Motorola MVME5100 Series User Manual

M V M E 5 1 0 0 S e r i e s  
TM  
V M E P r o c e s s o r M o d u l e s  
PowerPC 7400 or PowerPC 750  
microprocessor with 32KB/32KB L1 cache  
Up to 2MB of secondary backside cache  
100 MHz front-side bus  
64MB, 128MB, or 512MB of on-board  
ECC SDRAM—expandable up to 1GB  
with optional RAM500 memory expansion  
modules  
Up to 17MB Flash memory  
Dual IEEE P1386.1 compatible 32/64-bit  
PMC expansion slots  
64-bit PCI expansion mezzanine  
connector allowing up to four more PMCs  
Dual 16550 compatible async serial ports  
Dual 10BaseT/100BaseTX Ethernet  
32KB NVRAM and time-of-day clock with  
replaceable battery backup  
Four 32-bit timers, one watchdog timer  
On-board debug monitor  
Single VME slot even when fully  
configured with two PMC modules and  
both add-on memory mezzanines  
Supercomputing levels of performance in a scalable, single-board  
computer  
The MVME5100 is a high-performance VME processor module featuring the  
Motorola Computer Group (MCG) PowerPlus II architecture with a choice of  
®
PowerPC processors—either Motorola’s MPC7400 with AltiVec technol-  
ogy for algorithmic-intensive computations or the low-power MPC750.  
Based on an integrated PCI bridge–memory controller ASIC designed by  
MCG, PowerPlus II takes memory performance to new levels with 582MB/s  
memory read bandwidth and 640MB/s burst write bandwidth. Plus, Power-  
Plus II architecture supports full PCI throughput of 264MB/s without starving  
the CPU from its memory.  
The MVME5100 is designed to meet the needs of OEMs servicing the military  
and aerospace, industrial automation, and semiconductor process equipment  
market segments.  
face signals to the MVME712M transition module. The 3-row  
P2 adapter can be used for 8-bit SCSI.  
Flash Memory  
Type:  
EEPROM, on-board programmable  
Capacity:  
1MB via two 32-pin PLCC/CLCC sockets;  
16MB surface mount  
To gain access to the additional user definable I/O pins pro-  
vided via the 5-row VME64 extension connector, a special P2  
adapter board is available. This adapter panel replaces the  
traditional 3-row P2 adapter and extends its capability by pro-  
viding access to the PMC I/O pins.  
Read Access (16MB  
port):  
70 clocks (32-byte burst)  
Read Access (1MB  
port):  
262 clocks (32-byte burst)  
NVRAM  
S o f t w a r e S u p p o r t  
Capacity:  
Cell Storage Life:  
Cell Capacity Life:  
Removable Battery:  
32KB (4KB available for users)  
50 years at 55° C  
5 years at 100% duty cycle, 25° C  
Yes  
Firmware Monitor  
Firmware must fulfill the traditional functions of test and initial-  
ization and provide operating system boot support. The  
MVME5100 firmware monitor exceeds these requirements  
with a proven monitor from the embedded VME leader. It  
expands features like power-up tests with extensive diagnos-  
tics, as well as a powerful evaluation and debug tool for sim-  
ple checkout or when high-level development debuggers  
require additional support. All this is included with the  
MVME5100 firmware; plus it supports booting both operating  
systems and kernels.  
Counters/Timers  
TOD Clock Device:  
M48T37V  
Real-Time Timers/  
Counters:  
Four, 32-bit programmable  
Watchdog Timer:  
Time-out generates reset  
VMEbus ANSI/VITA 1-1994 VME64 (IEEE STD 1014)  
Controller:  
DTB Master:  
DTB Slave:  
Arbiter:  
Tundra Universe  
A16–A32; D08–D64, BLT  
A24–A32; D08–D64, BLT, UAT  
RR/PRI  
Operating Systems and Kernels  
MVME5100 supports booting a variety of operating systems  
including a complete range of real-time operating systems  
and kernels which may be purchased from the following com-  
Interrupt Handler/  
Generator:  
IRQ 1–7/Any one of seven IRQs  
System Controller:  
Location Monitor:  
Yes, jumperable or auto detect  
Two, LMA32  
panies:  
®
Wind River Systems, Inc.:  
Multiple Partners:  
VxWorks  
Ethernet Interface  
®
Controller:  
Linux  
Two Intel 82559ER  
10/100Mb/s  
Interface Speed:  
PCI Local bus DMA:  
Connector:  
S p e c i f i c a t i o n s  
Yes, with PCI burst  
One routed to front panel RJ-45, one  
routed to front panel RJ-45 or optionally  
routed to P2, RJ-45 on MVME761  
M V M E 5 1 0 0 P r o c e s s o r M o d u l e  
Asynchronous Serial Ports  
Controller:  
Processor  
16C550C UART  
Microprocessor:  
MPC7400  
400 MHz  
MPC750  
450 MHz  
32K/32K  
1MB  
Number of Ports:  
Configuration:  
Two, 16550 compatible  
EIA-574 DTE  
Clock Frequency:  
On-chip Cache (I/D):  
Secondary Cache:  
32K/32K  
Async Baud Rate, bps  
max.:  
38.4K EIA-232, 115Kbps raw  
1MB or 2MB  
Connector:  
One routed to front panel RJ-45, one on  
planar for development use  
Main Memory  
Type:  
PC100 ECC SDRAM with 100 MHz bus  
Dual IEEE P1386.1 PCI Mezzanine Card Slots  
Capacity:  
64MB, 128MB, or 512MB on board,  
expandable to 1GB with RAM500 mem-  
ory mezzanines  
Address/Data:  
A32/D32/D64, PMC PN1, PN2, PN3,  
PN4 connectors  
PCI Bus Clock:  
Signaling:  
Power:  
33 MHz  
5V  
Single Cycle Accesses:  
Read Burst Mode:  
Write Burst Mode:  
Architecture:  
10 Read/5 Write  
7-1-1-1 idle; 2-1-1-1 aligned page hit  
4-1-1-1 idle; 2-1-1-1 aligned page hit  
64-bit, single interleave  
+3.3V, +5V, ±12V; 7.5 watts maximum  
per PMC slot  
Module Types:  
Two single-wide or one double-wide, front  
panel or P2 I/O  
     
PCI Expansion Connector  
Parallel Port  
Address/Data:  
PCI Bus Clock:  
Signaling:  
Controller:  
A32/D32/D64  
33 MHz  
5V  
PC97307  
Configuration:  
8-bit bi-directional, full IEEE 1284 sup-  
port; Centronics compatible (minus EPP  
and ECP on MVME712M)  
Connector:  
114-pin connector located on the planar  
of the MVME5100  
Modes:  
Master only  
Power Requirements  
(additional power load placed on MVME5100 with IPMC installed)  
Power Requirements  
(not including power required by PMC or IMPC modules)  
IPMC761  
IPMC712  
+5V ± 5%  
+12V ± 10%  
8.0 mA typ.  
–12V ± 10%  
2.0 mA typ.  
+5V:  
0.5 A max.  
0.75 A max.  
0.5 A max.  
0.75 A max.  
MVME5100:  
3.0 A typ.  
+3.3V  
MVME5100 with  
MVME761:  
3.2 A typ.,  
4.0 A max.  
0.2 A typ.  
0.5 A max.  
0.1 A typ.  
0.3 A max.  
T r a n s i t i o n M o d u l e s  
Board Size  
Height:  
Depth:  
233.4 mm (9.2 in.)  
I/O Connectors  
160.0 mm (6.3 in.)  
261.8 mm (10.3 in.)  
19.8 mm (0.8 in.)  
14.8 mm (0.58 in.)  
MVME761  
MVME712M  
Front Panel Height:  
Width:  
Asynchronous  
Serial Ports:  
Two, DB-9 labeled as  
COM1 and COM2  
Three, DB-25 labeled  
as Serial 1, Serial 2,  
and Serial 3  
Max. Component  
Height:  
Synchronous  
Serial Ports:  
Two HD-26 labeled as One, DB-25 labeled as  
I P M C M o d u l e s  
Serial 3 and Serial 4  
(user configurable via  
installation of SIMs),  
Two 60-pin connectors  
on MVME761 planar  
for installation of two  
SIMs  
Serial 4  
PMC Interface  
Address/Data:  
A32/D32/D64, PMC PN1, PN2, PN3,  
PN4 connectors  
PCI Bus Clock:  
Signaling:  
33 MHz  
Parallel Port:  
Ethernet:  
SCSI:  
HD-36, Centronics  
compatible  
D-36, Centronics com-  
patible  
5V  
Module Type:  
Basic, single-wide; P2 I/O  
10BaseT or  
100BaseTX, RJ-45  
not available  
SCSI Bus  
8- or 16-bit, 50- or 68-  
pin connector via P2  
adapter  
8-bit, standard SCSI D-  
50  
Controller:  
Symbios 53C895A  
Yes, with PCI local bus burst  
5.0MB/s  
PCI Local Bus DMA:  
Asynchronous (8-bit  
mode):  
Board Size  
Height:  
233.4 mm (9.2 in.)  
80.0 mm (3.1 in.)  
Ultra SCSI:  
20.0MB/s (8-bit mode), 40.0MB/s (16-bit  
mode)  
Depth:  
Front Panel Height:  
Front Panel Width:  
261.8 mm (10.3 in.)  
Note: 16-bit SCSI operation precludes the use of some PMC Slot 2  
signals.  
MVME761: 19.8 mm (0.8 in.)  
MVME712M: 39.6 mm (1.6 in.)  
Synchronous Serial Ports  
Controller:  
Number of Ports:  
Configuration:  
A l l M o d u l e s  
85230/8536  
Two (IPMC761); one (IPMC712)  
IPMC761: TTL to P2 (both ports), SIM  
configurable on MVME761;  
IPMC712: EIA-232 to P2  
Environmental  
(Minimum of 400 LFM (linear feet per minute) of forced air cooling is  
recommended for operation in the higher temperature ranges.)  
Baud Rate, bps max.:  
2.5M sync, 38.4K async  
10 MHz/5 MHz  
Operating  
Nonoperating  
Oscillator Clock Rate  
(PCLK):  
Temperature:  
0° C to +55° C  
(inlet air temp. w/forced  
air cooling)  
–40° C to +85° C  
Asynchronous Serial Ports  
Controller:  
Number of Ports:  
Configuration:  
16C550 UART; 85230/8536  
Humidity (NC):  
Vibration:  
5% to 90%  
5% to 90%  
Two (IPMC761); three (IPMC712)  
2 Gs RMS,  
20–2000 Hz random  
6 Gs RMS,  
20–2000 Hz random  
EIA-574 DTE (IPMC761);  
EIA-232 (IPMC712)  
Async Baud Rate, bps  
max.:  
38.4K EIA-232, 115Kbps raw  
     
Demonstrated MTBF  
MVME761 Compatible I/O  
(based on a sample of eight boards in accelerated stress environ-  
ment; results pending for IPMC712)  
IPMC761-001  
Multifunction rear I/O PMC module; Ultra  
Wide SCSI, one parallel port, two async and  
two sync/async serial ports  
Mean:  
190,509 hours  
107,681 hours  
95% Confidence:  
MVME761-001  
Transition module: Two DB-9 async serial port  
connectors, two HD-26 sync/async serial port  
connectors, one HD-36 parallel port connec-  
tor, one RJ-45 10/100 Ethernet connector;  
includes 3-row DIN P2 adapter module and  
cable (for 8-bit SCSI)  
Safety  
All printed wiring boards (PWBs) are manufactured with a flammabil-  
ity rating of 94V-0 by UL recognized manufacturers.  
Electromagnetic Compatibility (EMC)  
Intended for use in systems meeting the following regulations:  
MVME761-011  
Transition module: Two DB-9 async serial port  
connectors, two HD-26 sync/async serial port  
connectors, one HD-36 parallel port connec-  
tor, and one RJ-45 10/100 Ethernet connec-  
tor; includes 5-row DIN P2 adapter module  
and cable (for 16-bit SCSI); requires back-  
plane with 5-row DIN connectors  
U.S.:  
FCC Part 15, Subpart B, Class A (non-residential)  
Canada:  
ICES-003, Class A (non-residential)  
This product was tested in a representative system to the following  
standards:  
CE Mark per European EMC Directive 89/336/EEC with Amend-  
ments; Emissions: EN55022 Class B; Immunity: EN55024  
(results pending for configurations with IPMC712)  
SIM232DCE or DTE  
SIM530DCE or DTE  
SIMV35DCE or DTE  
SIMX21DCE or DTE  
EIA-232 DCE or DTE Serial Interface Module  
EIA-530 DCE or DTE Serial Interface Module  
V.35 DCE or DTE Module  
O r d e r i n g I n f o r m a t i o n  
X.21 DCE or DTE Serial Interface Module  
Related Products  
All models of the MVME5100 are available with either VME Scanbe  
front panel (-01x1) or IEEE 1101 compatible front panel (-01x3).  
PMCSPAN-002  
Primary 32-bit PCI expansion, mates directly  
to the MVME5100 providing slots for either  
two single-wide or one double-wide PMC  
cards; optional PMCSPAN-010  
Part Number  
Description  
MPC750 configurations with 450 MHz MPC750, 17MB Flash and  
1MB L2 cache  
PMCSPAN-010  
Secondary 32-bit PCI expansion, plugs  
directly into PMCSPAN-002 providing two  
additional PMC slots  
MVME5100-013x  
MVME5100-016x  
64MB ECC SDRAM  
512MB ECC SDRAM  
MPC7400 configurations with 400 MHz MPC7400 and 17MB Flash  
RAM500-004  
RAM500-006  
RAM500-016  
Stackable (top) 64MB ECC SDRAM mezza-  
nine  
MVME5101-013x  
MVME5101-016x  
MVME5101-213x  
MVME5101-214x  
MVME5101-216x  
64MB ECC SDRAM, 1MB L2 cache  
512MB ECC SDRAM, 1MB L2 cache  
64MB ECC SDRAM, 2MB L2 cache  
128MB ECC SDRAM, 2MB L2 cache  
512MB ECC SDRAM, 2MB L2 cache  
Stackable (top) 256MB ECC SDRAM mezza-  
nine  
Stackable (bottom) 256MB ECC SDRAM  
mezzanine  
Documentation  
I/O Modules  
MVME712M Compatible I/O  
V5100A/IH  
MVME5100 Installation and Use  
V5100A/PG  
VME761A/IH  
Programmer’s Reference Guide  
IPMC712-001  
Multifunction rear I/O PMC module; Ultra  
Wide SCSI, one parallel port, three async and  
one sync/async serial ports  
MVME761 Transition Module Installation and  
Use  
VME712MA/IH  
MVME712 Transition Module Installation and  
Use  
MVME712M  
Transition module connectors: One DB-25  
sync/async serial port, three DB-25 async  
serial port, one AUI connector, one D-36 par-  
allel port, and one 50-pin 8-bit SCSI; includes  
3-row DIN P2 adapter module and cable  
PPCBUGA1/UM  
PPCBUGA2/UM  
PPCBug Firmware Package User’s Manual  
(volumes one and two)  
PPCDIAA/UM  
PPCBug Diagnostics Manual  
Documentation is available for online viewing and ordering at http://  
Motorola Computer Group Worldwide Headquarters: 2900 S. Diablo Way, Tempe, AZ 85282  
Sales Offices: United Kingdom: +44 (0) 1256 790555 • Asia Pacific and Japan: 852-2966-3210 • France: +33 (0) 1 64  
86 64 24 • Germany: +49 (0) 611-3611 604 • East Mediterranean: 972-3-568-4388 • Canada & Central Pan America:  
905-507-7200 • Eastern Pan America: 508-357-8260 • Western Pan America: 408-991-8634  
Motorola and the stylized M logo are registered trademarks and the Intelligence Everywhere logo, AltiVec, Digital DNA and the Digital DNA logo are trademarks of Motorola, Inc. PowerPC and  
the PowerPC logo are registered trademarks and PowerPC 750 is a trademark of International Business Machines Corporation and are used by Motorola, Inc. under license from International  
Business Machines Corporation. VxWorks is a registered trademark of Wind River Systems, Inc. Linux is a registered trademark of Linus Torvalds. Centronics is a registered trademark of  
Centronics Data Computer Corporation. All other product or service names are the property of their respective owners.  
This datasheet identifies products, their specifications, and their characteristics, which may be suitable for certain applications. It does not constitute an offer to sell or a commitment of present  
or future availability, and should not be relied upon to state the terms and conditions, including warranties and disclaimers thereof, on which Motorola may sell products. A prospective buyer  
should exercise its own independent judgement to confirm the suitability of the products for particular applications. Motorola reserves the right to make changes, without notice, to any products  
or information herein which will, in its sole discretion, improve reliability, function, or design. Motorola does not assume any liability arising out of the application or use of any product or circuit  
described herein; neither does it convey any license under its patent or other intellectual property rights or under others. This disclaimer extends to any prospective buyer, and it includes  
Motorola’s licensee, licensee’s transferees, and licensee’s customers and users. Availability of some of the products and services described herein may be restricted in some locations.  
® Reg. U.S. Pat. & Tm. Off.  
© 1999, 2000, 2001 Motorola, Inc. All rights reserved. M5100-D8 9/01  
 

LG Electronics LG Life Good Computer Monitor L1760TQ User Manual
Luce LS328 User Manual
Palsonic DVDR313 User Manual
Philips 21PT3005 User Manual
Philips 29PT8857 User Manual
Philips 30PW8402 User Manual
Philips 9125 User Manual
Philips DVP5992 User Manual
Philips MDV456 User Manual
Philips PT 7007 User Manual