Miele CS1221 User Manual

Operating and Installation

Instructions

Ceramic combiset with Induction

CS 1221

en - US

To prevent accidents and

appliance damage,

read these instructions

before

installation or use.

M.-Nr. 07 346 540

IMPORTANT SAFETY INSTRUCTIONS

Children

WARNING- When using your

Activate the Child Safety Lock so

that the combiset cannot be turned on

appliance follow basic

precautions, including the

following:

inadvertently.

Children should not be left

Read all instructions before

installation or use to prevent

injury and appliance damage.

unattended in an area where the

appliance is in use. Never allow

children to sit or stand on any part of

the appliance.

Caution: Do not store items of interest

to children in cabinets above the

appliance. Children climbing on the

appliance to reach these items could

be injured.

This appliance conforms to all

uniform safety codes and

regulations.

Keep these operating instructions

in a safe place and pass them on

to any future user.

The appliance is hot during use and

remains so for some time after being

switched off. Keep children away from

the appliance.

SAVE THESE INSTRUCTIONS

Ensure that any packing material, is

Correct usage

disposed of safely and kept out of the

reach of children. Danger of

suffocation!

Only use the combiset for residential

cooking, and for the purposes

described in this manual.

Other uses are not permitted and can

be dangerous.

Keep all pots and pans out of the

reach of children. Danger of burning or

scalding.

Persons who lack physical, sensory

or mental abilities, or experience with

the appliance should not use it without

supervision or instruction by a

responsible person.

IMPORTANT SAFETY INSTRUCTIONS

Technical Safety

Before servicing, disconnect the

appliance from the main power supply.

Installation, repair and maintenance

work should be performed by a Miele

authorized service technician. Work by

unqualified persons could be

Do not operate any appliance with a

damaged cord or plug, or if the

appliance has been damaged in any

manner. Contact Miele’s Technical

Service Department.

dangerous and may void the warranty.

Be sure your appliance is properly

installed and grounded by a qualified

Under no circumstances open the

outer casing of the appliance.

technician.

Before installing the combiset,

check for externally visible damage.

The combiset must not be installed

outdoors.

Do not operate a damaged appliance.

While the appliance is under

warranty repairs should only be

To guarantee the electrical safety of

this appliance, continuity must exist

performed by an authorized service

between the appliance and an effective technician. Otherwise the warranty is

grounding system. It is imperative that

this basic safety requirement be met. If

there is any doubt, have the electrical

system of the house checked by a

qualified electrician.

void.

In the event of any damage to the

appliance, it must be turned off

immediately and disconnected from the

main power supply. Contact Miele’s

Technical Service Department.

Do not use the appliance until it has

been repaired. Ensure power is not

supplied to the appliance until repair

work is completed.

Before installation, make sure that

the voltage and frequency listed on the

data plate correspond with the

household electrical supply. This data

must correspond to prevent injury and

appliance damage. Consult a qualified

electrician if in doubt.

Defective components should be

replaced by Miele original spare parts

only. Only with these parts can the

manufacturer guarantee the safety of

the appliance.

Do not use an extension cord to

connect this appliance to electricity.

Extension cords do not guarantee the

required safety of the appliance.

IMPORTANT SAFETY INSTRUCTIONS

Do not cook on a broken combiset.

The appliance gets hot when in use

~ ~

Any breakages or cracks in the ceramic and remains hot for quite a while after

surface of the appliance are defects

and must be treated as such. If the

combiset should break, cleaning

solutions and spills may penetrate the

broken combiset and create a risk of

electric shock. Do not use the

being turned off. As long as the surface

temperature is high enough to cause a

burn, the Residual Heat Indicator will

remain lit. Once sufficient time has

passed and the combiset surface is

safe to touch, the Residual Heat

Indicator will go out.

appliance until it has been repaired.

Do not use the appliance until it has

been properly installed in the

Protect your hands with oven mitts

or potholders when using the

countertop.

appliance. Use only dry, heat resistant

potholders. Moist or damp potholders

used on hot surfaces can result in

steam burns. Do not let the potholder

touch the hot heating elements. Do not

use towels or other bulky items near the

appliance.

Be sure that the power cord does

not come in contact with any "hot spots"

after installation.

Safety

Individuals with a pacemaker or

similar medical device:

Do not heat unopened containers.

Built-up pressure may cause the

Please note that an electromagnetic

field develops when the combiset is

turned on. It is not likely that this will

affect the pacemaker or similar device.

If in doubt contact the manufacturer of

the device or your doctor.

container to burst and result in injury.

Do not flambé under an exhaust

hood. Flames could be drawn up into

the hood by the suction and the grease

filters may ignite.

Keep magnetized items, e.g. credit

cards, disks, etc. away from the

combiset while in operation. Damage

may result.

IMPORTANT SAFETY INSTRUCTIONS

Do not use the appliance until it has

been properly installed in the

Never cover the appliance with a

cloth. A fire may result.

countertop.

Be aware of loose fitting or hanging

Do not store items on the appliance

garments when operating the

appliance, they may present a fire

hazard.

when not in use. Items could melt or

catch fire from residual heat or if the

appliance is turned on inadvertently.

Always switch the burner(s) off after

use.

Never leave a combiset unattended

at high settings or when cooking with oil

or fat. Overheated oil could ignite.

Always heat oil slowly, monitoring it as it

heats.

Do not store aerosols, combustibles

or any other easily flammable materials

underneath or adjacent to the

appliance.

Never heat an empty pan unless the

pan manufacturer states that you can

The combiset is fitted with a cooling

do so.

fan. Drawers under the combiset are

not recommended. If a drawer is fitted

directly underneath the combiset,

ensure that there is sufficient space

between the drawer, its contents and

the underside of the appliance in order

to ensure sufficient ventilation for the

combiset. Do not store small items or

paper in the drawer. They could get

sucked into the housing by the fan and

cause damage or impair cooling.

Do not use water on grease fires.

Smother or use a dry chemical or

foam-type extinguisher on any fire or

flame.

Make certain that the power cords of

small appliances do not come in

contact with the appliance. The

insulation of the cable could become

damaged. Danger of electric shock!

Be careful not to drop anything on

Ensure that no aerosols, combustible

liquids or other flammable materials are

kept in this drawer. If cutlery inserts are

to be placed in the drawer they must be

made of heat-resistant material.

the ceramic surface of the combiset.

Even lightweight objects may cause

damage.

Pot and pan handles should be

turned inward and not extend over the

countertop to reduce the risk of burns,

ignition of flammable materials, and

spills.

Metallic items kept in a drawer

under the combiset can become hot

when the appliance is used for a longer

period of time. Use caution.

If the combiset is installed above a

pyrolytic oven it should not be used

during the pyrolytic process. The

overheating protection feature of the

combiset might be activated.

IMPORTANT SAFETY INSTRUCTIONS

Be careful not to drop anything on

the ceramic surface of the combiset.

Do not allow solid or liquid sugar,

pieces of plastic or foil to fall on the

burner when hot. If these residues are

allowed to cool on the ceramic surface

pitting or even cracking may occur.

Even lightweight objects may cause

damage.

Pot and pan handles should be

turned inward and not extend over the

countertop to reduce the risk of burns,

ignition of flammable materials, and

spills.

Any spills should be removed as

quickly as possible to prevent them

from burning on and becoming difficult

to remove.

Do not use pots or pans with

SAVE THESE INSTRUCTIONS

AND REVIEW THEM

PERIODICALLY

pronounced edges or ridges on the

ceramic combiset. These could scratch

the combiset permanently. See

"Cookware" for more information. Grains

of salt and sand can cause scratches.

Make sure that the bases of any pots

and pans are clean, free of any fat or

oils, and are dry.

To prevent burns and breathing

difficulty, allow the combiset to cool

before cleaning. Some cleaners may

produce toxic fumes if applied to a hot

surface.

Keep the combiset clean. Salt,

sugar, and grit can cause scratches.

When wiping spills on a hot

combiset with a wet sponge or cloth, be

careful to avoid steam burns.

Do not let flammable materials,

i.e. cooking grease, accumulate on the

appliance.

Do not use a steam cleaner to clean

this appliance. Steam could penetrate

electrical components and cause a

short circuit.

Guide to the combiset

aBurner with booster

bDisplay

Indicators

cIndicators

dControl knob

lOn/Off indicator

mBooster indicator

n"Residual Heat" indicator

Guide to the combiset

Display

= No pan on burner or pan is unsuitable

= Auto-heat

= Fault (see "Frequently asked questions")

C / 0 = Safety cut-out feature (see "Safety features")

= Booster activated

= Overheating protection (see "Safety features")

= Child safety lock (see "Safety features")

Burner data

CS 1221

Rating in watts 240 V**

Minimum to maximum

diameter*

7" - 11 3/4"

normal:

with Booster:

2,400

3,700

(18 cm - 30 cm)

* Pots with a bottom diameter in the stated range may be used.

** The stated power may vary depending on the size and material of the

cookware.

Before using for the first time

Clean the combiset

Heat the appliance

^ Before using for the first time, clean

the appliance with a damp cloth and

dry with a soft cloth.

When the combiset is first connected to

the power supply and after a power

failure, all indicators in the display will

light up for approx. 1 second. The

combiset can be used as normal once

the indicators go out.

Do not use liquid dish soap to clean

the combiset, this may cause

permanent blue discolorations.

Metal components of the appliance

have a protective coating which may

give off a slight odor the first time

the appliance is heated.

The smell will dissipate after a short

time and does not indicate a faulty

connection or appliance defect.

Induction

How it works

If no pan or an unsuitable pan is placed

on the burner, the burner and the

combiset will switch off automatically

after 3 minutes. 0 will flash alternately

with C in the display.

An induction coil is located under the

burner. When the burner is switched

on, this coil creates a magnetic field

which impacts directly on the base of

the pan and heats it up. The burner

itself is heated indirectly by the heat

given off by the pan.

To use the burner again as normal, first

turn the control knob to "0".

Induction burners only work when a

magnetic based pan is placed on it

(see "Cookware").

Be careful not to place cutlery or

other metal objects on the combiset.

When the appliance is switched on,

or when there is residual heat

present, there is the risk of metal

objects heating up quickly.

Induction automatically recognizes the

size of the pan, i.e. heat is only

generated in the area covered by the

base of the pan.

Beware of burns.

The burner will not work:

Depending on the material, other

objects left on the combiset could

also melt or catch fire.

– if it is switched on without a pan in

place, or if the pan is unsuitable

(non-magnetic base).

Turn off the burner after use.

– if the diameter of the pan is too small.

– if the pan is taken off the burner

when it is turned on.

If this happens, ß will flash in the

display.

If a suitable pan is placed on the burner

within 3 minutes, ß will go out and you

can continue cooking as normal.

Induction

Noises

The appliance has a cooling fan to help

extend the life of the electronics. When

the combiset is being used at high

levels for a long period of time, this will

come on and you will hear a whirring

sound. The fan may continue to run

after the appliance has been switched

off.

When using an induction burner, the

following noises can occur in the pan,

depending on what it is made of and

how it is constructed.

– Higher power settings may cause a

buzz. This will decrease or cease

altogether when the power setting is

reduced.

– If the pan base is made of layers of

different materials (e.g. a

sandwiched base), a cracking sound

may be heard.

– You may hear a clicking sound from

the electronic switches, especially on

lower settings.

Induction

Cookware

Pan size

Suitable pans include:

To make optimum use of the burner,

choose cookware that fits between the

inner and outer marking of the burner. If

the base diameter of the pan is smaller

than the inner marking, the induction

heating will not work. The burner will

behave as if it has no pan on it.

– stainless steel pans with a magnetic

base

– enameled steel pans

– cast iron pans

Unsuitable pans:

– stainless steel pans without a

magnetic base

– aluminum and copper pans

– glass, ceramic or earthenware pots

and pans

To test whether a pot or pan is suitable

for use on an induction combiset, hold

a magnet to the base of the pan. If the

magnet sticks, the pan is suitable.

Unless the pan manufacturer states

that you can do so, do not use pans

with very thin bases on this

combiset, and never heat empty

pans. This could damage the

appliance and cookware, and effect

the uniformity of the cooking.

Use

Turning the burner On/Off

Residual heat indicator

^ To turn the burner on, press the

control knob down and turn it

The residual heat indicator will go out

once the combiset has cooled to a safe

temperature.

clockwise a to the desired setting.

As long as the residual heat

indicator is lit do not touch or place

any heat sensitive items on the

burner. Danger of burns, and fire

hazard.

^ To turn the burner off, turn the

control knob counterclockwise b to

"0".

Do not turn the burner on without

pressing the control knob down, and

do not turn the knob past "B I" to

reach "0".

When the combiset is turned on the

On/Off indicator lights up. Once the

combiset has reached a factory set

temperature the residual heat indicator

will light.

When the combiset is turned off the

On/Off indicator will go out.

Use

Settings

Use for

Power level*

Melting butter, chocolate, etc.

Dissolving gelatin

1 - 2

Prepare yogurt

Warming small quantities of food or liquid

Keeping delicate dishes warm

Cooking rice,

1 - 3

Thawing frozen vegetables

Warming liquid or half-set foods

Thickening sauces, e.g., hollandaise sauce

Cooking rice pudding

2 - 4

3 - 5

Defrosting frozen foods

Steaming vegetables, fish, etc.

Cooking pasta, soups, etc.

Steaming grains

Boiling and continued cooking of large quantities of food

5 - 6

Gently sautéing fish, cutlets, sausages, fried eggs, etc.

(without smoking the oil/fat)

Frying pancakes, crepes, etc.

7 - 8

Boiling large quantities of water

Parboiling

Keep warm

(

* These settings are intended as guidelines only. When cooking with large pots,

large quantities of food/liquid or without using a lid, a higher setting is needed.

For smaller quantities select a lower setting.

Use

Auto-heat

Activating Auto-heat

When Auto-heat has been activated,

the burner switches on automatically at

the highest setting and then switches to

the continued power level which was

selected. The "heat-up" time depends

on which continued power level has

been chosen (see table).

^ Turn the control knob

counterclockwise as far as it will go

and hold until an A appears in the

display.

If the knob is held too long, an L will

appear in the display and the Lock

is activated (see "Child safety lock").

Continued

Heat-up time

(approx.)

power level*

^ Turn the control knob clockwise to

min : sec

the desired continued power level.

0 : 15

0 : 25

0 : 50

2 : 00

5 : 50

2 : 50

If a continued power level is not

selected within 5 seconds, the

Auto-heat feature is not activated.

Once Auto-heat has been activated the

continued power level must be set

within 10 seconds. After this time the

level cannot be changed.

Changing the continued power level

after 10 seconds will deactivate the

Auto-heat function.

During the Auto-heat phase an A will

show in the display.

The higher continued cooking settings

are generally used for frying, a short

heat-up time is needed to heat up the

pan initially.

Taking a pan off the burner while

Auto-heat is in operation interrupts the

function. It will resume if a pan is

placed back on the burner within

3 minutes.

Use

Booster function

To activate the Booster

The burner is equipped with a booster

function to temporarily increase the

power level. This boost is intended to

quickly bring large quantities of water

to the boil, e.g. cooking pasta. When

the Booster is activated the burner will

operate with extra power for 10

minutes.

^ Turn the control knob past power

level 9 to BI, then turn back to level 9.

I appears in the display and the B

indicator lights up.

To deactivate the Booster function

The booster function can be turned off

early if desired.

Once the booster time has elapsed the

burner will automatically revert to power ^ Turn the control knob past power

level 9. The B indicator and I in the

level 9 to BI and then back to 9; or

simply reduce the power level.

display will go out.

Taking a pan off the burner while the

booster is in operation interrupts the

booster function. It will resume if a pan

is placed back on the burner within 3

minutes.

Use

Keep warm

Tips

This function can be used for keeping

food warm right after it has been

cooked. It is not for reheating food

which has already cooled.

– Cover the pan with a lid.

– It is not necessary to stir the food

while it is being kept warm.

– Nutrients are lost when food is

cooked, therefore try to keep the

warming time to a minimum.

Once activated the keep warm function

will switch off automatically after 2

hours.

Safety features

Child Safety Lock

Safety cut-out

The combiset has a safety cut-out

feature in case it is not turned off after

use.

Keep children away from the

combiset for their own safety.

The combiset has a Child Safety Lock

to prevent children from turning on the

burner.

If the burner is heated for an unusually

long period of time (see table), and the

power level settings are not adjusted,

the combiset will turn itself off

To activate the Child Safety Lock:

automatically and the residual heat

indicator will light.

^ Turn the control knob

counterclockwise as far as it will go,

and hold until L appears in the

display.

C and 0 will flash alternately in the

display.

^ To use the combiset again, first turn

the control knob to "0".

If the control knob is touched after the

lock is activated an L will appear in the

display for 3 seconds.

The On/Off indicator and the display

will go out.

To deactivate the Child Safety Lock:

Power level

Maximum

^ Turn the control knob

operating hours

counterclockwise as far as it will go,

and hold until the L goes out and 0

appears briefly in the display.

Safety features

Overheating protection

Once the burner has cooled to a safe

temperature the combiset can be used

again as normal.

The induction coils and the cooling

element of the electronics are fitted with

an overheating protection feature. This

prevents the induction coils and cooling

element from overheating.

The overheating protection feature may

be activated by:

This mechanism works in the following

ways:

– heating an empty pan,

– oils or fats being heated on the

highest power level,

– If the booster function is being used,

it will be switched off.

– the underside of the appliance is not

sufficiently ventilated.

– The power level will be reduced.

– If an induction coil is affected, the

burner will turn off and an H will

appear in the display.

If the overheating protection feature

activates again, contact Miele

Technical Service.

^ Turn the control knob to "0".

Once the H has gone out, the combiset

can be used again as normal.

If the control knob is not turned back to

"0", C and 0 will flash in the display. To

use the burner again, first turn the

control knob to "0".

– If the cooling element is affected, the

power supply to the burner will be

reduced.

Once the cooling element has cooled

sufficiently the burner will continue

working again at the original power

level.

– If the temperature continues to rise

after the power level has been

reduced, the burner will switch off.

C and 0 will flash alternately in the

display.

^ Turn the control knob to "0".

Cleaning and care

Do not use a steam cleaner to clean

this appliance. Steam could

Clean any spills immediately before

they become difficult to remove.

penetrate electrical components and

cause a short circuit. Pressurized

steam could cause permanent

damage to the surface.

Clean the appliance regularly,

preferably after each use. Allow the

appliance to cool before cleaning.

Do not use any sharp pointed

objects which could damage the

seal between the ceramic surface,

the surrounding frame and the

countertop.

Ceramic surfaces

^ Wipe off any soiling using a damp

cloth. Stubborn soiling is best

removed with a shielded scraper

blade.

Never use abrasive cleaners,

caustic (oven) cleaners, dishwasher

detergent, scouring pads, steel wool

or hard brushes. They will damage

the surface.

^ Apply a ceramic cleaner (available

from Miele) using a soft cloth or

paper towel.

^ To remove any limescale deposits or

metallic residue apply a ceramic

cleaner using a soft cloth or use a

shielded scraper blade if necessary.

The ceramic surface can be cleaned

using a cleaner for ceramic

surfaces. Follow the manufacturer’s

instructions.

^ After cleaning wipe the ceramic

surface with a damp cloth and dry.

A cleaner with a special additive to

prevent water marks and smears on the

ceramic surface may be used.

Make sure that no cleaner residue

remains on the ceramic surface by

carefully wiping the combiset with a

damp cloth. They may damage the

combiset or produce toxic fumes

when heated.

Any melted solids like sugar, plastic or

aluminum foil should be removed as

quickly as possible, while the burner is

still warm. If they are allowed to harden

the combiset may become pitted.

Be sure that pot and pan bases are

clean and dry.

^ Turn the burner off.

^ Using a shielded scraper blade,

scrape the melted item immediately

off the burner while it is still hot.

Use caution: Danger of burns!

After cleaning dry the ceramic

surface with a soft cloth to prevent a

build up of limescale deposits.

^ Allow the combiset to cool and clean

as previously described.

Cleaning and care

Stainless steel

Clean stainless steel surfaces with

warm water and liquid dish soap

applied with a non-abrasive sponge

and then wipe dry with a soft cloth.

Soak baked or hardened spills first to

loosen them.

Stainless steel surfaces can be cleaned

using a non-abrasive stainless steel

cleaner (available from Miele).

To help prevent resoiling, a conditioner

for stainless steel can also be used.

Apply sparingly with even pressure.

Do not use stainless steel cleaner on

or around the printing, it may rub

off. Use only a soft sponge with a

mild solution of warm water and

liquid dish soap to clean this area.

Frequently asked questions

,^{Repairs should only be carried out by an authorized technician in}

accordance with local and national safety regulations. Unauthorized repairs

could cause injury or appliance damage.

What if the burner does not heat up after it is turned on?

Possible fault

Solution

The Child safety lock is activated. See "Child safety lock".

The Overheating protection feature See "Overheating protection".

has activated.

The main fuse has blown.

Check the main fuse.

Replace the fuse or "trip" the circuit breaker.

The demo-mode is activated.

To de-activate, turn the control knob briefly

When demo mode is activated, d (approx. 1 sec) to the left, two times, all the

will appear in the display for a few way to the stop, then turn it a third time and

seconds after turning the hold for approx. 3 seconds.

appliance on.

If none of the above is the case, turn the control knob to "0", and disconnect the

appliance from the electrical supply for 1 minute.

Reconnect the power and turn the appliance on. If it still does not heat, contact

Miele Technical Service.

What if ß appears in the display?

Possible fault

Solution

The burner is turned on but no

cookware is placed on it.

Turn the burner off and place suitable

cookware on it.

The pan being used is not suitable See "Cookware" for information on type and

for the combiset or is not the right size of suitable cookware.

size.

What if an F appears in the display?

Possible fault

Solution

The temperature sensor for the

burner is faulty.

Do not use the combiset until it has been

repaired. Contact Miele Technical Service.

Frequently asked questions

What if the combiset turns itself off automatically?

Possible fault

Solution

Either the "Safety cut-out" feature or the See "Overheating protection" or "Safety

"Overheating protection" feature has cut-out".

been activated.

What if one of the following errors occurs:

- The booster function turns off automatically ahead of time.

- C and 0 flash alternately in the display.

- H is shown in the display.

Possible fault

Solution

The overheating protection feature has See "Overheating protection".

been activated.

The food does not cook when using the Auto-heat function.

Possible fault

Solution

Large amounts of food are being

cooked.

Select a higher continued power level

or begin cooking at the highest level

and turn the power back by hand.

The pot or pan does not transfer the

heat properly.

Use the correct pots and pans, see

"Cookware".

The cooling fan continues to run after the combiset is turned off.

Possible fault

Solution

This is not a fault.

The fan continues to run until the

appliance has cooled sufficiently. It will

turn off automatically.

Technical Service

In the event of a fault which you cannot

easily fix yourself, please contact the

Miele Technical Service Department at

the address on the back of this booklet.

When contacting Technical Service

please quote the serial number and

model of the appliance.

Adhere rating label sticker supplied

with the appliance below.

Technical Service

MieleCare

(USA only)

MieleCare, our Extended Service

Contract program; gives you the

assurance of knowing that your

appliance investment is covered by 5

years of worry free ownership.

MieleCare is the only Extended Service

Contract in the industry that guarantees

repairs by a Miele Authorized Service

Provider using genuine Miele parts.

Only genuine Miele parts installed by

factory trained professionals can

guarantee the safety, reliability and

longevity of your Miele appliance.

Please note that unless expressly

approved in writing by the Miele

Service department, Extended Service

Contracts offered by other providers for

Miele products will not be recognized

by Miele. Our goal is to prevent

unauthorized (and untrained) service

personnel from working on your Miele

products, possibly doing further

damage to them, you and/or your

home.

To learn more about MieleCare

Extended Service Contracts, please

contact your appliance dealer or visit

us online at:

http://miele.com/mielecare

Installation Instructions

IMPORTANT: SAVE FOR THE LOCAL ELECTRICAL INSPECTOR'S USE

To prevent accidents

and appliance damage

read these instructions

before

installation or use.

IMPORTANT INSTALLATION SAFETY INSTRUCTIONS

Note to the installer:

This appliance has not been

Please leave this instruction book

with the consumer for the local

electrical inspector’s use.

designed for maritime use or for use in

mobile installations such as recreational

vehicles or aircraft. However, under

certain conditions it may be possible for

installation in these applications. Please

contact the Miele Technical Service

Department with specific requirements.

The minimum distances given in

these Installation Instructions must

be observed in order to ensure safe

operation. Failure to do so increases

the risk of fire.

You must ensure the power cord for

the appliance will not be subject to any

mechanical strain after installation.

The cabinetry and venting hood

should be installed first to prevent

damage to the appliance.

If a protective base is installed

beneath the appliance, a minimum

distance of 1 ⁹/₁₆" (40 mm) between the

top of the protective base and the

bottom of the appliance must be

maintained.

The countertop must be bonded

with heat resistant (212°F/100°C)

adhesive to prevent distortion or

dissolving.

The appliance must not be

Any back splashes must be

heat-resistant as well.

permanently sealed into the countertop

when installed. The sealing strip under

the edge of the appliance provides a

sufficient seal for the countertop. See

"Sealing".

The appliance must not be installed

over a dishwasher, washer, dryer,

refrigerator or freezer. Heat radiated by

the appliance may damage them.

Keep this instruction book in a safe

place for reference and pass it on to

any future user.

To eliminate the risk of burns or fire

by reaching over heated surfaces

cabinet storage space above the

appliance should be avoided. If cabinet

storage is necessary, the risk can be

reduced by installing a venting hood to

project horizontally a minimum of 5"

(127 mm) beyond the bottom of the

cabinets.

IMPORTANT INSTALLATION SAFETY INSTRUCTIONS

Safety distances above the

appliance

The minimum safety distance given by

the hood manufacturer must be

maintained between the combiset and

the hood above it. See the installation

instructions of the hood for these safety

measurements.

If the hood manufacturers instructions

are not available or if flammable objects

are installed over the combiset (e.g.

cabinets, utensil rail, etc.), a minimum

safety distance of 30" (760 mm) must

be maintained.

If there is more than one appliance

beneath a hood (e.g. wok burner

and electric combiset), and they

have different minimum safety

distances always observe the

greater distance.

IMPORTANT INSTALLATION SAFETY INSTRUCTIONS

Safety distances to the sides

of the appliance

The appliance should only be installed

(50 mm)

2 "

as shown in the illustrations, while

maintaining the required safety

distances shown. Do not install the

appliance between two tall cabinets,

this is a fire hazard.

A distance of at least 2" (50 mm) must

be kept between the countertop cut-out

and the rear wall because of the high

temperatures radiated.

recommended

The minimum distance required from

the countertop cut-out to the side wall

(50mm)

2" (50 mm)

for CS 1112

CS 1122

CS 1212

CS 1221

CS 1223

CS 1326

CS 1411

not recommended

6" (150 mm) for CS 1312

CS 1322

CS 1421

10" (250 mm) for CS 1011

CS 1012

CS 1028

not permitted

Installation

Safety distance from the wall covering

If a wall covering is installed, a minimum safety distance must be maintained

between the countertop cut-out and the covering, since high temperatures can

damage these materials.

If the covering is made of a combustible material (such as wood), the distance

between the countertop cut-out and the wall covering must be a minimum of

2" (50 mm).

For coverings made of non-combustible materials (such as metal, marble, granite

or ceramic tiles) the minimum safety distance e between the countertop cut-out

and the wall covering must be 2" (50 mm) minus the thickness of the covering.

For example: thickness of wall covering 9/16" (15 mm)

2" (50 mm) - 9/16" (15 mm) = minimum safety distance 1 3/8" (35 mm).

aWall frame

bWall covering

x = thickness of the wall covering

cCountertop

dCountertop cut-out

eMinimum safety distance

with flammable materials 2" (50 mm)

with non-flammable materials 2" (50 mm) minus x

Installation

Installation dimensions

aSpring clips

bAppliance front

cInstallation height

dPower supply box with connection cable

eRating label

Installation

Cut out

If during installation the seal around

the frame does not sit flush with the

countertop in the corners, the corner

radius, maximum ³/₁₆" (4 mm), can

be carefully filed down to fit.

^ Make the countertop cut-out for the

desired number of appliances.

Remember to maintain a minimum

safety distance from the back wall,

as well as from any tall unit or side

wall to the left or right of the

combiset.