INSTALLATION / OPERATION
MANUAL
E311 / E311MS
CONVECTION OVEN
F23621-9
Contents
Introduction........................................................................................................2
Installation..........................................................................................................3
Before Connection
Location
Double Units
Electrical Connection
Door Handle
Water connection
Before Use
Specifications.....................................................................................................5
Operation............................................................................................................9
Description of Controls
Baking
Roast ‘n’ Hold
Grilling / Broiling
Cooking Guide .................................................................................................13
Cooking
Bake Off
Roasting
Roast ‘n’ Hold
Cleaning and Maintenance..............................................................................15
Trouble Shooting .............................................................................................16
Oven
Baking
Spare Parts.......................................................................................................18
Circuit Schematic.............................................................................................19
Date Purchased................................................................. Serial No ..........................................................
Dealer............................................................................................................................................................
Service Agent................................................................................................................................................
1
Introduction
We are confident that you will be delighted with your TURBOFAN OVEN, and it will become a most valued
appliance in your commercial kitchen.
A new oven can seem very complex and confusing at first glance. To ensure you receive the utmost
benefit from your new Turbofan, there are two important things you can do.
Firstly
Please read the instruction book carefully and follow the directions given. The time taken will be well
spent.
Secondly
If you are unsure of any aspect of the installation, instructions or performance of your oven, contact your
E311 dealer promptly. In many cases a phone call could answer your question.
Model Options
This manual covers models E311 and E311MS.
The E311 models feature a vitreous enamel front exterior finish and full glass door.
The E311MS models feature a stainless steel front exterior finish and a stainless steel exterior door with
full viewing window.
The functionality of both model series are identical.
Note: Both model series are marked with the control panel coding “31”, however the full and specific
model option is found on the appliance rating plate.
2
Installation
Installation Requirements
It is most important that this oven is installed correctly and that operation is correct
before use.
Installation shall comply with local electrical, health and safety requirements.
Before Connection to Power Supply
•
•
Remove all packing.
Check equipment and parts for damage. Report any damage immediately to the carrier and
distributor.
•
•
Remove protective plastic coating from the side panels.
Check that the following parts have been supplied with your oven:
4 x 4” Legs (Canada only)
4 x Oven racks
•
•
•
•
Report any deficiencies to the distributor who supplied the oven.
Fit the feet to the oven.
Fit door handle to oven door.
Check that the available power supply is correct to that shown on the rating plate located on the
right -hand side panel.
208V AC 60Hz, 14.0A, 2.9kW @ 208V
220-240V AC 60Hz, 13.0A, 3.1kW @ 240V
208-220V AC 50Hz, 14.6A, 3.2kW @ 220V
230-240V AC 50Hz, 13.0A, 3.1kW @ 240V
Location
•
To ensure correct ventilation for the motor and controls the following minimum installation
clearances are to be adhered to:
Top
Rear
Left-hand side
Right-hand side
8” / 200mm
1” / 25mm
1” / 25mm
1” / 25mm
•
•
Position the oven in its working position.
Use a spirit level to ensure oven is level from side to side and front to back. (If this is not carried
out, uneven cooking could occur). The feet/legs used with bench/floor mounting or provided with
stands are adjustable and will require adjusting in levelling the unit.
•
The unit should be positioned such that the operating panel and oven shelves are easily reachable
for loading and unloading.
Important:
THE VENT LOCATED ON THE OVEN TOP MUST NEVER BE OBSTRUCTED.
Double Units
•
When it is desired to mount one unit on top of another the 31mm (1¼") high spacer feet must be
used. These short feet should be screwed on, and the unit lifted on top of the bottom unit, where it
locates safely under its own weight, for normal applications.
3
Installation
Electrical Connection
•
•
Ensure unit is fitted with appropriate cord and plug.
To access the electrical connection terminal block, grounding lug (marked with green), and strain
relief, remove the back panel (4 screws).
WARNING - THIS APPLIANCE MUST BE GROUNDED
Water Connection (Canada only)
•
A cold water supply should be fitted to the water inlet which is located on the rear of the left hand
side of the unit.
•
A connection elbow and sealing washer is supplied with this unit for direct connection of a 1/2” ID
hose, and is recommended for easy installation and service.
•
•
Connect water supply - Max inlet pressure 80psi / 550kPa.
Turn on water supply to check for leaks.
Important
:
MAXIMUM INLET WATER PRESSURE IS 80 psi / 550 kPa.
Before Use
•
Operate the oven for about 1 hour at 200°C (400°F) to remove any fumes or odours which may be
present.
4
Specifications
E311
796
600
(31 3/8”)
(23 5/8”)
WATER ENTRY
ELECTRICAL ENTRY
41
120
16
(1 5/8”)
(5/8”)
(4 3/4”)
45
(1 3/8”)
Front
Side
Plan
Electrical Connection
208V AC 60Hz, 14.0A, 2.9kW @ 208V
220-240V AC 60Hz, 13.0A, 3.1kW @ 240V
208-220V AC 50Hz, 14.6A, 3.2kW @ 220V
230-240V AC 50Hz, 13.0A, 3.1kW @ 240V
Cold Water Connection
(Canada only)
1/2” I.D Hose (80psi maximum pressure)
5
Specifications
E311MS
796
600
(31 3/8”)
(23 5/8”)
WATER ENTRY
ELECTRICAL ENTRY
41
120
16
(5/8”)
(1 5/8”)
(4 3/4”)
45
(1 3/8”)
Front
Side
Plan
Electrical Connection
208V AC 60Hz, 14.0A, 2.9kW @ 208V
220-240V AC 60Hz, 13.0A, 3.1kW @ 240V
208-220V AC 50Hz, 14.6A, 3.2kW @ 220V
230-240V AC 50Hz, 13.0A, 3.1kW @ 240V
Cold Water Connection
(Canada only)
1/2” I.D Hose (80psi maximum pressure)
6
Operation
Operation Guide
Description of Controls
Power
31
Depress to switch power on or off (switch
illuminates when power is on).
Thermostat
Temperature range 50 - 250°C (120 - 550°F).
Indicator illuminates when the elements are cycling
ON to maintain set temperature.
Grill/Broil position - The grill/broil indicator will
illuminate indicating that the grill/broil function has
been set. The heating indicator will also illuminate
whenever the elements are on.
Bake Timer
1 Hour bake timer.
(Indicator illuminates when “time up” (0) reached,
and buzzer sounds).
N
Roast ‘n’ Hold
Depress switch to activate ’Roast ’n’ Hold’ function.
(Switch illuminates when ON).
10
20
150
120
30
Roast Timer
40
50
3 Hour roast timer.
(Indicator illuminates when “time up” (0) reached).
Product is held at 75°C (167°F).
60
90
Steam Switch (Canada only)
Push switch to activate water injection. (Water
injects into oven while button is depressed).
Light Switch
Push switch to activate light.
(Light illuminates while button is latched in the
down position).
7
Operation
Baking
1. Turn power on
Power switch illuminates when it is depressed and latched in the down position.
2. Set thermostat to desired temperature
The heating indicator light will illuminate whenever the elements are cycling on to maintain
the set temperature.
3. Load oven
Once the oven is up to temperature, open the door and load the oven with product. Avoid
delays in loading the oven with the door open as this will delay the oven’s temperature
recovery.
Note:
The oven’s fan will switch off and the oven lights will illuminate when the door is opened.
4. Set bake timer to desired time
To set timer, turn knob clockwise to the required time. At any stage, the time can be adjusted
in either direction.
For settings less than 10 minutes, first set to greater setting, then turn down to the required
time period.
Note:
This 60 minute timer is completely independent of the oven control.
5. Water injection (Canada only)
To steam the oven while baking, push the steam switch on the control panel. We
recommend a 2-15 second injection period, according to product need, for this oven.
Keep switch depressed for required steam period.
6. Light
To view the product while baking, depress the light switch on the control panel. The light will
stay on while the switch is latched in the down position.
7. Time up.
When the timer reaches 0 minutes the buzzer sounds and indicator illuminates.
To cancel the buzzer turn the timer to the off position.
8. Unload oven
Open the door and unload the oven .
Note:
The oven’s fan will switch off and the oven light will illuminate when the door is opened.
8
Operation
Roast ‘n’ Hold
1. Turn power on
Power switch illuminates when it is depressed and latched in the down position.
2. Set thermostat to desired temperature
The heating indicator light will illuminate whenever the elements are cycling on to maintain
the set temperature.
3. Load oven
Once the oven is up the temperature, open the door and load the oven with product. Avoid
delays in loading the oven with the door open as this will delay oven temperature recovery.
Note:
The oven elements and fan will switch off and the oven lights will illuminate when the door is
opened.
4. Set roast timer to desired time
This 3 hour timer is electrically driven and is set by turning the timer knob in either direction to
the required time. The timer can be set when convenient, but will not start working until the
oven control is set and the Roast ’n Hold switch is depressed (switch illuminated).
5. Depress roast switch
Depress the Roast ’n Hold switch. The switch will illuminate and the timer will begin to count
down.
6. Water injection (Canada only)
To steam the oven while roasting, push the steam switch on the control panel. We
recommend a 2-15 second injection period, according to product need, for this oven.
Keep switch depressed for required steam period.
7. Light
To view the product while roasting, depress the light switch on the control panel. The light
will stay on while the switch is latched in the down position.
8. Hold
When the timer reaches the hold position, the main oven thermostat is turned off and a
pre-set hold thermostat located behind the control panel will control the oven to keep the food
warm at serving temperature as long as required until the Roast ‘n Hold switch is turned off.
Note:
The hold light will illuminate when the timer reaches hold until the Roast ’n Hold switch is
turned off. The hold light may come on briefly when the Roast ’n Hold control is first switched
on until the oven heats up beyond the pre-set holding temperature.
9
Operation
Grilling / Broiling
1. Grilling / Broiling
Turn thermostat fully clockwise until the GRILL/BROIL position is reached. The GRILL/
BROIL indicator will illuminate indicating that the GRILL/BROIL function has been set. The
heating indicator will also illuminate whenever the element is on.
It is recommended that the GRILL/BROIL mode is only used with the oven door open as the
oven fan is then automatically off. If however the GRILL/BROIL mode is used with the door
closed, the elements will cycle on/off when oven temperature rises above 300°C (570°F) to
prevent damage to the oven.
2. Load oven
Place an oven rack normally on the top position. When the element has reached bright red
(5 minutes), position the dish under the GRILL/BROIL element. Heat food on one side, then
turn on the other side.
It is not recommended to close the door when grilling/broiling.
3. Set bake timer to desired time
To set timer, turn knob clockwise to the required time. At any stage, the time can be adjusted
in either direction.
For settings less than 10 minutes, first set to greater setting, then turn down to the required
time period.
Note:
This 60 minute timer is completely independent of the oven control.
4. Time up.
When the timer reaches 0 minutes the buzzer sounds and indicator illuminates.
To cancel the buzzer turn the timer to the off position.
5. Unload oven
Open the door and unload the oven .
10
Cooking guide
This TURBOFAN oven will cook a greater quantity of food faster, at a lower temperature and more evenly
than an ordinary oven. As many excellent recipe books are published, it is not our intention to list recipes,
but to provide a temperature and time chart as a guide.
When the door is opened the fan will switch off but elements will remain on to provide quick heat recovery.
A high powered top element is fitted for toasting or broiling.
Baking
Select a temperature up to 20°C (35°F) lower than used in a conventional oven and preheat until
HEATING indicator goes out. When the HEATING indicator goes out, the oven has reached the
desired temperature and food may be placed in the oven allowing air space between cooking
utensils and around the oven walls.
The following are only approximate guides - use your judgement.
FOOD
TEMP °C
165
165
160
150
160
140
130
200
165
175
165
130
140
130
165
130
TEMP °F
330
330
320
300
320
285
265
390
330
350
330
265
285
265
330
265
TIME
Sponges
Small Cakes
Butter Cakes
Fruit Loaf
Macaroons
Biscuits
10-12 mins
8-12 mins
35 mins
40-50 mins
15-20 mins
12-20 mins
15-20 mins
10-12 mins
35-50 mins
25-35 mins
1-1½ hrs
2-3 hrs
Shortbread
Scones
Madeira
Bread
Plain Fruit Cake
Rich Fruit Cake
Gingerbread
Baked Custard
Souffle
35-50 mins
50 mins
25 mins
Rice Pudding
Pastry
2-3 hrs
Puff
220
175
205
185
185
430
350
400
365
365
8-12 mins
8-12 mins
8-12 mins
12-20 mins
35 mins
Short
Flakey
Jam
Fruit
11
Cooking guide
Roasting
Set the oven temperature to 150-170°C (300°F-340°F). The hot air circulating in the oven reduces
moisture loss and shrinkage. Roasting times are reduced by approximately 10 minutes per kg.
MEAT
TIME per kg
Beef - Rare
Beef - Medium
Beef - Well Done
Veal
30-40 min
40-50 min
50-60 min
50-70 min
30-40 min
50 min
Lamb
Duck
Goose
50 min
Turkey
30-40 min
Chicken
- under 1kg
- over 1kg
50-60 min
40 min
Roast-’n’-Hold
This system will automatically cook food for a set time, then hold the oven at a preset temperature
indefinitely to maintain food at a serving temperature after cooking has been completed.
When the oven has reached the set temperature, place food in the oven, set roast cooking time and
depress the Roast ’n’ Hold button. The hold indicator will come on when cooking is complete.
To return to normal operation, push the Roast ‘n’ Hold switch again (switch will cease illuminating).
Browning
Different foods may be cooked together, eg baking and roasting may be carried out at the same time.
Food which requires a slightly higher temperature or more browning should be placed at the top of the
oven, so that the broil element may be selected (with the door shut) during the last few minutes of `
cooking. As the top element is quite powerful, keep a close watch on browning progress.
Grilling/Broiling
Turn the oven thermostat right around to GRILL/BROIL. Place an oven rack normally on the second
position from the top. Place the food on a grill tray. This allows fat to drain, to prevent smoking. When
the element has reached a bright red (5 minutes) position the dish under the GRILL/BROIL element.
Heat food on one side, then turn on the other side.
Toast, sandwiches etc., on a scone tray on the top rack position.
FOOD
MINUTES per SIDE
Steak - 25mm thick
- Rare
6-8
- Medium
9-11
Chops
- 25mm thick
12-15
3-4
Bacon
Ham 15mm thick
Tomatoes - halved
Mushrooms
8-10
10-12
10-12
10-15
Onions - raw sliced
It is not recommended to close the door when grilling/broiling.
12
Cleaning
Cleaning Guidelines
Caution:
ALWAYS TURN OFF THE POWER SUPPLY BEFORE CLEANING.
THIS UNIT IS NOT WATER PROOF.
DO NOT USE WATER JET SPRAY TO CLEAN INTERIOR OR EXTERIOR OF THIS UNIT.
Exterior
Clean with a good quality stainless steel cleaning compound. Harsh abrasive cleaners may damage
the surface.
Interior
Ensure that the oven chamber is cool. Do not use wire brushes, steel wool or other abrasive materials.
Clean the oven regularly with a good quality oven cleaner. Take care not to damage the fan or the
tube at the right side of the oven which controls the thermostat.
Oven Racks
To remove, slide out to the stop position, raise the front edge up, and lift out.
Side Racks
Undo the thumbscrew (anti-clockwise rotation) securing rack to oven wall, swing rack towards centre
of oven to disengage location pin at front of side, and pull rack forward to remove. To replace, engage
rack in rear holes, swing towards side of oven to engage in front hole, and replace thumbscrew.
Bottom Element Cover
Lift out vitreous enamelled element cover and thoroughly clean on a routine basis (minimum once per
week.
Fan Baffle
To remove, unscrew the oven lamp glass and lift the baffle out. To replace, locate the bottom edge of
the baffle over the bottom element terminal plate and secure in place with the oven lamp glass.
Do not over tighten lamp glass.
Oven Seals
To remove, hold at their centre point and pull forward until they unclip. Remove side seals first, then
top and bottom. The seals may be washed in the sink, but take care not to cut or damage them.
To replace, have the lip facing the oven opening. Fit the top and bottom seals first, then the side
seals.
Oven Door Glass
Clean with conventional glass cleaners
13
Trouble-shooting
Oven trouble-shooting
Fault
Possible Cause
Remedy
The oven does not operate / start. The mains isolating switch on the Turn on.
wall, circuit breaker or fuses are
“off” at the power board.
The power switch on the oven is
off.
Depress switch. Switch will
illuminate.
Bake timer does not time down.
Roast timer does not time down
Oven light not illuminating.
Bake timer not set correctly.
For settings less than 10 minutes,
first set to greater setting then
turn back to desired setting.
Roast ‘n’ Hold button not
depressed.
Depress Roast ‘n’ Hold button.
(Roast timer only operates when
Roast function is selected).
Blown bulb.
Replace bulb.
No water injection / steam.
(Canada only)
Water not turned on.
Turn water on at water supply.
14
Trouble-shooting
Baking trouble-shooting
Moist sticky crust
Too much sugar.
Hump or cracks on top
Too much flour.
Oven too hot.
Heavy compact textures
Too much shortening.
Too much sugar.
Oven not hot enough.
Over beating.
Undersized cake
Too large a pan.
Oven too hot.
Not enough baking powder.
Uncooked streak at bottom
Cake falling
Under mixing of ingredients.
Oven not hot enough.
Too much liquid.
Too much baking powder.
Too much shortening.
Too much sugar.
Oven not hot enough.
Insufficient baking.
Moving cake during baking.
Mixture running over pan
Dry cake
Pan too small.
Oven not hot enough.
Too much sugar or shortening.
Too much baking powder.
Too much flour.
Not enough sugar or shortening.
Too much baking powder.
Over beaten egg white.
Over baking at too low a temperature.
Coarse Texture
Uneven cooking
Too much baking powder.
Not enough liquid.
Oven not hot enough.
Insufficient creaming of shortening and sugar.
Too high a temperature selected.
Oven or racks not level.
Insufficient air space around trays or baking tins.
Opening oven door unnecessarily.
Faulty thermostat, oven door seal or restricted
oven venting.
Smoking or discoloration around door
Oven steaming
Oven too hot.
Food spillovers not cleaned up.
Faulty oven door seal.
Overcrowding oven and not increasing initial tem-
perature for this extra food.
Frozen or chilled food will increase moisture in
the oven.
Adding water with meat while roasting.
Opening oven door frequently.
Obstructing oven vent or air circulation.
15
Spare parts
Replacement Part List
Controls
021473
017121
020823
020849
011760
011794
021476
011419
021472
021474
024773
024562
018223
002990
003002
003434
013521
014218
Switch - power
Thermostat
Knob - thermostat / bake timer
Neon indicator
Bake timer
Buzzer
Switch - ‘roast n hold’
‘Roast n hold’ timer
‘Roast n hold’ timer knob
Steam switch
Light switch
Relay - hold
Hold thermostat
Microswitch
Oven lamp glass
Silk gasket
Oven lamp - 40W miniature Edison screw (E311)
Oven lamp - 25W miniature Edison screw (E311MS)
Motor & Elements
003113
003114
011604
003074
013431
013432
024562
Oven top element 208 volts
Oven bottom element 208 volts
Oven top element 240 volts
Oven bottom element 240 volts
Fan motor
Oven fan
Relay - power
Steam System (Canada only)
020851
021526
021527
Water solenoid
Water inlet elbow
Washer
Door
014225
023257
021469
021468
021465
025499
023264
023263
023263
011005
025501
025502
Oven door seal strip (Side)
Oven door seal strip (Top / Bottom)
Handle assembly (E311)
Handle (E311)
Handle bracket (E311)
Handle (E311MS)
Door outer glass (E311)
Door outer glass (E311MS)
Door inner glass
Door catch
Door catch plate (E311MS)
Door bush
Racks
023255
Oven side rack LH
Oven side rack RH
Oven rack
Element front support
Bottom element cover
Fan baffle
023256
023254
004874
004993
004595
16
Circuit schematic
17
|