Panasonic Computer Hardware AW HHD870N User Manual

Operating Instructions  
SDI Card  
Model No.  
AW-HHD870N  
Before operating this product, please read the instructions carefully and save this manual for future use.  
VQTB0353  
D
F0109S0  
For CANADA  
This Class A digital apparatus complies with Canadian  
ICES-003.  
Cet appareil numérique de la class A est conforme à  
la norme NMB-003 du Canada.  
FCC Note:  
This equipment has been tested and found to comply  
with the limits for a class A digital device, pursuant to  
Part 15 of the FCC Rules. These limits are designed  
to provide reasonable protection against harmful  
interference when the equipment is operated in a  
commercial environment. This equipment generates,  
uses, and can radiate radio frequency energy, and if  
not installed and used in accordance with the  
instruction manual, may cause harmful interference  
to radio communications. Operation of this equipment  
in a residential area is likely to cause harmful  
interference in which case the user will be required to  
correct the interference at his own expense.  
Warning:  
To assure continued FCC emission limit compliance,  
the user must use only shielded interface cables when  
connecting to external units. Also, any unauthorized  
changes or modifications to this equipment could void  
the user’s authority to operate it.  
indicates safety information.  
- 3 -  
IMPORTANT SAFETY INSTRUCTIONS  
Read these operating instructions carefully before using the unit. Follow the safety instructions on the unit and the  
applicable safety instructions listed below. Keep these operating instructions handy for future reference.  
1) Read these instructions.  
ꢀ) Keep these instructions.  
3) Heed all warnings.  
10) Protect the power cord form being walked on or  
pinched particularly at plugs, convenience  
receptacles, and the point where they exit from  
the apparatus.  
11) Only use attachments/accessories specified by  
the manufacturer.  
ꢁ) Follow all instructions.  
5) Do not use this apparatus near water.  
6) Clean only with dry cloth.  
1ꢀ) Use only with the cart, stand, tripod,  
bracket, or table specified by the  
manufacturer, or sold with the  
apparatus. When a cart is used, use  
7) Do not block any ventilation openings. Install in  
accordance with the manufacturer’s instructions.  
caution  
when  
moving  
the  
8) Do not install near any heat sources such  
as radiators, heat registers, stoves, or other  
apparatus (including amplifiers) that produce heat.  
cart/apparatus combination to avoid  
injury from tip-over.  
13) Unplug this apparatus during lightning storms or  
when unused for long periods of time.  
9) Do not defeat the safety purpose of the polarized  
or grounding-type plug. A polarized plug has two  
blades with one wider than the other. A grounding-  
type plug has two blades and a third grounding  
prong. The wide blade or the third prong are  
provided for your safety. If the provided plug does  
not fit into your outlet, consult an electrician for  
replacement of the obsolete outlet.  
1ꢁ) Refer all servicing to qualified service personnel.  
Servicing is required when the apparatus has  
been damaged in any way, such as power-supply  
cord or plug is damaged, liquid has been spilled or  
objects have fallen into the apparatus, the  
apparatus has been exposed to rain or moisture,  
does not operate normally, or has been dropped.  
indicates safety information.  
- ꢁ -  
Contents  
Preface ............................................................................... 5  
Standard accessories ......................................................... 5  
Warning/caution for safety .................................................. 6  
Precautions ......................................................................... 7  
Major operating controls and their functions ....................... 8  
Mounting ............................................................................. 9  
Connection ....................................................................... 11  
Appearance ...................................................................... 1ꢀ  
Specifications ................................................................... 13  
Preface  
This product is an option card which can be installed in  
Zoom focus control of lenses equipped with a remote  
control function possible from a AW-CBꢁ00 (or similar)  
remote operation panel.  
the option slot of the AW-HE870 HD convertible camera.  
It is made for HD-SDI/SD-SDI signal output and is  
equipped with two BNC output jacks (dual channel).  
Caution  
The AW-HHD870 can be installed only to the  
AW-HE870 settings can be used to switch between  
AW-HE870.  
HD-SDI and SD-SDI output.  
Standard accessories  
Screw (6 mm long) ............... ꢀ pcs  
Screw (Black, 8 mm long) ..... ꢁ pcs  
- 5 -  
Warning/Caution for safety  
WARNING  
CAUTION  
Refer all servicing to qualified personnel  
To reduce the risk of electric shock, don’t remove cover  
or back, unless you are a qualified personnel. Refer all  
mountings, connections, servicing to qualified service  
personnel.  
Do not drop the product, do not expose it to strong shock,  
or do not step on it, to prevent a fire and injuries.  
Do not install the product at a place full of moisture and  
dust, which may cause a fire and electric shock.  
No water or moisture inside  
Do not let water or moisture into the product, or expose it  
to moisture, to prevent a fire and electric shock.  
If you see smoke or smell an odor from the product, if  
water or other foreign matter gets inside, if it is damaged  
by dropping, or if you find anything wrong with it,  
immediately stop using it.  
Do not disassemble or modify the product to prevent  
a fire and electric shock.  
- 6 -  
Precautions  
Power off before connecting or disconnecting cables  
Before plugging or unplugging the cables, be sure to  
switch power off.  
Operating temperature range  
Avoid using the product at a cold place below 1ꢁ °F  
(–10 °C) or at a hot place above 113 °F (+ꢁ5 °C) because  
extremely low or high temperature will adversely affect  
the parts inside.  
Handle carefully.  
Do not drop the product, or subject it to strong shock or  
vibration. This is important to prevent trouble.  
Caution  
When the SDI card is to be discarded at the end of its  
service life, ask a specialized contractor to dispose of  
it properly in order to protect the environment.  
Avoid humidity and dust.  
Avoid using the product at a humid, dusty place because  
much humidity and dust will cause damage to the parts  
inside.  
- 7 -  
Major operating controls and their functions  
ZOOM/FOCUS connector  
SDI output connector [SDI OUT1, 2]  
This is the standard input connector for the lenses  
equipped with a remote control function for zoom focus.  
When using a Panasonic pan-tilt head (such as the  
AW-PH360, AW-PHꢁ00, AW-PHꢁ05 or AW-PH650), use  
the LENS I/F connector on the pan-tilt head instead of  
this connector.  
Serial digital component signal can be output.  
- 8 -  
Mounting  
1 Switch the camera off, and disconnect the power  
Caution  
connector and other cables from the camera.  
Be sure to ask your store, where you purchased the  
product, for mounting.  
Disconnect the camera power connector before  
mounting.  
2 Loosen the four screws on the rear of the camera and  
remove the rear panel.  
Before handling the card, touch a metal part of the  
camera to discharge the static from the human body.  
An anti-static wrist strap is recommended for added  
safety.  
If you touch the card while you are still charged with  
static, it may cause trouble.  
Keep the metal parts of the card free of contact with  
other metal parts.  
3 Loosen the two screws for the option card slot and  
remove the cover.  
4 Insert the SDI card along the guide rail at the bottom of  
the camera and the tab above. Insert it securely all the  
way.  
5 Tighten the two card setscrews securely.  
If you have lost the screws, use the screws (6 mm long)  
supplied as accessories.  
6 Fasten the rear panel with the four screws.  
If you have lost the screws, use the screws (Black, 8 mm  
long) supplied as accessories.  
7 Plug the cables back as necessary, connect the power  
connector, then switch power on.  
- 9 -  
Rear panel  
Option card slot  
cover  
Card setscrews  
(6 mm)  
Rear panel  
setscrews  
(8 mm)  
SDI card  
- 10 -  
Connection  
Before cable connection, switch power off.  
Use the AC adapter AW-PS510A for power supply. Use the power cable supplied with AW-HE870.  
For details on connecting individual devices, refer to the respective operating instructions.  
For details on operating individual devices, refer to the respective operating instructions.  
In case of using a remote operation panel AW-CB400  
Zoom lens  
Camera  
Video monitor,  
VIDEO IN  
VTR etc.  
Rear view of camera  
G/L OUT  
Sync generator  
Remote cable  
(for zoom/focus control)  
CONTROL  
IN/OUT  
Camera cable  
AW-CA50T8 or AW-CA50T9 +  
RS-232C/RS-422 converter  
VTR etc.  
Coaxial cable  
(BELDEN 8281  
or equivalent)  
DC Power Cable  
Remote operation panel  
AW-CB400  
HD-SDI: Max. 328 ft. (100 m)  
(BELDEN 1694)  
Unit with SDI input  
SD-SDI: Max. 656 ft. (200 m)  
(BELDEN 8281)  
AC adapter  
AW-PS510A  
AC adapter  
AW-PS510A  
- 11 -  
Appearance  
Unit: inch (mm)  
4-5/16 (109)  
3-3/4 (95)  
27/32  
(21.5)  
- 1ꢀ -  
Specifications  
Power requirements: 1ꢀ V DC (supplied from camera)  
Power consumption: Approx. ꢀ.ꢀ W  
indicates safety information.  
Allowable temperature ranges: For storage:  
–ꢁ °F to 1ꢁ0 °F (–ꢀ0 °C to +60 °C)  
For guaranteeing operation: 1ꢁ °F to +113 °F (–10 °C to +ꢁ5 °C)  
Operating humidity:  
Dimensions:  
30 % to 90 % (without condensation)  
ꢀ7/3ꢀ˝ ꢀ-3/ꢁ˝ ꢁ-5/16˝ [ꢀ1.5 (W) 70 (H) 109 (D) mm]  
Approx. 0.ꢀꢀ lbs. (0.1 kg)  
Weight:  
I/O connectors:  
SDI OUT1, SDI OUTꢀ connector (BNC)  
HD: Compliant with the SMPTEꢀ9ꢀM  
SD: Compliant with the SMPTEꢀ59M  
ZOOM/FOCUS connector 1ꢀ-pin; round  
Weight and dimensions indicated are approximate.  
Specifications are subject to change without notice.  
- 13 -  
PANASONIC BROADCAST & TELEVISION SYSTEMS COMPANY  
UNIT COMPANY OF PANASONIC CORPORATION OF NORTH AMERICA  
Headquarters:  
3 Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-5300  
EASTERN ZONE:  
3 Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7196  
WESTERN ZONE:  
3330 Cahuenga Blvd. West, Los Angeles, CA 90068 (323) 438-3608  
Government office:  
(201) 348-7587  
Broadcast PARTS INFORMATION & ORDERING:  
9:00 a.m. – 5:00 p.m. (PST) (800) 334-4881/24 Hr. Fax (800) 334-4880  
Emergency after hour parts orders (800) 334-4881  
TECHNICAL SUPPORT:  
Emergency 24 Hour Service (800) 222-0741  
Panasonic Canada Inc.  
5770 Ambler Drive, Mississauga, Ontario L4W 2T3 (905) 624-5010  
Corporativo Panasonic de México  
Moras No. 313, Col. Tlacoquemecatl del Valle, Del. Benito Juárez, México, Distrito Federal, C.P. 03200. 01 (55) 54 88 10 00  
Panasonic Puerto Rico, Inc.  
AVE 65de Inf, Km 9.5 Carolina, PR 00985 (787) 750-4300  
© Panasonic Corporation 2009  
Printed in Japan  

IBM BRUGERVEJLEDNING 8418 User Manual
IBM SYSTEM STORAGE DS5000 User Manual
I Tech Company Sunlight Readable LCD Monitor User Manual
JVC 0204MKH MW VP User Manual
JVC AV 29MT35 AV 29MT15 AV 29VA15 AV 21MT35 AV 21MT15 AV 21VA15 AV 25MT35 AV 25MT15 AV 25VA15 User Manual
JVC CRT Television AV 32230 User Manual
Linksys KX TG5571 User Manual
Philips 20PT2001 User Manual
Philips 28PT4473 User Manual
Philips DVD Player DVDR3475 User Manual