

press the number of the channel you desire. The TV will pause for a few

seconds, then change to the selected channel. For channels 100 and

above, press "1" then the next two numbers. (Example, Press "1", then

"2", then "5" for channel 125.)

A/CH Button

Press to toggle between the currently viewed channel and the previously

viewed channel.

A/CH

SURF

Surf Button

STATUS

Press to select previously viewed channels. You can place up to 8 channels

in memory. Then by pressing the SURF button you can quickly view the

select channels. See the “Surf" section to see how to select a series of

channels using the Surf button.

EXIT

Menu Button

Press for the onscreen menu to appear. Pressing the menu button after

menu selections are made will eliminate the menu from the display.

Status/Exit Button

Press to see the current channel number on the TV screen. Also press to

clear the TV screen after control adjustments.

Cursor Buttons

Use these button to select and adjust the TV's onscreen menu.

VOL

Volume (+), (–) Buttons

Press to adjust the TV sound level.

MUTE

SMART

Mute Button

Press to turn the sound OFF on the TV. Press again to return the

sound to its previous level.

SOUND PICTURE

Smart Sound Button

Press to select from a list of Smart Sound controls. (Factory preset

sound control levels set for different types of listening sources and

programs.)

Smart Picture Button

Press to select from a list of Smart Picture controls. (Factory preset

picture control levels set for different types of viewing sources and

programs.)

Channel (+), (–) Buttons

Press to change the tuned channel.

USING THE LANGUAGE CONTROL

or our Spanish and French speak-

Fing TV owners an onscreen LAN-

GUAGE option is present. With the

LANGUAGE control you can set the

TV’s onscreen menu to be shown in

either English, Spanish, or French.

BEGIN

Press the MENU button on the

remote to show the onscreen menu.

ᮣ

CLOCK

OFF

ᮣ

Press the CURSOR UP ▲ or

DOWN ▼ buttons to scroll through

the onscreen menu until the word

SETUP is highlighted.

SETUP

ᮣ

SmartLock REVIEW

BRIGHTNESS

LANGUAGE

TUNER

ENGLISH

CABLE

ᮣ

AUTO PROGRAM

Press the CURSOR RIGHT ᮣ

button to display the SETUP menu

features.

POWER

LANGUAGE

FRANCAIS

ESPANOL

Press CURSOR UP ▲ or

DOWN ▼ buttons to scroll the

Setup features until the word LAN-

GUAGE is highlighted.

CLOCK

SLEEP

Press the CURSOR RIGHT ᮣ

button repeatedly to select ENG-

LISH, ESPANOL (Spanish), or

FRANCAIS (French).

A/CH

SURF

STATUS

EXIT

VOL

MUTE

SMART

SMART HELP

SOUND PICTURE

Remember: The Language

control only makes the TV’s

onscreen MENU items appear in

English, Spanish, or French text.

It does not change the other onscreen

text features such as Closed Caption

(CC) TV shows.

The onscreen menu will time out and

disappear from the screen when you

finish, or you can press the STA-

TUS/EXIT button to clear the menu

from the screen.

USING THE TUNER CONTROL

he TUNER feature allows you to

Tchange the TV’s signal input to

either CABLE, AUTO or ANTENNA

mode. It’s important for the TV to

know what type of signal to look for.

(From a Cable TV signal or a nor-

mal Antenna signal.) In the AUTO

mode, when the AUTO PROGRAM

feature is activated, the TV will auto-

matically choose the correct mode.

ᮣ

CLOCK

OFF

ᮣ

BEGIN

SETUP

Press the MENU button on the

remote to show the onscreen menu.

ᮣ

SmartLock REVIEW

BRIGHTNESS

LANGUAGE

TUNER

ENGLISH

CABLE

ᮣ

Press the CURSOR UP ▲ or

DOWN ▼ buttons to scroll through

the onscreen menu until the word

SETUP is highlighted.

AUTO PROGRAM

CHANNEL EDIT

ᮣ

POWER

TUNER

AUTO

Press the CURSOR RIGHT ᮣ

button to display the SETUP menu

features.

CLOCK

SLEEP

TUNER

ANTENNA

Press CURSOR UP ▲ or

DOWN ▼ buttons to scroll the

Setup features until the word

TUNER is highlighted.

A/CH

SURF

STATUS

EXIT

Press the CURSOR RIGHT ᮣ

button to select either CABLE,

AUTO or ANTENNA mode.

VOL

MUTE

SMART

SOUND PICTURE

SMART HELP

When CABLE is selected,

channels 1-125 are available.

When ANTENNA is selected, chan-

nels 2-69 are available.

When AUTO is selected, the TV will

automatically set itself to the correct

mode based on the type of signal it

detects when the AUTO PROGRAM

feature is activated.

The onscreen menu will time out and

disappear from the screen when you

finish, or you can press the STA-

TUS/EXIT button to clear the menu

from the screen.

USING THE AUTO PROGRAM CONTROL

our TV can automatically set itself

Yfor local area (or Cable TV) chan-

nels. This makes it easy for you to

select only the TV stations in your

area when the CHANNEL (+), (–) but-

tons are pressed.

Note: Make sure the antenna or cable

signal connection has been completed

before AUTO PROGRAM is used.

ᮣ

CLOCK

OFF

ᮣ

BEGIN

SETUP

LANGUAGE

TUNER

ENGLISH

Press the MENU button on the

remote to show the onscreen menu.

ᮣ

SmartLock REVIEW

BRIGHTNESS

CABLE

ᮣ

AUTO PROGRAM

CHANNEL EDIT

EXTERNAL

ᮣ

Press the CURSOR UP ▲ or

DOWN ▼ buttons to scroll through

the onscreen menu until the word

SETUP is highlighted.

ᮣ

POWER

Press the CURSOR RIGHT ᮣ

button to display the SETUP menu

features.

CLOCK

SLEEP

Press CURSOR UP ▲ or

DOWN ▼ buttons to scroll the

Setup features until the words AUTO

PROGRAM are highlighted.

AUTO PROG

A/CH

SURF

STATUS

EXIT

Press the CURSOR RIGHT ᮣ

button to start the Auto Program

scanning of channels.

Auto Program will scan for

all available channels within

the Antenna/Cable signal.

When finished, the TV will

go back to the SETUP menu.

VOL

MUTE

SMART

SOUND PICTURE

SMART HELP

Try it out. Press the CHAN-

NEL (+), (–) buttons and see

which channels have been added to

the TV’s memory.

If you want to delete any unwanted

channels from the TV’s memory, see the

CHANNEL EDIT section on page 13.

The onscreen menu will time out and

disappear from the screen when you

finish, or you can press the STA-

TUS/EXIT button to clear the menu

from the screen.

HOW TO ADD AND DELETE CHANNELS

hannel Edit makes it easy for you

Cto ADD or DELETE channels

from the list of channels stored in the

TV’s memory.

BEGIN

Press the MENU button on the

remote to show the onscreen menu.

Press the CURSOR UP ▲ or

DOWN ▼ buttons to scroll through

the onscreen menu until the word

SETUP is highlighted.

ᮣ

CLOCK

OFF

ᮣ

SETUP

TUNER

CABLE

ᮣ

SmartLock REVIEW

BRIGHTNESS

AUTO PROGRAM

CHANNEL EDIT

EXTERNAL

Press the CURSOR RIGHT ᮣ

button to display the SETUP menu

features.

ᮣ

Press the CURSOR UP ▲ or

DOWN ▼ buttons to scroll the

Setup features until the words

POWER

CLOCK

SLEEP

CHANNEL EDIT are highlighted.

CHANNEL

Press the CURSOR RIGHT ᮣ

button to display the CHANNEL

EDIT options.

SAVED

YES

CHANNEL ADDED

A/CH

SURF

With the CHANNEL EDIT

options displayed, and the word

CHANNEL highlighted; enter the

channel number (with the NUM-

BERED or the CURSOR ᮣ

RIGHT or LEFT ᮤ buttons) you

wish to ADD to, or DELETE from

the TV’s memory.

STATUS

EXIT

CHANNEL

SAVED

CHANNEL DELETED

VOL

MUTE

SMART

SOUND PICTURE

Scroll down (using the CUR-

SOR UP ▲ or DOWN ▼ buttons)

to highlight the word SAVED.

Now use the CURSOR RIGHT ᮣ

button to toggle between YES or

NO.

If YES is selected the menu reads

“CHANNEL ADDED” and the

channel is added to the TV’s memo-

ry. If NO is selected the menu reads

“CHANNEL DELETED” and the

channel is deleted from the TV’s

memory.

USING THE EXTERNAL CONTROL

he External feature allows you to

Trename your input source selec-

tions. When the Input feature (refer to

Owner’s Manual for details) is

accessed to change audio/video jacks,

your source selection will be called by

the name you choose. This name will

also appear onscreen when using the

audio/video inputs.

ᮣ

CLOCK

BEGIN

OFF

ᮣ

SETUP

ᮣ

Press the MENU button on the

remote to show the onscreen menu.

AUTO PROGRAM

CHANNEL EDIT

EXTERNAL

ᮣ

SmartLock REVIEW

BRIGHTNESS

Press the CURSOR UP ▲ or

DOWN ▼ buttons to scroll through

the onscreen menu until the word

SETUP is highlighted.

POWER

Press the CURSOR RIGHT ᮣ

button to display the SETUP menu

features.

CLOCK

SLEEP

Press the CURSOR UP ▲ or

DOWN ▼ buttons to scroll the

Setup features until the word

EXTERNAL is highlighted.

EXT 1

EXT

A/CH

SURF

STATUS

EXIT

EXT 1

GAM

DVD

VCD

VCR

Press the CURSOR RIGHT ᮣ

button to activate the External fea-

ture.

VOL

With the External options menu

displayed, press the CURSOR

RIGHT ᮣ button to select a name

from the list: EXT, GAM, DVD,

VCD, VCR, LD, or SAT.

MUTE

SMART

SOUND PICTURE

SAT

SMART HELP

Remember: This feature will

rename your external signal

source and appear onscreen with the

new name but does not limit you to

the type of accessory device that you

may use.

The onscreen menu will time out and

disappear from the screen when you

finish, or you can press the STA-

TUS/EXIT button to clear the menu

from the screen.

HOW TO ADJUST THE TV PICTURE

o adjust your TV picture con-

Ttrols, select a channel and follow

BEGIN

the steps shown below:

Press the MENU button on the

remote to display the onscreen menu.

Press the CURSOR UP ▲ or

DOWN ▼ buttons until the

word BRIGHTNESS is highlighted.

(Or, COLOR, PICTURE, SHARP-

NESS, TINT, COL. TEMP depend-

ing on the adjustment you want to

make.)

ᮣ

SETUP

ᮣ

SmartLock REVIEW

BRIGHTNESS

COLOR

ᮣ

SmartLock REVIEW

BRIGHTNESS

COLOR

PICTURE

Press the CURSOR RIGHT ᮣ

or the CURSOR LEFT ᮤ buttons

to increase or decrease the brightness

of the picture.

SHARPNESS

BRIGHTNESS

COLOR

POWER

PICTURE

SHARPNESS

TINT

CLOCK

SLEEP

SMART HELP

BRIGHTNESS Press the ᮣ

or ᮤ buttons until darkest parts of

the picture are as bright as you prefer.

COLOR

A/CH

SURF

PICTURE

SHARPNESS

TINT

STATUS

COLOR Press the ᮣ or ᮤ buttons to

add or eliminate color.

EXIT

PICTURE Press the ᮣ or ᮤ buttons

until lightest parts of the picture show

good detail.

COL TEMP

NORMAL

VOL

SHARPNESS Press the ᮣ or ᮤ buttons

MUTE

PICTURE

SHARPNESS

TINT

to improve detail in the picture.

SMART

TINT Press the ᮣ or ᮤ buttons to

obtain natural skin tones.

SOUND PICTURE

COLOR TEMP Press the ᮣ or ᮤ but-

tons to select NORMAL, COOL, or

WARM picture preferences. (NORMAL

will keep the whites, white; COOL will

make the whites, bluish; and WARM will

make the whites, reddish.)

COL TEMP

NORMAL

OFF

CONTRAST PLUS

SHARPNESS

TINT

The onscreen menu will time out and dis-

appear from the screen when you finish, or

you can press the STATUS/EXIT button to

clear the menu from the screen.

NORMAL

OFF

COL TEMP

CONTRAST PLUS

NOISE REDUCTION

OFF

COL TEMP

WARM

COOL

ACTIVATING THE CONTRAST PLUS (BLACK STRETCH) CONTROL

he Contrast Plus (Black Stretch)

Tfeature helps to “sharpen” the

picture quality. The black portions of

the picture become richer in dark-

ness and the whites become brighter.

BEGIN

Press the MENU button on the

remote to display the onscreen menu.

Press the CURSOR UP

▲

TINT

NORMAL

OFF

CURSOR DOWN ▼ buttons until

the words CONTRAST PLUS are

highlighted.

COL. TEMP

CONTRAST PLUS

TINT

NORMAL

COL. TEMP

CONTRAST PLUS

NOISE REDUCTION

VOLUME

Press the CURSOR RIGHT ᮣ

or CURSOR LEFT ᮤ buttons to

activate or deactivate the Contrast

Plus feature.

NOISE REDUCTION

VOLUME

POWER

CLOCK

SLEEP

SMART HELP

Remember: The onscreen

menu will disappear in a few

seconds after you have finished your

adjustment.

A/CH

SURF

STATUS

EXIT

VOL

MUTE

SMART

SOUND PICTURE

ACTIVATING THE NOISE REDUCTION (PICTURE) CONTROL

or reasons such as poor cable

Freception, the picture can some-

times appear slightly “speckled” (or

signal noise shown in the picture). The

NOISE REDUCTION control can help

eliminate this type of interference and

improve the quality of the picture.

BEGIN

Press the MENU button on the

remote to display the onscreen menu.

COL TEMP

NORMAL

CONTRAST PLUS

Press the CURSOR UP ▲ or

CURSOR DOWN ▼ button until

the words NOISE REDUCTION are

highlighted.

NOISE REDUCTION

VOLUME

OFF

COL TEMP

NORMAL

CONTRAST PLUS

AVL

OFF

NOISE REDUCTION

VOLUME

Press the CURSOR RIGHT ᮣ

or CURSOR LEFT ᮤ buttons to

activate or deactivate the Noise

Reduction Feature.

AVL

OFF

POWER

CLOCK

SLEEP

SMART HELP

Remember: The onscreen

menu will disappear in a few

seconds after you have finished your

adjustment.

A/CH

SURF

STATUS

EXIT

“Noise” Reduction is a video adjust-

ment feature that affects the picture

quality of the TV not the sound.

VOL

MUTE

SMART

SOUND PICTURE

SETTING THE TV’S CLOCK

our television comes with an

Yonscreen clock. During normal

operation the clock appears on the

screen when the STATUS/EXIT but-

ton is pressed or when channel

changes occur.

BEGIN

Press the CLOCK button on

the remote to display the onscreen

CLOCK menu.

SET CLOCK

TIMER ACTIVE

CHANNEL

- - :- - AM

Press the CURSOR UP ▲ OR

CURSOR DOWN ▼ buttons until

the words SET CLOCK are high-

lighted.

SET CLOCK

TIMER ACTIVE

CHANNEL

10:00 AM

Enter the current time using

the NUMBERED buttons. If the

first number is a single digit first

enter a zero then the digit (i.e.,

press “0”, then press “8”).

POWER

CLOCK

SLEEP

Press the CURSOR RIGHT ᮣ

or CURSOR LEFT ᮤ buttons to

set either AM or PM time.

Note: The CLOCK onscreen menu

can also be accessed through the

main menu by pressing the MENU

button; then scrolling up/down

with the CURSOR UP ▲ or

CURSOR DOWN ▼ buttons until

the word CLOCK is highlighted.

Press the CURSOR RIGHT ᮣ

button to activate the CLOCK

menu and follow the steps above to

set the time.

A/CH

SURF

Note: If a power failure occurs, the

TV's CLOCK will have to be reset.

STATUS

EXIT

If no time is set, the time will not

appear onscreen.

VOL

MUTE

SMART

SOUND PICTURE

SMART HELP

Remember: Be sure to

press “0” first and then the

hour number for single digit

entries.

To clear the onscreen menu press

the STATUS/EXIT button or wait a

few seconds after you have fin-

ished your adjustment and the

menu will automatically disappear

from the screen.

ACTIVATING THE TV’S ON TIMER CONTROL

ust like an alarm clock you can

Jset the TV to turn itself on at the

BEGIN

same time everyday.

Press the CLOCK button to

display the Clock onscreen menu.

Press the CURSOR UP ▲ or

CURSOR DOWN ▼ button until

the words TIMER ACTIVE are

highlighted.

SET CLOCK

TIMER ACTIVE

CHANNEL

10:00 AM

OFF

Press the CURSOR RIGHT

ᮣ or CURSOR LEFT ᮤ button

to select ON (if activating) or OFF

(if deactivating) the Timer control.

SET CLOCK

TIMER ACTIVE

CHANNEL

10:00 AM

START TIME

- - : - - AM

START TIME

- - : - - AM

POWER

SLEEP

CLOCK

SMART HELP

Remember: Be sure to set

the clock to the current time,

then set the time you want the tele-

vision to turn on using the START

TIME control as described on page

21.

A/CH

SURF

STATUS

EXIT

The onscreen menu will time out

and disappear from the screen

when you finish, or you can press

the STATUS/EXIT button to clear

the menu from the screen.

VOL

MUTE

SMART

SOUND PICTURE

ACTIVATING THE START UP CHANNEL

sed along with the Clock fea-

Utures, you can select a specific

channel that the television will tune

to when the Timer Active control is

turned ON.

BEGIN

Press the CLOCK button to

display the Clock onscreen menu.

Press the CURSOR UP ▲ or

CURSOR DOWN ▼ button until

the word CHANNEL is highlighted.

SET CLOCK

TIMER ACTIVE

CHANNEL

10:00 AM

START TIME

- - : - - AM

Press the number buttons to

enter the start up channel you

would like the television to start on.

POWER

SLEEP

CLOCK

SMART HELP

Remember: Be sure to set

the Timer Active control to

ON.

A/CH

SURF

STATUS

The onscreen menu will time out

and disappear from the screen when

you finish, or you can press the

STATUS/EXIT button to clear the

menu from the screen.

EXIT

VOL

MUTE

SMART

SOUND PICTURE

SETTING THE TV’S START UP TIME

sed along with the Clock fea-

Uture, you can select a specific

time the television will turn on

when the Timer Active control is

turned ON.

BEGIN

Press the CLOCK button to

display the Clock onscreen menu.

TIMER ACTIVE

CHANNEL

Press the CURSOR UP ▲ or

CURSOR DOWN ▼ button until

the words START TIME are high-

lighted.

TIMER ACTIVE

CHANNEL

START TIME

- - : - - AM

START TIME

08:30 AM

Enter the time to turn on the

TV using the NUMBERED but-

tons. If the first number is a single

digit first enter a zero then the digit

(i.e., press “0”, then press “8”).

POWER

CLOCK

SLEEP

Press the CURSOR RIGHT ᮣ

or CURSOR LEFT ᮤ buttons to

set either AM or PM time.

8:30

A/CH

SURF

STATUS

EXIT

SMART HELP

Remember: Be sure to set

the Timer Active to ON.

VOL

MUTE

The onscreen menu will time out

and disappear from the screen when

you finish, or you can press the

STATUS/EXIT button to clear the

menu from the screen.

SMART

CHANGING

SOUND PICTURE

TO CHANNEL 6

IN 30 SECONDS

If the TV is in use when the START TIME control is about

to be activated, the screen will display a warning stating it's

going to change channels in 30 seconds. It will appear like

the screen shown below and change to the selected start up

channel. Pressing any button on the remote within this

count down will cancel the change.

USING THE CLOSED CAPTION CONTROL

losed Captioning (CC) allows

Cyou to read the voice content of

television programs on the TV

screen. Designed to help the hear-

ing impaired, this feature uses

onscreen “text boxes” to show dia-

logue and conversations while the

TV program is in progress.

NOTE: Not all TV programs and product commercials are made for broadcast

with Closed Caption (CC) information included. Neither are all Closed Caption

modes (CC-1, or CC-2) necessarily being used by a broadcast station during the

transmission of a closed caption program. Refer to your area's TV program listings

for the stations and times of Closed Caption shows.

BEGIN

Press the MENU button on the

remote to display the onscreen

menu.

SmartLock

CLOCK

ᮣ

OFF

ᮣ

SmartLock

CLOCK

ᮣ

Press the CURSOR UP ▲ or

CURSOR DOWN ▼ button until

the word CC (Closed Caption) is

highlighted.

SETUP

SmartLock REVIEW

ᮣ

SETUP

ᮣ

SmartLock REVIEW

Press the CURSOR RIGHT

ᮣ button to select the CLOSED

CAPTION option you want (OFF, 1,

2, or MUTE). Dialogue (and

descriptions) for the action on the

captioned TV program will appear

onscreen.

POWER

CLOCK

ᮣ

CLOCK

SLEEP

SETUP

ᮣ

SmartLock REVIEW

CLOCK

ᮣ

MUTE

ᮣ

NOTE: You can also set the

Closed Caption by pressing the CC

button on the remote. When pressed

repeatedly the screen will display the

options: CC-OFF, CC-1, CC-2, or

CC-MUTE.

A/CH

SURF

SETUP

STATUS

SmartLock REVIEW

ᮣ

EXIT

CC-1

VOL

MUTE

SMART

SOUND PICTURE

SMART HELP

Remember: The onscreen

menu will time out and disap-

pear from the screen when you fin-

ish, or you can press the

STATUS/EXIT button to clear the

menu from the screen.

CAPTION mode

Example Display

NOTE: The CC-MUTE option

can be used to set the TV to

turn the Closed Caption mode

“ON” whenever the MUTE but-

ton on the remote is pressed.

This activates the CC-1 option.

MUTE will appear smaller in

the upper center of the screen.

JOHN: Why did they move the

meeting up to this week?

MARSHA: I don't know, but they

are pushing to close the deal.

USING THE SLEEP TIMER CONTROL

ave you ever fallen asleep in

Hfront of the TV only to have it

wake you up at two in the morning

with a test pattern screeching in

your ears? Well, your TV can save

you all that trouble by automatical-

ly turning itself off.

15 MIN

BEGIN

Press the SLEEP button on the

remote control and the SLEEP timer

onscreen display will appear in the

lower center of the display.

30 MIN

45 MIN

60 MIN

Press the SLEEP button

repeatedly to pick the amount of

time (in 15 minute increments up to

60 minutes; then 30 minute incre-

ments up to 120 minutes; then 60

minute increments up to 240 min-

utes) before the TV will turn itself

off.

POWER

CLOCK

SLEEP

90 MIN

120 MIN

180 MIN

An onscreen count down will appear

during the last minute before the TV

shuts itself off.

A/CH

SURF

STATUS

EXIT

240 MIN

VOL

SMART HELP

MUTE

SMART

Remember: The SLEEP-

TIMER control can also be set

within the TV’s main menu.

SOUND PICTURE

The onscreen menu will time out

and disappear from the screen when

you finish, or you can press the

STATUS/EXIT button to clear the

menu from the screen.

50 SEC

10 SEC

During the last minute of a SLEEP

timer setting, an onscreen count

down will be displayed. Pressing

any button during the last minute

will cancel the SLEEP timer.

During the last 10 seconds of a

SLEEP timer setting, an onscreen

display will read GOOD BYE.

GOODBYE

UNDERSTANDING THE SMARTLOCK™ CONTROL

he SmartLock feature is an inte-

Tgrated circuit that receives and

processes data sent by broadcast-

ers, or other program providers,

that contain program content advi-

sories. When programmed by the

viewer, a TV with SmartLock can

respond to the content advisories

and block program content that may

be found objectionable (such as

offensive language, violence, sexual

situations, etc.). This is a great fea-

ture to censor the type of viewing

children may watch.

OFF

TV-Y

OFF

ᮣ

TV-Y7

TV-G

PG-1 3

OFF

ᮣ

TV-PG

TV-1 4

TV-MA

NC-1 7

ᮣ

Over the next few pages you’ll

learn how to block channels and

certain rated programming. Below

is a brief explanation of some terms

and ratings you will find in the

SmartLock feature.

MOVIE RATINGS

TV PARENTAL GUIDELINES

(MOTION PICTURE ASSOCIATION OF AMERICA)

(TV BROADCASTERS)

G: General Audience - All ages admit-

ted. Most parents would find this pro-

gram suitable for all ages. This type of

programming contains little or no vio-

lence, no strong language, and little or no

sexual dialogue or situations.

TV-Y - (All children -- This program

is designed to be appropriate for all

Y _{children.) Designed for a very young}

audience, including children ages 2-6. This

type of programming is not expected to

frighten younger children.

SmartLock offers various

BLOCKING OPTION controls

from which to choose:

PG: Parental Guidance Suggested - This

programming contains material that parents

may find unsuitable for younger children.)

It may contain one or more of the follow-

ing: Moderate violence, some sexual situa-

tions, infrequent coarse language, or some

suggestive dialogue.

TV-Y7 - (Directed to Older

Children -- This program is designed

_{for children age 7 and above.) It may}

MASTER DISABLE: This is what

might be called the "master switch"

for SmartLock. When in the ON

position, ALL blocking/censoring is

turned off (or disabled). When in the

OFF position, ALL blocking based

on specifically blocked settings will

take place.

be more appropriate for children who have

acquired the development skills needed to

distinguish between make-believe and reali-

ty. This programming may include mild fan-

tasy and comic violence (FV).

PG-13: Parents Strongly Cautioned - This

programming contains material that parents

may find unsuitable for children under the

age of 13. It contains one or more of the

following: violence, sexual situations,

coarse language, or suggestive dialogue.

TV-G - (General Audience -- Most

parents would find this program suit-

G_{able for all ages.) This type of pro-}

BLOCK UNRATED: ALL unrated

programs based on the Movie

Ratings or Parental (TV) Guidelines

can be blocked if this feature is set

to ON and the MASTER DISABLE

feature is set to OFF.

gramming contains little or no violence, no

strong language, and little or no sexual dia-

logue or situations.

R: Restricted -This is programming is

specifically designed for adults. Anyone

under the age of 17 should only view this

programming with an accompanying parent

or adult guardian. It contains one or more

of the following: intense violence, intense

sexual situations, strong coarse language,

or intensely suggestive dialogue.

TV-PG - (Parental Guidance

Suggested -- This program contains

material that parents may find unsuit-

BLOCK NO RATINGS: ALL pro-

gramming with NO content advisory

data can be blocked if this feature is

set to ON and the MASTER DIS-

ABLE feature is set to OFF.

able for younger children.) This type of pro-

gramming contains one or more of the fol-

lowing: Moderate violence (V), some sexual

situations (S), infrequent coarse language

(L), or some suggestive dialogue (D).

NC-17: No one under the age of 17 will

be admitted. - This type of programming

should be viewed by adults only. It con-

tains graphic violence, explicit sex, or

crude indecent language.

After an access code has been pro-

grammed, you can block up to 5

individual channels. But more than

just blocking channels, certain

blocking options exist which will

block programming based on ratings

patterned by the Motion Pictures

Association of America and TV

broadcasters. (See description of rat-

ings on this page.)

TV-14 - (Parents Strongly

Cautioned -- This program contains

_{some material that many parents}

would find unsuitable for children under 14

years of age.) This type of programming

contains one or more of the following:

intense violence (V), intense sexual situa-

tions (S), strong coarse language (L), or

intensely suggestive dialogue (D).

X: Adults Only - This type of programming

contains one or more of the following: very

graphic violence, very graphic and explicit

or indecent sexual acts, very coarse and

intensely suggestive language.

TV-MA - (Mature Audience Only --

This program is specifically designed

to be viewed by adults and therefore

may be unsuitable for children under 17.)

This type of programming contains one or

more of the following: graphic violence (V),

explicit sexual situations (S), or crude inde-

cent language (L).

UNDERSTANDING THE SMARTLOCK™ CONTROL (ACCESS CODE)

ver the next few pages you’ll

Olearn how to block channels

and get a better understanding of

the rating terms for certain pro-

gramming.

INPUT

ᮣ

OFF

ᮣ

First, let’s start by learning how to

set a personal access code:

SLEEPTIMER

SmartLock

CLOCK

SmartLock

BEGIN

ᮣ

Press the MENU button on the

remote to display the onscreen

menu.

OFF

ACCESS CODE

_ _ _ _

Press the CURSOR UP ▲ or

CURSOR DOWN ▼ buttons until

the words SmartLock are highlight-

ed.

POWER

SLEEP

CLOCK

SmartLock

Press the CURSOR RIGHT

ᮣ button to display the

SmartLock Access Code screen.

ACCESS CODE

X X X X

Using the NUMBERED but-

tons, enter 0, 7, 1, 1. “XXXX”

appears on the Access Code screen

as you press the numbered buttons.

A/CH

SURF

STATUS

EXIT

“INCORRECT CODE” will

appear on the screen, and you will

need to enter 0, 7, 1, 1 again.

SmartLock

VOL

Press the CURSOR DOWN ▼

button until the words CHANGE

CODE are highlighted.

MUTE

SMART

ACCESS CODE

_ _ _ _

SOUND PICTURE

Press the CURSOR RIGHT ᮣ

button to change your personal

Access Code.

INCORRECT CODE

“Next enter a “new” 4 digit

code using the NUMBERED but-

tons. The screen will then ask you

to confirm the code you just

entered. Enter your new code

again. “XXXX” will appear when

you enter your new code.

BLOCK

CHANGE CODE

ᮣ

CHANGE CODE X X X X

Press the STATUS/EXIT but-

ton to save the new code in the

TV's memory.

NOTE: The 0,7,1,1 access code shown

on this page is the default code or a

way to reset the code when the current

access code is not known.

CONFIRM CODE X X X X

Parents - it isn’t possible for your child

to unblock a channel without knowing

your access code or changing it to a new

one. If your code changes, and you did-

n’t change it, then you know it’s been

altered by someone else and blocked

channels have been viewed.

UNDERSTANDING THE SMARTLOCK™ CONTROL (BLOCK CHANNEL)

fter your personal access code

Ahas been set (see previous

page), you are now ready to select

the channels you want to block out

or censor.

INPUT

ᮣ

OFF

ᮣ

BEGIN

SLEEPTIMER

SmartLock

CLOCK

SmartLock

Press the MENU button on the

remote to show the onscreen menu.

ᮣ

OFF

Press the CURSOR UP ▲ or

CURSOR DOWN ▼ button until

the words SmartLock are highlight-

ed.

ACCESS CODE

POWER

SLEEP

SmartLock

Press the CURSOR RIGHT

ᮣ button to display the

SmartLock Access screen.

CLOCK

ACCESS CODE

X X X X

Enter the correct access code

number. “XXXX” shows on the

Access Code display as you press

the NUMBERED buttons.

A/CH

SURF

STATUS

EXIT

Press the CURSOR UP ▲ or

DOWN ▼ buttons until the word

BLOCK is highlighted. Press the

CURSOR RIGHT ᮣ button then

highlight CHANNELS

BLOCK

ᮣ

CHANGE CODE

VOL

MUTE

SMART

BLOCKED.

BLOCKING OPTIONS

ᮣ

SOUND PICTURE

Press the CURSOR RIGHT ᮣ

button. Three options will be dis-

played; CHANNEL, LOCK or

CLEAR ALL.

CHANNELS BLOCKED ᮣ

MOVIE RATINGS

PARENTAL GUIDELINE ᮣ

ᮣ

With CHANNEL highlighted,

use the NUMBERED buttons to

enter the channel number you wish

to block.

CHANNEL 5 BLOCKED

BY CHANNEL BLOCKING

ENTER CODE TO VIEW

CHANNEL

LOCK

YES

ᮣ

Use the CURSOR DOWN ▼

button to highlight the word

LOCK, then press the CURSOR

RIGHT ᮣ button to select YES

(block) or NO (do not block). The

channel chosen is now blocked from

viewing.

CHANNEL

LOCK

CLEAR ALL

ᮣ

When a blocked channel is viewed, this is what the screen will display. To view the blocked channel, sim-

ply enter the current access code. Note: Once the access code is entered ALL blocked channels will be

viewable until the TV is powered off. Once the set is turned off and then back on the previously blocked

channels will again be blocked.

Repeat steps 7 and 8 for any other

channels you wish to block from

viewing.

To clear blocked channels

follow the steps below:

Press the CURSOR DOWN ▼

button until the words CLEAR

ALL are highlighted, then press the

CURSOR RIGHT ᮣ button.

Note: When the CLEAR

ALL option is selected, the

CHANNEL option will dis-

play ALL.

If at this point if you change

the LOCK option to YES,

ALL channels will be blocked

from viewing.

CHANNEL

LOCK

ALL

CHANNEL

LOCK

YES

ᮣ

The screen will read “ALL

ALL UNLOCKED

CLEAR ALL

UNBLOCKED” for a moment. At

this point ALL the previously

blocked channels will be unblocked.

UNDERSTANDING THE SMARTLOCK™ CONTROL (BLOCKING OPTIONS)

martLock offers the viewer other

Sblocking features as well. With

these Blocking Option features, the

censoring can be turned ON or

OFF.

INPUT

ᮣ

OFF

ᮣ

SLEEPTIMER

SmartLock

CLOCK

BEGIN

SmartLock

Press the MENU button on the

remote to display the onscreen

menu.

ᮣ

OFF

ACCESS CODE

Press the CURSOR UP ▲ or

CURSOR DOWN ▼ buttons until

the words SMART LOCK are

highlighted.

POWER

SLEEP

CLOCK

SmartLock

Press the CURSOR RIGHT

ᮣ button to display the SmartLock

Access Code screen.

ACCESS CODE

X X X X

A/CH

SURF

STATUS

EXIT

Using the NUMBERED but-

tons on the remote, enter your per-

sonal Access Code.

VOL

With the word BLOCK high-

lighted, Press the CURSOR

RIGHT ᮣ button.

MUTE

SMART

BLOCK

CHANGE CODE

ᮣ

SOUND PICTURE

Scroll the menu using the

CURSOR UP ▲ or CURSOR

DOWN ▼ buttons until the words

BLOCKING OPTIONS are high-

lighted.

MASTER DISABLE

BLOCK UNRATED

MASTER DISABLE OFF

BLOCKING OPTIONS

ᮣ

BLOCK UNRATED

OFF

Press the CURSOR RIGHT ᮣ

button to display the Blocking

Options (MASTER DISABLE,

BLOCK UNRATED, or BLOCK

NO RATING). When highlighted,

each feature can be turned ON or

OFF using the CURSOR RIGHT

ᮣ or CURSOR LEFT ᮤ buttons

on the remote.

CHANNELS BLOCKED ᮣ

MOVIE RATINGS

BLOCK NO RATING ON

BLOCK NO RATING OFF

ᮣ

CHANNEL 2 0 BLOCKED

BY CONTENT ADVISORY

CANNOT DECODE RATING

ENTER CODE TO VIEW

If the BLOCK UNRATED or BLOCK NO RATINGS

controls are turned ON, all unrated programs and pro-

grams containing NO content advisory data will display

the screen shown to the left. To watch the channel enter

your access code, or change the BLOCK UNRATED

and BLOCK NO RATINGS back to off.

–

BLOCKING OPTIONS:

MASTER DISABLE: This is what might be called the “master switch” for SmartLock. When in the ON position, ALL block-

ing/censoring is turned off (or disabled). When in the OFF position, ALL blocking based on specifically blocked settings will

take place.

BLOCK UNRATED: ALL unrated programs based on the Movie Ratings or Parental (TV) Guidelines can be blocked if this

feature is set to ON and the MASTER DISABLE feature is set to OFF.

BLOCK NO RATINGS: ALL programming with NO content advisory data can be blocked if this feature is set to ON and the

MASTER DISABLE feature is set to OFF.

UNDERSTANDING THE SMARTLOCK™ CONTROL (MOVIE RATINGS)

SMART

HELP

here are two types of program

Tratings within the SmartLock

feature. One is based on the Movie

Industry ratings while the other is

based on the TV Industry ratings.

Both can be used to block or censor

programming that has been rated in

either manner.

Remember:

Selecting to

block any rating

will cause all the

higher ratings to

also be blocked

automatically.

ᮣ

INPUT

SLEEPTIMER

SmartLock

CLOCK

OFF

ᮣ

SmartLock

Let’s first look at the Movie Rating

options of SmartLock:

ᮣ

OFF

ACCESS CODE

_ _ _ _

BEGIN

Press the MENU button on the

remote to display the onscreen

menu.

POWER

SLEEP

SmartLock

CLOCK

Press the CURSOR UP ▲ or

CURSOR DOWN ▼ buttons until

the words SmartLock are highlight-

ed.

ACCESS CODE

X X X X

Press the CURSOR RIGHT

ᮣ button to display the SmartLock

Access Code screen.

A/CH

SURF

STATUS

EXIT

BLOCK

ᮣ

CHANGE CODE

Using the NUMBERED but-

tons on the remote, enter your

Personal Access Code.

VOL

MUTE

SMART

With the word BLOCK high-

lighted, Press the CURSOR

RIGHT ᮣ button.

SOUND PICTURE

ᮣ

BLOCKING OPTIONS

CHANNELS BLOCKED

MOVIE RATINGS

Scroll the menu using the

CURSOR UP ▲ or CURSOR

DOWN ▼ buttons until the words

MOVIE RATINGS are highlight-

ed.

PARENTAL GUIDELINE

CHANNEL 5 BLOCKED

BY CONTENT ADVISORY

OFF

Press the CURSOR RIGHT ᮣ

button to display the MOVIE

RATINGS (G, PG, PG-13, R,

NC17, or X).

PG-1 3

OFF

MOVIE RATING

ENTER CODE TO VIEW

_ _ _ _

NC-1 7

When highlighted, all these options

can be turned ON (which will allow

blocking) or OFF (which will allow

viewing).

NOTE: When a rating is turned ON, all

higher ratings will automatically be turned

ON. To turn them OFF, you will have to set

each rating individually. (i.e., R blocked

manually, NC-17 and X will be blocked

automatically.)

Screen will display a message when programming is

blocked by the Movie Rating feature. To unblock, turn

the Movie Rating OFF, or enter your personal access

code. Entering the code will unblock ALL blocked

Movie Ratings until the TV is turn off. Then the

blocked ratings will be reset to ON.

Use the CURSOR RIGHT ᮣ or

CURSOR LEFT ᮤ buttons on the

remote to turn the rating option ON

or OFF.

UNDERSTANDING THE SMARTLOCK CONTROL (PARENTAL GUIDELINE)

SMART

HELP

his portion of the SmartLock

Tfeatures cover program ratings

based on the TV Industry rating

system. This is known as Parental

Guideline within SmartLock.

Remember:

Selecting to

block any rating

will cause all the

higher ratings to

also be blocked

automatically.

After selecting the SmartLock fea-

ture and entering your personal

access code, the BLOCK/CHANGE

CODE screen appears;

BLOCK

ᮣ

CHANNELS BLOCKED

MOVIE RATINGS

CHANGE CODE

PARENTAL GUIDELINE

BEGIN

With the word BLOCK high-

lighted, Press the CURSOR

RIGHT ᮣ button.

POWER

SLEEP

CLOCK

ᮣ

TV-Y7

TV-G

Scroll the menu using the

CURSOR UP ▲ or CURSOR

DOWN ▼ buttons until the words

PARENTAL GUIDELINES are

highlighted.

OFF

ᮣ

TV-PG

TV-1 4

TV-MA

ᮣ

A/CH

SURF

Press the CURSOR RIGHT ᮣ

button to display the Parental

(TV) Guidelines (TV-Y, TV-Y7,

TV-G, TV-PG, TV-14, or TV-MA).

STATUS

EXIT

TV RATING SUB MENUS:

When highlighted, the TV-Y and

TV-G can be turned ON (which will

allow blocking), or OFF (which

will allow viewing) of these rated

programs.

VOL

MUTE

SMART

TV-Y

OFF

ᮣ

TV-Y7

TV-G

SOUND PICTURE

OFF

The ratings of TV-Y7, TV-PG,

TV-14, TV-MA can be cus-

ᮣ

TV-PG

tomized to block V (violence), FV

(fantasy violence), S (sexual situa-

tions), L (coarse language), or D

(suggestive dialogue).

ᮣ

TV-Y7

TV-G

Use the CURSOR RIGHT ᮣ or

CURSOR LEFT ᮤ buttons on the

remote to turn the rating option ON

or OFF.

OFF

ᮣ

TV-PG

TV-1 4

TV-MA

ᮣ

TV-Y - (All children -- This program is designed to be appropriate for all children.)

Designed for a very young audience, including children ages 2-6. This type of pro-

gramming is not expected to frighten younger children.

1 4

TV-G

OFF

ᮣ

TV-PG

TV-1 4

TV-MA

TV-Y7 - (Directed to Older Children -- This program is designed for children age 7

and above.) It may be more appropriate for children who have acquired the develop-

ment skills needed to distinguish between make-believe and reality. This program-

ming may include mild fantasy and comic violence (FV).

ᮣ

TV-G - (General Audience -- Most parents would find this program suitable for all

ages.) This type of programming contains little or no violence, no strong language,

and little or no sexual dialogue or situations.

TV-PG - (Parental Guidance Suggested -- This program contains material that par-

ents may find unsuitable for younger children.) This type of programming contains

one or more of the following: some suggestive dialogue (D), infrequent coarse lan-

guage (L), some sexual situations (S), or moderate violence (V).

ᮣ

TV-PG

TV-1 4

TV-MA

TV-14 - (Parents Strongly Cautioned -- This program contains some material that

many parents would find unsuitable for children under 14 years of age.) This type of

programming contains one or more of the following: intensely suggestive dialogue

(D), strong coarse language (L), intense sexual situations (S), or intense violence (V).

TV-MA - (Mature Audience Only -- This program is specifically designed to be

viewed by adults and therefore may be unsuitable for children under 17.) This type of

programming contains one or more of the following: crude indecent language (L),

explicit sexual situations (S), or graphic violence (V).

UNDERSTANDING THE SMARTLOCK™ CONTROL (REVIEW SCREEN)

ow that you’ve learned how to

Nblock channels or censor your

viewing, using the Movie Ratings

or Parental (TV) Guidelines, let’s

review what you’ve done. The

SmartLock Review feature allows

you to see what has been blocked.

Whenever the Menu button is

pressed the onscreen menu will be

displayed with the SmartLock

Review highlighted.

OFF

ᮣ

CHANNELS BLOCKED

-- -- -- -- --

SETUP

ᮣ

SmartLock REVIEW

BRIGHTNESS

COLOR

MOVIE RATINGS

-- -- -- -- --

PARENTAL GUIDELINE

-- -- -- -- --

BEGIN

BLOCK UNRATED

OFF

Press the MENU button on the

remote to show the onscreen menu.

SmartLock REVIEW will be high-

lighted.

BLOCK NO RATING OFF

POWER

CLOCK

SLEEP

Press the CURSOR RIGHT

ᮣ button and the SmartLock

Review Menu will appear.

SmartLock DISABLED

This menu will display what chan-

nels have been blocked; what

A/CH

SURF

STATUS

Movie Ratings have been blocked;

what Parental (TV Ratings)

EXIT

Guideline have been blocked. This

review screen will also display the

status of Unrated and No Rating

settings. If the Master Disable fea-

ture has been turned ON, the

SmartLock DISABLED will appear in the

SmartLock Review screen if the SmartLock

Disable feature is set to ON.

VOL

MUTE

SMART

SmartLock Review screen will dis-

play “SmartLock DISABLED”.

SOUND PICTURE

CHANNELS BLOCKED - Shows all blocked channels that where set with-

in the CHANNELS BLOCKED feature. Up to 5 channels may be blocked at

one time.

MOVIE RATINGS - Shows all blocked Movie Ratings that were set within

the MOVIE RATINGS feature. All or some may be blocked at one time.

Note: If a lower rating is blocked, this will automatically cause the higher

ratings to be blocked also. (i.e., if R is set to be blocked, X will automatical-

ly be blocked also.)

CHANNELS BLOCKED

5 1 0 1 2 3 2 4 5

MOVIE RATINGS

PARENTAL GUIDELINE - Shows all blocked TV Ratings that were set

within the PARENTAL GUIDELINES feature. All or some may be blocked

at one time. Note: If a lower rating is blocked; this will automatically cause

the higher ratings to be blocked also. (i.e., if TV-14 is set to be blocked, TV-

MA will automatically be blocked.) Parental Guidelines also have sub ratings

for Violence (V), Fantasy Violence (FV), Sexual Situations (S), Coarse

Language (L), and Suggestive Language (D). If the main rating is turned off

but the sub rating is turned ON, the program will be blocked but the rating

will not appear within the SmartLock Review menu.

-- -- -- R X

PARENTAL GUIDELINE

-- -- -- 1 4 MA

BLOCK UNRATED - Shows ON or OFF depending on the status of the

BLOCK UNRATED feature. Based on the Movie Ratings or Parental (TV)

Guidelines.

BLOCK UNRATED

BLOCK NO RATING - Shows ON or OFF depending on the status of the

BLOCK NO RATING feature. Based on programming with NO content

advisory data.

BLOCK NO RATING ON

SETTING THE BASS AND TREBLE BOOST CONTROLS

esides the normal volume level

Bcontrol, your TV also has Bass

and Treble Boost sound adjustment

controls. The TREBLE Boost effects

only the high frequency sound com-

ing from the TV enhancing the

highs; while the BASS Boost effects

only the low frequency sound com-

ing from the TV enhancing the lows.

NOISE REDUCTION

VOLUME

1 5

NOISE REDUCTION

VOLUME

1 5

TREBLE BOOST

BASS BOOST

OFF

TREBLE BOOST

BASS BOOST

SOUND

STEREO

SOUND

STEREO

BEGIN

Press the MENU button on the

remote to show the onscreen

menu.

POWER

CLOCK

SLEEP

Press the CURSOR UP ▲ or

CURSOR DOWN ▼ buttons to

select and highlight the name of the

control you wish to change (TRE-

BLE BOOST, or BASS BOOST).

VOLUME

1 5

TREBLE BOOST

BASS BOOST

SOUND

OFF

A/CH

SURF

STEREO

STATUS

EXIT

SAP

Use the CURSOR LEFT ᮤ or

RIGHT ᮣ buttons to turn the

selected control ON or OFF.

VOL

MUTE

VOLUME

1 5

SMART

TREBLE BOOST

BASS BOOST

SOUND

SOUND PICTURE

STEREO

SAP

USING THE TV VOLUME BAR CONTROL

se the Volume Bar control to see

Uthe TV’s volume level settings

on the TV screen. The Volume Bar

will be seen each time the VOLUME

buttons (on the TV or remote) are

pressed.

CONTRAST PLUS

NOISE REDUCTION

VOLUME

1 5

TREBLE BOOST

BASS BOOST

VOLUME

1 5

BEGIN

Press the MENU button to dis-

play the onscreen menu.

POWER

SLEEP

Press the CURSOR UP ▲ or

CURSOR DOWN ▼ buttons until

the word VOLUME is highlighted.

CLOCK

SLEEP

CLOCK

Note: Pressing the VOL

Press the CURSOR RIGHT ᮣ

button to increase the TV’s volume

or the CURSOR LEFT ᮤ button to

decrease the sound.

(+) or (–) buttons will

also allow you to adjust

the sound level of the

TV. A Volume Bar

A/CH

SURF

A/CH

SURF

STATUS

EXIT

adjustment will appear

onscreen. Press the (+)

to increase the volume

and the (–) button to

decrease the volume.

VOL

MUTE

SMART

HOW TO USE THE INPUT CONTROL (A/V INPUTS)

AUDIO/VIDEO INPUTS

The TV’s Audio/Video Input jacks

are for direct picture and sound

connections between the TV and

a VCR (or similar device) that

has Audio/Video Output jacks.

BEGIN

⍀

VIDEO

AUDIO

Connect the VIDEO (yellow)

CABLE to the VIDEO IN jack

on the back of the TV. Then con-

nect the AUDIO (red and white)

CABLES to the AUDIO (left and

right) IN jacks on the rear of the

TV.

75 ⍀

VIDEO IN

(YELLOW)

BACK OF TV

AUDIO IN

(RED or WHITE)

Connect the VIDEO (yellow)

CABLE to the VIDEO OUT jack

on the back of the VCR. Then

connect the AUDIO (red and

white) CABLES to the AUDIO

(left and right) OUT jacks on the

rear of the VCR.

ANTENNA

OUT

AUDIO

OUT

VIDEO

VCR

(EQUIPPED WITH

VIDEO AND AUDIO

OUTPUT JACKS)

ANTENNA

OUT

BACK OF VCR

Turn the VCR and the TV

ON.

TREBLE BOOST

BASS BOOST

INPUT

Press the MENU button on

the remote to display the

onscreen menu.

ᮣ

SLEEPTIMER

SmartLock

OFF

ᮣ

Press the CURSOR UP ▲ or

CURSOR DOWN ▼ buttons

until the word INPUT is high-

lighted.

ANTENNA

EXT 1

POWER

SLEEP

Press the CURSOR RIGHT

ᮣ or CURSOR LEFT ᮤ button

to display the picture/sound menu

(ANTENNA, EXT 1). Use the

CURSOR UP ▲ or DOWN ▼

buttons to select.

CLOCK

A/CH

SURF

STATUS

EXIT

Now your ready to place a prere-

corded video tape in the VCR and

press the PLAY ᮣ button.

VOL

MUTE

SMART

SOUND PICTURE

USING THE SMARTPICTURE™ CONTROL

hether you’re watching a

Wmovie or a video game, your

TV has automatic video control set-

tings matched for your current pro-

gram source or content. The

SmartPicture feature quickly resets

your TV’s video controls for a num-

ber of different types of programs

and viewing conditions you may

have in your home. Each

SmartPicture setting is preset at the

factory to automatically adjust the

TV’s Brightness, Color, Picture,

Sharpness, Tint, and Color

PERSONAL

Temperature levels.

MOVIES

BEGIN

Press the SMART PICTURE

button on the remote control. The

current SmartPicture setting will

appear in the middle of the screen.

POWER

SPORTS

Press the SmartPicture button

repeatedly to select either PER-

SONAL, MOVIES, SPORTS, or

WEAK SIGNAL picture settings.

CLOCK

SLEEP

Note: The PERSONAL control is

set using the PICTURE options

within the onscreen menu. This is

the only SmartPicture control set-

ting that can be changed. All other

settings are setup at the factory dur-

ing the time of production.

A/CH

SURF

STATUS

WEAK SIGNAL

EXIT

VOL

MUTE

SMART

SOUND PICTURE

USING THE SMARTSOUND™ CONTROL

he SmartSound feature allows

Tthe listener to select between

four different factory set sound

options. Personal (which can be set

by the user), Theater (for movie

viewing), Music (for musical type

programming) and Voice (when the

program is mainly dialogue). To

select any of the options follow the

directions below.

BEGIN

PERSONAL

Press the SMART SOUND but-

ton on the remote control. The cur-

rent SmartSound setting will appear

in the middle of the screen.

THEATER

Press the SMART SOUND

button repeatedly to toggle

between the four settings.

POWER

MUSIC

Remember, only the PERSONAL

control can be changed by the view-

er. This changes the settings in the

main onscreen menu's sound con-

trols.

CLOCK

SLEEP

A/CH

SURF

STATUS

VOICE

EXIT

SMART HELP

Remember, SmartSound

works only with the pro-

VOL

grams coming through the 75Ω

input on the rear of the TV (RF

audio). It will not control the

sound levels for the External con-

nections.

NOTE: When the VOICE mode of

SmartSound is selected the AVL fea-

ture will be automatically turned ON.

MUTE

SMART

SOUND PICTURE

AVL CONTROL

In most cases the volume levels com-

ing from broadcast programming or

commercials are never the same.

With the AVL control turned ON,

you can have the TV level out the

sound being heard. This makes for a

more consistent sound by reducing

the peaks and valleys that occur dur-

ing program changes or commercial

breaks.

TREBLE BOOST

BASS BOOST

AVL

OFF

ᮣ

TREBLE BOOST

BASS BOOST

AVL

ᮣ

INPUT

SLEEPTIMER

OFF

INPUT

SLEEPTIMER

OFF

USING THE TV’S SMARTSURF™ CONTROL

“list” or series of previously

Aviewed channels can be select-

ed with the SURF button on your

remote control. With this feature

you can easily switch between dif-

ferent TV programs that currently

interest you. The SmartSurf control

allows you set up to eight channels

in its quick viewing “list”.

ADDED

BEGIN

Press the CHANNEL (+) or (–)

buttons (or the NUMBER buttons)

to select a channel to add to the

SURF list.

Press the SURF button on the

remote while the channel number is

still displayed to ADD the channel to

the SURF list.

POWER

ADDED

CLOCK

SLEEP

Repeat steps 1 through 2 to add

additional channels (up to 8) to the

SURF list.

A/CH

SURF

STATUS

EXIT

To remove a channel for the SURF

list, simply choose the channel with

the numbered buttons and press the

SURF button while the channel

number is still displayed and the

screen will read DELETED.

ADDED

VOL

MUTE

SMART

SOUND PICTURE

A/CH BUTTON

Your remote also has an A/CH

(Alternate Channel) button.

Pressing this button will toggle

between the Current and one previ-

ously selected channel.

SURF

Press the SURF button repeatedly to cycle or "loop"

through the channels saved in the SURF channel list.

A/CH

SURF

STATUS

EXIT

TIPS IF SOMETHING ISN'T WORKING

lease make these simple

Pchecks before calling for ser-

vice. These tips can save you time

and money since charges for TV

installation and adjustment of

customer controls are not cov-

ered under your warranty.

CAUTION: A video source (such as a video game, Compact Disc Interactive - CDI, or

TV information channel) which shows a constant non-moving pattern on the TV screen,

can cause picture tube damage. When your TV is continuously used with such a source

the pattern of the non-moving portion of the game (CDI, etc.) could leave an image

permanently on the picture tube. When not in use, turn the video source OFF.

Regularly alternate the use of such video sources with normal TV viewing.

• Check the TV power cord. Unplug the TV, wait 10 seconds, then reinsert plug into

outlet and push POWER button again.

• Check that outlet is not on a wall switch. Be sure fuse is not blown on AC Power strip.

No Power

No Picture

• Check antenna connections. Are they properly secured to the TV's ANT/CABLE plug?

• Check the TUNER control for CABLE or ANTENNA setting.

• Check the VOLUME buttons.

• Check the MUTE button on the remote control.

No Sound

• Check batteries. Replace with AA Heavy Duty (Zinc Chloride) or Alkaline batteries

if necessary.

• Clean the remote and the remote sensor window on the TV.

• Check the TV power cord. Unplug the TV, wait 10 seconds, then reinsert plug into

outlet and push POWER button again. Be sure fuse is not blown on AC Power strip.

• Check to be sure TV outlet is not on a wall switch.

Remote Does Not

Work

• Repeat channel selection.

• Add desired channel numbers (CHANNEL control) into TV memory.

• Check to be sure the TUNER control is set to the CABLE option.

TV Displays Wrong

Channel or No

Channels Above 13

Cleaning and Care

• To avoid possible shock hazard be sure the TV is unplugged from the electrical outlet before cleaning.

• When cleaning the TV screen take care not to scratch or damage the screen surface (avoid wearing jewelry or using

anything abrasive). Wipe the front screen with a clean cloth dampened with water. Use even, easy, vertical strokes when

cleaning.

• Gently wipe the cabinet surfaces with a clean cloth or sponge dampened in a solution of cool clear water. Use a clean

dry cloth to dry the wiped surfaces.

• Never use thinners, insecticide sprays, or other chemicals on or near the cabinet, as they might cause permanent marring

of the cabinet finish.

GLOSSARY TO TELEVISION TERMS

Coaxial Cable • A single solid antenna wire normally matched with a Programming • The procedure of adding or deleting channel numbers

metal plug (F-type) end connector that screws (or pushes) directly onto a into the Television’s memory circuits. In this way the Television

75 Ohm input found on the Television or VCR.

“remembers’’ only the locally available or desired channel numbers

and skips over any unwanted channel numbers.

Closed Caption • Broadcast standard which allows you to read the

voice content of television programs on the TV screen. Designed to help

Remote Sensor Window • A window or opening found on the

the hearing impaired this feature uses onscreen "text boxes" to show dia- Television control panel through which infrared remote control com-

logue and conversations while the TV program is in progress.

mand signals are received.

Direct Audio/Video Inputs • Located on the rear of the TV these con-

nectors (RCA phono type plug) are used for the input of audio and

video signals. Designed for use with VCRs (or other accessories) in

order to receive higher picture resolution and offer sound connection

options.

Setup Mode • Automatic feature control settings made by the TV.

Designed for first time setup and use. Settings for signal connections

(antenna or cable TV), plus channel program memory are held in the

TV's memory (even if the set is unplugged and moved to a new loca-

tion.)

Identify • Method by which a remote control searches and finds an

operating code for another product (such as a VCR or Cable Converter).

Once the code has been "identified" then the TV remote can operate and

send commands to the other product.

Second Audio Program (SAP) • Another or additional audio channel

provided for in the Multichannel Television Sound (MTS) broadcast

standard. The most frequently proposed use for SAP is the simultane-

ous bilingual broadcast of TV program material.

Onscreen Displays (OSD) • Refers to the wording or messages generat-

ed by the television (or VCR) to help the user with specific feature con-

trols (color adjustment, programming, etc.).

Status • Allows the user to quickly confirm what channel number is

currently being viewed. Status can also be used to clear the Television

of onscreen displays or information (rather than waiting for the dis-

plays to “time out” or automatically disappear from the screen).

Menu • An onscreen listing of feature controls shown on the Television

screen that are made available for user adjustments.

Twin Lead Wire • The more commonly used name for the two strand

300 Ohm antenna wire used with many indoor and outdoor antenna

systems. In many cases this type of antenna wire requires an additional

adapter (or balun) in order to connect to the 75 Ohm Input terminals

designed into the more recent Televisions and VCRs.

Multichannel Television Sound (MTS) • The broadcast standard that

allows for stereo sound to be transmitted with the TV picture.

INDEX

Accessories/Optional . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-7

Adapter Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7

Add/Delete Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Alternate Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Audio/Video Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Bass Boost Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Battery Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Cable TV Connections/Settings . . . . . . . . . . . . . . . . . . . . . . . . . .5, 11

Channel Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12, 13

Clock Set Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Closed Captioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Contrast Plus (Black Stretch) Control . . . . . . . . . . . . . . . . . . . . . . . .16

Controls/TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Controls/Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8, 9

External Control (Input Naming) . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Glossary TV Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Input Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Language Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Memory/Program Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12, 13

Menu Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Minus(-)/Plus (+) Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Picture Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Picture Noise Reduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Precautions/Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3, 36, 40

Programming Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-9

Requesting Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38-40

RF Coaxial Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-7

Safety/Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3, 36, 40

Sensor Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Set Up/First Time Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-13

Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

SmartLock - Understanding the SmartLock Control . . . . . . . . . . . . .24

SmartLock Access Code Feature . . . . . . . . . . . . . . . . . . . . . . . . . . .25

SmartLock Block Channel Feature . . . . . . . . . . . . . . . . . . . . . . . . . .26

SmartLock Blocking Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

SmartLock Blocking using the Movie/TV Ratings . . . . . . . . . . . .28-29

SmartLock Review . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

SmartPicture Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

SmartSound Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

SmartSurf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Start-up Channel Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Start-up Time Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Status Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Timer Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Tips for Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36, 38-40

Treble Boost Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

VCR/TV Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Volume Bar Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Philips Consumer Electronics Company

Factory Service Center Locations

Detroit/Toledo

•

Cleveland/

•

^{N Ohio}•

•

Chicago

★ Columbus

•

San Francisco/Metro Area

★ Los Angeles

Charlotte

★

•

★ Pittsburgh/WV Area

Knoxville/E Tennessee

•

Philadelphia/S New Jersey

Atlanta/N Georgia

• Dallas

★ Wash/Balt

★ Orlando

•

Houston/Galveston

Beaumont/Austin

San Antonio

Tampa/W Florida

★ Ft. Myers/SW Florida

•

★ Indicates In-Home Service Only

1-800-242-9225

★ Miami/SE Florida

• Indicates In-Home/Carry-In Service

NOTE: If you reside in one of our Philips Factory Service Branch areas (see directory on back), you can contact the nearest Service Branch to

obtain efficient and expedient repair for your product. If your product is In-Warranty, you should have proof-of-purchase to ensure No Charge

Service. For Out-of-Warranty service, call the location nearest you.

NOTA: Si vous résidez dans une des régions desservies par une succursale de service après vente du fabricant Philips (voir liste ci-dessous),

vous pourrez contacter la branche de service après vente la plus près de chez vous pour obtenir un service après vente rapide et efficace. Si le

produit est sous garantie, il suffira de présenter une preuve d`achat pour bénéficier d'un service sans frais. Pour les produits non couverts par la

garantie, contactez le centre le plus près de chez vous.

NOTA: Si Ud. reside en una de nuestras zonas para sucursales Philips de servicio al de fábrica (ver directorio más abajo), Ud. puede comunicarse

con la sucursal de servicio más cercana para obtener una reparación oportuna y eficaz de su producto. Si su producto está todavía bajo garan-

tía, Ud. debe presentar comprobante de compra para no ocasionar ningunos cargos por servicio. Para servicio después del vencimiento de la

garantía, llame al lugar más cercano de los abajo indicados.

In Canada

How you can obtain efficient and expedient carry-in, mail-in, or in-home service for your product

Please contact Philips at

1-800-661-6162 (French speaking)

1-800-363-7278 (English speaking)

Au Canada

Comment obtenir le service après-vente pour les produits apportés ou envoyés par la poste à notre centre de service ou le service à domicile

Veuillez contacter philips á:

1-800-661-6162 (Francophone)

1-800-363-7278

En el Canadá

Cómo recibir servicio efficiente para su producto, en persona, por correo o a domicillo

Favor de comunicarse con Philips al:

1-800-661-6162 (francófono)

1-800-363-7278 (anglófono)

EL4482-3 Rev. AA

3135 015 07541

MAC2929 1/99

QUALITY SERVICE IS AS CLOSE AS YOUR TELEPHONE! SIMPLY LOOK OVER THE LIST BELOW FOR THE NUMBER OF A FACTORY SERVICE CENTER

NEAR YOU. YOUR PRODUCT WILL RECEIVE EFFICIENT AND EXPEDIENT CARRY-IN, MAIL-IN, OR IN-HOME SERVICE, AND YOU WILL RECEIVE PEACE OF MIND,

KNOWING YOUR PRODUCT IS BEING GIVEN THE EXPERT ATTENTION OF PHILIPS’ FACTORY SERVICE. AND, IF THE PHONE NUMBER LISTED FOR YOUR AREA

IS LONG DISTANCE, CALL 1-800-242-9225 FOR FACTORY SERVICE.

COMMENT OBTENIR NOTRE SERVICE APRÈS VENTE RAPIDE ET EFFICACE SOIT PAR COURRIER, À DOMICILE, OU EN SE PRÉSENTANT À UN CENTRE DE SERVICE PHILIPS. PLUS DE 600 CENTRES

DE RÉCEPTION DE PRODUITS À RÉPARER À TRAVERS LE PAYS: CONTACTER LE CENTRE DE SERVICE AUX CONSOMMATEURS LE PLUS PROCHE POUR SAVOIR L’EMPLACEMENT DE CES DÉPÔTS

DANS UN RAYON DE 50 À 75 MILES (80 KM À 120 KM) DU CENTRE DE SERVICE LOCAL.

CÓMO OBTENER UN SERVICIO OPORTUNO Y EFICIENTE POR CORREO, EN CASA O EN PERSONA PARA SU PRODUCTO A TRAVÉS DE UN CENTRO PHILIPS DE SERVICIO. MAS DE 600 SITIOS POR

TODO EL PAIS PARA LA RECEPCION DE PRODUCTOS NECESITADOS DE REPARACIONES: COMUNICARSE CON EL CENTRO DE SERVICIO DE FABRICA MAS CERCANO PARA ESTOS LUGARES DENTRO

DE UN RADIO DE 80 A 120 KM (50 A 75 MILLAS) DEL CENTRO DE SERVICIO LOCAL.

GEORGIA

CENTRAL U.S.A.

ILLINOIS

Philips Factory Service of Georgia

200 N. Cobb Pkwy., Suite 120

Marietta, GA 30062

Philips Factory Service Central US

950 Keynote Circle

Brooklyn Heights, OH 44131

(216) 741-3334

Philips Factory Service of Illinois

1279 W. Hamilton Pkwy.

Itasca, IL 60143

(770) 795-0085

(630) 775-0990

FLORIDA

MICHIGAN

TENNESSEE

Philips Factory Service of Florida

1911 US Highway 301 North

Tampa, FL 33619

Philips Factory Service of Michigan

25173 Dequindre

Madison Heights, MI 48071

(248) 544-2110

Philips Factory Service of East Tennessee

6700 D Papermill Rd.

Knoxville, TN 37919

(813) 621-8181

(423) 584-6614

WESTERN U.S.A.

DALLAS AREA

MID-ATLANTIC

Philips Factory Service Western Region

681 East Brokaw Rd.

San Jose, CA 95112

Philips Factory Service of Dallas

415 N. Main Street, #107

Euless, TX 76040

Philips Factory Service Mid-Atlantic

352 Dunks Ferry Rd.

Bensalem, PA 19020

(215) 638-7500

(408) 436-8566

(713) 682-3990

TEXAS

Philips Factory Service of Texas

1110 N. Post Oak Rd., Suite 100

Houston, TX 77055

(713) 682-3990

MAC2929 1/99

LIMITED W ARRANTY

CO LO R TELEVISIO N

90 Days Free Labor

One Year Free Replacement of Parts (Two Years Free Replacement on Color Picture Tube)

This product must be carried in for repair.

W HO IS CO VERED?

MAKE SURE YO U KEEP...

You must have proof of purchase to receive warranty service. A sales

receipt or other document showing that you purchased the product is

considered proof of purchase.

Please keep your sales receipt or other document showing proof of

purchase. Attach it to this owner’s manual and keep both nearby.

Also keep the original box and packing material in case you need to

return your product.

W HAT IS CO VERED?

BEFO RE REQ UESTING SERVICE...

Please check your owner’s manual before requesting service.

Adjustments of the controls discussed there may save you a service

call.

Warranty coverage begins the day you buy your product. For 90 days

thereafter, all parts will be repaired or replaced free, and labor is free.

From 90 days to one year from the day of purchase, all parts will be

repaired or replaced free, but you pay for all labor charges. From one

to two years from the day of purchase, you pay for the replacement or

repair of all parts except the picture tube, and for all labor charges.

After two years from the day of purchase, you pay for the replacement

or repair of all parts, and for all labor charges.

TO GET W ARRANTY SERVICE IN U.S.A.,

PUERTO RICO O R U.S. VIRGIN ISLANDS...

Contact a Philips factory service center (see enclosed list) or autho-

rized service center to arrange repair.

All parts, including repaired and replaced parts, are covered only for

the original warranty period. When the warranty on the product

expires, the warranty on all replaced and repaired parts also expires.

(In U.S.A., Puerto Rico and U.S. Virgin Islands, all implied warranties,

including implied warranties of merchantability and fitness for a partic-

ular purpose, are limited in duration to the duration of this express

warranty. But, because some states do not allow limitations on how

long an implied warranty may last, this limitation may not apply to

you.)

W HAT IS EXCLUDED?

Your warranty does not cover:

•

labor charges for installation or setup of the product, adjustment of

customer controls on the product, and installation or repair of

antenna systems outside of the product.

TO GET W ARRANTY SERVICE IN CANADA...

Please contact Philips at:

•

product repair and/or part replacement because of misuse, acci-

dent, unauthorized repair or other cause not within the control of

Philips Consumer Electronics Company.

1-800-661-6162 (French Speaking)

1-800-363-7278 (English Speaking)

•

reception problems caused by signal conditions or cable or antenna

systems outside the unit.

a product that requires modification or adaptation to enable it to

operate in any country other than the country for which it was

designed, manufactured, approved and/or authorized, or repair of

products damaged by these modifications.

(In Canada, this warranty is given in lieu of all other warranties. No

other warranties are expressed or implied, including any implied war-

ranties of merchantability or fitness for a particular purpose. Philips is

not liable under any circumstances for any direct, indirect, special, inci-

dental or consequential damages, howsoever incurred, even if notified

of the possibility of such damages.)

•

incidental or consequential damages resulting from the product.

(Some states do not allow the exclusion of incidental or consequen-

tial damages, so the above exclusion may not apply to you. This

includes, but is not limited to, prerecorded material, whether copy-

righted or not copyrighted.)

REMEMBER...

• a product used for commercial or institutional purposes.

Please record the model and serial numbers found on the product

below. Also, please fill out and mail your warranty registration card

promptly. It will be easier for us to notify you if necessary.

W HERE IS SERVICE AVAILABLE?

Warranty service is available in all countries where the product is offi-

cially distributed by Philips Consumer Electronics Company. In coun-

tries where Philips Consumer Electronics Company does not distribute

the product, the local Philips service organization will attempt to pro-

vide service (although there may be a delay if the appropriate spare

parts and technical manual(s) are not readily available).

MODEL # ________________________________________________

SERIAL # ________________________________________________

This warranty gives you specific legal rights. You may have other rights which vary from state/province to state/province.

Philips Consum er Electronics Com pany, P.O . Box 2976, Longview, Texas 75606, (903) 242-4800

Printed in U.S.A.

IBM CFC2 User Manual
Intel Cpu Xeon CM8063501292204 User Manual
Jenn Air Convection Oven w30400 User Manual
JVC DIGIPURE HV L34PRO User Manual
LG Electronics LG Life Good Computer Monitor L204WTM User Manual
Miele KM5955 User Manual
Motorola D1110 User Manual
Panasonic WV CK2020A User Manual
Philips 14PT2682 User Manual
Philips 107E63 User Manual