|
USER’S GUIDE
15” LCD MONITOR
1
and unused for long periods of time, unplug it from the system unit. This will
prevent damage to the monitor from lightening and power surges.
Do not overload power outlet and extension cords. Overload can result in fire
or electric shock.
Never push any object into the slot in the monitor cabinet. It could touch
dangerous voltage points or short out parts resulting in a fire or electric shock.
Never spill liquid on the monitor.
If your monitor doesn’ t operate normally, in particular if any unusual sounds
or smells come from it, immediately unplug it and contact an authorized
technician.
Do not attempt to service the monitor yourself; openings or removing covers
can expose you to dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
Unplug the monitor from the system unit and refer servicing to qualified
service personnel under the following conditions:
When the power cord or plug is damaged or frayed.
If liquid has been spilled into the monitor.
If the monitor has been exposed to rain or water.
If the monitor does not operate normally and you are following the operating
instructions. Adjust only those controls covered by the operating instructions;
improper adjustment other controls may result in damage and may require
extensive work by a qualified technician to restore the monitor to normal
operation.
If the monitor has been dropped or the cabinet has been damaged.
When the video monitor exhibits a distinct change in performance.
To ensure satisfactory operation, use the monitor only with UL listed
computers which have appropriate configured receptacles marked between
100 – 240 VAC, Min. 2 A.
3
FCC Class B Radio Frequency
Interference Statement
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules; These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However there is no guarantee that interference will not
occur in a particular installation, if this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
NOTICE
Any changes or modification not expressly approved by the party responsible
for compliance could void the user’ s authority to operate the equipment.
Doc compliance notice
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus as set out in the Radio interference
Regulations of the Canadian Department of Communications.
“Le present appreil numerque n’ emet pas de bruits radioelectriques
depassant les limites applicables aux areils numeriques de class B
prescrites dans le reglement sur le brouillage radioelectrique edicte par le
ministere des Communications du Canada.”
4
1. INTRODUCTION
1.1 GENERAL INFORMATION
The monitor is a 15.0-inch intelligent LCD monitor with ultra high resolution of
up to 1024 x 768. The microprocessor-based design was implemented with
the user in mind.
We invite you, the proud new owner of this fine monitor, to read this user’ s
manual before operating, in order to get the most out of this product.
1.2 CHECK LIST
Before using this monitor, please make sure that all the items
Listed below are present in your package:
• LCD monitor • Power cable • AC/DC adaptor • Manual
• Warranty card
2 SETUP
2.1 LCD MONITOR SETUP
2.1.1 Power Cable Connection (A)
Plug the power cable into the wall outlet, the other end of the power cable
into the AC socket.
2.1.2 Signal Cable Connection (B)
Connect the VGA cable to the PC’ s system.
2.1.3 Power On
Turn on the power of both your monitor and your computer.
3. USER INTERFACE CONTROL
There are some switches, power LED and OSD menu on the LCD Monitor.
These are to provide the users an easy way to adjust video. A description of
these functions is as follows:
3.1 OSD CONTROLS
To make any adjustment:
1. Press (MENU/Enter) key to show the OSD menu.
2. Select the item in the menu that you wish to adjust by pressing left & right
5
button.
3. Press (AUTO/EXIT) key to make this item adjustable.
Adjust the item that you selected by pressing left & right button.
OSD FUNCTIONS
?? Auto Adjust: Auto geometry setting
?? Phase / Clock: Adjust the vertical position of the picture and the picture
Clock.
?? H / V Position: Adjust the horizontal and vertical position of the picture.
?? Misc: Adjust by User
?? Reset: Reset to original factory color and geometry setting.
MISC MENU
?? Information: Shows the input signal timing
?? OSD Timer: Adjust Menu appear Time.
?? Color:
1. 5500K/6500K/9300K/User color: Factory preset 5500/6500/9300
color.
2. User Red color: Adjusts gain of red color.
3. User Green color: Adjusts gain of green color.
4. User Blue color: Adjusts gain of blue color.
?? Language: Muti-Language selection.
English\Chinese \ French\ German\ Italian\ Spanish\Japan
?? Display Mode: Graphic and text of DOS mode.
Brightness Menu：
?? Brightness：Adjusts the brightness control.
?? Contrast：Adjusts the contrast control.
3.2 FRONT PANEL CONTROLS
?? Menu /Enter Button
Press this button to show OSD menu or select the item you want to
adjust.
6
?? Brightness Hot Key Function
Press left button to adjust the brightness directly.
?? Contrast Hot Key Function
Press right button to adjust the contrast directly.
?? Power Button (
Press ( ) to turn the power on or off.
?? Power LED
)
The green light of power LED indicates the power is switched on and the
power cord is properly connected.
The red light indicates it’ s in no signal applied or improper connection of
the signal cable.
3.3 RECOMMEND RESOLUTION AND MODE FOR LCD MONITOR
We recommend that user choice one of the following modes. Show as
follows:
Resolution
720x400
640x480
640x480
640x480
800x600
800x600
Frequency
31.5KHz/70Hz
31.4KHz/60Hz
37.9KHz/72Hz
37.5KHz/75Hz
35.2KHz/56.3Hz
37.9KHz/60.3Hz
Resolution
800x600
800x600
1024x768
1024x768
1024x768
Frequency
48.1KHz/72.2Hz
46.9KHz/75Hz
48.4KHz/60Hz
56.5KHz/70Hz
60KHz/75Hz
4. DISPLAY POWER MANAGEMENT
This monitor meets the power management standards as set by the Video
Electronics Standards Association (VESA) and /or the United States
Environmental Protection Agency (EPA). This feature is designed to conserve
electrical energy by reducing power consumption.
This function is active by an operating system or Windows utility program
which turns off the monitor display and also turns off or changes the color of
the monitor’ s power LED.
Power
Mode
H-SYNC V-SYNC
Video
Indicator
Consumption
ON
Stand-by
Yes
No
Yes
Yes
Active
Blanked Amber
Green
<30W
<3W
7
Suspend
OFF
Yes
No
No
No
Blanked Amber
Blanked Amber
<3W
<3W
5. TROUBLESHOOTING
Problem: No picture appears on the screen.
??
??
??
If power LED is off, check if power cable is securely
connected.
If power LED is amber in color, check if VGA cable is
properly connected.
Adjust the brightness and contrast controls.
Problem: Picture is unstable (noise, jitter etc)
??
Check the timing of your computer and see if they are
compatible with Monitor.
??
??
Press Auto button 1~2 seconds to get stable picture.
Select and enter H-phase functionto solve noise or jitter.
6. APPENDIX
TECHNICAL INFORMATION
Precautions
Only a qualified service technician should open the monitor case.
Components inside the monitor can cause serious electric shock. Do not
attempt to remove the back cover of the monitor by yourself. Contact your
monitor dealer or authorized service personnel if your monitor needs to be
repaired.
To prevent fire or shock hazard, do not expose this monitor to rain or
moisture.
Specifications
Video and Synchronization Signals:
1. Signal cable: 15-pin D-type connector
2. Video: Analog levels
3. Horizontal Sync: TTL Positive/Negative
4. Vertical Sync: TTL Positive/Negative
5. Pixel frequency: 80MHz(max)
6. Display colors: Limited by VGA card
7.Video signal input: 0.7 Vpp.
8
Environment:
1. Operating Temperature: 10°C to 40°C
2. Operating Humidity: 10% to 85%
3. Storage temperature: -20°C ~ 60°C
Weight:
Approx. 2.8kgs(NET)
9
|