Mitsubishi Electronics DX TL4509EZ User Manual

DIGITAL RECORDER

USERʼS MANUAL

MODEL

DX-TL4509E

DX-TL4509E(Z)

THIS INSTRUCTION MANUAL IS IMPORTANT TO YOU. PLEASE READ IT BEFORE USING YOUR DIGITAL RECORDER.

Note: This symbol mark is for EU countries only.

This symbol mark is according to the directive 2002/96/EC Article 10 Information for users and Annex IV.

Your MITSUBISHI ELECTRIC product is designed and manufactured with high quality materials and components which

can be recycled and reused.

This symbol means that electrical and electronic equipment, at their end-of-life, should be disposed of separately from

your household waste.

Please, dispose of this equipment at your local community waste collection/recycling centre.

In the European Union there are separate collection systems for used electrical and electronic product.

Please, help us to conserve the environment we live in!

Notice about construction of the surveillance system using this unit

•

This unit can be controlled by the external devices via RS-232C terminal or LAN terminal. This unit can also be used to

control external devices via external terminal, RS-422/485 terminal, or RS-232C terminal. Owning to these functions,

this unit ﬂexibly applies to the high grade security system, but the whole surveillance system may be affected by the

malfunction of this unit or the external devices depending on the setting contents of this unit, the connection with the

external devices, or combination between this unit and the external devices.

•

When configuring a surveillance system using this unit, it is recommended to confirm first that this unit operates

normally with the other devices connected.

•

It is recommended to copy or back up the important recorded contents.

Damages rising out of any operational error of the surveillance system or loss of the recorded data or any other

damages because of any user malfunction of this unit are not covered.

•

Do not use the notiﬁcation function of this unit for making critical judgement nor any purpose related to human lives.

When this unit cannot recognize the external device which is being used for recording due to the power failure,

decreased voltage, or other failures, the recording point may be moved to the internal HDD of this unit or the other

external HDD. To prevent occurrence of such problem, it is recommended to use uninterruptible power supply.

If the power plug is disconnected or the breaker switch is turned off during recording, HDD may be damaged or

playback of recorded data may become impossible.

•

If the breaker switch is turned on and off everyday, set the timer recording to be performed only for the period that the

breaker is on and do not turn off the breaker during recording.

There may be cases when the unit's built-in motion detection function does not operate properly due to external

condition, video input signal, or other factors.

The user will not be indemniﬁed for problems (e.g., recording failure or playback failure) that occur with either the unit or

a connected device during operation. It is recommended to back up the important recordings regularly as a precaution

against possible breakdowns and accidents.

Recordable time and product warranty

Continuous recordable time and the estimated time displayed on the menu screen indicate the continuous time of

recording operation of this unit. They indicate the period neither for product warranty nor that for reliability of used parts.

•

This unit uses a built-in HDD, which is a precision device. Handle this unit with sufﬁcient care.

Do not subject this unit to vibrations or shocks. This may cause trouble specially when the power of the unit is turned

on or when the HDD is being accessed, and sufﬁcient care is required.

•

Do not disconnect the power plug while the power of the unit is turned on or while recording or playing.

For early detection of faults, we recommend that you request inspection once a year.

The HDD and cooling fan of this unit are driving parts. For stable recording, it is recommended that both of these parts are

replaced every 30,000 hours.

(This interval is for reference purpose only and does not indicate the warranty period of the parts.)

Beginning

Caution and care (continued)

DISCLAIMER

In any event, Mitsubishi assumes no responsibility or reliability for the following:

1. Disassembly, repair, or alteration of this unit by user or installer.

2. Failure or breakdown in or damage to this unit resulting from misuse or careless handling by user or installer.

3. Inconvenience or damages arising out of inability to display or record pictures due to any reason or cause other than

breakdown or failure in this unit.

4. Failure in this unit due to combination with other equipment manufactured by a third party or inconvenience or

damages resulting from such failure.

5. Inconvenience, damages, or claims arising out of breakdown in this unit or loss of recorded video data due to

replacement of the built-in HDD by user or installer.

6. Inconvenience or damages arising out of breakdown in this unit or inability to display or record pictures due to natural

disaster including earthquake and storm.

7. Inconvenience, damages, or claims arising out of breakdown in this unit or loss of recorded video data due to impact

or vibration to the built-in HDD or an environmental factor such as temperature at the installation site.

8. Demand for damages or other claim of infringement of privacy if the pictures monitored or recorded by user become

public or are used for any purpose other than surveillance for whatever reason.

INSTALLATION LOCATION AND HANDLING

•

Place this unit horizontally and in a stable place. If this unit is not placed correctly and used in an unstable place, the unit

may be damaged such as removal of the DVD/CD disc.

•

Do not place this unit close to other electronic or magnetic equipment. This will avoid video and audio distortion.

When a monitor and this unit are placed vertically, the pictures may be distorted or DVD/CD disc may not be ejected.

Do not let stick your hands into the disc loading slot. You may get your hand caught in the slot and may got injured. If you

get your hand caught, do not get out of the slot by force. Contact your dealer after turning off the power and disconnecting

the plug.

DVD/CD DISC

•

Do not use the disc cracked, deformed or repaired with adhesive. The disc may ﬂy into pieces and cause injury.

Do not touch the playback surface when holding the disc.

When dew condensation occurs on the disc, wipe the surface off before use.

Dirt such as ﬁngerprints or dust causes the deterioration of the picture quality and audio quality. Gently wipe the DVD/CD

disc from the center to the outside with a soft cloth.

•

When the disc is very dirty, soak a soft cloth with water and screw water of it, wipe off the dirt lightly, then wipe with a dry

cloth.

•

Do not use solvent such as benzine and thinner, a record cleaner, and static-stopper. They may damage the disc.

Do not use the disc described below. They may damage the disc itself or this unit.

Discs on which a piece of paper or sticker is put, or a disc damaged.

Discs which the label is peeled or a disc with oozing.

Discs cracked, deformed, or repaired with adhesive.

•

Store the disc in the speciﬁed casing, avoiding the following places.

Places where it will be subjected to direct sunlight.

Places with excessive dust.

Places where it will be subjected to high temperatures or high humidity.

DVD movie (cinema) or personal recorded picture cannot be played back on this unit. Only the pictures recorded on this

unit can be played back.

Do not use the disc which has been used on the personal computer, failed to be copied, or stopped during copying due to

the power failure because they may cause malfunction of the unit.

Although you can copy the data on DVD/CD with this unit and playback that data on the personal computer using the

supplied application software, not all the personal computers or DVD/CD drives are ensured for proper playback of such

data.

•

MAINTENANCE OF THE LENS FOR RECORDING/PLAYBACK (LASER PICKUP)

•

When any dust adheres on the lens for recording/playback, the picture may be distorted or the audio may skip. Also normal

recording or playback may not work. Ask your dealer how to correct this problem.

Be careful, do not use the commercial lens cleaning disc, they may damage the lens.

PRECAUTION CONCERNING EXTERNAL DEVICE

•

The various external HDDs can be connected to this unit in order to expand the memory or to use as the copy device.

However, during recording or playing back a picture at high rate, some pictures may be missed due to the slow rate of data

transfer or the slow speed of response from the external device connected. Be sure to check the operation sufﬁciently in

advance.

•

Do not use the power control function of the external device which uses bus power of this unit.

The external device to be used may be unsuitable for the operation you want to set. It is recommended to consult your

dealer when using the external device.

Warning

This is a class A product. In a domestic environment this product may cause radio interference in which case the user may

be required to take adequate measures.

CLASS 1 LASER PRODUCT

Contents

Caution and care............................................................ 2

Contents.......................................................................... 5

Note ................................................................................. 6

Software License Agreement........................................ 7

Communications by Web Browser ............................. 24

Communications by Web Browser................................ 24

The personal computer product requirements........ 24

Connections............................................................ 24

Main Menu.................................................................... 25

Live Monitoring........................................................ 26

Playback ................................................................. 27

Conﬁguration Menu................................................. 28

User Registration................................................29

Recorder Title & Camera Titles ..........................30

E-mail Setup.......................................................30

Access Mode Setup ...........................................32

Clock Setup........................................................32

Logout..................................................................... 33

Change Login User................................................. 33

How to set the menus.................................................... 8

Setting the menus .......................................................... 8

Setting the menu using a mouse.............................. 8

Setting the menu using the front panel buttons........ 8

Displaying a menu screen ........................................ 9

Closing a menu screen............................................. 9

Selecting an item...................................................... 9

Inputting numbers................................................... 10

Setting parameters ................................................. 10

Symbols in the menus.................................................. 11

Setting the time and date ............................................ 12

Troubleshooting ........................................................... 34

Time/Date Setting......................................................... 12

Warnings and CALL OUT output................................. 36

Using the basic multiplexer functions ....................... 13

Basic multiplexer functions........................................... 13

Multiplexer buttons ................................................. 13

Warnings and their appropriate countermeasures........ 36

Controlling the camera................................................ 14

PTZ control using the menu ......................................... 14

PTZ control using the front panel buttons .................... 14

Recording the picture manually ................................. 15

Basic manual recording................................................ 15

Setting the recording rate and picture grade for

normal recording..................................................... 15

Playing back the recorded data.................................. 16

Basic playback ............................................................. 16

Searching the desired picture..................................... 17

Basic search................................................................. 17

Search by Time and Date....................................... 17

Search by Alarm List............................................... 18

Copying the recorded data.......................................... 19

Copy Data to Copy 1 Drive/Set Copy 1 Drive .............. 19

Copy Data to Copy 2 Drive/Set Copy 2 Drive .............. 20

Copying the data of this unit to a video cassette.......... 21

Playback software ........................................................ 22

System requirements.............................................. 22

Starting up the application software ....................... 22

Operational panel ................................................... 22

File menu................................................................ 23

Search menu .......................................................... 23

Operation menu...................................................... 23

Bookmark menu ..................................................... 23

View menu.............................................................. 23

Grouping menu....................................................... 23

Menus apperaing with right button clicking............. 23

How to read this manual

Viewing displays

(Refer to this information when operating):

Reference information concerning operation

(Caution required):

Cautionary items concerning operation

Finding desired information

There is a “Contents” at the beginning of this manual.

Troubleshooting

Read Troubleshooting (pages 34, 35) for possible

remedies to the problem.

Microsoft is either registered trademarks or trademarks

of Microsoft Corporation in the United States and/or other

countries.

All other company and product names appearing herein

are the property of their respective owners.

Beginning

Note

Thank you for purchasing Mitsubishi digital recorder DX-TL4509E/DX-TL4509E(Z) (hereinafter referred to as “Product”).

Before using this Product, please be sure to read the following Software License Agreement with regard to the software

contained in this Product (hereinafter referred to as “Licensed Software”). By using this Product, you are agreeing to be

bound by the terms and conditions of the following Software License Agreement.

This Product contains software programs that are covered by GNU General Public License or GNU Lesser General Public

License. Such software programs are excluded from Licensed Software and not covered by the following Software License

Agreement. For the terms and conditions for use of the software programs covered by GNU General Public License or GNU

Lesser General Public License, please see “Notice about software to which GNU GPL/LGPL is applied”*.

In addition, this Product contains “Apache” and “OpenSSL (including “Original SSLeay” library).” These software programs

are also excluded from Licensed Software and not covered by the following Software License Agreement. For the terms and

conditions for use of these software programs, please see “Notice about Apache software”* and “Notice about OpenSSL

software”*.

Each of “Berkeley Database,” “agetty,” “expat,” and “zlib” contained in this Product is other open source software. These

software programs are excluded from Licensed Software and not covered by the following Software License Agreement. For

the terms and conditions for use of these software programs, please see “Notice about other open source software”*.

The documents of “Notice about software to which GNU GPL/LGPL is applied,” “Notice about Apache software,” “Notice

about OpenSSL software,” and “Notice about other open source software” are contained (in the format of electronic

files as notice_GPL_LGPL_ja.pdf, notice_Apache_ja.pdf, notice_OpenSSL_ja.pdf, and notice_other_ja.pdf) in the

“OpenSoft_License” folder in the CD supplied with this Product.

Software License Agreement

This Software License Agreement (“Agreement”) is an agreement between you (“User”) and Mitsubishi Electric Corporation

(“Licensor”) with regard to the license to use Licensed Software.

Article 1 (Grant of license)

Licensor hereby grants to User a nonexclusive, nontransferable license to use Licensed Software.

Article 2 (License)

1. The license to use Licensed Software granted hereunder shall mean the User’s right to use Licensed Software solely

on this Product. User is hereby allowed to refer to the descriptions and instructions related to Licensed Software

contained in the user’s guide of this Product to the extent necessary for use of such Licensed Software.

2. User shall not reproduce, copy, or modify, in whole or in part, or make addition or alteration to Licensed Software and

pertinent documents.

3. User shall use Licensed Software in accordance with the operating instructions described in the user’s guide.

Article 3 (License conditions)

1. User shall not transfer to any third party the license stipulated in the preceding article.

2. User shall not disassemble, decompile, or otherwise analyze the source code of Licensed Software.

Article 4 (Ownership of Licensed Software)

All and any rights including copyrights related to Licensed Software and pertinent documents shall be owned by

Licensor or the original right holder who granted to Licensor the right to sublicense Licensed Software (hereinafter

referred to as “Original Right Holder”). User shall not own any rights other than the license granted hereunder with

regard to Licensed Software and pertinent documents.

Article 5 (Disclaimer)

Licensor and Original Right Holder shall make no warranties whatsoever with regard to Licensed Software and have

no liability for any damages suffered by User or any third party arising out of User’s execution of the license granted

hereunder, except in cases where any applicable laws are extended.

Article 6 (Responsibility toward third party)

Any issues related to intellectual property rights, including but not limited to rights of privacy, copyright, and

patent, involving any third party arising out of User’s use of Licensed Software shall be settled by User on its own

responsibility, and Licensor shall have no responsibilities for such issues.

Article 7 (Conﬁdentiality)

User shall keep secret the details of Licensed Software and pertinent documents provided hereunder and the

contents of this Agreement that are unknown publicly and shall not disclose or leak such details and contents to any

third party without consent of Licensor.

Article 8 (Termination)

In case of either of the following events, Licensor may terminate this Agreement immediately and may claim against

User for resulting damages it suffers.

(1) User’s violation of any provision of this Agreement.

(2) Occurrence of filing against User for seizure, provisional seizure, provisional injunction, or other forcible

execution.

Article 9 (Disposal of Licensed Software)

If this Agreement is terminated pursuant to the preceding article, User shall dispose of Licensed Software, pertinent

documents, and any copies thereof in its possession within two weeks after termination hereof and shall provide

Licensor with a written certiﬁcation of such disposal.

Article 10 (Update of Licensed Software)

If User updates Licensed Software using an update CD supplied or sold by Licensor or any other means, this

Agreement shall remain applicable to the updated version of such Licensed Software, unless Licensor provides

additional separate terms and conditions for using the updated version of such Licensed Software.

Article 11 (Miscellaneous)

1. If any provision of this Agreement is determined to be invalid by law, the remaining provisions hereof shall remain

valid and enforceable.

2. If any doubt arises in relation to matters not deﬁned herein or interpretation hereof, Licensor and User shall discuss

such doubt and attain a solution in a faithful manner.

Beginning

How to set the menus

Setting the menus

The operations of this unit can be set via a menu displayed on OUTPUT A monitor. You can select and set the menu by using

the buttons on the front panel or using a USB mouse connected to the unit. When using the front panel buttons, the numbers

1-16 (number buttons) and letters A to E (A to E buttons) represent the GUI button of the menu screen.

The menu can only be displayed through OUTPUT A monitor. The menu cannot be displayed through OUTPUT B monitor.

Setting the menu using a mouse

Mouse is not supplied with this unit.

Wheel

Use the standard USB mouse which has left and right

buttons as illustrated to the left. Note that you cannot

use the mouse with this unit depending on the mouse

connected.

Left button

Right button

step

1. Use the left and right mouse buttons to set the

menu.

•

Click the left button to open the menu or select

a needed item, etc.

Click the right button to set the active area for

motion detection function.

The wheel on a mouse does not work with this

unit.

Mouse

Setting the menu using the front panel buttons

step

1. Use the SET UP button, number buttons, and A to E

buttons to set the menu.

•

Press the SET UP button to display the menu

screen.

Press the number buttons (1 to 16) and A to

E buttons to open each menu or to select the

needed item.

Displaying a menu screen

step

1. Press the SET UP button or click the left button on

the mouse to display a menu.

•

The <User Menu> appears.

To open other menu, press the D button or left-

click on “Next .”

When you use a mouse, click the following area to

operate.

Exit

Click this area

User Menu

100 000 000

Copy

Information

PTZ Control

Protect Data

Exit

Closing a menu screen

step

1. Press the E button or left-click on the “Exit” to close

the menu.

You cannot close the menu by pressing the SET UP

button on the unit.

Setup Menu

200 000 000

Recording

System

Timer

Motion Det

Menu Data

Exit

Selecting an item

step

1. Press the front panel button of the needed item

number or left click on the needed item.

•

The selected item menu opens.

Select an item and press the number, or click

on the menu to open the item.

Exit

Reset to Factory Setting

On Screen Display Setting

Multiplexer Setting

Password Setting

Rear Terminal Setting

Setup Menu

200 000

Menu Language Selection

Recording

Timer

Motion Det

Time/Date Setting

Menu Data

System

Exit

How to set the menus

How to set the menus (continued)

Inputting numbers

Number input area

Using the front buttons of the unit:

step

1. Press the number buttons (0 to 9) to input and use

that number.

Time Date Setting

241 000 000

•

The number displayed in red can be changed.

step

2. To move to the next input area, press the 16 button.

0 1

To go back to the previous area, press the 14

button.

Set time and date.

Using a mouse:

step

1. Left-click on the number in red until the needed

Day Light Saving Setting

Auto

Set >

number appears.

To change another area, left-click on the needed

area or left-click or

Return

Setting parameters

step

1. Press the A button or left-click on the parameter box

until the item to be set appears.

•

For some items, more detailed setting is

required. In this case, an item such as “D(Set

>)” is displayed. If necessary, press the D

button or left-click on the “Set >” to set more

details.

When you close the menu, press the E button or left

click on “Return” or “Exit.”

Time Date Setting

241 000 000

You cannot close the menu by pressing the SET UP

button on the unit.

0 1

Set time and date.

Day Light Saving Setting

Auto

Set >

Return

Setting or selecting area

Symbols in the menus

Up button

Menu address

Help button

Motion Search (Main - Normal)

Camera Select

116 000 000

Down button

Left button

Search Start Position

Oldest

0 1

Right button

Setup date search starts from.

Motion Detection Settings

Same as Recording Setting

Next >

Motion A

same

Return

Some symbols appear in the menu screens. The meanings are as follows.

(Help)

When you press the HELP button or click this symbol, the detailed information on the menu appears.

(Left)

(Right)

When you press the 14 button or click this symbol, the item to be set shifts to left.

When you press the 16 button or click this symbol, the item to be set shifts to right.

When you press the 11 button or click this symbol, the value of selected item increases.

When you press the 15 button or click this symbol, the value of selected item decreases.

(Up)

(Down)

Menu address

A unique number for each menu page. You can go directly to each menu page by inputting the menu ad-

dress number using the front buttons of the unit.

For example, when opening the <Motion Search> menu, press the SET UP button and then press the

number button in the order of 1, 6.

How to set the menus

Setting the time and date

Time/Date Setting

This item is used to set the present date, time, and auto day-

light saving. Auto daylight saving function is used to automati-

cally gain the clock of the unit an hour for the speciﬁed time

period.

Start/end time of the auto daylight savings can be checked

and if needed, changed.

Before you start recording, accurately set the present

date and time.

The recording and playback are not performed properly

when the clock of this unit does not run. Check that the

clock of this unit is running before operation.

Setup Menu

System

steps 1, 2

Time/Date Setting

step

Day Light Saving Setting

step

1. Set the present month, date, year, hour, minute, and

second.

2. Select the desired setting for daylight saving.

Auto: Automatically adjust forward or back an

hour for the time period set in the <Day Light

Saving Setting>.

Off: Auto daylight saving function is not used.

step

3. Date and time of Auto Day Light Saving Setting can

be adjusted as needed.

The time is indicated using the 24-hour system.

This unit uses 4 digits to display the year. The

available display range is 37 years between 1/1/2001

to 31/12/2037. The unit is also equipped with a

function to automatically calculate leap years. The year

returns to 2001 after 31/12/2037.

Using the basic multiplexer functions

4. DIGITAL ZOOM button

Basic multiplexer functions

Pressing this button in single screen mode displays the

screen at 100%. At this time, the magnification centre

point (X) appears. Pressing the button again switches

the magniﬁcation to 200%, and then 400%. By pressing

the MOVE buttons, the centre point moves vertically or

horizontally.

This function is used to activate multiplexer functions using

the buttons on the front panel.

DIGITAL ZOOM button

Camera number buttons

When the DIGITAL ZOOM button is pressed, number but-

tons 11, 14, 15, and 16 move the “X” in the screen.

SPLIT screen buttons

SEQUENCE button

OUTPUT A/B button

Move buttons

Multiplexer buttons

1. Camera number buttons (1 to 9)

Displays the picture supplied from the cameras connected

to CAMERA IN terminals 1 to 9 on the rear panel in the

single screen display.

Pictures can be displayed even if the camera is not set to

record.

2. SPLIT screen buttons

Each time the button is pressed, displays the split screen

in the following order.

SPLIT4 ( ) button : SPLIT 4a SPLIT 4b

SPLIT 4c SPLIT 4a • • •

SPLIT9 ( ) button : SPLIT 9 screen

3. SEQUENCE button

Displays the sequential screen in the split screen or

the single screen display. Make the detailed settings of

this display in the <Multiplexer Setting> (Setup Menu

System). Sequential display does not appear during

playback.

The sequential display is cancelled when you press the

SEQUENCE button again or display a different type of

split screen or single screen.

Pressing the OUTPUT A/B button on the front panel

switches the multiplexer video output. When OUTPUT A is

selected, the button light indicator is off. When OUTPUT

B is selected, the button light indicator is on, and camera

number buttons, SPLIT screen buttons, and SEQUENCE

button are operated for the monitor screen connected to

the OUTPUT B connector. Pressing the OUTPUT A/B

button again switches the multiplexer output to OUTPUT A.

Basic operations

Controlling the camera

This function is used to control the cameras connected via

RS-232C or RS-422/485 terminal.

PTZ control using the front panel buttons

step

1. Press the camera number button of the PTZ camera

number to be controlled and display the picture in

the single screen display.

PTZ control using the menu

User Menu

2. Press the PTZ button.

• The unit switches to PTZ mode and the button

lights up. “PTZ” appears on the LCD display on

the front panel during PTZ mode.

PTZ Control

step

Go to PTZ Control

01-01-2006 00:00:00

PTZ

• The camera number to be controlled appears on

the LCD display on the front panel.

Zoom, iris, focus adjustment, AutoPan

step

01-01-2006 00:00:00

PTZ CAM1

Preset

step

3. Control the camera.

Select PTZ Camera

Tilt: Press the TILT

button to tilt the camera in

the upward direction. Press the TILT

tilt the camera in the downward direction.

Pan: Turn the SHUTTLE ring to the right to pan

the camera in the rightward direction. Turn the

SHUTTLE ring to the left to pan the camera in the

leftward direction.

Camera zoom: Press the CAMERA ZOOM button

and then turn the JOG dial to the left (wide) or

right (tele) to adjust the camera zoom.

Focus: Press the FOCUS button and then turn the

JOG dial to the left (far) or right (near) to adjust the

focus of a camera.

button to

step

1. Pan or tilt the PTZ camera connected.

• Click the gray area by using the mouse to adjust

the camera angle.

adjusts the camera angle

in the upward direction

adjusts the

camera angle

in the rightward

direction

camera angle

in the leftward

direction

Iris: Press the IRIS button and then turn the JOG

dial to the left (close) or right (open) to adjust the

iris of a camera.

adjusts the camera angle

in the downward direction

Preset: Press the PRESET button and then press

the number buttons within 3 seconds to preset the

viewing points. Up to 16 points can be set.

Auto pan: Press the AUTO PAN button to activate

the auto pan function of the camera.

step

2. Adjust zoom, iris, and focus. And activate auto pan.

step

3. Preset the viewing points 1 to 16.

• The preset points are registered to the PTZ

camera for auto pan function.

During PTZ operation using front panel buttons, POWER

button and functions related to playback do not work. Fur-

thermore, menus cannot be displayed.

step

4. Switch the camera number to be controlled.

• The camera number to be controlled appears on

the LCD display on the front panel.

01-01-2006 00:00:00

PTZ CAM1

<PTZ Control> can be set using the mouse only. You can-

not set it using front panel buttons.

Recording the picture manually

Setting the recording rate and picture grade for

normal recording

Basic manual recording

This function is to setup the recording parameters of

recording setting pattern A to start recording manually. Ensure

all the cameras are connected and time and date has been

set correctly. Before you start recording, check the repeat

recording settings in the <Data Management Setting for Main

Memory> (System Menu Memory) ﬁrst, and then make the

recording settings.

step

1. Execute camera check.

• The unit automatically detects the cameras

with video signal at their input when you select

“Execute.” The detected cameras are used in

the Auto and Easy settings calculation in step 2.

After executing the camera check, the recording settings

Make the manual recording settings on the <Set

Recording Pattern A (Normal/Timer)>.

are made only for the camera numbers with the video

signal input when using auto or easy setting.

<Set Recording Pattern A (Normal/Timer)> can be used

for manual or timer recording. <Set Recording Pattern B

(Timer)> to <Set Recording Pattern D (Timer)> are used

for timer recording only.

step

2. Set the normal recording menu.

Auto: Automatically sets the picture grade and

the recording rate by setting the recording cycle

and the recording hour per day. Set the desired

settings and then select “Execute.”

• The preview screen appears automatically when

the auto setting is executed.

Settings here are for manual recording only. For timer

recording, settings must be made on the <Timer> menu.

Easy: Sets the frame or ﬁeld recording, recording

rate, and picture grade for normal recording to

the same settings for all the cameras. When the

recording rate is set to “– – –” for all the camera

numbers, normal recording does not perform. Set

the desired settings and then select “Execute.”

• The preview screen appears automatically when

the easy setting is executed.

Setup Menu

Recording

Set Recording Pattern A (Normal/Timer)

step

Manual: Sets per camera, the frame or field

recording, recording rate, and picture grade for

normal recording. When you set “– – –” for the

recording rate, the recording does not perform for

that camera number.

Camera Check

step

• Select “View” to display the preview screen and

check your settings.

Recording Setting A-Normal(Auto)

2 + D

Recording Setting A-Normal

When you set frame recording, the recording rate display

in the preview screen turns green.

Recording Setting A-Normal(Easy)

2 + D

The recording rate display turns red when the value

exceeds 100 pps in total.

Recording Setting A-Normal

Recording Setting A-Normal(Manual)

2 + D

•

The estimated continuous recordable time is displayed

on the bottom of the preview screen which is dependent

on the picture grade and the recording rate settings

for normal recording. (The time does not reflect alarm

recording settings.)

Recording Setting A-Normal

•

When the main device is partitioned, <Estimated

Recording Time> shows the estimated recordable time for

normal recording.

step

3. Press the REC/STOP button.

• The REC/STOP button lights up and recording

starts.

step

4. To stop recording, press the REC/STOP button for

more than 2 seconds.

• Recording stops and the light turns off.

REC/STOP

Basic operations

Playing back the recorded data

step

4. To stop playback, press the STOP button.

• When executing playback again, the playback

starts from the stopped position of the previous

playback.

Basic playback

This function is used to playback recorded data. This unit

allows recorded data to be played back using various

methods. The basic playback described below is the most

common method for playback.

Pressing the OUTPUT A/B button on the front panel

switches the multiplexer video output. When OUTPUT A is

selected, the button light indicator is off. When OUTPUT

B is selected, the button light indicator is on, and the

buttons related to playback function are operated for the

monitor screen connected to the OUTPUT B connector.

Pressing the OUTPUT A/B button again switches the

multiplexer output to OUTPUT A.

step

1. Press the PLAY button inside of the front door.

• Playback starts.

• After turning the power on, the oldest recording

data is played back first. Otherwise, playback

resumes at the stopped position of the previous

playback spot.

STOP PAUSE REV. PLAY PLAY

The playback of each camera may not be executed at a

constant speed depending on the recorded condition.

During the split screen display, the playback speed may

be slower than the speed used for recording.

JUMP TO END

SPEED

When the “Playback Device Repeat Setting” is set to

When playing back on both OUTPUT A and B, the

playback speed may be affected and become slower.

“Repeat Off,” playback stops when reaching the physical

end of the HDD or end point of the recording section.

When the “Playback Device Repeat Setting” is set to

“Repeat On,” recorded data is played back repeatedly.

(System Menu

Setting)

Memory

Recording Data Readout

[To change the playback device:]

step

2^-1. Select the playback device and playback area in the

<Select Source Device>. (User Menu Search)

Main: Plays back the contents from the main HDD

device.

Normal: Normal recording area

Alarm: Alarm recording area

LPA: Long pre-alarm recording area

Copy 1: Plays back the recorded contents of the

copy 1 device.

“SerialBus,” “DVD/CD,” “USBmemory”

Copy 2: Plays back the recorded contents of the

copy 2 device.

“Internal,” “SerialBus,” “DVD/CD”

“Alarm” appears when “Alarm Recording Area” is set

to other than “0 %.” (System Menu

Management Setting for Main Memory)

Memory

Data

“LPA” appears when “Long Pre-Alarm Area” is set to

other than “0 %.” (System Menu

Management Setting for Main Memory)

Memory

Data

step

2^-2. Press the PLAY button.

• Playback of the selected device starts.

When you press the PAUSE/JUMP TO END button during

the playback is stopped, the still frame playback picture

around the end point of the latest recording is displayed.

step

3. To pause playback, press the PAUSE button.

• To resume playback, press the PAUSE button

again or press the PLAY button.

Searching the desired picture

Basic search

This function is used to search the start point of needed

picture. This unit is equipped with 5 search functions (Search

by Time and Date, Search by Alarm List, Find data storage

location, Search by Book Mark, and Search by Motion). In

this section, the common search methods, search by time

and date and search by alarm list, are described.

Search by Time and Date

This item is used to search recording picture by specifying

date, hour, minute, second, and camera number. The search

result is displayed in still frame playback. When searching

for 1 camera number, the search result is displayed in the

single screen display. When searching for 2 or more camera

numbers, it is displayed in SPLIT9 screen.

User Menu

Search by Time and Date

step

1. To input the time and date to be searched manually,

select “Manual” and then set the month, date, year,

hour, minute, and second.

• To input the start and end points of recording,

select “Start” and “End” respectively.

step

2. Set the camera numbers to be searched.

3. Select “Search.”

4. To playback the searched picture, press either the

PLAY button or the PAUSE button.

step

5. To stop playback or still frame playback, press the

STOP button.

To change the source device to be searched, set the

desired device in the <Select Source Device>. (User

Menu Search)

To display the single screen display of the desired camera

number when the search result is displayed in the SPLIT9

screen, press the desired camera number button.

When there is no recording data of the set time, the

picture of the closest time and date for the set camera

number is displayed in still frame.

When the multiple recording data of the same date and

time are existed, execute search by time and date more

than once until the desired picture is searched.

Depending on the recording condition, search by time and

date function may not operate correctly.

When you change the display from single to split or from

split to single during still frame playback, the recording

picture may not be existed at that point or picture may not

be displayed depending on the selected camera number

or timing of displaying the still frame playback picture.

Basic operations

Searching the desired picture (continued)

Search by Alarm List

To clear the alarm list, erase the HDD data of which the

alarm recording is recorded (System Menu Data Clear).

Beware that executing it erases all the data of the HDD

containing the picture data.

This unit stores the start time of alarm recording and

emergency recording in the alarm list when such recording

begins. This item is used to search the desired picture using

the list of alarm recording (emergency recording). The search

result displays in still frame playback of the single screen

display.

Alarm list search is not performed if there are no index

signals.

When alarm recording (emergency recording) is started

while displaying the <Alarm List>, you must ﬁrst exit the

<Alarm List> and then display it again. The new item is

added to the list. In this case, you may have to specify the

date and time to be searched again.

User Menu

steps 1, 2

For alarm list search of LPA area, the list from the start

Search by Alarm List

point of media is displayed when selecting “To latest,”

and the list from the end point of media is displayed when

selecting “ To oldest.”

step

Alarm List

step

1. Set the month, date, year, hour, minute, second,

and sensor number to be searched.

Latest: Displays the date and time of the latest

recording.

2. Select “Alarm List.”

The alarm list may take longer time to display completely

when there are many items in the list.

The displayed alarm list shows the list of alarm recordings

which have been started before and closest to the

speciﬁed time.

step

3. Select the alarm list you want to display.

To change the source device to be searched, set the de-

sired device in the <Select Source Device>. (User Menu

Search)

To execute alarm list search while the “Alarm area” and

“LPA area” are set, set the playback area to “Alarm” and

“LPA” respectively.

“Sensor” display indicates the sensor number to which

the alarm signal is input.

When repeat recording setting for normal and alarm areas

are set to “Repeat Off” and there is an alarm recording

(emergency recording) at the end of the HDD, that

recording may not be stored in the alarm list and that item

may be missed.

When the data of the camera number which is not

corresponded to the alarm sensor number is copied to the

external media, the alarm list of that data is not exactly

similar to that of listed in the digital recorder.

When the detection of the motion or the ground of the

ALARM IN terminal occurs numerously at the same time,

not all the start times of the alarm recording may be

registered in the alarm list. In this case, the sensor of the

lowest number is registered in the list.

In the alarm list, items with the ALARM IN terminal

grounded are indicated in orange, items that were

detected with motion are indicated in white, items with

the EMERGENCY terminal grounded are indicated in

magenta, and items that were input with alarm signal via

communication are indicated in green.

Copying the recorded data

This item is used to copy the data from the main device to a

copy device.

When copying the data to DVD while “Overwrite” is set to

“On,” the unit clears the existing data on the disc before

overwriting with new data. Note that clearing the data

takes about 30 to 40 minutes. You cannot cancel opera-

tion during clearing the data of the DVD.

Copy Data to Copy 1 Drive/Set Copy 1 Drive

This item is used to copy the data to Copy 1 device by speci-

fying the start and end points. The points are specified by

the date and time or the bookmark. This function is useful for

copying the data of the short period of time.

When copying the data while “Copy Data” is set to “Alarm,”

the unit performs copy operation, however, the data is not

copied if there is no alarm recording data within the speci-

ﬁed range of copy. In case of CD/DVD disc, the remaining

capacity becomes low because only the management

information is recorded. It is recommended to carry out

“Calculate” in <Copy Data to Copy 1 Drive> to confirm

whether or not there is alarm recording data in the speci-

ﬁed range.

Before executing the copy, make sure that the Copy 1

device is connected and set in the <Add/Remove HDD

Device> and <Add/Remove DVD/CD Drive> correctly.

(System Menu Memory)

User Menu

step

3. Set the start, start/end, or end point of copy by

specifying the date and time or the bookmark

number.

Copy

steps 4, 5

Start: Sets only the start point of copy. The data

is copied from the specified start point as much

data as possible with the remaining capacity of the

media to be copied.

Copy Data to Copy 1 Drive

step

1 + 2 Range of Copy

Start/End: Sets the start and end points of copy.

End: Sets only the end point of copy. The data

is copied as much data as possible with the

remaining capacity of the media to be copied until

the speciﬁed end point reaches.

• To set the bookmark point, select “Bookmark”

and then select the desired bookmark number.

• To copy from the oldest recording time, select

“Copy Start Time.” To copy to the latest

recording time, select “Copy End Time.”

steps 1, 2

Set Copy 1 Drive

step

1. Set the camera number to be copied.

• The button function changes between “All Off”

and “All On” each time you select this button.

You can switch on and off for all the cameras

easily by using this button.

• The picture is not copied when there is no

recorded picture of the set camera number or

time. Make sure to check that the picture of the

specified camera has been recorded on the

speciﬁed copy start point.

step

4. Select “Calculate” to calculate the capacity of data

to be copied.

When using “End,” the copy cannot be executed unless

the calculation of the capacity of data to be copied is com-

pleted.

step

2. Select “Other settings” and then set the detailed

settings.

When using “Start” or “Start/End” and executing copy

without calculating the capacity of data to be copied, the

progress or the time of the copy may not be displayed

correctly because the unit cannot determine the capacity

of data to be copied.

From Device: Sets the device which contains the

data to be copied. The available setting items are

“Main” and “Copy 2.”

From Group: Sets the group which contains the

data to be copied. The available setting items are

“Normal,” “Alarm,” and “LPA” for main, “SerialBus,”

“DVD/CD,” and “Internal” for copy 2.

step

5. Select “Execute.”

• The copy starts.

• To stop copy manually, select “Cancel” in the

progress screen. The data which has been

copied before cancelling is copied.

To Copy 1: Sets the group to where the data is

copied. The available setting items are “SerialBus,”

“DVD/CD,” and “USBmemory.”

Copy Data: Sets the data area to be copied. The

available setting items are “Alarm” and “All.”

Overwrite: Selects whether or not to overwrite the

existed data.

Auto Eject: Selects whether to eject media (CD/

DVD) automatically when the copy is over.

“Alarm” appears for “From Group” when “Alarm Recording

Area” is set to other than “0 %.” (System Menu Memory

Data Management Setting for Main Memory)

“LPA” appears for “From Group” when “Long Pre-Alarm

Area” is set to other than “0 %.” (System Menu Memory

Data Management Setting for Main Memory)

Basic operations

Copying the recorded data (continued)

When copying the data to DVD while “Overwrite” is set

to “On,” the unit clears the existed data of the disc before

overwriting with new data. Note that clearing the data

takes about 30 to 40 minutes. You cannot cancel opera-

tion during clearing the data of the DVD.

Copy Data to Copy 2 Drive/Set Copy 2 Drive

This item is used to copy the data to Copy 2 device by speci-

fying only the start point. The point is speciﬁed by the date

and time or the bookmark. The copy continues until the end

point of the recording data reaches or the media to be copied

becomes full unless the copy is stopped manually (when “FIFO

Overwrite” is set to “Off”). This function is useful for making

backup of the recording data.

When copying the data while “Copy Data” is set to “Alarm,”

the unit performs copy operation, however, the data is not

copied if there is no alarm recording data within the speci-

ﬁed range of copy. In case of CD/DVD disc, the remaining

capacity becomes low because only the management

information is recorded.

Before executing the copy, make sure that the Copy 2

device is connected and set in the <Add/Remove HDD

Device> and <Add/Remove DVD/CD Drive> correctly.

(System Menu Memory)

Do not use the disc which has been used on the personal

computer, failed to be copied, or stopped during copying

due to the power failure because they may cause mal-

function of the unit.

User Menu

step

3. Set the start time of copy.

Copy

step

Start: Sets the start point of copy.

Continue: Starts copying from the end point of the

previous copy.

• To set the start point using the bookmark,

select “Bookmark” and then select the desired

bookmark number.

Copy Data to Copy 2 Drive

1 + 2 Range of Copy

steps 1, 2

• To copy from the oldest recording time, select

“Copy Start Time.”

Set Copy 2 Drive

step

4. Select “Execute.”

step

1. Set the camera number to be copied.

• The copy starts.

• The button function changes between “All Off”

and “All On” each time you select this button.

You can switch on and off for all the cameras

easily by using this button.

• To stop copy manually, select “Cancel” in the

screen of <Copy Data to Copy 2 Drive>. The

data which has been copied before cancelling is

copied.

• The picture is not copied when there is no

recorded picture of the set camera number or

time.

The warning is displayed when the copied range exceeds

the available capacity of the device to be copied when

“FIFO Overwrite” is set to “Off” and the copy destination

is HDD. In this case, set the copy setting again with nar-

rower copy range or use a copy device with larger capac-

ity.

step

2. Select “Other settings” and then set the detailed

settings.

From Main: Sets the area which contains the

data to be copied. The available setting items are

“Normal,” “Alarm,” and “LPA.”

To Copy 2: Sets the group to where the data is

copied. The available setting items are “SerialBus,”

“DVD/CD,” and “Internal.”

Copy Data: Sets the data area to be copied. The

available setting items are “Alarm” and “All.”

Overwrite: Selects whether or not to overwrite the

existed data.

When the copy is performed during recording, the picture

of the recording start and end points may not be record-

ed.

When the recording data of the main device which is be-

ing copied is about to be overwritten or has been over-

written, copy is stopped. Be careful for the copy which

requires long time such as overwriting copy of DVD.

The progress bar of copy is not displayed for copy 2.

Auto Eject: Selects whether to eject media (CD/

DVD) automatically when the copy is over.

FIFO Overwrite: Selects whether to repeat

copying from the start point of the media by

overwriting the existed data, or to stop copying

when the capacity of the media becomes full

during copying. This setting is available only when

the copy destination is HDD.

The picture data is processed in 2 MB unit. Therefore the

data is copied in 2 MB unit from the start point of the des-

ignated range when copying.

“Alarm” appears for “From Main” when “Alarm Recording

Area” is set to other than “0 %.” (System Menu Memory

Data Management Setting for Main Memory)

“LPA” appears for “From Main” when “Long Pre-Alarm

Area” is set to other than “0 %.” (System Menu Memory

Data Management Setting for Main Memory)

Copying the data of this unit to a video

cassette

This function is used to copy the data of this unit to a video

cassette using an analogue video cassette recorder. Data

can be copied even when the unit is in recording. For the

recording operation, see the instruction manual for the ana-

logue video cassette recorder used.

step

1. [Analogue video cassette recorder] Prepare the

VCR for recording.

• Set the input source of the VCR to the external

input.

step

2. [This unit] Display the picture in its format (single/

split) that you want to record.

step

3. [This unit] If needed, use the search function to

display the start position of copy.

step

4. [Analogue video cassette recorder] Start recording.

step

5. [This unit] Press the PLAY button to start playback.

step

6. To stop copying, press the STOP button on this unit

ﬁrst. And then, stop the recording on the analogue

video cassette recorder.

Only the picture displayed on the monitor screen can be

copied to the video cassette.

Basic operations

Copying the recorded data (continued)

Playback software

Field Reverse

Click to display a still picture one ﬁeld before.

When copying the data to CD/DVD or USB memory, the

needed PC playback software is automatically copied on to

the disc. Refer to the following for using the software.

Stop

Click to stop playback. Audio, if recorded, is played

back after the stop when the audio command has been

enabled.

System requirements

•

OS: Microsoft Windows 2000 or Windows XP.

CPU: IBM PC/AT compatible with an Intel Pentium series

processor of at least 500 MHz.

Field Advance

Click to display a still picture one ﬁeld after.

•

RAM: 256 MB or more.

Playback

HDD: System drive with unused space of at least 200 MB.

Display device: XGA (1024 pixels x 768 pixels) or higher.

Click to playback the picture in the forward direction.

Forward Search

Starting up the application software

Click to playback the picture in the forward direction with

a higher speed than normal playback. The speed changes

from X1 to X2, X4, X8 and back to X1 at every press of

this button during playback.

step

1. Load the CD/DVD/USB memory to the personal

computer which has been used for copy.

2. Double-click the icon of the disc to open.

Camera

(These buttons are displayed when the

button

located on the lower right of the Forward Search button

is pressed.) Click to display the picture of the camera

corresponding to the number of the button. The indicator

turns green for the camera number which is being

displayed, and it turns black for the camera number which

is not being displayed. The picture is not displayed even

when the indicator turns green if the data has not been

copied for that camera number.

step

3. Start up the application software.

• Double-click the “FSM Player Lite.exe.” The

application software starts up and the operation

panel appears.

When the picture cannot be loaded, use the

[Folder] command in the [File] menu to select

the picture folder to be played back.

Refresh Speed

You can open the FSMPlayerLite panel in 4 stages by

(This slider is displayed when the

button located on the

clicking

on the right side. In the ﬁrst stage, you can

lower right of the Camera button is pressed.) Drag with

the mouse to adjust the playback speed. When setting

to [Fast], it may disrupt the operation depending on the

performance of the personal computer used. Use this

setting with the proper picture playback speed suitable to

the personal computer used.

select playback, search and bookmark operations. In the

second stage, you can select a camera to display. In the

third stage, you can adjust playback speed (reducing

only) and in the fourth stage, you can make various set-

tings for audio playback.

The playback speed slider may not be changed at a

constant interval when the data which is additionally

copied is played back.

Output

(This is displayed when the

button located on the

lower right of the Refresh Speed slider is pressed.)

[Not Synchronized playback]

Operational

Panel

Put a checkmark to [Output] on the FSMPlayerLite panel

and select a playback channel from the drop-down menu.

Then select [Not Synchro.] in the [Playback] field. Play

back the copied data and stop at a point where you want

to hear the audio. The audio data around the stop point

are played back. You can change the duration of audio

playback in 3 levels using the slide bar on the right side.

The actual duration of audio playback varies depending

on the frame rate of the recorded picture. Adjust the

duration for every data to be played back.

Operational panel

Rewind

Click to jump to the head of the recording data.

[Synchronized playback]

Select [Synchro.] in the [Playback] field. You can play

back simultaneously the audio and picture of the data

downloaded in blocks via network or the data copied

together with audio by a recorder. Only one playback

channel is displayed in this case. Audio is not played back

during other than normal playback (such as fast-forward

playback and reverse playback). The [LipSync] slide bar

should be adjusted according to the PC to be used and

the recording status of data to be played back. In some

cases, there may not be found an optimum position where

the picture and audio synchronize with each other.

Reverse Search

Click to playback the picture in the reverse direction with

a higher speed than normal playback. The speed changes

from X1 to X2, X4, X8 and back to X1 at every press of

this button during reverse playback.

Reverse Playback

Click to playback the picture in the reverse direction.

In synchronized audio playback, the frequency of picture

refreshing is reduced depending on the processing power

of PC. When you want to playback giving priority to

picture, select [Not Synchro.].

View menu

Picture Size

When clicking, the options of [100%], [75%], [50%], and

[25%] appear. Pictures are zoomed in or out according to

the selected magniﬁcation.

The settings on this panel remain intact for the next start-

up.

Decode Level

Audio playback channel and picture display channel are

not related.

When clicking, the options of [Fine], [Middle], and [Rough]

appear. When setting the decode level to rough, the pic-

ture becomes rough and the playback update speed be-

comes faster.

When data are played directly from a drive that is slow

to read CD and DVD, audio may be output intermittently.

Play back data after copying it to a HDD.

Title Bar

When clicking, the options of [Date Time] and [Alarm] ap-

pear. Put a check mark to the item to be displayed on the

screen.

File menu

Convert

When clicking during the playback is stopped, [Convert]

screen appears. Specify the range to be converted and

the camera number, and then press the [JPEG] or [AVI]

button to convert and save the picture data collectively.

Collective conversion requires adequate free space in the

physical memory and the HDD for temporary files (the

system partition and save drive). The limitations of avail-

able memory space and HDD space vary depending on

your operating conditions.

Grouping menu

Grouping Pattern

When clicking, the [Grouping Pattern] screen appears.

When you click the [4 Multi], [6 Multi], [9 Multi], [10 Multi],

[13 Multi], or [16 Multi], the split screen of the selected

pattern appears. Click “Setting” to display the screen to

set the display position of the camera in each screen.

Perform conversion starting from a small ﬁle that requires

only several seconds to be converted while checking the

state of the memory and the HDD.

Menus appearing with right button clicking

To use the following functions, click the right button of the

mouse on the screen to be operated. The following func-

tions are performed only for the clicked screen.

Search menu

During playback:

When clicking, the [Time Search] screen appears. Specify

the date and time to be searched, and then click the

[Search] button.

The picture of the specified time or around such time

appears. The search may not be performed when the

date and time information of the recorded contents is not

chronological such as the data which is added to the ex-

isting data.

Picture Size

Refer to the section of the “View menu.”

Decode Level

Refer to the section of the “View menu.”

During stopping playback:

Copy

Click to copy the picture being displayed onto the clip-

board.

Operation menu

Save As

For [Playback], [Stop], [Reverse Playback], [Forward Search],

[Reverse Search], [Field Advance], [Field Reverse], or [Re-

wind], refer to the section of the “Operation panel.”

When clicking, the [Save As] screen appears. You can

save the picture being displayed as either a Windows bit-

map ﬁle (.bmp) or a JPEG ﬁle (.jpg).

Picture Size

Bookmark menu

Refer to the section of the “View menu.”

A-, B-

Decode Level

Click to register the current playback position as Point A

or Point B to repeat playback between those positions.

Refer to the section of the “View menu.”

Repeat between A and B

When clicking, the [Print] screen appears.

After setting the [Margins], [Printer Settings...] and other

options, click [Print] button to print the picture being dis-

played.

Put a check mark to repeat playback between Point A and

Point B you speciﬁed.

When playing the data recorded in frame recording, the

outline of the picture may be serrated. In such case,

change the picture size to larger setting.

When loading the media with a lot of picture data copied,

playback software may take time to be started up.

Basic operations

Communications by Web Browser

The Web browser on the personal computer can capture the

pictures that have been recorded and live pictures from the

camera that is connected to this recorder. Also, some of the

recorder settings can be made via the personal computer.

Start up the Microsoft Internet Explorer and log in.

step

1. Start up the Microsoft Internet Explorer and enter

the IP address of the recorder.

• Enter the IP address which is set in <LAN

(Communication) Setting> (System Menu

COM/LAN). When shipped from the factory, the

IP address is set to “192.168.000.100.”

• The “[Login]” screen appears.

The personal computer product requirements

•

OS: Microsoft Windows 98SE, Windows 2000,

Windows Me or Windows XP.

CPU: IBM PC/AT compatible with an Intel Pentium series

processor of at least 500 MHz.

•

RAM: 256 MB or more.

HDD: System drive with unused space of at least 200 MB.

Web Browser Soft: Microsoft Internet Explorer 5.5 or later.

Display device: XGA (1024 pixels x 768 pixels) or higher.

Microsoft and Windows are registered trademarks of the

Microsoft Corporation in the US and other regions.

(The official name of Windows is Microsoft Windows

Operating System.)

All other company and product names appearing herein

are the property of their respective owners.

• Windows 98SE is an abbreviation of Microsoft

Windows 98 Second Edition.

• Windows 2000 is an abbreviation of Microsoft

Windows 2000 Professional.

step

• Windows Me is an abbreviation of Microsoft

Windows Millennium Edition.

2^-1. (When logging in • • • )

First, enter the “User ID” and the “Password.”

When shipped from the factory, the user ID for

the full-rights user is “root,” and the password is

“admin000,” the user ID for the live user is “guest”

and the password is “guest.”

• Windows XP is an abbreviation of Microsoft

Windows XP Home Edition/Professional.

The product requirement described above cannot

guarantee operations in all environments.

More than one user can log in simultaneously using the

same user ID and password.

Lack of compatibility between Web functions and the PC

peripheral driver may, in rare instances, result in abnormal

operation. If this happens, upgrade to the newest version

of Internet Explorer and try again.

However, there are restrictions depending on authoriza-

tion. The maximum number of users that can be connect-

ed at the same time is 10.

Connections

step

2^-2. Select “login” and then left-click or press ENTER.

•

When making a direct connection between this unit and

a personal computer (hereinafter PC), use a cross cable,

and when making a connection through a HUB, use a

straight cable.

• The “[Main Menu]” screen appears.

Refer to the PC instruction manual for instructions on how

to set the Web settings on the PC.

step

3^-1. (If you make an error in entering the user ID or

password • • • )

Main Menu

This is the screen for selecting, from “Main Menu,” “Live

Monitoring” with which live pictures are retrieved and

displayed, “Playback” with which pictures that have already

been recorded are retrieved and displayed, “Configuration

Menu” which allows changes to the settings of the recorder,

“Logout” for ending a job, or “Change Login User” for making

a change in the logged-in user.

• The “[Caution]” screen appears.

step

3^-2. Select “Login” and either left-click or press ENTER.

• The “[Login]” screen appears.

3^-3. Follow step 2-1 and enter the correct “User ID” and

“Password.”

4^-1. (If you do not log in • • • )

Depending on the user’s authorization, there are certain

menus that cannot be selected.

Select “If you won’t log in, please go to Logout.” and

left-click.

The transfer rate at communication changes depending

on the communication environment or unit’s status. For

stable communication, use this unit with the proper image

transfer speed suitable to the conditions of the communi-

cation line.

step

4^-2. The message “Session ID removed from recorder

& browser. Please close the browser.” is displayed.

Close the Web Browser at this point.

5^-1. (To change password • • • )

The user’s session ID (connection data) is lost in 5 min-

utes from the ﬁnal operation that includes picture retrieval.

If no operations are made within that 5 minutes, no other

operations can be made after that so close the browser

and then log in again.

The password can be changed in the “[Login]”

screen only by the user who has the authorization

to change a password. Follow the instructions

in the menu and enter the current “User ID” and

“Password.”

If the unit’s MAIN switch is “OFF,” live and recorded pic-

tures cannot be retrieved.

step

5^-2. Enter the new password in “New password” and

again in “New password (Conﬁrmation).”

step

1. Select the desired menu from “Main Menu” and left-

click.

The number of characters that can be used in registering

a password is 16. Both alphabet letters and numbers can

be used with a distinction made between upper and lower

case. You cannot use spaces.

step

5^-3. To change to a new password, select “change” and

left-click or press ENTER. To cancel the change,

select “clear” and left-click or press ENTER.

Communications by Web Browser

Communications by Web Browser (continued)

Live Monitoring

Retrieves live pictures and displays the pictures on the PC

screen.

step

1. Select “Live Monitoring” and left-click.

• The “[Live]” screen appears.

When picture acquisition is tried for the first time with

the Web browser of a personal computer, a message as

shown below may be displayed. If it is displayed, click

“Yes.”

STOP

: Stops the retrieval of an picture.

: Starts (or restarts) the retrieval of an pic-

ture.

Display

Layout

: For selecting either the display or non-

display of a camera number.

: For selecting from the 12 types of display

patterns.

(default: 4(1-4) screen)

Camera

: Selects the camera number that you want

to display and check.

When the unit is recording at the full rate (100 pps), the

picture supplied from the camera which is not used for

recording at that time may not be updated.

Transfer Rate : Selects one of 5 stages from “Lo” to “Hi”

for picture retrieval speed.

(default: middle)

Save Layout

: The layout of the screen display is regis-

tered to “Local PC.”

Main Menu

Logout

: Returns to the “Main Menu.”

: For logging out.

Setting “Transfer Rate” to “Hi” may present a problem

to the PC operations. This could be due to the PC’s

hardware/software performance you are using. Adjust the

image transfer rate that best meets your machine.

Depending on the network capacity and the load

conditions, the transfer rate may be affected.

Picture may vibrate vertically when displaying the live

picture of the camera of which picture is set for frame

recording.

Playback

The following searches can be selected in single-screen

display.

Retrieves, plays back and searches for pictures that have

been recorded by the recorder.

step

1. Select “Playback” and left-click.

• The “[Playback]” screen appears.

The function of searching for recorded picture data is

effective only when the single-screen display has been

selected in the “Playback” menu. The function cannot op-

erate during picture data playback so to make a search of

any type ﬁrst stop the playback.

step

2. Press the button.

Time Search

• Playback starts.

: Press to start playback.

Select the date and time and click “Search.”

: Press to start speed search in the forward direc-

tion at speeds of x2, x4, x8 and x16.

: Press to frame-by-frame playback in the forward

direction.

: Press to start reverse playback.

: Press to start speed searches in the reverse direc-

tion at speeds of x2, x4, x8 and x16.

: Press to frame-by-frame playback in the reverse

direction.

: During playback or searching, press to stop play-

back for still frame.

Device : Selects the HDD for playback and search.

(default: Normal)

The date, time, and the camera number for the picture ac-

quired are displayed in “Image Information.” Clicking “Save

Image” stores the picture that is still-frame displayed in

the PC in bit map format.

Communications by Web Browser

Communications by Web Browser (continued)

Alarm List Search

Conﬁguration Menu

Click “Alarm List” and the “Alarm List Search” screen appears

in the sub-screen.

This is the screen for making some of the recorder settings.

step

1. Select “Configuration Menu” in the “[Main Menu]”

screen.

• The “[Conﬁguration Menu]” screen appears.

step

1. Set the desired date/time and number of alarm list

items to be acquired, and then click “Refresh” to

acquire the alarm list.

step

• The alarm list cannot be acquired without

clicking “Refresh.”

2. Select the desired “Configuration Menu” and left-

click.

• Enter the needed number of alarm list items to

be acquired in “Alarm Cnt.” If number entered is

too large, depending on the recording condition,

it may take a long time to acquire the list or

the desired number of list items may not be

acquired.

• “Sensor”: Check the desired sensor number for

acquiring the alarm list items.

step

2. Select the “No.” desired, and then click “Search.”

• Click “Prev(number)” for a search in the reverse

direction and click “Next(number)” for a search

in the forward direction.

• Click “Refresh” again to re-acquire the “Alarm

List,” and click “Close” to hide the “Alarm List

Search” menu.

Image Search

Click to display the picture of the next alarm list item.

Click to display the picture of the previous alarm list item.

step

User Registration

2^-2. (To change settings • • • )

This is the screen for changing the settings for registered

user authorization, and for deleting a registration. It can also

be used for registering new users.

Select “change” and left-click. The “[Change

Conﬁrmation]” screen appears.

step

2^-3. If you want to make the change, left-click “change.”

step

1. Select “User Registration” and left-click.

If you want to cancel a change, left-click “cancel.”

• The “[User Registration]” screen appears.

2^-4. (When you have selected “change” • • • )

The “[Completed]” screen appears, so then left-click

“User Registration.”

• The “[User Registration]” screen reappears.

step

2^-5. (When you have selected “cancel” • • • )

• The “[User Registration]” screen reappears.

3^-1. (To delete a registered user • • • )

Left-click on “remove” in the user ID that you want

to delete in “Change authorities of users.”

• The “[Remove Conﬁrmation]” screen appears.

step

3^-2. If you want to delete it, left-click “remove.” If you

don’t want to delete it, left-click “cancel.”

3^-3. (If you have selected “remove” • • • )

The “[Completed]” screen appears, so left-click “User

Registration.”

• The “[User Registration]” screen reappears.

step

2^-1. (To change registered user settings • • • )

step

3^-4. (If you have selected “cancel” • • • )

Select the user ID for changing the settings in the

“Change authorities of users” settings.

• Select the items that you want to change.

• The “[User Registration]” screen reappears.

4^-1. (To register a new user • • • )

Enter the new user ID and new password in “Add

New User.”

Live Monitoring

: Allows viewing of live pictures. It is a

mandatory rank to be registered.

step

4^-2. Refer to step 2-1, select the “Authority” desired and

put a check mark.

Playback

: Allows viewing of recorded pictures.

A user ID with the same name cannot be registered. The

maximum number of characters that can be used in reg-

istering a password is 16. Both alphabet letters and num-

bers can be used with a distinction made between upper

and lower case. You cannot use spaces.

All Cameras

: Allows viewing of pictures from all the

cameras. (The picture of the cam-

eras set to “Off” in the covert camera

setting can also be displayed.)

Change Passwords : Allows changing of user’s password.

step

4^-3. If you want to make a new registration, left-click

“register.” If you want to cancel a new registration,

left-click “clear.”

Configuration

: Allows viewing and editing of user

registration information.

step

Certain items cannot be selected depending on what the

user authorization is.

4^-4. (If you have selected “register” • • • )

It is added to “Change authorities of users.”

4^-5. (If you have selected “clear” • • • )

Clears the speciﬁed contents.

“Configuration” authorization can be used by only one

user. From the time that a user logs in until that user logs

out and gives up authorization, any other user that logs in

is regarded as a user who does not have “Conﬁguration”

authority.

“Playback” authorization can only be used by one user.

From the time that a user logs in until that user logs out

and gives up authorization, any other user that logs in is

regarded as a user who does not have “Playback” author-

ity.

Communications by Web Browser

Communications by Web Browser (continued)

E-mail Setup

Recorder Title & Camera Titles

This is the screen for setting the information related to the

e-mail server or sender, and for setting the e-mail address of

the receiver.

This is the screen for setting or changing the recorder and

the camera titles.

step

1. Select “Recorder Title & Camera Titles” and left-

step

1. Select “E-mail Setup” and left-click.

click.

• The “[E-mail Setup]” screen appears.

• The “[Recorder Title & Camera Titles]” screen

appears.

step

2. (When making the settings to send the e-mail • • •)

step

2. Enter the desired recorder or camera title to “New

Input the desired settings for “SMTP Server (Host

Name or IP),” “POP Server (Host Name or IP),”

“POP User ID,” “POP User Password,” “DNS Server

1 Address,” “DNS Server 2 Address,” “From:,” and

“Recorder ID.”

Text.”

• The recorder and the camera titles currently set

are shown in the “Current Text.”

step

3. Select “change” and left-click.

• The settings currently set are shown in the

“Current Settings.”

The maximum number of characters that can be used to

set the e-mail address is 49.

step

3. To send the test e-mail, select “From Address Test

(send test mail)” and left-click.

step

4. (When attaching alarm recording picture to e-mail •

• •)

Put a check mark on “Picture” checkbox.

• E-mail with the picture which is captured during

alarm recording is sent to the marked user. The

file extension of the picture data file which is

attached to e-mail is “.aap”.

• “Delay time to attachment” is used to determine

the timing of capturing the picture to be

attached. The time period between occurrence

of alarm and capture of the picture can be set

up to 10 seconds.

You cannot send the picture when the alarm recording is

not performed.

The picture to be attached is captured during alarm

recording of which trigger is input of the rear terminal.

To perform this function, put a check mark on “Sensor.”

When the multiple notiﬁcations are occurred at the same

time, notiﬁcation may be delayed or not all the items may

be notiﬁed.

When the alarm recording time is shorter than the

speciﬁed delay time, the picture cannot be attached.

When the multiple alarm signals are input at the same

time, only the picture from the camera corresponding to

the lowest sensor number is attached.

To view the attached picture:

In the PC with DX-PC55E (version 2.1 or later) installed,

click or double click the ﬁle.

In the PC without DX-PC55E installed,

drag the ﬁle and drop it into the “MPicViewer.exe” which

is stored in the supplied CD.

The displayed picture can be printed or can be saved in

general image formats.

step

5^-1. (When setting the receiver’s address • • •)

Enter the desired e-mail address to “New Address.”

5^-2. Set the contents to be transmitted from the recorder

to the PC.

• “Remain,” “Temp/Fan,” “Reboot,” “Record,”

“Alarm,” and “Sensor” settings can be set.

step

5^-3. Select whether to activate or inactivate the e-mail

address you have set.

• When a check mark is put to “Active” column,

the selected e-mail address becomes active.

step

5^-4. Select “set” and left-click.

5^-5. Select “send” to send the test e-mail.

When the e-mail notifications or IP notifications have

been occurred frequently, the operation of the recorder

may become unstable.

Communications by Web Browser

Communications by Web Browser (continued)

Access Mode Setup

Clock Setup

This is the screen for changing the SSL settings.

This is the screen for setting the clock of the recorder via PC.

step

1. Select the item to be changed in the “Access Mode

1. Select “Clock Setup” and left-click.

• The “[Clock Setup]” screen appears.

Setup.”

• Use SSL for Web Access:

Sets the level of the encoding function (SSL).

“No SSL”: Does not use the encoding function.

“Menus only”: Uses the encoding function for the

menus only.

“Menus + Pictures”: Uses the encoding function

for the menus and pictures.

• SSL Port Settings:

Sets the port number used for SSL communication.

• Band-Width Limit:

Controls the band width of the communication.

step

2^-1. Set “Month,” “Date,” “Year,” “Hour,” “Min.,” “Sec.,”

“Time Zone” to the desired time.

step

2^-2. Select “set” and left-click.

step

3. (When setting the clock using “Synchronize with

PC’s clock” • • •)

When you want the clock of the recorder to be

synchronized with the PC clock, select “Synchronize

with PC’s clock” and left-click.

• The clock of the recorder is set to the same time

as that of the PC.

When you use SSL, the following message appears. Se-

lect “Yes” and then continue the operation.

• When using this function on the timing that the

year, month, day, hour, or minute is changed,

check the clock after synchronizing with the PC

clock.

step

4. (When setting the daylight saving time function • • •)

Select “No” when you do not want to use the

daylight saving time function.

Select “Auto” to use the daylight saving function.

• When selecting “Auto,” set the desired time

period for activating the daylight saving time

function and then select “set.”

When displaying live or playback picture while “Use SSL

for Web Access” is set to “Menus only,” the following mes-

sage appears. Select “Yes” to display the live or playback

picture.

In this case, the key-shaped icon which shows the

encoded communication of the browser is not displayed,

however, communication is carried out with encoded.

step

2. Set the desired setting in “New Settings” and then

select “change” and left-click.

Logout

Change Login User

In this screen, assign “Logout” settings to end the job.

This screen is for changing the logged in user.

step

1. Select “Logout” and left-click.

1. Select “Change Login User” and left-click.

• The “[Logout]” screen appears.

• The “[Login]” screen appears.

step

2. Close the Web Browser.

If the browser is closed incorrectly (not logging out cor-

rectly), the user’s session ID is saved for 5 minutes. If the

utes, operation limits may take effect.

step

2^-1. (To change the logged in user • • • )

In the “Login (or change login user)” settings,

execute step 2-1 and 2-2 in “ Login” and change

the logged in user.

• The logged in user is changed and the “[Main

Menu]” screen appears.

step

2^-2. (To log in without changing the user • • • )

Select “Return” button on the browser and left-click.

step

2^-3. (To log out • • • )

Select “If you won’t log in, please go to Logout.” and

left-click.

Communications by Web Browser

Troubleshooting

If problems with the unit persist even after you’ve followed the suggestions below, disconnect the power cord and contact the

retailer from whom you purchased the unit.

Description of problem

Consult the following

The unit does not be turned

on.

• Is the power cord properly plugged in?

• Is the LOCK indicator light on?

• Is the TIMER indicator light on?

• Is the MAIN switch on the rear of the unit set to “OFF” ?

• Is the LOCK indicator light on?

Power is on, but the unit

does not operate.

• Is the POWER indicator flashing? (The unit cannot be operated while the POWER

indicator is flashing.)

• The safety features may be in operation.

Reset the unit by pressing the RESET button on the rear panel using a ballpoint

pen or similar object, and then turn the power on again.

• Are the monitor and camera(s) connected correctly?

• Is the unit receiving an input signal from the selected camera?

Check this by displaying the SPLIT9 screen.

Pictures are not appearing

on the monitor.

The quality of the monitor

picture is poor.

• Is the connecting cord connected correctly?

• Is the camera’s focus adjusted correctly?

The unit does not start

recording.

• Is repeat recording set to "Repeat Off"?

• The recording starts after the time set for recording rate is passed.

Was the unit stopped during that time?

The unit does not stop

recording.

• Is the LOCK indicator light on?

• During normal recording, alarm recording, and emergency recording, press the

REC/STOP button for more than 2 seconds.

• Is timer recording in progress?

To stop timer recording, press the TIMER button for more than 2 seconds.

• Is repeat recording set to "Repeat On"?

The unit does not repeat the

recording.

The unit does not perform

timer recording.

• Are the date and current time set accurately?

• Are the recording start-/end-times and the recording rate set correctly?

• Is repeat recording set to "Repeat Off"?

The unit does not perform

alarm recording.

• Is the recording rate for alarm recording set to “– – –”?

• Is the recordable capacity for alarm recording area full?

• Is the unit in timer recording stand-by mode?

(Is the TIMER indicator light on?)

• Are the peripheral switches, etc., connected correctly?

Description of problem

The unit does not perform

playback.

Consult the following

• Is the LOCK indicator light on?

• Has the data been erased?

• Is the correct playback device selected?

The copy device dose not

respond.

• Has the recording medium been inserted correctly into the unit?

• Is the unit currently in the middle of loading the recording medium?

• Is the correct playback device selected?

• Has the recording medium's write-protect been removed?

• Is the power supply of peripheral recording device set ON?

• Is the copy device registered in the <Add/Remove HDD Device> or

<Add/Remove DVD/CD Drive>?

The camera cannot be

controlled via this unit.

The unit does not perform

the motion detection

function.

• Is the camera to be controlled connected correctly?

• Is the <PTZ Setting> menu set correctly?

• Is trigger for alarm recording of the camera number for which the motion

detection function to be executed set to “External” ?

• Is the alarm recording rate of the camera number for which the motion detection

function is executed set to “– – –”?

• Is the value set in “Motion Threshold” of the <Motion Det> menu larger than that

of “Motion Mask Settings” ?

• Is the detection area set correctly?

The unit cannot be controlled

via the personal computer.

• Is the <COM/LAN> menu set correctly ?

• Are the unit and the personal computer connected correctly ?

• Is there a defect in the connecting cable ?

• Is the proper connecting cable being used ?

There is a camera number

with a blue screen during

split screen display.

Button operation is not

working.

• The screen of camera number with no video signal input appears blue even when

setting for operation.

• Is the POWER indicator flashing?

(The unit cannot be operated when the POWER indicator is flashing.)

• Is the LOCK indicator light on?

Cameras cannot be

switched with the

• Is the menu screen being displayed?

Camera number buttons cannot be used when the menu screen is displayed.

camera number buttons.

Menus cannot be set.

• When OUTPUT B is selected, the cursor of the mouse is displayed, however, the

menu screen is not displayed and cannot be set. The menus can be set only

when the OUTPUT A is selected.

Following functions do not

work:

• Is section download function (the function to copy the picture data remotely using

the supplied application software, DX-PC55E) performed via communication?

The functions described to the left are not performed while section download

function is in use.

• Copy1

• Deletion of copy 1 device

data

• Loading/Saving menu

• Restore

• Picture copy

Troubleshooting

Warnings and CALL OUT output

Warnings and their appropriate countermeasures

#1 Options in the CALL OUT output column:

•

Selectable: Selects to output CALL OUT signal or not on the menu screen.

Fixed: Outputs CALL OUT signal from the CALL OUT terminal regardless of the menu setting.

None: Does not output CALL OUT signal, but displays a warning on the screen.

The warning display appears when the HELP button is pressed during “ALERT” is displayed on the screen. The contents

of last 16 warnings are stored and can be displayed. The contents older than them are cleared and output of CALL OUT is

cancelled. CALL OUT signal output can be stopped by pressing the E button or clicking “Clear Warning” while displaying

the warning display.

CALL OUT

output

Cancelling

the warning

Log number

Countermeasure

Warning Display

The remaining capacity of Normal Area

in Main device has become less than **%.#2

The remaining capacity of Alarm Area

in Main device has become less than **%.#2

The remaining capacity of LPA Area

in Main device has become less than **%.#2

The remaining capacity of Copy 2 disk

has become less than **%.#2

• Copy data as necessary.

Click "Clear

Warning" or

press the E

button.

Selectable

LOG1200

LOG1201

LOG1202

LOG7200

The remaining capacity of Normal Area

in Main device has become 0%.

The remaining capacity of Alarm Area

in Main device has become 0%.

The remaining capacity of LPA Area

in Main device has become 0%.

• When the warning is cancelled,

the unit starts overwriting the

oldest data remaining in the

HDD.

Click "Clear

Warning" or

press the E

button.

Selectable

None

Selectable

None

LOG1100#3

LOG4100#4

LOG1101#3

LOG4101#4

LOG1102

• Copy data as necessary.

Selectable

The remaining capacity of disc in Copy 1

drive has become 0%.

The remaining capacity of disc in Copy 2

drive has become 0%.

• Replace media if necessary.

Click "Clear

Warning" or

press the E

button.

Click "Clear

Warning" or

press the E

button.

None

LOG3100

LOG7100

Selectable

None

Copy data size error.

• Set the copy/restore range again.

• Replace with new media.

LOG3701#5

LOG7701#6

LOG4701#4

Check the range of copy data or the disk space

of copy media.

Copy media error.

• Check that media is in the

recording device. (If not, insert

the media.)

Click "Clear

Warning" or

press the E

button.

None

LOG3702#5

LOG7702#6

LOG4702#4

Cannot copy the data.

Check the copy device.

•

Check whether that the write-protect

of the media is enabled. Is so,

cancel the protection.

• After turning off the power of the

peripheral recording device and

the unit, reboot in order of

peripheral recording device and

the unit.

• After turning off the power of the

peripheral recording device and

the unit, check a cable.

No disk.

• Insert the disc.

Click "Clear

Warning" or

press the E

button.

Click "Clear

Warning" or

press the E

button.

None

LOG3703#5

LOG7703#6

LOG4703#4

The drive has no disk or wrong type of disk.

Put a proper disk into the drive.

The remaining capacity of disc in Copy 1

drive has become 0%.

Put a new disk into the drive.

The remaining capacity of disc in Copy 2

drive has become 0%.

• Replace the disc.

LOG3704#5

LOG7704#6

Put a new disk into the drive.

(The following numbers are entered in

)

01 : CH 1 02 : CH 2 03 : CH 3 04 : CH 4

05 : CH 5 06 : CH 6 07 : CH 7 08 : CH 8

09 : CH 9

#2 : The value depends on the setting.

#3 : Log number for recording

#4 : Log number for restore

#5 : Log number for copy 1

,14

,34

,74

: Recording

: Copy 1

: Copy 2

,24

,44

: Playback

: Restore

#7 :

#8 :

(The following numbers are entered in

00 : A (Internal) 01 : B (Internal)

10 to 25 : USB (External)

)

#6 : Log number for copy 2

CALL OUT

output

Cancelling

the warning

Log number

Countermeasure

Warning Display

No Camera Signal

Stop recording.

• Check whether the unit and

camera are properly connected

and turned on.

• Check whether the video signal is

being properly outputted.

• Check whether the camera with

no video signal input is set for

operation.

• Continue the operation when

there is no abnormality.

• When the error occurs

continuously, check the

HDD/media and cable and then

restart the unit.

Fixed

LOG54

Camera signal is lost or distorted.

Please check the camera and cable

connection.

Output video

signals.

Click "Clear

Warning" or press

the E button.

Automatically

clears after 1

minute.

It can use as it is though a slight error

occurred.

None

Fixed

LOG13

LOG33

LOG43

LOG73

LOG23

Click "Clear

System suspended due to unstable

• Restart the unit.

LOG14

Warning" or press

the E button.

processing. Recording will be resumed.

HDD

was disconnected.

System suspended due to unstable

processing. Start operation again.

LOG74

LOG24

LOG34

LOG44

LOG55

Automatically

clears after 1

minute.

None

Fixed

Click "Clear

The recorder detected the data altered or data

recorded by other recorder.

Warning" or press

the E button.

Click "Clear

Warning" or press

the E button.

Click "Clear

Warning" or press

the E button.

Click "Clear

Warning" or press

the E button.

Click "Clear

Recorder detected technical problems

on the device.

LOG6200

LOG5100

LOG5200

LOG5201

The recorder has been rebooted. The problem • Check the unit.

is not critical, but check the recorder.

Internal temperature is getting too high,

check the ventilation of the recorder.

• Turn off the power and change

the installation condition.

Internal temperature is getting too high,

stop the operation of the recorder

immediately.

• Turn off the power and change

the installation condition.

Warning" or press

the E button.

Lower the

temperature.

Click "Clear

Warning" or press

the E button.

Rotate the fan.

Click "Clear

Warning" or press

the E button.

Click "Clear

Warning" or press

the E button.

The fan of the recorder needs to be checked. • Turn off the power and stop

using.

Fixed

LOG5300

Copying data stopped because of new record • Stop HDD recording to continue

None

LOG3500#5

LOG7500#6

overwrites the old data.

copy/backup.

New record will soon overwrite the old data

in copying.

• Stop HDD recording to continue

copy/backup.

LOG3600#5

LOG7600#6

Stop the recording, if you want to continue the • Stop copy/backup to continue

copying.

(NONE)

HDD recording.

• Restarts by watchdog operation

or for self-recovery.

–

LOG5101

LOG5102

LOG5103

Regarding LOG14 : Displays during recording. The system shuts down once and then resumes recording. (The error HDD is

automatically deleted from the recording device. The recording is continued until all the registered HDDs are used up.)

Regarding LOG24

to 74 : Displays during copying or playback. The playback or copy stops because the system shuts down.

Carry out playback or copy again.

Regarding LOG 54 : Displays during recording when the video signal is not existed for the camera being recorded for 2 seconds

or more. This warning may not be displayed for the recording of which recording time is less than 2 seconds.

Warnings and CALL OUT output

ITALY

Mitsubishi Electric Europe B.V.

UK Branch Ofﬁce

Mitsubishi Electric Europe B.V.

Italian Branch Ofﬁce

Visual Information Systems Division

Travellers Lane Hatﬁeld Herts AL10 8XB

Centro Direzionale Colleoni

Palazzo Perseo - Ingresso 2, Via

Paracelso 12, 20041 Agrate Brianza, Italy

Telephone: +44 (1707)-278 684

Fax: +44 (1707)-278 541

Telephone: +39 (039)-605 31

Fax: + 39 (039)-605 3214

GERMANY

Mitsubishi Electric Europe B.V.

German Branch Ofﬁce

Electric Visual Systems

The Netherlands

Mitsubishi Electric Benelux

A Division of Mitsubishi Electric Europe B.V.

Niiverheidsweg 23A, 3641 RP Mijdrecht

Netherlands.

Gothaer Str. 8 40880 Ratingen Germany

Telephone: +49 (2102)-486 9250

Fax: +49 (2102)-486 7320

Telephone: +31 (297)-282 461

Fax: +31 (297)-283 936

SPAIN

Mitsubishi Electric Europe B.V.

Spanish Branch Ofﬁce

Ctra. de Rubi, 76-80 Apdo.420

08190 Sant Cugat del Valles

(Barcelona) SPAIN

Sweden

Mitsubishi Electric Scandinavia

Hammarbacken 14 Box750 SE-191 27

Sollentuna

Sweden

Telephone: +34 (93)-565 3154

Fax: +34 (93)-589 4388

Telephone: +46 (8)-625 1000

Fax: +46 (8)-35 1132

FRANCE

Ireland

Mitsubishi Electric Europe B.V.

French Branch Ofﬁce 25,

Boulevard des Bouvets 92741 Nanterre

Cedex

Mitsubishi Electric Ireland

A Division of Mitsubishi Electric Europe B.V.

Westgate Business Park, Ballymount,

Dublin 24. Ireland

Telephone: +33 (1)-5568 5500

Fax: +33 (1)-5568 5731

Telephone: +353 (1)-419 8800

Fax: +353 (1)-419 8895

872C423A1

PRINTED IN MALAYSIA

IBM THINKCENTRE 8141 User Manual
JVC AV 24F704 User Manual
JVC AV28S2EI AV32S2EI User Manual
KitchenAid Cooktop KGCU462V User Manual
KitchenAid KECC501B User Manual
Miele KM 5753 User Manual
Moffat RN8803G RB User Manual
Omega Speaker Systems CIO RELAY32 User Manual
Philips HWC7190A User Manual
Philips LCD MONITOR 170C5 User Manual