Hardware Maintenance Manual
Machine Types: 6393, 6394, 6395, 6396, and 6397
Hardware Maintenance Manual
Machine Types: 6393, 6394, 6395, 6396, and 6397
Note: Before using this information and the product it supports, be sure to read the information under Appendix A
Eighth Edition (September 2010)
© Copyright Lenovo 2005, 2010.
LENOVO products, data, computer software, and services have been developed exclusively at private expense and are
sold to governmental entities as commercial items as defined by 48 C.F.R. 2.101 with limited and restricted rights to
use, reproduction and disclosure.
LIMITED AND RESTRICTED RIGHTS NOTICE: If products, data, computer software, or services are delivered pursuant
a General Services Administration ″GSA″ contract, use, reproduction, or disclosure is subject to restrictions set forth
in Contract No. GS-35F-05925.
Contents
Selecting or changing the startup device
sequence .
41
41
41
1
Advanced settings .
compliant FRUs .
1
Exiting from the Setup Utility program
General safety .
3
3
5
43
43
59
60
61
62
Electrical safety .
Diagnostic error codes
Safety inspection guide .
Beep symptoms .
Handling electrostatic discharge-sensitive
devices
5
6
6
Miscellaneous error messages
Undetermined problems .
Grounding requirements .
Safety notices (multi-lingual translations)
65
65
66
66
68
68
69
70
72
73
74
75
76
77
78
79
81
The ThinkVantage Productivity Center program .
29
29
29
Additional information resources
Specifications . .
31
32
Replacing the microprocessor
Replacing the system board
Replacing a hard disk drive.
PC-Doctor for Windows PE.
33
33
Running diagnostics from the Rescue and
PC-Doctor for DOS .
33
34
34
34
Replacing the Express card assembly
Replacing the system fan assembly
Running diagnostics from the CD or
diskettes .
Navigating through the diagnostics
34
programs .
35
35
36
83
93
103
117
127
Running tests .
39
39
39
39
40
40
40
40
40
Viewing and changing settings
Using passwords.
Security features .
139
139
139
139
139
Setting, changing, and deleting a password
© Copyright Lenovo 2005, 2010
v
Updating (flashing) BIOS from a CD-ROM or
diskette
Recovering from a POST/BIOS update failure
Power management
141
139
140
140
144
144
(ACPI) BIOS .
141
vi Hardware Maintenance Manual
Chapter 1. About this manual
This manual contains service and reference information for ThinkCentre® computers listed on the cover. It is
intended only for trained servicers who are familiar with Lenovo® computer products.
This manual includes a complete Field Replaceable Unit (FRU) part number listing for each machine type
listed on the cover. If you have internet access, FRU part numbers are also available at:
http:/www.lenovo.com/support
Important Safety Information
Be sure to read all caution and danger statements in this book before performing any of the instructions.
Veuillez lire toutes les consignes de type DANGER et ATTENTION du présent document avant d'exécuter
les instructions.
Lesen Sie unbedingt alle Hinweise vom Typ "ACHTUNG" oder "VORSICHT" in dieser Dokumentation, bevor
Sie irgendwelche Vorgänge durchführen
Leggere le istruzioni introdotte da ATTENZIONE e PERICOLO presenti nel manuale prima di eseguire una
qualsiasi delle istruzioni
Certifique-se de ler todas as instruções de cuidado e perigo neste manual antes de executar qualquer
uma das instruções
Es importante que lea todas las declaraciones de precaución y de peligro de este manual antes de seguir
las instrucciones.
Important information about replacing RoHS compliant FRUs
RoHS, The Restriction of Hazardous Substances in Electrical and Electronic Equipment Directive
(2002/95/EC) is a European Union legal requirement affecting the global electronics industry. RoHS
requirements must be implemented on Lenovo products placed on the market and sold in the
European Union after June 2006. Products on the market before June 2006 are not required to
have RoHS compliant parts. If the parts are not compliant originally, replacement parts can also
be noncompliant, but in all cases, if the parts are compliant, the replacement parts must also be
compliant.
© Copyright Lenovo 2005, 2010
1
Note: RoHS and non-RoHS FRU part numbers with the same fit and function are identified with unique
FRU part numbers.
Lenovo plans to transition to RoHS compliance well before the implementation date and expects its suppliers
to be ready to support Lenovo's requirements and schedule in the EU. Products sold in 2005, will contain
some RoHS compliant FRUs. The following statement pertains to these products and any product Lenovo
produces containing RoHS compliant parts.
RoHS compliant ThinkCentre parts have unique FRU part numbers. Before or after June, 2006, failed RoHS
compliant parts must always be replaced using RoHS compliant FRUs, so only the FRUs identified as
compliant in the system HMM or direct substitutions for those FRUs can be used.
Products marketed before June 2006
Products marketed after June 2006
Replacement FRU
Replacement FRU
Must be RoHS
Current or original part
Non-RoHS
Current or original part
Can be Non-RoHS
Can be RoHS
Must be RoHS
Non-RoHS
Non-RoHS
Can sub to RoHS
Must be RoHS
RoHS
Note: A direct substitution is a part with a different FRU part number that is automatically shipped by the
distribution center at the time of order.
2
Hardware Maintenance Manual
Chapter 2. Safety information
This chapter contains the safety information that you need to be familiar with before servicing a computer.
General safety
Follow these rules to ensure general safety:
• Observe good housekeeping in the area of the machines during and after maintenance.
• When lifting any heavy object:
1. Ensure you can stand safely without slipping.
2. Distribute the weight of the object equally between your feet.
3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift.
4. Lift by standing or by pushing up with your leg muscles; this action removes the strain from the
muscles in your back. Do not attempt to lift any objects that weigh more than 16 kg (35 lb) or objects
that you think are too heavy for you.
• Do not perform any action that causes hazards to the customer, or that makes the equipment unsafe.
• Before you start the machine, ensure that other service representatives and the customer's personnel are
not in a hazardous position.
• Place removed covers and other parts in a safe place, away from all personnel, while you are servicing
the machine.
• Keep your tool case away from walk areas so that other people will not trip over it.
• Do not wear loose clothing that can be trapped in the moving parts of a machine. Ensure that your sleeves
are fastened or rolled up above your elbows. If your hair is long, fasten it.
• Insert the ends of your necktie or scarf inside clothing or fasten it with a nonconductive clip, approximately
8 centimeters (3 inches) from the end.
• Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for your clothing.
Remember: Metal objects are good electrical conductors.
• Wear safety glasses when you are: hammering, drilling soldering, cutting wire, attaching springs, using
solvents, or working in any other conditions that might be hazardous to your eyes.
• After service, reinstall all safety shields, guards, labels, and ground wires. Replace any safety device
that is worn or defective.
• Reinstall all covers correctly before returning the machine to the customer.
Electrical safety
CAUTION:
Electrical current from power, telephone, and communication cables can be hazardous. To avoid
personal injury or equipment damage, disconnect the attached power cords, telecommunication
systems, networks, and modems before you open the server/workstation covers, unless instructed
otherwise in the installation and configuration procedures.
Observe the following rules when working on electrical equipment.
© Copyright Lenovo 2005, 2010
3
Important: Use only approved tools and test equipment. Some hand tools have handles covered with a soft
material that does not insulate you when working with live electrical currents. Many customers have, near
their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges.
Do not use this type of mat to protect yourself from electrical shock.
• Find the room emergency power-off (EPO) switch, disconnecting switch, or electrical outlet. If an electrical
accident occurs, you can then operate the switch or unplug the power cord quickly.
• Do not work alone under hazardous conditions or near equipment that has hazardous voltages.
• Disconnect all power before:
– Performing a mechanical inspection
– Working near power supplies
– Removing or installing Field Replaceable Units
• Before you start to work on the machine, unplug the power cord. If you cannot unplug it, ask the customer
to power-off the wall box that supplies power to the machine and to lock the wall box in the off position.
• If you need to work on a machine that has exposed electrical circuits, observe the following precautions:
– Ensure that another person, familiar with the power-off controls, is near you.
Remember: Another person must be there to switch off the power, if necessary.
– Use only one hand when working with powered-on electrical equipment; keep the other hand in your
pocket or behind your back.
Remember: There must be a complete circuit to cause electrical shock. By observing the above rule,
you may prevent a current from passing through your body.
– When using testers, set the controls correctly and use the approved probe leads and accessories for
that tester.
– Stand on suitable rubber mats (obtained locally, if necessary) to insulate you from grounds such as
metal floor strips and machine frames.
Observe the special safety precautions when you work with very high voltages; these instructions are in
the safety sections of maintenance information. Use extreme care when measuring high voltages.
• Regularly inspect and maintain your electrical hand tools for safe operational condition.
• Do not use worn or broken tools and testers.
• Never assume that power has been disconnected from a circuit. First, check that it has been powered-off.
• Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors,
nongrounded power extension cables, power surges, and missing safety grounds.
• Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is
conductive; such touching can cause personal injury and machine damage.
• Do not service the following parts with the power on when they are removed from their normal operating
places in a machine:
– Power supply units
– Pumps
– Blowers and fans
– Motor generators
and similar units. (This practice ensures correct grounding of the units.)
• If an electrical accident occurs:
– Use caution; do not become a victim yourself.
– Switch off power.
– Send another person to get medical aid.
4
Hardware Maintenance Manual
Safety inspection guide
The intent of this inspection guide is to assist you in identifying potentially unsafe conditions on these
products. Each machine, as it was designed and built, had required safety items installed to protect users
and service personnel from injury. This guide addresses only those items. However, good judgment should
be used to identify potential safety hazards due to attachment of features or options not covered by this
inspection guide.
If any unsafe conditions are present, you must determine how serious the apparent hazard could be and
whether you can continue without first correcting the problem.
Consider these conditions and the safety hazards they present:
• Electrical hazards, especially primary power (primary voltage on the frame can cause serious or fatal
electrical shock).
• Explosive hazards, such as a damaged CRT face or bulging capacitor
• Mechanical hazards, such as loose or missing hardware
The guide consists of a series of steps presented in a checklist. Begin the checks with the power off, and
the power cord disconnected.
Checklist:
1. Check exterior covers for damage (loose, broken, or sharp edges).
2. Power-off the computer. Disconnect the power cord.
3. Check the power cord for:
a. A third-wire ground connector in good condition. Use a meter to measure third-wire ground continuity
for 0.1 ohm or less between the external ground pin and frame ground.
b. The power cord should be the appropriate type as specified in the parts listings.
c. Insulation must not be frayed or worn.
4. Open the cover.
5. Check for any obvious alterations. Use good judgment as to the safety of any alterations.
6. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or
other liquids, or signs of fire or smoke damage.
7. Check for worn, frayed, or pinched cables.
8. Check that the power-supply cover fasteners (screws or rivets) have not been removed or tampered with.
Handling electrostatic discharge-sensitive devices
Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to
electrostatic discharge (ESD). ESD damage can occur when there is a difference in charge between objects.
Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the
person handling the part are all at the same charge.
Notes:
1. Use product-specific ESD procedures when they exceed the requirements noted here.
2. Make sure that the ESD protective devices you use have been certified (ISO 9000) as fully effective.
When handling ESD-sensitive parts:
• Keep the parts in protective packages until they are inserted into the product.
• Avoid contact with other people while handling the part.
Chapter 2. Safety information
5
• Wear a grounded wrist strap against your skin to eliminate static on your body.
• Prevent the part from touching your clothing. Most clothing is insulative and retains a charge even when
you are wearing a wrist strap.
• Use the black side of a grounded work mat to provide a static-free work surface. The mat is especially
useful when handling ESD-sensitive devices.
• Select a grounding system, such as those listed below, to provide protection that meets the specific
service requirement.
Note: The use of a grounding system is desirable but not required to protect against ESD damage.
– Attach the ESD ground clip to any frame ground, ground braid, or green-wire ground.
– Use an ESD common ground or reference point when working on a double-insulated or
battery-operated system. You can use coax or connector-outside shells on these systems.
– Use the round ground-prong of the ac plug on ac-operated computers.
Grounding requirements
Electrical grounding of the computer is required for operator safety and correct system function. Proper
grounding of the electrical outlet can be verified by a certified electrician.
Safety notices (multi-lingual translations)
The caution and danger safety notices in this section are provided in the following languages:
• English
• Arabic
• Brazilian/Portuguese
• Chinese (simplified)
• Chinese (traditional)
• French
• German
• Hebrew
• Italian
• Korean
• Spanish
DANGER
Electrical current from power, telephone and communication cables is hazardous.
To avoid a shock hazard:
• Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration
of this product during an electrical storm.
• Connect all power cords to a properly wired and grounded electrical outlet.
• Connect to properly wired outlets any equipment that will be attached to this product.
6
Hardware Maintenance Manual
• When possible, use one hand only to connect or disconnect signal cables.
• Never turn on any equipment when there is evidence of fire, water, or structural damage.
• Disconnect the attached power cords, telecommunications systems, networks, and modems
before you open the device covers, unless instructed otherwise in the installation and configuration
procedures.
• Connect and disconnect cables as described in the following tables when installing, moving, or
opening covers on this product or attached devices.
To Connect
To Disconnect
1. Turn everything OFF.
1. Turn everything OFF.
2. First, attach all cables to devices.
3. Attach signal cables to connectors.
4. Attach power cords to outlet.
5. Turn device ON.
2. First, remove power cords from outlet.
3. Remove signal cables from connectors.
4. Remove all cables from devices.
CAUTION:
When replacing the lithium battery, use only Part Number 45C1566 or an equivalent type battery
recommended by the manufacturer. If your system has a module containing a lithium battery, replace
it only with the same module type made by the same manufacturer. The battery contains lithium and
can explode if not properly used, handled, or disposed of. Do not:
• Throw or immerse into water
• Heat to more than 100°C (212°F)
• Repair or disassemble
Dispose of the battery as required by local ordinances or regulations.
CAUTION:
When laser products (such as CD-ROMs, DVD-ROM drives, fiber optic devices, or transmitters) are
installed, note the following:
• Do not remove the covers. Removing the covers of the laser product could result in exposure to
hazardous laser radiation. There are no serviceable parts inside the device.
• Use of controls or adjustments or performance of procedures other than those specified herein
might result in hazardous radiation exposure.
DANGER
Some laser products contain an embedded Class 3A or Class 3B laser diode. Note the following:
Laser radiation when open. Do not stare into the beam, do not view directly with optical
instruments, and avoid direct exposure to the beam.
Chapter 2. Safety information
7
≥18 kg (37 lbs)
≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs)
CAUTION:
Use safe practices when lifting.
CAUTION:
The power control button on the device and the power switch on the power supply do not turn off
the electrical current supplied to the device. The device also might have more than one power
cord. To remove all electrical current from the device, ensure that all power cords are disconnected
from the power source.
2
1
8
Hardware Maintenance Manual
Chapter 2. Safety information
9
≥18 kg (37 lbs)
≥32 kg (70.5 lbs)
≥55 kg (121.2 lbs)
2
1
PERIGO
10 Hardware Maintenance Manual
A corrente elétrica proveniente de cabos de alimentação, de telefone e de comunicações é perigosa.
Para evitar risco de choque elétrico:
• Não conecte nem desconecte nenhum cabo ou execute instalação, manutenção ou reconfiguração
deste produto durante uma tempestade com raios.
• Conecte todos os cabos de alimentação a tomadas elétricas corretamente instaladas e aterradas.
• Todo equipamento que for conectado a este produto deve ser conectado a tomadas corretamente
instaladas.
• Quando possível, utilize apenas uma das mãos para conectar ou desconectar cabos de sinal.
• Nunca ligue nenhum equipamento quando houver evidência de fogo, água ou danos estruturais.
• Antes de abrir tampas de dispositivos, desconecte cabos de alimentação, sistemas de telecomunicação,
redes e modems conectados, a menos que especificado de maneira diferente nos procedimentos de
instalação e configuração.
• Conecte e desconecte os cabos conforme descrito na tabela apresentada a seguir ao instalar, mover ou
abrir tampas deste produto ou de dispositivos conectados.
Para Conectar:
Para Desconectar:
1. DESLIGUE Tudo.
1. DESLIGUE Tudo.
2. Primeiramente, conecte todos os cabos aos
dispositivos.
2. Primeiramente, remova os cabos de alimentação das
tomadas.
3. Conecte os cabos de sinal aos conectores.
4. Conecte os cabos de alimentação às tomadas.
5. LIGUE os dispositivos.
3. Remova os cabos de sinal dos conectores.
4. Remova todos os cabos dos dispositivos.
CUIDADO:
Ao substituir a bateria de lítio, utilize apenas uma bateria com Número de Peça 45C1566 ou um tipo
de bateria equivalente recomendado pelo Se o seu sistema possui um módulo com uma bateria de
lítio, substitua-o apenas por um módulo do mesmo tipo e do mesmo fabricante. A bateria contém lítio
e pode explodir se não for utilizada, manuseada ou descartada de maneira correta.
Não:
• Jogue ou coloque na água
• Aqueça a mais de 100°C (212°F)
• Conserte nem desmonte
Descarte a bateria conforme requerido pelas leis ou regulamentos locais.
PRECAUCIÓN:
Quando produtos a laser (como unidades de CD-ROMs, unidades de DVD-ROM, dispositivos de fibra ótica
ou transmissores) estiverem instalados, observe o seguinte:
Chapter 2. Safety information 11
• Não remova as tampas. A remoção das tampas de um produto a laser pode resultar em exposição
prejudicial à radiação de laser. Não existem peças que podem ser consertadas no interior do dispositivo.
• A utilização de controles ou ajustes ou a execução de procedimentos diferentes dos especificados aqui
pode resultar em exposição prejudicial à radiação.
PERIGO
Alguns produtos a laser contêm diodo de laser integrado da Classe 3A ou da Classe 3B. Observe o seguinte:
Radiação a laser quando aberto. Não olhe diretamente para o feixe a olho nu ou com instrumentos ópticos e
evite exposição direta ao feixe.
≥18 kg (37 lbs)
≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs)
CUIDADO:
Utilize procedimentos de segurança para levantar equipamentos.
CUIDADO:
O botão de controle de alimentação do dispositivo e o botão para ligar/desligar da fonte de alimentação
não desligam a corrente elétrica fornecida ao dispositivo. O dispositivo também pode ter mais de um cabo
de alimentação. Para remover toda a corrente elétrica do dispositivo, assegure que todos os cabos de
alimentação estejam desconectados da fonte de alimentação.
2
1
12 Hardware Maintenance Manual
Chapter 2. Safety information 13
2
1
14 Hardware Maintenance Manual
Chapter 2. Safety information 15
2
1
DANGER
Le courant électrique provenant de l'alimentation, du téléphone et des câbles de transmission peut présenter
un danger.
Pour éviter tout risque de choc électrique :
• Ne manipulez aucun câble et n'effectuez aucune opération d'installation, d'entretien ou de reconfiguration
de ce produit au cours d'un orage.
• Branchez tous les cordons d'alimentation sur un socle de prise de courant correctement câblé et mis à la
terre.
• Branchez sur des socles de prise de courant correctement câblés tout équipement connecté à ce produit.
• Lorsque cela est possible, n'utilisez qu'une seule main pour connecter ou déconnecter les câbles
d'interface.
• Ne mettez jamais un équipement sous tension en cas d'incendie ou d'inondation, ou en présence de
dommages matériels.
• Avant de retirer les carters de l'unité, mettez celle-ci hors tension et déconnectez ses cordons
d'alimentation, ainsi que les câbles qui la relient aux réseaux, aux systèmes de télécommunication et aux
modems (sauf instruction contraire mentionnée dans les procédures d'installation et de configuration).
• Lorsque vous installez, que vous déplacez, ou que vous manipulez le présent produit ou des périphériques
qui lui sont raccordés, reportez-vous aux instructions ci-dessous pour connecter et déconnecter les
différents cordons.
16 Hardware Maintenance Manual
Connexion
Déconnexion
1. Mettez les unités HORS TENSION.
1. Mettez les unités HORS TENSION.
2. Commencez par brancher tous les cordons sur les
unités.
2. Débranchez les cordons d'alimentation des prises.
3. Débranchez les câbles d'interface des connecteurs.
4. Débranchez tous les câbles des unités.
3. Branchez les câbles d'interface sur des connecteurs.
4. Branchez les cordons d'alimentation sur des prises.
5. Mettez les unités SOUS TENSION.
ATTENTION:
Remplacer la pile au lithium usagée par une pile de référence identique exclusivement, (référence
45C1566), ou suivre les instructions du fabricant qui en définit les équivalences. Si votre système est
doté d'un module contenant une pile au lithium, vous devez le remplacer uniquement par un module
identique, produit par le même fabricant. La pile contient du lithium et peut exploser en cas de
mauvaise utilisation, de mauvaise manipulation ou de mise au rebut inappropriée.
Ne pas :
• la jeter à l'eau,
• l'exposer à des températures supérieures à 100°C,
• chercher à la réparer ou à la démonter.
Ne pas mettre la pile à la poubelle. Pour la mise au rebut, se reporter à la réglementation en vigueur.
ATTENTION:
Si des produits à laser (tels que des unités de CD-ROM, de DVD-ROM, des unités à fibres optiques, ou
des émetteurs) sont installés, prenez connaissance des informations suivantes :
• Ne retirez pas le carter. En ouvrant l'unité de CD-ROM ou de DVD-ROM, vous vous exposez au
rayonnement dangereux du laser. Aucune pièce de l'unité n'est réparable.
• Pour éviter tout risque d'exposition au rayon laser, respectez les consignes de réglage et
d'utilisation des commandes, ainsi que les procédures décrites dans le présent manuel.
DANGER
Certains produits à laser contiennent une diode à laser intégrée de classe 3A ou 3B. Prenez
connaissance des informations suivantes:
Rayonnement laser lorsque le carter est ouvert. Evitez toute expositiondirecte au rayon laser. Evitez
de regarder fixement le faisceau ou del'observer à l'aide d'instruments optiques.
Chapter 2. Safety information 17
≥18 kg (37 lbs)
≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs)
ATTENTION:
Soulevez la machine avec précaution.
ATTENTION:
L'interrupteur de contrôle d'alimentation de l'unité et l'interrupteur dubloc d'alimentation ne coupent
pas le courant électrique alimentantl'unité. En outre, le système peut être équipé de plusieurs
cordonsd'alimentation. Pour mettre l'unité hors tension, vous devez déconnectertous les cordons
de la source d'alimentation.
2
1
VORSICHT
An Netz-, Telefon- und Datenleitungen können gefährliche Spannungen anliegen.
Aus Sicherheitsgründen:
• Bei Gewitter an diesem Gerät keine Kabel anschließen oder lösen. Ferner keine Installations-,
Wartungs- oder Rekonfigurationsarbeiten durchführen.
• Gerät nur an eine Schutzkontaktsteckdose mit ordnungsgemäß geerdetem Schutzkontakt
anschließen.
• Alle angeschlossenen Geräte ebenfalls an Schutzkontaktsteckdosen mit ordnungsgemäß
geerdetem Schutzkontakt anschließen.
• Die Signalkabel nach Möglichkeit einhändig anschließen oder lösen, um einen Stromschlag durch
Berühren von Oberflächen mit unterschiedlichem elektrischem Potenzial zu vermeiden.
• Geräte niemals einschalten, wenn Hinweise auf Feuer, Wasser oder Gebäudeschäden vorliegen.
18 Hardware Maintenance Manual
• Die Verbindung zu den angeschlossenen Netzkabeln, Telekommunikationssystemen, Netzwerken
und Modems ist vor dem Öffnen des Gehäuses zu unterbrechen, sofern in den Installations- und
Konfigurationsprozeduren keine anders lautenden Anweisungen enthalten sind.
• Zum Installieren, Transportieren und Öffnen der Abdeckungen des Computers oder der
angeschlossenen Einheiten die Kabel gemäß der folgenden Tabelle anschließen und abziehen.
Zum Anschließen der Kabel gehen Sie wie folgt vor
Zum Abziehen der Kabel gehen Sie wie folgt vor
1. Schalten Sie alle Einheiten AUS.
1. Schalten Sie alle Einheiten AUS.
2. Schließen Sie erst alle Kabel an die Einheiten an.
3. Schließen Sie die Signalkabel an die Buchsen an.
4. Schließen Sie die Netzkabel an die Steckdose an.
5. Schalten Sie die Einheit EIN.
2. Ziehen Sie zuerst alle Netzkabel aus den
Netzsteckdosen.
3. Ziehen Sie die Signalkabel aus den Buchsen.
4. Ziehen Sie alle Kabel von den Einheiten ab.
CAUTION:
Eine verbrauchte Lithiumbatterie nur durch eine Batterie mit der Teilenummer 45C1566 oder eine
gleichwertige, vom Hersteller empfohlene Batterie ersetzen. Enthält das System ein Modul mit einer
Lithiumbatterie, dieses nur durch ein Modul desselben Typs und von demselben Hersteller ersetzen.
Die Batterie enthält Lithium und kann bei unsachgemäßer Verwendung, Handhabung oder Entsorgung
explodieren.
Die Batterie nicht:
• mit Wasser in Berührung bringen.
• über 100 C erhitzen.
• reparieren oder zerlegen.
Die örtlichen Bestimmungen für die Entsorgung von Sondermüll beachten.
ACHTUNG:
Bei der Installation von Lasergeräten (wie CD-ROM-Laufwerken, DVD- aufwerken, Einheiten mit
Lichtwellenleitertechnik oder Sendern) Folgendes beachten:
• Die Abdeckungen nicht entfernen. Durch Entfernen der Abdeckungen des Lasergeräts können
gefährliche Laserstrahlungen freigesetzt werden. Das Gerät enthält keine zu wartenden Teile.
• Werden Steuerelemente, Einstellungen oder Durchführungen von Prozeduren anders als hier
angegeben verwendet, kann gefährliche Laserstrahlung auftreten.
VORSICHT
Einige Lasergeräte enthalten eine Laserdiode der Klasse 3A oder 3B. Beachten Sie Folgendes:
Chapter 2. Safety information 19
Laserstrahlung bei geöffneter Verkleidung. Nicht in den Strahl blicken. Keine Lupen oder Spiegel
verwenden. Strahlungsbereich meiden.
≥18 kg (37 lbs)
≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs)
ACHTUNG:
Arbeitsschutzrichtlinien beim Anheben der Maschine beachten.
ACHTUNG:
Mit dem Netzschalter an der Einheit und am Netzteil wird die Stromversorgung für die Einheit
nicht unterbrochen. Die Einheit kann auch mit mehreren Netzkabeln ausgestattet sein. Um die
Stromversorgung für die Einheit vollständig zu unterbrechen, müssen alle zum Gerät führenden
Netzkabel vom Netz getrennt werden.
2
1
20 Hardware Maintenance Manual
Chapter 2. Safety information 21
2
1
PERICOLO
La corrente elettrica proveniente dai cavi di alimentazione, del telefono e di comunicazione può essere
pericolosa.
Per evitare il rischio di scosse elettriche:
• Non collegare o scollegare qualsiasi cavo oppure effettuare l'installazione, la manutenzione o la
riconfigurazione del prodotto durante un temporale.
• Collegare tutti i fili elettrici a una presa di alimentazione correttamente cablata e dotata di messa a
terra.
• Collegare alle prese elettriche appropriate tutte le apparecchiature che verranno utilizzate per
questo prodotto.
22 Hardware Maintenance Manual
• Se possibile, utilizzare solo una mano per collegare o scollegare i cavi di segnale.
• Non accendere assolutamente apparecchiature in presenza di incendi, perdite d'acqua o danno
strutturale.
• Scollegare i cavi di alimentazione, i sistemi di telecomunicazione, le reti e il modem prima di
aprire i coperchi del dispositivo, salvo istruzioni contrarie relative alle procedure di installazione e
configurazione.
• Collegare e scollegare i cavi come descritto nella seguente tabella quando vengono effettuate
operazioni di installazione, spostamento o apertura dei coperchi di questo prodotto o delle unità
collegate.
Per collegarsi
Per scollegarsi
1. SPEGNERE le apparecchiature.
2. Innanzitutto, collegare tutti i cavi alle unità.
3. Collegare i cavi di segnale ai connettori.
4. Collegare i cavi di alimentazione alla presa.
5. Accendere l'unità.
1. SPEGNERE le apparecchiature.
2. Innanzitutto, rimuovere i cavi di alimentazione dalla
presa.
3. Rimuovere i cavi di segnale dai connettori.
4. Rimuovere tutti i cavi dalle unità.
ATTENZIONE:
Quando si sostituisce la batteria al litio, utilizzare solo il Numero parte 45C1566 o un tipo di batteria
equivalente consigliato dal produttore. Se sul sistema è presente un modulo che contiene una batteria
al litio, sostituirlo solo con un tipo di modulo dello stesso tipo della stessa casa di produzione. La
batteria contiene litio e può esplodere se usata, maneggiata o smaltita in modo non corretto.
Non:
• Gettare o immergere la batteria nell'acqua
• Riscaldarla ad una temperatura superiore ai 100 gradi C (212 gradi F)
• Smontarla, ricaricarla o tentare di ripararla
Le batterie usate vanno smaltite in accordo alla normativa in vigore (DPR 915/82 e successive
disposizioni e disposizioni locali).
ATTENZIONE:
Quando vengono installati prodotti laser (quali CD-ROM, unità DVD-ROM, unità a fibre ottiche o
trasmittenti), tener presente quanto segue:
• Non rimuovere gli sportelli. L'apertura di un'unità laser può determinare l'esposizione a radiazioni
laser pericolose. All'interno dell'unità non vi sono parti su cui effettuare l'assistenza tecnica.
• L'utilizzo di controlli, regolazioni o l'esecuzione di procedure non descritti nel presente manuale
possono provocare l'esposizione a radiazioni pericolose.
Chapter 2. Safety information 23
PERICOLO
Alcune unità laser contengono un diodo laser di Classe 3A o Classe 3B. Tener presente quanto segue:
Aprendo l'unità vengono emesse radiazioni laser. Non fissare il fascio, non guardarlo direttamente
con strumenti ottici ed evitare l'esposizione al fascio.
≥18 kg (37 lbs)
≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs)
ATTENZIONE:
Prestare attenzione nel sollevare l'apparecchiatura.
ATTENZIONE:
Il pulsante di controllo dell'alimentazione presente sull'unità e l'interruttore dell'alimentatore non
disattivano l'alimentazione corrente fornita all'unità. E' possibile che l'unità disponga di più cavi di
alimentazione. Per disattivare l'alimentazione dall'unità, accertarsi che tutti i cavi di alimentazione
siano scollegati dalla fonte di alimentazione.
2
1
24 Hardware Maintenance Manual
Chapter 2. Safety information 25
2
1
PELIGRO
La corriente eléctrica procedente de cables de alimentación, teléfonos y cables de comunicación puede
ser peligrosa.
Para evitar el riesgo de descarga eléctrica:
• No conecte ni desconecte los cables ni realice ninguna tarea de instalación, mantenimiento o
reconfiguración de este producto durante una tormenta eléctrica.
• Conecte todos los cables de alimentación a tomas de corriente debidamente cableadas y
conectadas a tierra.
• Cualquier equipo que se conecte a este producto también debe conectarse a tomas de corriente
debidamente cableadas.
• Siempre que sea posible, utilice una sola mano para conectar o desconectar los cables de señal.
• No encienda nunca un equipo cuando hay señales de fuego, agua o daños estructurales.
26 Hardware Maintenance Manual
• Desconecte los cables de alimentación, los sistemas de telecomunicaciones, las redes y los
módems conectados antes de abrir las cubiertas de los dispositivos, a menos que se indique lo
contrario en los procedimientos de instalación y configuración.
• Conecte y desconecte los cables, como se describe en la tabla siguiente, cuando instale, mueva o
abra las cubiertas de este producto o de los dispositivos conectados.
Para conectar
Para desconectar
1. APÁGUELO todo.
1. APÁGUELO todo.
2. En primer lugar, conecte todos los cables a los
dispositivos.
2. En primer lugar, desenchufe los cables de alimentación
de las tomas de corriente.
3. Conecte los cables de señal a los conectores.
3. Desconecte los cables de señal de los conectores.
4. Desconecte todos los cables de los dispositivos.
4. Enchufe los cables de alimentación a las tomas de
corriente.
5. Encienda el dispositivo.
PRECAUCIÓN:
Cuando sustituya una batería de litio, utilice solamente una batería número de pieza 45C1566 u otra
de tipo equivalente recomendada por el fabricante. Si su sistema dispone de un módulo que contiene
una batería de litio, reemplácelo sólo con el mismo tipo de módulo, del mismo fabricante. La batería
contiene litio y puede explotar si no se utiliza, manipula o desecha correctamente.
No debe:
• Arrojarla al agua o sumergirla en ella
• Exponerla a temperaturas superiores a 100°C (212°F)
• Repararla o desmontarla
Deshágase de la batería según especifiquen las leyes o normas locales.
PRECAUCIÓN:
Cuando haya productos láser (como unidades de CD-ROM, unidades de DVD, dispositivos de fibra
óptica o transmisores) instalados, tenga en cuenta lo siguiente:
• No quite las cubiertas. Si quita las cubiertas del producto láser, podría quedar expuesto a radiación
láser peligrosa. Dentro del dispositivo no existe ninguna pieza que requiera servicio técnico.
• Si usa controles o ajustes o realiza procedimientos que no sean los especificados aquí, podría
exponerse a radiaciones peligrosas.
PELIGRO
Chapter 2. Safety information 27
Algunos productos láser tienen incorporado un diodo láser de clase 3A o clase 3B. Tenga en cuenta lo
siguiente:
Cuando se abre, queda expuesto a radiación láser. No mire directamente al rayo láser, ni siquiera con
instrumentos ópticos, y evite exponerse directamente al rayo láser.
≥18 kg (37 lbs)
≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs)
PRECAUCIÓN:
Adopte procedimientos seguros al levantar el equipo.
PRECAUCIÓN:
El botón de control de alimentación del dispositivo y el interruptor de alimentación de la fuente de
alimentación no desconectan la corriente eléctrica suministrada al dispositivo. Además, el dispositivo
podría tener más de un cable de alimentación. Para suprimir toda la corriente eléctrica del dispositivo,
asegúrese de que todos los cables de alimentación estén desconectados de la toma de corriente.
2
1
28 Hardware Maintenance Manual
Chapter 3. General information
This chapter provides general information that applies to all machine types supported by this publication.
The ThinkVantage Productivity Center program
Use the ThinkVantage® Productivity Center program for general information about the use, operation, and
maintenance of the computer. The ThinkVantage Productivity Center program also contains information to
help solve problems and get repair service or other technical assistance. The ThinkVantage Productivity
Center program is preinstalled on most ThinkCentre products.
Additional information resources
If you have Internet access, the most up-to-date information for the computer is available from the World
Wide Web.
You can find the following information:
• Customer Replaceable Unit (CRU) removal and installation instructions
• Publications
• Troubleshooting information
• Parts information
• Downloads and drivers
• Links to other useful sources of information
To access this information, point your browser to http://www.lenovo.com/support/.
Specifications
This section lists the physical specifications for your computer.
© Copyright Lenovo 2005, 2010
29
Dimensions
Width: 275 mm (10.83 in.)
Height: 81 mm (3.19 in.)
Depth: 242 mm (9.53 in.)
Weight
Note: The weight does not include the power supply or any external cables.
Minimum configuration as shipped: 3.27 kg (7.2 lbs)
Maximum configuration: 3.72 kg (8.2 lbs)
Environment
• Air temperature:
– Operating at 0 - 3000 ft (914.4 m): 10° to 35°C (50° to 95°F)
– Non-operating: -40° to 60°C (-40° to 140°F)
– Maximum altitude: 3000 ft (914.4 m)
Note: The maximum altitude, 3000 ft. (914.4 m), is the maximum altitude at which the specified air temperatures
apply. At higher altitudes, the maximum air temperatures are lower than those specified.
• Humidity (non-condensing):
Operating: 10% to 80%
Non-operating: 10% to 90%
Electrical input
• Input voltage:
– Low range:
Minimum: 100 V ac
Maximum: 127 V ac
Input frequency range: 50/60 Hz
– High range:
Minimum: 200 V ac
Maximum: 240 V ac
Input frequency range: 50/60 Hz
– Input kilovolt-amperes (kVA) (approximate):
– Minimum configuration as shipped: 0.05 kVA (all machine types)
–
Maximum configuration:
0.12 kVA (Machine Types 6393, 6394, 6395, 6396, 6397)
Note: Power consumption and heat output vary depending on the number and type of optional features
installed and the power-management optional features in use.
30 Hardware Maintenance Manual
Chapter 4. General Checkout
Attention
The drives in the computer you are servicing might have been rearranged or the drive startup sequence
changed. Be extremely careful during write operations such as copying, saving, or formatting. Data or
programs can be overwritten if you select an incorrect drive.
General error messages appear if a problem or conflict is found by an application program, the operating
system, or both. For an explanation of these messages, refer to the information supplied with that software
package.
Before replacing any FRUs, ensure that the latest level of BIOS is installed on the system. A down-level BIOS
might cause false errors and unnecessary replacement of the system board. For more information on how to
Use the following procedure to help determine the cause of the problem:
1. Power-off the computer and all external devices.
2. Check all cables and power cords.
3. Set all display controls to the middle position.
4. Power-on all external devices.
5. Power-on the computer.
• Look for displayed error codes
• Listen for beep codes
• Look for readable instructions or a main menu on the display.
If you did not receive the correct response, proceed to step 6 on page 31.
If you do receive the correct response, run the diagnostics. .See “Running diagnostics from the CD or
6. Look at the following conditions and follow the instructions:
Checking for power problems
If the computer does not turn on when the power switch is pressed, use the following procedure to help
troubleshoot.
1. Press the power switch to turn on the computer. Check the power indicator LED next to the power switch.
• If the LED is illuminated (on), the computer power is OK. Attempt to run the diagnostics. See “Running
• If the LED is not illuminated (off), go to step 2 on page 31
2. Check the status of the power indicator LED on the AC/DC power adapter.
• If the LED is illuminated (on), go to step 7 on page 32.
• If the LED is not illuminated (off), go to the next step 3 on page 31.
3. Verify that the power cord is properly connected to an AC power outlet.
4. Verify that you are using a good AC power outlet. Plug another device into the outlet or contact the power
company or supplier to verify that the outlet is working correctly .
© Copyright Lenovo 2005, 2010
31
5. Check the power cord continuity.
6. Replace the AC/DC power adapter.
7. Verify that the power cord from the AC/DC power adapter to the computer is properly connected. See
on page 68. Reseat the cable from the Power switch/LED assembly to the system board.
10.Replace the power switch/LED assembly.
Problem determination tips
Due to the variety of hardware and software combinations that can be encountered, use the following
information to assist you in problem determination. If possible, have this information available when
requesting assistance from Service Support and Engineering functions.
• Machine type and model
• Processor or hard disk upgrades
• Failure symptom
– Do diagnostics indicate a failure?
– What, when, where, single, or multiple systems?
– Is the failure repeatable?
– Has this configuration ever worked?
– If it has been working, what changes were made prior to it failing?
– Is this the original reported failure?
• Diagnostics version
– Type and version level
• Hardware configuration
– Print (print screen) configuration currently in use
– BIOS level
• Operating system software
– Type and version level
Notes: To eliminate confusion, identical systems are considered identical only if they:
1. Are the exact machine type and models
2. Have the same BIOS level
3. Have the same adapters/attachments in the same locations
4. Have the same address jumpers/terminators/cabling
5. Have the same software versions and levels
6. Have the same Diagnostic Diskettes (version)
7. Have the same configuration options set in the system
8. Have the same setup for the operating system control files
Comparing the configuration and software set-up between “working and non-working” systems will often
lead to problem resolution.
32 Hardware Maintenance Manual
Chapter 5. Diagnostics
Diagnostic programs are used to test hardware components of your computer and report
operating-system-controlled settings that can cause hardware failures. There are two diagnostic programs
preinstalled on your computer to help you diagnose problems:
• PC-Doctor for Windows (used when diagnosing problems while running the Windows operating system)
• PC-Doctor for Windows PE (used when your Windows operating system will not start)
Notes:
1. You can also download the latest version of the PC-Doctor for Windows and PC-Doctor for DOS
diagnostic programs from http://www.lenovo.com/support/.
2. If you are unable to isolate and repair the problem yourself by running the applicable version
of PC-Doctor, click the Save Button in the PC-Doctor-log-file display. You will need to have all
problem-related log files available when you speak to a Lenovo technical support representative.
PC-Doctor for Windows
PC-Doctor for Windows is a diagnostic program that works through the Windows operating system. The
PC-Doctor for Windows diagnostic program enables you to view symptoms and solutions for computer
problems, access the Lenovo troubleshooting center, update system drivers, and review system information.
To run PC-Doctor for Windows, open the Start menu from the Windows desktop, select All Programs, select
PC-Doctor for Windows, and click PC-Doctor for Windows. Follow the instructions on the screen.
For additional information about running the diagnostic program, refer to the PC-Doctor for Windows
help system.
If you still suspect a problem after PC-Doctor for Windows runs successfully, run PC-Doctor for DOS or
PC-Doctor for Windows PE to help you diagnose the computer problem.
PC Doctor for Windows also has problem determination aids that determine software and usage problems.
PC-Doctor for Windows PE
The PC-Doctor for Windows PE diagnostic program is part of the Rescue and Recovery™ workspace on
each Lenovo computer. Use PC-Doctor for Windows PE, if you are unable to start the Windows operating
system or if PC-Doctor for Windows has not been successful in isolating a possible problem.
Running diagnostics from the Rescue and Recovery workspace
You can run the PC-Doctor for Windows PE diagnostic program from the Rescue and Recovery workspace.
To run diagnostics from the Rescue and Recovery workspace, use the following procedure:
1. Shut down the operating system and turn off the computer.
2. Repeatedly press and release the F11 key as you turn on the computer.
3. When you hear beeps or see a logo screen, stop pressing the F11 key. The Rescue and Recovery
workspace opens.
4. From the Rescue and Recovery workspace, select Diagnose hardware.
5. The diagnostic program opens automatically. Select the diagnostic test you want to run. Press the F1
key for additional help.
© Copyright Lenovo 2005, 2010
33
6. Follow the instructions on the screen.
Note: Rescue media includes PC-Doctor for Windows PE. For more information about rescue media,
see the User Guide for the computer.
PC-Doctor for DOS
Use PC-Doctor for DOS, if you are unable to start the Windows operating system or if PC-Doctor for
Windows has not been successful in isolating a possible problem. You can run PC-Doctor for DOS from a
diagnostic CD image or diagnostic diskettes that have been created.
Note: It is important to create a diagnostic CD image or diagnostic diskettes in case PC-Doctor for Windows
PE cannot be run from the Rescue and Recovery workspace.
Creating a diagnostic CD image
To create a diagnostic CD image, download a self-starting bootable CD image (known as an .iso image)
of the diagnostic program from http://www.lenovo.com/support/. After you download the image, you
can create the CD using any CD burning software.
If the computer does not have a CD burner or you do not have Internet access, see “Creating diagnostic
Creating diagnostic diskettes
To create diagnostic diskettes, download the PC-Doctor for DOS diagnostic program from
http://www.lenovo.com/support/ onto two blank, formatted diskettes.
If you do not have Internet access, create the diagnostic diskettes using the following procedure:
Note: You will need a diskette drive on the computer or a USB diskette drive to complete this procedure.
1. Shut down the operating system and turn off the computer.
2. If you are using a USB diskette drive, plug it into the computer.
3. Repeatedly press and release the F11 key as you turn on the computer.
4. When you hear beeps or see a logo screen, stop pressing the F11 key. The Rescue and Recovery
workspace opens.
Note: For some models, press the Esc key to enter Rescue and Recovery.
5. From the Rescue and Recovery workspace, select Create diagnostic disks.
6. Follow the instructions on the screen.
7. When prompted, insert a blank, formatted diskette into the diskette drive and continue to follow the
instructions on the screen.
8. When the operation is complete, remove the diskette and click Quit.
9. Insert another blank, formatted diskette into the diskette drive and continue to follow the instructions on
the screen.
10.When the operation is complete, remove the diskette and click Quit.
Running diagnostics from the CD or diskettes
To run diagnostics from the diagnostic CD image or diagnostic diskettes that you created, use the following
procedure:
1. Make sure the computer is turned off.
2. If you are running diagnostics from diskettes using a USB diskette drive, plug in the USB device.
34 Hardware Maintenance Manual
3. Insert the CD into the optical drive or the first diagnostic diskette into the diskette drive.
4. Restart the computer.
Note: If the diagnostic program does not start, you might not have your optical drive or diskette drive set
as a startable device. See “Selecting a startup device” on page 40 for instructions on how to change
the startup device.
5. When the diagnostics program opens, follow the instructions on the screen.
Note: If you are running diagnostics from a diskette, when prompted, remove the first diskette and
insert the second diskette.
6. When the program finishes, be sure to remove the CD or diskette from the drive.
7. Select the diagnostic test you want to run. Press the F1 key for additional help.
Navigating through the diagnostics programs
Use the cursor movement keys to navigate within the menus.
• The Enter key is used to select a menu item.
• The Esc key is used to back up to the previous menu.
• For online help select F1.
Running tests
There are four ways to run the diagnostic tests.
• Using the cursor movement keys, highlight Run Normal Test or Run Quick Test from the Diagnostics
menu and then press Enter. This automatically runs a pre-defined group of tests from each test category.
Run Normal Test runs a more extensive set of tests than does Run Quick Test and takes longer to
complete.
• Press F5 to automatically run all selected tests in all categories.
• From within a test category, press Ctrl-Enter to automatically run only the selected tests in that category.
• Using the cursor movement keys, highlight a single test within a test category, and then press Enter.
This runs only that test.
Press Esc at any time to stop the testing process.
Test results (N/A, PASSED, FAILED, ABORTED) are displayed in the field beside the test description and in
To select one or more tests, use the following procedure.
1. Open the corresponding test category.
2. Using the cursor movement keys, highlight the desired test.
3. Press the space bar. A selected test is marked by >>. Pressing the space bar again de-selects a test
and removes the >>.
4. Repeat steps 2 and 3 above to select all desired tests.
Test results
Diagnostics test results produce the following error code format:
Failure Type
DeviceID
Date
Text
Function Code
ChkDigits
Chapter 5. Diagnostics 35
• Function Code:
Represents the feature or function within the PC.
• Failure Type:
Represents the type of error encountered.
• DeviceID:
Contains the component's unit-ID which corresponds to either a fixed disk drive, removable media drive,
processor, specific RIMM, or a device on the PCI bus.
• Date:
Contains the date when the diagnostic test was run. The date is retrieved from CMOS and displayed
using the YYYYMMDD format.
• ChkDigits:
Contains a 2-digit check-digit value to ensure the following:
– Diagnostics were run on the specified date.
– Diagnostics were run on the specified computer.
– The diagnostic error code is recorded correctly.
• Text:
Description of the error.
Quick and Full erase - hard drive
The diagnostics program offers two hard drive format utilities:
• Quick Erase Hard Drive
• Full Erase Hard Drive
The Quick Erase Hard Drive provides a DOS utility that performs the following:
• Destroys the Master Boot Record (MBR) on the hard drive.
• Destroys all copies of the FAT Table on all partitions (both the master and backup).
• Destroys the partition table.
• Provides messages that warn the user that this is a non-recoverable process.
The Full Erase Hard Drive provides a DOS utility that performs the following:
• Performs all the steps in Quick Erase.
• Provides a DOS utility that writes random data to all sectors of the hard drive.
• Provides an estimate of time to completion along with a visual representation of completion status.
• Provides messages that warn the user about non-recoverable process.
Important: Make sure that all data is backed up before using the Quick or Full Erase functions.
To select the Quick Erase or Full Erase Hard Drive utility, use the following procedure:
1. Select the UTILITY option on the toolbar and press Enter.
2. Select either the QUICK ERASE or FULL ERASE HARD DISK option and follow the instructions.
Viewing the test log
Errors reported by the diagnostic test will be displayed by the program as a failed test.
36 Hardware Maintenance Manual
To view details of a failure or to view a list of test results, use the following procedure from any test category
screen:
1. Press F3 to activate the log file.
2. Press F3 again to save the file to diskette or press F2 to print the file.
Chapter 5. Diagnostics 37
38 Hardware Maintenance Manual
Chapter 6. Using the Setup Utility
The Setup Utility program is used to view and change the configuration settings of the computer, regardless
of which operating system you are using. However, the operating-system settings might override any similar
settings in the Setup Utility program.
Starting the Setup Utility program
To start the Setup Utility program, do the following:
1. If the computer is already on when you start this procedure, shut down the operating system and turn
off the computer.
2. Press and hold the F1 key then turn on the computer. When you hear multiple beeps, release the F1 key.
Notes:
a. If you are using a USB keyboard and the Setup Utility program does not display using this method,
repeatedly press and release the F1 key rather than leaving it pressed when turning on the computer.
b. If a user password or an administrator password has been set, the Setup Utility program menu is not
The Setup Utility might start automatically when POST detects that hardware has been removed or new
hardware has been installed in the computer.
Viewing and changing settings
The Setup Utility program menu lists items that identify system configuration topics. To view or change
When working with the Setup Utility program menu, you must use the keyboard. The keys used to perform
various tasks are displayed at the bottom of each screen.
Using passwords
By using the Setup Utility program, you can set passwords to prevent unauthorized persons from gaining
types of passwords are available:
• User Password
• Administrator Password
You do not have to set any passwords to use the computer. However, if you decide to set any passwords,
read the following sections.
Password considerations
A password can be any combination of up to twelve characters (a-z and 0-9) and symbols. For security
reasons, it is a good idea to use a strong password that cannot be easily compromised. Passwords should
adhere to the following rules:
• Have at least eight characters in length
• Contain at least one alphabetic character and one numeric character
© Copyright Lenovo 2005, 2010
39
• Setup Utility program and hard disk drive passwords are not case sensitive
• Not be your name or your user name
• Not be a common word or a common name
• Be significantly different from your previous password
User Password
When a User Password is set, the computer cannot be used until a valid password is typed from the
keyboard.
Administrator Password
When an Administrator Password is set, it deters unauthorized persons from changing configuration
settings. If you are responsible for maintaining the settings of several computers, you might want to set an
Administrator Password.
After you set an Administrator Password, a password prompt is displayed each time you try to access the
Setup Utility program.
If both the user and administrator passwords are set, you can type either password. However, to change
any configuration settings, you must use your administrator password.
Setting, changing, and deleting a password
To set, change, or delete a password, do the following:
Note: A password can be any combination of up to twelve characters (A- Z, a-z, and 0-9). For more
2. From the Setup Utility program menu, select Security.
3. Select Set Passwords. Read the information displayed on the right side of the screen.
Selecting a startup device
If the computer does not start up (boot) from a device such as the CD-ROM, diskette, or hard disk as
expected, use one of the following procedures to select a startup device.
Selecting a temporary startup device
Use this procedure to startup from any boot device.
Note: Not all CDs, hard disks, and diskettes are bootable.
1. Turn off the computer.
2. Press and hold the F12 key then turn on the computer. When the Startup Device Menu appears, release
the F12 key.
Note: If you are using a USB keyboard and the Startup Device Menu does not display using this method,
repeatedly press and release the F12 key rather than leaving it pressed when turning on the computer.
3. Select the desired startup device from the Startup Device Menu and press Enter to begin.
Note: Selecting a startup device from the Startup Device menu does not permanently change the startup
sequence.
40 Hardware Maintenance Manual
Selecting or changing the startup device sequence
To view or permanently change the configured startup device sequence, do the following:
2. Select Startup.
3. Select Startup Sequence. See the information displayed on the right side of the screen.
4. Select the devices for the Primary Startup Sequence, the Automatic Startup Sequence, and the Error
Startup Sequence.
5. Select Exit from the Setup Utility menu and then Save Settings or Save and exit the Setup Utility.
If you have changed these settings and want to return to the default settings, select Load Default Settings
on the Exit menu.
Advanced settings
On some computer models the Advanced settings menu includes a setting to Enable/Disable
HyperThreading. This feature works only with HyperThreading-aware operating systems, such as Microsoft
Windows XP and Windows Vista™. The default setting for HyperThreading is Enabled. However, if you
select Set Defaults and are using an operating system other than Windows XP or Windows Vista, the
computer performance might be degraded. Therefore, you should always set HyperThreading to Disabled
unless you are sure your operating system supports HyperThreading.
Exiting from the Setup Utility program
When you finish viewing or changing settings, press Esc to return to the Setup Utility program menu (you
might have to press Esc several times). If you want to save the new settings, select Save & Exit Setup
before you exit. Otherwise, your changes will not be saved.
Chapter 6. Using the Setup Utility 41
42 Hardware Maintenance Manual
Chapter 7. Symptom-to-FRU Index
The Symptom-to-FRU index lists error symptoms and possible causes. The most likely cause is listed first.
decide which FRUs to have available when servicing a computer. If you are unable to correct the problem
Notes:
• If you have both an error message and an incorrect audio response, diagnose the error message first.
• If you cannot run the diagnostic tests or you get a diagnostic error code when running a test, but did receive a
POST error message, diagnose the POST error message first.
• If you did not receive any error message, look for a description of your error symptoms in the first part of this index.
Hard disk drive boot error
A hard disk drive boot error (error codes 1962 and I999030X) can have the following causes.
Error
FRU/Action
The start-up drive is not in the boot sequence in
configuration.
Check the configuration and ensure the start-up drive is
in the boot sequence.
No operating system installed on the boot drive.
The boot sector on the start-up drive is corrupted.
Install an operating system on the boot drive.
The drive must be formatted, do the following:
1. Attempt to back-up the data on the failing hard disk
drive.
2. Using the operating systems programs, format the
hard disk drive.
The drive is defective.
Replace the hard disk drive.
Diagnostic error codes
Refer to the following diagnostic error codes when using the diagnostic tests. See “Running tests” on page
35 for the specific type for information about the Diagnostic programs.
In the following index, X can represent any number.
Diagnostic Error Code
FRU/Action
No action
000-000-XXX BIOS Test Passed
000-002-XXX BIOS Timeout
2. System board
000-024-XXX BIOS Addressing test failure
2. System board
000-025-XXX BIOS Checksum Value error
2. System board
© Copyright Lenovo 2005, 2010
43
Diagnostic Error Code
FRU/Action
000-026-XXX FLASH data error
2. System board
000-027-XXX BIOS Configuration/Setup error
1. Run Setup
3. System board
1. Reboot the system
000-034-XXX BIOS Buffer Allocation failure
3. Run memory test
4. System board
000-035-XXX BIOS Reset Condition detected
000-036-XXX BIOS Register error
2. System board
2. System board
000-038-XXX BIOS Extension failure
2. Adapter card
3. System board
000-039-XXX BIOS DMI data error
2. System board
000-195-XXX BIOS Test aborted by user
Information only Re-start the test, if necessary
1. Press F3 to review the log file
000-196-XXX BIOS test halt, error threshold exceeded
2. Re-start the test to reset the log file
1. Make sure the component that is called out
page 39
000-197-XXX BIOS test warning
2. Re-run test
3. Replace the component that is called out in warning
statement
4. Replace the component under test
1. Make sure the component that is called out
page 39
000-198-XXX BIOS test aborted
000-199-XXX BIOS test failed, cause unknown
2. Flash the system and re-test
3. Replace component under function test
44 Hardware Maintenance Manual
Diagnostic Error Code
FRU/Action
000-250-XXX BIOS APM failure
2. System board
000-270-XXX BIOS ACPI failure
2. System board
No action
001-000-XXX System Test Passed
001-00X-XXX System Error
System board
System board
System board
001-01X-XXX System Error
001-024-XXX System Addressing test failure
001-025-XXX System Checksum Value error
2. System board
001-026-XXX System FLASH data error
2. System board
001-027-XXX System Configuration/Setup error
1. Run Setup
3. System board
System board
001-032-XXX System Device Controller failure
1. Reboot the system
001-034-XXX System Device Buffer Allocation failure
3. Run memory test
4. System board
001-035-XXX System Device Reset condition detected
001-036-XXX System Register error
System board
System board
1. Adapter card
2. System board
001-038-XXX System Extension failure
001-039-XXX System DMI data structure error
2. System board
001-040-XXX System IRQ failure
1. Power-off/on system and re-test
2. System board
001-041-XXX System DMA failure
1. Power-off/on system and re-test
2. System board
001-195-XXX System Test aborted by user
Information only Re-start the test, if necessary
1. Press F3 to review the log file
001-196-XXX System test halt, error threshold exceeded
2. Re-start the test to reset the log file
Chapter 7. Symptom-to-FRU Index 45
Diagnostic Error Code
FRU/Action
1. Make sure the component that is called out
page 39
001-197-XXX System test warning
2. Re-run test
3. Replace the component that is called out in warning
statement
4. Replace the component under test
1. If a component is called out, make sure it is
page 39
001-198-XXX System test aborted
001-199-XXX System test failed, cause unknown
2. Flash the system and re-test
3. Replace component under function test
001-250-XXX System ECC error
System board
System board
001-254-XXX 001-255-XXX 001-256-XXX 001-257-XXX
System DMA error
001-260-XXX 001-264-XXX System IRQ error
System board
001-268-XXX System IRQ1 failure
1. Device on IRQ1
2. System board
001-269-XXX System IRQ2 failure
001-270-XXX System IRQ3 failure
001-271-XXX System IRQ4 failure
001-272-XXX System IRQ5 failure
001-273-XXX System IRQ6 (diskette drive) failure
1. Device on IRQ2
2. System board
1. Device on IRQ3
2. System board
1. Device on IRQ4
2. System board
1. Device on IRQ5
2. System board
1. Diskette Cable
2. Diskette drive
3. System board
001-274-XXX System IRQ7 failure
001-275-XXX System IRQ8 failure
001-276-XXX System IRQ9 failure
001-277-XXX System IRQ10 failure
1. Device on IRQ7
2. System board
1. Device on IRQ8
2. System board
1. Device on IRQ9
2. System board
1. Device on IRQ10
2. System board
46 Hardware Maintenance Manual
Diagnostic Error Code
FRU/Action
001-278-XXX System IRQ11 failure
1. Device on IRQ11
2. System board
001-279-XXX System IRQ12 failure
1. Device on IRQ12
2. System board
001-280-XXX System IRQ13 failure
1. Device on IRQ13
2. System board
1. Hard disk drive cable
2. Hard disk drive
3. System board
001-281-XXX System IRQ14 (hard disk drive) failure
001-282-XXX System IRQ15 failure
1. Device on IRQ15
2. System board
001-286-XXX 001-287-XXX 001-288-XXX System Timer System board
failure
001-292-XXX System CMOS RAM error
001-293-XXX System CMOS Battery
1. Run Setup and re-test
2. System board
1. CMOS Battery
2. System board
001-298-XXX System RTC date/time update failure
2. System board
System board
System board
001-299-XXX System RTC periodic interrupt failure
001-300-XXX System RTC Alarm failure
001-301-XXX System RTC Century byte error
2. System board
No action
005-000-XXX Video Test Passed
005-00X-XXX Video error
1. Video card, if installed
2. System board
005-010-XXX 005-011-XXX 005-012-XXX 005-013-XXX 1. Video card, if installed
Video Signal failure
2. System board
1. Video Ram
005-016-XXX Video Simple Pattern test failure
2. Video card, if installed
3. System board
005-024-XXX Video Addressing test failure
005-025-XXX Video Checksum Value error
005-027-XXX Video Configuration/Setup error
1. Video card, if installed
2. System board
1. Video card, if installed
2. System board
1. Run Setup
2. Video drivers update
3. Video card, if installed
4. System board
Chapter 7. Symptom-to-FRU Index 47
Diagnostic Error Code
FRU/Action
1. Video cable
005-031-XXX Video Device Cable failure
2. Monitor
3. Video card, if installed
4. System board
1. Video card, if installed
2. System board
005-032-XXX Video Device Controller failure
005-036-XXX Video Register error
1. Video card, if installed
2. System board
1. Video card, if installed
2. System board
005-038-XXX System BIOS extension failure
005-040-XXX Video IRQ failure
1. Video card, if installed
2. System board
005-195-XXX Video Test aborted by user
Information only Re-start the test, if necessary
1. Press F3 to review the log file
005-196-XXX Video test halt, error threshold exceeded
2. Re-start the test to reset the log file
005-197-XXX Video test warning
1. Make sure the component that is called out
page 39
2. Re-run test
3. Replace the component called out in warning
statement
4. Replace the component under test
005-198-XXX Video test aborted
1. If a component is called out, make sure it is
page 39
005-199-XXX Video test failed, cause unknown
3. Replace component under function test
1. Video card, if installed
2. System board
005-2XX-XXX 005-3XX-XXX Video subsystem error
006-000-XXX Diskette interface Test Passed
No action
006-0XX-XXX Diskette interface error
1. Diskette drive Cable
2. Diskette drive
3. System board
006-195-XXX Diskette interface Test aborted by user
Information only Re-start the test, if necessary
1. Press F3 to review the log file
006-196-XXX Diskette interface test halt, error threshold
exceeded
2. Re-start the test to reset the log file
48 Hardware Maintenance Manual
Diagnostic Error Code
FRU/Action
006-197-XXX Diskette interface test warning
1. If a component is called out, make sure it is
connected and/or enabled
2. Re-run test
3. Replace the component that is called out in warning
statement
4. Replace the component under test
006-198-XXX Diskette interface test aborted
1. If a component is called out, make sure it is
connected and/or enabled
006-199-XXX Diskette interface test failed, cause
unknown
2. Flash the system and re-test
3. Replace component under function test
1. Diskette drive cable
006-25X-XXX Diskette interface Error
2. Diskette drive
3. System board
No action
015-000-XXX USB port Interface Test Passed
015-001-XXX USB port Presence
1. Remove USB device(s) and re-test
2. System board
015-002-XXX USB port Timeout
1. Remove USB device(s) and re-test
2. System board
015-015-XXX USB port External Loopback failure
015-027-XXX USB port Configuration/Setup error
1. Remove USB device(s) and re-test
2. System board
2. System board
System board
015-032-XXX USB port Device Controller failure
1. Reboot the system
015-034-XXX USB port buffer allocation failure
3. Run memory test
4. System board
015-035-XXX USB port Reset condition detected
1. Remove USB device(s) and re-test
2. System board
015-036-XXX USB port Register error
System board
1. Run setup and check for conflicts
015-040-XXX USB port IRQ failure
3. System board
015-195-XXX USB port Test aborted by user
Information only Re-start the test, if necessary
1. Press F3 to review the log file
015-196-XXX USB port test halt, error threshold exceeded
2. Re-start the test to reset the log file
Chapter 7. Symptom-to-FRU Index 49
Diagnostic Error Code
FRU/Action
1. Make sure the component that is called out
page 39
015-197-XXX USB port test warning
2. Re-run test
3. Replace the component that is called out in warning
statement
4. Replace the component under test
1. If a component is called out, make sure it is
page 39
015-198-XXX USB port test aborted
015-199-XXX USB port test failed, cause unknown
3. Replace component under function test
No action
018-000-XXX PCI Card Test Passed
1. Riser card, if installed
018-0XX-XXX PCI Card Failure
2. System board
018-195-XXX PCI Card Test aborted by user
018-196-XXX PCI Card test halt, error threshold exceeded
018-197-XXX PCI Card test warning
1. PCI card
2. Information only Re-start the test, if necessary
1. Press F3 to review the log file
2. Re-start the test to reset the log file
1. Make sure the component that is called out
page 39
2. Re-run test
3. Replace the component that is called out in warning
statement
4. Replace the component under test
1. If a component is called out, make sure it is
page 39
018-198-XXX PCI Card test aborted
018-199-XXX PCI Card test failed, cause unknown
3. Replace component under function test
50 Hardware Maintenance Manual
Diagnostic Error Code
FRU/Action
018-250-XXX PCI Card Services error
1. PCI card
2. Riser card, if installed
3. System board
No action
020-000-XXX PCI Interface Test Passed
020-0XX-XXX PCI Interface error
1. PCI card
2. Riser card, if installed
3. System board
020-195-XXX PCI Test aborted by user
Information only Re-start the test, if necessary
1. Press F3 to review the log file
020-196-XXX PCI test halt, error threshold exceeded
2. Re-start the test to reset the log file
1. Make sure the component that is called out
page 39
020-197-XXX PCI test warning
2. Re-run test
3. Replace the component that is called out in warning
statement
4. Replace the component under test
1. If a component is called out, make sure it is
page 39
020-198-XXX PCI test aborted
020-199-XXX PCI test failed, cause unknown
3. Replace component under function test
020-262-XXXPCI system error
1. PCI card
2. Riser card, if installed
3. System board
No action
025-000-XXXIDE interface Test Passed
025-00X-XXX 025-01X-XXX IDE interface failure
1. IDE signal cable
2. Check power supply voltages
3. Reseat IDE signal cable
4. IDE device
5. System board
1. IDE signal cable
025-027-XXX IDE interface Configuration/Setup error
3. Reseat IDE signal cable
4. IDE device
5. System board
Chapter 7. Symptom-to-FRU Index 51
Diagnostic Error Code
FRU/Action
025-02X-XXX 025-03X-XXX 025-04X-XXX IDE Interface 1. IDE signal cable
failure
2. Check AC/DC power adapter
3. Reseat IDE signal cable
4. IDE device
5. System board
025-195-XXX IDE interface Test aborted by user
Information only Re-start the test, if necessary
1. Press F3 to review the log file
025-196-XXX IDE interface test halt, error threshold
exceeded
2. Re-start the test to reset the log file
025-197-XXX IDE interface test warning
1. Make sure the component that is called out
page 39
2. Re-run test
3. Replace the component that is called out in warning
statement
4. Replace the component under test
025-198-XXX IDE interface test aborted
1. If a component is called out, make sure it is
page 39
025-199-XXX IDE interface test failed, cause unknown
3. Replace component under function test
No action
030-000-XXX SCSI interface Test Passed
030-00X-XXX 030-01X-XXX SCSI interface failure
1. SCSI signal cable
2. Check AC/DC power adapter
3. SCSI device
4. SCSI adapter card, if installed
5. System board
030-027-XXX SCSI interface Configuration/Setup error
1. SCSI signal cable
3. SCSI device
4. SCSI adapter card, if installed
5. System board
030-03X-XXX 030-04X-XXX SCSI interface error
1. SCSI signal cable
2. Check AC/DC power adapter
3. SCSI device
4. SCSI adapter card, if installed
5. System board
52 Hardware Maintenance Manual
Diagnostic Error Code
FRU/Action
030-195-XXX SCSI interface Test aborted by user
Information only Re-start the test, if necessary
1. Press F3 to review the log file
030-196-XXX SCSI interface test halt, error threshold
exceeded
2. Re-start the test to reset the log file
1. Make sure the component that is called out
page 39
030-197-XXX SCSI interface test warning
2. Re-run test
3. Replace the component that is called out in warning
statement
4. Replace the component under test
1. If a component is called out, make sure it is
page 39
030-198-XXX SCSI interface test aborted
030-199-XXX SCSI interface test failed, cause unknown
3. Replace component under function test
035-000-XXX RAID interface Test Passed
No action
035-0XX-XXX RAID interface Failure
1. RAID signal cable
2. RAID device
3. RAID adapter card, if installed
4. System board
035-195-XXX RAID interface Test aborted by user
Information only Re-start the test, if necessary
1. Press F3 to review the log file
035-196-XXX RAID interface test halt, error threshold
exceeded
2. Re-start the test to reset the log file
035-197-XXX RAID interface test warning
1. Make sure the component that is called out
page 39
2. Re-run test
3. Replace the component that is called out in warning
statement
4. Replace the component under test
035-198-XXX RAID interface test aborted
1. If a component is called out, make sure it is
page 39
Chapter 7. Symptom-to-FRU Index 53
Diagnostic Error Code
FRU/Action
035-199-XXX RAID interface test failed, cause unknown
3. Replace component under function test
No action
071-000-XXX Audio port Interface Test Passed
071-00X-XXX 071-01X-XXX 071-02X-XXXAudio port
1. Run Setup
error
3. System board
071-03X-XXX Audio port failure
1. Speakers
2. Microphone
3. Audio card, if installed
4. System board
071-04X-XXX Audio port failure
1. Run Setup
2. Audio card, if installed
3. System board
071-195-XXX Audio port Test aborted by user
Information only Re-start the test, if necessary
1. Press F3 to review the log file
071-196-XXX Audio port test halt, error threshold
exceeded
2. Re-start the test to reset the log file
071-197-XXX Audio port test warning
1. Make sure the component that is called out
page 39
2. Re-run test
3. Replace the component that is called out in warning
statement
4. Replace the component under test
071-198-XXX Audio port test aborted
1. If a component is called out, make sure it is
page 39
071-199-XXX Audio port test failed, cause unknown
3. Replace component under function test
071-25X-XXX Audio port failure
1. Speakers
2. Audio card, if installed
3. System board
No action
080-000-XXX Game Port interface Test Passed
1. Remove the game port device and re-test the
080-XXX-XXX Game Port interface Error
system
080-195-XXX Game Port interface Test aborted by user
Information only Re-start the test, if necessary
54 Hardware Maintenance Manual
Diagnostic Error Code
FRU/Action
1. Press F3 to review the log file
2. Re-start the test to reset the log file
080-196-XXX Game Port interface test halt, error
threshold exceeded
1. Make sure the component that is called out
page 39
080-197-XXX Game Port interface test warning
2. Re-run test
3. Replace the component that is called out in warning
statement
4. Replace the component under test
1. If a component is called out, make sure it is
page 39
080-198-XXX Game Port interface test aborted
080-199-XXX Game Port interface test failed, cause
unknown
3. Replace component under function test
086-000-XXX Mouse Port interface Test Passed
No action
086-001-XXX Mouse Port interface Presence
1. Mouse
2. System board
1. Mouse
086-032-XXX Mouse Port interface Device controller
failure
2. System board
1. Mouse
086-035-XXX Mouse Port interface Reset
2. System board
086-040-XXX Mouse Port interface IRQ failure
1. Run Setup
2. Mouse
3. System board
086-195-XXX Mouse Port interface Test aborted by user
Information only Re-start the test, if necessary
1. Press F3 to review the log file
086-196-XXX Mouse Port interface test halt, error
threshold exceeded
2. Re-start the test to reset the log file
086-197-XXX Mouse Port interface test warning
1. Make sure the component that is called out
page 39
2. Re-run test
3. Replace the component that is called out in warning
statement
4. Replace the component under test
Chapter 7. Symptom-to-FRU Index 55
Diagnostic Error Code
FRU/Action
086-198-XXX Mouse Port interface test aborted
1. If a component is called out, make sure it is
page 39
086-199-XXX Mouse Port interface test failed, cause
unknown
3. Replace component under function test
089-000-XXX Microprocessor Test Passed
No action
089-XXX-XXX Microprocessor failure
1. Microprocessor(s)
2. System board
089-195-XXX Microprocessor Test aborted by user
Information only Re-start the test, if necessary
1. Press F3 to review the log file
089-196-XXX Microprocessor test halt, error threshold
exceeded
2. Re-start the test to reset the log file
089-197-XXX Microprocessor test warning
1. Make sure the component that is called out
page 39
2. Re-run test
3. Replace the component that is called out in warning
statement
4. Replace the component under test
089-198-XXX Microprocessor test aborted
3. Replace component under function test
No action
170-000-XXX Voltage Sensor(s) Test Passed
1. Flash system
170-0XX-XXX Voltage Sensor(s) failure
2. System board
170-195-XXX Voltage Sensor(s) Test aborted by user
Information only Re-start the test, if necessary
1. Press F3 to review the log file
170-196-XXX Voltage Sensor(s) test halt, error threshold
exceeded
2. Re-start the test to reset the log file
56 Hardware Maintenance Manual
Diagnostic Error Code
FRU/Action
1. Make sure the component that is called out
page 39
170-197-XXX Voltage Sensor(s) test warning
2. Re-run test
3. Replace the component that is called out in warning
statement
4. Replace the component under test
1. If a component is called out, make sure it is
page 39
170-198-XXX Voltage Sensor(s) test aborted
170-199-XXX Voltage Sensor(s) test failed, cause
unknown
3. Replace component under function test
170-250-XXX 170-251-XXX Voltage Sensor(s) Voltage
1. AC/DC power adapter
limit error
2. System board
170-254-XXX Voltage Sensor(s) Voltage Regulator
Module error
1. Voltage Regulator Module (VRM)
2. Microprocessor
3. System board
No action
175-000-XXX Thermal Sensor(s) Test Passed
1. Flash system
175-0XX-XXX Thermal Sensor(s) failure
2. System board
175-195-XXX Thermal Sensor(s) Test aborted by user
Information only Re-start the test, if necessary
1. Press F3 to review the log file
175-196-XXX Thermal Sensor(s) test halt, error threshold
exceeded
2. Re-start the test to reset the log file
1. Make sure the component that is called out
page 39
175-197-XXX Thermal Sensor(s) test warning
2. Re-run test
3. Replace the component that is called out in warning
statement
4. Replace the component under test
1. If a component is called out, make sure it is
175-198-XXX Thermal Sensor(s) test aborted
connected and/or enabled
Chapter 7. Symptom-to-FRU Index 57
Diagnostic Error Code
FRU/Action
175-199-XXX Thermal Sensor(s) test failed, cause
unknown
3. Replace component under function test
175-250-XXX 175-251-XXX Thermal Sensor(s) limit error 1. Check fans
2. Check AC/DC power adapter voltages
3. Microprocessor
4. System board
No action
185-000-XXX Asset Security Test Passed
1. Flash system
185-XXX-XXX Asset Security failure
2. System board
185-278-XXX Asset Security Chassis Intrusion
1. Assure Asset Security Enabled
2. C2 Cover Switch
3. System board
No action
201-000-XXX System Memory Test Passed
1. Replace the memory module called out by the test
201-XXX-XXX System Memory error
2. System board
No action
202-000-XXX System Cache Test Passed
202-XXX-XXX System Cache error
1. Cache, if removable
2. System board
3. Microprocessor
No action
206-000-XXX Diskette Drive Test Passed
206-XXX-XXX Diskette Drive error
1. Diskette Drive Cable
2. Check AC/DC power adapter voltages
3. Diskette drive
4. System board
No action
215-000-XXX CD-ROM Drive Test Passed
215-XXX-XXX CD-ROM Drive error
1. CD-ROM Drive Cable
2. Check AC/DC power adapter voltages
3. CD-ROM drive
4. System board
217-000-XXX Hard Disk Drive Test Passed
No action
217-25X-XXX 217-26X-XXX Hard Disk Drive (IDE) error
1. Hard Disk Drive Cable
2. Check AC/DC power adapter voltages
3. Reseat the hard disk drive cable
4. Hard Disk drive (IDE)
5. System board
58 Hardware Maintenance Manual
Diagnostic Error Code
217-28X-XXX 217-29X-XXX Hard Disk Drive (SCSI) error 1. Hard Disk Drive Cable
2. Check AC/DC power adapter voltages
FRU/Action
3. Reseat the hard disk drive cable
4. Hard Disk drive (SCSI)
5. SCSI adapter card
6. System board
No action
220-000-XXX Hi-Capacity Cartridge Drive Test Passed
220-XXX-XXX Hi-Capacity Cartridge Drive error
1. Remove the Hi-Capacity Cartridge Drive and
re-test the system
301-XXX-XXX Keyboard error
1. Keyboard
2. Check and test mouse
3. System board
No action
301-000-XXX Keyboard Test Passed
302-000-XXX Mouse Test Passed
302-XXX-XXX Mouse error
No action
1. Mouse
2. Check and test Keyboard
3. System board
No action
303-000-XXX Joystick Test Passed
303-XXX-XXX Joystick error
Remove the Joystick and re-test the system
No action
305-000-XXX Monitor DDC Test Passed
305-250-XXX Monitor DDC self test failure
1. Run Setup to enable DDC
2. Cable
3. Monitor
4. Video card
5. System board
415-000-XXXModem Test Passed
No action
415-XXX-XXX Modem error
Remove the Modem and re-test the system
Beep symptoms
Beep symptoms are tones or a series of tones separated by pauses (intervals without sound) during POST.
The following tables describes beep symptoms.
Beep Symptom
1, 2, or 3 beeps
FRU/Action
Reseat the memory modules. If the error persists, replace
the memory modules one at a time until the failing module
is determined.
4, 5, 6, or 7 beeps9, 10, or 11 beeps
Before replacing the system board, remove any optional
adapters (Express card, Modem card, Media reader) and
retry. If the problem persists, replace the system board.
Otherwise, reinstall the optional adapters one at a time
until the failing adapter is determined.
8 beeps
Replace the system board.
Chapter 7. Symptom-to-FRU Index 59
POST error codes
Each time you power-on the system, it performs a series of tests that check the operation of the system
and some options. This series of tests is called the Power-On Self-Test, or POST. POST does the following
operations.
• Checks some basic system-board operations
• Checks the memory operation
• Starts the video operation
• Verifies that the boot drive is working
If the POST detects a problem, an error message appears on the screen. A single problem can cause several
error messages to appear. When you correct the cause of the first error message, the other error messages
probably will not appear on the screen the next time you turn on the system.
POST Error Message
Description/Action
CMOS battery failed
The CMOS battery is no longer functional.
Replace the battery.
CMOS checksum error - defaults loaded
Checksum of CMOS is incorrect.
The computer loads the default configuration settings.
This error might indicate that CMOS has become corrupt
due to a weak CMOS battery.
CPU at nnnn
nnnn is the running speed of the microprocessor.
Pressing Esc skips the full memory test
Press Esc to skip memory test
HARD DISK INSTALL FAILURE
Cannot find or initialize the hard disk drive controller or
the drive.
Make sure the hard disk drive is correctly installed.
If no hard disk drives are installed, make sure the hard
disk drive selection in Setup is set to NONE.
Keyboard error or no keyboard present
Cannot initialize the keyboard.
Make sure the keyboard is properly connected to the
computer and that no keys are held pressed during POST.
To purposely configure the computer without a keyboard,
set the error halt condition in Setup to HALT ON ALL, BUT
KEYBOARD. The BIOS then ignores the missing keyboard
during POST.
Memory Test:
This message displays during a full memory test, counting
down the memory areas being tested.
Memory test fail
If POST detects an error during memory testing, additional
information appears. This information gives specifics
about the type and location of the memory error.
60 Hardware Maintenance Manual
POST Error Message
Description/Action
Pressing the TAB key permits the user to toggle between
the default POST display screen and a custom POST
display screen.
Press TAB to show POST screen
Error: Non-System disk or disk error Replace and press
any key when ready
The BIOS was unable to find a suitable boot device.
Make sure the boot drive is properly connected to the
computer.
Make sure you have bootable media.
Miscellaneous error messages
Message/Symptom
FRU/Action
Changing display colors
Display/Monitor
1. Power Switch
page 31.
2. System Board
3. Riser card, if installed
1. Ensure that network is in startup sequence as first
Computer will not PXE from server
device or first device after diskette
2. Ensure that network adapter is enabled for PXE
3. Network adapter (Advise network administrator of new
MAC address)
Computer will not perform a Wake On LAN® (if applicable) 1. Check power supply and signal cable connections
to network adapter
2. Ensure that the operating system settings are set to
enable Wake on LAN®
3. Ensure Wake On LAN feature is enabled in
Setup/Configuration (see “Starting the Setup Utility
4. Ensure network administrator is using correct MAC
address
5. Ensure no interrupt or I/O address conflicts
6. Network adapter (advise network administrator of new
MAC address)
1. AC/DC Power Adapter
2. System Board
Diskette drive in-use light remains on or does not light
when drive is active.
1. Diskette Drive
2. System Board
3. Diskette Drive Cable
Flashing cursor with an otherwise blank display.
Incorrect memory size during POST
1. System Board
2. Primary Hard Disk Drive
3. Hard Disk Drive Cable
1. Run the Memory tests
2. Memory Module
3. System Board
Chapter 7. Symptom-to-FRU Index 61
Message/Symptom
FRU/Action
"Insert a Diskette" icon appears with a known-good
diagnostics diskette in the first 3.5-inch diskette drive.
1. System Board
2. Diskette Drive Cable
3. Network Adapter
1. Display
Intensity or color varies from left to right of characters
and color bars
2. Video adapter (if present)
3. System Board
No power or fan not running
1. Diskette Drive
Non-system disk or disk error-type message with a
known-good diagnostic diskette.
2. System Board
3. Diskette Drive Cable
1. Display
Other display symptoms not listed above (including blank
or illegible display)
2. System Board
Power-on indicator or hard disk drive in-use light not on,
but computer works correctly
1. Power switch/LED assembly
2. System Board
Printer problems
1. Printer
2. System Board
Program loads from the hard disk with a known-good
diagnostics diskette in the first 3.5-inch diskette drive
1. Run Setup and check Startup sequence.
2. Diskette Drive
3. Diskette Drive Cable
4. System Board
5. AC/DC power adapter
PXE computer cannot access programs from its own hard Replace the hard disk drive
disk.
PXE computer does not PXE from server
1. Check startup sequence
2. Check the network adapter LED status
1. Keyboard
Some or all keys on the keyboard do not work
2. Keyboard Cable
3. System Board
Undetermined problems
1. Turn off the computer.
2. Remove or disconnect the following components (if installed) one at a time.
a. External devices (modem, printer, or mouse)
b. Any adapters
c. Memory modules
d. Extended video memory
e. External Cache
f. External Cache RAM
g. Hard disk drive
h. Diskette drive
3. Turn on the power to re-test the system.
62 Hardware Maintenance Manual
4. Repeat steps 1 through 3 until you find the failing device or adapter.
If all devices and adapters have been removed, and the problem continues, replace the system board.
Chapter 7. Symptom-to-FRU Index 63
64 Hardware Maintenance Manual
Chapter 8. Replacing FRUs
This chapter provides step-by-step instructions for replacing major FRUs.
Important
guidelines will help you work safely.
FRU replacements are to be done by trained service technicians only.
Locations
This section provides illustrations to help locate the various connectors, controls, and components of the
computer.
Connectors on the front of the computer
Note: Not all computer models will have the following controls and connections.
1
2
3
4
5
USB connector
USB connector
Microphone connector
Headphone connector
Media card reader
© Copyright Lenovo 2005, 2010
65
Connectors on the rear of the computer
1
2
3
4
5
6
7
8
Microphone connector
USB connector
9
Ethernet connector
USB connectors (3)
10
11
12
13
Audio line in connector
Serial connector
Video graphics array (VGA) monitor connector
Digital video interface (DVI) monitor connector
Power adapter connector
RJ11 modem connector
ExpressCard (PCIe x 1) connector
Audio line out connector
Cable lock latch
Locating components
This section shows the location of the various components in the computer.
66 Hardware Maintenance Manual
8 Microprocessor
9 Heat sink
1 Front Audio/USB assembly
2 Hard disk drive
3 System fan assembly
4 Optical drive
10 Side cover
11 Memory modules
12 Internal speaker
13 Media Card Reader
5 AC/DC Power Adapter
6 Express Card assembly
Chapter 8. Replacing FRUs 67
7 System board
System board locations
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Microprocessor and heat sink
Modem daughter card (MDC) connector
Battery
ExpressCard USB connector
ExpressCard PCIe connector
Clear CMOS/Recovery jumper
Media card reader connector
Internal speaker connector
Front audio connector
Thermal sense cable connector
Memory connectors (2)
Serial (COM) connector
Front panel connector
Rear USB connector
Fan connector
Front USB connector
Internal power distribution connector
SATA IDE connectors (2)
Opening the cover
Important
68 Hardware Maintenance Manual
Turn off the computer and wait 3 to 5 minutes to let the computer cool before opening the computer
cover.
This section provides instructions on how to open the computer cover.
1. Remove any media (diskettes, CDs, or tapes) from the drives, shut down your operating system, and
turn off all attached devices and the computer.
2. Unplug all power cords from electrical outlets.
3. Disconnect the cables attached to the computer. This includes power cords, input/output (I/O) cables,
and any other cables that are connected to the computer. See “Connectors on the front of the computer”
4. Remove any locking devices, such as a cable lock that secures the computer cover.
5. Press the cover-release button on the side of the cover and pivot the computer cover outward.
6. If the computer cover is to be removed, disconnect all the cables from the system board.
Replacing the CMOS battery
This procedure describes how to remove and replace the CMOS battery.
If the CMOS battery fails, the date, time, and configuration information (including passwords) are lost. An
error message is displayed when you turn on the computer.
Important
Refer to “Safety notices (multi-lingual translations)” on page 6 for information about replacing and disposing
of the battery.
CAUTION:
When replacing the lithium battery, use only Part Number 33F8354 or an equivalent type battery
recommended by the manufacturer.
3. Remove the old battery.
Chapter 8. Replacing FRUs 69
4. Install the new battery.
page 81.
Note: When the computer is turned on for the first time after battery replacement, an error message
might be displayed. This is normal after replacing the battery.
6. Turn on the computer and all attached devices.
7. Use the Setup Utility program to set the date and time and any passwords. See Chapter 6 “Diagnostics,
Replacing the microprocessor
This section provides instructions on how to replace the microprocessor.
3. Remove the four screws securing the heat sink to the retention module on the system board and lift the
heat sink off the system board.
4. Disengage the microprocessor from the system board socket by pivoting the small handle upward until
it is in the vertical position.
5. Lift the microprocessor straight up and out of the socket.
70 Hardware Maintenance Manual
Notes:
a. Your microprocessor and socket might look different than the one illustrated.
b. Note the orientation of the microprocessor in the socket. Look for the small triangle on one corner of
the microprocessor. This is important when reinstalling the microprocessor on the system board.
c. Do not drop anything onto the microprocessor socket while it is exposed. The socket pins must be
kept as clean as possible.
6. When installing the microprocessor make sure that the small handle is in the vertical position.
7. Holding the new microprocessor 1 with your fingers, remove the protective cover 2 that protects
the microprocessor contacts.
8. Holding the microprocessor with your fingers, position the microprocessor so that the triangle 1 is
properly aligned with the socket.
9. Lower the microprocessor straight down into the socket.
Chapter 8. Replacing FRUs 71
Note: Install the black protective cover that was removed from the new microprocessor onto the
defective microprocessor after the installation is complete.
10.Secure the microprocessor in the socket by pivoting the small handle downward. Be sure to lock it
into position.
11.Position the heat sink on the retention module so that the four screws are aligned with the posts on the
system board. Tighten the four screws to secure the heat sink to the system board.
Replacing the system board
This section provides instructions on how to replace the system board.
2. Take note of the location of all cable connections on the system board and disconnect all cables. See
3. Remove the screws that secure the system board to the cover.
4. Lift the system board off of the cover.
5. Remove the memory modules from the failing system board and install them in the same location on
the new system board.
72 Hardware Maintenance Manual
6. If the system board has a modem daughter card installed, remove it from the failing system board and
7. Remove the heat sink and microprocessor from the failing system board and install them on the new
Note: You might have to install a new retention module on the new system board.
8. Position the new system board in the chassis so that the screw holes are aligned with the mounting studs.
9. Install and tighten the screws that secure the system board to the chassis.
Replacing a hard disk drive
This section provides instructions on how to replace the hard disk drive.
Important
When a new hard disk drive is installed, a set of Product Recovery discs might be required. The set of
Product Recovery discs enable the contents of the hard disk to be restored to the same state as when the
computer was originally shipped from the factory. For more information on recovering factory-installed
software, refer to "Recovering Software" in the User Guide.
To replace the hard disk drive:
2. Disconnect the power cable from the optical drive.
3. Place your finger on the tab located on the front of the hard disk drive and push upward. Then press
inward on the side tabs and pivot the hard disk drive upward to remove.
4. Remove the failing hard disk drive from the chassis.
5. Disconnect the signal and power cables from the hard disk drive.
6. Remove the hard disk drive from the plastic bracket by flexing the sides of the bracket enough to slide
it free of the hard disk drive.
7. To install the new hard disk drive into the plastic bracket 1 , flex the bracket and align the pins on the
bracket with the holes in the hard disk drive. Do not touch the circuit board 2 on the bottom of the
hard disk drive.
Chapter 8. Replacing FRUs 73
8. Connect the signal and power cables to the rear of the new hard disk drive.
9. Slide the new hard disk drive into the drive bay until it snaps into position.
10.Reconnect the power cable to the optical drive.
Replacing an optical drive
This section provides instructions on how to replace an optical drive.
2. Remove the front bezel by releasing the two tabs and pivoting the bezel forward to remove completely.
3. Disconnect the signal and power cables from the rear of the optical drive.
4. Press the blue release button and remove the optical drive out the front of the computer.
74 Hardware Maintenance Manual
5. Remove the retainer bracket from the failing drive and install it on the new optical drive.
6. Slide the new optical drive into the drive bay until it snaps into position.
7. Connect the signal and power cables to the drive.
8. Replace the front bezel.
Replacing a memory module
This section provides instructions on how to replace a memory module.
3. Remove the memory module being replaced by opening the retaining clips as shown.
Chapter 8. Replacing FRUs 75
4. Insert the notched end 2 of the memory module into the socket 1 . Press the memory module firmly,
and pivot the memory module until it snaps into place. Make sure that the memory module is firmly
fixed in the connector and does not move easily.
Replacing the modem
This section provides instructions on how to replace the modem.
connected to the MDC connector.
76 Hardware Maintenance Manual
3. Remove the two screws that secure the modem card to the system board.
4. Disconnect the modem card from the system board.
5. Disconnect the RJ11 modem cable from the modem card.
6. Connect the RJ11 modem cable to the new modem card.
7. Install the new modem card to the MDC connector on the system board by aligning the holes in the
modem card with the pins in the system board.
8. Install the two screws to secure the modem card to the system board.
Replacing the Express card assembly
This section provides instructions on how to replace the Express card assembly.
Chapter 8. Replacing FRUs 77
3. Disconnect the cable connected to the Express card.
4. Remove the four screws that secure the Express card assembly to the Chassis.
5. Remove the Express card assembly from the system board.
6. Install the new Express card assembly into the chassis by aligning the holes in the Express card assembly
with the pins in the chassis.
7. Install the four screws to secure the Express card assembly to the chassis.
8. Reconnect the cable to the Express card assembly.
Replacing the Media Card Reader
This section provides instructions on how to replace the Media Card Reader.
3. Disconnect the Media Card Reader cable connected to the system board. See “System board locations”
on page 68
4. Remove the screw that secures the Media Card Reader to the Chassis.
78 Hardware Maintenance Manual
5. Remove the Media Card Reader from the chassis.
6. Install the new Media Card Reader into the chassis and align the screw-hole in the Media Card Reader
with the hole in the chassis.
7. Install the screw to secure the Media Card Reader to the chassis.
8. Connect the Media Card Reader cable to the system board.
Replacing the system fan assembly
This section provides instructions on how to replace the system fan assembly.
Note: When you receive your new system fan assembly, you will receive new rubber mounts.
on page 68.
5. Remove the two rubber mounts from the system fan assembly that connect to the chassis by breaking
them or cutting them with a pair of scissors. Once this has been done, remove the rubber mounts
from the rear of the chassis.
6. Pull the system fan assembly outward from the chassis. Then lift the system fan assembly out of the
chassis.
Chapter 8. Replacing FRUs 79
7. When installing your new system fan assembly, use the new rubber mounts that come with the new
system fan.
8. Install the two short rubber mounts in the new system fan assembly as shown.
9. Install the two long rubber mounts into the rear of the chassis as shown. Push the mounts through the
holes of the chassis. If necessary, pull the mounts through the holes from inside the chassis.
10.To install the new system fan assembly into the chassis, align the open holes in the system fan assembly
with the long rubber mounts in the chassis. Pull the rubber mounts through the holes in the system fan
assembly until the system fan is in place.
11.Once the system fan assembly is secure, you should remove the extra rubber for the mounts.
12.Connect the system fan assembly cable to the system fan connector on the system board.
13.Replace the hard disk drive, if it was removed.
80 Hardware Maintenance Manual
Completing the FRU replacement
After replacing the parts, you need to close the cover and reconnect cables, including telephone lines and
power cords. Also, depending on the part that was replaced, you might need to confirm the updated
information in the Setup Utility program. See Chapter 6 “Diagnostics, Test and Recovery Information”
on page 39.
This section provides instructions on how to complete the parts replacement.
1. Ensure that all components have been reassembled correctly and that no tools or loose screws are left
2. Make sure that the cables are routed correctly before closing the computer cover.
Important: Correctly route all power supply cables to avoid interference when closing the computer
cover. Keep cables clear of the hinges and sides of the computer chassis.
3. Position the computer cover on the chassis so that the rail guide on the bottom of the cover engages the
rail. Then, push the computer cover closed until it snaps into position.
Chapter 8. Replacing FRUs 81
4. If a cover lock is installed, lock the cover.
5. Reconnect the external cables and power cords to the computer. See “Connectors on the rear of the
6. To update your configuration, see Chapter 6 “Diagnostics, Test and Recovery Information” on page 39.
82 Hardware Maintenance Manual
Chapter 9. FRU lists
Attention: Read “Important information about replacing RoHS compliant FRUs” on page 1 before replacing
any FRUs.
Note: In the following tables, a CRU (Customer Replaceable Unit) is identified as either "1", "2", or "N" in the
CRU column. "N" means that the part is not a CRU, "1" means that the part is a Self-service CRU, and "2"
means that the part is an Optional-service CRU.
Machine Type 6393
Item
#
1
2
2
6393 FRUs
FRU#
CRU
41R8510
40Y9034
40Y9035
N
2
2
Front audio/USB card and cable (included in Cables kit 41R8510) (all models)
Hard disk drive, 80 GB 7200rpm SATA (models 12Q 14C 14V 11S 11D 11Y)
Hard disk drive, 160 GB 7200rpm SATA (models 15S 15D 15Y 15Q 15C 16Q 17S
17Y 18S 18Y)
2
2
2
2
40Y9036
87H4891
41X5582
43C3671
2
2
2
2
Hard disk drive, 25 GB 7200rpm SATA (models 13B 13H)
Hard disk drive, 320 GB 7200rpm SATA (models)
Hard disk drive, 500 GB 7200rpm SATA (models)
Hard disk drive, 750 GB 7200rpm SATA (models)
© Copyright Lenovo 2005, 2010
83
Item
#
6393 FRUs
Hard disk drive, 1TB 7200rpm SATA (models CTO)
System fan (all models)
FRU#
CRU
2
3
4
2
2
2
45C5973
41R8511
41N3325
DVD-ROM Drive - 16x/48x - SATA (models 12Q 14C 14V 11S 11D 11Y 15S 15D 15Y
15Q 15C 16Q 17S 17Y)
4
4
2
2
DVD-ROM Drive - DVD-RW/CD-RW Rambo 8 (SATA) Matrix (models)
43C1042
42Y9353
DVD-ROM Drive - DVD-ROM/CD-RW Combo Drive - 48x/32x/48x/16x - SATA Matrix
(models 13B 13H 18S 18Y)
5
5
41A9732
41A9747
1
1
Power Adapter, 120W AC/DC (models 12Q 14C 14V 11S 11D 11Y 13B 13H 15S 15D
15Y 15Q 15C 16Q 17S 17Y 18S 18Y)
Power Adapter, 120W power adapter (models 12Q 14C 14V 11S 11D 11Y 13B 13H
15S 15D 15Y 15Q 15C 16Q 17S 17Y 18S 18Y)
6
7
7
41R8570
46R3849
46R3848
N
N
N
Express Card Assembly (all models)
System board, Mini-ITX Intel (Q35, ICH9DO) (models)
System board, non-AMT Mini-ITX Intel (Q35, ICH9DO) (models 12Q 14C 14V 11S 11D
11Y 13B 13H 15S 15D 15Y 15Q 15C 16Q 17S 17Y 18S 18Y)
8
8
8
8
8
8
8
N
N
N
N
N
N
N
Microprocessor, Intel Conroe E6750 (Core2 Duo) 2.66GHz, G-0 Stepping, 65nm,
1333MHZ FSB, 4MB L2 (models)
45C6898
45C6899
45C6900
45C6901
45C6902
45C8499
45C8531
Microprocessor, Intel Conroe E6550 (Core2 Duo) 2.33GHz, G-0 Stepping, 65nm,
1333MHz FSB, 4MB L2 (models)
Microprocessor, Intel Conroe E4500 (Core2 Duo) 2.20GHz, M-0 Stepping, 65nm,
800MHz FSB, 2MB L2 (models 15S 15D 15Y 15Q 15C)
Microprocessor, Intel Conroe E2160 (Pentium D) 1.8GHz, M-0 Stepping, 65nm,
800MHz FSB, 1MB L2 (models 14C 14V)
Microprocessor, Intel Conroe-L 440 (Celeron) 2.0GHz, A-1 Stepping, 65nm, 800MHz
FSB, 512KB L2 (models 11S 11D 11Y 12Q 13B 13H)
Microprocessor, Intel Wolfdale E8400 (Core2 Duo) 3.0GHz, C-0 Stepping, 45nm,
1333MHz FSB, 6MB L2 (models)
Microprocessor, Intel Wolfdale E8200 (Core2 Duo) 2.66GHz, C-0 Stepping, 45nm,
1333MHz FSB, 6MB L2 (models)
8
8
46R4261
46R4260
41R8545
41R8563
43C3814
N
N
2
Microprocessor, E7200, 2.53GHz, 1066MHz FSB, 3MB L2 (models 18S 18Y)
Microprocessor, E2200, 2.20GHz, 800MHz FSB, 1MB L2 (models 16Q 17S 17Y)
Heat sink Intel (all models)
9
10
11
N
2
Kit, Shell (all models)
Memory module, 512MB DDR2 PC2-5300 (667MHz) SoDIMM (models 12Q 14C 14V
17S 17Y)
11
2
Memory module, 1GB DDR2 PC2-5300 (667MHz) SoDIMM (models 11S 11D 11Y 13B
13H 15S 15D 15Y 15Q 15C 16Q 18S 18Y)
43C3815
11
12
13
2
2
Memory module, 2GB DDR2 PC2-5300 (667MHz) SoDIMM (models)
Internal speaker (all models)
43C6489
41R8517
41R8568
N
Media card reader (all models)
The FRUs listed in the following tables are not illustrated.
84 Hardware Maintenance Manual
6393 FRUs
FRU#
CRU
2
41R8518
41R8543
41R8544
41R8548
41R8560
41R8555
Hard Disk Drive tray (all models)
Shield Kit (all models)
N
N
Cable, C2 Swtich/Housing assembly (all models)
Cable, Serial (all models)
N
N
USB Cable (all models)
N
PWR/LED Cable Assembly (all models)
6393 Keyboards (USB Preferred Pro)
FRU#
CRU
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
41A5289
41A5290
41A5291
41A5292
41A5293
41A5294
41A5295
41A5296
41A5297
41A5298
41A5299
41A5300
41A5301
41A5302
41A5303
41A5304
41A5305
41A5306
41A5307
41A5308
41A5309
41A5310
41A5311
41A5312
41A5313
41A5314
41A5315
41A5316
41A5317
41A5318
41A5319
US English (models 12Q 15Q 16Q)
Arabic(models)
Arabic/French (models)
Belgian/French (models)
Belgian/UK (models)
Brazilian (models)
Bulgarian (models)
Hong Kong/Taiwan (models)
Czech (models)
Danish (models)
Dutch (models)
French (models)
French Canadian 445 (models)
French Canadian 58 (models)
German (models)
Greek (models)
Greek/US (models)
Hebrew (models)
Hungarian (models)
Iceland (models)
Italian (models)
Japanese (models)
Korean (models)
LA Spanish (models)
Norwegian (models)
Polish (models)
Portuguese (models)
Romanian 446 (models)
Romanian 096 (models)
Russian/Cyrillic(models)
Serbian/Cyrillic (models)
Chapter 9. FRU lists 85
6393 Keyboards (USB Preferred Pro)
FRU#
CRU
41A5320
41A5321
41A5322
41A5323
41A5324
41A5325
41A5326
41A5327
41A5328
41A5329
1
1
1
1
1
1
1
1
1
1
Slovak (models)
Spanish (models 11S 11D 11Y 15S 15D 15Y 17S 17Y 18S 18Y)
Swedish/Finn (models)
Swiss (models)
Thailand (models)
Turkish 440 (models)
Turkish 179 (models)
UK English (models)
US Euro (models)
Slovenian (models)
6393 Keyboard (USB Preferred Pro Fingerprint Keyboard)
US (models)
FRU#
CRU
1
41A5248
41A5249
41A5250
41A5251
41A5252
41A5253
41A5254
41A5255
41A5256
41A5257
41A5258
41A5259
41A5260
41A5261
41A5262
41A5263
41A5264
41A5265
41A5266
41A5267
41A5268
41A5269
41A5270
41A5271
41A5272
41A5273
41A5274
1
Arabic (models)
1
Arabic/French (models)
Belgian/French (models)
Belgian/UK (models)
Brazil/Portuguese (models)
Bulgarian (models)
1
1
1
1
1
Chinese/US (models)
Czech (models)
1
1
Danish (models)
1
Dutch (models)
1
French (models)
1
French Canadian 445 (models)
French Canadian 58 (models)
German (models)
1
1
1
Greek (models)
1
Greek/US (models)
1
Hebrew (models)
1
Hungarian (models)
Iceland (models)
1
1
Italian (models)
1
Japanese (models)
1
Korean (models)
LA Spanish (models)
Norwegian (models)
Polish (models)
1
1
1
Portugese (models)
86 Hardware Maintenance Manual
6393 Keyboard (USB Preferred Pro Fingerprint Keyboard)
Romanian 446 (models)
FRU#
CRU
1
41A5276
41A5275
41A5277
41A5278
41A5279
41A5280
41A5281
41A5282
41A5283
41A5284
41A5285
41A5286
41A5287
41A5288
1
Romanian 96 (models)
Russian/Cyrilic (models)
Serbian/Cyrilic (models)
Slovak (models)
1
1
1
1
Spanish (models)
1
Swedish/Finn (models)
Swiss, F/G (models)
Thailand (models)
1
1
1
Turkish 179 (models)
Turkish 440 (models)
UK (models)
1
1
1
US Euro(models)
1
Slovenian (models)
6393 mice
FRU#
CRU
41U3013
1
Optical Wheel Mouse (400DPI, USB) (models 12Q 14C 14V 11S 11D 11Y 13B 13H 15S 15D
15Y 15Q 15C 16Q 17S 17Y 18S 18Y)
41U3030
41U3019
1
1
Optical Wheel Mouse (400DPI, USB) (models 12Q 14C 14V 11S 11D 11Y 13B 13H 15S 15D
15Y 15Q 15C 16Q 17S 17Y 18S 18Y)
ScrollPoint Optical Mouse (800DPI, USB) (models )
6393 Adapters and miscellaneous FRUs
Modem Daughter Card (MDC 1.5) Kit (models)
FRU#
CRU
39T0495
41R8522
41A5331
41A5334
89P8571
91P8835
41R4770
2
2
1
1
1
N
2
Modem Daughter Card (MDC 1.5) Kit Internal cable/RJ11 (models)
Lenovo Branded speakers - 2 piece--primary (models)
Lenovo Branded speakers - 2 piece--secondary (models)
Speaker power brick (models)
Thermal Grease Syringe (models)
Vertical PC stand (VPC) for Blue 4.5L chassis (models)
6393 Power Cords
Power cord - US/Canada (models 11S 11D 15S 15D 18S 17S)
Power cord - Japan (models)
FRU#
CRU
42T5004
42T5011
42T5017
42T5174
42T5029
42T5035
42T5041
42T5044
1
1
1
1
1
1
1
1
Power cord - Argentina (models 11Y 15Y 17Y 18Y)
Power cord - Brazil (models)
Power cord - Europe (Germany) (models)
Power cord - UK (models)
Power cord - Denmark (models)
Power cord - Switzerland (models)
Chapter 9. FRU lists 87
6393 Power Cords
FRU#
CRU
1
42T5047
42T5050
42T5056
42T5062
42T5065
42T5071
42T5077
42T5083
42T4406
42T5089
42T5096
42T5102
42T5177
42T5114
42T5120
42T5126
42T5129
42T5132
42T5135
42T5141
42T5147
42T5150
42T5156
42T5162
42T5168
42T4400
Power cord - Italy (models)
1
Power cord - Australia / New Zealand (models)
1
Power cord - South Africa (models)
1
Power cord - Israel (models)
1
Power cord - China (PRC) (models 14C 15C)
1
Power cord - Taiwan (models)
1
Power cord - Korea (models)
1
Power cord - India (models 12Q 15Q 16Q)
1
Power cord - Thailand (models)
1
Power cord - US/Canada--optional second source (models 11S 11D 15S 15D 18S 17S)
Power cord - Japan-optional second source (models)
Power cord - Argentina -optional second source (models 11Y 15Y 17Y 18Y)
Power cord - Brazil (new type) -optional second source (models)
Power cord - Europe (Germany) -optional second source (models)
Power cord - UK -optional second source (models)
Power cord - Denmark -optional second source (models)
Power cord - Switzerland -optional second source (models)
Power cord - Italy -optional second source (models)
Power cord - Australia/New Zealand -optional second source (models)
Power cord - South Africa -optional second source (models)
Power cord - Israel -optional second source (models)
Power cord - China (PRC) -optional second source (models 14C 15C)
Power cord - Taiwan-optional second source (models)
Power cord - Korea-optional second source (models)
Power cord - India-optional second source (models 12Q 15Q 16Q)
Power cord - Thailand-optional second source (models)
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
6393 Windows XP Home Recovery CDs
FRU#
CRU
45R6005
45R6006
45R6007
45R6010
45R6009
45R6008
45R6014
45R6015
45R6020
45R6013
45R6018
1
1
1
1
1
1
1
1
1
1
1
US/UK/AP/TH (models)
FR/CF (models)
GR (models)
IT (models)
BR (models)
SP/LA (models)
DK (models)
NL (models)
AE (models)
SV (models)
HE (models)
88 Hardware Maintenance Manual
6393 Windows XP Home Recovery CDs
FRU#
CRU
1
45R6017
45R6012
45R6019
45R6030
45R6021
45R6029
45R6023
45R6016
45R6022
45R6024
45R6011
45R6025
45R6026
45R6027
45R6028
FI (models)
1
NO (models)
PL (models)
PO (models)
RU (models)
RE (models)
HU (models)
CZ (models)
TR (models)
GK (models)
Japanese (models)
1
1
1
1
1
1
1
1
1
1
Simplified Chinese (models)
Taiwan-TC (models)
1
1
Hong Kong-TC (models)
Korea (models)
1
6393 Windows XP Pro Recovery CDs
FRU#
CRU
1
45R5979
45R5980
45R5981
45R5984
45R5983
45R5982
45R5988
45R5989
45R5994
45R5987
45R5992
45R5991
45R5986
45R5993
45R6004
45R5995
45R6003
45R5997
45R5990
45R5996
45R5998
45R5985
US/UK/AP/TH (models)
FR/CF (models)
GR (models)
1
1
1
IT (models)
1
BR (models)
1
SP/LA (models)
DK (models)
1
1
NL (models)
1
AE (models)
1
SV (Swedish) (models)
HE (models)
1
1
FI (models)
1
NO (models)
PL (models)
1
1
PO (models)
1
RU (models)
1
RE (models)
1
HU (models)
1
CZ (models)
1
TR (models)
1
GK (models)
1
Japanese (models)
Chapter 9. FRU lists 89
6393 Windows XP Pro Recovery CDs
FRU#
CRU
45R5999
45R6000
45R6001
45R6002
45R5977
45R5978
1
1
1
1
1
1
Simplified Chinese (models)
Taiwan-TC (models)
Hong Kong-TC (models)
Korea (models)
Multilingual 1 XP-P -- EN, NL, FR, GR, IT (models)
Multilingual 2 XP-P -- EN, DK, FI, NO, SV (models)
6393 Vista Home Basic 32 Recovery DVDs
FRU#
CRU
1
46R7098
46R7099
46R7100
46R7101
46R7102
46R7103
46R7104
46R7105
46R7106
46R1086
46R7107
46R1088
46R1089
46R1090
46R1091
46R7108
46R1093
46R1094
46R1095
46R7109
46R7110
46R7111
46R1099
46R1100
46R1101
46R1102
46R1103
46R1104
English (models 13H)
Russian English (models)
French (models)
1
1
1
German (models)
Spanish (models)
Brazilian (models)
Italian (models)
1
1
1
1
Japanese (models)
Norwegian (models)
Swedish (models)
Danish (models)
1
1
1
1
Dutch (models)
1
Czech (models)
1
Finnish (models)
1
Polish (models)
1
Russian (models)
Turkish (models)
1
1
Hungarian (models)
Greek (models)
1
1
Simplified Chinese (models)
Taiwan (models)
1
1
HongKong (models)
Korea (models)
1
1
Slovenian (models)
Hebrew (models)
Portuguese (models)
Arabic Localized (models)
Slovakia (models)
1
1
1
1
90 Hardware Maintenance Manual
6393 Vista Business 32 Recovery DVDs
FRU#
CRU
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
46R7070
46R7071
46R7072
46R7073
46R7074
46R7075
46R7076
46R7077
46R7078
46R1028
46R7079
46R1030
46R1031
46R1032
46R1033
46R7080
46R1035
46R1036
46R1037
46R7081
46R7082
46R7083
46R1041
46R1042
46R1043
46R1044
46R1045
46R1046
46R1047
46R1048
English (models 15Q)
Russian (models)
French (models)
German (models)
Spanish (models 15S 15D 15Y 17S 17Y 18S 18Y)
Brazilian (models)
Italian (models)
Japanese (models)
Norwegian (models)
Swedish (models)
Danish (models)
Dutch (models)
Czech (models)
Finnish (models)
Polish (models)
Russian (models)
Turkish (models)
Hungarian (models)
Greek (models)
Simplified Chinese (models 15C)
Trad Chinese (models)
Trad Chinese (models)
Korean (models)
Slovenian (models)
Romanian (models)
Portuguese (models)
Serbian - Latin (models)
Slovakian (models)
Arabic Localized (models)
Hebrew (models)
6393 Vista Ultimate 32 Recovery DVDs
FRU#
CRU
46R7112
46R7113
46R7114
46R7115
46R7116
46R7117
46R7118
1
1
1
1
1
1
1
English (models)
Russian (models)
French (models)
German (models)
Spanish (models)
Brazilian (models)
Italian (models)
Chapter 9. FRU lists 91
6393 Vista Ultimate 32 Recovery DVDs
FRU#
CRU
1
46R7119
46R7120
46R1114
46R7121
46R1116
46R1117
46R1118
46R1119
46R7122
46R1121
46R1122
46R1123
46R7123
46R7124
46R7125
46R1127
46R1128
46R1129
46R1130
46R1131
46R1132
Japanese (models)
Norwegian (models)
Swedish (models)
Danish (models)
Dutch (models)
1
1
1
1
1
Czech (models)
Finnish (models)
Polish (models)
1
1
1
Russian (models)
Turkish (models)
Hungarian (models)
Greek (models)
1
1
1
1
Simplified Chinese (models)
Traditional Chinese (models)
Traditional Chinese (models)
Korean (models)
1
1
1
1
Slovenian (models)
1
Hebrew (models)
1
Portuguese (models)
Slovakian (models)
1
1
Arabic Localized (models)
6393 Vista Business 64 Recovery DVDs
FRU#
CRU
1
46R7084
46R7085
46R7086
46R7087
46R7088
46R7089
46R7090
46R7091
46R7092
46R1058
46R7093
46R1060
46R1061
46R1062
46R1063
46R7094
English (models)
Russian English (models)
French (models)
German (models)
Spanish (models)
Brazilian (models)
Italian (models)
1
1
1
1
1
1
1
Japanese (models)
Norwegian (models)
Swedish (models)
Danish (models)
Dutch (models)
1
1
1
1
1
Czech (models)
1
Finnish (models)
Polish (models)
1
1
Russian (models)
92 Hardware Maintenance Manual
6393 Vista Business 64 Recovery DVDs
FRU#
CRU
1
46R1065
46R1066
46R1067
46R7095
46R7096
46R7097
46R1071
46R1072
46R1073
46R1074
46R1075
46R1076
Turkish (models)
Hungarian (models)
Greek (models)
1
1
1
Simplified Chinese (models)
Taiwan (models)
1
1
Hong Kong (models)
Korea (models)
1
1
Slovenian (models)
Arabic Localized (models)
Hebrew (models)
1
1
1
Portuguese (models)
Slovakian (models)
1
Machine Type 6394
Chapter 9. FRU lists 93
Item
#
6394 FRUs
Front audio/USB card and cable (included in Cables kit 41R8510) ( models)
Hard disk drive, 80 GB 7200rpm SATA (models)
Hard disk drive, 160 GB 7200rpm SATA (models)
Hard disk drive, 25 GB 7200rpm SATA (models)
Hard disk drive, 320 GB 7200rpm SATA (models)
Hard disk drive, 500 GB 7200rpm SATA (models)
Hard disk drive, 750 GB 7200rpm SATA (models)
Hard disk drive, 1TB 7200rpm SATA (models CTO)
System fan (models)
FRU#
CRU
N
2
1
2
2
2
2
2
2
2
3
4
4
4
41R8510
40Y9034
40Y9035
40Y9036
87H4891
41X5582
43C3671
45C5973
41R8511
41N3325
43C1042
42Y9353
2
2
2
2
2
2
2
2
DVD-ROM Drive - 16x/48x - SATA (models)
2
DVD-ROM Drive - DVD-RW/CD-RW Rambo 8 (SATA) Matrix (models)
2
DVD-ROM Drive - DVD-ROM/CD-RW Combo Drive - 48x/32x/48x/16x - SATA Matrix
(models)
5
5
6
7
7
8
41A9732
41A9747
41R8570
46R3849
46R3848
45C6898
1
1
Power Adapter, 120W AC/DC (models)
Power Adapter, 120W power adapter (models)
Express Card Assembly (models)
N
N
N
N
System board, Mini-ITX Intel (Q35, ICH9DO) (models)
System board, non-AMT Mini-ITX Intel (Q35, ICH9DO) (models)
Microprocessor, Intel Conroe E6750 (Core2 Duo) 2.66GHz, G-0 Stepping, 65nm,
1333MHZ FSB, 4MB L2 (models)
8
8
8
8
8
8
N
N
N
N
N
N
Microprocessor, Intel Conroe E6550 (Core2 Duo) 2.33GHz, G-0 Stepping, 65nm,
1333MHz FSB, 4MB L2 (models)
45C6899
45C6900
45C6901
45C6902
45C8499
45C8531
Microprocessor, Intel Conroe E4500 (Core2 Duo) 2.20GHz, M-0 Stepping, 65nm,
800MHz FSB, 2MB L2 (models)
Microprocessor, Intel Conroe E2160 (Pentium D) 1.8GHz, M-0 Stepping, 65nm,
800MHz FSB, 1MB L2 (models)
Microprocessor, Intel Conroe-L 440 (Celeron) 2.0GHz, A-1 Stepping, 65nm, 800MHz
FSB, 512KB L2 (models)
Microprocessor, Intel Wolfdale E8400 (Core2 Duo) 3.0GHz, C-0 Stepping, 45nm,
1333MHz FSB, 6MB L2 (models)
Microprocessor, Intel Wolfdale E8200 (Core2 Duo) 2.66GHz, C-0 Stepping, 45nm,
1333MHz FSB, 6MB L2 (models)
8
46R4261
46R4260
41R8545
41R8563
43C3814
43C3815
43C6489
41R8517
41R8568
N
N
2
Microprocessor, E7200, 2.53GHz, 1066MHz FSB, 3MB L2 (models)
Microprocessor, E2200, 2.20GHz, 800MHz FSB, 1MB L2 (models)
Heat sink Intel (models)
8
9
10
11
11
11
12
13
N
2
Kit, shell (models)
Memory module, 512MB DDR2 PC2-5300 (667MHz) SoDIMM (models)
Memory module, 1GB DDR2 PC2-5300 (667MHz) SoDIMM (models)
Memory module, 2GB DDR2 PC2-5300 (667MHz) SoDIMM (models)
Internal speaker (models)
2
2
2
N
Media card reader (models)
94 Hardware Maintenance Manual
The FRUs listed in the following tables are not illustrated.
6394 FRUs
Hard disk drive tray (models)
FRU#
CRU
2
41R8518
41R8543
41R8544
41R8548
41R8560
41R8555
N
Shield Kit (all models)
N
Cable, C2 Swtich/Housing assembly (models)
Cable, Serial (models)
N
N
USB cable (models)
N
PWR/LED cable assembly (models)
6394 Keyboards (USB Preferred Pro)
US English (models)
Arabic (models)
FRU#
CRU
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
41A5289
41A5290
41A5291
41A5292
41A5293
41A5294
41A5295
41A5296
41A5297
41A5298
41A5299
41A5300
41A5301
41A5302
41A5303
41A5304
41A5305
41A5306
41A5307
41A5308
41A5309
41A5310
41A5311
41A5312
41A5313
41A5314
41A5315
41A5316
41A5317
41A5318
Arabic/French (models)
Belgian/French (models)
Belgian/UK (models)
Brazilian (models)
Bulgarian (models)
Hong Kong/Taiwan (models)
Czech (models)
Danish (models)
Dutch (models)
French (models)
French Canadian 445 (models)
French Canadian 58 (models)
German (models)
Greek (models)
Greek/US (models)
Hebrew (models)
Hungarian (models)
Iceland (models)
Italian (models)
Japanese (models)
Korean (models)
LA Spanish (models)
Norwegian (models)
Polish (models)
Portuguese (models)
Romanian 446 (models)
Romanian 096 (models)
Russian/Cyrillic (models)
Chapter 9. FRU lists 95
6394 Keyboards (USB Preferred Pro)
FRU#
CRU
41A5319
41A5320
41A5321
41A5322
41A5323
41A5324
41A5325
41A5326
41A5327
41A5328
41A5329
1
1
1
1
1
1
1
1
1
1
1
Serbian/Cyrillic (models)
Slovak (models)
Spanish (models )
Swedish/Finn (models)
Swiss (models)
Thailand (models)
Turkish 440 (models)
Turkish 179 (models)
UK English (models)
US European (models)
Slovenian (models)
6394 Keyboard (USB Preferred Pro Fingerprint Keyboard)
FRU#
CRU
1
41A5248
41A5249
41A5250
41A5251
41A5252
41A5253
41A5254
41A5255
41A5256
41A5257
41A5258
41A5259
41A5260
41A5261
41A5262
41A5263
41A5264
41A5265
41A5266
41A5267
41A5268
41A5269
41A5270
41A5271
41A5272
41A5273
US (models)
1
Arabic (models)
1
Arabic/French (models)
Belgian/French (models)
Belgian/UK (models)
Brazil/Portuguese (models)
Bulgarian (models)
Chinese/US (models)
Czech (models)
1
1
1
1
1
1
1
Danish (models)
1
Dutch (models)
1
French (models)
1
French Canadian 445 (models)
French Canadian 58 (models)
German (models)
1
1
1
Greek (models)
1
Greek/US (models)
Hebrew (models)
1
1
Hungarian (models)
Iceland (models)
1
1
Italian (models)
1
Japanese (models)
Korean (models)
1
LA Spanish (models)
Norwegian (models)
Polish (models)
1
1
96 Hardware Maintenance Manual
6394 Keyboard (USB Preferred Pro Fingerprint Keyboard)
Portuguese (models)
FRU#
CRU
1
41A5274
41A5276
41A5275
41A5277
41A5278
41A5279
41A5280
41A5281
41A5282
41A5283
41A5284
41A5285
41A5286
41A5287
41A5288
1
Romanian 446 (models)
Romanian 96 (models)
Russian/Cyrillic (models)
Serbian/Cyrillic (models)
Slovak (models)
1
1
1
1
1
Spanish (models)
1
Swedish/Finn (models)
Swiss, F/G (models)
Thailand (models)
1
1
1
Turkish 179 (models)
Turkish 440 (models)
UK (models)
1
1
1
US European (models)
Slovenian (models)
1
6394 mice
FRU#
CRU
41U3013
41U3030
41U3019
1
1
1
Optical wheel mouse (400DPI, USB) (models)
Optical wheel mouse (400DPI, USB) (models)
Scroll point optical mouse (800DPI, USB) (models)
6394 Adapters and miscellaneous FRUs
FRU#
CRU
39T0495
41R8522
41A5331
41A5334
89P8571
91P8835
41R4770
2
2
1
1
1
N
2
Modem daughter card (MDC 1.5) kit (models)
Modem daughter card (MDC 1.5) kit internal cable /RJ11 (models)
Lenovo branded speakers - 2 piece--primary (models)
Lenovo branded speakers - 2 piece--secondary (models)
Speaker power brick (models)
Thermal grease syringe (models)
Vertical PC stand (VPC) for blue 4.5L chassis (models)
6394 Power Cords
Power cord - US/Canada (models)
Power cord - Japan (models)
FRU#
CRU
42T5004
42T5011
42T5017
42T5174
42T5029
42T5035
42T5041
42T5044
1
1
1
1
1
1
1
1
Power cord - Argentina (models)
Power cord - Brazil (models)
Power cord - Europe (Germany) (models)
Power cord - UK (models)
Power cord - Denmark (models)
Power cord - Switzerland (models)
Chapter 9. FRU lists 97
6394 Power Cords
FRU#
CRU
1
42T5047
42T5050
42T5056
42T5062
42T5065
42T5071
42T5077
42T5083
42T4406
42T5089
42T5096
42T5102
42T5177
42T5114
42T5120
42T5126
42T5129
42T5132
42T5135
42T5141
42T5147
42T5150
42T5156
42T5162
42T5168
42T4400
Power cord - Italy (models)
1
Power cord - Australia / New Zealand (models)
Power cord - South Africa (models)
1
1
Power cord - Israel (models)
1
Power cord - China (PRC) (models)
1
Power cord - Taiwan (models)
1
Power cord - Korea (models)
1
Power cord - India (models)
1
Power cord - Thailand (models)
1
Power cord - US/Canada--optional second source (models)
Power cord - Japan-optional second source (models)
Power cord - Argentina - optional second source (models)
Power cord - Brazil (new type) - optional second source (models)
Power cord - Europe (Germany) - optional second source (models)
Power cord - UK - optional second source (models)
Power cord - Denmark - optional second source (models)
Power cord - Switzerland - optional second source (models)
Power cord - Italy - optional second source (models)
Power cord - Australia/New Zealand - optional second source (models)
Power cord - South Africa - optional second source (models)
Power cord - Israel - optional second source (models)
Power cord - China (PRC) - optional second source (models)
Power cord - Taiwan-optional second source (models)
Power cord - Korea-optional second source (models)
Power cord - India-optional second source (models)
Power cord - Thailand-optional second source (models)
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
6394 Windows XP Home Recovery CDs
FRU#
CRU
45R6005
45R6006
45R6007
45R6010
45R6009
45R6008
45R6014
45R6015
45R6020
45R6013
45R6018
1
1
1
1
1
1
1
1
1
1
1
US/UK/AP/TH (models)
FR/CF (models)
GR (models)
IT (models)
BR (models)
SP/LA (models)
DK (models)
NL (models)
AE (models)
SV (models)
HE (models)
98 Hardware Maintenance Manual
6394 Windows XP Home Recovery CDs
FRU#
CRU
1
45R6017
45R6012
45R6019
45R6030
45R6021
45R6029
45R6023
45R6016
45R6022
45R6024
45R6011
45R6025
45R6026
45R6027
45R6028
FI (models)
1
NO (models)
PL (models)
PO (models)
RU (models)
RE (models)
HU (models)
CZ (models)
TR (models)
GK (models)
Japanese (models)
1
1
1
1
1
1
1
1
1
1
Simplified Chinese (models)
Taiwan-TC (models)
1
1
Hong Kong-TC (models)
Korea (models)
1
6394 Windows XP Pro Recovery CDs
FRU#
CRU
1
45R5979
45R5980
45R5981
45R5984
45R5983
45R5982
45R5988
45R5989
45R5994
45R5987
45R5992
45R5991
45R5986
45R5993
45R6004
45R5995
45R6003
45R5997
45R5990
45R5996
45R5998
45R5985
US/UK/AP/TH (models)
FR/CF (models)
GR (models)
1
1
1
IT (models)
1
BR (models)
1
SP/LA (models)
DK (models)
1
1
NL (models)
1
AE (models)
1
SV (Swedish) (models)
HE (models)
1
1
FI (models)
1
NO (models)
PL (models)
1
1
PO (models)
1
RU (models)
1
RE (models)
1
HU (models)
1
CZ (models)
1
TR (models)
1
GK (models)
1
Japanese (models)
Chapter 9. FRU lists 99
6394 Windows XP Pro Recovery CDs
FRU#
CRU
45R5999
45R6000
45R6001
45R6002
45R5977
45R5978
1
1
1
1
1
1
Simplified Chinese (models)
Taiwan-TC (models)
Hong Kong-TC (models)
Korea (models)
Multilingual 1 XP-P -- EN, NL, FR, GR, IT (models)
Multilingual 2 XP-P -- EN, DK, FI, NO, SV (models)
6394 Vista Home Basic 32 Recovery DVDs
FRU#
CRU
1
46R7098
46R7099
46R7100
46R7101
46R7102
46R7103
46R7104
46R7105
46R7106
46R1086
46R7107
46R1088
46R1089
46R1090
46R1091
46R7108
46R1093
46R1094
46R1095
46R7109
46R7110
46R7111
46R1099
46R1100
46R1101
46R1102
46R1103
46R1104
English (models 13H)
Russian English (models)
French (models)
1
1
1
German (models)
Spanish (models)
Brazilian (models)
Italian (models)
1
1
1
1
Japanese (models)
Norwegian (models)
Swedish (models)
Danish (models)
1
1
1
1
Dutch (models)
1
Czech (models)
1
Finnish (models)
1
Polish (models)
1
Russian (models)
Turkish (models)
1
1
Hungarian (models)
Greek (models)
1
1
Simplified Chinese (models)
Taiwan (models)
1
1
Hong Kong (models)
Korea (models)
1
1
Slovenian (models)
Hebrew (models)
Portuguese (models)
Arabic Localized (models)
Slovakia (models)
1
1
1
1
100 Hardware Maintenance Manual
6394 Vista Business 32 Recovery DVDs
FRU#
CRU
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
46R7070
46R7071
46R7072
46R7073
46R7074
46R7075
46R7076
46R7077
46R7078
46R1028
46R7079
46R1030
46R1031
46R1032
46R1033
46R7080
46R1035
46R1036
46R1037
46R7081
46R7082
46R7083
46R1041
46R1042
46R1043
46R1044
46R1045
46R1046
46R1047
46R1048
English (models 15Q)
Russian (models)
French (models)
German (models)
Spanish (models 15S 15D 15Y 17S 17Y 18S 18Y)
Brazilian (models)
Italian (models)
Japanese (models)
Norwegian (models)
Swedish (models)
Danish (models)
Dutch (models)
Czech (models)
Finnish (models)
Polish (models)
Russian (models)
Turkish (models)
Hungarian (models)
Greek (models)
Simplified Chinese (models 15C)
Traditional Chinese (models)
Traditional Chinese (models)
Korean (models)
Slovenian (models)
Romanian (models)
Portuguese (models)
Serbian - Latin (models)
Slovakian (models)
Arabic Localized (models)
Hebrew (models)
6394 Vista Ultimate 32 Recovery DVDs
FRU#
CRU
46R7112
46R7113
46R7114
46R7115
46R7116
46R7117
46R7118
1
1
1
1
1
1
1
English (models)
Russian (models)
French (models)
German (models)
Spanish (models)
Brazilian (models)
Italian (models)
Chapter 9. FRU lists 101
6394 Vista Ultimate 32 Recovery DVDs
FRU#
CRU
1
46R7119
46R7120
46R1114
46R7121
46R1116
46R1117
46R1118
46R1119
46R7122
46R1121
46R1122
46R1123
46R7123
46R7124
46R7125
46R1127
46R1128
46R1129
46R1130
46R1131
46R1132
Japanese (models)
Norwegian (models)
Swedish (models)
Danish (models)
Dutch (models)
1
1
1
1
1
Czech (models)
Finnish (models)
Polish (models)
1
1
1
Russian (models)
Turkish (models)
Hungarian (models)
Greek (models)
1
1
1
1
Simplified Chinese (models)
Traditional Chinese (models)
Traditional Chinese (models)
Korean (models)
1
1
1
1
Slovenian (models)
1
Hebrew (models)
1
Portuguese (models)
Slovakian (models)
1
1
Arabic Localized (models)
6394 Vista Business 64 Recovery DVDs
FRU#
CRU
1
46R7084
46R7085
46R7086
46R7087
46R7088
46R7089
46R7090
46R7091
46R7092
46R1058
46R7093
46R1060
46R1061
46R1062
46R1063
46R7094
English (models)
Russian English (models)
French (models)
German (models)
Spanish (models)
Brazilian (models)
Italian (models)
1
1
1
1
1
1
1
Japanese (models)
Norwegian (models)
Swedish (models)
Danish (models)
Dutch (models)
1
1
1
1
1
Czech (models)
1
Finnish (models)
Polish (models)
1
1
Russian (models)
102 Hardware Maintenance Manual
6394 Vista Business 64 Recovery DVDs
FRU#
CRU
1
46R1065
46R1066
46R1067
46R7095
46R7096
46R7097
46R1071
46R1072
46R1073
46R1074
46R1075
46R1076
Turkish (models)
Hungarian (models)
Greek (models)
1
1
1
Simplified Chinese (models)
Taiwan (models)
1
1
Hong Kong (models)
Korea (models)
1
1
Slovenian (models)
Arabic Localized (models)
Hebrew (models)
1
1
1
Portuguese (models)
Slovakian (models)
1
Machine Type 6395
Item
#
6395 FRUs
FRU#
CRU
N
1
2
41R8510
40Y9034
Front audio/USB card and cable (included in Cables kit) (all models)
2
Hard disk drive, 80 GB 7200rpm SATA (models 11S 11D 11Y 11A 11T 12S 12D 12Y
12G 13S 13G 13C 13B 13H 16S 16G)
Chapter 9. FRU lists 103
Item
#
6395 FRUs
FRU#
CRU
2
40Y9035
2
Hard disk drive, 160 GB 7200rpm SATA (models 14S 14D 14Y 14M 14A 14T 14K 14J
15M 15A 15Q 17U 17F 17S 17D 17Y 17G 17M 17A 17T 17K 17J 18S 18D 18Y 18A
18Q 18T 18C 18B 18H 19S 19A 19Q 19T 19K 19J 21S 21D 21Y 21A 21Q 21T 21B 21H
21V 21K 21J 23U 23F 23S 23L 23D 23Y 23G 23M 23A 23Q 23T 23C 23B 23H 23V 23K
23R 23E 23J 24U 24F 24G 24M 24A 24T 24K 24J 25S 25D 25Y 27U 27F 28U 28F 29U
29F 29S 29L 29D 29Y 29G 29M 29A 29Q 29T 29C 29B 29H 29V 29K 29R 29E 29J 31U
31F 33S 33K 33J 33A 33Q 33T 34S 34D 34Y 34A 34Q 34T 34B 34H 34V 34K 34J 36U
36F 36S 36L 36D 36Y 36G 36M 36A 36Q 36T 36C 36B 36H 36V 36K 36R 36E 36J 38A
38Q 38T 38K 39M 39A 39Q 39T 39K 39J 41M 41A 41Q 41T 41K 41J 42M 42A 42J 43M
43A 43Q 43T 43K 43J 44A 44Q 44T 24Q 45M 45A 45Q 45T 45K 45J 46M 46A 46Q 46T
46K 46J 33M 34M 61U 61F 61S 62U 63M 63A 63Q 63T 63K 63J 65A 65Q 65T 65K
66G 67S 67Y 67M 67A 67T 67K 67J 68S 68Y 68G 68M 68A 68T 68K 68J 69S 69Y 81S
81Y 81M 81A 81Q 81T 81K 81J 82U 82F 82M 82A 82Q 82T 82K 82J 83U 83F 84U 84F
84M 84A 84Q 84T 84K 84J 86U 86F 87U 87F 88U 88F 89U 89F 54U 54F 57U 57F)
2
2
40Y9036
87H4891
2
2
Hard disk drive, 250 GB 7200rpm SATA (models 22B 22H 22V 32S 32D 32Y 35B 35H
35V 64M 64A 64Q 64T 64K 64J 83U 83F 85U 85F 55U 55F 56U 56F)
Hard disk drive, 320 GB 7200rpm SATA (models 26U 26F 26M 26A 26Q 26T 26K 26J
47M 47A 47Q 47T 47K 47J 49M 49A 49Q 49T 49K 49J 51M 51A 51Q 51T 51K 51J)
2
2
2
3
41X5582
43C3671
45C5973
41R8511
2
2
2
2
Hard disk drive, 500 GB 7200rpm SATA (models 52M 52A 52Q 52T 52K 52J )
Hard disk drive, 750 GB 7200rpm SATA (models)
Hard disk drive, 1TB 7200rpm SATA (models CTO)
System fan (all models)
4
41N3325
2
DVD-ROM Drive - 16x/48x - SATA (models 11S 11D 11Y 11A 11T 12S 12D 12Y 12G
13S 13G 13C 13B 13H 14S 14D 14Y 14M 14A 14T 14K 16S 16G 17U 17F 17S 17D
17Y 17G 17M 17A 17T 17K 17J 19S 19A 19Q 19T 19K 19J 27U 27F 28U 28F 33S 33K
33J 33A 33Q 33T 38A 38Q 38T 38K 39M 39A 39Q 39T 39K 39J 44A 44Q 44T 33M
61U 61F 61S 62U 65A 65Q 65T 65K 67S 67Y 67M 67A 67T 67K 67J 69S 69Y 82U
82F 82M 82A 82Q 82T 82K 82J 84U 84F 84M 84A 84Q 84T 84K 84J 86U 86F 88U
88F 54U 54F 57U 57F)
4
2
DVD-ROM Drive - DVD-RW/CD-RW Rambo 8 (SATA) Matrix (models 15M 15A 15Q 15T 43C1042
18S 18D 18Y 18A 18Q 18T 18C 18B 18H 21S 21D 21Y 21A 21Q 21T 21B 21H 21V
21K 21J 22B 22H 22V 23U 23F 23S 23L 23D 23Y 23G 23M 23A 23Q 23T 23C 23B
23H 23V 23K 23R 23E 23J 24U 24F 24G 24M 24A 24T 24K 24J 25S 25D 25Y 26U 26F
26M 26A 26Q 26T 26K 26J 29U 29F 29S 29L 29D 29Y 29G 29M 29A 29Q 29T 29C
29B 29H 29V 29K 29R 29E 29J 31U 31F 32S 32D 32Y 34S 34D 34Y 34A 34Q 34T 34B
34H 34V 34K 34J 35B 35H 35V 36U 36F 36S 36L 36D 36Y 36G 36M 36A 36Q 36T
36C 36B 36H 36V 36K 36R 36E 36J 41M 41A 41Q 41T 41K 41J 42M 42A 42J 43M
43A 43Q 43T 43K 43J 24Q 45M 45A 45Q 45T 45K 45J 46M 46A 46Q 46T 46K 46J
47M 47A 47Q 47T 47K 47J 49M 49A 49Q 49T 49K 49J 51M 51A 51Q 51T 51K 51J
52M 52A 52Q 52T 52K 52J 34M 63M 63A 63Q 63T 63K 63J 64M 64A 64Q 64T 64K
64J 66G 68S 68Y 68G 68M 68A 68T 68K 68J 81S 81Y 81M 81A 81Q 81T 81K 81J
83U 83F 85U 85F 87U 87F 89U 89F 55U 55F 56U 56F)
4
42Y9353
2
DVD-ROM Drive - DVD-ROM/CD-RW Combo Drive - 48x/32x/48x/16x - SATA Matrix
(models)
104 Hardware Maintenance Manual
Item
#
6395 FRUs
FRU#
CRU
5
41A9732
1
Power Adapter, 120W AC/DC (models 11S 11D 11Y 11A 11T 12S 12D 12Y 12G 13S
13G 13C 13B 13H 14S 14D 14Y 14M 14A 14T 14K 14J 15M 15A 15Q 15T 16S 16G
17U 17F 17S 17D 17Y 17G 17M 17A 17T 17K 17J 18S 18D 18Y 18A 18Q 18T 18C 18B
18H 19S 19A 19Q 19T 19K 19J 21S 21D 21Y 21A 21Q 21T 21B 21H 21V 21K 21J 22B
22H 22V 23U 23F 23S 23L 23D 23Y 23G 23M 23A 23Q 23T 23C 23B 23H 23V 23K
23R 23E 23J 24U 24F 24G 24M 24A 24T 24K 24J 25S 25D 25Y 26U 26F 26M 26A 26Q
26T 26K 26J 27U 27F 28U 28F 29U 29F 29S 29L 29D 29Y 29G 29M 29A 29Q 29T 29C
29B 29H 29V 29K 29R 29E 29J 31U 31F 32S 32D 32Y 33S 33K 33J 33A 33Q 33T 34S
34D 34Y 34A 34Q 34T 34B 34H 34V 34K 34J 35B 35H 35V 36U 36F 36S 36L 36D 36Y
36G 36M 36A 36Q 36T 36C 36B 36H 36V 36K 36R 36E 36J 38A 38Q 38T 38K 39M
39A 39Q 39T 39K 39J 41M 41A 41Q 41T 41K 41J 42M 42A 42J 43M 43A 43Q 43T 43K
43J 44A 44Q 44T 24Q 45M 45A 45Q 45T 45K 45J 46M 46A 46Q 46T 46K 46J 47M
47A 47Q 47T 47K 47J 49M 49A 49Q 49T 49K 49J 51M 51A 51Q 51T 51K 51J 52M 52A
52Q 52T 52K 52J 33M 34M 61U 61F 61S 62U 63M 63A 63Q 63T 63K 63J 64M 64A
64Q 64T 64K 64J 65A 65Q 65T 65K 66G 67S 67Y 67M 67A 67T 67K 67J 68S 68Y 68G
68M 68A 68T 68K 68J 69S 69Y 81S 81Y 81M 81A 81Q 81T 81K 81J 82U 82F 82M 82A
82Q 82T 82K 82J 83U 83F 84U 84F 84M 84A 84Q 84T 84K 84J 85U 85F 86U 86F 87U
87F 88U 88F 89U 89F 54U 54F 55U 55F 56U 56F 57U 57F)
5
41A9747
1
Power Adapter, 120W power adapter (models 11S 11D 11Y 11A 11T 12S 12D 12Y 12G
13S 13G 13C 13B 13H 14S 14D 14Y 14M 14A 14T 14K 14J 15M 15A 15Q 15T 16S
16G 17U 17F 17S 17D 17Y 17G 17M 17A 17T 17K 17J 18S 18D 18Y 18A 18Q 18T 18C
18B 18H 19S 19A 19Q 19T 19K 19J 21S 21D 21Y 21A 21Q 21T 21B 21H 21V 21K 21J
22B 22H 22V 23U 23F 23S 23L 23D 23Y 23G 23M 23A 23Q 23T 23C 23B 23H 23V
23K 23R 23E 23J 24U 24F 24G 24M 24A 24T 24K 24J 25S 25D 25Y 26U 26F 26M 26A
26Q 26T 26K 26J 27U 27F 28U 28F 29U 29F 29S 29L 29D 29Y 29G 29M 29A 29Q 29T
29C 29B 29H 29V 29K 29R 29E 29J 31U 31F 32S 32D 32Y 33S 33K 33J 33A 33Q 33T
34S 34D 34Y 34A 34Q 34T 34B 34H 34V 34K 34J 35B 35H 35V 36U 36F 36S 36L 36D
36Y 36G 36M 36A 36Q 36T 36C 36B 36H 36V 36K 36R 36E 36J 38A 38Q 38T 38K
39M 39A 39Q 39T 39K 39J 41M 41A 41Q 41T 41K 41J 42M 42A 42J 43M 43A 43Q
43T 43K 43J 44A 44Q 44T 24Q 45M 45A 45Q 45T 45K 45J 46M 46A 46Q 46T 46K 46J
47M 47A 47Q 47T 47K 47J 49M 49A 49Q 49T 49K 49J 51M 51A 51Q 51T 51K 51J
52M 52A 52Q 52T 52K 52J 33M 34M 61U 61F 61S 62U 63M 63A 63Q 63T 63K 63J
64M 64A 64Q 64T 64K 64J 65A 65Q 65T 65K 66G 67S 67Y 67M 67A 67T 67K 67J 68S
68Y 68G 68M 68A 68T 68K 68J 69S 69Y 81S 81Y 81M 81A 81Q 81T 81K 81J 82U 82F
82M 82A 82Q 82T 82K 82J 83U 83F 84U 84F 84M 84A 84Q 84T 84K 84J 85U 85F 86U
86F 87U 87F 88U 88F 89U 89F 54U 54F 55U 55F 56U 56F 57U 57F)
6
7
41R8570
46R3849
N
N
Express Card Assembly (all models)
System board, Mini-ITX Intel (Q35, ICH9DO) (models 25S 25D 25Y 26U 26F 26M
26A 26Q 26T 26K 26J 27U 27F 28U 28F 29U 29F 29S 29L 29D 29Y 29G 29M 29A
29Q 29T 29C 29B 29H 29V 29K 29R 29E 29J 31U 31F 32S 32D 32Y 33S 33K 33J
33A 33Q 33T 34S 34D 34Y 34A 34Q 34T 34B 34H 34V 34K 34J 35B 35H 35V 36U
36F 36S 36L 36D 36Y 36G 36M 36A 36Q 36T 36C 36B 36H 36V 36K 36R 36E 36J
37U 37F 37G 51M 51A 51Q 51T 51K 51J 52M 52A 52Q 52T 52K 52J 33M 34M 54U
54F 55U 55F 56U 56F 57U 57F)
Chapter 9. FRU lists 105
Item
#
6395 FRUs
FRU#
CRU
7
46R3848
N
System board, non-AMT Mini-ITX Intel (Q35, ICH9DO) (models 11S 11D 11Y 11A 11T
12S 12D 12Y 12G 13S 13G 13C 13B 13H 14S 14D 14Y 14M 14A 14T 14K 14J 15M
15A 15Q 15T 16S 16G 17U 17F 17S 17D 17Y 17G 17M 17A 17T 17K 17J 18S 18D 18Y
18A 18Q 18T 18C 18B 18H 19S 19A 19Q 19T 19K 19J 21S 21D 21Y 21A 21Q 21T 21B
21H 21V 21K 21J 22B 22H 22V 23U 23F 23S 23L 23D 23Y 23G 23M 23A 23Q 23T 23C
23B 23H 23V 23K 23R 23E 23J 24U 24F 24G 24M 24A 24T 24K 24J 38A 38Q 38T 38K
39M 39A 39Q 39T 39K 39J 41M 41A 41Q 41T 41K 41J 42M 42A 42J 43M 43A 43Q
43T 43K 43J 44A 44Q 44T 24Q 45M 45A 45Q 45T 45K 45J 46M 46A 46Q 46T 46K 46J
47M 47A 47Q 47T 47K 47J 49M 49A 49Q 49T 49K 49J 61U 61F 61S 62U 63M 63A
63Q 63T 63K 63J 64M 64A 64Q 64T 64K 64J 65A 65Q 65T 65K 66G 67S 67Y 67M 67A
67T 67K 67J 68S 68Y 68G 68M 68A 68T 68K 68J 69S 69Y 81S 81Y 81M 81A 81Q 81T
81K 81J 82U 82F 82M 82A 82Q 82T 82K 82J 83U 83F 84U 84F 84M 84A 84Q 84T
84K 84J 85U 85F 86U 86F 87U 87F 88U 88F 89U 89F)
8
8
8
N
N
N
Microprocessor, Intel Conroe E6750 (Core2 Duo) 2.66GHz, G-0 Stepping, 65nm,
1333MHZ FSB, 4MB L2 (models)
45C6898
45C6899
45C6900
Microprocessor, Intel Conroe E6550 (Core2 Duo) 2.33GHz, G-0 Stepping, 65nm,
1333MHz FSB, 4MB L2 (models)
Microprocessor, Intel Conroe E4500 (Core2 Duo) 2.20GHz, M-0 Stepping, 65nm,
800MHz FSB, 2MB L2 (models 16S 16G 17U 17F 17S 17D 17Y 17G 17M 17A 17T 17K
17J 18S 18D 18Y 18A 18Q 18T 18C 18B 18H 43M 43A 43Q 43T 43K 43J 44A 44Q 44T)
8
N
Microprocessor, Intel Conroe E2160 (Pentium D) 1.8GHz, M-0 Stepping, 65nm,
800MHz FSB, 1MB L2 (models 38A 38Q 38T 38K 39M 39A 39Q 39T 39K 39J 41M
41A 41Q 41T 41K 41J 42M 42A)
45C6901
8
8
N
N
Microprocessor, Intel Conroe-L 440 (Celeron) 2.0GHz, A-1 Stepping, 65nm, 800MHz
FSB, 512KB L2 (models)
45C6902
45C8499
Microprocessor, Intel Wolfdale E8400 (Core2 Duo) 3.0GHz, C-0 Stepping, 45nm,
1333MHz FSB, 6MB L2 (models 25S 25D 25Y 26U 26F 26M 26A 26Q 26T 26K 26J
27U 27F 28U 28F 29U 29F 29S 29L 29D 29Y 29G 29M 29A 29Q 29T 29C 29B 29H 29V
29K 29R 29E 29J 31U 31F 32S 32D 32Y 49M 49A 49Q 49T 49K 49J 51M 51A 51Q 51T
51K 51J 52M 52A 52Q 52T 52K 52J 86U 86F 87U 87F 54U 54F 55U 55F)
8
N
Microprocessor, Intel Wolfdale E8200 (Core2 Duo) 2.66GHz, C-0 Stepping, 45nm,
1333MHz FSB, 6MB L2 (models 19S 19A 19Q 19T 19K 19J 21S 21D 21Y 21A 21Q
21T 21B 21H 21V 21K 21J 22B 22H 22V 23U 23F 23S 23L 23D 23Y 23G 23M 23A
23Q 23T 23C 23B 23H 23V 23K 23R 23E 23J 24U 24F 24G 24M 24A 24T 24K 24J 33S
33K 33J 33A 33Q 33T 34S 34D 34Y 34A 34Q 34T 34B 34H 34V 34K 34J 35B 35H 35V
36U 36F 36S 36L 36D 36Y 36G 36M 36A 36Q 36T 36C 36B 36H 36V 36K 36R 36E
36J 24Q 45M 45A 45Q 45T 45K 45J 46M 46A 46Q 46T 46K 46J 47M 47A 47Q 47T
47K 47J 33M 34M 88U 88F 89U 89F 56U 56F 57U 57F)
45C8531
8
8
46R4261
46R4260
N
N
Microprocessor, E7200, 2.53GHz, 1066MHz FSB, 3MB L2 (models 19S 19A 19Q 19T
19K 19J 21S 21D 21Y 21A 21Q 21T 21B 21H 21V 21K 21J 22B 22H 22V 23U 23F 23S
23L 23D 23Y 23G 23M 23A 23Q 23T 23C 23B 23H 23V 23K 23R 23E 23J 24U 24F 24G
24M 24A 24T 24K 24J 33S 33K 33J 33A 33Q 33T 34S 34D 34Y 34A 34Q 34T 34B 34H
34V 34K 34J 35B 35H 35V 36U 36F 36S 36L 36D 36Y 36G 36M 36A 36Q 36T 36C 36B
36H 36V 36K 36R 36E 36J 24Q 45M 45A 45Q 45T 45K 45J 46M 46A 46Q 46T 46K 46J
47M 47A 47Q 47T 47K 47J 33M 34M 88U 88F 89U 89F 56U 56F 57U 57F)
Microprocessor, E2200, 2.20GHz, 800MHz FSB, 1MB L2 (models 63M 63A 63Q 63T
63K 63J 65A 65Q 65T 65K 67S 67Y 67M 67A 67T 67K 67J 68S 68Y 68G 68M 68A 68T
68K 68J 84U 84F 84M 84A 84Q 84T 84K 84J 85U 85F)
9
41R8545
43C3814
2
2
Heat sink Intel (all models)
11
Memory module, 512MB DDR2 PC2-5300 (667MHz) SoDIMM (models 1S 11D 11Y
11A 11T 12S )
106 Hardware Maintenance Manual
Item
#
6395 FRUs
FRU#
CRU
11
2
Memory module, 1GB DDR2 PC2-5300 (667MHz) SoDIMM (models 12S 12D 12Y 12G
13S 13G 13C 13B 13H 14S 14D 14Y 14M 14A 14T 14K 14J 15M 15A 15Q 15T 16S
16G 17U 17F 17S 17D 17Y 17G 17M 17A 17T 17K 17J 18S 18D 18Y 18A 18Q 18T
18C 18B 18H 19S 19A 19Q 19T 19K 19J 21S 21D 21Y 21A 21Q 21T 21B 21H 21V
21K 21J 22B 22H 22V 33S 33K 33J 33A 33Q 33T 34S 34D 34Y 34A 34Q 34T 34B 34H
34V 34K 34J 35B 35H 35V 38A 38Q 38T 38K 39M 39A 39Q 39T 39K 39J 41M 41A
41Q 41T 41K 41J 42M 42A 42J 43M 43A 43Q 43T 43K 43J 44A 44Q 44T 46M 46A
46Q 46T 46K 46J 33M 34M 61U 61F 61S)
43C3815
11
2
Memory module, 2GB DDR2 PC2-5300 (667MHz) SoDIMM (models 27U 27F 28U 28F
29U 29F 29S 29L 29D 29Y 29G 29M 29A 29Q 29T 29C 29B 29H 29V 29K 29R 29E 29J
31U 31F 32S 32D 32Y 36U 36F 36S 36L 36D 36Y 36G 36M 36A 36Q 36T 36C 36B
36H 36V 36K 36R 36E 36J 47M 47A 47Q 47T 47K 47J 49M 49A 49Q 49T 49K 49J 24Q
45M 45A 45Q 45T 45K 45J 51M 51A 51Q 51T 51K 51J 52M 52A 52Q 52T 52K 52J)
43C6489
12
13
41R8517
41R8568
2
Internal speaker (all models)
Media card reader (all models)
N
The FRUs listed in the following tables are not illustrated.
6395 FRUs
Hard Disk Drive tray (all models)
Shield Kit (all models)
FRU#
CRU
2
41R8518
41R8543
41R8544
41R8548
41R8560
41R8563
41R8555
N
N
Cable, C2 Swtich/Housing assembly (all models)
Cable, Serial (all models)
N
N
USB Cable (all models)
N
Kit, Shell (all models)
N
PWR/LED Cable Asm (all models)
6395 Keyboards (USB Preferred Pro)
FRU#
CRU
41A5289
1
US English (models 11A 12G 13G 13H 14M 14A 15M 15A 15Q 16G 17U 17G 17M 17A 18A
18Q 18H 19A 19Q 21A 21Q 21H 22H 23U 23L 23G 23M 23A 23Q 23H 24U 24G 24M 24A 26U
26M 26A 26Q 27U 28U 29L 29G 29M 29A 29Q 29H 29R 29E 31U 36U 37U 36L 36G 33A
33Q 34A 34Q 36M 36A 36Q 34H 35H 36H 36E 36R 38A 38Q 39M 39A 39Q 41M 41A 41Q
42M 42A 43M 43A 43Q 44A 44Q 24Q 45M 45A 45Q 46M 46Q 46A 47M 47Q 47A 49M 49A
49Q 51M 51A 51Q 52M 52A 52Q 33M 34M 61U 62U 63M 63A 63Q 64M 64A 64Q 65A 65Q
66G 67M 67A 68G 68M 68A 81M 81A 81Q 83U 84U 84M 84A 84Q 85U 86U 87U 88U 89U
54U 55U 56U 57U)
41A5290
41A5291
41A5292
41A5293
41A5294
41A5295
41A5296
41A5297
41A5298
1
1
1
1
1
1
1
1
1
Arabic(models)
Arabic/French (models 12G 13G 16G 17G 23G 24G 29G 36G 37G 66G 68G)
Belgian/French (models 12G 13G 16G 17G 23G 24G 29G 36G 37G 66G 68G)
Belgian/UK (models 12G 13G 16G 17G 23G 24G 29G 36G 37G 66G 68G)
Brazilian (models)
Bulgarian (models 12G 13G 16G 17G 23G 24G 29G 36G 37G 66G 68G)
Hong Kong/Taiwan (models 34B 35B 36B 34V 35V 36V)
Czech (models 12G 13G 16G 17G 23G 24G 29G 36G 37G 66G 68G)
Danish (models 12G 13G 16G 17G 23G 24G 29G 36G 37G 66G 68G)
Chapter 9. FRU lists 107
6395 Keyboards (USB Preferred Pro)
Dutch (models 12G 13G 16G 17G 23G 24G 29G 36G 37G 66G 68G)
French (models 12G 13G 16G 17G 23G 24G 29G 36G 37G 66G 68G)
FRU#
CRU
41A5299
41A5300
41A5301
1
1
1
French Canadian 445 (models 17F 23F 24F 26F 27F 28F 31F 36F 37F 61F 83F 84F 85F
86F 87F 88U 89F 54F 55F 56F 57F)
41A5302
1
French Canadian 58 (models 17F 23F 24F 26F 27F 28F 31F 36F 37F 61F 83F 84F 85F 86F
87F 88U 89F 54F 55F 56F 57F )
41A5303
41A5304
41A5305
41A5306
41A5307
41A5308
41A5309
41A5310
1
1
1
1
1
1
1
1
German (models 12G 13G 16G 17G 23G 24G 29G 36G 37G 66G 68G)
Greek (models 12G 13G 16G 17G 23G 24G 29G 36G 37G 66G 68G)
Greek/US (models 12G 13G 16G 17G 23G 24G 29G 66G 68G)
Hebrew (models 12G 13G 16G 17G 23G 24G 29G 36G 37G 66G 68G)
Hungarian (models 12G 13G 16G 17G 23G 24G 29G 36G 37G 66G 68G)
Iceland (models 112G 13G 16G 17G 23G 24G 29G 36G 37G 66G 68G)
Italian (models 12G 13G 16G 17G 23G 24G 29G 36G 37G 66G 68G)
Japanese (models 14J 17J 19J 21J 23J 24J 26J 29J 33J 34J 36J 39J 41J 42J 43J 45J 46J
47J 49J 51J 52J 63J 64J 67J 68J 81J 84J)
41A5311
41A5312
1
1
Korean (models 11K14K 17K 19K 21K 23K 24K 26K 29K 33K 34K 36K 38K 39K 41K 43K
45K 46K 47K 49K 51K 52K 63K 64K 65K 67K 68K 81K 84K )
LA Spanish (models 11S 11D 11Y 12S 12D 12Y 13S 14S 14D 14Y 16S 17S 17D 17Y 18S
18D 18Y 19S 21S 21D 21Y 23S 23D 23Y 25S 25D 25Y 29S 29D 29Y 32S 32D 32Y 33S 34S
36S 34D 36D 34Y 36Y 67S 67Y 68S 68Y 69S 69Y 81S 81Y )
41A5313
41A5314
41A5315
41A5316
41A5317
41A5318
41A5319
41A5320
41A5321
41A5322
41A5323
41A5324
1
1
1
1
1
1
1
1
1
1
1
1
Norwegian (models 12G 13G 16G 17G 23G 24G 29G 36G 37G 66G 68G)
Polish (models 12G 13G 16G 17G 23G 24G 29G 36G 37G 66G 68G)
Portuguese (models 12G 13G 16G 17G 23G 24G 29G 36G 37G 66G 68G )
Romanian 446 (models 12G 13G 16G 17G 23G 24G 29G 36G 37G 66G 68G)
Romanian 096 (models 12G 13G 16G 17G 23G 24G 29G 36G 37G 66G 68G)
Russian/Cyrillic(models 12G 13G 16G 17G 23G 24G 29G 36G 37G 66G 68G)
Serbian/Cyrillic (models 12G 13G 16G 17G 23G 24G 29G 36G 37G 66G 68G)
Slovak (models 12G 13G 16G 17G 23G 24G 29G 36G 37G 66G 68G)
Spanish (models 12G 13G 16G 17G 23G 24G 29G 36G 37G 66G 68G)
Swedish/Finn (models 12G 13G 16G 17G 23G 24G 29G 36G 37G 66G 68G)
Swiss (models 12G 13G 16G 17G 23G 24G 29G 36G 37G 66G 68G)
Thailand (models 11T 14T 15T 18T 19T 21T 33T 34T 36T 38T 39T 41T 43T 44T 45T 46T 47T
49T 51T 52T 63T 64T 65T 67T 68T 81T 84T )
41A5325
41A5326
41A5327
41A5328
41A5329
1
1
1
1
1
Turkish 440 (models 12G 13G 16G 17G 23G 24G 29G 36G 37G 66G 68G)
Turkish 179 (models 12G 13G 16G 17G 23G 24G 29G 36G 37G 66G 68G)
UK English (models 12G 13G 16G 17G 23G 24G 29G 36G 37G 66G 68G)
US Euro (models 12G 13G 16G 17G 23G 24G 29G 36G 37G 66G 68G)
Slovenian (models 12G 13G 16G 17G 23G 24G 29G 36G 37G 66G 68G)
6395 Keyboard (USB Preferred Pro Fingerprint Keyboard)
FRU#
CRU
41A5248
41A5249
1
1
US (models)
Arabic (models)
108 Hardware Maintenance Manual
6395 Keyboard (USB Preferred Pro Fingerprint Keyboard)
Arabic/French (models)
FRU#
CRU
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
41A5250
41A5251
41A5252
41A5253
41A5254
41A5255
41A5256
41A5257
41A5258
41A5259
41A5260
41A5261
41A5262
41A5263
41A5264
41A5265
41A5266
41A5267
41A5268
41A5269
41A5270
41A5271
41A5272
41A5273
41A5274
41A5276
41A5275
41A5277
41A5278
41A5279
41A5280
41A5281
41A5282
41A5283
41A5284
41A5285
41A5286
41A5287
41A5288
Belgian/French (models)
Belgian/UK (models)
Brazil/Portuguese (models)
Bulgarian (models)
Chinese/US (models)
Czech (models)
Danish (models)
Dutch (models)
French (models)
French Canadian 445 (models)
French Canadian 58 (models)
German (models)
Greek (models)
Greek/US (models)
Hebrew (models)
Hungarian (models)
Iceland (models)
Italian (models)
Japanese (models)
Korean (models)
LA Spanish (models)
Norwegian (models)
Polish (models)
Portuguese (models)
Romanian 446 (models)
Romanian 96 (models)
Russian/Cyrillic (models)
Serbian/Cyrillic (models)
Slovak (models)
Spanish (models)
Swedish/Finn (models)
Swiss, F/G (models)
Thailand (models)
Turkish 179 (models)
Turkish 440 (models)
UK (models)
US European (models)
Slovenian (models)
Chapter 9. FRU lists 109
6395 mice
FRU#
CRU
41U3013
1
Optical wheel mouse (400DPI, USB) (models 11S 11D 11Y 11A 11T 12S 12D 12Y 12G 13S
13G 13C 13B 13H 14S 14D 14Y 14M 14A 14T 14K 14J 15M 15A 15Q 15T 16S 16G 17U 17F
17S 17D 17Y 17G 17M 17A 17T 17K 17J 18S 18D 18Y 18A 18Q 18T 18C 18B 18H 19S 19A
19Q 19T 19K 19J 21S 21D 21Y 21A 21Q 21T 21B 21H 21V 21K 21J 22B 22H 22V 23U 23F
23S 23L 23D 23Y 23G 23M 23A 23Q 23T 23C 23B 23H 23V 23K 23R 23E 23J 24U 24F 24G
24M 24A 24T 24K 24J 25S 25D 25Y 26U 26F 26M 26A 26Q 26T 26K 26J 27U 27F 28U 28F
29U 29F 29S 29L 29D 29Y 29G 29M 29A 29Q 29T 29C 29B 29H 29V 29K 29R 29E 29J 31U
31F 32S 32D 32Y 33S 33K 33J 33A 33Q 33T 34S 34D 34Y 34A 34Q 34T 34B 34H 34V 34K
34J 35B 35H 35V 36U 36F 36S 36L 36D 36Y 36G 36M 36A 36Q 36T 36C 36B 36H 36V 36K
36R 36E 36J 38A 38Q 38T 38K 39M 39A 39Q 39T 39K 39J 41M 41A 41Q 41T 41K 41J 42M
42A 42J 43M 43A 43Q 43T 43K 43J 44A 44Q 44T 24Q 45M 45A 45Q 45T 45K 45J 46M 46A
46Q 46T 46K 46J 47M 47A 47Q 47T 47K 47J 49M 49A 49Q 49T 49K 49J 51M 51A 51Q 51T
51K 51J 52M 52A 52Q 52T 52K 52J 33M 34M 61U 61F 61S 62U 63M 63A 63Q 63T 63K 63J
64M 64A 64Q 64T 64K 64J 65A 65Q 65T 65K 66G 67S 67Y 67M 67A 67T 67K 67J 68S 68Y
68G 68M 68A 68T 68K 68J 69S 69Y 81S 81Y 81M 81A 81Q 81T 81K 81J 82U 82F 82M 82A
82Q 82T 82K 82J 83U 83F 84U 84F 84M 84A 84Q 84T 84K 84J 85U 85F 86U 86F 87U 87F
88U 88F 89U 89F 54U 54F 55U 55F 56U 56F 57U 57F)
41U3030
1
Optical wheel mouse (400DPI, USB) (models 11S 11D 11Y 11A 11T 12S 12D 12Y 12G 13S
13G 13C 13B 13H 14S 14D 14Y 14M 14A 14T 14K 14J 15M 15A 15Q 15T 16S 16G 17U 17F
17S 17D 17Y 17G 17M 17A 17T 17K 17J 18S 18D 18Y 18A 18Q 18T 18C 18B 18H 19S 19A
19Q 19T 19K 19J 21S 21D 21Y 21A 21Q 21T 21B 21H 21V 21K 21J 22B 22H 22V 23U 23F
23S 23L 23D 23Y 23G 23M 23A 23Q 23T 23C 23B 23H 23V 23K 23R 23E 23J 24U 24F 24G
24M 24A 24T 24K 24J 25S 25D 25Y 26U 26F 26M 26A 26Q 26T 26K 26J 27U 27F 28U 28F
29U 29F 29S 29L 29D 29Y 29G 29M 29A 29Q 29T 29C 29B 29H 29V 29K 29R 29E 29J 31U
31F 32S 32D 32Y 33S 33K 33J 33A 33Q 33T 34S 34D 34Y 34A 34Q 34T 34B 34H 34V 34K
34J 35B 35H 35V 36U 36F 36S 36L 36D 36Y 36G 36M 36A 36Q 36T 36C 36B 36H 36V 36K
36R 36E 36J 38A 38Q 38T 38K 39M 39A 39Q 39T 39K 39J 41M 41A 41Q 41T 41K 41J 42M
42A 42J 43M 43A 43Q 43T 43K 43J 44A 44Q 44T 24Q 45M 45A 45Q 45T 45K 45J 46M 46A
46Q 46T 46K 46J 47M 47A 47Q 47T 47K 47J 49M 49A 49Q 49T 49K 49J 51M 51A 51Q 51T
51K 51J 52M 52A 52Q 52T 52K 52J 33M 34M 61U 61F 61S 62U 63M 63A 63Q 63T 63K 63J
64M 64A 64Q 64T 64K 64J 65A 65Q 65T 65K 66G 67S 67Y 67M 67A 67T 67K 67J 68S 68Y
68G 68M 68A 68T 68K 68J 69S 69Y 81S 81Y 81M 81A 81Q 81T 81K 81J 82U 82F 82M 82A
82Q 82T 82K 82J 83U 83F 84U 84F 84M 84A 84Q 84T 84K 84J 85U 85F 86U 86F 87U 87F
88U 88F 89U 89F 54U 54F 55U 55F 56U 56F 57U 57F)
41U3019
1
Scroll point optical mouse (800DPI, USB) (models )
6395 Adapters and miscellaneous FRUs
Modem daughter card (MDC 1.5) kit (models)
FRU#
CRU
39T0495
41R8522
41A5331
41A5334
89P8571
91P8835
41R4770
2
2
1
1
1
N
2
Modem daughter card (MDC 1.5) kit internal cable /RJ11 (models)
Lenovo branded speakers - 2 piece--primary (models)
Lenovo branded speakers - 2 piece--secondary (models)
Speaker power brick (models)
Thermal grease syringe (models)
Vertical PC stand (VPC) for blue 4.5L chassis (models)
110 Hardware Maintenance Manual
6395 Power Cords
FRU#
CRU
42T5004
1
Power cord - US/Canada (models 11S 11D 12S 12D 13S 14S 14D 16S 17S 17D 18S 18D 19S
21S 21D 23S 23D 25S 25D 29S 29D 32S 32D 23L 29L 11A 11T 14A 14T 15A 15T 17A 17T
18A 18T 19A 19T 21A 21T 23A 23T 24A 24T 26A 26T 29A 29T 17U 17F 23U 23F 26U 26F 27U
27F 28U 28F 29U 29F 31U 31F 36U 37U 36F 37F 33S 34S 36S 34D 36D 33A 34A 36A 33T
34T 36T 38A 39A 41A 42A 43A 44A 45A 46A 47A 49A 51A 52A 38T 39T 41T 43T 44T 45T 46T
47T 49T 51T 52T 61U 61F 61S 62U 63A 64A 65A 67S 67A 68S 69S 82U 82F 83U 83F 84U
84F 84A 85U 85F 86U 86F 87U 87F 88U 88F 89U 89F 54U 54F 55U 55F 56U 56F 57U 57F)
42T5011
42T5017
1
1
Power cord - Japan (models 14J 15J 17J 19J 21J 23J 24J 26J 36E 34J 33J 36J 39J 41J 42J
43J 45J 46J 47J 49J 51J 52J 63J 64J 67J 68J 82J 84J)
Power cord - Argentina (models 23L 29L 11Y 12Y 14Y 17Y 18Y 21Y 23Y 25Y 29Y 32Y 36L
34Y 36Y )
42T5174
42T5029
1
1
Power cord - Brazil (models)
Power cord - Europe (Germany) (models 11A 14A 15A 17A 18A 19A 21A 23A 24A 26A 29A
33A 34A 36A 38A 39A 41A 42A 43A 44A 45A 46A 47A 49A 51A 52A 63A 64A 65A 67A 68A
81A 84A)
42T5035
1
Power cord - UK (models 11A 14A 15A 17A 18A 19A 21A 23A 24A 26A 29A 12G 13G 16G
17G 23G 24G 29G 33A 34A 36A 38A 39A 41A 42A 43A 44A 45A 46A 47A 49A 51A 52A
63A 64A 65A 67A 68A 81A 84A)
42T5041
42T5044
42T5047
1
1
1
Power cord - Denmark (models 12G 13G 16G 17G 23G 24G 29G 36G 37G)
Power cord - Switzerland (models 12G 13G 16G 17G 23G 24G 29G 36G 37G 66G 68G)
Power cord - Italy (models 23L 29L 11Y 12Y 14Y 17Y 18Y 21Y 23Y 25Y 29Y 32Y 11S 12S
13S 14S 16S 17S 18S 19S 21S 23S 25S 29S 32S 33S 34S 36S 34Y 36Y 67S 67Y 68S 68Y
69S 69Y 81S 81Y)
42T5050
42T5056
1
1
Power cord - Australia / New Zealand (models 14M 15M 17M 23M 24M 26M 29M 36M 39M
41M 42M 43M 45M 46M 47M 49M 51M 52M 33M 34M 63M 64M 67M 68M 81M 82M 84M)
Power cord - South Africa (models 14M 15M 17M 23M 24M 26M 29M 11A 14A 15A 17A 18A
19A 21A 23A 24A 26A 29A 12G 13G 16G 17G 23G 24G 29G 36G 37G 36M 39M 41M 42M
43M 45M 46M 47M 49M 51M 52M 33M 34M 38A 39A 41A 42A 43A 44A 45A 46A 47A 49A
51A 52A 63M 63A 64M 64A 65A 66G 67M 67A 68M 81M 81A 82M 84M)
42T5062
42T5065
42T5071
42T5077
1
1
1
1
Power cord - Israel (models 12G 13G 16G 17G 23G 24G 29G 36G 37G)
Power cord - China (PRC) (models 13C 18C 23C 29C 36C)
Power cord - Taiwan (models 21V 22V 23V 29V 34V 35V 36V )
Power cord - Korea (models 14K 17K 19K 21K 23K 24K 26K 29K 33K 34K 36K 36R 38K 39K
41K 43K 45K 46K 47K 49K 51K 52K 63K 64K 65K 67K 68K 82K 84K)
42T5083
42T4406
42T5089
1
1
1
Power cord - India (models 33Q 34Q 36Q 19Q 21Q 23Q 26Q 29Q 63Q 64Q 65Q 81Q 82Q 84Q)
Power cord - Thailand (models 63T 64T 65T 67T 68T 81T 82T 84T)
Power cord - US/Canada--optional second source (models 11S 11D 12S 12D 13S 14S 14D
16S 17S 17D 18S 18D 19S 21S 21D 23S 23D 25S 25D 29S 29D 32S 32D 23L 29L 11A
11T 14A 14T 15A 15T 17A 17T 18A 18T 19A 19T 21A 21T 23A 23T 24A 24T 26A 26T 29A
29T 17U 17F 23U 23F 26U 26F 27U 27F 28U 28F 29U 29F 31U 31F 36U 37U 36F 37F 33S
34S 36S 34D 36D 33A 34A 36A 33T 34T 36T 38A 39A 41A 42A 43A 44A 45A 46A 47A 49A
51A 52A 38T 39T 41T 43T 44T 45T 46T 47T 49T 51T 52T 61U 61F 61S 62U 63A 64A 65A
67S 67A 68S 69S 82U 82F 83U 83F 84U 84F 84A 85U 85F 86U 86F 87U 87F 88U 88F 89U
89F 54U 54F 55U 55F 56U 56F 57U 57F)
42T5096
42T5102
1
1
Power cord - Japan-optional second source (models 14J 15J 17J 19J 21J 23J 24J 26J 36E
34J 33J 36J 39J 41J 42J 43J 45J 46J 47J 49J 51J 52J 63J 64J 67J 68J 82J 84J)
Power cord - Argentina - optional second source (models 23L 29L 11Y 12Y 14Y 17Y 18Y 21Y
23Y 25Y 29Y 32Y 36L 34Y 36Y)
Chapter 9. FRU lists 111
6395 Power Cords
FRU#
CRU
42T5177
42T5114
1
1
Power cord - Brazil (new type) - optional second source (models)
Power cord - Europe (Germany) - optional second source (models 11A 14A 15A 17A 18A 19A
21A 23A 24A 26A 29A 33A 34A 36A 38A 39A 41A 42A 43A 44A 45A 46A 47A 49A 51A 52A
63A 64A 65A 67A 68A 81A 84A )
42T5120
1
Power cord - UK - optional second source (models 11A 14A 15A 17A 18A 19A 21A 23A 24A
26A 29A 12G 13G 16G 17G 23G 24G 29G 33A 34A 36A 38A 39A 41A 42A 43A 44A 45A 46A
47A 49A 51A 52A 63A 64A 65A 67A 68A 81A 84A)
42T5126
42T5129
42T5132
1
1
1
Power cord - Denmark - optional second source (models 12G 13G 16G 17G 23G 24G 29G
36G 37G)
Power cord - Switzerland - optional second source (models 12G 13G 16G 17G 23G 24G
29G 36G 37G 66G 68G )
Power cord - Italy - optional second source (models 23L 29L 11Y 12Y 14Y 17Y 18Y 21Y 23Y
25Y 29Y 32Y 11S 12S 13S 14S 16S 17S 18S 19S 21S 23S 25S 29S 32S 33S 34S 36S 34Y
36Y 67S 67Y 68S 68Y 69S 69Y 81S 81Y)
42T5135
42T5141
1
1
Power cord - Australia/New Zealand - optional second source (models 14M 15M 17M 23M
24M 26M 29M 36M 39M 41M 42M 43M 45M 46M 47M 49M 51M 52M 33M 34M 63M 64M
67M 68M 81M 82M 84M)
Power cord - South Africa - optional second source (models 14M 15M 17M 23M 24M 26M
29M 11A 14A 15A 17A 18A 19A 21A 23A 24A 26A 29A 12G 13G 16G 17G 23G 24G 29G 36G
37G 36M 39M 41M 42M 43M 45M 46M 47M 49M 51M 52M 33M 34M 38A 39A 41A 42A 43A
44A 45A 46A 47A 49A 51A 52A 63M 63A 64M 64A 65A 66G 67M 67A 68M 81M 81A 82M 84M)
42T5147
1
Power cord - Israel - optional second source (models 12G 13G 16G 17G 23G 24G 29G 36G
37G)
42T5150
42T5156
42T5162
1
1
1
Power cord - China (PRC) - optional second source (models 13C 18C 23C 29C 36C)
Power cord - Taiwan-optional second source (models 21V 22V 23V 29V 34V 35V 36V)
Power cord - Korea-optional second source (models 14K 17K 19K 21K 23K 24K 26K 29K 33K
34K 36K 36R 38K 39K 41K 43K 45K 46K 47K 49K 51K 52K 63K 64K 65K 67K 68K 82K 84K)
42T5168
42T4400
1
1
Power cord - India-optional second source (models 33Q 34Q 36Q 19Q 21Q 23Q 26Q 29Q
63Q 64Q 65Q 81Q 82Q 84Q)
Power cord - Thailand-optional second source (models 63T 64T 65T 67T 68T 81T 82T 84T )
6395 Windows XP Home Recovery CDs
FRU#
CRU
1
45R6005
45R6006
45R6007
45R6010
45R6009
45R6008
45R6014
45R6015
45R6020
45R6013
45R6018
45R6017
US/UK/AP/TH (models)
FR/CF (models)
GR (models)
IT (models)
1
1
1
1
BR (models)
1
SP/LA (models)
DK (models)
NL (models)
1
1
1
AE (models)
1
SV (models)
1
HE (models)
1
FI (models)
112 Hardware Maintenance Manual
6395 Windows XP Home Recovery CDs
FRU#
CRU
1
45R6012
45R6019
45R6030
45R6021
45R6029
45R6023
45R6016
45R6022
45R6024
45R6011
45R6025
45R6026
45R6027
45R6028
NO (models)
PL (models)
PO (models)
RU (models)
RE (models)
HU (models)
CZ (models)
TR (models)
GK (models)
Japanese (models)
1
1
1
1
1
1
1
1
1
1
Simplified Chinese (models)
Taiwan- TC (models)
Hong Kong- TC (models)
Korea (models)
1
1
1
6395 Windows XP Pro Recovery CDs
FRU#
CRU
45R5979
1
US/UK/AP/TH (models 39M 39A 39Q 41M 41A 41Q 43M 43A 43Q 45M 45A 45Q 63M 63A
63Q 82U 82M 82A 82Q 83U 84U 84M 84A 84Q 85U 86U 87U 88U 89U 54U 55U 56U 57U)
45R5980
45R5981
45R5984
45R5983
45R5982
45R5988
45R5989
45R5994
45R5987
45R5992
45R5991
45R5986
45R5993
45R6004
45R5995
45R6003
45R5997
45R5990
45R5996
45R5998
45R5985
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
FR/CF (models 82F 83F 84F 85F 86F 87F 88F 89F 54F 55F 57F 56F)
GR (models)
IT (models)
BR (models)
SP/LA (models)
DK (models)
NL (models)
AE (models)
SV (Swedish) (models)
HE (models)
FI (models)
NO (models)
PL (models)
PO (models)
RU (models)
RE (models)
HU (models)
CZ (models)
TR (models)
GK (models)
Japanese (models 39J 41J 43J 45J 63J 82J 84J)
Chapter 9. FRU lists 113
6395 Windows XP Pro Recovery CDs
FRU#
CRU
45R5999
45R6000
45R6001
45R6002
45R5977
45R5978
1
1
1
1
1
1
Simplified Chinese (models)
Taiwan-TC (models)
Hong Kong-TC (models)
Korea (models 39K 41K 43K 45K 63K 82K 84K)
Multilingual 1 XP-P -- EN, NL, FR, GR, IT (models)
Multilingual 2 XP-P -- EN, DK, FI, NO, SV (models)
6395 Vista Home Basic 32 Recovery DVDs
FRU#
CRU
1
46R7098
46R7099
46R7100
46R7101
46R7102
46R7103
46R7104
46R7105
46R7106
46R1086
46R7107
46R1088
46R1089
46R1090
46R1091
46R7108
46R1093
46R1094
46R1095
46R7109
46R7110
46R7111
46R1099
46R1100
46R1101
46R1102
46R1103
46R1104
English (models 13H)
Russian English (models)
French (models)
1
1
1
German (models)
Spanish (models)
Brazilian (models)
Italian (models)
1
1
1
1
Japanese (models)
Norwegian (models)
Swedish (models)
Danish (models)
1
1
1
1
Dutch (models)
1
Czech (models)
1
Finnish (models)
1
Polish (models)
1
Russian (models)
Turkish (models)
1
1
Hungarian (models)
Greek (models)
1
1
Simplified Chinese (models)
Taiwan (models)
1
1
Hong Kong (models)
Korea (models)
1
1
Slovenian (models)
Hebrew (models)
Portuguese (models)
Arabic Localized (models)
Slovakia (models)
1
1
1
1
114 Hardware Maintenance Manual
6395 Vista Business 32 Recovery DVDs
FRU#
CRU
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
46R7070
46R7071
46R7072
46R7073
46R7074
46R7075
46R7076
46R7077
46R7078
46R1028
46R7079
46R1030
46R1031
46R1032
46R1033
46R7080
46R1035
46R1036
46R1037
46R7081
46R7082
46R7083
46R1041
46R1042
46R1043
46R1044
46R1045
46R1046
46R1047
46R1048
English (models 15Q)
Russian (models)
French (models)
German (models)
Spanish (models 15S 15D 15Y 17S 17Y 18S 18Y)
Brazilian (models)
Italian (models)
Japanese (models)
Norwegian (models)
Swedish (models)
Danish (models)
Dutch (models)
Czech (models)
Finnish (models)
Polish (models)
Russian (models)
Turkish (models)
Hungarian (models)
Greek (models)
Simplified Chinese (models 15C)
Traditional Chinese (models)
Traditional Chinese (models)
Korean (models)
Slovenian (models)
Romanian (models)
Portuguese (models)
Serbian - Latin (models)
Slovakian (models)
Arabic Localized (models)
Hebrew (models)
6395 Vista Ultimate 32 Recovery DVDs
FRU#
CRU
46R7112
46R7113
46R7114
46R7115
46R7116
46R7117
46R7118
1
1
1
1
1
1
1
English (models)
Russian (models)
French (models)
German (models)
Spanish (models)
Brazilian (models)
Italian (models)
Chapter 9. FRU lists 115
6395 Vista Ultimate 32 Recovery DVDs
FRU#
CRU
1
46R7119
46R7120
46R1114
46R7121
46R1116
46R1117
46R1118
46R1119
46R7122
46R1121
46R1122
46R1123
46R7123
46R7124
46R7125
46R1127
46R1128
46R1129
46R1130
46R1131
46R1132
Japanese (models)
Norwegian (models)
Swedish (models)
Danish (models)
Dutch (models)
1
1
1
1
1
Czech (models)
Finnish (models)
Polish (models)
1
1
1
Russian (models)
Turkish (models)
Hungarian (models)
Greek (models)
1
1
1
1
Simplified Chinese (models)
Traditional Chinese (models)
Traditional Chinese (models)
Korean (models)
1
1
1
1
Slovenian (models)
1
Hebrew (models)
1
Portuguese (models)
Slovakian (models)
1
1
Arabic Localized (models)
6395 Vista Business 64 Recovery DVDs
FRU#
CRU
1
46R7084
46R7085
46R7086
46R7087
46R7088
46R7089
46R7090
46R7091
46R7092
46R1058
46R7093
46R1060
46R1061
46R1062
46R1063
46R7094
English (models)
Russian English (models)
French (models)
German (models)
Spanish (models)
Brazilian (models)
Italian (models)
1
1
1
1
1
1
1
Japanese (models)
Norwegian (models)
Swedish (models)
Danish (models)
Dutch (models)
1
1
1
1
1
Czech (models)
1
Finnish (models)
Polish (models)
1
1
Russian (models)
116 Hardware Maintenance Manual
6395 Vista Business 64 Recovery DVDs
FRU#
CRU
1
46R1065
46R1066
46R1067
46R7095
46R7096
46R7097
46R1071
46R1072
46R1073
46R1074
46R1075
46R1076
Turkish (models)
Hungarian (models)
Greek (models)
1
1
1
Simplified Chinese (models)
Taiwan (models)
1
1
Hong Kong (models)
Korea (models)
1
1
Slovenian (models)
Arabic Localized (models)
Hebrew (models)
1
1
1
Portuguese (models)
Slovakian (models)
1
Machine Type 6396
Item
#
6396 FRUs
FRU#
CRU
N
1
2
41R8510
40Y9034
Front audio/USB card and cable (included in Cables kit 41R8510) (models)
Hard disk drive, 80 GB 7200rpm SATA (models)
2
Chapter 9. FRU lists 117
Item
#
6396 FRUs
Hard disk drive, 160 GB 7200rpm SATA (models)
Hard disk drive, 25 GB 7200rpm SATA (models)
Hard disk drive, 320 GB 7200rpm SATA (models )
Hard disk drive, 500 GB 7200rpm SATA (models)
Hard disk drive, 750 GB 7200rpm SATA (models)
Hard disk drive, 1TB 7200rpm SATA (models CTO)
System fan (models)
FRU#
CRU
2
2
2
2
2
2
3
4
4
4
40Y9035
40Y9036
87H4891
41X5582
43C3671
45C5973
41R8511
41N3325
43C1042
42Y9353
2
2
2
2
2
2
2
2
2
2
DVD-ROM Drive - 16x/48x - SATA (models)
DVD-ROM Drive - DVD-RW/CD-RW Rambo 8 (SATA) Matrix (models)
DVD-ROM Drive - DVD-ROM/CD-RW Combo Drive - 48x/32x/48x/16x - SATA Matrix
(models)
5
5
6
7
7
8
41A9732
41A9747
41R8570
46R3849
46R3848
45C6898
1
1
Power Adapter, 120W AC/DC (models)
Power Adapter, 120W power adapter (models)
Express Card Assembly (models)
N
N
N
N
System board, Mini-ITX Intel (Q35, ICH9DO) (models)
System board, non-AMT Mini-ITX Intel (Q35, ICH9DO) (models)
Microprocessor, Intel Conroe E6750 (Core2 Duo) 2.66GHz, G-0 Stepping, 65nm,
1333MHZ FSB, 4MB L2 (models)
8
8
8
8
8
8
N
N
N
N
N
N
Microprocessor, Intel Conroe E6550 (Core2 Duo) 2.33GHz, G-0 Stepping, 65nm,
1333MHz FSB, 4MB L2 (models)
45C6899
45C6900
45C6901
45C6902
45C8499
45C8531
Microprocessor, Intel Conroe E4500 (Core2 Duo) 2.20GHz, M-0 Stepping, 65nm,
800MHz FSB, 2MB L2 (models)
Microprocessor, Intel Conroe E2160 (Pentium D) 1.8GHz, M-0 Stepping, 65nm,
800MHz FSB, 1MB L2 (models)
Microprocessor, Intel Conroe-L 440 (Celeron) 2.0GHz, A-1 Stepping, 65nm, 800MHz
FSB, 512KB L2 (models)
Microprocessor, Intel Wolfdale E8400 (Core2 Duo) 3.0GHz, C-0 Stepping, 45nm,
1333MHz FSB, 6MB L2 (models)
Microprocessor, Intel Wolfdale E8200 (Core2 Duo) 2.66GHz, C-0 Stepping, 45nm,
1333MHz FSB, 6MB L2 (models)
8
46R4261
46R4260
41R8545
43C3814
43C3815
43C6489
41R8517
41R8568
N
N
2
Microprocessor, E7200, 2.53GHz, 1066MHz FSB, 3MB L2 (models)
Microprocessor, E2200, 2.20GHz, 800MHz FSB, 1MB L2 (models)
Heat sink Intel (models)
8
9
11
11
11
12
13
2
Memory module, 512MB DDR2 PC2-5300 (667MHz) SoDIMM (models)
Memory module, 1GB DDR2 PC2-5300 (667MHz) SoDIMM (models)
Memory module, 2GB DDR2 PC2-5300 (667MHz) SoDIMM (models)
Internal speaker (models)
2
2
2
N
Media card reader (models)
The FRUs listed in the following tables are not illustrated.
118 Hardware Maintenance Manual
6396 FRUs
FRU#
CRU
2
41R8518
41R8543
41R8544
41R8548
41R8560
41R8563
Hard disk drive tray (models)
Shield kit (models)
N
N
Cable, C2 swtich/housing assembly (models)
Cable, serial (models)
N
N
USB cable (models)
N
Kit, shell (models)
6396 Keyboards (USB Preferred Pro)
FRU#
CRU
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
41A5289
41A5290
41A5291
41A5292
41A5293
41A5294
41A5295
41A5296
41A5297
41A5298
41A5299
41A5300
41A5301
41A5302
41A5303
41A5304
41A5305
41A5306
41A5307
41A5308
41A5309
41A5310
41A5311
41A5312
41A5313
41A5314
41A5315
41A5316
41A5317
41A5318
41A5319
US English (models)
Arabic (models)
Arabic/French (models)
Belgian/French (models)
Belgian/UK (models)
Brazilian (models)
Bulgarian (models)
Hong Kong/Taiwan (models)
Czech (models)
Danish (models)
Dutch (models)
French (models)
French Canadian 445 (models)
French Canadian 58 (models)
German (models)
Greek (models)
Greek/US (models)
Hebrew (models)
Hungarian (models)
Iceland (models)
Italian (models)
Japanese (models)
Korean (models)
LA Spanish (models)
Norwegian (models)
Polish (models)
Portuguese (models)
Romanian 446 (models)
Romanian 096 (models)
Russian/Cyrillic (models)
Serbian/Cyrillic (models)
Chapter 9. FRU lists 119
6396 Keyboards (USB Preferred Pro)
FRU#
CRU
41A5320
41A5321
41A5322
41A5323
41A5324
41A5325
41A5326
41A5327
41A5328
41A5329
1
1
1
1
1
1
1
1
1
1
Slovak (models)
Spanish (models )
Swedish/Finn (models)
Swiss (models)
Thailand (models)
Turkish 440 (models)
Turkish 179 (models)
UK English (models)
US European (models)
Slovenian (models)
6396 Keyboard (USB Preferred Pro Fingerprint Keyboard)
FRU#
CRU
1
41A5248
41A5249
41A5250
41A5251
41A5252
41A5253
41A5254
41A5255
41A5256
41A5257
41A5258
41A5259
41A5260
41A5261
41A5262
41A5263
41A5264
41A5265
41A5266
41A5267
41A5268
41A5269
41A5270
41A5271
41A5272
41A5273
41A5274
US (models)
1
Arabic (models)
1
Arabic/French (models)
Belgian/French (models)
Belgian/UK (models)
Brazil/Portuguese (models)
Bulgarian (models)
Chinese/US (models)
Czech (models)
1
1
1
1
1
1
1
Danish (models)
1
Dutch (models)
1
French (models)
1
French Canadian 445 (models)
French Canadian 58 (models)
German (models)
1
1
1
Greek (models)
1
Greek/US (models)
Hebrew (models)
1
1
Hungarian (models)
Iceland (models)
1
1
Italian (models)
1
Japanese (models)
Korean (models)
1
LA Spanish (models)
Norwegian (models)
Polish (models)
1
1
1
Portuguese (models)
120 Hardware Maintenance Manual
6396 Keyboard (USB Preferred Pro Fingerprint Keyboard)
Romanian 446 (models)
FRU#
CRU
1
41A5276
41A5275
41A5277
41A5278
41A5279
41A5280
41A5281
41A5282
41A5283
41A5284
41A5285
41A5286
41A5287
41A5288
1
Romanian 96 (models)
Russian/Cyrillic (models)
Serbian/Cyrillic (models)
Slovak (models)
1
1
1
1
Spanish (models)
1
Swedish/Finn (models)
Swiss, F/G (models)
Thailand (models)
1
1
1
Turkish 179 (models)
Turkish 440 (models)
UK (models)
1
1
1
US European (models)
Slovenian (models)
1
6396 mice
FRU#
CRU
41U3013
41U3030
41U3019
1
1
1
Optical wheel mouse (400DPI, USB) (models)
Optical wheel mouse (400DPI, USB) (models)
Scroll point optical mouse (800DPI, USB) (models)
6396 Adapters and miscellaneous FRUs
FRU#
CRU
39T0495
41R8522
41A5331
41A5334
89P8571
91P8835
41R4770
41R8555
2
2
1
1
1
N
2
N
Modem daughter card (MDC 1.5) kit (models)
Modem daughter card (MDC 1.5) kit Internal cable /RJ11 (models)
Lenovo branded speakers - 2 piece--primary (models)
Lenovo branded speakers - 2 piece--secondary (models)
Speaker power brick (models)
Thermal grease syringe (models)
Vertical PC stand (VPC) for blue 4.5L chassis (models)
PWR/LED cable sssembly (models)
6396 Power Cords
Power cord - US/Canada (models)
Power cord - Japan (models)
FRU#
CRU
42T5004
42T5011
42T5017
42T5174
42T5029
42T5035
42T5041
42T5044
1
1
1
1
1
1
1
1
Power cord - Argentina (models)
Power cord - Brazil (models)
Power cord - Europe (Germany) (models)
Power cord - UK (models)
Power cord - Denmark (models)
Power cord - Switzerland (models)
Chapter 9. FRU lists 121
6396 Power Cords
FRU#
CRU
1
42T5047
42T5050
42T5056
42T5062
42T5065
42T5071
42T5077
42T5083
42T4406
42T5089
42T5096
42T5102
42T5177
42T5114
42T5120
42T5126
42T5129
42T5132
42T5135
42T5141
42T5147
42T5150
42T5156
42T5162
42T5168
42T4400
Power cord - Italy (models)
1
Power cord - Australia / New Zealand (models)
Power cord - South Africa (models)
1
1
Power cord - Israel (models)
1
Power cord - China (PRC) (models)
1
Power cord - Taiwan (models)
1
Power cord - Korea (models)
1
Power cord - India (models)
1
Power cord - Thailand (models)
1
Power cord - US/Canada--optional second source (models)
Power cord - Japan-optional second source (models)
Power cord - Argentina - optional second source (models)
Power cord - Brazil (new type) - optional second source (models)
Power cord - Europe (Germany) - optional second source (models)
Power cord - UK - optional second source (models)
Power cord - Denmark - optional second source (models
Power cord - Switzerland - optional second source (models)
Power cord - Italy - optional second source (models )
Power cord - Australia/New Zealand - optional second source (models)
Power cord - South Africa - optional second source (models)
Power cord - Israel - optional second source (models)
Power cord - China (PRC) - optional second source (models)
Power cord - Taiwan-optional second source (models)
Power cord - Korea-optional second source (models)
Power cord - India-optional second source (models)
Power cord - Thailand-optional second source (models)
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
6396 Windows XP Home Recovery CDs
FRU#
CRU
45R6005
45R6006
45R6007
45R6010
45R6009
45R6008
45R6014
45R6015
45R6020
45R6013
45R6018
1
1
1
1
1
1
1
1
1
1
1
US/UK/AP/TH (models)
FR/CF (models)
GR (models)
IT (models)
BR (models)
SP/LA (models)
DK (models)
NL (models)
AE (models)
SV (models)
HE (models)
122 Hardware Maintenance Manual
6396 Windows XP Home Recovery CDs
FRU#
CRU
1
45R6017
45R6012
45R6019
45R6030
45R6021
45R6029
45R6023
45R6016
45R6022
45R6024
45R6011
45R6025
45R6026
45R6027
45R6028
FI (models)
1
NO (models)
PL (models)
PO (models)
RU (models)
RE (models)
HU (models)
CZ (models)
TR (models)
GK (models)
Japanese (models)
1
1
1
1
1
1
1
1
1
1
Simplified Chinese (models)
Taiwan-TC (models)
1
1
Hong Kong-TC (models)
Korea (models)
1
6396 Windows XP Pro Recovery CDs
FRU#
CRU
1
45R5979
45R5980
45R5981
45R5984
45R5983
45R5982
45R5988
45R5989
45R5994
45R5987
45R5992
45R5991
45R5986
45R5993
45R6004
45R5995
45R6003
45R5997
45R5990
45R5996
45R5998
45R5985
US/UK/AP/TH (models)
FR/CF (models)
GR (models)
1
1
1
IT (models)
1
BR (models)
1
SP/LA (models)
DK (models)
1
1
NL (models)
1
AE (models)
1
SV (Swedish) (models)
HE (models)
1
1
FI (models)
1
NO (models)
PL (models)
1
1
PO (models)
1
RU (models)
1
RE (models)
1
HU (models)
1
CZ (models)
1
TR (models)
1
GK (models)
1
Japanese (models)
Chapter 9. FRU lists 123
6396 Windows XP Pro Recovery CDs
FRU#
CRU
45R5999
45R6000
45R6001
45R6002
45R5977
45R5978
1
1
1
1
1
1
Simplified Chinese (models)
Taiwan-TC (models)
Hong Kong-TC (models)
Korea (models)
Multilingual 1 XP-P -- EN, NL, FR, GR, IT (models)
Multilingual 2 XP-P -- EN, DK, FI, NO, SV (models)
6396 Vista Home Basic 32 Recovery DVDs
FRU#
CRU
1
46R7098
46R7099
46R7100
46R7101
46R7102
46R7103
46R7104
46R7105
46R7106
46R1086
46R7107
46R1088
46R1089
46R1090
46R1091
46R7108
46R1093
46R1094
46R1095
46R7109
46R7110
46R7111
46R1099
46R1100
46R1101
46R1102
46R1103
46R1104
English (models 13H)
Russian English (models)
French (models)
1
1
1
German (models)
Spanish (models)
Brazilian (models)
Italian (models)
1
1
1
1
Japanese (models)
Norwegian (models)
Swedish (models)
Danish (models)
1
1
1
1
Dutch (models)
1
Czech (models)
1
Finnish (models)
1
Polish (models)
1
Russian (models)
Turkish (models)
1
1
Hungarian (models)
Greek (models)
1
1
Simplified Chinese (models)
Taiwan (models)
1
1
Hong Kong (models)
Korea (models)
1
1
Slovenian (models)
Hebrew (models)
Portuguese (models)
Arabic Localized (models)
Slovakia (models)
1
1
1
1
124 Hardware Maintenance Manual
6396 Vista Business 32 Recovery DVDs
FRU#
CRU
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
46R7070
46R7071
46R7072
46R7073
46R7074
46R7075
46R7076
46R7077
46R7078
46R1028
46R7079
46R1030
46R1031
46R1032
46R1033
46R7080
46R1035
46R1036
46R1037
46R7081
46R7082
46R7083
46R1041
46R1042
46R1043
46R1044
46R1045
46R1046
46R1047
46R1048
English (models 15Q)
Russian (models)
French (models)
German (models)
Spanish (models 15S 15D 15Y 17S 17Y 18S 18Y)
Brazilian (models)
Italian (models)
Japanese (models)
Norwegian (models)
Swedish (models)
Danish (models)
Dutch (models)
Czech (models)
Finnish (models)
Polish (models)
Russian (models)
Turkish (models)
Hungarian (models)
Greek (models)
Simplified Chinese (models 15C)
Traditional Chinese (models)
Traditional Chinese (models)
Korean (models)
Slovenian (models)
Romanian (models)
Portuguese (models)
Serbian - Latin (models)
Slovakian (models)
Arabic Localized (models)
Hebrew (models)
6396 Vista Ultimate 32 Recovery DVDs
FRU#
CRU
46R7112
46R7113
46R7114
46R7115
46R7116
46R7117
46R7118
1
1
1
1
1
1
1
English (models)
Russian (models)
French (models)
German (models)
Spanish (models)
Brazilian (models)
Italian (models)
Chapter 9. FRU lists 125
6396 Vista Ultimate 32 Recovery DVDs
FRU#
CRU
1
46R7119
46R7120
46R1114
46R7121
46R1116
46R1117
46R1118
46R1119
46R7122
46R1121
46R1122
46R1123
46R7123
46R7124
46R7125
46R1127
46R1128
46R1129
46R1130
46R1131
46R1132
Japanese (models)
Norwegian (models)
Swedish (models)
Danish (models)
Dutch (models)
1
1
1
1
1
Czech (models)
Finnish (models)
Polish (models)
1
1
1
Russian (models)
Turkish (models)
Hungarian (models)
Greek (models)
1
1
1
1
Simplified Chinese (models)
Traditional Chinese (models)
Traditional Chinese (models)
Korean (models)
1
1
1
1
Slovenian (models)
1
Hebrew (models)
1
Portuguese (models)
Slovakian (models)
1
1
Arabic Localized (models)
6396 Vista Business 64 Recovery DVDs
FRU#
CRU
1
46R7084
46R7085
46R7086
46R7087
46R7088
46R7089
46R7090
46R7091
46R7092
46R1058
46R7093
46R1060
46R1061
46R1062
46R1063
46R7094
English (models)
Russian English (models)
French (models)
German (models)
Spanish (models)
Brazilian (models)
Italian (models)
1
1
1
1
1
1
1
Japanese (models)
Norwegian (models)
Swedish (models)
Danish (models)
Dutch (models)
1
1
1
1
1
Czech (models)
1
Finnish (models)
Polish (models)
1
1
Russian (models)
126 Hardware Maintenance Manual
6396 Vista Business 64 Recovery DVDs
FRU#
CRU
1
46R1065
46R1066
46R1067
46R7095
46R7096
46R7097
46R1071
46R1072
46R1073
46R1074
46R1075
46R1076
Turkish (models)
Hungarian (models)
Greek (models)
1
1
1
Simplified Chinese (models)
Taiwan (models)
1
1
Hong Kong (models)
Korea (models)
1
1
Slovenian (models)
Arabic Localized (models)
Hebrew (models)
1
1
1
Portuguese (models)
Slovakian (models)
1
Machine Type 6397
Item
#
6397 FRUs
FRU#
CRU
N
1
2
41R8510
40Y9034
Front audio/USB card and cable (included in Cables kit 41R8510) (all models)
Hard disk drive, 80 GB 7200rpm SATA (models)
2
Chapter 9. FRU lists 127
Item
#
6397 FRUs
FRU#
CRU
2
40Y9035
2
Hard disk drive, 160 GB 7200rpm SATA (models 11U 11F 11S 11L 11D 11Y 11G 11M
11A 11Q 11T 11C 11B 11H 11V 11K 11R 11E 11J)
2
2
2
2
2
3
4
40Y9036
87H4891
41X5582
43C3671
45C5973
41R8511
41N3325
2
2
2
2
2
2
2
Hard disk drive, 25 GB 7200rpm SATA (models)
Hard disk drive, 320 GB 7200rpm SATA (models )
Hard disk drive, 500 GB 7200rpm SATA (models)
Hard disk drive, 750 GB 7200rpm SATA (models)
Hard disk drive, 1TB 7200rpm SATA (models CTO)
System fan (all models)
DVD-ROM Drive - 16x/48x - SATA (models 11U 11F 11S 11L 11D 11Y 11G 11M 11A
11Q 11T 11C 11B 11H 11V 11K 11R 11E 11J)
4
4
2
2
DVD-ROM Drive - DVD-RW/CD-RW Rambo 8 (SATA) Matrix (models)
43C1042
42Y9353
DVD-ROM Drive - DVD-ROM/CD-RW Combo Drive - 48x/32x/48x/16x - SATA Matrix
(models)
5
41A9732
1
Power adapter, 120W AC/DC (models 11U 11F 11S 11L 11D 11Y 11G 11M 11A 11Q
11T 11C 11B 11H 11V 11K 11R 11E 11J)
5
6
7
41A9747
41R8570
46R3849
1
N
N
Power adapter, 120W power adapter (models)
Express card assembly (all models)
System board, Mini-ITX Intel (Q35, ICH9DO) (models 11U 11F 11S 11L 11D 11Y 11G
11M 11A 11Q 11T 11C 11B 11H 11V 11K 11R 11E 11J)
7
8
46R3848
45C6898
N
N
System board, non-AMT Mini-ITX Intel (Q35, ICH9DO) (models)
Microprocessor, Intel Conroe E6750 (Core2 Duo) 2.66GHz, G-0 Stepping, 65nm,
1333MHZ FSB, 4MB L2 (models)
8
8
8
8
8
8
N
N
N
N
N
N
Microprocessor, Intel Conroe E6550 (Core2 Duo) 2.33GHz, G-0 Stepping, 65nm,
1333MHz FSB, 4MB L2 (models)
45C6899
45C6900
45C6901
45C6902
45C8499
45C8531
Microprocessor, Intel Conroe E4500 (Core2 Duo) 2.20GHz, M-0 Stepping, 65nm,
800MHz FSB, 2MB L2 (models)
Microprocessor, Intel Conroe E2160 (Pentium D) 1.8GHz, M-0 Stepping, 65nm,
800MHz FSB, 1MB L2 (models)
Microprocessor, Intel Conroe-L 440 (Celeron) 2.0GHz, A-1 Stepping, 65nm, 800MHz
FSB, 512KB L2 (models)
Microprocessor, Intel Wolfdale E8400 (Core2 Duo) 3.0GHz, C-0 Stepping, 45nm,
1333MHz FSB, 6MB L2 (models)
Microprocessor, Intel Wolfdale E8200 (Core2 Duo) 2.66GHz, C-0 Stepping, 45nm,
1333MHz FSB, 6MB L2 (models 11U 11F 11S 11L 11D 11Y 11G 11M 11A 11Q 11T
11C 11B 11H 11V 11K 11R 11E 11J)
8
8
46R4261
46R4260
41R8545
43C3814
43C3815
43C6489
N
N
2
2
2
2
Microprocessor, E7200, 2.53GHz, 1066MHz FSB, 3MB L2 (models)
Microprocessor, E2200, 2.20GHz, 800MHz FSB, 1MB L2 (models)
Heat sink Intel (all models)
9
11
11
11
Memory module, 512MB DDR2 PC2-5300 (667MHz) SoDIMM (all models)
Memory module, 1GB DDR2 PC2-5300 (667MHz) SoDIMM (models)
Memory module, 2GB DDR2 PC2-5300 (667MHz) SoDIMM (models 11U 11F 11S 11L
11D 11Y 11G 11M 11A 11Q 11T 11C 11B 11H 11V 11K 11R 11E 11J)
128 Hardware Maintenance Manual
Item
#
6397 FRUs
FRU#
CRU
2
12
13
41R8517
41R8568
Internal speaker (all models)
Media card reader (all models)
N
The FRUs listed in the following tables are not illustrated.
6397 FRUs
Hard disk drive tray (all models)
Shield kit (all models)
FRU#
CRU
2
41R8518
41R8543
41R8544
41R8548
41R8560
41R8563
41R8555
N
N
Cable, C2 swtich/housing assembly (all models)
Cable, serial (all models)
N
N
USB cable (all models)
N
Kit, shell (all models)
N
PWR/LED cable assembly (all models)
6397 Keyboards (USB Preferred Pro)
US English (models 11U 11G 11M 11A 11Q 11H 11R 11E)
Arabic (models)
FRU#
CRU
1
41A5289
41A5290
41A5291
41A5292
41A5293
41A5294
41A5295
41A5296
41A5297
41A5298
41A5299
41A5300
41A5301
41A5302
41A5303
41A5304
41A5305
41A5306
41A5307
41A5308
41A5309
41A5310
41A5311
41A5312
1
1
Arabic/French (models 11G)
Belgian/French (models 11G)
Belgian/UK (models 11G)
Brazilian (models)
1
1
1
1
Bulgarian (models 11G)
1
Hong Kong/Taiwan (models 11B 11V)
Czech (models 11G )
1
1
Danish (models 11G)
1
Dutch (models 11G )
1
French (models 11G)
1
French Canadian 445 (models 11F)
French Canadian 58 (models 11F)
German (models 11G)
1
1
1
Greek (models 11G )
1
Greek/US (models 11G )
1
Hebrew (models 11G)
1
Hungarian (models 11G)
1
Iceland (models 11G)
1
Italian (models 11G)
1
Japanese (models 11K)
1
Korean (models 11J)
1
LA Spanish (models 11S 11D 11Y)
Chapter 9. FRU lists 129
6397 Keyboards (USB Preferred Pro)
FRU#
CRU
1
41A5313
41A5314
41A5315
41A5316
41A5317
41A5318
41A5319
41A5320
41A5321
41A5322
41A5323
41A5324
41A5325
41A5326
41A5327
41A5328
41A5329
Norwegian (models 11G)
Polish (models 11G)
1
1
Portuguese (models 11G)
1
Romanian 446 (models 11G)
Romanian 096 (models 11G)
Russian/Cyrillic (models 11G)
Serbian/Cyrillic (models 11G)
Slovak (models 11G)
1
1
1
1
1
Spanish (models 11G)
1
Swedish/Finn (models 11G)
Swiss (models 11G)
1
1
Thailand (models 11T)
1
Turkish 440 (models 11G)
Turkish 179 (models 11G)
UK English (models 11G)
US European (models 11G)
Slovenian (models 11G)
1
1
1
1
6397 Keyboard (USB Preferred Pro Fingerprint Keyboard)
FRU#
CRU
1
41A5248
41A5249
41A5250
41A5251
41A5252
41A5253
41A5254
41A5255
41A5256
41A5257
41A5258
41A5259
41A5260
41A5261
41A5262
41A5263
41A5264
41A5265
41A5266
41A5267
US (models)
1
Arabic (models)
1
Arabic/French (models)
Belgian/French (models)
Belgian/UK (models)
Brazil/Portuguese (models)
Bulgarian (models)
Chinese/US (models)
Czech (models)
1
1
1
1
1
1
1
Danish (models)
1
Dutch (models)
1
French (models)
1
French Canadian 445 (models)
French Canadian 58 (models)
German (models)
1
1
1
Greek (models)
1
Greek/US (models)
Hebrew (models)
1
1
Hungarian (models)
Iceland (models)
1
130 Hardware Maintenance Manual
6397 Keyboard (USB Preferred Pro Fingerprint Keyboard)
FRU#
CRU
41A5268
41A5269
41A5270
41A5271
41A5272
41A5273
41A5274
41A5276
41A5275
41A5277
41A5278
41A5279
41A5280
41A5281
41A5282
41A5283
41A5284
41A5285
41A5286
41A5287
41A5288
1
1
1
Italian (models)
Japanese (models)
Korean (models)
LA Spanish (models)
Norwegian (models)
Polish (models)
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Portuguese (models)
Romanian 446 (models)
Romanian 96 (models)
Russian/Cyrillic (models)
Serbian/Cyrillic (models)
Slovak (models)
Spanish (models)
Swedish/Finn (models)
Swiss, F/G (models)
Thailand (models)
Turkish 179 (models)
Turkish 440 (models)
UK (models)
US European (models)
Slovenian (models)
6397 mice
FRU#
CRU
41U3013
1
Optical wheel mouse (400DPI, USB) (models 11U 11F 11S 11L 11D 11Y 11G 11M 11A 11Q
11T 11C 11B 11H 11V 11K 11R 11E 11J)
41U3030
41U3019
1
1
Optical wheel mouse (400DPI, USB) (models 11U 11F 11S 11L 11D 11Y 11G 11M 11A 11Q
11T 11C 11B 11H 11V 11K 11R 11E 11J)
Scroll point optical mouse (800DPI, USB) (models)
6397 Adapters and miscellaneous FRUs
Modem daughter card (MDC 1.5) kit (models)
FRU#
CRU
39T0495
41R8522
41A5331
41A5334
89P8571
91P8835
41R4770
2
2
1
1
1
N
2
Modem daughter card (MDC 1.5) kit internal cable/RJ11 (models)
Lenovo branded speakers - 2 piece--primary (models)
Lenovo branded speakers - 2 piece--secondary (models)
Speaker power brick (models)
Thermal grease syringe (models)
Vertical PC stand (VPC) for blue 4.5L chassis (models)
Chapter 9. FRU lists 131
6397 Power Cords
Power cord - US/Canada (models 11U 11F 11S 11D 11L 11A 11T)
Power cord - Japan (models 11J)
FRU#
CRU
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
42T5004
42T5011
42T5017
42T5174
42T5029
42T5035
42T5041
42T5044
42T5047
42T5050
42T5056
42T5062
42T5065
42T5071
42T5077
42T5083
42T4406
42T5089
42T5096
42T5102
42T5177
42T5114
42T5120
42T5126
42T5129
42T5132
42T5135
42T5141
42T5147
42T5150
42T5156
42T5162
42T5168
42T4400
Power cord - Argentina (models 11Y 11L)
Power cord - Brazil (models)
Power cord - Europe (Germany) (models 11A)
Power cord - UK (models 11G 11A)
Power cord - Denmark (models 11G)
Power cord - Switzerland (models 11G)
Power cord - Italy (models 11S 11Y 11L 11G)
Power cord - Australia / New Zealand (models 11M)
Power cord - South Africa (models 11M )
Power cord - Israel (models 11G)
Power cord - China (PRC) (models 11C)
Power cord - Taiwan (models 11V)
Power cord - Korea (models 11K)
Power cord - India (models 11Q)
Power cord - Thailand (models)
Power cord - US/Canada--optional second source (models 11U 11F 11S 11D 11L 11A 11T )
Power cord - Japan-optional second source (models 11J)
Power cord - Argentina - optional second source (models 11Y 11L)
Power cord - Brazil (new type) - optional second source (models)
Power cord - Europe (Germany) - optional second source (models 11A)
Power cord - UK - optional second source (models 11G 11A)
Power cord - Denmark - optional second source (models 11G )
Power cord - Switzerland - optional second source (models 11G)
Power cord - Italy - optional second source (models 11S 11Y 11L 11G)
Power cord - Australia/New Zealand - optional second source (models 11M)
Power cord - South Africa - optional second source (models 11M)
Power cord - Israel - optional second source (models 11G)
Power cord - China (PRC) - optional second source (models 11C)
Power cord - Taiwan-optional second source (models 11V)
Power cord - Korea-optional second source (models 11K)
Power cord - India-optional second source (models 11Q)
Power cord - Thailand-optional second source (models)
6397 Windows XP Home Recovery CDs
FRU#
CRU
45R6005
45R6006
45R6007
1
1
1
US/UK/AP/TH (models)
FR/CF (models)
GR (models)
132 Hardware Maintenance Manual
6397 Windows XP Home Recovery CDs
FRU#
CRU
1
45R6010
45R6009
45R6008
45R6014
45R6015
45R6020
45R6013
45R6018
45R6017
45R6012
45R6019
45R6030
45R6021
45R6029
45R6023
45R6016
45R6022
45R6024
45R6011
45R6025
45R6026
45R6027
45R6028
IT (models)
1
BR (models)
SP/LA (models)
DK (models)
NL (models)
AE (models)
SV (models)
HE (models)
FI (models)
1
1
1
1
1
1
1
1
NO (models)
PL (models)
PO (models)
RU (models)
RE (models)
HU (models)
CZ (models)
TR (models)
GK (models)
Japanese (models)
1
1
1
1
1
1
1
1
1
1
Simplified Chinese (models)
Taiwan-TC (models)
1
1
Hong Kong-TC (models)
Korea (models)
1
6397 Windows XP Pro Recovery CDs
FRU#
CRU
1
45R5979
45R5980
45R5981
45R5984
45R5983
45R5982
45R5988
45R5989
45R5994
45R5987
45R5992
45R5991
45R5986
45R5993
US/UK/AP/TH (models)
FR/CF (models)
GR (models)
1
1
1
IT (models)
1
BR (models)
1
SP/LA (models)
DK (models)
1
1
NL (models)
1
AE (models)
1
SV (Swedish) (models)
HE (models)
1
1
FI (models)
1
NO (models)
1
PL (models)
Chapter 9. FRU lists 133
6397 Windows XP Pro Recovery CDs
FRU#
CRU
1
45R6004
45R5995
45R6003
45R5997
45R5990
45R5996
45R5998
45R5985
45R5999
45R6000
45R6001
45R6002
45R5977
45R5978
PO (models)
1
RU (models)
1
RE (models)
1
HU (models)
1
CZ (models)
1
TR (models)
1
GK (models)
1
Japanese (models)
Simplified Chinese (models)
Taiwan-TC (models)
Hong Kong-TC (models)
Korea (models)
1
1
1
1
1
Multilingual 1 XP-P -- EN, NL, FR, GR, IT (models)
Multilingual 2 XP-P -- EN, DK, FI, NO, SV (models)
1
6397 Vista Home Basic 32 Recovery DVDs
FRU#
CRU
1
46R7098
46R7099
46R7100
46R7101
46R7102
46R7103
46R7104
46R7105
46R7106
46R1086
46R7107
46R1088
46R1089
46R1090
46R1091
46R7108
46R1093
46R1094
46R1095
46R7109
46R7110
46R7111
46R1099
English (models 13H)
Russian English (models)
French (models)
1
1
1
German (models)
Spanish (models)
Brazilian (models)
Italian (models)
1
1
1
1
Japanese (models)
Norwegian (models)
Swedish (models)
Danish (models)
1
1
1
1
Dutch (models)
1
Czech (models)
1
Finnish (models)
Polish (models)
1
1
Russian (models)
Turkish (models)
1
1
Hungarian (models)
Greek (models)
1
1
Simplified Chinese (models)
Taiwan (models)
1
1
Hong Kong (models)
Korea (models)
1
134 Hardware Maintenance Manual
6397 Vista Home Basic 32 Recovery DVDs
FRU#
CRU
46R1100
46R1101
46R1102
46R1103
46R1104
1
1
1
1
1
Slovenian (models)
Hebrew (models)
Portuguese (models)
Arabic Localized (models)
Slovakia (models)
6397 Vista Business 32 Recovery DVDs
FRU#
CRU
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
46R7070
46R7071
46R7072
46R7073
46R7074
46R7075
46R7076
46R7077
46R7078
46R1028
46R7079
46R1030
46R1031
46R1032
46R1033
46R7080
46R1035
46R1036
46R1037
46R7081
46R7082
46R7083
46R1041
46R1042
46R1043
46R1044
46R1045
46R1046
46R1047
46R1048
English (models 15Q)
Russian (models)
French (models)
German (models)
Spanish (models 15S 15D 15Y 17S 17Y 18S 18Y)
Brazilian (models)
Italian (models)
Japanese (models)
Norwegian (models)
Swedish (models)
Danish (models)
Dutch (models)
Czech (models)
Finnish (models)
Polish (models)
Russian (models)
Turkish (models)
Hungarian (models)
Greek (models)
Simplified Chinese (models 15C)
Traditional Chinese (models)
Traditional Chinese (models)
Korean (models)
Slovenian (models)
Romanian (models)
Portuguese (models)
Serbian - Latin (models)
Slovakian (models)
Arabic Localized (models)
Hebrew (models)
Chapter 9. FRU lists 135
6397 Vista Ultimate 32 Recovery DVDs
FRU#
CRU
1
46R7112
46R7113
46R7114
46R7115
46R7116
46R7117
46R7118
46R7119
46R7120
46R1114
46R7121
46R1116
46R1117
46R1118
46R1119
46R7122
46R1121
46R1122
46R1123
46R7123
46R7124
46R7125
46R1127
46R1128
46R1129
46R1130
46R1131
46R1132
English (models)
Russian (models)
French (models)
German (models)
Spanish (models)
Brazilian (models)
Italian (models)
1
1
1
1
1
1
1
Japanese (models)
Norwegian (models)
Swedish (models)
Danish (models)
Dutch (models)
1
1
1
1
1
Czech (models)
Finnish (models)
Polish (models)
1
1
1
Russian (models)
Turkish (models)
Hungarian (models)
Greek (models)
1
1
1
1
Simplified Chinese (models)
Traditional Chinese (models)
Traditional Chinese (models)
Korean (models)
1
1
1
1
Slovenian (models)
1
Hebrew (models)
1
Portuguese (models)
Slovakian (models)
1
1
Arabic Localized (models)
6397 Vista Business 64 Recovery DVDs
FRU#
CRU
46R7084
46R7085
46R7086
46R7087
46R7088
46R7089
46R7090
46R7091
46R7092
1
1
1
1
1
1
1
1
1
English (models)
Russian English (models)
French (models)
German (models)
Spanish (models)
Brazilian (models)
Italian (models)
Japanese (models)
Norwegian (models)
136 Hardware Maintenance Manual
6397 Vista Business 64 Recovery DVDs
FRU#
CRU
1
46R1058
46R7093
46R1060
46R1061
46R1062
46R1063
46R7094
46R1065
46R1066
46R1067
46R7095
46R7096
46R7097
46R1071
46R1072
46R1073
46R1074
46R1075
46R1076
Swedish (models)
Danish (models)
Dutch (models)
Czech (models)
Finnish (models)
Polish (models)
Russian (models)
Turkish (models)
Hungarian (models)
Greek (models)
1
1
1
1
1
1
1
1
1
1
Simplified Chinese (models)
Taiwan (models)
1
1
Hong Kong (models)
Korea (models)
1
1
Slovenian (models)
Arabic Localized (models)
Hebrew (models)
1
1
1
Portuguese (models)
Slovakian (models)
1
Chapter 9. FRU lists 137
138 Hardware Maintenance Manual
Chapter 10. Additional Service Information
This chapter provides additional information that the service representative might find helpful.
Security features
Security features in this section include the following:
• Passwords
• Vital Product Data
• Management Information Format (MIF)
Hardware controlled Passwords
Hardware controlled passwords are set using the Setup Utility program. For more information about
Operating system password
An operating system password is very similar to a power-on password and denies access to the computer
by an unauthorized user when the password is activated. The computer is unusable until the password is
entered and recognized by the computer.
Vital product data
Each computer has a unique Vital Product Data (VPD) code stored in the nonvolatile memory on the system
board. After you replace the system board, the VPD must be updated. To update the VPD, see “Updating
BIOS levels
An incorrect level of BIOS can cause false errors and unnecessary FRU replacement. Use the following
information to determine the current level of BIOS installed in the computer, the latest BIOS available for the
computer, and where to obtain the latest level of BIOS.
• To determine the current Level of BIOS:
– Start the Setup Utility.
– Select System Information on the Main setup screen.
• Sources for obtaining the latest level BIOS available
1. Lenovo support web site: http://www.lenovo.com/support/
2. Lenovo Customer Support Center
3. Levels 1 and 2 Support
Updating (flashing) BIOS from a CD-ROM or diskette
This section describes how to update (flash) the BIOS using a CD-ROM or diskette. system program updates
are available athttp://www.lenovo.com/support on the World Wide Web.
1. To update (flash) the BIOS:
© Copyright Lenovo 2005, 2010
139
• If using a CD-ROM, make sure the computer is turned on. Insert the system program update (flash)
CD-ROM into the optical drive. The update begins.
• If using a diskette, make sure the computer is turned off. Insert the system program update (flash)
diskette and turn on the computer. The update begins.
2. When you are prompted to select a language, press the number on your keyboard that corresponds to
the language and then press Enter.
3. When prompted to change the serial number, press Y.
4. Type the seven-character serial number of your computer and then press Enter.
5. When prompted to change the machine type/model, press Y.
6. Type the seven-character machine type/model of your computer and then press Enter.
7. Follow the instructions on the screen to complete the update.
Recovering from a POST/BIOS update failure
Attention
If an interruption occurs during a POST/BIOS update (flash update), the computer might not restart correctly.
If this occurs, perform the following procedure commonly called Boot-block Recovery.
Note: If your computer has no internal diskette drive, an optional USB diskette drive must be connected to
use the BIOS flash diskette.
1. Turn off the computer and any attached devices, such as printers, monitors, and external drives.
2. Unplug all power cords from electrical outlets, and open the computer cover. See “Opening the cover”
on page 68.
page 68.
4. Remove any cables that impede access to the Clear CMOS/Recovery jumper.
5. Move the jumper from the standard position (pins 1 and 2) to pins 2 and 3.
6. Insert the POST/BIOS update (flash) diskette in the diskette drive.
7. Close the computer cover and reconnect any cables that were disconnected.
8. Reconnect the power cords for the computer and monitor to electrical outlets.
9. Turn on the computer and the monitor.
10.The recovery session will take two to three minutes. During this time, you will hear a series of beeps.
After the update session is completed, the series of beeps ends. There will be no video, and the system
will automatically turn off.
11.Open the computer cover, and move the Clear CMOS/Recovery jumper back to the original positions
(pins 1 and 2).
12.Remove the POST/BIOS flash diskette from the diskette drive.
13.Close the computer cover and reconnect any cables that were disconnected.
14.Turn on the computer to restart the operating system.
Power management
Power management reduces the power consumption of certain components of the computer such as the
system power supply, processor, hard disk drives, and some monitors.
140 Hardware Maintenance Manual
Automatic configuration and power interface (ACPI) BIOS
Being an ACPI BIOS system, the operating system is allowed to control the power management features
of the computer and the setting for Advanced Power Management (APM) BIOS mode is ignored. Not
all operating systems support ACPI BIOS mode.
Automatic Power-On features
The Automatic Power-On features within the Power Management menu allow you to enable and disable
features that turn on the computer automatically.
• RTC resume: You can specify a date and time at which the computer will be turned on automatically.
This can be either a single event or a daily event.
• Wake on LAN: If the computer has a properly configured token-ring or Ethernet LAN adapter card that is
Wake on LAN-enabled and there is remote network management software, you can use the Wake on LAN
feature. When you set Wake on LAN to Enabled, the computer will turn on when it receives a specific
signal from another computer on the local area network (LAN).
Chapter 10. Additional Service Information 141
142 Hardware Maintenance Manual
Appendix A. Notices
Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult
your local Lenovo representative for information on the products and services currently available in your
area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that
Lenovo product, program, or service may be used. Any functionally equivalent product, program, or service
that does not infringe any Lenovo intellectual property right may be used instead. However, it is the user's
responsibility to evaluate and verify the operation of any other product, program, or service.
Lenovo may have patents or pending patent applications covering subject matter described in this
document. The furnishing of this document does not give you any license to these patents. You can send
license inquiries, in writing, to:
Lenovo (United States), Inc.
1009 Think Place - Building One
Morrisville, NC 27560
U.S.A.
Attention: Lenovo Director of Licensing
LENOVO PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some jurisdictions do not allow
disclaimer of express or implied warranties in certain transactions, therefore, this statement may not apply
to you.
This information could include technical inaccuracies or typographical errors. Changes are periodically
made to the information herein; these changes will be incorporated in new editions of the publication.
Lenovo may make improvements and/or changes in the product(s) and/or the program(s) described in this
publication at any time without notice.
The products described in this document are not intended for use in implantation or other life support
applications where malfunction may result in injury or death to persons. The information contained in this
document does not affect or change Lenovo product specifications or warranties. Nothing in this document
shall operate as an express or implied license or indemnity under the intellectual property rights of Lenovo
or third parties. All information contained in this document was obtained in specific environments and is
presented as an illustration. The result obtained in other operating environments may vary.
Lenovo may use or distribute any of the information you supply in any way it believes appropriate without
incurring any obligation to you.
Any references in this publication to non-Lenovo Web sites are provided for convenience only and do not in
any manner serve as an endorsement of those Web sites. The materials at those Web sites are not part of
the materials for this Lenovo product, and use of those Web sites is at your own risk.
Any performance data contained herein was determined in a controlled environment. Therefore, the result
obtained in other operating environments may vary significantly. Some measurements may have been
made on development-level systems and there is no guarantee that these measurements will be the same
on generally available systems. Furthermore, some measurements may have been estimated through
extrapolation. Actual results may vary. Users of this document should verify the applicable data for their
specific environment.
© Copyright Lenovo 2005, 2010
143
Television output notice
The following notice applies to models that have the factory-installed television-output feature.
This product incorporates copyright protection technology that is protected by method claims of certain U.S.
patents and other intellectual property rights owned by Macrovision Corporation and other rights owners.
Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended
for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation.
Reverse engineering or disassembly is prohibited.
Trademarks
The following terms are trademarks of Lenovo in the United States, other countries, or both:
Lenovo
ThinkCentre
Rescue and Recovery
The following terms are trademarks of International Business Machines Corporation in the United States,
other countries, or both:
IBM (used under license)
Wake on LAN
Intel, Core, and Pentium are trademarks of Intel Corporation in the United States, other countries, or both.
Microsoft, Windows, and Windows Vista are trademarks of the Microsoft group of companies.
Other company, product, or service names may be trademarks or service marks of others.
144 Hardware Maintenance Manual
Part Number: 43C6257
Printed in USA
(1P) P/N: 43C6257
*43C6257*
|