LG Electronics M227WA User Manual

OWNER’S MANUAL

M227WA

M237WA

Make sure to read the Safety Precautions before

using the product.

Keep the User's Guide(CD) in an accessible place

for furture reference.

See the label attached on the product and give the

information to your dealer when you ask for service.

PREPARATION

BACK PANEL INFORMATION

This is a simplified representation of the back panel. The image shown may be somewhat different from your

set.

COMPONENT

AV IN

AUDIO IN

(RGB/DVI)

RGB IN (PC)

HDMI IN

ANTENNA/

CABLE IN

DVI-D IN (PC)

RS-232C IN

(CONTROL & SERVICE)

S-VIDEO

Power Cord Socket

AV(Audio/Video) Input

Connect audio/video output from an external device

to these jacks.

This set operates on AC power. The voltage is indi-

cated on the Specifications page. Never attempt to

operate the set on DC power.

Antenna Input

Connect over-the-air signals to this jack.

HDMI Input

Connect a HDMI signal to HDMI IN.

Or DVI (VIDEO) signal to HDMI IN with DVI to HDMI

cable.

DVI-D Input(PC)

Connect the output from a PC.

RGB/DVI Audio Input

Connect the audio from a PC.

RS-232C IN (CONTROL & SERVICE) PORT

Connect to the RS-232C port on a PC.

S-Video Input

Connect S-Video out from an S-VIDEO device.

RGB Input (PC)

Connect the output from a PC.

Component Input

Connect a component video/audio device to these

jacks.

PREPARATION

STAND INSTALLATION

The image shown may be somewhat different from your set.

Carefully place the product screen side down on a

cushioned surface that will protect product and

screen from damage.

stand base

Insert the

into the product

Attach the monitor to the Stand Base by turning

the screw to the right.

* Turn the screw by using the screw handle

Screw

PREPARATION

STAND INSTALLATION

The image shown may be somewhat different from your set.

Carefully place the product screen side down on a

cushioned surface that will protect product and

screen from damage.

stand base

Insert the

into the product

Attach the monitor to the Stand Base by turning

the screw to the right.

* Turn the screw by using the screw handle

Screw

PREPARATION

DETACHING STAND

The image shown may be somewhat different from your set.

Place the set screen side down on a cushion or

soft cloth.

Detach the monitor to the Stand Base by turn-

ing the screw to the left.

Pull the stand base.

Turn the screw by using the screw handle

PREPARATION

DETACHING STAND

The image shown may be somewhat different from your set.

Place the set screen side down on a cushion or

soft cloth.

Detach the monitor to the Stand Base by turn-

ing the screw to the left.

Pull the stand base.

Turn the screw by using the screw handle

PREPARATION

WALL MOUNT: HORIZONTAL INSTALLATION

For proper ventilation, allow a clearance of 4 inches on each side and from the wall. Detailed installation

instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and

Setup Guide.

4 inches

DESKTOP PEDESTAL INSTALLATION

For proper ventilation, allow a clearance of 4 inches on each side and from the wall.

4 inches

PREPARATION

POSITIONING YOUR DISPLAY

The image shown may be somewhat different from your set.

Adjust the position of the panel in various ways for maximum comfort.

• Tilt range

°~ 18°

-6

-2°

LOCATION

Position your set so that no bright light or sunlight falls directly onto the screen. Care should be taken not to

expose the set to any unnecessary vibration, moisture, dust or heat. Also, ensure that the set is placed in a posi-

tion to allow a free flow of air. Do not cover the ventilation openings on the back cover.

If you intend to mount the set to a wall, attach Wall mounting interface (optional parts) to the back of the set.

When you install the set using the wall mounting interface (optional parts), attach it carefully so it will not drop.

- Be sure to use screws and a wall mount that meet VESA standards.

- Using screws longer than those recommended might damage the product.

- Using screws that do not meet VESA standards might either damage the product or result in it coming away from

the wall. We will not be held responsible for any damage resulting from failure to follow these instructions.

< Screw Mounting Interface Dimension >

M227WA : 100mm x 100mm hole spacing

M237WA : 75mm x 75mm hole spacing

Warning:

When adjusting the angle of the screen,do not put your

finger(s)in between the head of the monitor and the stand

body.You can hurt your finger(s).

PREPARATION

KENSINGTON SECURITY SYSTEM

- The product is equipped with a Kensington Security System connector on the back panel. Connect the

Kensington Security System cable as shown below.

- For detailed installation and use of the Kensington Security System, refer to the user’s guide provided with

the Kensington Security System.

http://www.kensington.com

For further information, contact

, the internet homepage of the

Kensington company. Kensington sells security systems for expensive electronic equipment such as note-

book PCs and LCD projectors.

NOTE

- The Kensington Security System is an optional accessory.

NOTES

a. If the product feels cold to the touch, there may be a small “flicker” when it is turned on.

This is normal, there is nothing wrong with product.

b. Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots.

However, they have no adverse effect on the monitor's performance.

c. Avoid touching the LCD screen or holding your finger(s) against it for long periods of time.

Doing so may produce some temporary distortion effects on the screen.

EXTERNAL EQUIPMENT SETUP

To prevent equipment damage, never plug in any power cords until you have finished connecting all equipment.

ANTENNA CONNECTION

For optimum picture quality, adjust antenna direction.

An antenna cable and converter are not supplied.

Multi-family Dwellings/Apartments

(Connect to wall antenna socket)

Wall

Antenna

Socket

ANTENNA/

CABLE IN

RF Coaxial Wire (75 ohm)

Outdoor

Antenna

(VHF, UHF)

Single-family Dwellings /Houses

(Connect to wall jack for outdoor antenna)

UHF

ANTENNA/

CABLE IN

Antenna

Signal

Amplifier

VHF

In poor signal areas, to get better picture quality, install a signal amplifier to the antenna as shown above.

If signal needs to be split for two sets, use an antenna signal splitter for connection.

EXTERNAL EQUIPMENT SETUP

To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.

The image shown may be somewhat different from your set.

HD RECEIVER SETUP

When connecting with a component cable

COMPONENT IN

Connect the SET-TOP outputs to the

VIDEO

sockets (Y P^BPR) on the set.

COMPO-

Connect the audio cable from the SET-TOP to

NENT IN AUDIO

sockets of the set.

INPUT

Component.

button to select

Press the

Signal

Component

480i/576i

480p/576p

720p/1080i

1080p

Yes

COMPONENT

EXTERNAL EQUIPMENT SETUP

When connecting with a HDMI

Connect the HDMI output of the digital set-top box to the

HDMI IN

jack on the set.

Press the INPUT button to select HDMI1 or HDMI2.

Signal

HDMI

480i/576i

480p/576p

720p/1080i

1080p

Yes

When connecting with a HDMI to DVI cable

HDMI IN

Connect the digital set-top box to

the set.

jack on

AUDIO IN

(RGB/DVI)

HDMI IN

Connect the audio output of the digital set-top box to

AUDIO IN (RGB/DVI)

the

jack on the set.

(

Turn on the digital set-top box. Refer to the owner’s

)

manual for the digital set-top box.

Press the INPUT button to select HDMI1 or HDMI2.

AUDIO

DVI OUTPUT

NOTE

^GHDMI Input does not support PC mode. If it is connected PC, the screen may not be displayed properly.

^GHDMI support PCM audio format only.

EXTERNAL EQUIPMENT SETUP

DVD SETUP

When connecting with a component cable

Connect the video output sockets (Y P^BPR) of the DVD to

COMPONENT IN VIDEO

the

sockets (Y PB PR) of the set.

COMPONENT

Connect the audio cable from the DVD to

IN AUDIO

sockets of the set.

INPUT

Component

Press the

button to select

PLAY

button on the DVD.

The DVD playback picture appears on the screen.

Component Input ports

To get better picture quality, connect a DVD player to the component input ports as shown below.

P^B

P^R

Component ports on the set

P^B

B-Y

P^R

R-Y

Video output ports

on DVD player

COMPONENT

EXTERNAL EQUIPMENT SETUP

When connecting HDMI cable

HDMI IN

Connect the HDMI output of the DVD to the

jack on the set.

Press the INPUT button to select HDMI1 or HDMI2.

NOTE

G Set can receive the video and audio signal simultaneously by using a HDMI cable.

G If the DVD player does not support Auto HDMI, you need to set the DVD output resolution appropriately.

GHDMI support PCM audio format only.

EXTERNAL EQUIPMENT SETUP

VCR SETUP

To avoid picture noise (interference), leave an adequate distance between the VCR and set.

Typically a still picture is shown on the VCR. If a user uses 4:3 picture format for a long time, an afterimage

may remain on the sides of the screen.

When connecting with an antenna

ANTENNA IN/

S-VIDEO

VIDEO

ANT OUT

CABLE IN

OUTPUT

SWITCH

ANT IN

Wall Jack

Antenna

Connect the RF out socket of the VCR to the aerial socket of the set.

Connect the aerial cable to the RF ANT IN socket of the VCR.

Store the VCR channel on a desired programme number using the ‘Manual

programme tuning’ section.

Select the programme number where the VCR channel is stored.

PLAY

Press the

button on the VCR.

EXTERNAL EQUIPMENT SETUP

When connecting with a RCA cable

AV IN

Connect the audio/video out sockets of the VCR to

AUDIO/VIDEO in sockets of the set.

Press the INPUT button to select AV.

Press the PLAY button on the VCR.

The VCR playback picture appears on the screen.

S-VIDEO

NOTE

If you have a mono VCR, connect the audio cable from the VCR to the AUDIO L/MONO jack of the set.

When connecting with an S-Video cable

Connect the S-Video socket of the VCR to the S-

VIDEO socket of the set.

AV IN

Connect the audio cable from the S-VIDEO VCR to the

AUDIO sockets of the set.

Press the INPUT button to select AV.

S-VIDEO

Press the PLAY button on the VCR.

The VCR playback picture appears on the screen.

EXTERNAL EQUIPMENT SETUP

PC SETUP

This product provides Plug and Play capability, meaning that the PC adjusts automatically to the set's settings.

When connecting with a D-sub 15 pin cable

RGB IN (PC)

AUDIO IN

(RGB/DVI)

Connect the signal cable from the RGB output socket of the

PERSONAL COMPUTER to the RGB IN(PC) of the set.

AUDIO IN

Connect the audio cable from the PC to the

(RGB/DVI)

jack of the set.

Press the INPUT button to select RGB PC.

Switch on the PC, and the PC screen appears on the set.

The set can be operated as a PC monitor.

AUDIO

RGB OUTPUT

NOTE

_GYou must use shielded signal interface cables (D sub 15 pin cable, DVI cable) with ferrite cores to maintain

standard compliance for the product.

EXTERNAL EQUIPMENT SETUP

When connecting with a DVI cable

DVI-D IN

Connect the DVI output of the PC to the

jack on the set.

AUDIO IN

(RGB/DVI)

DVI-D IN (PC)

AUDIO

Connect the audio cable from the PC to the

IN (RGB/DVI)

jack of the set.

AUDIO

DVI OUTPUT

NOTE

_GIf the set is cold, there may be a small “flicker” _GDo not press the LCD screen with your finger for

when the set is switched on. This is normal, there

is nothing wrong with the set.

a long time as this may produce some temporary

distortion effects on the screen.

_GIf possible, use the 1920x1080@60Hz video

mode to obtain the best image quality for your

LCD monitor. If used with other resolutions, some

scaled or processed pictures may appear on the

screen. The set has been preadjusted to the mode

1920x1080@60Hz.

Avoid keeping a fixed image on the set’s screen

for prolonged periods of time. The fixed image

may become permanently imprinted on the

screen; use a screen saver when possible.

_GSome dot defects may appear on the screen, like

Red, Green or Blue spots. However, this will have

no impact or effect on the monitor performance.

EXTERNAL EQUIPMENT SETUP

BACK COVER FOR WIRE ARRANGEMENT

Tie cables together with a cable management as

shown in the illustration.

Cable management

Tie cables together with a cable tie as shown in the

illustration.

Cable tie

EXTERNAL EQUIPMENT SETUP

RGB/DVI[PC]

Horizontal Vertical

Frequency(kHz) Frequency(Hz)

Resolution

720x400

640x480

31.468

31.469

37.500

37.879

46.875

48.363

60.123

67.500

63.981

79.976

64.674

65.290

75.000

66.587

800x600

1024 x 768

115 2 x 8 6 4

1280 x 1024

1680x1050

1600x1200

1920x1080

HDMI[DTV] supported mode

Horizontal

Frequency(kHz)

Vertical

Frequency(Hz)

Resolution

31.47

720x480/60p

31.5

720x576/50p

1280x720/50p

31.25

37.5

44.96

1280x720/60p

33.72

33.75

28.125

1920x1080/60i

1920x1080/50i

1920x1080/24p

33.75

56.25

67.43

67.5

1920x1080/30p

1920x1080/50p

1920x1080/60p

WATCHING TV /PROGRAMME CONTROL

REMOTE CONTROL KEY FUNCTIONS

When using the remote control, aim it at the remote control sensor on the set.

(Depends the country the remote control can be provided different.)

A TYPE

TV/PC Selects TV or PC mode.

Switches the set on.

POWER

INPUT

I/II

TV/PC

MUTE

POWER Switches the set on or off.

PIP

TEXT

INPUT External input mode rotates in regular sequence.

Switches the set on.

MUTE Switches the sound on or off.

PIP Switches the sub picture PIP, DW mode.

(Refer to the p.31)

TELETEXT These buttons are used for teletext.

BUTTONS For further details, see the ‘Teletext’ section. (Refer to

the p.52-54)

LIST

Q.VIEW

FAV Scroll through the programmed Favorite programme.

VOL

(Refer to the p.29)

I/II Selects the sound output.(Refer to the p.46)

0~9 number Selects a programme.

B TYPE

button

Selects numbered items in a menu.

POWER

LIST Displays the programme table.(Refer to the p.30)

INPUT

I/II

TV/PC

MUTE

Q.VIEW Returns to the previously viewed programme.

PIP

FAV

VOLUME UP Adjusts the volume.

/DOWN

Programme Selects a programme.

UP/DOWN

OK Button Accepts your selection or displays the current mode.

(Only

Double press the OK button, then Auto Config.

RGB-PC input)

LIST

Q.VIEW

VOL

WATCHING TV /PROGRAMME CONTROL

(Depends the country the remote control can be provided different.)

A TYPE

MENU Selects a menu. (Refer to the p.24)

SLEEP Sets the sleep timer. (Refer to the p.48)

ARC/* Selects your desired picture format.(Refer to the p.32,33)

MENU SLEEP ARC/

RETURN

RETURN Allows the user to move return one step in an interactive

HOLD

SIZE

MIX

TIME

application or other user interaction function.

INDEX

MODE

UPDATE

REVEAL

Colour These buttons are used for teletext or programme edit.

Buttons

(Refer to the p.28, 52-54)

Yellow key Scroll through the programmed Favorite programme.

(Only A Type)

HOLD Press the button to stop the automatically rotating of the

B TYPE

sub pages. Press the button again to continue the auto-

matic rotating again.

MENU SLEEP ARC/

RETURN

SIZE Press the button repeatedly to display the upper part,

the lower part and then to return to the normal page

size.

MIX Display the teletext pages superimposed on the TV pic-

ture. To switch the TV picture off press this button again.

Press this button to select a sub page number. The sub

TIME page number is displayed at the bottom of the screen. To

hold or change the sub page, press the RED/GREEN, D

/ E or NUMBER buttons. Press again to exit this func-

tion.

REVEAL Press the button to reveal/conceal the hidden informa-

tion, such as solutions to riddles and puzzles. Press this

button again to remove the information from the display.

INDEX To display the main index.

MODE The mode will be switched in the Teletext mode.

UPDATE Press the button to appear the TV programme. At the

top of screen indicates that you are still in the teletext

mode. Before interrupting teletext, you may select a page

number. When the page has been found, the information

line appears briefly on your screen. Press the button

again to reappear teletext.

Inserting batteries into remote control.

1. Take out the battery cap.

2. Insert the batteries with correct polarity (+/-).

3. Close the battery cap.

• Dispose of used batteries in the recycle bin to prevent

environmental pollution.

WATCHING TV /PROGRAMME CONTROL

TURNING ON THE SET

When your set is turned on, you will be able to use its features.

Firstly, connect the power cord correctly.

INPUT PR

POWER INPUT

To turn set on, press the

button on the set or press the

D / E

PR _{D / E}NUMBER(0 9)

buttons on the remote control and the set will switch on.

Initializing Guide

If the OSD (On Screen Display) is displayed on the screen after turning on the set, you can adjust the

Language Location Auto Tuning

Note:

a. It will automatically disappear after approx. 40 seconds unless a button is pressed.

b. “In-Store” mode is only for shop display and not for general customer use.

c. "Home” mode is the optimal setting for home environments, and is the set's default mode.

d. "In-Store" mode is the optimal setting for store environments. If a user modifies image quality data,

“In-Store” mode initializes the product to the image quality set by us after a certain period of time.

e. The mode (Home, In-Store) can be changed by executing Factory Reset in the Option menu.

PROGRAMME SELECTION

NUMBER

buttons to select a programme number.

Press the

D / E

VOLUME ADJUSTMENT

VOL _F

Press the

Gbutton to adjust the volume.

MUTE

If you wish to switch the sound off, press the

button.

MUTE or VOL _F

You can cancel the Mute function by pressing the

button.

WATCHING TV /PROGRAMME CONTROL

ON SCREEN MENUS SELECTION AND ADJUSTMENT

(

Your set's OSD On Screen Display may differ slightly from what is shown in this manual.

)

Press the

button and then

Press the G button and then

Ebutton to select a menu item.

Change the setting of an item in the sub or pull-down menu with

button to display each menu.

button.

You can move to a higher level menu by pressing the

Audio

Setup

Picture

Picture Mode

Sound Mode

Auto Volume

Balance

Auto Tuning

Colour Temperature

Manual Tuning

Programme Edit

Favourite Programme

TV Speaker

Advanced

Aspect Ratio

Picture Reset

Screen

DE F G OK RETURN

Time

Option

Language

PIP

Clock

Off Time

On Time

Sleep Timer

Auto Sleep

Key Lock

Set ID

DDC-CI

Power Indicator

Factory Reset

DE F G OK RETURN

• Press the MENU button to close the menu window.

• Press the RETURN button to move to the previous menu screen.

NOTE

The OSD (On Screen Display) function enables you to adjust the screen status conveniently since it provides graphi-

cal presentation.

In the teletext mode, menus are not displayed.

WATCHING TV /PROGRAMME CONTROL

AUTO PROGRAMME TUNING

Up to 100 TV stations can be stored by programme numbers (0 to 99). Once you have preset the

stations, you will be able to use the

programmed.

or NUMBER buttons to scan the stations you have

Stations can be tuned using automatic or manual modes.

All stations which can be received are stored by this method. It is

recommended that you use Auto tuning during installation of this set.

Setup

menu.

Auto Tuning

Press the

Setup

button and then

button to select the

To Set

Manual Tuning

Programme Edit

Favourite Programme

Press the G button and then D

Tuning

Ebutton to select

Auto

Press the G button and then D

Press the

Ebutton to select

System

DE F G OK RETURN

button to select a TV system menu;

BG: PAL B/G, SECAM B/G (Europe / East Europe / Asia /

NewZealand / M.East / Africa / Australia)

: PAL I/II (U.K. / Ireland / Hong Kong / South Africa)

DK: PAL D/K, SECAM D/K (East Europe / China / Africa / CIS)

M : NTSC M(Taiwan, Philippines, Myanmar)

Auto Tuning

System

Storage From

Press the

Ebutton to select

DE F G OK RETURN

Press the F

button or NUMBER buttons to select the initial

programme number. If you use NUMBER buttons, any

number under 10 is entered with a numeric ‘0’ in front of it, i.e.‘

for 5.

Auto Tuning

’

C 05

35%

Press the

Ebutton to select

Press the G button to begin auto tuning.

RETURN Stop

All receivable stations are stored.

RETURN

To stop auto tuning, press the

button.

When auto tuning is complete, the Programme edit menu appears

on the screen. See the Programme edit section to edit the stored

programme.

• Press the MENU button to close the menu window.

• Press the RETURN button to move to the previous menu screen.

WATCHING TV /PROGRAMME CONTROL

MANUAL PROGRAMME TUNING

Manual programme lets you manually tune and arrange the

stations in whatever order you desire.

Setup

button to select the

Press the

menu.

button and then

Press the G button and then D

Tuning

Ebutton to select

Manual

Setup

Auto Tuning

To Set

Manual Tuning

Programme Edit

Favourite Programme

Ebutton to select

Storage

Press the G button and then D

Press the F G button or NUMBER buttons to select the desired

programme number (0 to 99). If you use NUMBER buttons, any num-

ber under 10 is entered with a numeric ‘0’ in

front of it, i.e. ‘05’ for 5.

DE F G OK RETURN

Ebutton to select

System

Press the D

Manual Tuning

Storage

System

Band

Press the D

E button to select a TV system menu;

BG: PAL B/G, SECAM B/G (Europe / East Europe / Asia /

NewZealand / M.East / Africa / Australia)

Channel

Fine

: PAL I/II (U.K. / Ireland / Hong Kong / South Africa)

Name

DK: PAL D/K, SECAM D/K (East Europe / China / Africa / CIS)

M : NTSC M(Taiwan, Philippines, Myanmar)

Booster

DE F G OK RETURN

Ebutton to select

Band

Press the D

V/UHF

Press the G button and then D

Cable

E button to select

Press the D

Ebutton to select

Channel

You can select the desired programme number with the F

button or NUMBER buttons. If possible, select the programme

number directly with the number buttons. Any number under 10 is

entered with a numeric ‘0’ in front of it, i.e. ‘ ’ for 5.

Press the D

Ebutton to select

Press the F Gbutton to commence searching. If a station is

found the search will stop.

Press the

button to store it.

To store another station, repeat steps to

• Press the MENU button to close the menu window.

• Press the RETURN button to move to the previous menu screen.

WATCHING TV /PROGRAMME CONTROL

FINE TUNING

Normally fine tuning is only necessary if reception is poor.

Setup

menu.

Press the

Setup

button and then

button to select the

Auto Tuning

To Set

Manual Tuning

Programme Edit

Favourite Programme

Press the G button and then D

Tuning

Ebutton to select

Manual

button to select

Fine

Press the G button and then D

DE F G OK RETURN

Press the G button and then

best picture and sound.

button to fine tune for the

Manual Tuning

Storage

System

Band

Press the

button to store it.

Channel

Fine

Name

Booster

DE F G OK RETURN

ASSIGNING A STATION NAME

You can assign a station name up to five characters to each programme number.

Manual Tuning

Ebutton to select

Name

Press the G button and then D

Storage

System

Band

Ebutton. You can use a blank, ,

Press the G button and then D

Channel

Fine

, the number to and the alphabet to .

Name

-----

Press the F Gbutton to select the position and make

Booster

your choice of the second character, and so on.

DE F G OK RETURN

Press the

button to store it.

BOOSTER

In some models,

Booster

is an optional function. Only a set with

Manual Tuning

can perform this function.

If reception is poor select

Storage

System

Band

Booster

to On.

When the signal is strong, select “OFF”.

Channel

Fine

Name

Press the G button and then use

Ebutton to select

Booster

Off

Booster

DE F G OK RETURN

Ebutton to select

Press the G button and then use

Off

• Press the MENU button to close the menu window.

• Press the RETURN button to move to the previous menu screen.

WATCHING TV /PROGRAMME CONTROL

PROGRAMME EDIT

This function enables you to delete or skip stored programmes.

Also you can move some stations to other programme numbers

or copy a blank station data into the selected programme number.

menu.

Press the

Setup

button and then

button to select the

Setup

Auto Tuning

Manual Tuning

Programme Edit

Favourite Programme

To Set

Press the G button and then D

Edit

Programme

button to select

Press the G button to display the Programme edit menu.

Deleting a programme

DE F G OK RETURN

1. Select a programme to be deleted with the

button.

Programme Edit

2. Press the RED button twice.

The selected programme is deleted, all the following programmes

are shifted up one position.

BLN 03

C 09

Copying a programme

Delete

Move

Copy

Skip

1. Select a programme to be copied with the

button.

DE F G OK RETURN

2. Press the GREEN button.

All the following programmes are shifted down one position.

Moving a programme

1. Select a programme to be moved with the

button.

2. Press the YELLOW button.

3. Move the programme to the desired programme number with

the

Gbutton.

4. Press the YELLOW button again to release this function.

Skipping a programme number

1. Select a programme number to be skipped with the

Gbutton.

2. Press the BLUE button. The skipped programme turns to blue.

3. Press the BLUE button again to release the skipped programme.

When a programme number is skipped it means that you will be

unable to select it using the

Ebutton during normal TV

viewing. If you wish to select the skipped programme, directly

enter the programme number with the NUMBER buttons or

select it in the programme edit or table menu.

• Press the MENU button to close the menu window.

• Press the RETURN button to move to the previous menu screen.

WATCHING TV /PROGRAMME CONTROL

FAVOURITE PROGRAMME

This function lets you select your favourite programmes directly.

Setup

Auto Tuning

menu.

Press the

Setup

button and then

button to select the

Manual Tuning

Programme Edit

Favourite Programme

-- -----

Press the G button and then D

Programme

Ebutton to select

Favourite

Press the G button.

DE F G OK RETURN

Press the

Ebutton to select - - - - - - -.

Select a desired programme with the F Gbutton or NUMBER

buttons. Any number under 10 is entered with a numeric ‘0’in front

of it, i.e.‘ ’ for 5.

To store another programme, repeat steps to .

You can store up to 8 programmes.

• Press the MENU button to close the menu window.

• Press the RETURN button to move to the previous menu screen.

WATCHING TV /PROGRAMME CONTROL

SELECTING THE PROGRAMME LIST

You can check which programmes are stored in the memory by displaying the programme list.

Displaying programme list

LIST

Press the

button to display the Programme list menu.

The programme list appears on the screen.

One programme list contains ten programmes as shown.

NOTE

a. You may find some blue programmes. They have been set up to be

skipped by auto programming or in the programme edit mode.

b. Some programmes with the channel number shown in the

programme list indicate there is no station name assigned.

Selecting a programme in the programme list

button.

Select a programme with the D

Programme List

Then press the

button. The TV switches to the chosen programme number.

BLN 03

Paging through a programme list

There are 10 programme table pages in which contain 100 programmes some coun-

button repeatedly turns

tryes contain 200 programmes. Pressing the D

the pages.

F G DE OK RETURN

LIST

Press the

button to close the programme list window.

PICTURE CONTROL

WATCHING PIP (PICTURE-IN-PICTURE)

PIP lets you view 2 different inputs (sources) on your

PIP

TV screen at the same time.

One source will be large, and the other source will show

PIP

Off

PIP Input

a smaller inset image.

PIP function is available in the RGB-PC, DVI input only.

(It can support TV, AV mode)

PIP PR

C 07

Off

PIP Audio

PIP Size

Small

PIP Position

F G

RETURN

Watching PIP/Double Window

Each time you press the PIP button it will change to PIP -> DW1 -> DW2 -> PIP Off.

PIP Mode

DW1 Mode

DW2 Mode

PIP Off

Programme Selection for Sub Picture

Enter the PIP menu and then press the

Gbutton to select a programme for the sub picture.

The selected programme number is displayed just below RGB-PC or DVI input.

Input Source Selection for Sub Picture

Enter the PIP menu and then press the

button to select the PIP Input source for the sub picture.

(Sub picture can be selected only TV, AV)

Audio Source Selection for Sub Picture

Enter the PIP menu and then press the

button to select the PIP Audio source for the sub picture.

Sub Picture Size Adjustment (PIP mode only)

Enter the PIP menu and then press the D

Gbutton to adjust the sub picture size.

Moving the Sub Picture (PIP mode only)

Enter the PIP menu and then press the

Gbutton to adjust the sub picture position.

NOTE

A teletext function does not operate in PIP mode.

In PIP mode, below remote controller keys are not available.

* NUMBER, FAV, Q.VIEW

ARC function doesn’t operate DW1, DW2 mode.

PICTURE CONTROL

PICTURE SIZE (ASPECT RATIO)CONTROL

16:9, Original 4:3 14:9 Zoom1/2

Just Scan

You can watch the screen in various picture formats;

and

Just Scan works in the following mode:

Component (720p/1080i/1080p), HDMI (720p/1080i/1080p)

If a fixed image is displayed on the screen for a long time, that fixed image may become imprinted on the screen and

remain visible.

You can adjust the enlarge proportion using

This function works in the following signal.

Ebutton.

You can adjust

Aspect Ratio

Picture

in the menu.

16:9

4:3

•

The following selection will allow you to adjust the

picture horizontally, in linear proportion, to fill the

entire screen(useful for viewing 4:3 formatted

DVDs).

The following selection will allow you to view a pic-

ture with an original 4:3 aspect ration, grey bars will

appear on both the left and right hand of the

screen.

16:9

4:3

Original

•

14:9

•

When your set receives a wide screen signal it will

automatically change to the picture format to be

broadcast.

You can view a picture format of 14:9 or a general

TV programme in the 14:9 mode. The 14:9 screen

is viewed in the same way as in 4:3, but is magnified

to the left and right.

14:9 DE

Original

PICTURE CONTROL

Zoom1

Just Scan

•

The following selection will allow you to view the

picture without any alteration, while filling the entire

screen. However, the top and bottom of the picture

will be cropped.

Following Selection will lead to you view the picture

of best quality without loss of original picture in

high resolution image.

Just Scan

Zooml DE

Zoom2

•

Choose Zoom 2 when you wish the picture to be

altered, both horizontally extended and vertically

cropped. The picture adopting a compromise

between alteration and screen converage.

Zoom2 DE

NOTE

You can only select 4:3,16:9 (Wide) in Component, HDMI, RGB(PC) mode.

In HDMI/Component (over 720p)mode, Just Scan is available.

PICTURE CONTROL

PRESET PICTURE SETTINGS

Picture Mode-Preset

Picture Mode

Picture Mode adjusts the set for the best picture appearance. Select the preset value in the

menu based on the programme category.

Vivid, Standard, Cinema, Sport and Game are programmed for optimum picture reproduction at the factory

and cannot be changed.

Picture

menu.

Press the

Picture

button and then

button to select the

Picture Mode

Colour Temperature

Vivid

Standard

Cinema

Sport

Advanced

Ebutton to select

Picture

Press the G button and then D

Mode

Aspect Ratio

Picture Reset

Screen

Game

User1

User2

Ebutton to select

Vivid,

Press the G button and then D

Standard, Cinema, Sport, Game, User1 User2

DE F G OK RETURN

• Press the MENU button to close the menu window.

• Press the RETURN button to move to the previous menu screen.

PICTURE CONTROL

MANUAL PICTURE ADJUSTMENT

Picture Mode-User Mode

Backlight

Contrast

Brightness

Colour

Adjust the brightness of LCD panel to control the brightness of the screen.

Adjusts the difference between light and dark levels in the picture.

Increases or decreases the amount of white in the picture.

Adjusts intensity of all colours.

Sharpness

Adjusts the level of crispness in the edges between the light and dark areas of the picture. The lower

the level, the softer the image.

Tint

Adjusts the balance between red and green levels.

Picture

menu.

Press the

Picture

button and then

button to select the

Picture Mode

Colour Temperature

Vivid

Standard

Cinema

Sport

Advanced

Aspect Ratio

Picture Reset

Screen

Ebutton to select

Picture

Game

Press the G button and then D

Mode

User1

User2

Ebutton to select

User1

Press the G button and then D

DE F G OK RETURN

User2

User1

Press the G button and then D

picture option.

TV/AV/Component/HDMI

Colour, Sharpness and Tint

Ebutton to select the desired

Backlight

Contrast

Brightness

Colour

100^G

100

•

:Backlight, Contrast, Brightness,

Sharpness

Tint

RGB-PC/DVI-PC

:Backlight, Contrast, Brightness

•

Press the

Gbutton to make appropriate adjustments.

DE F G OK RETURN

User1

Backlight 100 F

Backlight

Contrast

100^G

100

Brightness

DE F G OK RETURN

<RGB-PC/DVI-PC>

• Press the MENU button to close the menu window.

• Press the RETURN button to move to the previous menu screen.

PICTURE CONTROL

Auto Colour Tone Control(Cool/Medium/Warm)

To initialize values (reset to default settings), select the Cool option.

Choose one of three automatic colour adjustments. Set to warm to enhance hotter colours such as red, or

set to cool to see less intense colours with more blue.

This menu is activated after selecting “User1” or “User2” in the Picture Mode.

Picture

Press the

the

button and then

button to select

Picture Mode

Colour Temperature

Cool

Picture

menu.

Medium

Warm

User

Advanced

Press the G button and then D

Temperature

Ebutton to select

Colour

Aspect Ratio

Picture Reset

Screen

Press the G button and then D

Ebutton to select

DE F G OK RETURN

Cool Medium Warm User

or .

either

Auto Colour Tone Control (9300K/6500K/sRGB)

(RGB-PC, DVI-PC mode only)

To initialize values (reset to default settings), select the 6500K option.

This menu is activated after selecting “User1” or “User2” in the Picture Mode.

Picture

Press the G button and then D

Ebutton to select either

Picture Mode

Colour Temperature

9300K, 6500K, sRGB User

9300K

6500K

sRGB

Advanced

Aspect Ratio

Picture Reset

Screen

User

DE F G OK RETURN

• Press the MENU button to close the menu window.

• Press the RETURN button to move to the previous menu screen.

NOTE

Auto colour tone is displayed with cool/medium/warm in the following mode.

RGB-PC(1080i), DVI(480i, 1080i)

PICTURE CONTROL

Colour Tone - User Mode

To adjust red, green, blue to any colour temperature you prefer.

This menu is activated after selecting “User1” or “User2” in the Picture Mode.

Picture

menu.

Press the

Picture

button and then

button to select the

Picture Mode

Colour Temperature

Cool

Medium

Warm

User

Advanced

Aspect Ratio

Picture Reset

Screen

Press the G button and then D

Temperature

Ebutton to select

Colour

Press the G button and then D

Ebutton to select

User

DE F G OK RETURN

Ebutton to select

Red Green

Press the G button and then D

Blue

Picture

Press the F

button to make appropriate adjustments.

Picture Mode

Colour Temperature

9300K

6500K

sRGB

Advanced

Aspect Ratio

Picture Reset

Screen

User

DE F G OK RETURN

<RGB-PC/DVI-PC>

User

....................

Red

0 ^G

Green

Blue

DE F G OK RETURN

........................

Red

0 F

• Press the MENU button to close the menu window.

• Press the RETURN button to move to the previous menu screen.

PICTURE CONTROL

- PICTURE IMPROVEMENT TECHNOLOGY

XD is LG electronic's unique picture improving technology to display a real HD source through an advanced digital

signal processing algorithm.

It is not possible to use this function in RGB-PC/DVI input.

User1 User2 Picture Mode

or of

This menu is activated after selecting the

Picture

Press the MENU button and then

Ebutton to select the

Picture Mode

Colour Temperature

Picture

menu.

Auto

Manual

Advanced

Ebutton to select

Aspect Ratio

Picture Reset

Screen

Press the G button and then D

Ebutton to select

Auto

Press the G button and then D

Manual

DE F G OK RETURN

* Manual Selection

XD Contrast

XD Colour

XD NR

Off

Low

High

Press the G button and then D

Ebutton to select XD

Contrast, XD Colour XD NR

Ebutton to select

Off Low

Press the G button and then D

High

DE F G OK RETURN

Off Low High Adaptive XD NR

or (Only ).

Select

XD Contrast : Optimises the contract automatically according to the brightness of the reflection.

XD Colour : Adjusts the colour of the reflection automatically to reproduce as close as possible to natural colours.

XD NR : Removes interference up to the point where it does not damage the original picture.

• Press the MENU button to close the menu window.

• Press the RETURN button to move to the previous menu screen.

PICTURE CONTROL

ADVANCED - GAMMA

High gamma values display whitish images and low gamma values display high contrast images.

It is not possible to use this function in RGB-PC/DVI input.

Picture

Picture Mode

menu.

Press the

Picture

button and then

button to select the

Colour Temperature

Advanced

To Set

Aspect Ratio

Picture Reset

Screen

Ebutton to select

Advanced

Press the G button and then D

Gamma

DE F G OK RETURN

Low,

Advanced

Medium High.

Gamma

Low

Medium

High

Film Mode

Black Level

ADVANCED - Film Mode

To set up for the best picture quality for viewing films.

DE F G OK RETURN

This feature operates only in TV, AV and Component 480i/576i mode.

Advanced

Gamma

Film

Press the

button and then

button to select

Off

Film Mode

Black Level

Mode

Press the

Off.

DE F G OK RETURN

ADVANCED - BLACK(DARKNESS) LEVEL

When you view a film this function adjust the set to best picture quality. Adjusting the contrast and the brightness of

the screen using the black level of the screen.

This function works in the following mode:

Advanced

RF(NTSC-M), AV(NTSC-M, NTSC 4.43), Component or HDMI.

Gamma

Film Mode

Black Level

Low

High

button to select

Black Level

Press the G button and then D

Low High.

Press the G button and then D

DE F G OK RETURN

Low : The reflection of the screen gets darker.

High : The reflection of the screen gets brighter.

• Press the MENU button to close the menu window.

• Press the RETURN button to move to the previous menu screen.

PICTURE CONTROL

PICTURE RESET

Returns to the default factory setting for Picture Mode, Colour Temperature, XD, Advanced, Aspect Ratio.

Picture

menu.

Picture Mode

Colour Temperature

Press the

Picture

button and then

button to select the

Advanced

Aspect Ratio

Picture Reset

Screen

Press the Gbutton and then D

Reset

Picture

button to select

To Set

Press the Gbutton to initialize the adjusted value.

DE F G OK RETURN

• Press the MENU button to close the menu window.

• Press the RETURN button to move to the previous menu screen.

PICTURE CONTROL

SCREEN SETUP FOR PC MODE

Auto Configure (RGB [PC] mode only)

Automatically adjusts picture position and minimizes image instability. After adjustment, if the image is

still not correct, your set is functioning properly but needs further adjustment.

Auto configure

This function is for automatic adjustment of the screen position, clock, and phase. The displayed image

will be unstable for a few seconds while the auto configuration is in progress.

1. Using OSD

Picture

Picture Mode

menu.

Press the

Picture

button and then use

button to select the

Colour Temperature

Advanced

Aspect Ratio

Picture Reset

Screen

Press the Gbutton and then use

Ebutton to select Screen

To Set

Ebutton to select

Auto

Press the Gbutton and then use

Config.

DE F G OK RETURN

Press the Gbutton to start Auto Config..

Screen

• When Auto config. has finished, OK will be shown on screen.

• If the position of the image is still not correct, try Auto adjustment

again.

Auto config.

Manual Config.

Resolution

Reset

To Set

• If picture needs to be adjusted again after Auto adjustment in RGB

Manual Config.

(PC), you can adjust the

DE F G OK RETURN

2. Using OK(Remocon or control key)

This function is available for RGB signals only.

• If you don’t want Auto Configure, do

Press the OK button.

OK)

Auto Config. (

not press

Press the OK button.

Auto in progress

For optimal display change

resolution to1920 x 1080

Auto in progress

<1920 x 1080 Resolution>

• Press the MENU button to close the menu window.

• Press the RETURN button to move to the previous menu screen.

PICTURE CONTROL

Manual Configure (Adjustment for screen Phase, Clock, Position)

(RGB [PC] mode only)

If the picture is not clear after auto adjustment and especially if characters are still trembling, adjust the picture phase

manually.

Clock

To correct the screen size, adjust

It’s not available to use Phase, Clock function in COMPONENT

(480i/480p/576i/576p/720p/1080i/1080p), HDMI (480p/576p/720p/1080i/1080p).

Clock

Phase

This function is to minimize any vertical bars or stripes visible on the screen background the horizon-

tal screen size will also change.

This function allows you to remove any horizontal noise and clear or sharpen the image of characters.

Picture

Picture menu.

Press the

button and then use

button to select the

Picture Mode

Colour Temperature

Advanced

Press the Gbutton and then use

Ebutton to select Screen

Aspect Ratio

Picture Reset

Screen

To Set

Press the

Config.

button and then use

Ebutton to select

Manual

DE F G OK RETURN

Press the Gbutton and then use

Ebutton to select

Phase

Clock

H-Position or V-Position

Screen

Auto config.

Manual Config.

Resolution

Reset

Press the F Gbutton to make appropriate adjustments.

Phase

Clock

H-Position

V-Position

DE F G OK RETURN

• Press the MENU button to close the menu window.

• Press the RETURN button to move to the previous menu screen.

PICTURE CONTROL

Selecting Resolution

To view a normal picture, match the resolution of RGB mode and selection of Resolution.

This function works in the following mode: RGB-PC input mode.

Picture

Picture Mode

menu.

Press the

Picture

button and then use

button to select the

Colour Temperature

Advanced

Aspect Ratio

Picture Reset

Screen

Press the Gbutton and then use

Ebutton to select

Screen

To Set

Press the Gbutton and then use

Resolution

Ebutton to select

DE F G OK RETURN

Screen

Press the Gbutton and then use

Ebutton to select the

Auto config.

Manual Config.

Resolution

Reset

desired Resolution.

1400 x 1050

1680 x 1050

DE F G OK RETURN

Initializing (Reset to original factory settings)

This function operates in current mode.

To initialize the adjusted value

Screen

button to select

Reset

Press the Gbutton and then use

Auto config.

Manual Config.

Resolution

Reset

Press the Gbutton.

To Set

DE F G OK RETURN

• Press the MENU button to close the menu window.

• Press the RETURN button to move to the previous menu screen.

SOUND CONTROL

PRESET SOUND SETTINGS-SOUND MODE

You can select your preferred sound setting; SRS TS XT, Clear Voice, Standard, Music, Cinema, Sport or Game and you can

also adjust the frequency of the equalizer.

Sound Mode lets you enjoy the best sound without any Special adjustment as the sets the appropriate sound options based

on the programme content.

TruSurround XT(SRS TS XT) Clear Voice Standard Music Cinema Sport

Game

are preset for optimum

and

sound quality at the factory and are not adjustable.

Audio

menu.

Press the

Audio

button and then

button to select the

Sound Mode

Auto Volume

Balance

SRS TS XT

Clear Voice

Standard

Music

TV Speaker

Press the G button and then D

Mode

Ebutton to select

Sound

Cinema

Sport

Game

User

Ebutton to select

SRS TS XT

Press the G button and then D

DE F G OK RETURN

Clear Voice Standard Music Cinema Sport, Game

User

SOUND SETTING ADJUSTMENT -USER MODE

Adjusting the audio equalizer.

Audio

Sound Mode

Auto Volume

Balance

SRS TS XT

Clear Voice

Standard

Music

Ebutton to select

User

Press the G button and then D

TV Speaker

Cinema

Sport

Press the G button.

Game

User

Select a frequency band by pressing the F Gbutton.

DE F G OK RETURN

Set the desired sound level with the

button.

User

0.1 0.5 1.5 5.0 10 kHz

DE F G OK RETURN

• Press the MENU button to close the menu window.

• Press the RETURN button to move to the previous menu screen.

is a trademark of SRS Labs, Inc.

TruSurround XT technology is incorporated under license from SRS Labs, Inc.

SOUND CONTROL

AUTO VOLUME LEVELER

Auto Volume automatically remains on the same level of volume if you change programmes.

Audio

menu.

Press the

Audio

button and then

button to select the

Sound Mode

Auto Volume

Balance

Off

TV Speaker

Press the G button and then D

Ebutton to select

Auto

Volume

Press the G button and then D

button to select

On Off

or .

DE F G OK RETURN

BALANCE

You can adjust the sound balance of the speakers to the preferred levels.

Audio

Ebutton to select

Balance

Press the G button and then D

Sound Mode

Auto Volume

Balance

Press the G button and then F Gbutton to make desired adjust-

...........

TV Speaker

ment.

DE F G OK RETURN

TV SPEAKERS ON/OFF SETUP

You can adjust the internal speaker status.

In TV, AV, COMPONENT and HDMI mode, internal speaker audio can be operational even though there is no video signal.

If you wish to use an external hi-fi system, turn off the TV internal speakers.

Audio

Press the G button and then D

Ebutton to select

TV Speaker

Sound Mode

Auto Volume

Balance

Press the G button and then D

Ebutton to select

Off

TV Speaker

On Off

DE F G OK RETURN

• Press the MENU button to close the menu window.

• Press the RETURN button to move to the previous menu screen.

SOUND CONTROL

I/II

Stereo/Dual Reception

When a programme is selected, the sound information for the station appears with the programme number and station

name.

I/II

Press the

button and then

button.

Broadcast

Mono

On Screen Display

MONO

Stereo

STEREO

Dual

DUAL I, DUAL II, DUAL I+II

Mono sound selection

If the stereo signal is weak in stereo reception, you can switch to mono. In mono reception, the clarity of sound is improved.

To switch back to stereo.

Language selection for dual language broadcast

If a programme can be received in two languages (dual language), you can switch to DUAL I, DUAL II or DUAL I+II.

DUAL I

Sends the primary broadcast language to the loudspeakers.

Sends the secondary broadcast language to the loudspeakers.

Sends a separate language to each loudspeaker.

DUAL II

DUAL I+II

NICAM Reception

If the set is equipped with a receiver for NICAM reception,high quality NICAM (Near Instantaneous Companding Audio

Multiplex)digital sound can be received.

Sound output can be selected according to the type of broadcast received.

When NICAM MONO is received, you can select NICAM MONO or FM MONO.

When NICAM stere is received, you can select NICAM STEREO or FM MONO.

If the stereo signal is weak,switch to FM MONO.

When NICAM dual is received, you can select NICAM DUAL I, NICAM DUAL II or

NICAM DUAL I+II or FM MONO.

Speaker Sound Output Selection

In AV, Component, RGB-PC, HDMI and DVI mode, you can select output sound for the left and right loudspeakers.

Select the sound output.

L+R: Audio signal from audio L input is sent to the left loudspeaker and audio signal from audio R input is sent to

the right loudspeaker.

L+L:

Audio signal from audio L input is sent to left and right loudspeakers.

R+R: Audio signal from audio R input is sent to left and right loudspeakers.

TIME SETTING

CLOCK SETUP

You must set the time correctly before using on/off timer function.

If current time setting is erased by a power failure or the set is unplugged, reset the clock.

Time

menu.

Press the

Time

button and then

button to select the

Clock

- -

Off Time

On Time

Sleep Timer

Auto Sleep

Ebutton to select

Ebutton to set the hour.

Ebutton to set the minute.

Clock

Press the G button and then D

DE F G OK RETURN

AUTO ON/OFF TIME SETTING

The Off time function automatically switches the set to standby at a preset time.

Two hours after the set is switched on by the on time function it will automatically switch off unless a button has been

pressed.

Once the on time/off time is set, these functions operate daily at the preset time.

The Off time function overrides the On timer function if both are set to the same time.

Time

Press the G button and then D

Ebutton to select

On Off

Clock

Time

- -

Off Time

On Time

Sleep Timer

Auto Sleep

On Off Time

Off

• To cancel

function, select

Press the G button and then D

Ebutton to set the hour.

Press the G button and then D

minutes.

Ebutton to set the

DE F G OK RETURN

For On Time function only

Time

Clock

Programme

•

: Press the Gbutton and then

button to

Off Time

On Time

Sleep Timer

Auto Sleep

select the programme.

--:--

Volume

•

: Press the Gbutton and then

button to adjust

Vol.

Off

volume level at switch-on.

DE F G OK RETURN

• Press the MENU button to close the menu window.

• Press the RETURN button to move to the previous menu screen.

TIME SETTING

SLEEP TIMER SETTING

You do not have to remember to switch the set off before you go to sleep. The sleep timer automatically switches the set

off after the preset time has elapsed.

Time

Clock

menu.

Press the

Time

button and then

button to select the

Off Time

On Time

Off

Sleep Timer

Auto Sleep

Ebutton to select

Sleep

Press the G button and then D

Timer

Press the G button and then D

Ebutton to set the minute.

DE F G OK RETURN

NOTE

When you switch the set off, the set releases the preset sleep timer.

AUTO SHUT-OFF SETTING

If the set is switched on and there is no input signal, it will switch off automatically after 10 minutes.

Time

Ebutton to select

Auto Sleep

Clock

Press the G button and then D

Off Time

On Time

Sleep Timer

Auto Sleep

button to select

On Off

or .

Press the G button and then D

Off

DE F G OK RETURN

• Press the MENU button to close the menu window.

• Press the RETURN button to move to the previous menu screen.

OPTION SETTING

ON-SCREEN MENU LANGUAGE SELECTION

Installation guide menu appears on set screen when it is turned on for the first time.

Press the D

G button and then,

button to

Option

select your desired language.

Language

PIP

To Set

Key Lock

Set ID

DDC-CI

* If you want to change Language selection

Power Indicator

Factory Reset

Press the

button and then use

button to

OPTION

select the

menu.

DE F G OK RETURN

Press the G button and then use

Language

button to select

Gbutton to

Press the Gbutton and then use

select your desired language. The menus can be shown on

the screen in the selected language.

Press the

button.

• Press the MENU button to close the menu window.

• Press the RETURN button to move to the previous menu screen.

NOTE

^GIf you don’t finish set up Installation Guide by pressing RETURN button or time out of OSD (On Screen Display)

display, it will continuously appear until completing set up whenever the set is turned on.

OPTION SETTING

KEY LOCK

The set can be set so that the remote control is needed to control it.

This feature can be used to prevent unauthorized viewing.

This set is programmed to remember which option it was last set to even if you turn the set off.

Option

menu.

Press the

Option

button and then

button to select the

Language

PIP

Key Lock

Set ID

Off

Press the Gbutton and then D

Ebutton to select

Key Lock

DDC-CI

Power Indicator

Factory Reset

Ebutton to select

On Off

Press the Gbutton and then D

DE F G OK RETURN

NOTE

In Key Lock ‘On’, if the set is turned off, press the r / I, INPUT, PR

INPUT PR

button on the set or POWER,

or NUMBER buttons on the remote control.

With the Key Lock On, the display

pressed while using the set.

Key Lock On

‘ ’ appears on the screen if any button on the right side of set is

DDC CI(Only RGB, DVI mode)

DDC/CI (Display Data Channel Command Interface) is a communication protocol for communications between

PC and set.

DDC/CI makes it possible to adjust and setup detailed functions on PC instead of the set OSD

Set can be adjusted with PC by connecting communication between PC and set when DDC/CI is ON, and set

cannot be adjusted with PC because communication between PC and set is disconnected when DDC/CI is OFF.

Option

Press the G button and then D

Ebutton to select

DDC-CI.

Language

PIP

Key Lock

Set ID

button to select

On Off

or .

Press the G button and then D

Off

DDC-CI

Power Indicator

Factory Reset

DE F G OK RETURN

• Press the MENU button to close the menu window.

• Press the RETURN button to move to the previous menu screen.

OPTION SETTING

POWER INDICATOR

It helps you control LED when power is turned on.

Option

menu.

Press the

Option

button and then

button to select the

Language

PIP

Key Lock

Set ID

DDC-CI

Press the G button and then D

indicator.

Ebutton to select

Power

Off

Power Indicator

Factory Reset

button to select

On Off

or .

Press the G button and then D

DE F G OK RETURN

FACTORY RESET

Use to quickly reset all the menu options to their original factory preset values.

The function deletes all TV programmes.

Option

Press the Gbutton and then D

Ebutton to select

Factory

Language

PIP

Reset

Key Lock

Set ID

Yes No

Press the Gbutton and then F Gbutton to select

DDC-CI

Power Indicator

Factory Reset

To Set

DE F G OK RETURN

Factory Reset

Yes

F G OK RETURN

• Press the MENU button to close the menu window.

• Press the RETURN button to move to the previous menu screen.

TELETEXT

This feature is not available in all countries.

Teletext is a free service broadcast by most TV stations which gives up-to-the-minute information on news, weather, televi-

sion programmes, share prices and many other topics.

The teletext decoder of this TV can support the SIMPLE, TOP and FASTEXT systems. SIMPLE (standard teletext) consists

of a number of pages which are selected by directly entering the corresponding page number. TOP and FASTEXT are more

modern methods allowing quick and easy selection of teletext information.

SWITCH ON/OFF

TEXT

Press the

button to switch to teletext. The initial page or last page viewed appears on the screen.

Two page numbers, TV station name, date and time are displayed on the screen headline. The first page number indicates your

selection, while the second shows the current page displayed.

TEXT RETURN

Press the

button to switch off teletext. The previous mode reappears.

SIMPLE TEXT

APage selection

Enter the desired page number as a three digit number with the NUMBER buttons. If during selection you press a wrong

number, you must complete the three digit number and then re-enter the correct page number.

The

button can be used to select the preceding or following page.

AProgramming a colour button in LIST mode

If the TV is in SIMPLE text,TOP text or FASTEXT mode, press the

butto to switch to LIST mode.

Four teletext page umbers of your choice can be colour coded and easily selected by pressing the corresponding coloured

button on the remote control handset.

Press a coloured button.

Using the NUMBER buttons,select the page you wish to programme.

Press the OK button. The selected page is stored as the selected page umber, blinking once to confirm this.

From now on, you can select this page with the same coloured button.

The three other coloured buttons are programmed in this way.

TELETEXT

TOP TEXT

The user guide displays four fields-red, green, yellow and blue at the bottom of the screen. The yellow field denotes the next

group and the blue field indicates the next block.

ABlock / group / page selection

With the blue button you can progress from block to block.

Use the yellow button to proceed to the next group with automatic overflow to the next block.

With the green button you can proceed to the next existing page with automatic overflow to the next group.

Alternatively the

button can be used.

The red button return to the previous selection. Alternatively the

button can be used.

ADirect page selection

As with SIMPLE teletext mode, you can select a page by entering it as a three digit number using the NUMBER buttons in

TOP mode.

FASTEXT

The teletext pages are colour coded along the bottom of the screen and are selected by pressing the corresponding coloured

button.

APage selection

Press the

button to select the index page.

You can select the pages which are colour coded along the bottom line with corresponding coloured buttons.

As with SIMPLE teletext mode, you can select a page by entering its three digit page number with the NUMBER buttons in

FASTEXT mode.

The

button can be used to select the preceding or following page.

TELETEXT

SPECIAL TELETEXT FUNCTIONS

TIME

When viewing a TV programme, press this button to display the time at the top right hand corner of the screen. Press this but-

ton again to remove the display. In the teletext mode, press this button to select a sub page number. The sub page number is

displayed at the bottom of the screen. To hold or change the sub page, press the RED/GREEN,

or NUMBER but-

tons.

Press again to exit this function.

SIZE

Selects double height text.

Press this button to enlarge the top half of the page.

Press this button again to enlarge the bottom half of the page.

Press this button again to return to the normal display.

UPDATE

Displays the TV picture on the screen while waiting for a new teletext page. The display will appear at the top left hand corner

of the screen. When the updated page is available then display will change to the page number. Press this button again to view

the updated teletext page.

REVEAL

Press this button to display concealed information, such as solutions to riddles or puzzles.

Press this button again to remove the information from the display.

INDEX

Select the each index page.

HOLD

Stops the automatic page change which will occur if a teletext page consists of 2 or more sub pages. The number of sub pages

and the sub page displayed is, usually, shown on the screen below the time. When this button is pressed the stop symbol is dis-

played at the top left-hand corner of the screen and the automatic page change is inactive. To continue press this button again.

MIX

Displays the teletext pages superimposed on the TV picture.

To switch the TV picture off press this button again.

APPENDIX

TROUBLESHOOTING

The operation does not work normally.

Check to see if there is any object between the product and the remote control caus-

ing obstruction. Ensure you are pointing the remote control directly at the set.

Ensure that the batteries are installed with correct polarity (+ to +, - to -).

Ensure that the correct remote operating mode is set: TV, VCR, etc.

Install new batteries.

The remote control

doesn’t work

Is the sleep timer set?

Power is suddenly

turned off

Check the power control settings. Power interrupted.

No broadcast on station tuned with Auto sleep activated.

The video function does not work.

Check whether the product is turned on.

Try another channel. The problem may be with the broadcast.

Is the power cord inserted into wall power outlet?

Check your antenna direction and/or location.

No picture &No sound

Test the wall power outlet, plug another product’s power cord into the outlet

where the product’s power cord was plugged in.

Picture appears slowly

after switching on

This is normal, the image is muted during the product startup process. Please

contact your service centre, if the picture has not appeared after five minutes.

Adjust Colour in menu option.

Keep a sufficient distance between the product and the VCR.

Try another channel. The problem may be with the broadcast.

Are the video cables installed properly?

No color, poor colour,

or poor picture

Activate any function to restore the brightness of the picture.

Horizontal/vertical bars

or picture shaking

Check for local interference such as an electrical appliance or power tool.

Station or cable product experiencing problems, tune to another station.

Station signal is weak, reorient antenna to receive weaker station.

Check for sources of possible interference.

Poor reception on

some channels

Lines or streaks

in pictures

Check antenna (Change the direction of the antenna).

APPENDIX

The audio function does not work.

Press the VOL

button.

Sound muted? Press MUTE button.

Picture OK & No sound

Try another channel. The problem may be with the broadcast.

Are the audio cables installed properly?

No output from one

of the speakers

Adjust Balance in menu option.

Unusual sound from

inside

A change in ambient humidity or temperature may result in an unusual noise

when the product is turned on or off and does not indicate a problem with

the product.

the product

Only RGB/DVI mode applied

No image is displayed.

Adjust brightness and contrast again.

Power is on, power indic-

tor is blue but the screen

appears extremely dark.

Does the power indica-

tor look amber?

If the product is in power saving mode, move the mouse or press any key.

Does the ‘Out of range’

message appear?

The signal from the PC (Video card) is out of the vertical or horizontal

frequency range of the product.

Adjust the frequency range by referring to the Specifications in this user’s guide.

The signal cable between PC and product is not connected. Check the signal cable.

Press the ‘INPUT’ button in the remote control to check the input signal.

Does the ‘Check signal

cable’ message appear?

APPENDIX

‘Unknown Product’ message appears when the product is connected.

Install the product driver, which is provided with the product, or download it

from the web site.

Did you install the driver?

(http://www.lge.com)

See if the plug_&_play function is supported by referring to the video card

user’s guide.

After-image appears on the product.

If you use a fixed image for a long time, the pixels may be damaged quickly.

After-image appears when

the product is turned off.

Use the screen saver function.

Screen color is abnormal.

Set screen color resolution to more than 24 bits (true color)

Screen has poor color res-

oluion (16_colors).

Select control Panel-Display-Settings-Color Table menu in Windows.

Screen color is unstable

or mono color.

Check the connection status of the signal cable.

Several pixels (red, green, white or black color) may appear on the screen,

which can be attributable to the unique characteristics of the LCD panel.

It is not a malfunction of the LCD.

Do back spots appear on

the screen?

Only RGB mode applied

The screen image looks abnormal.

Adjust the Position menu in OSD.

Is the screen position

wrong?

See if the video card resolution and frequency are supported by the product.

If the frequency is out of range, set to the recommended resolution in the

Control Panel-Display-Setting menu.

Do thin lines appear on

the background screen?

Adjust the Clock menu in OSD.

Adjust the Phase menu in OSD.

Horizontal noise appears

or the characters look

blurred.

APPENDIX

MAINTENANCE

Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you can

enjoy your new set.

Caution: Be sure to turn the power off and unplug the power cord before you begin any cleaning.

Cleaning the Screen

To keep the dust off your screen for a while, wet a soft cloth in a mixture of lukewarm water and a little fab-

ric softener or dishwashing detergent. Wring the cloth until it’s almost dry, and then use it to wipe the

screen.

Make sure the excess water is off the screen, and then let it air-dry before you turn on your set.

Cleaning the Cabinet

To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.

Please be sure not to use a wet cloth.

Extended Absence

CAUTION

_GIf you expect to leave your set dormant for a long time (such as a vacation), it’s a good idea to unplug

the power cord to protect against possible damage from lightning or power surges.

APPENDIX

PRODUCT SPECIFICATIONS

Screen Type

Pixel Pitch

21.53 inches Wide (546.86 mm) TFT (Thin Film Transistor)

LCD (Liquid Crystal Display) Panel

LCD Panel

Visible diagonal size: 546.86 mm

0.248(H) x 0.248(V) mm

Max. Resolution

1920 X 1080 @60 Hz

Video Signal

Recommended Resolution

Horizontal Frequency

Vertical Frequency

Synchronization Type

1920 X 1080 @60 Hz

30 - 83 kHz

56 - 75 Hz

Separate Sync, Digital

S-VIDEO, CVBS, TV, D-Sub Analog, DVI-D, HDMI, PC Audio In, Component

Input Connector

Power

Rated Voltage

AC100-240V~ 50/60 Hz 0.9A

Power Consumption

On Mode

Sleep Mode

Off Mode

: 45W (typ.)

1W (RGB)

Tilt

-5 ~ 15 °

Tilt Range

519.8 x 400.5 x 193.2 mm (20.46 x 15.77 x 7.61 inches)

4.7 kg / 10.36 lbs

Dimensions (Width x Height x Depth)

Weight

Operating Temperature

10 ~ 35°C

20 ~ 80%

-10 ~ 60°C

5 ~ 90%

Operating Humidity

Environmental

conditions

Storage Temperature

Storage Humidity

The specifications shown above may be changed without prior notice for quality improvement.

APPENDIX

PRODUCT SPECIFICATIONS

Screen Type

Pixel Pitch

23 inches Wide (584.2 mm) TFT (Thin Film Transistor)

LCD (Liquid Crystal Display) Panel

LCD Panel

Visible diagonal size : 584.2 mm

0.265(H) x 0.265(V) mm

1920 X 1080 @60 Hz

Video Signal

Max. Resolution

1920 X 1080 @60 Hz

Recommended Resolution

Horizontal Frequency

Vertical Frequency

30 - 83 kHz

56 - 75 Hz

Separate Sync, Digital

Synchronization Type

S-VIDEO, CVBS, TV, D-Sub Analog, DVI-D, HDMI, PC Audio In, Component

Input Connector

Power

Rated Voltage

AC 100-240V ~ 50/60 Hz 1.0A

Power Consumption

On Mode

Sleep Mode

Off Mode

: 50W (typ.)

1W (RGB)

Tilt

Tilt Range

-5 ~ 15 °

560.8 x 427 x 193.2 mm (22.08 x 16.81 x 7.61 inches)

5.6 kg / 12.35 lbs

Dimensions (Width x Height x Depth)

Weight

10 ~ 35°C

Operating Temperature

20 ~ 80%

Operating Humidity

Environmental

conditions

-10 ~ 60°C

5 ~ 90%

Storage Temperature

Storage Humidity

The specifications shown above may be changed without prior notice for quality improvement.

APPENDIX

IR CODES

1. How to Connect

Connect your wired remote control to the Remote Control port on the set.

2. Remote Control IR Codes

Output waveform

Single pulse, modulated with 37.917KHz signal at 455KHz

Carrier frequency

FCAR = 1/TC = fOSC/12

Duty ratio = T1/TC = 1/3

Configuration of frame

1st frame

Lead code

Low custom code

High custom code

Data code

C0 C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7

Repeat frame

Lead code

Repeat code

9 ms

4.5 ms

Repeat code

0.55 ms

9 ms

2.25 ms

Bit description

Bit ”0”

Bit ”1”

0.56ms

1.12ms

2.24ms

Frame interval: Tf

The waveform is transmitted as long as a key is depressed.

Tf=108ms @455KHz

APPENDIX

Code

(Hexa)

Function

(Hexa)

Note

Function

Note

MUTE

LIST

R/C Button

ARC

R/C Button

R/C Button (Power On/Off)

R/C Button

INPUT

POWER

RETURN

VOL _F

VOL _G

PR _D

10 ~ 19 Number Key 0 ~ 9 R/C Button

Q.VIEW

TEXT

TIME

R/C Button

SIZE

UPDATE

INDEX

HOLD

REVEAL

MIX

PR _E

OK( )

RED

GREEN

YELLOW

BLUE

MODE

I/II

SLEEP

FAV

TV/PC

PIP

APPENDIX

EXTERNAL CONTROL THROUGH RS-232C

Connect the RS-232C input jack to an external control device (such as a computer or an A/V control

system) and control the set’s functions externally.

Connect the serial port of the control device to the RS-232C jack on the set back panel.RS-232C

connection cables are not supplied with the set.

RS-232C Setup

RS-232C IN

(CONTROL)

Type of Connector; D-Sub 9-Pin Male

No.

Pin Name

No connection

(

)

RXD Receive data

(

)

TXD Transmit data

(

)

DTR DTE side ready

GND

(

)

DSR DCE side ready

(

)

RTS Ready to send

(

)

CTS Clear to send

No Connection

APPENDIX

RS-232C Configurations

(

)

(

)

7-Wire Configurations Standard RS-232C cable

3-Wire Configurations Not standard

SET

RXD

TXD

GND

DTR

DSR

RTS

TXD

RXD

GND

DSR

DTR

CTS

RTS

RXD

TXD

GND

DTR

DSR

RTS

TXD

RXD

GND

DTR

DSR

RTS

CTS

D-Sub 9

Set ID

- Use this function to specify a set ID number.

- Refer to ‘Real Data Mapping 1’. See page 68.

Option

menu.

Press the

Option

button and then use

button to select the

Language

PIP

Key Lock

Set ID

Ebutton to select

Set ID

DDC-CI

Press the G button and then use

Power Indicator

Factory Reset

Set ID

button to adjust

Press the G button and then use

to choose the desired Set ID number.

• The adjustment range of SET ID is 1~ 99.

DE F G OK RETURN

Communication Parameters

(

)

Baud rate : 9600 bps UART

Stop bit : 1 bit

Data length : 8 bits

Parity : None

Communication code : ASCII code

Use a crossed (reverse) cable.

APPENDIX

Command Reference List

DATA

(Hexadecimal)

DATA

(Hexadecimal)

COMMAND1 COMMAND2

01. Power

00 ~ 01

14. Colour Temperature

15. Red Adjustment

16. Green Adjustment

17. Blue Adjustment

18 . Abnormal Status

19. Auto Configure

20. Equalize

Refer to p.67

00 ~ 3C

02. Aspect Ratio

03. Screen Mute

04. Volume Mute

05. Volume Control

06. Contrast

Refer to p.66

00 ~ 01

00 ~ 64

00 ~ 01

07. Brightness

08. Colour

Refer to p.68

00 ~ 01

Key Code

Refer to p.68

21. Tune Command

09. Tint

22. Channel Skip

23. Key

10. Sharpness

11. OSD Select

24. Input select (Main)

12. Remote Control Lock

/Key Lock Mode

13. Balance

00 ~ 64

Transmission / Receiving Protocol

Transmission

OK Acknowledgement

[Command2][ ][Set ID][ ][OK][Data][x]

[Command1][Command2][ ][Set ID][ ][Data][Cr]

[Command 1] : First command to control the set.(j,k,m or x)

[Command 2] : Second command to control the set.

The set transmits ACK (acknowledgement) based on this for-

mat when receiving normal data. At this time, if the data is

data read mode, it indicates present status data. If the data is

data write mode, it returns the data of the PC computer.

[Set ID] : You can adjust the set ID to choose desired Set ID

number in Setup menu. Adjustment range is 1~ 99.

When selecting Set ID ‘0’, every connected set is

(

)

controlled. Set ID is indicated as decimal 1~ 99

Error Acknowledgement

(

)

on menu and as Hexa decimal 0x0~ 0x63 on

[Command2][ ][Set ID][ ][NG][Data][x]

transmission/receiving protocol.

Set transmits ACK(acknowledgement) based on this format

when receiving abnormal data form non-viable functions or

communication errors.

[DATA] : To transmit command data.

Transmit ‘FF’ data to read status of comand.

[Cr] : Carriage Return

[Command 2] : use as command.

ASCII code ‘0x0D’

[Set ID]: use the small character, if set ID is 10, set will send the ‘0’, ‘a’

[Data]: use the small character, if data is 0xab, set will send the ‘a’, ‘b’.

[NG]: use the large character.

[

] : ASCII code ‘space (0x20)’

APPENDIX

05. Volume Control (Command: k f)

To adjust volume.

01. Power (Command: k a)

To control Power On/Off of the TV.

You can also adjust volume with the volume buttons

on remote control.

Transmission [k][a][ ][Set ID][ ][Data][Cr]

Data 00 : Power Off

Data 01 : Power On

Transmission [k][f][ ][Set ID][ ][Data][Cr]

Data Min : 00 ~ Max : 64

Acknowledgement [a][ ][Set ID][ ][OK/NG][Data][x]

To show Power On/Off.

Refer to ‘Real data mapping 1 ’. See page 68.

Transmission [k][a][ ][Set ID][ ][FF][Cr]

Acknowledgement [f][ ][Set ID][ ][OK/NG][Data][x]

Acknowledgement [a][ ][Set ID][ ][OK/NG][Data][x]

* If there is the time delay between command and

ack message during power on sequence, It should

be described like “Note: In this model, set will send

the Acknowledge after power on processing com-

pletion. There might be a time delay between com-

mand and acknowledge.”

06. Contrast (Command: k g)

To adjust screen contrast.

You can also adjust contrast in the Picture menu.

Transmission [k][g][ ][Set ID][ ][Data][Cr]

Data Min : 00 ~ Max : 64

02. Aspect Ratio (Command: k c) (Main picture size)

To adjust the screen format. (Main picture format)

Refer to ‘Real data mapping 1 ’. See page 68.

Acknowledgement [g][ ][Set ID][ ][OK][Data][x]

You can adjust the screen format using the Aspect

Ratio in the Picture menu.

Transmission [k][c][ ][Set ID][ ][Data][Cr]

07. Brightness (Command: k h)

Data 01: Normal screen (4:3)

Data 02: Wide screen (16:9)

Data 06: Original

Data 07: 14:9

To adjust screen brightness.

You can also adjust brightness in the Picture menu.

Data 04: Zoom1

Data 05: Zoom2

Data 09: Just Scan

Transmission [k][h][ ][Set ID][ ][Data][Cr]

Data Min : 00 ~ Max : 64

Acknowledgement [c][ ][Set ID][ ][OK/NG][Data][x]

Refer to ‘Real data mapping 1 ’. See page 68.

* Using the RGB-PC, Component or HDMI input, you

select either 16:9 or 4:3 screen aspect ratio.

* Just Scan works in the following mode:

Component (720p/1080i/1080p),

HDMI (720p/1080i/1080p)

Acknowledgement [h][ ][Set ID][ ][OK/NG][Data][x]

08. Colour (Command: k i)

03. Screen Mute (Command: k d)

To select screen mute on/off.

To adjust the screen colour.

You can also adjust colour in the Picture menu.

Transmission [k][d][ ][Set ID][ ][Data][Cr]

Data 00 : Screen mute off (Picture on)

Data 01 : Screen mute on (Picture off)

Transmission [k][i][ ][Set ID][ ][Data][Cr]

Data Min : 00 ~ Max : 64

Refer to ‘Real data mapping 1 ’. See page 68.

Acknowledgement [d][ ][Set ID][ ][OK/NG][Data][x]

Acknowledgement [i][ ][Set ID][ ][OK/NG][Data][x]

09. Tint (Command: k j)

04. Volume Mute (Command: k e)

To control volume mute on/off.

To adjust the screen tint.

You can also adjust tint in the Picture menu.

You can also adjust mute using the MUTE button on

remote control.

Transmission [k][j][ ][Set ID][ ][Data][Cr]

Data Min : 00 ~ Max : 64

Transmission [k][e][ ][Set ID][ ][Data][Cr]

Data 00 : Volume mute on (Volume off)

Data 01 : Volume mute off (Volume on)

Refer to ‘Real data mapping 1 ’. See page 68.

Acknowledgement [j][ ][Set ID][ ][OK/NG][Data][x]

Acknowledgement [e][ ][Set ID][ ][OK/NG][Data][x]

APPENDIX

15. Red Adjustment (Command: k v)

To adjust red in colour temperature.

10. Sharpness (Command: k k)

To adjust the screen sharpness.

Transmission [k][v][ ][Set ID][ ][Data][Cr]

You can also adjust sharpness in the Picture menu.

Transmission [k][k][ ][Set ID][ ][Data][Cr]

Data Min : 00 ~ Max : 64

Data Min: 00 ~ Max: 3C

Refer to ‘Real data mapping 2’. See page 68.

Refer to ‘Real data mapping 1 ’. See page 68.

Acknowledgement [v][ ][Set ID][ ][OK/NG][Data][x]

Acknowledgement [k][ ][Set ID][ ][OK/NG][Data][x]

16. Green Adjustment (Command: k w)

To adjust green in colour temperature.

11. OSD Select (Command: k l)

To select OSD (On Screen Display) on/off when

controlling remotely.

Transmission [k][w][ ][Set ID][ ][Data][Cr]

Data Min: 00 ~ Max: 3C

Transmission [k][l][ ][Set ID][ ][Data][Cr]

Data 00: OSD off

Refer to ‘Real data mapping 2’. See page 68.

Data 01: OSD on

Acknowledgement [w][ ][Set ID][ ][OK/NG][Data][x]

Acknowledgement [l][ ][Set ID][ ][OK][Data][x]

17. Blue Adjustment (Command: k $)

To adjust blue in colour temperature.

12. Remote Control Lock/Key Lock Mode (Command: k m)

To lock the remote control and the side key

controls on the set.

Transmission [k][$][ ][Set ID][ ][Data][Cr]

Data Min: 00 ~ Max: 3C

Transmission [k][m][ ][Set ID][ ][Data][Cr]

Data 00: Lock off

Data 01: Lock on

Refer to ‘Real data mapping 2’. See page 68.

Acknowledgement [$][ ][Set ID][ ][OK/NG][Data][x]

Acknowledgement [m][ ][Set ID][ ][OK/NG][Data][x]

18. Abnormal State (Command: k z)

To recognize an abnormal state.

13. Balance (Command: k t)

To adjust balance.

You can also adjust balance in the Audio menu.

Transmission [k][z][ ][Set ID][ ][FF][ ][Cr]

Transmission [k][t][ ][Set ID][ ][Data][Cr]

Data Min : 00 ~ Max : 64

Data FF: Read

Acknowledgement [z][ ][Set ID][ ][OK/NG][Data][x]

Refer to ‘Real data mapping 1 ’. See page 68.

Data 00: Normal (Power on and signal exist)

Data 01: No signal (Power on)

Acknowledgement [t][ ][Set ID][ ][OK/NG][Data][x]

Data 02: Turn the set off by remote control

Data 03: Turn the set off by sleep time function

Data 04: Turn the set off by RS-232C function

14. Colour Temperature (Command: k u)

To adjust colour temperature.

* This function is “read only”

You can also adjust Colour Temperature in the Picture

menu.

Transmission [k][u][ ][Set ID][ ][Data][Cr]

Data 00: Medium 01: Cool 02: Warm(Don’t operate in RGB, DVI mode)

Data 05: 9300K 06: 6500K 07: sRGB(Operate in RGB, DVI mode)

Acknowledgement [u][ ][Set ID][ ][OK/NG][Data][x]

APPENDIX

22. Channel Skip(Command: m b)

19 . Auto Configure (Command: j u)

To adjust picture position and minimize image

G To set skip status for the current Programme.

shaking automatically. It works only in RGB (PC)

mode.

Transmission [m][b][ ][Set ID][ ][Data][Cr]

Data 00 : Skip

01 : Add

Transmission [j][u][ ][Set ID][ ][Data][Cr]

Acknowledgement [b][ ][Set ID][ ][OK/NG][Data][x]

Data 01: To set

Acknowledgement [u][ ][Set ID][ ][OK/NG][Data][x]

23. Key Code (Command: m c)

To send IR remote key code.

20. Equalize(Command: j v)

G To adjust equalize.

Transmission [m][c][ ][Set ID][ ][Data][Cr]

Transmission [j][v][ ][Set ID][ ][Data][Cr]

Data: Key code - Refer to page 62.

MSB

LSB

Acknowledgement [c][ ][Set ID][ ][OK/NG][Data][x]

Data

Frequency

24. Input select (Command: x b)

Frequency

Data

(Main Picture Input)

Remark

Step

4 Hex

To select input source for set

Transmission [x][b][ ][Set ID][ ][Data][Cr]

1’st Band

2’nd Band

3’rd Band

4’th Band

Data: Structure

...

MSB

LSB

5’th Band

External Input

Input Number

command

Input

Acknowledgement [v][ ][Set ID][ ][OK/NG][Data][x]

[x][b][ ][Set ID][ ][10][Cr]

[x][b][ ][Set ID][ ][20][Cr]

21 . Tune Command / Channel Tuning (Command: m a)

Tune Channel to following Physical number.

Component [x][b][ ][Set ID][ ][40][Cr]

RGB-PC

DVI

[x][b][ ][Set ID][ ][60][Cr]

[x][b][ ][Set ID][ ][80][Cr]

[x][b][ ][Set ID][ ][90][Cr]

[x][b][ ][Set ID][ ][91][Cr]

Transmission [m][a][ ][Set ID][ ][Data0][ ][Data1]

HDMI1

HDMI2

[ ][Data2][Cr]

Data00 Min: 00 ~ Max: 63 (Max : C8 in China area)

(*transmit by Hexadecimal code)

Data01 don’t care

Acknowledgement [b][ ][Set ID][ ][OK/NG][Data][x]

Data02 0 ; Main

Real data mapping 1

00 : Step 0

Real data mapping 2

00 : -30

1 : Sub

Acknowledgement [a][ ][Set ID][OK][ ][Data0][Data1][x]

[a][ ][Set ID][NG][ ][Data0][x]

32 : Step 50

64 : Step 100

1E : 0

3C : +30

Lucent Technologies Telephone Call Handling Back Panels_ Front Panels and 4424LD+ Telephone User Manual
Magnavox COLOR TV 25 INCH User Manual
Memorex MT1190C User Manual
Miele KM 406 User Manual
Moffat E85 A 8 HLD User Manual
NEC MultiSync MD213MC User Manual
Panasonic WJ HD316 User Manual
Philips 21GR1250 User Manual
Philips 100Hz TV User Manual
Philips SE4502B User Manual