MultiSync LCD4010
40" LCD Colour Monitor
MultiSync LCD4610
46" LCD Colour Monitor
User’s Manual
DECLARATION OF CONFORMITY
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
U.S. Responsible Party: NEC Display Solutions of America, Inc.
Address:
500 Park Boulevard, Suite 1100
Itasca, Illinois 60143
(630) 467-3000
Tel. No.:
Type of Product:
Computer Monitor
Equipment Classification: Class B Peripheral
Model: MultiSync LCD4010 (L404G6) / MultiSync LCD4610 (L464G7)
We hereby declare that the equipment specified above
conforms to the technical standards as specified in the FCC Rules.
Windows is a registered trademark of Microsoft Corporation. NEC is a registered trademark of NEC Corporation.
OmniColor is a registered trademark of NEC Display Solutions Europe GmbH in the countries of EU and Switzerland.
All other brands and product names are trademarks or registered trademarks of their respective owners.
Canadian Department of Communications Compliance Statement
DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.2 No. 60950-1.
FCC Information
1. Use the attached specified cables with the MultiSync LCD4010 (L404G6) / MultiSync LCD4610 (L464G7) colour monitor so as
not to interfere with radio and television reception.
(1) Please use the supplied power cord or equivalent to ensure FCC compliance.
(2) Please use the supplied shielded video signal cable, 15-pin mini D-SUB to 15-pin mini D-SUB.
(3) Please attach the ferrite cores on the Audio Cable. Please see page 12 of this manual.
2. ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice, pursuanttopart15oftheFCCRules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult your dealer or an experienced radio/TV technician for help.
If necessary, the user should contact the dealer or an experienced radio/television technician for additional suggestions. The user
may find the following booklet, prepared by the Federal Communications Commission, helpful: “How to Identify and Resolve Radio-
TV Interference Problems.” This booklet is available from the U.S. Government Printing Office, Washington, D.C., 20402, Stock No.
004-000-00345-4.
English-1
Important Information
WARNING
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT
USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS
THE PRONGS CAN BE FULLY INSERTED.
REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM
WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE
POWER CORD FROM THE AC OUTLET. DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause
electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit.
This symbol alerts the user that important literature concerning the operation and maintenance of this unit
has been included. Therefore, it should be read carefully in order to avoid any problems.
Declaration
Declaration of the Manufacturer
We hereby certify that the colour monitor MultiSync
LCD4010 (L404G6) / MultiSync LCD4610 (L464G7)
and marked with
is in compliance with
Council Directive 73/23/EEC:
– EN 60950-1
Council Directive 89/336/EEC:
– EN 55022
NEC Display Solutions, Ltd.
4-13-23, Shibaura,
Minato-Ku
Tokyo 108-0023, Japan
– EN 61000-3-2
– EN 61000-3-3
– EN 55024
Disposing of your old NEC product
Within the European Union
EU-wide legislation, as implemented in each Member State, requires that waste electrical and
electronic products carrying the mark (left) must be disposed of separately from normal household
waste. This includes monitors and electrical accessories, such as signal cables or power cords. When
you need to dispose of your NEC display products, please follow the guidance of your local authority,
or ask the shop where you purchased the product, or if applicable, follow any agreements made
between yourself and NEC.
The mark on electrical and electronic products only applies to the current European Union Member
States.
Outside the European Union
If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local
authority so as to comply with the correct disposal method.
English-2
Safety Precautions, Maintenance & Recommended Use
FOR OPTIMUM PERFORMANCE, PLEASE NOTE
THE FOLLOWING WHEN SETTING UP AND USING
THE MULTISYNC LCD4010 / MULTISYNC LCD4610
LCD COLOUR MONITOR:
Immediately unplug your monitor from the wall outlet and refer
servicing to qualified service personnel under the following
conditions:
•
•
When the power supply cord or plug is damaged.
•
DO NOT OPEN THE MONITOR. There are no user
serviceable parts inside and opening or removing covers
may expose you to dangerous shock hazards or other risks.
Refer all servicing to qualified service personnel.
If liquid has been spilled, or objects have fallen into the
monitor.
•
•
•
If the monitor has been exposed to rain or water.
If the monitor has been dropped or the cabinet damaged.
•
•
Do not spill any liquids into the cabinet or use your monitor
near water.
If the monitor does not operate normally by following
operating instructions.
Do not insert objects of any kind into the cabinet slots, as
they may touch dangerous voltage points, which can be
harmful or fatal or may cause electric shock, fire or
equipment failure.
Recommended Use
•
•
For optimum performance, allow 20 minutes for warm-up.
Rest your eyes periodically by focusing on an object at least
5 feet away. Blink often.
•
•
Do not place any heavy objects on the power cord.
Damage to the cord may cause shock or fire.
•
•
•
•
Position the monitor at a 90° angle to windows and other
light sources to minimize glare and reflections.
Do not place this product on a sloping or unstable cart,
stand or table, as the monitor may fall, causing serious
damage to the monitor.
Clean the LCD monitor surface with a lint-free, non-abrasive
cloth. Avoid using any cleaning solution or glass cleaner!
•
•
When operating the MultiSync LCD4010 / MultiSync LCD4610
LCD monitor with its AC 220-240V power supply in Europe,
use a power supply cord provided with the monitor.
Adjust the monitor’s brightness, contrast and sharpness
controls to enhance readability.
Avoid displaying fixed patterns on the monitor for long
periods of time to avoid image persistence (after image
effects).
In UK, use a BS-approved power cord with molded plug
having a black (13A) fuse installed for use with this monitor.
If a power cord is not supplied with this monitor, please
contact your supplier.
•
Get regular eye checkups.
•
•
When operating the MultiSync LCD4010 / MultiSync LCD4610
with a 220-240V AC power source in Australia, use the power
cord provided with the monitor. If a power cord is not supplied
with this equipment, please contact your supplier.
Ergonomics
To realize the maximum ergonomic benefits, we recommend the
following:
•
Use the preset Size and Position controls with standard
signals.
For all other cases, use a power cord that matches the AC
voltage of the power outlet and has been approved by and
complies with the safety standard of your particular country.
•
•
•
Use the preset Colour Setting.
Use non-interlaced signals.
•
•
Do not place any objects onto the monitor and do not use
the monitor outdoors.
Do not use primary colour blue on a dark background, as it
is difficult to see and may produce eye fatigue due to
insufficient contrast.
The inside of the fluorescent tube located within the LCD
monitor contains mercury. Please follow the bylaws or rules
of your municipality to dispose of the tube properly.
•
•
Do not bend power cord.
Do not use monitor in high temperature, humid, dusty, or
oily areas.
•
•
If monitor or glass is broken, do not come in contact with the
liquid crystal and handle with care.
Allow adequate ventilation around the monitor, so that heat
can properly dissipate. Do not block ventilated openings or
place the monitor near a radiator or other heat sources.
Do not put anything on top of the monitor.
•
The power cable connector is the primary means of
detaching the system from the power supply. The monitor
should be installed close to a power outlet, which is easily
accessible.
•
•
•
Handle with care when transporting. Save packaging for
transporting.
Please clean the holes of back cabinet to reject dirt and
dust at least once a year because of set reliability.
If using the cooling fan continuously, it’s recommended to
wipe holes a minimum of once a month.
English-3
Contents
Your new MultiSync LCD4010 / MultiSync LCD4610 monitor box* should contain the following:
•
•
•
•
•
•
•
•
LCD monitor
•
•
•
•
•
•
Band x 2
Power Cord (3m)
Ferrite Core x 2
Video Signal Cable — SC-B113 (4m)
User’s Manual
Speaker Plug x 1set (Required for optional Loudspeakers)
Stand for the Independence x 2
Thumbscrew for stand x 2
Main switch cover
Wireless Remote Control and AA Batteries
Clamper x 3
Screw (M4 x 8) x 4
CD-ROM
Thumbscrew
for stand x 2
Stand for the
Independence x 2
Power Cord
Video Signal Cable
(D-SUB to D-SUB Cable)
Main switch cover
Clamper x 3
Screw (M4 x 8) x 4
Speaker Plug x 1set
(Required for optional
Loudspeakers)
(Attached on external
speaker terminal)
Ferrite Core x 2
CD-ROM
User’s Manual
Wireless Remote Control
and AA Batteries
Band x 2
*
*
Install the stands at the time of unpacking if the display will be used with the stand.
Remember to save your original box and packing material to transport or ship the monitor.
The following components are prepared as option.
External Speaker Unit
•
English-4
Parts Name and Functions
Control Panel
9
EXIT
INPUT
MUTE
10
Button Location
ON
EXIT
INPUT
MUTE
OFF
5
8
7
6
4
3
2
1
1
POWER button (
)
7
DOWN ( ) button
Switches the power on/off. See also page 18.
Activates the OSM menu when the OSM menu is turned-off.
Acts as button to move the highlighted area down to
select the adjustment with OSM menu.
2
MUTE button
Switches the audio mute ON/OFF.
8
EXIT button
Activates the OSM menu when the OSM menu is turned-off.
Acts as EXIT button to move to previous menu with OSM
menu.
3
INPUT button
Acts as SET button within OSM menu. (Toggle switches
between [RGB1], [RGB2], [RGB3], [DVD/HD], [VIDEO] or
[VIDEO<S>]). [VIDEO<S>] is enabled by selecting the
“SEPARATE” mode in the OSM or by having the “S-VIDEO”
cable connected with the “S-VIDEO” signal present and
selecting “PRIORITY” MODE. See page 26.
9
Remote control sensor and Power Indicator
Receives the signal from the remote control (when using the
wireless remote control). See also page 8.
Glows green when the LCD monitor is in active and glows
red when the LCD monitor is in POWER OFF mode. When
the LCD monitor is in POWER SAVE mode, it will glow both
green and red. When SCHEDULE is enabled, it will blink
green and glow red. See page 19.
4
PLUS (+) button
Acts as (+) button to increase the adjustment with OSM menu.
Increases the audio output level when the OSM menu is
turned off.
In the case of where a failure is detected, it will blink red.
Main Power Switch
10
5
MINUS (-) button
On/off Switch to turn main power on/off.
Acts as (-) button to decrease the adjustment with OSM menu.
Decreases the audio output level when the OSM menu is
turned off.
Control Key Lock Mode
This control completely locks out access to all Control Key
functions. To activate the control key lock function, press both
of “ ” and “ ” and hold down simultaneously for more than
6
UP ( ) button
Activates the OSM menu when the OSM menu is turned-off.
Acts as button to move the highlighted area up to select
the adjustment with OSM menu.
3 seconds. To resume back to user mode, press both of “
”
and “ ” and hold simultaneously for more than 3 seconds.
English-5
Terminal Panel
1
AC IN connector
7
AUDIO IN 1, 2, 3
Connects with the supplied power cord.
To input audio signal from external equipment such as a
computer, VCR or DVD player.
2
RGB 1 IN (DVI-D)
8
AUDIO OUT
To input digital RGB signals from a computer or HDTV
device having a digital RGB output.
To output the audio signal from the AUDIO IN 1, 2 and 3 jack.
* This connector does not support analog input.
9
VIDEO INPUT/OUTPUT CONNECTOR
VIDEO IN connector (BNC and RCA): To input a composite
video signal. BNC and RCA connectors are not available at
the same time. (Use only one input).
VIDEO OUT connector (BNC): To output the composite
video signal from the VIDEO IN connector.
3
RGB 2 IN (mini D-Sub 15 pin)
To input analog RGB signals from a personal computer or
other RGB equipment.
S-VIDEO IN connector (DIN 4 pin): To input the S-video
(Y/C separate signal). See page 26, S-VIDEO MODE
SETTING.
4
RGB 3 [R, G, B, H, V] (BNC)
IN connector: To input analog RGB signals or signals from
other RGB equipment.
This is also to connect equipment such as a DVD player and
HDTV laser disk player. A Sync-on-Green signal can be
connected to the G connector.
EXTERNAL CONTROL (mini D-Sub 9 pin)
10
IN connector: Use when operating the LCD monitor from
the RGB equipment like a computer.
Out connector: To connect multiple MultiSync LCD4010 /
MultiSync LCD4610.
5
RGB OUT connector (BNC)
To output the signal from RGB 3.
EXTERNAL SPEAKER TERMINAL
11
To output the audio signal from AUDIO 1, 2 or 3 jack.
6
DVD/HD connector (BNC)
Connecting equipment such as a DVD player, HDTV device,
or Laser disc player.
English-6
Wireless Remote Control
6
MUTE button
To switch the mute function on/off.
7
VOLUME UP button
Increases the audio output level.
8
VOLUME DOWN button
Decreases the audio output level.
9
PIP (Picture In Picture) button
ON/OFF button: Toggle switches between PIP, POP,
side-by-side (aspect) and side-by-side (full).
See page 23.
INPUT button: Selects the “picture in picture” input signal.
CHANGE button: Replaces to the main picture and sub
picture.
STILL button
10
11
ON/OFF button: To switch the still picture mode on/off.
CAPTURE button: Captures the new picture.
Note: Still does not work when pixel clock is greater than
108MHz.
DISPLAY button
To switch the information OSM on/off. See page 19.
AUTO SETUP button
12
To enter the auto setup menu. See page 23.
MENU button
13
To switch the menu mode on/off.
UP button
14
Acts as button to move the highlighted area up to select
the adjustment with OSM menu.
Small screen which adjusted “PIP” mode moves up.
1
POWER button
Switches the power on/off.
DOWN button
15
* If Power Indicator is not glowing, then no controls will work.
Acts as button to move the highlighted area down to
select the adjustment with OSM menu.
2
INPUT button
Small screen which adjusted “PIP” mode moves down.
Selects from input signal, [RGB1], [RGB2], [RGB3],
[DVD/HD], [VIDEO] and [VIDEO<S>].
[VIDEO<S>] is enabled by selecting the “SEPARATE” mode
in the OSM or by having the “S-VIDEO” cable connected
with the “S-VIDEO” signal present and selecting “PRIORITY”
MODE. See page 26.
MINUS button decrease
16
Acts as (-) button to decrease the adjustment with OSM
menu.
Small screen which adjusted “PIP” mode moves left.
PLUS button increase
17
3
AUDIO INPUT button
Acts as (+) button to increase the adjustment with OSM
menu.
Small screen which adjusted “PIP” mode moves right.
Selects from input audio signal, [AUDIO1], [AUDIO2],
[AUDIO3].
4
SIZE button
SET button
18
Selects picture size, [FULL], [NORMAL], [WIDE] and [ZOOM].
See page 19.
Acts as SET button with OSM menu.
EXIT button
19
5
PICTURE MODE button
Turn to previous menu with OSM menu.
Selects from picture mode, [HIGHBRIGHT], [STANDARD],
[sRGB], [CINEMA]. See page 19.
HIGHBRIGHT: for moving images such as DVD
STANDARD: for images
sRGB: for text based images
CINEMA: for movies.
English-7
Operating Range for the Remote Control
Point the top of the remote control toward the LCD monitor’s
remote sensor during button operation.
Handling the remote control
Use the remote control within a distance of about 7 m/23 ft.
from the front of the LCD monitor’s remote control sensor
and at a horizontal and vertical angle of within 30° within a
distance of about 3 m/10 ft.
*
*
Do not subject to strong shock.
Do not allow water or other liquid to splash the remote
control. If the remote control gets wet, wipe it dry
immediately.
*
*
Avoid exposure to heat and steam.
Other than to install the batteries, do not open the
remote control.
Caution: Important, the remote control system may not
function when direct sunlight or strong
illumination strikes the remote control sensor of
the LCD monitor, or when there is an object in
the path.
English-8
Setup Procedure
1. Determine the installation location
CAUTION: DO NOT ATTEMPT TO INSTALL THE LCD
3. Connect external equipment
(See pages 12-17)
MONITOR BY YOURSELF.
•
To protect the connected equipment, turn off the main
power before making connections.
Installing your LCD display must be done by a qualified
technician. Contact your dealer for more information.
•
Refer to your equipment user manual.
4. Connect the supplied power cord
CAUTION: MOVING OR INSTALLING THE LCD MONITOR
MUST BE DONE BY TWO OR MORE PEOPLE.
•
The power outlet socket should be installed as near to
the equipment as possible, and should be easily
accessible.
Failure to follow this caution may result in injury if the LCD
monitor falls.
•
•
Fully insert the prongs into the power outlet socket.
Loose connection may cause noise.
CAUTION: Do not mount or operate the display upside
down, face up, or face down.
Please fix the power cord by attaching the screw and
clamper.
CAUTION: This LCD has a temperature sensor and cooling
fan. If the LCD becomes too hot, the cooling fan
will turn on automatically. If the LCD becomes
overheated and the cooling fan is running, the
“Caution” menu will appear. If the “Caution”
menu appears, discontinue use and allow the
unit to cool. When the LCD monitor is used in an
enclosure or with protection on LCD surface,
please check the inside temperature of monitor
by “HEAT STATUS” (See page 28). The
NOTE: Please refer to “Safety Precautions, Maintenance &
Recommended Use” section of this manual for
proper selection of AC power cord.
Screw
Clamper
temperature is too hot than normal condition,
please set “cooling fan” to ON on SCREEN
SAVER function (See page 24).
IMPORTANT: Lay the protective sheet, which was wrapped
around the LCD monitor when it was
packaged, beneath the LCD monitor so as
not to scratch the panel.
2. Install the remote control batteries
The remote control is powered by 1.5V AA batteries.
To install or replace batteries:
Screw hole for clamper
1. Press and slide to open the cover.
2. Align the batteries according to the (+) and (–)
indications inside the case.
3. Replace the cover.
5. Switch on the power of all attached
external equipment
When connected with a computer, switch on the power of
the computer first.
CAUTION: Incorrect use of batteries can result in leaks
6. Operate the attached external equipment
Display the signal on the external equipment you wish.
or bursting.
Be careful especially about the following points.
7. Adjust the sound
Make adjustments when adjustment of the volume is
required.
•
Place “AA” size batteries matching the + and - signs on
each battery to the + and - signs of the battery
compartment.
•
•
Don’t mix battery types.
8. Adjust the screen (See pages 20-28)
Make adjustments when adjustment of the screen display
position or distortion is required.
Don’t combine new batteries with used ones.
It causes shorter battery life or leakage of batteries.
•
Remove dead batteries immediately to prevent battery
liquid from leaking into the battery compartment.
9. Adjust the image (See pages 20-28)
Don’t touch exposed battery acid, it cause damage to
your skin.
Make adjustments when picture adjustment such as the
brightness or contrast is required.
NOTE: If you do not intend to use the Remote Control for a
long period, remove the batteries.
English-9
10. Recommended Adjustment
To reduce the risk of “image persistence”, please adjust the
following items based on the application being used.
“SCREEN SAVER” (See page 24), “SIDE BORDER COLOR”
(See page 24), “DATE & TIME” (See page 28), “SCHEDULE”
(See page 28).
11. When the monitor is installed in the
portrait position
•
Remove the stands (feet).
•
Left edge should be the upper edge from front view.
12. Installing and removing stand
Speaker terminal
How to install stand
1. Please turn monitor off.
2. Place stand onto monitor with the long ends of the feet in
front of the monitor.
3. After inserting stand in guide block, fasten thumbscrews
on both sides of the monitor.
How to remove the stand
1. Spread the protective sheet on the flat surface, such as
a desk.
How to use the attached speaker plug
Standard cable
2. Place monitor on the protective sheet.
Speaker plug
3. Remove thumbscrews with a screwdriver or with your
fingers and place them in a safe place for reuse.
Thumbscrews
Insert the negative (-) side of a standard speaker cable into the
negative (-) side of the speaker plug. The negative side of a
standard speaker cable has a stripe running the length of the cable.
Insert remaining wire into the positive (+) side of the speaker plug.
Hold down on the small lever on the speaker plug to insert cable.
Stand
CAUTION: Handle with care when mounting the display
Fixed cable and speaker plug.
stand and avoid pinching your fingers.
NOTE: Place stand onto monitor so that the long end of
the feet are in the front.
13. When using external speakers
We recommend to using the option speakers designed for
the MultiSync LCD4010 / MultiSync LCD4610.
The external speaker terminals of the MultiSync LCD4010 /
MultiSync LCD4610 may be connectable with the speaker
plug of a mainframe sound speaker.
It this case, please exchange the lead connector of a
mainframe sound speaker for an attached speaker plug.
Insert the fixed cable and speaker plug to the speaker terminal.
English-10
How to Mount and Attach Options to the LCD Monitor
You can attach mounting accessories to the LCD monitor in
one of the following two ways:
3. Ventilation Requirements for enclosure
mounting
To allow heat to disperse, leave space between surrounding
objects as shown in the diagram below.
1. In the upright position
4.To avoid falling down
Fasten the LCD monitor to wall using a cord or chain, which
is sufficient to support the weight of the LCD monitor
(approx. LCD4010: 27,5kg / LCD4610: 35,7kg).
250mm
2. Lay the screen face down
Screw Holes
Protective Sheet
Cord or Chain
Clamper
Screw
Before moving the LCD monitor, the cord or chain should be
removed.
Tabletop Stand
Table
Lay the protective sheet on a table, which was wrapped
around the monitor when it was packaged, beneath the
screen surface so as not to scratch the screen face.
5. To prevent the main power switch from
being changed
To prevent the ability to use the main power switch, please
attach the main switch, which is enclosed as an accessory.
This device cannot be used or installed without the Tabletop
Stand or other mounting accessory. Failure to follow correct
mounting procedures could result in damage to the
equipment or injury to the user or installer. Product warranty
does not cover damage caused by improper installation.
Failure to follow these recommendations could result in
voiding your warranty.
NOTE: With the main power switch cover in place, the main
power switch cannot be turned off. Remove main
power switch cover in order to switch off the display.
When using with other mounting accessory, it must be a
VESA-compatible mounting method and the screws must be
M6 of size and 10mm or longer of length under consideration
of the thickness of the mounting method. (Recommended
torque: 470 - 635N•cm). NEC recommends using mounting
interface that comply with TÜV-GS and/or UL1678 standard
in North America.
Screw
Main switch cover
English-11
Connections
Before making connections:
*
First turn off the power of all the attached equipment and make connections.
*
Refer to the user manual included with each separate piece of equipment.
Wiring Diagram
Personal computer
LCD monitor
DVD player
Personal computer
VCR
Equipment with
digital interface
LCD monitor (second monitor)
Attaching the Ferrite Core
Mounting Position of Ferrite Core
Attach the Ferrite Core to PC Audio Cable.
Use of the cable without mounting the ferrite core will result in the
occurrence of noise.
For PC Audio Cable
Open the ferrite core and clamp it
on the PC Audio cable.
Close the ferrite core.
Attach the two Ferrite Cores to the both ends of PC Audio Cable.
1
2
Ferrite Core
Ferrite Core
Ferrite Core
To AUDIO 1 of monitor
To connector of PC
Band
Band
English-12
Connecting a Personal Computer
Connecting your computer to your LCD monitor will enable you to display your computer’s screen image.
Some video cards may not display an image correctly.
Scanning frequency
Remarks
Resolution
Horizontal
31.5kHz
37.9kHz
48.4kHz
48kHz
Vertical
60Hz
60Hz
60Hz
60Hz
60Hz
60Hz
60Hz
640 x 480
800 x 600
1024 x 768
1280 x 768
1360 x 768
1280 x 1024
1600 x 1200
48kHz
Recommended resolution
Compressed image
64kHz
75kHz
Compressed image
Connect the LCD Monitor to a Personal Computer
•
•
To connect the RGB 2 IN connector (mini D-sub 15 pin) on the LCD monitor, use the supplied PC - Video RGB signal
cable (mini D-sub 15 pin to mini D-sub 15 pin).
To connect the RGB 3 connector (BNC) on the LCD monitor, use a signal cable which is available separately
(mini D-sub 15 pin to BNC x 5). Select RGB 3 from the INPUT button.
•
•
When connecting one or more LCD monitors, use the RGB OUT connector (BNC).
The AUDIO IN 1, 2 and 3 can be used for audio input. For connection, select AUDIO 1, 2 or 3 from the AUDIO INPUT button.
LCD monitor
To audio output
To analog RGB output
Mini D-sub 15 pin
PC or IBM compatible
BNC x 5
BNC x 5
To RGB 3
DVD/HD IN
BNC x 5
LCD monitor (second monitor)
English-13
Connecting to a Macintosh Computer
Connecting your Macintosh computer to your LCD monitor will enable you to display your computer’s screen image. Some
video cards or drivers may not display images correctly.
Connect the LCD Monitor to Macintosh
•
•
•
To connect the RGB 2 IN connector (mini D-sub 15 pin) on the LCD monitor, use the supplied PC - Video RGB signal
cable (mini D-sub 15 pin to mini D-sub 15 pin).
To connect the RGB 3 IN connector (BNC) on the LCD monitor, use the signal cable available separately (mini D-sub
15 pin to BNC x 5).
If you use with a Macintosh PowerBook, set “Mirroring” to Off.
Refer to your Macintosh’s owner’s manual for more information about your computer’s video output requirements and any
special identification or configuring your monitor’s image and monitor may require.
•
The AUDIO IN 1, 2 and 3 can be used for audio input. For connection, select AUDIO 1, 2 or 3 from the AUDIO INPUT button.
LCD monitor
To audio output
To analog RGB output
Mini D-sub 15 pin
Macintosh
BNC x 5
BNC x 5
To RGB 3
DVD/HD IN
BNC x 5
LCD monitor (second monitor)
English-14
Connecting with Digital Interface Equipment
Connections can be made with equipment that is equipped with a digital interface compliant with the DVI (Digital Visual
Interface) standard.
Connect the LCD Monitor to a Computer with a Digital Output
•
•
•
•
•
The RGB 1 IN connector also accepts a DVI-D cable.
Input TMDS signals conforming to DVI standards.
To maintain display quality, use a cable with a quality prescribed by DVI standards.
The AUDIO IN 1, 2 and 3 can be used for audio input. For connection, select AUDIO 1, 2 or 3 from the AUDIO INPUT button.
Mode selection, see “DVI MODE” of page 25.
LCD monitor
To audio output
Equipment with a
digital interface such
as a personal
computer with RGB
output (TMDS)
To DVI output
DVI-D connector
DVI-D connector
English-15
Connecting a DVD Player with component out
Connecting your DVD player to your LCD monitor will enable you to display DVD video.
Refer to your DVD player user’s manual for more information.
Connect the LCD Monitor to a DVD Player
•
To connect the DVD/HD IN connector (BNC) on the LCD monitor, use a separately available BNC connector cable.You will
need a BNC-to-RCA adapter to connect a DVD player with an RCA pin jack to the BNC connector cable (not provided).
Some DVD players may have different connectors such as DVI-D connector.
Select [DVI/HD] mode from the “DVI MODE” menu when you connect a DVI-D connector. Mode selection, see “DVI MODE”
of page 25.
The AUDIO IN 2 and 3 (both RCA) can be used for audio input. For connection, select [AUDIO 2] or [AUDIO 3] from the
AUDIO INPUT button.
LCD monitor
To DVI output To DVD Component video output
DVI-D connector
English-16
Connecting to a Stereo Amplifier
You can connect your stereo amplifier to your LCD monitor. Refer to your amplifier owner’s manual for more information.
Connect the LCD Monitor to a Stereo Amplifier
•
•
•
•
•
Turn on the LCD monitor and the amplifier only after all connections have been made.
Use an RCA cable to connect the AUDIO OUT connector (RCA) on the LCD monitor and the audio input on the amplifier.
Do not reverse the audio left and right jacks.
The AUDIO IN is used for audio input.
The AUDIO OUT jack outputs sound from the selected Audio input.
LCD monitor
To audio right output
To audio left output
VCR or Laser disc player
RCA
Amplifier
RCA
To audio right output
To audio left output
External speaker
External speaker
English-17
Basic Operation
Power ON and OFF Modes
The LCD monitor power indicator will turn green while powered on, or red when in off mode. The monitor can be powered on
or off using the following three options:
1. Pressing the power button.
Note: Before pressing the power button, be sure to turn
on the Main Power Switch on the LCD monitor.
Power Button
2. Using the remote control.
Note: Before operating the remote control, be sure to turn
on the Main Power Switch on the LCD monitor.
3. Pressing the Main Power Switch.
Note: When the Main Power Switch is used to power off
the LCD, the remote control and the power button
will not activate the on mode and both green and
red power indicator turn off. Be sure to turn the
Main Power Switch to the on mode before using
these two options.
Main Power Switch
English-18
NORMAL: Display by the inputed signal aspect ratio by PC
signal, or display in 4:3 aspect ratio at DVD/HD or VIDEO signal.
FULL: Display in entire screen.
WIDE: Expand 16:9 letter box signal to entire screen.
ZOOM (DYNAMIC): Expand 4:3 pictures to the entire screen
with non-linearity. (Some around image will be cut by expansion.)
Power Indicator
Status
Power ON
Green
Power OFF
Red
Power Standby when
“SCHEDULE” is enable
Power Standby
Red On
Green Blinking
Red, Green
ZOOM
Image can be expanded beyond the active display area. The
image which is outside of active diaplay area is not displayed.
Diagnosis (Detecting failure) Red Blinking
ZOOM
* See troubleshooting on page 33
Using Power Management
ZOOM
The LCD monitor follows the VESA approved DPM Power
Management function.
The power management function is an energy saving
function that automatically reduces the power consumption
of the display when the keyboard or the mouse has not been
used for a fixed period.
Picture Mode
RGB 1, 2, 3
HIGHBRIGHT
STANDARD
STANDARD
sRGB
DVD/HD, VIDEO HIGHBRIGHT
CINEMA
The power management feature on your new display has
been set to the “ON” mode. This allows your display to enter
a Power Saving Mode when no signal is applied. This could
potentially increase the life and decrease the power
consumption of the display.
Information OSM
RGB1, 2, 3
Selecting a video source
RGB2
Video Input mode
1024 x 768
48kHz 60Hz
AUDIO : 1
SIZE : FULL
Input signal Information
)
Audio input mode
Picture Size mode
To view a video source:
Use the input button to set [VIDEO].
Use the COLOR SYSTEM menu to set [AUTO], [NTSC],
[PAL], [SECAM], [PAL60], [4.43NTSC], according to your
video format.
DVD/HD
Picture Size
DVD/HD
AUDIO : 3
SIZE : WIDE
Video Input mode
Audio input mode
Picture Size mode
RGB 1, 2, 3
FULL
ZOOM
WIDE
NORMAL
ZOOM
DVD/HD, VIDEO FULL
NORMAL
Signal Type
NORMAL SIZE
Recommended Size
NORMAL
VIDEO
VIDEO<S>
NTSC
Video Input mode
Input Signal Colour System mode
Audio input mode
Picture Size mode
AUDIO : 3
SIZE : NORMAL
4:3
ZOOM
(DYNAMIC)
PIP or POP
Main:RGB2
FULL
Sub:VIDEO<S>
Squeeze
RGB2
1024 x 768
48kHz 60Hz
AUDIO : 1
VIDEO<S>
NTSC
Main picture Information
WIDE
Letter box
Sub picture Information
Main picture Information
)
SIZE : FULL
English-19
OSM (On-Screen-Manager) Controls
Press MENU button to
open Main menu.
Press UP or DOWN button
to select sub-menu.
Press SET button to
decide.
Press UP or DOWN, and PLUS or
MINUS button to select function, or
control which you like.
Press MENU or EXIT
button to exit.
Press SET button to decide.
Remote Control
Press UP or DOWN
button to select.
Press INPUT button
to decide.
Press UP or DOWN, and PLUS or
MINUS button to select function, or
control which you like.
Press EXIT button
to exit.
Press INPUT button to decide.
Control Panel
UP or DOWN button
INPUT button
PICTURE
PICTURE
MAIN MENU
BRIGHTNESS
BRIGHTNESS
BRIGHTNESS
PICTURE
CONTRAST
CONTRAST
SCREEN
SHARPNESS
SHARPNESS
AUDIO
BLACK LEVEL
COLOR CONTROL
COLOR TEMPERATURE
PICTURE RESET
32
BLACK LEVEL
COLOR CONTROL
COLOR TEMPERATURE
PICTURE RESET
OSM screen
PIP
CONFIGURATION 1
CONFIGURATION 2
ADVANCED OPTION
EXIT
MENU
:EXIT MENU
+ -:ADJ
:RETURN
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
SET
EXIT
MENU
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
:RETURN
:EXIT MENU
:SEL
:NEXT
Main-Menu
MAIN MENU
PICTURE
SCREEN
AUDIO
PIP
CONFIGURATION 1
CONFIGURATION 2
ADVANCED OPTION
PICTURE
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
Sub-Menu
PICTURE
Adjusts the overall image and background screen
brightness.
BRIGHTNESS
CONTRAST
SHARPNESS
BLACK LEVEL
COLOR CONTROL
COLOR TEMPERATURE
PICTURE RESET
BRIGHTNESS
32
BRIGHTNESS
CONTRAST
EXIT
MENU
:EXIT MENU
+ -:ADJ
:RETURN
Press + button to increase brightness.
Press - button to decrease brightness.
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
Adjusts the image brightness in relation to the input
signal.
Press + button to increase contrast.
Press - button to decrease contrast.
NOTE: sRGB picture mode is standard and cannot be
changed.
PICTURE
BRIGHTNESS
CONTRAST
CONTRAST
SHARPNESS
BLACK LEVEL
32
COLOR CONTROL
COLOR TEMPERATURE
PICTURE RESET
EXIT
EXIT
EXIT
MENU
:EXIT MENU
+ -:ADJ
:RETURN
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
This function is digitally capable to keep crisp image at
any timing. It is adjustable to get a distinct image or a
soft one as you prefer and set independently for each
picture mode.
Press + button to increase sharpness.
Press - button to decrease sharpness.
PICTURE
BRIGHTNESS
CONTRAST
SHARPNESS
SHARPNESS
BLACK LEVEL
32
COLOR CONTROL
SHARPNESS
COLOR TEMPERATURE
PICTURE RESET
MENU
+ -:ADJ
:RETURN
:EXIT MENU
SET
EXIT
MENU
:SEL
:NEXT
:RETURN
:EXIT MENU
Adjusts the image brightness in relation to the
background.
Press + button to increase black level.
Press - button to decrease black level.
NOTE: sRGB picture mode is standard and cannot be
changed.
PICTURE
BRIGHTNESS
CONTRAST
BLACK LEVEL
SHARPNESS
BLACK LEVEL
32
COLOR CONTROL
BLACK LEVEL
COLOR TEMPERATURE
PICTURE RESET
MENU
+ -:ADJ
:RETURN
:EXIT MENU
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
PICTURE
Adjusts the noise reduction level.
BRIGHTNESS
CONTRAST
SHARPNESS
TINT
NOISE REDUCTION
32
COLOR
NOISE REDUCTION
Press + button to increase reduction level.
Press - button to decrease reduction level.
BLACK LEVEL
NOISE REDUCTION
EXIT
MENU
:EXIT MENU
+ -:ADJ
:RETURN
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
*:INPUT VIDEO only
English-20
Adjust the tint of the screen.
PICTURE
BRIGHTNESS
CONTRAST
SHARPNESS
TINT
COLOR
BLACK LEVEL
NOISE REDUCTION
TINT
32
TINT
Press + button to Skin colour becomes greenish.
Press - button to Skin colour becomes purplish.
EXIT
MENU
:EXIT MENU
+ -:ADJ
:RETURN
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
*:INPUT DVD/HD, VIDEO only
PICTURE
Adjust the colour depth of the screen.
BRIGHTNESS
CONTRAST
SHARPNESS
TINT
COLOR
32
COLOR
Press + button to increase colour depth.
Press - button to decrease colour depth.
COLOR
BLACK LEVEL
NOISE REDUCTION
EXIT
MENU
:EXIT MENU
+ -:ADJ
:RETURN
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
*:INPUT DVD/HD, VIDEO only
R, Y, G, C, B, M, S: Increases or decreases Red, Yellow,
Green, Cyan, Blue, Magenta and Saturation depending
upon which is selected. The change in colour will appear
on screen and the direction (increase or decrease) will be
shown by the colour bars.
PICTURE
COLOR CONTROL
R
Y
G
C
B
M
S
0
0
0
0
0
0
0
BRIGHTNESS
CONTRAST
SHARPNESS
BLACK LEVEL
COLOR CONTROL
COLOR CONTROL
COLOR TEMPERATURE
PICTURE RESET
EXIT
MENU
MENU
MENU
:SEL + -:ADJ
:RETURN
:EXIT MENU
SET
EXIT
MENU
:SEL
:NEXT
:RETURN
:EXIT MENU
*:INPUT RGB1,2,3 only
NOTE: sRGB picture mode is standard and cannot be
changed.
To adjust the colour temperature of entire screen.
Adjusting lower colour temperature makes the screen
reddish and higher colour temperature makes the screen
bluish.
NOTE: sRGB picture mode is standard and cannot be
changed.
PICTURE
BRIGHTNESS
CONTRAST
COLOR TEMPERATURE
SHARPNESS
COLOR
TEMPERATURE
BLACK LEVEL
9600K
COLOR CONTROL
COLOR TEMPERATURE
PICTURE RESET
EXIT
+ -:ADJ
:RETURN
:EXIT MENU
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
Selecting Picture reset allows you to reset all OSM
settings about PICTURE setting.
Select “Yes” and press “SET” button to restore to factory
preset data.
PICTURE
BRIGHTNESS
CONTRAST
PICTURE RESET
SHARPNESS
NO
BLACK LEVEL
COLOR CONTROL
PICTURE RESET
COLOR TEMPERATURE
PICTURE RESET
YES
EXIT
:SEL
:RETURN
:EXIT MENU
Press “EXIT” button to cancel and then return to the
previous menu.
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
Main-Menu
MAIN MENU
PICTURE
SCREEN
AUDIO
PIP
CONFIGURATION 1
CONFIGURATION 2
ADVANCED OPTION
SCREEN
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
Sub-Menu
Controls Horizontal Image position within the display
area of the LCD.
SCREEN
H POSITION
V POSITION
CLOCK
H POSITION
0
CLOCK PHASE
H RESOLUTION
V RESOLUTION
ZOOM MODE
H POSITION
V POSITION
EXIT
MENU
+ -:ADJ
:RETURN
:EXIT MENU
Press + button to move screen to right.
Press - button to move screen to left.
SCREEN RESET
SET
EXIT
MENU
:SEL
:NEXT
:RETURN
:EXIT MENU
Controls Vertical Image position within the display
area of the LCD.
SCREEN
H POSITION
V POSITION
CLOCK
V POSITION
0
CLOCK PHASE
H RESOLUTION
V RESOLUTION
ZOOM MODE
EXIT
MENU
Press + button to move screen to UP.
+ -:ADJ
:RETURN
:EXIT MENU
SCREEN RESET
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
Press - button to move screen to DOWN.
Press + button to expand the width of the image on
the screen to the right.
Press - button to narrow the width of the image on the
screen to the left.
SCREEN
H POSITION
V POSITION
CLOCK
CLOCK
1782
CLOCK PHASE
H RESOLUTION
V RESOLUTION
ZOOM MODE
CLOCK
EXIT
MENU
:EXIT MENU
+ -:ADJ
:RETURN
SCREEN RESET
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
*:INPUT RGB2/3 only
SCREEN
H POSITION
V POSITION
CLOCK
CLOCK PHASE
18
CLOCK PHASE
H RESOLUTION
V RESOLUTION
ZOOM MODE
CLOCK PHASE
To change the snow noise of the image.
EXIT
MENU
:EXIT MENU
+ -:ADJ
:RETURN
SCREEN RESET
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
*:INPUT RGB2/3 only
Adjusts the horizontal size by increasing or decreasing
the setting.
Press + button to expand the width of the image on
the screen.
Press - button to narrow the width of the image on
the screen.
SCREEN
H POSITION
V POSITION
CLOCK
H RESOLUTION
1360
CLOCK PHASE
H RESOLUTION
V RESOLUTION
ZOOM MODE
H RESOLUTION
EXIT
MENU
:EXIT MENU
+ -:ADJ
:RETURN
SCREEN RESET
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
*:INPUT RGB1/2/3 only
English-21
Adjusts the vertical size by increasing or decreasing the
setting.
Press + button to expand the height of the image on the
screen.
Press - button to narrow the height of the image on
the screen.
SCREEN
H POSITION
V RESOLUTION
V POSITION
CLOCK
768
CLOCK PHASE
H RESOLUTION
V RESOLUTION
ZOOM MODE
SCREEN RESET
V RESOLUTION
EXIT
MENU
:EXIT MENU
+ -:ADJ
:RETURN
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
*:INPUT RGB1/2/3 only
Selects the screen zoom mode. Zoom mode will be
selected when you select the “ZOOM” by pushing the
“SIZE” button on remote controller.
When you select the “CUSTOM”, you will be able to
adjust optional horizontal and vertical size.
SCREEN
ZOOM MODE
CUSTOM
OFF
H POSITION
V POSITION
CLOCK
CLOCK PHASE
H RESOLUTION
V RESOLUTION
ZOOM MODE
SCREEN RESET
SET
EXIT
MENU
SET
EXIT
:RETURN MENU :EXIT MENU
:SEL
:NEXT
:RETURN
:EXIT MENU
:SEL
:NEXT
*:INPUT RGB1/2/3 only
You can also select 16:9, 14:9 and DYNAMIC.
(INPUT DVD/HD,VIDEO only)
ZOOM MODE
CUSTOMV
16:9
14:9
DYNAMIC
OFF
Press “SET” button to show a control menu as follows:
Increase or decrease “ZOOM” slider to adjust the whole
size and then adjust horizontal and vertical size by
H ZOOM and V ZOOM. Increase or decrease “H POS”
and “V POS” to adjust the picture position.
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
ZOOM MODE
*:INPUT DVD/HD, VIDEO only
CUSTOM
ZOOM
X 1.00
X 1.00
X 1.00
0%
Selecting “DYNAMIC” will expand 4:3 pictures to the
entire screen with non-linearity. (Some around image
will be cut by expansion.) Dynamic image is the same
as FULL size image when HDTV 1080i or 720p signal
is input.
H ZOOM
V ZOOM
H POS
V POS
0%
EXIT
MENU
:EXIT MENU
:SEL + - :ADJ
:RETURN
Selecting “OFF" image will be displayed 1 by 1 pixel.
(If you input over 1366x768 resolution signal, it will be
displayed as shrank image.)
Selecting Screen reset allows you to reset all OSM
settings from SCREEN setting.
Select “Yes” and press “SET” button to restore the
factory preset data.
SCREEN
H POSITION
SCREEN RESET
V POSITION
CLOCK
NO
CLOCK PHASE
H RESOLUTION
V RESOLUTION
ZOOM MODE
SCREEN RESET
SCREEN RESET
YES
EXIT
MENU
:EXIT MENU
:SEL
:RETURN
Press “EXIT” button to cancel and then return to the
previous menu.
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
Main-Menu
MAIN MENU
PICTURE
SCREEN
AUDIO
PIP
CONFIGURATION 1
CONFIGURATION 2
ADVANCED OPTION
AUDIO
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
Sub-Menu
Adjust the balance of L/R volume.
Press + button to move the stereo sound image to right.
Sound of the left side will be small.
AUDIO
BALANCE
L
BALANCE
TREBLE
BASS
R
CENTER
AUDIO RESET
BALANCE
Press - button to move the stereo sound image to left.
EXIT
MENU
+ -:ADJ
:RETURN
:EXIT MENU
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
AUDIO
To accentuate or reduce the high frequency sound.
TREBLE
BALANCE
TREBLE
BASS
0
AUDIO RESET
Press + button to increase TREBLE sound.
Press - button to decrease TREBLE sound.
TREBLE
BASS
EXIT
MENU
:EXIT MENU
+ -:ADJ
:RETURN
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
AUDIO
To accentuate or reduce the low frequency sound.
BASS
BALANCE
TREBLE
BASS
0
AUDIO RESET
Press + button to increase BASS sound.
Press - button to decrease BASS sound.
EXIT
MENU
:EXIT MENU
+ -:ADJ
:RETURN
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
Selecting Audio reset allows you to reset all OSM
settings from AUDIO setting.
Select “Yes” and press “SET” button to restore the
factory preset.
AUDIO
BALANCE
TREBLE
AUDIO RESET
BASS
NO
AUDIO RESET
AUDIO RESET
YES
EXIT
MENU
:SEL
:RETURN
:EXIT MENU
Press “EXIT” button to cancel and then return to the
previous menu.
SET
EXIT
MENU
:SEL
:NEXT
:RETURN
:EXIT MENU
English-22
Main-Menu
MAIN MENU
PICTURE
SCREEN
AUDIO
PIP
CONFIGURATION 1
CONFIGURATION 2
ADVANCED OPTION
PICTURE IN PICTURE
Sub-Menu
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
Selecting the size of picture inserted at the
“Picture-in-Picture” (PIP) mode.
PIP
PIP SIZE
PIP AUDIO
PIP RESET
PIP SIZE
LARGE
MIDDLE
SMALL
PIP SIZE
EXIT
MENU
:EXIT MENU
:SEL
:RETURN
“Large”, “Middle” and “Small” are available.
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
Selecting the sound source in PIP mode.
When selecting “MAIN AUDIO”, you will get the sound
for the main picture and when selecting “PIP AUDIO”,
you will get the sound for the picture instead.
When side-by-side mode, MAIN AUDIO is the sound
source of the left side screen and PIP AUDIO is the
right side.
PIP
PIP SIZE
PIP AUDIO
PIP RESET
PIP AUDIO
MAIN AUDIO
/
PIP AUDIO
MENU
:EXIT MENU
PIP AUDIO
EXIT
+ -:SEL
:RETURN
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
Selecting PIP Reset allows you to reset all OSM
settings from PIP setting.
Select “Yes” and press “SET” button to restore the factory
preset data.
PIP
PIP SIZE
PIP AUDIO
PIP RESET
PIP RESET
NO
PIP RESET
YES
EXIT
MENU
:EXIT MENU
:SEL
:RETURN
Press “EXIT” button to cancel and then return to the
previous menu.
SET
EXIT
MENU
:SEL
:NEXT
:RETURN
:EXIT MENU
Main-Menu
MAIN MENU
PICTURE
SCREEN
AUDIO
PIP
CONFIGURATION 1
CONFIGURATION 2
ADVANCED OPTION
CONFIGURATION 1
Sub-Menu
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
Press “SET” button to automatically adjust screen size,
horizontal position, vertical position, clock, clock phase,
white level and black level.
Press “EXIT” button to cancel execution AUTO SETUP
and then will return to the previous menu.
CONFIGURATION 1
AUTO SETUP
AUTO ADJUST
AUTO BRIGHTNESS
POWER SAVE
LANGUAGE
AUTO SETUP
PRESS
SET
TO RESET
MENU
AUTO SETUP
SCREEN SAVER
SIDE BORDER COLOR
SET
EXIT
:CANCEL
:EXIT MENU
:RESET
SET
EXIT
MENU
:SEL
:NEXT
:RETURN
:EXIT MENU
*:INPUT RGB2/3 only
CONFIGURATION 1
AUTO SETUP
AUTO ADJUST
AUTO BRIGHTNESS
POWER SAVE
LANGUAGE
Selecting the auto adjust ON/OFF.
AUTO ADJUST
ON
Selecting ON when changing the timing, the horizontal
position, vertical position and clock-phase will adjust
automatically.
/
OFF
MENU
AUTO ADJUST
SCREEN SAVER
SIDE BORDER COLOR
+ -:SEL
EXIT
:RETURN
:EXIT MENU
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
*:INPUT RGB2/3 only
CONFIGURATION 1
AUTO SETUP
AUTO BRIGHTNESS
ON
AUTO BRIGHTNESS
Selecting the auto brightness ON/OFF.
When select “ON”, the brightness will be automatically
adjusted.
AUTO ADJUST
AUTO BRIGHTNESS
POWER SAVE
LANGUAGE
SCREEN SAVER
SIDE BORDER COLOR
/
OFF
MENU
*:INPUT RGB1/2/3 only
EXIT
+ -:SEL
:RETURN
:EXIT MENU
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
Selecting RGB “ON”, the monitor will go to power
management mode when RGB1,2,3 sync is lost.
Selecting VIDEO “ON”, the monitor will go to power
management mode after about 10 minutes delay from
when DVD/HD and VIDEO input signal is lost.
CONFIGURATION 1
AUTO SETUP
AUTO ADJUST
AUTO BRIGHTNESS
POWER SAVE
LANGUAGE
POWER SAVE
RGB
ON
ON
/
/
OFF
OFF
POWER SAVE
LANGUAGE
VIDEO
SCREEN SAVER
SIDE BORDER COLOR
+ -:ADJ
EXIT
:RETURN
MENU
:EXIT MENU
:SEL
SET
EXIT
MENU
:SEL
:NEXT
:RETURN
:EXIT MENU
CONFIGURATION 1
AUTO SETUP
AUTO ADJUST
AUTO BRIGHTNESS
POWER SAVE
LANGUAGE
LANGUAGE
ENGLISH
DEUTSCH
FRANCAIS
ESPAÑOL
ITALIANO
SVENSKA
SCREEN SAVER
SIDE BORDER COLOR
OSM control menus are available in seven languages.
SET
EXIT
MENU
EXIT
:SEL
:NEXT
:RETURN
:EXIT MENU
English-23
Select “SCREEN SAVER” functions to reduce the risk of
the “image persistence”.
GAMMA: The display gamma is changed and fixed when
selected “ON”.
COOLING FAN: The built in cooling fan is always on
when set “ON”.
BRIGHTNESS: The brightness is decreased when
selected “ON”.
CONFIGURATION 1
AUTO SETUP
AUTO ADJUST
AUTO BRIGHTNESS
POWER SAVE
LANGUAGE
SCREEN SAVER
SIDE BORDER COLOR
SCREEN SAVER
GAMMA
ON
ON
ON
/
/
/
OFF
COOLING FAN
BRIGHTNESS
MOTION
AUTO
OFF
MOTION: Image is slightly expanded and moves
4 directions (UP, DOWN, RIGHT, LEFT) periodically
(Need setting the time for movement).
Movement area is approximately +/- 10mm from original
position; Please locate the important information such as
text within 90% area of screen image.
See note (1) for this functions.
SCREEN SAVER
10 SEC.
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
MENU
EXIT
:SEL + -:ADJ
:RETURN
:EXIT MENU
PIP, POP, Side by Side and STILL will be disabled when
“MOTION” is active.
Selecting the Colour System depends on your input
video format.
AUTO: NTSC, PAL, SECAM, PAL60 or 4.43 NTSC is
automatically selected.
NTSC: Specific selection of NTSC.
PAL: Specific selection of PAL.
CONFIGURATION 1
COLOR SYSTEM
POWER SAVE
LANGUAGE
SCREEN SAVER
COLOR SYSTEM
SIDE BORDER COLOR
CONFIGURATION RESET
FACTORY RESET
AUTODEUTSCH
NTSC
PAL
SECAM
4.43 NTSC
PAL-60
COLOR SYSTEM
SET
EXIT
MENU
:EXIT MENU
:SEL
EXIT :RETURN MENU :EXIT MENU
:SEL
:NEXT
:RETURN
*:INPUT VIDEO only
SECAM: Specific selection of SECAM.
PAL-60: Specific selection of PAL60.
4.43NTSC: Specific selection of 4.43 NTSC.
Adjustment the side black bar color white when 4:3
image displayed, black to white.
Press + button, the bar will become whiter.
Press - button, the bar will become darker.
CONFIGURATION 1
AUTO BRIGHTNESS
POWER SAVE
LANGUAGE
POWER SAVE
COLOR SYSTEM
SIDE BORDER COLOR
CONFIGURATION RESET
FACTORY RESET
SIDE BORDER COLOR
SIDE BORDER
COLOR
50
EXIT
MENU
:EXIT MENU
+ -:ADJ
:RETURN
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
Selecting the CONFIGURATION RESET allows you to
reset all configuration settings.
Select “Yes” and press “SET” button to restore the factory
preset data.
CONFIGURATION 1
POWER SAVE
LANGUAGE
SCREEN SAVER
COLOR SYSTEM
SIDE BORDER COLOR
CONFIGURATION RESET
FACTORY RESET
CONFIGURATION RESET
CONFIGURATION
RESET
NO
YES
EXIT
MENU
:EXIT MENU
:SEL
:RETURN
Press “EXIT” button to cancel and return the previous
menu.
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
Selecting “YES” allows you to reset PICTURE, SCREEN,
AUDIO, CONFIGURATION1,2 and ADVANCED OPTION
will be back to factory settings (except LANGUAGE,
DATE & TIME and SCHEDULE).
Select “YES” and press “SET” button to restore the
factory preset data.
CONFIGURATION 1
POWER SAVE
LANGUAGE
SCREEN SAVER
COLOR SYSTEM
SIDE BORDER COLOR
CONFIGURATION RESET
FACTORY RESET
FACTORY RESET
NO
FACTORY RESET
YES
EXIT
MENU
:EXIT MENU
:SEL
:RETURN
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
Press “EXIT” button to cancel and return the previous
menu.
Main-Menu
MAIN MENU
PICTURE
SCREEN
AUDIO
PIP
CONFIGURATION 1
CONFIGURATION 2
ADVANCED OPTION
CONFIGURATION 2
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
Sub-Menu
CONFIGURATION 2
A set up ON/OFF of long cable alteration can be
performed. In ON, enforcement of an AUTO Set Up
performed alteration.
LONG CABLE ON/OFF
LONG CABLE MANUAL
OSM TURN OFF
LONG CABLE ON/OFF
LONG CABLE
ON/OFF
*:INPUT RGB2/3 only
INFORMATION OSM
OFF TIMER
ON
/
OFF
OSM POSITION
INPUT DETECT
EXIT
MENU
:EXIT MENU
+ -:SEL
:RETURN
MONITOR INFORMATION
SET
EXIT
MENU
:SEL
:NEXT
:RETURN :EXIT MENU
Please refer to the CD-ROM included for alteration.
English-24
To compensate for image degradation, which is caused by
using a long cable.
RED/GREEN/BLUE DELAY
To adjust the each phase of RED, GREEN and BLUE
signal.
LEVEL: 0 - 6
RED/GREEN/BLUE SHARPNESS
To adjust the each performance degradation of RED,
GREEN and BLUE signal.
CONFIGURATION 2
LONG CABLE MANUAL
LONG CABLE ON/OFF
LONG CABLE MANUAL
OSM TURN OFF
RED DELY
0
2
0
0
0
0
0
0
/
LEVEL: 0 - 45
GREEN DELAY
BLUE DELAY
LONG CABLE
MANUAL
*:INPUT RGB2/3 only
RED SHARPNESS
GREEN SHARPNESS
BLUE SHARPNESS
SOG PEAK
INFORMATION OSM
OFF TIMER
SOG PEAK
To adjust the shape of Sync on Green signal.
Level: 0 - 1
OSM POSITION
INPUT DETECT
VIDEO EQ.
MONITOR INFORMATION
SYNC TERMINATE
HI
LO
SET
EXIT
MENU
:SEL
:NEXT
:RETURN
:EXIT MENU
:SEL + -:ADJ
EXIT :RETURN MENU :EXIT MENU
VIDEO EQ (Input RGB 3 only)
To optimize the shape (Tailing) of RED, GREEN and
BLUE signal.
Level: 0 - 7
SYNC TERMINATE (Input RGB 3 only)
To select the terminate resistance for matching the cable
impedance.
HI: 2.2K ohm/LO:75 ohm
The OSM control menu will stay on as long as it is use.
In the OSM Turn Off submenu, you can select how long
the monitor waits after the last touch of a button to shut
off the OSM control menu. The preset choices are
10 -240 seconds.
CONFIGURATION 2
LONG CABLE ON/OFF
LONG CABLE MANUAL
OSM TURN OFF
OSM TURN OFF
INFORMATION OSM
OFF TIMER
10 SEC.
OSM TURN OFF
OSM POSITION
INPUT DETECT
EXIT
MENU
:EXIT MENU
+ -:ADJ
:RETURN
MONITOR INFORMATION
SET
EXIT
MENU
:SEL
:NEXT
:RETURN :EXIT MENU
Selects the information OSM display or not. The
information OSM will display when input signal or
source change or warning message like as no-signal or
out-of range.
CONFIGURATION 2
LONG CABLE ON/OFF
LONG CABLE MANUAL
OSM TURN OFF
INFORMATION OSM
ON
10 SEC.
INFORMATION OSM
OFF TIMER
OFF
INFORMATION OSM
OSM POSITION
INPUT DETECT
EXIT
MENU
:EXIT MENU
:SEL + -:ADJ
:RETURN
MONITOR INFORMATION
SET
EXIT
MENU
:SEL
:NEXT
:RETURN :EXIT MENU
A time between 3 to 10 seconds is available.
To select OFF TIMER mode ON/OFF.
In the OFF TIMER menu, you can preset the monitor to
automatically power down.
A time between 1 to 24 hours is available.
When the OFF TIMER is set, the SCHEDULE
(see page 28) settings will be disabled.
CONFIGURATION 2
LONG CABLE ON/OFF
LONG CABLE MANUAL
OSM TURN OFF
OFF TIMER
ON
1
HOUR
:RETURN
INFORMATION OSM
OFF TIMER
OFF
OFF TIMER
OSM POSITION
INPUT DETECT
EXIT
MENU
:EXIT MENU
:SEL + -:ADJ
MONITOR INFORMATION
SET
EXIT
MENU
:SEL
:NEXT
:RETURN
:EXIT MENU
Selects the kind of DVI-D equipment which is connected
RGB1.
Select “DVI-PC” when PC or other computer equipment
is connected.
CONFIGURATION 2
OSM TURN OFF
DVI MODE
INFORMATION OSM
OFF TIMER
DVI-PC
+ -:SEL
/
DVI-HD
DVI MODE
DVI MODE
OSM POSITION
INPUT DETECT
MONITOR INFORMATION
EXIT
MENU
:EXIT MENU
:RETURN
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
Select “DVI-HD” when DVD player, which has DVI-D
output, is connected.
*:INPUT RGB1 only
Adjusts the position of the OSM menu.
Press + button to move right side of the screen.
Press - button to move left side of the screen.
CONFIGURATION 2
OSM POSITION
LEFT
UP
LONG CABLE ON/OFF
LONG CABLE MANUAL
OSM TURN OFF
INFORMATION OSM
OFF TIMER
RIGHT
OSM POSITION
OSM POSITION
INPUT DETECT
Press
Press
button to move right side of the screen.
button to move left side of the screen.
MONITOR INFORMATION
DOWN
SET
EXIT
MENU
EXIT
MENU
:EXIT MENU
:SEL
:NEXT
:RETURN
:EXIT MENU
+ - :ADJ
:RETURN
English-25
Selects the method of input detection when more than
two computers are connected.
FIRST DETECT: When the current video input signal is
not present, then the monitor searches for a video signal
from the other video input port. If the video signal is
present in the other port, then the monitor switches the
video source input port to the new found video source
automatically. The monitor will not look for other video
signals while the current video source is present.
This function is available at input RGB 1/2/3.
LAST DETECT: When the monitor is displaying a signal
from the current source and a new secondary source is
supplied to the monitor, the monitor will automatically
switch to the new video source. When current video input
signal is not present, the monitor searches for a video
signal from the other video input port. If the video signal
is present in the other port, then the monitor switches the
video source input port to the new found video source
automatically.
CONFIGURATION 2
LONG CABLE ON/OFF
LONG CABLE MANUAL
OSM TURN OFF
INPUT DETECT
FIRST DETECT
INFORMATION OSM
OFF TIMER
LAST DETECT
VIDEO DETECT
NONE
INPUT DETECT
OSM POSITION
INPUT DETECT
EXIT
MENU
:EXIT MENU
:SEL
:RETURN
MONITOR INFORMATION
SET
EXIT
MENU
:SEL
:NEXT
:RETURN
:EXIT MENU
This function is available at input RGB 1/2/3.
VIDEO DETECT: DVD/HD or VIDEO inputs will have
priority over RGB1/2/3. When DVD/HD or VIDEO input
signal is present the monitor will change and keep to the
DVD/DH or VIDEO input.
NONE: The Monitor will not search the other video input
port.
CONFIGURATION 2
LONG CABLE ON/OFF
LONG CABLE MANUAL
OSM TURN OFF
MONITOR INFORMATION
MODEL NAME:
LCD4010
MONITOR
INFORMATION
INFORMATION OSM
OFF TIMER
SERIAL:
Indicates the model and serial number of your monitor.
OSM POSITION
12315XXX
INPUT DETECT
EXIT
MENU
:EXIT MENU
:RETURN
MONITOR INFORMATION
SET
EXIT
MENU
:SEL
:NEXT
:RETURN :EXIT MENU
Main-Menu
MAIN MENU
PICTURE
SCREEN
AUDIO
PIP
CONFIGURATION 1
CONFIGURATION 2
ADVANCED OPTION
ADVANCED OPTION
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
Sub-Menu
Selects the S-Video input port function.
PRIORITY:
If cable is connected to the S-Video input, it will have
priority the composite input port.
SEPARATE:
ADVANCED OPTION
S-VIDEO MODE
BLACK LEVEL EXPANSION
GAMMA SELECTION
IMAGE FLIP
SCAN MODE
SCAN CONVERSION
FILM MODE
S-VIDEO MODE
PRIORITY
/
SEPARATE
MENU
S-VIDEO MODE
EXIT
+ -:SEL
:RETURN
:EXIT MENU
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
S-Video port and Composite port are selectable as
independent input port.
Selects to decision of input signal about below timings,
1024x768, 1280x768 and 1360x768.
AUTO: Determines the resolution automatically.
1024x768: Determines the resolution as 1024x768
1280x768: Determines the resolution as 1280x768
1360x768: Determines the resolution as 1360x768
ADVANCED OPTION
S-VIDEO MODE
INPUT RESOLUTION
AUTO
INPUT RESOLUTION
GAMMA SELECTION
IMAGE FLIP
1024 X 768
1280 X 768
1360 X 768
MONITOR ID
INPUT RESOLUTION
TILE MATRIX
HEAT PROTECT
SET
EXIT
MENU
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
:RETURN
:EXIT MENU
:SEL
*:INPUT RGB2/3 only
ADVANCED OPTION
S-VIDEO MODE
BLACK LEVEL EXPANSION
BLACK LEVEL EXPANSION
GAMMA SELECTION
IMAGE FLIP
Selects a level of black expansion.
In case of go under the black cut-off level, please adjust
the “Black level” in moderation on OSM menu.
BLACK LEVEL
EXPANSION
*:INPUT VIDEO only
HIGH
/
MIDDLE
/
OFF
SCAN MODE
SCAN CONVERSION
FILM MODE
+ -:SEL
EXIT
MENU
:RETURN :EXIT MENU
SET
MENU
:EXIT MENU
:SEL
:NEXT EXIT :RETURN
Selects a display gamma.
2.2
ADVANCED OPTION
S-VIDEO MODE
GAMMA SELECTION
BLACK LEVEL EXPANSION
GAMMA SELECTION
IMAGE FLIP
2.4
S gamma
Native
2.
2.
S
2
4
GAMMA
NATIVE
GAMMA SELECTION
SCAN MODE
SCAN CONVERSION
FILM MODE
:SEL
EXIT
:RETURN
MENU
:
E
X
I
T
M
E
N
U
SET
EXIT
MENU
:SEL
:NEXT
:RETURN
:EXIT MENU
NOTE: sRGB picture mode is standard and cannot be
changed.
English-26
Selects the image flipping or rotation.
NORMAL: Normal display.
H MIRROR: Mirror image for horizontal direction.
V MIRROR: Mirror image for vertical direction.
ROTATE: Rotate the image 180 degrees.
ADVANCED OPTION
S-VIDEO MODE
BLACK LEVEL EXPANSION
GAMMA SELECTION
IMAGE FLIP
SCAN MODE
SCAN CONVERSION
FILM MODE
IMAGE FLIP
NORMAL
H MIRROR
V MIRROR
ROTATE
IMAGE FLIP
SET
EXIT
MENU
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
:RETURN
:EXIT MENU
:SEL
ADVANCED OPTION
S-VIDEO MODE
BLACK LEVEL EXPANSION
GAMMA SELECTION
IMAGE FLIP
SCAN MODE
SCAN CONVERSION
FILM MODE
Changes the display area of the image.
SCAN MODE
OVERSCAN
/
UNDERSCAN
OVERSCAN: Set to display area about 95%
UNDERSCAN: Set to display area about 100%
SCAN MODE
+ -: SEL
EXIT
MENU
:RETURN :EXIT MENU
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
*:INPUT DVD/HD, VIDEO only
Selects IP (Interlace to Progressive) converter function.
PROGRESSIVE: Enable the IP function, to convert
interlace signal to progressive. Normally use this setting.
INTERLACE: Disable the IP function.
ADVANCED OPTION
S-VIDEO MODE
BLACK LEVEL EXPANSION
GAMMA SELECTION
IMAGE FLIP
SCAN MODE
SCAN CONVERSION
FILM MODE
SCAN CONVERSION
PROGRESSIVE
/
INTERLACE
SCAN CONVERSION
+ -: SEL
EXIT
MENU
:RETURN
:EXIT MENU
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
NOTE: This mode is better suited for motional pictures,
but it is in danger of image retention.
Selects Film mode function.
AUTO: Enable the Film mode function. This mode is
better suited for movies, which is converted 24 Frames/
sec source to DVD Video. We recommend to select
“PROGRESSIVE” in “SCAN CONVERSION”.
OFF: Disable the Film mode function. This mode is
better suited for Broadcasting or VCR source.
ADVANCED OPTION
S-VIDEO MODE
BLACK LEVEL EXPANSION
GAMMA SELECTION
IMAGE FLIP
SCAN MODE
SCAN CONVERSION
FILM MODE
FILM MODE
AUTO
/
OFF
FILM MODE
+ -: SEL
EXIT
MENU
:RETURN :EXIT MENU
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
*:INPUT DVD/HD, VIDEO only
Set the Monitor ID number to control the daisy chained
multiple MultiSync LCD4010s / MultiSync LCD4610s
with RS-232C.
ADVANCED OPTION
MONITOR ID
ID No.
MONITOR ID
IR CONTROL
TILE MATRIX
HEAT STATUS
1
MONITOR ID
POWER ON DELAY
DATE & TIME
SCHEDULE
+ -: SEL
EXIT
MENU
:RETURN :EXIT MENU
ADVANCED OPTION RESET
The Monitor ID number is selectable between 1 and 26.
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
Selects the infrared wireless remote controller mode
with using the RS-232C daisy chain.
The item in this menu will become effective by pressing
“SET” button on the selected item.
NORMAL: The monitor will be controlled normally by
wireless remote controller.
PRIMARY: Set “PRIMARY” at the head of the daisy
chained monitors by RS-232C.
SECONDARY: Set “SECONDARY” after 2nd daisy
chained monitor.
IR CONTROL
ADVANCED OPTION
NORMAL
PRIMARY
SECONDARY
LOCK
MONITOR ID
IR CONTROL
TILE MATRIX
HEAT STATUS
IR CONTROL
POWER ON DELAY
DATE & TIME
SCHEDULE
ADVANCED OPTION RESET
SET
EXIT
MENU
SET
EXIT
MENU
:EXIT MENU
:SEL
:SET
:RETURN
:EXIT MENU
:SEL
:NEXT
:RETURN
LOCK: Disable the monitor control by infrared wireless
remote controller.
Keep pressing “DISPLAY” button during 5 sec or more,
this setting will return to “NORMAL”.
Tile Matrix demonstrates multiple screens. This feature
provides a single large screen using up to 25 monitors.
It will be able to divide up to 5 each H and V.
This requires you to feed the PC output into each of the
monitors through a distributor.
Do not use LCD4010 and LCD4610 together for
TILE MATRIX.
ADVANCED OPTION
TILE MATRIX
H
V
MONITORS
MONITORS
1
1
1
YES
YES
MONITOR ID
IR CONTROL
TILE MATRIX
HEAT STATUS
H MONITORS: Select number of horizontal divide.
V MONITORS: Select number of vertical divide.
POSITION: Select a position to expand the screen.
TILE COMP: Works in tandem with Tile Matrix to
compensate for the width of the tile bezels in order to
accurately display the image.
POSITION
TILE COMP
ENABLE
/
/
NO
NO
TILE MATRIX
POWER ON DELAY
DATE & TIME
SCHEDULE
ADVANCED OPTION RESET
EXIT
:SEL
:RETURN
SET
EXIT
MENU
MENU
:SEL
:NEXT
:RETURN
:EXIT MENU
+ -: ADJ
:EXIT MENU
ENABLE: Select “YES”, the monitor will expand the
selected position.
PIP, POP, SIDE by SIDE and STILL and “DYNAMIC”
ZOOM mode will be disabled when “TILE MATRIX” is
activated.
English-27
Information of status for COOLING FAN, BRIGHTNESS
and TEMPERATURE.
COOLING FAN comes to run when inside temperature
is over a guaranteed limit.
BRIGHTNESS comes to be decreased when inside
temperature is over guaranteed limit with cooling fun.
In this case warning is displayed on the screen.
HEAT STATUS
ADVANCED OPTION
STATUS
MONITOR ID
COOLING FAN1
COOLING FAN2
BRIGHTNESS
ON
IR CONTROL
ON
TILE MATRIX
NORMAL
HEAT STATUS
POWER ON DELAY
DATE & TIME
HEAT STATUS
TEMPERATURE
SENSOR 1
SENSOR 1
0.0
0.0
C
C
/
/
32.0
32.0
F
F
SCHEDULE
ADVANCED OPTION RESET
SET
EXIT
MENU
EXIT
MENU
:EXIT MENU
:SEL
:NEXT
:RETURN
:EXIT MENU
:RETURN
Adjusts the delay time from “standby” to “power on”
mode.
ADVANCED OPTION
POWER ON DELAY
MONITOR ID
IR CONTROL
TILE MATRIX
HEAT STATUS
3 SEC.
POWER ON DELAY
DATE & TIME
POWER ON DELAY
DATE & TIME
SCHEDULE
+ -: ADJ
EXIT MENU
:RETURN :EXIT MENU
ADVANCED OPTION RESET
“POWER ON DELAY” time is selectable between 0 and
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
50 sec.
DATE & TIME
ADVANCED OPTION
YEAR
MONTH
DAY
2004
JANUARY
MONITOR ID
IR CONTROL
TILE MATRIX
HEAT STATUS
01
TIME
Adjusts the current date and time for internal clock.
You should set this function when you use “SCHEDULE”.
00
:
00
/
POWER ON DELAY
DATE & TIME
DAYLIGHT SAVING YES
NO
SCHEDULE
CURRENT DATE
JAN. 01. 2004 00
TIME
00 00
ADVANCED OPTION RESET
:
:
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
SET
EXIT
MENU
:RETURN :EXIT MENU
+ -: ADJ
:SET
Programs the monitor’s working
schedule.
Schedule the power on and
power off with hour and a day of
the week. Also sets the input port.
This OSM can’t remove except
EXIT.
ADVANCED OPTION
MONITOR ID
IR CONTROL
TILE MATRIX
HEAT STATUS
SCHEDULE
POWER ON DELAY
DATE & TIME
SCHEDULE
ADVANCED OPTION RESET
SET
MENU
:EXIT MENU
:SEL
:NEXT EXIT :RETURN
(see “NOTE 3” on page 29 for
EXIT
further information)
Selecting ADVANCED OPTION reset allows you to reset
all OSM settings from ADVANCED OPTION settings,
except for DATE & TIME, and SCHEDULE.
Select “YES” and press “SET” button to restore the
factory preset data.
ADVANCED OPTION
ADVANCED OPTION RESET
MONITOR ID
IR CONTROL
TILE MATRIX
ADVANCED
OPTION RESET
NO
HEAT STATUS
POWER ON DELAY
DATE & TIME
YES
SCHEDULE
EXIT
MENU
:EXIT MENU
ADVANCED OPTION RESET
:SEL
:RETURN
SET
EXIT
MENU
:RETURN :EXIT MENU
:SEL
:NEXT
Press “EXIT” button to cancel and then return the
previous menu.
NOTE 1: IMAGE PERSISTENCE
Please be aware that LCD Technology may experience a phenomena known as Image Persistence. Image Persistence occurs when a
residual or “ghost” image of a previous image remains visible on the screen. Unlike CRT monitors, LCD monitors’ image persistence is not
permanent, but constant images being displayed for a long period of time should be avoided.
To alleviate image persistence, turn off the monitor for as long as the previous image was displayed. For example, if an image was on the
monitor for one hour and a residual image remains, the monitor should be turned off for one hour to erase the image.
As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and using a moving screen saver
at regular intervals whenever the screen is idle or turning off the monitor when not in use.
Please set “SCREEN SAVER”, “DATE &TIME” and “SCHEDULE” functions to further reduce the risk of Image persistence.
For long life use of Public Display
< Image Sticking of LCD Panel >
When LCD panel is operated continuously for long hours, a trace of electric charge remains near the electrode inside LCD, and residual or
"ghost" image of previous image may be observed. (Image Persistence)
Image Persistence is not permanent, but when fixed image is displayed for long period, ionic impurities inside LCD are accumulated along
the displayed image, and it is observed permanently. (Image Sticking)
< Recommendations >
For preventing the fast transition to Image Sticking, and for longer life usage of LCD, following are recommended.
1. Fixed image should not be displayed for long period, and changed to another images with short cycle.
2. When no use, please turn off the monitor by remote control, or use Power Management Function of monitor or use Schedule Function of
monitor.
English-28
3. Reducing the environmental temperature is effective for long life use.
When Protection board (glass, acryl) is installed over the LCD surface, enclosed into the box / wall, or stack the monitor, please utilize the
temperature sensors inside monitor.
To reduce the environmental temperature, the monitor should be set Low Brightness or Cooling Fan "ON" by using Screen sever Function.
4. Please use "Screen Saver Mode" of monitor.
NOTE 2: MONITOR ID and IR CONTROL
Using the one PC or one infra-red wireless controller, you can control up to 26 MultiSync LCD4010 / MultiSync LCD4610 that are
connected by daisy chained RS-232C.
1. Connect a PC and MultiSync LCD4010 / MultiSync LCD4610.
Connect a PC’s RS-232C control output to the MultiSync LCD4010’s / MultiSync LCD4610’s RS-232C input.
You can connect other MultiSync LCD4010 / MultiSync LCD4610; Connect MultiSync LCD4010’s / MultiSync LCD4610’s RS-232C output
to other MultiSync LCD4010’s / MultiSync LCD4610’s RS-232C input. (Refer to page 30).
2. Set Monitor ID.
Set “MONITOR ID” in the “ADVANCED OPTION” menu.
“MONITOR ID” should be set to a unique number on all daisy chained MultiSync LCD4010 / MultiSync LCD4610 from 1 to 26.
We recommend numbering continuously from 1 in a sequential number.
Set “PRIMARY” to “IR CONTROL” in the “ADVANCED OPTION” menu on the first of the daisy chained monitors.
Set “SECONDERY” to “IR CONTROL” on other monitors.
3. Press “DISPLAY” button aiming at the “PRIMARY” monitor then ID select OSM will be shown at top left side of the screen.
ID: 1 <- ID number itself.
ID No.: 1 <- ID number of the controllable monitor.
ID: 1
ID No: 2
Monitor ID
"Monitor ID" which
you want to control
Press “+” button to increase this “ID No.”.
Press “-” button to decrease it.
If you control all the daisy-chained monitors at the same time,
please select “ID No.” “ALL”.
4. Operate wireless remote controller with aiming at the “PRIMARY” monitor.
The “MENU OSD” will appear on the selected ID No.’s monitor.
NOTE: If “ID No.” select OSM is showing at the “PRIMARY” monitor, press “DISPLAY” button to clear this OSM.
HINT:
If you lost control by a reason of wrong setting “IR CONTROL”, keep pressing during 5 sec or more the “DISPLAY” button.
The monitor will reset “IR CONTROL” to “NORMAL”.
NOTE 3: HOW TO SETUP SCHEDULE
Using the “SCHEDULE” function allows you to set up to seven different scheduled time intervals when the LCD Monitor will be activated.
You can select the time the monitor turns on and turns off, the day of week the monitor is activated, and which input source the monitor will
use for each scheduled activation period. A check mark in the box next to the number of the schedule indicates that the selected schedule
is in effect.
To select which schedule to set, use the up/down arrows to move the red bar vertically under the number (1 to 7) of the schedule.
Use the (+) and (-) buttons to move the red bar horizontally within the particular schedule. The “SET” button is used to make a selection.
If you create a schedule but do not want to use a power on time, select “--” in the “ON” time slot.
If you do not want to use a power off time select “--” in the OFF time slot.
If there is no input selected (“--” showing in the input spot) the input from the previous schedule will be used.
The selection of EVERY DAY within a schedule takes priority over other schedules that are set up to operate weekly.
When schedules are overlapping, scheduled Power ON time has priority over scheduled Power OFF time.
If there are two schedules programmed for the same time, then the highest numbered schedule has priority.
When the “OFF TIMER” (see page 25) is set, the “SCHEDULE” function is disabled.
English-29
Controlling the LCD monitor via RS-232C Remote Control
This LCD monitor can be controlled by connecting a personal computer with a RS-232C terminal.
Functions that can be controlled by a personal computer are:
•
•
Power ON or OFF
Switching between input signals
Connection
LCD Monitor + PC
to RS-232C
from RS-232C
to RS-232C
from RS-232C
“IN” terminal
“OUT” terminal
“IN” terminal
“OUT” terminal
PC
RS-232C Cable
RS-232C Cable
Next MultiSync LCD4010 /
MultiSync LCD4610 RS-232C
“IN” terminal
NOTE: If your PC (IBM or IBM compatible) is equipped only with a 25-pin serial port connector, a 25-pin serial port adapter
is required. Contact your dealer for details.
* RS-232C OUT terminal can connect MultiSync LCD4010 / MultiSync LCD4610 only. Do not connect other equipment.
The following control sequence is used for a single MultiSync LCD4010 / MultiSync LCD4610. To control multiple MultiSync
LCD4010 / MultiSync LCD4610 monitors that are daisy-chained together please use the extended control command. Instructions for
the extended control command can be found on the CD included with the display. The file is called “External_control_LCD4X10.pdf”.
When using the following control commands, all of the daisy-chained monitors can be controlled at the same time from one monitor.
Reply and status commands, however, will only pertain to the primary monitor, not secondary monitors.
1) Interface
PROTOCOL
BAUD RATE
DATA LENGTH
PARITY BIT
STOP BIT
RS-232C
9600 [bps]
8 [bits]
NONE
1 [bits]
FLOW CONTROL NONE
This LCD monitor uses RXD, TXD and GND lines for RS-232C control.
2) Control command diagram
The command is structured by the address code, function code, data code and end code. The length of the command is
different for each function.
Address code
30h 30h
'0' '0'
Function code
Function
Data code
Data
End code
0Dh
HEX
ASCII
Function
Data
[Address code]
[Function code]
[Data code]
30h 30h (ASCII code, '0' '0'), fixed.
A code of each fixed control move.
A code of each fixed control data (number) and not always indicated.
0Dh (In ASCII code, ' ') fixed.
[End code]
English-30
3) Control sequence
(1) The command from a computer to the LCD monitor will be sent in 400ms.
(2) The LCD monitor will send a return command 400ms* after it has received and encoded. If the command isn’t
received correctly, the LCD monitor will not send the return command.
(3) The personal computer checks the command and confirms if the command, which has been sent, has been executed or not.
(4) This LCD monitor sends various codes other than return code. When having a control sequence by RS-232C, reject other
codes from personal computers side.
*: The sending time of return command may delay depending on the condition (during changing of the input signal, etc.).
Example: Turn the power ON ( ’ ’ is for ASCII code)
Sending commands
from the PC
Status code from
LCD monitor
Meaning
30 30 21 0D
Command for
POWER ON
’0’ ’0’ ’!’ ’
’
30 30 21 0D
Command received
(Command echoed back)
’0’ ’0’ ’!’ ’
’
4) Operation commands
The operation commands execute the basic operation setting of this LCD monitor.
It may not operate when changing the signal:
Operation
ASCII
!
HEX
POWER ON
POWER OFF
INPUT RGB 1
INPUT RGB 2
INPUT RGB 3
INPUT VIDEO
INPUT DVD/HD
21h
"
22h
_r1
_r2
_r3
_v1
_v2
5Fh 72h 31h
5Fh 72h 32h
5Fh 72h 33h
5Fh 76h 31h
5Fh 76h 32h
5Fh 76h 33h
INPUT S-VIDEO* _v3
•
•
POWER OFF command should be operated over 1 minute after the power is turned on.
POWER ON command should be operated over 1 minute after the power is turned off.
* S-VIDEO is SEPARATE only
5) Read command
Host computer sends the command without Data-code to monitor.
After receiving this command, the monitor returns the command with Data-code of current status to host computer.
< ex. > When Host computer ask Power status of monitor, the status of monitor is powered-on.
Command from computer
Command from Monitor
Detail of command
30 30 76 50 0D 0''0'v''P'[enter]
Ask about the power status of monitor.
30 30 76 50 31 0D '0''0''v''P''1'[enter] Monitor is powered-on.
Structure of the Read-command
ASCII
HEX
Data (Receive)
Function
Data (Receive)
Function
76 50
ON
vP
vP
vI
1
31
POWER
OFF(stand by)
RGB-1(DVI-D)
RGB-2(D-SUB)
0
76 50
30
r1
r2
r3
v1
v2
v3
p1
p2
76 49
72 31
72 32
72 33
76 31
76 32
76 33
70 31
70 32
2B 20 32 35
2E 30
2B 20 32 35
vI
76 49
Input
RGB-3(BNC)
vI
76 49
Video
vI
76 49
DVD/HD
S-VIDEO
vI
76 49
vI
76 49
HIGHBRIGHT
Picture mode
vM
vM
76 4D
76 4D
74 63 78 31
STANDARD
resolution
Around
tcx1
(ex.) +25.0
(ex.) +25
Temperature
of Internal
monitor
0.5˚C
AV board
resolution
1˚C
74 63 31
tc1
resolution
0.5˚C
74 63 78 32
74 63 32
2B 20 33 30 2E 35
2B 20 33 31
Around
Inverter
PCB
(ex.) +30.5
(ex.) +31
tcx2
tc2
resolution
1˚C
NOTE: For complete information please see file “External_Control_LCD4X10.pdf” on the CD-ROM.
English-31
Features
Reduced Footprint: Provides the ideal solution for environments requiring superior image quality but with size and weight
limitations. The monitor’s small footprint and low weight allow it to be moved or transported easily from one location to another.
Colour Control Systems: Allows you to adjust the colours on your screen and customize the colour accuracy of your monitor
to a variety of standards.
OmniColor: Combines Six-axis colour control and the sRGB standard. Six-axis colour control permits colour adjustments via
six axes (R, G, B, C, M and Y) rather than through the three axes (R, G and B) previously available. The sRGB standard
provides the monitor with a uniform colour profile. This assures that the colours displayed on the monitor are exactly the same
as on the colour printout (with sRGB supporting operating system and sRGB printer). This allows you to adjust the colours on
your screen and customise the colour accuracy of your monitor to a variety of standards.
sRGB Colour Control: A new optimized colour management standard which allows for colour matching on computer displays
and other peripherals. The sRGB standard, which is based on a calibrated colour space, allows for optimal colour
representation and backward compatibility with other common colour standards.
OSM (On-Screen Manager) Controls: Allow you to quickly and easily adjust all elements of your screen image via simple to
use on-screen menus.
Plug and Play: The Microsoft® solution with the Windows® 95/98/Me/2000/XP operating system facilitates setup and
installation by allowing the monitor to send its capabilities (such as screen size and resolutions supported) directly to your
computer, automatically optimizing display performance.
IPM (Intelligent Power Manager) System: Provides innovative power-saving methods that allow the monitor to shift to a
lower power consumption level when on but not in use, saving two-thirds of your monitor energy costs, reducing emissions
and lowering the air conditioning costs of the workplace.
Multiple Frequency Technology: Automatically adjusts monitor to the display card’s scanning frequency, thus displaying the
resolution required.
FullScan Capability: Allows you to use the entire screen area in most resolutions, significantly expanding image size.
VESA Standard Mounting Interface: Allows users to connect their LCD monitor to any VESA standard third party mounting
arm or bracket. Allows for the monitor to be mounted on a wall or an arm using any third party compliant device. NEC
recommends using mounting interface that comply with TÜV-GS and/or UL1678 standard in North America.
DVI-D: The digital-only subset of DVI ratified by the Digital Display Working Group (DDWG) for digital connections between
computers and displays. As a digital-only connector, analog support is not provided off a DVI-D connector. As a DVI-based
digital only connection, only a simple adapter is necessary for compatibility between DVI-D and other DVI-based digital
connectors such as DFP and P&D.
TILE MATRIX, TILE COMP: Demonstrates multiple screens with an accurate image and compensates for the bezel width.
ZOOM: Expands the image individually for horizontal and vertical direction.
RS-232C daisy chain: You can control the multiple monitors by controller or wireless remote controller.
Self-diagnosis: When an internal error should occur, a failure state will be indicated.
CableComp: Automatic long cable compensation prevents image quality degradation (colour shift and dull signals) caused by
long cable lengths.
English-32
Troubleshooting
No picture
•
•
•
•
The signal cable should be completely connected to the display card/computer.
The display card should be completely seated in its slot.
Front Power Switch and computer power switch should be in the ON position.
Check to make sure that a supported mode has been selected on the display card or system being used.
(Please consult display card or system manual to change graphics mode.)
•
•
Check the monitor and your display card with respect to compatibility and recommended settings.
Check the signal cable connector for bent or pushed-in pins.
Power Button does not respond
Unplug the power cord of the monitor from the AC outlet to turn off and reset the monitor.
•
Image persistence
•
Please be aware that LCD Technology may experience a phenomenon known as Image Persistence. Image Persistence
occurs when a residual or “ghost” image of a previous image remains visible on the screen. Unlike CRT monitors, LCD
monitors’ image persistence is not permanent, but constant images being displayed for a long period of time should be
avoided. To alleviate image persistence, turn off the monitor for as long as the previous image was displayed. For example,
if an image was on the monitor for one hour and a residual image remains, the monitor should be turned off for one hour to
erase the image.
NOTE: As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and using a
moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use.
Image is unstable, unfocused or swimming is apparent
•
Signal cable should be completely attached to the computer.
•
Use the OSM Image Adjust controls to focus and adjust display by increasing or decreasing the fine adjustment.
When the display mode is changed, the OSM Image Adjust settings may need to be re-adjusted.
•
•
Check the monitor and your display card with respect to compatibility and recommended signal timings.
If your text is garbled, change the video mode to non-interlace and use 60Hz refresh rate.
Image of component signal is greenish
Check to see if the DVD/HD input connector is selected.
•
LED on monitor is not lit (no green or red colour can be seen)
•
Power Switch should be in the ON position and power cord should be connected.
•
Make certain the computer is not in a power-saving mode (touch the keyboard or mouse).
RED LED on monitor is blinking
A certain failure might have occurred, please contact your nearest authorized NEC DISPLAY SOLUTIONS service facility.
•
Display image is not sized properly
•
Use the OSM Image Adjust controls to increase or decrease the coarse adjustment.
•
Check to make sure that a supported mode has been selected on the display card or system being used.
(Please consult display card or system manual to change graphics mode.)
Selected resolution is not displayed properly
•
Use OSM Display Mode to enter Information menu and confirm that the appropriate resolution has been selected.
If not, select corresponding option.
No Sound
•
•
•
Check to see if speaker cable is properly connected.
Check to see if mute is activated.
Check to see if volume is set at minimum.
Remote Control is not available
•
•
•
•
Check the Remote Control’s batteries status.
Check if batteries are inserted correctly.
Check if the Remote Control is pointing at the monitor’s remote sensor.
The remote control system may not function when direct sunlight or strong illumination strikes the remote control sensor of
the LCD monitor, or when there is an object in the path.
“SCHEDULE”/“OFF TIMER” function is not working properly
•
The “SCHEDULE” function will be disabled when the “OFF TIMER” is set.
•
If the “OFF TIMER” function is enable and the power to the LCD monitor is turned off if the power supply is interrupted
unexpectedly, then the “OFF TIMER” will be reset.
Either light vertical or horizontal stripes may appear, depending on the specific display pattern. This is no product fault or
degradation.
English-33
Specifications for MultiSync LCD4010
Product Specifications
Analog Input
Digital Input
LCD Module
40" / 101.6cm diagonal
Pixel Pitch: 0.648mm
Resolution: 1366 x 768 dots
Colour: Over 16 million colours (depending on video card used)
Brightness: 450cd/m2 (Typ.)
Contrast Ratio: 1000:1
Viewing Angle: Up 85°/ Down 85°/ Left 85°/ Right 85° (typ) @ CR>10
Design View Distance: 1100mm
Frequency
Horizontal: 15.625/15.734kHz, 31.5kHz - 91.1kHz
31.5kHz - 91.1kHz
50.0/58.0 - 85.0 Hz
Vertical: 50.0/58.0 - 85.0 Hz
25.0MHz - 162.0MHz
Pixel Clock
25.0MHz - 162.0MHz
Viewable Size
885.168 x 497.64mm
Input Signal
PC-Input:
Video: Analog RGB 0.7V p-p
Input Impedance 75 ohm
TMDS
Composite sync on Green Video: 0.3Vp-p Neg. (video 0.7Vp-p Pos.)
Sync: Separate: TTL level (Pos./Neg.)
Input Impedance 2.2K ohm (RGB3: 2.2k ohm/75 ohm selectable)
Input-terminal: BNC (R,G,B,H,V) 15pin Mini D-sub
DVI-D (Digital)
Composite 1.0V p-p Input Impedance 75 ohm BNC and RCA-INPUT
Y/C Y:0.7V p-p C:0.283V p-p Input Impedance 75 ohm S-TERMINAL-INPUT
Component 1.0/0.7V p-p Input Impedance 75 ohm BNC-INPUT
RCA PIN-JACK L/R INPUT, STEREO Mini Jack INPUT
In: 9 Pin Mini D-sub
VIDEO Input:
AUDIO Input:
RS-232C:
Out: 9 Pin Mini D-sub (with daisy chain)
Output Signal
PC-Output:
Video: Analog RGB Video: 0.7V p-p with 75 ohm terminated
(RGB3 only)
Sync: Separate HV sync: TTL level (Posi / Nega) with 2.2k ohm terminated
Output-terminal: BNC (R,G,B,H,V)
VIDEO Output:
AUDIO Output:
Speaker Output:
BNC 1 Output, Composite 1.0V p-p with 75 ohm terminated
RCA PIN-JACK L/R: 1 Output, 0.15Vrms with 1k ohm terminated
External Speaker Jack 7W + 7W (8 ohm)
Resolutions Supported
640 x 480 at 60Hz to 85Hz
800 x 600 at 50Hz, 60Hz to 85Hz
1024 x 768 at 50Hz, 60Hz to 85Hz
1280 x 768 at 50Hz, 60Hz to 85Hz
1360 x 768 at 50Hz, 60Hz* to 85Hz
1280 x 1024 at 60Hz to 85Hz
1600 x 1200 at 60Hz.................................................. Maximum Resolution
* Recommended Resolution
NTSC/PAL/SECAM/4.43NTSC/PAL60
Component: 480i, 480p, 720p, 1080i
Power Supply
2.3 - 0.95A @ 100-240VAC, 50/60Hz
Operational
Environment
Temperature: 5 - 40°C
Humidity: 20 - 80% (without condensation)
Storage
Temperature: -20 - 60°C
Environment
Humidity: 10 - 90% (without condensation)/ 90% - 3.5% x (Temp - 40°C) regarding over 40°C
Dimension
Net: 981.8 (W) x 579.8 (H) x 140 (D) mm (without Stand)
981.8 (W) x 611.1 (H) x 330 (D) mm (with Stand)
Gross: 1147 (W) x 761 (H) x 312 (D) mm
Weight
Net: 63.9 lbs/29.0 kg
Gross: 80.5 lbs/36.5 kg
VESA compatible arm
mounting interface
3 x 200mm x 200mm (8 Holes)
2 x 200 mm x 200 mm (6 Holes)
Complied Regulatory and
Guidelines
UL60950-1/CSA C22.2 No.60950-1/ TUV-GS/EN60950-1
FCC-B/DOC-B/EN55022-A/EN55024/EN61000-3-2/EN61000-3-3/CE/GOST-R/PSB/C-tick-A
Power Management
Plug & Play
VESA DPM
VESA DDC2B, DDC/CI
Accessories
User’s manual, Power Cord, Video Signal Cable, Remote Control, AA Battery x 2,
Clamper x 3, Screw x 4, CD-ROM, Ferrite Core x 2, Stand for the Independence x 2,
Curled head Screw for stand x 2, Band x 2, Speaker plug x 1set, Main power switch cover
NOTE: Technical specifications are subject to change without notice.
English-34
Specifications for MultiSync LCD4610
Product Specifications
Analog Input
Digital Input
LCD Module
46" / 116.8cm diagonal
Pixel Pitch: 0.7455mm
Resolution: 1366 x 768 dots
Colour: Over 16 million colours (depending on video card used)
Brightness: 500cd/m2 (Typ.)
Contrast Ratio: 1000:1
Viewing Angle: Up 89.5°/ Down 89.5°/ Left 89.5°/ Right 89.5° (typ) @ CR>10
Design View Distance: 1300mm
Frequency
Horizontal: 15.625/15.734kHz, 31.5kHz - 91.1kHz
31.5kHz - 91.1kHz
50.0/58.0 - 85.0 Hz
Vertical: 50.0/58.0 - 85.0 Hz
25.0MHz - 162.0MHz
1018.4 x 572.5mm
Pixel Clock
25.0MHz - 162.0MHz
Viewable Size
Input Signal
PC-Input:
Video: Analog RGB 0.7V p-p
Input Impedance 75Ohm
TMDS
Composite sync on Green Video: 0.3Vp-p Neg. (video 0.7Vp-p Pos.)
Sync: Separate: TTL level (Pos./Neg.)
Input Impedance 2.2KOhm (RGB3: 2.2k ohm/75 ohm selectable)
Input-terminal: BNC (R,G,B,H,V) 15pin Mini D-sub
DVI-D (Digital)
Composite 1.0V p-p Input Impedance 75 ohm BNC and RCA-INPUT
Y/C Y:0.7V p-p C:0.283V p-p Input Impedance 75Ohm S-TERMINAL-INPUT
Component 1.0/0.7V p-p Input Impedance 75Ohm BNC-INPUT
RCA PIN-JACK L/R INPUT, STEREO Mini Jack INPUT
In: 9 Pin Mini D-sub
VIDEO Input:
AUDIO Input:
RS-232C:
Out: 9 Pin Mini D-sub (with daisy chain)
Output Signal
PC-Output:
Video: Analog RGB Video: 0.7V p-p with 75 ohm terminated
(RGB3 only)
Sync: Separate HV sync: TTL level (Posi / Nega) with 2.2k ohm terminated
Output-terminal: BNC (R,G,B,H,V)
VIDEO Output:
AUDIO Output:
Speaker Output:
BNC 1 Output, Composite 1.0V p-p with 75 ohm terminated
RCA PIN-JACK L/R: 1 Output, 0.15Vrms with 1k ohm terminated
External Speaker Jack 7W + 7W (8 ohm)
Resolutions Supported
640 x 480 at 60Hz to 85Hz
800 x 600 at 50Hz, 60Hz to 85Hz
1024 x 768 at 50Hz, 60Hz to 85Hz
1280 x 768 at 50Hz, 60Hz to 85Hz
1360 x 768 at 50Hz, 60Hz* to 85Hz
1280 x 1024 at 60Hz to 85Hz
1600 x 1200 at 60Hz.................................................. Maximum Resolution
* Recommended Resolution
NTSC/PAL/SECAM/4.43NTSC/PAL60
Component: 480i, 480p, 720p, 1080i
Power Supply
2.6 - 1.1A @ 100-240VAC, 50/60Hz
Operational
Environment
Temperature: 5 - 40°C
Humidity: 20 - 80% (without condensation)
Storage
Temperature: -20 - 60°C
Environment
Humidity: 10 - 90% (without condensation)/ 90% - 3.5% x (Temp - 40°C) regarding over 40°C
Dimension
Net: 1112.8 (W) x 655.8 (H) x 140 (D) mm (without Stand)
1112.8 (W) x 687.1 (H) x 351 (D) mm (with Stand)
Gross: 1278 (W) x 837 (H) x 312 (D) mm
Weight
Net: 78.7 lbs/35.7 kg
Gross: 95.7 lbs/43.4 kg
VESA compatible arm
mounting interface
3 x 200mm x 200mm (8 Holes)
2 x 200 mm x 200 mm (6 Holes)
Complied Regulatory and
Guidelines
UL60950-1/CSA C22.2 No.60950-1/ TUV-GS/EN60950-1
FCC-B/DOC-B/EN55022-A/EN55024/EN61000-3-2/EN61000-3-3/CE/GOST-R/PCB/C-tick-A
Power Management
Plug & Play
VESA DPM
VESA DDC2B, DDC/CI
Accessories
User’s manual, Power Cord, Video Signal Cable, Remote Control, AA Battery x 2,
Clamper x 3, Screw x 4, CD-ROM, Ferrite Core x 2, Stand for the Independence x 2,
Curled head Screw for stand x 2, Band x 2, Speaker plug x 1set, Main power switch cover
NOTE: Technical specifications are subject to change without notice.
English-35
Pin Assignment
1) Analog RGB input (MiniDsub15p): R G B 2
Pin No
Name
1
2
Video Signal Red
Video Signal Green
Video Signal Blue
GND
3
Mini D-SUB 15P
1
4
5
5
DDC-GND
Red-GND
6
10
15
6
11
7
Green-GND
Blue-GND
+5V (DDC)
SYNC-GND
GND
8
9
10
11
12
13
14
15
DDC-SDA
H-SYNC
V-SYNC
DDC-SCL
2) S-VIDEO input: V I D E O
Pin No
Name
1
2
3
4
GND
GND
Y (Luminance)
C (Chroma)
3) Digital RGB input (DVI-D): R G B 1
Pin - Assignment of DVI connector:
8
1
2
3
4
5
6
7
8
TX2-
9
TX1-
17 TX0-
18 TX0+
1
TX2+
10 TX1+
16
Shield (TX2 / TX4) 11 Shield (TX1 / TX3) 19 Shield (TX0 / TX5)
9
NC
12 NC
20 NC
NC
13 NC
21 NC
DDC-Serial Clock
DDC-Serial Data
NC
14 +5V power
15 Ground
16 Hot plug detect
22 Shield (TXC)
23 TXC+
24 TXC-
24
17
4) RS-232 input
Pin No
Name
NC
Mini D-SUB 9P
1
2
3
4
5
6
7
8
9
5
RXD
TXD
NC
1
6
9
GND
NC
RTS
CTS
NC
English-36
|