Moffat TURBOFAN E20M User Manual

2
20MSERIES  
E20M Series  
(Manual Operation)  
Installation and Operation Manual  
234090-1  
Contents List  
E20M Series Turbofan Convection Ovens.  
Model Numbers Covered in this Manual  
E22M3 - Turbofan Oven - 3 Tray Convection Oven.  
E23M3 - Turbofan Oven - 3 Tray Convection Oven.  
E27M2 - Turbofan Oven - 2 Tray Convection Oven.  
E27M3 - Turbofan Oven - 3 Tray Convection Oven.  
E28M4 - Turbofan Oven - 4 Tray Convection Oven.  
Introduction........................................................................................................... 2  
Safety Information  
Specifications......................................................................................................... 3  
Installation............................................................................................................. 4  
Installation Requirements  
Unpacking  
Location  
Clearances  
Stand Mounted Ovens  
Electrical Connection  
Positioning and Levelling of Oven  
Initial Start-Up  
Operation ............................................................................................................... 6  
Operation Guide  
Oven Control Panel  
Description of Controls  
Using the Oven  
Cleaning ................................................................................................................. 7  
Cleaning Guidelines  
Oven Cleaning  
Fault Finding ........................................................................................................ 10  
Electrical Schematics ........................................................................................... 11  
Replacement Parts List ........................................................................................ 13  
Introduction  
Before using your new oven, please read this instruction  
This manual must be kept by the owner for future  
reference.  
manual carefully, pay particular attention to any information  
labelled ‘WARNING’, ‘CAUTION’, ‘IMPORTANT’ or  
‘NOTE’ in this manual.  
A record of the Date of Purchase, Date of Installation  
and Serial Number of the oven should be recorded in  
the area provided below.  
The serial number of this oven can be found on the  
Technical Data Plate located on the front right hand  
side panel, see diagram in ‘Installation Section’.  
Indicates a hazardous situation  
which, if not avoided, will result in  
death or serious injury.  
Warning  
Caution  
Indicates a hazardous situation  
which, if not avoided, will result in  
minor or moderate injury.  
Model Number:  
Serial Number:  
Dealer:  
If you are unsure of any aspect of the installation,  
instructions or performance of your oven, contact your  
TURBOFAN dealer promptly. In many cases a phone call  
could answer your question.  
Service Provider:  
Should you contact your TURBOFAN dealer on any matter  
concerning this oven, please have the information provided  
opposite, readily available.  
Date Purchased:  
Date Installed:  
Safety Information  
For your safety, please pay attention to the following symbols  
marked on the appliance.  
- Risk of electric shock.  
No user serviceable parts inside.  
Qualified service person access only.  
Disconnect from power before servicing.  
2
Specifications  
E22M3  
E23M3  
E27M2 / E27M3  
E28M4  
Oven Tray Details  
Oven Power Ratings  
Tray Capacity  
Tray Spacing  
3 x EN 2/3 Tray  
3 x US ½ Pan  
110-120V, 1P+N+E, 60HZ, 1.5 kW  
220-240V, 1P+N+E, 50/60HZ, 2.0 kW  
70 mm / 2 3/4”  
E22M3  
E23M3  
E22M3  
E23M3  
208V,  
220V,  
1P+N+E, 50-60 HZ, 2.7 kW  
1P+N+E, 50-60 HZ, 3.0 kW  
3 x EN 2/3 Tray  
3 x US ½ Pan  
85 mm / 3 1/3”  
230-240V, 1P+N+E, 50-60 HZ, 3.0 kW  
208V,  
220V,  
1P+N+E, 50-60HZ, 2.7kW  
1P+N+E, 50-60HZ, 3.0kW  
3 x EN 600 x 400 mm Tray  
3 x US Full Pan  
85 mm / 3 1/3”  
85 mm / 3 1/3”  
76 mm / 3 ”  
E27M2  
E27M3  
E28M4  
E27M2  
E27M3  
E28M4  
230-240V, 1P+N+E, 50-60HZ, 3.0kW  
208V,  
220V,  
1P+N+E, 50-60HZ, 4.2kW  
1P+N+E, 50-60HZ, 4.7kW  
3 x EN 600 x 400 mm Tray  
3 x US Full Pan  
230-240V, 1P+N+E, 50-60HZ, 4.7kW  
208V,  
220V,  
1P+N+E, 50-60HZ, 5.4kW  
1P+N+E, 50-60HZ, 6.0kW  
4 x EN 600 x 400 mm Tray  
4 x US Full Pan  
230-240V, 1P+N+E, 50-60HZ, 6.0kW  
3
Installation  
Installation Requirements  
Important:  
Installation shall comply with local electrical, health and safety requirements.  
It is most important that this oven is installed correctly and that oven operation is correct before use.  
If you have any questions regarding the proper installation and / or operation of this oven, please contact your local  
Turbofan distributor.  
Electrical Power  
Rating  
Oven  
Serial Number  
Oven  
Model Number  
Current Draw  
MOFFAT LIMITED  
)
MODEL  
CODE  
SERIAL  
LOT  
E22M3  
USE22M3  
xxxxxx  
CHRISTCHURCH  
(
NEW ZEALAND  
yywwxxx  
*******  
A @  
V a.c.  
115  
12.0  
110-120 V a.c. 50-60 Hz  
1.5 kW  
1P+N+E  
THIS APPLIANCE MUST BE EARTHED / GROUNDED  
THIS APPLIANCE SHALL BE INSTALLED IN ACCORDANCE WITH CURRENT  
REGULATIONS AND USED ONLY IN A WELL-VENTILATED SPACE. REFER TO THE  
INSTRUCTIONS BEFORE INSTALLING AND USING THIS APPLIANCE.  
Technical Data Plate - Data and Location  
(example only)  
Unpacking  
Clearances  
1. Remove all packaging and transit protection including  
all protective plastic coating from the exterior stainless  
steel panels.  
To ensure correct ventilation for the motor and controls,  
the following minimum installation clearances are to be  
adhered to:-  
2. Check the oven and supplied parts for damage. Report  
any damage immediately to the carrier and distributor.  
3. Check that the following parts have been supplied with  
your oven:-  
Top  
Rear  
Left-hand side  
Right-hand side  
100 mm / 4”.  
25 mm / 1”.  
25 mm / 1”.  
25 mm / 1”.  
4 x Leg Adjustable.  
Important:  
4. Report any deficiencies to the distributor who supplied  
your oven.  
5. Securely fit the 4 legs supplied with the oven.  
The vent located at the top (E22 Ovens) or rear (Other 20  
Series Ovens) of the oven must NOT be obstructed.  
Oven Vent Location  
E23, E27, E28 Ovens  
6. Check that the available electrical supply is correct to  
that shown on the Technical Data Plate located on the  
front right hand side panel.  
Oven Vent Location  
E22 Ovens  
Refer to ‘Specifications’ section, ‘Oven  
Specifications Tables’.  
Location  
1. Position the oven in its approximate working position.  
2. The unit should be positioned so that the control panel  
and oven shelves are easily reachable for loading and  
unloading.  
Stand Mounted Oven  
For ovens that are to be mounted to a stand, the oven feet  
are used to level the oven on the stand. Refer to the  
instructions supplied with separately ordered stands for  
mounting details.  
4
Installation  
Electrical Connection  
Warning  
Positioning and Levelling of Oven  
1. Correctly locate the oven into its final operating position  
and using a spirit level, adjust the legs so that the oven  
is level and at the correct height.  
This oven must be earthed / grounded.  
If the supply cord is damaged, it must be replaced by a  
suitably qualified person in order to avoid a hazard.  
2. Adjust the oven feet to level the oven.  
Initial Start-Up  
Each oven should be connected to an adequately protected  
power supply and an isolation switch mounted adjacent to,  
but not behind the oven and must be readily accessible to  
the operator. This switch must be clearly marked and  
readily accessible in case of fire.  
Before using the new oven;  
1. For first time use of the oven, operate the oven for  
about 1 hour at 200°C / 400°F to remove any fumes or  
odours which may be present.  
2. Please refer to the Operation Section of this manual for  
details on how to correctly operate and shutdown the  
oven.  
Check the electricity supply is correct to as shown on the  
Technical Data Plate on the front right hand corner of the  
oven side panel.  
Ovens Supplied with Cordsets (E22M3, E23M3, E27M2, E27M3)  
1. Ensure that the oven is fitted with the appropriate  
power cord and plug.  
NOTE: For non USA / Canada E27M3 Ovens only,  
ovens will be supplied with a bare cord only.  
An appropriate plug must be supplied and  
fitted by a suitably qualified person.  
Ovens Supplied without Cordsets (E28M4).  
NOTE: All electrical connections must only be carried  
out by a suitably qualified person.  
1. Remove oven rear cover panel.  
Electrical  
Panel  
Compression  
Gland  
2. Bring the supply cable up  
through the grommet at the  
back of oven and through the  
compression gland on the  
electrical switchgear panel.  
3. Connect the mains supply to  
the appropriately marked  
terminals on the terminal  
block.  
Grommet  
NOTE:  
Fixed wiring installations must incorporate an  
all-pole disconnection switch.  
5
Operation  
Operation Guide  
Turbofan Ovens have been designed to provide simple operation.  
This oven is intended for use in a commercial kitchen and must only be put to the use for which it was intended, i.e.  
cooking food product. To use this oven correctly please read the following sections carefully:-  
Oven Control Panel  
3
5
4
2
1
Using the Oven  
Description of Controls  
Caution  
Power ‘On’ Indicator Light.  
Indicator light illuminates when the ‘On’ / ‘Off’ -  
‘Temperature’ control is turned ‘On’.  
1
2
Some parts of this oven will become VERY  
HOT during use and could cause burns if  
touched accidentally.  
‘On’ - ‘Off’ and ‘Temperature Control’.  
Used to turn the oven ‘On’ / ‘Off’ and to select the  
oven temperature. Also turns the oven interior light  
‘On’ / ‘Off’. (Not E22M3).  
To Turn ‘On’ the Oven;- Rotate ‘Temperature’ Control  
(2) from the ‘Off’ position. ‘Power On’ Indicator light (1)  
illuminates.  
To Set the Temperature;- Rotate ‘Temperature ’ Control  
(2) to the temperature required. ‘Oven Heating’ indicator  
light (3) will remain ‘On’ until the oven is up to  
temperature.  
Oven Heating Indicator Light.  
3
4
Indicator light illuminates when the elements are  
cycling ‘On’. The oven heating indicator light will  
turn ‘Off’ when the oven is up to temperature.  
Timer Control (60 Minute).  
To Load the Oven;- open the oven door and load  
product. Avoid delays in loading the oven as this will delay  
the oven’s temperature recovery.  
Used to set the bake time. At any stage, the time  
can be adjusted in either direction. For settings less  
than 10 minutes, first set to a higher setting, then  
turn the timer down to the time required.  
To Set the Timer;- Rotate the ‘Timer Control’ (4) to the  
required time.  
Time Up Indicator Light.  
5
Indicator light illuminates and the oven buzzer will  
sound when baking is complete.  
NOTE: This oven can be used without using the  
‘Timer Control’, as it is purely a timer and does  
not control the baking operation of the oven.  
Time Up;- When the timer reaches 0 minutes the buzzer  
sounds and the ‘Time Up’ indicator light (5) illuminates.  
To cancel buzzer, turn Timer Control (4) to the ‘Off’  
position.  
To Turn ‘Off’ the Oven;- Rotate ‘Temperature’ Control  
(2) to ‘Off’ position. ‘Power On’ light (1) will turn ‘Off’.  
6
Cleaning  
c. Pull racks forward to disengage the location pins at  
Cleaning Guidelines  
the rear of rack from the fan baffle, remove the side  
racks from the oven.  
Caution  
Always turn off electrical power at the  
mains supply before commencing cleaning.  
Side Rack  
Rear  
Location  
Pins  
This oven is not water proof. Do not use  
water jet spray to clean interior or exterior  
of the appliance.  
To achieve the best results, cleaning must be regular and  
thorough. If any small faults occur, have them looked at  
promptly. Don't wait until they cause a complete  
breakdown.  
d. Clean all racks with a mild anti bacterial detergent  
and hot water, using a soft bristled brush.  
e. Dry the racks thoroughly with a dry cloth.  
NOTE:  
f. To refit the racks, engage the locating pins at the  
rear of side rack into the locating holes in the fan  
baffle at the rear of the oven.  
Carefully read and follow the safety instructions on  
the label of the cleaning product to be used.  
DO NOT use harsh abrasive scouring pads or  
g. At the same time locate the front of the rack over  
the rack / baffle securing screw and hand tighten  
the rack / baffle securing screw.  
abrasive detergents as they could damage the oven.  
Ensure that any detergent or cleaning material has  
been completely removed after each cleaning.  
h. Refit the wire oven racks to the oven.  
To keep your oven clean and operating at peak efficiency,  
follow the procedures shown below:-  
Fan Baffle (Not E22M3)  
a. Remove side racks as shown previously.  
Oven Cleaning  
b. Undo (anti-clockwise) and remove the rack / baffle  
securing screw at the top of the fan baffle. (E27 /  
E28 Ovens, have 2 rack / baffle securing screws).  
NOTE:  
If the oven usage is very high, the cleaning  
procedure should be carried out on a more frequent  
basis.  
Securing Screw  
Allow the oven interior to cool to approx 50˚C /  
120˚F before commencing cleaning.  
Stainless Steel Surfaces  
a. Thoroughly clean the exterior surfaces of the oven  
with a damp cloth moistened with a mild detergent  
solution or a soft bristled brush.  
Location  
Brackets  
b. Baked on deposits or discolouration may require a  
good quality stainless steel cleaner. Always apply  
cleaner when the oven is cold and rub in the  
direction of the grain.  
c. Tilt the fan baffle forward and lift up off the location  
brackets at rear of oven.  
d. Clean the fan baffle with mild anti bacterial  
detergent and a hot water solution using a soft  
bristled brush.  
Side Racks  
a. Remove the wire oven racks.  
e. Dry fan baffle thoroughly with a soft dry cloth  
before re-fitting.  
b. Partially undo the rack / baffle securing screw (anti-  
clockwise) securing the rack to oven wall, until the  
rack is loose.  
f. Refit the fan baffle and hand tighten the rack /  
baffle securing screw(s) to secure the fan baffle.  
Fan Baffle  
Securing Screw  
7
Cleaning  
Lamp Glass (Not E22M3)  
a. With side racks and fan baffle removed, unscrew  
lamp glass, anti-clockwise.  
Oven Interior  
Allow the oven interior to cool to approx 50˚C /  
120˚F before commencing cleaning.  
a. Remove the oven racks and the fan baffle as shown  
previously.  
b. Clean any build up of grease from the oven interior,  
using a mild anti bacterial detergent, a hot water  
solution and a soft bristled brush.  
c. Dry the oven thoroughly with a soft dry cloth.  
Unscrew Anti-  
Clockwise  
d. Clean the oven regularly with a good quality oven  
cleaner.  
Door Glass Cleaning  
b. Clean the lamp glass using a soft cloth with a mild  
anti bacterial detergent and a hot water solution.  
Ensure that the oven door is cool before cleaning  
the door glass.  
c. Dry the lamp glass thoroughly with a dry cloth.  
d. To refit the lamp glass, screw the glass in clockwise.  
a. Open the oven door.  
Do not over tighten the lamp glass.  
NOTE: Maintain a hold of the door with one hand  
whilst cleaning the inner glass, to prevent the  
door from closing.  
Door Seal  
a. To remove door seal, pull the 1 piece seal forward  
until it pulls out of the location groove around the  
oven. Note the way the seal is fitted to the  
oven, with the lip facing inwards.  
b. Whilst holding the oven door in the open position,  
grasp the bottom of the inner glass and pull glass  
towards you until the top of the inner glass rises up.  
Pull Seal out of  
locating channel  
b. Check for wear and damage to the door seal and  
replace as required.  
c. Wash the door seal in a sink, taking care not to cut  
or damage the seal.  
d. Dry the door seal thoroughly.  
e. Refit door seal with lip facing into centre of the  
oven.  
Refit Seal with Lip  
facing inwards  
c. Grasp the inner glass by the finger tabs at the top  
of the glass and raise the inner glass to the vertical  
position.  
f. Press the door seal into the locating groove in the  
front face of the oven until the seal is properly  
located all around the oven.  
Finger Tabs  
8
Cleaning  
d. Whilst still holding the oven door in the open  
d. Grasp the inner glass firmly on either side and pull  
upwards to remove the inner glass from the locating  
pegs on either side of the door.  
position, clean the inner glass and the inside of the  
outer glass with a conventional glass cleaner.  
e. Dry the oven glass thoroughly with a soft dry cloth.  
f. On completion of door glass cleaning, lower the  
inner glass back into the door, the glass will locate  
itself in the correct position.  
Door Inner Glass Re-Fitting  
a. To refit the inner glass, locate the 2 locating tabs on  
either side of the inner glass into the 2 pegs on the  
door and push down on the inner glass until it locks  
firmly into position.  
g. Close the oven door.  
Door Inner Glass Removal  
It is possible to remove the inner glass completely from  
the oven door for heavy cleaning. This can be done as  
follows:-  
Locating Tab  
a. Open the oven door fully.  
b. Using a suitable instrument, move the door lock  
catches from the unlocked to the locked position to  
prevent the door from closing.  
Locating Peg  
b. Lower the inner glass back into the door, the glass  
will locate itself in the correct position.  
Door Lock Catch in  
Unlocked Position  
c. Open the oven door fully and using a suitable  
instrument, move the door lock catches to the  
unlocked position.  
Door Lock Catch in  
Unlocked Position  
Door Lock Catch in  
Locked Position  
NOTE: Check that both Door Lock Catches are in the  
‘Un-Locked’ position before closing the door.  
d. Close the oven door.  
c. Raise the door until it is restrained by the door lock  
catches.  
9
Fault Finding  
This section provides a reference to the more common  
You may encounter a problem not covered in this section,  
please contact your service provider who will require the  
following information:-  
problems that may occur during the operation of your  
oven. This fault finding guide is intended to help you  
correct and accurately diagnose problems with your oven.  
The Model and Serial Number of the oven, can be  
found on the Technical Data Plate located on the  
front right hand side panel of the oven.  
When fault finding a problem, always use a process of  
elimination starting with the simplest solution and working  
through to the most complex. Never overlook the obvious.  
Fault  
Possible Causes  
Remedy  
Mains isolating switch, circuit breaker or  
Turn 'On'.  
fuses are 'Off' at the power board.  
Door not closed fully.  
Close door. (Refer ‘Door does not close fully’).  
The external power switch is ‘On’, the oven Turn ‘On’ the ‘On-Off Temp Control’ switch.  
is 'Off'. (Not E22).  
(‘Power On’ light will illuminate when oven is  
‘On’) (Not E22).  
Overtemp tripped (No lights, no power  
light).  
Reset Overtemp.  
Oven does not operate / No heat in oven.  
Overtemp faulty.  
Element faulty.  
Call for service.  
Call for service.  
Call for service.  
Call for service.  
Call for service.  
Thermostat faulty.  
Door Switch faulty.  
On / Off Switch faulty.  
Heating Relay faulty (Not E22M3).  
Motor timer faulty (Not E22M3).  
Call for service.  
Call for service.  
Fan motor faulty.  
Call for service.  
Oven heats up but fan does not operate.  
Fan or fan motor obstructed.  
Tray in way of door.  
Call for service.  
Correctly position tray on rack.  
Door Latches in ‘Locked’ position.  
Door glass not fitted correctly.  
Check position of door latches and ‘Unlock’.  
Refit door glass.  
Door does not close fully.  
Refit door.  
Door not fitted correctly.  
Door seal obstruction.  
Correctly install door seal. (Refer to the  
‘Cleaning and Maintenance’ Section).  
Inner glass not fitted.  
Fit inner door glass.  
Oven Door hot to touch  
Bake timer not set correctly.  
For settings less than 10 minutes, first set timer  
to a higher setting then turn back to setting  
required.  
Bake timer does not time down.  
Bake timer faulty.  
Call for service.  
Oven light not illuminating (Not E22M3). Blown bulb.  
Too high a temperature selected.  
Replace bulb.  
Select a lower temperature.  
Oven or racks not level.  
Check oven racks and level.  
Insufficient air space around trays or  
baking tins.  
Ensure oven racks are spaced to allow air flow  
around baking on all shelves.  
Oven overloaded with too much product.  
Opening oven door un-necessarily.  
Re-load oven.  
Uneven cooking.  
Ensure oven door remains closed during the  
baking process.  
Oven door seal damaged or faulty.  
Oven vent restricted.  
Check seals and replace if damaged.  
Ensure oven vent not blocked or shrouded.  
Call for service.  
Faulty thermostat.  
10  
Electrical Schematics  
110-120V, 60Hz.  
220-240V 50/60Hz.  
Electrical Schematic E22M3 Turbofan Oven  
208V, 50-60Hz.  
220V, 50-60Hz.  
230-240V, 50-60Hz.  
Electrical Schematic E23M3 Turbofan Oven  
11  
Electrical Schematics  
208V, 50-60Hz.  
220V, 50-60Hz.  
230-240V, 50-60Hz.  
Electrical Schematic E27M2 Turbofan Oven  
208V, 50-60Hz.  
220V, 50-60Hz.  
230-240V, 50-60Hz.  
Electrical Schematic E27M3 Turbofan Oven  
208V, 50-60Hz.  
220V, 50-60Hz.  
230-240V, 50-60Hz.  
Electrical Schematic E28M4 Turbofan Oven  
12  
Replacement Parts List  
Important:  
Only genuine authorized replacement parts should be used for the servicing and repair of this oven. The instructions  
supplied with the parts should be followed when replacing components.  
For further information and servicing instructions, contact your nearest authorized service provider or Turbofan Dealer.  
When ordering replacement parts, please quote the part number and the description as listed below. If the part required  
is not listed below, request the part by description and quote model number and serial number which is shown on the  
Technical Data Plate.  
Item  
232765  
232766  
234088  
234089  
234107  
234108  
025387  
013431K  
234139  
024503  
024562  
024505  
234802  
234803  
Description  
Oven Element, 1500W, 110 - 120V  
Oven Element, 2000W, 230 - 240V  
Oven Element, 2800W, 230 - 240V  
Oven Element, 2800W, 208 - 220V  
Oven Element, 4500W, 208 - 220V  
Oven Element, 4500W, 230 - 240V  
Fan Motor, 110 - 120V  
E22  
 
E23  
E27M2 / E27M3  
E28  
 
 
 
 
 
  M2 only  
  M2 only  
  M3 only  
  M3 only  
 
 
Fan Motor, 50 / 60Hz, 208 - 240V  
Fan Motor, 50 - 60Hz, 208 - 240V  
Motor Timer, 230V  
 
 
 
 
 
 
 
Relay, 25A  
 
 
Relay, 30A  
 
 
Fuse Holder  
  M3 only  
  M3 only  
Fuse 10A  
 
 
 
 
 
 
 
 
 
025400  
233573  
233607  
Overtemp, 360°C - 680°F  
Overtemp Cap  
 
 
 
 
 
Thermostat, 50 - 260°C / 150 - 500°F  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
233887  
233616  
233617  
233862  
234251  
234136  
011760  
Rotary ON / OFF Switch  
Knob Thermostat, 50 - 260°C  
Knob Thermostat, 150 - 500°F  
Door Microswitch  
Capacitor 5uF  
 
 
LED Indicator, 110 - 250V  
Bake Timer 60 Minute  
 
 
 
233613  
015822  
011794  
Knob Bake Timer (0 - 60 Minute)  
Buzzer, 110 - 120V  
Buzzer, 208 - 240V  
 
 
 
 
 
 
 
 
 
 
 
 
233115  
233884  
231814  
Oven Lamp Lens  
 
 
Lamp Bulb G9 25W, 120V Halogen  
Lamp Bulb G9 25W, 230V Halogen  
 
233370  
233913  
233368  
233346  
234602  
Door Inner Glass - E22  
Door Inner Glass - E23  
Door Inner Glass - E27  
Door Inner Glass - E28  
Door Inner Glass Catch  
 
 
 
 
 
 
 
 
 
233292  
233293  
233294  
Door Hinge - E22  
Door Hinge - E23  
Door Hinge - E27  
 
 
233295  
234465  
232667  
232666  
234466  
Door Hinge - E28  
Door Seal - E22  
 
 
 
 
Door Seal - E23  
 
 
Door Seal - E27M2 / E27M3  
Door Seal E28  
 
 
232379  
Leg Adjustable (73 - 80 mm)  
13  
Replacement Parts List  
Replacement Parts List (Continued).  
Item  
233521  
233522  
232682  
232683  
233558  
233559  
234721  
234722  
233556  
233564  
233565  
233552  
Description  
Side Rack LH, E22  
E22  
 
E23  
E27M2 / M3  
E28  
 
Side Rack RH, E22  
Side Rack LH, E23  
 
 
Side Rack RH, E23  
Side Rack LH, E27M3  
Side Rack RH, E27M3  
Side Rack LH, E27M2  
Side Rack RH, E27M2  
Side Rack, E28  
  M3 only  
  M3 only  
  M2 only  
  M2 only  
 
 
 
 
 
Oven Rack E22, E23  
Oven Rack E27, E28  
Rack / Baffle Securing Screw  
 
 
 
 
14  

Indesit Oven DIMS 53 KC A IX GB User Manual
JVC InteriArt AV 32H47SU User Manual
Lincoln Impinger Conveyor Ovens 1421 000 E User Manual
MaxTech XT 7871 User Manual
Monessen Hearth WC500 User Manual
Philips 15 AA3330 User Manual
Philips 29PT9417 User Manual
Philips 107F5 User Manual
Philips DVP3996 User Manual
Philips MatchLine 21CE7550 User Manual