ThinkStation
Hardware Maintenance Manual
Machine Types: 4223, 4228 and 4229
ThinkStation
Hardware Maintenance Manual
Machine Types: 4223, 4228 and 4229
Note: Before using this information and the product it supports, be sure to read and understand the Chapter
First Edition (April 2012)
© Copyright Lenovo 2012.
LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant a General Services Administration
“GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925.
Contents
1
43
43
Configuring SATA or SAS RAID functionality
General safety .
Electrical safety .
Voltage-selection switch .
Safety inspection guide .
3
3
5
5
44
45
46
Handling electrostatic discharge-sensitive
47
47
devices
6
6
6
Grounding requirements .
Safety notices (multi-lingual translations)
Deleting RAID volumes using the LSI
48
48
Specifications .
Lenovo ThinkVantage Tools
Lenovo Solution Center .
Lenovo Welcome.
29
29
30
30
30
30
30
31
49
49
49
50
51
53
Power Supply Problems .
Beep symptoms .
Additional information resources
Miscellaneous error messages
Undetermined problems .
33
55
Locating connectors on the rear of your
Lenovo Solution Center .
35
computer .
Locating major FRUs and CRUs .
56
56
58
58
61
Locating parts on the system board
37
37
37
38
38
38
38
38
Viewing and changing settings
Using passwords.
Handling static-sensitive devices
Installing external options
Removing the computer cover.
63
63
63
64
65
66
69
72
75
77
78
80
81
Setting, changing, and deleting a password
Removing and reinstalling the front bezel
Installing or replacing a PCI card .
CMOS) .
Enabling or disabling a device
39
39
39
40
Installing or replacing the optical drive
Replacing the card reader
Selecting or changing the startup device
sequence .
Enabling ErP compliance mode and Deep Sx
Replacing the hard disk drive fan assembly
Replacing the rear fan assembly .
40
40
41
Exiting the Setup Utility program
© Copyright Lenovo 2012
iii
Installing or replacing a hard disk drive
Installing or replacing a hard disk drive
83
87
105
105
Updating (flashing) the BIOS from a disc.
Updating (flashing) the BIOS from your
enablement module .
Replacing the front audio and USB
operating system .
Recovering from a POST/BIOS update failure
Power management
106
106
107
assembly .
88
89
90
99
102
104
Replacing the internal speaker.
Replacing the system board
(ACPI) BIOS .
107
107
107
Replacing the power supply assembly
European conformance CE mark
110
110
110
Security features .
105
105
105
105
105
iv ThinkStation Hardware Maintenance Manual
Chapter 1. About this manual
This manual provides service and reference information for ThinkStation® computers listed on the front cover.
This manual is intended only for trained service personnel who are familiar with Lenovo® computer products.
Before servicing a Lenovo computer product, be sure to read Chapter 2 “Safety information” on page 3.
105 are not specific to any machine type. These chapters are applicable to all ThinkStation computers.
For major Field Replaceable Unit (FRU) locations and Customer Replaceable Unit (CRU) identification,
For FRU part numbers, go to:
Important Safety Information
Be sure to read all caution and danger statements in this book before performing any of the instructions.
Veuillez lire toutes les consignes de type DANGER et ATTENTION du présent document avant d'exécuter
les instructions.
Lesen Sie unbedingt alle Hinweise vom Typ "ACHTUNG" oder "VORSICHT" in dieser Dokumentation, bevor
Sie irgendwelche Vorgänge durchführen
Leggere le istruzioni introdotte da ATTENZIONE e PERICOLO presenti nel manuale prima di eseguire una
qualsiasi delle istruzioni
Certifique-se de ler todas as instruções de cuidado e perigo neste manual antes de executar qualquer
uma das instruções
Es importante que lea todas las declaraciones de precaución y de peligro de este manual antes de seguir
las instrucciones.
© Copyright Lenovo 2012
1
2
ThinkStation Hardware Maintenance Manual
Chapter 2. Safety information
This chapter contains the safety information that you need to be familiar with before servicing a computer.
General safety
Follow these rules to ensure general safety:
• Observe good housekeeping in the area of the machines during and after maintenance.
• When lifting any heavy object:
1. Ensure you can stand safely without slipping.
2. Distribute the weight of the object equally between your feet.
3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift.
4. Lift by standing or by pushing up with your leg muscles; this action removes the strain from the
muscles in your back. Do not attempt to lift any objects that weigh more than 16 kg (35 lb) or objects
that you think are too heavy for you.
• Do not perform any action that causes hazards to the customer, or that makes the equipment unsafe.
• Before you start the machine, ensure that other service representatives and the customer's personnel are
not in a hazardous position.
• Place removed covers and other parts in a safe place, away from all personnel, while you are servicing
the machine.
• Keep your tool case away from walk areas so that other people will not trip over it.
• Do not wear loose clothing that can be trapped in the moving parts of a machine. Ensure that your sleeves
are fastened or rolled up above your elbows. If your hair is long, fasten it.
• Insert the ends of your necktie or scarf inside clothing or fasten it with a nonconductive clip, approximately
8 centimeters (3 inches) from the end.
• Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for your clothing.
Remember: Metal objects are good electrical conductors.
• Wear safety glasses when you are: hammering, drilling, soldering, cutting wire, attaching springs, using
solvents, or working in any other conditions that might be hazardous to your eyes.
• After service, reinstall all safety shields, guards, labels, and ground wires. Replace any safety device
that is worn or defective.
• Reinstall all covers correctly before returning the machine to the customer.
Electrical safety
CAUTION:
Electrical current from power, telephone, and communication cables can be hazardous. To avoid
personal injury or equipment damage, disconnect the attached power cords, telecommunication
systems, networks, and modems before you open the server/workstation covers, unless instructed
otherwise in the installation and configuration procedures.
Observe the following rules when working on electrical equipment.
© Copyright Lenovo 2012
3
Important: Use only approved tools and test equipment. Some hand tools have handles covered with a soft
material that does not insulate you when working with live electrical currents. Many customers have, near
their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges.
Do not use this type of mat to protect yourself from an electric shock.
• Find the room emergency power-off (EPO) switch, disconnecting switch, or electrical outlet. If an electrical
accident occurs, you can then operate the switch or unplug the power cord quickly.
• Do not work alone under hazardous conditions or near equipment that has hazardous voltages.
• Disconnect all power before:
– Performing a mechanical inspection
– Working near power supplies
– Removing or installing FRU
• Before you start to work on the machine, unplug the power cord. If you cannot unplug it, ask the customer
to power-off the wall box that supplies power to the machine and to lock the wall box in the off position.
• If you need to work on a machine that has exposed electrical circuits, observe the following precautions:
– Ensure that another person, familiar with the power-off controls, is near you.
Remember: Another person must be there to switch off the power, if necessary.
– Use only one hand when working with powered-on electrical equipment; keep the other hand in your
pocket or behind your back.
Remember: There must be a complete circuit to cause an electric shock. By observing the above
rule, you may prevent a current from passing through your body.
– When using a tester, set the controls correctly and use the approved probe leads and accessories for
that tester.
– Stand on suitable rubber mats (obtained locally, if necessary) to insulate you from grounds such as
metal floor strips and machine frames.
Observe the special safety precautions when you work with very high voltages; these instructions are in
the safety sections of maintenance information. Use extreme care when measuring high voltages.
• Regularly inspect and maintain your electrical hand tools for safe operational condition.
• Do not use worn or broken tools and testers.
• Never assume that power has been disconnected from a circuit. First, check that it has been powered-off.
• Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors,
nongrounded power extension cables, power surges, and missing safety grounds.
• Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is
conductive; such touching can cause personal injury and machine damage.
• Do not service the following parts with the power on when they are removed from their normal operating
places in a machine:
– Power supply units
– Pumps
– Blowers and fans
– Motor generators
and similar units. (This practice ensures correct grounding of the units.)
• If an electrical accident occurs:
– Use caution; do not become a victim yourself.
– Switch off power.
– Send another person to get medical aid.
4
ThinkStation Hardware Maintenance Manual
Voltage-selection switch
Some computers are equipped with a voltage-selection switch located near the power-cord connection
point on the computer and some computers do not have a voltage-selection switch. Before you install
your computer or relocate your computer to another country or region, you must be certain that you have
matched your computer to the voltage available at your electrical outlet.
CAUTION:
You must know the voltage of the electrical connection (outlet) where your computer will be
connected. If you do not know the voltage, contact your local electric company or refer to official
Web sites or other literature for travelers to the country or region where you are located.
If your computer has a voltage-selection switch, you must set the switch to match the voltage available at
your electrical outlet. Setting the voltage-selection switch incorrectly will cause the computer to malfunction
and might cause permanent damage to the computer. Do not connect the computer to an electrical
outlet until you have verified that the voltage-selection switch setting matches the voltage available at the
electrical outlets.
If your computer does not have a voltage-selection switch, inspect the voltage-rating label on the bottom of
the computer and note the following:
• If the voltage-rating label shows a range of either “100-127 V” or “200-240 V,” you must ensure that the
voltage provided at the electrical outlet matches the voltage rating on the computer label. If it does
not match, do not attempt to connect the computer to the electrical outlet, unless an external device
such as a voltage-converting transformer is used.
• If the voltage-rating label shows a dual range of “100-127 V” and “200-240 V,” this signifies that the
computer is suitable for worldwide operation and the computer will automatically adjust to the voltage at
the electrical outlet regardless of the country or region where the computer is being connected.
Safety inspection guide
The intent of this inspection guide is to assist you in identifying potentially unsafe conditions on these
products. Each machine, as it was designed and built, had required safety items installed to protect users
and service personnel from injury. This guide addresses only those items. However, good judgment should
be used to identify potential safety hazards due to attachment of features or options not covered by this
inspection guide.
If any unsafe conditions are present, you must determine how serious the apparent hazard could be and
whether you can continue without first correcting the problem.
Consider these conditions and the safety hazards they present:
• Electrical hazards, especially primary power (primary voltage on the frame can cause serious or fatal
electrical shock).
• Explosive hazards, such as a damaged CRT face or bulging capacitor
• Mechanical hazards, such as loose or missing hardware
The guide consists of a series of steps presented in a checklist. Begin the checks with the power off, and
the power cord disconnected.
Checklist:
1. Check exterior covers for damage (loose, broken, or sharp edges).
2. Power-off the computer. Disconnect the power cord.
Chapter 2. Safety information
5
3. Check the power cord for:
a. A third-wire ground connector in good condition. Use a meter to measure third-wire ground
continuity for 0.1 ohm or less between the external ground pin and frame ground.
b. The power cord should be the appropriate type as specified in the parts listings.
c. Insulation must not be frayed or worn.
4. Remove the cover.
5. Check for any obvious alterations. Use good judgment as to the safety of any alterations.
6. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or
other liquids, or signs of fire or smoke damage.
7. Check for worn, frayed, or pinched cables.
8. Check that the power-supply cover fasteners (screws or rivets) have not been removed or tampered with.
Handling electrostatic discharge-sensitive devices
Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to
electrostatic discharge (ESD). ESD damage can occur when there is a difference in charge between objects.
Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the
person handling the part are all at the same charge.
Notes:
1. Use product-specific ESD procedures when they exceed the requirements noted here.
2. Make sure that the ESD protective devices you use have been certified (ISO 9000) as fully effective.
When handling ESD-sensitive parts:
• Keep the parts in protective packages until they are inserted into the product.
• Avoid contact with other people while handling the part.
• Wear a grounded wrist strap against your skin to eliminate static on your body.
• Prevent the part from touching your clothing. Most clothing is insulative and retains a charge even when
you are wearing a wrist strap.
• Use the black side of a grounded work mat to provide a static-free work surface. The mat is especially
useful when handling ESD-sensitive devices.
• Select a grounding system, such as those listed below, to provide protection that meets the specific
service requirement.
Note: The use of a grounding system is desirable but not required to protect against ESD damage.
– Attach the ESD ground clip to any frame ground, ground braid, or green-wire ground.
– Use an ESD common ground or reference point when working on a double-insulated or
battery-operated system. You can use coax or connector-outside shells on these systems.
– Use the round ground-prong of the ac plug on ac-operated computers.
Grounding requirements
Electrical grounding of the computer is required for operator safety and correct system function. Proper
grounding of the electrical outlet can be verified by a certified electrician.
Safety notices (multi-lingual translations)
The caution and danger safety notices in this section are provided in the following languages:
6
ThinkStation Hardware Maintenance Manual
• English
• Arabic
• Brazilian/Portuguese
• Chinese (simplified)
• Chinese (traditional)
• French
• German
• Hebrew
• Italian
• Korean
• Spanish
DANGER
Electrical current from power, telephone and communication cables is hazardous.
To avoid a shock hazard:
• Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration
of this product during an electrical storm.
• Connect all power cords to a properly wired and grounded electrical outlet.
• Connect to properly wired outlets any equipment that will be attached to this product.
• When possible, use one hand only to connect or disconnect signal cables.
• Never turn on any equipment when there is evidence of fire, water, or structural damage.
• Disconnect the attached power cords, telecommunications systems, networks, and modems
before you open the device covers, unless instructed otherwise in the installation and configuration
procedures.
• Connect and disconnect cables as described in the following tables when installing, moving, or
opening covers on this product or attached devices.
To Connect
To Disconnect
1. Turn everything OFF.
1. Turn everything OFF.
2. First, attach all cables to devices.
3. Attach signal cables to connectors.
4. Attach power cords to outlet.
5. Turn device ON.
2. First, remove power cords from outlet.
3. Remove signal cables from connectors.
4. Remove all cables from devices.
CAUTION:
When replacing the lithium battery, use only Part Number 45C1566 or an equivalent type battery
recommended by the manufacturer. If your system has a module containing a lithium battery, replace
Chapter 2. Safety information
7
it only with the same module type made by the same manufacturer. The battery contains lithium and
can explode if not properly used, handled, or disposed of. Do not:
• Throw or immerse into water
• Heat to more than 100°C (212°F)
• Repair or disassemble
Dispose of the battery as required by local ordinances or regulations.
CAUTION:
When laser products (such as CD-ROMs, DVD-ROM drives, fiber optic devices, or transmitters) are
installed, note the following:
• Do not remove the covers. Removing the covers of the laser product could result in exposure to
hazardous laser radiation. There are no serviceable parts inside the device.
• Use of controls or adjustments or performance of procedures other than those specified herein
might result in hazardous radiation exposure.
DANGER
Some laser products contain an embedded Class 3A or Class 3B laser diode. Note the following:
Laser radiation when open. Do not stare into the beam, do not view directly with optical
instruments, and avoid direct exposure to the beam.
≥18 kg (37 lbs)
≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs)
CAUTION:
Use safe practices when lifting.
CAUTION:
The power control button on the device and the power switch on the power supply do not turn off
the electrical current supplied to the device. The device also might have more than one power
cord. To remove all electrical current from the device, ensure that all power cords are disconnected
from the power source.
8
ThinkStation Hardware Maintenance Manual
2
1
Chapter 2. Safety information
9
≥18 kg (37 lbs)
≥32 kg (70.5 lbs)
≥55 kg (121.2 lbs)
10 ThinkStation Hardware Maintenance Manual
2
1
PERIGO
A corrente elétrica proveniente de cabos de alimentação, de telefone e de comunicações é perigosa.
Para evitar risco de choque elétrico:
• Não conecte nem desconecte nenhum cabo ou execute instalação, manutenção ou reconfiguração
deste produto durante uma tempestade com raios.
• Conecte todos os cabos de alimentação a tomadas elétricas corretamente instaladas e aterradas.
• Todo equipamento que for conectado a este produto deve ser conectado a tomadas corretamente
instaladas.
• Quando possível, utilize apenas uma das mãos para conectar ou desconectar cabos de sinal.
• Nunca ligue nenhum equipamento quando houver evidência de fogo, água ou danos estruturais.
• Antes de abrir tampas de dispositivos, desconecte cabos de alimentação, sistemas de telecomunicação,
redes e modems conectados, a menos que especificado de maneira diferente nos procedimentos de
instalação e configuração.
• Conecte e desconecte os cabos conforme descrito na tabela apresentada a seguir ao instalar, mover ou
abrir tampas deste produto ou de dispositivos conectados.
Para Conectar:
Para Desconectar:
1. DESLIGUE Tudo.
1. DESLIGUE Tudo.
2. Primeiramente, conecte todos os cabos aos
dispositivos.
2. Primeiramente, remova os cabos de alimentação das
tomadas.
3. Conecte os cabos de sinal aos conectores.
4. Conecte os cabos de alimentação às tomadas.
5. LIGUE os dispositivos.
3. Remova os cabos de sinal dos conectores.
4. Remova todos os cabos dos dispositivos.
CUIDADO:
Ao substituir a bateria de lítio, utilize apenas uma bateria com Número de Peça 45C1566 ou um tipo
de bateria equivalente recomendado pelo Se o seu sistema possui um módulo com uma bateria de
lítio, substitua-o apenas por um módulo do mesmo tipo e do mesmo fabricante. A bateria contém lítio
e pode explodir se não for utilizada, manuseada ou descartada de maneira correta.
Chapter 2. Safety information 11
Não:
• Jogue ou coloque na água
• Aqueça a mais de 100°C (212°F)
• Conserte nem desmonte
Descarte a bateria conforme requerido pelas leis ou regulamentos locais.
PRECAUCIÓN:
Quando produtos a laser (como unidades de CD-ROMs, unidades de DVD-ROM, dispositivos de fibra ótica
ou transmissores) estiverem instalados, observe o seguinte:
• Não remova as tampas. A remoção das tampas de um produto a laser pode resultar em exposição
prejudicial à radiação de laser. Não existem peças que podem ser consertadas no interior do dispositivo.
• A utilização de controles ou ajustes ou a execução de procedimentos diferentes dos especificados aqui
pode resultar em exposição prejudicial à radiação.
PERIGO
Alguns produtos a laser contêm diodo de laser integrado da Classe 3A ou da Classe 3B. Observe o seguinte:
Radiação a laser quando aberto. Não olhe diretamente para o feixe a olho nu ou com instrumentos ópticos e
evite exposição direta ao feixe.
≥18 kg (37 lbs)
≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs)
CUIDADO:
Utilize procedimentos de segurança para levantar equipamentos.
CUIDADO:
O botão de controle de alimentação do dispositivo e o botão para ligar/desligar da fonte de alimentação
não desligam a corrente elétrica fornecida ao dispositivo. O dispositivo também pode ter mais de um cabo
de alimentação. Para remover toda a corrente elétrica do dispositivo, assegure que todos os cabos de
alimentação estejam desconectados da fonte de alimentação.
12 ThinkStation Hardware Maintenance Manual
2
1
Chapter 2. Safety information 13
2
1
14 ThinkStation Hardware Maintenance Manual
Chapter 2. Safety information 15
2
1
DANGER
Le courant électrique provenant de l'alimentation, du téléphone et des câbles de transmission peut présenter
un danger.
Pour éviter tout risque de choc électrique :
• Ne manipulez aucun câble et n'effectuez aucune opération d'installation, d'entretien ou de reconfiguration
de ce produit au cours d'un orage.
• Branchez tous les cordons d'alimentation sur un socle de prise de courant correctement câblé et mis à la
terre.
• Branchez sur des socles de prise de courant correctement câblés tout équipement connecté à ce produit.
• Lorsque cela est possible, n'utilisez qu'une seule main pour connecter ou déconnecter les câbles
d'interface.
• Ne mettez jamais un équipement sous tension en cas d'incendie ou d'inondation, ou en présence de
dommages matériels.
• Avant de retirer les carters de l'unité, mettez celle-ci hors tension et déconnectez ses cordons
d'alimentation, ainsi que les câbles qui la relient aux réseaux, aux systèmes de télécommunication et aux
modems (sauf instruction contraire mentionnée dans les procédures d'installation et de configuration).
• Lorsque vous installez, que vous déplacez, ou que vous manipulez le présent produit ou des périphériques
qui lui sont raccordés, reportez-vous aux instructions ci-dessous pour connecter et déconnecter les
différents cordons.
16 ThinkStation Hardware Maintenance Manual
Connexion
Déconnexion
1. Mettez les unités HORS TENSION.
1. Mettez les unités HORS TENSION.
2. Commencez par brancher tous les cordons sur les
unités.
2. Débranchez les cordons d'alimentation des prises.
3. Débranchez les câbles d'interface des connecteurs.
4. Débranchez tous les câbles des unités.
3. Branchez les câbles d'interface sur des connecteurs.
4. Branchez les cordons d'alimentation sur des prises.
5. Mettez les unités SOUS TENSION.
ATTENTION:
Remplacer la pile au lithium usagée par une pile de référence identique exclusivement, (référence
45C1566), ou suivre les instructions du fabricant qui en définit les équivalences. Si votre système est
doté d'un module contenant une pile au lithium, vous devez le remplacer uniquement par un module
identique, produit par le même fabricant. La pile contient du lithium et peut exploser en cas de
mauvaise utilisation, de mauvaise manipulation ou de mise au rebut inappropriée.
Ne pas :
• la jeter à l'eau,
• l'exposer à des températures supérieures à 100°C,
• chercher à la réparer ou à la démonter.
Ne pas mettre la pile à la poubelle. Pour la mise au rebut, se reporter à la réglementation en vigueur.
ATTENTION:
Si des produits à laser (tels que des unités de CD-ROM, de DVD-ROM, des unités à fibres optiques, ou
des émetteurs) sont installés, prenez connaissance des informations suivantes :
• Ne retirez pas le carter. En ouvrant l'unité de CD-ROM ou de DVD-ROM, vous vous exposez au
rayonnement dangereux du laser. Aucune pièce de l'unité n'est réparable.
• Pour éviter tout risque d'exposition au rayon laser, respectez les consignes de réglage et
d'utilisation des commandes, ainsi que les procédures décrites dans le présent manuel.
DANGER
Certains produits à laser contiennent une diode à laser intégrée de classe 3A ou 3B. Prenez
connaissance des informations suivantes:
Rayonnement laser lorsque le carter est ouvert. Evitez toute expositiondirecte au rayon laser. Evitez
de regarder fixement le faisceau ou del'observer à l'aide d'instruments optiques.
Chapter 2. Safety information 17
≥18 kg (37 lbs)
≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs)
ATTENTION:
Soulevez la machine avec précaution.
ATTENTION:
L'interrupteur de contrôle d'alimentation de l'unité et l'interrupteur dubloc d'alimentation ne coupent
pas le courant électrique alimentantl'unité. En outre, le système peut être équipé de plusieurs
cordonsd'alimentation. Pour mettre l'unité hors tension, vous devez déconnectertous les cordons
de la source d'alimentation.
2
1
VORSICHT
An Netz-, Telefon- und Datenleitungen können gefährliche Spannungen anliegen.
Aus Sicherheitsgründen:
• Bei Gewitter an diesem Gerät keine Kabel anschließen oder lösen. Ferner keine Installations-,
Wartungs- oder Rekonfigurationsarbeiten durchführen.
• Gerät nur an eine Schutzkontaktsteckdose mit ordnungsgemäß geerdetem Schutzkontakt
anschließen.
• Alle angeschlossenen Geräte ebenfalls an Schutzkontaktsteckdosen mit ordnungsgemäß
geerdetem Schutzkontakt anschließen.
• Die Signalkabel nach Möglichkeit einhändig anschließen oder lösen, um einen Stromschlag durch
Berühren von Oberflächen mit unterschiedlichem elektrischem Potenzial zu vermeiden.
• Geräte niemals einschalten, wenn Hinweise auf Feuer, Wasser oder Gebäudeschäden vorliegen.
18 ThinkStation Hardware Maintenance Manual
• Die Verbindung zu den angeschlossenen Netzkabeln, Telekommunikationssystemen, Netzwerken
und Modems ist vor dem Öffnen des Gehäuses zu unterbrechen, sofern in den Installations- und
Konfigurationsprozeduren keine anders lautenden Anweisungen enthalten sind.
• Zum Installieren, Transportieren und Öffnen der Abdeckungen des Computers oder der
angeschlossenen Einheiten die Kabel gemäß der folgenden Tabelle anschließen und abziehen.
Zum Anschließen der Kabel gehen Sie wie folgt vor
Zum Abziehen der Kabel gehen Sie wie folgt vor
1. Schalten Sie alle Einheiten AUS.
1. Schalten Sie alle Einheiten AUS.
2. Schließen Sie erst alle Kabel an die Einheiten an.
3. Schließen Sie die Signalkabel an die Buchsen an.
4. Schließen Sie die Netzkabel an die Steckdose an.
5. Schalten Sie die Einheit EIN.
2. Ziehen Sie zuerst alle Netzkabel aus den
Netzsteckdosen.
3. Ziehen Sie die Signalkabel aus den Buchsen.
4. Ziehen Sie alle Kabel von den Einheiten ab.
CAUTION:
Eine verbrauchte Lithiumbatterie nur durch eine Batterie mit der Teilenummer 45C1566 oder eine
gleichwertige, vom Hersteller empfohlene Batterie ersetzen. Enthält das System ein Modul mit einer
Lithiumbatterie, dieses nur durch ein Modul desselben Typs und von demselben Hersteller ersetzen.
Die Batterie enthält Lithium und kann bei unsachgemäßer Verwendung, Handhabung oder Entsorgung
explodieren.
Die Batterie nicht:
• mit Wasser in Berührung bringen.
• über 100 C erhitzen.
• reparieren oder zerlegen.
Die örtlichen Bestimmungen für die Entsorgung von Sondermüll beachten.
ACHTUNG:
Bei der Installation von Lasergeräten (wie CD-ROM-Laufwerken, DVD- aufwerken, Einheiten mit
Lichtwellenleitertechnik oder Sendern) Folgendes beachten:
• Die Abdeckungen nicht entfernen. Durch Entfernen der Abdeckungen des Lasergeräts können
gefährliche Laserstrahlungen freigesetzt werden. Das Gerät enthält keine zu wartenden Teile.
• Werden Steuerelemente, Einstellungen oder Durchführungen von Prozeduren anders als hier
angegeben verwendet, kann gefährliche Laserstrahlung auftreten.
VORSICHT
Einige Lasergeräte enthalten eine Laserdiode der Klasse 3A oder 3B. Beachten Sie Folgendes:
Chapter 2. Safety information 19
Laserstrahlung bei geöffneter Verkleidung. Nicht in den Strahl blicken. Keine Lupen oder Spiegel
verwenden. Strahlungsbereich meiden.
≥18 kg (37 lbs)
≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs)
ACHTUNG:
Arbeitsschutzrichtlinien beim Anheben der Maschine beachten.
ACHTUNG:
Mit dem Netzschalter an der Einheit und am Netzteil wird die Stromversorgung für die Einheit
nicht unterbrochen. Die Einheit kann auch mit mehreren Netzkabeln ausgestattet sein. Um die
Stromversorgung für die Einheit vollständig zu unterbrechen, müssen alle zum Gerät führenden
Netzkabel vom Netz getrennt werden.
2
1
20 ThinkStation Hardware Maintenance Manual
Chapter 2. Safety information 21
2
1
PERICOLO
La corrente elettrica proveniente dai cavi di alimentazione, del telefono e di comunicazione può essere
pericolosa.
Per evitare il rischio di scosse elettriche:
• Non collegare o scollegare qualsiasi cavo oppure effettuare l'installazione, la manutenzione o la
riconfigurazione del prodotto durante un temporale.
• Collegare tutti i fili elettrici a una presa di alimentazione correttamente cablata e dotata di messa a
terra.
• Collegare alle prese elettriche appropriate tutte le apparecchiature che verranno utilizzate per
questo prodotto.
22 ThinkStation Hardware Maintenance Manual
• Se possibile, utilizzare solo una mano per collegare o scollegare i cavi di segnale.
• Non accendere assolutamente apparecchiature in presenza di incendi, perdite d'acqua o danno
strutturale.
• Scollegare i cavi di alimentazione, i sistemi di telecomunicazione, le reti e il modem prima di
aprire i coperchi del dispositivo, salvo istruzioni contrarie relative alle procedure di installazione e
configurazione.
• Collegare e scollegare i cavi come descritto nella seguente tabella quando vengono effettuate
operazioni di installazione, spostamento o apertura dei coperchi di questo prodotto o delle unità
collegate.
Per collegarsi
Per scollegarsi
1. SPEGNERE le apparecchiature.
2. Innanzitutto, collegare tutti i cavi alle unità.
3. Collegare i cavi di segnale ai connettori.
4. Collegare i cavi di alimentazione alla presa.
5. Accendere l'unità.
1. SPEGNERE le apparecchiature.
2. Innanzitutto, rimuovere i cavi di alimentazione dalla
presa.
3. Rimuovere i cavi di segnale dai connettori.
4. Rimuovere tutti i cavi dalle unità.
ATTENZIONE:
Quando si sostituisce la batteria al litio, utilizzare solo il Numero parte 45C1566 o un tipo di batteria
equivalente consigliato dal produttore. Se sul sistema è presente un modulo che contiene una batteria
al litio, sostituirlo solo con un tipo di modulo dello stesso tipo della stessa casa di produzione. La
batteria contiene litio e può esplodere se usata, maneggiata o smaltita in modo non corretto.
Non:
• Gettare o immergere la batteria nell'acqua
• Riscaldarla ad una temperatura superiore ai 100 gradi C (212 gradi F)
• Smontarla, ricaricarla o tentare di ripararla
Le batterie usate vanno smaltite in accordo alla normativa in vigore (DPR 915/82 e successive
disposizioni e disposizioni locali).
ATTENZIONE:
Quando vengono installati prodotti laser (quali CD-ROM, unità DVD-ROM, unità a fibre ottiche o
trasmittenti), tener presente quanto segue:
• Non rimuovere gli sportelli. L'apertura di un'unità laser può determinare l'esposizione a radiazioni
laser pericolose. All'interno dell'unità non vi sono parti su cui effettuare l'assistenza tecnica.
• L'utilizzo di controlli, regolazioni o l'esecuzione di procedure non descritti nel presente manuale
possono provocare l'esposizione a radiazioni pericolose.
Chapter 2. Safety information 23
PERICOLO
Alcune unità laser contengono un diodo laser di Classe 3A o Classe 3B. Tener presente quanto segue:
Aprendo l'unità vengono emesse radiazioni laser. Non fissare il fascio, non guardarlo direttamente
con strumenti ottici ed evitare l'esposizione al fascio.
≥18 kg (37 lbs)
≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs)
ATTENZIONE:
Prestare attenzione nel sollevare l'apparecchiatura.
ATTENZIONE:
Il pulsante di controllo dell'alimentazione presente sull'unità e l'interruttore dell'alimentatore non
disattivano l'alimentazione corrente fornita all'unità. E' possibile che l'unità disponga di più cavi di
alimentazione. Per disattivare l'alimentazione dall'unità, accertarsi che tutti i cavi di alimentazione
siano scollegati dalla fonte di alimentazione.
2
1
24 ThinkStation Hardware Maintenance Manual
Chapter 2. Safety information 25
2
1
PELIGRO
La corriente eléctrica procedente de cables de alimentación, teléfonos y cables de comunicación puede
ser peligrosa.
Para evitar el riesgo de descarga eléctrica:
• No conecte ni desconecte los cables ni realice ninguna tarea de instalación, mantenimiento o
reconfiguración de este producto durante una tormenta eléctrica.
• Conecte todos los cables de alimentación a tomas de corriente debidamente cableadas y
conectadas a tierra.
• Cualquier equipo que se conecte a este producto también debe conectarse a tomas de corriente
debidamente cableadas.
• Siempre que sea posible, utilice una sola mano para conectar o desconectar los cables de señal.
• No encienda nunca un equipo cuando hay señales de fuego, agua o daños estructurales.
26 ThinkStation Hardware Maintenance Manual
• Desconecte los cables de alimentación, los sistemas de telecomunicaciones, las redes y los
módems conectados antes de abrir las cubiertas de los dispositivos, a menos que se indique lo
contrario en los procedimientos de instalación y configuración.
• Conecte y desconecte los cables, como se describe en la tabla siguiente, cuando instale, mueva o
abra las cubiertas de este producto o de los dispositivos conectados.
Para conectar
Para desconectar
1. APÁGUELO todo.
1. APÁGUELO todo.
2. En primer lugar, conecte todos los cables a los
dispositivos.
2. En primer lugar, desenchufe los cables de alimentación
de las tomas de corriente.
3. Conecte los cables de señal a los conectores.
3. Desconecte los cables de señal de los conectores.
4. Desconecte todos los cables de los dispositivos.
4. Enchufe los cables de alimentación a las tomas de
corriente.
5. Encienda el dispositivo.
PRECAUCIÓN:
Cuando sustituya una batería de litio, utilice solamente una batería número de pieza 45C1566 u otra
de tipo equivalente recomendada por el fabricante. Si su sistema dispone de un módulo que contiene
una batería de litio, reemplácelo sólo con el mismo tipo de módulo, del mismo fabricante. La batería
contiene litio y puede explotar si no se utiliza, manipula o desecha correctamente.
No debe:
• Arrojarla al agua o sumergirla en ella
• Exponerla a temperaturas superiores a 100°C (212°F)
• Repararla o desmontarla
Deshágase de la batería según especifiquen las leyes o normas locales.
PRECAUCIÓN:
Cuando haya productos láser (como unidades de CD-ROM, unidades de DVD, dispositivos de fibra
óptica o transmisores) instalados, tenga en cuenta lo siguiente:
• No quite las cubiertas. Si quita las cubiertas del producto láser, podría quedar expuesto a radiación
láser peligrosa. Dentro del dispositivo no existe ninguna pieza que requiera servicio técnico.
• Si usa controles o ajustes o realiza procedimientos que no sean los especificados aquí, podría
exponerse a radiaciones peligrosas.
PELIGRO
Chapter 2. Safety information 27
Algunos productos láser tienen incorporado un diodo láser de clase 3A o clase 3B. Tenga en cuenta lo
siguiente:
Cuando se abre, queda expuesto a radiación láser. No mire directamente al rayo láser, ni siquiera con
instrumentos ópticos, y evite exponerse directamente al rayo láser.
≥18 kg (37 lbs)
≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs)
PRECAUCIÓN:
Adopte procedimientos seguros al levantar el equipo.
PRECAUCIÓN:
El botón de control de alimentación del dispositivo y el interruptor de alimentación de la fuente de
alimentación no desconectan la corriente eléctrica suministrada al dispositivo. Además, el dispositivo
podría tener más de un cable de alimentación. Para suprimir toda la corriente eléctrica del dispositivo,
asegúrese de que todos los cables de alimentación estén desconectados de la toma de corriente.
2
1
28 ThinkStation Hardware Maintenance Manual
Chapter 3. General information
This chapter provides general information that applies to all machine types supported by this publication.
Specifications
This section lists the physical specifications for your computer.
Dimensions
Width: 210 mm (8.3 inches)
Height: 485 mm (19.1 inches) (floor to top of handle)
Depth: 602 mm (23.7 inches)
Weight
Maximum configuration as shipped: 27.5 kg (60.5 lbs)
Environment
• Air temperature:
Operating: 10°C to 35°C (50°F to 95°F)
Storage: -40°C to 60°C (-40°F to 140°F) in original shipping package
Storage: -10°C to 60°C (14°F to 140°F) without package
Note: The allowable upper temperature limit decreases by 1°C (1.8°F) for every 300 m (1000 ft) above sea level.
• Humidity:
Operating: 10% to 80% (non-condensing) (10% per hour)
Storage: 10% to 90% (non-condensing) (10% per hour)
• Altitude:
Supported altitude: (unpressurized): –50 to 10 000ft (–15.2 to 3 048 m)
Electrical input
• Input voltage:
– Low range:
Minimum: 100 V ac
Maximum: 127 V ac
Input frequency range: 50 to 60 Hz
– High range:
Minimum: 200 V ac
Maximum: 240 V ac
Input frequency range: 50 to 60 Hz
Lenovo ThinkVantage Tools
The Lenovo ThinkVantage® Tools program guides you to a host of information sources and provides easy
access to various tools to help you work more easily and securely.
To access the Lenovo ThinkVantage Tools program, click Start ➙ All Programs ➙ Lenovo ThinkVantage
Tools.
© Copyright Lenovo 2012
29
The following table lists the programs that you can access from the Lenovo ThinkVantage Tools program. To
access a program, double-click the corresponding icon.
Table 1. Program icon names in Lenovo ThinkVantage Tools
Program name
Create Recovery Media
Icon name in Lenovo ThinkVantage Tools
Factory Recovery Disks
Lenovo Solution Center
SimpleTap
System Health and Diagnostics
SimpleTap
ThinkVantage Rescue and Recovery®
Enhanced Backup and Restore
Lenovo Solution Center
The Lenovo Solution Center program enables you to troubleshoot and resolve computer problems. It
combines diagnostic tests, system information collection, security status, and support information, along
with hints and tips for maximum system performance. See “Lenovo Solution Center” on page 35 for detailed
information.
Lenovo Welcome
The Lenovo Welcome program introduces some innovative built-in features of Lenovo to you and guides you
through some important setup tasks to help you make the most of your computer.
Note: The Lenovo Welcome program is only available on computers preinstalled with the Windows 7
operating system from Lenovo.
Product Recovery
The Product Recovery program enables you to restore the contents of the hard disk drive to the factory
default settings.
SimpleTap
The SimpleTap program provides you with a quick way to customize some basic computer settings such as
muting the speakers, adjusting the volume, locking the computer operating system, launching a program,
opening a Web page, opening a file, and so on. You also can use the SimpleTap program to access the
Lenovo App Shop, from which you can download various applications and computer software.
To start the SimpleTap program in a quick way, do any of the following:
• Click the red SimpleTap launch point on the desktop. The red launch point is available on the desktop
after you have launched the SimpleTap program for the first time.
• Press the blue ThinkVantage button if your keyboard has one.
Note: The SimpleTap program is only available on certain models preinstalled with the Windows 7 operating
system. If your Windows 7 model is not preinstalled with the SimpleTap program, you can download it
ThinkVantage Rescue and Recovery
The ThinkVantage Rescue and Recovery program is a one button recovery and restore solution that includes
a set of self-recovery tools to help you diagnose computer problems, get help, and recover from system
crashes, even if you cannot start the Windows operating system.
30 ThinkStation Hardware Maintenance Manual
Note: If the Enhanced Backup and Restore icon in the Lenovo ThinkVantage Tools program is dimmed, it
indicates that you need to install the ThinkVantage Rescue and Recovery program manually before enabling
its features. To install the ThinkVantage Rescue and Recovery program, do the following:
1. Click Start ➙ All Programs ➙ Lenovo ThinkVantage Tools, and double-click Enhanced Backup
and Restore.
2. Follow the instructions on the screen.
3. When the installation process completes, the Enhanced Backup and Restore icon is activated.
Additional information resources
If you have Internet access, the most up-to-date information for your computer is available at:
http://www.lenovo.com/support
You can find the following information:
• Customer Replaceable Unit (CRU) installation or replacement instructions
• Downloads and drivers
• Parts information
• Publications
• Troubleshooting information
• Links to other useful sources of information
Chapter 3. General information 31
32 ThinkStation Hardware Maintenance Manual
Chapter 4. General Checkout
Attention
The drives in the computer you are servicing might have been rearranged or the drive startup sequence might
have been changed. Be extremely careful during write operations such as copying, saving, or formatting.
Data or programs can be overwritten if you select an incorrect drive.
General error messages appear if a problem or conflict is found by an application program, the operating
system, or both. For an explanation of these messages, refer to the information supplied with that software
package.
Before replacing a FRU, ensure that the latest level of BIOS is installed on the system. A down-level BIOS
might cause false errors and unnecessary replacement of the system board. For more information on how to
Use the following procedure to help determine the cause of a problem:
1. Turn off the computer and all external devices.
2. Check all cables and power cords.
3. Set all display controls to the middle position.
4. Turn on all external devices.
5. Turn on the computer.
• Look for displayed error codes
• Listen for beep codes
• Look for readable instructions or a main menu on the display.
If you did not receive the correct response, proceed to step 6 on page 33.
If you do receive the correct response, proceed to step 7 on page 33.
6. Look at the following conditions and follow the instructions:
• If the computer hangs and no error is displayed, continue at step 7 on page 33.
• If the test stops and you cannot continue, replace the last device tested.
Problem determination tips
Due to the variety of hardware and software combinations that can be encountered, use the following
information to assist you in problem determination. If possible, have this information available when
requesting assistance from Service Support and Engineering functions.
• Machine type and model
• Processor or hard disk drive upgrades
• Failure symptom
– Do diagnostics indicate a failure?
– What, when, where, single, or multiple systems?
– Is the failure repeatable?
– Has this configuration ever worked?
© Copyright Lenovo 2012
33
– If it has been working, what changes were made prior to it failing?
– Is this the original reported failure?
• Diagnostics version
– Type and version level
• Hardware configuration
– Print (print screen) configuration currently in use
– BIOS level
• Operating system software
– Type and version level
Notes: To eliminate confusion, identical systems are considered identical only if they:
1. Are the exact machine type and models
2. Have the same BIOS level
3. Have the same adapters/attachments in the same locations
4. Have the same address jumpers/terminators/cabling
5. Have the same software versions and levels
6. Have the same diagnostic diskettes (version)
7. Have the same configuration options set in the system
8. Have the same setup for operating-system-controlled files
Comparing the configuration and software set-up between “working and non-working” systems will often
lead to problem resolution.
34 ThinkStation Hardware Maintenance Manual
Chapter 5. Diagnostics
The diagnostic program is used to test hardware components of your computer. The diagnostic program can
also report operating-system-controlled settings that interfere with the correct operation of your computer.
You can use the preinstalled diagnostic program to diagnose computer problems, if your computer is
running the Windows operating system.
Notes:
1. Your computer is preinstalled with the Lenovo Solution Center program for diagnostic purposes. For
2. If you are unable to isolate and repair the problem yourself after running the diagnostic program, save
and print the log files created by the diagnostic program. You will need the log files when you speak to a
Lenovo technical support representative.
Lenovo Solution Center
The Lenovo Solution Center program enables you to troubleshoot and resolve computer problems. It
combines diagnostic tests, system information collection, security status, and support information, along
with hints and tips for maximum system performance.
Notes:
• The Lenovo Solution Center program is available only on models preinstalled with the Windows 7
• If you are using the Windows Vista® or Windows XP operating system, go to
To run the Lenovo Solution Center program on the Windows 7 operating system, click Start ➙ All Programs
➙ Lenovo ThinkVantage Tools ➙ System Health and Diagnostics. Follow the instructions on the screen.
For additional information, refer to the Lenovo Solution Center help system.
Note: If you are unable to isolate and repair the problem yourself after running the program, save and print
the log files created by the program. You will need the log files when you speak to a Lenovo technical
support representative.
© Copyright Lenovo 2012
35
36 ThinkStation Hardware Maintenance Manual
Chapter 6. Using the Setup Utility program
The Setup Utility program is used to view and change the configuration settings of your computer, regardless
of which operating system you are using. However, the operating system settings might override any similar
settings in the Setup Utility program.
Starting the Setup Utility program
To start the Setup Utility program, do the following:
1. Make sure your computer is turned off.
2. Repeatedly press and release the F1 key when turning on the computer. When you hear multiple
beeps or see a logo screen, release the F1 key.
Note: If a Power-On Password or an Administrator Password has been set, the Setup Utility program
menu will not be displayed until you type the correct password. For more information, see “Using
When the POST detects that the hard disk drive has been removed from your computer or the memory
module size has decreased, an error message will be displayed when you start the computer and you will be
prompted to do one of the following:
• Press F1 to enter the Setup Utility program.
Note: After you enter the Setup Utility program, select Save Changes and Exit at the bottom of the
screen. The error message will not be displayed again.
• Press F2 to bypass the error message and log in to the operating system.
Viewing and changing settings
The Setup Utility program menu lists various items about the system configuration. To view or change
settings, start the Setup Utility program. See “Starting the Setup Utility program” on page 37. Then, follow
the instructions on the screen.
You can use either the keyboard or the mouse to navigate through BIOS menu choices. The keys used to
perform various tasks are displayed at the bottom of each screen.
Using passwords
By using the Setup Utility program, you can set passwords to prevent unauthorized access to your computer
and data. The following types of passwords are available:
• Power-On Password
• Administrator Password
• Hard Disk Password
You do not have to set any passwords to use your computer. However, using passwords improves
computing security. If you decide to set any passwords, read the following sections.
© Copyright Lenovo 2012
37
Password considerations
A password can be any combination of up to 64 alphabetic and numeric characters. For security reasons, it
is recommended to use a strong password that cannot be easily compromised. To set a strong password,
use the following guidelines:
• Have at least eight characters in length
• Contain at least one alphabetic character and one numeric character
• Setup Utility program and hard disk drive passwords are not case sensitive
• Not be your name or your user name
• Not be a common word or a common name
• Be significantly different from your previous passwords
Power-On Password
When a Power-On Password is set, you are prompted to type a valid password each time the computer is
turned on. The computer cannot be used until the valid password is typed in.
Administrator Password
Setting an Administrator Password deters unauthorized users from changing configuration settings. If you
are responsible for maintaining the configuration settings of several computers, you might want to set an
Administrator Password.
When an Administrator Password is set, you are prompted to type a valid password each time you try to
access the Setup Utility program. The Setup Utility program cannot be accessed until a valid password
is typed in.
If both the Power-On Password and Administrator Password are set, you can type either password. However,
you must use your Administrator Password to change any configuration settings.
Hard Disk Password
Setting a Hard Disk Password prevents unauthorized access to the data on the hard disk drive. When a
Hard Disk Password is set, you are prompted to type a valid password each time you try to access the
hard disk drive.
Notes:
• After you set a Hard Disk Password, your data on the hard disk drive is protected even if the hard disk
drive is removed from one computer and installed in another.
• If the Hard Disk Password is forgotten, there is no way to reset the password or recover data from the
hard disk drive.
Setting, changing, and deleting a password
To set, change, or delete a password, do the following:
2. From the Setup Utility program main menu, select Security.
3. Depending on the password type, select Set Power-On Password, Set Administrator Password, or
Hard Disk Password.
4. Follow the instructions on the right side of the screen to set, change, or delete a password.
38 ThinkStation Hardware Maintenance Manual
Note: A password can be any combination of up to 64 alphabetic and numeric characters. For more
Erasing lost or forgotten passwords (clearing CMOS)
This section provides instructions on how to erase lost or forgotten passwords, such as a user password.
To erase a lost or forgotten password, do the following:
1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect
all power cords from electrical outlets and disconnect all cables that are connected to the computer.
4. Move the jumper from the standard position (pin 1 and pin 2) to the maintenance position (pin 2 and
pin 3).
5. Reinstall the computer cover and connect the power cord. See “Completing the parts replacement” on
page 104.
6. Turn on the computer and leave it on for approximately 10 seconds. Then, turn off the computer by
holding the power switch for approximately five seconds.
7. Repeat step 1 through step 2.
8. Move the Clear CMOS /Recovery jumper back to the standard position (pin 1 and pin 2).
9. Reinstall the computer cover and connect the power cord. See “Completing the parts replacement” on
page 104.
Enabling or disabling a device
This section provides information on how to enable or disable user access to the following devices:
USB Configuration
SATA Configuration
Use this option to enable or disable a USB connector. When a USB connector is
disabled, the device connected to the USB connector cannot be used.
Use this option to enable or disable a SATA connector or an external SATA connector.
To enable or disable a device, do the following:
2. Depending on the device you want to enable or disable, do one of the following:
• From the Setup Utility program main menu, select Devices ➙ South Bridge ➙ USB Configuration
to enable or disable a USB device.
• From the Setup Utility program main menu, select Advanced ➙ SATA Configuration to enable
or disable an internal or external SATA device.
3. Select the desired settings and press Enter.
4. Press F10 to save changes and exit the Setup Utility program. See “Exiting the Setup Utility program”
on page 41.
Selecting a startup device
If your computer does not start up from a device such as the disc or hard disk drive as expected, do one of
the following to select the startup device you want.
Chapter 6. Using the Setup Utility program 39
Selecting a temporary startup device
Use this procedure to select a temporary startup device.
Note: Not all discs and hard disk drives are bootable.
1. Turn off your computer.
2. Repeatedly press and release the F12 key when turning on the computer. When the Startup Device
Menu window displays, release the F12 key.
3. Select the desired startup device and press Enter. The computer will start up from the device you
selected.
Note: Selecting a startup device from the Please select boot device window does not permanently change
the startup sequence.
Selecting or changing the startup device sequence
To view or permanently change the configured startup device sequence, do the following:
2. From the Setup Utility program main menu, select Startup.
3. Select the devices for the Primary Startup Sequence, the Automatic Startup Sequence, the Error Startup
Sequence and Manufacturing Boot Sequence. Read the information displayed on the right side of
the screen.
4. Press F10 to save changes and exit the Setup Utility program. See “Exiting the Setup Utility program”
on page 41.
Enabling ErP compliance mode and Deep Sx
You can enable the ErP compliance mode and Deep Sx through the Devices menu in the Setup Utility
program to reduce the consumption of electricity when your computer is in standby or off mode.
To enable ErP compliance mode and Deep Sx in the Setup Utility program, do the following:
2. From the Setup Utility program main menu, select Devices ➙ South Bridge.
3. Select Deep Sx and press Enter.
4. Select Enabled in S4 and S5 and press Enter.
5. Press F10 to save changes and exit the Setup Utility program. Press Enter when prompted to confirm
the exit.
Note: When ErP compliance mode and Deep Sx are enabled, you can wake up your computer by doing one
of the following:
• Pressing the power switch
• Enabling the wake up on alarm feature
The wake up on alarm feature enables your computer to wake up at a set time. To enable the wake
up on alarm feature, do the following:
1. Start the Setup Utility program.
2. From the Setup Utility program main menu, select Power ➙ Automatic Power On, and press Enter.
3. Select Wake Up on Alarm and press Enter. Then follow the instructions on the screen.
4. Press F10 to save changes and exit the Setup Utility program. Press Enter when prompted to
confirm the exit.
• Enabling the after power loss feature
40 ThinkStation Hardware Maintenance Manual
The after power loss feature enables your computer to wake up when the power supply resumes after a
sudden loss of electricity. To enable the after power loss feature, do the following:
1. Start the Setup Utility program.
2. From the Setup Utility program main menu, select Power ➙ After Power Loss, and press Enter.
3. Select Power On and press Enter.
4. Press F10 to save changes and exit the Setup Utility program. Press Enter when prompted to
confirm the exit.
Exiting the Setup Utility program
After you finish viewing or changing settings, press Esc to return to the Setup Utility program main menu.
You might have to press Esc several times. Do one of the following:
• If you want to save the new settings, press F10 to save changes and exit the Setup Utility program.
• If you do not want to save the settings, select Exit ➙ Discard Changes and Exit, and then press Enter.
When the Reset Without Saving window shows, select Yes, and then press Enter to exit the Setup
Utility program.
• If you want to return to the default settings, press F9 to load the default settings, and then press F10 to
save and exit the Setup Utility program.
Chapter 6. Using the Setup Utility program 41
42 ThinkStation Hardware Maintenance Manual
Chapter 7. Configuring RAID
This chapter provides instructions on how to install hard disk drives and configure Redundant Array of
Independent Disks (RAID) for your computer. Depending on your computer model, RAID can be enabled by
Intel Rapid Storage Technology enterprise (RSTe) or the LSI MegaRAID BIOS.
Note: The RAID configuration information described in this chapter is only applicable in the Windows
environment. For information about configuring RAID in the Linux environment, contact your Linux software
provider.
This chapter provides information about the following topics:
•
•
Configuring RAID with Intel RSTe
If your computer comes with Intel RSTe, you can follow the sections below to configure RAID with Intel RSTe.
This section provides information about the following topics:
•
•
Installing SATA or SAS hard disk drives
Ensure that your computer has the minimum number of SATA or SAS hard disk drives installed for the
following supported levels of RAID:
• RAID Level 0 - Striped disk array
– A RAID Level 0 hard disk drive group consisting of at least two hard disk drives
– Supported strip size: 4 KB, 8 KB, 16 KB, 32 KB, 64 KB, or 128 KB
– Better performance without fault tolerance
• RAID Level 1 - Mirrored disk array
– A RAID Level 1 hard disk drive group consisting of two hard disk drives
– Improved reading performance and 100% redundancy
• RAID Level 10 - Striped and mirrored disk array (a combination of RAID Level 0 and RAID Level 1)
– A RAID Level 10 hard disk drive group consisting of four hard disk drives
– Supported strip size: 4 KB, 8 KB, 16 KB, 32 KB, or 64 KB
• RAID Level 5 - Block-level striped disk array with distributed parity
– A RAID Level 5 hard disk drive group consisting of at least three hard disk drives
– Supported strip size: 4 KB, 8 KB, 16 KB, 32 KB, or 64 KB
– Better performance and fault tolerance
Ensure that one of the following hard disk drive enablement modules is installed in your computer:
• If zero to four SATA hard disk drives or solid state drives are installed, no hard disk drive enablement
module is needed.
© Copyright Lenovo 2012
43
• If five SATA hard disk drives or solid state drives are installed, the SATA hard disk drive enablement
module (one to five hard disk drives) is required.
• If any SAS hard disk drives are installed, the SAS hard disk drive enablement module (one to five hard
disk drives) is required.
For more information about the hard disk drive enablement module, refer to “Installing or replacing a hard
Configuring SATA or SAS RAID functionality with the Intel RSTe
configuration utility
This section describes the information about configuring SATA or SAS RAID functionality with the Intel
RSTe configuration utility.
Note: The Intel RSTe configuration utility assumes that your computer is installed with more than one hard
disk drive. Therefore, if only one hard disk drive is installed in your computer, the following information
does not apply.
This section provides information about the following topics:
•
•
•
•
Entering the Intel RSTe configuration utility
This section provides instructions on how to enter the Intel RSTe configuration utility.
During the computer startup, follow the instructions on the screen. Press Ctrl+I to enter the Intel RSTe
configuration utility.
The following four options are displayed after you enter the Intel RSTe configuration utility:
1. Create RAID Volume
2. Delete RAID Volume
3. Reset Disks to Non ‐ RAID
4. Exit
Press the up and down arrow keys to select an option. Press Enter to enter the menu for the selected
option. Press Esc to exit the Intel RSTe configuration utility, or select Exit, and then press Enter to exit the
Intel RSTe configuration utility.
Creating RAID volumes using the Intel RSTe configuration utility
This section provides instructions on how to use the Intel RSTe configuration utility to create RAID volumes.
To create a RAID volume, do the following:
1. Enter the Intel RSTe configuration utility. See “Entering the Intel RSTe configuration utility” on page 44.
2. Press the up and down arrow keys to select Create RAID Volume, and then press Enter to view the
CREATE VOLUME MENU window.
3. The following five options are displayed. Press the up and down arrow keys to select an option. After
you configure an option, press Tab or Enter to go to the next option.
a. Name: Volume name. You can use the default name or type a preferred name.
b. RAID Level: You can change the RAID Level to one of the following:
44 ThinkStation Hardware Maintenance Manual
• RAID Level 0
• RAID Level 1
• RAID Level 10
• RAID Level 5
c. Disks: Press Enter to enter the SELECT DISKS MENU window. Follow the instructions at the bottom
of the menu to select hard disk drives, and then press Enter to complete the configuration.
d. Strip Size: Press the up and down arrow keys to select a strip size.
e. Capacity: Customize the capacity of the RAID volume. The default RAID volume is the largest value.
4. Press Enter to finish configuring all the five options. When prompted, press Y to confirm the creation of
the new RAID volume.
5. After the new RAID volume is created, the information about the RAID volume will be displayed under
DISK/VOLUME INFORMATION, such as ID number, name, RAID level, strip size, volume size, status,
and whether it is a bootable volume.
Deleting RAID volumes using the Intel RSTe configuration utility
This section provides instructions on how to use the Intel RSTe configuration utility to delete RAID volumes.
To delete a RAID volume, do the following:
1. Enter the Intel RSTe configuration utility. See “Entering the Intel RSTe configuration utility” on page 44.
2. Press the up and down arrow keys to select Delete RAID Volume. Press Enter to enter the DELETE
VOLUME MENU window.
3. Press the up and down arrow keys to select the RAID volume that is not needed. Press Del to delete it
from the RAID Volumes list.
4. When prompted, press Y to confirm the deletion of the selected RAID volume.
Resetting hard disk drives to non-RAID
This section provides instructions on how to reset hard disk drives to non-RAID.
To reset hard disk drives to non-RAID, do the following:
1. Enter the Intel RSTe configuration utility. See “Entering the Intel RSTe configuration utility” on page 44.
2. Press the up and down arrow keys to select Reset Disks to Non-RAID. Press Enter to enter the
RESET RAID DATA window.
3. Use the up and down arrow keys and the space key to mark individual hard disk drive to be reset,
and then press Enter to complete the selection.
4. When prompted, press Y to confirm the reset action.
5. If the hard disk drive you reset is part of a RAID volume, the computer might detect that the RAID volume
is degraded. In this case, you are prompted to select a hard disk drive to initiate a rebuild process.
6. Select an available hard disk drive, and then press Enter to initiate the rebuild process.
Note: Press Esc to cancel a rebuild process and keep the RAID volume in the degraded status. In the
Main Menu window under DISK/VOLUME INFORMATION, you will see the status of the RAID volume is
changed to Degraded.
Quick RAID setup using the LSI MegaRAID BIOS configuration utility
Notes:
• The LSI MegaRAID SAS adapter and the LSI MegaRAID BIOS configuration utility are only available
on some models.
• The following steps in this section are intended to guide you through a quick setup of basic
RAID functions with the LSI MegaRAID SAS adapter. For advanced setup and configuration
Chapter 7. Configuring RAID 45
using this adapter, refer to the complete MegaRAID SAS Software User Guide that is available at
http://support.lenovo.com/en_US/guides-and-manuals/detail.page?DocID=UM007543.
This section provides information about the following topics:
•
•
•
•
•
Installing SATA or SAS hard disk drives
Ensure that your computer has the minimum number of SATA or SAS hard disk drives installed for the
following supported levels of RAID:
• RAID Level 0 - Striped disk array
– A RAID Level 0 hard disk drive group consisting of at least one hard disk drive
– Supported strip size: 8 KB to 1 MB
– Better performance without fault tolerance
• RAID Level 00 - Spanned hard disk drive group with a series of RAID 0 hard disk drive groups
– A RAID Level 00 hard disk drive group consisting of two or four hard disk drives
– Supported strip size: 8 KB to 1 MB
– Better performance without fault tolerance
• RAID Level 1 - Mirrored disk array
– A RAID Level 1 hard disk drive group consisting of two or four hard disk drives
– Improved read performance and 100% redundancy
• RAID Level 10 - A combination of RAID Level 0 and RAID Level 1
– A RAID Level 10 hard disk drive group consisting of four hard disk drives
– Data being striped across hard disk drive groups
– Provides both high data transfer rates and complete data redundancy
• RAID Level 5 - Block-level striped disk array with distributed parity
– A RAID Level 5 hard disk drive group consisting of at least three hard disk drives
– Supported strip size: 8 KB to 1 MB
– Better performance and fault tolerance
– RAID Level 5 might not be available on all models of LSI MegaRAID adapter
• RAID Level 6 - Block-level striped disk array with dual distributed parity
– A RAID Level 6 hard disk drive group consisting of at least four hard disk drives
– Supported strip size: 8 KB to 1 MB
– Better performance and fault tolerance that can stand up to loss of two hard disk drives
– RAID Level 6 might not be available on all models of LSI MegaRAID adapter
Ensure that the LSI MegaRAID SAS adapter card is installed in your computer, and that the hard disk drives
are connected to this adapter card and not to the connectors on the system board.
46 ThinkStation Hardware Maintenance Manual
Entering the LSI MegaRAID BIOS configuration utility
This section provides instructions on how to enter the LSI MegeRAID BIOS configuration utility.
To enter the LSI MegaRAID BIOS configuration utility, do the following:
1. During the computer startup, follow the instructions on the screen.
2. Press Ctrl+H to enter the CONTROLLER SELECTION window.
3. Select the controller you want to configure, and then click Start to enter the LSI MegaRAID BIOS
configuration utility.
Creating RAID volumes using the LSI MegaRAID BIOS configuration
utility
This section provides instructions on how to create RAID volumes using the LSI MegaRAID BIOS
configuration utility.
To create RAID volumes using the LSI MegaRAID BIOS configuration utility, do the following:
1. Click Configuration Wizard on the WebBIOS main screen to enter the Choosing the Configuration
Type window.
2. Press the up and down arrow keys to select one of the three configuration types:
• Clear Configuration: Clear the existing configuration.
• New Configuration: Clear the existing configuration and create new configuration.
• Add Configuration: Retain the existing storage configuration and add new hard disk drives. The
new configuration will not cause any data loss.
3. Select Add Configuration, and then click Next. The following two options are displayed in the
Configuration Method window.
• Manual Configuration: Manually create hard disk drive groups and virtual hard disk drives, and
set parameters.
• Automatic Configuration: Automatically create an optimal RAID configuration.
4. Select Manual Configuration, and then click Next. The Drive Group Definition window is displayed. To
create hard disk drive groups, do the following:
a. Select one or more hard disk drives for the group (keep pressing Ctrl while selecting more than
one hard disk drive).
b. Click Add To Array to move the selected hard disk drives to Drive Groups.
c. Click Accept DG to create the hard disk drive group.
d. Repeat the above steps if you want to create more than one hard disk drive group.
5. Click Next. The Span Definition window is displayed. Select the hard disk drive group that you want
to add to a span, and then click Add to SPAN. Repeat this step until you have selected all the hard
disk drive groups you want.
6. Click Next. The Virtual Drive Definition window is displayed. Change the virtual hard disk drive options
from the default settings listed on the screen to the settings you want. Click Accept , and then follow
the instructions on the screen to customize your settings.
7. Click Next, and the Preview window is displayed.
8. Verify your settings, and then click Accept.
9. Click Yes to save the configuration.
Chapter 7. Configuring RAID 47
Deleting RAID volumes using the LSI MegaRAID BIOS configuration
utility
This section provides instructions on how to delete RAID volumes using the LSI MegaRAID BIOS
configuration utility.
To delete RAID volumes using the LSI MegaRAID BIOS configuration utility, do the following:
1. Enter the LSI MegaRAID BIOS configuration utility. See “Entering the LSI MegaRAID BIOS configuration
2. Click the virtual hard disk drives you want to delete, and then the Virtual Drive window is displayed.
3. Click Delete, and then click Go.
4. Click Yes to save your changes.
Setting the hot spare hard disk drive
This section provides instructions on how to set the hot spare hard disk drive.
To set the hot space hard disk drive, do the following:
1. Enter the LSI MegaRAID BIOS configuration utility. See “Entering the LSI MegaRAID BIOS configuration
2. Click the hard disk drive you want to set as the hot spare hard disk drive. The Drive window is displayed.
3. Select Make Global HSP or Make Dedicated HSP, and then click Go.
4. The main screen of the LSI MegaRAID BIOS configuration utility is displayed, and the hard disk drive
you selected is listed as a hot spare hard disk drive in the right pane.
48 ThinkStation Hardware Maintenance Manual
Chapter 8. Symptom-to-FRU Index
The Symptom-to-FRU index lists error symptoms and possible causes. The most likely cause is listed first.
decide which FRUs to have available when servicing a computer. If you are unable to correct the problem
Notes:
• If you have both an error message and an incorrect audio response, diagnose the error message first.
• If you cannot run the diagnostic tests or you get a diagnostic error message when running a test, but did receive a
POST error message, diagnose the POST error message first.
• If you did not receive any error message, look for a description of your error symptoms in the first part of this index.
Hard disk drive boot error
A hard disk drive boot error can have the following causes.
Error
FRU/Action
The start-up drive is not in the boot sequence in
configuration.
Check the configuration and ensure the start-up drive is
in the boot sequence.
No operating system installed on the boot drive.
The boot sector on the start-up drive is corrupted.
Install an operating system on the boot drive.
The drive must be formatted. Do the following:
1. Attempt to back up the data on the failing hard disk
drive.
2. Using the operating system programs, format the
hard disk drive.
The drive is defective.
Replace the hard disk drive.
Power Supply Problems
If you suspect a power problem, use the following procedures.
Check/Verify
FRU/Action
Reseat connectors
Check the following for proper installation.
• Power cord
• On/Off switch connector
• On/Off switch power supply connector
• System board power supply connectors
• Microprocessor(s) connection
Power cord
Check the power cord for continuity.
Check the turn on switch for continuity.
Turn on switch
Beep symptoms
Beep symptoms are tones or a series of tones separated by pauses (intervals without sound) during POST.
© Copyright Lenovo 2012
49
The following tables describes beep symptoms.
Beep Symptom
FRU/Action
2 short beeps CMOS setting error
Perform the following actions in order.
1. Start the Setup Utility program and press F10 to save
2. Start the Setup Utility program and press F9 to load
defaults and then press F10 to save and exit.
3. Perform a Boot block recovery. See “Recovering
1 long and 2 short beeps Monitor or video adapter card Perform the following actions in order.
error
1. Make sure the monitor is properly connected to the
computer.
2. Replace the video adapter card (if present).
3. Replace the system board.
1 long and 3 short beeps Keyboard error
Perform the following actions in order.
1. Make sure the keyboard is properly connected to the
keyboard connector.
2. Replace the keyboard.
3. Replace the system board.
1 long and 9 short beeps BIOS ROM error
Perform the following actions in order.
1. Start the Setup Utility program and press F9 to load
defaults and then press F10 to Save and exit. See
37.
2. Perform a Boot block recovery. See “Recovering
3. Replace the system board.
1-3-3-1 short beeps DRAM memory error
Perform the following actions in order.
1. Make sure the memory module(s) are properly seated
in the connector(s).
2. Replace the memory module(s).
3. Replace the system board.
POST error codes
Each time you Turn on the system, it performs a series of tests that check the operation of the system and
some options. This series of tests is called the Power-On Self-Test, or POST. POST does the following
operations.
• Checks some basic system-board operations
• Checks the memory operation
• Starts the video operation
• Verifies that the boot drive is working
If the POST detects a problem, an error message appears on the screen. A single problem can cause several
error messages to appear. When you correct the cause of the first error message, the other error messages
probably will not appear on the screen the next time you turn on the system.
50 ThinkStation Hardware Maintenance Manual
POST Error Message
Description/Action
CMOS battery failed
The CMOS battery is no longer functional.
Replace the battery.
CMOS checksum error - defaults loaded
Checksum of CMOS is incorrect.
The computer loads the default configuration settings.
This error might indicate that CMOS has become corrupt
due to a weak CMOS battery.
CPU at nnnn
nnnn is the running speed of the microprocessor.
Pressing Esc skips the full memory test
Press Esc to skip memory test
HARD DISK INSTALL FAILURE
Cannot find or initialize the hard disk drive controller or
the drive.
Make sure the hard disk drive is correctly installed.
If no hard disk drives are installed, make sure the hard
disk drive selection in Setup is set to NONE.
Keyboard error or no keyboard present
Cannot initialize the keyboard.
Make sure the keyboard is properly connected to the
computer and that no keys are held pressed during POST.
To purposely configure the computer without a keyboard,
set the error halt condition in Setup to HALT ON ALL, BUT
KEYBOARD. The BIOS then ignores the missing keyboard
during POST.
Memory Test:
This message displays during a full memory test, counting
down the memory areas being tested.
Memory test fail
If POST detects an error during memory testing, additional
information appears. This information gives specifics
about the type and location of the memory error.
Pressing the TAB key permits the user to toggle between
the default POST display screen and a custom POST
display screen.
Press TAB to show POST screen
Error: Non-System disk or disk error Replace and press
any key when ready
The BIOS was unable to find a suitable boot device.
Make sure the boot drive is properly connected to the
computer.
Make sure you have bootable media.
Miscellaneous error messages
Message/Symptom
FRU/Action
Changing display colors
Display/Monitor
1. Power switch
2. System board
3. Riser card, if installed.
Chapter 8. Symptom-to-FRU Index 51
Message/Symptom
FRU/Action
Computer will not RPL from server
1. Ensure that network is in startup sequence as first
device or first device after diskette.
2. Ensure that network adapter is enabled for RPL.
3. Network adapter (Advise network administrator of
new MAC address)
Computer will not perform a Wake On LAN® (if applicable)
1. Check power supply and signal cable connections
to network adapter.
2. Ensure that the operating system settings are set to
enable Wake on LAN.
3. Ensure Wake On LAN feature is enabled in
Setup/Configuration (see “Starting the Setup Utility
4. Ensure network administrator is using correct MAC
address.
5. Ensure no interrupt or I/O address conflicts.
6. Network adapter (advise network administrator of
new MAC address)
7. Replace system board
1. Power supply
Dead computer. See “Hard disk drive boot error” on page
49.
2. System board
Diskette drive in-use light remains on or does not light
when drive is active.
1. Diskette drive
2. System board
3. Diskette drive cable
Blank screen except for flashing cursor.
Incorrect memory size during POST
1. System board
2. Primary hard disk drive
3. Hard disk drive cable
1. Run the memory tests.
2. Memory module
3. System board
"Insert a Diskette" icon appears with a known-good
diagnostics diskette in the first 3.5-inch diskette drive.
1. System board
2. Diskette drive cable
3. Network adapter
1. Display
Intensity or color varies from left to right of characters
and color bars
2. Video adapter (if present)
3. System board
No power or fan not running
2. Replace system board
1. Diskette drive
Non-system disk or disk error-type message with a
known-good diagnostic diskette.
2. System board
3. Diskette drive cable
1. Display
Other display symptoms not listed above (including blank
or illegible display)
2. System board
Turn on indicator or hard disk drive in-use light not on, but
computer works correctly
1. Power switch/LED assembly
2. System board
52 ThinkStation Hardware Maintenance Manual
Message/Symptom
FRU/Action
1. Printer
Printer problems
2. System board
Program loads from the hard disk with a known-good
diagnostics diskette in the first 3.5-inch diskette drive
1. Run the Setup Utility program and check Startup
sequence.
2. Diskette drive
3. Diskette drive cable
4. System board
5. Power supply
RPL computer cannot access programs from its own hard
disk.
1. If network administrator is using LCCM Hybrid RPL,
check startup sequence:
a. First device - network
b. Second device - hard disk
2. Hard disk drive
RPL computer does not RPL from server
1. Check startup sequence.
2. Check the network adapter LED status.
Serial or parallel port device failure (system board port)
1. External device self-test OK?
2. External device
3. Cable
4. System board
Serial or parallel port device failure (adapter port)
1. External device self-test OK?
2. External device
3. Cable
4. Alternate adapter
5. System board
1. Keyboard
Some or all keys on the keyboard do not work
2. Keyboard cable
3. System board
Undetermined problems
This section provides instructions on how to find out the failing devices or adapters.
1. Turn off the computer.
2. Remove or disconnect the following components (if installed) one at a time.
a. External devices (modem, printer, or mouse)
b. Any adapters
c. Memory modules
d. Extended video memory
e. External Cache
f. External Cache RAM
g. Hard disk drive
h. Diskette drive
3. Turn on the computer to re-test the system.
4. Repeat steps 1 through 3 until you find the failing device or adapter.
Chapter 8. Symptom-to-FRU Index 53
If all devices and adapters have been removed, and the problem continues, replace the system board.
54 ThinkStation Hardware Maintenance Manual
Chapter 9. Locations
This chapter introduces the locations of the computer hardware components.
Locating connectors, controls, and indicators on the front of your
computer
connectors, controls, and indicators on the front of your computer.
Figure 1. Front connector, control, and indicator locations
1 Optical drive eject/close button
2 USB 2.0 connector
6 1394 connector (available on some models)
7 Power switch
3 Microphone connector
4 Headphone connector
5 USB 2.0 connector
8 Power indicator
9 Hard disk drive activity indicator
© Copyright Lenovo 2012
55
Locating connectors on the rear of your computer
Figure 2 “Rear connector locations” on page 56 shows the locations of the connectors on the rear of your
computer. Some connectors on the rear of your computer are color-coded to help you determine where to
connect the cables on your computer.
Figure 2. Rear connector locations
1 Power cord connector
7 Audio line-out connector
8 Microphone connector
9 USB 3.0 connectors (2)
10 USB 2.0 connectors (8)
11 Serial port
2 PS/2 keyboard and mouse connectors (optional)
3 Ethernet connectors (2)
4 Audio line-in connector
5 DisplayPort connector (number and location vary by
model)
6 DVI connector (number and location vary by model)
Locating major FRUs and CRUs
Figure 3 “Locating major FRUs and CRUs” on page 57 shows the locations of the major FRUs and CRUs in
56 ThinkStation Hardware Maintenance Manual
The following table lists the major FRUs shown in Figure 3 “Locating major FRUs and CRUs” on page 57 and
identifies which FRUs also are self-service CRUs or optional-service CRUs.
Notes:
• Self-service CRUs: These CRUs unplug or are secured by no more than two screws. Examples of
these types of CRUs include the keyboard, the mouse, any USB device, and the power cord. Other
self-service CRUs depending on product design might include memory modules, adapter cards, hard
disk drives, and optical drives.
• Optional-service CRUs: These CRUs are isolated parts within the computer and are concealed by an
access panel that is typically secured by more than two screws. Once the access panel is removed, the
specific CRU is visible.
Number
FRU description
Heat sink and fan assembly
Self-service CRU
Optional-service CRU
1
2
No
No
Yes
Yes
No
No
No
Yes
Yes
No
No
No
No
No
Internal speaker
3
Microprocessor
No
4
Yes
Yes
No
Optical drive (available in some models)
Card reader (available in some models)
Front audio and USB assembly
Front bezel
5
6
7
Yes
Yes
Yes
Yes
Yes
Yes
8
Hard disk drives
9
Hard disk drive fan assembly
Battery
10
11
12
Memory module
Peripheral Component Interconnect (PCI) card
retainer
13
14
15
16
17
18
Yes
No
No
Yes
No
No
No
No
PCI card
Rear fan assembly
System board
Power supply assembly
Keyboard
No
No
Yes
Yes
Mouse
Looking up FRU information
For detailed FRU information, such as the FRU part numbers and supported computer models, go to:
Locating parts on the system board
Figure 4 “System board part locations” on page 59 shows the locations of the parts on the system board.
58 ThinkStation Hardware Maintenance Manual
Figure 4. System board part locations
29 ATX power connector
30 12 volt power connector
31 SATA port 2
1 Microprocessor 2 memory slot 3 (DIMM3)
2 Microprocessor 2 memory slot 7 (DIMM7)
3 Microprocessor 2 memory slot 4 (DIMM4)
4 Microprocessor 2 memory slot 8 (DIMM8)
5 Microprocessor 2 memory cooler connector
6 Microprocessor 2 fan connector
32 SATA port 1
33 Hard disk drive connector 5
34 Hard disk drive connector 4
35 Hard disk drive connector 1
36 Hard disk drive connector 2
37 Hard disk drive connector 3
38 Battery
7 Microprocessor 1 memory slot 1 (DIMM1)
8 Microprocessor 1 memory slot 5 (DIMM5)
9 Microprocessor 1 memory slot 2 (DIMM2)
10 Microprocessor 1 memory slot 6 (DIMM6)
11 Microprocessor 1 12 volt power connector
12 Microprocessor 1
39 eSATA connector
40 Cover presence switch connector (Intrusion switch
connector)
13 Microprocessor 1 fan connector
41 Thermal sensor
42 Internal speaker connector
43 Front audio connector
44 PCI card slot
14 Microprocessor 1 memory slot 8 (DIMM8)
15 Microprocessor 1 memory slot 4 (DIMM4)
16 Microprocessor 1 memory slot 7 (DIMM7)
17 Microprocessor 1 memory slot 3 (DIMM3)
18 Front fan connector
45 PCI Express x4 card slot
46 PCI Express x16 card slot
47 PCI card slot
19 Microprocessor 1 memory cooler connector
Chapter 9. Locations 59
20 Clear CMOS (Complementary Metal Oxide
48 PCI Express x16 card slot
Semiconductor) / Recovery jumper
21 SATA port 4
49 PCI Express x4 card slot (x16 mechanical)
50 Rear fan connector
22 SATA port 3
23 Media card reader connector
24 Front panel connector
25 Front USB connector
26 Hard disk drive enablement module connector
27 Auxiliary LED connector
28 Internal USB 2.0 port
51 Microprocessor 2 memory slot 1 (DIMM1)
52 Microprocessor 2 memory slot 5 (DIMM5)
53 Microprocessor 2 memory slot 2 (DIMM2)
54 Microprocessor 2 memory slot 6 (DIMM6)
55 Microprocessor 2 12 volt power connector
56 Microprocessor 2
60 ThinkStation Hardware Maintenance Manual
Locating internal drives
Internal drives are devices that your computer uses to read and store data. You can add drives to your
computer to increase storage capacity and enable your computer to read other types of media. Internal
drives are installed in bays. In this manual, the bays are referred to as bay 1, bay 2, and so on.
When installing or replacing an internal drive, it is important to note the type and size of the drive that you
can install or replace in each bay and correctly connect the cables to the drive installed. Refer to the
appropriate section in “Installing or replacing hardware” on page 63 for instructions on how to install or
replace internal drives for your computer.
Figure 5. Drive bay locations
1 Optical drive bay 1 to 3 (with optical drives installed on some models)
2 Card reader drive bay
3 Hard disk drive bay 1 to 5 (with hard disk drives installed)
Chapter 9. Locations 61
62 ThinkStation Hardware Maintenance Manual
Chapter 10. Replacing FRUs
This chapter provides information about the FRU replacement instructions.
Important
Be sure to read and understand Chapter 2 “Safety information” on page 3 before replacing any FRU. These
precautions and guidelines will help you work safely.
Note: FRU replacements are to be done only by trained service technicians.
Installing or replacing hardware
This section provides instructions on how to install or replace hardware for your computer. You can expand
the capabilities of your computer and maintain your computer by installing or replacing hardware.
Attention: Do not open your computer or attempt any repair before reading and understanding the “Important
Notes:
1. Use only computer parts provided by Lenovo.
2. When installing or replacing an option, use the appropriate instructions in this section along with the
instructions that come with the option.
Handling static-sensitive devices
Do not open the static-protective package containing the new part until the defective part has been removed
from the computer and you are ready to install the new part. Static electricity, although harmless to you, can
seriously damage computer components and parts.
When you handle parts and other computer components, take these precautions to avoid static-electricity
damage:
• Limit your movement. Movement can cause static electricity to build up around you.
• Always handle parts and other computer components carefully. Handle PCI cards, memory modules,
system boards, and microprocessors by the edges. Never touch any exposed circuitry.
• Prevent others from touching the parts and other computer components.
• Before you replace a new part, touch the static-protective package containing the part to a metal
expansion-slot cover or other unpainted metal surface on the computer for at least two seconds. This
reduces static electricity in the package and your body.
• When possible, remove the new part from the static-protective packaging, and install it directly in the
computer without setting the part down. When this is not possible, place the static-protective package
that the part came in on a smooth, level surface and place the part on it.
• Do not place the part on the computer cover or other metal surface.
Installing external options
You can connect external options to your computer, such as external speakers, a printer, or a scanner. For
some external options, you must install additional software in addition to making the physical connection.
When installing an external option, see “Locating connectors, controls, and indicators on the front of your
computer” on page 55 and “Locating connectors on the rear of your computer” on page 56 to identify the
© Copyright Lenovo 2012
63
required connector. Then, use the instructions that come with the option to help you make the connection
and install any software or device drivers that are required for the option.
Removing the computer cover
Attention: Do not open your computer or attempt any repair before reading and understanding the “Important
This section provides instructions on how to remove the computer cover.
CAUTION:
Turn off the computer and wait three to five minutes to let the computer cool before removing the
computer cover.
To remove the computer cover, do the following:
1. Remove any media from the drives and turn off all attached devices and the computer.
2. Disconnect all power cords from electrical outlets.
3. Disconnect the power cords, Input/Output cables, and any other cables that are connected to the
computer. See “Locating connectors, controls, and indicators on the front of your computer” on page
55 and “Locating connectors on the rear of your computer” on page 56.
4. Remove any locking device that secures the computer cover, such as a padlock or an integrated
cable lock.
64 ThinkStation Hardware Maintenance Manual
5. Disengage the cover latch 1 and remove the cover. Place the cover on a flat surface.
Figure 6. Removing the computer cover
Removing and reinstalling the front bezel
Attention: Do not open your computer or attempt any repair before reading and understanding the “Important
This section provides instructions on how to remove and reinstall the front bezel.
To remove and reinstall the front bezel, do the following:
1. Turn off the computer and disconnect all power cords from electrical outlets.
Chapter 10. Replacing FRUs 65
3. Remove the front bezel by releasing the two plastic tabs on the left side and pivoting the front bezel
outward.
Figure 7. Removing the front bezel
4. To reinstall the front bezel, align the three plastic tabs on the right side of the front bezel with the
corresponding holes in the chassis, and then pivot the front bezel inwards until the two plastic tabs
snaps into position on the left side.
What to do next:
• To work with another piece of hardware, go to the appropriate section.
• To complete the installation or replacement, go to “Completing the parts replacement” on page 104.
Installing or replacing a PCI card
Attention: Do not open your computer or attempt any repair before reading and understanding the “Important
This section provides instructions on how to install or replace a PCI card. Your computer has two standard
PCI card slots, two PCI Express x4 card slots, and two PCI Express x16 graphics card slots.
To install or replace a PCI card, do the following:
1. Turn off the computer and disconnect all power cords from electrical outlets.
3. Open the PCI card retainer by lifting the retainer and then pivoting it out.
66 ThinkStation Hardware Maintenance Manual
Figure 8. Opening the PCI card retainer
4. Depending on whether you are installing or replacing a PCI card, do one of the following:
• If you are installing a PCI card, remove the appropriate metal card slot cover.
• If you are replacing an old PCI card, grasp the old card that is currently installed and gently pull it
out of the card slot.
Chapter 10. Replacing FRUs 67
Figure 9. Removing a PCI card
Notes:
a. The card fits tightly into the card slot. If necessary, alternate moving each side of the card a small
amount until it is removed from the card slot.
68 ThinkStation Hardware Maintenance Manual
b. If the card is held in place by a retaining latch, press the card retaining latch 1 as shown to
disengage the latch. Grasp the card and gently pull it out of the card slot.
5. Remove the new PCI card from its static-protective package.
6. Install the new card into the appropriate card slot on the system board. See “Locating parts on the
7. Pivot the PCI card latch to the closed position to secure the PCI card.
What to do next:
• To work with another piece of hardware, go to the appropriate section.
• To complete the installation or replacement, go to “Completing the parts replacement” on page 104.
Installing or replacing a memory module
Attention: Do not open your computer or attempt any repair before reading and understanding the “Important
This section provides instructions on how to install or replace a memory module.
CAUTION:
Chapter 10. Replacing FRUs 69
Turn off the computer and wait three to five minutes to let the computer cool before installing or
replacing a memory module.
Your computer has 16 slots for installing or replacing DDR3 ECC UDIMMs or DDR3 ECC RDIMMs. When
installing or replacing a memory module, use the following guidelines:
• Use either DDR3 ECC UDIMMs or DDR3 ECC RDIMMs for your computer. Do not install both the
UDIMMs and RDIMMs into the same computer.
• Use 2 GB, 4 GB, or 8 GB UDIMMs in any combination up to a maximum of 128 GB.
• Use 2 GB, 4 GB, 8 GB, 16 GB, or 32 GB DDR3 RDIMMs in any combination up to a maximum of 512 GB.
• Always install DIMMs in the numerical order printed on the system board (DIMM1, DIMM2, DIMM3,
and so on). Install memory modules into the blue color memory slots first. See “Locating parts on the
• If your computer has only one microprocessor installed, be sure to install memory modules only in the
memory slots adjacent to that microprocessor.
• If your computer has two microprocessors installed, install equal numbers of memory modules in both
sets of microprocessor DIMM slots for maximum performance.
To install or replace a memory module, do the following:
1. Turn off the computer and disconnect all power cords from electrical outlets.
3. Lay the computer on its side for easier access to the system board.
5. Remove any parts that might prevent your access to the memory slots. Depending on your computer
model, you might need to remove the PCI Express x16 graphics card for easier access to the memory
6. For some computer models, you might need to remove the memory fan duct to get access to the
memory slots. To remove the memory fan duct, disconnect the memory fan cable from the system
7. Pull the fan duct tab outward and pivot the fan duct, and then disengage the rear of the fan duct.
Note: Not all computer models have the memory fan duct.
Figure 10. Removing the memory fan duct
8. Depending on whether you are installing or replacing a memory module, do one of the following:
70 ThinkStation Hardware Maintenance Manual
• If you are replacing an old memory module, open the retaining clips and gently pull the memory
module out of the memory slot.
Figure 11. Removing a memory module
• If you are installing a memory module, open the retaining clips of the memory slot into which you
want to install the memory module.
Figure 12. Opening the retaining clips
Chapter 10. Replacing FRUs 71
9. Position the new memory module over the memory slot. Make sure that the notch 1 on the memory
module aligns correctly with the slot key 2 on the system board. Push the memory module straight
down into the slot until the retaining clips close.
Figure 13. Installing a memory module
10. To install the memory fan duct, secure the rear of the fan duct with the retaining clips of the memory
slots, and then pivot the fan duct downward until the fan duct snaps into position.
Figure 14. Installing the memory fan duct
on page 58.
12. Reinstall the PCI Express x16 graphics card if you have removed it.
What to do next:
• To work with another piece of hardware, go to the appropriate section.
• To complete the installation or replacement, go to “Completing the parts replacement” on page 104.
Installing or replacing the optical drive
Attention: Do not open your computer or attempt any repair before reading and understanding the “Important
72 ThinkStation Hardware Maintenance Manual
This section provides instructions on how to install or replace the optical drive.
To install or replace an optical drive, do the following:
1. Turn off the computer and disconnect all power cords from electrical outlets.
4. Locate the optical drive. See “Locating major FRUs and CRUs” on page 56.
5. Depending on whether you are installing or replacing an optical drive, do one of the following:
• If you are installing a secondary optical drive, remove the plastic panel in the front bezel for the
drive bay you want to use. If there is a metal static shield installed in the drive bay, remove the
metal static shield.
• If you are replacing an optical drive, disconnect the signal cable and the power cable from the rear
of the optical drive, press the drive latch 1 , and then slide the optical drive out of the front of the
computer.
Figure 15. Removing the optical drive
Chapter 10. Replacing FRUs 73
6. Install the optical drive retainer on the side of the new optical drive.
Figure 16. Installing the optical drive retainer
7. Slide the new optical drive into the drive bay from the front of the computer until the optical drive
snaps into position.
Figure 17. Installing the optical drive
74 ThinkStation Hardware Maintenance Manual
8. Connect the signal cable and the power cable to the new optical drive.
Figure 18. Connecting the optical drive
What to do next:
• To work with another piece of hardware, go to the appropriate section.
• To complete the installation or replacement, go to “Completing the parts replacement” on page 104.
Replacing the card reader
Attention: Do not open your computer or attempt any repair before reading and understanding the “Important
This section provides instructions on how to install or replace the card reader.
To replace the card reader, do the following:
1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect
all power cords from electrical outlets and disconnect all cables that are connected to the computer.
4. Locate the card reader. See “Locating major FRUs and CRUs” on page 56.
on page 58.
Chapter 10. Replacing FRUs 75
6. Press the blue retaining clip 1 to remove the card reader out of the chassis.
Figure 19. Removing the card reader
7. Install the card reader retainer on the side of the new card reader.
Figure 20. Installing the card reader retainer
76 ThinkStation Hardware Maintenance Manual
8. Slide the card reader with retainer into the card reader drive bay until it snaps into position.
Figure 21. Installing the card reader
on page 58.
What to do next:
• To work with another piece of hardware, go to the appropriate section.
• To complete the installation or replacement, go to “Completing the parts replacement” on page 104.
Replacing the battery
Attention: Do not open your computer or attempt any repair before reading and understanding the “Important
Your computer has a special type of memory that maintains the date, time, and settings for built-in features,
such as parallel-port assignments (configuration). A battery keeps this information active when you turn
off the computer.
The battery normally requires no charging or maintenance throughout its life; however, no battery lasts
forever. If the battery fails, the date, time, and configuration information (including passwords) are lost. An
error message is displayed when you turn on the computer.
Chapter 10. Replacing FRUs 77
Refer to the “Lithium battery notice” in the ThinkStation Safety and Warranty Guide for information about
replacing and disposing of the battery.
To replace the battery, do the following:
1. Turn off the computer and disconnect all power cords from electrical outlets.
4. Remove the old battery.
Figure 22. Removing the old battery
5. Install a new battery.
Figure 23. Installing a new battery
page 104.
Note: When the computer is turned on for the first time after replacing the battery, an error message
might be displayed. This is normal after replacing the battery.
7. Turn on the computer and all attached devices.
8. Use the Setup Utility program to set the date, time, and any passwords. See Chapter 6 “Using the Setup
What to do next:
• To work with another piece of hardware, go to the appropriate section.
• To complete the installation or replacement, go to “Completing the parts replacement” on page 104.
Replacing the heat sink and fan assembly
Attention: Do not open your computer or attempt any repair before reading and understanding the “Important
This section provides instructions on how to replace the heat sink and fan assembly.
78 ThinkStation Hardware Maintenance Manual
CAUTION:
The heat sink and fan assembly might be very hot. Turn off the computer and wait three to five
minutes to let the computer cool before removing the computer cover.
To replace the heat sink and fan assembly, do the following:
1. Turn off the computer and disconnect all power cords from electrical outlets.
3. Lay the computer on its side for easier access to the system board.
4. Locate the heat sink and fan assembly you want to replace. Your computer have two heat sink and fan
5. Disconnect the heat sink and fan assembly cable from the microprocessor fan connector on the system
6. Follow this sequence to remove the four screws that secure each heat sink and fan assembly to the
system board:
a. Partially remove screw 1 , then fully remove screw 2 , and then fully remove screw 1 .
b. Partially remove screw 3 , then fully remove screw 4 , and then fully remove screw 3 .
Note: Carefully remove the four screws from the system board to avoid any possible damage to the
system board. The four screws cannot be removed from the heat sink and fan assembly.
Figure 24. Removing the heat sink and fan assembly
7. Lift the failing heat sink and fan assembly off the system board.
Notes:
a. You might have to gently twist the heat sink and fan assembly to free it from the microprocessor.
b. Do not touch the thermal grease while handling the heat sink and fan assembly.
8. Position the two new heat sink and fan assemblies in a way that the fans are toward the rear of the
computer. Align the four screws on each heat sink and fan assembly with the holes on the system board.
Chapter 10. Replacing FRUs 79
9. Follow the following sequence to install the four screws to secure each new heat sink and fan assembly.
Do not over-tighten the screws.
a. Partially tighten screw 1 , then fully tighten screw 2 , and then fully tighten screw 1 .
b. Partially tighten screw 3 , then fully tighten screw 4 , and then fully tighten screw 3 .
10. Connect the heat sink and fan assembly cables to the microprocessor fan connectors on the system
What to do next:
• To work with another piece of hardware, go to the appropriate section.
• To complete the installation or replacement, go to “Completing the parts replacement” on page 104.
Replacing the hard disk drive fan assembly
Attention: Do not open your computer or attempt any repair before reading and understanding the “Important
This section provides instructions on how to replace the hard disk drive fan assembly.
To replace the hard disk drive fan assembly, do the following:
1. Turn off the computer and disconnect all power cords from electrical outlets.
3. Disconnect the hard disk drive fan assembly cable from the system board. See “Locating parts on the
4. Remove any parts that might prevent your access to the hard disk drive fan assembly. Depending on
your computer model, you might need to remove the PCI Express x16 graphics card for easier access to
80 ThinkStation Hardware Maintenance Manual
5. Press the tab, and then pivot the hard disk drive fan outward to remove it from the chassis.
Figure 25. Removing the hard disk drive fan assembly
6. Position the hard disk drive fan, and then pivot the fan to insert the tab into the chassis.
7. Reconnect the hard disk drive fan cable to the system board.
What to do next:
• To work with another piece of hardware, go to the appropriate section.
• To complete the installation or replacement, go to “Completing the parts replacement” on page 104.
Replacing the rear fan assembly
Attention: Do not open your computer or attempt any repair before reading and understanding the “Important
This section provides instructions on how to replace the rear fan assembly.
To replace the rear fan assembly, do the following:
1. Turn off the computer and disconnect all power cords from electrical outlets.
3. Locate the rear fan assembly. See “Locating major FRUs and CRUs” on page 56.
4. Disconnect the rear fan assembly cable from the system fan connector on the system board. See
Chapter 10. Replacing FRUs 81
5. The rear fan assembly is attached to the chassis by four rubber mounts. Remove the rear fan assembly
by breaking or cutting the rubber mounts and gently pulling the rear fan assembly out of the chassis.
Note: The new rear fan assembly will have four new rubber mounts attached.
Figure 26. Removing the rear fan assembly
6. Install the new rear fan assembly by aligning the new rubber mounts with the corresponding holes in
the chassis and push the rubber mounts through the holes. Pull on the tips of the rubber mounts
until the rear fan assembly is secured in place.
82 ThinkStation Hardware Maintenance Manual
Figure 27. Installing the rear fan assembly
7. Connect the rear fan assembly cable to the system fan connector on the system board.
What to do next:
• To work with another piece of hardware, go to the appropriate section.
• To complete the installation or replacement, go to “Completing the parts replacement” on page 104.
Installing or replacing a hard disk drive
Attention: Do not open your computer or attempt any repair before reading and understanding the “Important
This section provides instructions on how to install or replace a hard disk drive.
Notes: If you are installing additional hard disk drives, ensure that your computer is properly configured
to support them.
• If installing five SATA hard disk drives, ensure that the SATA hard disk drive enablement module (one to
five hard disk drives) is installed.
• If installing SAS hard disk drives, ensure that the SAS hard disk drive enablement module or the LSI
MegaRAID SAS adapter is installed.
To install or replace a hard disk drive, do the following:
1. Turn off the computer and disconnect all power cords from electrical outlets.
Chapter 10. Replacing FRUs 83
4. Disconnect the signal cable and the power cable from the hard disk drive.
5. Pull the bracket handle out to remove the hard disk drive from the chassis.
Figure 28. Removing the hard disk drive
6. Flex the sides of the bracket to remove the hard disk drive from the bracket.
84 ThinkStation Hardware Maintenance Manual
7. To install a new hard disk drive into the bracket, flex the bracket and align pin 1 , pin 2 , pin 3 , and
pin 4 on the bracket with the corresponding holes in the hard disk drive. Do not touch the circuit
board 5 on the bottom of the hard disk drive.
Figure 29. Installing the hard disk drive into the bracket
Note: If you are replacing or installing a 2.5-inch hard disk drive, you need to install it into a 2.5 to
3.5-inch converter bracket. Then install the 2.5-inch hard disk drive with the converter bracket into
the 3.5-inch hard disk drive bracket.
Figure 30. Installing 2.5-inch to 3.5-inch converter bracket before installing the outer bracket
8. Slide the new hard disk drive into the drive cage until it snaps into position.
Chapter 10. Replacing FRUs 85
Figure 31. Installing the hard disk drive
9. Connect the signal cable and the power cable to the new hard disk drive.
Note: If you are installing SAS hard disk drives, you must connect the signal cables and power cables to
the SAS-to-SATA conversion adapter before you connect them to the hard disk drive.
Figure 32. Connecting SAS cables to SAS-to-SATA conversion adapter
86 ThinkStation Hardware Maintenance Manual
What to do next:
• To work with another piece of hardware, go to the appropriate section.
• To complete the installation or replacement, go to “Completing the parts replacement” on page 104.
Installing or replacing a hard disk drive enablement module
Attention: Do not open your computer or attempt any repair before reading and understanding the “Important
This section provides instructions on how to install or replace a hard disk drive enablement module.
To install or replace a hard disk drive enablement module, do the following:
1. Turn off the computer and disconnect all power cords from electrical outlets.
4. Remove the hard disk drive fan assembly. See “Replacing the hard disk drive fan assembly” on page 80.
5. Locate the hard disk drive enablement module. See “Locating parts on the system board” on page 58.
6. If you are replacing the hard disk drive enablement module, press the plastic tabs together and then lift
the hard disk drive enablement module upward to remove it from the system board.
Figure 33. Removing the hard disk drive enablement module
Chapter 10. Replacing FRUs 87
7. To install a new hard disk drive enablement module, align the hole in the hard disk drive enablement
module with the plastic standoff on the system board, and then position the hard disk drive module over
the corresponding connector on the system board.
Figure 34. Installing a new hard disk drive enablement module
8. Reinstall the hard disk drive fan assembly and close the PCI card retainer. See “Replacing the hard
What to do next:
• To work with another piece of hardware, go to the appropriate section.
• To complete the installation or replacement, go to “Completing the parts replacement” on page 104.
Replacing the front audio and USB assembly
Attention: Do not open your computer or attempt any repair before reading and understanding the “Important
This section provides instructions on how to replace the front audio and USB assembly.
To replace the front audio and USB assembly, do the following:
1. Turn off the computer and disconnect all power cords from electrical outlets.
4. Locate the front audio and USB assembly. See “Locating major FRUs and CRUs” on page 56.
88 ThinkStation Hardware Maintenance Manual
Note: Make sure you note the locations of the cables when you disconnect the cables from the system
board.
6. Remove the two screws that secure the front audio and USB assembly bracket, and then remove
the bracket from the chassis.
Figure 35. Removing the two screws that secure the front audio and USB assembly to the chassis
7. Position the front audio and USB assembly bracket into the chassis, and then align the two screw holes
in the bracket with the corresponding holes in the chassis. Install the two screws to secure the front
audio and USB bracket to the chassis.
8. Reconnect the front audio and USB assembly cables to the front audio connector and the front USB
What to do next:
• To work with another piece of hardware, go to the appropriate section.
• To complete the installation or replacement, go to “Completing the parts replacement” on page 104.
Replacing the internal speaker
Attention: Do not open your computer or attempt any repair before reading and understanding the “Important
This section provides instructions on how to replace the internal speaker.
Chapter 10. Replacing FRUs 89
Note: The internal speaker is only available on some models.
To replace the internal speaker, do the following:
1. Turn off the computer and disconnect all power cords from electrical outlets.
3. Locate the internal speaker connector and disconnect the internal speaker cable form the system board.
4. Press the tab 3 inward and slide the internal speaker 1 upward to completely remove it from the chassis.
Figure 36. Removing the internal speaker
5. Position the new internal speaker to insert the two tabs 2 into the corresponding holes in the chassis,
and then push downward the internal speaker until it is secured in place.
on page 58.
What to do next:
• To work with another piece of hardware, go to the appropriate section.
• To complete the installation or replacement, go to “Completing the parts replacement” on page 104.
Installing or replacing the microprocessor
This topic provides instructions on how to install or replace the microprocessor.
90 ThinkStation Hardware Maintenance Manual
Installing the second microprocessor
Attention: Do not open your computer or attempt any repair before reading and understanding the “Important
This topic provides instructions on how to install the second microprocessor.
Depending on the model, your computer might come with one or two microprocessors. For computer
models with one microprocessor, the microprocessor is installed in the microprocessor socket 1 and the
microprocessor socket 2 is protected by a plastic socket cover. You can purchase a microprocessor option
kit from Lenovo and install the second microprocessor to expand system capabilities.
CAUTION:
The heat sink and microprocessor might be very hot. Turn off the computer and wait
three to five minutes to let the computer cool before removing the computer cover.
Notes:
• Ensure that you install the correct type of microprocessor option your computer supports. When two
microprocessors are installed, both must be identical.
• A second heat sink and fan assembly is also required. Ensure that you have this assembly available
before starting the installation.
• Use any documentation that comes with the microprocessor option kit and follow those instructions in
addition to the instructions in this topic.
• Your microprocessor, socket, and socket cover might look slightly different from the illustrations in this
topic.
To install the second microprocessor, do the following:
1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect
all power cords from electrical outlets and disconnect all cables that are connected to the computer.
3. Place the computer on its side to gain easier access to the system board.
on page 58.
Chapter 10. Replacing FRUs 91
5. Open the small handle 2 by gently pressing down the small handle, and then pulling the small handle
a little bit outward to release it from the secured position. Then, open the other small handle 1 by
following the same instructions. Ensure that the small handles are in the fully open position.
Note: There are two marks on the microprocessor retainer. You need to open the small handle marked
with
first, and then you can open the other small handle marked with
.
Figure 37. Opening the handles
6. Gently press down the small handle 2 to open the microprocessor retainer. Pivot the retainer upward
until it is in the fully open position.
Figure 38. Opening the microprocessor retainer
7. Touch only the edges of the microprocessor and carefully lift it straight up and out of the microprocessor
socket. Place the old microprocessor on a static-protective surface.
Notes:
• Do not touch the gold contacts on the bottom of the microprocessor.
92 ThinkStation Hardware Maintenance Manual
• Do not drop anything onto the microprocessor socket while it is exposed. The socket pins must be
kept as clean as possible.
Figure 39. Removing the microprocessor
8. Touch the static-protective package that contains the new microprocessor to any unpainted surface on
the outside of the computer. Then, remove the new microprocessor from the package.
9. Remove the new microprocessor from the protective cover that protects the gold contacts on the
bottom of the new microprocessor. Do not touch the pins on the microprocessor socket or the gold
contacts on the bottom of the new microprocessor.
Figure 40. Do not touch the pins
Chapter 10. Replacing FRUs 93
10. Note the orientation of the new microprocessor. Hold the new microprocessor by its edges and align
the notches 1 on it with the tabs 2 in the microprocessor socket. Then, carefully lower the new
microprocessor straight down into the microprocessor socket.
Note: The small triangle 3 on one corner of the new microprocessor is the microprocessor orientation
indicator. The new microprocessor is in the correct orientation when this indicator faces the beveled
corner 4 of the microprocessor socket.
Figure 41. Installing the microprocessor
11. Pivot the microprocessor retainer downward to close the retainer.
Figure 42. Closing the microprocessor retainer
94 ThinkStation Hardware Maintenance Manual
12. Gently press down the small handle 1 , and then push the handle inward to secure it. Then gently press
down the small handle 2 and push the handle inward to lock the microprocessor retainer into position
and secure the new microprocessor in the socket.
Note: There are two marks on the microprocessor retainer. Ensure that you close the small handle
marked with
first, and then close the small handle marked with
. Always follow the
correct sequence when you close the small handles.
Figure 43. Securing the microprocessor in the socket
13. Install the heat sink and fan assembly. See “Replacing the heat sink and fan assembly” on page 78.
What to do next:
• To work with another piece of hardware, go to the appropriate section.
Replacing a microprocessor
Attention: Do not open your computer or attempt any repair before reading and understanding the “Important
This section provides instructions on how to replace a microprocessor.
Depending on the model, your computer might come with one or two microprocessors. For computer
models with one microprocessor, the microprocessor is installed in the microprocessor socket 1 and the
microprocessor socket 2 is protected by a plastic socket cover. You can purchase a microprocessor option
kit from Lenovo and install the second microprocessor to expand computer capabilities.
CAUTION:
The heat sink and microprocessor might be very hot. Turn off the computer and wait
three to five minutes to let the computer cool before removing the computer cover.
Notes:
• Ensure that you install the correct type of microprocessor option your computer supports. When two
microprocessors are installed, both must be identical.
Chapter 10. Replacing FRUs 95
• Use any documentation that comes with the microprocessor option kit and follow those instructions in
addition to the instructions in this topic.
• Your microprocessor, socket, and socket cover might look slightly different from the illustrations in this
topic.
To replace a microprocessor, do the following:
1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect
all power cords from electrical outlets and disconnect all cables that are connected to the computer.
3. Place the computer on its side to gain easier access to the system board.
4. Remove the heat sink and fan assembly. See “Replacing the heat sink and fan assembly” on page 78.
on page 99.
6. Open the small handle 2 by gently pressing down the small handle, and then pulling the small handle
a little bit outward to release it from the secured position. Then, open the other small handle 1 by
following the same instructions. Ensure that the small handles are in the fully open position.
Figure 44. Opening the handles
7. Gently press down the small handle 2 to open the microprocessor retainer. Pivot the retainer upward
until it is in the fully open position.
96 ThinkStation Hardware Maintenance Manual
Figure 45. Opening the microprocessor retainer
8. Touch only the edges of the microprocessor and carefully lift it straight up and out of the microprocessor
socket. Place the old microprocessor on a static-protective surface.
Notes:
• Do not touch the gold contacts on the bottom of the microprocessor.
• Do not drop anything onto the microprocessor socket while it is exposed. The socket pins must be
kept as clean as possible.
Figure 46. Removing the microprocessor
9. Touch the static-protective package that contains the new microprocessor to any unpainted surface on
the outside of the computer. Then, remove the new microprocessor from the package.
Chapter 10. Replacing FRUs 97
10. Remove the new microprocessor from the protective cover that protects the gold contacts on the
bottom of the new microprocessor. Do not touch the pins on the microprocessor socket or the gold
contacts on the bottom of the new microprocessor.
Figure 47. Do not touch the pins
11. Note the orientation of the new microprocessor. Hold the new microprocessor by its edges and align
the notches 1 on it with the tabs 2 in the microprocessor socket. Then, carefully lower the new
microprocessor straight down into the microprocessor socket.
Note: The small triangle 3 on one corner of the new microprocessor is the microprocessor orientation
indicator. The new microprocessor is in the correct orientation when this indicator faces the beveled
corner 4 of the microprocessor socket.
Figure 48. Installing the microprocessor
98 ThinkStation Hardware Maintenance Manual
12. Pivot the microprocessor retainer downward to close the retainer.
Figure 49. Closing the microprocessor retainer
13. Gently press down the small handle 1 , and then push the handle inward to secure it. Then gently press
down the small handle 2 and push the handle inward to lock the microprocessor retainer into position
and secure the new microprocessor in the socket.
Note: There are two marks on the microprocessor retainer. Ensure that you close the small handle
marked with
first, and then close the small handle marked with
. Always follow the
correct sequence when you close the small handles.
Figure 50. Securing the microprocessor in the socket
14. Reinstall the heat sink and fan assembly. See “Replacing the heat sink and fan assembly” on page 78.
15. If you are instructed to return the old microprocessor, follow all packaging instructions and use any
packaging materials that are supplied to you for shipping.
Replacing the system board
Attention: Do not open your computer or attempt any repair before reading and understanding the “Important
This section provides instructions on how to replace the system board.
Chapter 10. Replacing FRUs 99
CAUTION:
The heat sink and microprocessor might be very hot. Turn off the computer and wait
three to five minutes to let the computer cool before removing the computer cover.
Note: Before replacing the system board, make sure you have a retention module for the new system board.
To replace the system board, do the following:
1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect
all power cords from electrical outlets and disconnect all cables that are connected to the computer.
3. Place the computer on its side to gain easier access to the system board.
4. Remove all memory modules and PCI cards that are currently installed. See “Installing or replacing a
5. Remove the hard disk drive fan assembly. See “Replacing the hard disk drive fan assembly” on page 80.
6. Remove the hard disk drive enablement module if it is installed. See “Installing or replacing a hard disk
7. Remove the heat sink and fan assembly from the failing system board. See “Replacing the heat sink and
page 95.
10. Note the location of all cable connections on the system board and disconnect all cables. See “Locating
11. Remove the ten screws that secure the system board to the chassis by following the sequence from 1
to 10 .
Figure 51. Removing the ten screws that secure the system board to the chassis
100 ThinkStation Hardware Maintenance Manual
12. Carefully lift the failing system board out of the chassis.
13. Position the new system board into the chassis so that the screw holes in the new system board are
aligned with those in the chassis. Install the ten screws that secure the system board to the chassis by
following the sequence from 10 to 1 .
14. Remove the microprocessor socket cover(s) from the new system board.
15. Install the memory modules, PCI cards, battery, microprocessor, heat sink and fan assembly, hard disk
drive enablement module (if applicable), and the hard disk drive fan assembly that you removed from the
failing system board to the new system board.
The failing system board must be returned with microprocessor socket covers to protect the pins during
shipping and handling. Install the microprocessor socket covers removed from the new system board
on the failing system board.
Note: The microprocessor socket cover installation procedure should be performed on both microprocessor
sockets on the failing system board.
To install the microprocessor socket cover on the failing system board:
1. Pivot the microprocessor retainer downward to close the retainer.
Figure 52. Closing the microprocessor retainer
2. Gently press down the small handle 1 , and then push the handle inward to secure it. Then gently press
down the small handle 2 and push the handle inward to lock the microprocessor retainer into position.
Chapter 10. Replacing FRUs 101
Figure 53. Securing the microprocessor in the socket
3. Align the notch 1 of the microprocessor socket cover with the alignment key 2 of the microprocessor
socket. Lower the socket cover straight down into the microprocessor socket on the system board.
Figure 54. Installing the microprocessor socket cover
Note: Your microprocessor socket and cover might look slightly different from the illustration.
Replacing the power supply assembly
Attention: Do not open your computer or attempt any repair before reading and understanding the “Important
This document provides instructions on how to replace the power supply assembly.
CAUTION:
Never remove the cover on a power supply or any part that has the following label attached.
102 ThinkStation Hardware Maintenance Manual
Hazardous voltage, current, and energy levels are present inside any component that has this label
attached. There are no serviceable parts inside these components.
CAUTION:
The heat sink and microprocessor might be very hot. Turn off the computer and wait
three to five minutes to let the computer cool before removing the computer cover.
To replace the power supply assembly, do the following:
1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect
all power cords from electrical outlets and disconnect all cables that are connected to the computer.
2. Remove any locking device that secures the computer cover, such as a padlock or an integrated
cable lock.
4. Place the computer on its side to gain easier access to the power supply.
5. Disconnect the power supply assembly cables from the system board and the drives. In some models,
you might need to disconnect the power supply assembly cables from the Peripheral Component
Interconnect (PCI) cards.
6. Remove the six screws that secure the power supply as shown in the following illustration.
Figure 55. Removing six screws that secure the power supply assembly
7. Slide the power supply assembly toward the front of the computer and then lift it out of the chassis.
8. Install the new power supply assembly into the chassis, and make sure the screw holes in the new
power supply assembly align with those in the chassis.
9. Install the six screws that secure the new power supply assembly in place.
10. Connect the power supply assembly cables to the system board and all drives. In some models, you
might need to connect the power supply assembly cables to the PCI cards.
11. Return the computer to its original position.
Chapter 10. Replacing FRUs 103
12. To complete the installation or replacement, go to “Completing the parts replacement” on page 104.
Completing the parts replacement
After completing the installation or replacement for all parts, you need to reinstall the computer cover and
reconnect cables. Depending on the parts you installed or replaced, you might need to confirm the updated
information in the Setup Utility program. Refer to Chapter 6 “Using the Setup Utility program” on page 37.
To reinstall the computer cover and reconnect cables to your computer, do the following:
1. Ensure that all components have been reassembled correctly and that no tools or loose screws are left
inside your computer. See “Locating major FRUs and CRUs” on page 56 for the locations of various
components in your computer.
2. If you have removed the front bezel, reinstall it.
3. Ensure that the cables are routed correctly before reinstalling the computer cover. Keep cables clear of
the hinges and sides of the computer chassis to avoid interference with reinstalling the computer cover.
4. Align the cover with the chassis, and then close the cover to engage the cover latch. Use the keys
attached at the rear of your computer to lock the keylock that is built into the computer cover.
5. If there is a padlock available, lock the computer cover.
6. If there is an integrated cable lock available, lock the computer..
7. Reconnect the external cables and power cords to the computer. See “Locating connectors on the
rear of your computer” on page 56.
Note: In most areas of the world, Lenovo requires the return of the defective Customer Replaceable Unit
(CRU). Information about this will come with the CRU or will come a few days after the CRU arrives.
Obtaining device drivers
You can obtain device drivers for operating systems that are not preinstalled at
http://www.lenovo.com/support. Installation instructions are provided in readme files with the device-driver
files.
104 ThinkStation Hardware Maintenance Manual
Chapter 11. Additional service information
This chapter provides additional information that the service representative might find helpful.
Security features
Security features in this section include the following:
• Passwords
• Vital Product Data
• Management Information Format (MIF)
Hardware-controlled passwords
Hardware-controlled passwords are set using the Setup Utility program. For more information about
Operating system password
An operating system password is very similar to a power-on password and denies access to the computer
by an unauthorized user when the password is activated. The computer is unusable until the password is
entered and recognized by the computer.
Vital product data
Each computer has a unique Vital Product Data (VPD) code stored in the nonvolatile memory on the system
board. After you replace the system board, the VPD must be updated. To update the VPD, see “Updating
BIOS levels
An incorrect level of BIOS can cause false errors and unnecessary FRU replacement. Use the following
information to determine the current level of BIOS installed in the computer, the latest BIOS available for the
computer, and where to obtain the latest level of BIOS.
• To determine the current Level of BIOS:
– Start the Setup Utility program.
• Sources for obtaining the latest level BIOS available
1. Lenovo support web site: http://www.lenovo.com/support
2. Lenovo Customer Support Center
3. Levels 1 and 2 Support
Updating (flashing) the BIOS
This section provides instructions on how to update the BIOS for your computer.
Updating (flashing) the BIOS from a disc
This section provides instructions on how to update (flash) the BIOS from a disc.
© Copyright Lenovo 2012
105
Note: You can download a self-starting bootable disc image (known as an ISO image) with the system
program updates to create a system-program-update disc. Go to:
To update (flash) the BIOS from a disc, do the following:
1. Turn off your computer.
2. Repeatedly press and release the F12 key when turning on the computer. When the Startup Device
Menu window opens, release the F12 key.
3. From the Startup Device Menu window, select the desired optical drive as the startup device. Then,
insert the disc into this optical drive and press Enter. The update begins.
4. When prompted to change the serial number, it is suggested that you do not make this change by
pressing N. However, if you do want to change the serial number, press Y, then type in the serial number
and press Enter.
5. When prompted to change the machine type and model, it is suggested that you do not make this
change by pressing N. However, if you do want to change the machine type and model, press Y, then
type in the machine type and model and press Enter.
6. Follow the instructions on the screen to complete the update. After the update is completed, remove the
disc from the optical drive.
Updating (flashing) the BIOS from your operating system
Note: Because Lenovo makes constant improvements to its Web sites, the Web page contents are subject
to change without notice, including the contents referenced in the following procedure.
To update (flash) the BIOS from your operating system, do the following:
2. Do the following to locate the downloadable files for your machine type:
a. In the Enter a product number field, type your machine type and click Go.
b. Click Downloads and drivers.
c. Select BIOS from the Refine results drop-down list box to easily locate all the BIOS related links.
d. Click the BIOS update link.
3. Click the TXT file that contains the instructions for updating (flashing) the BIOS from your operating
system.
4. Print these instructions. This is very important because these instructions will not be displayed on
the screen after the download begins.
5. Follow the printed instructions to download, extract, and install the update.
Recovering from a POST/BIOS update failure
If the power to your computer is interrupted while the POST and BIOS is being updated, your computer
might not restart correctly. If this happens, perform the following procedure to recover from the POST and
BIOS update failure. This procedure is commonly called Boot-block Recovery.
1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect
all power cords from electrical outlets and disconnect all cables that are connected to the computer.
4. Remove any cables that impede access to the Clear CMOS /Recovery jumper.
106 ThinkStation Hardware Maintenance Manual
5. Move the jumper from the standard position (pin 1 and pin 2) to the maintenance position (pin 2 and
pin 3).
6. Reconnect any cables that were disconnected and reinstall the PCI card if removed.
7. Reinstall the computer cover and reconnect the power cords for the computer and monitor to electrical
8. Turn on the computer and then insert the POST and BIOS update (flash update) disc into the optical
drive. Wait a few minutes. Then, the recovery session begins. The recovery session will take two to
three minutes. During this time, a warning message will be displayed and no action is needed from you.
9. After the recovery session is completed, there will be no video, and your computer will automatically
turn off.
10. Repeat step 1 through step 4.
11. Move the Clear CMOS /Recovery jumper back to the standard position (pin 1 and pin 2).
12. Reconnect any cables that were disconnected and reinstall the PCI card if removed.
13. Reinstall the computer cover and reconnect any cables that were disconnected.
14. Turn on the computer to restart the operating system.
Power management
Power management reduces the power consumption of certain components of the computer such as the
system power supply, processor, hard disk drives, and some monitors.
Automatic configuration and power interface (ACPI) BIOS
Being an ACPI BIOS system, the operating system is allowed to control the power management features
of the computer and the setting for Advanced Power Management (APM) BIOS mode is ignored. Not
all operating systems support ACPI BIOS mode.
Automatic Power-On features
The Automatic Power-On features within the Power Management menu allow you to enable and disable
features that turn on the computer automatically.
• Serial Port A Ring Detect: With this feature set to Enabled and an external modem connected to serial
port (COM1), the computer will turn on automatically when a ring is detected on the modem.
• PCI Modem Ring Detect: With this feature set to Enabled, the computer will turn on automatically
when a ring is detected on the internal modem.
• PCI Wake Up: This feature allows PCI cards that support this capability to wake the system.
• Wake Up on Alarm: You can specify a date and time at which the computer will be turned on
automatically. This can be either a single event or a daily event.
• Wake on LAN: If the computer has a properly configured token-ring or Ethernet LAN adapter card that is
Wake on LAN-enabled and there is remote network management software, you can use the Wake on LAN
feature. When you set Wake on LAN to Enabled, the computer will turn on when it receives a specific
signal from another computer on the local area network (LAN).
System memory speed
The Intel Xeon microprocessor families compatible with this ThinkStation computer feature an integrated
memory controller, which provides the microprocessor with direct access to the system memory. Because
of this design, the system memory speed will be determined by a number of factors, including the
microprocessor model and the type, speed, size (capacity), and number of DIMMs installed. Refer to the
following table for the information on the supported system memory speed for your own computer model.
Chapter 11. Additional service information 107
Table 2. DIMM type and speed: PC3-10600E
DIMM operating voltage
Microprocessor model
Memory frequency
Intel Xeon E5-2603, E5-2609
1066 MHz
Intel Xeon E5-2620, E5-2630/2630L,
E5-2637, E5-2640, E5-2643,
E5-2667, E5-2650/2650L, E5-2660,
E5-2665, E5-2670, E5-2680,
E5-2685, E5-2690
1.5 V
1333 MHz
Table 3. DIMM type and speed: PC3-10600R
DIMM operating voltage
Microprocessor model
Memory frequency
Intel Xeon E5-2603, E5-2609
1066 MHz
Intel Xeon E5-2620, E5-2630/2630L,
E5-2637, E5-2640, E5-2643 E5-2667,
E5-2650/2650L, E5-2660, E5-2665,
E5-2670, E5-2680, E5-2685, E5-2690
1.35 V, 1.5 V
1333 MHz
Table 4. DIMM type and speed: PC3-12800R
DIMM operating voltage
Microprocessor model
Memory frequency
Intel Xeon E5-2603, E5-2609
1066 MHz
Intel Xeon E5-2620, E5-2630/2630L,
E5-2637, E5-2640, E5-2643,
E5-2650/2650L, E5-2660, E5-2665,
E5-2667, E5-2670, E5-2680,
E5-2685, E5-2690,
1.35 V
1333 MHz
Intel Xeon E5-2603, E5-2609
1066 MHz
1333 MHz
Intel Xeon E5-2620, E5-2630/2630L,
E5-2640, E5-2667
1.5 V
E5-2637, E5-2643, E5-2650/2650L,
E5-2660, E5-2665, E5-2670,
E5-2680, E5-2685, E5-2690,
1600 MHz
108 ThinkStation Hardware Maintenance Manual
Appendix A. Notices
Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult
your local Lenovo representative for information on the products and services currently available in your
area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that
Lenovo product, program, or service may be used. Any functionally equivalent product, program, or service
that does not infringe any Lenovo intellectual property right may be used instead. However, it is the user's
responsibility to evaluate and verify the operation of any other product, program, or service.
Lenovo may have patents or pending patent applications covering subject matter described in this
document. The furnishing of this document does not give you any license to these patents. You can send
license inquiries, in writing, to:
Lenovo (United States), Inc.
1009 Think Place - Building One
Morrisville, NC 27560
U.S.A.
Attention: Lenovo Director of Licensing
LENOVO PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some jurisdictions do not allow
disclaimer of express or implied warranties in certain transactions, therefore, this statement may not apply
to you.
This information could include technical inaccuracies or typographical errors. Changes are periodically
made to the information herein; these changes will be incorporated in new editions of the publication.
Lenovo may make improvements and/or changes in the product(s) and/or the program(s) described in this
publication at any time without notice.
The products described in this document are not intended for use in implantation or other life support
applications where malfunction may result in injury or death to persons. The information contained in this
document does not affect or change Lenovo product specifications or warranties. Nothing in this document
shall operate as an express or implied license or indemnity under the intellectual property rights of Lenovo
or third parties. All information contained in this document was obtained in specific environments and is
presented as an illustration. The result obtained in other operating environments may vary.
Lenovo may use or distribute any of the information you supply in any way it believes appropriate without
incurring any obligation to you.
Any references in this publication to non-Lenovo Web sites are provided for convenience only and do not in
any manner serve as an endorsement of those Web sites. The materials at those Web sites are not part of
the materials for this Lenovo product, and use of those Web sites is at your own risk.
Any performance data contained herein was determined in a controlled environment. Therefore, the result
obtained in other operating environments may vary significantly. Some measurements may have been
made on development-level systems and there is no guarantee that these measurements will be the same
on generally available systems. Furthermore, some measurements may have been estimated through
extrapolation. Actual results may vary. Users of this document should verify the applicable data for their
specific environment.
© Copyright Lenovo 2012
109
Television output notice
The following notice applies to models that have the factory-installed television-output feature.
This product incorporates copyright protection technology that is protected by method claims of certain U.S.
patents and other intellectual property rights owned by Macrovision Corporation and other rights owners.
Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended
for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation.
Reverse engineering or disassembly is prohibited.
European conformance CE mark
The emission notices information is available in the ThinkStation Safety and Warranty Guide that came
with your computer.
Trademarks
The following terms are trademarks of Lenovo in the United States, other countries, or both:
Lenovo
The Lenovo logo
Rescue and Recovery
ThinkStation
ThinkVantage
Microsoft and Windows are trademarks of the Microsoft group of companies.
Intel and Intel Xeon are trademarks of Intel Corporation in the United States, other countries, or both.
Linux is a trademark of Linus Torvalds in the United States, other countries, or both.
Other company, product, or service names may be trademarks or service marks of others.
110 ThinkStation Hardware Maintenance Manual
Index
A
FRU part numbers 1, 55, 58, 63
H
B
battery, replacing 77, 102
C
I
changing
installing
installing options
CMOS, clearing 39
computer cover
removing 64
connectors
rear 56
L
locating components 56
connectors, controls, indicators
front 55
looking up part numbers 1, 55, 58, 63
M
memory module
D
drives
installing 91
bays 61
specifications 61
O
E
P
part numbers 1, 55, 58, 63
password
F
front
passwords
front bezel
FRU locations 56
erasing 39
© Copyright Lenovo 2012
111
slots 66
physical specifications 29
using
R
V
recovering
recovery
boot-block 106
replacing
battery 77, 102
S
security
selecting
setting
settings
changing 37
viewing 37
system board
locations 58
T
the BIOS, updating (flashing) 105–106
trademarks 110
U
updating
112 ThinkStation Hardware Maintenance Manual
|
Intel S5000PSL User Manual
JBL SIMPLY CINEMA SCS110 User Manual
JVC AV 29MX16 User Manual
JVC AV 1438 User Manual
Lenovo ThinkCentre 7174 User Manual
LG Electronics LG Life Good Computer Monitor W2284F User Manual
Moffat Turbofan E931 User Manual
Native Instruments B4 II User Manual
Nvidia Creative Graphics Blaster RIVA TNT2 User Manual
Palsonic 3400 User Manual