E54
í
í
í
Fourth Edition (July 2006)
This publication could contain technical inaccuracies or typographical
errors. Changes are made periodically to the information herein; these
changes will be made in later editions. Lenovo may make improvements
and/or changes in the product(s) and/or program(s) at any time.
It is possible that this publication may contain reference to, or
information about, Lenovo products (machines and programs),
programming, or services that are not announced in your country.
Requests for copies of this publication and for technical information
about Lenovo products should be made to your Lenovo Authorized
Dealer or Lenovo Retailer.
No part of this publication may be reproduced or distributed in any
form or by any means without prior permission in writing from Lenovo.
© Copyright lenovo 2006,2005; portion(c) IBM corp,2004.
All rights reserved.
Note to U.S. Government Users -- Documentation related to restricted
rights -- Use, duplication or disclosure is subject to restrictions set forth
in GSA ADP Schedule Contract with Lenovo Corp.
1
Notices
Lenovo may not offer the products, services, or features discussed in this document
in all countries. Consult your local Lenovo representative for information on the
products and services currently available in your area. Any reference to a Lenovo
product, program, or service is not intended to state or imply that only that Lenovo
product, program, or service may be used. Any functionally equivalent product,
program, or service that does not infringe any Lenovo intellectual property right may
be used instead. However, it is the user’s responsibility to evaluate and verify the
operation of any other product, program, or service.
Lenovo may have patents or pending patent applications covering subject matter
described in this document. The furnishing of this document does not give you any
license to these patents. You can send license inquiries, in writing, to:
Lenovo (United States), Inc.
500 Park Offices Drive, Hwy. 54
Research Triangle Park, NC 27709
U.S.A.
Attention: Lenovo Director of Licensing
Lenovo GROUP LTD. PROVIDES THIS PUBLICATION “AS IS” WITHOUT
WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some
jurisdictions do not allow disclaimer of express or implied warranties in certain
transactions, therefore, this statement may not apply to you.
This information could include technical inaccuracies or typographical errors.
Changes are periodically made to the information herein; these changes will be
incorporated in new editions of the publication. Lenovo may make improvements
and/or changes in the product(s) and/or the program(s) described in this publication
at any time without notice.
The products described in this document are not intended for use in implantation or
other life support applications where malfunction may result in injury or death to
persons. The information contained in this document does not affect or change
Lenovo product specifications or warranties. Nothing in this document shall operate
as an express or implied license or indemnity under the intellectual property rights of
Lenovo or third parties. All information contained in this document was obtained in
specific environments and is presented as an illustration. The result obtained in other
operating environments may vary.
Lenovo may use or distribute any of the information you supply in any way it believes
appropriate without incurring any obligation to you.
Any references in this publication to non-Lenovo Web sites are provided for
convenience only and do not in any manner serve as an endorsement of those Web
sites. The materials at those Web sites are not part of the materials for this Lenovo
product, and use of those Web sites is at your own risk.
2
Any performance data contained herein was determined in a controlled environment.
Therefore, the result obtained in other operating environments may vary significantly.
Some measurements may have been made on development-level systems and there
is no guarantee that these measurements will be the same on generally available
systems. Furthermore, some measurements may have been estimated through
extrapolation. Actual results may vary. Users of this document should verify the
applicable data for their specific environment.
Trademarks
The following terms are trademarks of Lenovo in the United States,
other countries,or both:
Lenovo
Microsoft Windows and Windows NT are trademarks of Microsoft Corporation in the
United States, other countries, or both.
Other company, product, and service names may be trademarks or service marks of others.
3
Further Help
If you are unable to correct the problem yourself, you may seek further help
as follows:
Call the Customer Support Center.
In the US call 1-800-426-7378
In Canada (Toronto Only) call 416-383-3344
In Canada (all others) call 1-800-565-3344
If possible, stay by your
computer. Your Technical
Support Representative may wish
to go through the problem with
you during the call.
In other countries contact your dealer, retailer, or other Lenovo authorized
Servicer.
Before calling, please have available as much of the following information as
possible:
1. Model and serial number from the label on your monitor.
2. Purchase receipt.
3. Description of problem.
4. Computer type and model.
5. System configuration (hardware fitted, etc.).
6. System BIOS version number.
7. Operating System and version number.
8. Display driver version number.
9. Video Adapter Type.
4
Contents
5
6
Packing list-----------------------------------------------------
Precautions ---------------------------------------------------
7
7
8
8
Installation Instructions -------------------------------------
Swivel Base ---------------------------------------------------
Power cord -----------------------------------------------------
Video cable ----------------------------------------------------
9
Operating Instructions ------------------------------------
Gen eral In struction s -------------------------------------------
Fr ont panel control --------------------------------------------
How to adjust a setting -------------------------------------------
Ad justin g th e p icture ------------------------------------------
9
10
10
11
12
12
13
Features ---------------------------------------------------------
Green m on itor --------------------------------------------------
Plug and play ----------------------------------------------------
14
Technical Support (FAQ) -----------------------------------
15-16
Appendix A – Specifications --------------------------------
17
Appendix B – Factory Preset Timing Table ------------
Installing the Device Drive.r ---------------------------------
18
Installing the Device Driver for Windows 95 or Windows 98 -------- 18
Installing the Device Driver for Windows 2000 or Windows Me ------ 19
Installing the device driver in Windows XP ------------------------- 20
Installing the device driver in Windows Vista ------------------------------------ 21
PACKING LIST
The product package should include the following items:
1. Monitor
2. Quick set up guide
3. Power cord
4. Swivel base
5. CD manual
6.
Monitor Safety,Troubleshooting, and Warranty Guide
5
PRECAUTIONS
Workplace preparation
Positioning the monitor
Choose a suitable place to position the monitor where it is not near
fluorescent desk lighting or any equipment that produces magnetic fields that
could cause interference. Ensure that the furniture or equipment can support
the weight of the monitor. Allow at least 2 in. (50 mm) ventilation space
around the monitor.
Height
The monitor should be positioned so that the top of the screen is slightly
below your eye level when you sit at your workstation.
Orientation
Choose a position that gives the least reflection from lights and windows,
usually at a right angle to any windows. Position the monitor directly in front
of you so that you do not have to twist your body. Tilt the monitor to a
comfortable viewing angle.
Work Practices
Caring for your Monitor
Be sure to disconnect the power cord from your monitor before you perform any maintenance
on the monitor. Clean your monitor as follows:
• Gently wipe the covers and the screen with a soft cloth, do not use solvents
or abrasives.
• Never drop water or other liquid into your monitor.
• Remove finger marks and grease with a damp cloth and mild detergent.
• Never use flammable cleaning materials to clean your Lenovo monitor or any
other electrical apparatus.
• Do not rub, touch, or tap the surface of the screen with sharp or abrasive
items such as a ballpoint pen or screwdriver. This type of contact may
result in a scratched picture tube.
• Do not use any type of cleaner containing an anti-static solution or similar
additive as this may scratch the screen's coating.
• Never apply detergent or other liquid directly to the screen. Dampen the
cloth and then wipe.
6
Rest
Take regular breaks. Vary your posture, and stand up and stretch
occasionally, as prolonged use of computer workstations can be tiring.
Back
Sit back in the chair and use the back rest.
Hands
Use a light touch on the keyboard, keeping your hands and fingers relaxed.
Allow a space in front of the keyboard to rest your wrists when not typing.
Consider using a wristpad.
Eyesight
Working with monitors, in common with any prolonged close work, can be
visually demanding. Look away from the screen periodically and have your
eyesight checked regularly.
Screen settings
Set the screen brightness and contrast to a comfortable level. You might have
to adjust this as the lighting changes during the day. Many application
programs let you select color combinations which can help you to view in
comfort.
INSTALLATION INSTRUCTIONS
Swivel Base
To attach the swivel base to the monitor, do the following:
•
•
•
Carefully turn the monitor on its side or upside down. (see figure 1)
Locate the cavities at the bottom front of the monitor.
Insert the pegs on the swivel base into these cavities. Push the swivel base
forward until the swivel base locks in place.
• To remove the swivel base, hold the bottom of the swivel base, and then
push it out.
Figure 1 Installing and removing the Swivel Base
7
Power Source:
1. Make sure the power cord is the correct type that is required in your area.
2. This monitor has a universal power supply that allows operation in
100/120V ac or 220/240V ac voltage (No user adjustment is required)
3. Connect the power cord into your monitor’s power input socket, and then
plug the other end into a 3-pin ac power outlet. The power cord can be
connected to either a wall power outlet or the power outlet socket on your
computer, depending on the type of power cord supplied with your
monitor.
Power cord:
For safe operation, use the power cord supplied with the unit.
Video cable
Connecting the video cable: The monitor comes with a built-in video cable.
Plug the signal cable's 15-pin connector into the computer's video port and
tighten the two screws on the cable connector. (see figure 2)
Connecting the power cord: Plug the power cord into the monitor's ac
power socket. Then plug the power cord into a grounded ac outlet or UL-
approved power strip or the power output socket on your computer.
Caution: If the AC outlet is not grounded(only two holes), install the proper
grounding adapter (not supplied).
2
1
Figure 2 Connecting cables
1.
Power Cord
2.
Signal Cable
8
OPERATING INSTRUCTIONS
General Instructions
The power switch is located at front panel of the monitor. Press the power
switch to turn the monitor on or off. The other control knobs are located at
the base of the monitor (See Figure 3). By changing these settings, the picture
can be adjusted to your personal preferences.
•
•
•
The power cord must be connected.
Connect the video cable from the monitor to the video card.
To turn the monitor on, press the POWER switch to ON position. The
power indicator will light up.
•
Your monitor features a unique quick switch system which provides a
picture within seconds after the monitor is switched on.
1
2
3
4
5
6
Figure 3
EXTERNAL CONTROLS
External Control Knob
1.
2.
3.
EXIT Key
BRIGHTNESS/
CONTRAST/
4.
5.
6.
MENU
Power Indicator
Power Switch
9
Notes
•
Do not install the monitor in a location near heat sources such as radiators
or air ducts , or in a place subject to direct sunlight , or excessive dust or
mechanical vibration or shock.
•
•
•
Save the original shipping carton and packing materials, as they will come
in handy if you ever have to ship your monitor.
For maximum protection, repackage your monitor as it was originally
packed at the factory.
To keep the monitor looking new, periodically clean it with a soft cloth.
Stubborn stains can be removed with a cloth lightly dampened with a mild
detergent solution. Never use strong solvents such as thinner, benzene, or
abrasive cleaners, since these will damage the cabinet. As a safety
precaution, always unplug the monitor before cleaning it.
Front Panel Control
•
•
Power : Press this knob to switch ON/OFF of monitor’s power.
MENU : Active OSD menu or function adjust confirm.
•
Contrast
/
: Adjust contrast or function adjust.
•
•
Brightness
/
: Adjust brightness or function adjust.
EXIT : Exit a function or inactive OSD menu.Press and
hold the "Exit" button for 10 seconds to disable/enable the
DDC/CI function.The words "DDC/CI function disable/enable
will be showed on the screen.
• Power Indicator :
Green
—
Power On mode.
Orange — Sleep or Off mode.
How to adjust a setting
The monitor controls are accessed by pressing button MENU to enable OSD
(On-Screen-Display). The main menu will be displayed as follows.
Figure 4 The OSD Message
Note: If adjustment or selection of any OSD menu is not made for more than
10 seconds, the current setup will be saved and the OSD will disappear
automatically.
10
ADJUSTING THE PICTURE
The description for function control ICONS
1.
2.
CONTRAST
Adjust the picture contrast.
Adjust the picture brightness.
BRIGHTNESS
3.
4.
5.
H- CENTER
H- SIZE
Adjust the horizontal position of the picture.
Adjust the picture’s horizontal size.
V- CENTER
Adjust the vertical position of the picture.
6.
7.
V- SIZE
ZOOM
Adjust the picture’s vertical size.
Adjust the picture’s horizontal and vertical size
simultaneously.
8.
9.
PINCUSHION
TRAPEZOID
Adjust the pincushion and barrel
Adjust the picture’s trapezoid distortion.
10.
11.
PIN-BALANCE
Adjust to compensate the pincushion unbalance.
Adjust the picture to be a rectangle.
PARALLELOGRAM
12.
ROTATION
Adjust the picture tilt to horizontal position.
The color temperature for 6500°K is x=0.313,
y=0.329 and 9300°K is x=0.283, y=0.297,
SRGB is x=0.313,y=0.329,It presents three
different color sets on the screen. You can
select 9300°K or 6500°K or SRGB by pressing
6500°K/9300°K/SRGB
(COLOR
TEMPERATURE )
13.
Brightness and contrast can't be
the MENU.
adjusted in SRGB mode.
If the 9300°K normal white or 6500°K warmer
white do not satisfy your desire, properly adjust R
. B GAIN controls to obtain your optimum
whiteness level.
14.
USER COLOR
( Red / Blue )
If color impurity occurs when moving
swiveling the monitor, press the MENU and
degauss to fix the picture condition.
or
15.
16.
DEGAUSS
MOIRE REDUCE
Moire is the result of interference between the
phosphor layout and the video signal. In some
cases, you may find the moire very noticeable.
Press the MENU to enter in the moire reduce
setting. Please adjust the level to the optimum
condition. Note: Too high of a setting will cause
the picture to shake.
17.
18.
RECALL
EXIT
Press RECALL to restore the monitor to factory
settings.
Close OSD window.
19.
SELECT LANGUAGE Select the language you like.
20.
OSD display time
Select the OSD display time: 5s,10s,or 15s.
11
FEATURES
Green monitor
•
The monitor has a power saving function .This feature will switch off
your monitor to conserve energy,after a user-specified period of inactivity.
The power-saving mode is indicated by the light-emitting diode (LED) on
the front panel:
Signal
Power
Mode
On*
Cable H-Sync V-Sync Video Indicator Consumption
Attached Yes
Yes
No
No
Active Green
Blank Orange
Blank Orange
≤ 75 W
≤
≤
Sleep
Attached
Attached
No
No
4 W
2 W
Power Off
* 1. Power consumption at on mode is measured at 1024X768@75Hz
12
THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF
THERE IS NO VIDEO INPUT SIGNAL. IN ORDER FOR THIS
MONITOR TO OPERATE PROPERLY, THERE MUST BE A VIDEO
INPUT SIGNAL.
This feature is designed to conserve electrical energy by reducing power
consumption when there is no video input signal present.when there is no
video input signal present.When there is no video input signal, this monitor,
following a time-out period,will automatically switch to an OFF mode. And the
LED will turn orange. This reduces the monitor's internal power supply
consumption. After the video input signal is restored, full power is restored
and the display is automatically redrawn. The appearance is similar to a
"Screen Saver" feature except the display is completely off. The display is
restored by pressing a key on the keyboard, or clicking the mouse.
Plug and play
Plug & Play DDC2B Feature
This monitor is equipped with VESA DDC2B capabilities according to the
VESA DDC STANDARD. It allows the monitor to inform the host system of
its identity and, depending on the level of DDC used, communicate additional
information about its display capabilities.
The DDC2B is a bidirectional data channel based on the I2C protocol.
The host can request EDID information over the DDC2B channel.
DDC/CI
This monitor can support DDC/CI.
13
TECHNICAL SUPPORT (FAQ)
Problem & Question
Power LED is not on
Possible Solution
*Verify that the power switch is in the ON
position
*Power cord must be connected
*Verify that the computer system is Plug &
Play compatible
No Plug & Play
*Verify that the video card is Plug & Play
compatible
*Verify that the D-15 plug pin of video
cable is bent
*Make sure the monitor device drivers are
installed
No picture
*Computer power switch must be in the
ON position
*Computer video card must be snugly
seated in its slot
*The signal cable must be completely
connected to the computer
*Check the color of the power LED
indicator. If it is orange, then the monitor
and the computer system are in power-
saving mode. You need to press your
keyboard or move the mouse to
reactivate the system.
Picture is fuzzy
*Adjust the Contrast and Brightness
Controls.
Picture bounces or a wave pattern *Move electrical devices that might cause
is present in the picture electrical interference.
Monitor is stuck in “Power Saving *Make sure monitor’s video cable is
Mode”
properly connected to the computer.
*Inspect monitor’s video cable and make
sure none of the pins are bent.
*Make sure computer is operational by
hitting the CAPS LOCK key on the
keyboard while observing the CAPS
LOCK LED. The LED should either
turn ON or OFF after hitting the CAPS
LOCK key.
Missing one of the primary colors *Inspect the monitor’s video cable and
(RED, GREEN, or BLUE) make sure that none of the pins are bent.
14
APPENDIX A – SPECIFICATIONS
CRT Size
38.1 cm (15 in.), 90º deflection,
22.5 mm neck
CRT
Input
Viewable Image 35.4 cm (13.9 in.), diagonal
Size
Type
0.27 mm dot pitch.
Video
0.7 Vpp, R,G,B Analog
Separate Sync. TTL Level
H./V.- Sync.
H-Frequency
V-Frequency
Positive / Negative
30 - 69 kHz
50 - 120 Hz
Scanning
Frequency
Max. Resolution
Video dot rate
1280 x 1024
110 MHz
Factory Preset mode :
User Programmable mode :
Power Source
9
8
Universal 100 – 240 V ac,
50 Hz / 60 Hz
Operating
Humidity
Dimensions
0 to 40º C (0 to 104º F)
10% to 85% relative, non-condensing
452 mm (1.5 ft) × 425 mm (1.4 ft) ×
454 mm (1.5 ft) (W × H × D)
Carton
Monitor & Base 360 mm (1.2 ft) × 362 mm (1.2 ft) ×
387 mm (1.3 ft) (W × H × D)
Weight
Unit (net)
Carton (gross) 12.5 kg ( Gross )
Attached Mini D-sub 15 Male
11.0 kg ( Net )
Signal Cable:
360
387
(In mm)
15
Switch
• Power On/Off switch
• MENU Key
UP Key
Down Key
• Contrast/
• Brightness/
• EXIT Key
• Contrast
• Brightness
• H-Center
• H-Size
External Controls:
Functions
• V-Center
• V-Size
• Zoom
• Pincushion
• Trapezoid
• Rotation
• 6500°K
• User Color
• 9300°K
•
SRGB
• Degauss
• Moire Reduce
• Recall
• Exit
•
OSD Display Time
Plug & Play
DDC 2B
Power Consumption*
Pre-set Display Area
Regulatory
75 W
260 mm (10.2 in.) x 195 mm (7.7 in.)
TUV-S, NOM, CE, MPR II
TÜV/GS,CULus,CCC
Compliance
16
APPENDIX B – FACTORY PRESET TIMING TABLE
HORIZONTAL
FREQUENCY
VERTICAL
FREQUENCY
STANDARD
RESOLUTION
VGA
720 × 400
640 × 480
640 × 480
640 × 480
800 × 600
800 × 600
1024 × 768
1024 × 768
1280 × 1024
31.33 kHz
31.47 kHz
37.50 kHz
43.27 kHz
46.88 kHz
53.67 kHz
60.02 kHz
68.68 kHz
64.98 kHz
70 Hz
60 Hz
75 Hz
85 Hz
75 Hz
85 Hz
75 Hz
85 Hz
60 Hz
VGA
VESA/75
VESA/85
VESA/75
VESA/85
VESA/75
VESA/85
VESA/60
Connector pin assignment
1
6
5
10
11
15
15 - Pin Color Display Signal Cable
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1.
2.
3.
4.
5.
6.
7.
8.
Red
Green
Blue
NC
NC
R-Ground
G-Ground
B-Ground
9.
10.
11.
12.
13.
14.
15.
NC
Ground
NC
DDC-Serial Data
H-Sync
V-Sync / V-CLK
*
DDC-Serial Clock
For DDC
*
17
Installing the Device Driver
Installing the Device Driver for Windows 95 or Windows 98
To install the device driver in Microsoft® Windows®95 or Windows98, do the following:
Note: You must download files from the Lenovo Monitor CD to use the Plug and Play feature in
Windows 95 or Windows 98.
1. Turn off the computer and all attached devices.
2. Ensure that the monitor is connected correctly.
3. Turn on the monitor and then the system unit. Allow your computer to start the
Windows 95 or Windows 98 operating system.
Your computer’s Plug and Play code might warn you that your system
hardware has changed. This means that it has detected your new
monitor for the first time.
4. Open the Display Properties window by clicking Start, Settings,
Control Panel and then double clicking on the Display icon.
5. Click the Settings tab.
If you are using Windows 95:
6. 1. Click the Change Display Type button.
2. Click the Change Monitor Type button.
• If you are using Windows 98:
6. 1. Click the Advanced button.
2. Click the Monitor tab.
3. Open the Upgrade Device Wizard window by clicking
on Change button and then select the Next button.
4. Click “Display a list of the known drivers for this device so that
I can choose a specific driver” and then select the Next button.
7. Insert the Lenovo Monitor CD into the CD drive and click the Have Disk button.
8. Click OK.
9. Ensure that the CD drive letter is selected, and then select “DRIVERS” folder.
10. Select E54 CRT monitor and click OK. The files will be copied from
the CD to your hard disk drive.
11. Close all open windows and remove the CD.
12. Restart the computer.
The system will automatically select the maximum refresh rate and
corresponding Color Matching Profiles.
18
Installing the Device Driver for Windows 2000 or Windows Me
To install the device driver in Microsoft® Windows®2000 Professional or Microsoft Windows
Millennium Edition (Me), do the following:
Note: You must download files from the Lenovo Monitor CD to use the Plug and Play feature
in Windows 2000 or Windows Me.
1. Turn off the computer and all attached devices.
2. Ensure that the monitor is connected correctly.
3. Turn on the monitor and then the system unit. Allow your computer to start the Windows
2000 or Windows Me operating system.
4. Open the Display Properties window by clicking Start, Settings,
Control Panel and then double-clicking the Display icon.
5. Click the Settings tab.
6. Click the Advanced button.
7. Click the Monitor tab.
8. Click the Properties button.
9. Click the Driver tab.
10. Open the Upgrade Device Driver Wizard window by clicking on
Update Driver and then click the Next button.
11. Select “Display a list of the known drivers for this device so that I can
choose a specific driver” and then click the Next button.
12. Insert the Lenovo Monitor CD into the CD drive and click the Have Disk button.
13. Click OK.
14. Ensure that the CD drive letter is selected, and then select the “DRIVERS”
folder.
15. Select E54 CRT monitor and click OK. The files will be copied from
the CD to your hard disk drive.
16. Close all open windows and remove the CD.
17. Restart the computer.
The system will automatically select the maximum refresh rate and
corresponding Color Matching Profiles.
19
Installing the device driver in Windows XP
To install the device driver in Microsoft® Windows XP, do the following:
Note: You must download files from the Lenovo Monitor CD to use the Plug and Play feature
in XP.
1. Turn off the computer and all attached devices.
2. Ensure that the monitor is connected correctly.
3. Turn on the monitor and then the system unit. Allow your computer to start the Windows
XP operating system.
4. Open the Display Properties window by clicking Start, Settings,
Control Panel and then double-clicking the Display icon.
5. Click the Settings tab.
6. Click the Advanced button.
7. Click the Monitor tab.
8. Click the Properties button.
9. Click the Driver tab.
10. Open the Hardware Update Wizard window by clicking on Update Driver and then click
the Next button.
11. Select “Install from a list or Specific location (Advanced)” and then click the Next button.
12. Insert the Lenovo Monitor CD into the CD drive and click the Have Disk button.
13. Click OK.
14. Ensure that the CD drive letter is selected, and then select the “DRIVERS”
folder.
15. Select E54 monitor and click OK. The files will be copied from
the CD to your hard disk drive.
16. Close all open windows and remove the CD.
17. Restart the computer.
The system will automatically select the maximum refresh rate and
corresponding Color Matching Profiles.
20
Installing the device driver in Windows Vista
To install the device driver in Microsoft® Windows Vista, do the following:
Note: You must download files from the Lenovo Monitor CD to use the Plug and Play feature
in Windows Vista.
1. Turn off the computer and all attached devices.
2. Ensure that the monitor is connected correctly.
3. Turn on the monitor and then the system unit. Allow your computer to start the Windows
Vista operating system.
4. Open the Display Properties window by clicking Start, Control Panel
and then double-clicking the Hardware and Sound icon.
5. Click the Personalization icon.
6. Click the Display Settings icon.
7. Click the Advanced Settings button.
8. Click the Monitor tab.
9. Click the Properties button.
10. Click the Driver tab.
11. Open the "Update Driver Software-Generic PnP Monitor" window by clicking on Update Driver
and then click the "Browse my computer for driver software" button.
12. Select “Let me pick from a list of device drivers on my computer” .
13. Insert the Lenovo Monitor CD into the CD drive and click the Have Disk button.
14. Ensure that the CD drive letter is selected, and then click OK.
15. Select E54 monitor and click Next. The files will be copied from
the CD to your hard disk drive.
16. Close all open windows and remove the CD.
17. Restart the computer.
The system will automatically select the maximum refresh rate and
corresponding Color Matching Profiles.
21
Service Information
The following parts are for use by Lenovo service, or Lenovo authorized dealers,
to support the customer warranty. Parts are for service use only.
Model Type 6331(for E54)
41A1832
41A1833
41A1834
41A1835
6331
6331
6331
BCN
BCE
BCS
FRU E54 Monitor - NH, MPR-II,
FRU E54 Monitor - EQ, MPR-II,
FRU E54 Monitor - SH, MPR-II,
FRU E54 - Tilt/Swivel,
BB
BB
BB
BB
NA,AP
ASEAN,LA
ANZ
WW
Customer responsibilities
The warranty does not apply to a product which has been damaged due to accident, misuse, abuse,
improper installation, usage not in accordance with product specifications and instructions, natural
or personal disaster, or unauthorized alterations, repairs or modifications.
The following are examples of misuse or abuse and not covered by warranty:
•
Images burned onto the screen of a CRT monitor. Burned image is preventable by utilizing a
moving screen saver of power management.
•
•
Physical damage to covers, bezel, base and cables.
Scratches or punctures on monitor screens.
22
|