NEC Electronics America Computer Monitor PX 42XM5G User Manual

PlasmaSync Plasma Monitor

(Enhanced split screen Model)

PlasmaSync 42XM5

PX-42XM5G

PlasmaSync 50XM6

PX-50XM6G

PlasmaSync 60XM5

PX-60XM5G

User’s Manual

Benutzerhandbuch

Manuel d’utilisation

Manual del Usuario

Manuale dell’utente

ꢀуководство пользователя

Bruksanvisning

Kullanım Kılavuzu

Εγꢀειρίδι ꢁρήσης

Important Information

To avoid damage and prolong operating life:

Precautions

1. Use only with 100V to 240 V 50 Hz/60 HzAC power supply. Continued

operation at line voltages greater than 100 V to 240 V AC will shorten

the life of the unit, and might even cause a fire hazard.

2. Handle the unit carefully when installing it and do not drop.

3. Set the unit away from heat, excessive dust, and direct sunlight.

4. Protect the inside of the unit from liquids and small metal objects. In

case of accident, unplug the power cord and have it serviced by an

authorized Service Center.

Please read this manual carefully before using your plasma monitor and

keep the manual handy for future reference.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

5. Do not hit or scratch the panel surface as this causes flaws on the surface

of the screen.

6. For correct installation and mounting it is strongly recommended to

use a trained, authorized dealer.

7. As is the case with any phosphor-based display (like a CRT monitor,

for example) light output will gradually decrease over the life of a Plasma

Display Panel.

8. To avoid sulfurization it is strongly recommended not to place the unit

in a dressing room in a public bath or hot spring bath.

9. Do not use in a moving vehicle, as the unit could drop or topple over

and cause injuries.

10. Do not place the unit on its side, upside-down or with the screen facing

up or down, to avoid combustion or electric shock.

11. To prevent a fire hazard, do not place near an open flame (such as a

lighted candle).

Plasma monitor cleaning procedure:

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE COVER. NO USER-SERVICEABLE

PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

This symbol warns the user that uninsulated voltage

within the unit may have sufficient magnitude to cause

electric shock. Therefore, it is dangerous to make any

kind of contact with any part inside of this unit.

This symbol alerts the user that important literature

concerning the operation and maintenance of this unit

has been included.

Therefore, it should be read carefully in order to avoid

any problems.

1. Use a soft dry cloth to clean the front panel and bezel area. Never use

solvents such as alcohol or thinner to clean these surfaces.

2. Clean plasma ventilation areas with a vacuum cleaner with a soft brush

nozzle attachment.

WARNING

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS

UNIT TO RAIN OR MOISTURE. ALSO DO NOT USE THIS UNIT’S

POLARIZED PLUG WITHAN EXTENSION CORD RECEPTACLE OR

OTHER OUTLETS, UNLESS THE PRONGS CAN BE FULLY

INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE

ARE HIGH-VOLTAGE COMPONENTS INSIDE. REFER SERVICING

TO QUALIFIED SERVICE PERSONNEL.

3. To ensure proper ventilation, cleaning of the ventilation areas must be

carried out monthly. More frequent cleaning may be necessary

depending on the environment in which the plasma monitor is installed.

Recommendations to avoid or minimize image retention:

Like all phosphor-based display devices and all other gas plasma displays,

plasma monitors can be susceptible to image retention under certain

circumstances. Certain operating conditions, such as the continuous

display of a static image over a prolonged period of time, can result in

image retention if proper precautions are not taken. To protect your

investment in this plasma monitor, please adhere to the following

guidelines and recommendations for minimizing the occurrence of image

retention:

* Always enable and use your computer’s screen saver function

during use with a computer input source.

* Display a moving image whenever possible.

* Change the position of the menu display from time to time.

* Always power down the monitor when you are finished using it.

If the plasma monitor is in long term use or continuous operation take the

following measures to reduce the likelihood of image retention:

* Lower the Brightness and Contrast levels as much as possible without

impairing image readability.

Warnings and Safety Precaution

This plasma monitor is designed and manufactured to provide

long, trouble-free service. No maintenance other than cleaning

is required. Please see the section “Plasma monitor cleaning

procedure”.

The plasma display panel consists of fine picture

elements (cells) with more than 99.99 percent active cells. There

may be some cells that do not produce light or remain lit.

For operating safety and to avoid damage to the unit, read

carefully and observe the following instructions.

To avoid shock and fire hazards:

1. Provide adequate space for ventilation to avoid internal heat build-

up. Do not cover rear vents or install the unit in a closed cabinet or

shelves.

If you install the unit in an enclosure, make sure there is adequate

space at the top of the unit to allow hot air to rise and escape. If the

monitor becomes too hot, the overheat protector will be activated and

the monitor will be turned off. If this happens, turn off the power to the

monitor and unplug the power cord. If the room where the monitor is

installed is particularly hot, move the monitor to a cooler location, and

wait for 60 minutes to cool the monitor. If the problem persists, contact

your dealer for service.

* Display an image with many colors and color gradations (i.e.

photographic or photo-realistic images).

* Create image content with minimal contrast between light and dark

areas, for example white characters on black backgrounds. Use

complementary or pastel color whenever possible.

* Avoid displaying images with few colors and distinct, sharply defined

borders between colors.

Plasma monitor driving sound

2. Do not use this unit’s polarized plug with extension cords or outlets

unless the prongs can be completely inserted.

The panel of the Plasma monitor is composed of extremely fine pixels and

these pixels emit light according to received video signals. This principle

may cause you to hear a buzz or electrical hum coming from the Plasma

monitor.Also note that the rotation speed of the cooling fan motor increases

when the ambient temperature of the Plasma monitor becomes high. You

may hear the sound of the motor at that time.

3. Do not expose the unit to water or moisture.

4. Avoid damage to the power cord, and do not attempt to modify the

power cord.

5. Unplug the power cord during electrical storms or if the unit will

not be used over a long period.

6. Do not open the cabinet which has potentially dangerous high voltage

components inside. If the unit is damaged in this way the warranty will

be void. Moreover, there is a serious risk of electric shock.

7. Do not attempt to service or repair the unit. The manufacturer is not

liable for any bodily harm or damage caused if unqualified persons

attempt service or open the back cover. Refer all service to authorized

Service Centers.

Note:

The following items are not coverd by the warranty.

•

Image retention

Panel generated sound, examples: Fan motor noise, and electrical

circuit humming /glass panel buzzing.

8. This equipment shall be connected to a MAIN outlet with a protective

earth-ground connection.

9. The outlet shall be installed near the equipment and shall be easily

accessible.

Contact your dealer for other recommended procedures that will best

suit your particular application needs.

En-2

NOTE:

WARNING

When you use an RGB cable (not supplied), use an RGB

cable including the ferrite core (not supplied) on both ends

of the cable. If you do not this, this monitor will not

conform to mandatory CE or C-Tick standards.

This product equipped with a three-wire grounding

(earthed) plug - a plug that has a third (grounding)

pin. This plug only fits a grounding-type power

outlet. If you are unable to insert the plug into an

outlet, contact a licensed electrician to replace the

outlet with a properly grounded one. Do not defeat

the safety purpose of the grounding plug.

NOTE:

When you use the power cable (supplied), use the supplied

ferrite cores. Set the ferrite cores (supplied) on both ends

of the power cable (supplied), and then use the bands

(supplied) to fasten the ferrite cores (supplied) to the power

cable (supplied). If you do not this, this monitor will not

conform to mandatory CE or C-Tick standards.

Operating Environment

Operating environment temperature and humidity:

0 °C to +40 °C (+32 °F to +104 °F); less than 80

%RH (cooling vents not blocked)

Do not install this unit in a poorly ventilated area,

or in locations exposed to high humidity or direct

sunlight (or strong artificial light)

Power cable (supplied)

band

core

Disposing of your used

product

EU-wide legislation as implemented in each

Member State requires that used electrical and

electronic products carrying the mark (left) must

be disposed of separately from normal household

waste. This includes plasma monitors and their

electrical accessories. When you dispose of such

products, please follow the guidance of your local

authority and/or ask the shop where you purchased

the product.

NOTE:

When you use a remote cable (not supplied), use the

supplied ferrite core. Wind the remote cable (not supplied)

around the ferrite core (supplied) once, and then fasten

the catch. If you do not this, this monitor will not conform

to mandatory CE or C-Tick standards.

Remote cable (not supplied)

After collecting the used products, they are reused

and recycled in a proper way. This effort will help

us reduce the wastes as well as the negative impact

to the human health and the environment at the

minimum level.

The mark on the electrical and electronic products

only applies to the current European Union Member

States.

To plasma monitor

core

This product complies with the Low Voltage Directive

(73/23/EEC, amended by 93/68/EEC), EMC Directives

(89/336/EEC, amended by 92/31/EEC and 93/68/EEC).

CAUTION

When disposing of used batteries, please comply with

governmental regulations or environmental public

instruction’s rules that apply in your country/area.

En-3

Contents

Contents ...................................................... En-4

Contents of the Package ........................................ En-4

Options .............................................................. En-4

Installation .................................................. En-5

Ventilation Requirements for enclosure mounting ...... En-5

Creating a video wall ........................................... En-6

Cable Management.............................................. En-6

Caution when placing the plasma monitor in portrait mode ..... En-7

Using the remote control ....................................... En-7

Battery Installation and Replacement ..................... En-7

Using the wired remote control mode .................... En-7

Operating Range .................................................... En-7

Part Names and Function .............................. En-8

Front View .......................................................... En-8

Rear View/ Terminal Board ................................... En-9

Remote Control .................................................. En-12

Basic Operations......................................... En-13

POWER ............................................................ En-13

To turn the unit ON and OFF: .............................. En-13

VOLUME .......................................................... En-13

To adjust the sound volume:................................. En-13

MUTE ............................................................... En-13

To mute the audio: ............................................... En-13

DISPLAY ............................................................ En-13

To check the settings: ........................................... En-13

DIGITAL ZOOM ................................................. En-13

AUTO ADJUST .................................................. En-13

To adjust the size or quality of the picture automatically: .. En-13

OFF TIMER ........................................................ En-13

To set the off timer: .............................................. En-13

To check the remaining time: ............................... En-13

To cancel the off timer: ........................................ En-13

WIDE Operations......................................... En-14

Wide Screen Operation (manual) ........................ En-14

When viewing videos or digital video discs ......... En-14

Wide Screen Operation with Computer Signals ..... En-15

When “PICTURE SIZE” is set to “OFF” ............. En-15

SPLIT SCREEN Operations ............................. En-16

Showing a couple of pictures on the screen at the same time .. En-16

Operations in the Side-by-side mode.................... En-16

Operations in the Picture-in-picture mode ............ En-17

Selecting the input signals to be displayed ........... En-17

Zooming in on a specific input ............................. En-17

Adjusting the OSM controls................................. En-17

Option2 Settings Menu ....................................... En-26

Setting the power management for computer images ... En-26

POWER/STANDBY indicator ............................. En-26

Setting the picture to suit the movie ..................... En-26

Reducing image retention .................................... En-26

Setting the gray level for the sides of the screen ... En-28

Setting the screen size for S1/S2 video input ........ En-28

Setting the picture size for RGB input signals ...... En-29

Setting the signal and black level for DVI signal .. En-29

Setting the Protocol set ........................................ En-29

Option3 Settings Menu ....................................... En-29

Using the timer .................................................... En-29

Setting the power on mode................................... En-31

Enabling/disabling the front panel controls .......... En-31

Enabling/disabling remote control wireless

transmission ...................................................... En-32

Loop Out setting .................................................. En-32

Remote ID setting ................................................ En-32

ID number setting ................................................ En-32

Video Wall setting ................................................ En-33

Option4 Settings Menu ....................................... En-35

Removing the sub screen area when there is no input

signal detected for the sub picture...................... En-35

Displaying the entire image during DIGITAL ZOOM

operations .......................................................... En-35

Displaying still images in the sub screen .............. En-35

Switching the input source quickly ...................... En-36

Displaying the information as a text ..................... En-36

Advanced OSM Settings Menu ............................ En-37

Setting the menu mode ........................................ En-37

Language Settings Menu ..................................... En-37

Setting the language for the menus....................... En-37

Color System Settings Menu ................................ En-37

Setting the video signal format ............................. En-37

Source Information Menu .................................... En-37

Checking the frequencies, polarities of input signals,

and resolution .................................................... En-37

Important Information.................................. En-2

External Control ......................................... En-38

Application ....................................................... En-38

Connections ...................................................... En-38

Type of connector: D-Sub 9-pin male .................. En-38

Communication Parameters ................................. En-38

External Control Codes (Reference) ...................... En-38

Pin Assignments ......................................... En-38

mini D-Sub 15-pin connector (Analog) ................. En-38

DVI-D 24-pin connector (Digital) .......................... En-38

1/8 Stereo Mini Jack (not supplied) for

OSM(On Screen Menu) Controls .................... En-18

Menu Operations ............................................... En-18

Menu Tree ......................................................... En-19

Picture Settings Menu.......................................... En-21

Adjusting the picture ............................................ En-21

Setting the picture mode according to the brightness

of the room ........................................................ En-21

Reducing noise in the picture ............................... En-21

Setting the color temperature ............................... En-21

Adjusting the color to the desired level ................ En-22

Changing the Gamma Curve ................................ En-22

Making the Low Tone adjustments ...................... En-22

Adjusting the colors ............................................. En-22

Audio Settings Menu .......................................... En-23

Adjusting the treble, bass and left/right balance and

REMOTE IN/OUT ........................................... En-39

Connection with STB.................................... En-39

Troubleshooting.......................................... En-40

Table of Signals Supported .......................... En-41

Specifications ............................................. En-45

Contents of the Package

Ⅺ Plasma monitor (

Ⅺ Power cord (

1, 3 m/9.8 feet)

Ⅺ Remote control (

ⅪAAABatteries (

2, Manganese battery for remote

control)

audio input select............................................... En-23

Setting the allocation of the audio connectors ...... En-23

Image Adjust Settings Menu ................................ En-23

Adjusting the Position, Size, Fine Picture,

Picture Adj and Underscan ................................ En-23

Option1 Settings Menu ....................................... En-24

Setting the on-screen menu .................................. En-24

Setting the BNC input connector type .................. En-24

Setting the RGB1 connector................................. En-24

Setting a computer image to the correct RGB select

Ⅺ Manuals (Start up Guide and CD-ROM)

Ⅺ Ferrite cores for power cord (

2), bands for power

cord (

Ⅺ Ferrite core for remote cable (

Ⅺ Cable clampers (

3), beads bands (

Options

• Wall mount unit

• Ceiling mount unit

• Tilt mount unit

• Tabletop Stand

• Attachable speakers

screen ................................................................ En-25

Setting high definition images to the suitable screen size .. En-25

Setting the Input Skip........................................... En-25

Resetting to the default values.............................. En-25

En-4

Installation

You can attach your optional mounts or stand to the plasma monitor in one of the following two ways:

* While it is upright. (See Drawing A)

* As it is laid down with the screen face down (See Drawing B). Lay the protective sheet, which was wrapped around the

monitor when it was packaged, beneath the screen surface so as not to scratch the screen face.

* Do not touch or hold the screen face when carrying the unit.

• This device cannot be installed on its own. Be sure to use a stand or original mounting unit. (Wall

mount unit, Stand, etc.)

• For correct installation and mounting it is strongly recommended to use a trained, authorized

dealer.

Failure to follow correct mounting procedures could result in damage to the equipment or injury

to the installer.

Product warranty does not cover damage caused by improper installation.

CAUTION

• Install the device following the installation manual of the optional accessory.

• Install the device in a stable and level environment that is strong enough to support the weight.

• Use the specified clasps for installing.

• After installation, take appropriate measures to prevent the plasma from tipping over or falling.

• Make sure to move or install the device with more than one person(s).

* Use only a mounting kit or stand recommended by the manufacturer and listed as an accessory.

Drawing B

Drawing A

Wall

Ventilation Requirements for

enclosure mounting

To allow heat to disperse, leave space between surrounding

objects as shown on the diagram when installing.

50 mm (2")

Wall

50 mm (2")

En-5

Creating a video wall

With built-in matrix display capability, you can create a (2

2, 3

3, 4

4, 5

5, 5

1, 1

5) video wall.

• Connect signal cables and remote cables as shown below.

Video signal

RGB/DVD/HD signal

Remote

control

Remote

control

RGB signal/

DVD/HD signal

VIDEO Signal

RCA phono plug

BNC connector

VIDEO

AUDIO

DVD1

AUDIO

RGB

DVD2

RGB

AUDIO

RGB

EXTERNAL CONTROL

REMOTE

VIDEO

AUDIO

DVD

HD1

AUDIO

RGB2

DVD2

RGB

AUDIO

RGB

EXTERNAL CONTROL

REMOTE

(IN/OUT)

R/Cr/Pr

G/Y

B/Cb/Pb

Cb/Pb Cr/Pr

(IN/OUT)

DVI

(Digital RGB)

OUT

(IN/OUT)

R/Cr/Pr

G/Y

B/Cb/Pb

(Digital RGB)

Cb/Pb Cr/Pr

(IN/OUT)

DVI

OUT

L ₍

(

MONO

)

MONO

)

(

MONO

)

L ₍

(

MONO

)

MONO

)

(

MONO

)

BNC connector

OUT

VIDEO Signal

OUT

Remote

control

OUT

Remote

control

RGB signal/

DVD/HD signal

Note:

1. The VIDEO1 and RGB1 terminals can be used for either INPUT or OUTPUT.

When LOOP OUT is ON, do not connect an OUTPUT signal from another unit as it may damage the other unit due to an

extraordinary load.

2. LOOP OUT can not be turned ON while signals are input to the RGB1 terminal.

3. LOOP OUT can be turned ON while signals are input to the RGB1 terminal if the POWER is switched ON.

Information

• To loop signals out to another plasma display, set the LOOP OUT to ON.

• To create a video wall, set the VIDEO WALL menu items properly.

• To connect monitors, please use a 1 m to 2 m (3.3 feet to 6.6 feet) BNC cable (any commercially available cable).

• If the image quality is poor, do not use the monitor’s out terminal. Use a distribution amplifier (any commercially

available distribution amplifier) to connect the split signals to the respective monitor INPUT terminals.

• Being used as a video wall function, maximaly 4-screen is rough-standard with lower than 1024

768, 60 Hz

signal.

• A distribution amplifier is particularly recommended when creating a 3

3 (or greater) video wall.

• When looping from plasma to plasma, a 1 m to 2 m (3.3 feet to 6.6 feet) 15 pin male D-Sub - 5BNC conversion

cable is required.

Cable Management

Using the cable clampers and beads bands provided with the plasma display; Bundle the signal and audio cables at the

back of the unit to connect to the display.

42XM5

50XM6

60XM5

Back of the unit

mounting holes

To attach

Bunch separated cables together and To detach

Insert q into a mounting hole, then secure them with the provided beads Using pliers, twist the clamper 90° and

snap w into the back of q to fix the bands. pull it outward. In some cases the

clamper. Do not allow excessive stress to be clamper may have deteriorated over

Clampers are designed to be difficult placed on the ends of cables.

to undo once in place. Please attach

carefully. Cables can be routed to the

right or left.

time and may get damaged when

removed.

En-6

Top side

Caution when placing the plasma monitor in portrait mode

• Use the optional mount. Contact your store to purchase before installing.

OPTION1

OSM

BNC INPUT

RGB

D-SUB INPUT

• Rotate 90° clockwise as seen from the front when installing.

RGB

RGB SELECT

90°

AUTO

HD SELECT

1080B

INPUT SKIP

• After installing, make sure the NEC logo is located at the

left hand side of the screen when facing the plasma from

the front.

OFF

ALL RESET

OFF

1024

768

SEL.

MENU/ENTER

EXIT RETURN

• Be sure to set “OSM ANGLE” to “V” when using.

* Failure to heed the above cautions may lead to malfunction.

Using the remote control

Battery Installation and Replacement

VOLUME

DOWN

INPUTSELECT

EXIT

MENU/ENTER

LEFT/

RIGHT/

Designated batteries:

Bottom side

Please use size AAA (R03) or AAA (LR03).

Insert the 2 “AAA” batteries, making sure to set them in

with the proper polarity.

Operating Range

* Use the remote control within a distance of about 7 m/ 23

ft. from the front of the monitor’s remote control sensor

and at horizontal and vertical angles of up to approximately

30°.

1.Press and open the cover.

* The remote control operation may not function if the

monitor’s remote control sensor is exposed to direct

sunlight or strong artificial light, or if there is an obstacle

between the sensor and the remote control.

2.Align the batteries according to the

indication inside the case.

and

Approx.

7 m/23 ft

3.Replace the cover.

Using the wired remote control mode

Connect the remote cable* to the remote control’s remote

jack and the “REMOTE IN” terminal on the monitor.

When the cable is connected, the mode automatically

switches to wired remote control. When the wired remote

control mode is used, the remote control can be operated

even if no batteries are loaded.

CAUTION

• Use only the specified batteries.

• Make sure to insert the batteries correctly according

to the indications of

and

• Do not drop or mishandle the remote control.

• Do not get the remote control wet. If the remote

control gets wet, wipe it dry immediately.

• Avoid heat and humidity.

EXTERNAL CONTROL

REMOTE

OUT

• When not using the remote control for a long period,

remove the batteries.

• Do not use new and old batteries together, or use

different types together.

Remote Control

Cable*

• Do not take apart the batteries, heat them, or throw

them into a fire.

To Remote Jack

• When using the remote control in the wireless

condition, be sure to unplug the remote cable from

the REMOTE IN terminal on the monitor.

En-7

* The 1/8 Stereo Mini cable must be purchased separately.

Part Names and Function

Front View

VOLUME

DOWN

INPUTSELECT

EXIT

MENU/ENTER

LEFT/

RIGHT/

VOLUME

DOWN

INPUTSELECT

/EXIT

MENU/ENTER

LEFT/

RIGHT/

q Power

t LEFT/– and RIGHT/+

Functions as the CURSOR (

ᮤ

ᮣ

Turns the monitor’s power on and off.

) buttons and used

to adjust the picture parameters in the On-Screen Menu

(OSM) mode.

w Remote sensor window

Receives the signals from the remote control.

y VOLUME DOWN and UP

Adjusts the volume.

e POWER/STANDBY indicator

When the power is on ............................. Lights green.

When the power is in the standby mode ... Lights red.

Functions as the CURSOR (L/M) buttons in the On-

Screen Menu (OSM) mode.

r INPUT SELECT / EXIT

Switches the input.

u MENU/ENTER

Sets the On-Screen Menu (OSM) mode and displays

the main menu.

Functions as the EXIT buttons in the On-Screen Menu

(OSM) mode.

WARNING

The Power on/off switch does not completely

disconnect power from the display.

Note:This plasma monitor has the capasity to display images when connected to European DVD players with a SCART

output signal, which is RGB with composite sync.

Your dealer can supply a special SCART cable, which will enable you to use the RGB with composite sync signal.

To obtain the special cable as well as for further information, please contact your dealer.

En-8

Rear View/ Terminal Board

42XM5

VIDEO

AUDIO

L/R

DVD

Cb/Pb Cr/Pr

AUDIO

L/R

RGB

G/Y

DVD

RGB

(IN/OUT)

AUDIO

L/R

RGB

EXTERNAL CONTROL

REMOTE

OUT

R/Cr/Pr

B/Cb/Pb

VIDEO

AUDIO

DVD1

HD1

AUDIO

RGB

DVD

HD2

RGB

AUDIO

RGB

REMOTE

EXTERNAL CONTROL

(IN/OUT)

R/Cr/Pr

G/Y

B/Cb/Pb

Cb/Pb Cr/Pr

(IN/OUT)

DVI

(Digital RGB)

OUT

L ₍

(

MONO

)

MONO

)

(

MONO

)

I J K

A AC IN

H RGB3 (DVI 24pin)

Connect the included power cord here.

Connect a digital signal (TMDS) from a source with a

DVI output.

This input can be set for use with an RGB3.

B EXT SPEAKER L and R

Connect speakers (optional) here. Maintain the correct

polarity. Connect the (positive) speaker wire to the

EXT SPEAKER terminal and the (negative)

speaker wire to the EXT SPEAKER terminal on

EXTERNAL CONTROL

This terminal is used when operating and controlling

the monitor externally with a control system (by RS-

232C).

both LEFT and RIGHT channels.

Please refer to your speaker’s owner’s manual.

J REMOTE IN

C VIDEO1, 2, 3 (BNC, RCA, S-Video)

Connect VCR’s, DVD’s or Video Cameras, etc. here.

VIDEO1 can be used for Input or Output.

Connect the remote cable to the remote control’s

remote jack to obtain wired remote control.

K REMOTE OUT

D AUDIO1, AUDIO2, AUDIO3

These are audio input terminals.

Connect the remote cable to the REMOTE IN jack of

the other display monitor to obtain wired remote

control.

The input is selectable. Set which video image

corresponds to the audio input from the audio menu

screen.

L Handles

Use when installing or carrying the plasma monitor.

E DVD1 / HD1

Connect DVD’s, High Definition or Laser Discs, etc.

here.

Information

• For Y/Cb/Cr, connect to the DVD1 or DVD2

terminals.

F RGB2/ DVD2/ HD2

• For SCART, this unit provides three ways to connect:

· SCART1: Connect R/G/B to the DVD2 terminals

and composite sync. to the HD terminal.

· SCART2: Connect R/G/B to the DVD2 terminals

and composite sync. to the VIDEO1 terminal.

· SCART3: Connect R/G/B + composite sync. to the

RGB1 terminal.

RGB2:

You can connect an analog RGB signal

and the syncronization signal.

DVD2/ HD2: You can connect DVDs, High

Definition sources, Laser Discs, etc.

here.

This input can be set for use with an

RGB or component source.

G RGB1 (mini D-Sub 15pin)

Connect an analog RGB signal from a computer, etc.

here. This input can be used for Input or Output.

En-9

Rear View/ Terminal Board

50XM6

VIDEO

AUDIO

L/R

DVD

Cb/Pb Cr/Pr

AUDIO

L/R

RGB

G/Y

DVD

HD2

RGB

(IN/OUT)

AUDIO

L/R

RGB

EXTERNAL CONTROL

REMOTE

OUT

R/Cr/Pr

B/Cb/Pb

VIDEO

AUDIO

DVD1

AUDIO

RGB2

DVD

RGB

AUDIO

RGB

REMOTE

EXTERNAL CONTROL

(IN/OUT)

R/Cr/Pr

G/Y

B/Cb/Pb

Cb/Pb Cr/Pr

(IN/OUT)

DVI

(Digital RGB)

OUT

L ₍

(

MONO

)

MONO

)

(

MONO

)

I J K

A AC IN

H RGB3 (DVI 24pin)

Connect the included power cord here.

Connect a digital signal (TMDS) from a source with a

DVI output.

This input can be set for use with an RGB3.

B EXT SPEAKER L and R

Connect speakers (optional) here. Maintain the correct

polarity. Connect the (positive) speaker wire to the

EXT SPEAKER terminal and the (negative)

speaker wire to the EXT SPEAKER terminal on

EXTERNAL CONTROL

This terminal is used when operating and controlling

the monitor externally with a control system (by RS-

232C).

both LEFT and RIGHT channels.

Please refer to your speaker’s owner’s manual.

J REMOTE IN

C VIDEO1, 2, 3 (BNC, RCA, S-Video)

Connect VCR’s, DVD’s or Video Cameras, etc. here.

VIDEO1 can be used for Input or Output.

Connect the remote cable to the remote control’s

remote jack to obtain wired remote control.

K REMOTE OUT

D AUDIO1, AUDIO2, AUDIO3

These are audio input terminals.

Connect the remote cable to the REMOTE IN jack of

the other display monitor to obtain wired remote

control.

The input is selectable. Set which video image

corresponds to the audio input from the audio menu

screen.

L Handles

Use when installing or carrying the plasma monitor.

E DVD1 / HD1

Connect DVD’s, High Definition or Laser Discs, etc.

here.

Information

• For Y/Cb/Cr, connect to the DVD1 or DVD2

terminals.

F RGB2/ DVD2/ HD2

• For SCART, this unit provides three ways to connect:

· SCART1: Connect R/G/B to the DVD2 terminals

and composite sync. to the HD terminal.

· SCART2: Connect R/G/B to the DVD2 terminals

and composite sync. to the VIDEO1 terminal.

· SCART3: Connect R/G/B + composite sync. to the

RGB1 terminal.

RGB2:

You can connect an analog RGB signal

and the syncronization signal.

DVD2/ HD2: You can connect DVDs, High

Definition sources, Laser Discs, etc.

here.

This input can be set for use with an

RGB or component source.

G RGB1 (mini D-Sub 15pin)

Connect an analog RGB signal from a computer, etc.

here. This input can be used for Input or Output.

En-10

Rear View/ Terminal Board

60XM5

VIDEO

AUDIO

L/R

DVD

Cb/Pb Cr/Pr

AUDIO

L/R

RGB

G/Y

DVD

HD2

RGB

(IN/OUT)

AUDIO

L/R

RGB

EXTERNAL CONTROL

REMOTE

OUT

R/Cr/Pr

B/Cb/Pb

VIDEO

AUDIO

DVD1

AUDIO

RGB2

DVD

RGB

AUDIO

RGB

REMOTE

EXTERNAL CONTROL

(IN/OUT)

R/Cr/Pr

G/Y

B/Cb/Pb

Cb/Pb Cr/Pr

(IN/OUT)

DVI

(Digital RGB)

OUT

L ₍

(

MONO

)

MONO

)

(

MONO

)

I J K

A AC IN

H RGB3 (DVI 24pin)

Connect the included power cord here.

Connect a digital signal (TMDS) from a source with a

DVI output.

This input can be set for use with an RGB3.

B EXT SPEAKER L and R

Connect speakers (optional) here. Maintain the correct

polarity. Connect the (positive) speaker wire to the

EXT SPEAKER terminal and the (negative)

speaker wire to the EXT SPEAKER terminal on

EXTERNAL CONTROL

This terminal is used when operating and controlling

the monitor externally with a control system (by RS-

232C).

both LEFT and RIGHT channels.

Please refer to your speaker’s owner’s manual.

J REMOTE IN

C VIDEO1, 2, 3 (BNC, RCA, S-Video)

Connect VCR’s, DVD’s or Video Cameras, etc. here.

VIDEO1 can be used for Input or Output.

Connect the remote cable to the remote control’s

remote jack to obtain wired remote control.

K REMOTE OUT

D AUDIO1, AUDIO2, AUDIO3

These are audio input terminals.

Connect the remote cable to the REMOTE IN jack of

the other display monitor to obtain wired remote

control.

The input is selectable. Set which video image

corresponds to the audio input from the audio menu

screen.

L Handles

Use when installing or carrying the plasma monitor.

E DVD1 / HD1

Connect DVD’s, High Definition or Laser Discs, etc.

here.

Information

• For Y/Cb/Cr, connect to the DVD1 or DVD2

terminals.

F RGB2/ DVD2/ HD2

• For SCART, this unit provides three ways to connect:

· SCART1: Connect R/G/B to the DVD2 terminals

and composite sync. to the HD terminal.

· SCART2: Connect R/G/B to the DVD2 terminals

and composite sync. to the VIDEO1 terminal.

· SCART3: Connect R/G/B + composite sync. to the

RGB1 terminal.

RGB2:

You can connect an analog RGB signal

and the syncronization signal.

DVD2/ HD2: You can connect DVDs, High

Definition sources, Laser Discs, etc.

here.

This input can be set for use with an

RGB or component source.

G RGB1 (mini D-Sub 15pin)

Connect an analog RGB signal from a computer, etc.

here. This input can be used for Input or Output.

En-11

u EXIT

Press this button to exit the OSM controls in the main

Remote Control

menu. Press this button during the display of the sub

menu to return to the previous menu.

i POINTER

Press this button to display the pointer.

o ZOOM (+ /–)

Enlarges or reduces the image.

! VOLUME (+ /–)

Adjusts the audio volume.

! MUTE

Mutes the audio.

! WIDE

Press this button to select and switch the screen sizes.

WIDE button is not active for all signals.

! DISPLAY

Displays the source settings on the screen.

! OFF TIMER

Activates the off timer for the unit.

! SIDE BY SIDE

Press this button to show a couple of pictures in the

side-by-side mode.

! PICTURE IN PICTURE

Press this button to show a couple of pictures in the

picture-in-picture mode.

! SINGLE

Cancels the split screen mode.

! SELECT/FREEZE

Press this button to select the active picture in a split

screen mode.

When the PIC FREEZE function is operating, this

button can be used to display still images on the sub

screen.

q POWER ON/STANDBY

Switches the power on/standby.

! AUTO ADJUST

(This does not operate when the POWER/STANDBY

indicator of the plasma is off.)

Press this button to adjust Fine Picture, Picture ADJ,

Position, and Contrast automatically. Press this button

in video mode and theAutoAdjust switches to ZOOM

mode automatically when a letter box image is

displayed.

w RGB/PC

Press this button to select RGB/PC as the source.

RGB/PC can also be selected using the INPUT

SELECT button on the monitor.

@ ID SELECT

e DVD / HD

Set the ID number in the remote control. The remote

control can then be used only for a display with the

same ID number. When several displays are used

together they can be controlled individually.

Press this button to select DVD/HD as the source.

DVD/HD can also be selected using the INPUT

SELECT button on the monitor.

r VIDEO

@ CLEAR/SEAMLESS SW

Press this button to select VIDEO as the source.

Clears the number set by the ID SELECT button.

When the SEAMLESS SW function is operating, this

button can be used to switch the input source quickly.

→ VIDEO1 → VIDEO2 → VIDEO3

VIDEO can also be selected using the INPUT SELECT

button on the monitor.

@ Remote control signal transmitter

Transmits the remote control signals.

t MENU/ENTER

@ Remote Jack

Press this button to access the OSM controls.

Press this button during the display of the main menu

to go to the sub menu.

Insert the plug of the remote cable (The 1/8 Stereo

Mini cable) here when using the supplied remote

control in the wired condition.

ᮤ

ᮣ

y CURSOR (L / M /

)

Use these buttons to select items or settings and to

adjust settings or switch the display patterns.

En-12

Basic Operations

POWER

OFF TIMER

To set the off timer:

To turn the unit ON and OFF:

The off timer can be set to turn the power off after 30, 60,

90 or 120 minutes.

1. Press the OFF TIMER button to start the timer at 30

minutes.

1. Plug the power cord into an active AC power outlet.

2. Press the Power button (on the unit).

The monitor’s POWER/STANDBY indicator turns red

and the standby mode is set.

2. Press the OFF TIMER button to the desired time.

3. The timer starts when the menu turns off.

→ 30 → 60 → 90 → 120 → 0

3. Press the POWER ON button (on the remote control) to

turn on the unit.

The monitor’s POWER/STANDBY indicator will light

up (green) when the unit is on.

4. Press the POWER STANDBYbutton (on the remote control)

or the Power button (on the unit) to turn off the unit.

The monitor’s POWER/STANDBY indicator turns red

and the standby mode is set (only when turning off the

unit with the remote control).

OFF TIMER 30

VOLUME

To adjust the sound volume:

1. Press and hold the VOLUME

control or the unit) to increase to the desired level.

2. Press and hold the VOLUME

button (on the remote

To check the remaining time:

1. Once the off timer has been set, press the OFF TIMER

button once.

button (on the remote

control or the unit) to decrease to the desired level.

2. The remaining time is displayed, then turns off after a few

seconds.

3. When five minutes remain the remaining time appears

until it reaches zero.

MUTE

To mute the audio:

Press the MUTE button on the remote control to mute the

audio; press again to restore.

OFF TIMER 28

DISPLAY

To check the settings:

1. Press the DISPLAY button to display the display mode.

2. If the button is not pressed for approximately three seconds,

the menu turns off.

DIGITAL ZOOM

To cancel the off timer:

1. Press the OFF TIMER button twice in a row.

2. The off timer is canceled.

Digital zoom specifies the picture position and enlarges

the picture.

1. (Be sure ZOOM NAV is off.)

OFF TIMER

Press the POINTER button to display the pointer. (

)

To change the size of the picture:

Press the ZOOM+ button and enlarge the picture.

The pointer will change to resemble a magnifying glass.

(

)

A press of the ZOOM- button will reduce the picture

and return it to its original size.

To change the picture position:

Select the position with the LM

Note:

ᮤ ᮣ

buttons.

After the power is turned off with the off timer ...

2. Press the POINTER button to delete the pointer.

A slight current is still supplied to the monitor. When you

are leaving the room or do not plan to use the system for a

long period of time, turn off the power to the monitor.

AUTO ADJUST

To adjust the size or quality of the picture

automatically:

Press the AUTO ADJUST button.

Information

Ⅵ AUTO ADJUST ON setting

When RGB (still picture) input is selected:

Fine Picture, Picture ADJ, Position, and Contrast will

be adjusted automatically.

When RGB (motion picture), VIDEO, or Y/Pb/Pr

(component) input is selected:

The screen size switches to ZOOM mode automatically

when a letter box image is displayed.

En-13

WIDE Operations

2.35:1 size screen

Wide Screen Operation (manual)

With this function, you can select one of seven screen sizes.

When viewing videos or digital video discs

1. Press the WIDE button on the remote control.

2. Within 3 seconds ...

Original image

Press the WIDE button again.

Information is lost on both sides.

The screen size switches as follows:

The squeezed film image is expanded to fulfill the entire

screen at a ratio of 2.35:1. Black bands do not appear at

the top and bottom but information is lost on the left and

right margins.

• This feature is available when the input signal is video,

component (480I, 480P, 576I, 576P, 720P, 1080I) or RGB

(525P or 625P signal from a scan converter).

* If black bands appear on the top and bottom in the full size

screen, select the 2.35:1 size screen to fill the screen and

avoid image retention.

→ NORMAL → FULL → STADIUM → ZOOM → 2.35:1 → 14:9 → UNDERSCAN

When a 720P or 1080I signal is input:

FULL ↔ 2.35:1

When displaying enhanced split screen:

NORMAL ↔ FULL

NORMAL size screen (4:3)

14:9 size screen

The normal size screen is displayed.

* The picture has the same size as video pictures with a 4 : 3

aspect ratio.

The image is displayed at a 14:9 aspect ratio.

* This feature is available when the input signal is video,

component (480I, 480P, 576I, 576P) or RGB (525Por 625P

signal from a scan converter).

FULL size screen

UNDERSCAN size screen

Set “UNDERSCAN” to “ON” in the “IMAGE ADJUST”.

Typical televisions crop the image (i.e., overscan). In order

to restore the entire image, select UNDERSCAN.

The image is expanded in the horizontal direction.

* Images compressed in the horizontal direction (“squeezed

images”) are expanded in the horizontal direction and

displayed on the entire screen with correct linearity.

(Normal images are expanded in the horizontal direction.)

STADIUM size screen

Overscan

Underscan

* Picture noise or black border may appear near the edge of

screen depending on the connected component.

* The continuous display in this screen size over a prolonged

period of time may result in image retention.

* When Macrovision signal is input, the brightness may

change.

The picture is expanded in the horizontal and vertical

directions at different ratios.

* Use this for watching normal video programs (4:3) with a

wide screen.

Note:

Do not allow 4:3 content to be displayed for extended

periods of time without using gray bars. This can cause

image retention.

ZOOM size screen

The picture is expanded in the horizontal and vertical

direction, maintaining the original proportions.

* Use this for theater size (wide) movies, etc.

En-14

FULL size screen

Wide Screen Operation with

Computer Signals

Switch to the wide screen mode to expand the 4 : 3 image

to fill the entire screen.

1.Press the WIDE button on the remote control.

2.Within 3 seconds ...

The image is expanded in the horizontal and vertical

direction.

Press the WIDE button again.

The screen size switches as follows:

→ NORMAL → FULL → ZOOM

ZOOM size screen

When displaying enhanced split screen:

NORMAL ↔ FULL

NORMAL size screen (4:3 or SXGA 5:4)

When wide signals are input.

TRUE

The picture has the same size as the normal computer image.

FULL size screen

The image is true resolution.

FULL

The image is expanded in the horizontal direction.

ZOOM size screen

Information

Ⅵ Supported resolution

When wide signals are input.

See page En-41 for details on the display output of the

various VESA signal standards supported by the

monitor.

FULL size screen

Ⅵ “PICTURE SIZE” setting

When the setting of “PICTURE SIZE” is OFF, the size

of RGB-input pictures will be TRUE in place of

NORMAL.

Ⅵ When 852 (848) dot

480 line wide VGA*

signals with a vertical frequency of 60 Hz and

horizontal frequency of 31.7 (31.0) kHz are

input

Select an appropriate setting for RGB SELECT mode

referring to the“Table of Signals Supported” on page

En-41.

When “PICTURE SIZE” is set to “OFF”

* This cannot be set in some models. “TRUE” size will not

be displayed in such cases.

The screen size switches as follows:

→ TRUE → FULL → ZOOM

* “VGA”, “SVGA” and “SXGA” are registered

trademarks of IBM, Inc. of the United States.

TRUE size screen (VGA, SVGA 4:3)

Note:

Do not allow 4:3 content to be displayed for extended

periods of time without using gray bars. This can cause

image retention.

The image is true resolution.

En-15

SPLIT SCREEN Operations

Operations in the Side-by-side mode

Showing a couple of pictures on the

ᮤ ᮣ

ᮢ

screen at the same time

* There may be some RGB-input signals that may not be

displayed as not all signals are supported.

To change the picture size, press the cursor

button.

ᮤ

button

VIDEO1

RGB2

VIDEO1

RGB2

VIDEO1

RGB2

1. Press the button to select a screen mode from among single

mode, side-by-side, and picture-in-picture.

ᮣ

button

Side-by-Side2-R

Side-by-Side1

Side-by-Side2-L

VIDEO1

ᮢ

button

ᮤ

SINGLE

button

VIDEO1

RGB2

VIDEO1

RGB2

VIDEO1

RGB2

SINGLE

button

ᮣ

PICTURE IN PICTURE

button

SIDE BY SIDE

button

Side-by-Side4-R

Side-by-Side3

Side-by-Side4-L

To swap the picture on the right and the left, press the

SIDE BY SIDE

button

ꢀ

cursor button.

VIDEO1

RGB1

VIDEO1

RGB1

Main screen

VIDEO1

RGB1

Sub

screen

PICTURE IN

PICTURE

button

Note:

Picture A and B on the above screen are not always of the

same height.

ꢀ

button

RGB1

VIDEO1

Information

Split screen operations may not function depending on

the combination of input signals. In the table below,

“ࠗ” means Yes, “

” means No.

To make the desired picture active, press the SELECT/

FREEZE button.

Pictures displayed on the right/main screen (Select1)

VIDEO1 VIDEO2 VIDEO3 DVD/HD1 DVD/HD2 SCART1 SCART2 SCART3 RGB1 RGB2 RGB3

Pictures

displayed on

the left/sub

screen

VIDEO1

VIDEO2

VIDEO3

DVD/HD1

DVD/HD2

SCART1

SCART2

SCART3

RGB1

ࠗ

VIDEO1

RGB1

(Select2)

RGB2

RGB3

Ⅵ Split screen operations may not function

depending on the frequency of the RGB

signals.

SELECT/FREEZE

button

VIDEO1

RGB1

En-16

Operations in the Picture-in-picture mode

Selecting the input signals to be displayed

1. Press the SELECT/FREEZE button to make the desired

picture active.

2. Press the RGB/PC, VIDEO, or DVD/HD button.

Each press of the button changes the selection of the input

signal.

ᮤ

To move the position of the sub screen, press the cursor

ᮣ

or button.

ᮣ

VIDEO1

RGB2

VIDEO1

RGB2

button

The INPUT SELECT button on the monitor can also be

used to change the selection.

ᮤ

button

Top Right

Top Left

ᮣ

ᮤ

ᮣ

Zooming in on a specific input

1. Press the SELECT/FREEZE button to make the desired

picture active.

button

ᮤ

button

VIDEO1

RGB2

VIDEO1

RGB2

2. Use the POINTER button and the ZOOM

button to

enlage the picture.

ᮣ

button

For details, see “DIGITAL ZOOM” on page En-13.

Bottom Left

Bottom Right

Adjusting the OSM controls

1. Press the SELECT/FREEZE button to make the desired

picture active.

ᮢ

To change the size of the sub screen, press the button.

VIDEO1

RGB1

2. Press the MENU/ENTER button to display the MAIN

MENU.

3. Adjust the setting to your preference.

For details, see “OSM (On Screen Menu) Controls” on

page En-18.

VIDEO1

RGB1

ᮢ button

VIDEO1

RGB1

Note:

During enhanced split screen, some functions of OSM

controls are not available.

ᮢ button

VIDEO1

RGB1

ᮢ button

To make the desired picture active, press the SELECT/

FREEZE button.

VIDEO1

RGB1

VIDEO1

RGB1

SELECT/

FREEZE

button

En-17

OSM(On Screen Menu) Controls

Menu Operations

The OSM window is displayed with respect to the

screen as shown on the diagram.

Note:The main menu disappears by pressing the EXIT

button.

Information

Ⅵ Advanced menu mode

* Depending on the screen’s mode, the OSM may be

displayed differently.

In the explanation, the OSM section is shown close up.

When “ADVANCED OSM” is set to “ON” in the main

menu (1/2), full menu items will be shown.

MAIN MENU

PICTURE

AUDIO

IMAGE ADJUST

OPTION 1

MAIN MENU

1 / 2

PICTURE

AUDIO

ADVANCED OSM

OFF

SEL.

MENU/ENTER OK

EXIT EXIT

IMAGE ADJUST

OPTION 1

OPTION 2

OPTION 3

OPTION 4

ADVANCED OSM

MENU/ENTER

EXIT

SEL.

The following describes how to use the menus and the

selected items.

1. Press the MENU/ENTER button on the remote control to

display the MAIN MENU.

* The actual screen may be different from the ones in

this manual.

MAIN MENU

1 / 2

PICTURE

AUDIO

IMAGE ADJUST

OPTION 1

ADVANCED OSM

OFF

MENU/ENTER

EXIT

SEL.

MAIN MENU

LANGUAGE

COLOR SYSTEM

SOURCE INFORMATION

2 / 2

MENU/ENTER

EXIT

SEL.

2. Press the cursor buttons ꢀ M on the remote control to

highlight the menu you wish to enter.

3. Press the MENU/ENTER button on the remote control to

select a sub menu or item.

PICTURE

1 / 2

: 52

: 32

: 16

: 32

CONTRAST

BRIGHTNESS

SHARPNESS

COLOR

TINT

PICTURE MODE

NORMAL

OFF

EXIT

RETURN

SEL.

ADJ.

4. Adjust the level or change the setting of the selected item

ᮤ ᮣ

by using the cursor buttons

on the remote control.

5. The adjustments or settings are then stored in memory.

The change is stored until another change is made.

6. Repeat steps 2 – 5 to adjust an additional item, or press

the EXIT button on the remote control to return to the

main menu.

* When adjusting using the bar at the bottom of the screen,

ᮤ

ᮣ

press the or button within 5 seconds. If not, the

current setting is stored and the previous screen appears.

En-18

Menu Tree

:Shaded areas indicate the default value.

ᮤ

ᮣ

←→

: Press the or button to adjust.

:Menu items in a ruled box are available when the ADVANCED OSM is set to ON.

Main menu

Sub menu

Sub menu 2

Sub menu 3

Sub menu 4

RESET

OSM ANGLE “V” REFERENCE

PICTURE

CONTRAST

BRIGHTNESS

SHARPNESS

COLOR

TINT

PICTURE MODE

←→

0←52→72

←→

0←32→64

←→

0←16→32

←→

0←32→64

R←→G 0←32→64

BRIGHT/NORMAL/THEAT.1/THEAT.2/DEFAULT

OFF/NR-1/NR-2/NR-3

LOW/MID LOW/MID/HIGH

YES

En-21

En-22

COLOR TEMP.

WHITE BALANCE

GAIN RED

GAIN GREEN

GAIN BLUE

BIAS RED

BIAS GREEN

BIAS BLUE

RESET

←→

0←40→70

←→

0←40→70

←→

0←40→70

←→

0←40→70

←→

0←40→70

←→

0←40→70

OFF←→ON

…

GAMMA

LOW TONE *⁴

COLOR TUNE

1←→2← →4

MODE1←→MODE2

RED

GREEN

Y←→M 0←32→64

C←→Y 0←32→64

M←→C 0←32→64

G←→R 0←32→64

R←→B 0←32→64

B←→G 0←32→64

OFF←→ON

BLUE

YELLOW

MAGENTA

CYAN

RESET

Main menu

Sub menu

Sub menu 2

Sub menu 3

Sub menu 4

RESET

OSM ANGLE “V” REFERENCE

AUDIO

BASS

TREBLE

BALANCE

AUDIO INPUT1

AUDIO INPUT2

AUDIO INPUT3

←→

0←13→26

←→

0←13→26

L←→R -22←0→+22

VIDEO 1-3 / DVD/HD 1-2 / RGB 1-3

YES

En-23

Main menu

Sub menu

Sub menu 2

Sub menu 3

Sub menu 4

RESET

OSM ANGLE “V” REFERENCE

IMAGE ADJUST

ASPECT MODE

V-POSITION

H-POSITION

V-HEIGHT

NORMAL/FULL/STADIUM/ZOOM/2.35:1/14:9/UNDERSCAN/TRUE*³

←→

-64←0→+64

←→

-128←0→+127

←→

0←→64

—

YES

En-23

YES

H-WIDTH

←→

0←→64

AUTO PICTURE

FINE PICTURE*¹

PICTURE ADJ.*¹

UNDERSCAN

OFF←→ON*²

←→

*²0←→64

←→

*²0←→64

OFF←→ON

Main menu

Sub menu

Sub menu 2

Sub menu 3

Sub menu 4

RESET

OSM ANGLE “V” REFERENCE

OPTION1

OSM

DISPLAY OSM

OSM ADJ.

OSM ANGLE

OSM ORBITER

OFF←→ON

1← →6

H←→V

OFF←→ON

YES

—

YES

—

YES

En-24

En-25

…

OSM CONTRAST LOW←→NORMAL

BNC INPUT

D-SUB INPUT

RGB SELECT

HD SELECT

INPUT SKIP

ALL RESET

RGB←→COMP.←→SCART1←→SCART2

RGB←→SCART3

AUTO

1080B/1035I/1080A

OFF←→ON

En-19

Main menu

Sub menu

Sub menu 2

Sub menu 3

Sub menu 4

RESET

OSM ANGLE “V” REFERENCE

OPTION2

PWR. MGT.

CINEMA MODE

LONG LIFE

OFF←→ON

PLE

YES

En-26

En-27

En-28

En-29

AUTO/LOCK 1/LOCK 2/LOCK 3

AUTO 1

AUTO 2

ORBITER

MANUAL

OFF

H-DOT/V-LINE/TIME

INVERSE

OFF

WORKING TIME/WAITING TIME

WHITE

SCREEN WIPER OFF

WORKING TIME/WAITING TIME/SPEED

SOFT FOCUS

OFF/1/2/3/4

…

GRAY LEVEL

S1/S2

PICTURE SIZE*³

DVI SET UP

0← →3← →15

AUTO←→OFF

OFF←→ON

PLUG/PLAY

BLACK LEVEL

OFF←→ON

PC←→STB/DVD

LOW←→HIGH

YES

PROTOCOL SET

Main menu

Sub menu

Sub menu 2

Sub menu 3

Sub menu 4

RESET

OSM ANGLE “V” REFERENCE

OPTION3

TIMER

PRESENT TIME

SUMMER TIME

DAY/HOUR/MINUTES

OFF

OFF←→ON

En-29

En-30

En-31

En-32

En-33

En-34

TIMER

YES

—

YES

PROGRAM

REPEAT

LAST /MULTI/ VIDEO 1-3 / DVD/HD 1-3 / RGB 1-3

DAY/ON/OFF(HOUR, MINUTES)/INPUT/FUNC.

SINGLE/MULTI/VIDEO-W

PWR. ON MODE

INPUT

VOLUME

…

LAST←→0← →42

CONTROL LOCK

IR REMOTE

LOOP OUT

REMOTE ID

ID NUMBER

VIDEO WALL

OFF←→ON

ALL←→1← →4

ALL←→1← →256

…

DIVIDER

OFF/1/2

2/3

3/4

4/5

5/5

1/1

…

POSITION

DISP. MODE

AUTO ID

No.1← →No.4/No.7← →No.15/No.16← →No.31/No.32← →No.56

SPLIT←→BLANK

OFF←→ON

IMAGE ADJUST ASPECT MODE

NORMAL/FULL/STADIUM/ZOOM/2.35:1/14:9/UNDERSCAN/TRUE

—

V-POSITION/H-POSITION/V-HEIGHT/H-WIDTH/AUTO PICTURE/

FINE PICTURE*¹/PICTURE ADJ.*¹/UNDERSCAN

OFF/ON/MODE1/MODE2

P. ON DELAY

PLE LINK

YES

En-34

OFF←→ON

Main menu

Sub menu

Sub menu 2

Sub menu 3

Sub menu 4

RESET

OSM ANGLE “V” REFERENCE

OPTION4

SUB. PICTURE

SUB. P DETECT OFF←→AUTO

YES

En-35

En-36

…

SUB. P RATE

20%← →100%

DISPLAY

FADE←→NORMAL

ZOOM NAV

PIC FREEZE

SEAMLESS SW

OFF←→S BY S←→BTM LFT←→BTM RGT←→TOP RGT←→TOP LFT

OFF←→S BY S1←→S BY S2←→BTM LFT←→BTM RGT←→TOP RGT←→TOP LFT

OFF

SELECT1/SELECT2

TEXT INSERT

OFF/BOTTOM-1/BOTTOM-2/BOTTOM-3/MID. LOW/MID. HIGH/TOP-3/TOP-2/TOP-1/LEFT/RIGHT YES

INPUT/SUB. P DETECT/PIC. RATE/DISPLAY

YES

Main menu

Sub menu

Sub menu 2

Sub menu 3 Sub menu 4

RESET

OSM ANGLE “V” REFERENCE

ADVANCED OSM OFF←→ON

LANGUAGE ENGLISH/DEUTSCH/FRANÇAIS/ESPAÑOL/ITALIANO/SVENSKA/ꢀУꢁꢁꢂꢃꢄ/EΛΛHNIKA/PORTUGUÊS/TÜRKÇE

COLOR SYSTEM AUTO/3.58 NTSC/4.43 NTSC/PAL/PAL 60/PAL-N/PAL-M/SECAM

YES

—

YES

En-37

SOURCE INFORMATION

—

*1 Only when AUTO PICTURE is OFF.

*2 RGB only.

*3 “PICTURE SIZE” and “TRUE” are only for 50 and 60 inch types.

*4 “LOW TONE” is only for 50 inch type.

Information

Ⅵ Restoring the factory default settings

Select “ALL RESET” under the OPTION1 menu. Note that this also restores other settings to the factory defaults.

En-20

Picture Settings Menu

Information

Adjusting the picture

The contrast, brightness, sharpness, color and tint can be

adjusted as desired.

Ⅵ Types of picture modes

THEAT. 1, 2: Set this mode when watching video in a

dark room.

Example: Adjusting the contrast

This mode provides darker, finer pictures, like the

screen in movie theaters.

For a darker image, select THEAT. 2.

NORMAL: Set this mode when watching video in a

bright room.

BRIGHT: This mode provides brighter pictures than

NORMAL.

This mode provides dynamic pictures with distinct

differences between light and dark sections.

DEFAULT: Use this to reset the picture to the factory

default settings.

On “CONTRAST” of “PICTURE” menu, adjust the contrast.

PICTURE

1 / 2

CONTRAST

BRIGHTNESS

SHARPNESS

COLOR

TINT

PICTURE MODE

NORMAL

OFF

SEL.

ADJ.

EXIT RETURN

CONTRAST

Note:If “CAN NOT ADJUST” appears ...

When trying to enter the PICTURE submenu, make sure

PICTURE MODE is not set to DEFAULT.

Reducing noise in the picture

Use these settings if the picture has noise due to poor

reception or when playing video tapes on which the picture

quality is poor.

Information

Ⅵ Picture adjustment screen

CONTRAST: Changes the picture’s white level.

BRIGHTNESS: Changes the picture’s black level.

SHARPNESS: Changes the picture’s sharpness.

Adjusts picture detail of VIDEO display.

COLOR: Changes the color density.

TINT: Changes the picture’s tint. Adjust for natural

colored skin, background, etc.

Ⅵ Adjusting the computer image

Only the contrast and brightness can be adjusted when

a computer signal is connected.

Example: Setting “NR-3”

On “NR” of “PICTURE” menu, select “NR-3”.

PICTURE

1 / 2

CONTRAST

BRIGHTNESS

SHARPNESS

COLOR

TINT

PICTURE MODE

NORMAL

OFF

SEL.

ADJ.

EXIT RETURN

NR-3

Information

Ⅵ NR

* “NR” stands for Noise Reduction.

* This function reduces noise in the picture.

Ⅵ Restoring the factory default settings

Select “DEFAULT” under the “PICTURE MODE”

settings.

Ⅵ Types of noise reduction

There are three types of noise reduction. Each has a

different level of noise reduction.

The effect becomes stronger as the number increases

(in the order NR-1 → NR-2 → NR-3).

OFF: Turns the noise reduction function off.

Setting the picture mode according to the

brightness of the room

There are four picture modes that can be used effectively

according to the environment in which you are viewing

the display.

Example: Setting the “THEAT. 1” mode

On “PICTURE MODE” of “PICTURE” menu, select

“THEAT. 1”.

Setting the color temperature

Use this procedure to set color tone produced by the plasma

display.

PICTURE

1 / 2

CONTRAST

BRIGHTNESS

SHARPNESS

COLOR

Example: Setting “HIGH”

TINT

On “COLOR TEMP.” of “PICTURE” menu, select “HIGH”.

PICTURE MODE

NORMAL

OFF

PICTURE

2 / 2

SEL.

ADJ.

EXIT RETURN

PICTURE MODE

THEAT.

COLOR TEMP.

GAMMA

LOW TONE

COLOR TUNE

HIGH

MODE1

EXIT

RETURN

SEL.

ADJ.

Information

Ⅵ Setting the color temperature

LOW: More red

MID LOW: Slightly red

MID: Standard (slightly bluer)

HIGH: More blue

En-21

Adjusting the color to the desired level

Use this procedure to adjust the white balance for each

color temperature to achieve the desired color quality.

Making the Low Tone adjustments

You can select the tone reproduction from 2 modes.

This function is effective especially for dark images.

* This function is available only for 50 inch type.

Example: Adjusting the “GAIN RED” of “HIGH” color

temperature

Example: Setting “MODE2”

Set “ADVANCED OSM” to “ON” in the MAIN MENU.

On “LOW TONE” of “PICTURE” menu, select “MODE2”.

On “COLORTEMP.” of “PICTURE” menu, select “HIGH”,

then press the MENU/ENTER button.

The “WHITE BALANCE” screen appears.

PICTURE

2 / 2

COLOR TEMP.

GAMMA

LOW TONE

COLOR TUNE

MID

MODE2

On “GAIN RED”, adjust the white balance.

WHITE BALANCE

COLOR TEMP. HIGH

GAIN RED

GAIN GREEN

GAIN BLUE

BIAS RED

BIAS GREEN

BIAS BLUE

RESET

EXIT

RETURN

SEL.

ADJ.

OFF

Adjusting the colors

SEL.

ADJ.

EXIT RETURN

GAIN RED

Use this procedure to adjust hue and color density for red,

green, blue, yellow, magenta and cyan without changing

the white point.

You can accentuate the green color of trees, the blue of

the sky, etc.

Information

Ⅵ Adjusting the white balance

GAIN R/G/B:White balance adjustment for white level.

BIAS R/G/B:White balance adjustment for black level.

RESET: Resets settings to the factory default values.

Example: Adjusting the color tune for blue

ᮤ

ᮣ

Set “ADVANCED OSM” to “ON” in the MAIN MENU.

Use

and buttons to select “ON”, then press the

MENU/ENTER button.

Ⅵ Restoring the factory default settings

Select “RESET” under the WHITE BALANCE menu.

On “PICTURE” menu, select “COLOR TUNE”, then press

the MENU/ENTER button.

The “COLOR TUNE” screen appears.

On “BLUE” of “COLOR TUNE”, adjust the color tune.

Changing the Gamma Curve

This feature adjusts the brightness of the midtone areas

while keeping shadows and highlights unchanged.

COLOR TUNE

RED

GREEN

BLUE

YELLOW

MAGENTA

CYAN

: 32

Example: Setting “3”

Set “ADVANCED OSM” to “ON” in the MAIN MENU.

On “GAMMA” of “PICTURE” menu, select “3”.

RESET

OFF

EXIT

RETURN

SEL.

ADJ.

PICTURE

2 / 2

Information

Ⅵ COLOR TUNE settings

RED: Adjusts hue of Red

COLOR TEMP.

GAMMA

MID

MODE1

LOW TONE

COLOR TUNE

GREEN: Adjusts hue of Green

BLUE: Adjusts hue of Blue

EXIT

RETURN

SEL.

ADJ.

YELLOW: Adjusts hue of Yellow

MAGENTA: Adjusts hue of Magenta

CYAN: Adjusts hue of Cyan

Information

Ⅵ GAMMA settings

RESET: Resets settings to the factory default value.

The picture becomes darker as the number increases

(in the sequence of 1, 2, 3, 4).

ᮤ

ᮣ

Use

and buttons to select “ON”, then press the

MENU/ENTER button.

En-22

IMAGE ADJUST

Audio Settings Menu

ASPECT MODE

NORMAL

V-POSITION

H-POSITION

V-HEIGHT

Adjusting the treble, bass and left/right

balance and audio input select

The treble, bass and left/right balance can be adjusted to

suit your tastes.

H-WIDTH

AUTO PICTURE

FINE PICTURE

PICTURE ADJ.

UNDERSCAN

OFF

V-POSITION

SEL.

ADJ.

EXIT RETURN

Example: Adjusting the bass

On “BASS” of “AUDIO” menu, adjust the bass.

AUDIO

Information

Ⅵ When “AUTO PICTURE” is “OFF”

BASS

TREBLE

: 26

: 13

IMAGE ADJUST

ASPECT MODE

V-POSITION

H-POSITION

V-HEIGHT

FULL

BALANCE

AUDIO INPUT 1

AUDIO INPUT 2

AUDIO INPUT 3

VIDEO1

DVD/HD1

RGB1

: 32

H-WIDTH

AUTO PICTURE

FINE PICTURE

PICTURE ADJ.

UNDERSCAN

OFF

: 32

EXIT

RETURN

SEL.

ADJ.

EXIT

RETURN

SEL.

ADJ.

Note :If “CAN NOT ADJUST” appears...

Set “AUDIO INPUT” on the AUDIO menu correctly.

When Auto Picture is off, the Fine Picture and the

Picture ADJ. items are displayed so that you can adjust

them.

Ⅵ Adjusting the Auto Picture

Information

ON: The Picture ADJ., Fine Picture and Position

adjustments are made automatically.

Not available for digital ZOOM.

OFF: The Picture ADJ., Fine Picture and Position

adjustments are made manually.

Ⅵ Audio settings menu

BASS: Controls the level of low frequency sound.

TREBLE: Controls the level of high frequency sound.

BALANCE: Controls the balance of the left and right

channels.

* If FINE PICTURE can’t be adjusted, set Auto Picture

to OFF and adjust manually.

Ⅵ Adjusting the position of the image

V-POSITION: Adjusts the vertical position of the

image.

Setting the allocation of the audio connectors

Setting the AUDIO 1, 2, and 3 connectors to the desired

input.

Example: Setting “AUDIO INPUT1” to “VIDEO2”

On “AUDIO INPUT1” of “AUDIO” menu, select

“VIDEO2”.

H-POSITION: Adjusts the horizontal position of the

image.

V-HEIGHT: Adjusts the vertical size of the image.

(Not available for STADIUM mode)

H-WIDTH: Adjusts the horizontal size of the image.

(Not available for STADIUM mode)

FINE PICTURE*: Adjusts for flickering.

PICTURE ADJ.*: Adjusts for striped patterns on the

image (i.e. vertical banding).

The available sources depend on the settings of input.

AUDIO

BASS

TREBLE

BALANCE

AUDIO INPUT 1

AUDIO INPUT 2

AUDIO INPUT 3

: 13

VIDEO2

DVD/HD1

RGB1

EXIT

RETURN

SEL.

ADJ.

* The PictureADJ. and Fine Picture features are available

only when the “Auto Picture” is off.

Information

Ⅵ AUDIO INPUT

A single audio input cannot be selected as the audio

channel for more than one input terminal.

* TheAUTO PICTURE, FINE PICTURE and PICTURE

ADJ. are available only for RGB signals.

But, these features are not available for moving pictures

on VIDEO, DVD/HD or RGB.

Ⅵ Setting the Underscan

Set “ADVANCED OSM” to “ON” in the MAIN MENU.

ON: UNDERSCAN can be selected in ASPECT

MODE.

OFF: UNDERSCAN cannot be selected in ASPECT

MODE.

Image Adjust Settings Menu

Adjusting the Position, Size, Fine Picture,

Picture Adj and Underscan

The position of the image can be adjusted and flickering

of the image can be corrected.

* Selectable only when video signal is input.

Example:Adjusting the vertical position in the normal

mode

On “V-POSITION” of “IMAGEADJUST” menu, adjust the

position.

ᮤ

ᮣ

The mode switches as follows each time the or button is

pressed:

NORMAL ↔ FULL

* The mode can also be switched by pressing the WIDE

button on the remote control.

* The settings on the IMAGE ADJUST menu are not preset

at the factory.

En-23

Setting the BNC input connector type

Select whether to set the input of the 5 BNC connectors to

RGB, Component or SCART1,2.

Option1 Settings Menu

Setting the on-screen menu

This sets the position of the menu, the display format

(horizontal or vertical) etc.

Example: Set the “BNC INPUT” mode to “COMP.”

Example: Turning the DISPLAY OSM off

On “BNC INPUT” of “OPTION1” menu, select “COMP.”.

On “OPTION1”menu, select “OSM”, then press the MENU/

ENTER button.

The “OSM” menu appears.

OPTION 1

1 / 4

OSM

BNC INPUT

D-SUB INPUT

RGB SELECT

COMP.

RGB

AUTO

On “DISPLAY OSM” of “OSM” menu, select “OFF”.

HD SELECT

INPUT SKIP

ALL RESET

1080B

OFF

OSM

DISPLAY OSM

OSM ADJ.

OSM ANGLE

OSM ORBITER

OSM CONTRAST

OFF

LOW

EXIT

RETURN

SEL.

ADJ.

Information

Ⅵ BNC INPUT Settings

EXIT

RETURN

SEL.

ADJ.

RGB: Use the 5BNC terminals for RGB input.

COMP.: Use the 3BNC terminals for component input.

SCART1: Use the 4BNC terminals for RGB with

composite sync. See page En-9.

SCART2: Use the 3BNC terminals for RGB and the

VIDEO1 terminal for composite sync. See page En-9.

Information

Ⅵ DISPLAY OSM settings

ON: The informations on screen size, volume control,

etc. will be shown.

OFF: The informations on screen size, volume control,

etc. will not be shown.

Setting the RGB1 connector

Select one of the signals being transmitted to the RGB1

terminal.

The DISPLAY button on the remote control will not

function either.

Ⅵ OSM ADJUST settings

Example: Set the “D-SUB INPUT” mode to “SCART3”

Adjusts the position of the menu when it appears on the screen.

The position can be set between 1 to 6.

On “D-SUB INPUT” of “OPTION1” menu, select

“SCART3”.

OPTION 1

1 / 4

OSM

BNC INPUT

D-SUB INPUT

RGB SELECT

RGB

SCART3

AUTO

HD SELECT

INPUT SKIP

ALL RESET

1080B

OFF

Ⅵ OSM ANGLE settings

EXIT

RETURN

SEL.

ADJ.

Sets the display format (landscape “H” or portrait “V”).

When the unit is installed vertically set the OSM

ANGLE at “V”.

Information

Ⅵ D-SUB INPUT Settings

RGB: Use the D-SUB terminal for RGB input.

SCART3: Use the D-SUB terminal for RGB signal fed

from SCART. See page En-9.

“H”

“V”

OPTION1

OPTION 1

OSM

BNC INPUT

OSM

RGB

AUTO

1080B

OFF

D-SUB INPUT

RGB SELECT

HD SELECT

INPUT SKIP

ALL RESET

BNC INPUT

RGB

D-SUB INPUT

OFF

RGB

SEL.

MENU/ENTER OK

RGB SELECT

EXIT RETURN

AUTO

HD SELECT

1080B

OFF

INPUT SKIP

ALL RESET

OFF

1024

768

SEL.

MENU/ENTER

EXIT

RETURN

* The menu language for “V” is English only.

* Some menu items including LONG LIFE mode will

not be displayed with “V”, but can be performed by

setting with “H” (See pages 19 and 20 for the menu

items that can be displayed with “V”).

Ⅵ OSM ORBITER settings

ON: The position of the menu will be shifted by eight

dots each time OSM is displayed.

OFF: OSM will be displayed at the same position.

Ⅵ OSM CONTRAST settings

NORMAL: OSM brightness is set to normal.

LOW: OSM brightness is set to lower.

En-24

Setting a computer image to the correct RGB

select screen

With the computer image, select the RGB Select mode

for a moving image such as (video) mode, wide mode or

digital broadcast.

Setting the Input Skip

When this is ON, signals which are not present will be

skipped over and only pictures whose signals are being

transmitted will be displayed.

This setting is valid only for the INPUT SELECT button

on the unit.

Example: Setting the “RGB SELECT” mode to

“852

480 ”

Example: Set to “ON”

On “RGB SELECT” of “OPTION1” menu, select

On “INPUT SKIP” of “OPTION1” menu, select “ON”.

“852

480”.

OPTION 1

1 / 4

OSM

OPTION 1

1 / 4

BNC INPUT

D-SUB INPUT

RGB SELECT

RGB

OSM

BNC INPUT

D-SUB INPUT

RGB SELECT

RGB

AUTO

HD SELECT

INPUT SKIP

ALL RESET

SEL.

1080B

OFF

852

480

HD SELECT

INPUT SKIP

ALL RESET

1080B

OFF

EXIT

RETURN

ADJ.

EXIT

RETURN

SEL.

ADJ.

Information

Ⅵ INPUT SKIP settings

Information

Ⅵ RGB SELECT modes

OFF: Regardless of the presence of the signal, scan

and display all signals.

ON: If no input signal is present, skip that signal.

AUTO: Select the suitable mode for the specifications

of input signals as listed in the table “Computer input

signals supported by this system” on page En-41.

The others: The available resolutions are shown.

See page En-41 for the details of the above settings.

* “SETTING NOW” will appear during the input search.

Resetting to the default values

Use these operations to restore all the settings (PICTURE,

AUDIO, IMAGE ADJUST, OPTION1~4, etc.) to the

factory default values.

Setting high definition images to the suitable

screen size

Use this procedure to set whether the number of vertical

lines of the input high definition image is 1035 or 1080.

Refer to page En-19 for items to be reset.

On “ALL RESET” of “OPTION1” menu, select “ON”, then

press the MENU/ENTER button.

Example: Setting the “HD SELECT” mode to “1035I”

On “HD SELECT” of “OPTION1” menu, select “1035I”.

OPTION 1

1 / 4

ALL RESET

OSM

BNC INPUT

D-SUB INPUT

RGB SELECT

RGB

OPTION 1

1 / 4

OSM

BNC INPUT

D-SUB INPUT

RGB SELECT

RGB

SETTING NOW

AUTO

HD SELECT

INPUT SKIP

ALL RESET

1080B

OFF

AUTO

HD SELECT

INPUT SKIP

ALL RESET

1035

OFF

SEL.

MENU/ENTER OK

EXIT RETURN

When the “SETTING NOW” screen disappears, then all the

EXIT

SEL.

ADJ.

RETURN

settings are restored to the default values.

Information

Ⅵ HD SELECT modes

These 3 modes are not displayed in correct image

automatically.

1080B: Standard digital broadcasts

1035I: Japanese “High Vision” signal format

1080A: Special Digital broadcasts (for example :

DTC100)

En-25

Setting the picture to suit the movie

Option2 Settings Menu

The film image is automatically discriminated and

projected in an image mode suited to the picture.

[NTSC, PAL, PAL60, 480I (60 Hz), 525I (60 Hz), 576I

(50 Hz), 625I (50 Hz), 1035I (60 Hz), 1080I (60 Hz) only]

Set “ADVANCED OSM” to “ON” in the MAIN MENU.

Setting the power management for computer

images

This energy-saving (power management) function

automatically reduces the monitor’s power consumption

if no operation is performed for a certain amount of time.

Example: Setting the “CINEMA MODE” to “OFF”

On “CINEMA MODE” of “OPTION2” menu, select “OFF”.

Example: Turning the power management function on

OPTION 2

2 / 4

On “PWR. MGT.” of “OPTION2” menu, select “ON”.

PWR. MGT.

OFF

CINEMA MODE

LONG LIFE

GRAY LEVEL

S1/S2

PICTURE SIZE

DVI SET UP

PROTOCOL SET

OPTION 2

2 / 4

OFF

PWR. MGT.

CINEMA MODE

LONG LIFE

GRAY LEVEL

S1/S2

PICTURE SIZE

DVI SET UP

PROTOCOL SET

OFF

EXIT

RETURN

SEL.

ADJ.

OFF

Information

EXIT

RETURN

SEL.

ADJ.

Ⅵ CINEMA MODE

ON: Automatic discrimination of the image and

projection in cinema mode.

OFF: Cinema mode does not function.

Information

Ⅵ Power management function

* The power management function automatically reduces

the monitor’s power consumption if the computer’s

keyboard or mouse is not operated for a certain amount

of time. This function can be used when using the

monitor with a computer.

Reducing image retention

The brightness of the screen, the position of the picture,

positive/negative mode and screen wiper are adjusted to

reduce image retention.

* If the computer’s power is not turned on or if the

computer and selector tuner are not properly connected,

the system is set to the off state.

On “OPTION2” menu, select “LONG LIFE”, then press the

MENU/ENTER button.

The “LONG LIFE” screen appears.

* For instructions on using the computer’s power

management function, refer to the computer’s operating

instructions.

Ⅵ Power management settings

ON: In this mode the power management function is

turned on.

LONG LIFE

PLE

ORBITER

INVERSE

AUTO

AUTO1

OFF

SCREEN WIPER

SOFT FOCUS

EXIT

RETURN

SEL.

ADJ.

OFF: In this mode the power management function is

turned off.

Ⅵ Power management function and POWER/

STANDBY indicator

PLE (Peak Luminance Enhancement)

Use this to activate the brightness limiter.

Example: Setting “PLE” to “LOCK1”

The POWER/STANDBY indicator indicates the status

of the power management function. See below for

indicator status and description.

On “PLE” of “LONG LIFE” menu, select “LOCK1”.

LONG LIFE

PLE

ORBITER

INVERSE

SCREEN WIPER

SOFT FOCUS

LOCK1

AUTO1

OFF

POWER/STANDBY indicator

Power

POWER/

Power

management

operating status

Description

Turning the picture

back on

management STANDBY

EXIT

RETURN

SEL.

ADJ.

mode

indicator

Green

Not activated.

Activated.

Horizontal and vertical Picture already on.

synchronizing signals

are present from the

Information

Ⅵ PLE settings

AUTO: The brightness of the screen is adjusted

automatically to suit the picture quality.

LOCK1, 2, 3: Sets maximum brightness.

computer.

Off

Red

Horizontal and/or Operate the keyboard or

vertical synchronizing mouse. The picture

signals are not sent reappears.

from the computer.

The brightness level decreases in the order of LOCK

1, 2, 3. LOCK 3 provides minimum brightness.

En-26

ORBITER

INVERSE

Use this to set the picture shift.

Use this to set the inverse mode or to display a white

screen.

Example: Setting “ORBITER” to “AUTO2”

On “ORBITER” of “LONG LIFE” menu, select “AUTO2”.

Example: Setting “INVERSE” to “WHITE”

On “INVERSE” of “LONG LIFE” menu, select “WHITE”.

LONG LIFE

PLE

ORBITER

INVERSE

SCREEN WIPER

SOFT FOCUS

AUTO

AUTO2

OFF

PLE

ORBITER

INVERSE

SCREEN WIPER

SOFT FOCUS

AUTO

AUTO1

WHITE

OFF

EXIT

RETURN

SEL.

ADJ.

EXIT

RETURN

SEL.

ADJ.

Information

Ⅵ ORBITER settings

Information

Ⅵ INVERSE Settings

OFF: Orbiter mode does not function.

This is the default setting when RGB is input.

AUTO1: The picture moves around the screen

intermittently, making the picture smaller. This is the

default setting when a Video or a DVD/HD/DTV signal

is input. Set to “OFF” when these signals are not used.

AUTO2: The picture moves around the screen

intermittently, making the picture bigger.

MANUAL: User can adjust the orbiter function

(Horizontal Dot, Vertical Line and Time) manually.

See the following explanation.

ON: The picture is displayed alternately between

positive image and negative image.

You can set the time by pressing the MENU/ENTER

button while “ON” is set.

OFF: Inverse mode does not function.

WHITE: The entire screen turns white.

You can set the time by pressing the MENU/ENTER

button while “ON” is set.

Setting the time for INVERSE/WHITE

* When a Video or a DVD/HD/DTV signal is input, the

AUTO1 and 2 functions will affect only the moving

picture and will not make the screen smaller or bigger.

Set a time duration.

Example: Setting to that the INVERSE mode starts

in 2 hours and proceeds for one hour and a half.

On “INVERSE” of “LONG LIFE” menu, select “ON”, then

press the MENU/ENTER button.

THE “INVERSE/WHITE” screen appears.

Adjust the ORBITER function manually

Set the amount of shift and the time between movement.

Example: Setting so that the picture moves 2 dots

horizontally and 4 lines vertically every 3 minutes.

Adjust the times.

INVERSE/WHITE

WORKING TIME

WAITING TIME

01H30M

02H00M

On “ORBITER” of “LONG LIFE” menu, select

“MANUAL”, then press the MENU/ENTER button.

THE “ORBITER” screen appears.

EXIT

RETURN

SEL.

ADJ.

Adjust the items.

ORBITER

H-DOT

V-LINE

TIME

2 DOT

4 LINE

3 M

Information

Ⅵ Setting the time

WORKING TIME: Set the time duration for

“INVERSE/WHITE”.

EXIT

RETURN

SEL.

ADJ.

When the WORKING TIME is set to “ON” the mode

will stay on.

Information

WAITING TIME: Set the standby time until the

“INVERSE/WHITE” mode starts.

* The “WAITING TIME” can not be set when the

“WORKING TIME” is ON.

Ⅵ ORBITER Function settings

H-DOT: Moves from 1 dot to 20 dots in the horizontal

direction.

V-LINE: Moves from 1 line to 20 lines in the vertical

direction.

THE “WORKING TIME” and “WAITING TIME” can be

set for up to 12 hours and 45 minutes in units of 3 minutes.

* Ending a WORKING TIME function, the monitor will

go to STANDBY.

TIME: Interval of 1 minute to 5 minutes (1 horizontal

dot or 1 vertical line per interval).

[Example]

WORKING TIME: 01H30M

WAITING TIME: 02H00M

←−−−− 2 H −−−−→←−− 1.5 H −−→←−−−−

Start

INVERSE/WHITE Start STANDBY

Ⅵ To select “ON” for the “WORKING TIME”...

Set the hours of the working time to 0H and the minutes

to 0M. “ON” will be displayed.

En-27

SCREEN WIPER

SOFT FOCUS

When this is set to ON, a white vertical bar moves

repeatedly from the left and of the screen to the right end

at a constant speed.

Reduces edges and softens the image.

Example: Setting “SOFT FOCUS” to “2”

On “SOFT FOCUS” of “LONG LIFE” menu, select “2”.

Example: Setting “SCREEN WIPER” to “ON”

LONG LIFE

PLE

ORBITER

INVERSE

SCREEN WIPER

SOFT FOCUS

AUTO

AUTO1

OFF

On “SCREEN WIPER” of “LONG LIFE” menu, select

“ON”.

LONG LIFE

PLE

ORBITER

INVERSE

SCREEN WIPER

SOFT FOCUS

AUTO

AUTO1

OFF

EXIT

RETURN

SEL.

ADJ.

Information

Ⅵ SOFT FOCUS settings

EXIT

RETURN

SEL.

ADJ.

OFF: Turns the SOFT FOCUS function off.

1, 2, 3, 4: Activates the SOFT FOCUS setting. The

higher numbers create a softer image.

“SHARPNESS” can not be adjusted in the “PICTURE”

menu.

Information

Ⅵ SCREEN WIPER

ON: The white vertical bar appears.

You can set the time by pressing the MENU/ENTER

button while “ON” is set.

Setting the gray level for the sides of the screen

Use this procedure to set the gray level for the parts on the

screen on which nothing is displayed when the screen is

set to the 4:3 size.

OFF: Screen wiper mode does not function.

Setting the time for SCREEN WIPER

Example: Setting “GRAY LEVEL” to “5”

Set a time duration and the speed.

On “GRAY LEVEL” of “OPTION2” menu, select “5”.

Example: Setting so that the SCREEN WIPER mode

starts in 30 minutes and proceeds for one and a half

hours.

OPTION 2

2 / 4

PWR. MGT.

OFF

CINEMA MODE

LONG LIFE

GRAY LEVEL

S1/S2

PICTURE SIZE

DVI SET UP

PROTOCOL SET

On “SCREEN WIPER” of “LONG LIFE” menu, select

“ON”, then press the MENU/ENTER button.

THE “SCREEN WIPER” screen appears.

Adjust the times and speed.

OFF

EXIT

RETURN

SEL.

ADJ.

SCREEN WIPER

WORKING TIME

WAITING TIME

SPEED

01H30M

00H30M

Information

Ⅵ GRAY LEVEL settings

EXIT

RETURN

SEL.

ADJ.

This adjusts the brightness of the black (the gray level)

for the sides of the screen.

The standard is 0 (black). The level can be adjusted

from 0 to 15. The factory setting is 3 (dark gray).

Information

Ⅵ Setting the time

WORKING TIME: Set the time duration for “SCREEN

WIPER”.

When the WORKING TIME is set to “ON” the mode

will stay on.

WAITING TIME: Set the standby time until the

“SCREEN WIPER” mode starts.

SPEED: Set the moving speed for the “SCREEN

WIPER”. The speed decreases as the number increases.

Setting the screen size for S1/S2 video input

If the S-video signal contains screen size information, the

image will be automatically adjusted to fit the screen when

this S1/S2 is set to AUTO.

This feature is available only when an S-video signal is

input via the VIDEO3 terminal.

Example: Setting the “S1/S2” to “AUTO”

On “S1/S2” of “OPTION2” menu, select “AUTO”.

* The “WAITING TIME” can not be set when the

“WORKING TIME” is ON.

OPTION 2

2 / 4

PWR. MGT.

OFF

* THE “WORKING TIME” and “WAITING TIME” can

be set for up to 12 hours and 45 minutes in units of 3

minutes.

Ⅵ To select “ON” for the “WORKING TIME”...

Set the hours of the working time to 0H and the minutes

to 0M. “ON” will be displayed.

CINEMA MODE

LONG LIFE

GRAY LEVEL

S1/S2

PICTURE SIZE

DVI SET UP

PROTOCOL SET

AUTO

OFF

EXIT

RETURN

SEL.

ADJ.

Information

Ⅵ S1/S2 settings

AUTO:Adjusts the screen size automatically according

to the S1/S2 video signal.

OFF: Turns the S1/S2 function off.

En-28

Setting the picture size for RGB input signals

Use this procedure to switch the setting to “ON” or “OFF”.

* This function is available only for 50 and 60 inch types.

Option3 Settings Menu

Set “ADVANCED OSM” to “ON” in the MAIN MENU.

Using the timer

Example: Setting the “PICTURE SIZE” mode to

“OFF”

This function sets the day of the week and time. You can

also set the program timer which turns on or off the power

at the day of the week, time and the input mode you want,

or repeat timer which displays two input modes alternately.

On “OPTION3” menu, select “TIMER”, then press the

MENU/ENTER button.

On “PICTURE SIZE” of “OPTION2” menu, select “OFF”.

OPTION 2

2 / 4

PWR. MGT.

OFF

CINEMA MODE

LONG LIFE

GRAY LEVEL

S1/S2

PICTURE SIZE

DVI SET UP

PROTOCOL SET

The “TIMER” screen appears.

OFF

TIMER

PRESENT TIME

TIMER

OFF

EXIT

RETURN

SEL.

ADJ.

MENU/ENTER

EXIT

RETURN

SEL.

Setting the signal and black level for DVI signal

Choose the signal for the DVI connector (PC or STB/

DVD) and set the black level.

PRESENT TIME

This sets the day of the week and present time.

Example: Setting the “PLUG/PLAY” mode to “STB/

DVD”

Example: Setting “WEDNESDAY”, “22:05”

On “TIMER” menu, select “PRESENT TIME”, then press

the MENU/ENTER button.

The “PRESENT TIME” screen appears.

On “OPTION2” menu, select “DVI SET UP”, then press the

MENU/ENTER button.

The “DVI SET UP” screen appears.

On “PLUG/PLAY” of “DVI SET UP” menu, select “STB/

Adjust the items.

PRESENT TIME

RETURN

DVD”.

SUMMER TIME

OFF

DVI SET UP

PLUG/PLAY

BLACK LEVEL

STB/DVD

HIGH

WEDNESDAY

22 : 05 : 00

SET

SEL.

EXIT

RETURN

SEL.

ADJ.

EXIT

RETURN

ADJ.

Select “SET”, then press the MENU/ENTER button.

The adjustments are stored and the TIMER menu reappears.

* If you press the EXIT button instead of the MENU/ENTER

button, the settings can not be made.

Information

Ⅵ PLUG/PLAY settings

PC: When connected to the PC signal.

BLACK LEVEL is set to “LOW” automatically.

STB/DVD: When connected to the SET TOP BOX,

DVD etc.

PRESENT TIME

RETURN

SUMMER TIME

OFF

BLACK LEVEL is set to “HIGH” automatically.

Ⅵ BLACK LEVEL settings

WEDNESDAY

22 : 05 : 00

LOW: When connected to the PC signal.

HIGH: When connected to the SET TOP BOX, DVD

etc. Change “HIGH” into “LOW” if the black level

appears gray.

SET

SEL.

MENU/ENTER

EXIT

RETURN

Information

Ⅵ PRESENT TIME settings

SUMMER TIME: Use to set SUMMER TIME.

ON: The present time + 1 hour.

OFF: Cancelled

Day: Set the day of the week (e.g. Sunday).

Hour: Set the hour in the 24-hour format (range 00 to

23).

Setting the Protocol set

Use this setting when connecting a device which uses

special protocol for RS-232C communication.

Example: Setting “ON”

On “PROTOCOLSET” of “OPTION2” menu, select “ON”.

OPTION 2

2 / 4

Minutes: Set the minutes (range 00 to 59).

PWR. MGT.

OFF

CINEMA MODE

LONG LIFE

GRAY LEVEL

S1/S2

PICTURE SIZE

DVI SET UP

PROTOCOL SET

OFF

EXIT

RETURN

SEL.

ADJ.

Information

Ⅵ PROTOCOL SET settings

ON: When special protocol is used.

OFF: When NEC protocol is used (normal).

* Consult your dealer for details of protocol.

En-29

PROGRAM TIMER

Ⅵ Special characters in the PROGRAM TIMER

screen

When the setting item includes gray indication, it does

not function under the timer’s setting.

This sets the day and time at which the power will be

switched ON/OFF as well as the input mode.

Example 1: Setting so that the power will be switched

on at 8:30 A.M., Monday, displaying RGB2 source,

and switched off at 10:30 A.M.

PROGRAM TIMER

FUNC.

INV.

—

DAY

OFF

INPUT

RGB2

—

1 MON 08 : 30 10 : 30

2 TUE - - : - - 18 : 15

On “TIMER” menu, select “PROGRAM”, then press the

WHITE

—

REP.1

—

3 SAT 08 : 30 12 : 15 VIDEO1

MENU/ENTER button.

The “PROGRAM TIMER” screen appears.

Adjust the items.

4 *FRI 08 : 30 10 : 00

- - : - - - - : - -

6 SAT 08 : 30 12 : 15

DVD1

—

15 : 30 16 : 00

- - : - - - - : - -

RGB1

—

ᮤ ᮣ

Use the LM and

buttons to move the cursor.

Each mode switches each time the ZOOM

button is

pressed.

Depending on the selected INPUT or FUNC., press the

MENU/ENTER button to make advanced settings.

PROGRAM TIMER

• An asterisk “*” in the DAY field

An asterisk “*” means “every” or “everyday”. For

example, “*FRI” means “every Friday”. If you enter

“*” only, it means “everyday”.

• A hyphen “-” in the ON field or OFF field

You have to set at least the ON field or OFF field to

activate the program timer.

FUNC.

INV.

—

DAY

OFF

INPUT

RGB2

—

1 MON 08 : 30 10 : 30

—

- - : - -

• A hyphen “-” in the INPUT and FUNC. field

A hyphen “-” in the INPUT field means the last mode.

When you set “REP.1~3” in the FUNC. field, the

INPUT field is set to “-”.

—

Ⅵ To set MULTI INPUT

ZOOM

EXIT

SEL.

ADJ.

• Set the INPUT field to “MULTI”, then press the

MENU/ENTER button.

The “MULTI SCREEN SETTING” will appear on

the screen.

Example 2: Setting so that the power will be switched

on at 8:00 A.M., Monday, displaying the VIDEO1

input, display the RGB1 input at 9:00 A.M., display in

WHITE at 10:00A.M., then switched off at 11:00A.M.

• Use the L and M buttons to select “MULTI MODE”,

ᮤ

ᮣ

then use the

and

buttons to choose from

8:00

9:00

10:00

11:00

VIDEO1

PROGRAM 1

PROGRAM 2

PROGRAM 3

“SINGLE”, “SIDE BY SIDE1~3” and “PICTURE

IN PICTURE (BOTTOM LEFT~TOP LEFT)”.

• Use the L and M buttons to select “MAIN”/ “SUB”

RGB1

WHITE

ᮤ

ᮣ

and “LEFT”/“RIGHT”, then use the and buttons

to choose from “VIDEO1~3”, “DVD1~2” and

“RGB1~3”.

OFF

PROGRAM TIMER

FUNC.

—

WHITE

—

DAY

OFF

INPUT

1 MON 08 : 00

- - : - - VIDEO1

PICTURE IN PICTURE

SIDE BY SIDE

2 MON 09 : 00 - - : - -

3 MON 10 : 00 11 : 00

RGB1

—

PROGRAM TIMER

MULTI SCREEN SETTING

MULTI MODE

MULTI SCREEN SETTING

MULTI MODE

SIDE BY SIDE1

—

- - : - -

—

BOTTOM LEFT

INPUT MODE

MAIN

SUB

INPUT MODE

LEFT

RIGHT

* To perform a continuous program, set the OFF time only

for the last item.

RGB1

VIDEO1

RGB1

VIDEO1

SEL.

ADJ.

EXIT RETURN

SEL.

ADJ.

Information

Ⅵ PROGRAM TIMER settings

Ⅵ To set “REP.1~3” to the FUNC.

• Set the function to “REP.1”, “REP.2” or “REP.3”, then

press the MENU/ENTER button.

DAY: Set the day of the week (e.g. Sunday).

ON (hour, minutes): Set the time at which the power

will be turned on in the 24-hour format.

OFF (hour, minutes): Set the time at which the power

will be turned off in the 24-hour format.

INPUT: Set the input mode that will be displayed when

the power is turned on from “VIDEO1~3”, “DVD1~2”,

“RGB1~3” and “MULTI”.

The “REPEAT TIMER” screen will appear on the

screen.

ᮤ

ᮣ

• Use the and buttons to choose from “SINGLE”,

“MULTI” and “VIDEO-W”, then adjust the items.

• When you set FUNC. to “REP.1”, “REP.2” or

“REP.3”, you can set “SINGLE”, “MULTI” and

“VIDEO-W”. However, only one of these works

depending on the settings ofAUTO ID and DIVIDER.

See “REPEAT TIMER” on page En-30 for details

for the above settings.

FUNC.: Set the function that will be activated after the

power is turned on from “ORB.”, “INV.”, “WHITE”,

“WIPER” and “REP.1~3”.

“REP.1~3” cannot be selected when INPUT is set.

Ⅵ To reset the program

REPEAT TIMER

Align the cursor with the DAY field that you wish to

reset, then press the CLEAR/SEAMLESS SW button.

Ⅵ To reset the data

This function enables you to display 2 input modes at the

set time alternately.

Example: Setting to display “VIDEO1” for 10 minutes

Align the cursor with the field (ON/OFF/INPUT/

FUNC.) that you wish to reset, then press the CLEAR/

SEAMLESS SW button.

and “DVD1” for 15 minutes alternately.

On “TIMER” menu, select “REPEAT”, then press the

En-30MENU/ENTER button.

The “REPEAT TIMER” screen appears.

Setting the power on mode

This function sets the input mode and the sound volume

at the time the power is switched on.

Adjust the items.

ᮤ

ᮣ

Use the and buttons to select “SINGLE”.

Example: Setting the input mode to “VIDEO2”

ᮤ

Use the L and M buttons to select the item, then press the

ᮣ

and buttons to set.

On “OPTION3 ” menu, select “PWR.ON MODE ”, then

press the MENU/ENTER button.

REPEAT TIMER

1 WORK TIME

INPUT MODE

SINGLE

00H10M

VIDEO1

The “PWR.ON MODE ” screen appears.

On “INPUT ” of “PWR.ON MODE ” menu, select

“VIDEO2”.

2 WORK TIME

INPUT MODE

00H15M

DVD1

The available inputs depend on the setting of input.

EXIT

RETURN

SEL.

ADJ.

PWR. ON MODE

INPUT

VOLUME

VIDEO2

LAST

Information

Ⅵ REPEAT TIMER function

EXIT

RETURN

SEL.

ADJ.

* The two repeat timers run consecutively, i.e., Timer 1-

Timer 2-Timer1-Timer2.

* This becomes effective when the on-screen menu goes

out.

Information

Ⅵ INPUT settings

LAST: Last mode (the input that was last selected at

the time the power was switched off).

VIDEO1, 2, 3: VIDEO input mode.

RGB1, 2, 3: RGB input mode.

DVD/HD1, 2: DVD/HD input mode.

DVD/HD2, 3: DVD input mode.

MULTI: Multi screen mode.

Ⅵ SINGLE settings

WORK TIME: Set the time duration of the display.

Time range is from 1 minute to 24 hours.

INPUT MODE: Set the signal that will be displayed.

* Set the DIVIDER “OFF” and ID NUMBER “ALL”

before the operation.

Ⅵ MULTI settings

Follow the procedure used for PROGRAM TIMER. See

page En-30.

MODE: Select the input mode to be displayed from

“SINGLE”, “S BY S1~3” and “PICTURE IN

PICTURE (BTM LFT~TOP LFT)”.

PICTURE IN PICTURE

SIDE BY SIDE

PWR. ON MODE

WORK TIME: Set the time duration of the display.

Time range is from 1 minute to 24 hours.

INPUT MODE: Set the signal that will be displayed.

Select “MAIN” or “SUB” for “PICTURE IN PICTURE

(BTM LFT~TOP LFT)” and “LEFT” or “RIGHT” for

“S BY S1~3”.

MULTI SCREEN SETTING

MULTI MODE

BOTTOM LEFT

MULTI SCREEN SETTING

MULTI MODE

SIDE BY SIDE1

INPUT MODE

MAIN

INPUT MODE

LEFT

DVD/HD1

VIDEO1

DVD/HD1

VIDEO1

SUB

RIGHT

SEL.

ADJ.

EXIT RETURN

SEL.

ADJ.

EXIT RETURN

Ⅵ VOLUME settings

Only one signal is selected for “SINGLE”.

LAST: Last mode (the volume that was last selected at

the time the power was switched off).

0 to 42: The level of sound volume.

REPEAT TIMER

1 MODE

WORK TIME

INPUT MODE

MAIN

SUB

2 MODE

WORK TIME

INPUT MODE

LEFT

MULTI

BTM LFT

04H00M

RGB1

Enabling/disabling the front panel controls

This function enables/disables the front panel controls.

VIDEO1

S BY S1

02H30M

Example: Setting “ON”

RGB3

DVD1

RIGHT

On “CONTROL LOCK” of “OPTION3” menu, select

EXIT

RETURN

SEL.

ADJ.

“ON”, then press the MENU/ENTER button.

* Set the DIVIDER “OFF” and ID NUMBER “ALL”

before the operation.

OPTION 3

TIMER

3 / 4

Ⅵ VIDEO WALL settings

DIVIDER: Divide the screens into 1, 2

2 or 3

sections.

WORK TIME: Set the time duration of the display.

Time range is from 1 minute to 24 hours.

INPUT MODE: Set the signal that will be displayed.

* Turn on theAUTO ID and set the DIVIDER (at 1, 2

or 3

3) before the operations.

PWR. ON MODE

CONTROL LOCK

IR REMOTE

LOOP OUT

REMOTE ID

ID NUMBER

VIDEO WALL

OFF

ALL

EXIT

RETURN

SEL.

ADJ.

Information

Ⅵ CONTROL LOCK settings

ON: Disables the buttons on the front panel.

OFF: Enables the buttons on the front panel.

* In the case of Video Wall, timer No.1 can be used to

control all the displays simultaneously.

REPEAT TIMER

* Even when the CONTROL LOCK is set, the POWER

switch will not be locked.

REPEAT TIMER

1 DIVIDER

WORK TIME

INPUT MODE

VIDEO WALL

00H03M

VIDEO1

* This becomes effective when the on-screen menu goes

out.

2 DIVIDER

00H06M

RGB1

WORK TIME

INPUT MODE

EXIT

RETURN

SEL.

ADJ.

En-31

Enabling/disabling remote control wireless

transmission

This function enables/disables remote control wireless

transmission.

• Press and hold the POWER ON button, and release the

button when the indication saying that the code is set is

displayed. Or, press and hold the POWER STANDBY

button, and release the button when the power is turned

off.

Example: Setting “OFF”

Information

On “IR REMOTE”of “OPTION3”menu, select “OFF”, then

press the MENU/ENTER button.

Ⅵ REMOTE ID setting

ALL: The remote code is not set.

1 to 4: The specified remote code is applied.

OPTION 3

TIMER

3 / 4

PWR. ON MODE

CONTROL LOCK

IR REMOTE

LOOP OUT

REMOTE ID

ID NUMBER

VIDEO WALL

OFF

ALL

ID number setting

When using more than one of these displays, this function

sets ID numbers so that operation of the remote control

does not cause multiple monitors to operate at the same

time.

EXIT

RETURN

SEL.

ADJ.

Example: Setting “2”

Information

Ⅵ IR REMOTE settings

On “ID NUMBER” of “OPTION3” menu, select “2”.

ON: Enables remote control wireless transmission.

OFF: Disables remote control wireless transmission.

Set “OFF” to avoid unwanted control from other remote

controls.

OPTION 3

TIMER

3 / 4

PWR. ON MODE

CONTROL LOCK

IR REMOTE

LOOP OUT

REMOTE ID

ID NUMBER

VIDEO WALL

OFF

ALL

Loop Out setting

When this feature is set to ON, the received signal will be

looped out.

EXIT

RETURN

SEL.

ADJ.

* To reset back to ALL

Press the CLEAR/SEAMLESS SW button

Example: Setting “ON”

On “LOOP OUT” of “OPTION3” menu, select “ON”.

Information

Ⅵ ID NUMBER settings

OPTION 3

TIMER

3 / 4

PWR. ON MODE

CONTROL LOCK

IR REMOTE

LOOP OUT

REMOTE ID

ID NUMBER

VIDEO WALL

ALL: ID NUMBER will not be set.

1 to 256: ID NUMBER will be set.

Ⅵ When the ID NUMBER have been set

You can also set ID NUMBER for each remote control

to operate the plasma display individually. To do so,

see the following explanation.

OFF

ALL

EXIT

RETURN

SEL.

ADJ.

Information

Ⅵ LOOP OUT settings

To set the ID number for the remote control

ON: The received signal will be looped out via RGB1

terminal or VIDEO1 terminal.

OFF: The received signal will not loop out.

Example: Setting “2”

Press the ID SELECT button on the remote control.

The “ID SELECT” screen appears.

On “ID NUMBER” of “ID SELECT” menu, select “2”.

* Even if LOOP OUT is ON, signals won’t be sent out if

POWER is being turned off.

Ⅵ To connect another display...

See page En-6.

ID SELECT

POSITION :

ID NUMBER

Ⅵ If the RGB/PC1 signal is present at the time

the power switched on...

EXIT

ADJ.

RETURN

The RGB1 input will be displayed regardless of the

setting of LOOP OUT.

* To reset back to ALL

Press the CLEAR/SEAMLESS SW button

REMOTE ID setting

Set the remote code to adapt the plasma monitor to the

remote control.

Example: Setting to “1”

On the “REMOTE ID” of “OPTION3” menu, select “1”.

OPTION 3

TIMER

3 / 4

PWR. ON MODE

CONTROL LOCK

IR REMOTE

LOOP OUT

REMOTE ID

ID NUMBER

VIDEO WALL

OFF

ALL

EXIT

SEL.

ADJ.

RETURN

En-32

Video Wall setting

Use this feature to configure a (2

2, 3

3, 4

4, 5

1, 1

5) video wall.

On “OPTION3” menu, select “VIDEO WALL”, then press

the MENU/ENTER button.

Information

Ⅵ VIDEO WALL POSITION settings

1 Screen: There is no need to set POSITION.

2 Screens

3 Screens

The “VIDEO WALL” screen appears.

NO. 7

NO. 10

NO. 13

NO. 8

NO. 11

NO. 14

NO. 9

NO. 12

NO. 15

NO. 1

NO. 2

NO. 3

VIDEO WALL

DIVIDER

OFF

POSITION

NO. 4

DISP. MODE

AUTO ID

SPLIT

OFF

IMAGE ADJUST

P. ON DELAY

PLE LINK

OFF

4 Screens

5 Screens

NO. 32 NO. 33 NO. 34 NO. 35 NO. 36

NO. 37 NO. 38 NO. 39 NO. 40 NO. 41

NO. 42 NO. 43 NO. 44 NO. 45 NO.46

NO. 47 NO. 48 NO. 49 NO. 50 NO. 51

NO. 52 NO. 53 NO. 54 NO. 55 NO. 56

NO. 16 NO. 17 NO. 18 NO. 19

NO. 20 NO. 21 NO. 22 NO. 23

NO. 24 NO. 25 NO. 26 NO. 27

NO. 28 NO. 29 NO. 30 NO. 31

EXIT

RETURN

SEL.

ADJ.

Note: A contingency method of shutting off the electric

power should be used in cases of emergency during video

wall setup.

1 Screens

5 Screens

DIVIDER

NO. 1 NO. 2 NO. 3 NO. 4 NO. 5

NO. 1

NO. 2

NO. 3

NO. 4

NO. 5

Set the video wall.

Example: Setting “2

2”

On “DIVIDER” of “VIDEO WALL” menu, select “2

2”.

VIDEO WALL

DIVIDER

POSITION

DISP. MODE

AUTO ID

IMAGE ADJUST

P. ON DELAY

PLE LINK

SPLIT

OFF

Select the screen mode between two choices (Splitting,

Blanking).

OFF

Example: Setting “BLANK”

EXIT

RETURN

SEL.

ADJ.

On “DISP. MODE” of “VIDEO WALL” menu, select

“BLANK”.

Information

VIDEO WALL

Ⅵ DIVIDER settings

DIVIDER

POSITION

OFF, 1: 1 Screen (Matrix display function does not work)

2: 4 Screens

3: 9 Screens

DISP. MODE

AUTO ID

IMAGE ADJUST

P. ON DELAY

PLE LINK

BLANK

OFF

4: 16 Screens

5: 25 Screens

EXIT

RETURN

SEL.

ADJ.

1: 5 Screens horizontally

5: 5 Screens vertically

Information

Ⅵ DISP. MODE settings

* When you select 2

2, 3

3, 4

4, 5

5, 5

1, 1

SPLIT: Combines enlarged screens and creates multiple

screens.

set the VIDEO WALL POSITION.

BLANK: Corrects misalignment of combined screen

portions and creates multiple screens.

VIDEO WALL POSITION

Set the position of each display.

Example: Setting “4”

AUTO ID

On “VIDEO WALL” menu, select “POSITION”, then press

the MENU/ENTER button.

The “VIDEO WALL POSITION” screen appears.

This feature automatically sets the ID numbers of multiple

displays connected to each other.

Example: Setting “ON”

Select “4” of “POSITION NO.”.

Set the ID number for the No. 1 display on ID NUMBER

menu.

On “AUTO ID” of “VIDEO WALL” menu, select “ON”,

then press the MENU/ENTER button.

VIDEO WALL POSITION

POSITION NO.

AUTO ID

EXIT

ADJ.

RETURN

WIRED CABLE

CONNECTION TURN

EXIT

ADJ.

RETURN

En-33

control the No.1 monitor will turn on and the others

will be turned on one by one automatically.

* From the second monitor onward, neither the POWER

button on the unit nor the POWER ON button on the

remote control works. However, by pressing and holding

the POWER ON button for more than 3 seconds, the

monitor will be turned on.

Information

Ⅵ AUTO ID settings

ON: EnablesAuto ID function. In the case shown below,

display 1 will be set as ID 1, display 2 as ID2, etc.

This can be set only when a 2

2, 3

3, 1

5 or 5

is selected.

REMOTE

OUT

OFF: Turns on the main power of all displays at the

same time.

No.1

No.2

REMOTE

OUT

REMOTE

No.4 No.3

REMOTE

Display 2

Display 1

(Only for 4

4 and 5

5 video wall modes)

MODE1: Turns on the main power of each display

delayed.

MODE2:Turns on the main power of each display more

delayed.

REMOTE

OUT

No.1

No.2

REMOTE

OUT

REMOTE

No.4 No.3

REMOTE

Display 3

Display 4

OFF: Turns on the main power of all displays at the

same time.

Note: To use this function, you have to connect the

displays with the remote cable (not supplied).

OFF: Disables Auto ID function.

Note: To use this function, you have to connect the

displays with the remote cable (not supplied).

IMAGE ADJUST

PLE LINK

The position of the image can be adjusted and flickering

of the image can be corrected.

Use this function to set a uniform brightness for each display.

Turn on the AUTO ID and set the DIVIDER (at 1, 2

3, 1

5 or 5

1) before the following operations.

Example: Adjusting the vertical position

Example: Setting “ON”

On “VIDEO WALL”menu, select “IMAGE ADJUST”, then

press the MENU/ENTER button.

The “IMAGE ADJUST” screen appears.

On “V-POSITION” of “IMAGEADJUST” menu, adjust the

position.

On “PLE LINK” of “VIDEO WALL” menu, select “ON”,

then press the MENU/ENTER button.

VIDEO WALL

DIVIDER

POSITION

IMAGE ADJUST

DISP. MODE

AUTO ID

IMAGE ADJUST

P. ON DELAY

PLE LINK

SPLIT

OFF

ASPECT MODE

V-POSITION

H-POSITION

V-HEIGHT

NORMAL

OFF

H-WIDTH

AUTO PICTURE

FINE PICTURE

PICTURE ADJ.

UNDERSCAN

OFF

EXIT

RETURN

SEL.

ADJ.

OFF

EXIT RETURN

V-POSITION

SEL.

ADJ.

Information

Ⅵ PLE LINK settings

Information

Ⅵ IMAGE ADJUST settings

These are the same functions as the IMAGE ADJUST

menu on page En-23.

ON: Sets a uniform brightness for each screen in a video

wall. This can be set only when a 1, 2

2, 3

3, 1

or 5

1 video wall is selected.

OFF: Sets the individual screen brightness for each

screen in a video wall.

P. ON DELAY (Power on delay)

* When this function is set “ON”, connect your plasma

displays with the remote cable (optional) in the order of

the position numbers for the 2

2 video wall. See the

drawing below.

Use this function to activate power-on delay.

Turn on the AUTO ID before the following operations.

Example: Setting “ON”

On “P. ON DELAY” of “VIDEO WALL” menu, select

“ON”.

* If there are changes in the DIVIDER or POSITION,

the PLE LINK will automatically turn OFF.

VIDEO WALL

REMOTE

OUT

DIVIDER

No.1

No.2

POSITION

REMOTE

OUT

REMOTE

DISP. MODE

AUTO ID

SPLIT

OFF

No.4 No.3

REMOTE

IMAGE ADJUST

P. ON DELAY

PLE LINK

Display 2

Display 1

OFF

REMOTE

OUT

EXIT

RETURN

SEL.

ADJ.

No.1

No.2

REMOTE

OUT

REMOTE

No.4 No.3

REMOTE

Display 3

Display 4

Information

* With the 3

3, 1

5 or 5

1 video wall, connect the

final display to the first display the same way as with

2 video wall.

Ⅵ P. ON DELAY settings

(Video wall modes other than 4

4 and 5

ON: Turns on the main power of each display after a

delay time.

Note:

* The remote control can be operated unless the IR

REMOTE is set to “OFF”.

* To use this function, you have to connect the displays

with the remote cable (not supplied).

* Once this function has been set to “ON”, POWER ON/

OFF button on the remote control does not function

except for the No.1 monitor.

By pressing the POWER ON button on the remote

En-34

S BY S: Will show the entire image on the sub screen

of side-by-side mode.

BTM LFT~TOP LFT: Will show the entire image on

the sub screen of picture-in-picture mode.

Option4 Settings Menu

Set “ADVANCED OSM” to “ON” in the MAIN MENU.

Removing the sub screen area when there is

no input signal detected for the sub picture

This function automatically removes the black frame of

the sub screen when there is no sub screen input signal.

This feature is available only when the picuture-in-picuture

mode is selected.

Side-by-Side

Picture-in-Picture

RGB1

Example: Setting “DISPLAY” to “FADE”

On “SUB. PICTURE” of “OPTION4” menu, press the

MENU/ENTER button.

The “SUB. PICTURE” screen appears.

Adjust the items.

POINTER button

Zoom+/- button

SUB. PICTURE

SUB. P DETECT

SUB. P RATE

DISPLAY

AUTO

100%

FADE

EXIT

RETURN

SEL.

ADJ.

POINTER button

Information

Ⅵ SUB. PICTURE Function

* Loss of the input signal means a condition in which the

video signal and the sync signal are not present.

* Under conditions in which the sub screen has

disappeared, the ZOOM NAV, PIC FREEZE, and

SEAMLESS SW functions will not work. The WIDE

button will not function either.

Ⅵ SUB. P DETECT setting

AUTO: Black frame with no signal input disappears 3

seconds after the input signal is lost.

Displaying still images in the sub screen

This feature enables display in the sub screen of still images

captured by pressing the SELECT/FREEZE button.

Example: Setting “PIC FREEZE” to “BTM LFT”

On “PIC FREEZE” of “OPTION4” menu, select “BTM

LFT”.

OFF: Black frame with no signal input is displayed

consistently.

OPTION 4

4 / 4

Ⅵ SUB. P RATE setting

Set the transparency of the sub screen.

Ⅵ DISPLAY setting

NORMAL: The sub screen is displayed consistently.

FADE: The sub screen fades in.

SUB. PICTURE

ZOOM NAV

PIC FREEZE

SEAMLESS SW

SELECT1

BTM LFT

OFF

—

OFF

EXIT

RETURN

SELECT2

TEXT INSERT

SEL.

ADJ.

Displaying the entire image during DIGITAL

ZOOM operations

Use this function to display the entire image within the

sub screen together with an enlarged image on the main

screen.

Information

Ⅵ PIC FREEZE Function

* This feature does not function during split screen mode.

* Digital zoom is not available while this function is

operating.

Example: Setting “ZOOM NAV” to “S BY S”

* A further press of the SELECT/FREEZE button while

this function is operating will cancel this function.

* Providing a 2-screen display will cancel this function.

Ⅵ PIC FREEZE settings

On “ZOOM NAV” of “OPTION4” menu, select “S BY S”.

OPTION 4

4 / 4

SUB. PICTURE

ZOOM NAV

PIC FREEZE

SEAMLESS SW

SELECT1

S BY S

S BY S1

OFF

—

OFF: Will not show the still image.

S BY S1, 2: The still images captured by pressing the

SELECT/FREEZE button will be shown on the sub

screen of side-by-side mode.

SELECT2

TEXT INSERT

OFF

EXIT

RETURN

SEL.

ADJ.

BTM LFT~TOP LFT: The still images captured by

pressing the SELECT/FREEZE button will be shown

on the sub screen of picture-in-picture mode.

Information

Ⅵ ZOOM NAV Function

* This feature does not function during split screen mode.

* This feature does not function while PIC FREEZE is

operating.

* Providing a 2-screen display will cancel this function.

Ⅵ ZOOM NAV settings

OFF: Will not show the entire image on the sub screen.

En-35

Displaying the information as a text

Side-by-Side

Picture-in-Picture

RGB1

Example: Setting “TEXT INSERT” to “BOTTOM-3”,

“INPUT” to “RGB1”, “SUB. P DETECT” to “AUTO”,

“PIC. RATE” to “100%” and “DISPLAY” to

“NORMAL”

RGB1

On “TEXT INSERT” of “OPTION4” menu, select

“BOTTOM-3”, then press the MENU/ENTER button.

The “TEXT INSERT” screen appears.

Adjust the items.

SELECT/

FREEZE

button

SELECT/

FREEZE

button

RGB1

S BY S1

TEXT INSERT

RGB1

INPUT

RGB1

AUTO

100%

NORMAL

SUB. P DETECT

PIC. RATE

DISPLAY

SEL.

ADJ.

EXIT RETURN

Enhanced split screen Model

S BY S2

Information

RGB1

Ⅵ TEXT INSERT setting

OFF: Displays no text.

BOTTOM-1/BOTTOM-2/BOTTOM-3/MID.LOW/

MID.HIGH/TOP-3/TOP-2/TOP-1/LEFT/RIGHT:

Displays a text at the specified location, where the

subscriptions -1, -2 and -3 indicate the height of the

text area.

Ⅵ INPUT setting

Sets the input of the text to the RGB1 to 3.

Ⅵ SUB. P DETECT setting

AUTO: Black frame with no signal input disappears

3 seconds after the input signal is lost.

OFF: Black frame with no signal input is displayed

consistently.

Switching the input source quickly

This feature enables quick input selection.

After setting ON, press the CLEAR/SEAMLESS SW

button for quick switching between the two selected input

signals.

Example: Set to switch quickly between RGB1 and

RGB2.

On “SEAMLESS SW” of “OPTION4” menu, select “ON”.

Select “RGB1” and “RGB2”.

Ⅵ PIC. RATE setting

Sets the transparency of the text.

Ⅵ DISPLAY setting

NORMAL: The sub screen is displayed consistently.

FADE: The sub screen fades in.

OPTION 4

4 / 4

SUB. PICTURE

ZOOM NAV

BTM LFT

S BY S1

RGB1

RGB2

OFF

PIC FREEZE

SEAMLESS SW

SELECT1

SELECT2

TEXT INSERT

EXIT

RETURN

SEL.

ADJ.

* The available sources depend on the settings of input.

Information

Ⅵ SEAMLESS SW Function

* This feature will not function for certain input

combinations. See the table on page En-16.

* After switching to the selected input, please operate this

function.

* This feature will not function during split screen mode.

* When SEAMLESS SW is first turned on, or when

signals being transmitted are changed, there may be a

slight delay due to signal analysis.

Ⅵ SEAMLESS SW settings

OFF: Turns off the SEAMLESS SW function.

ON: When the CLEAR/SEAMLESS SW button is

pressed, input signals will switch quickly according to

the setting of SELECT1 and SELECT2.

En-36

Advanced OSM Settings Menu

Setting the menu mode

This allows you to access the complete menu.

When P. ON DELAY or PLE LINK is ON, this won’t be

turned OFF.

Color System Settings Menu

Setting the video signal format

Use these operations to set the color systems of composite

video signals or Y/C input signals.

Example: Setting the color system to “3.58 NTSC”

Example: Setting “ON”

On the MAIN MENU, select “COLOR SYSTEM”, then press

the MENU/ENTER button.

On “ADVANCED OSM” of “MAIN MENU”, select “ON”.

The “COLOR SYSTEM” screen appears.

On “COLOR SYSTEM”, select “ 3.58NTSC ”.

MAIN MENU

PICTURE

AUDIO

IMAGE ADJUST

OPTION 1

1 / 2

MAIN MENU

PICTURE

AUDIO

IMAGE ADJUST

OPTION 1

OPTION 2

1 / 2

COLOR SYSTEM

OPTION 3

OPTION 4

3.58NTSC

ADVANCED OSM

OFF

ADVANCED OSM

EXIT

SEL.

ADJ.

EXIT EXIT

SEL.

ADJ.

EXIT

ADJ.

RETURN

Information

Ⅵ ADVANCED OSM settings

Information

Ⅵ Video signal formats

ON: All of the main menu items are available for

advanced users.

OFF: Some of the main menu items are not available

(e.g. OPTION2, OPTION3 and OPTION4).

Different countries use different formats for video

signals. Set to the color system used in your current

country.

AUTO: The color systems are automatically identified

and the format is set accordingly.

PAL: This is the standard format used mainly in the

United Kingdom and Germany.

SECAM: This is the standard format used mainly in

France and Russia.

4.43 NTSC, PAL60: This format is used for videos in

countries using PAL and SECAM video signals.

3.58 NTSC: This is the standard format used mainly

in the United States and Japan.

Language Settings Menu

Setting the language for the menus

The menu display can be set to one of 10 languages.

Example: Setting the menu display to “DEUTSCH”

On “MAIN MENU”, select “LANGUAGE”, then press the

MENU/ENTER button.

The “LANGUAGE” screen appears.

On “LANGUAGE”, select “ DEUTSCH”, then press the

MENU/ENTER button.

PAL-M: This is the standard format used mainly in

Brazil.

PAL-N: This is the standard format used mainly in

Argentina.

LANGUAGE

DEUTSCH

Source Information Menu

Checking the frequencies, polarities of input

signals, and resolution

MENU/ENTER

EXIT

RETURN

ADJ.

The “LANGUAGE” is set to “DEUTSCH” and return to the

Use this function to check the frequencies and polarities

of the signals currently being input from a computer, etc.

On “MAIN MENU”, select “SOURCE INFORMATION”,

then press the MENU/ENTER button.

main menu.

Information

Ⅵ Language settings

ENGLISH ........... English

DEUTSCH.......... German

FRANÇAIS ......... French

ESPAÑOL .......... Spanish

ITALIANO ........... Italian

SVENSKA .......... Swedish

ꢀУꢁꢁꢂꢃꢄ ............... Russian

EΛΛHNIKA ......... Greek

PORTUGUÊS .......... Portuguese

TÜRKÇE ............ Turkish

The “SOURCE INFORMATION” is displayed.

SOURCE INFORMATION

H. FREQUENCY

V. FREQUENCY

48.4KHZ

60.0HZ

H. POLARITY

V. POLARITY

NEG.

MEMORY

RESOLUTION

1024 768

EXIT

RETURN

PC:

MEMORY will be displayed.

Others: MODE will be displayed.

En-37

External Control Pin Assignments

Application

mini D-Sub 15-pin connector

(Analog)

These specifications cover the communications control of

the plasma monitor by external equipment.

RGB 1

Connections

Connections are made as described below.

15 14 13 12 11

External equipment

e.g., Personal computer

Pin No.

Signal (Analog)

Red

Green or sync-on-green

Blue

No connection

Ground

Red ground

Green ground

Blue ground

No connection

Sync signal ground

No connection

Bi-directional DATA (SDA)

Horizontal sync or Composite sync

Vertical sync

Display

Connector on the plasma monitor side: EXTERNAL

CONTROL connector.

Use a crossed (reverse) cable.

Type of connector: D-Sub 9-pin male

Data clock

Pin No.

Pin Name

No Connection

RXD (Receive data)

TXD (Transmit data)

DTR (DTE side ready)

GND

Pin No.

Pin Name

DSR (DCE side ready)

RTS (Ready to send)

CTS (Clear to send)

No connection

DVI-D 24-pin connector (Digital)

The unit is equipped with a type of connector commonly

used for digital.

(This cannot be used for an analog input.)

(TMDS can be used for one link only.)

RGB 3

Communication Parameters

(1) Communication system

(2) Interface

Asynchronous

10 11 12 13 14 15 16

RS-232C

9600 bps

8 bits

17 18 19 20 21 22 23 24

(3) Baud rate

(4) Data length

(5) Parity

Odd

Pin No.

Signal (Digital)

T.M.D.S Data 2 -

(6) Stop bit

1 bit

T.M.D.S Data 2 +

T.M.D.S Data 2 Shield

No connection

DDC Clock

(7) Communication code

Hex

External Control Codes (Reference)

FUNCTION

Power ON

OFF

CODE DATA

9FH 80H 60H 4EH 00H CDH

9FH 80H 60H 4FH 00H CEH

DDC Data

No connection

T.M.D.S Data 1 -

T.M.D.S Data 1 +

T.M.D.S Data 1 Shield

No connection

+5 V Power

Input Switch Video1 (BNC)

Video2 (RCA)

DFH 80H 60H 47H 01H 01H 08H

DFH 80H 60H 47H 01H 02H 09H

DFH 80H 60H 47H 01H 03H 0AH

DFH 80H 60H 47H 01H 05H 0CH

DFH 80H 60H 47H 01H 06H 0DH

Video3 (S-Video)

DVD1/HD1 (RCA)

DVD2/HD2 (BNC)

RGB1 (mini D-Sub 15-Pin) DFH 80H 60H 47H 01H 07H 0EH

RGB2 (5BNC)

RGB3 (DVI)

DFH 80H 60H 47H 01H 08H 0FH

DFH 80H 60H 47H 01H 0CH 13H

Audio Mute ON

9FH 80H 60H 3EH 00H BDH

9FH 80H 60H 3FH 00H BEH

OFF

Ground

Hot Plug Detect

T.M.D.S Data 0 -

T.M.D.S Data 0 +

T.M.D.S Data 0 Shield

No connection

T.M.D.S Clock Shield

T.M.D.S Clock +

T.M.D.S Clock -

Picture Mode NORMAL

THEAT. 1

DFH 80H 60H OAH 01H 01H CBH

DFH 80H 60H OAH 01H 02H CCH

DFH 80H 60H OAH 01H 03H CDH

DFH 80H 60H OAH 01H 04H CEH

DFH 80H 60H OAH 01H 05H CFH

THEAT. 2

DEFAULT

BRIGHT

Screen Mode STADIUM

DFH 80H 60H 51H 01H 02H 13H

DFH 80H 60H 51H 01H 03H 14H

DFH 80H 60H 51H 01H 04H 15H

DFH 80H 60H 51H 01H 05H 16H

DFH 80H 60H 51H 01H 08H 19H

DFH 80H 60H 51H 01H 09H 1AH

DFH 80H 60H 51H 01H 0AH 1BH

ZOOM

NORMAL

FULL

UNDERSCAN

14 : 9

2.35 : 1

Auto Picture ON

DFH 80H 60H 7FH 03H 03H 09H 00H 4DH

DFH 80H 60H 7FH 03H 03H 09H 01H 4EH

OFF

Cinema Mode ON

OFF

DFH 80H 60H C1H 01H 01H 82H

DFH 80H 60H C1H 01H 02H 83H

Note: Contact your local dealer for a full list of the

External Control Codes if needed.

En-38

Connection with STB

Following is the connection example of STB (Set-top Box)

using the REMOTE IN/OUT connectors of the plasma

monitor. Consult your dealer about the actual connection

and operation.

1/8 Stereo Mini Jack (not supplied)

for REMOTE IN/OUT

Plasma monitor REMOTE IN

* Connection Example

• STB has the REMOTE IN connector.

• The pin assignment of the REMOTE IN connector of

STB is same as that of 1/8 stereo mini cable connected

to the REMOTE OUT connector (En-39).

• The transmit frequency of the remote control of STB is

37.9 kHz (Typical).

GND DATA (DC +5 V) VDD (DC +3 V)

Plasma monitor REMOTE OUT

Connection Example: Connecting an STB

PLASMA DISPLAY

Video cable

GND DATA (C-MOS DC +5 V)

OUT

STB

OUT

Remote cable*

STB

Remote Control

Carrier fHz: 37.9 kHz (Typical)

* The 1/8 Stereo Mini cable must be purchased separately.

En-39

Troubleshooting

If the picture quality is poor or there is some other problem, check the adjustments, operations, etc., before requesting service.

Symptom

The unit emits a crackling sound.

Checks

• Are the image and sound normal?

Remedy

• If there are no abnormalities in the image and sound,

the noise is caused by the cabinet reacting to

changes in temperature. This will not affect

performance.

Picture is disturbed.

Sound is noisy.

• Is a connected component set directly in front or at • Leave some space between the display and the

the side of the display?

connected components.

Remote control operates erroneously.

The remote control does not work.

• Are the remote control’s batteries worn out?

• Is IR REMOTE set to ON?

• Replace both batteries with new ones.

• Set IR REMOTE OFF on OPTION3 menu.

• Has an ID number been set for the main unit?

• Set an ID number with the ID SELECT button, or set

the ID number to ALL.

Monitor’s power does not turn on when the

remote control’s power button is pressed.

• Is the monitor’s power cord plugged into a power

outlet?

• Plug the monitor’s power cord into a power outlet.

• Are all the monitor’s indicators off?

• Press the power button on the monitor to turn on the

power.

• Are the remote control’s batteries worn out?

• Replace both batteries with new ones.

• Is IR REMOTE set to OFF?

• Set IR REMOTE ON.

• Has an ID number been set for the main unit?

• Set an ID number with the ID SELECT button, or set

the ID number to ALL.

Monitor does not operate when the remote

control’s buttons are pressed.

• Is the remote control pointed at the monitor, or is

there an obstacle between the remote control and

the monitor?

• Point the remote control at the monitor’s remote

control sensor when pressing buttons, or remove the

obstacle.

• Is direct sunlight or strong artificial light shining on • Eliminate the light by closing curtains, pointing the

the monitor’s remote control sensor?

light in a different direction, etc.

•

Are the remote control’s batteries worn out?

• Replace both batteries with new ones.

• The remote cable is plugged into the REMOTE IN • Unplug the remote cable from the monitor.

terminal (Wired).

The front panel buttons of the main unit do

not function.

• The front panel buttons do not function during

Control Lock.

• Set the Control Lock to OFF.

No sound or picture is produced.

• Is the monitor’s power cord plugged into a power

outlet?

• Plug the monitor’s power cord into a power outlet.

Picture appears but no sound is produced.

• Is the volume set at the minimum?

• Is the mute mode set?

• Increase the volume.

• Press the remote control’s MUTE button.

• Connect the speakers properly.

• Are the speakers properly connected?

• Is AUDIO INPUT set correctly?

• Set AUDIO INPUT on the AUDIO menu correctly.

Poor picture with VIDEO signal input.

Poor picture with RGB signal input.

• Improper control setting.

Local interference.

Cable interconnections.

• Adjust picture control as needed.

Try another location for the monitor.

Be sure all connections are secure.

Input impedance is not correct level.

• Improper control setting.

Incorrect 15 PIN connector pin connections.

• Adjust picture controls as needed.

Check pin assignments and connections.

Tint is poor or colors are weak.

Nothing appears on screen.

• Are the tint and colors properly adjusted?

• Is the computer’s power turned on?

• Is a source connected?

• Adjust the tint and color (under PICTURE).

• Turn on the computer’s power.

• Connect source to the monitor.

• Is the power management function in the standby • Operate the computer (move the mouse, etc.).

or off mode?

• Is LOOP OUT set to ON?

• Set LOOP OUT OFF.

Part of picture is cut off or picture is not

centered.

• Is the position adjustment appropriate?

• Adjust the IMAGE ADJUST properly.

Image is too large or too small.

• Is the screen size adjustment appropriate?

• Press the WIDE button on the remote control and

adjust properly.

Picture is unstable.

• Is the computer’s resolution setting appropriate?

• Set to the proper resolution.

• Check the input signal.

POWER/STANDBY indicator is lighted in red. • Horizontal and / or vertical sync signal is not

present when the Intelligent Power Manager

control is on.

POWER/STANDBY indicator is blinking in

red.

• The temperature inside the main unit has become • Promptly switch off the power of the main unit and

too high and has activated the protector.

wait until the internal temperature drops. See*1.

POWER/STANDBY indicator is blinking in

green and red, or green.

• Prompty switch off the power of the main unit. See

*2.

——————

*1 Overheat protector

If the monitor becomes too hot, the overheat protector will be activated and the monitor will be turned off. If this happens, turn off the power to the monitor

and unplug the power cord. If the room where the monitor is installed is particularly hot, move the monitor to a cooler location and wait for the monitor

to cool for 60 minutes. If the problem persists, contact your dealer.

*2 In the following case, power off the monitor immediately and contact your dealer or authorized Service Center.

The monitor turns off 5 seconds after powering on and then the POWER/STANDBY indicator blinks. It indicates that the power supply circuit, plasma

display panel, temperature sensor, or one or more fans have been damaged.

En-40

Table of Signals Supported

Supported resolution (42XM5)

•

When the screen mode is NORMAL, each signal is converted to a 768 dots

768 lines signal. (Except for *³)

•

When the screen mode is FULL, each signal is converted to a 1024 dots

768 lines signal.

Computer input signals supported by this system

Sync Polarity

Horizontal Vertical Horizontal Vertical

Presence

Screen mode

NORMAL FULL

Vertical

Horizontal

frequency frequency

(Hz)

(kHz)

70.1

31.5

RGB

TEXT

INSERT

Dots

lines

Model

Signal Type

select*⁴

DVI

Memory

(4:3)

– –

(16:9)

YES

YES*²

YES

YES*²

YES

NEC PC-9800

– –

720

400

640

480

– –

640

400

720

400

640

480

YES

NEG

POS

NEG

POS

NEG

POS

NEG

POS

NEG

POS

NEG

POS

NEG

POS

NEG

POS

NEG

POS

NEG

POS

NEG

POS

NEG

POS

NEG

POS

NEG

POS

YES

– –

YES

– –

YES

70.1

59.9

72.8

75.0

85.0

100.4

120.4

85.1

60.0

56.3

60.3

72.2

75.0

85.1

99.8

120.0

60.0

70.1

75.0

85.0

100.6

119.4

75.0

60.0

72.0

56.2

59.8

69.8

59.8

60.0

85.0

60.0

59.9

60.0

75.0

85.0

100.1

60.0

74.9

85.0

60.0

65.0

70.0

75.0

85.0

50.0

60.0

59.9

60.0

66.7

74.6

74.9

75.1

59.9

31.5

37.9

37.5

43.3

51.1

61.3

37.9

31.0

31.7

35.2

37.9

48.1

46.9

53.7

63.0

75.7

48.4

56.5

60.0

68.7

80.5

95.5

67.5

53.7

64.9

45.1

48.0

56.0

49.7

53.1

60.0

85.9

47.7

48.3

64.0

80.0

91.1

108.5

65.3

82.3

93.9

65.3

75.0

81.3

87.5

93.8

106.3

56.2

67.5

74.6

74.0

35.0

49.7

60.2

68.7

55.9

– –

YES

– –

YES

– –

YES

– –

YES

– –

131

111

110

YES

– –

YES

– –

720

400

848

480

852

480*¹

800

600

YES

848

480 YES

852

480 YES

800

600 YES

– –

YES

– –

YES

– –

YES

– –

YES

IBM PC/AT

compatible

computers

1024

768 YES

1024

768

YES

1024

768

1024

768

– –

YES

YES*⁹

YES

– –

1152

864 YES

1152

864

1152

864

YES

– –

YES

1280

768 NO

1280

768

YES

1280

768

YES

– –

YES

1280

768

– –

YES

1280

800*⁷

1280

854

1280

960

1280

800 YES

– –

YES

1280

854 YES

– –

YES

– –

YES

– –

YES

YES*⁹

1360

765 NO

1360

768 YES

1376

768 YES

1280

1024 YES

1360

765

1360

768

1376

768

1280

1024

YES

– –

YES

– –

YES

YES*³

YES

– –

YES

YES*⁹

YES

– –

YES

1400

1050*⁷

1400

1050 YES

– –

YES

1680

1050*⁷

1680

1050 YES

1600

1200 YES

1600

1200

YES

– –

1920

1080*⁸

1920

1080 YES

YES

1920

1080

1920

1200 – –

– –

1920

1200*⁷

– –

1920

1200RB

– –

YES

1920

1200RB

640

480

832

624

– –

YES

– –

Sync on G Sync on G

Apple

Macintosh*⁵

– –

YES

– –

1024

768

1152

870

1440

900*⁷

YES

– –

YES

– –

YES

NEG

POS

YES

En-41

Screen mode

NORMAL FULL

Sync Polarity

Horizontal Vertical Horizontal Vertical

Presence

Vertical

Horizontal

frequency frequency

(Hz) (kHz)

60.0 64.6

RGB

TEXT

INSERT

Dots

lines

Model

select*⁴

DVI

Memory

Signal Type

(4:3)

YES*³

YES

(16:9)

YES 1280

1024 YES YES*⁹

1280

1024

Work Station

(EWS4800)

NEG

– –

NEG

– –

YES

– –

YES

– –

YES

– –

YES YES*⁹

71.2

72.0

66.0

76.0

76.1

60.0

75.1

78.1

61.8

71.7

81.1

49.7

63.9

Work Station (HP)

Work Station

(SUN)

YES*⁹

YES

1280

1024

YES

1152

900

C Sync

– –

C Sync

– –

YES

YES*³

YES

YES YES*⁹

– –

1280

1024

768

1280

1024

– –

YES*²1024

768 YES YES*⁹

YES 1280

1024 YES YES*⁹

Work Station

(SGI)

YES

YES*³

– –

IDC-3000G

PAL625P

YES*⁶YES*⁶

– –

NO YES*⁹

768

576

50.0

59.9

31.4

31.5

NEG

YES

640

480

525P

NTSC525P

*1 Only when using a graphic accelerator board that is capable of displaying 852

480.

*2 The picture is displayed in the original resolution. The picture will be compressed for other signals.

*3 Aspect ratio is 5:4. This signal is converted to a 720 dots

768 lines signal.

*4 Normally the RGB select mode suite for the input signals is set automatically. If the picture is not displayed properly, set the

RGB mode prepared for the input signals listed in the table above.

*5 To connect the monitor to Macintosh computer, use the monitor adapter (D-Sub 15-pin) to your computer's video port.

*6 Other screen modes (ZOOM and STADIUM) are available as well.

*7 CVT standard compliant.

*8 Analog signal is not available.

*9 The text cannot be displayed at the “RIGHT” and “LEFT” location.

NOTE:

• While the input signals comply with the resolution listed in the table above, you may have to adjust the position and size of the

picture or the fine picture because of errors in synchronization of your computer.

• This monitor has a resolution of 1024 dots

768 lines. It is recommended that the input signal should be XGA, wide XGA, or

equivalent.

• With digital input some signals are not accepted.

• The sync may be disturbed when a nonstandard signal other than the aforementioned is input.

• If you are connecting a composite sync signal, use the HD terminal.

What is HDCP/HDCP technology?

HDCP is an acronym for High-bandwidth Digital Content Protection. High bandwidth Digital Content Protection (HDCP) is a

system for preventing illegal copying of video data sent over a Digital Visual Interface (DVI).

If you are unable to view material via the DVI input, this does not necessarily mean the PDP is not functioning properly. With

the implementation of HDCP, there may be cases in which certain content is protected with HDCP and might not be displayed

due to the decision/intention of the HDCP community (Digital Content Protection, LLC).

• “IBM PC/AT” and “XGA” are registered trademarks of International Business Machines, Inc. of the United States.

• “Apple Macintosh” is a registered trademark of Apple Computer, Inc. of the United States.

En-42

Supported resolution (50XM6/60XM5)

•

When the screen mode is NORMAL, each signal is converted to a 1024 dots

768 lines signal. (Except for *^{2, 3}

When the screen mode is TRUE, the picture is displayed in the original resolution.

)

When the screen mode is FULL, each signal is converted to a 1365 dots

768 lines signal. (Except for *²)

Computer input signals supported by this system

Sync Polarity

Horizontal Vertical Horizontal Vertical

Presence

Screen mode

NORMAL TRUE FULL

Vertical

Horizontal

frequency frequency

(Hz)

(kHz)

70.1

31.5

RGB

TEXT

INSERT

Dots

lines

Model

Signal Type

select*⁴

DVI

Memory

(4:3)

– –

(16:9)

YES

YES*²

YES

NEC PC-9800

640

400

720

400

640

480

– –

720

400

640

480

– –

YES

– –

YES

NEG

POS

NEG

POS

NEG

POS

NEG

POS

NEG

POS

NEG

POS

NEG

POS

NEG

POS

NEG

POS

NEG

POS

NEG

POS

NEG

POS

NEG

POS

NEG

POS

YES

– –

YES

– –

YES

70.1

59.9

72.8

75.0

85.0

100.4

120.4

85.1

60.0

56.3

60.3

72.2

75.0

85.1

99.8

120.0

60.0

70.1

75.0

85.0

100.6

119.4

75.0

60.0

72.0

56.2

59.8

69.8

59.8

60.0

85.0

60.0

59.9

60.0

75.0

85.0

100.1

60.0

74.9

85.0

60.0

65.0

70.0

75.0

85.0

50.0

60.0

59.9

60.0

66.7

74.6

74.9

75.1

59.9

31.5

37.9

37.5

43.3

51.1

61.3

37.9

31.0

31.7

35.2

37.9

48.1

46.9

53.7

63.0

75.7

48.4

56.5

60.0

68.7

80.5

95.5

67.5

53.7

64.9

45.1

48.0

56.0

49.7

53.1

60.0

85.9

47.7

48.3

64.0

80.0

91.1

108.5

65.3

82.3

93.9

65.3

75.0

81.3

87.5

93.8

106.3

56.2

67.5

74.6

74.0

35.0

49.7

60.2

68.7

55.9

– –

YES

– –

YES

– –

YES

– –

YES

– –

131

111

110

YES

– –

YES

720

400

848

480

852

480*¹

800

600

– –

YES

848

480

852

480

– –

YES

– –

YES

800

600 YES

YES

YES*²

YES

– –

YES

– –

YES

IBM PC/AT

compatible

computers

1024

768 YES

1024

768

YES

1024

768

1024

768

– –

YES

– –

YES

– –

YES

– –

YES

– –

YES*⁹

YES

– –

1152

864 YES

1152

864

– –

1152

864

YES

– –

YES

– –

YES

1280

768 NO

1280

768

– –

YES

1280

768

YES

– –

YES

1280

768

– –

YES

1280

800*⁷

1280

854

1280

960

1280

800 YES

– –

YES

1280

854 YES

– –

YES

– –

YES

– –

YES

YES*⁹

– –

1360

765 NO

1360

768 YES

1376

768 YES

1280

1024 YES

1360

765

1360

768

1376

768

1280

1024

– –

YES

– –

YES

– –

YES

YES*³

YES

– –

YES

– –

YES*⁹

YES

– –

YES

– –

1400

1050*⁷

1400

1050 YES

– –

YES

– –

1680

1050*⁷

1680

1050 YES

– –

1600

1200 YES

1600

1200

YES

– –

1920

1080*⁸

1920

1080 YES

1920

1080 YES

1920

1200 – –

– –

1920

1200*⁷

– –

YES

1920

1200RB

1920

1200RB

640

480

832

624

– –

YES

YES*²

YES

– –

YES

– –

Sync on G Sync on G

Apple

Macintosh*⁵

YES

– –

1024

768

1152

870

1440

900*⁷

YES

– –

YES

– –

YES

– –

YES

NEG

POS

YES

En-43

Screen mode

NORMAL TRUE FULL select*⁴

Sync Polarity

Horizontal Vertical Horizontal Vertical

Presence

Vertical

Horizontal

frequency frequency

(Hz) (kHz)

60.0 64.6

RGB

TEXT

INSERT

Dots

lines

Model

DVI

Memory

Signal Type

(4:3)

YES*³

YES

(16:9)

– –

YES 1280

1024 YES YES*⁹

1280

1024

Work Station

(EWS4800)

NEG

– –

NEG

– –

YES

– –

YES

– –

YES

– –

YES YES*⁹

71.2

72.0

66.0

76.0

76.1

60.0

75.1

78.1

61.8

71.7

81.1

49.7

63.9

Work Station (HP)

Work Station

(SUN)

1280

1024

YES

YES YES*⁹

1152

900

C Sync

– –

C Sync

– –

YES

– –

YES*³

YES*²

YES*³

1280

1024

768

1280

1024

– –

YES 1024

768 YES YES*⁹

Work Station

(SGI)

– –

YES 1280

1024 YES YES*⁹

– –

IDC-3000G

PAL625P

YES*⁶

– –

YES*⁶

– –

NO YES*⁹

768

576

50.0

59.9

31.4

31.5

NEG

YES

640

480

525P

NTSC525P

*1 Only when using a graphic accelerator board that is capable of displaying 852

480.

*2 The picture is displayed in the original resolution.

*3 The aspect ratio is 5:4. This signal is converted to a 960 dots

768 lines signal.

*4 Normally the RGB select mode suite for the input signals is set automatically. If the picture is not displayed properly, set the

RGB mode prepared for the input signals listed in the table above.

*5 To connect the monitor to Macintosh computer, use the monitor adapter (D-Sub 15-pin) to your computer's video port.

*6 Other screen modes (ZOOM and STADIUM) are available as well.

*7 CVT standard compliant.

*8 Analog signal is not available.

*9 The text cannot be displayed at the “RIGHT” and “LEFT” location.

NOTE:

• While the input signals comply with the resolution listed in the table above, you may have to adjust the position and size of the

picture or the fine picture because of errors in synchronization of your computer.

• When a 1280 dots

1024 lines signal or 1600 dots

1200 lines signal is input to the monitor, the picture will be compressed.

• This monitor has a resolution of 1365 dots

768 lines. It is recommended that the input signal should be XGA, wide XGA,

or equivalent.

• With digital input some signals are not accepted.

• The sync may be disturbed when a nonstandard signal other than the aforementioned is input.

• If you are connecting a composite sync signal, use the HD terminal.

What is HDCP/HDCP technology?

HDCP is an acronym for High-bandwidth Digital Content Protection. High bandwidth Digital Content Protection (HDCP) is a

system for preventing illegal copying of video data sent over a Digital Visual Interface (DVI).

If you are unable to view material via the DVI input, this does not necessarily mean the PDP is not functioning properly. With

the implementation of HDCP, there may be cases in which certain content is protected with HDCP and might not be displayed

due to the decision/intention of the HDCP community (Digital Content Protection, LLC).

• “IBM PC/AT” and “XGA” are registered trademarks of International Business Machines, Inc. of the United States.

• “Apple Macintosh” is a registered trademark of Apple Computer, Inc. of the United States.

En-44

Specifications

Ⅵ 42XM5

Screen Size

40.4

(1.59")

921.6 mm(H)

515.3 mm(V)

36.3 inches(H)

20.3 inches(V)

diagonal 42 inches

57.6

(2.31")

1022 (40.2")

Aspect Ratio

Resolution

Pixel Pitch

16 : 9

921.6 (36.3")

1024 pixels(H)

768 pixels(V)

0.9 mm(H)

0.671 mm(V)

0.036 inches(H)

0.027 inches(V)

Signals

Synchronization Range Horizontal : 15.5 kHz to 110.0 kHz

(automatic : step scan)

Vertical : 50.0 Hz to 120.0 Hz

(automatic : step scan)

(3.9")

Input Signals

RGB, NTSC (3.58/4.43), PAL (B,G,M,N),

PAL60, SECAM, HD*¹, DVD*¹, DTV*¹

Units are in mm

(inch)

Input Terminals (VIDEO1 and RGB1 can also be used as OUTPUT terminals)

RGB

The features and specifications may be subject to change without

notice.

*¹HD/DVD/DTV input signals supported on this system.

Visual 1 (Analog) mini D-sub 15-pin

Visual 2 (Analog) BNC (R, G, B, HD, DV)

1*²

Visual 3 (Digital) DVI-D 24-pin

1*³

480P (60 Hz)

525I (60 Hz)

625P (50 Hz)

720P (50 Hz)

1080I (60 Hz)

480I (60 Hz)

576P (50 Hz)

625I (50 Hz)

1035I (60 Hz)

1080P (50 Hz)

525P (60 Hz)

576I (50 Hz)

720P (60 Hz)

1080I (50 Hz)

1080P (60 Hz)

Video

Visual 1

Visual 2

Visual 3

BNC

RCA-pin

S-Video: DIN 4-pin

*²The 5-BNC connectors are used as RGB2 and DVD/HD2 input.

Select one of them under “BNC INPUT”.

*³Compatible with HDCP.

DVD/HD

Visual 1

Visual 2

Visual 3

RCA-pin (Y, Cb/Pb, Cr/Pr)

1*¹

BNC (Y, Cb/Pb, Cr/Pr)

1*^1,*²

DVI-D 24-pin

1*³

Supported Signals

• 640

480P @ 59.94/60 Hz

• 720

480P @ 59.94/60 Hz

• 720

576P @ 50 Hz

• 1280

720P @ 59.94/60 Hz

• 1280

720P @ 50 Hz

• 1440 (720)

480I @ 59.94/60 Hz

• 1440 (720)

576I @ 50 Hz

• 1920

1080I @ 59.94/60 Hz

• 1920

1080I @ 50 Hz

Audio

External Control

Remote In

Remote Out

Stereo RCA

3(Selectable)

D-sub 9-pin

1(RS-232C)

Mini jack

Sound output

Power Supply

Current Rating

Power Consumption

8 W+8 W at 6 ohm

• 1920

1080P @ 59.94/60 Hz

• 1920

1080P @ 50 Hz

AC100 V to 240 V 50 Hz/60 Hz

4.5 A (maximum)

Note: In some cases a signal on the plasma monitor may not be displayed

properly. The problem may be an inconsistency with standards from

the source equipment (DVD, Set-top box, etc.). If you do experience

such a problem please contact your dealer and also the manufacturer of

the source equipment.

285 W (typical)

Dimensions

1022 mm(W)

610 mm(H)

98 mm(D)

40.2 inches(W)

24 inches(H)

3.9 inches(D)

Weight

30 kg / 66.1 lbs (without stand)

Environmental Considerations

Operating Temperature 0 °C to 40 °C / 32 °F to 104 °F

Humidity

Storage Temperature -10 °C to 50 °C / 14 °F to 122 °F

Humidity 10 % to 90 % (no condensation)

20 % to 80 % (no condensation)

Other Features Motion compensated 3D Scan Converter (NTSC,

PAL, 480I, 576I, 525I, 625I, 1035I, 1080I), 2-3

pull down Converter (NTSC, 480I, 525I, 1035I,

1080I (60 Hz)), 2-2 pull down Converter (PAL,

576I, 625I, NTSC, 480I, 525I), Digital Zooming

(100 % to 900 % Selectable), Video Wall 4-25

multi screens, Self Diagnosis via RS232C,

Long Life Mode (PEAK BRIGHT, ORBITER,

INVERSE, WHITE, SCREEN WIPER, SOFT

FOCUS, etc.), Control Lock (Except power SW),

Input Skip, Color Tune, Programmable Timer,

Loop Throughout Interface, Plug and play

(DDC1, DDC2b, RGB3: DDC2b only), Enhanced

Split Screen, Protocol Set, etc.

Accessories

Regulations

Power cord (

1), Remote control (

1), AAA

batteries (

2), Manuals (Start up Guide and

CD-ROM), Ferrite cores for power cord (

2),

bands for power code (

2), Cable clampers

(

3), beads bands (

3), Ferrite core for

remote cable (

2).

IEC60950-1, EN60950-1,

EN55022 class B, EN55024,

EN61000-3-2, EN61000-3-3,

AS/NZS CISPR22 class B

En-45

Specifications

Ⅵ 50XM6

Screen Size

(1.5")

1104 mm(H)

621 mm(V)

43.4 inches(H)

24.4 inches(V)

diagonal 50 inches

(2.4")

1222 (48.1")

Aspect Ratio

Resolution

Pixel Pitch

16 : 9

1104 (43.4")

1365 pixels(H)

768 pixels(V)

0.81 mm(H)

0.81 mm(V)

0.032 inches(H)

0.032 inches(V)

Signals

Synchronization Range Horizontal : 15.5 kHz to 110.0 kHz

(automatic : step scan)

Vertical : 50.0 Hz to 120.0 Hz

(automatic : step scan)

(3.9")

Input Signals

RGB, NTSC (3.58/4.43), PAL (B,G,M,N),

PAL60, SECAM, HD*1 , DVD*1 , DTV*1

Units are in mm

(inch)

Input Terminals (VIDEO1 and RGB1 can also be used as OUTPUT terminals)

The features and specifications may be subject to change without

notice.

*¹HD/DVD/DTV input signals supported on this system.

RGB

Visual 1 (Analog) mini D-sub 15-pin

Visual 2 (Analog) BNC (R, G, B, HD, VD)

1*²

Visual 3 (Digital) DVI-D 24-pin

1*³

480P (60 Hz)

525I (60 Hz)

625P (50 Hz)

720P (50 Hz)

1080I (60 Hz)

480I (60 Hz)

576P (50 Hz)

625I (50 Hz)

1035I (60 Hz)

1080P (50 Hz)

525P (60 Hz)

576I (50 Hz)

720P (60 Hz)

1080I (50 Hz)

1080P (60 Hz)

Video

Visual 1

Visual 2

Visual 3

BNC

RCA-pin

S-Video: DIN 4-pin

DVD/HD

*²The 5-BNC connectors are used as RGB2 and DVD/HD2 input.

Select one of them under “BNC INPUT”.

*³Compatible with HDCP.

Visual 1

Visual 2

Visual 3

RCA-pin (Y, Cb/Pb, Cr/Pr)

1*¹

BNC (Y, Cb/Pb, Cr/Pr)

1*^1,*²

DVI-D 24-pin

1*³

Supported Signals

• 640

480P @ 59.94/60 Hz

• 720

480P @ 59.94/60 Hz

• 720

576P @ 50 Hz

• 1280

720P @ 59.94/60 Hz

• 1280

720P @ 50 Hz

• 1440 (720)

480I @ 59.94/60 Hz

• 1440 (720)

576I @ 50 Hz

• 1920

1080I @ 59.94/60 Hz

• 1920

1080I @ 50 Hz

Audio

External Control

Remote In

Remote Out

Stereo RCA

3 (Selectable)

D-sub 9-pin

1 (RS-232C)

Mini jack

Sound output

Power Supply

Current Rating

Power Consumption

9 W+9 W at 6 ohm

• 1920

1080P @ 59.94/60 Hz

• 1920

1080P @ 50 Hz

AC100 V to 240 V 50 Hz/60 Hz

5.0 A (maximum)

Note: In some cases a signal on the plasma monitor may not be displayed

properly. The problem may be an inconsistency with standards from

the source equipment (DVD, Set-top box, etc.). If you do experience

such a problem please contact your dealer and also the manufacturer of

the source equipment.

340 W (typical)

Dimensions

1222 mm(W)

736 mm(H)

99 mm(D)

48.1 inches(W)

29.0 inches(H)

3.9 inches(D)

Weight

41.5 kg / 91.4 lbs (without stand)

Environmental Considerations

Operating Temperature 0 °C to 40 °C / 32 °F to 104 °F

Humidity

Storage Temperature -10 °C to 50 °C / 14 °F to 122 °F

Humidity 10 % to 90 % (no condensation)

20 % to 80 % (no condensation)

Other Features Motion compensated 3D Scan Converter (NTSC,

PAL, 480I, 576I, 525I, 625I, 1035I, 1080I), 2-3

pull down Converter (NTSC, 480I, 525I, 1035I,

1080I (60 Hz)), 2-2 pull down Converter (PAL,

576I, 625I, NTSC, 480I, 525I), Digital Zooming

(100 % to 900 % Selectable), Video Wall 4-25

multi screens, Self Diagnosis via RS232C,

Long Life Mode (PEAK BRIGHT, ORBITER,

INVERSE, WHITE, SCREEN WIPER, SOFT

FOCUS, etc.), Control Lock (Except power SW),

Input Skip, Color Tune, Programmable Timer,

Loop Throughout Interface, Plug and play

(DDC1, DDC2b, RGB3: DDC2b only), Enhanced

Split Screen, Protocol Set, etc.

Accessories

Regulations

Power cord (

1), Remote control (

1), AAA

batteries (

2), Manuals (Start up Guide and

CD-ROM), Ferrite cores for power cord (

2),

bands for power code (

2), Cable clampers

(

3), beads bands (

3), Ferrite core for

remote cable (

2).

IEC60950-1, EN60950-1,

EN55022 class B, EN55024,

EN61000-3-2, EN61000-3-3,

AS/NZS CISPR22 class B

En-46

Specifications

Ⅵ 60XM5

Screen Size

(1.8")

1319 mm(H)

742 mm(V)

51.9 inches(H)

29.2 inches(V)

diagonal 60 inches

(3.0")

1470 (57.9")

Aspect Ratio

Resolution

Pixel Pitch

16 : 9

1319 (51.9")

1365 pixels(H)

768 pixels(V)

0.97 mm(H)

0.97 mm(V)

0.038 inches(H)

0.038 inches(V)

Signals

Synchronization Range Horizontal : 15.5 kHz to 110.0 kHz

(automatic : step scan)

Vertical : 50.0 Hz to 120.0 Hz

(automatic : step scan)

122

(4.8")

Input Signals

RGB, NTSC (3.58/4.43), PAL (B,G,M,N),

PAL60, SECAM, HD*¹, DVD*¹, DTV*¹

Units are in mm

(inch)

Input Terminals (VIDEO1 and RGB1 can also be used as OUTPUT terminals)

The features and specifications may be subject to change without

notice.

*¹HD/DVD/DTV input signals supported on this system.

RGB

Visual 1 (Analog) mini D-sub 15-pin

Visual 2 (Analog) BNC (R, G, B, HD, VD)

1*²

Visual 3 (Digital) DVI-D 24-pin

1*³

480P (60 Hz)

525I (60 Hz)

625P (50 Hz)

720P (50 Hz)

1080I (60 Hz)

480I (60 Hz)

576P (50 Hz)

625I (50 Hz)

1035I (60 Hz)

1080P (50 Hz)

525P (60 Hz)

576I (50 Hz)

720P (60 Hz)

1080I (50 Hz)

1080P (60 Hz)

Video

Visual 1

Visual 2

Visual 3

BNC

RCA-pin

S-Video: DIN 4-pin

DVD/HD

*²The 5-BNC connectors are used as RGB2 and DVD/HD2 input.

Select one of them under “BNC INPUT”.

*³Compatible with HDCP.

Visual 1

Visual 2

Visual 3

RCA-pin (Y, Cb/Pb, Cr/Pr)

1*¹

BNC (Y, Cb/Pb, Cr/Pr)

1*^1,*²

DVI-D 24-pin

1*³

Supported Signals

• 640

480P @ 59.94/60 Hz

• 720

480P @ 59.94/60 Hz

• 720

576P @ 50 Hz

• 1280

720P @ 59.94/60 Hz

• 1280

720P @ 50 Hz

• 1440 (720)

480I @ 59.94/60 Hz

• 1440 (720)

576I @ 50 Hz

• 1920

1080I @ 59.94/60 Hz

• 1920

1080I @ 50 Hz

Audio

External Control

Remote In

Remote Out

Stereo RCA

3 (Selectable)

D-sub 9-pin

1 (RS-232C)

Mini jack

Sound output

Power Supply

Current Rating

Power Consumption

9 W+9 W at 6 ohm

• 1920

1080P @ 59.94/60 Hz

• 1920

1080P @ 50 Hz

AC100 V to 240 V 50 Hz/60 Hz

7.0 A (maximum)

Note: In some cases a signal on the plasma monitor may not be displayed

properly. The problem may be an inconsistency with standards from

the source equipment (DVD, Set-top box, etc.). If you do experience

such a problem please contact your dealer and also the manufacturer of

the source equipment.

440 W (typical)

Dimensions

1470 mm(W)

880 mm(H)

122 mm(D)

57.9 inches(W)

34.7 inches(H)

4.8 inches(D)

Weight

61.5 kg / 135.6 lbs (without stand)

Environmental Considerations

Operating Temperature 0 °C to 40 °C / 32 °F to 104 °F

Humidity

Storage Temperature -10 °C to 50 °C / 14 °F to 122 °F

Humidity 10 % to 90 % (no condensation)

20 % to 80 % (no condensation)

Other Features Motion compensated 3D Scan Converter (NTSC,

PAL, 480I, 576I, 525I, 625I, 1035I, 1080I), 2-3

pull down Converter (NTSC, 480I, 525I, 1035I,

1080I (60 Hz)), 2-2 pull down Converter (PAL,

576I, 625I, NTSC, 480I, 525I), Digital Zooming

(100 % to 900 % Selectable), Video Wall 4-25

multi screens, Self Diagnosis via RS232C,

Long Life Mode (PEAK BRIGHT, ORBITER,

INVERSE, WHITE, SCREEN WIPER, SOFT

FOCUS, etc.), Control Lock (Except power SW),

Input Skip, Color Tune, Programmable Timer,

Loop Throughout Interface, Plug and play

(DDC1, DDC2b, RGB3: DDC2b only), Enhanced

Split Screen, Protocol Set, etc.

Accessories

Regulations

Power cord (

1), Remote control (

1), AAA

batteries (

2), Manuals (Start up Guide and

CD-ROM), Ferrite cores for power cord (

2),

bands for power code (

2), Cable clampers

(

3), beads bands (

3), Ferrite core for

remote cable (

2).

IEC60950-1, EN60950-1,

EN55022 class B, EN55024,

EN61000-3-2, EN61000-3-3,

AS/NZS CISPR22 class B

En-47

HP Hewlett Packard PX850AA#ABA User Manual
IBM Rack Mount Industrial Monitor HIS RL17 User Manual
Iiyama Computer Monitor E1706S User Manual
KitchenAid Cooktop KGCC505H User Manual
Motorola L803 Cordless Phone L803 User Manual
NEC AccuSync LCD52V User Manual
Panasonic Cordless Telephone KXTG7875S User Manual
Philips 25HT3312 User Manual
Philips 28GR9970 User Manual
Philips DVP3670 User Manual