LG Electronics LG Life Good Computer Monitor L1733TR User Manual

Internal Use Only

Website:http://biz.LGservice.com

COLOR MONITOR

SERVICE MANUAL

CHASSIS NO. : LM57B

MODEL:

L1733TR (L1733TR-SFQ.A**MQP)

L1933TR (L1933TR-SFQ.A**MQP,A**RQP)

(

) **Same model for Service

CAUTION

BEFORE SERVICING THE UNIT,

READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

*To apply the MSTAR Chip.

CONTENTS

SPECIFICATIONS ................................................... 2

SERVICE OSD........................................................17

TROUBLESHOOTING GUIDE .............................. 18

WIRING DIAGRAM ............................................... 24

EXPLODED VIEW...................................................25

REPLACEMENT PARTS LIST ...............................27

SCHEMATIC DIAGRAM......................................... 31

PRECAUTIONS ....................................................... 3

TIMING CHART ....................................................... 7

DISASSEMBLY ....................................................... 8

BLOCK DIAGRAM...................................................12

DISCRIPTION OF BLOCK DIAGRAM .................. 14

ADJUSTMENT ...................................................... 16

SPECIFICATIONS

1. LCD CHARACTERISTICS

4. Max. Resolution

D-sub Analog

Digital

Type

: TFT Color LCD Module

: 1280 x 1024@75Hz

: 1280 x 1024@60Hz

Active Display Area : 17 inch - L1733T

: 19 inch - L1933T

Pixel Pitch

: 0.264 (H) x 0.264 (V) - L1733T

5. POWER SUPPLY

5-1. Power : AC 100~240V, 50/60Hz , 0.6A

: 0.294 (H) x 0.294 (V) - L1933T

: 8bits, 16.2M colors

Color Depth

Size

358.5 (H) x 296.5 (V) x 17.0(D) - L1733T

5-2. Power Consumption

396 (H) x 324 (V) x 17.5(D) - L1933T

MODE

VIDEO POWER CONSUMPTION LED COLOR

H/V SYNC

ON/ON

Electrical Interface

Surface Treatment

Operating Mode

Backlight Unit

: LVDS

: Hard-coating(3H), Anti-Glare

less than 33 W -L1733T

less than 37 W -L1933T

less than 1 W

BLUE

or GREEN

AMBER

OFF

POWER ON (NORMAL)

ACTIVE

Normally White, Transmissive mode

: 4-CCFL

STAND-BY

SUSPEND

OFF

OFF/ON

ON/OFF

2. OPTICAL CHARACTERISTICS

2-1. Viewing Angle by Contrast Ratio ≥ 10

DPMS OFF

OFF/OFF

Left : -60° min., -70°(Typ) Right : +60° min., +70°(Typ)

Top :+60° min., +75°(Typ) Bottom : -50° min., -65°(Typ)

POWER S/W Off

2-2. Luminance

230(min), 300(Typ) (Full White pattern, 0.70V) -6500K

150(min) (Full White pattern, 0.70V) -9300K

75%(min)

6. ENVIRONMENT

6-1. Operating Temperature : 10°C~35°C (50°F~95°F)

(Ambient)

6-2. Relative Humidity

6-3. MTBF

: 10%~80% (Non-condensing)

: 50,000 HRS with 90% Confidence

: 50,000 Hours(Min)

2-3. Contrast Ratio

: 1400:1 (DFC)

Lamp Life

3. SIGNAL (Refer to the Timing Chart)

3-1. Sync Signal

7. DIMENSIONS (with TILT/SWIVEL)

L1733T

• Type

: Separate Sync, Digital, SOG

Width

Depth

Height

: 364.5 mm (14.35'')

: 180 mm (7.09'')

: 378.2 mm (14.89'')

3-2. Video Input Signal

1) Type

: R, G, B Analog

: 0~0.71 V

: 0 Vp-p

: 0.467Vp-p

: 0.714Vp-p

2) Voltage Level

a) Color 0, 0

b) Color 7, 0

c) Color 15, 0

3) Input Impedance : 75Ω

L1933T

Width

Depth

Height

: 402 mm (15.83'')

: 180 mm (7.09'')

: 407.5 mm (16.04'')

3-3. Operating Frequency

8. WEIGHT (with TILT/SWIVEL)

L1733T

Horizontal

Vertical

: 30 ~ 83kHz

: 56 ~ 75Hz

Net. Weight

: 3.5 kg (7.72 lbs)

Gross Weight

: 4.6 kg (10.14 lbs)

L1933T

Net. Weight

Gross Weight

: 4.4 kg (9.70 lbs)

: 5.6 kg (12.35 lbs)

LGE Internal Use Only

Only for training and service purposes

- 2 -

PRECAUTION

WARNING FOR THE SAFETY-RELATED COMPONENT.

WARNING

BE CAREFUL ELECTRIC SHOCK !

• There are some special components used in LCD

monitor that are important for safety. These parts are

marked on the schematic diagram and the

replacement parts list. It is essential that these critical

parts should be replaced with the manufacturer’s

specified parts to prevent electric shock, fire or other

hazard.

• If you want to replace with the new backlight (CCFL) or

inverter circuit, must disconnect the AC adapter

because high voltage appears at inverter circuit about

650Vrms.

• Handle with care wires or connectors of the inverter

circuit. If the wires are pressed cause short and may

burn or take fire.

• Do not modify original design without obtaining written

permission from manufacturer or you will void the

original parts and labor guarantee.

Leakage Current Hot Check Circuit

TAKE CARE DURING HANDLING THE LCD MODULE

WITH BACKLIGHT UNIT.

AC Volt-meter

• Must mount the module using mounting holes arranged

in four corners.

• Do not press on the panel, edge of the frame strongly

or electric shock as this will result in damage to the

screen.

Good Earth Ground

such as WATER PIPE,

CONDUIT etc.

To Instrument’s

• Do not scratch or press on the panel with any sharp

objects, such as pencil or pen as this may result in

damage to the panel.

exposed

METALLIC PARTS

1.5 Kohm/10W

• Protect the module from the ESD as it may damage the

electronic circuit (C-MOS).

• Make certain that treatment person’s body are

grounded through wrist band.

• Do not leave the module in high temperature and in

areas of high humidity for a long time.

• The module not be exposed to the direct sunlight.

• Avoid contact with water as it may a short circuit within

the module.

• If the surface of panel become dirty, please wipe it off

with a softmaterial. (Cleaning with a dirty or rough cloth

may damage the panel.)

CAUTION

Please use only a plastic screwdriver to protect yourself

from shock hazard during service operation.

LGE Internal Use Only

Only for training and service purposes

- 3 -

SERVICING PRECAUTIONS

CAUTION: Before servicing receivers covered by this

9. Use with this receiver only the test fixtures specified in

service manual and its supplements and addenda, read

and follow the SAFETY PRECAUTIONS on page 3 of this

publication.

this service manual.

CAUTION: Do not connect the test fixture ground strap

to any heat sink in this receiver.

NOTE: If unforeseen circumstances create conflict

between the following servicing precautions and any of the

safety precautions on page 3 of this publication, always

follow the safety precautions. Remember: Safety First.

Electrostatically Sensitive (ES) Devices

Some semiconductor (solid-state) devices can be

damaged easily by static electricity. Such components

commonly are called Electrostatically Sensitive (ES)

Devices. Examples of typical ES devices are integrated

circuits and some field-effect transistors and

semiconductor "chip" components. The following

techniques should be used to help reduce the incidence of

component damage caused by static by static electricity.

1. Immediately before handling any semiconductor

component or semiconductor-equipped assembly, drain

off any electrostatic charge on your body by touching a

known earth ground. Alternatively, obtain and wear a

commercially available discharging wrist strap device,

which should be removed to prevent potential shock

reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with

ES devices, place the assembly on a conductive

surface such as aluminum foil, to prevent electrostatic

charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or

unsolder ES devices.

4. Use only an anti-static type solder removal device.

Some solder removal devices not classified as "anti-

static" can generate electrical charges sufficient to

damage ES devices.

5. Do not use freon-propelled chemicals. These can

generate electrical charges sufficient to damage ES

devices.

6. Do not remove a replacement ES device from its

protective package until immediately before you are

ready to install it. (Most replacement ES devices are

packaged with leads electrically shorted together by

conductive foam, aluminum foil or comparable

conductive material).

General Servicing Precautions

1. Always unplug the receiver AC power cord from the AC

power source before;

a. Removing or reinstalling any component, circuit

board module or any other receiver assembly.

b. Disconnecting or reconnecting any receiver electrical

plug or other electrical connection.

c. Connecting a test substitute in parallel with an

electrolytic capacitor in the receiver.

CAUTION: A wrong part substitution or incorrect

polarity installation of electrolytic capacitors may

result in an explosion hazard.

d. Discharging the picture tube anode.

2. Test high voltage only by measuring it with an

appropriate high voltage meter or other voltage

measuring device (DVM, FETVOM, etc) equipped with

a suitable high voltage probe.

Do not test high voltage by "drawing an arc".

3. Discharge the picture tube anode only by (a) first

connecting one end of an insulated clip lead to the

degaussing or kine aquadag grounding system shield

at the point where the picture tube socket ground lead

is connected, and then (b) touch the other end of the

insulated clip lead to the picture tube anode button,

using an insulating handle to avoid personal contact

with high voltage.

4. Do not spray chemicals on or near this receiver or any

of its assemblies.

5. Unless specified otherwise in this service manual,

clean electrical contacts only by applying the following

mixture to the contacts with a pipe cleaner, cotton-

tipped stick or comparable non-abrasive applicator;

10% (by volume) Acetone and 90% (by volume)

isopropyl alcohol (90%-99% strength)

7. Immediately before removing the protective material

from the leads of a replacement ES device, touch the

protective material to the chassis or circuit assembly

into which the device will be installed.

CAUTION: This is a flammable mixture.

Unless specified otherwise in this service manual,

lubrication of contacts in not required.

CAUTION: Be sure no power is applied to the chassis

or circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged

replacement ES devices. (Otherwise harmless motion

such as the brushing together of your clothes fabric or

the lifting of your foot from a carpeted floor can

generate static electricity sufficient to damage an ES

device.)

6. Do not defeat any plug/socket B+ voltage interlocks

with which receivers covered by this service manual

might be equipped.

7. Do not apply AC power to this instrument and/or any of

its electrical assemblies unless all solid-state device

heat sinks are correctly installed.

8. Always connect the test receiver ground lead to the

receiver chassis ground before connecting the test

receiver positive lead.

Always remove the test receiver ground lead last.

LGE Internal Use Only

Only for training and service purposes

- 4 -

General Soldering Guidelines

Replacement

1. Use a grounded-tip, low-wattage soldering iron and

1. Carefully insert the replacement IC in the circuit board.

2. Carefully bend each IC lead against the circuit foil pad

and solder it.

3. Clean the soldered areas with a small wire-bristle

brush. (It is not necessary to reapply acrylic coating to

the areas).

appropriate tip size and shape that will maintain tip

temperature within the range or 500 F to 600 F.

2. Use an appropriate gauge of RMA resin-core solder

composed of 60 parts tin/40 parts lead.

3. Keep the soldering iron tip clean and well tinned.

4. Thoroughly clean the surfaces to be soldered. Use a

mall wire-bristle (0.5 inch, or 1.25cm) brush with a

metal handle.

Do not use freon-propelled spray-on cleaners.

5. Use the following unsoldering technique

a. Allow the soldering iron tip to reach normal

temperature.

"Small-Signal" Discrete Transistor

Removal/Replacement

1. Remove the defective transistor by clipping its leads as

close as possible to the component body.

2. Bend into a "U" shape the end of each of three leads

remaining on the circuit board.

3. Bend into a "U" shape the replacement transistor leads.

4. Connect the replacement transistor leads to the

corresponding leads extending from the circuit board

and crimp the "U" with long nose pliers to insure metal

to metal contact then solder each connection.

(500 F to 600 F)

b. Heat the component lead until the solder melts.

c. Quickly draw the melted solder with an anti-static,

suction-type solder removal device or with solder

braid.

CAUTION: Work quickly to avoid overheating the

circuitboard printed foil.

6. Use the following soldering technique.

a. Allow the soldering iron tip to reach a normal

Power Output, Transistor Device

Removal/Replacement

1. Heat and remove all solder from around the transistor

leads.

temperature (500 F to 600 F)

b. First, hold the soldering iron tip and solder the strand

2. Remove the heat sink mounting screw (if so equipped).

3. Carefully remove the transistor from the heat sink of the

circuit board.

against the component lead until the solder melts.

4. Insert new transistor in the circuit board.

5. Solder each transistor lead, and clip off excess lead.

6. Replace heat sink.

c. Quickly move the soldering iron tip to the junction of

the component lead and the printed circuit foil, and

hold it there only until the solder flows onto and

around both the component lead and the foil.

CAUTION: Work quickly to avoid overheating the

circuit board printed foil.

d. Closely inspect the solder area and remove any

excess or splashed solder with a small wire-bristle

brush.

Diode Removal/Replacement

1. Remove defective diode by clipping its leads as close

as possible to diode body.

2. Bend the two remaining leads perpendicular y to the

circuit board.

3. Observing diode polarity, wrap each lead of the new

diode around the corresponding lead on the circuit

board.

4. Securely crimp each connection and solder it.

5. Inspect (on the circuit board copper side) the solder

joints of the two "original" leads. If they are not shiny,

reheat them and if necessary, apply additional solder.

IC Remove/Replacement

Some chassis circuit boards have slotted holes (oblong)

through which the IC leads are inserted and then bent flat

against the circuit foil. When holes are the slotted type,

the following technique should be used to remove and

replace the IC. When working with boards using the

familiar round hole, use the standard technique as

outlined in paragraphs 5 and 6 above.

Fuse and Conventional Resistor

Removal/Replacement

1. Clip each fuse or resistor lead at top of the circuit board

Removal

hollow stake.

1. Desolder and straighten each IC lead in one operation

by gently prying up on the lead with the soldering iron

tip as the solder melts.

2. Draw away the melted solder with an anti-static

suction-type solder removal device (or with solder

braid) before removing the IC.

2. Securely crimp the leads of replacement component

around notch at stake top.

3. Solder the connections.

CAUTION: Maintain original spacing between the

replaced component and adjacent components and the

circuit board to prevent excessive component

temperatures.

LGE Internal Use Only

Only for training and service purposes

- 5 -

Circuit Board Foil Repair

At Other Connections

Excessive heat applied to the copper foil of any printed

circuit board will weaken the adhesive that bonds the foil

to the circuit board causing the foil to separate from or

"lift-off" the board. The following guidelines and

procedures should be followed whenever this condition is

encountered.

Use the following technique to repair the defective copper

pattern at connections other than IC Pins. This technique

involves the installation of a jumper wire on the

component side of the circuit board.

1. Remove the defective copper pattern with a sharp

knife.

Remove at least 1/4 inch of copper, to ensure that a

hazardous condition will not exist if the jumper wire

opens.

At IC Connections

To repair a defective copper pattern at IC connections use

the following procedure to install a jumper wire on the

copper pattern side of the circuit board. (Use this

technique only on IC connections).

2. Trace along the copper pattern from both sides of the

pattern break and locate the nearest component that is

directly connected to the affected copper pattern.

3. Connect insulated 20-gauge jumper wire from the lead

of the nearest component on one side of the pattern

break to the lead of the nearest component on the

other side.

1. Carefully remove the damaged copper pattern with a

sharp knife. (Remove only as much copper as

absolutely necessary).

2. carefully scratch away the solder resist and acrylic

coating (if used) from the end of the remaining copper

pattern.

3. Bend a small "U" in one end of a small gauge jumper

wire and carefully crimp it around the IC pin. Solder the

IC connection.

Carefully crimp and solder the connections.

CAUTION: Be sure the insulated jumper wire is

dressed so the it does not touch components or sharp

edges.

4. Route the jumper wire along the path of the out-away

copper pattern and let it overlap the previously scraped

end of the good copper pattern. Solder the overlapped

area and clip off any excess jumper wire.

LGE Internal Use Only

Only for training and service purposes

- 6 -

TIMING CHART

VIDEO

SYNC

Total

Period

( E )

800

449

Video

Active

Sync

Duration

( D )

Front

Porch

( C )

Blanking

Time

Sync

Dot

H / V

Frequency

MODE

Resolution

640 x 350

Polarity

Clock

Time ( A )

( B )

H(Pixels)

V(Lines)

H(Pixels)

V(Lines)

H(Pixels)

V(Lines)

H(Pixels)

V(Lines)

H(Pixels)

V(Lines)

H(Pixels)

V(Lines)

H(Pixels)

V(Lines)

H(Pixels)

V(Lines)

H(Pixels)

V(Lines)

H(Pixels)

V(Lines)

H(Pixels)

V(Lines)

H(Pixels)

V(Lines)

H(Pixels)

V(Lines)

25.175

31.469

70.09

31.468

70.08

31.469

59.94

37.5

640

350

28.321

25.175

31.5

900

720

108

720 X 400

640 x 480

800 x 600

832 x 624

1024 x 768

1152 x 870

1152 x 900

1280 x 1024

449

400

800

640

525

480

840

640

120

500

480

+/-

40.0

37.879

60.317

46.875

75.0

1056

628

800

128

600

49.5

1056

625

800

160

600

57.283

65.0

49.725

74.55

48.363

60.0

1152

667

832

224

624

1344

806

1024

768

136

160

78.75

100.0

92.978

108.0

135.0

60.123

75.029

68.681

75.062

61.805

65.96

63.981

60.02

79.976

75.035

1312

800

1024

768

176

+/-

1456

915

1152

870

128

144

1504

937

1152

900

134

200

1688

1066

1688

1066

1280

1024

1280

1024

112

248

144

248

LGE Internal Use Only

Only for training and service purposes

- 7 -

DISASSEMBLY-Set

# 1

# 2

Soft pad on the table.

Monitor on the pad.

# 3

# 4-1

Hold the head & stand base and then

Pull up the stand part.

Twist Stand until "Click".

# 5

# 4-2

Separate head & stand

LGE Internal Use Only

Only for training and service purposes

- 8 -

# 6

# 7

1. Pull the front cover upward.

2. Then, let the all latches are separated.(#3-1~3-2)

3. Put the front face down.

Remove the screws.

# 9

# 8

Disassemble back cover.

LGE Internal Use Only

Only for training and service purposes

- 9 -

DISASSEMBLY-Stand

* In case of Latch 4.

# 1-1

# 1-2

Push the four latches on the bottom to the

outside and Separate Stand Body & Base.

(Reference the #1-2)

# 2

# 3

After finished repair, necessarily push 4ea

Latches to inside for restoration.

LGE Internal Use Only

Only for training and service purposes

- 10 -

DISASSEMBLY-Stand

* In case of Latch 2.

# 1

# 2

Hold the stand body.

Confirm two latch of right and left.

# 3

# 4

Push the latch to the inside.

Push the base to the opposite direction.

# 5

Confirm the condition of separation.

LGE Internal Use Only

Only for training and service purposes

- 11 -

BLOCK DIAGRAM

M o d u l e

K E Y

1 2 V

D - S u b

V D I - D

LGE Internal Use Only

Only for training and service purposes

- 12 -

BLOCK DIAGRAM-POWER

LGE Internal Use Only

Only for training and service purposes

- 13 -

DESCRIPTION OF BLOCK DIAGRAM

1. Video Controller Part.

This part amplifies the level of video signal for the digital conversion and converts from the analog video signal to the

digital video signal using a pixel clock.

The pixel clock for each mode is generated by the PLL.

The range of the pixel clock is from 25MHz to 135MHz.

This part consists of the Scaler, ADC convertor, TMDS receiver and LVDS transmitter.

The Scaler gets the video signal converted analog to digital, interpolates input to 1280 X 1024 resolution signal and

outputs 8-bit R, G, B signal to transmitter.

2. Power Part.

This part consists of the one 3.3V, and one 1.8V regulators to convert power which is provided 5V in Power board.

12V is provided for inverter, 5V is provided for LCD panel.

Also, 5V is converted 3.3V and 1.8V by regulator. Converted power is provided for IC in the main board.

The inverter converts from DC12V to AC 700Vrms and operates back-light lamps of module.

3. MICOM Part.

This part is include video controller part. And this part consists of EEPROM IC which stores control data, Reset IC and

the Micom.

The Micom distinguishes polarity and frequency of the H/V sync are supplied from signal cable.

The controlled data of each modes is stored in EEPROM.

LGE Internal Use Only

Only for training and service purposes

- 14 -

LIPS Board Block Diagram

12V

50 ~ 60Hz

100KHz

HVDC

SWITCHING

TRANSFORMER

EMI

COMPONENTS

INPUT RECTIFIER

AND FILTER

OUTPUT RECTIFIER

AND FILTER

LINE

GND

100 ~ 240V

SIGNAL

COLLENT-

ION

PWM CONTROL

CIRCUIT

PHOTO-COUPLER

ISOLATION

PRIMARY

SECONDARY

12V

High Voltage

INVERTER CIRCUIT

Operation description_LIPS

1. EMI components.

This part contains of EMI components to comply with global marketing EMI standards like FCC,VCCI CISPR, the

circuit included a line-filter, across line capacitor and of course the primary protection fuse.

2. Input rectifier and filter.

This part function is for transfer the input AC voltage to a DC voltage through a bridge rectifier and a bulk capacitor.

3. Energy Transfer.

This part function is for transfer the primary energy to secondary through a power transformer.

4. Output rectifier and filter.

This part function is to make a pulse width modulation control and to provide the driver signal to power switch, to

adjust the duty cycle during different AC input and output loading condition to achieve the dc output stabilized, and

also the over power protection is also monitor by this part.

5. Photo-Coupler isolation.

This part function is to feed back the DC output changing status through a photo transistor to primary controller to

achieve the stabilized DC output voltage.

6. Signal collection.

This part function is to collect the any change from the DC output and feed back to the primary through photo

transistor.

LGE Internal Use Only

Only for training and service purposes

- 15 -

ADJUSTMENT

Windows EDID V1.0 User Manual

2. EDID Read & Write

1) Run WinEDID.exe

Operating System: MS Windows 98, 2000, XP

Port Setup: Windows 98 => Don’t need setup

Windows 2000, XP => Need to Port Setup.

This program is available to LCD Monitor only.

1. Port Setup

a) Copy “UserPort.sys” file to

“c:\WINNT\system32\drivers” folder

b) Run Userport.exe

2) Edit Week of Manufacture, Year of Manufacture,

Serial Number

a) Input User Info Data

b) Click “Update” button

c) Click “ Write” button

c) Remove all default number

d) Add 300-3FF

e) Click Start button.

f) Click Exit button.

LGE Internal Use Only

Only for training and service purposes

- 16 -

SERVICE OSD

1) Turn off the power switch at the front side of the display.

2) Wait for about 5 seconds and press MENU, POWER switch with 1 second interval.

3) The SVC OSD menu contains additional menus that the User OSD menu as described below.

a) Auto Color : W/B balance and Automatically sets the gain and offset value.

b) NVRAM INIT : EEPROM initialize.(24C08)

c) CLEAR ETI : To initialize using time.

d) AGING : Select Aging mode(on/off).

e) R/G/B-9300K : Allows you to set the R/G/B-9300K value manually.

f) R/G/B-6500K : Allows you to set the R/G/B-6500K value manually.

g) R/G/B-Offset : Allows you to set the R/G/B-Offset value manually.(Analog Only)

h) R/G/B-Gain : Allows you to set the R/G/B-Gain value manually.(Analog Only)

i) MODULE : To select applied module.

IBM

Compatible PC

Video Signal

Generator

PARALLEL PORT

OFF

Power inlet (required)

4.7K

Power Select Switch

(110V/220V)

Power LED

74LS06

4.7K

OFF

74LS06

ST Switch

V-Sync On/Off Switch

(Switch must be ON.)

Figure 1. Cable Connection

LGE Internal Use Only

Only for training and service purposes

- 17 -

TROUBLESHOOTING GUIDE

1. NO POWER

NO POWER

(POWER INDICATOR OFF)

Check Power Board,

And Find Out a Short Point

as Opening

Check J403 Voltage

Pin5, Pin6 (5V)?

Each Power Line

YES

Check

U301 Pin2 Voltage

(3.3V) ?

Check 3.3V Line

(Open Check)

No Problem

YES

Check Key Control

Connector Routine

Is U201

Pin75 (3.3V)

Voltage ?

Check 3.3V Line

Check X-TAL

YES

Check U201 Pin 96

Pulse

YES

Check U201

Waveforms

U201-#96

LGE Internal Use Only

Only for training and service purposes

- 18 -

2. NO RASTER (OSD IS NOT DISPLAYED) – LIPS

NO RASTER

(OSD IS NOT DISPLAYED)

CHECK POWER BOARD,

AND FIND OUT A SHORT

POINT AS OPENING EACH

POWER LINE

J403

PIN5, PIN6

5V?

YES

CHECK MICOM INV

ON/OFF PORT.

J403 PIN9

5V?

YES

1. CONFIRM BRIGHTNESS

OSD CONTRL STATE.

2. CHECK MICOM DIM-ADJ

PORT

J403 PIN10

5V?

YES

CHECK

PULSE AS

CONTACTING SCOPE

PROBE TO CAUTION LABEL.

(CONTACT PROBE TO

CAUTION LABEL.

CAN YOU SEE PULSE

AT YOUR

LIPS

SCOPE?

YES

REPLACE CCFL LAMP

IN THE LCD MODULE

LGE Internal Use Only

Only for training and service purposes

- 19 -

3. NO RASTER (OSD IS NOT DISPLAYED) – MSTAR

NO RASTER

(OSD IS NOT DISPLAYED)

U201

PIN 16, 75

3.3V?

CHECK U301

YES

1. CHECK C210, C211

SOLDERING CONDITION

2. CHECK X201

U201

PIN96, 97

OSCILLATE AS

14.31MHZ?

3. TROUBLE IN U201

YES

U201

PIN27 IS 48KHz H-SYNC?

PIN28 IS 60Hz V-SYNC?

IS PULSE APPEARED

AT SIGNAL PINS?

CHECK CONNECTION

LINE FROM D-SUB TO

U201

AT MODE 12?

YES

TROUBLE IN CABLE

OR LCD MODULE

Waveforms

U201-#96, 97

U201-#27 H-SYNC

U201-#28 V-SYNC

LGE Internal Use Only

Only for training and service purposes

- 20 -

4. TROUBLE IN DPM

TROUBLE IN DPM

CHECK PC

PC IS NOT GOING

INTO DPM OFF MODE

CHECK

R442, R443

YES

CHECK

U201 PIN 27,28

SYNC PULSE ?

CHECK H/V SYNC LINE

YES

TROUBLE IN U201

Waveforms

R442 H-Sync

R443 V-Sync

LGE Internal Use Only

Only for training and service purposes

- 21 -

5. POWER

NO POWER

(POWER INDICATOR OFF)

CHECK

Fuse F101 OK?

Trouble in Fuse (F101)

YES

CHECK

C101 Voltage

(AC110V->160Vdc

(AC220V->304Vdc

Check BD101

YES

CHECK

U101 Pin6 Waveform

(Square wave

Check U101 Pin7 : 9~10V

Check D102

Come out?)

YES

Check Q101 Drain

Waveform

Trouble in Q101

YES

Check D201, D202

Voltage

Trouble in D201, D202

YES

CHECK 5V, 12V Line

LGE Internal Use Only

Only for training and service purposes

- 22 -

6. Raster

NO Raster

(Lamp Off)

CHECK

P201 Pin9

3.3V?

Check Scaler Output

(Main Board)

YES

Check U301 Pin3

5V?

Check Q301, Q302

YES

Check the waveform of U301

Pin11, 12, 19, 20

Check U301 Pin2 OVP,

Less than 1.8V

YES

Check the waveform of U301

Pin11, 12, 19, 20

Check U301 Pin10 CMP,

Less than 2.75V

If waveform is no problem

Check Q303~Q308

Or Trouble in U303, U304

Check U303, U304

Drain waveform

YES

CHECK T301, T302

LGE Internal Use Only

Only for training and service purposes

- 23 -

WIRING DIAGRAM

30P

6631900109A

11P

6631T20023J

6631900011H

6631T20010E-L1733TR

6631900125A-L1933TR

LGE Internal Use Only

Only for training and service purposes

- 24 -

EXPLODED VIEW

LGE Internal Use Only

Only for training and service purposes

- 25 -

EXPLODED VIEW PARTS LIST

* Note: Safety mark

Ref. No.

Part No.

Description

010

ABJ32220472

ABJ32229471

EAJ32188801

EAJ32189001

or EAJ35908201

or EAJ32188901

6304FHS014B

3809900177B

3809900178B

3809900178H

AAN32608906

35509K0245D

35509K0246D

3520900038A

49509K0266A

49509K0267F

EBR36881501

6709900027A

Cabinet Assembly, L1753 . 17" SILVER best buy for L1733TR

Cabinet Assembly, L1953 . 19" SILVER L1933TR FOR BEST BUY

020

030

LCD,Module-TFT, LM170E03-TLB3 DRIVER 17.0INCH 1280X1024 300CD COLOR 72% 5/4 800 VS 1 5MS, 160/160, 4LAMP, 2CH-LVDS LG PHILIPS LCD .

LCD,Module-TFT, LM190E08-TLB2 DRIVER 19.0INCH 1280X1024 300CD COLOR 72% 5/4 800:1 P7 FACTORY 5MS, 160/160, 2CH-LVDS, 4LAMP LG PHILIPS LCD .

LCD,Module-TFT, LM190E08-TLB6 DRIVER 17.0INCH 1280X1024 300CD COLOR 72% 4/3 800:1 P7, Lusem/Lusem D-IC, 5ms LG PHILIPS LCD

LCD,Module-TFT, LM190E08-TLB5 DRIVER 19INCH 1280X1024 300CD COLOR 72% 5/4 800 : 1 P4 FACTORY 5MS, 2CH-LVDS, 160/160, 4LAMP LG PHILIPS LCD .

LCD,Module-TFT, HSD190ME13-D10(700VS1) DRIVER 19INCH 1280X1024 300CD COLOR 72% 4/3 700:1 - HANNSTAR DISPLAY CORPORATION

Cover Assembly, L1752T NON BACK COVER ASSY MODULE-LPL+DUAL-L1733TR

Cover Assembly, L1952T NON BACK COVER ASSY MODULE-LPL+DUAL-L1933TR

Cover Assembly, L1952T NON BACK COVER ASSY MODULE-HSD-DUAL-L1933TR

Base Assembly, ASSY Lx53 LM57B Lx53 PATTERN TEXTURE(3043900041L)

Cover, MOLD ABS L1752 ABS L1752 NEW BODY-L1733TR

040

050

Cover, MOLD ABS L1952 ABS L1952 NEW BODY-L1933TR

060

070

Indicator, LED&PRE AMP LX52 PMMA NON LED LENS

Plate, SHIELD LX52 LAMP-L1733TR

Plate, PRESS SPTE-C 0.3 LAMP SPTE SHIELD for 19' LPL 5ms module-L1933TR

PCB Assembly,Sub, CONTROL T.T LM57A ND L1953TR/HR... KXXXXPN L1953TR/HR...

SMPS,AC/DC, AIVP 100VTO240V 40W 50TO60HZ UL/CSA/VDE/SEV/SEMKO/FIMKO/IMQ/OVE/BSI WORLD WIDE LIEN CHANG

080

090

or 68719PT298A PCB Assembly,Power, POWER T.T LM57A L1752S KNRDQPT -

100

EBU30504102

EBU30504105

35509K0247A

49509S0034B

49509K0262A

49509K0263A

4940900022B

49519K0137A

35509K0243A

35509K0242A

35509K0244A

64109UP002A

Main Total Assembly, L1752HQ-BFQ BRAND LM57B-L1733TR

Main Total Assembly, L1752HQ-BFQ BRAND LM57B-L1933TR

Cover, MOLD ABS AF-320T L1752TX ABS .

110

120

130

Plate, SHIELD LX52 REAR SHIELD-DUAL

Plate, SUPPORT L1752 BRACKET-L1733TR

Plate, SUPPORT L1952S BRACKET-L1933TR

Knob, MAIN 5KEY LX52 TACK KNOB ADD SOURCE PRINTING

Plate Assembly, ASSY STAND HINGE ASSY FOR LX52S/T

Cover, LX52 HINGE L

140

150

160

170

180

190

Cover, LX52 HINGE R

Cover, LX52 HINGE COVER BODY

Power Cord, DTII-3P-11+DTII-3P-04 HONGCHANG UL/CSA 1870MM PLUG BLACK

or 6410TUW008A Power Cord, UL_CSA,LP-31 & SVT 18X3C, LS-13_1.87M_BLK LP-31 LS-13 1.87M - 125V 10A SVT 3XAWG18 BLACK UL CSA N

LGE Internal Use Only

Only for training and service purposes

- 26 -

REPLACEMENT PARTS LIST

CAUTION: BEFORE REPLACING ANY OF THESE COMPONENTS,

READ CAREFULLY THE SAFETY PRECAUTIONS IN THIS MANUAL.

MAIN BOARD AND POWER BOARD PARTS ARE DIFFERENT.

* NOTE : S SAFETY Mark

AL ALTERNATIVE PARTS

DATE: 2007. 02. 06.

DESCRIPTION / SPECIFICATION

*S *AL LOC. NO.

MAIN BOARD

CAPACITORS

PART NO.

DESCRIPTION / SPECIFICATION

*S *AL LOC. NO.

PART NO.

C715

C716

C717

C718

C719

C720

C723

C724

C725

C901

C902

C903

C904

C905

C906

C907

C908

C909

C910

C911

C912

C913

C914

0CC680CK41A

0CK104CF56A

0CK105CD56A

0CC101CK41A

0CE107EF610

0CK103CK51A

0CC102CK41A

0CK105CD56A

0CE107EF610

0CK104CK56A

0CK102CK56A

0CE227EF610

C1608C0G1H680JT 68pF 5% 50V

0603B104K160CT 100nF 10% 16V

C1608X7R1A105KT 1uF 10% 10V

C1608C0G1H101JT 100pF 5% 50V

KMG16VB100M 100uF 20% 16V 12

0603B103K500CT 10nF 10% 50V

C1608C0G1H102JT 1nF 5% 50V C

C1608X7R1A105KT 1uF 10% 10V

KMG16VB100M 100uF 20% 16V 12

0603B104K500CT 100nF 10% 50V

0603B102K500CT 1nF 10% 50V X

KMG16VB220M 220uF 20% 16V 21

C501

C502

C503

C504

C505

C506

C507

C508

C509

C510

C511

C512

C513

C514

C515

C516

C517

C518

C519

C520

C521

C522

C523

C524

C525

C526

C527

C528

C529

C530

C531

C532

C533

C534

C535

C536

C537

C538

C701

C702

C703

C704

C705

C706

C707

C708

C709

C710

C711

C712

C713

C714

0CK104CF56A

0603B104K160CT 100nF 10% 16V

C1608X7R1E473KT 47nF 10% 25V

C1608C0G1H102JT 1nF 5% 50V C

C1608X7R1E473KT 47nF 10% 25V

C1608C0G1H270JT 27pF 5% 50V

0603B103K500CT 10nF 10% 50V

0603B104K160CT 100nF 10% 16V

0603B224K160CT 220nF 10% 16V

SHL5.0TP16VB10M 10uF 20% 16V

0603B104K160CT 100nF 10% 16V

C1608C0G1H101JT 100pF 5% 50V

C1608C0G1H680JT 68pF 5% 50V

0603B104K500CT 100nF 10% 50V

C1608C0G1H680JT 68pF 5% 50V

0603B104K160CT 100nF 10% 16V

C1608C0G1H680JT 68pF 5% 50V

0CK473CH56A

0CC102CK41A

0CK473CH56A

0CC270CK41A

0CK103CK51A

0CK104CF56A

0CK224CF56A

0CE106CF638

0CK104CF56A

0CC101CK41A

0CC680CK41A

0CK104CK56A

0CC680CK41A

0CK104CF56A

0CC680CK41A

DIODEs

D701

D702

D703

D704

D705

D706

D707

D708

D709

D710

D711

D712

D713

D714

D715

ZD701

ZD702

ZD703

ZD704

ZD705

ZD708

ZD709

ZD710

0DS226009AA

0DSON00138A

0DD184009AA

0DSON00138A

0DD184009AA

0DZ560009GB

KDS226 1.2V 85V 300MA 2A 4NS

MMBD301LT1G 600MV 30V - - 1.

KDS184 KDS184 TP KEC - 85V -

MMBD301LT1G 600MV 30V - - 1.

KDS184 KDS184 TP KEC - 85V -

BZT52C5V6S-(F) 5.6V 5.2TO6V

ICs

U501

U502

0IPRP00784A

EAN30510505

FE251MOH-LF(TSUMO56WHJ-LF) 3

L1952HQ-SFQ ARDRQP TSUMO G

LGE Internal Use Only

Only for training and service purposes

- 27 -

DATE: 2007. 02. 06.

DESCRIPTION / SPECIFICATION

DATE: 2007. 02. 06.

DESCRIPTION / SPECIFICATION

*S *AL LOC. NO.

PART NO.

*S *AL LOC. NO.

PART NO.

U503

U701

U702

U901

U902

0ISG240860B

0IMMR00203A

0IMMR00014A

0IPMGFA003G

0IPMGSG016A

0IPMG78403A

M24C08-WMN6TP 8KBIT 1KX8BIT-L1733TR

FM24C08 8KBIT 1KX8BIT 2.7VTO-L1933TR

M24C02-RMN6TP 2KBIT 256X8BIT

R714

R715

R716

R717

R718

R719

R720

R721

R722

R723

R724

R725

R726

R727

R728

R729

R730

R731

R732

R733

R735

R736

R737

R738

R739

R903

R904

R905

R907

R909

R910

0RJ1001D677

0RJ0000D677

0RJ0332D677

0RJ0752D677

0RJ0682D677

0RJ0332D677

0RJ0752D677

0RJ0000D677

0RJ4701D677

0RJ2200D677

0RJ1000D677

0RJ2001D677

0RJ4701D677

0RJ5600D677

0RJ2202D677

0RJ2702D677

0RX0331K668

0RJ0000D677

MCR03EZPJ102 1KOHM 5% 1/10W

MCR03EZPJ000 0OHM 5% 1/10W 1

MCR03EZPJ330 33OHM 5% 1/10W

MCR03EZPJ750 75OHM 5% 1/10W

MCR03EZPJ680 68OHM 5% 1/10W

MCR03EZPJ330 33OHM 5% 1/10W

MCR03EZPJ750 75OHM 5% 1/10W

MCR03EZPJ000 0OHM 5% 1/10W 1

MCR03EZPJ472 4.7KOHM 5% 1/10

MCR03EZPJ221 220OHM 5% 1/10W

MCR03EZPJ101 100OHM 5% 1/10W

MCR03EZPJ202 2KOHM 5% 1/10W

MCR03EZPJ472 4.7KOHM 5% 1/10

MCR03EZPJ561 560OHM 5% 1/10W

MCR03EZPJ223 22KOHM 5% 1/10W

MCR03EZPJ273 27KOHM 5% 1/10W

RSD02F4J3R30 3.3OHM 5% 2W 12

MCR03EZPJ000 0OHM 5% 1/10W 1

M24C02-RMN6TP 2KBIT 256X8BIT

FAN1117AS33X 4.8TO10.3V 3.3V

LD1086D2T18TR 3.4TO30V 1.8V-L1733TR

AZ1086S-1.8TRE1 3.2TO10V 1.8-L1933TR

FILTERs

L901

L902

L903

0LCML00003B

MLB-201209-0120P-N2 120OHM 2

TRANSISTOR

Q501

Q701

Q702

0TR390409AE

0TRKE80046A

0TR390609FA

0TR390609DC

0TR390609FA

0TR390609DC

KST3904 NPN 6V 60V 40V 200MA-L1733TR

2N3904S NPN 6V 60V 40V 200MA-L1933TR

KST3906-MTF PNP -5V -40V -40-L1733TR

2N3906S-RTK PNP -5V -40V -40-L1933TR

KST3906-MTF PNP -5V -40V -40-L1733TR

2N3906S-RTK PNP -5V -40V -40-L1933TR

RESISTORs

R501

R502

R503

R504

R505

R506

R507

R508

R509

R510

R511

R512

R513

R516

R517

R518

R519

R522

R523

R524

R525

R526

R527

R530

R701

R702

R703

R704

R705

R706

R707

R708

R709

R710

R711

R712

R713

0RJ1000D677

0RJ0562D677

0RJ1000D677

0RJ0562D677

0RJ4700D677

0RJ1000D677

0RJ0562D677

0RJ4701D677

0RJ4700D677

0RJ3900D677

0RJ1002D677

0RJ0000D677

0RJ1502D677

0RJ4701D677

0RJ1000D677

0RJ1002D677

0RJ4701D677

0RJ0332D677

0RJ1002D677

0RJ4701D677

0RJ0332D677

0RJ0102D677

0RJ0332D677

0RJ0000D677

0RJ0102D677

MCR03EZPJ101 100OHM 5% 1/10W

MCR03EZPJ560 56OHM 5% 1/10W

MCR03EZPJ101 100OHM 5% 1/10W

MCR03EZPJ560 56OHM 5% 1/10W

MCR03EZPJ471 470OHM 5% 1/10W

MCR03EZPJ101 100OHM 5% 1/10W

MCR03EZPJ560 56OHM 5% 1/10W

MCR03EZPJ472 4.7KOHM 5% 1/10

MCR03EZPJ471 470OHM 5% 1/10W

MCR03EZPJ391 390OHM 5% 1/10W

MCR03EZPJ103 10KOHM 5% 1/10W

MCR03EZPJ000 0OHM 5% 1/10W 1

MCR03EZPJ153 15KOHM 5% 1/10W

MCR03EZPJ472 4.7KOHM 5% 1/10

MCR03EZPJ101 100OHM 5% 1/10W

MCR03EZPJ103 10KOHM 5% 1/10W

MCR03EZPJ472 4.7KOHM 5% 1/10

MCR03EZPJ330 33OHM 5% 1/10W

MCR03EZPJ103 10KOHM 5% 1/10W

MCR03EZPJ472 4.7KOHM 5% 1/10

MCR03EZPJ330 33OHM 5% 1/10W

MCR03EZPJ100 10OHM 5% 1/10W

MCR03EZPJ330 33OHM 5% 1/10W

MCR03EZPJ000 0OHM 5% 1/10W 1

MCR03EZPJ100 10OHM 5% 1/10W

OTHERs

J901

J902

J904

J905

J906

Q901

X501

6630TGA005B

6630G100316

6602T20008E

6602T20008K

6630V90219A

0TFVI80067A

6212AA2004F

QH11121-DN0-D DVI 24P 1.90MM

DZ11AA1-HVG-PF D-SUB 15P 2.2

SMW200-06P 6P 2.00MM 1R STRA

SMW200-11P 11P 2.00MM 1R STR

SMW200-28C 28P 2.0MM 2R STRA

SI3865BDV(E3) N-CHANNEL MOSF

HC-49/U 14.31818MHZ 30PPM(TX

CONTROL BOARD

0RD7501Q609

0RD1801Q609

0RD1201Q609

140-058E

RDM94T1J7K50 7.5KOHM 5% 1/4W

RDM94T1J1K80 1.8KOHM 5% 1/4W

RDM94T1J1K20 1.2KOHM 5% 1/4W

THVV502GBC 1C1P 12VDC 0.05A

GDZJ5.6B 5.6V 5.45TO5.73V 60

SMAW200-06P 6P 2.00MM 1R ANG

SMAW200-03P 3P 2.00MM 1R ANG

BL-BY0BK201G-AB-LC4.5 ROUND

SW1

SW2

SW3

SW4

SW5

ZD1

ZD2

ZD3

140-058E

0DZ560009AG

6602T20009E

6602T20009B

EAV30486601

LED1

LGE Internal Use Only

Only for training and service purposes

- 28 -

DATE: 2007. 02. 06.

DESCRIPTION / SPECIFICATION

DATE: 2007. 02. 06.

DESCRIPTION / SPECIFICATION

*S *AL LOC. NO.

POWER BOARD

CAPACITORS

PART NO.

*S *AL LOC. NO.

PART NO.

D402

D403

D404

D405

D406

D407

D408

ZD101

ZD301

0DSDI00038A

0DZ330009CC

0DZGD00128A

"BAV99-(F),LF DIODES R/TP SOT"

MTZJ3.3B TP ROHM-K DO34 - 3.

ZMM5231B GRANDE REEL TAPING

C101

C103

C104

C105

C106

C107

C201

C202

C203

C204

C205

C206

C207

C208

C210

C301

C303

C304

C305

C306

C307

C308

C309

C310

C313

C314

C315

C317

C320

C402

C403

C404

C405

C406

C407

C409

C410

C411

C412

C413

C414

C415

C417

C418

C419

CX101

CY101

CY102

CY104

0CZZ9ST017A

AL EL CAPACITOR 100UF 450V 2

AL EL CAPACITOR 33UF 50V 20%

270PF 2012 50V 5% NP0 R/TP

AL EL CAPACITOR 0.47UF 50V 2

2200PF 2012 50V 5% COG R/TP

"0.1UF D 50V 80%,-20% F(Y5V)"

EKR3A102K09FK5 SAMWHA 1KV 10

AL EL CAPACITOR 1000UF 25V 2

AL EL CAPACITOR 680UF 25V 20

AL EL CAPACITOR 1000UF 16V 2

AL EL CAPACITOR 1000UF 25V 2

AL EL CAPACITOR 470UF 25V 20

330PF 1KV K R TP5.0 TAPING .

0.1UF 50V 10% X7R 2012 R/TP

C3216X7R1E225M TDK 25V 2.2UF

0.22UF 2012 25V 10% R/TP X7R

0.1UF 50V 10% X7R 2012 R/TP

1UF 2012 25V 10% X7R R/TP

0CZZ9ST014A

0CH5271K416

0CZZ9ST013A

0CK222DK4DA

0CK1040K945

0CKZTTA002E

0CZZ9ST021A

0CZZ9ST020A

0CZZ9ST018A

0CZZ9ST021A

0CZZ9ST019A

0CKZTTA002B

0CH3104K566

0CZZTCT006D

0CK224DH56A

0CH3104K566

0CK105DH56A

0CK224DH56A

0CK105DH56A

0CH2393K516

0CK152DK51A

0CH3103K516

0CH5221K416

0CZZTCT006D

0CK22201510

0CZZ9ST028A

0CH2153K516

0CK22201510

0CZZ9ST028A

0CH2153K516

0CK22201510

0CZZ9ST028A

0CH2153K516

0CK22201510

0CZZ9ST028A

0CH2153K516

0CH2222K516

0CZZ9ST025A

0CZZ9ST024A

0CZZ9ST023A

TRANSISTORs & ICs

Q101

Q301

Q302

Q303

Q304

Q305

Q306

Q307

Q308

U101

U201

U301

U303

U304

PC201

0TF760000AD

0TR144009AI

0TR144009AH

0TRKE80046A

0TR390609DC

0TFDI80001A

0TR390609DC

0TRKE80046A

0IPMG78425A

0IPMG78424A

0IPMG78426A

0TFAN00001A

0IPMG78432A

SSS7N60B FAIRCHILD ST TO220F

DTA144EK CHIP TP ROHM - -

DTC144EK CHIP TP ROHM - -

2N3904S KEC R/TP SOT23 60V 2

2N3906S-RTK KEC REEL TAPING

2N7002 DIODES R/TP SOT23 60V

2N3906S-RTK KEC REEL TAPING

2N3904S KEC R/TP SOT23 60V 2

FAN7601 FAIRCHILD DIP-8P BUL

"AZ431-A BCD 3P,TO-92 TAPING"

OZL68GN O2MICRO 20P SOP BULK

AP4511GD ADVANCED POWER ELEC

"LTV-817M-V(C) LITEON 4P, WID"

0.22UF 2012 25V 10% R/TP X7R

1UF 2012 25V 10% X7R R/TP

39000PF 50V 10% B(Y5P) 2012

1500PF 2012 50V 10% B(Y5P) R

10000PF 50V 10% B(Y5P) 2012

220PF 50V 5% NP0 2012 R/TP

C3216X7R1E225M TDK 25V 2.2UF

2200PF D 1KV 10% B(Y5P) R

RESISTORs

R101

R102

R103

R104

R105

R106

R107

R108

R109

R110

R111

R112

R115

R116

R117

R118

R202

R204

R205

R206

R207

R208

R209

R211

R301

R303

R304

R309

R310

R311

R313

R315

0RJ4703G676

0RJ6801E472

0RH1004D622

0RH1001D622

0RD0912Q609

0RH2201D622

0RD8203A609

0RD4702A609

0RX0560J609

0RX1003K607

0RD0471Q609

0RJ1302E472

0RJ4703G676

0RH2403D622

0RX0242K665

0RN3002F409

0RN2201F409

0RJ1601E472

0RH1001D622

0RH6800D622

0RH1001D622

0RJ1001G476

0RD1001Q609

0RH0222D622

0RD1002Q609

0RN1502F409

0RH1004D622

0RH1502D422

0RJ6202E472

0RH2001D622

470K OHM 1/4 W 5% 3216 R/TP

6800 OHM 1/8 W 1% 2012 R/TP

1M OHM 1 / 10 W 2012 5.00% D

1K OHM 1 / 10 W 2012 5.00% D

91 OHM 1/4 W (3.4) 5% TA52

2.2K OHM 1 / 10 W 2012 5.00%

820K OHM 1/2 W(7.0) 5.00% TA

47K OHM 1/2 W(7.0) 5.00% TA5

0.56OHM 1 W 5% TA52

CERAMIC DISK 10PF 6KV 5% TR

15000PF 50V 10% B(Y5P) 2012

2200PF D 1KV 10% B(Y5P) R

CERAMIC DISK 10PF 6KV 5% TR

15000PF 50V 10% B(Y5P) 2012

2200PF D 1KV 10% B(Y5P) R

CERAMIC DISK 10PF 6KV 5% TR

15000PF 50V 10% B(Y5P) 2012

2200PF D 1KV 10% B(Y5P) R

100KOHM 2 W 5% TA62

4.70 1/4W(3 5% TA52

CERAMIC DISK 10PF 6KV 5% TR

15000PF 50V 10% B(Y5P) 2012

2200PF 50V 10% B(Y5P) 2012 R

FILM CAPACITOR 0.47UF 275V 1

"Y CAPACITOR 100PF 250V 10%,-"

"Y CAPACITOR 4700PF 250V 20%,"

13K OHM 1/8 W 1% 2012 R/TP

470K OHM 1/4 W 5% 3216 R/TP

240K OHM 1 / 10 W 2012 5.00%

24 OHM 2 W 5% SF

30K OHM 1/6 W 1.00% TA52

2.2K OHM 1/6 W 1.00% TA52

1.6K OHM 1/8 W 1% 2012 R/TP

1K OHM 1 / 10 W 2012 5.00% D

680 OHM 1 / 10 W 2012 5.00%

1K OHM 1 / 10 W 2012 5.00% D

1K OHM 1/4 W 1% 3216 R/TP

1K OHM 1/4 W(3.4) 5.00% TA52

22 OHM 1 / 10 W 2012 5.00% D

10K OHM 1/4 W(3.4) 5.00% TA5

15K OHM 1/6 W 1.00% TA52

1M OHM 1 / 10 W 2012 5.00% D

"15K , 1/10W 1% TP"

DIODEs

BD101

D101

D102

D103

D201

D202

D306

D401

0DRTW00121A

0DRDI00234A

0DRDI00244A

0DSGF00019A

0DRNH00140A

0DRNH00130A

0DSGD00048A

0DSDI00038A

D2SB60-1121 TIWAN SEMI ST GB

PR1007 DIODES TAPING52 DO41

1N4007/L DIODES TAPING52 DO4

1N4148 GULF TP DO35 100V 0.1

FCH10U15 NIHON INTER BULK TO

FCH10U10 NIHON INTER BULK TO

MM4148 GRANDE REEL TAPING LL

"BAV99-(F),LF DIODES R/TP SOT"

62K OHM 1/8 W 1% 2012 R/TP

2K OHM 1 / 10 W 2012 5.00% D

LGE Internal Use Only

Only for training and service purposes

- 29 -

DATE: 2007. 02. 06.

DESCRIPTION / SPECIFICATION

*S *AL LOC. NO.

PART NO.

R316

R317

R318

R319

R320

R321

R401

R402

R403

R404

R406

R407

R408

R409

TH101

0RH2001D622

0RJ3303E472

0RJ1503E472

0RH1303D622

0RH1502D422

0RH1002D422

0RJ1001G476

0RJ3600E472

6322A00035A

2K OHM 1 / 10 W 2012 5.00% D

330000 OHM 1/8 W 1% 2012 R/T

150K OHM 1/8 W 1% 2012 R/TP

130K OHM 1 / 10 W 2012 5.00%

"15K , 1/10W 1% TP"

10K OHM 1/10 W 1% 2012 R/TP

1K OHM 1/4 W 1% 3216 R/TP

360 OHM 1/8 W 1% 2012 R/TP

10D2-07 SEMITEC 10OHM 15% L1

TRANSFORMER

T101

T301

T302

61709MC011A

61709MC010A

EER3016 430UH LX52 LIPS SMPS

EFD-2124 95UH INVERTER TRANS

OTHERs

SC101

F101

FB101

HS1

6620K00020A

0FZZTTH001E

6210TCE003G

4920900021A

4920900022A

4920900032A

61409B0009A

6200J000154

6602T20008K

6630V90218A

971-0016

HUAJIE AC UL/CSA 3PPIN BLACK

TIME LAG HBC 2153.15MXE(LEAD

BRS3550B BO SUNG 3550MM RADI

EXTRUSION 10*20 16 LX52

HS2

EXTRUSION 10*20 16 LX52

HS3

PLATE 7*60 16 LX52

HS4

PLATE 20.5 *10.5 *12.0

L202

LF101

P201

P401

P402

P403

P404

J30

HL-1520S JEONGSAN 7.0UH 25%

13.0*710*23680 SAMWAH BULK L

SMW200-11 YEONHO 11P 2.0MM L

"35001WR YEONHO 2P 3.5MM DIP,"

TIN HDC 0.60H NON NON

J31

971-0016

TIN HDC 0.60H NON NON

LGE Internal Use Only

Only for training and service purposes

- 30 -

SCHEMATIC DIAGRAM

1. SCALER

LGE Internal Use Only

Only for training and service purposes

- 31 -

2. POWER & WAFER

LGE Internal Use Only

Only for training and service purposes

- 32 -

3. INVERTER

LGE Internal Use Only

Only for training and service purposes

- 33 -

4. POWER

LGE Internal Use Only

Only for training and service purposes

- 34 -

Feb. 2007

P/NO : MFL43002807

Printed in Korea

JVC AV 21C14 User Manual
JVC CRT Television AV 36F475 User Manual
Kenwood DDX6027 User Manual
Lenovo J SERIES 8252 User Manual
Logitech Wireless All in One Keyboard TK820 User Manual
Marantz PD6120D User Manual
NEC MultiSync FE1250 User Manual
Nortel Networks Circuit Card User Manual
Panasonic KX TG6873B DECT 6 0 3 Handset Cordless Telephone KX TG6873B User Manual
Panasonic WV CK2020A User Manual