NEC PF 51V21 User Manual

COLOUR TELEVISION PF-51V21  
INSTRUCTIONS  
Thank you for your purchasing this NEC colour television.  
To ensure your complete understanding, please read this manual thoroughly  
before operation.  
Contents  
1. Specifications ………………….…. 1  
2. Important safeguard …………..… 2  
3. Television Installation ………..…..3  
4. Control Panel ……………….…….. 4  
5. Remote Control Hand Unit ….. 5  
6. Control Your TV ………………… 6  
7. Tuning Procedure………………. 9  
8. Menu Operation …..…………… 10  
9. Trouble Shooting ……………… 13  
1 Specification  
Television RF system  
Colour System  
B, G  
PAL, NTSC 3.58/4.43(AV input only)  
Channel and frequencies  
VHF Low channel (VL) =46.25 to 168.25 MHz  
VHF high channel (VH) =175.25 to 463.25 MHz  
UHF channel U)  
=471.25 to 863.25 MHz  
Power input  
AC 240V, 50/60 Hz  
Maximum 115W  
Power consumption  
Screen size  
Picture tube 55 cm  
Visible area 51 cm  
5 W + 5 W (Rated output)  
(5 cm x 9 cm ) oval x 2  
(measured diagonally)  
Audio output  
Speakers  
External input/output  
VIDEO inputs (RCA) at rear and front left  
AUDIO L/R inputs (RCA) at rear and front left  
S-Video input at rear  
VIDEO output (RCA) at rear  
AUDIO L/R output (RCA) at rear  
Headphone jack: mini jack (dia 3.5mm) at front left  
585 x 520 x 465  
Dimensions (WxHxD)  
Weight  
24.1 kg  
Accessories  
Remote control unit: RE-001 x 1  
AAA/ R03 /UM-4 dry battery x 2  
All specifications are subject to change without notice.  
3 Television Installation  
Connect antenna or video facility  
1.Use 75 Ωcoaxial cable plug or 300-75 Ωimpedance converter to plug in antenna input terminal on the rear  
of the cabinet.  
2.Connect the video facility to the audio, video in jack on the rear of the cabinet.  
VHF Antenna  
UHF Antenna  
Mixer  
Antenna in jack  
75Ωcoaxial cable  
VCR  
Audio out VCR)  
Video out VCR)  
Antenna in jack  
75Ωcoaxial cable  
Battery installation and replacement for remote control unit.  
The remote control unit uses two 1.5v AAA batteries. For battery installation and replacement see as  
follows:  
1.  
Turn the remote control unit upside down. Press  
down the grip of the battery compartment and  
slide the cover in the direction of the arrow.  
2. Install two new batteries, make sure that battery  
polarity matches with the (+)(-) marks inside the  
compartment, otherwise it would damage the unit.  
3. Close the battery compartment cover.  
4 Control Panel  
Front Controls  
Audio 2 (Left) Input  
Audio 2 (Right) Input  
Video 2 Input  
Earphone jack  
NOTE:  
When plug in to this  
earphone jack, sound  
from speakers would  
not be muted.  
MAIN SWITCH:  
MENU  
TV/AV  
Volume conontrol for  
the earphone can be  
Push this switch to turn Mains Power On.  
Push again to turn Mains Power Off.  
Power Indicator: When Mains Power On, this will be lit.  
Power ON: GREEN  
VOLUME UP/DOWN  
CHANNEL UP/DOWN  
done independently.  
Power OFF: RED  
ON-TIMER set: ORANGE  
Rear Terminals  
Remote Control Window:  
Receives the remote control signal.  
Antenna In(75Ω)  
Audio  
L
R
Video  
Video  
Audio Video Output  
Audio Video 1 Input  
S-Video Input  
L(Mono)  
R
5 Remote Control Hand Unit  
Please refer indicated pages.  
Power/Standby  
(Ref; P6)  
TV/AV Select  
TV/AV  
(Ref; P7)  
MENU  
P+  
(Ref.P10)  
Sound Volume Up/Down  
Channel Up/Down  
Ref; P6)  
V+  
V-  
MENU  
P-  
Ref; P6)  
Call  
(Ref.P7)  
Mute  
(Ref.P7)  
CALL  
Child Lock  
(Ref.p8)  
SLEEP  
LOCK  
Quick View  
(Ref.p7)  
QV  
Direct Access Numeric  
Keys  
1
2
3
6
Channel Scan  
(Ref.P7)  
SCAN  
ZOOM  
(Ref.P6)  
4
7
5
8
ZOOM  
(Ref.P6)  
-
9
|  
|ꢂ  
Picture Effect  
(Ref.P8)  
0
- / --  
Picture MENU  
(Ref.P12)  
Surround Sound  
Effect  
| |ꢂ  
(Ref.P8)  
Sound effect  
(Ref.P8)  
Sound MENU  
(Ref.P12)  
RE-001  
6 CONTROL YOUR TV  
6-1 MAIN Power ON/OFF  
This switch will turn the television ON/OFF totally.  
With Mains status On, you can also turn off using Remote Control Hand Set.  
This status is called Stand-By mode.  
In this mode;  
You can also turn ON the TV by pushing the Channel Up/Down keys on the front controls.  
The TV has an Automatic Power OFF function. With No Signal condition, the TV will automatically turn OFF  
after 10 min.  
6-2  
Channel Up/Down  
3
P+  
P-  
2
Push [P+] key, to change Channel Up  
Push [P-] key, to change Channel Down.  
PROG  
1
PAL  
6-3  
Direct Access Tuning  
Using the numeric keys on Remote Control Hand  
Piece, Channels can be selected directly.  
Or repeatedly press the “-/--” button, to select  
the desired mode then press numeric buttons.  
1
X Y Z  
[ \ ]  
^ _ `  
-/--  
“-“  
1 digit mode  
W z  
“—“  
“1--“  
2 digit mode  
3 digit mode (Max Ch. 129)  
6-4  
Volume Control  
Push [V+] key, for Volume Up  
Push [V-] key, for Volume Down  
V-  
V+  
VOLUME  
┃┃···  
5  
6-5  
ZOOM  
Push [ZOOM] key, to change as follows:  
ZOOM  
NORMAL WIDE ZOOM  
WIDE — picture height is reduced.  
ZOOM — picture height is expanded.  
6-6  
6-7  
MUTE  
By pushing this key, sound output will be muted.  
Push [MUTE] again, or Volume Up/Down, and  
sound Volume will return.  
X
MUTE  
S-Video  
TV/AV Selection  
AV2  
You can select your video  
source by the [TV/AV] key.  
AV1  
TV/AV  
TV/AV  
3
PAL  
TV  
6-8  
QUICK VIEW  
TV Mode: Channel will quickly return to the previous Channel being  
10  
QV  
watched.  
2
2
AV Mode: Back to TV channel  
AV1  
6-9  
Channel Scanning  
By pushing this key, Channels will change automatically  
SCAN  
Each channel will be previewed for 3 seconds, and stop at original channel.  
Skipped channels will not be previewed.  
6-10  
CALL  
CALL  
This key will call the On screen display.  
Push again, to remove the on screen display.  
Channel No.  
1
Colour system  
AUTO  
OFF Timer and clock  
These two options appear after  
being set.)  
SLEEP  
57  
clock  
4:09  
6-11  
Picture EFFECT  
By repeatedly pushing this key, picture  
effects will change as follows.  
STANDARD  
RICH  
SOFT  
PERSONAL  
STANDARD  
TINT setting is not included.  
Personal is the last setting made by you.  
6-12  
SOUND EFFECT  
By repeatedly pushing this key, sound  
| |ꢂ  
NORMAL  
effects will change as follows:  
PERSONAL  
ROCK  
POP  
JAZZ  
NORMAL  
6-13  
SURROUND SOUND EFFECT  
By repeatedly pushing this key,  
surround sound effects will change as follows:  
SPACE  
SPACE  
HALL  
THEATRE  
SURROUND OFF  
6-14  
LOCK  
By pushing the [LOCK] key,  
LOCK  
the lock screen will appear.  
CHILD LOCK  
OFF  
By pushing this key again for over 3 seconds  
continuously, LOCK situation will change.  
In “LOCK On” status, front panel buttons  
will be locked, except when turned off by  
the same [LOCK] procedure.  
7 Tuning procedure  
7-1 Auto Search Function: Automatic Search and Memory (ASM) is available for program installation from  
Antenna input.  
Using[MENU]key on the front or [MENU] key  
PRESET  
ASM  
on the Remote for ASM.  
POSITION  
BAND  
SKIP  
8
A. Push [MENU] key repeatedly to select “PRESET”  
B. Push [P+] or [P-] keyto select “ASM”  
C. Push [V+] or [V-] key, to start ASM .  
and memorize into program list (0~129).  
D. Wait until function has finished.  
UHF  
OFF  
ON  
AFT  
FINE TUNING  
SEARCH  
SWAP  
|||·I······  
7-2 SEARCH  
PRESET  
ASM  
POSITION  
BAND  
SKIP  
AFT  
A. Push [MENU] key repeatedly to select “PRESET”.  
B. Using [P+] or [P-] key, select POSITION.  
Using [V+] or [V-] or numeric keys to change POSITION  
Number.  
8
UHF  
OFF  
ON  
FINE TUNING  
SEARCH  
SWAP  
C. Push [P+] or [P-] key to select BAND.  
Push [V+] or [V-] key to change BAND.  
D. Push [P+] or [P-] key to select SEARCH.  
E. Push [V+] or [V-] key to start search.  
F. Wait until function has finished.  
|||·I······  
7-3 FINE TUNING  
A. Push [MENU] key repeatedly to select “PRESET”.  
B. Using [P+] or [P-] key, select POSITION.  
Using [V+] or [V-] change POSITION.  
PRESET  
ASM  
POSITION  
BAND  
SKIP  
AFT  
FINE TUNING  
SEARCH  
SWAP  
8
UHF  
OFF  
ON  
C. Using [P+] or [P-] key, select FINE TUNING.  
D. Using [V+] or [V-] key, adjust for best tuning.  
|||·I······  
7-4 AFT Function: Automatic Fine Tuning  
Keep Tuning at the best position., always.  
A. Push [MENU] key repeatedly to select “PRESET”.  
B. Using [P+] or [P-] key, select AFT,  
Using [V+] or [V-] key, to set AFT ON or OFF.  
7-5 SKIP Function: Use to “SKIP” Channels. After setting to “ON”, the channel will not  
be selected by Channel Up/Down keys.  
A. Push [MENU] key repeatedly to select “PRESET”  
B. Using [P+] or [P-] key, select “POSITION”.  
Using [V+] or [V-] key, change POSITION.  
PRESET  
ASM  
POSITION  
BAND  
SKIP  
AFT  
FINE TUNING  
SEARCH  
SWAP  
8
UHF  
OFF  
ON  
C. Using [P+] or [P-] key, select SKIP.  
Using [V+] or [V-] key, select ONor OFF.  
|||·I······  
7-6 SWAP Function: Program Number and Channel exchange  
A. Push [MENU] key repeatedly to select “PRESET”.  
B. Using [P+] or [P-] key, select “SWAP”.  
PRESET  
ASM  
POSITION  
BAND  
:
:
8
Using [V+] or [V-] key, enter to SWAP.  
UHF  
SKIP  
AFT  
FINE TUNING  
SEARCH  
SWAP  
:
:
OFF  
ON  
C. Using [P+] or [P-] key, select “PROGRAM A”  
orPROGRAM B.  
D. Using [V+] or [V-] key or numeric keys, change  
“PROGRAM A ” or “PROGRAM B ”.  
E. Pushing [P+] or [P-] key, select “EXCHANGE”  
Push [V+] or [V-] key repeatedly until “OK” is displayed  
on screen. PROGRAM A and PROGRAM B are exchanged.  
|||·I······  
PROGRAM EXCHANGE  
PROGRAM A  
PROGRAM B  
EXCHANGE  
6
2
OK  
8 Menu Operation  
8-1 [MENU] key on front  
TV mode : Push [MENU] key continuously, to scroll through the MENU selection, as follows.  
PICTURE SOUND TIME SETUP PRESET NORMAL  
AV mode : Push [MENU] key continuously, to scroll through the MENU selection, as follows.  
PICTURE SOUND TIME SETUP NORMAL  
8-2 [MENU] key on the remote handset  
TV mode : [MENU] key selects as follows:  
TIME  
SETUP  
PRESET  
NORMAL  
10  
AV mode [MENU] key selects as follows:  
TIME  
SETUP  
NORMAL  
8-3 TIME  
(The ON/OFF timer cannot be set unless the clock has already been set.)  
A. Select “TIME” with the [MENU] key.  
Using the [P+]/[P-] key, select the item.  
B. Using the [P+]/[P-] key, select “CLOCK”, “OFF-TIME”  
or “ON-TIME”  
TIME  
CLOCK  
OFF-TIME  
ON-TIME  
POSITION  
ALARM  
-- :--  
-- :--  
-- :--  
-
C. Using the [V+] key, minutes will increase from “00” to “59”.  
Using the [V-] key, hours will increase as follows;  
“0,1…23,----”  
--  
D. Using [P+]/[P-] keys, select “POSITION”  
Using [V+]/[V-] keys, change POSITION.  
E. Using [P+]/[P-] keys, select “ALARM”  
Using [V+]/[V-] keys, ALARM timer can be set.  
After presetting, preset time has come, alarm symbol will be displayed on screen.  
The timer can be set “0” to “90” Minutes.  
8-4 SETUP  
Setup your TV as your favorite  
SETUP  
A. Using the [MENU] key, select SETUP.  
Using the [P+]/[P-] keys, select the item.  
B. Using [P+]/[P-] keys, select “BLUE BACK” or “C-SYS” .  
C. Using the [V+] or [V-] keys, change to ON or OFF.  
D. Pushing [P+]/[P-], select “C-SYS”.  
BLUE BACK  
C-SYS  
ON  
AUTO  
Using the [V+]/[V-] keys, the colour system will be  
changed as follow:  
TV MODE  
AUTO PAL N4.43 N3.58  
AV MODE  
AUTO PAL N4.43 N3.58  
11  
8-5 PICTURE MENU Function: Brightness, Contrast, Colour Sharpness, Tint  
PICTURE  
BRIGHT  
32  
32  
42  
32  
32  
CONTRAST  
COLOUR  
SHARP  
A. By pushing the  
key, Picture Menu will appear.  
B. Select each function using the [P+]/[P-] keys.  
C. Each value can be controlled by the [V+]/[V-] keys.  
D. Repeat any functions if required.  
TINT  
32  
┃┃┃·····  
NOTE: TINT control will be appeared only if a NTSC signal is being received.  
8-6 SOUND MENU  
Function: Bass, Treble, Balance.  
SOUND  
BASS  
A.  
A. By pushing the  
key, Sound Menu will appear.  
32  
32  
00  
B. Select each function using the [P+]/[P-] keys.  
C. Each value can be controlled by the [V+]/[V-] keys.  
D. Repeat any functions if required.  
TREBLE  
BALANCE  
HEADPHONE  
HEADPHONE VOL  
ON  
32  
32  
┃┃┃·····  
12  
9 Trouble Shooting  
Before arranging for service, firstly know the status and then check simply as follows:  
Problems  
Check  
No picture or sound.  
Check if the power supply is plugged in.  
Check if the power switch is in “on’” position.  
Check if the volume control is set to the minimum or mute position.  
Check if the power switch is in “on” position.  
Check if the batteries are out of use or not connected well.  
Make sure that there is no strong light striking the sensor window of  
remote control unit.  
Picture is OK, no sound.  
Remote control doesn’t work.  
Check there are no obstacles between the sensor window and remote  
control unit.  
No TV signal.  
Check if the TV/AV button is not set to TV status.  
Check if the antenna is well connected.  
Check if you installed the TV correctly.  
No external video signal.  
Check if you installed the TV correctly.  
Check if the TV/AV button is set to AV position.  
Picture lacks colour or picture Check colour, brightness and contrast controls are correctly adjusted.  
too dark.  
All  
channels  
lose  
colour Check if the antenna is broken.  
Check if the antenna is disconnected.  
Check if the antenna is damaged.  
intermittently.  
Poor reception, loss of colour Check if channels are correctly tuned (see “Fine tuning”).  
with certain channels.  
Diagonal stripes appear on The receiver may be affected by interference (e.g. from nearby radio  
picture.  
broadcasting transmitter or from another TV receiver).  
Check if the antenna is broken.  
Picture has “snow”.  
Check if the antenna is disconnected.  
Check if the antenna is damaged.  
Ghost images appear.  
Check if the antenna direction has been changed by a storm or strong  
wind, etc. (because ghost images are caused by the arrival at the  
antenna of both the signal which has traveled directly from the  
transmitter and the signal which has been reflected from a hill or a large  
building. The direction of the antenna should be chosen for minimized  
ghosting.)  
13  
NEC Australia Pty. Ltd.  
ABN 14 004 803 490  
Home Electronics Group  
NEC Service Centres  
NEW South Wales  
Sydney  
184 Milperra Rd, Revesby 2212  
(02)9780 8688  
(02)4926 2466  
Newcastle  
120 Parry Street, Newcastle West 2302  
Victoria  
Melbourne  
480 Princes Highway, Noble Park 3174  
(03)9554 6245  
Queensland  
Brisbane  
116 Ipswich Rd, Woollongabba 4102  
Shop 1, 48 Ferry Rd, Southport 4215  
(07)3361 5858  
(07)5591 3670  
Southport  
South Australia  
Adelaide  
84A Richmond Road, Keswick, 5053.  
45 Sarich Court, Osborne Park 6017  
(08)8375 5710  
(08)9446 5333  
Western Australia  
Perth  
For Service in outer areas, please contact your NEC retailer for the address of the nearest Authorized NEC Service  
Centre.  
NEC Australia Pty., Ltd.  
244 Beecroft Road EPPING 2121  
Tel. 131-632 Fax. (02) 9930 2380  
14  

KitchenAid KECC508RPT02 User Manual
Lenovo THINKCENTRE 4496 User Manual
Melissa 650 004 User Manual
MSi FUZZY CX700D User Manual
NEC MULTISYNC LCD2690WUXI User Manual
NEC XV17+ User Manual
Pelco PMCS17A User Manual
Philips Cordless Telephone CD485 User Manual
Philips HTS335W User Manual
Philips MGD203 User Manual