NEC MULTISYNC PA271W User Manual

MultiSync PA241W

MultiSync PA271W

User’s Manual

WARNING

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT

USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE

PRONGS CAN BE FULLY INSERTED.

REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED

FROM WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT

THE POWER CORD FROM THE AC OUTLET.DO NOT REMOVE COVER (OR BACK). NO USER

SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol warns user that uninsulated voltage within the unit may have sufﬁcient magnitude to cause

electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit.

This symbol alerts the user that important literature concerning the operation and maintenance of this unit

has been included. Therefore, it should be read carefully in order to avoid any problems.

CAUTION: Please use the power cord provided with this display in accordance with the table below. If a power cord is not

supplied with this equipment, please contact your supplier. For all other cases, please use a power cord that matches the

AC voltage of the power outlet and has been approved by and complies with the safety standard of your particular country.

European

Continental

Plug Type

North America

U.K.

Chinese

Japanese

Plug Shape

Country

Voltage

U.S.A./Canada

120*

EU (except U.K.)

230

U.K.

230

China

220

Japan

100

*When operating the monitor with its AC 125-240V power supply, use a power supply cord that matches the power supply

voltage of the AC power outlet being used.

NOTE:

This product can only be serviced in the country where it was purchased.

Declaration

Declaration of the Manufacturer

We hereby certify that the color monitor MultiSync

PA241W (L249TU)/MultiSync PA271W (L279TV)

and marked with

are in compliance with:

Council Directive 2006/95/EC:

– EN 60950-1

Council Directive 2004/108/EC:

– EN 55022

NEC Display Solutions, Ltd.

4-13-23, Shibaura,

Minato-Ku

Tokyo 108-0023, Japan

– EN 61000-3-2

– EN 61000-3-3

– EN 55024

Council Directive 2009/125/EC:

EC No. 1275/2008

– EN 62301:2005

Windows is a registered trademark of Microsoft Corporation. NEC is a registered trademark of NEC Corporation.

ErgoDesign is a registered trademark of NEC Display Solutions, Ltd. in Austria, Benelux, Denmark, France, Germany, Italy,

Norway, Spain, Sweden, U.K.

All other brands and product names are trademarks or registered trademarks of their respective owners.

Adobe^®is a registered trademark or trademark of Adobe Systems Incorporated in the U.S. and/or other

countries.

DisplayPort is trademarks of Video Electronics Standards Association.

English-1

Canadian Department of Communications

Compliance Statement

DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.2 No. 60950-1.

FCC Information

Use the attached speciﬁed cables with the MultiSync PA241W/MultiSync PA271W color monitor so as not to interfere

with radio and television reception.

(1)

The power supply cord you use must have been approved by and comply with the safety standards of U.S.A.,

and meet the following condition.

Power supply cord

Length

Non shield type, 3-conductor

2.0 m (PA241W), 3.0 m (PA271W)

Plug shape

U.S.A

(2)

Please use the supplied shielded video signal cable, 15-pin mini D-SUB to DVI-A cable or DVI-D to DVI-D cable.

Use of other cables and adapters may cause interference with radio and television reception.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used

in accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult your dealer or an experienced radio/TV technician for help.

If necessary, the user should contact the dealer or an experienced radio/television technician for additional suggestions.

The user may ﬁnd the following booklet, prepared by the Federal Communications Commission, helpful: “How to Identify

and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Ofﬁce,

Washington, D.C., 20402, Stock No. 004-000-00345-4.

Declaration of Conformity

This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not

cause harmful interference, and (2) this device must accept any interference received, including interference that may cause

undesired operation.

U.S. Responsible Party: NEC Display Solutions of America, Inc.

Address:

500 Park Blvd, Suite 1100

Itasca, Illinois 60143

(630) 467-3000

Tel. No.:

Type of Product:

Display Monitor

Equipment Classiﬁcation: Class B Peripheral

Models: MultiSync PA241W (L249TU)

MultiSync PA271W (L279TV)

We hereby declare that the equipment speciﬁed above conforms

to the technical standards as speciﬁed in the FCC Rules.

English-2

Product Features

•

DisplayPort, which supports 10-bit color depth.

5-setting, easy-to-switch picture mode (see page 11).

Accurate color reproduction for high-end graphic design (see page 11).

Quick warmup time.

Picture-in-picture/picture-by-picture dual-screen mode includes real-time preview (see page 21).

USB hub with two upstream ports (see page 12).

MultiProﬁler extends color management feature, including automatic ICC proﬁle updates (ICC proﬁle Emulation, Printer

Emulation) (see page 15).

•

Low power consumption via ECO Mode (see page 10).

Small footprint design.

Contents

Your new NEC monitor box* should contain the following:

•

MultiSync monitor with tilt/swivel/pivot/height adjust stand

Power Cord

Video Signal Cable (DVI-D to DVI-D cable)*¹

Video Signal Cable (Mini D-SUB 15 pin to Mini D-SUB 15 pin) (only for PA241W)

DisplayPort cable

Setup Manual

CD-ROM

Screw (x 4) (to mount the monitor to a ﬂexible arm (page 8))

Mini D-SUB 15 pin to

Mini D-SUB 15 pin

(only for PA241W)

Power Cord

Screws

(Type of power cord included will

depend on the where the LCD

monitor is to be shipped)

CD-ROM

Setup Manual

DVI-D to DVI-D cable*¹

DisplayPort cable

NOTE:

This monitor can be equipped with optional “MultiSync Sound bar”.

Please ask your dealer or check our website http://www.necdisplaysolution.com

Remember to save your original box and packing material to transport or ship the monitor.

Dual link DVI cable for PA271W.

English-3

Quick Start

To connect the LCD monitor to your system, follow these instructions:

1. Turn off the power to your computer.

2. For a PC or MAC with DVI digital output: Connect the DVI signal cable to the connector of the display card in your system

(Figure A.1). Tighten all screws.

For a PC with Analog output (only for PA241W): Connect a 15-pin mini D-SUB to DVI-A signal cable (not included) to the

connector of the display card in your system (Figure A.2).

For a MAC (only for PA241W): Connect a Macintosh cable adapter (not included) to the computer, then attach the 15-pin

mini D-SUB signal cable to the Macintosh cable adapter (Figure A.3).

NOTE:

Some Macintosh systems do not require a Macintosh cable adapter.

For a PC with DisplayPort output: Connect the DisplayPort cable to the connector of the display card in your system

(Figure A.4).

Macintosh Cable

Figure A.2

Adapter

DisplayPort cable

Figure A.3

Figure A.4

Figure A.1

(not included)

NOTE:

1. Please use a DisplayPort cable with a DisplayPort logo.

2. When removing the DisplayPort cable, hold down the top button to release the lock.

3. Height adjustment is locked by lock button. Place hand on top of the monitor to push down the screen to the lowest position.

Slide the lock button to unlock (Figure B.1).

NOTE:

Handle with care when unlocking stand.

Place hands on each side of the monitor to tilt the LCD panel 30-degree angle and lift up to the highest position.

Slide the cable cover up (Figure B.2).

NOTE:

Cable cover is not removable.

30° Tilt

Cable cover

Figure B.1

Figure B.2

English-4

4. Connect all cables to the appropriate connectors (Figure C.1). When using the USB cable, connect the B type connector

to the USB upstream port on the right back side of the monitor and the A type connector to the downstream port on the

computer (Figure C.1a). If using the cord from a USB device, plug into one of the downstream ports of the monitor.

NOTE:

Incorrect cable connections may result in irregular operation, damage display quality/components of LCD module

and/or shorten the module’s life.

30° Tilt

USB downstream

A Type

Highest

B Type

Stand

Position

B Type

USB downstream

USB upstream1

USB upstream2

Figure C.1a

DVI-1

DisplayPort

D-SUB*¹

DVI-2

DC-OUT*

Power cord

* NEC optional product attachment.

Do not use this connector unless speciﬁed.

Figure C.1

5. To keep the cables neatly organized, place them into the cable management system that is built into the stand.

Place the cables in the hooks ﬁrmly and evenly (Figure C.2 and Figure C.3).

6. Please check that you can still rotate, raise and lower the monitor screen when you have installed the cables.

Power Cord

D-SUB Cable*¹

Power Cord

DVI-1 Cable

D-SUB Cable*¹

DVI-1/DVI-2 Cables

DisplayPort Cable

USB Cable

DisplayPort

Cable

Figure C.2

Figure C.3

*1 Only for PA241W.

English-5

7. Slide down the cable cover (Figure D.1).

8. Connect one end of the power cord to the AC inlet on the back of the monitor and the other end to the power outlet.

NOTE:

Please refer to Caution section of this manual for proper selection of AC power cord.

Figure D.1

9. Turn on the monitor with the front power button (Figure E.1) and the computer.

10. Only for PA241W: No-touch auto adjust automatically adjusts the monitor to optimal settings upon initial setup for most

timings. For further adjustments, use the following OSD controls:

• Auto Contrast (Analog input only)

• Auto Adjust (Analog input only)

Refer to the Controls section of this User’s Manual for a full description of these OSD controls.

NOTE:

If you have any problems, please refer to the Troubleshooting section of this User’s Manual.

Power Button

Figure E.1

Raise and Lower Monitor Screen

The monitor may be raised or lowered in either Portrait or Landscape mode.

To raise or lower screen, place hands on each side of the monitor and lift or lower to the desired height (Figure RL.1).

NOTE:

Handle with care when raising or lowering the monitor screen.

Figure RL.1

English-6

Screen Rotation

Before rotating, the screen must be raised to the highest level and tilt to avoid knocking the screen on the desk or pinching your

ﬁngers. Disconnect all cables.

To raise the screen, place hands on each side of the monitor and lift up to the highest position (Figure RL.1).

To rotate screen, place hands on each side of the monitor screen and turn clockwise from Landscape to Portrait or counter-

clockwise from Portrait to Landscape (Figure R.1).

To rotate OSD menu between landscape and portrait, refer to “Controls” section.

Figure R.1

Tilt

Grasp top and bottom sides of the monitor screen with your hands and adjust the tilt as desired (Figure TS.1).

Figure TS.1

NOTE:

Handle with care when tilting the monitor screen.

Swivel

Grasp both sides of the monitor screen with your hands and adjust the swivel as desired (Figure TS.2).

Figure TS.2

English-7

Remove Monitor Stand for Mounting

To prepare the monitor for alternate mounting purposes:

1. Disconnect all cables.

2. Place hands on each side of the monitor and lift up to the highest position.

3. Place monitor face down on a non-abrasive surface (Figure S.1).

4. Place one hand around the base and one hand on the Quick Release Lever.

Push and hold the Quick Release Lever in the direction indicated by the arrows

(Figure S.1).

5. Lift up the stand to unhook it from the monitor (Figure S.1).

The monitor can now be mounted using an alternate method.

Reverse process to reattach stand.

NOTE:

Handle with care when removing monitor stand.

Figure S.1

Flexible Arm Installation

This LCD monitor is designed for use with a ﬂexible arm.

1. Follow the instructions on how Remove Monitor Stand for

Mounting to remove the stand.

2. Using the 4 screws from the stand removal and attach the arm to

the monitor (Figure F.1).

Caution: Use ONLY the screws (4 pcs) that are included or the

screws M4 size (Length: bracket thickness + 10-12 mm)

when mounting to avoid damage to the monitor and stand.

To fulﬁl the safety requirements the monitor must be

mounted to an arm which guaranties the necessary

stability under consideration of the weight of the monitor.

The LCD monitor should only be used with an approved

arm (e.g. GS mark).

200 mm*²100 mm

Unit

Mounting

Bracket

Washer

Screw

10-12 mm

Thickness

of bracket

and washer

100 mm

Weight of LCD assembly: 7.4 kg (PA241W)

9.6 kg (PA271W)

NOTE:

Tighten all screws.

(recommended Fasten Force: 98 - 137N•cm)

Figure F.1

*2 Only for PA271W.

English-8

Controls

OSD (On-Screen Display) control buttons on the front of the monitor

function as follows:

To access OSD menu, press the MENU button.

To change signal input, press the SELECT button.

NOTE:

OSD must be closed in order to change signal input.

Landscape

Portrait

1 AUTO DIMMING

SENSOR

Detects the level of ambient lighting allowing the monitor to make adjustments to various

settings resulting in a more comfortable viewing experience. Do not cover this sensor.

2 Power

3 LED

Turns the monitor on and off.

Indicates that the power is on.

Can be changed between blue and green in the Advanced OSD menu.

4 INPUT/SELECT

Enters the OSD Control menu. Enters OSD sub menus.

Changes the input source when not in the OSD Control menu.

Hold the button to show USB selection menu when not in the OSD Control menu*¹.

NOTE: This USB selection setting back to the current setting by OSD menu when you change

input signal or turn off the monitor.

5 MENU/EXIT

6 LEFT/RIGHT

Access OSD menu. Exits the OSD sub menu. Exits OSD Control menu.

Navigates to the left or right through the OSD Control menu.

You can adjust the brightness directly, while the OSD menu is off*¹.

7 UP/DOWN

8 RESET/PIP

Navigates up or down through the OSD Control menu.

Show Picture Mode menu when not in the OSD Control menu*^1,*².

Resets the OSD back to factory settings in the OSD control menu.

PIP can be selected when the OSD is not showing*³.

Hold the button to show ECO Mode menu while the OSD menu is OFF*¹.

9 KEY GUIDE

The Key Guide appears on screen when the OSD control menu is accessed.

The Key Guide will rotate when the OSD control menu is rotated*.

* The “LEFT/RIGHT” and “UP/DOWN” buttons functionality is interchangeable depending on the orientation

(Landscape/Portrait) of the OSD.

*¹When HotKey function is OFF, this function is disabled.

*²PICTURE MODE menu.

Press the UP/DOWN button to select PICTURE MODE. In PIP or PICTURE BY PICTURE mode, picture mode can

be selected for main and sub window independently by pressing Left/Right button.

*³PIP mode menu.

Press the UP/DOWN button to select sub-window ON/OFF. Press the LEFT/RIGHT button to swap main window

and sub window.

SETTING OSD LANGUAGE

•

Use the control keys (LEFT/RIGHT or UP/DOWN or MENU) to access the “LANGUAGE SELECTION” menu.

Press the LEFT/RIGHT or UP/DOWN buttons to select the desired OSD language.

To exit from this OSD menu, press EXIT button.

NOTE:

Setting the OSD language is only necessary upon initial setup. The OSD language will stay the same until changed

by the user.

English-9

Brightness/Contrast Controls

BRIGHTNESS

Adjusts the overall image and background screen brightness.

NOTE: The brightness level is adjusted using the backlight output.

The display will digitally compensate for low or high brightness levels.

If digital compensation occurs, the brightness value on the OSD will change to magenta.

NOTE: The optimal display performance will be in the range where the OSD brightness value is black. When the

display cannot achieve the desired brightness, the numerical brightness value on the OSD will blink.

NOTE: For low brightness settings, the display will automatically compensate by adjusting the screen contrast to

achieve the desired brightness. This will result in a reduced contrast ratio and the OSD indicator will change

to magenta.

NOTE: For high brightness settings, the display will automatically compensate by turning down uniformity

compensation in order to achieve the desired brightness. The OSD indicator will change to magenta and this

may result in decreased uniformity.

CONTRAST (Analog input only)*¹

Adjusts the overall image and background screen brightness by input signal level.

NOTE: It is recommended to use BRIGHTNESS to adjust screen brightness for lower power consumption and

improved image quality.

ECO MODE

Decreases the amount of power consumed by reducing the brightness level.

OFF: No function.

MODE1: Decreases the brightness range up to 200 cd/m².

MODE2: Decreases the brightness range up to 100 cd/m².

BLACK

Adjusts the black luminance.

When low settings are selected that cannot be displayed, the indicator on the OSD will turn magenta.

Auto Adjust (Analog input only)*¹

AUTO ADJUST

Automatically adjusts the Image Position and H. Size settings and Fine settings.

AUTO CONTRAST

Adjusts the image displayed for non-standard video inputs.

Image Controls

LEFT / RIGHT

Controls Horizontal Image Position within the display area of the LCD.

DOWN / UP

Controls Vertical Image Position within the display area of the LCD.

H.SIZE (V.SIZE) (Analog input only)*¹

Adjusts the horizontal size by increasing or decreasing this setting.

If the “AUTO Adjust function” do not give you a satisfactory picture setting, a further tuning can be performed using the

“H.Size (or V.Size)” function (dot clock). For this a Moiré test pattern could be used. This function may alter the width of

the picture. Use Left/Right Menu to center the image on the screen. If the H.Size (or V.Size) is wrongly calibrated, the

result would look like the left drawing. The image should be homogeneous.

When H.SIZE value is

wrong.

When H.SIZE value is

improved.

When H.SIZE value is

correct.

*1 Only for PA241W.

English-10

FINE (Analog input only)*¹

Improves focus, clarity and image stability by increasing or decreasing this setting.

If the “Auto Adjust function” and the “H.Size” function do not give you a satisfactory picture setting, a ﬁne tuning can be

performed using the “Fine” function.

For this a Moiré test pattern could be used. If the Fine value is wrongly calibrated, the result would look like the left

drawing. The image should be homogeneous.

When FINE value is

wrong.

When FINE value is

correct.

AUTO FINE (Analog input only)*¹

This function automatically and periodically adjusts the “FINE” setting for change in signal condition.

This function adjusts approximately every 33 minutes.

EXPANSION

Sets the zoom method.

FULL: The image is expanded to full screen, regardless of the resolution.

ASPECT: The image is expanded without changing the aspect ratio.

OFF: The image is not expanded.

CUSTOM: Refer to the Advanced OSD menu for detailed instructions.

SHARPNESS

This function is digitally capable of keeping crisp image at any time. It is continuously adjustable to get as distinct or as

soft an image as your prefer and set independently by different timings.

Color Control Systems

PICTURE MODE

Change the Picture mode that is most suitable for the type of content that is shown. You can change up to 5 types.

See Advanced menu Tag1 PICTURE MODE (page 16) and “Using the PICTURE MODE function” (page 15) for more

information.

WHITE

Adjust the white temperature by NATIVE or increasing or decreasing this setting. A lower color temperature will make

the screen reddish and a higher color temperature will make the screen bluish. NATIVE is a default color temperature

of LCD panel. 6500K is recommended for general graphic design and 5000K is recommended for print matching.

ADJUST

HUE: Adjusts the hue of each color*². The change in color will appear on screen and the menu color bars will show the

amount of adjustment.

OFFSET: Adjusts the color brightness of each color*². Press “RIGHT” button and the color brightness increases.

SATURATION: Adjusts the color depth of each color*². Press the “RIGHT” button and the color vividness increases.

*2: RED, YELLOW, GREEN, CYAN, BLUE and MAGENTA.

ADVANCED SETTING

Shows ADVANCED MENU. See page 16 for detailed information. Set PICTURE MODE in detail in Advanced manual

Tag1.

*1 Only for PA241W.

English-11

Tools

PIP MODE

Select PIP MODE, OFF/PIP/PICTURE BY PICTURE - ASPECT/PICTURE BY PICTURE - FULL.

You can select individual PICTURE MODE in each screen.

This display can display 2 inputs at a time.

PICTURE BY

OFF

PIP

PICTURE - ASPECT

PICTURE - FULL

IMAGE ROTATION: ON

PICTURE BY

PICTURE - ASPECT

PICTURE BY

PICTURE - FULL

OFF*¹

PIP*¹

PIP INPUT

Selects the PIP input signal.

PIP LEFT/RIGHT

Controls the horizontal position of the Picture in Picture window in PIP mode.

PIP DOWN/UP

Controls the vertical position of the Picture in Picture window in PIP mode.

PIP SIZE

Selects the size of the sub-picture used in PIP mode.

USB SELECTION

Change USB upstream input associated with the current display input, 1 or 2. When connecting a computer to each

of the upstream ports, the monitor's USB downstream ports can be used by selecting this setting for the current input

signal.

You can set the USB selection for each input signals in Advanced menu (see page 20).

When using only one upstream port, the connected upstream port is used by default.

EDID EXTENSION (DVI Input Only)

A communication setting with input device, containing signal timing.

NORMAL: When a PC or other computer equipment is connected, select “NORMAL”.

ENHANCED: Alternate setting for non-PC devices such as DVD players or game consoles. When a DVD player or

other type of high deﬁnition device is connected, select “ENHANCED”.

NOTE: Interlaced signals (480i, 576i, 1080i) are not supported. If you have any problems, please refer to the

Troubleshooting section of this User’s Manual.

When EDID EXTENSION has been changed, the connected equipment has to be restarted.

VIDEO DETECT

Selects the method of video detection when more than one video input is connected.

FIRST: When current video input signal is not present, then the monitor searches for a video signal from the other

video input port. If the video signal is present in the other port, then the monitor switches the video source input port

to the new found video source automatically. The monitor will not look for other video signals while the current video

source is present.

LAST: When the monitor is displaying a signal from the current source and a new secondary source is supplied to

the monitor, then the monitor will automatically switch to the new video source. When current video input signal is not

present, then the monitor searches for a video signal from the other video input port. If the video signal is present in the

other port, then the monitor switches the video source input port to the new found video source automatically.

NONE: The Monitor will not search the other video input port unless the monitor is turned on.

OFF TIMER

Monitor will automatically power-down when the end user has selected a pre-determined amount of time.

Before powering off, a message will appear on the screen asking the user if they want to delay the turn off time

by 60 minutes. Press any OSD button to delay the power-down time.

*1 Only for PA241W.

English-12

OFF MODE

The Intelligent Power Manager allows the monitor to enter into a power saving mode after a period of inactivity.

The OFF MODE has three settings.

OFF: Monitor does not go into power save mode when the input signal is lost.

STANDARD: Monitor enters power save mode automatically when the input signal is lost.

OPTION: Monitor enters power save mode automatically when the amount of surrounding light goes below the level

that is determined by the user. The level can be adjusted in Tag 7 of the Advanced OSD menu.

When in power save mode, the LED on the front of the monitor blinks amber. While in power save mode, push any of

the front buttons, except for POWER and SELECT to return to normal.

When the amount of surrounding light returns to normal levels, the monitor will automatically return to normal mode.

MENU Tools

LANGUAGE

OSD control menus are available in eight languages.

OSD LEFT/RIGHT

You can choose where you would like the OSD control image to appear on your screen. Selecting OSD Location

allows you to manually adjust the position of the OSD control menu left or right.

OSD DOWN/UP

You can choose where you would like the OSD control image to appear on your screen. Selecting OSD Location

allows you to manually adjust the position of the OSD control menu Up or Down.

OSD TURN OFF

The OSD control menu will stay on as long as it is use. You can select how long the monitor waits after the last touch

of a button to shut off the OSD control menu. The preset choices are 10-120 seconds by 5-second increments.

OSD LOCK OUT

This control completely locks out access to all OSD control functions. When attempting to activate OSD controls while

in the Lock Out mode, a screen will appear indicating the OSD controls are locked out.

There are four types of OSD LOCK OUT:

OSD LOCK OUT with no control: To activate the OSD Lock Out function, press SELECT, then “Right” button and

hold down simultaneously. To deactivate the OSD Lock Out, press SELECT, then “Right” button and hold down

simultaneously while in the OSD menu. No controls can be adjusted while in the lock out mode.

OSD LOCK OUT with BRIGHTNESS (only) control: To activate the OSD Lock Out function, press SELECT, then

“Down” and “Left” buttons and hold down simultaneously. To deactivate the OSD Lock Out, press SELECT, then

“Down” and “Left” buttons and hold down simultaneously while in the OSD menu. BRIGHTNESS can be adjusted while

in this lock out mode.

CUSTOM: Refer to the Advanced OSD Menu.

OSD TRANSPARENCY

Adjusts the transparency of the OSD Menu.

OSD COLOR

Adjusts the color of the OSD Menu. “Tag window frame color”, “Item select color” and “Adjust window frame color” can

be changed to Red, Green, Blue, or Gray.

RESOLUTION NOTIFIER

This optimal resolution is 1920 x 1200 for PA241W or 2560 x 1440 for PA271W. If ON is selected, a message will

appear on the screen after 30 seconds, notifying you that the resolution is not at 1920 x 1200 for PA241W or

2560 x 1440 for PA271W.

HOT KEY

You can adjust the BRIGHTNESS directly. When this function is set to ON, you can adjust the brightness with “Left” or

“Right”, while the OSD menu is off. The standard OSD can be accessed with the EXIT button. When this function is set

to OFF, some buttons are disabled (see page 9).

English-13

FACTORY PRESET

Selecting Factory Preset allows you to reset all OSD control settings (BRIGHTNESS, CONTRAST*¹, ECOMODE,

BLACK, IMAGE CONTROL, COLOR CONTROL SYSTEM, SHARPNESS, PIP MODE, PIP INPUT, PIP LEFT/RIGHT,

PIP DOWN/UP, PIP SIZE, USB SELECTION, EDID EXTENSION, OFF TIMER, OFF MODE, OSD LEFT/RIGHT,

OSD UP/DOWN, OSD TURN OFF, OSD TRANSPARENCY) back to the factory settings. Individual settings can be

reset by highlighting the control to be reset and pressing the RESET button.

NOTE: If you want reset to include the Picture calibration settings and SELF COLOR CORRECTION settings,

please use Factory Preset in Advanced OSD menu (see page 21).

ECO Information

CARBON SAVINGS: Displays the estimated carbon savings information in kg.

COST: Displays the electricity cost savings in balance.

CARBON CONVERT SETTING: Adjusts the carbon footprint factor in the carbon saving calculation. This initial setting

is based on the OECD (2008 Edition).

CURRENCY SETTING: Displays electricity pricing (available in 6 currency units).

CURRENCY CONVERT SETTING: Allows for localization of the electricity costs for accurate information in the

electrical rate savings.

NOTE: How to change Currency setting & Currency Convert setting for Cost Meter.

This model’s initial setting is Currency setting = US$ and its Currency Convert setting = $0.11.

This setting can be changed using the ECO information menu.

If you want to use the French setting, please refer to steps below:

1. Open menu by pressing the Menu button and select the ECO information menu using the left or right key.

2. Select Currency setting item pressing the Up or Down key.

3. French’s currency unit is Euro ( ), adjust currency setting to Euro icon ( ) from US dollar ($) icon

using the Left or Right key in Current setting item.

4. Select Currency Convert Setting item using the Up or Down key.

5. This initial Euro ( ) setting is Germany of OECD (2007 Edition).

6. Please check receipt of French’s electricity prices or OECD data for French.

French of OECD (2007 Edition) was 0.12.

7. Adjust Currency Convert Setting item using the Right or Left key.

Information

Provides information about the current resolution display (Main picture), current USB input setting and technical data

including the preset timing being used and the horizontal and vertical frequencies. Indicates the model and serial

numbers of your monitor.

OSD Warning

OSD Warning menus disappear with EXIT button.

NO SIGNAL: This function gives a warning when there is no Horizontal or Vertical Sync. After power is turned on or

when there is a change of input signal, the No Signal window will appear.

RESOLUTION NOTIFIER: This function warms if resolution other than the optimized resolution is used. After power is

turned on or when there is a change of input signal or the video signal doesn’t have proper resolution, the Resolution

Notiﬁer window will open. This function can be disabled in the MENU Tools.

OUT OF RANGE: This function gives a recommendation of the optimized resolution and refresh rate. After the power

is turned on or there is a change of input signal or if the video signal doesn’t have proper timing, the Out Of Range

menu will appear.

LUMINANCE WARNING: When the backlight cannot display the desired luminance, a message will appear on the

display. To avoid this, reduce the BRIGHTNESS level.

INTERLACED SIGNALS ARE NOT SUPPORTED: This function gives a warning when the interlace signal is used.

While the image is visible, change the signal of the device from interlaced to progressive (non-interlaced).

See “No Picture” in Troubleshooting for detailed information.

If you need detailed information about the controls, please use the ADVANCED OSD menu.

*1 Only for PA241W.

English-14

Using the PICTURE MODE function

Choose the Picture mode that is most suitable for the type of content that is shown.

There are several types of mode (sRGB, Adobe^®RGB, DCI, REC-Bt709, HIGH BRIGHT, FULL, DICOM, PROGRAMMABLE).

•

Each PICTURE MODE includes BRIGHTNESS, WHITE, Color Gamut, GAMMA, BLACK, UNIFORMITY, COLOR VISION

EMU, METAMERISM, RESPONSE IMPROVE settings. You can change these settings in Tag1 advanced menu.

The type of PRESET

PRESET

sRGB

PURPOSE

Standard color space used for the Internet, Windows operating systems and digital cameras. Recommended setting

for general color management.

Adobe^®RGB

Provides a standard color space used in high-end graphics applications such as professional digital still cameras and

imaging.

DCI

Color setting for digital cinema.

REC-Bt709

HIGH BRIGHT

FULL

Color setting for High-deﬁnition television.

Factory setting. Highest brightness setting. Provides lowest power consumption when kept at factory setting.

Native display color gamut. Suitable for use with color managed applications. Use ICC color proﬁle included in the

enclosed CD-ROM.

DICOM

Medical settings for X-ray imaging view. Setting that conforms to the DICOM standard for the Grayscale Standard

Display Function.

PROGRAMMABLE

For “MultiProﬁler” software or the Hardware Calibration settings (some OSD settings are disabled).

NOTE:

- When selected PICTURE MODE is different from your computer’s ICC color proﬁle, you may experience inaccurate

color reproduction.

- MultiProﬁler software, developed by NEC Display Solutions, is highly recommended to provide extended color

management features such as ICC proﬁle Emulation and Printer Emulation. MultiProﬁler software is included with

the provided CD-ROM. Also, the latest MultiProﬁler software is available on website.

- When PICTURE MODE is locked, “PICTURE MODE IS LOCKED” appears on screen. To unlock PICTURE MODE

settings, press “SELECT” and “UP” buttons at the same time.

English-15

Advanced OSD

If you need detailed information about the controls, please use the advanced menu.

There are 2 ways to access the advanced menu.

Way 1:

•

Press the Menu button to access OSD menu. Use the front buttons to move the cursor to the ADVANCED SETTING in Color

control systems. Press INPUT button to appear advanced menu.

Press the EXIT button.

•

Way 2:

•

Turn off the monitor.

•

Turn on the monitor by pushing the “POWER” and “INPUT/SELECT” button at the same time for at least one second

simultaneously. Then press the control buttons (EXIT, LEFT, RIGHT, UP, DOWN).

•

The Advanced menu will appear.

This menu is larger than the normal OSD.

Turn off and restart the monitor in the normal way.

•

To make an adjustment, ensure that the tag is highlighted, then press “SELECT”.

To move to another tag, press “EXIT”, then press “Left” or “Right” to highlight another tag.

Tag1

PICTURE MODE

PRESET

Selects PICTURE MODE, one of 1 to 5.

Sets PICTURE MODE PRESET from the type of PRESET (see page 15).

BRIGHTNESS

Adjusts the overall image and screen background brightness.

Press “Left” or “Right” to adjust.

WHITE

Adjusts the white color by temperature or xy setting. A lower color temperature will make

the screen reddish and a higher color temperature will make the screen bluish. A stronger

x makes the screen reddish, a stronger y makes it greenish and weak xy makes it a

bluish white.

English-16

GAMMA

Allows you to manually select the brightness level of grayscale. There are ﬁve selections:

sRGB, L Star, DICOM, PROGRAMMABLE and CUSTOM. We recommend to show

grayscale image data on screen.

sRGB: GAMMA setting for sRGB.

L Star: GAMMA for Lab color space.

DICOM: DICOM GSDF (Grayscale Standard Display Function) is typically used for

medical imaging.

PROGRAMMABLE: The brightness of grayscale can be changed to your preference

by downloading the application software. You can select this when PICTURE MODE is

PROGRAMMABLE. This function could not select on Advanced OSD menu.

CUSTOM: CUSTOM VALUE can be adjusted when CUSTOM is selected as the GAMMA

SELECTION setting.

CUSTOM VALUE: The gamma value is selected from the rate of 0.5 to 4.0 by 0.1 steps.

BLACK

Adjusts the black luminance. When the selected settings are too low to be displayed,

the indicator on the OSD will turn magenta.

RED

GREEN

BLUE

Adjusts color gamut. When the selected settings are outside of the LCD gamut, the

indicator on the OSD will turn magenta.

COLOR VISION EMU Previews various typical human vision deﬁciencies and is useful for evaluating how

people who have such deﬁciencies will perceive colors. This preview is available in four

modes: Types P (Protanopia), D (Deutanopia) and T (Tritanopia) emulate color vision

dichromacy, and Grayscale can be used for evaluating contrast legibility.

UNIFORMITY

This function electronically compensates for the slight variations in the white uniformity

level as well as for deviations in color that may occur throughout the display area of

the screen. These variations are characteristic of LCD panel technology. This function

improves the color and evens out the luminance uniformity of the display.

NOTE: Using the UNIFORMITY feature does reduce the overall peak luminance of the

display. If greater luminance is desired over the uniform performance of the display,

then UNIFORMITY should be turned off. A higher number produces a better effect, but

may also reduce CONTRAST RATIO. When BRIGHTNESS is shown in magenta, the

UNIFORMITY setting is automatically changed.

English-17

Tag2

SHARPNESS

This is a digital capability for keeping a crisp image at all signal timings. It continuously

adjusts to maintain as distinct or as soft image as you prefer, and is set independently

according to different timings. Press “Left” or “Right” to adjust.

RESPONSE

IMPROVE

Turns the Response Improve function on or off. Response Improve may reduce blurring

that occurs in some moving images.

ECO MODE

Decreases the amount of power consumed by reducing the brightness level.

OFF: No function.

MODE1: Decreases the maximum brightness up to 200 cd/m².

MODE2: Decreases the maximum brightness up to 100 cd/m².

AUTO BRIGHTNESS Auto Brightness has three settings.

“OFF” is recommended for best color reproduction.

OFF: No function.

ON: Adjusts the brightness automatically, by detecting the brightness level of your

environment and adjusting the monitor with the best BRIGHTNESS setting*¹.

*1: Please refer to Page 32 for full “Auto Brightness” information.

Note: Do not cover environmental brightness sensor (AUTO DIMMING sensor).

METAMERISM

Improves the white point color matching when the display used side-by-side with a

standard gamut display monitor. This feature compensates for the way the human eye

perceives colors slightly differently compared to the scientiﬁc instrument used to adjust

the display during calibration.

AMBIENT LIGHT

COMP.

Luminance setting depends on ambient light compensation.

Mostly affects black reproduction.

NOTE: AUTO DIMMING SENSOR measures ambient brightness when power is on and

affects image and color quality settings.

NOTE: Do not cover environmental brightness sensor (AUTO DIMMING sensor).

6 - AXIS ADJUST

HUE: Adjusts the hue of each color*¹. The change in color will appear on screen and the

menu color bars will show the amount of adjustment.

SATURATION: Adjusts the color depth of each color*¹. Press the “RIGHT” button and the

color vividness increases.

OFFSET: Adjusts the color brightness of each color*¹. Press “RIGHT” button and the

color Brightness increases.

*1: RED, YELLOW, GREEN, CYAN, BLUE and MAGENTA.

SHORTCUT

CUSTOM

You can select the PICTURE MODE which are displayed in PICTURE MODE shortcut

menu.

Tag3

R-H.position*¹

(Analog input only)

Adjusts the position of the red component of the image.

Press “Left” or “Right” to adjust.

G-H.position*¹

(Analog input only)

Adjusts the position of the green component of the image.

Press “Left” or “Right” to adjust.

B-H.position*¹

(Analog input only)

Adjusts the position of the blue component of the image.

Press “Left” or “Right” to adjust.

R-FINE*¹

(Analog input only)

Adjusts the “FINE” setting of the RED component of the image.

Press “Left” or “Right” to adjust.

G-FINE*¹

(Analog input only)

Adjusts the “FINE” setting of the GREEN component of the image.

Press “Left” or “Right” to adjust.

B-FINE*¹

(Analog input only)

Adjusts the “FINE” setting of the BLUE component of the image.

Press “Left” or “Right” to adjust.

R-SHARPNESS*¹

(Analog input only)

Adjusts the sharpness of the red component of the image.

Press “Left” or “Right” to adjust.

G-SHARPNESS*¹

(Analog input only)

Adjusts the sharpness of the green component of the image.

Press “Left” or “Right” to adjust.

B-SHARPNESS*¹

(Analog input only)

Adjusts the sharpness of the blue component of the image.

Press “Left” or “Right” to adjust.

DVI Long Cable

(DVI input only)

Compensates for image degradation caused by using a long DVI cable.

There are 4 possible settings, with “0” being the lowest level of compensation and “3”

being the highest level. The default setting is “1”.

*1 Only for PA241W.

English-18

Tag4*¹

(Analog

AUTO ADJUST*²

SIGNAL ADJUST

Automatically adjusts the Image Position and H.Size settings and Fine settings.

Press “SELECT” to activate Auto Adjustment. Please use test pattern, which is included

in the enclosed CD-ROM.

input only)

Determines when the auto adjustment is activated automatically.

The choices are “SIMPLE” and “FULL”. Press “Left” or “Right” to select.

H-size, Fine, H/V Position Contrast

SIMPLE

FULL

O: Automatic Adjustment X: No Automatic Adjustment

NOTE: Automatic Adjustment does not work at resolutions less than 800x600 resolution.

AUTO ADJUST

LEVEL

Determines the automatic adjustment level for Auto Adjust. The choices are “SIMPLE”,

“FULL” and “DETAIL”. Press “Left” or “Right” to select. Refer to the below table.

Size, Fine, Position

Contrast

Black Level

Time

SIMPLE

FULL

1 second

1.5 seconds

5 seconds

DETAIL*

O: Automatic Adjustment X: No Automatic Adjustment

* “DETAIL” activates automatic long cable (skew, peaking) adjustment.

A-NTAA SW

The Advanced No Touch Auto Adjust function is able to recognize new signals even

when neither the resolution nor the refresh rate has changed. If several PCs are

connected to the monitor, and each transmit very similar (or even the same) signals in

terms of resolution and refresh rates, the monitor recognizes that there is a new signal

and automatically optimizes the picture without the need for any action on the part of the

user.

OFF: A-NTAA is disabled.

ON: If a change in signal is detected A-NTAA will adjust the monitor to the optimal

settings for the new signal. If no change in the signal is detected then A-NTAA does not

activate. The screen will be blank while the monitor optimizes the signal.

OPTION: Functions the same as ON, except that the screen does not go blank when the

monitor makes adjustments for changes in signal, allowing the monitor to display the new

signal faster. When using an external switching device to connect 2 or more PCs to the

monitor, using the ON or OPTION settings is suitable.

AUTO CONTRAST*²Adjusts the image displayed for non-standard video inputs. Press “SELECT” to adjust.

Any adjustment requires the image to have white portions.

CONTRAST

Adjusts the image brightness and contrast in relation to the background.

Press “Left” or “Right” to adjust.

AUTO BLACK LEVEL*²Automatically adjusts the black level. Any adjustment requires the image to have black

portions. Press “SELECT” to activate Auto Adjust.

BLACK LEVEL

H.POSITION

Adjusts the RGB black level by input signal level.

Tag5

Controls Horizontal Image Position within the display area of the LCD.

Press “Left” or “Right” to adjust.

V.POSITION

Controls Vertical Image Position within the display area of the LCD.

Press “Left” or “Right” to adjust.

H.SIZE*¹

Adjusts the horizontal size of the screen.

(Analog input only)

If the “AUTO Adjust function” do not give you a satisfactory picture setting, a further

tuning can be performed using the “H.Size (V.Size)” function (dot clock). For this a Moiré

test pattern could be used. This function may alter the width of the picture. Use left/Right

Menu to center the image on the screen. If the H.Size (V.Size) is incorrectly calibrated,

vertical bands will appear. The image should be homogeneous.

FINE*¹

(Analog input only)

Improve focus, clarity and image stability by increasing or decreasing this setting.

If the “Auto Adjust function” and the “H.Size” function do not give you a satisfactory

picture setting, a ﬁne tuning can be performed using the “Fine” function. For this a Moiré

test pattern could be used. If the Fine value is incorrectly calibrated, horizontal lines will

appear on the display. The image should be homogeneous.

AUTO FINE*¹

(Analog input only)

This function automatically and periodically adjusts the “FINE” setting for change in signal

condition. This function adjusts approximately every 33 minutes.

H.RESOLUTION

Adjusts the horizontal size by increasing or decreasing the setting.

Press “Right” button to expand the width of the image on the screen.

Press “Left” button to narrow the width of the image on the screen.

*1 Only for PA241W.

*2 This item does not reset by FACTORY PRESET (Tag7).

English-19

V.RESOLUTION

EXPANSION

Adjusts the vertical size by increasing or decreasing the setting.

Press “Right” button to expand the height of the image on the screen.

Press “Left” button to narrow the height of the image on the screen.

Sets the zoom method.

FULL: The image is expanded to full screen, regardless of the resolution.

ASPECT: The image is expanded without changing the aspect ratio.

OFF: The image is not expanded.

CUSTOM: When CUSTOM is selected as the Expansion mode, it becomes possible to

adjust the H. ZOOM., V. ZOOM, and ZOOM POS.

SIDE BORDER

COLOR

Adjusts the side black bars color between black and white.

Tag6

USB SELECTION

USB UP Stream Port Selection for DP/DVI-1/DVI-2/D-SUB. When connecting a computer

to each of the upstream ports, the monitor’s USB downstream ports can be used by

selecting this setting for the current input signal. When using only one upstream port, the

connected upstream port is active.

EDID EXTENSION

(Digital Input Only)

A communication setting with input device, containing signal timing.

NORMAL: When a PC or other computer equipment is connected, select “NORMAL”.

Enhanced: Alternate setting for non-PC devices such as DVD players or game consoles.

Note: Interlaced signals (480i, 576i, 1080i) are not supported. If you have any problems,

please refer to the Troubleshooting section of this User’s Manual.

When EDID EXTENSION has been changed, the connected equipment has to be

restarted.

VIDEO DETECT*²

Selects the method of video detection when more than one computer is connected.

Press “Left” or “Right” to select.

FIRST: When current video input signal is not present, then the monitor searches for

a video signal from the other video input port. If the video signal is present in the other

port, then the monitor switches the video source input port to the new found video source

automatically. The monitor will not look for other video signals while the current video

source is present.

LAST: When the monitor is displaying a signal from the current source and a new

secondary source is supplied to the monitor, then the monitor will automatically switch to

the new video source. When current video input signal is not present, then the monitor

searches for a video signal from the other video input port. If the video signal is present

in the other port, then the monitor switches the video source input port to the new found

video source automatically.

NONE: The Monitor will not search the other video input port unless the monitor is

turned on.

OFF TIMER

OFF MODE

Monitor will automatically turn off after the preset time period from power on with the

ON/OFF function. When you select “ON”, press “SELECT” and “Left” or “Right” to adjust.

Before powering off, a message will appear on the screen asking the user if they want to

delay the turn off time by 60 minutes. Press any OSD button to delay the turn off time.

The Intelligent Power Manager allows the monitor to enter into a power saving mode after

a period of inactivity. The OFF MODE has three settings.

OFF: Monitor does not go into power save mode when the input signal is lost.

STANDARD: Monitor enters power save mode automatically when the input signal is lost.

OPTION: Monitor enters power save mode automatically when the amount of

surrounding light goes below the level that is determined by the user.

OFF MODE SETTING Adjusts the ILLUMINANCE value for OFF MODE. Shows illuminance.

LED BRIGHTNESS*²Controls the brightness of the power LED on the monitor.

LED COLOR*²

LANGUAGE*²

Toggles the power LED on the front between blue or green.

Tag7

OSD control menus are available in eight languages. Press “Left” or “Right” to select.

OSD H.POSITION

You can choose where you would like the OSD control image to appear on your screen.

Selecting OSD Location allows you to manually adjust the position of the OSD control

menu left or right.

OSD V.POSITION

OSD TURN OFF

You can choose where you would like the OSD control image to appear on your screen.

Selecting OSD Location allows you to manually adjust the position of the OSD control

menu up or down.

The OSD control menu will stay on as long as it is use. You can select how long the

monitor waits after the last touch of a button to shut off the OSD control menu.

The preset choices are 10-120 seconds in 5 second increments.

*2 This item does not reset by FACTORY PRESET (Tag7).

English-20

OSD LOCK OUT*²

This control completely locks out access to all OSD control functions. When attempting

to activate OSD controls while in the Lock Out mode, a screen will appear indicating the

OSD controls are locked out.

There are three types of OSD LOCK OUT:

OSD LOCK OUT with no control: To activate the OSD Lock Out function, press SELECT,

then “Right” button and hold down simultaneously. To deactivate the OSD Lock Out,

press SELECT, then “Right” button and hold down simultaneously while in the OSD

menu. No controls can be adjusted while in the lock out mode.

OSD LOCK OUT with BRIGHTNESS (only) control: To activate the OSD Lock Out

function, press SELECT, then “Down” and “Left” buttons and hold down simultaneously.

To deactivate the OSD Lock Out, press SELECT, then “Down” and “Left” buttons and

hold down simultaneously while in the OSD menu. BRIGHTNESS can be adjusted while

in the lock out mode.

CUSTOM: Press RESET and EXIT to enter the CUSTOM Menu. Select ENABLE or

DISABLE for POWER KEY, INPUT SEL, HOT KEY (BRIGHTNESS), PICTURE MODE,

WARNING (RESOLUTION NOTIFIER/OSD LOCK OUT). To Deactivate the OSD Lock

Out function, press RESET and EXIT to bring up the LOCK OUT warning.

Press SELECT, SELECT, <, >, <, >, EXIT.

OSD TRANSPARENCY Adjusts the transparency of the OSD MENU.

OSD COLOR*²

“Tag window frame color”, “Item select color” & ”Adjust Window frame color” can be

changed.

BOOT LOGO*²

The NEC logo is brieﬂy displayed after the monitor is powered on. This feature can be

turned on or off in the OSD.

Note: If the “EXIT” button is kept pressed while NEC logo is displayed, the BOOT LOGO

menu will appear. It is possible to change the BOOT LOGO setting to OFF.

SIGNAL

INFORMATION*²

Signal information can be displayed in the corner of the screen.

Signal information is either “On/Off”.

RESOLUTION

NOTIFIER*²

The optimal resolution is 1920 x 1200 for PA241W or 2560 x 1440 for PA271W. If ON is

selected, a message will appear on the screen after 30 seconds, notifying you that the

resolution is not set to 1920 x 1200 for PA241W or 2560 x 1440 for PA271W.

Press “Left” or “Right” to select.

HOT KEY*²

When this function is activated; the brightness of the monitor can be adjusted without

entering the OSD menu by using the front buttons.

The “Left” or “Right” buttons adjust the brightness level.

When this function is set to OFF, some buttons are disabled. See page 9.

FACTORY PRESET*²Selecting Factory Preset allows you to reset all OSD control settings back to the factory

settings. Highlighting the control to be reset and pressing the RESET button can reset

individual settings.

Tag8

PIP MODE

Selects PIP MODE, OFF/PIP/PICTURE BY PICTURE - ASPECT/PICTURE BY

PICTURE - FULL. See page 12.

PIP INPUT

Selects the PIP input signal.

PIP LEFT/RIGHT

When you select “PIP” in PIP MODE, you can control horizontal position of PIP display

area.

PIP DOWN/UP

PIP SIZE

When you select “PIP” in PIP MODE, you can control vertical position of PIP display area.

Selects the size of the sub-picture used in PIP mode.

BLANK SIGNAL SKIP Skip no signal inputs when you change input signal with INPUT button.

OSD ROTATION

AUTO: The OSD rotates automatically when the monitor is rotated. OSD ROTATION is

set to AUTO by default.

LANDSCAPE: Display the OSD with landscape mode.

PORTRAIT: Display the OSD with portrait mode.

IMAGE ROTATION

AUTO: The display image automatically rotates according to the orientation of the

display. If “AUTO” is selected in the “OSD ROTATION” menu, the display image rotates

according to the orientation of the monitor.

OFF: The display image is not rotated. IMAGE ROTATION is set to OFF by default.

ON: The display image always rotated.

Note: For PA271W, this function is effective only if PICTURE BY PICTURE-ASPECT or

PICTURE BY PICTURE-FULL.

*2 This item does not reset by FACTORY PRESET (Tag7).

English-21

DDC/CI

DDC/CI ENABLE/DISABLE: Turns on or off the two way communication and control with

connected PC by video cable.

NOTE: Set DDC/CI to ENABLE when using hardware calibration software like

MultiProﬁler over DisplayPort, DVI or VGA.

SCREEN SAVER

Use the SCREEN SAVER to reduce the risk of image persistence.

MOTION (Default OFF): Screen image moves periodically in 4 directions in order to

reduce the risk of image retention.

Timing for MOTION can be set so the screen image moves in intervals from every

10 to 900 seconds. Timing is set in 10-second increments.

OPTION (Default REDUCED): There are two optional selections.

REDUCED: Screen image is reduced to 95% size and is moved periodically in

4 directions. Screen may appear slightly less sharp than normal. The full image appears

on the display.

NOTE: Some input signals may not be supported by REDUCED.

FULL: Screen image is set to FULL and is moved periodically in 4 directions. Screen

image goes outside of the display area in the direction that it shifts so that a portion of the

image may appear to be cut off.

NOTE: SCREEN SAVER works when ENABLE is OFF in TILE MATRIX and PIP MODE

is OFF.

Tag9

INPUT SETTING*^1,*²Video Band Width: Reduce the visual “noise” level of the input signal. It is strong

ineffective, so that a number becomes small. Press “Left” or “Right” to select.

Sync Threshold: Adjusts the slice level of a synchronization signal. Press “SELECT” to

move the adjustment menu. Adjusts the sensitivity of the separate or composite input

signals.

Try this option if the FINE adjustment does not successfully eliminate the noise.

SOG Threshold: Adjusts the sensitivity of the Sync On Green input signals. Adjusts the

slice level when separating synchronization from sync On Green signal input. Press “Left”

or “Right” to select.

Clamp position: Operating your monitor at a non-standard timing may cause images to

appear darker than normal or have color distortion. Use of the Clamp position control will

adjust images to their normal state.

TagA

TILE MATRIX

The Tile Matrix feature allows one image to be displayed over multiple screens. This

feature can be used with up to 25 monitors (5 vertical and 5 horizontal). Using Tile Matrix

requires the PC output signal be sent through a distribution ampliﬁer to each individual

monitor.

H MONITOR: Select the number of horizontal displays.

V MONITOR: Select the number of vertical displays.

MONITOR No: Select a position to expand the screen.

TILE COMP: Works in tandem with Tile Matrix to compensate for the width of the tile

bezels in order to accurately display the image.

Tile Comp with 4 monitors (black area shows monitor frames):

monitor1

monitor2

monitor1

monitor3

monitor4

monitor3

Tile Comp OFF

Tile Comp ON

NOTE: TILE MATRIX works only when PIP MODE is OFF.

*1 Only for PA241W.

*2 This item does not reset by FACTORY PRESET (Tag7).

English-22

TagB

CARBON SAVING

COST

Displays the estimated carbon savings information in kg.

Displays the electricity cost savings in balance.

CARBON CONVERT Adjusts the carbon footprint factor in the carbon saving calculation. This initial setting is

SETTING

based on the OECD (2008 Edition).

CURRENCY

SETTING*²

Displays electricity pricing (available in 6 currency units).

CURRENCY

Adjusts electricity prices-electric energy equivalent in the electrical rate saving

CONVERT SETTING calculation.

HOURS RUNNING*²Show total running time.

SELF COLOR

CORRECTION*²

Compensates for typical a LCD yellowish color shift due to long-term usage. This take

approximately 30 minutes to complete.

TagC

INFORMATION*²

Provides information about the current display resolution. Technical data, including the preset

timing currently being used and the horizontal and vertical frequencies is also displayed.

*2 This item does not reset by FACTORY PRESET (Tag7).

English-23

Recommended use

Safety Precautions and Maintenance

FOR OPTIMUM PERFORMANCE, PLEASE NOTE

THE FOLLOWING WHEN SETTING UP AND

USING THE LCD COLOR MONITOR:

•

DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose

you to dangerous shock hazards or other risks. Refer all servicing to qualiﬁed service personnel.

•

Do not spill any liquids into the cabinet or use your monitor near water.

Do not insert objects of any kind into the cabinet slots, as they may touch dangerous voltage points, which can be harmful or

fatal or may cause electric shock, ﬁre or equipment failure.

•

Do not place any heavy objects on the power cord. Damage to the cord may cause shock or ﬁre.

Do not place this product on a sloping or unstable cart, stand or table, as the monitor may fall, causing serious damage to

the monitor.

•

The power supply cord you use must have been approved by and comply with the safety standards of your country.

(Type H05VV-F 3G 1mm²should be used in Europe).

•

In UK, use a BS-approved power cord with molded plug having a black (5A) fuse installed for use with this monitor.

Do not place any objects onto the monitor and do not use the monitor outdoors.

The lamps in this product contain mercury. Please dispose according to state, local or federal law.

Do not bend power cord.

Do not use monitor in high temperatured, humid, dusty, or oily areas.

Do not cover vent on monitor.

Vibration can damage the backlight. Do not install where the monitor will be exposed to continual vibration.

If monitor or glass is broken, do not come in contact with the liquid crystal and handle with care.

Immediately turn off the power, unplug your monitor from the wall outlet and move to a safe location then refer servicing to

qualiﬁed service personnel under the following conditions. If the monitor is used in this condition, the monitor may cause fall, ﬁre

and electric shock:

•

If the monitor stand has been cracked or peeled.

If the monitor has been wobbled.

If the monitor has an unusual odor.

When the power supply cord or plug is damaged.

If liquid has been spilled, or objects have fallen into the monitor.

If the monitor has been exposed to rain or water.

If the monitor has been dropped or the cabinet damaged.

If the monitor does not operate normally by following operating instructions.

•

Allow adequate ventilation around the monitor so that heat can properly dissipate. Do not block ventilated

openings or place the monitor near a radiator or other heat sources. Do not put anything on top of monitor.

•

The power cable connector is the primary means of detaching the system from the power supply.

The monitor should be installed close to a power outlet which is easily accessible.

CAUTION

•

Handle with care when transporting. Save packaging for transporting.

Do not touch LCD panel surface while transporting, mounting and setting. Applying pressure on the LCD

panel can cause serious damage.

Image Persistence: Image persistence is when a residual or “ghost” image of a previous image remains visible on the screen.

Unlike CRT monitors, LCD monitors’ image persistence is not permanent, but constant images being displayed for a long period

of time should be avoided.

To alleviate image persistence, turn off the monitor for as long as the previous image was displayed. For example, if an image

was on the monitor for one hour and a residual image remains, the monitor should be turned off for one hour to erase the image.

NOTE: As with all personal display devices, NEC DISPLAY SOLUTIONS recommends using a moving screen saver at regular

intervals whenever the screen is idle or turning off the monitor when not in use.

English-24

CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN

REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE

FOLLOWING WHEN YOU POSITION THE MONITOR:

•

For optimum performance, allow 20 minutes for the display to warm up.

Adjust the monitor height so that the top of the screen is at or slightly below eye level.

Your eyes should look slightly downward when viewing the middle of the screen.

•

Position your monitor no closer than 40 cm (15.75 inches) and no further away than

70 cm (27.56 inches) from your eyes. The optimal distance is 50 cm (19.69 inches).

•

Rest your eyes periodically by focusing on an object at least 20 feet away. Blink often.

Position the monitor at a 90° angle to windows and other light sources to minimize glare

and reﬂections. Adjust the monitor tilt so that ceiling lights do not reﬂect on your screen.

•

If reﬂected light makes it hard for you to see your screen, use an anti-glare ﬁlter.

Clean the LCD monitor surface with a lint-free, non-abrasive cloth. Avoid using any

cleaning solution or glass cleaner!

•

Adjust the monitor’s brightness and contrast controls to enhance readability.

Use a document holder placed close to the screen.

Position whatever you are looking at most of the time (the screen or reference material) directly in front of you to minimize

turning your head while you are typing.

•

Avoid displaying ﬁxed patterns on the monitor for long periods of time to avoid image persistence (after-image effects).

Get regular eye checkups.

Ergonomics

To realize the maximum ergonomics beneﬁts, we recommend the following:

•

To avoid eye fatigue, adjust the brightness to a moderate setting. Place a sheet of white paper next to the LCD screen for

luminance reference.

•

Do not position the Contrast control to its maximum setting.

Use the preset Size and Position controls with standard signals.

Use the preset Color Setting.

Use non-interlaced signals with a vertical refresh rate of more than 60 Hz.

Do not use primary color blue on a dark background, as it is difﬁcult to see and may produce eye fatigue due to insufﬁcient

contrast.

Cleaning the LCD Panel

•

When the LCD is dusty, please gently wipe with a soft cloth.

Please do not rub the LCD panel with hard or coarse material.

Please do not apply pressure to the LCD surface.

Please do not use OA cleaner as it will cause deterioration or discoloration on the LCD surface.

Cleaning the Cabinet

•

Unplug the power supply

Gently wipe the cabinet with a soft cloth

To clean the cabinet, dampen the cloth with a neutral detergent and water, wipe the cabinet and follow with a dry cloth.

NOTE:

Many plastics are used on the surface of the cabinet. DO NOT clean with benzene, thinner, alkaline detergent,

alcoholic system detergent, glass cleaner, wax, polish cleaner, soap powder, or insecticide. Do not touch rubber or

vinyl to the cabinet for a long time. These types of ﬂuids and fabrics can cause the paint to deteriorate, crack or peel.

English-25

Speciﬁcations - PA241W

Monitor Speciﬁcations

MultiSync PA241W

Notes

LCD Module

Diagonal: 61.1 cm/24.1 inches

Viewable Image Size: 61.1 cm/24.1 inches

Native Resolution (Pixel Count): 1920 x 1200

Active matrix; thin ﬁlm transistor (TFT) liquid crystal

display (LCD); 0.270 mm dot pitch; 360 cd/m²white

luminence; 1000:1 contrast ratio, typical.

Input Signal

DisplayPort:

DisplayPort Connector: Digital RGB

DVI-D 24pin: Digital RGB

DisplayPort Complies with Standard V1.1a,

applicable to HDCP

DVI:

DVI (HDCP)

VGA:

15pin Mini D-sub: Analog RGB

Sync

0.7 Vp-p/75 ohm

Separate sync.TTL level Positive/Negative

Composite sync.TTL level Positive/Negative

Sync on Green

(Video 0.7 Vp-p and Sync Negative 0.3 Vp-p)

Display Colours

1,073,741,824

Depends on display card used.

Synchronization Range

Horizontal: 31.5 kHz to 93.8 kHz, 118.4 kHz*²(Analog)

31.5 kHz to 91.1 kHz, 118.4 kHz*²(Digital)

Vertical: 50 Hz to 85 Hz

Automatically

Viewing Angle

Left/Right:

Up/Down:

89° (CR > 10)

Image Formation Time

16 ms (Typ.)

8 ms (Gray to gray Typ)

Resolutions Supported (Some systems may

not support all modes listed).

640 x 480*¹at 60 Hz to 85 Hz

720 x 350*¹at 70 Hz to 85 Hz

720 x 400*¹at 70 Hz to 85 Hz

800 x 600*¹at 56 Hz to 85 Hz

832 x 624*¹at 75 Hz

1024 x 768*¹at 60 Hz to 85 Hz

1152 x 864*¹at 70 Hz to 85 Hz

1152 x 870*¹at 75 Hz

1152 x 900*¹at 66 Hz

1280 x 960*¹at 60 Hz

1280 x 1024*¹at 60 Hz to 85 Hz

1400 x 1050*¹at 60 Hz to 75 Hz

1440 x 900*¹at 60 Hz to 85 Hz

1600 x 1200*¹at 60 Hz to 75 Hz (Analog), 1600 x 1200*¹at 60 Hz (Digital)

1680 x 1050*¹at 60 Hz to 75 Hz (Analog), 1680 x 1050*¹at 60 Hz (Digital)

1920 x 1200 at 60 Hz............................................NEC DISPLAY SOLUTIONS cites recommended

1024 x 1280*¹at 60 Hz

resolution for optimal display performance.

1200 x 1920*¹at 60 Hz

480P (720 x 480*¹at 60 Hz)

576P (720 x 576*¹at 50 Hz)

720P (1280 x 720*¹at 50 Hz to 60 Hz)

1080P (1920 x 1080*¹at 50 Hz to 60 Hz)

Active Display Area

USB Hub

Landscape: Horiz.: 518 mm/20.4 inches

Vert.: 324 mm/12.8 inches

Portrait: Horiz.: 324 mm/12.8 inches

Vert.: 518 mm/20.4 inches

I/F: USB Speciﬁcation Revision 2.0

Port: Upstream 2

Downstream 3

Load Current: Maximum 0.5A per port

Power Supply

Current Rating

Dimensions

AC 100-240 V ~ 50/60 Hz

1.38 - 0.56A (with option)

Landscape: 556.8 mm (W) x 378 - 528 mm (H) x 227.6 mm (D)

21.9 inches (W) x 14.9 - 20.8 inches (H) x 9.0 inches (D)

Portrait: 362.4 mm (W) x 572.4 - 625.2 mm (H) x 227.6 mm (D)

14.3 inches (W) x 22.5 - 24.6 inches (H) x 9.0 inches (D)

Height Adjustment: 150 mm / 5.9 inches

Weight

10.6 kg (23.4 lbs)

Environmental Considerations

Operating Temperature: 5°C to 35°C/41°F to 95°F

Humidity: 30% to 80%

Altitude: 0 to 10,000 Feet/0 to 3,048 m

Storage Temperature: -10°C to 60°C/14°F to 140°F

Humidity: 10% to 85%

Altitude: 0 to 40,000 Feet/0 to 12,192 m

*1 Interpolated Resolutions: When resolutions are shown that are lower than the pixel count of the LCD module, text may appear different. This is normal and

necessary for all current ﬂat panel technologies when displaying non-native resolutions full screen. In ﬂat panel technologies, each dot on the screen is actually one

pixel, so to expand resolutions to full screen, an interpolation of the resolution must be done.

*2 1200 x 1920 resolution only.

NOTE:

Technical speciﬁcations are subject to change without notice.

English-26

Speciﬁcations - PA271W

Monitor Speciﬁcations

MultiSync PA271W

Notes

LCD Module

Diagonal: 68.5 cm/27.0 inches

Viewable Image Size: 68.5 cm/27.0 inches

Native Resolution (Pixel Count): 2560 x 1440

Active matrix; thin ﬁlm transistor (TFT) liquid crystal

display (LCD); 0.233 mm dot pitch; 300 cd/m²white

luminence; 1000:1 contrast ratio, typical.

Input Signal

DisplayPort:

DisplayPort Connector: Digital RGB

DisplayPort Complies with Standard V1.1a,

applicable to HDCP

DVI:

DVI-D 24pin: Digital RGB

1,073,741,824

DVI (HDCP)

Display Colours

Depends on display card used.

Synchronization Range

Horizontal: 31.5 kHz to 93.9 kHz

Vertical: 50 Hz to 87 Hz

Automatically

Viewing Angle

Left/Right:

Up/Down:

89° (CR > 10)

Image Formation Time

12 ms (Typ.)

7 ms (Gray to gray Typ)

Resolutions Supported (Some systems may

not support all modes listed).

640 x 480*¹at 60 Hz to 85 Hz

720 x 350*¹at 70 Hz to 85 Hz

720 x 400*¹at 70 Hz to 85 Hz

800 x 600*¹at 56 Hz to 85 Hz

832 x 624*¹at 75 Hz

1024 x 768*¹at 60 Hz to 85 Hz

1152 x 864*¹at 70 Hz to 85 Hz

1152 x 870*¹at 75 Hz

1152 x 900*¹at 66 Hz

1280 x 960*¹at 60 Hz

1280 x 1024*¹at 60 Hz to 85 Hz

1400 x 1050*¹at 60 Hz to 75 Hz

1440 x 900*¹at 60 Hz to 85 Hz

1600 x 1200*¹at 60 Hz

1680 x 1050*¹at 60 Hz

1920 x 1200 at 60 Hz

1024 x 1280*¹at 60 Hz

1200 x 1920*¹at 60 Hz

2560 x 1440 at 60 Hz........................................... NEC DISPLAY SOLUTIONS cites recommended

480P (720 x 480*¹at 60 Hz)

resolution for optimal display performance.

576P (720 x 576*¹at 50 Hz)

720P (1280 x 720*¹at 50 Hz to 60 Hz)

1080P (1920 x 1080*¹at 50 Hz to 60 Hz)

Active Display Area

USB Hub

Landscape: Horiz.: 597 mm/23.5 inches

Vert.: 336 mm/13.2 inches

Portrait: Horiz.: 336 mm/13.2 inches

Vert.: 597 mm/23.5 inches

I/F: USB Speciﬁcation Revision 2.0

Port: Upstream 2

Downstream 3

Load Current: Maximum 0.5A per port

Power Supply

Current Rating

Dimensions

AC 100-240 V ~ 50/60 Hz

1.64 - 0.65 A (with option)

Landscape: 640.4 mm (W) x 396.2 - 546.2 mm (H) x 235.5 mm (D)

25.2 inches (W) x 15.6 - 21.5 inches (H) x 9.3 inches (D)

Portrait: 378.6 mm (W) x 658.0 - 677.1 mm (H) x 235.5 mm (D)

14.9 inches (W) x 25.9 - 26.7 inches (H) x 9.3 inches (D)

Height Adjustment: 150 mm / 5.9 inches

Weight

13.4 kg (29.5 lbs)

Environmental Considerations

Operating Temperature: 5°C to 35°C/41°F to 95°F

Humidity: 30% to 80%

Altitude: 0 to 10,000 Feet/0 to 3,048 m

Storage Temperature: -10°C to 60°C/14°F to 140°F

Humidity: 10% to 85%

Altitude: 0 to 40,000 Feet/0 to 12,192 m

*1 Interpolated Resolutions: When resolutions are shown that are lower than the pixel count of the LCD module, text may appear different. This is normal and

necessary for all current ﬂat panel technologies when displaying non-native resolutions full screen. In ﬂat panel technologies, each dot on the screen is actually one

pixel, so to expand resolutions to full screen, an interpolation of the resolution must be done.

NOTE:

Technical speciﬁcations are subject to change without notice.

English-27

Features

DisplayPort: DisplayPort is designed to be the future-ready, scalable solution for high performance digital display connectivity.

It enables the highest resolutions, the fastest refresh rates and deepest color depths over standard cables.

DFP (Digital Flat Panel): An all-digital interface for ﬂat panel monitors which is signal compatible with DVI. As a DVI-based

digital only connection, only a simple adapter is necessary for compatibility between DFP and other DVI-based digital

connectors such as DVI and P&D.

P&D (Plug and Display): The VESA standard for digital ﬂat panel monitor interfaces. It is more robust than DFP since it

allows for other options off a signal connector (options like USB, analog video and IEEE-1394-995). The VESA committee

has recognized that DFP is a subset of P&D. As a DVI-based connector (for the digital input pins), only a simple adapter is

necessary for compatibility between P&D and other DVI-based digital connector such as DVI and DFP.

Pivoting Stand: Allows users to adjust the monitor to the orientation that best ﬁts their application, either Landscape orientation

for wide documents, or Portrait orientation for the ability to preview a full page on one screen at one time. The Portrait

orientation is also perfect for full screen video conferencing.

Reduced Footprint: Provides the ideal solution for environments requiring superior image quality but with size and weight

limitations. The monitor’s small footprint and low weight allow it to be moved or transported easily from one location to another.

Color Control Systems: Allows you to adjust the colors on your screen and customize the color accuracy of your monitor to a

variety of standards.

Natural Color Matrix: Combines Six-axis color control and the sRGB standard. Six-axis color control permits color adjustments

via six axes (R, G, B, C, M and Y) rather than through the three axes (R, G and B) previously available. The sRGB standard

provides the monitor with a uniform color proﬁle. This assures that the colors displayed on the monitor are exactly the same as

on the color printout (with sRGB supporting operating system and sRGB printer). This allows you to adjust the colors on your

screen and customise the color accuracy of your monitor to a variety of standards.

OSD (On-Screen Display) Controls: Allow you to quickly and easily adjust all elements of your screen image via simple to use

on-screen menus.

ErgoDesign Features: Enhanced human ergonomics to improve the working environment, protect the health of the user and

save money. Examples include OSD controls for quick and easy image adjustments, tilt base for preferred angle of vision, small

footprint and compliance with MPRII and TCO guidelines for lower emissions.

Plug and Play: The Microsoft^®solution with the Windows^®operating system facilitates setup and installation by allowing

the monitor to send its capabilities (such as screen size and resolutions supported) directly to your computer, automatically

optimizing display performance.

Intelligent Power Manager System: Provides innovative power-saving methods that allow the monitor to shift to a lower power

consumption level when on but not in use, saving two-thirds of your monitor energy costs, reducing emissions and lowering the

air conditioning costs of the workplace.

Multiple Frequency Technology: Automatically adjusts monitor to the display card’s scanning frequency, thus displaying the

resolution required.

FullScan Capability: Allows you to use the entire screen area in most resolutions, signiﬁcantly expanding image size.

Wide Viewing Angle Technology: Allows the user to be able to see the monitor from any angle (178°) from any orientation —

Portrait or Landscape. Provides full 178° viewing angles either up, down, left or right.

VESA Standard Mounting Interface: Allows users to connect their MultiSync monitor to any VESA standard third party

mounting arm or bracket. Allows for the monitor to be mounted on a wall or an arm using any third party compliant device.

Visual Controller: Is a ground-breaking software family, developed by NEC Display Solutions, providing intuitive access to all

monitor setting controls and remote diagnosis via the Windows interface, based upon the VESA standard, DDC/CI. Using a

standard VGA or DVI signal cable, Visual Controller can either beneﬁt single users or, with Visual Controller Administrator, can

reduce the Total Cost of Ownership through remote network-wide maintenance, diagnosis and asset-reporting.

No-touch Auto Adjust*¹(Analog input only): No-touch auto adjust automatically adjusts the monitor to optimal settings upon

initial setup.

sRGB Color Control: A new optimized color management standard which allows for color matching on computer displays

and other peripherals. The sRGB, which is based on the calibrated color space, allows for optimal color representation and

backward compatibility with other common color standards.

UNIFORMITY: This feature compensates for slight variations in the white uniformity level that may occur on the screen and

improves the color and evens out the luminance uniformity of the display.

Response Improve: Improved gray to gray response.

Adjustable stand with pivot capability: Adds ﬂexibility to your viewing preferences.

Quick Release stand: Allows fast removal.

Auto dimming technology: Automatically adjusts the backlight level depending on the level of ambient lighting.

*1 Only for PA241W.

English-28

USB 2.0 hub adds excitement to your computing by connecting you to digital cameras, scanners and more.

Environmental Impact: Annual typical maximum operating carbon footprint of this monitor (world-wide average) is

approximately ??.? kg (PA241W)/??.? kg (PA271W) (calculated by: rated wattage x 8 hours per day x 5 days a week x 45

weeks per year x Power-to-Carbon conversion factor - conversion factor is based on OECD publication of global CO2 emissions

2008 Edition).

This monitor has a manufacturing carbon footprint of approximately ??.? kg (PA241W)/??.? kg (PA271W).

Note: The manufacturing and operating carbon footprints are calculated by a unique algorithm developed exclusively by NEC for

its monitors.

English-29

Troubleshooting

No picture

•

The signal cable should be completely connected to the display card/computer.

The display card should be completely seated in its slot.

The monitor does not support DisplayPort converter signal.

Front Power Switch and computer power switch should be in the ON position.

Check to make sure that a supported mode has been selected on the display card or system being used.

(Please consult display card or system manual to change graphics mode.)

•

Check the monitor and your display card with respect to compatibility and recommended settings.

Check the signal cable connector for bent or pushed-in pins.

Check the signal input, “DVI-D”, “DisplayPort” or “D-Sub”.

If the front LED is blinking amber, check the status of the OFF MODE mode (see page 13).

When using a DVD player or any other type of high-deﬁnition device, please do not use interlaced signals. If the monitor

detects an interlaced signal, an OSD warning will appear. If this OSD warning appears, please do the following: press the

RESET and EXIT buttons simultaneously, to temporarily show the image coming from the high-deﬁnition device. While

the image is visible, change the signal of the device from interlaced to progressive (non-interlaced). Consult the User’s

Manual included with the device for detailed information on changing the signal from interlaced to progressive.

Power Button does not respond

Unplug the power cord of the monitor from the AC outlet to turn off and reset the monitor.

•

Image Persistence

•

Image persistence is when a residual or “ghost” image of a previous image remains visible on the screen. Unlike CRT

monitors, LCD monitors’ image persistence is not permanent, but constant images being displayed for a long period

of time should be avoided. To alleviate image persistence, turn off the monitor for as long as the previous image was

displayed. For example, if an image was on the monitor for one hour and a residual image remains, the monitor should

be turned off for one hour to erase the image.

NOTE:

As with all personal display devices, NEC DISPLAY SOLUTIONS recommends using a moving screen saver at

regular intervals whenever the screen is idle or turning off the monitor when not in use.

Picture is discolored

•

Make sure COLOR VISION EMU is OFF.

Make sure PICTURE MODE setting is same as ICC proﬁle on PC.

Set SELF COLOR CONTROL.

When using an analog input, display the test pattern included in the enclosed CD-ROM and set AUTO ADJUST*¹.

Color irregularities on screen

•

Reduce BRIGHTNESS.

•

Set UNIFORMITY to “5”.

Image is ﬂickering

•

When using an analog input, display the test pattern included in the enclosed CD-ROM and set AUTO ADJUST*¹.

Message “OUT OF RANGE” is displayed (screen is either blank or shows rough images only)

•

Image is displayed only roughly (pixels are missing) and OSD warning “OUT OF RANGE” is displayed: Either signal

clock or resolution is too high. Choose one of the supported modes.

•

OSD warning “OUT OF RANGE” is displayed on a blank screen: Signal frequency is out of range. Choose one of the

supported modes.

Image is unstable, unfocused or swimming is apparent

•

Signal cable should be completely attached to the computer.

•

Use the OSD Image Adjust controls to focus and adjust display by increasing or decreasing the ﬁne adjustment.

When the display mode is changed, the OSD Image Adjust settings may need to be readjusted.

•

Check the monitor and your display card with respect to compatibility and recommended signal timings.

If your text is garbled, change the video mode to non-interlace and use 60Hz refresh rate.

LED on monitor is not lit (no green, blue or amber color can be seen)

Power Switch should be in the ON position and power cord should be connected.

•

Picture is not as bright

•

Make sure ECO MODE and AUTO BRIGHTNESS are turned off.

If the brightness ﬂuctuates make sure AUTO BRIGHTNESS is turned off.

In PICTURE MODE, set HI-BRIGHT. See page 15.

LCD brightness degradation occurs due to long-term usage or extreme cold conditions.

Display image is not sized properly

•

Use the OSD Image Adjust controls to increase or decrease the Coarse adjustment.

•

Check to make sure that a supported mode has been selected on the display card or system being used.

(Please consult display card or system manual to change graphics mode.)

*1 Only for PA241W.

English-30

No Video

•

If no video is present on the screen, turn the Power button off and on again.

Make certain the computer is not in a power-saving mode (touch the keyboard or mouse).

Some video cards do not output video signal when monitor is turned OFF/ON or disconnect/connect from the AC power

cord under low resolution with DisplayPort.

•

If no video is present on the screen, check the status of the EDID EXTENSION in the User menu (see page 12), the

setting may need to be changed to allow HDCP content to be displayed.

Self Diagnosis

•

The LCD display is equipped with the ability to self diagnose abnormalities. When the LCD detects a problem, the LED

on the front ﬂashes in a pattern of long and short blinks, depending on the type of problem detected.

•

If the LED signals a problem, please refer service to qualiﬁed personnel.

USB Hub does not operate

•

Check to make sure the USB cord is properly connected. Refer to your USB devise User’s Manual.

Make sure correct upstream is selected on USB hub setting (see page 12).

Disconnect one upstream USB cable when using 2 upstream.

English-31

Using the Auto Brightness function

The brightness of the LCD screen can be set to increase or decrease depending on the amount of ambient light within the

room. If the room is bright, the monitor becomes correspondingly bright. If the room is dim, then the monitor will dim accordingly.

The purpose of this function is to make the viewing experience more comfortable to the eye in a variety of lighting conditions.

The Auto Brightness function is set to OFF by default.

SETUP

Use the following procedure to select the Brightness Range that the monitor will use when the Auto Brightness function is

activated.

1. Set the BRIGHT level. This is the brightness level that the monitor will go up to when the ambient light level is highest. Make

sure the room is at its brightest when setting this level.

Select “ON” in the AUTO BRIGHTNESS menu (Figure 1). Then use the front buttons to move the cursor up to the

BRIGHTNESS setting. Choose the desired brightness level (Figure 2).

2. Set the DARK level. This is the level of brightness that the monitor will go down to when the ambient light level is low.

Make sure the room is at its darkest when setting this level.

Then use the front buttons to move the cursor up to the BRIGHTNESS setting. Choose the desired brightness level

(Figure 3).

Figure 1

Figure 2

Figure 3

When the “Auto Brightness” function is enabled the Brightness level of the screen changes automatically according to the

lighting conditions of the room (Figure 4).

BRIGHTNESS range

BRIGHTNESS level set

for the monitor to use

when ambient lighting

level is low.

BRIGHTNESS level set for the

monitor to use when ambient

lighting level is high.

Bright condition area

room bright condition

dark

bright

Dark condition area

Screen Brightness value by Auto Brightness function

Figure 4

Lb: Border between bright and dim lighting conditions; set at factory

L1: BRIGHTNESS level set for the monitor to use when ambient lighting level is high (L1>Lb)

L2 : BRIGHTNESS level set for the monitor to use when ambient lighting level is low (L2<Lb)

L1 and L2 are the brightness levels set by the user to compensate for changes in ambient lighting.

English-32

TCO’03 (for MultiSync PA271W)

Congratulations!

The display you have just purchased carries the TCO’03 Displays

label. This means that your display is designed, manufactured and

tested according to some of the strictest quality and environmental

requirements in the world. This makes for a high performance

product, designed with the user in focus that also minimizes the

impact on our natural environment.

Some of the features of the TCO’03 Display requirements:

Ergonomics

• Good visual ergonomics and image quality in order to improve the working environment

for the user and to reduce sight and strain problems. Important parameters are luminance,

contrast, resolution, reﬂectance, color rendition and image stability.

Energy

• Energy-saving mode after a certain time – beneﬁcial both for the user and the environment

• Electrical safety

Emissions

•

Electromagnetic ﬁelds

•

Noise emissions

Ecology

• The product must be prepared for recycling and the manufacturer must have a certiﬁed

environmental management system such as EMAS or ISO 14 001

• Restrictions on:

chlorinated and brominated ﬂame retardants and polymers

heavy metals such as cadmium, mercury and lead.

The requirements included in this label have been developed by TCO Development in co-

operation with scientists, experts, users as well as manufacturers all over the world. Since the

end of the 1980s TCO has been involved in inﬂuencing the development of IT equipment in

a more user-friendly direction. Our labelling system started with displays in 1992 and is now

requested by users and IT-manufacturers all over the world.

For more information, please visit

www.tcodevelopment.com

English-33

TCO Displays 5.0 (for MultiSync PA241W)

Congratulations!

This display is designed for both you and the planet!

The display you have just purchased carries the TCO

CertiÞed label. This ensures that your display is designed,

manufactured and tested according to some of the strictest

quality and environmental requirements in the world.

This makes for a high performance product, designed with

the user in focus that also minimizes the impact on the

climate and our natural environment.

TCO CertiÞed is a third party veriÞed program, where every product model is tested by an

accredited impartial test laboratory. TCO CertiÞed represents one of the toughest certiÞcations

for displays worldwide.

Some of the Usability features of the TCO Certiﬁed for displays:

• Good visual ergonomics and image quality is tested to ensure top performance and reduce

sight and strain problems. Important parameters are luminance, contrast, resolution, black level,

gamma curve, color and luminance uniformity, color rendition and image stability.

• Product have been tested according to rigorous safety standards at an impartial laboratory.

• Electric and magnetic Þelds emissions as low as normal household background levels.

• Low acoustic noise emissions.

Some of the Environmental features of the TCO Certiﬁed for displays:

• The brand owner demonstrates corporate social responsibility and has a certiÞed

environmental management system (EMAS or ISO 14001).

• Very low energy consumption both in on- and standby mode minimize climate impact.

• Restrictions on chlorinated and brominated ßame retardants, plasticizers, plastics and

heavy metals such as cadmium, mercury and lead (RoHS compliance).

• Both product and product packaging is prepared for recycling.

• The brand owner offers take-back options.

The requirements can be downloaded from our web site. The requirements included in this

label have been developed by TCO Development in co-operation with scientists, experts,

users as well as manufacturers all over the world. Since the end of the 1980s TCO has been

involved in inßuencing the development of IT equipment in a more user-friendly direction.

Our labeling system started with displays in 1992 and is now requested by users and IT-

manufacturers all over the world. About 50% of all displays worldwide are TCO certiÞed.

For more information, please visit

www.tcodevelopment.com

English-34

Manufacturer’s Recycling and Energy Information

NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s

top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentally-

friendly products, and always strive to help deﬁne and comply with the latest independent standards from agencies such as

ISO (International Organisation for Standardization) and TCO (Swedish Trades Union).

Disposing of your old NEC product

The aim of recycling is to gain an environmental beneﬁt by means of re-use, upgrading, reconditioning or reclamation of

material. Dedicated recycling sites ensure that environmentally harmful components are properly handled and securely

disposed. To ensure the best recycling of our products, NEC DISPLAY SOLUTIONS offers a variety of recycling procedures

and gives advice on how to handle the product in an environmentally sensitive way, once it has reached the end of its life.

All required information concerning the disposal of the product and country-speciﬁc information on recycling facilities can be

found on our following websites:

http://www.nec-display-solutions.com/greencompany/ (in Europe),

http://www.nec-display.com (in Japan) or

http://www.necdisplay.com (in USA).

Energy Saving

This monitor features an advanced energy saving capability. When a VESA Display Power Management Signalling (DPMS)

Standard signal is sent to the monitor, the Energy Saving mode is activated. The monitor enters a single Energy Saving mode.

Mode

Power consumption

LED colour

Normal Operation (with option)

Approx. 146 W (PA271W)

Approx. 115 W (PA241W)

Green or blue

Normal Operation (at TCO testing)

Energy Saving Mode

Off Mode

Approx. 73 W (PA271W)

Approx. 55 W (PA241W)

Green or blue

Amber

Less than 1.1 W (PA271W)

Less than 1 W (PA241W)

Less than 0.2 W

Unlit

WEEE Mark (European Directive 2002/96/EC)

Within the European Union

EU-wide legislation, as implemented in each Member State, requires that waste electrical and electronic

products carrying the mark (left) must be disposed of separately from normal household waste. This includes

monitors and electrical accessories, such as signal cables or power cords. When you need to dispose of your

NEC display products, please follow the guidance of your local authority, or ask the shop where you purchased

the product, or if applicable, follow any agreements made between yourself and NEC.

The mark on electrical and electronic products only applies to the current European Union Member States.

Outside the European Union

If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local authority

so as to comply with the correct disposal method.

English-35

Intel Computer Hardware half size single board computer User Manual
JVC AV 21MS15 AV 29MS15 User Manual
JVC GGT0006 001A H User Manual
Lincoln Impringer Conveyor Oven 1400 User Manual
Memorex MPH2430 User Manual
Motorola D511 User Manual
NEC PX 42VP4D User Manual
Palsonic 7118 User Manual
Philips 28PW9615 User Manual
Philips SE250 User Manual