User’s Guide
L1770HQ
L1970HQ
L1970HR
Make sure to read the Important Precautions before using the product.
Keep the User's Guide(CD) in an accessible place for future reference.
See the label attached on the product and quote this information to your
dealer when you require service.
Important Precautions
On Installation
Do not allow anything to rest upon or roll over the power cord, and do not place
the display where the power cord is subject to damage.
Do not use this display near water such as near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming pool.
Displays are provided with ventilation openings in the cabinet to allow the release
of heat generated during operation. If these openings are blocked, built-up heat
can cause failures which may result in a fire hazard. Therefore, NEVER:
Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.
Place the display in a built-in enclosure unless proper ventilation is provided.
Cover the openings with cloth or other material.
Place the display near or over a radiator or heat source.
Do not rub or strike the Active Matrix LCD with anything hard as this may scratch,
mar, or damage the Active Matrix LCD permanently.
Do not press the LCD screen with your finger for a long time as this may cause
some afterimages.
Some dot defects may appear as Red, Green or Blue spots on the screen.
However, this will have no impact or effect on the display performance.
If possible, use the recommended resolution to obtain the best image quality for
your LCD display. If used under any mode except the recommended resolution,
some scaled or processed images may appear on the screen. However, this is
characteristic of the fixed-resolution LCD panel.
On Cleaning
Unplug the display before cleaning the face of the display screen.
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display
screen because over-spraying may cause electrical shock.
On Repacking
Do not throw away the carton and packing materials. They make an ideal
container in which to transport the unit. When shipping the unit to another
location, repack it in its original material.
On Disposal
The fluorescent lamp used in this product contains a small amount of mercury.
Do not dispose of this product with general household waste.
Disposal of this product must be carried out in accordance to the regulations of
your local authority.
A2
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor, the
computer system, and other attached devices is turned off.
For the desktop monitor, install the computer with the stand unfolded,
for ARM(wall mounting), install the computer with the stand folded.
Unfolding the stand base
1.
2. Place the monitor with its front facing downward on a cushion or soft cloth.
Press the downside of the stand base with your left hand as shown in the picture.
3.
4. With your left hand pressing the stand base, press the folding button using your right hand.
To release the folding, relieve the pressure on the left hand slowly with your right hand still
pressing the folding button.
5.
A spring is clicked on and the stand is brought out by itself from the standbase as shown in
6. the picture.
Pull out the stand as shown in the picture and the stand will hold up.
A3
Connecting the Display
Folding the stand base
1. Face the front of the monitor and push the monitor backwards, following the
sequence shown in the picture.
This illustration depicts the general model of connection. Your monitor may
differ from the items shown in the picture.
Do not touch or apply force to the monitor screen while expanding or
folding the stand base.
Positioning your display
1. Adjust the position of the panel in various ways for maximum comfort.
Tilt Range :0˚~30
2. The direction of the arrow indicates the direction to fold the product. It does not indicate
the degree of the usage.
Ergonomic
It is recommended that in order to maintain an ergonomic and comfortable viewing
position, the forward tilt angle of the monitor should not exceed 5 degrees.
A4
Connecting the Display
Using the Computer
1.
Connect the signal cable. When attached, tighten the thumbscrews to secure
2. the connection.
Connect the power cable with the AC adapter (AC power supply) ②, and
then plug the cable in the outlet. ③ (Voltage will be automatically controlled.)
Digital signal
DVI-D(optional)
Analog signal
D-SUB
DC 12V
JACK
When
connecting to a
wall concent
3
1
2
When connecting to a PC
AC adapter
PC
MAC
Mac adapter
For Apple Macintosh use, a separate plug adapter is needed to
change the 15 pin high density (3 row) D-sub VGA connector
on the supplied cable to a 15 pin 2 row connector.
PC
Digital signal DVI-D(optional)
A5
Connecting the Display
3.
Touch
button on the front switch panel to turn the power on. When
monitor power is turned on, the 'Self Image Setting Function' is
executed automatically.(Only Analog Mode)
NOTE
‘ Self Image Setting Function’? This function provides the user with optimal display
settings.When the user connects the monitor for the first time, this function automatically
adjusts the display to optimal settings for individual input signals. If you want to adjust the
monitor while in use, or wish to manually run this function once again, touch the
‘AUTO/SET’ button on the front panel of the monitor. Otherwise, you may execute the
‘FACTORY RESET’ option on the OSD adjustment menu. However, be aware that this
option initializes all the menu items except ‘LANGUAGE’.
A6
Control Panel Functions
Front Panel Controls
Bottom
Control
Function
Use this button to enter or exit the On Screen Display.
MENU Button
OSD LOCKED/UNLOCKED
This function allows you to lock the current control
settings, so that they cannot be inadvertently changed.
Touch and hold the MENU button for serval seconds.
The message "OSD LOCKED" should appear.
You can unlock the OSD controls at any time by touching
the MENU button for serva seconds. The message
"OSD UNLOCKED" should appear.
A7
Control Panel Functions
Control
Function
Use these buttons to select or adjust functions in the On
Screen Display.
+
Buttons
-
hot key
Button
-
For more information, refer to page A14
+
Button
SOURCE hot key
Use this button to make Dsub or DVI connector active.
This feature is used when two computers are connected
to the display. The default setting is Dsub.
Use this button to enter a selection in the On Screen
Display.
AUTO/SET
Button
AUTO IMAGE ADJUSTMENT
When adjusting your display settings, always touch
the AUTO/SET button before entering the On
Screen Display(OSD). This will automatically adjust
your display image to the ideal settings for the
current screen resolution size (display mode).
The best display mode is
17 inch monitor : 1280x1024
19 inch monitor : 1280x1024
Power Button
Use this button to turn the display on or off.
This Indicator lights up blue when the display
operates normally(On Mode). If the display is in Sleep
Mode (Energy Saving), this indicator color changes
to amber.
Power Indicator
A8
On Screen Display (OSD) Control Adjustment
Screen Adjustment
Making adjustments to the image size, position and operating parameters of
the display is quick and easy with the On Screen Display Control system. A
short example is given below to familiarize you with the use of the controls.
The following section is an outline of the available adjustments and selections
you can make using the OSD.
NOTE
Allow the display to stabilize for at least 30 minutes before making image adjustments.
To make adjustments in the On Screen Display, follow these steps:
AUTO/SET
MENU
MENU
+
+
-
-
Touch the MENU Button, then the main menu of the OSD appears.
To access a control, use the or
becomes highlighted, touch the AUTO/SET Button.
+
Buttons. When the icon you want
-
-
/
+
Buttons to adjust the image to the desired level. Use the
Use the
AUTO/SET Button to select other sub-menu items.
Touch the MENU Button once to return to the main menu to select another
function. Touch the MENU Button twice to exit from the OSD.
Automatic save
With the OSD open, once you have made an adjustment the monitor
automatically save any adjustments you have made, even if you exit the menu
or open another menu. If you make an adjustment and then wait for the
OSD to disappear, the adjustment will also been saved.
A9
On Screen Display(OSD) Selection and Adjustment
The following table indicates all the On Screen Display control, adjustment,
and setting menus.
Main menu
Sub-menu
A
D
Reference
BRIGHTNESS
CONTRAST
GAMMA
To adjust the brightness,
contrast and gamma of the
screen
PICTURE
PRESET
6500K
9300K
To customize the color of
the screen
COLOR
RED
GREEN
BLUE
HORIZONTAL
VERTICAL
CLOCK
To adjust the position of the
screen
POSITION
To improve the clarity and
stability of the screen
TRACKING
PHASE
To customize the screen
status for a user's operating
environment
LANGUAGE
SETUP
OSD
HORIZONTAL
POSITION VERTICAL
WHITE BALANCE
POWER INDICATOR
FACTORY RESET
MOVIE/TEXT
FLATRON
F-ENGINE(
To select or customize
desired image settings
-
)
USER
NORMAL
: Adjustable
A : Analog Input
D : Digital Input
NOTE
The order of icons may differ depending on the model (A10~A14).
A10
On Screen Display(OSD) Selection and Adjustment
You were introduced to the procedure of selecting and adjusting an item
using the OSD system. Listed below are the icons, icon names, and icon
descriptions of the all items shown on the Menu.
Touch the MENU Button, then the main menu of the OSD appears.
P I C T U R E
Menu Name
Sub-menus
Icons
Button Tip
MENU
: Exit
-
+
: Adjust (Decrease/Increase)
: Enter
SET
: Select another sub-menu
NOTE
OSD (On Screen Display) menu languages on the monitor may differ from the manual.
A11
On Screen Display(OSD) Selection and Adjustment
Main menu
Sub menu
Description
PICTURE
To adjust the brightness of the screen.
To adjust the contrast of the screen.
P I C T U R E
BRIGHTNESS
CONTRAST
GAMMA
Set your own gamma value. : -50/0/50
On the monitor, high gamma values
display whitish images and low gamma
values display high contrast images.
MENU : Exit
: Decrease
-
+
: Increase
SET : Select another sub-menu
COLOR
Select the screen color.
• 6500K: Slightly reddish white.
• 9300K: Slightly bluish white.
PRESET
C O L O R
Set your own red color levels.
Set your own green color levels.
Set your own blue color levels.
RED
GREEN
BLUE
MENU : Exit
: Decrease
-
+
: Increase
SET : Select another sub-menu
POSITION
P O S I T I O N
To move image left and right.
To move image up and down.
HORIZONTAL
VERTICAL
MENU : Exit
: Decrease
-
+
: Increase
SET : Select another sub-menu
A12
On Screen Display(OSD) Selection and Adjustment
Main menu
Sub menu
Description
TRACKING
T R A C K I N G
CLOCK
To minimize any vertical bars or stripes
visible on the screen background.The
horizontal screen size will also change.
PHASE
To adjust the focus of the display. This
item allows you to remove any
horizontal noise and clear or sharpen
the image of characters.
MENU : Exit
: Decrease
-
+
: Increase
SET : Select another sub-menu
SETUP
To choose the language in which the
control names are displayed.
LANGUAGE
S E T U P
OSD
POSITION
To adjust position of the OSD window
on the screen.
If the output of the video card is different
the required specifications, the color
level may deteriorate due to video
signal distortion. Using this function, the
signal level is adjusted to fit into the
standard output level of the video card
in order to provide the optimal image.
Activate this function when white and
black colors are present in the screen.
WHITE
BALANCE
-
+
M E N U
S E T U P
SET
-
+
M E N U
SET
Use this function to set the power
indicator on the front side of the monitor
to ON or OFF.
If you set OFF, it will go off.
If you set ON at any time, the power
indicator will automatically be turned on.
POWER
INDICATOR
MENU : Exit
: Adjust
-
+
: Adjust
SET : Select another sub-menu
FACTORY
RESET
Restore all factory default settings except
"LANGUAGE."
Press the
button to reset immediately.
If this does not improve the screen image, restore the factory default settings.
If necessary, perform the white balance function again. This function will be enabled only when
the input signal is an analog signal.
A13
On Screen Display(OSD) Selection and Adjustment
The OSD screen will appear when you touch the
front side of the monitor.
(-) button at the
Menu Name
Icons
Sub-menu Name
FLATRON F-ENGINE
Screen when applied Screen when not applied
When you execute F-ENGINE, two tones will appear
on the screen as shown. The applied screen will
appear on the left side, whereas the non-applied
screen will appear on the right side.Touch the
SETbutton to use the adjusted screen.
Main menu
Sub menu
Description
MOVIE
TEXT
This feature lets you easily select the best desired
image condition optimized to the environment
(ambient illumination, image types etc).
MOVIE For animation images in videos or movies
TEXT For text images (Word processing etc.)
USER User
You can manually adjust brightness, ACE or RCM.
You can save or restore the adjusted value even
when using a different environment setting.
To adjust the USER sub-menu function,
Press the SET Button
(Brightness): Adjusts screen brightness.
ACE(Adaptive Clarity Enhancer) Selects the clarity mode.
RCM(Real Color Management) Selects the color mode.
U S E R
BRIGHTNESS
Not applied
Green enhance
Flesh tone
Color Enhance
0
ACE
RCM
1
1
2
2
3
SAVE
M E N U
SET
SAVE
Select the
sub-menu using the SET
button and save the YES value using the -
buttons.
NORMAL
This is under normal operating conditions.
A14
Troubleshooting
Check the following before calling for service.
No image appears
Is the power cord of the
display connected?
Check and see if the power cord is connected
properly to the power outlet.
Is the power indicator
light on?
Touch the Power button.
Is the power on and the
power indicator blue or
green?
Adjust the brightness and the contrast.
Is the power indicator
amber?
If the display is in power saving mode, try moving
the mouse or pressing any key on the keyboard
to bring up the screen.
Try to turn on the PC.
Do you see an "OUT
OF RANGE" message
on the screen?
This message appears when the signal from the
PC (video card) is out of horizontal or vertical
frequency range of the display. See the
'Specifications' section of this manual and
configure your display again.
Do you see a "CHECK
SIGNAL CABLE
"message on the
screen?
This message appears when the signal cable
between your PC and your display is not
connected. Check the signal cable and try again.
Do you see a "OSD LOCKED" message on the screen?
You can secure the current control settings,
so that they cannot be inadvertently changed.
You can unlock the OSD controls at any time
by touching the MENU button for serval
seconds. The message "OSD UNLOCKED"
should appear.
Do you see “OSD
LOCKED” when you
touch MENU button?
A15
Troubleshooting
Display image is incorrect
Display Position is
incorrect.
Touch the AUTO/SET button to automatically
adjust your display image to the ideal setting.
If the results are unsatisfactory, adjust the image
position using the H position and V position
icon in the on screen display.
Check Control Panel --> Display --> Settings
and see if the frequency or the resolution were
changed. If yes, readjust the video card to the
recommend resolution.
On the screen
background, vertical
bars or stripes are
visible.
Touch the AUTO/SET button to automatically
adjust your display image to the ideal setting.
If the results are unsatisfactory, decrease the
vertical bars or stripes using the CLOCK icon in
the on screen display.
Any horizontal noise
appearing in any
image or characters
are not clearly
Touch the AUTO/SET button to automatically
adjust your display image to the ideal setting.
If the results are unsatisfactory, decrease the
horizontal bars using the PHASE icon in the on
screen display.
portrayed.
Check Control Panel --> Display --> Settings
and adjust the display to the recommended
resolution or adjust the display image to the ideal
setting. Set the color setting higher than 24 bits
(true color).
The screen color is
mono or abnormal.
Check if the signal cable is properly connected
and use a screwdriver to fasten if necessary.
Make sure the video card is properly inserted in
the slot.
Set the color setting higher than 24 bits (true
color) at Control Panel - Settings.
The screen blinks.
Check if the screen is set to interlace mode and if
yes, change it to the recommend resolution.
Make sure the power voltage is high enough, It
has to be higher than AC100-240V 50/60Hz.
A16
Troubleshooting
Have you installed the display driver?
Have you installed the
display driver?
Be sure to install the display driver from the
display driver CD (or diskette) that comes with
your display. Or, you can also download the
Do you see an
Make sure to check if the video card supports
Plug&Play function.
"Unrecognized monitor,
Plug&Play (VESA DDC)
monitor found"
message?
A17
Specifications
17inch
Display
17 inches (43.27cm) Flat Panel Active matrix-TFT LCD
Anti-Glare coating
17 inches viewable
0.264mm pixel pitch
Sync Input
Video Input
Horizontal Freq.
30 - 83kHz (Analog)
30 - 71kHz (Digital)
56 - 75Hz (Automatic)
Separate TTL, Positive/Negative
SOG (Sync On Green)
Digital
Vertical Freq.
Input Form
Signal Input
15 pin D-Sub Connector
DVI - D connector
Input Form
Max
RGB Analog (0.7Vp-p/75ohm), Digital
DVI Digital: VESA 1280 x 1024@60Hz
D-sub Analog: VESA 1280 x 1024@75Hz
VESA 1280 x 1024@60Hz
Resolution
Plug&Play
Recommend
DDC 2B
On Mode
:
35W
1W
1W
Power
Consumption
Sleep Mode
≤
≤
Off Mode
Full Up Position
Folded Position
Dimensions
&Weight
(with tilt stand)
Width
Height
Depth
Net
36.95 cm / 14.55inches
37.74 cm / 14.86 inches
23.65 cm / 9.31 inches
4.3 kg (9.48 lbs)
0˚~30˚
36.95cm / 14.55 inches
31.47cm / 12.39 inches
5.79 cm / 2.28inches
Til tRange
Tilt
12V
3A
Power Input
DVE. DSA-0421S-12 1
AC/DC Adapter
Operating Conditions
Environmental
Conditions
Temperature 10˚C to 35 ˚C
Humidity
10 % to 80 % non-Condensing
Storage Conditions
Temperature -20˚C to 60 ˚C
Humidity
5 % to 95 % non-Condensing
Tilt Stand
Attached( O ), Detachable (
)
Signal cable
Power cord
Attached( ), Detachable ( O )
Wall-outlet type or PC-outlet type
NOTE
Information in this document is subject to change without notice.
A18
Specifications
19inch
Display
19 inches (48.19cm) Flat Panel Active matrix-TFT LCD
Anti-Glare coating
19 inches viewable
0.294mm pixel pitch
Sync Input
Video Input
Horizontal Freq.
30 - 83kHz (Analog)
30 - 71kHz (Digital)
56 - 75Hz (Automatic)
Separate TTL, Positive/Negative
SOG (Sync On Green)
Digital
Vertical Freq.
Input Form
Signal Input
15 pin D-Sub Connector
DVI - D connector
Input Form
Max
RGB Analog (0.7Vp-p/75ohm), Digital
DVI Digital: VESA 1280 x 1024@60Hz
D-sub Analog: VESA 1280 x 1024@75Hz
VESA 1280 x 1024@60Hz
Resolution
Plug&Play
Recommend
DDC 2B
On Mode
:
39W
1W
1W
Power
Consumption
Sleep Mode
≤
≤
Off Mode
Full Up Position
Folded Position
Dimensions
&Weight
(with tilt stand)
Width
Height
Depth
Net
41.23 cm / 16.23inches
41.4 cm / 16.29 inches
23.65 cm / 9.31 inches
41.23 cm / 16.23inches
34.52cm / 13.59 inches
6.3 cm / 2.48inches
5.4 kg (11.91 lbs)
0˚~30˚
Til tRange
Tilt
12V
3A
Power Input
DVE. DSA-0421S-12 1
AC/DC Adapter
Operating Conditions
Environmental
Conditions
Temperature 10˚C to 35 ˚C
Humidity
10 % to 80 % non-Condensing
Storage Conditions
Temperature -20˚C to 60 ˚C
Humidity
5 % to 95 % non-Condensing
Attached( O ), Detachable (
)
Tilt Stand
Signal cable
Power cord
Attached( ), Detachable ( O )
Wall-outlet type or PC-outlet type
NOTE
Information in this document is subject to change without notice.
A19
Specifications
Preset Modes (Resolution)
Display Modes (Resolution)
Horizontal Freq. (kHz)
Vertical Freq. (Hz)
1
2
31.469
31.468
31.469
37.500
37.879
46.875
49.725
48.363
60.023
68.681
61.805
63.981
79.976
VGA
640 x 350
720 x 400
640 x 480
640 x 480
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1152 x 870
1152 x 900
1280 x 1024
1280 x 1024
70
70
60
75
60
75
75
60
75
75
65
60
75
VGA
3
VGA
4
VESA
VESA
VESA
MAC
5
6
7
8
VESA
VESA
MAC
VESA
VESA
VESA
9
10
11
*12
**13
* Recommend Mode
** Only Analog Mode
Indicator
MODE
LED Color
On Mode
Sleep Mode
Off Mode
blue
amber
0ff
A20
How to Install the VESA Standard wall mounting
This monitor meets VESA-compliant mounting interface pad
specifications.
1
■
Face the front of the monitor and push the monitor backwards, following
the sequence shown in the picture.
■Put the monitor on a soft cloth or cushion with its front facing downward.
2
3
■
Turn the 4 screws tight to the end of the standbase.
■Install the VESA standrad wall mounting.
VESA wall mounting
Kensington Security Slot- optional
Connected to a locking
cable that can be purchased
separately at most computer stores
Connected to another object (stand type
and wall-mounted type. This monitor
accepts a VESA-compliant mounting
interface pad.- optional)
For further information, refer to the VESA
Wall Mounting Instruction Guide.
A21
Digitally yours
|