NEC PX 50XM4A User Manual

PlasmaSync Plasma Monitor

Model Information

For the operation of your plasma monitor,

refer to “Operation Manual”.

NEC Solutions (America), Inc.

Important Information

Warning

NOTE:

Not for use in a computer room as defined in the Standard

When you connect a computer to this monitor, use an RGB

for the Protection of Electronic Computer/ Data Processing

Equipment ANSI/NFPA 75.

cable including the ferrite core on both ends of the cable.

And regarding DVI and power cable, attach the supplied

ferrite cores. If you do not do this, this monitor will not

conform to mandatory FCC standards.

This equipment has been tested and found to comply with

the limits for a Class A digital device, pursuant to Part 15 of

the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when

the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct

the interference at his own expense.

Attaching the ferrite cores:

Set the ferrite cores on both ends of the DVI cable (not

supplied), and both ends of the power cable (supplied).

Close the lid tightly until the clamps click.

Use the band to fasten the ferrite core (supplied) to the

DVI cable.

DVI cable (not supplied)

Connector

band

core (small)

Power cable (supplied)

core (large)

Recommandations importantes

Avertissement

REMARQUE:

Pour raccorder un ordinateur à ce moniteur, procéder à

Ne pas utiliser dans une salle d’ordinateurs telle que définie

dans la Norme pour la protection des ordinateurs

l’aide d’un câble RGB à âme de ferrite aux deux

électroniques/appareils de traitement des données ANSI/

extrémités. Sur les câbles DVI et les câbles d’alimentation

NFPA75.

électrique, fixer les âmes de ferrite fournies aux extrémités.

Si vous ne le faîtes, le moniteur ne sera pas en

DOC avis de conformation

conformité avec les exigences des standards FCC.

Cet appareil numérigue de la Classe A respecte toutes les

Fixation des noyaux en ferrite.

exigences du Réglement sur le Matériel Brouilleur du Canada.

Monter les tores en ferrite aux deux extrêmités du câble

DVI (non fourni) et aux deux extrêmités du câble

d’alimentation électrique (fourni).

Fermez doucement le couvercle jusqu’à ce que les crans

se clipsent.

Fixer le tore en ferrite (fourni) au câble DVI à l’aide d’un

collier.

Câble DVI (non fourni)

Connecteur

Collier

noyau (petit)

Câble d'alimentation

électrique (fourni)

noyau (grande)

Specifications

Screen Size

43.5"(H)

24.5"(V) inches

1106(H)

622(V) mm

diagonal 50"

1.5"

(38)

2.3"

(58)

48.1" (1222)

Aspect Ratio

Resolution

Pixel Pitch

16 : 9

1365(H)

768(V) pixels

43.5" (1106)

0.032"(H)

0.032"(V) inches

0.81(H)

0.81(V) mm

Color Processing

Signals

4,096 steps, 68.7 billion colors

Synchronization Range Horizontal : 15.5 to 110 kHz

(automatic : step scan)

Vertical : 50.0 to 120 Hz

(automatic : step scan)

3.8"

(96)

Input Signals

RGB, NTSC (3.58/4.43), PAL (B,G,M,N),

PAL60, SECAM, HD*1 , DVD*1 , DTV*1

Units are in inch

(mm)

Bezel color is gray.

Input Terminals (VIDEO1 and RGB1 can also be used as OUTPUT terminals)

RGB

The features and specifications may be subject to change without

notice.

*¹HD/DVD/DTV input signals supported on this system

Visual 1 (Analog) mini D-sub 15-pin

Visual 2 (Analog) BNC (R, G, B, H/CS, V)

1*²

Visual 3 (Digital) DVI-D 24-pin

1*³

480P (60 Hz)

525I (60 Hz)

625P (50 Hz)

1035I (60 Hz)

480I (60 Hz)

576P (50 Hz)

625I (50 Hz)

1080I (50 Hz)

525P (60 Hz)

576I (50 Hz)

720P (60 Hz)

1080I (60 Hz)

Video

Visual 1

Visual 2

Visual 3

BNC

RCA-pin

S-Video: DIN 4-pin

*²The 5-BNC connectors are used as RGB/PC2 and HD/DVD2 input.

Select one of them under “BNC INPUT”.

*³Compatible with HDCP.

DVD/HD/DTV

Visual 1

Visual 2

Visual 3

Audio

External Control

RCA-pin (Y, PB[CB], PR[CR])

1*¹

BNC (Y, PB[CB], PR[CR])

1*^1,*²

DVI-D 24-pin

1*³

Supported Signals

• 640

480P @ 59.94/60Hz

• 1280

720P @ 59.94/60Hz

• 1920

1080I @ 59.94/60Hz

• 720

480P @ 59.94/60Hz

• 1440 (720)

480I @ 59.94/60Hz

• 1920

1080I @ 50Hz

• 720

576P @ 50Hz

• 1440 (720)

576P @ 50Hz

Stereo RCA

3 (Selectable)

D-sub 9-pin

1 (RS-232C)

9W+9W at 6 ohm

Sound output

Power Supply

Current Rating

Power Consumption

Dimensions

AC100-240V 50/60Hz

7.6A (maximum)

Note: In some cases a signal on the plasma monitor may not be displayed

properly. The problem may be an inconsistency with standards from

the source equipment (DVD, Set-top box, etc...). If you do experience

such a problem please contact NEC Solutions (America), Inc. and also

the manufacturer of the source equipment.

435W (typical)

48.1 (W)

30 (H)

3.8 (D) inches

1222 (W)

736 (H)

96(D) mm

Weight

97 lbs / 44 kg (without stand)

Environmental Considerations

Operating Temperature 0°C to 40°C / 32°F to 104°F

Humidity

Altitude

20 to 80% (no condensation)

0 to 9180 feet / 0 to 2800 m

Storage Temperature -10°C to 50°C / 14°F to 122°F

Humidity

Altitude

10 to 90% (no condensation)

0 to 9840 feet / 0 to 3000 m

Front Panel User Controls Power on/off, Input source select,

Volume up/down/ OSM control

Remote Control Functions Power on/off, Input source select, OSM

control,Volume up/down, Cursor (UP,

DOWN,LEFT, RIGHT), Pointer, Zoom up/

down, Off timer, Wireless/ Wired remote

control, Split screen buttons

Other Features Motion compensated 3D Scan Converter (NTSC,

PAL, 480I, 576I, 525I, 625I, 1035I, 1080I), 2-3

pull down Converter (NTSC, 480I, 525I, 1035I,

1080I (60Hz)), 2-2 pull down Converter (PAL,

576I, 625I, NTSC, 480I, 525I), Digital Zoom

Function (100-900% Selectable), Video Wall 4-25

multi screen, Self Diagnosis, Image Burn

OSM Functions Picture (Contrast/Brightness/Sharpness/ Color/Tint/

Picture mode/Noise reduction/Color temperature/

White balance/Gamma/Low tone/Color tune),

Audio (Bass/Treble/Balance/Audio input), Image

Adjust (Aspect mode/V-Position /H-Position/V-

Height /H-Width/Auto Picture/Fine picture/Picture

adjustment), Option1 (OSM/BNC Input/D-Sub

Input/RGB Select/HD Select/Input Skip/All Reset),

Option2 (Power management/Cinema mode/Long

life [PLE, Orbiter, Inverse, White, Screen wiper, Soft

focus]/Gray level/S1/S2/Picture size/DVI Set up/

CloseCaption/Caption cont), Option3 (Timer/Power

on mode/Control lock/IR Remote/Loop out/ID

number/Video wall [Divider, Position, Disp. mode,

Auto ID, Image adjust, Power on delay, PLE link,

Timer]), Option4 (Sub. P detect/Zoom nav/Pic

freeze/Seamless SW),Advanced OSM, Language*,

Color system, Source information

reduction tools (PLE LOCK1~3, INVERSE,

WHITE, ORBITER (Auto1,2/Manual), SCREEN

WIPER), Color Temperature select (high/mid/mid

low/low, user has 4 memories), Control lock

(Except power SW), Auto Picture, Input Skip,

Color Tune, Low Tone (3 mode), Auto ID,

Programmable Timer, Gamma Correction (4

mode), Loop through interface, Plug and play

(DDC1, DDC2b, RGB3: DDC2b only), Split

screen operations

Accessories

Regulations

Remote control with two AAA batteries, Power

cord, Manuals, Safety metal fittings, Ferrite cores,

Bands, Cable clamps

UL Approved (UL 60950-1, CAN/CSA C22.2

No.60950-1)

DOC Canada requirements

Meets FCC Class A requirements

*English, German, French, Italian, Spanish,

Swedish, Chinese, Russian

Table of Signals Supported

Supported resolution

•

When the screen mode is NORMAL, each signal is converted to a 1024 dots

768 lines signal. (Except for *^{2, 3, 4}

)

When the screen mode is TRUE, the picture is displayed in the original resolution.

When the screen mode is FULL, each signal is converted to a 1365 dots

768 lines signal. (Except for *³)

Computer input signals supported by this system

Sync Polarity

Horizontal Vertical Horizontal Vertical

Presence

Screen mode

Vertical

Horizontal

frequency frequency

(Hz) (kHz)

70.1 31.5

RGB

Dots

lines

Model

NORMAL TRUE FULL select*⁵

Memory

DVI

Signal Type

(4:3)

YES*²

YES

– –

(16:9)

YES YES

YES

640

400

– –

NEG

POS

NEG

POS

NEG

POS

NEG

POS

NEG

POS

NEG

POS

NEG

POS

NEG

POS

NEG

POS

NEG

POS

NEG

POS

NEG

POS

NEG

POS

NEG

POS

NEG

YES

– –

YES

– –

640

480

59.9

72.8

75.0

85.0

100.4

120.4

60.0

56.3

60.3

72.2

75.0

85.1

99.8

120.0

60.0

70.1

75.0

85.0

100.6

75.0

56.2

59.8

69.8

60.0

59.9

60.0

75.0

85.0

100.1

60.0

65.0

70.0

75.0

85.0

60.0

66.7

74.6

74.9

75.1

60.0

71.2

72.0

66.0

76.0

76.1

60.0

31.5

37.9

37.5

43.3

51.1

61.3

31.0

31.7

35.2

37.9

48.1

46.9

53.7

63.0

75.7

48.4

56.5

60.0

68.7

80.5

67.5

45.1

48.0

56.0

49.7

53.1

47.7

48.3

64.0

80.0

91.1

108.5

65.3

75.0

81.3

87.5

93.8

106.3

74.6

74.0

35.0

49.7

60.2

68.7

56.0

64.6

75.1

78.1

61.8

71.7

81.1

49.7

63.9

YES YES STILL

YES YES – –

YES YES STILL

YES YES

– –

848

480

852

480*¹

800

600

YES YES WIDE2

YES YES WIDE1

YES YES STILL

– –

YES

YES*³

YES

– –

YES YES

– –

IBM PC/AT*⁸

compatible

computers

1024

768

– –

YES STILL

YES – –

YES STILL

YES

– –

1152

864

YES STILL

YES WIDE1

YES WIDE3

YES WIDE1

YES WIDE2

1280

768

YES

– –

1280

768*⁹

1280

800*⁹

1280

854*⁹

1360

765

1360

768

1376

768

1280

1024

– –

– – YES*³WIDE1

YES

– –

YES WIDE2

YES STILL

YES*⁴

– –

YES

– –

1680

1050*⁹

YES WIDE4

YES

1600

1200

YES

– –

YES

– –

1920

1200*⁹

YES WIDE2

YES WIDE3

– –

YES

1920

1200RB

640

480

832

624

– –

YES

YES*³

YES

– –

YES*⁴

YES

YES*⁴

YES*³

YES*⁴

YES YES

– –

Apple

Macintosh*⁶*⁸

Sync on G Sync on G

NEG

– –

1024

768

1152

870

1440

900*⁹

1280

1024

– –

YES WIDE1

– –

YES

– –

NEG

– –

YES

– –

YES

– –

Work Station

(EWS4800)

Work Station(HP)

1280

1024

Work Station

1152

900

C Sync

– –

C Sync

– –

(SUN)

– –

1280

1024

768

1280

1024

– –

Work Station

(SGI)

– –

IDC-3000G

PAL625P

YES*⁷

– – YES*⁷

– – YES*⁷MOTION

– –

768

576

50.0

59.9

31.4

31.5

NEG

YES

NTSC525P

640

480

*1 Only when using a graphic accelerator board that is capable of displaying 852

480.

*2 This signal is converted to a 1024 dots

640 lines signal.

*3 The picture is displayed in the original resolution.

*4 The aspect ratio is 5:4. This signal is converted to a 960 dots

768 lines signal.

*5 Normally the RGB select mode suite for the input signals is set automatically. If the picture is not displayed properly, set the RGB mode

prepared for the input signals listed in the table above.

*6 To connect the monitor to Macintosh computer, use the monitor adapter (D-Sub 15-pin) to your computer's video port.

*7 Other screen modes (ZOOM and STADIUM) are available as well.

*8 When viewing a moving picture at a vertical frequency greater than 65Hz, the picture may sometimes be unstable (jumpy). If this occurs,

please set the refresh rate of the external equipment to 60Hz.

To view 480I@60Hz (480 interlaced lines, 60Hz refresh rate) or 576I@50Hz (567 interlaced lines, 50Hz refresh rate) when sync polarity

is “Sync on Green”, set “RGB SELECT” to “MOTION”.

*9 CVT standard compliant.

NOTE:

• While the input signals comply with the resolution listed in the table above, you may have to adjust the position and size of the picture or

the fine picture because of errors in synchronization of your computer.

• When a 1280 dots

1024 lines signal or 1600 dots

1200 lines signal is input to the monitor, the picture will be compressed.

• This monitor has a resolution of 1365 dots

768 lines. It is recommended that the input signal should be XGA, wide XGA, or equivalent.

• With digital input some signals are not accepted.

• The sync may be disturbed when a nonstandard signal other than the aforementioned is input.

• If you are connecting a composite sync signal, use the HD terminal.

What is HDCP/HDCP technology?

HDCP is an acronym for High-bandwidth Digital Content Protection. High bandwidth Digital Content Protection (HDCP) is a system for

preventing illegal copying of video data sent over a Digital Visual Interface (DVI).

If you are unable to view material via the DVI input, this does not necessarily mean the PDPis not functioning properly. With the implementation

of HDCP, there may be cases in which certain content is protected with HDCP and might not be displayed due to the decision/intention of the

HDCP community (Digital Content Protection, LLC).

• “IBM PC/AT” and “XGA” are registered trademarks of International Business Machines, Inc. of the United States.

• “Apple Macintosh” is a registered trademark of Apple Computer, Inc. of the United States.

NEC and the NEC logo are registered trademarks of

NEC Corporation

NEC Solutions (America), Inc.

1250 N. Arlington Heights Road, Suite 400

Itasca, Illinois 60143-1248

Printed on recycled paper

Printed in Japan

7S801361

JVC C 13311 User Manual
Magnavox 27MT5005D User Manual
MSi MSI Fuzzy Mainboard 945GM2 User Manual
Philips 21PT2304 User Manual
Philips 28PW9631 User Manual
Philips 190S7FB User Manual
Philips Brilliance 180P2M User Manual
Philips Computer Monitor 220S4L User Manual
Philips DVP3986K User Manual
Philips PR1308C User Manual