TM
AI296
16-Port High Speed Multi-Protocol Line Card
User’s Guide
Version 9.8x
Part Number 296UM Rev 5
© 2008 by Kentrox, Inc. All rights reserved.
About this Document
This document explains how to install, configure, and operate the AI296 16-port high speed
multi-protocol line card.
You should have a working knowledge of the following:
z
z
z
z
z
z
Your network
AISwitchTM technology
X.25 protocol
Asynchronous protocols
TCP/IP
PC or asynchronous terminal configuration
i
AI296 Version 9.8x User’s Guide
About this Document: Document Conventions
Document Conventions
Table 1 describes the text conventions used in this document.
Table 1 Document Conventions
Convention
Meaning
Screen Text, Menu Items,
System Prompts, Messages
and Reports
This style indicates Kentrox configuration screen text,
menu items, system prompts, messages, and reports.
Static Command Text
Variable Command Text
...
In a command statement, this style indicates text that
should be entered exactly as shown at a command line.
In a command statement, this style indicates
user-specified text.
In a command statement, ellipses (...) signify that the
preceding parameter can be repeated a number of
times.
[ ]
In a command statement, square brackets indicate an
optional parameter. Two or more parameters in square
brackets with a vertical bar ( | ) between them indicate a
choice of optional parameters.
[ | ]
{ | }
In a command statement, two or more parameters in
braces with a vertical bar ( | ) between them indicate a
choice of required parameters.
Variable Field Text
This style indicates variable information you type in a
dialog box field.
KEYS
Uppercase body text indicates keys on a keyboard,
such as the TAB or ENTER keys. Keys used in
combination are connected with a plus symbol (+).
Labels
This style designates physical components on Kentrox
products such as jumpers, switches, and cable
connectors.
Note messages emphasize or supplement important
points of the main text.
ꢀ
Note:
Important:
Important messages provide information that is
essential to the completion of a task.
Tip messages provide information that assists users in
operating equipment more effectively.
Tip:
ii
AI296 Version 9.8x User’s Guide
About this Document: Document Conventions
Table 1 Document Conventions (Continued)
Convention
CAUTION:
Meaning
Caution messages indicate that failure to take a
specified action could result in loss of data and/or harm
to the software or hardware.
Warning messages indicate that failure to take a
specified action could result in physical harm to the
user.
WARNING:
iii
AI296 Version 9.8x User’s Guide
About this Document: Cautions and Warnings
Cautions and Warnings
Electrostatic Discharge Caution
CAUTION: Kentrox equipment and its peripherals contain electrostatic sensitive
components. Proper handling, shipping, and storage precautions must
be exercised:
z
You must remove and install cards in a static-free environment. Wear
an antistatic wrist strap that is plugged into the Kentrox equipment so
you are grounded at the same point as the equipment.
z
z
z
z
Do not remove cards from their antistatic plastic bags until you are
ready to install them into the chassis.
Immediately after you remove a card from the chassis, you must
insert it into its antistatic bag.
When the cards are not in use, keep them in their antistatic plastic
bags.
Do not ship or store cards near strong electrostatic, electromagnetic,
or radioactive fields.
Ground Caution
CAUTION: For Kentrox equipment to operate safely and correctly, there must be a
safety ground strap between the equipment ground bolts and the office
ground.
Proper Cooling Caution
ENSURE PROPER COOLING
CAUTION: When AI296 is installed into an AI180TM AIswitch series 180 chassis, the
chassis must be equipped with the AIcoolTM chassis cooling and Baffle-
HS heat baffle with sensor assemblies.
The AI180I AIswitch series 180 integrated chassis has a built-in fan and
baffle assembly and does not require additional assemblies.
iv
AI296 Version 9.8x User’s Guide
About this Document: Cautions and Warnings
FCC Warning
The Federal Communications Commission has set limits for emitted radio
interference, and AI296 is constructed with this electromagnetic interference (EMI)
limitation in mind. AI296 is classified under FCC regulations as a Class A device, that
is, a device for use in commercial environments and not in residential areas. This
device has been tested and shown to comply with the following FCC rule: Part 15
Subpart J. Operation of this equipment in a residential area may cause interference to
radio and TV reception, requiring the user to take whatever steps are necessary to
correct the interference.
Information is available from the FCC describing possible corrective actions. To
maintain low EMI levels, we suggest that you use only metal connectors and shielded
cable grounded to the frame.
Specifications are subject to change without notice.
v
AI296 Version 9.8x User’s Guide
About this Document: Customer Assistance
Customer Assistance
Kentrox offers technical support 24 hours a day, seven days a week.
Before you contact Kentrox for assistance, please have the following information
available:
z
z
The type of hardware and software you are using
The error number and exact wording of any messages that appeared on your
screen
z
z
What happened and what you were doing when the problem occurred
How you tried to solve the problem
Web Site Support
Support is available 24 hours a day using our Web site at:
http://www.kentrox.com
Email Support
Email support is available 24 hours a day. When you use email support, please be
sure to include the details of your problem within the email.
To contact Technical Support, send email to:
Phone Support
Phone support is available. When you call Kentrox for support, please be sure you
are at your computer and have the details of your problem available.
To contact Technical Support, call (866) 480-3571.
Kentrox Product Documentation
To order documentation, please contact your sales representative at
(800) 247-9482 or +1 (614) 798-2000.
You can also access and view the most current versions of Kentrox product
documentation on our Web site at:
http://www.kentrox.com
vi
Table of Contents
Features ....................................................................................................................... 1-2
BX.25 Compatibility .......................................................................................... 1-2
Dynamic Port Configuration ............................................................................. 1-2
Line Monitoring Diagnostics ............................................................................. 1-2
Link-to-Link Call Routing .................................................................................. 1-3
Front Panel Components ................................................................................. 1-6
DP196 Distribution Panel ................................................................................. 1-8
Typical Applications ................................................................................................... 1-11
Asynchronous to TCP/IP Application ............................................................. 1-11
X.25 Trunking ................................................................................................. 1-17
TM
Menu System ........................................2-1
Navigating the Menu System ....................................................................................... 2-3
Menu Numbering Structure .............................................................................. 2-3
TOC-1
Table of Contents
Exiting the Menu System ............................................................................................. 2-6
RADIUS Authentication .................................................................................... 3-2
Accessing the Local Menu System .............................................................................. 3-6
Identifying Types of Menu Items ...................................................................... 3-7
Accessing the Help Menu ............................................................................................ 3-9
Ethernet Port Settings ...................................................................................... 4-4
FTP Port ........................................................................................................... 4-5
IP Settings ........................................................................................................ 4-6
Passive Link Settings ....................................................................................... 4-8
TCP Settings .................................................................................................. 4-11
RADIUS Configuration ............................................................................................... 4-14
Shell/FTP Options .......................................................................................... 4-16
TACACS+ Configuration ............................................................................................ 4-18
Shell/FTP Options .......................................................................................... 4-19
SNMP Configuration .................................................................................................. 4-21
Authentication Traps ...................................................................................... 4-21
Static Route Configuration ......................................................................................... 4-27
TID to Modem Mux Configuration .............................................................................. 4-28
TOC-2
Table of Contents
Inactivity Timeout ........................................................................................... 4-28
Initialization String .......................................................................................... 4-29
Time Zone ...................................................................................................... 4-36
Local IP Subnet Mask ...................................................................................... 5-4
Remote X.121 Address .................................................................................... 5-7
AI296 Link Types ......................................................................................................... 6-2
Asynchronous PPP .......................................................................................... 6-2
HDLC-Bridge .................................................................................................... 6-3
MLT .................................................................................................................. 6-3
Synchronous PPP ............................................................................................ 6-3
X.25 .................................................................................................................. 6-4
BX.25 Configuration ..................................................................................................... 6-5
BX.25 Support .................................................................................................. 6-7
BX.25 Timer Settings ....................................................................................... 6-8
Connection Settings ....................................................................................... 6-14
Link Application .............................................................................................. 6-16
Disconnect Inactivity Timer Settings .............................................................. 6-18
TOC-3
Table of Contents
Disconnect String ........................................................................................... 6-21
Auto Disable Error Limit ................................................................................. 6-23
Flow Control ................................................................................................... 6-24
Hardware Interface (Interface Type) .............................................................. 6-25
Interface Mode ............................................................................................... 6-27
Link Number ................................................................................................... 6-30
Link State ....................................................................................................... 6-31
Port Data Bits ................................................................................................. 6-34
Port Speed ..................................................................................................... 6-36
Port Stop Bits ................................................................................................. 6-38
General PPP Properties Configuration ...................................................................... 6-42
Maximum Unit Settings .................................................................................. 6-44
Network Control Protocol ............................................................................... 6-45
Frame Settings ............................................................................................... 6-47
Interface Mode ............................................................................................... 6-48
N2 Retry Counter ........................................................................................... 6-50
Modem Option Configuration ..................................................................................... 6-52
Modem String ................................................................................................. 6-52
Dialing Time-out Interval ................................................................................ 6-53
Number of Dial Attempts ................................................................................ 6-54
RAS Option .................................................................................................... 6-58
Quick X.25 Configuration ........................................................................................... 6-62
Frame Settings ............................................................................................... 6-62
Interface Mode ............................................................................................... 6-63
Number of PVCs ............................................................................................ 6-64
Packet Settings .............................................................................................. 6-65
Passive Link Settings ..................................................................................... 6-66
Port Speed ..................................................................................................... 6-67
SVC Settings .................................................................................................. 6-68
TOC-4
Table of Contents
X.121 Local Address ...................................................................................... 6-69
DTR State Configuration ................................................................................ 6-71
RTS State Configuration ................................................................................ 6-72
Protocol Version ............................................................................................. 6-77
X.25 Counter Settings .................................................................................... 6-78
X.121 Local Address ...................................................................................... 6-84
Virtual Circuit Configuration ....................................................................................... 6-85
Number of PVCs ............................................................................................ 6-85
Overview ......................................................................................................................7-2
Example Configurations ................................................................................. 7-10
Overview ......................................................................................................................8-2
Call Routing ..................................................................................................................8-5
Configuring an Alias with X.25 Keep-Alive ..................................................... 8-10
Module Properties .......................................................................................... 8-36
Alias Macro Components ............................................................................... 8-38
TOC-5
Table of Contents
Alias Macro Configuration .............................................................................. 8-43
Alias Configuration Examples .................................................................................... 8-45
SVC to SVC Connection ................................................................................ 8-45
SVC to PVC Connection ................................................................................ 8-47
PVC to SVC Connection ................................................................................ 8-49
Link-to-Link Call Routing ................................................................................ 8-53
Shell Commands .............................................................................................. 9-2
Shell Connections ............................................................................................ 9-2
winslc Commands ........................................................................................................ 9-4
aaa ............................................................................................................................... 9-6
alarm .......................................................................................................................... 9-12
arp .............................................................................................................................. 9-16
break .......................................................................................................................... 9-19
bridge ......................................................................................................................... 9-21
creset ......................................................................................................................... 9-22
date ............................................................................................................................ 9-23
debug .........................................................................................................................9-24
delete ......................................................................................................................... 9-26
diag-conn ................................................................................................................... 9-27
diag-eth ......................................................................................................................9-29
diag-info .....................................................................................................................9-37
diag-tconn .................................................................................................................. 9-49
dir ............................................................................................................................... 9-50
head ........................................................................................................................... 9-52
help ............................................................................................................................ 9-53
id ................................................................................................................................ 9-55
ip ................................................................................................................................ 9-56
link .............................................................................................................................. 9-59
linkstat ........................................................................................................................ 9-61
log .............................................................................................................................. 9-64
logout ......................................................................................................................... 9-65
menu ..........................................................................................................................9-67
more ........................................................................................................................... 9-68
pad ............................................................................................................................. 9-69
TOC-6
Table of Contents
passwd ....................................................................................................................... 9-72
ping ............................................................................................................................ 9-73
profile ......................................................................................................................... 9-76
pvcedit ........................................................................................................................ 9-78
pvclist ......................................................................................................................... 9-80
reset ........................................................................................................................... 9-82
rz ................................................................................................................................ 9-83
selcnf .......................................................................................................................... 9-84
show ........................................................................................................................... 9-86
staslc .......................................................................................................................... 9-92
syncflash .................................................................................................................... 9-94
tacacs ......................................................................................................................... 9-96
tftp ............................................................................................................................ 9-105
tftpboot ..................................................................................................................... 9-108
trace .........................................................................................................................9-112
traceroute ................................................................................................................. 9-114
type ..........................................................................................................................9-115
update ...................................................................................................................... 9-116
uptime ...................................................................................................................... 9-117
useradd .................................................................................................................... 9-118
userdel ..................................................................................................................... 9-120
users ........................................................................................................................ 9-121
who ...........................................................................................................................9-122
xvc ............................................................................................................................ 9-123
Standard ISO Diagnostic Codes ......................................................................A-4
TOC-7
Table of Contents
Crash Codes ................................................................................................................A-8
System Failure Crash Reports .......................................................................A-10
Configuring BOOTP/TFTP ...............................................................................B-3
AI296 Commands ........................................................................................................C-2
AI296 Menu Aliases .....................................................................................................C-3
TOC-8
AI296 Version 9.8x User’s Guide
Product Description: Features
Features
The AI296 16-port high speed multi-protocol line card provides 16 physical ports for
asynchronous or X.25 connections between NEs and OSSs in a carrier’s network.
AI296 includes the following features:
Break Propagation
AI296 supports break propagation on X.25, asynchronous, or TCP protocols. Refer to
break handling.
BX.25 Compatibility
AI296 is BX.25 compatible and supports passive links.
DCD/DSR/RTS/DTR Signal Lead Control
AI296 supports user selectable disconnect on DCD low, DCD high-to-low transition,
DSR low, and DSR high-to-low transition. Additionally, AI296 allows for user
selectable connection control of DTR/RTS.
Dynamic Port Configuration
Any X.25 or asynchronous parameter can be changed and individual links can be
reconfigured without resetting AI296. X.25 and asynchronous parameters take effect
after disabling and then re-enabling the affected link.
EIA Lead Signaling
AI296 can program the disconnected and connected states of EIA signals and toggle
the leads. The system can use EIA signaling to simulate modem style access to host
computers. These signaling options provide a secure and flexible connection to any
details.
IRB Connectivity
AI296 communicates with other cards in the same chassis over an internal repeater
bus. It cannot communicate over the backplane with line cards that do not use the
IRB.
Line Monitoring Diagnostics
X.25 line monitoring diagnostics are available from the shell connection. Refer to
1-2
AI296 Version 9.8x User’s Guide
Product Description: Features
Link-to-Link Call Routing
Link-to-link call routing lets users route all SVC calls coming in on one X.25 link to
another X.25 link. By using X.25 link-to-link call routing, it is now possible to create a
default route for all calls from a specified X.25 link. The alias for the default link-to-link
route can route all calls destined for the same link. On previous versions of AI296,
users had to create an alias for each unique called address.
Performance Monitoring, Maintenance, Troubleshooting
Shell and winslc commands let users handle performance monitoring, maintenance,
and troubleshooting for AI296.
Remote and Local Configuration
AI296 can be configured from AI198TM by accessing the AI198 menu system. AI198 is
accessible using a Telnet session or by plugging a terminal into the AI198 Craft port.
Simultaneous Connections
AI296 supports up to 1024 simultaneous X.25 to IP and/or IP to X.25 virtual
connections. It supports 512 simultaneous X.25 to X.25 virtual connections or child
connections. These connections may be distributed in any combination across the 16
available serial ports on AI296.
Single Alias Translation
Single alias translation allows routing a call from an incoming link on one AI296 to an
outgoing link on a second AI296/AI232TM/AIscoutTM with a single alias. Generally, this
feature is used to route an X.25 connection across two AI296/AI232/AIscout cards
using TCP/IP.
SNMP Manageability
AI296 supports configuration using SNMP as well as monitoring. SNMP traps are
generated by AI296 and are sent to all the management stations that exist in the trap
table.
Standalone Configuration
AI296 operates as a standalone card when it is installed in the AIswitch series 110
chassis. Standalone mode lets AI296 function without dependence on AI198 for
Mode for more details.
1-3
AI296 Version 9.8x User’s Guide
Product Description: Features
System Diagnostics
AI296 lets users view diagnostic data on existing connections and internal information
about serial links. For more information about viewing system diagnostics, refer to
sections:
z
z
z
z
z
TID Multiplexing
TID multiplexing allows a single call from a legacy X.25 OSS to fan out into multiple
calls to various NEs. The initiating call may be X.25, asynchronous, or TCP. Refer to
1-4
AI296 Version 9.8x User’s Guide
Product Description: AI296 Hardware Components
AI296 Hardware Components
AI296 has four high density connectors that provide 16 asynchronous, HDLC-Bridge,
PPP, or X.25 ports. Individual ports are derived by using a cable assembly or a
distribution panel. Protocol changes to a single port can be made without interrupting
communications on the other ports. Each port operates at speeds up to 115 kilobits
per second asynchronous or 128 kilobits per second synchronous.
AI296 supports both X.25 and TCP/IP protocols and provides concurrent X.25,
TCP/IP, HDLC-Bridging, and asynchronous functionality. An Ethernet port is available
on the front panel or on the backplane interface (IRB). AI296 uses the IRB to transfer
data to and from other cards in the system and network.
AI296 can be used in an AI shelf with other AI network interface cards to provide
single, multiple, and redundant trunk lines with a variety of physical port and protocol
types, including:
z
z
z
z
z
z
z
z
EIA-232
EIA-530
X.25
V.35
IP
Asynchronous
PPP
HDLC-Bridge
When combined with other AI network interface cards, typical applications include
collection, concentration and trunking of alarm and event messages from many NEs
to one or more OSSs and operations centers.
AI296 meets Bellcore Network Equipment Building Standards (NEBS) to ensure
reliable operations in Central Offices and other telecommunications facilities.
CAUTION: AIswitch and its peripherals contain electrostatic sensitive components.
Exercise proper handling, shipping, and storage precautions.
1-5
AI296 Version 9.8x User’s Guide
Product Description: AI296 Hardware Components
Front Panel Components
Figure 1-1 displays the AI296 front panel components.
DC OK LED
Illuminates green when +5 Volts are
present.
FAULT LED
Illuminates red if the card fails.
DC OK
FAULT
LINKS 5-8 Connector
Provides four asynchronous, HDLC-
Bridge, PPP or X.25 ports.
LINKS 13-16 Connector Provides four asynchronous, HDLC-
Bridge, PPP or X.25 ports.
LINKS 1-4 Connector
LINKS 9-12 Connector
ACT LED
Provides four asynchronous, HDLC-
Bridge, PPP or X.25 ports.
LINKS
13-15
Provides four asynchronous, HDLC-
Bridge, PPP or X.25 ports.
LINKS
5-8
Illuminates green when the card is
transmitting or receiving packets.
LINK LED
Illuminates green when valid link integrity
pulses are being received.
COL LED
Illuminates red when collisions are
detected.
10BASET Connector
Specifies the external 10BaseT port
connector.
LINKS
9-12
LINKS
1-4
10
B
A
S
E
T
AI296
Figure 1-1
AI296
1-6
AI296 Version 9.8x User’s Guide
Product Description: Technical Specifications
Technical Specifications
Table 1-1 lists the AI296 technical specifications.
Table 1-1 Technical Specifications
Description
Component
I/O Ports
16 asynchronous, HDLC-Bridge, PPP or X.25 (selectable
per port during configuration)
ꢀ
Note: Individual ports are derived by using a CAB257 cable
assembly for each connector or by using the Model
DP196 distribution panel.
Port Speed
300 bps to 128 Kbps or external clocking (selectable per port
during configuration)
Electrical Interfaces RS-232, RS-530, and V.35 (selectable per port during
configuration)
Installation
Requires one slot in an AI chassis (can be hot swapped)
4.2 A at +5 VDC, maximum
Current Draw
Compliance
For use with AI UL Listed AIswitch Series Chassis.
1-7
AI296 Version 9.8x User’s Guide
Product Description: Individual Port Access
Individual Port Access
Individual ports are accessed by using a cable assembly or a distribution panel. AI296
uses the following components to derive ports:
z
z
CAB257 Cable
The CAB257 cable has a multi-connector end that provides four DB-25 connectors.
Four CAB257 cables are needed to derive all 16 ports.
DP196 Distribution Panel
The DP196 distribution panel provides the physical interface for AI296 with sixteen
DB-25 connectors. The distribution panel is available in two sizes for 19-inch or 23-
the specifications.
LINK
LINK
1
2
LINK
LINK
5
6
LINK 1
LINK 2
LINK
LINK
5
6
LINK
LINK
3
4
LINK
LINK
7
8
LINK 3
LINK 4
LINK
LINK
7
8
Figure 1-2 DP196-19/23 Distribution Panel
Table 1-2 DP196-19/23 Specifications
Description
Specification
Mounting
DP196-19—Mounts to a 19-inch rack
DP196-23—Mounts to a 23-inch rack
I/O Ports
Sixteen DB-25 connectors
Weight (approximately) 2.5 lb. (1.12 kg)
Size
Height: 4 in. (10.16 cm)
Width: 19 in.(48.26cm)/23in. (58.42 cm)
Depth: 1.12 in. (2.84 cm)
Cable
CAB162—Connects one connector (4 ports) on AI296 to
the distribution panel. Each distribution panel requires
four cables.
1-8
AI296 Version 9.8x User’s Guide
Product Description: Individual Port Access
DB-25 Connectors
Table 1-3 displays pin assignments for the DB-25 connectors on the DP196-19/23
distribution panel.
Pin 1
Pin 14
Pin 25
Pin 13
Figure 1-3 DB-25 connector Pin Assignments
Table 1-3 displays the DP196-19/23 pin assignment specifications.
Table 1-3 DP196-19/23 Pin Assignment Specifications
Pin
Signal
Direction
2
TXD-
Output
Input
Output
Input
----
3
RXD-
4
RTS-
5
CTS-
7
Signal GND
DCD-
RXC+
DCD+
TXC+
CTS+
TXD+
TXC-
8
Input
Input
Input
Either
Input
Output
Either
Input
Input
9
10
12
13
14
15
16
17
RXD+
RXC-
1-9
AI296 Version 9.8x User’s Guide
Product Description: Individual Port Access
Table 1-3 DP196-19/23 Pin Assignment Specifications (Continued)
Pin
Signal
Direction
19
20
23
RTS+
DTR-
DTR+
Output
Output
Output
The following characteristics apply to pin assignments:
z
z
z
Any pin assignment not referenced on a connector is not connected.
Signals with a (-) sign after them are used when RS-232 is selected.
Signals with both (+) and (-) after them are used when RS-530, V.35, or V.11 are
selected.
z
When RS-530 is selected, both the (+) and the (-) signals are used. The DSR is
only supported in RS-232 mode. There is no DSR+ signal.
ꢀ
Note: The pin assignments also apply to CAB257.
RJ45 10BaseT Connectors
Figure 1-4 displays the RJ45 10BaseT connector.
Pin 1
Pin 8
Figure 1-4 RJ45 10BaseT Connector on an AI296 Front Panel
Figure 1-4 lists the specifications for the RJ45 10BaseT connector.
Table 1-4 RJ45 10BaseT Connector Specifications
Pin
Signal
Direction
1
2
3
6
TD+
TD-
Output
Output
Input
RD+
RD-
Input
CAB182 cables connect network elements to the individual connectors on the
distribution panel (straight through applications).
1-10
AI296 Version 9.8x User’s Guide
Product Description: Typical Applications
Typical Applications
AI296 is used primarily for X.25 trunking and connecting different types of network
elements. The following applications are discussed in this section:
z
z
z
z
z
Asynchronous to TCP/IP Application
Figure 1-5 illustrates an asynchronous to TCP/IP application.
Asynchronous NE
Asynchronous NE
Asynchronous NE
IP Network
Operating Support System
AI296
Figure 1-5 Asynchronous to TCP/IP Application
1-11
AI296 Version 9.8x User’s Guide
Product Description: Typical Applications
z
z
The OSS sends TCP/IP calls to AI296.
AI296 routes the TCP/IP calls to an asynchronous NE using an asynchronous
port.
IP Over X.25 Networks
Figure 1-6 illustrates a common IP over X.25 application.
SNMP
Manager
SNMP
Manageable
Device
(example
AI198)
X.25 Packet
Network
IP Network
IP Network
AI296
AI296
IP Over Ethernet
IP Over Ethernet
Figure 1-6 IP Over X.25 Network
configured to encapsulate IP packets, making it possible to achieve IP connectivity
across a legacy X.25 network. The most common application for this functionality is to
transport SNMP management information across an X.25 network.
Important: IP/X.25 transport works only over SVCs.
1-12
AI296 Version 9.8x User’s Guide
Product Description: Typical Applications
Figure 1-6 on page 1-12 illustrates the following events:
z
The SNMP Network Manager (for example, AppliedView) sends TCP/IP calls over
an IP/Ethernet network to AIswitch (AI296).
z
AI296 encapsulates the TCP/IP calls within X.25 SVC calls and sends them
through the X.25 packet network.
z
z
The X.25 packet network sends the X.25 calls to a remote AIswitch (AI296).
The remote AI296 returns the X.25 calls to TCP/IP calls based on its static routing
tables.
z
AI296 sends the TCP/IP calls over the IP/Ethernet network to the
SNMP-managed device (for example, AI198).
1-13
AI296 Version 9.8x User’s Guide
Product Description: Typical Applications
Mixed Asynchronous and X.25 Networks
Figure 1-7 illustrates both X.25 network elements and asynchronous network
elements connected to a remote OSS using a single X.25 trunk.
DDM 2000
X.25 Packet
Network
FLM 150
Operating
Support System
AI296
Titan DACS
IRB
DDM 2000
FLM 150
Titan DACS
AI296
Asynchronous NE
Figure 1-7 Mixed Asynchronous and X.25 Network
1-14
AI296 Version 9.8x User’s Guide
Product Description: Typical Applications
Figure 1-7 illustrates the following events:
z
z
z
z
The OSS sends X.25 calls through an X.25 packet network to AI296.
AI296 makes call routing decisions based on the AI198 routing alias.
AI296 sends local X.25 calls directly to the attached NEs.
The local AI296 converts local X.25 calls to TCP/IP calls and routes them over the
IRB to a remote AI296. Routing is based on the routing aliases configured in
AI198.
z
The remote AI296 sends asynchronous calls to the attached asynchronous NEs.
1-15
AI296 Version 9.8x User’s Guide
Product Description: Typical Applications
X.25 to TCP/IP Application
Figure 1-8 illustrates a common X.25 to TCP/IP application. X.25 network elements
are connected to a router network using a TCP/IP LAN.
AIswitch
IRB
Operating
Support System
X.25 NE
X.25
X.25 NE
TCP/IP Network
AIfocus
AI296
X.25 NE
AIswitch
TCP/IP
X.25
Figure 1-8 X.25 to TCP/IP Application
Figure 1-8 illustrates the following events:
z
z
The OSS sends X.25 calls to AIswitch.
AIswitch converts X.25 calls to TCP/IP calls and sends them over the router
network.
z
z
z
z
The router network carries the TCP/IP calls to AIfocusTM.
AIfocus sends the TCP/IP calls over the IRB to AI296.
Based on the AI198 routing alias, AI296 converts the TCP/IP calls to X.25 calls.
AI296 sends X.25 calls to the attached X.25 NEs.
Like other AIswitch line cards, AI296 terminates X.25 connections and extracts the
data from them. Unlike other line cards, AI296 can convert the X.25 connections to
TCP/IP connections across the IRB. The ultimate destination for these TCP/IP
connections may be one of the following:
z
An IRB-connected line card in the same chassis, such as another AI296 or an
AI193-TXTM
z
z
A locally connected TCP/IP host
A remote TCP/IP host, indirectly connected to AIswitch using a router network.
When AI296 establishes a TCP/IP connection to an external device, the IP packets
are exported from AIswitch by AIfocus or by an AI router.
1-16
AI296 Version 9.8x User’s Guide
Product Description: Typical Applications
X.25 Trunking
Figure 1-9 illustrates a common X.25 trunking application.
X.25 NE
X.25 Packet
Network
X.25 NE
X.25 NE
Operating
Support System
AI296
X.25 NE
X.25 NE
X.25 NE
AI296
Figure 1-9 X.25 Trunking
1-17
AI296 Version 9.8x User’s Guide
Product Description: Typical Applications
Figure 1-9 illustrates the following events:
z
The OSS sends X.25 calls through an X.25 packet network (over an X.25 trunk) to
AI296.
z
z
AI296 makes call routing decisions based on the AI198 routing alias.
AI296 sends local X.25 calls directly to its attached NEs. X.25 NEs are connected
to the OSS with a single X.25 trunk.
z
z
AI296 converts local X.25 calls to TCP/IP calls and sends them over the IRB to a
remote AI296.
The remote AI296 sends remote X.25 calls directly to its attached network
elements.
1-18
AI296 Version 9.8x User’s Guide
TM
Using the AI198 Menu System: Accessing the Menu System
Accessing the Menu System
To access the AI198 menu system:
1. Log into AI198.
2. At the prompt, enter menu. The Main Menu appears.
>menu
Main Menu
01+Configure options affecting the system as a whole
02+Create, delete, or modify a destination name
03+Display all destination names
04+Configure cards
05+Set or remove connection restrictions based on port numbers
06+Display all connection restrictions
07+Configure slot density
08+Configure the alias translation table
09+Display the list of alias translation entries
10+Configure the BOOTP table
21 Exit the configuration menu system
Enter item number and optional ",value" then push <CR> key
>
2-2
AI296 Version 9.8x User’s Guide
Using the AI198 Menu System: Navigating the Menu System
TM
Navigating the Menu System
Menu Numbering Structure
All menus accessed from the Main Menu are identified with a numerical reference at
the top right corner of the menu screen. This numerical reference specifies the
location within the menu system. Each digit in the menu number represents a menu
item that was previously selected. For example, Menu 4.2 indicates that menu item 4
and 2 were selected.
>2
Menu 4.2
01 Configure as Empty Slot
02+Configure as AI183/AI185 standard 4/16 port card
03+Configure as AI193/194 Ethernet card with slot expansion of-----
04+Configure as AI192/196 X.25 network card with slot expansion of--------
05+Configure as ASP or Advanced Smart Line Card with slot expansion of--------
06 Configure as AI196-I network card with LocalView
07 Configure as AI2524 Router card
08 Configure as AI294 Ethernet Switch card
09+Configure as AI196-I network interface card with menu support
10 Configure as Independent Smart Line Card
11+Configure as AI296 network interface card
12+Configure as AI192/196 with full menu support and slot expansion of--------
13+Configure as AI285 network interface card
14+Configure as AI232 network interface card
15 Configure as AI Modem
16 Configure as AIFlex Fiber LAN Extender Card
17 Configure as AI120 Card
18 Configure as AIE1 Card
19 Configure as AITC Card
20 Next Page
21 Exit this menu with no changes
Enter item number and optional ",value" then push <CR> key
>
Types of Menu Items
The following four types of menu items are available:
z
z
z
z
2-3
AI296 Version 9.8x User’s Guide
TM
Using the AI198 Menu System: Navigating the Menu System
Submenus
Submenus go to deeper levels in the menu hierarchy. They provide additional
configuration menus. Menu items that contain submenus have a plus sign (+) next to
their menu item number. In this example, menu item 02 will display a submenu.
02+Configure as AI232 network interface card
Some submenus require a selection from a list and then re-display the previous menu
showing the selection. Other submenus have their own submenus that request
additional information. After saving the entries, the top-level menu re-appears.
Toggles
Toggles display two or more values that can be selected for a parameter. Toggles
have an asterisk (*) next to their menu item number. Entering the menu item number
toggles to the next selection.
In this example, menu items 06 and 07 are toggles.
06*TCP Default Window Size (200, 512, 1024, 2048)-------------------------- 200
07*TCP Send Ahead-----------------------------------------------------------OFF
For 06*TCP Default Window Size, the user can toggle between values 200, 512, 1024, and
2048. For 07*TCP Send Ahead, the user can toggle between ON and OFF.
Data
Data menu items request text entries (such as destination names and card
descriptions) or numeric values (such as port numbers and IP addresses). To enter
information in a data menu item, enter the menu item number followed by a comma
(or a space) and the configuration information.
In this example, the menu item requires an IP address entry.
01 IP Address (0.0.0.0 - 255.255.255.254)-----------------------000.000.000.000
To enter an IP address of 172.016.002.043, enter the following:
1,172.016.002.043
The menu re-appears with the entered IP address.
01 IP Address (0.0.0.0 - 255.255.255.254)-----------------------172.016.002.043
To change configuration data that has been entered for a menu item, enter the menu
item number followed by a comma and the new data.
2-4
AI296 Version 9.8x User’s Guide
Using the AI198 Menu System: Navigating the Menu System
TM
Tip: To change a typed entry, use BACKSPACE to back up to the desired position in
the text and retype the changes. However, once the user presses ENTER,
changes can be made only by selecting that menu item and re-entering the
data.
Functions
Menu item functions appear at the bottom of each menu. This example displays menu
17 Display first page
18 Next page
19 Delete entry
20 Save the changes made
21 Exit this menu with no changes
Enter item number and optional ",value" then push <CR> key
>
Table 2-1 Menu Item Descriptions
Menu Item Description
17
18
19
20
Displays the first page of a menu.
Displays additional pages of a menu.
Deletes information for a specified entry.
Saves the entered information and re-displays the previous related
menu.
Important: Configuration entries take effect only after every screen
has been saved going back to the main menu.
21
Exits a menu without saving changes. All items on the menu return to
the previously configured values.
2-5
3
AI296 Local Menu System
This chapter provides information on the configuration and navigation of the AI296 menu system.
This system offers on-board configuration capabilities similar to those available in the AI198
menu system. The AI296 menu system is available when the card is operating in both switch
mode and standalone mode.
Guide to this Chapter
3-1
AI296 Version 9.8x User’s Guide
AI296 Local Menu System: Identifying AI296 Menu System Security Options
Identifying AI296 Menu System Security Options
AI296 has a variety of security options, including:
z
z
z
z
Multilevel User Name and Password Security
Up to 10 configurable user account profiles can be assigned to an AI296 user. Five
system profiles are available for providing various levels of user access. For more
information about user profiles, refer to command profile on page 1-103.
RADIUS Authentication
RADIUS authentication verifies user login information against valid user information in
a database on a centralized RADIUS authentication server. A primary and secondary
RADIUS server are configurable to provide secure access for an entire AI296
network. AI296 RADIUS authentication is available for Telnet, asynchronous, and
synchronous ports. For more information on RADIUS authentication, refer to section
RADIUS Configuration on page 1-19.
TACACS+ Authentication
TACACS+ authentication verifies user login information against the user’s permission
level on a TACACS+ server. Up to 9 TACACS+ servers are configurable to provide
secure access for an entire AI296 network. AI296 TACACS+ authentication is
available for Telnet, asynchronous, and FTP connections. For more information on
TACACS+ authentication and server configuration, refer to the following commands:
z
z
z
PPP Authentication Protocols (PAP and CHAP)
All asynchronous and synchronous PPP links are configurable to use either PAP or
CHAP PPP authentication protocols. PAP establishes peer identity using a 2-way
handshake that is done only upon initial link establishment. CHAP performs a 3-way
handshake upon initial link establishment, then proceeds to verify the link with 3-way
handshakes at random intervals. CHAP also encrypts the user’s password over the
PPP link to provide added security.
3-2
AI296 Version 9.8x User’s Guide
AI296 Local Menu System: Logging Into AI296
Logging Into AI296
Log into AI296 with a Telnet connection or with any of AI296’s asynchronous ports
that are configured as Login ports.
ꢀ
Note: ai is the default user ID and password. AI296 prompts you to create a new
user ID and password after the fifth login with the default values. Refer to
Using a Telnet Connection for Login
Logging in using a Telnet connection requires that AI296 has a configured IP address.
assign an IP address.
To log into AI296 using a Telnet connection:
1. Power on AI296.
2. Connect the Ethernet network connection to the 10BaseT port on the front panel
of AI296.
3. Telnet to AI296. The login prompt appears.
ꢀ
Note: ai is the default user ID and password. There are five grace period logins.
If after the fifth login a new ID and password have not been created, AI296
prompts you to create a user ID and password. Use the useradd
and password.
4. Enter your user ID. The password prompt appears.
5. Enter your password. The destination menu appears. You are now logged into
AI296.
The following message appears when AI296 is configured to contact a TACACS+
server during authentication:
login: test
Password:
Contacting TACACS+ server. Please wait.
3-3
AI296 Version 9.8x User’s Guide
AI296 Local Menu System: Logging Into AI296
The following message appears when AI296 is configured to contact a TACACS+
server during authentication, but the contact attempt fails:
login: test
Password:
Contacting TACACS+ server. Please wait.
TACACS+ server(s) not responding.
ꢀ
Note: Five consecutive failed login attempts generate an SNMP trap and a log
message saying that the login failed. Also, an entry appears in the log file with
text stating Warning: xconsecutive failed login attemptswhere xis the number
of consecutive failed login attempts.
Using an Asynchronous Port for Login
Two tools are required for logging into AI296 using an asynchronous port:
z
A PC with terminal emulation software such as HyperTerminal (included with
Windows 95/98/2000/XP) or ProComm.
z
Terminal cable with these specifications: null (RS232) cable with DB25 male
connector for AI296 distribution panel connection and appropriate connector for
your PC.
To log into AI296 using an asynchronous port:
1. Set the terminal emulation software to the following settings:
z
z
z
z
9600 baud
No parity
Eight data bits
One stop bit
2. Power on AI296.
3. Connect a PC to port 1 on the DP232 distribution panel.
ꢀ
Note: Link 1 on AI296 is enabled and configured for login by default, which
allows access through the link. AI296 may also be accessed through any
asynchronous link that is enabled and configured for login.
4. Press ENTER. The login prompt appears.
5. Enter your user ID. The password prompt appears.
6. Enter your password. The destination menu appears. You are now logged into
AI296.
3-4
AI296 Version 9.8x User’s Guide
AI296 Local Menu System: Logging Into AI296
The following message appears when AI296 is configured to contact a TACACS+
server during authentication:
login: test
Password:
Contacting TACACS+ server. Please wait.
The following message appears when AI296 is configured to contact a TACACS+
server during authentication, but the contact attempt fails:
login: test
Password:
Contacting TACACS+ server. Please wait.
TACACS+ server(s) not responding.
ꢀ
Note: Five consecutive failed login attempts generate an SNMP trap and a log
message saying that login failed. Also, a new entry will appear in the log
file with text stating Warning: x consecutive failed login attemptswhere xis
the number of consecutive failed login attempts.
3-5
AI296 Version 9.8x User’s Guide
AI296 Local Menu System: Accessing the Local Menu System
Accessing the Local Menu System
To access the AI296 menu session:
information.
2. At the destination menu, enter ai. The AI296 shell prompt appears.
3. Enter menu. The AI296 Main Menu appears.
AI296 Main Menu
+ Link Menu
+ Alias Menu
+ System Menu
+ Static Route Menu
....................................................................
:
:
: Select the desired menu option using the UP or DOWN arrow key. :
: Then press ENTER or RETURN to continue.
:..................................................................:
:
<F1> Help
<F4> Close
ꢀ
Note: The Alias Menu is only available when you log into AI296 in standalone mode.
3-6
AI296 Version 9.8x User’s Guide
AI296 Local Menu System: Navigating the Local Menu System
Navigating the Local Menu System
Arrow keys and keyboard short cuts can be used to navigate through the local menu
ꢀ
Note: To use the arrow keys in the menu system, make sure the VT100 arrow keys
are enabled in either your Telnet settings or your terminal emulation program.
Table 3-1 Direction Keys
Direction Keys
Up
Use the up arrow key or Press <Ctrl-p>
Use the down arrow key or Press <Ctrl-n>
Use the right arrow key or Press <Ctrl-f>
Use the left arrow key or Press <Ctrl-b>
Down
Right
Left
Identifying Types of Menu Items
The AI296 local menu system contains data items that let you input information or
toggle between available selections.
Data Entry Items
The following screen shot displays an example of a data entry menu item:
Link to configure . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
To enter information for a data entry menu item:
1. Move the cursor to the menu item.
ꢀ
Note: If the selected menu item has a range of valid values, that range will
appear in the bottom right of the screen.
2. Enter your data.
To erase existing data for a data entry menu item:
1. Move the cursor to the menu item.
2. Delete the data using BACKSPACE or DELETE and press ENTER.
OR
Enter new data.
3-7
AI296 Version 9.8x User’s Guide
AI296 Local Menu System: Navigating the Local Menu System
To save your changes:
z
z
Press F2 (or use the up and down arrow keys to highlight [Send]) and ENTER.
Enter yto save. If an error message appears, check your work and make changes
as necessary.
z
Press CTRL-E to save data entries immediately without being queried to save. If
an error message appears, check your work and make changes as necessary.
Toggle Items
The following screen shot displays an example of a toggle menu item. The selected
option has brackets around it.
Link state . . . . . . . . . . . . . . . . . . . . . . . . . .
[Up]
Down
To select a value for a toggle menu item:
1. Move the cursor to the menu item.
2. Highlight the option you want to select and press ENTER. The brackets move to
that option.
To save your changes:
z
z
Press F2 (or use the up and down arrow keys to highlight [Send]) and ENTER.
Enter yto save. If an error message appears, check your work and make changes
as necessary.
z
Press CTRL-E to save data entries immediately without being queried to save. If
an error message appears, check your work and make changes as necessary.
3-8
AI296 Version 9.8x User’s Guide
AI296 Local Menu System: Accessing the Help Menu
Accessing the Help Menu
The AI296 help menu lists all available keyboard codes and function keys with their
associated purposes. The help menu can be accessed by doing one of the following
things:
z
z
z
Pressing F1 and ENTER
Selecting Help on the menu and ENTER
Pressing ESC-1 and ENTER.
The following example displays the first page of the local menu system help screen:
Navigation Help
Page 1 of 4
This screen displays when you press the <F1> key or if you enter an invalid key-
stroke from the Main Menu. The following keyboard function keys are programmed
to allow you to enter or change data in menus:
<F1>; <F2>; <F4>; UP Arrow; DOWN Arrow; LEFT Arrow; RIGHT Arrow
If you can not locate these keys on your keyboard, use the following keyboard
equivalent codes to provide the same functionality:
Keyboard Code Function Key
Purpose
Esc 1
Esc 2
<F1>
<F2>
HELP - displays this help screen from any menu.
SEND - transmits the currently displayed data. You
are given a confirmation prompt before the actual
transmittal of data occurs. When you press the <F2>
key, the RIGHT and LEFT arrow keys can then be used
to access the other commands.
Press SPACE BAR to continue, or 'q' to quit
3-9
AI296 Version 9.8x User’s Guide
AI296 Local Menu System: Exiting the Local Menu System
Exiting the Local Menu System
To exit the local menu system and save all changes:
1. Select <F2> Send and press ENTER.
The following prompt appears:
Save changes? (y/n)
2. Save the changes:
y
3. Select <F4> Close and press ENTER until you are out of the menu system.
ꢀ
Note: Entering <CTRL> + Rtakes you directly to the main menu.
3-10
4
System Configuration
This chapter provides information on configuring AI296 system settings with the AI198 menu
system and the AI296 local menu system. To configure AI296 with the AI198 menu system, the
AI198 software must be at version 1.90 or later. The AI198 menu system settings take effect only
when AI296 is operating in switch mode (non-standalone mode).
Guide to this Chapter
4-1
AI296 Version 9.8x User’s Guide
System Configuration: General System Properties Configuration
General System Properties Configuration
General system properties are configurable at the first level of the AI198 and AI296
System menu. The following menu items can be configured:
z
z
z
z
z
z
z
z
Destination Menu Break Sequence
Description
This menu item sets the character sequence that lets the user exit a connection from
the destination menu.
Format
Destination menu break sequences take the following format:
attention_keystroke [ delay_start, delay_end ] next_character
attention_keystroke
Defines the keystroke that indicates that a break
sequence is coming. Valid values are:
z <x>where xrepresents the decimal ASCII value
of the keystroke. For example, enter <9>to
represent the TAB key.
z <c>xwhere <c>represents the CTRL key and x
represents the actual key name. For example,
enter <c>^to represent CTRL+SHIFT+6.
z <c><x>where <c>represents the CTRL key and x
represents the decimal ASCII value of the actual
key name. For example, enter <c><9>to represent
CTRL+TAB.
delay_start
Defines the amount of time (in seconds) you must wait
before entering the next character. Valid values are
integers from 0 to 8.
4-2
AI296 Version 9.8x User’s Guide
System Configuration: General System Properties Configuration
delay_end
Defines the amount of time (in seconds) before which
you must enter the next character. Valid values are
integers from 1 to 9.
ꢀ
Note: If you do not enter the next character within the
configured time frame, then both the
attention_keystrokeand next_character
values are treated as data and forwarded.
next_character
Defines the next character in the sequence. Valid
values are:
z <x>where xrepresents the decimal ASCII value
of the keystroke. For example, enter <9>to
represent the TAB key.
z <c>xwhere <c>represents the CTRL key and x
represents the actual key name. For example,
enter <c>^to represent CTRL+SHIFT+6.
z <c><x>where <c>represents the CTRL key and x
represents the decimal ASCII value of the actual
key name. For example, enter <c><9>to represent
CTRL+TAB.
ꢀ
Note: You can include multiple characters with delays between each in the break
sequence. For example, <c>^[1,5]x[0,9]k is a valid entry.
Menu Item Type
Data
Configuration in the AI198 Menu System
1. Access Menu 4.2.11 pg 2.
2. From Menu 4.2.11 pg 2, enter 3,and the desired destination menu break
sequence. The maximum length is 44 characters. The default is <c>^[1,5]x.
This example displays item 03 Destination Menu Break Sequence configured as
<c>^[2,6]x.
>3,<c>^[2,6]x
Menu 4.2.11 pg 2
01*10 Base T Ethernet-------------------------------------------------------OFF
02+Radius Configuration Menu
03 Destination Menu Break Sequence-----------------------------------<c>^[2,6]x
4-3
AI296 Version 9.8x User’s Guide
System Configuration: General System Properties Configuration
Configuration in the AI296 Local Menu System
1. Access the System Menu.
2. Enter a character sequence for Destination Menu Break Sequence. Maximum length
is 44 characters. The default is <c>^[1,5]x.
The following example displays item Destination Menu Break Sequence set to <c><33>.
System Menu
System Prompt . . . ................................................. [232]
Destination Menu Break Sequence . . . . . . . ..................... <c><33>
Ethernet Port Settings
Description
The Ethernet port settings are configured using two menu items:
z 10BaseT Ethernet—Enables or disables the 10BaseT Ethernet port on the front
panel of AI296.
z Dual Ethernet—Enables or disables simultaneous operation of the faceplate
mounted 10BaseT Ethernet port and the IRB.
ꢀ
Note: When the dual Ethernet setting is enabled, the 10BaseT Ethernet setting
has no effect on AI296 operation.
Menu Item Type
Toggle for both menu items
Configuration in the AI198 Menu System
1. Access Menu 4.2.11 pg 2.
2. For 01*10 Base T Ethernet, enter 1to select OFF or ON. The default is OFF.
3. For 07*Dual Ethernet, enter 7to select OFF or ON. The default is OFF.
This example displays 01*10 Base T Ethernet set to ON and 07*Dual Ethernet set to OFF.
>7
Menu 4.2.11 pg 2
01*10 Base T Ethernet------------------------------------------------------- ON
02+Radius Configuration Menu
03 Destination Menu Break Sequence-----------------------------------<c>^[1,5]x
04+TACACS Configuration Menu
05 TCP Outgoing Connection Timer (2-360s)-----------------------------------075
07*Dual Ethernet (On, Off)--------------------------------------------------OFF
4-4
AI296 Version 9.8x User’s Guide
System Configuration: General System Properties Configuration
Configuration in the AI296 Local Menu System
1. Access the System Menu.
2. For 10 Base T Ethernet, select Off or On. The default is off when running in switch
mode. The default is on when running in standalone mode.
3. For Dual Ethernet, select Off or On. The default is Off.
This example displays 10 Base T Ethernet set to ON and Dual Ethernet set to OFF.
System Menu
System Prompt . . . ................................................. [232]
Destination Menu Break Sequence . . . . . . . ..................... <c><33>
TCP Default Window Size . . . . . . . . . .
TCP Send Ahead . . . . . . . . . . . . . . . . . . . . . . .
[200]
512
1024
On
2048
[Off]
Telnet Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... 23
FTP Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... 21
10 Base T Ethernet . . . . . . . . . . . . . . . . . . . . .
Dual Ethernet . . . . . . . . . . . . . . . . . . . . . . .
Off
[Off]
[On]
On
FTP Port
Description
This menu item sets the FTP server port number.
Menu Item Type
Data
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.
2. For 16 FTP port number, enter 16,and the FTP server port number. Valid values are
1 to 65534. The default is 21.
4-5
AI296 Version 9.8x User’s Guide
System Configuration: General System Properties Configuration
This example displays 16 FTP port number set to 220.
>16,220
Menu 4.2.11 pg 1
01 IP Address (0.0.0.0 - 255.255.255.254)-----------------------010.040.057.015
02 IP Address Range (1 - 255)-----------------------------------------------001
03 IP Subnet Mask (0.0.0.1 - 255.255.255.254) ------------------255.255.000.000
04 Primary IP Router Address (0.0.0.0 - 255.255.255.254) -------010.040.000.001
05 Secondary IP Router Address (0.0.0.0 - 255.255.255.254) -----000.000.000.000
06*TCP Default Window Size (200, 512, 1024, 2048)-------------------------- 200
07*TCP Send Ahead-----------------------------------------------------------OFF
08+SNMP System Parameters
09*Bring passive link down when all calls have cleared----------------------OFF
10 Passive link Stay Inactive timer--------------------------------------000060
11 Passive link Standby Mode timer---------------------------------------000025
12+Link Setup
13+IP Over X.25 Subnets
14+IP Static Routes
15 Telnet port number (1..65534)------------------------------------------00023
16 FTP port number (1..65534)---------------------------------------------00220
Configuration in the AI296 Local Menu System
1. Access the System Menu.
2. For FTP Port, enter the desired FTP port value. Valid values are from 0 to 65534.
This example displays FTP Port set to 1752.
System Menu
System Prompt . . . ................................................. [232]
Destination Menu Break Sequence . . . . . . . ..................... <c><33>
TCP Default Window Size . . . . . . . . . .
[200]
512
1024
On
2048
[Off]
TCP Send Ahead . . . . . . . . . . . . . . . . . . . . . . .
Telnet Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... 23
FTP Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1752
IP Settings
Description
The IP settings are configurable using five menu items in the CLC menu or via a shell
command on AI296. The configurable values are:
z
z
z
z
z
IP address
IP address range
IP subnet mask
Primary IP router address
Secondary IP router address.
4-6
AI296 Version 9.8x User’s Guide
System Configuration: General System Properties Configuration
Menu Item Types
Data
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.
2. For 01 IP Address, enter 1,and the IP address for AI296. The default is
000.000.000.000.
3. For 02 IP Address Range, enter 2,and the number of the IP addresses to be
assigned to AI296. The valid range is 1 to 255.
4. For 03 IP Subnet Mask, enter 3,and the IP subnet mask for AI296. The default is
255.255.255.254.
5. For 04 Primary IP Router Address, enter 4,and the IP address of the primary router
for AI296. The default is 000.000.000.000.
6. For 05 Secondary IP Router Address, enter 5,and the IP address of the secondary
router for AI296. The default is 000.000.000.000.
This example displays:
z 01 IP Address set to 10.38.49.12
z 02 IP Address Range set to 3
z 03 IP Subnet Mask set to 255.255.000.000
z 04 Primary IP Router Address set to 010.038.000.001
z 05 IP Router Address set to 010.038.000.002
>5,10.38.0.2
Menu 4.2.11 pg 1
01 IP Address (0.0.0.0 - 255.255.255.254)-----------------------010.038.049.012
02 IP Address Range (1 - 255)-----------------------------------------------003
03 IP Subnet Mask (0.0.0.1 - 255.255.255.254) ------------------255.255.000.000
04 Primary IP Router Address (0.0.0.0 - 255.255.255.254) -------010.038.000.001
05 Secondary IP Router Address (0.0.0.0 - 255.255.255.254) -----010.038.000.002
ꢀ
Note: For information about configuring IP setting with shell commands, refer to
4-7
AI296 Version 9.8x User’s Guide
System Configuration: General System Properties Configuration
Passive Link Settings
Description
The passive link settings are configured using three menu items. The configurable
values are:
z Passive link down state—Configures standby (DMlock) mode for a passive link.
When this feature is turned on, a passive link will go into DMlock mode after all
calls have cleared. When turned off, a passive link will stay up when all calls have
cleared.
z Passive link stay inactive timer—Sets the number of seconds a passive link waits
for a connection to come up before failing.
z Passive link standby mode timer—Configures the amount of time a link remains in
standby mode before it becomes idle. Immediately after a passive link becomes
inactive, it goes into the standby (DMlock) mode.
Menu Item Types
Toggle for the passive link down state
Data for the passive link stay inactive timer and the passive link standby mode timer
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.
2. For 09*Bring passive link down when all calls have cleared, enter 9to select ON or
OFF. The default is OFF.
3. For 10 Passive link Stay Inactive timer, enter 10,and a value in seconds for the
passive link stay inactive timer. The minimum value is 25 seconds and the default
is 60 seconds.
4. For 11 Passive link Standby Mode timer, enter 11,and a value in seconds for the
passive link standby mode timer. The minimum value is 5seconds and the default
is 25 seconds.
4-8
AI296 Version 9.8x User’s Guide
System Configuration: General System Properties Configuration
This example displays:
z 09*Bring passive link down when all calls have cleared set to ON
z 10 Passive link Stay Inactive timer set to 50
z 11 Passive link Standby Mode timer set to 20
>11,20
Menu 4.2.11 pg 1
01 IP Address (0.0.0.0 - 255.255.255.254)-----------------------010.040.057.015
02 IP Address Range (1 - 255)-----------------------------------------------001
03 IP Subnet Mask (0.0.0.1 - 255.255.255.254) ------------------255.255.000.000
04 Primary IP Router Address (0.0.0.0 - 255.255.255.254) -------010.040.000.001
05 Secondary IP Router Address (0.0.0.0 - 255.255.255.254) -----000.000.000.000
06*TCP Default Window Size (200, 512, 1024, 2048)-------------------------- 200
07*TCP Send Ahead-----------------------------------------------------------OFF
08+SNMP System Parameters
09*Bring passive link down when all calls have cleared---------------------- ON
10 Passive link Stay Inactive timer--------------------------------------000050
11 Passive link Standby Mode timer---------------------------------------000020
Configuration in the AI296 Local Menu System
1. Access the System Menu.
2. For Bring passive links down when all calls have cleared, select Yes or No. The
default is No.
3. For Time to remain inactive after being brought down, enter a value in seconds.
The minimum value is 25 seconds and the default is 60 seconds.
4. For Time to stand by before being brought up, enter a value in seconds. The
minimum value is 5 seconds and the default is 25 seconds.
This example displays:
z Bring passive links down when all calls have cleared set to Yes
z Time to remain inactive after being brought down set to 50
z Time to stand by before being brought up set to 20.
System Menu
System Prompt . . . ................................................. [296]
Destination Menu Break Sequence . . . . . . . .................. <c>^[1,5]x
TCP Default Window Size . . . . . . . . . .
[200]
512 1024 2048
Enabled [Disabled]
TCP Send Ahead . . . . . . . . . . . . . . . . . .
Telnet Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 23
FTP Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 21
10 Base T Ethernet . . . . . . . . . . . . . . . . . . . . .
Dual Ethernet . . . . . . . . . . . . . . . . . . . . . . .
Bring passive links down when all calls have cleared . . . .
[Off]
[Off]
[Yes]
On
On
No
Time to remain inactive after being brought down (sec) . . . . . . . .... 50
Time to stand by before being brought up (sec) . . . . . . . . . . . .... 20
4-9
AI296 Version 9.8x User’s Guide
System Configuration: General System Properties Configuration
System Prompt
Description
This item sets the system prompt value in the CLI.
Menu Item Type
Data
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.
2. For 17 Prompt String, enter 17,and the desired system prompt value. There is no
default prompt string. The maximum length is 64 characters.
This example displays item 17 Prompt String set to NewPrompt.
>17,NewPrompt
Menu 4.2.11 pg 1
01 IP Address (0.0.0.0 - 255.255.255.254)-----------------------010.040.057.015
02 IP Address Range (1 - 255)-----------------------------------------------001
03 IP Subnet Mask (0.0.0.1 - 255.255.255.254) ------------------255.255.000.000
04 Primary IP Router Address (0.0.0.0 - 255.255.255.254) -------010.040.000.001
05 Secondary IP Router Address (0.0.0.0 - 255.255.255.254) -----000.000.000.000
06*TCP Default Window Size (200, 512, 1024, 2048)-------------------------- 200
07*TCP Send Ahead-----------------------------------------------------------OFF
08+SNMP System Parameters
09*Bring passive link down when all calls have cleared---------------------- ON
10 Passive link Stay Inactive timer--------------------------------------000050
11 Passive link Standby Mode timer---------------------------------------000020
12+Link Setup
13+IP Over X.25 Subnets
14+IP Static Routes
15 Telnet port number (1..65534)------------------------------------------00023
16 FTP port number (1..65534)---------------------------------------------00021
17 Prompt String------------------------------------------------------NewPrompt
Configuration in the AI296 Local Menu System
1. Access the System Menu.
2. For System Prompt, enter the desired system prompt.
This example displays System Prompt set to NewPrompt.
System Menu
System Prompt . . . ............................................. NewPrompt
4-10
AI296 Version 9.8x User’s Guide
System Configuration: General System Properties Configuration
TCP Settings
Description
The TCP settings are configured using two menu items. The configurable values are:
z TCP default window size—Sets the TCP default window size for AI296. The window
size specifies how many bytes AI296 will send to another device or how many
bytes another device may send to the AI296 before receiving an
acknowledgement.
ꢀ
Note: A small default window size way slow transfers to and from AI296.
z TCP send ahead—Enables or disables AI296’s ability to send a TCP window without
requiring an acknowledgment. When enabled, acknowledgment is not required.
When disabled, acknowledgment is required.
Menu Item Type
Toggle
Configuration in the AI198 Menu System
1. Access System Menu 4.2.11.
2. For 06*TCP Default Window Size, enter 6to select 200, 512, 1024, or 2048. The default
is 200.
3. For 07*TCP Send Ahead, enter 7to select OFF or ON. The default is OFF.
This example displays 06*TCP Default Window Size set to 1024 and 07*TCP Send Ahead set
to ON.
>7
Menu 4.2.11 pg 1
01 IP Address (0.0.0.0 - 255.255.255.254)-----------------------010.040.057.015
02 IP Address Range (1 - 255)-----------------------------------------------001
03 IP Subnet Mask (0.0.0.1 - 255.255.255.254) ------------------255.255.000.000
04 Primary IP Router Address (0.0.0.0 - 255.255.255.254) -------010.040.000.001
05 Secondary IP Router Address (0.0.0.0 - 255.255.255.254) -----000.000.000.000
06*TCP Default Window Size (200, 512, 1024, 2048)--------------------------1024
07*TCP Send Ahead----------------------------------------------------------- ON
Configuration in the AI296 Local Menu System
1. Access the System Menu.
2. For TCP Default Window Size, select 200, 512, 1024, or 2048. The default is 200.
3. For TCP Send Ahead, select Enabled or Disabled. The default is Disabled.
4-11
AI296 Version 9.8x User’s Guide
System Configuration: General System Properties Configuration
This example displays TCP Default Window Size set to 1024 and TCP Send Ahead set to
Enabled.
System Menu
System Prompt . . . ............................................. NewPrompt
Destination Menu Break Sequence . . . . . . . .................. <c>^[1,5]x
TCP Default Window Size . . . . . . . . . .
200
512
[Enabled]
[1024]
2048
Disabled
TCP Send Ahead . . . . . . . . . . . . . . . . . .
Telnet Port
Description
This item sets the Telnet port value for AI296.
Menu Item Type
Data
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.
2. For 15 Telnet port number, enter 15,and the desired port number value. Valid
values are 1 to 65534. The default is 23.
This example displays 15 Telnet port number set to 122.
>15,122
Menu 4.2.11 pg 1
01 IP Address (0.0.0.0 - 255.255.255.254)-----------------------010.040.057.015
02 IP Address Range (1 - 255)-----------------------------------------------001
03 IP Subnet Mask (0.0.0.1 - 255.255.255.254) ------------------255.255.000.000
04 Primary IP Router Address (0.0.0.0 - 255.255.255.254) -------010.040.000.001
05 Secondary IP Router Address (0.0.0.0 - 255.255.255.254) -----000.000.000.000
06*TCP Default Window Size (200, 512, 1024, 2048)--------------------------1024
07*TCP Send Ahead----------------------------------------------------------- ON
08+SNMP System Parameters
09*Bring passive link down when all calls have cleared---------------------- ON
10 Passive link Stay Inactive timer--------------------------------------000050
11 Passive link Standby Mode timer---------------------------------------000020
12+Link Setup
13+IP Over X.25 Subnets
14+IP Static Routes
15 Telnet port number (1..65534)------------------------------------------00122
Configuration in the AI296 Local Menu System
1. Access the System Menu.
2. For Telnet Port, enter the desired value. The default is 23.
4-12
AI296 Version 9.8x User’s Guide
System Configuration: General System Properties Configuration
This example displays Telnet Port set to 55.
System Menu
System Prompt . . . ............................................. NewPrompt
Destination Menu Break Sequence . . . . . . . .................. <c>^[1,5]x
TCP Default Window Size . . . . . . . . . .
TCP Send Ahead . . . . . . . . . . . . . . . . . .
Telnet Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 55
200
512
[Enabled]
[1024]
2048
Disabled
4-13
AI296 Version 9.8x User’s Guide
System Configuration: RADIUS Configuration
RADIUS Configuration
RADIUS authentication verifies user login information against valid user information in
a database on a centralized RADIUS authentication server. A primary and secondary
RADIUS server are configurable to provide secure access for an entire AI296
network. AI296 RADIUS authentication is available for Telnet, asynchronous, and
synchronous ports. The following menu items can be configured for RADIUS:
z
z
Server Settings
Description
The RADIUS server settings are configured using four menu items for the primary and
secondary server. The configurable values are:
z Primary/secondary server status—Enables or disables the primary or secondary
server.
z Primary/secondary server IP address—Defines an IP address for the primary or
secondary server.
z Primary/secondary server port—Defines the port number for the primary or
secondary server.
z Primary/secondary server secret—Defines a password for the primary or secondary
server.
Menu Item Types
Toggle for primary/secondary server status
Data for primary/secondary server IP address, server port, and server secret
Configuration in the AI198 Menu System
ꢀ
Note: RADIUS and TACACS+ cannot both be configured at the same time.
Attempting to do this generates an error.
To configure the RADIUS server settings:
1. Access Menu 4.2.11-2.2.
2. For 01*Primary Server Status, enter 1to select ENABLED or DISABLED. The default is
DISABLED.
3. For 02 Primary Server IP Address, enter 2,and the desired IP address. The default
is 0.0.0.0.
4-14
AI296 Version 9.8x User’s Guide
System Configuration: RADIUS Configuration
4. For 03 Primary Server Port, enter 3,and the desired port number. The default is
1812.
5. For 04 Primary Server Secret, enter 4,and the desired password. The default is
applied.
6. If desired, repeat steps 2 through 5 for the secondary server settings.
This example displays:
z 01*Primary Server Status set to ENABLED
z 02 Primary Server IP Address set to 050.023.156.012
z 03 Primary Server Port set to 122
z 04 Primary Server Secret set to hilltop.
>4,hilltop
Menu 4.2.11-2.2
01*Primary Server Status (Enabled, Disabled)--------------------------- ENABLED
02 Primary Server IP Address------------------------------------050.023.156.012
03 Primary Server Port (1..65535)-----------------------------------------00122
04 Primary Server Secret-------------------------------
hilltop
Configuration in the AI296 Local Menu System
1. Access the RAS Configuration Menu located under the System Menu.
2. For RADIUS Primary Server Status, select Enabled or Disabled.
3. For IP address, enter an IP address. The default is 0.0.0.0.
4. For Port Number, enter a port number. The default is 1812 for RADIUS servers.
5. For Secret, enter a password. The default is applied.
6. Repeat steps 2 through 5 for the secondary RADIUS server.
This example displays:
z RADIUS Primary Server Status set to Enabled
z IP Address set to 12.33.57.2
z Port Number set to 122
z Secret set to newone.
RAS Configuration Menu
RADIUS Primary Server Status . . . . . . . . . . . [Enabled] Disabled
IP Address . . . . .... 12.33.57.2 Port Number . . . . . 122
Secret . . . .............. newone
4-15
AI296 Version 9.8x User’s Guide
System Configuration: RADIUS Configuration
Shell/FTP Options
Description
This item sets the Shell/FTP option for RADIUS as one of the following:
z Enabled—Enables RADIUS login.
z Disabled—Disables RADIUS login.
z Local fallback—Enables RADIUS login, but resorts to local login if the RADIUS
login fails.
ꢀ
Note: RADIUS and TACACS+ cannot both be configured at the same time.
Attempting to do this generates an error.
Menu Item Type
Toggle
Configuration in the AI198 Menu System
To configure the shell/FTP RADIUS option:
1. Access Menu 4.2.11-2.2.
2. For 09*Shell/FTP Radius Option, enter 9to select ENABLED, DISABLED, or LOCAL
FALLBACK. The default is DISABLED.
This example displays 09*Shell/FTP Radius Option set to LOCAL FALLBACK.
>9
Menu 4.2.11-2.2
01*Primary Server Status (Enabled, Disabled)--------------------------- ENABLED
02 Primary Server IP Address------------------------------------050.023.156.012
03 Primary Server Port (1..65535)-----------------------------------------00122
04 Primary Server Secret-------------------------------
hilltop
05*Secondary Server Status (Enabled, Disabled)-------------------------DISABLED
06 Secondary Server IP Address----------------------------------000.000.000.000
07 Secondary Server Port (1..65535)---------------------------------------01812
08 Secondary Server Secret----------------------------- applied
09*Shell/FTP Radius Option (Enabled, Disabled, Local Fallback)---LOCAL FALLBACK
Configuration in the AI296 Local Menu System
To configure the shell/FTP RADIUS option:
1. Access the RAS Configuration Menu located under the System Menu.
2. For Shell RAS Option, select Disabled, RADIUS, RADIUS/Fallback. The default is
Disabled.
4-16
AI296 Version 9.8x User’s Guide
System Configuration: RADIUS Configuration
This example displays the shell RAS option set to RADIUS/Fallback.
RAS Configuration Menu
RADIUS Primary Server Status . . . . . . . . . . . [Enabled] Disabled
IP Address . . . . ....... 0.0.0.0 Port Number . . . . 1812
Secret . . . .............. newone
RADIUS Secondary Server Status . . . . . . . . . . Enabled [Disabled]
IP Address . . . . ....... 0.0.0.0 Port Number . . . . 1812
Secret . . . ............. applied
Shell RAS Option:
Disabled
RADIUS
[RADIUS/Fallback]
4-17
AI296 Version 9.8x User’s Guide
System Configuration: TACACS+ Configuration
TACACS+ Configuration
TACACS+ authentication verifies user login information against the user’s permission
level on a TACACS+ server. Up to 9 TACACS+ servers are configurable to provide
secure access for an entire AI296 network. AI296 TACACS+ authentication is
available for Telnet, asynchronous, asynchronous PPP, and FTP connections. The
following menu items can be configured for TACACS+ on the AI198 menu system:
z
z
ꢀ
Note: TACACS+ is not configurable from the AI296 local menu system. For
information on configuring TACACS+ when logged into AI296, refer to shell
9-99.
Server Settings
Description
From the AI198 Menu System, the TACACS+ server settings are configured using
four menu items for the primary and secondary server. The configurable values are:
z Primary/secondary server status—Enables or disables the primary or secondary
server.
z Primary/secondary server IP address—Defines an IP address for the primary or
secondary server.
z Primary/secondary server port—Defines the port number for the primary or
secondary server.
z Primary/secondary server secret—Defines a password for the primary or secondary
server.
Menu Item Types
Toggle for primary/secondary server status
Data for primary/secondary server IP address, server port, and server secret
Configuration in the AI198 Menu System
To configure the TACACS+ server settings:
1. Access Menu 4.2.11-2.4.
2. For 01*Primary Server Status, enter 1to select ENABLED or DISABLED. The default is
DISABLED.
4-18
AI296 Version 9.8x User’s Guide
System Configuration: TACACS+ Configuration
3. For 02 Primary Server IP Address, enter 2,and the IP address. The default is
0.0.0.0.
4. For 03 Primary Server Port, enter 3,and the port number. The default is 49.
5. For 04 Primary Server Secret, enter 4,and the password. The default is applied.
6. Repeat steps 2 through 5 for the secondary server settings.
This example displays:
z 01*Primary Server Status set to ENABLED
z 02 Primary Server IP Address set to 050.023.156.011
z 03 Primary Server Port set to 122
z 04 Primary Server Secret set to hilltop.
>4,hilltop
Menu 4.2.11-2.4
01*Primary Server Status (Enabled, Disabled)--------------------------- ENABLED
02 Primary Server IP Address------------------------------------050.023.156.012
03 Primary Server Port (1..65535)-----------------------------------------00122
04 Primary Server Secret-------------------------------
hilltop
Shell/FTP Options
Description
This item sets the Shell/FTP option for TACACS+ as one of the following:
z Enabled—Enables TACACS+ login.
z Disabled—Disables TACACS+ login.
z Local fallback—Enables TACACS+ login, but resorts to local login if the
TACACS+ login fails.
ꢀ
Note: RADIUS and TACACS+ cannot both be configured at the same time.
Attempting to do this generates an error.
Menu Item Type
Toggle
Configuration in the AI198 Menu System
Important: Configuration of the shell/FTP TACACS+ option results in privilege level
authorization and supersedes any TACACS+ configuration on the AI296
card.
To configure the shell/FTP TACACS+ option:
1. Access Menu 4.2.11-2.4.
4-19
AI296 Version 9.8x User’s Guide
System Configuration: TACACS+ Configuration
2. For 09*Shell/FTP TACACS Option, enter 9to select ENABLED, DISABLED, or LOCAL
FALLBACK. The default is DISABLED.
This example displays 09*Shell/FTP TACACS Option set to LOCAL FALLBACK.
>9
Menu 4.2.11-2.4
01*Primary Server Status (Enabled, Disabled)---------------------------DISABLED
02 Primary Server IP Address------------------------------------000.000.000.000
03 Primary Server Port (1..65535)-----------------------------------------00049
04 Primary Server Secret-------------------------------
applied
05*Secondary Server Status (Enabled, Disabled)-------------------------DISABLED
06 Secondary Server IP Address----------------------------------000.000.000.000
07 Secondary Server Port (1..65535)---------------------------------------00049
08 Secondary Server Secret----------------------------- applied
09*Shell/FTP TACACS Option (Enabled, Disabled, Local Fallback)---LOCAL FALLBACK
4-20
AI296 Version 9.8x User’s Guide
System Configuration: SNMP Configuration
SNMP Configuration
This section discusses SNMP configuration options. The following configuration
components are available:
z
z
z
z
z
Authentication Traps
Description
This item enables or disables the generation of authentication failure traps by AI296.
When a user enters faulty login information, authentication traps are sent from an
SNMP agent to inform the management station about the incorrect login attempt.
Menu Item Types
Toggle
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.8.
2. For 04*Send authentication traps, enter 4to select ON or OFF. The default is ON.
The following example displays item 04*Send authentication traps set to ON.
>4
Menu 4.2.11.8
01 Contact person for this node------------------------------------------------
02 Node name-------------------------------------------------------------------
03 Node location---------------------------------------------------------------
04*Send authentication traps------------------------------------------------ ON
AI296 Local Menu Item Configuration
1. Access the SNMP Menu located under the System Menu.
2. For Send authentication traps, select On or Off. The default is ON.
4-21
AI296 Version 9.8x User’s Guide
System Configuration: SNMP Configuration
The following example displays the selection of On for menu item Send authentication
traps.
SNMP Menu
Contact person for this managed node . . . . . . . . . . . . .
Node name . . . . . . . . . . . . . . . . . . . . . . . . . . ...............
Node location . . . . . . . . . . . . . . . . . . . . . . . . ...............
Send authentication traps . . . . . . . . . . . . . . . . . .
[On]
Off
Community Names
Description
SNMP community names provide embedded password access to MIB contents.
There are three menu items available for configuring AI296 SNMP community name
information:
z Read Community Name—Sets the name that permits read only access to all objects in
the MIB.
z MIB2 Read Community Name—Sets the name that permits read only access to all
objects in MIB2.
z Write Community Name—Sets the name that permits read and write access to all
objects in the MIB.
Menu Item Types
Data for all menu items
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.8.
2. For 05 Read Community Name, enter 5,and the community name value. The
maximum length is 32 characters. The default value is readonly.
3. For 06 MIB2 Read Community Name, enter 6,and the community name value. The
maximum length is 32 characters. The default value is public.
4. For 07 Write Community Name, enter 7,and the community name value. The
maximum length is 32 characters. The default value is administrator.
4-22
AI296 Version 9.8x User’s Guide
System Configuration: SNMP Configuration
The following example displays:
z
z
z
Item 05 Read Community Name set to ReadComm.
Item 06 MIB2 Read Community Name set to MIB2.
Item 07 Write Community Name set to WriteComm.
>7,WriteComm
Menu 4.2.11.8
01 Contact person for this node------------------------------------------------
02 Node name-------------------------------------------------------------------
03 Node location---------------------------------------------------------------
04*Send authentication traps------------------------------------------------ ON
05 Read Community Name-------------------------------------------------ReadComm
06 MIB2 Read Community Name------------------------------------------------MIB2
07 Write Community Name-----------------------------------------------WriteComm
AI296 Local Menu Item Configuration
1. Access the SNMP Menu located under the System Menu.
2. For menu item Read Community Name, enter the community name value. The
maximum length is 32 characters. The default value is readonly.
3. For menu item MIB2 Read Community Name, enter the community name value. The
maximum length is 32 characters. The default value is public.
4. For menu item Write Community Name, enter the community name value. The
maximum length is 32 characters. The default value is administrator.
The following example displays:
z
z
z
Item Read Community Name set to ReadComm.
Item MIB2 Read Community Name set to MIB2.
Item Write Community Name set to WriteComm.
SNMP Menu
Contact person for this managed node . . . . . . . . . . . . .
Node name . . . . . . . . . . . . . . . . . . . . . . . . . . ...............
Node location . . . . . . . . . . . . . . . . . . . . . . . . ...............
Send authentication traps . . . . . . . . . . . . . . . . . .
[On]
Off
SNMP Manager #1 . . . . . . . . . . . . . . . . . . . . . . ..... 10.35.0.30
SNMP Manager #2 . . . . . . . . . . . . . . . . . . . . . . ..... 10.35.0.60
SNMP Manager #3 . . . . . . . . . . . . . . . . . . . . . . ..... 10.35.0.20
SNMP Manager #4 . . . . . . . . . . . . . . . . . . . . . . ........ 0.0.0.0
SNMP Manager #5 . . . . . . . . . . . . . . . . . . . . . . ........ 0.0.0.0
Read Community Name . . . . . . . . . . . . . . . . . . . . . ...... ReadComm
MIB2 Read Community Name . . . . . . . . . . . . . . . . . . ........... MIB2
Write Community Name . . . . . . . . . . . . . . . . . . . . ...... WriteComm
4-23
AI296 Version 9.8x User’s Guide
System Configuration: SNMP Configuration
Contact Persons
Description
This item defines the name of the person to contact regarding a specific node.
Menu Item Types
Data
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.8.
2. For 01 Contact person for this node, enter 1,and the desired contact person. The
maximum length is 40 characters.
The following example displays John Doe configured for menu item 01 Contact person
for this node:
>1,John Doe
Menu 4.2.11.8
01 Contact person for this node----------------------------------------John Doe
AI296 Local Menu Item Configuration
1. Access the SNMP Menu located under the System Menu.
2. For Contact person for this managed node, enter the contact person. The maximum
length is 40 characters.
The following example displays John Doe configured for menu item Contact person for
this managed node:
SNMP Menu
Contact person for this managed node . . . . . . . . . . . . ....... John Doe
Node Information
Description
There are two menu items available for configuring node information:
z Node Name—Defines the name of a location on a network.
z Node Location—Defines a location on a network.
Menu Item Types
Data
4-24
AI296 Version 9.8x User’s Guide
System Configuration: SNMP Configuration
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.8.
2. For 02 Node name, enter 2,and the node name. The maximum length is 40
characters.
3. For 03 Node location, enter 3,and a node location description. The maximum
length is 40 characters.
The following example displays the configuration of node name newNode and node
location Office B.
>3,Office B
Menu 4.2.11.8
01 Contact person for this node----------------------------------------John Doe
02 Node name------------------------------------------------------------newNode
03 Node location-------------------------------------------------------Office B
AI296 Local Menu Item Configuration
1. Access the SNMP Menu located under the System Menu.
2. For Node name, enter the node name. The maximum length is 40 characters.
3. For Node location, enter a node location description. The maximum length is 40
characters.
The following example displays the configuration of node name newNode and node
location Office B.
SNMP Menu
Contact person for this managed node . . . . . . . . . . . . ....... John Doe
Node name . . . . . . . . . . . . . . . . . . . . . . . . . . ....... newNode
Node location . . . . . . . . . . . . . . . . . . . . . . . . ...... Office B
SNMP Manager
Description
An SNMP manager is a combination of monitoring software running on a network
management station (NMS) and the actual device running the software. It collects and
acts on information from the various devices being monitored and/or controlled. The
SNMP manager also periodically polls the devices it is managing to get status
information. AI296 allows for the configuration of up to 5 SNMP managers.
ꢀ
Note: SNMP managers are only configurable when AI296 is in standalone mode.
They are not configurable through the AI198 menu system.
4-25
AI296 Version 9.8x User’s Guide
System Configuration: SNMP Configuration
Menu Item Types
Data
AI296 Local Menu Item Configuration
1. Access the SNMP Menu located under the System Menu.
2. For SNMP Manager #1, enter the IP address of the first SNMP manager. The default
is 0.0.0.0.
3. For SNMP Manager #2, enter the IP address of the second SNMP manager. The
default is 0.0.0.0.
4. For SNMP Manager #3, enter the IP address of the third SNMP manager. The default
is 0.0.0.0.
5. For SNMP Manager #4, enter the IP address of the fourth SNMP manager. The
default is 0.0.0.0.
6. For SNMP Manager #5, enter the IP address of the fifth SNMP manager. The default
is 0.0.0.0.
The following example displays:
z SNMP Manager #1 set to 10.65.32.4
z SNMP Manager #2 set to 10.65.32.5
z SNMP Manager #3 set to 10.65.32.6
z SNMP Manager #4 set to 10.65.32.7
z SNMP Manager #5 set to 10.65.32.8
SNMP Menu
Contact person for this managed node . . . . . . . . . . . . .
Node name . . . . . . . . . . . . . . . . . . . . . . . . . . ...............
Node location . . . . . . . . . . . . . . . . . . . . . . . . ...............
Send authentication traps . . . . . . . . . . . . . . . . . .
[On]
Off
SNMP Manager #1 . . . . . . . . . . . . . . . . . . . . . . ..... 10.65.32.4
SNMP Manager #2 . . . . . . . . . . . . . . . . . . . . . . ..... 10.65.32.5
SNMP Manager #3 . . . . . . . . . . . . . . . . . . . . . . ..... 10.65.32.6
SNMP Manager #4 . . . . . . . . . . . . . . . . . . . . . . ..... 10.65.32.7
SNMP Manager #5 . . . . . . . . . . . . . . . . . . . . . . ..... 10.65.32.8
4-26
AI296 Version 9.8x User’s Guide
System Configuration: Static Route Configuration
Static Route Configuration
AI296 allows for the configuration of static routes using both the AI198 and AI296
menu systems.
IP Address Settings
Description
Static routes are configured with a destination and next hop IP address. The
destination IP address defines the static IP route you want to configure. The next hop
IP address defines the IP address of the router you want the system to use when
trying to reach the destination IP address.
Menu Item Types
Data
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.14.
2. From Menu 4.2.11.14, enter a value from 3to 11. Menu 4.2.11.14.1 appears.
3. For 01 Destination IP, enter an IP address value.
4. For 02 Next Hop IP, enter an IP address value.
The following example displays the configuration of destination address 84.238.45.2
and next hop address 23.51.93.5.
>2,023.051.093.005
Menu 4.2.11.14.1
01 Destination IP-----------------------------------------------084.238.045.002
02 Next Hop IP--------------------------------------------------023.051.093.005
AI296 Local Menu Item Configuration
1. Access the Static Route Menu.
2. Select [Add]. The IP Static Route Edit Menu appears.
3. For Destination IP Address, enter an IP address value. The default is 1.1.1.1.
4. For Next Hop IP Address, enter an IP address value. The default is 1.1.1.1.
The following example displays the configuration of destination IP address 12.240.54.3
and next hop IP address 12.240.54.4.
IP Static Route Edit Menu
Destination IP Address . . . . . . . . . . . . . . ........... 12.240.54.3
Next Hop IP Address . . . . . . . . . . . . . . . . ........... 12.240.54.4
4-27
AI296 Version 9.8x User’s Guide
System Configuration: TID to Modem Mux Configuration
TID to Modem Mux Configuration
The following are available:
z
z
z
z
Inactivity Timeout
Description
This menu item defines the amount of time (in seconds) the Modem Mux connection
must be inactive before it times out.
Menu Item Types
Data
Configuration in the AI198 Menu System
1. Access Menu 4.2.14-2.6.
2. From Menu 4.2.14-2.6, enter a value from 2to 11. Menu 4.2.14-2.6.1 appears.
3. For 06 Inactivity Timeout, enter 6,and a timeout value. Valid values are from 0 to
100000. The default is 300.
This example displays 06 Inactivity Timeout set to 1500.
>6,1500
Menu 4.2.14-2.6.1
01 TID to route--------------------------------------------
02*Port Data Bits (7, 8)------------------------------------------------------8
03*Port Stop Bits (1, 2)------------------------------------------------------1
04*Port Parity (None, Even, Odd)-------------------------------------------None
05 Init String-----------------------------------
06 Inactivity Timeout (0 - 100000)---------------------------------------001500
AI296 Local Menu Item Configuration
1. Access the TID to Modem Mux Menu located under the System Menu.
2. From the TID to Modem Mux Summary Menu, select [Add TID]. The TID To
Modem Mux Edit Menu appears.
3. For Inactivity Timeout, enter a timeout value. Valid values are from 0 to 100000.
The default is 300.
4-28
AI296 Version 9.8x User’s Guide
System Configuration: TID to Modem Mux Configuration
This example displays Inactivity Timeout set to 1500.
TID To Modem Mux Edit Menu
TID to route . . . . . . . . . . . . . . . . . . . . .....................
Port Data Bits . . . . . . . . . . . . . . . . . . . .
Port Stop Bits . . . . . . . . . . . . . . . . . . . . . .
Seven
[One]
Even
[Eight]
Two
Odd
Port Parity . . . . . . . . . . . . . . . . . . .
[None]
Init String . . . . . . . . . . . . . . . ...............................
Inactivity Timeout . . . . . . . . . . . . . . . . . . . . . . . .... 1500
Initialization String
Description
This menu item defines the string that is sent upon indication that there is a device
connected to the port (DSR asserted).
Menu Item Types
Data
Configuration in the AI198 Menu System
1. Access Menu 4.2.14-2.6.
2. From Menu 4.2.14-2.6, enter a value from 2to 11. Menu 4.2.14-2.6.1 appears.
3. For 05 Init String, enter 5,and an initialization string value. Maximum length is
30 characters.
This example displays 05 Init String set to conn23.
>5,conn23
Menu 4.2.14-2.6.1
01 TID to route--------------------------------------------
02*Port Data Bits (7, 8)------------------------------------------------------8
03*Port Stop Bits (1, 2)------------------------------------------------------1
04*Port Parity (None, Even, Odd)-------------------------------------------None
05 Init String-----------------------------------
conn23
AI296 Local Menu Item Configuration
1. Access the TID to Modem Mux Menu located under the System Menu.
2. From the TID to Modem Mux Summary Menu, select [Add TID]. The TID To
Modem Mux Edit Menu appears.
3. For Init String, enter a string value. Maximum length is 30 characters.
4-29
AI296 Version 9.8x User’s Guide
System Configuration: TID to Modem Mux Configuration
This example displays Init String set to conn23.
TID To Modem Mux Edit Menu
TID to route . . . . . . . . . . . . . . . . . . . . .....................
Port Data Bits . . . . . . . . . . . . . . . . . . . .
Port Stop Bits . . . . . . . . . . . . . . . . . . . . . .
Seven
[One]
Even
[Eight]
Two
Odd
Port Parity . . . . . . . . . . . . . . . . . . .
[None]
Init String . . . . . . . . . . . . . . . ........................ conn23
Port Bit Settings
Description
There are three menu items available for configuring TID to Modem Mux port bits:
z Port Data Bits—Defines the number of databits in a data byte.
z Port Stop Bits—Defines the number of stop bits for TID to Modem Mux. A stop bit
is an extra bit at the end of an asynchronous character that helps the receiver
recognize the end of the character.
z Port Parity—Defines parity, which is a process for detecting whether or not bits of
data have been altered during data transmission.
Menu Item Types
Toggle for all menu items
Configuration in the AI198 Menu System
1. Access Menu 4.2.14-2.6.
2. From Menu 4.2.14-2.6, enter a value from 2to 11. Menu 4.2.14-2.6.1 appears.
3. For 02*Port Data Bits, enter 2,to select 7 or 8. The default is 8.
4. For 03*Port Stop Bits, enter 3,to select 1 or 2. The default is 1.
5. For 04*Port Parity, enter 4,to select None, Even, or Odd. The default is None.
This example displays:
z 02*Port Data Bits set to 7
z 03*Port Stop Bits set to 1
z 04*Port Parity set to Even.
>4,Even
Menu 4.2.14-2.6.1
01 TID to route--------------------------------------------
02*Port Data Bits (7, 8)------------------------------------------------------7
03*Port Stop Bits (1, 2)------------------------------------------------------1
04*Port Parity (None, Even, Odd)-------------------------------------------Even
4-30
AI296 Version 9.8x User’s Guide
System Configuration: TID to Modem Mux Configuration
AI296 Local Menu Item Configuration
1. Access the TID to Modem Mux Menu located under the System Menu.
2. From the System Menu, select TID to Modem Mux. The TID to Modem Mux
Summary Menu appears.
3. From the TID to Modem Mux Summary Menu, select [Add TID]. The TID To
Modem Mux Edit Menu appears.
4. For Port Data Bits, select 7 or 8. The default is 8.
5. For Port Stop Bits, select 1 or 2. The default is 1.
6. For Port Parity, select None, Even, or Odd. The default is None.
This example displays:
z Port Data Bits set to 7
z Port Stop Bits set to 1
z Port Parity set to Even.
TID To Modem Mux Edit Menu
TID to route . . . . . . . . . . . . . . . . . . . . .....................
Port Data Bits . . . . . . . . . . . . . . . . . . . .
Port Stop Bits . . . . . . . . . . . . . . . . . . . . . .
[Seven]
[One]
[Even]
Eight
Two
Odd
Port Parity . . . . . . . . . . . . . . . . . . .
None
TID to Route
Description
This menu item defines the string that represents the TID to be routed to the Modem
Mux link.
Menu Item Type
Data
Configuration in the AI198 Menu System
1. Access Menu 4.2.14-2.6.
2. From Menu 4.2.14-2.6, enter a value from 2to 11. Menu 4.2.14-2.6.1 appears.
3. For 01 TID to route, enter 1,and the desired TID. Maximum length is 20
characters.
This example displays the TID configured as COLUMBUS-OH.
>1 columbus-oh
Menu 4.2.14-2.6.1
COLUMBUS-OH
01 TID to route--------------------------------------------
4-31
AI296 Version 9.8x User’s Guide
System Configuration: TID to Modem Mux Configuration
AI296 Local Menu Item Configuration
1. Access the TID to Modem Mux Menu located under the System Menu.
2. From the TID to Modem Mux Summary Menu, select [Add TID]. The TID To
Modem Mux Edit Menu appears.
3. For TID to route, enter the desired TID. Maximum length is 20 characters.
This example displays the TID configured as COLUMBUS-OH.
TID To Modem Mux Edit Menu
TID to route . . . . . . . . . . . . . . . . . . . . ......... COLUMBUS-OH
4-32
AI296 Version 9.8x User’s Guide
System Configuration: Time Configuration
Time Configuration
AI296 supports the Simple Network Time Protocol (SNTP). SNTP is a time protocol
that maintains a common time among Internet hosts.
ꢀ
Note: Time configuration options are only available when AI296 is operating in
standalone mode.
The following configuration items are available:
z
z
z
Daylight Savings Time
Description
There are eight menu items available for configuring Daylight Savings Time:
z Start On and End On—Configures the numbered day to start or end Daylight
Savings Time.
z Start Day and End Day—Configures the day of the week to start or end Daylight
Savings Time.
z Start Month and End Month—Configures the month to start or end Daylight Savings
Time.
z Start Hour and End Hour—Configures the hour of the day to start or end Daylight
Savings Time.
Menu Item Types
Toggle
AI296 Local Menu Item Configuration
1. Access the System Menu.
2. From the System Menu, select Time Menu. The Time Menu appears.
3. For Daylight Saving Time on this host is, select Enabled or Disabled.
4. For Start On, select the day number in the month that Daylight Savings Time will
start.
5. For Start Day, select the day that Daylight Savings Time will start.
6. For Start Month, select the month that Daylight Savings Time will start.
4-33
AI296 Version 9.8x User’s Guide
System Configuration: Time Configuration
7. For Start Hour, select the hour that Daylight Savings Time will start.
8. For End On, select the day number in the month that Daylight Savings Time will
end.
9. For End Day, select the day that Daylight Savings Time will end.
10. For End Month, select the month that Daylight Savings Time will end.
11. For End Hour, select the hour that Daylight Savings Time will end.
This following example displays:
z Daylight Saving Time on this host is set to Enabled
z Start On set to Second
z Start Day set to Sun
z Start month set to 3
z Start Hour set to 2
z End On set to First
z End Day set to Sun
z End month set to 11
z End Hour set to 2.
Time Menu
Current Time Zone (+/-hh:mm) . . . . . . . . . . . . . . . . . . . . . .+00:00
Daylight Saving Time on this host is . . . . . . . .
First
[Sun] Mon
[Enabled]
Third Fourth
Wed Thur
Disabled
Last
Start On . . . . . . . . .
Start Day . . . . . .
[Second]
Tue
Fri
Sat
Start Month (1-12, 1=Jan, 12=Dec) . . . . . . . . . . . . . . . . . . . 3
Start Hour (0-23) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
End On
End Day
. . . . . . . . .
. . . . . .
[First]
[Sun] Mon
Second
Tue
Third
Wed
Fourth
Thur Fri
. . . . . . . . . . . . . . . . . . . 11
Last
Sat
End Month (1-12, 1=Jan, 12=Dec)
End Hour (0-23) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
SNTP Settings
Description
SNTP is a time protocol that maintains a common time among Internet hosts. There
are 4 menu items available for configuring SNTP settings:
z SNTP client on this host is—Enables or disables SNTP. If Enabled is selected, the
system attempts to contact the primary and secondary SNTP servers for the exact
time. If AI296 is unable to contact either the primary or secondary SNTP server, it
uses the local time maintained by AI296. If Disabled is selected, the system uses
the local time maintained by AI296.
4-34
AI296 Version 9.8x User’s Guide
System Configuration: Time Configuration
z Primary SNTP Server—Defines the IP address of the first SNTP server from which
AI296 will attempt to retrieve the exact time.
z Secondary SNTP Server—Defines the IP address of the second SNTP server from
which AI296 will attempt to retrieve the exact time.
ꢀ
Note: The SNTP client must be enabled before the primary or secondary SNTP
server can be defined.
z SNTP Poll Interval (minutes)—Defines the time interval (in minutes) for AI296 to
poll the SNTP servers.
Menu Item Types
Toggle for SNTP client on this host is
Data for Primary SNTP Server, Secondary SNTP Server, and SNTP Poll Interval (minutes)
settings
AI296 Local Menu Item Configuration
1. Access the Time Menu located under the System Menu.
2. For SNTP client on this host is, select Enabled or Disabled. The default is Enabled.
3. For Primary SNTP Server, enter the primary server IP address. The default is
0.0.0.0.
4. For Secondary SNTP Server, enter the secondary server IP address. The default is
0.0.0.0.
5. For SNTP Poll Interval (minutes), enter the time in minutes for the SNTP servers to
be polled. The default is 10.
This following example displays:
z SNTP client on this host is set to Enabled
z Primary SNTP Server set to 12.43.167.59
z Secondary SNTP Server set to 12.43.167.60
z SNTP Poll Interval (minutes) set to 7.
Time Menu
Current Time Zone (+/-hh:mm) . . . . . . . . . . . . . . . . . . . . . .+00:00
Daylight Saving Time on this host is . . . . . . . .
[Enabled]
Disabled
SNTP client on this host is . . . . . . . . . . . . .
[Enabled]
Disabled
Primary SNTP Server . . . . . . . . . . . . . . . . . . . . . ... 12.43.167.59
Secondary SNTP Server . . . . . . . . . . . . . . . . . . . . ... 12.43.167.60
SNTP Poll Interval (minutes) . . . . . . . . . . . . . . . . . . . . . . ... 7
4-35
AI296 Version 9.8x User’s Guide
System Configuration: Time Configuration
Time Zone
Description
This menu item configures the time zone for AI296 to use. The configured value
represents the number of hours you are from UTC.
Menu Item Types
Data
AI296 Local Menu Item Configuration
1. Access the Time Menu located under the System Menu.
2. For Current Time Zone (+/-hh:mm), enter the time zone you want AI296 to use:
z
For +/-, enter the direction (+ = east) (- = west) of Universal Coordinated Time
(UTC) or Greenwich Mean Time.
z
z
For hh, enter the number of hours.
For mm, enter the number of minutes.
ꢀ
Note: The time entered is the number of hours you are from UTC. For example,
if you are located in the Eastern Standard Time (EST) zone, you would
enter -05:00 in this field. This indicates that you are 5 hours behind UTC.
This example displays a time zone configuration of -05:00.
Time Menu
Current Time Zone (+/-hh:mm) . . . . . . . . . . . . . . . . . . . . . .-05:00
4-36
AI296 Version 9.8x User’s Guide
IP Over X.25 Subnet Configuration: Configuration Overview
Configuration Overview
AI296 supports encapsulation of the IP protocol over X.25 (IXE) networks. The local
AI296 wraps IP packets (either control or data packets) inside of X.25 frames and
sends them across the X.25 network. The remote AI296 receives the X.25 frames and
unwraps the IP packets.
To allow IP traffic to run over an X.25 network, the network must be configured to
support IP over X.25 encapsulation. To do this, complete the following tasks:
z
Configure and verify the X.25 SVC links. Refer to section SVC Configuration
Settings on page 6-90 for information about configuring X.25 SVC links.
z
z
z
Create IP subnets and IP over X.25 remote pairs.
Create IP static routing table entries (optional).
Reset AI296.
Before Configuration
In order for the TCP/IP stack to know where to route incoming packets, an appropriate
subnet must be configured. IP addresses and subnets must be assigned to the local
and remote sides of the X.25 link (also called "doorway"). X.121 addresses are then
assigned to the local and remote sides. After this, a static route can be setup through
the IXE link to the remote doorway IP address. Refer to the example in Figure 5-1 on
page 5-2 for an illustration of how to configure IP over X.25.
Local AI296
IP address: 198.127.1.196
Subnet mask: 255.255.255.0
Remote AI296
IP address: 198.30.2.196
Subnet mask: 255.255.255.0
Link Numbers
Local IXE doorway
11
address: 20.0.0.1
Remote IXE doorway
address: 20.0.0.2
8
Local IXE doorway
X.121 address:
3035550005
Remote IXE doorway
X.121 address:
6065550008
IXE subnet mask:
255.255.255.0
IXE subnet mask:
255.255.255.0
IP Tunnel
within X.25
Figure 5-1 IXE Example
5-2
AI296 Version 9.8x User’s Guide
IP Over X.25 Subnet Configuration: Local Settings
Local Settings
IXE can be configured using either one local and one remote AI296 or one local AI296
and a router that supports IP over X.25. The following configuration components are
available:
z
z
z
Local IP Address for this Subnet
Description
This menu item configures the local IXE doorway address for the subnet.
ꢀ
Note: This address is not the same as the local AI296 IP address.
Menu Item Type
Data
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.13. This menu displays a list of all the configured IP over
X.25 subnets.
2. From Menu 4.2.11.13, enter a value (02 through 11) associated with the IP over
X.25 subnet to be configured. Menu 4.2.11.13.1 appears.
3. For 01 Local IP address for this subnet, enter the subnet IP address value. The
default is 0.0.0.0.
This example displays 01 Local IP address for this subnet set to 24.35.132.67.
>1,24.35.132.67
Menu 4.2.11.13.1
01 Local IP address for this subnet-----------------------------024.035.132.067
Configuration in the AI296 Local Menu System
1. Access the IP Over X.25 Subnet Menu.
2. From the IP Over X.25 Subnet Menu, select Add. The IP Over X.25 Subnet Edit
Menu appears.
3. For Local IP Address for this Subnet, enter the subnet IP address value.
5-3
AI296 Version 9.8x User’s Guide
IP Over X.25 Subnet Configuration: Local Settings
This example displays Local IP Address for this Subnet set to 24.35.132.67.
IP Over X.25 Subnet Edit Menu
Local IP Address for this Subnet . . . . . . . . . .......... 24.35.132.67
Local IP Subnet Mask
Description
This menu item configures the local IXE doorway IP subnet mask.
Menu Item Type
Data
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.13. This menu displays a list of all the configured IP over
X.25 subnets.
2. From Menu 4.2.11.13, enter a value (02 through 11) associated with the IP over
X.25 subnet to be configured. Menu 4.2.11.13.1 appears.
3. For 02 Local IP Mask for this subnet, enter the subnet IP subnet mask value. The
default is 255.255.255.252.
This example displays 02 Local IP Mask for this subnet set to 255.255.0.0.
>2,255.255.0.0
Menu 4.2.11.13.1
01 Local IP address for this subnet-----------------------------024.035.132.067
02 Local IP Mask for this subnet--------------------------------255.255.000.000
Configuration in the AI296 Local Menu System
1. Access the IP Over X.25 Subnet Menu.
2. From the IP Over X.25 Subnet Menu, select Add. The IP Over X.25 Subnet Edit
Menu appears.
3. For Local IP Mask for this Subnet, enter the subnet IP subnet mask value. The
default is 255.255.255.252.
This example displays Local IP Mask for this Subnet set to 255.255.0.0.
IP Over X.25 Subnet Edit Menu
Local IP Address for this Subnet . . . . . . . . . ............... 0.0.0.0
Local IP Mask for this Subnet . . . . . . . . . . . ........... 255.255.0.0
5-4
AI296 Version 9.8x User’s Guide
IP Over X.25 Subnet Configuration: Local Settings
Local X.25 Link Number
Description
This menu item configures the local IXE doorway link number.
Menu Item Type
Data
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.13. This menu displays a list of all the configured IP over
X.25 subnets.
2. From Menu 4.2.11.13, enter a value (02 through 11) associated with the IP over
X.25 subnet to be configured. Menu 4.2.11.13.1 appears.
3. For 03 Local X.25 link number, enter 3,and the link number. Valid values are 1 to
16. The default is 1.
This example displays 03 Local X.25 link number set to 12.
>3,12
Menu 4.2.11.13.1
01 Local IP address for this subnet-----------------------------024.035.132.067
02 Local IP Mask for this subnet--------------------------------255.255.000.000
03 Local X.25 link number----------------------------------------------------12
Configuration in the AI296 Local Menu System
1. Access the IP Over X.25 Subnet Menu.
2. From the IP Over X.25 Subnet Menu, select Add. The IP Over X.25 Subnet Edit
Menu appears.
3. For Local X.25 link number, enter the link number. The default is 1.
This example displays Local X.25 link number set to 12.
IP Over X.25 Subnet Edit Menu
Local IP Address for this Subnet . . . . . . . . . ............... 0.0.0.0
Local IP Mask for this Subnet . . . . . . . . . . . ....... 255.255.255.252
Local X.25 link number . . . . . . . . . . . . . . . . . . . . .12
5-5
AI296 Version 9.8x User’s Guide
IP Over X.25 Subnet Configuration: Remote Settings
Remote Settings
IXE can be configured using either one local and one remote AI296 or one local AI296
and a router that supports IP over X.25. The following configuration components are
available:
z
z
Remote IP Address for this Subnet
Description
This menu item configures the remote IXE IP address for the subnet.
ꢀ
Note: This address is not the same as the remote AI296 (or router) IP address.
Menu Item Type
Data
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.13. This menu displays a list of all the configured IP over
X.25 subnets.
2. From Menu 4.2.11.13, enter a value (02 through 11) associated with the IP over
X.25 subnet to be configured. Menu 4.2.11.13.1 appears.
3. For 04 Remote IP address for this subnet, enter the remote IP address value. The
default is 0.0.0.0.
This example displays 04 Remote IP address for this subnet set to 36.82.234.54.
>4,36.82.234.54
Menu 4.2.11.13.1
01 Local IP address for this subnet-----------------------------000.000.000.000
02 Local IP Mask for this subnet--------------------------------255.255.255.252
03 Local X.25 link number----------------------------------------------------01
04 Remote IP address for this subnet----------------------------036.082.234.054
Configuration in the AI296 Local Menu System
1. Access the IP Over X.25 Subnet Menu.
2. From the IP Over X.25 Subnet Menu, select Add. The IP Over X.25 Subnet Edit
Menu appears.
3. For Remote IP Address for this Subnet, enter the remote IP address value. The
default is 0.0.0.0.
5-6
AI296 Version 9.8x User’s Guide
IP Over X.25 Subnet Configuration: Remote Settings
This example displays Remote IP Address for this Subnet set to 93.67.158.56.
IP Over X.25 Subnet Edit Menu
Local IP Address for this Subnet . . . . . . . . . ............... 0.0.0.0
Local IP Mask for this Subnet . . . . . . . . . . . ....... 255.255.255.252
Local X.25 link number . . . . . . . . . . . . . . . . . . . . . 0
Remote IP Address for this Subnet . . . . . . . . . .......... 93.67.158.56
Remote X.121 Address
Description
This menu item configures the IXE remote X.121 address. Each IXE connection must
have a unique local/remote X.121 address pair. This means there cannot be two
separate IXE connections in the same AI296 with the same local X.121 address and
the same remote X.121 address.
ꢀ
Note: X.121 addresses are assigned per link on AI296, not per SVC.
Menu Item Type
Data
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.13. This menu displays a list of all the configured IP over
X.25 subnets.
2. From Menu 4.2.11.13, enter a value (02 through 11) associated with the IP over
X.25 subnet to be configure. Menu 4.2.11.13.1 appears.
3. For 05 Remote X121 address, enter 5,and the remote address value. Maximum
length is 15 characters.
This example displays 05 Remote X121 address set to 6505550043.
>5,6505550043
Menu 4.2.11.13.1
01 Local IP address for this subnet-----------------------------000.000.000.000
02 Local IP Mask for this subnet--------------------------------255.255.255.252
03 Local X.25 link number----------------------------------------------------01
04 Remote IP address for this subnet----------------------------036.082.234.054
05 Remote X121 address------------------------------------------
6505550043
5-7
AI296 Version 9.8x User’s Guide
IP Over X.25 Subnet Configuration: Remote Settings
Configuration in the AI296 Local Menu System
1. Access the IP Over X.25 Subnet Menu.
2. From the IP Over X.25 Subnet Menu, select Add. The IP Over X.25 Subnet Edit
Menu appears.
3. For Remote X121 Address, enter the remote address value.
This example displays Remote X121 Address set to 6505550043.
IP Over X.25 Subnet Edit Menu
Local IP Address for this Subnet . . . . . . . . . ............... 0.0.0.0
Local IP Mask for this Subnet . . . . . . . . . . . ....... 255.255.255.252
Local X.25 link number . . . . . . . . . . . . . . . . . . . . . 0
Remote IP Address for this Subnet . . . . . . . . . .......... 93.67.158.56
Remote X121 Address . . . . . . . . . . . . . . . . ........ 6505550043
5-8
AI296 Version 9.8x User’s Guide
Link Configuration: AI296 Link Types
AI296 Link Types
AI296 has six configurable link types:
z
z
z
z
z
z
Asynchronous
Asynchronous links use asynchronous transmission and support multiple baud rates,
parity types, stop bits, and software flow or hardware control.
See Also
z
z
z
z
z
Asynchronous PPP
Asynchronous PPP links use PPP (point-to-point protocol) and asynchronous
transmission. They support PAP and CHAP for authentication and can be set as
bridged (BCP) or routed (IPCP) interfaces.
See Also
z
z
z
z
z
z
z
6-2
AI296 Version 9.8x User’s Guide
Link Configuration: AI296 Link Types
HDLC-Bridge
HDLC-Bridge links run with an HDLC link layer protocol in Asynchronous Balanced
Mode and bridge Ethernet frames. HDLC-Bridge links can provide clocking or
synchronize with an external clock.
See Also
MLT
MLT links are designed for interfacing with the metallic loop testing switch application
found in telephone switch networks. This application consists of proprietary messages
transported using LAPB. The MLT link type enables the transporting of proprietary
messages across an IP network. LAPB is terminated on AI296 and the data is
transported to a remote end point using another transport protocol, such as TCP/IP.
See Also
z
z
z
z
Synchronous PPP
Synchronous PPP links use PPP (point-to-point protocol) and synchronized
transmission. They can provide clocking or synchronize with an external clock.
Synchronous PPP links support PAP and CHAP for authentication and can be set as
bridged (BCP) or routed (IPCP) interfaces.
See Also
z
z
z
6-3
AI296 Version 9.8x User’s Guide
Link Configuration: AI296 Link Types
X.25
X.25 links provide a synchronous connection to a packet-switched X.25 network. X.25
links can behave as DTE or DCE and can provide clocking or synchronize with an
external clock. X.25 links support both PVC and SVC calls and allow configuration of
a variety of LAPB and X.25 protocol settings.
See Also
z
z
z
z
z
6-4
AI296 Version 9.8x User’s Guide
Link Configuration: BX.25 Configuration
BX.25 Configuration
AI296 is BX.25 compatible and implements passive links. Passive links are not a part
of the BX.25 protocol. Once a passive link is active, it uses the BX.25 protocol.
ꢀ
Notes: BX.25 is supported on only one link per AI296.
ꢀ Some BX.25 parameters may vary based on the AI296 installation.
The following configuration components are available:
z
z
z
z
BX.25 Configuration Values Usage
Description
This menu item enables or disables the use of the values configured in the BX.25
menu.
Menu Item Type
Toggle
Link Type Availability
X.25
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.12.11.
2. For 02*Use these configuration values, enter 2to select Enabled or Disabled. The
default is Enabled.
This example displays 02*Use these configuration values set to Enabled.
>2
Menu 4.2.11.12.11
01*BX25 Support (Enabled, Disabled)------------------------------------ Enabled
02*Use these configuration values (Enabled, Disabled)------------------ Enabled
6-5
AI296 Version 9.8x User’s Guide
Link Configuration: BX.25 Configuration
Configuration in the AI296 Local Menu System
1. Access the X.25 Link Menu.
2. Select BX.25 Menu. The BX.25 Menu appears.
3. For Use BX.25 Configuration Values, select Enabled or Disabled. The default is
Enabled.
This example displays Use BX.25 Configuration Values set to Enabled.
BX.25 Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
03
Disabled
Disabled
BX.25 Support . . . . . . . . . . . . . . . . . . . .
Use BX.25 Configuration Values. . . . . . . . . . . .
[Enabled]
[Enabled]
BX.25 Modulo
Description
This menu item defines a modulo value. A modulo is used by the BX.25 protocol to
define the value at which the packet sequence numbers will rollover.
Menu Item Type
Data
Link Type Availability
X.25
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.12.11.
2. For 04 Modulo, enter 4,and the desired value. The default is 256.
This example displays 04 Modulo set to 200.
>4,200
Menu 4.2.11.12.11
01*BX25 Support (Enabled, Disabled)------------------------------------Disabled
02*Use these configuration values (Enabled, Disabled)------------------ Enabled
03 Sending Unit Number (0 - 9)------------------------------------------------0
04 Modulo (5 - 256)---------------------------------------------------------200
6-6
AI296 Version 9.8x User’s Guide
Link Configuration: BX.25 Configuration
Configuration in the AI296 Local Menu System
1. Access the X.25 Link Menu.
2. Select BX.25 Menu. The BX.25 Menu appears.
3. For BX.25 Modulo, enter the desired value. The default is 256.
This example displays BX.25 Modulo set to 150.
BX.25 Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
03
BX.25 Support . . . . . . . . . . . . . . . . . . . .
Use BX.25 Configuration Values. . . . . . . . . . . .
Enabled
[Disabled]
Disabled
[Enabled]
Sending Unit Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
BX.25 Modulo. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .150
BX.25 Support
Description
This menu item enables or disables BX.25 module support on a link. BX.25 support
can only be enabled on one link at a time. When enabling BX.25 support, first disable
support on all other links.
Menu Item Type
Toggle
Link Type Availability
X.25
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.12.11.
2. For 01*BX25 Support, enter 1to select Enabled or Disabled. The default is Disabled.
This example displays 01*BX25 Support set to Enabled.
>1
Menu 4.2.11.12.11
01*BX25 Support (Enabled, Disabled)------------------------------------ Enabled
6-7
AI296 Version 9.8x User’s Guide
Link Configuration: BX.25 Configuration
Configuration in the AI296 Local Menu System
1. Access the X.25 Link Menu.
2. Select BX.25 Menu. The BX.25 Menu appears.
3. For BX.25 Support, select Enabled or Disabled. The default is Disabled.
This example displays BX.25 Support set to Enabled.
BX.25 Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
03
BX.25 Support . . . . . . . . . . . . . . . . . . . .
[Enabled]
Disabled
BX.25 Timer Settings
Description
The initial BX.25 timer settings are configured using two menu items:
z Connect timer ST2—Defines the maximum number of seconds that the BX.25
protocol will wait for a response to a session connect request.
z Send timer ST3—Defines the data acknowledge timer, which gives the maximum
number of seconds that the BX.25 protocol will wait for an acknowledgement to a
Data Request.
Menu Item Type
Data
Link Type Availability
X.25
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.12.11.
2. For 05 Connect Timer ST2, enter 5,and the connect timer value. Valid values are 0
to 65535. The default is 12.
3. For 06 Send Timer ST3, enter 6,and the send timer value. Valid values are 0 to
65535. The default is 18.
6-8
AI296 Version 9.8x User’s Guide
Link Configuration: BX.25 Configuration
This example displays 05 Connect Timer ST2 set to 33 and 06 Send Timer ST3 set to 45.
>6,35
Menu 4.2.11.12.11
01*BX25 Support (Enabled, Disabled)------------------------------------ Enabled
02*Use these configuration values (Enabled, Disabled)------------------ Enabled
03 Sending Unit Number (0 - 9)------------------------------------------------2
04 Modulo (5 - 256)---------------------------------------------------------122
05 Connect Timer ST2 (seconds)--------------------------------------------00033
06 Send Timer ST3 (seconds)-----------------------------------------------00045
Configuration in the AI296 Local Menu System
1. Access the X.25 Link Menu.
2. From the X.25 Link Menu, select the BX.25 Menu.
3. For Connect Timer ST2, enter the connect timer value. The default is 12.
4. For Send Timer ST3, enter the send timer value. The default is 18.
This example displays Connect Timer ST2 set to 225 and Send Timer ST3 set to 275.
BX.25 Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
03
Disabled
Disabled
BX.25 Support . . . . . . . . . . . . . . . . . . . .
[Enabled]
Use BX.25 Configuration Values. . . . . . . . . . . .
[Enabled]
Sending Unit Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
BX.25 Modulo. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .200
Connect Timer ST2 (seconds) . . . . . . . . . . . . . . . . . . . . . . .. 225
Send Timer ST3 (seconds). . . . . . . . . . . . . . . . . . . . . . . . .. 275
6-9
AI296 Version 9.8x User’s Guide
Link Configuration: Connect Options Configuration
Connect Options Configuration
Connect options configure the AI296 connection parameters. These options are
available for asynchronous links and asynchronous PPP links. The following
configuration items are available:
z
z
z
z
z
Alias
Description
This menu item specifies an alias name for the connection. When the link connection
options are satisfied, a call is placed based on information contained in the alias
name.
The specified name must correspond to an alias that has been created in the Alias
Menu. If no alias name is specified and Link Application is set to ALIAS in the AI198
menu system (AppAlias in the AI296 local menu system), then a default alias is used.
The default alias is the concatenation of the string asy. with the numeric link number,
such as asy.3, which indicates link number 3.
ꢀ
Note: The 02 Alias menu item is used only if 01*Link Application is set to ALIAS
(AppAlias in the AI296 local menu system).
Menu Item Type
Data
Link Type Availability
Async
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.12.11.
2. For 02 Alias, enter 2,and the alias name.
6-10
AI296 Version 9.8x User’s Guide
Link Configuration: Connect Options Configuration
This example displays 02 Alias set to async.4.1.
>2,async.4.1
Menu 4.2.11.12.11
01*Link Application (Login, Destination, Alias)---------------------------ALIAS
02 Alias--------------------------------------------------------------async.4.1
Configuration in the AI296 Local Menu System
1. Access the Async Link Menu.
2. Select Connect Options Menu. The Connect Options Menu appears.
3. For Link Application Alias, enter the alias value.
This example displays Link Application Alias set to async.4.1.
Connect Options Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
1
Link Application . . . . . . . . . . . .
Login
Destination
[AppAlias]
Link Application Alias . . . . . . ................................. async.4.1
Call Retry Interval
Description
This menu item defines a value for the call retry interval. If a call fails to connect and
the retry interval is greater than 0, the link attempts to place the call again after the
specified number of seconds elapse. This setting has no effect on calls placed to the
link when the link is the destination and not the call originator. A value of 0 disables
call retry interval functionality.
Menu Item Type
Data
Link Type Availability
Async
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.12.11.
2. For 03 Call retry interval, enter 3,and the interval value. The default is 0.
6-11
AI296 Version 9.8x User’s Guide
Link Configuration: Connect Options Configuration
This example displays 03 Call retry interval set to 134.
>3,134
Menu 4.2.11.12.11
01*Link Application (Login, Destination, Alias)---------------------------ALIAS
02 Alias--------------------------------------------------------------async.4.1
03 Call retry interval (0 - 32767 s, 0 = disabled)------------------------00134
Configuration in the AI296 Local Menu System
1. Access the Async Link Menu.
2. Select Connect Options Menu. The Connect Options Menu appears.
3. For Call Retry Interval, enter the desired interval value. The default is 0.
This example displays Call Retry Interval set to 134.
Connect Options Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
1
Link Application . . . . . . . . . . . . Login Destination [AppAlias]
Link Application Alias . . . . . . ................................. async.4.1
Call Retry Interval (0 - 32767s, 0 = disable) . . . . . . . . . . . . . .. 134
Connect String
Description
This menu item configures the string that is sent after a connection is established. The
following character values apply:
z <b>sends a break signal.
z <n>represents the decimal value of an ASCII character. Valid values are 0 to 255.
z textrepresents the text value in the string.
z <p #>represents a pause control sequence. #is the number of tenths of seconds
to pause. Valid values are 1 to 20 (for 0.1 seconds to 2 seconds).
For example, string <b>login<13><p 10><b> sends:
z
z
z
z
z
A break signal
Text “login”
A carriage return
A 1 second pause
Another break signal.
6-12
AI296 Version 9.8x User’s Guide
Link Configuration: Connect Options Configuration
Menu Item Type
Data
Link Type Availability
Async
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.12.11.
2. For 08 Connect string, enter 8,and the connect string.
This example displays 08 Connect string set to <b>newstring<33><p 13><b>.
>8,<b>newstring<33><p 13><b>
Menu 4.2.11.12.11
01*Link Application (Login, Destination, Alias)---------------------------ALIAS
02 Alias--------------------------------------------------------------async.4.1
03 Call retry interval (0 - 32767 s, 0 = disabled)------------------------00134
04 Dial/Connect when DSR is on----------------------------------------------N/A
05*Connect when DCD is on---------------------------------------------------OFF
06*Connect when characters are received------------------------------------- ON
07*Connect without DSR, DCD or received characters--------------------------OFF
08 Connect string-------------------------------------<b>newstring<33><p 13><b>
Configuration in the AI296 Local Menu System
1. Access the Async Link Menu.
2. Select Connect Options Menu. The Connect Options Menu appears.
3. For Connect String, enter the connect string.
This example displays Connect String set to <b>newstring<33><p 13><b>.
Connect Options Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
1
Link Application . . . . . . . . . . . . Login Destination [AppAlias]
Link Application Alias . . . . . . ................................. async.4.1
Call Retry Interval (0 - 32767s, 0 = disable) . . . . . . . . . . . . . .. 134
Dial/Connect when DSR is on . . . . . . . . . . . . . . . . . .
Connect when DCD is on. . . . . . . . . . . . . . . . . . . . .
Connect when characters are received. . . . . . . . . . . . . .
Connect without DSR, DCD or received characters . . . . . . . .
On
[On]
On
[Off]
Off
[Off]
[Off]
On
Connect String . . . . . . . . . . . ............... <b>newstring<33><p 13><b>
6-13
AI296 Version 9.8x User’s Guide
Link Configuration: Connect Options Configuration
Connection Settings
Description
The connection settings are configured using three menu items:
z Connect when DCD is on—Enables or disables link connection when DCD is
asserted. If Connect when characters are received is also enabled and is satisfied
first, then Connect when DCD is on has no effect on the link connection.
z Connect when characters are received—Enables or disables the link connection
when incoming characters are received. If Connect when DCD is on is also enabled
and is satisfied first, then Connect when characters are receivedhas no effect on the
link connection.
z Connect without DSR, DCD or received characters—When this menu item is enabled,
Connect when DCD is on and Connect when characters are received are forced off and
the retry interval is set to 30. If the link application type is set to LOGIN or ALIAS,
connection will occur as soon as the link is enabled (completely independent from
the DCD and incoming character status). If the link application type is set to
DESTINATION, the link will connect immediately when an outgoing call is placed to
the destination (also completely independent from DCD and incoming character
status).
ꢀ
Note: Dial/Connect when DSR is on has no effect on AI296 operation.
Menu Item Type
Toggle
Link Type Availability
Async
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.12.11.
2. For 05*Connect when DCD is on, enter 5to select ON or OFF. The default is OFF.
3. For 06*Connect when characters are received, enter 6to select ON or OFF. The default
is ON.
4. For 07*Connect without DSR, DCD or received characters, enter 7to select ON or OFF.
The default is OFF.
6-14
AI296 Version 9.8x User’s Guide
Link Configuration: Connect Options Configuration
This example displays:
z 05*Connect when DCD is on set to ON
z 06*Connect when characters are received set to OFF
z 07*Connect without DSR, DCD or received characters set to OFF.
>5
Menu 4.2.11.12.11
01*Link Application (Login, Destination, Alias)---------------------------ALIAS
02 Alias--------------------------------------------------------------async.4.1
03 Call retry interval (0 - 32767 s, 0 = disabled)------------------------00030
04 Dial/Connect when DSR is on----------------------------------------------N/A
05*Connect when DCD is on--------------------------------------------------- ON
06*Connect when characters are received-------------------------------------OFF
07*Connect without DSR, DCD or received characters--------------------------OFF
Configuration in the AI296 Local Menu System
1. Access the Async Link Menu.
2. Select Connect Options Menu. The Connect Options Menu appears.
3. For Connect when DCD is on, select ON or OFF. The default is OFF.
4. For Connect when characters are received, select ON or OFF. The default is ON.
5. For Connect without DSR, DCD or received characters, select ON or OFF. The default is
OFF.
This example displays:
z Connect when DCD is on set to On
z Connect when characters are received set to Off
z Connect without DSR, DCD or received characters set to Off.
Connect Options Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
1
Link Application . . . . . . . . . . . . Login Destination [AppAlias]
Link Application Alias . . . . . . ................................. async.4.1
Call Retry Interval (0 - 32767s, 0 = disable) . . . . . . . . . . . . . .. 134
Dial/Connect when DSR is on . . . . . . . . . . . . . . . . . .
Connect when DCD is on. . . . . . . . . . . . . . . . . . . . .
Connect when characters are received. . . . . . . . . . . . . .
Connect without DSR, DCD or received characters . . . . . . . .
On
[On]
On
[Off]
Off
[Off]
[Off]
On
6-15
AI296 Version 9.8x User’s Guide
Link Configuration: Connect Options Configuration
Link Application
Description
This menu item configures the link application type. The following options are
available:
z Login—Specifies that the link will prompt for a user name and password when
connected. Upon successful login, a menu appears showing the available
destination alias names.
z Destination—Specifies that the link does not accept incoming calls. The link must
be accessed internally using alias lookup from another link or from a TCP/IP
connection.
z Alias (AppAlias)—Specifies that the link will attempt to place a call using direct
alias lookup without displaying a destination menu. If the link has a link application
alias name configured, then that name is used. Otherwise, a default alias name
(ASY.linkNum) is used.
Menu Item Type
Toggle
Link Type Availability
Async
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.12.11.
2. For 01*Link Application, enter 1to select LOGIN, DESTINATION, or ALIAS. The default is
LOGIN.
This example displays 01*Link Application set to DESTINATION.
>1
Menu 4.2.11.12.11
01*Link Application (Login, Destination, Alias)---------------------DESTINATION
6-16
AI296 Version 9.8x User’s Guide
Link Configuration: Connect Options Configuration
Configuration in the AI296 Local Menu System
1. Access the Async Link Menu.
2. Select Connect Options Menu. The Connect Options Menu appears.
3. For Link Application, select Login, Destination, or AppAlias. The default is Login.
This example displays Link Application set to Destination.
Connect Options Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
1
Link Application . . . . . . . . . . . .
Login
[Destination]
AppAlias
6-17
AI296 Version 9.8x User’s Guide
Link Configuration: Disconnect Options Configuration
Disconnect Options Configuration
Disconnect options configure the parameters that are used when AI296 disconnects.
These options are available for asynchronous and asynchronous PPP links. The
following configuration items are available:
z
z
z
Disconnect Inactivity Timer Settings
Description
The disconnect inactivity timer settings are configured using three menu items:
z Disconnect inactivity timer—Defines an inactivity timer value. This value
establishes a timeout interval after which the link will automatically disconnect if
no data has been sent or received for the specified number of seconds. This value
only applies to incoming calls on links that have a retry interval timer setting of 0
and a link application setting of LOGIN or ALIAS (AppAlias).
ꢀ
Note: The Disconnect inactivity timeroption must be set to a value greater than
0 for the inactivity timer to function.
z Inactivity timer enabled when link receives call—Enables or disables the
disconnect inactivity timer when the link receives a call.
z Inactivity timer resets on incoming characters from destination—When enabled,
incoming characters count as activity on a link (the inactivity timer resets). When
disabled, they do not count (the inactivity timer does not reset).
Menu Item Type
Data for disconnect inactivity timer
Toggle for Inactivity timer enabled when link receives call and Inactivity timer resets
on incoming characters from destination
Link Type Availability
Async
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.12.12.
2. For 04 Disconnect inactivity timer, enter 4,and the timer value. The default is 0.
6-18
AI296 Version 9.8x User’s Guide
Link Configuration: Disconnect Options Configuration
3. For 05*Inactivity Timer enabled when link receives call, enter 5to select ON or OFF.
The default is OFF.
4. For 06*Inactivity Timer resets on incoming characters from destination, enter 6to
select ON or OFF. The default is ON.
This example displays:
z 04 Disconnect inactivity timer set to 236
z 05*Inactivity Timer enabled when link receives call set to ON
z 06*Inactivity Timer resets on incoming characters from destination set to OFF.
>12
Menu 4.2.11.12.12
01 Disconnect when DSR off--------------------------------------------------N/A
02*Disconnect when DCD off--------------------------------------------------OFF
03*Disconnect when a break character is received---------------------------- ON
04 Disconnect inactivity timer (0 - 32767 s, 0 = disabled)----------------00236
05*Inactivity Timer enabled when link receives call------------------------- ON
06*Inactivity Timer resets on incoming characters from destination----------OFF
Configuration in the AI296 Local Menu System
1. Access the Async Link Menu.
2. Select Disconnect Options Menu. The Disconnect Options Menu appears.
3. For Disconnect inactivity timer, enter the timer value. The default is 0.
4. For Inactivity Timer enabled when link receives call, select On or Off. The default
is Off.
5. For Inactivity Timer resets on incoming characters from destination, select On or
Off. The default is On.
This example displays:
z Disconnect inactivity timer set to 367.
z Inactivity Timer enabled when link receives call set to On.
z Inactivity Timer resets on incoming characters from destination set to Off.
Disconnect Options Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
3
Disconnect when DCD is off . . . . . . . . . . . . . . . . . . .
Disconnect when a Break character is received . . . . . . . . .
On
[On]
[Off]
Off
Disconnect inactivity timer (0 - 32767s, 0 = disabled) . . . . . . . . . .. 367
Inactivity Timer enabled when link receives call . . . . . . . .
Inactivity Timer resets on incoming characters from destination
[On]
On
Off
[Off]
6-19
AI296 Version 9.8x User’s Guide
Link Configuration: Disconnect Options Configuration
Disconnect Settings
Description
The disconnect settings are configured using two menu items:
z Disconnect when a break character is received—Enables or disables link
disconnection when a break character is received.
z Disconnect when DCD off—Enables or disables link disconnection when DCD is not
asserted.
ꢀ
Note: AI296 does not consider the DSR state when disconnecting calls.
Menu Item Type
Toggle
Link Type Availability
Both menu items are available for async links
Menu item Disconnect when DCD off is available for asyncPPP links
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.12.12.
2. For 02*Disconnect when DCD off, enter 2to select ON or OFF. The default is OFF.
3. For 03*Disconnect when a break character is received, enter 3to select ON or OFF.
The default is ON.
This example displays 02*Disconnect when DCD off set to ON and 03*Disconnect when a
break character is received set to OFF.
>3
Menu 4.2.11.12.12
01 Disconnect when DSR off--------------------------------------------------N/A
02*Disconnect when DCD off-------------------------------------------------- ON
03*Disconnect when a break character is received----------------------------OFF
Configuration in the AI296 Local Menu System
1. Access the Async Link Menu.
2. Select Disconnect Options Menu. The Disconnect Options Menu appears.
3. For Disconnect when DCD is off, select On or Off. The default is Off.
4. For Disconnect when a Break character is received, select On or Off. The default is
On.
6-20
AI296 Version 9.8x User’s Guide
Link Configuration: Disconnect Options Configuration
This example displays Disconnect when DCD is offset to Onand Disconnect when a Break
character is received set to Off for an async link.
Disconnect Options Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
4
Disconnect when DCD is off . . . . . . . . . . . . . . . . . . .
Disconnect when a Break character is received . . . . . . . . .
[On]
On
Off
[Off]
Disconnect String
Description
This menu item configures the string the link sends before the link disconnects. The
following character values apply:
z <b>sends a break signal.
z <n>represents the decimal value of an ASCII character. Valid values are 0 to 255.
z textrepresents the text value in the string.
z <p #>represents a pause control sequence. #is the number of tenths of seconds
to pause. Valid values are 1 to 20 (for 0.1 seconds to 2 seconds).
For example, string <b>login<13><p 10><b> sends:
z
z
z
z
z
A break signal
The text “login”
A carriage return
A one second pause
Another break signal.
Menu Item Type
Data
Link Type Availability
Async
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.12.12.
2. For 07 Disconnect string, enter 7,and the disconnect string. Maximum length is
80 characters.
6-21
AI296 Version 9.8x User’s Guide
Link Configuration: Disconnect Options Configuration
This example displays 07 Disconnect string set to <b>newString<33><p 15><b>.
>7,<b>newString<33><p 15><b>
Menu 4.2.11.12.12
01 Disconnect when DSR off--------------------------------------------------N/A
02*Disconnect when DCD off-------------------------------------------------- ON
03*Disconnect when a break character is received----------------------------OFF
04 Disconnect inactivity timer (0 - 32767 s, 0 = disabled)----------------00000
05*Inactivity Timer enabled when link receives call-------------------------OFF
06*Inactivity Timer resets on incoming characters from destination---------- ON
07 Disconnect string----------------------------------<b>newString<33><p 15><b>
Configuration in the AI296 Local Menu System
1. Access the Async Link Menu.
2. Select Disconnect Options Menu. The Disconnect Options Menu appears.
3. For Disconnect String, enter the disconnect string.
This example displays Disconnect String set to <b>newString<33><p 15><b>.
Disconnect Options Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
3
Disconnect when DCD is off . . . . . . . . . . . . . . . . . . .
Disconnect when a Break character is received . . . . . . . . .
Disconnect inactivity timer (0 - 32767s, 0 = disabled) . . . . . . . . . .. 367
[On]
On
Off
[Off]
Inactivity Timer enabled when link receives call . . . . . . . .
Inactivity Timer resets on incoming characters from destination
Disconnect String . . . . . . . . . . .............. <b>newString<33><p 15><b>
[On]
On
Off
[Off]
6-22
AI296 Version 9.8x User’s Guide
Link Configuration: General Link Properties Configuration
General Link Properties Configuration
General link properties are configurable using menus accessed directly from the link
configuration menu. The following configuration items are available:
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
Auto Disable Error Limit
Description
This menu item disables a link when the rate of errors received on that link exceeds a
user-specified threshold. This prevents a bad link or cable from streaming enough
errors to lock up or crash AI296.
Menu Item Type
Data
Link Type Availability
Async, AsyncPPP, HDLC-Bridge, MLT, SyncPPP, and X.25
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.12.
2. For Auto Disable Error Limit, enter the associated item number, a comma, and the
error limit value. (For example, 9,25000.) The default is 0.
6-23
AI296 Version 9.8x User’s Guide
Link Configuration: General Link Properties Configuration
This MLT link example displays 09 Auto Disable Error Limit set to 25000.
>9,25000
Menu 4.2.11.12
01 Link number (1-16)--------------------------------------------------------01
02*Link Type (Async, X25, HDLC, SyncPPP, AsyncPPP, MLT)---------------- MLT
03 Link Description------------------------------ Async link 1
04*Link state (Enabled, Disabled)-------------------------------------- Enabled
05 Port speed (0 - 128000 bps, 0 is external clocking)-------------------009600
06*Hardware Interface (RS232,RS530,V.35)----------------------------------RS232
07*Sync Port Encoding (NRZ, NRZI)-------------------------------------------NRZ
08+LAPB Parameters
09 Auto Disable Error Limit (0-1000000)---------------------------------0025000
Configuration in the AI296 Local Menu System
1. Access the Link Menu.
2. Select Auto Disable Menu. The Link Auto Disable Menu appears.
3. For Errors/second limit for auto disable, enter the error limit value. The default
is 0.
This example displays Errors/second limit for auto-disable set to 25000.
Link Auto Disable Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
03
Errors/second limit for auto-disable . . . . . . . . . . . . . . . . . . 25000
Flow Control
Description
This menu item enables a receiving device to tell a sending device to stop sending
data when data is coming too fast and to start sending data when the receiver is
ready.
There are two available flow control options for AI296:
z None—Specifies no flow control.
z XonXoff—Specifies the flow control option that uses standard ASCII control
characters to tell a sending device to stop or resume data transmission.
Menu Item Type
Toggle
Link Type Availability
Async and AsyncPPP
6-24
AI296 Version 9.8x User’s Guide
Link Configuration: General Link Properties Configuration
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.12.
2. For 09*Flow Control, enter 9to select None or XonXoff. The default is None.
This async link example displays 09*Flow Control set to XonXoff.
>9
Menu 4.2.11.12
01 Link Number (1-16)--------------------------------------------------------01
02*Link Type (Async, X25, HDLC, SyncPPP, AsyncPPP, MLT)---------------- Async
03 Link Description------------------------------ Async link 1
04*Link state (Enabled, Disabled)-------------------------------------- Enabled
05+Port speed------------------------------------------------------------- 9600
06*Port Data Bits (7, 8)------------------------------------------------------8
07*Port Stop Bits (1, 2)------------------------------------------------------1
08*Port Parity (None, Odd, Even)-------------------------------------------None
09*Flow Control (None, XonXoff)-----------------------------------------XonXoff
Configuration in the AI296 Local Menu System
1. Access the Link Menu.
2. For SW Flow Control, select None or XonXoff.
This example displays SW Flow Control set to XonXoff.
Async Link Menu
Link to configure . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Link Description . . . . . . . . . . . . . . .................. Async link 1
Link state . . . . . . . . . . . . . . . . . . . . .
[Enabled]
AsyncPPP
Disabled
ModMux
Link Type . . . . . . . . . . . . . . . . .
Port speed (in bits per second):
[Async]
300
Autobaud
1200
2400
4800
[9600]
19.2K
38.4K
57.6K
Seven
115.2K
Port data bits . . . . . . . . . . . . . . . . . . . . .
Port stop bits . . . . . . . . . . . . . . . . . . . . . . .
[Eight]
[One]
Even
Two
Odd
[XonXoff]
Port parity . . . . . . . . . . . . . . . . . . . .
SW Flow Control . . . . . . . . . . . . . . . . . . . .
[None]
None
Hardware Interface (Interface Type)
Description
This menu item configures the hardware connection used for an AI296 link. The
following hardware connections are available:
z RS232—A data transmission standard that defines the characteristics for
connecting DTE and DCE data communications devices.
z RS530—A data transmission standard that is similar to RS232, but with support for
higher data rates (ranging from 20 Kbps to 2 Mbps).
6-25
AI296 Version 9.8x User’s Guide
Link Configuration: General Link Properties Configuration
z V.35—Data transmission standard for a trunk interface between a network access
device and a packet network.
Menu Item Type
Toggle
Link Type Availability
Async, AsyncPPP, HDLC-Bridge, MLT, SyncPPP, and X.25
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.12.
2. For Hardware Interface, enter the associated item number to select RS232, RS530, or
V.35. The default is RS232.
This asynchronous link example displays 15*Hardware Interface set to V.35.
>15
Menu 4.2.11.12
01 Link Number (1-16)--------------------------------------------------------01
02*Link Type (Async, X25, HDLC, SyncPPP, AsyncPPP, MLT)----------------
Async
03 Link Description------------------------------ Async link 1
04*Link state (Enabled, Disabled)-------------------------------------- Enabled
05+Port speed------------------------------------------------------------- 9600
06*Port Data Bits (7, 8)------------------------------------------------------8
07*Port Stop Bits (1, 2)------------------------------------------------------1
08*Port Parity (None, Odd, Even)-------------------------------------------None
09*Flow Control (None, XonXoff)-----------------------------------------
10 Xon Repeat interval (0 - 120s with 0 = no repeat)------------------------000
None
11+Connect Options
12+Disconnect Options
13+RTS/DTR Lead Control Options
14+Modem Options
15*Hardware Interface (RS232,RS530,V.35)-----------------------------------V.35
Configuration in the AI296 Local Menu System
1. Access the Link Menu.
2. For Interface Type, select RS-232, RS-530, or V.35.
This example displays Interface Type set to V.35.
Async Link Menu
Link to configure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Link state . . . . . . . . . . . . . . . . . . . . . . . . . .
Up
[Down]
MLT
[V.35]
Link Type . .
[Async]
X.25
HDLC-Bridge
SyncPPP
RS-232
AsyncPPP
RS-530
Interface Type . . . . . . . . . . . . . . . . .
6-26
AI296 Version 9.8x User’s Guide
Link Configuration: General Link Properties Configuration
Interface Mode
Description
This menu item configures the interface mode as either DTE or DCE. DTE is used for
a communications device (typically a terminal or computer) that is the source or
destination of signals on a network. DCE is used for a device (typically the modem)
that establishes, maintains, and terminates a session on a network. It may also
convert signals for transmission.
Menu Item Type
Toggle
Link Type Availability
MLT and X.25
Configuration in the AI198 Menu System
1. Access menu 4.2.11.12.8 for MLT or menu 4.2.11.12.7 for X.25.
2. For 01*Interface mode, enter 1to select DCE or DTE. The default is DCE.
This example displays 01*Interface mode set to DTE for an MLT link.
>1
Menu 4.2.11.12.8
01*Interface mode (DTE or DCE)----------------------------------------------DTE
Configuration in the AI296 Local Menu System
For MLT links:
1. Access the MLT Link Menu.
2. For Interface Mode, select DCE or DTE. The default is DCE.
This example displays Interface Mode set to DTE.
MLT Link Menu
Link to configure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Link state . . . . . . . . . . . . . . . . . . . . . . . . . .
[Up]
Down
[MLT]
V.35
Link Type . .
Async
X.25
HDLC-Bridge
SyncPPP
[RS-232]
AsyncPPP
RS-530
Interface Type . . . . . . . . . . . . . . . . .
Link Description . . . . . . . . . . . . . . .................. Async link 1
Interface Mode . . . . . . . . . . . . . . . . . . . . . . . [DTE] DCE
6-27
AI296 Version 9.8x User’s Guide
Link Configuration: General Link Properties Configuration
For X.25 links:
1. Access the X.25 Link Menu.
2. From the X.25 Link Menu, select Quick X.25 Menu. The Quick X.25 Menu appears.
3. For Interface Mode, select DCE or DTE. The default is DCE.
This example displays Interface Mode set to DTE.
Quick X.25 Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
Interface Mode . . . . . . . . . . . . . . . . . . . . . . . [DTE]
01
DCE
Link Description
Description
This menu item defines a description for a link.
Menu Item Type
Data
Link Type Availability
Async, AsyncPPP, HDLC-Bridge, MLT, SyncPPP, and X.25
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.12.
2. For 03 Link Description, enter 3,and a description associated with the link.
Maximum length is 30 characters.
This example displays 03 Link Description set to New X.25 Link.
>3,New X.25 Link
Menu 4.2.11.12
01 Link number (1-16)--------------------------------------------------------03
02*Link Type (Async, X25, HDLC, SyncPPP, AsyncPPP, MLT)----------------
03 Link Description------------------------------
X.25
New X.25 Link
Configuration in the AI296 Local Menu System
1. Access the Link Menu.
2. For Link Description, enter a description associated with the link. Maximum length
is 30 characters.
6-28
AI296 Version 9.8x User’s Guide
Link Configuration: General Link Properties Configuration
This example displays Link Description set to New X.25 Link.
X.25 Link Menu
Link to configure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Link state . . . . . . . . . . . . . . . . . . . . . . . . . .
Link Type . . Async [X.25] HDLC-Bridge SyncPPP
Interface Type . . . . . . . . . . . . . . . . . RS-232
[Up]
Down
MLT
V.35
AsyncPPP
[RS-530]
Link Description . . . . . . . . . . . . . . ................. New X.25 Link
Link Mode
Description
This menu item defines the mode of operation for an X.25 link as normal, passive, or
extended:
z
z
Normal mode is used for normal X.25 service.
Passive mode allows AI296 to operate with the SCCS application of the AT&T
5ESS. The SCCS application requires redundant links at the 5ESS. These links
are called SCC0B and SCC1B. Only one link is active at a time. The 5ESS
constantly tries to bring up whichever link is idle. If the 5ESS has SCC0B active, it
will try to bring up SCC1B. If SCC1B comes up, the 5ESS will drop SCC0B and
send information on SCC1B. Passive mode ensures that either SCC0B or SCC1B
will be up, but not simultaneously.
z
Extended mode supports passive link capability to the 5ESS over a TCP/IP
network. Extended mode ensures that either SCC0A or SCC1A will be up but not
simultaneously and will temporarily take down the corresponding link if
connections fail or cannot be placed because the corresponding remote link is
down.
Menu Item Type
Toggle
Link Type Availability
X.25
Configuration in the AI198 Menu System
1. Access Menu 4.2.1114.12.
2. For 05*Link mode, enter 5to select Normal, Passive, or Extended. The default is Normal.
6-29
AI296 Version 9.8x User’s Guide
Link Configuration: General Link Properties Configuration
This example displays 05*Link mode set to Passive.
>5
Menu 4.2.11.12
01 Link number (1-16)--------------------------------------------------------01
02*Link Type (Async, X25, HDLC, SyncPPP, AsyncPPP, MLT)---------------- X.25
03 Link Description------------------------------ Async link 1
04*Link state (Enabled, Disabled)-------------------------------------- Enabled
05*Link mode (Normal, Passive, Extended)------------------------------- Passive
Configuration in the AI296 Local Menu System
1. Access the X.25 Link Menu.
2. From the X.25 Link Menu, select Quick X.25 Menu. The Quick X.25 Menu appears.
3. For X25 Passive Link Mode, select Normal, Passive, or Extended. The default is normal.
This example displays X25 Passive Link Mode set to Passive.
Quick X.25 Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
Interface Mode . . . . . . . . . . . . . . . . . . . . . . . DTE
03
[DCE]
Port speed (0=external clocking) . . . . . . . . . . . . . . . . . . . . 4800
X25 Passive Link Mode . . . . . . . . . . . Normal [Passive] Extended
Link Number
Description
This menu item defines the number of the link being configured.
Menu Item Type
Data
Link Type Availability
Async, AsyncPPP, HDLC-Bridge, MLT, SyncPPP, and X.25
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.12.
2. For 01 Link number, enter 1,and the link number. The default is 1.
6-30
AI296 Version 9.8x User’s Guide
Link Configuration: General Link Properties Configuration
This example displays 01 Link number set to 3.
>1,3
Menu 4.2.11.12
01 Link number (1-16)--------------------------------------------------------03
Configuration in the AI296 Local Menu System
1. Access the Link Menu.
2. For Link to configure, enter the link number. The default is 1.
This example displays Link to configure set to 3.
Async Link Menu
Link to configure . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Link State
Description
This menu item enables or disables a link.
Menu Item Type
Toggle
Link Type Availability
Async, AsyncPPP, HDLC-Bridge, MLT, SyncPPP, and X.25
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.12.
2. For 04*Link state, enter 4to select Enabled or Disabled. The default is Enabled.
This example displays 04*Link state set to Disabled.
>4
Menu 4.2.11.12
01 Link Number (1-16)--------------------------------------------------------01
02*Link Type (Async, X25, HDLC, SyncPPP, AsyncPPP, MLT)---------------- Async
03 Link Description------------------------------ Async link 1
04*Link state (Enabled, Disabled)--------------------------------------Disabled
Configuration in the AI296 Local Menu System
1. Access the Link Menu.
2. For Link state, select Up or Down. The default is Down.
6-31
AI296 Version 9.8x User’s Guide
Link Configuration: General Link Properties Configuration
This example displays Link state set to Down.
X.25 Link Menu
Link to configure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Link state . . . . . . . . . . . . . . . . . . . . . . . . . . Up [Down]
Link Type
Description
This menu item defines the type of link as asynchronous, X.25, HDLC, synchronous
more information about link types.
Menu Item Type
Toggle
Link Type Availability
Async, AsyncPPP, HDLC-Bridge, MLT, SyncPPP, and X.25
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.12.
2. For 02*Link Type, enter 2to select Async, X25, HDLC, SyncPPP, AsyncPPP, or MLT. The
default is Async.
This example displays 02*Link Type set to HDLC.
>2
Menu 4.2.11.12
01 Link number (1-16)--------------------------------------------------------01
02*Link Type (Async, X25, HDLC, SyncPPP, AsyncPPP, MLT)----------------
HDLC
Configuration in the AI296 Local Menu System
1. Access the Link Menu.
2. For Link Type, select Async, X25, HDLC, SyncPPP, AsyncPPP, or MLT. The default is Async.
This example displays Link Type set to HDLC-Bridge.
HDLC-Bridge Link Menu
Link to configure . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Link state . . . . . . . . . . . . . . . . . . . . . . . . . . [Up]
Link Type . . Async X.25 [HDLC-Bridge] SyncPPP AsyncPPP
Down
MLT
6-32
AI296 Version 9.8x User’s Guide
Link Configuration: General Link Properties Configuration
Passive Link with Clocking
Description
This menu item enables or disables an X.25 passive link from supplying a clock value
while the link is in the inactive state.
ꢀ
Note: Old AT&T 5ESS interface cards (TN983) require clocking with the passive link
set up.
Menu Item Type
Toggle
Link Type Availability
X.25
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.12.
2. For 13*Passive Link with Clocking, enter 13to select Enabled or Disabled. The
default is Disabled.
This example displays 13*Passive Link with Clocking set to Enabled.
>13
Menu 4.2.11.12
01 Link number (1-16)--------------------------------------------------------05
02*Link Type (Async, X25, HDLC, SyncPPP, AsyncPPP, MLT)----------------
X.25
03 Link Description------------------------------ X.25 link 5
04*Link state (Enabled, Disabled)--------------------------------------Disabled
05*Link mode (Normal, Passive, Extended)------------------------------- Normal
06 Port speed (0 - 128000 bps, 0 is external clocking)-------------------009600
07+X25 LAPB Parameters
08+X25 Parameters
09+Virtual Circuits
10*Hardware Interface (RS232,RS530,V.35)----------------------------------RS232
11+BX25 Configuration
12 Auto Disable Error Limit (0-1000000)---------------------------------0000000
13*Passive Link with Clocking (Enabled, Disabled)---------------------- Enabled
Configuration in the AI296 Local Menu System
1. Access the X.25 Link Menu.
2. From the X.25 Link Menu, select Quick X.25 Menu. The Quick X.25 Menu appears.
3. For Passive Link with Clocking, select Enabled or Disabled. The default is Disabled.
6-33
AI296 Version 9.8x User’s Guide
Link Configuration: General Link Properties Configuration
This example displays Passive Link with Clocking set to Enabled.
\
Quick X.25 Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
05
Interface Mode . . . . . . . . . . . . . . . . . . . . . . .
DTE
[DCE]
Port speed (0=external clocking) . . . . . . . . . . . . . . . . . . . . 9600
X25 Passive Link Mode . . . . . . . . . . . [Normal]
Passive Link with Clocking . . . . . . . . . . . . .
Passive
[Enabled]
Extended
Disabled
Port Data Bits
Description
This menu item defines the number of databits in a data byte.
Menu Item Type
Toggle
Link Type Availability
Async and AsyncPPP
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.12.
2. For 06*Port Data Bits, enter 6to select 7 or 8. The default is 8.
This example displays 06*Port Data Bits set to 7.
>6
Menu 4.2.11.12
01 Link Number (1-16)--------------------------------------------------------01
02*Link Type (Async, X25, HDLC, SyncPPP, AsyncPPP, MLT)---------------- Async
03 Link Description------------------------------ Async link 1
04*Link state (Enabled, Disabled)-------------------------------------- Enabled
05+Port speed------------------------------------------------------------- 9600
06*Port Data Bits (7, 8)------------------------------------------------------7
Configuration in the AI296 Local Menu System
1. Access the Async Link Menu or AsyncPPP Link Menu.
2. For Port data bits, select Seven or Eight. The default is Eight.
6-34
AI296 Version 9.8x User’s Guide
Link Configuration: General Link Properties Configuration
This example displays Port data bits set to Seven.
Async Link Menu
Link to configure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Link state . . . . . . . . . . . . . . . . . . . . . . . . . .
Up
AsyncPPP
RS-530
[Down]
MLT
V.35
Link Type . .
Interface Type . . . . . . . . . . . . . . . . .
Port speed (in bits per second):
[Async]
X.25
HDLC-Bridge
SyncPPP
[RS-232]
300
Autobaud
Port data bits . . . . . . . . . . . . . . . . . . . . . .
1200
2400
4800
[9600]
19.2K
38.4K
57.6K
115.2K
Eight
[Seven]
Port Parity
Description
This menu item defines parity, which is a process for detecting whether or not bits of
data have been altered during data transmission.
Menu Item Type
Toggle
Link Type Availability
Async and AsyncPPP
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.12.
2. For 08*Port Parity, enter 8to select None, Odd, or Even. The default is None.
This example displays 08*Port Parity set to Odd.
>8
Menu 4.2.11.12
01 Link Number (1-16)--------------------------------------------------------01
02*Link Type (Async, X25, HDLC, SyncPPP, AsyncPPP, MLT)---------------- Async
03 Link Description------------------------------ Async link 1
04*Link state (Enabled, Disabled)-------------------------------------- Enabled
05+Port speed------------------------------------------------------------- 9600
06*Port Data Bits (7, 8)------------------------------------------------------8
07*Port Stop Bits (1, 2)------------------------------------------------------1
08*Port Parity (None, Odd, Even)------------------------------------------- Odd
Configuration in the AI296 Local Menu System
1. Access the Async Link Menu or AsyncPPP Link Menu.
2. For Port parity, select None, Even, or Odd. The default is None.
6-35
AI296 Version 9.8x User’s Guide
Link Configuration: General Link Properties Configuration
This example displays Port parity set to Odd.
Async Link Menu
Link to configure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Link state . . . . . . . . . . . . . . . . . . . . . . . . . .
Up
AsyncPPP
RS-530
[Down]
MLT
V.35
Link Type . .
Interface Type . . . . . . . . . . . . . . . . .
Port speed (in bits per second):
[Async]
X.25
HDLC-Bridge
SyncPPP
[RS-232]
300
Autobaud
Port data bits . . . . . . . . . . . . . . . . . . . . . .
Port stop bits . . . . . . . . . . . . . . . . . . . . . . . .
Port parity . . . . . . . . . . . . . . . . . . . . . None
1200
2400
4800
[9600]
19.2K
38.4K
57.6K
115.2K
[Seven]
Eight
[Two]
[Odd]
One
Even
Port Speed
Description
This menu item defines the baud rate for a port.
Menu Item Type
Data in the AI296 local menu system
Link Type Availability
Async, AsyncPPP, HDLC-Bridge, MLT, SyncPPP, and X.25
Configuration in the AI198 Menu System
ꢀ
Note: The menu configuration has two variations based on the type of link being
configured.
To configure the port speed on Async or AsyncPPP links:
1. Access Menu 4.2.11.12.
2. For Port speed, enter the associated item number.
6-36
AI296 Version 9.8x User’s Guide
Link Configuration: General Link Properties Configuration
Menu 4.2.11.12.5 appears.
>5
Menu 4.2.11.12.5
01 300
Baud
02 1200 Baud
03 2400 Baud
04 4800 Baud
05 9600 Baud
06 19200 Baud
07 38400 Baud
08 57600 Baud
09 115200 Baud
10 Auto Baud
ꢀ
Note: 10 Auto Baud is not available for AsyncPPP.
3. Enter a value from 1to 10to select the port speed. Menu 4.2.11.12 reappears with
the new port speed selection.
This example displays 05+Port speed set to 4800.
>4
Menu 4.2.11.12
01 Link Number (1-16)--------------------------------------------------------01
02*Link Type (Async, X25, HDLC, SyncPPP, AsyncPPP, MLT)----------------
Async
03 Link Description------------------------------ Async link 1
04*Link state (Enabled, Disabled)-------------------------------------- Enabled
05+Port speed------------------------------------------------------------- 4800
To configure the port speed on an HDLC-Bridge, MLT, SyncPPP, or X.25 link:
1. Access Menu 4.2.11.12.
2. For Port speed, enter the associated item number, a comma, and the port speed
value.
This example displays 06 Port speed set to 19200.
>6,19200
Menu 4.2.11.12
01 Link number (1-16)--------------------------------------------------------13
02*Link Type (Async, X25, HDLC, SyncPPP, AsyncPPP, MLT)----------------
03 Link Description------------------------------
HDLC
04*Link state (Enabled, Disabled)--------------------------------------Disabled
06 Port speed (0 - 128000 bps, 0 is external clocking)-------------------019200
6-37
AI296 Version 9.8x User’s Guide
Link Configuration: General Link Properties Configuration
Configuration in the AI296 Local Menu System
1. Access the Link Menu.
2. For Port speed, select 300, 1200, 2400, 4800, 9600, 19.2K, 38.4K, 57.6K, 115.2K, or
Autobaud. The default is 9600.
This example displays Port speed set to 4800.
Async Link Menu
Link to configure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Link state . . . . . . . . . . . . . . . . . . . . . . . . . .
Up
AsyncPPP
RS-530
[Down]
MLT
V.35
Link Type . .
Interface Type . . . . . . . . . . . . . . . . .
Port speed (in bits per second):
[Async]
X.25
HDLC-Bridge
SyncPPP
[RS-232]
300 1200
Autobaud
2400
[4800]
9600
19.2K
38.4K
57.6K
115.2K
Port Stop Bits
Description
This menu item defines the number of stop bits. A stop bit is an extra bit at the end of
an asynchronous character that helps the receiver recognize the end of the character.
Menu Item Type
Toggle
Link Type Availability
Async and AsyncPPP
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.12.
2. For 07*Port Stop Bits, enter 7to select 1 or 2. The default is 1.
This example displays 07*Port Stop Bits set to 2.
>7
Menu 4.2.11.12
01 Link Number (1-16)--------------------------------------------------------01
02*Link Type (Async, X25, HDLC, SyncPPP, AsyncPPP, MLT)---------------- Async
03 Link Description------------------------------ Async link 1
04*Link state (Enabled, Disabled)-------------------------------------- Enabled
05+Port speed------------------------------------------------------------- 9600
06*Port Data Bits (7, 8)------------------------------------------------------8
07*Port Stop Bits (1, 2)------------------------------------------------------2
6-38
AI296 Version 9.8x User’s Guide
Link Configuration: General Link Properties Configuration
Configuration in the AI296 Local Menu System
1. Access the Async Link Menu or AsyncPPP Link Menu.
2. For Port stop bits, select One or Two. The default is One.
This example displays Port stop bits set to Two.
Async Link Menu
Link to configure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Link state . . . . . . . . . . . . . . . . . . . . . . . . . .
Up
AsyncPPP
RS-530
[Down]
MLT
V.35
Link Type . .
[Async]
X.25
HDLC-Bridge
SyncPPP
[RS-232]
Interface Type . . . . . . . . . . . . . . . . .
Port speed (in bits per second):
300
Autobaud
Port data bits . . . . . . . . . . . . . . . . . . . . . .
Port stop bits . . . . . . . . . . . . . . . . . . . . . . . .
1200
2400
4800
[9600]
19.2K
38.4K
57.6K
115.2K
[Seven]
Eight
[Two]
One
Sync Port Encoding
Description
This menu item sets the binary encoding on a port.
Menu Item Type
Toggle
Link Type Availability
MLT
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.12.
2. For 07*Sync Port Encoding, enter 7to select NRZ or NRZI. The default is NRZ.
This example displays 07*Sync Port Encoding set to NRZI.
>7
Menu 4.2.11.12
01 Link number (1-16)--------------------------------------------------------01
02*Link Type (Async, X25, HDLC, SyncPPP, AsyncPPP, MLT)---------------- MLT
03 Link Description------------------------------ Async link 1
04*Link state (Enabled, Disabled)-------------------------------------- Enabled
05 Port speed (0 - 128000 bps, 0 is external clocking)-------------------009600
06*Hardware Interface (RS232,RS530,V.35)----------------------------------RS232
07*Sync Port Encoding (NRZ, NRZI)------------------------------------------NRZI
6-39
AI296 Version 9.8x User’s Guide
Link Configuration: General Link Properties Configuration
Configuration in the AI296 Local Menu System
1. Access the MLT Link Menu.
2. For Sync Port Encoding, select NRZ or NRZI. The default is NRZ.
This example displays Sync Port Encoding set to NRZI.
MLT Link Menu
Link to configure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Link state . . . . . . . . . . . . . . . . . . . . . . . . . .
Up
[Down]
[MLT]
V.35
Link Type . .
Async
X.25
HDLC-Bridge
SyncPPP
[RS-232]
AsyncPPP
RS-530
Interface Type . . . . . . . . . . . . . . . . .
Link Description . . . . . . . . . . . . . . ................... X.25 link 5
Interface Mode . . . . . . . . . . . . . . . . . . . . . . .
Port speed (0=external clocking) . . . . . . . . . . . . . . . . . . . . 9600
Sync Port Encoding . . . . . . . . . . . . . . . . . . . . . . NRZ [NRZI]
DTE
[DCE]
Xon Repeat Interval
Description
This menu item enables or disables the XON repeat interval. When enabled, AI296
sends multiple XON characters at the specified interval. Some equipment requires the
receipt of multiple XONs before sending data after it has received an XOFF.
Menu Item Type
Data
Link Type Availability
Aysnc and AsyncPPP
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.12.
2. For 10 Xon Repeat interval, enter 10,and a interval value. The default is 0.
6-40
AI296 Version 9.8x User’s Guide
Link Configuration: General Link Properties Configuration
This example displays 10 Xon Repeat interval set to 30.
>10,30
Menu 4.2.11.12
01 Link Number (1-16)--------------------------------------------------------01
02*Link Type (Async, X25, HDLC, SyncPPP, AsyncPPP, MLT)---------------- Async
03 Link Description------------------------------ Async link 1
04*Link state (Enabled, Disabled)-------------------------------------- Enabled
05+Port speed------------------------------------------------------------- 9600
06*Port Data Bits (7, 8)------------------------------------------------------8
07*Port Stop Bits (1, 2)------------------------------------------------------1
08*Port Parity (None, Odd, Even)-------------------------------------------None
09*Flow Control (None, XonXoff)----------------------------------------- None
10 Xon Repeat interval (0 - 120s with 0 = no repeat)------------------------030
Configuration in the AI296 Local Menu System
1. Access the Async Link Menu or AsyncPPP Link Menu.
2. For XON Repeat Interval, enter a interval value. The default is 0.
This example displays XON Repeat Interval set to 30.
Async Link Menu
Link to configure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Link state . . . . . . . . . . . . . . . . . . . . . . . . . .
Up
AsyncPPP
RS-530
[Down]
MLT
V.35
Link Type . .
[Async]
X.25
HDLC-Bridge
SyncPPP
[RS-232]
Interface Type . . . . . . . . . . . . . . . . .
Port speed (in bits per second):
300
Autobaud
Port data bits . . . . . . . . . . . . . . . . . . . . . .
Port stop bits . . . . . . . . . . . . . . . . . . . . . . . .
1200
2400
[4800]
9600
19.2K
38.4K
57.6K
115.2K
Seven
[Eight]
[Two]
[Odd]
One
Even
Port parity . . . . . . . . . . . . . . . . . . . . .
SW Flow Control . . . . . . . . . . . . . . . . . . . . .
XON Repeat Interval (0 - 120s with 0 = no repeat) . . . . . . . . . . . . 30
None
[None]
XonXoff
6-41
AI296 Version 9.8x User’s Guide
Link Configuration: General PPP Properties Configuration
General PPP Properties Configuration
The following menu items are available for PPP configuration:
z
z
z
IPCP Address Settings
Description
The IPCP address settings are configured using three menu items:
z Local IP address—Defines a valid local IP address for AI296.
z Remote IP address—Defines an IP address for the remote device.
z Subnet mask—Defines a subnet mask for the link.
Menu Item Type
Data
Link Type Availability
AsyncPPP and SyncPPP
Configuration in the AI198 Menu System
1. Do one of the following:
z
z
For an asynchronous PPP link, access Menu 4.2.11.12-2.2.
For a synchronous PPP link, access Menu 4.2.11.12.8.
2. For 01*Network Control Protocol, enter 1to select IPCP. The default is IPCP.
3. For 02 Local IP Address, enter 2,and the IP address. Entering 0.0.0.0 specifies
that the remote device will assign the IP address for AI296. The default is 0.0.0.0.
4. For 03 Remote IP Address, enter 3,and the IP address. Entering 0.0.0.0 specifies
that the remote device will assign its own IP address. The default is 0.0.0.0.
5. For 04 Subnet Mask, enter 4,and the subnet mask. The default is 255.255.255.240.
6-42
AI296 Version 9.8x User’s Guide
Link Configuration: General PPP Properties Configuration
This example displays:
z 01*Network Control Protocol set to IPCP
z 02 Local IP Address set to 099.045.006.033
z 03 Remote IP Address set to 106.046.092.004
z 04 Subnet Mask set to 255.255.255.000.
>4,255.255.255.000
Menu 4.2.11.12.8
01*Network Control Protocol (IPCP, BCP)------------------------------------IPCP
02 Local IP Address---------------------------------------------099.045.006.033
03 Remote IP Address--------------------------------------------106.046.092.004
04 Subnet Mask--------------------------------------------------255.255.255.000
Configuration in the AI296 Local Menu System
1. Access the AsyncPPP or SyncPPP Link Menu.
2. Select PPP Configuration Menu. The PPP Configuration Menu appears.
3. For Local IP address, enter the IP address. Entering 0.0.0.0 specifies that the
remote device will assign the IP address for AI296. The default is 0.0.0.0.
4. For Remote IP address, enter the IP address. Entering 0.0.0.0 specifies that the
remote device will assign its own IP address. The default is 0.0.0.0.
5. For Subnet Mask, enter the subnet mask. The default is 255.255.255.240.
This example displays:
z Local IP address set to 23.230.34.5
z Remote IP address set to 23.230.34.6
z Subnet Mask set to 255.255.255.000.
PPP Configuration Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
3
Network Control Protocol . . . . . . . . . . . . . . . . . .
IPCP Address Parameters
[IPCP]
BCP
Local IP address . . . . . . . . . . . . . . . . . . . . . . ... 23.230.34.5
Remote IP address . . . . . . . . . . . . . . . . . . . . . . ... 23.230.34.6
Subnet Mask . . . . . . . . . . . . . . . . . . . . . . . . . 255.255.255.000
6-43
AI296 Version 9.8x User’s Guide
Link Configuration: General PPP Properties Configuration
Maximum Unit Settings
Description
The maximum unit settings are configured using two menu items:
z Maximum receive unit (MRU)—Defines the maximum number of bytes that can be
received in a single packet.
z Maximum transmit unit (MTU)—Defines the maximum number of bytes that can be
transmitted in a single packet.
ꢀ
Note: During LCP negotiations on a PPP link, AI296 will advertise the MRU
configured by the user. If the peer negotiates its MRU with AI296, then the
MTU on the AI296 side will be set to the peer’s MRU. If the peer does not
negotiate its MRU, then the MTU on the AI296 side will be set to the value
configured by the user.
Menu Item Type
Data
Link Type Availability
AsyncPPP and SyncPPP
Configuration in the AI198 Menu System
1. Do one of the following:
z
z
For an asynchronous PPP link, access Menu 4.2.11.12-2.2.
For a synchronous PPP link, access Menu 4.2.11.12.8.
2. For 05 Maximum Receive Unit, enter 5,and the byte value. The defaults are 1518 for
network control protocol BCP and 1500 for network control protocol IPCP.
3. For 06 Maximum Transmit Unit, enter 6,and the byte value. The defaults are 1518for
network control protocol BCP and 1500 for network control protocol IPCP.
This example displays 05 Maximum Receive Unitset to 1000and 06 Maximum Transmit Unit
set to 900.
>6,900
Menu 4.2.11.12.8
01*Network Control Protocol (IPCP, BCP)------------------------------------ BCP
02 Local IP Address---------------------------------------------000.000.000.000
03 Remote IP Address--------------------------------------------000.000.000.000
04 Subnet Mask--------------------------------------------------255.255.255.240
05 Maximum Receive Unit (128-1568)-----------------------------------------1000
06 Maximum Transmit Unit (64-1600)-----------------------------------------0900
6-44
AI296 Version 9.8x User’s Guide
Link Configuration: General PPP Properties Configuration
Configuration in the AI296 Local Menu System
1. Access the AsyncPPP or SyncPPP Link Menu.
2. Select PPP Configuration Menu. The PPP Configuration Menu appears.
3. For Maximum Receive Unit, enter the byte value. The defaults are 1518 for network
control protocol BCP and 1500 for network control protocol IPCP.
4. For Maximum Transmit Unit, enter the byte value. The defaults are 1518 for network
control protocol BCP and 1500 for network control protocol IPCP.
This example displays Maximum Receive Unitset to 1000and Maximum Transmit Unitset to
900 for an IPCP network control protocol.
PPP Configuration Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
3
Network Control Protocol . . . . . . . . . . . . . . . . . .
IPCP Address Parameters
[IPCP]
BCP
Local IP address . . . . . . . . . . . . . . . . . . . . . . ....... 0.0.0.0
Remote IP address . . . . . . . . . . . . . . . . . . . . . . ....... 0.0.0.0
Subnet Mask . . . . . . . . . . . . . . . . . . . . . . . . . 255.255.255.240
Maximum Receive Unit . . . . . . . . . . . . . . . . . . . . . . . . . . 1000
Maximum Transmit Unit . . . . . . . . . . . . . . . . . . . . . . . . . . 900
Network Control Protocol
Description
This menu item defines the network control protocol as BCP or IPCP. BCP configures,
enables, and disables bridge protocol modules on both ends of a PPP link. IPCP
configures, enables, and disables IP protocol modules on both ends of a PPP link.
Menu Item Type
Toggle
Link Type Availability
AsyncPPP and SyncPPP
6-45
AI296 Version 9.8x User’s Guide
Link Configuration: General PPP Properties Configuration
Configuration in the AI198 Menu System
1. Do one of the following:
z
z
For an asynchronous PPP link, access Menu 4.2.11.12-2.2.
For a synchronous PPP link, access Menu 4.2.11.12.8.
2. For 01*Network Control Protocol, enter 1to select IPCP or BCP. The default is IPCP.
This example displays 01*Network Control Protocol for a synchronous PPP link set to
BCP.
>1
Menu 4.2.11.12.8
01*Network Control Protocol (IPCP, BCP)------------------------------------ BCP
Configuration in the AI296 Local Menu System
1. Access the AsyncPPP Link Menu or SyncPPP Link Menu.
2. Select PPP Configuration Menu. The PPP Configuration Menu appears.
3. For Network Control Protocol, select IPCP or BCP. The default is IPCP.
This example displays Network Control Protocol set to IPCP.
PPP Configuration Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
3
Network Control Protocol . . . . . . . . . . . . . . . . . .
[IPCP]
BCP
6-46
AI296 Version 9.8x User’s Guide
Link Configuration: LAPB Parameters Configuration
LAPB Parameters Configuration
The following settings are used to configure LAPB parameters for an MLT or X.25 link:
z
z
z
z
Frame Settings
Description
Frame settings are configured using three menu items:
z Frame Level Disconnect—Specifies the level at which a disconnect frame is sent.
The following options are available:
z Active—Specifies that a disconnect frame (DISC) is sent and an unnumbered
acknowledgment (UA) must be received to acknowledge that the link is
disconnected. Some systems do not acknowledge the DISC frame with a UA
but send a set asynchronous balanced mode frame (SABM) instead. To bring
this link up, the system must be configured for a passive disconnect. If a
remote system fails to respond to a receive ready (RR) frame enough times to
exceed the maximum number of accepted retransmissions for
unacknowledged frames (described in section N2 Retry Counter on page 6-
50), then AI296 sends DISC frames continuously.
z Passive—Specifies that the DISC frame is not sent. AI296 responds to an
SABM with a UA. If a remote system fails to respond to an RR frame enough
times to exceed the maximum number of accepted retransmissions for
unacknowledged frames, then AI296 sends SABM frames continuously.
z Other—Specifies that an immediate disconnect frame (DISC) is sent if an RR
has been sent enough times to exceed the maximum number of accepted
retransmissions for unacknowledged frames and no reply has been received.
z Frame Window Size—Specifies the number of frames the link can send before
receiving confirmation that the first frame has been received correctly. This means
that data can continue to flow in situations where there may be long turn-around
time lags without stopping to wait for an acknowledgement.
Menu Item Type
Toggle for frame level disconnect
Data for frame window size
6-47
AI296 Version 9.8x User’s Guide
Link Configuration: LAPB Parameters Configuration
Link Type Availability
MLT and X.25
Configuration in the AI198 Menu System
1. Access menu 4.2.11.12.8 for MLT or menu 4.2.11.12.7 for X.25.
2. For 02*Frame level disconnect, enter 2to select Active, Passiveor Other. The default
is Active.
3. For 03 Frame Window size, enter 3,and the window size. The default is 7.
This example displays 02*Frame level disconnect set to Passive and 03 Frame Window
size set to 4.
>3 4
Menu 4.2.11.12.7
01*Interface mode (DTE or DCE)----------------------------------------------DCE
02*Frame level disconnect (Active, Passive, Other)----------------------Passive
03 Frame Window size (1 - 7)--------------------------------------------------4
Configuration in the AI296 Local Menu System
1. Access the MLT or X.25 Link Menu.
2. Select LAPB Menu or X.25 LAPB Menu. The MLT LAPB Menu or X.25 LAPB Menu
appears.
3. For Frame Level Disconnect, select Active, Passive, or Other. The default is Active.
4. For Frame Window Size, enter the window size. The default is 7.
This example displays Frame Level Disconnect set to Passive and Frame Window Size set
to 4.
X.25 LAPB Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
02
Other
Frame Window Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Frame Level Disconnect . . . . . . . . . . .
Active
[Passive]
Interface Mode
Description
This menu item configures the interface mode as either DTE or DCE. DTE is used for
a communications device (typically a terminal or computer) that is the source or
destination of signals on a network. DCE is used for a device (typically the modem)
that establishes, maintains, and terminates a session on a network. It may also
convert signals for transmission.
6-48
AI296 Version 9.8x User’s Guide
Link Configuration: LAPB Parameters Configuration
Menu Item Type
Toggle
Link Type Availability
MLT and X.25
Configuration in the AI198 Menu System
1. Access menu 4.2.11.12.7 for MLT or menu 4.2.11.12.8 for X.25.
2. For 01*Interface mode, enter 1to select DCE or DTE. The default is DCE.
This example displays 01*Interface mode set to DTE.
>1
Menu 4.2.11.12.8
01*Interface mode (DTE or DCE)----------------------------------------------DTE
LAPB Timer Settings
Description
The LAPB timer settings are configured using three menu items:
z T1 ack timer—Defines the maximum amount of time from the end of transmission
to the receipt of an acknowledgment.
z T2 ack delay timer—Defines the time available from the receipt of a frame until a
response has to be transmitted.
z T4 idle timer—Defines the maximum time allowed without the exchange of
frames on a data link.
Menu Item Type
Data
Link Type Availability
MLT and X.25
Configuration in the AI198 Menu System
1. Access menu 4.2.11.12.7 for MLT or menu 4.2.11.12.8 for X.25.
2. For 05 T1 ack timer, enter 5,and the timer value. The default is 3000.
3. For 06 T2 ack delay timer, enter 6,and the timer value. The default is 4000.
4. For 07 T4 idle timer, enter 7,and the timer value. The default is 25000.
6-49
AI296 Version 9.8x User’s Guide
Link Configuration: LAPB Parameters Configuration
This example displays:
z 05 T1 ack timer set to 19000
z 06 T2 ack delay timer set to 20000
z 07 T4 idle timer set to 50000.
>7,50000
Menu 4.2.11.12.8
01*Interface mode (DTE or DCE)----------------------------------------------DCE
02*Frame level disconnect (Active, Passive, Other)---------------------- Active
03 Frame Window size (1 - 7)--------------------------------------------------7
04 N2 retry count (0 - 255)-------------------------------------------------150
05 T1 ack timer (100 - 25500 ms)------------------------------------------19000
06 T2 ack delay timer (100 - 25500 ms)------------------------------------20000
07 T4 idle timer (0 - 200000 ms)-----------------------------------------050000
Configuration in the AI296 Local Menu System
1. Access the MLT or X.25 Link Menu.
2. Select LAPB Menu or X.25 LAPB Menu. The MLT LAPB Menu or X.25 LAPB Menu
appears.
3. For T1 Ack Timer, enter the timer value. The default is 3000.
4. For T2 Ack Delay Timer, enter the timer value. The default is 4000.
5. For T4 Idle Timer, enter the timer value. The default is 25000.
This example displays:
z T1 Ack Timer set to 19000
z T2 Ack Delay Timer set to 20000
z T4 Idle Timer set to 50000.
MLT LAPB Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
03
Frame Level Disconnect . . . . . . . . . . . [Active] Passive Other
Frame Window Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
N2 Retry Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . .150
T1 Ack Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19000
T2 Ack Delay Timer . . . . . . . . . . . . . . . . . . . . . . . . . . .20000
T4 Idle Timer
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 50000
N2 Retry Counter
Description
This menu item defines the maximum number of accepted retransmissions for
unacknowledged frames.
6-50
AI296 Version 9.8x User’s Guide
Link Configuration: LAPB Parameters Configuration
Menu Item Type
Data
Link Type Availability
MLT and X.25
Configuration in the AI198 Menu System
1. Access menu 4.2.11.12.7 for MLT or menu 4.2.11.12.8 for X.25.
2. For 04 N2 retry count, enter 4,and the retry count. The default is 20.
This example displays 04 N2 retry count set to 150.
4,150
Menu 4.2.11.12.8
01*Interface mode (DTE or DCE)----------------------------------------------DCE
02*Frame level disconnect (Active, Passive, Other)---------------------- Active
03 Frame Window size (1 - 7)--------------------------------------------------7
04 N2 retry count (0 - 255)-------------------------------------------------150
Configuration in the AI296 Local Menu System
1. Access the MLT Link Menu.
2. Select LAPB Menu. The MLT LAPB Menu appears.
3. For N2 Retry Counter, enter the retry count. The default is 20.
This example displays N2 Retry Counter set to 150.
MLT LAPB Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
03
Frame Level Disconnect . . . . . . . . . . . [Active] Passive Other
Frame Window Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
N2 Retry Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . .150
6-51
AI296 Version 9.8x User’s Guide
Link Configuration: Modem Option Configuration
Modem Option Configuration
The following menu items are used for modem option configuration. They are
available for asynchronous and asynchronous PPP links:
z
z
z
Modem String
Description
This menu item configures the modem string, which can be any of the following:
z
z
z
The text sent to a port when an associated link starts or restarts following the
termination of a call
The dial string the link to uses to dial the modem automatically once it is
enabled
A command that places the modem in auto answer mode so that it is set to
receive calls
Menu Item Type
Data
Link Type Availability
Async and AsyncPPP
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.12.14.
2. For 01 Modem string, enter 1,and the modem string. Maximum length is 80
characters.
This example displays 01 Modem string set to 6145553003.
>1,6145553003
Menu 4.2.11.12.14
01 Modem string------------------------------------------------------6145553003
6-52
AI296 Version 9.8x User’s Guide
Link Configuration: Modem Option Configuration
Configuration in the AI296 Local Menu System
1. Access the Async Link Menu or AsyncPPP Link Menu.
2. Select Modem Setup Menu. The Modem Setup Menu appears.
3. For Modem string, enter the modem string.
This example displays Modem string set to 6145552002.
Modem Setup Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
3
Modem string . . . . . . . . . . . . .............................. 6145552002
Dialing Time-out Interval
Description
This menu item configures the amount of time in seconds that the modem waits
before redialing a call when connection is not initially established.
Menu Item Type
Data
Link Type Availability
Async and AsyncPPP
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.12.14.
2. For 02 Dialing time-out, enter 2,and the timeout value. The default is 30.
This example displays 02 Dialing time-out set to 10.
>2,10
Menu 4.2.11.12.14
01 Modem string------------------------------------------------------6145553003
02 Dialing time-out (5 - 300 s)---------------------------------------------010
Configuration in the AI296 Local Menu System
1. Access the Async Link Menu or AsyncPPP Link Menu.
2. Select Modem Setup Menu. The Modem Setup Menu appears.
3. For Dialing time-out, enter the time out value. The default is 30.
6-53
AI296 Version 9.8x User’s Guide
Link Configuration: Modem Option Configuration
This example displays Dialing time-out set to 10.
Modem Setup Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
3
Modem string . . . . . . . . . . . . .............................. 6145552002
Dialing time-out (5 - 300 s). . . . . . . . . . . . . . . . . . . . . . . . 10
Number of Dial Attempts
Description
This menu item configures the number of times the modem redials before terminating
a call.
Menu Item Type
Data
Link Type Availability
Async and AsyncPPP
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.12.14.
2. For 03 Number of dial attempts, enter 3,and the number of redial attempts. The
default is 3.
This example displays 03 Number of dial attempts set to 15.
>3,15
Menu 4.2.11.12.14
01 Modem string------------------------------------------------------6145553003
02 Dialing time-out (5 - 300 s)---------------------------------------------010
03 Number of dial attempts (0 - 100, 0 = continuous retry)------------------015
Configuration in the AI296 Local Menu System
1. Access the Async Link Menu or AsyncPPP Link Menu.
2. Select Modem Setup Menu. The Modem Setup Menu appears.
3. For Number of dial attempts, enter the number of redial attempts. The default is 3.
6-54
AI296 Version 9.8x User’s Guide
Link Configuration: Modem Option Configuration
This example displays Number of dial attempts set to 15.
Modem Setup Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
3
Modem string . . . . . . . . . . . . .............................. 6145552002
Dialing time-out (5 - 300 s). . . . . . . . . . . . . . . . . . . . . . . . 10
Number of dial attempts (0 - 100, 0 = continuous retry) . . . . . . . . . . 15
6-55
AI296 Version 9.8x User’s Guide
Link Configuration: PPP Authentication Configuration
PPP Authentication Configuration
The following menu items are available for PPP authentication configuration:
z
z
z
Local Authentication Settings
Description
The local authentication settings are configured using three menu items:
z Local authentication method—Defines the local authentication method as one of
the following options:
z PAP—Specifies the method that uses a two-way handshake that is done only
upon initial link establishment.
z CHAP—Specifies the method that verifies the identity of the peer using a three-
way handshake that is done upon initial link establishment. Verification may
be repeated any time after the link has been established. CHAP also encrypts
the user’s password over the PPP link to provide added security.
z None—Specifies no authentication will be used.
z Local PAP/CHAP identity—Defines the user name for local PAP/CHAP
authentication.
z Local PAP password/CHAP secret—Defines the password for local PAP/CHAP
authentication.
Menu Item Type
Toggle for local authentication method
Data for local PAP/CHAP identity and local PAP password/CHAP secret
Link Type Availability
AsyncPPP and SyncPPP
Configuration in the AI198 Menu System
1. Do one of the following:
z
z
For an asynchronous PPP link, access Menu 4.2.11.12-2.1.
For a synchronous PPP link, access Menu 4.2.11.12.7.
6-56
AI296 Version 9.8x User’s Guide
Link Configuration: PPP Authentication Configuration
2. For 02*Local Authentication Method, enter 2to select None, PAP, or CHAP. The default is
None.
3. For 03 Local PAP/CHAP identity, enter 3,and the user name. Maximum length is 24
characters. The default is applied.
4. For 04 Local PAP Password/CHAP Secret, enter 4,and the password. Maximum
length is 24 characters. The default is applied.
This example displays:
z 02*Local Authentication Method set to PAP
z 03 Local PAP/CHAP identity set to bri24
z 04 Local PAP Password/CHAP Secret set to documentation.
>4,documentation
Menu 4.2.11.12.7
01*RAS Option (DISABLED,RADIUS,RADIUS_FB,TACACS,TACACS_FB)------------ TACACS
02*Local Authentication Method (None, PAP, CHAP)--------------------------- PAP
03 Local PAP/CHAP identity-----------------------------
04 Local PAP Password/CHAP Secret----------------------
bri24
documentation
Configuration in the AI296 Local Menu System
1. Access the AsyncPPP Link Menu or SyncPPP Link Menu.
2. Select PPP Authentication Menu. The PPP Authentication Menu appears.
3. For Local Authentication Method, select None, PAP, or CHAP. The default is None.
4. For Local PAP/CHAP Identity, enter the user name. The default is applied.
5. For Local PAP Password/CHAP Secret, enter the password. The default is applied.
This example displays:
z Local Authentication Method set to CHAP
z Local PAP/CHAP Identity set to bri24
z Local PAP Password/CHAP Secret set to documentation.
PPP Authentication Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
Authentication Options
3
Local Authentication Method . . . . . . . . . . . .
RAS Option:
None
PAP
[CHAP]
Disabled
Local PAP/CHAP Identity . . . . . . . . . . . . . . . . .............. bri24
Local PAP Password/CHAP Secret . . . . . . . . . . . . ...... documentation
RADIUS
[RADIUS/Fallback]
TACACS+
TACACS+/Fallback
6-57
AI296 Version 9.8x User’s Guide
Link Configuration: PPP Authentication Configuration
RAS Option
Description
This menu item configures the method AI296 uses to obtain ID and password
information for a link. The following options are available:
z
Disabling RAS causes AI296 to use local ID and password information to validate
the ID and password sent from a remote device.
z
Enabling RADIUS causes AI296 to use the ID and password information
configured in the RADIUS server to validate the ID and password sent from the
remote device.
z
Enabling RADIUS with fallback causes AI296 to attempt to use the ID and
password information configured in the RADIUS server to validate the ID and
password sent from the remote device. If neither of the RADIUS servers respond,
AI296 uses the local ID and password (configured in the PPP Authentication
Menu) for validation.
z
z
Enabling TACACS+ causes AI296 to use the ID and password information
configured in the TACACS+ server to validate the ID and password sent from the
remote device.
Enabling TACACS+ with fallback causes AI296 to attempt to use the ID and
password information configured in the TACACS+ server to validate the ID and
password sent from the remote device. If neither of the TACACS+ servers
respond, AI296 uses the local ID and password (entered in the PPP
Authentication Menu) for validation.
ꢀ
Notes: When connecting to a remote PPP device, ensure that the PPP
authentication timeout on that device is set to a minimum of 30 seconds. If
the network latency is high, set that value to a higher number of seconds.
ꢀ The TACACS+ server used must support version 1.78 or later of the
TACACS+ protocol.
Menu Item Type
Toggle
Link Type Availability
AsyncPPP and SyncPPP
6-58
AI296 Version 9.8x User’s Guide
Link Configuration: PPP Authentication Configuration
Configuration in the AI198 Menu System
1. Do one of the following:
z
z
For an asynchronous PPP link, access Menu 4.2.11.12-2.1.
For a synchronous PPP link, access Menu 4.2.11.12.7.
2. For 01*RAS Option, enter 1to select DISABLED, RADIUS, RADIUS_FB, TACACS, or TACACS_FB.
The default is DISABLED.
This example displays 01*RAS Option set to TACACS for an asynchronous PPP link.
>1
Menu 4.2.11.12-2.1
TACACS
01*RAS Option (DISABLED,RADIUS,RADIUS_FB,TACACS,TACACS_FB)------------
Configuration in the AI296 Local Menu System
To configure RADIUS PPP authentication:
1. Access the AsyncPPP Link Menu or SyncPPP Link Menu.
2. Select PPP Authentication Menu. The PPP Authentication Menu appears.
3. For RAS Option, select Disabled, RADIUS, RADIUS/Fallback, TACACS+, or TACACS+/Fallback.
The default is Disabled.
This example displays RAS Option set to RADIUS/Fallback.
PPP Authentication Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
Authentication Options
3
Local Authentication Method . . . . . . . . . . . .
RAS Option:
[None]
PAP
CHAP
Disabled
RADIUS
[RADIUS/Fallback]
TACACS+
TACACS+/Fallback
6-59
AI296 Version 9.8x User’s Guide
Link Configuration: PPP Authentication Configuration
Remote Authentication Settings
Description
The remote authentication settings are configured using three menu items:
z Remote authentication method—Defines the remote authentication method as one
of the following options:
z PAP specifies the method that uses a two-way handshake that is done only
upon initial link establishment.
z CHAP specifies the method that verifies the identity of the peer by using a
three-way handshake that is done upon initial link establishment. Verification
may be repeated any time after the link has been established. CHAP also
encrypts the user’s password over the PPP link to provide added security.
z None specifies no authentication will be used.
z Remote PAP/CHAP identity—Defines the user name for remote PAP/CHAP
authentication.
z Remote PAP password/CHAP secret—Defines the password for remote PAP/CHAP
authentication.
Menu Item Type
Toggle for remote authentication method
Data for remote PAP/CHAP identity and remote PAP password/CHAP secret
Link Type Availability
AsyncPPP and SyncPPP
Configuration in the AI198 Menu System
1. Do one of the following:
z
z
For an asynchronous PPP link, access Menu 4.2.11.12-2.1.
For a synchronous PPP link, access Menu 4.2.11.12.7.
2. For 05*Remote Authentication Method, enter 5to select None, PAP, or CHAP. The default
is None.
3. For 06 Remote PAP/CHAP identity, enter 6,and the user name. The default is
applied.
4. For 07 Remote PAP Password/CHAP Secret, enter 7,and the password. The default is
applied.
6-60
AI296 Version 9.8x User’s Guide
Link Configuration: PPP Authentication Configuration
This example displays:
z 05*Remote Authentication Method set to CHAP
z 06 Remote PAP/CHAP identity set to bri24
z 07 Remote PAP Password/CHAP Secret set to documentation.
>7,documentation
Menu 4.2.11.12.7
01*RAS Option (DISABLED,RADIUS,RADIUS_FB,TACACS,TACACS_FB)------------ TACACS
02*Local Authentication Method (None, PAP, CHAP)--------------------------- PAP
03 Local PAP/CHAP identity-----------------------------
04 Local PAP Password/CHAP Secret----------------------
05*Remote Authentication Method (None, PAP, CHAP)--------------------------CHAP
bri24
documentation
06 Remote PAP/CHAP identity----------------------------
07 Remote PAP Password/CHAP Secret---------------------
bri24
documentation
Configuration in the AI296 Local Menu System
1. Access the AsyncPPP or SyncPPP Link Menu.
2. Select PPP Authentication Menu. The PPP Authentication Menu appears.
3. For Remote Authentication Method, select None, PAP, or CHAP. The default is None.
4. For Remote PAP/CHAP Identity, enter the user name. The default is applied.
5. For Remote PAP Password/CHAP Secret, enter the password. The default is applied.
This example displays:
z Remote Authentication Method set to CHAP
z Remote PAP/CHAP Identity set to bri24
z Remote PAP Password/CHAP Secret set to documentation.
PPP Authentication Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
Authentication Options
3
Local Authentication Method . . . . . . . . . . . .
RAS Option:
None
PAP
[CHAP]
Disabled
Local PAP/CHAP Identity . . . . . . . . . . . . . . . . .............. bri24
Local PAP Password/CHAP Secret . . . . . . . . . . . . ...... documentation
RADIUS
[RADIUS/Fallback]
TACACS+
TACACS+/Fallback
Remote Authentication Method . . . . . . . . . . . .
None
PAP
[CHAP]
Remote PAP/CHAP Identity . . . . . . . . . . . . . . . . .............. bri24
Remote PAP Password/CHAP Secret . . . . . . . . . . . . ...... documentation
6-61
AI296 Version 9.8x User’s Guide
Link Configuration: Quick X.25 Configuration
Quick X.25 Configuration
The Quick X.25 configuration menu is available only in the AI296 local menu system.
The following configuration items are available:
z
z
z
z
z
z
z
z
Frame Settings
Description
Frame settings are configured using two menu items:
z Frame level disconnect—Specifies the level at which a disconnect frame is sent.
The following options are available:
z Active—Acknowledges that a link is disconnected when a disconnect frame
(DISC) is sent and an unnumbered acknowledgment (UA) is received. Some
systems do not acknowledge the DISC frame with a UA but send a set
asynchronous balanced mode frame (SABM) instead. To bring this link up, the
system must be configured for a passive disconnect. If a remote system fails
to respond to a receive ready (RR) frame enough times to exceed the
maximum number of accepted retransmissions for unacknowledged frames
DISC frames continuously.
z Passive—Specifies that the DISC frame is not sent. AI296 responds to an
SABM with a UA. If a remote system fails to respond to an RR frame enough
times to exceed the maximum number of accepted retransmissions for
unacknowledged frames, then AI296 sends SABM frames continuously.
z Other—Specifies that an immediate disconnect frame (DISC) is sent if an RR
has been sent enough times to exceed the maximum number of accepted
retransmissions for unacknowledged frames and no reply has been received.
6-62
AI296 Version 9.8x User’s Guide
Link Configuration: Quick X.25 Configuration
z Frame window size—Specifies the number of frames the link can send before
receiving confirmation that the first frame has been received correctly. This means
that data can continue to flow in situations where there may be long turn-around
time lags without stopping to wait for an acknowledgement.
Menu Item Type
Toggle for frame level disconnect
Data for frame window size
Link Type Availability
X.25
Configuration in the AI296 Local Menu System
1. Access the X.25 Link Menu.
2. Select Quick X.25 Menu. The Quick X.25 Menu appears.
3. For Frame Level Disconnect, select Active, Passive, or Other. The default is Active.
4. For Frame Window Size, enter the window size. The default is 7.
This example displays Frame Level Disconnect set to Passive and Frame Window Size set
to 4.
Quick X.25 Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
Interface Mode . . . . . . . . . . . . . . . . . . . . . . . DTE
Port speed (0=external clocking) . . . . . . . . . . . . . . . . . . . . 9600
02
[DCE]
X25 Passive Link Mode . . . . . . . . . . .
Passive Link with Clocking . . . . . . . . . . . . .
Frame Level Disconnect . . . . . . . . . . Active
[Normal]
Passive
Enabled
[Passive]
Extended
[Disabled]
Other
Frame Window Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Interface Mode
Description
This menu item configures the interface mode as either DTE or DCE. DTE is used for
a communications device (typically a terminal or computer) that is the source or
destination of signals on a network. DCE is used for a device (typically the modem)
that establishes, maintains, and terminates a session on a network. It may also
convert signals for transmission.
6-63
AI296 Version 9.8x User’s Guide
Link Configuration: Quick X.25 Configuration
Menu Item Type
Toggle
Link Type Availability
X.25
Configuration in the AI296 Local Menu System
1. Access the X.25 Link Menu.
2. Select Quick X.25 Menu. The Quick X.25 Menu appears.
3. For Interface Mode, select DCE or DTE. The default is DCE.
This example displays Interface Mode set to DTE.
Quick X.25 Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
02
DCE
Interface Mode . . . . . . . . . . . . . . . . . . . . . . .
[DTE]
Number of PVCs
Description
This menu defines the number of PVCs being configured. A PVC is a virtual circuit
that is permanently available. PVCs differ from SVCs in that an SVC must be
reestablished each time data is to be sent. Once the data has been sent, the SVC
disappears. PVCs are more efficient for connections between hosts that communicate
frequently.
Menu Item Type
Data
Link Type Availability
X.25
Configuration in the AI296 Local Menu System
1. Access the X.25 Link Menu.
2. Select Quick X.25 Menu. The Quick X.25 Menu appears.
3. For Number of PVCs, enter the number of PVCs you want to configure. The default is
0.
6-64
AI296 Version 9.8x User’s Guide
Link Configuration: Quick X.25 Configuration
This example displays Number of PVCs set to 12.
Quick X.25 Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
03
Interface Mode . . . . . . . . . . . . . . . . . . . . . . .
Port speed (0=external clocking) . . . . . . . . . . . . . . . . . . . . 4800
DTE
[DCE]
X25 Passive Link Mode . . . . . . . . . . .
Passive Link with Clocking . . . . . . . . . . . . .
Frame Level Disconnect . . . . . . . . . . [Active]
[Normal]
Passive
Enabled
Passive
Extended
[Disabled]
Other
Frame Window Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Max Packet Size . . . . . . . . . . . . . . . . . . . . [128] 256 512
Packet Window Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
X121 Local Address . . . . . . . . . . . . . . . . . . . . . ................
Number of PVCs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Packet Settings
Description
Packet settings are configured using two menu items:
z Max packet size—Defines the maximum number of bytes permitted for an X.25
packet. This limit governs both transmit and receive packets.
z Packet window size—Defines the packet window size, which specifies the number
of packets that can be sent before receiving confirmation that the first packet was
received correctly.
Menu Item Type
Toggle for max packet size
Data for packet window size
Link Type Availability
X.25
Configuration in the AI296 Local Menu System
1. Access the X.25 Link Menu.
2. Select Quick X.25 Menu. The Quick X.25 Menu appears.
3. For Max Packet Size, select 128, 256, or 512. The default is 128.
4. For Packet Window Size, enter the window size. The default is 2.
6-65
AI296 Version 9.8x User’s Guide
Link Configuration: Quick X.25 Configuration
This example displays Max Packet Size set to 256 and Packet Window Size set to 5.
Quick X.25 Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
02
[DCE]
Interface Mode . . . . . . . . . . . . . . . . . . . . . . .
DTE
Port speed (0=external clocking) . . . . . . . . . . . . . . . . . . . . 9600
X25 Passive Link Mode . . . . . . . . . . .
Passive Link with Clocking . . . . . . . . . . . . .
Frame Level Disconnect . . . . . . . . . . [Active]
[Normal]
Passive
Enabled
Passive
Extended
[Disabled]
Other
Frame Window Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Max Packet Size . . . . . . . . . . . . . . . . . . . . 128 [256] 512
Packet Window Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Passive Link Settings
Description
The passive link configuration settings are configured using two menu items:
z X.25 passive link mode—Defines the mode of operation for an X.25 link as one of
the following:
z Normal—Specifies the mode used for normal X.25 service.
z Passive—Specifies the mode that allows AI296 to operate with the SCCS
application of the AT&T 5ESS. The SCCS application requires redundant links
at the 5ESS. These links are called SCC0B and SCC1B. Only one link is
active at a time. The 5ESS constantly tries to bring up whichever link is idle. If
the 5ESS has SCC0B active, it will try to bring up SCC1B. If SCC1B comes
up, the 5ESS will drop SCC0B and send information on SCC1B. Passive
mode ensures that either SCC0B or SCC1B will be up but not simultaneously.
z Extended—Specifies the mode that supports passive link capability to the 5ESS
over a TCP/IP network. Extended mode ensures that either SCC0A or
SCC1A will be up but not simultaneously and will temporarily take down the
corresponding link if connections fail or cannot be placed because the
corresponding remote link is down.
z Passive link with clocking—Enables or disables an X.25 passive link from
supplying a clock value while the link is in the inactive state.
ꢀ
Note: Old AT&T 5ESS interface cards (TN983) require clocking with the passive
link set up.
Menu Item Type
Toggle
6-66
AI296 Version 9.8x User’s Guide
Link Configuration: Quick X.25 Configuration
Link Type Availability
X.25
Configuration in the AI296 Local Menu System
1. Access the X.25 Link Menu.
2. Select Quick X.25 Menu. The Quick X.25 Menu appears.
3. For X25 Passive Link Mode, select Normal, Passive, or Extended. The default is Normal.
4. For Passive Link with Clocking, select Enabled or Disabled. The default is Disabled.
This example displays X25 Passive Link Mode set to Passive and Passive Link with
Clocking set to Enabled.
Quick X.25 Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
Interface Mode . . . . . . . . . . . . . . . . . . . . . . . DTE
Port speed (0=external clocking) . . . . . . . . . . . . . . . . . . . . 9600
02
[DCE]
X25 Passive Link Mode . . . . . . . . . . . Normal
Passive Link with Clocking . . . . . . . . . . . . .
[Passive]
[Enabled]
Extended
Disabled
Port Speed
Description
This menu item defines how many bits of data AI296 can transmit per second over a
link.
ꢀ
Note: There is an aggregate baud rate limitation of 359 kilobits per second for link
groups 1 to 4, 5 to 8, 9 to 12, and 13 to 16. For example, the total baud rate
configured for links 1 to 4 must not exceed 359 kilobits per second. If it does,
then the AI296 disables the links and reports an error.
Menu Item Type
Data
Link Type Availability
X.25
Configuration in the AI296 Local Menu System
1. Access the X.25 Link Menu.
2. Select Quick X.25 Menu. The Quick X.25 Menu appears.
6-67
AI296 Version 9.8x User’s Guide
Link Configuration: Quick X.25 Configuration
3. For Port speed, enter the baud rate. The default is 9600.
This example displays Port speed set to 128000
Quick X.25 Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
02
Interface Mode . . . . . . . . . . . . . . . . . . . . . . .
Port speed (0=external clocking) . . . . . . . . . . . . . . . . . . . 128000
DTE
[DCE]
SVC Settings
Description
SVCs are network connections that are established when transmission is required
and are disconnected when the session is complete. The SVC settings in the Quick
X.25 menu are configured using two menu items:
z SVC low—Defines the minimum LCN used for SVCs.
z SVC high—Defines the maximum LCN used for SVCs.
Menu Item Type
Data
Link Type Availability
X.25
Configuration in the AI296 Local Menu System
1. Access the X.25 Link Menu.
2. Select Quick X.25 Menu. The Quick X.25 Menu appears.
3. For SVC Low, enter the minimum LCN used for SVCs. This number must be higher
than the number of PVCs. The default is 1.
4. For SVC High, enter the maximum LCN used for SVCs. This number must be
higher than the SVC Low value. The default is 1.
6-68
AI296 Version 9.8x User’s Guide
Link Configuration: Quick X.25 Configuration
This example displays SVC Low set to 250 and SVC High set to 3149.
Quick X.25 Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
02
Interface Mode . . . . . . . . . . . . . . . . . . . . . . .
Port speed (0=external clocking) . . . . . . . . . . . . . . . . . . . 128000
DTE
[DCE]
X25 Passive Link Mode . . . . . . . . . . .
Passive Link with Clocking . . . . . . . . . . . . .
Frame Level Disconnect . . . . . . . . . . [Active]
Normal
[Passive]
[Enabled]
Passive
Extended
Disabled
Other
Frame Window Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Max Packet Size . . . . . . . . . . . . . . . . . . . . [128] 256 512
Packet Window Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
X121 Local Address . . . . . . . . . . . . . . . . . . . . . ................
Number of PVCs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 0
+ PVC Menu
SVC Low . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250
SVC High . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3419
X.121 Local Address
Description
This menu item defines the X.121 address used in the X.25 network. The X.121
address consists of a three-digit Data Country Code (DCC) plus a network digit,
together forming the four-digit Data Network Identification Code (DNIC), followed by
the Network Terminal Number (NTN) of at most ten digits.
Menu Item Type
Data
Link Type Availability
X.25
Configuration in the AI296 Local Menu System
1. Access the X.25 Link Menu.
2. Select Quick X.25 Menu. The Quick X.25 Menu appears.
3. For X121 Local Address, enter the value.
6-69
AI296 Version 9.8x User’s Guide
Link Configuration: Quick X.25 Configuration
This example displays X121 Local Address set to 59274.
Quick X.25 Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
02
Interface Mode . . . . . . . . . . . . . . . . . . . . . . .
DTE
Port speed (0=external clocking) . . . . . . . . . . . . . . . . . . . . 9600
[DCE]
X25 Passive Link Mode . . . . . . . . . . .
Passive Link with Clocking . . . . . . . . . . . . .
Frame Level Disconnect . . . . . . . . . . [Active]
[Normal]
Passive
Enabled
Passive
Extended
[Disabled]
Other
Frame Window Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Max Packet Size . . . . . . . . . . . . . . . . . . . . [128] 256 512
Packet Window Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
X121 Local Address . . . . . . . . . . . . . . . . . . . . . .......... 59274
6-70
AI296 Version 9.8x User’s Guide
Link Configuration: RTS/DTR Lead Control Configuration
RTS/DTR Lead Control Configuration
The following configuration items are available for RTS and DTR lead control
configuration:
z
z
DTR State Configuration
Description
DTR is an RS-232 signal sent from a computer or terminal to a modem that indicates
that it (the computer or terminal) is able to accept data. DTR lead control is configured
using two menu items:
z DTR connect state—Sets the DTR connect state to ON or OFF. ON sets DTR to on
while the link is connecting and while it is connected. OFF turns this functionality
off.
z DTR disconnect state—Sets the DTR disconnect state to one of the following
options:
z ON—Sets DTR to on when the link disconnects.
z OFF—Sets DTR to off when the link disconnects.
z TOGGLE—Makes DTR pulse when the link disconnects. The pulse polarity is
opposite to the sense specified for the connected state.
ꢀ
Note: The RTS/DTR lead control options only take effect when the link is configured
as a destination link.
Menu Item Type
Toggle
Link Type Availability
Async and AsyncPPP and SyncPPP
Configuration in the AI198 Menu System
1. For an asynchronous or asynchronous PPP link, access Menu 4.2.11.12.13.
2. For 01*DTR connect state, enter 1to select ON or OFF. The default is ON.
3. For 02*DTR disconnect state, enter 2to select ON, OFF, or TOGGLE. The default is OFF.
6-71
AI296 Version 9.8x User’s Guide
Link Configuration: RTS/DTR Lead Control Configuration
This example displays 01*DTR connect state set to OFF and 02*DTR disconnect state set
to TOGGLE.
>2
Menu 4.2.11.12.13
01*DTR connect state---------------------------------------------------------ON
02*DTR disconnect state (On, Off, Toggle)--------------------------------TOGGLE
Configuration in the AI296 Local Menu System
1. Access the Async Link Menu or AsyncPPP Link Menu.
2. Select RTS/DTR Lead Control Options Menu. The RTS/DTR Lead Control Options
Menu appears.
3. For DTR connect state, select On or Off. The default is On.
4. For DTR disconnect state, select On, Off, or Toggle. The default is Off.
This example displays DTR connect state set to Off and DTR disconnect state set to
Toggle.
RTS/DTR Control Options Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
3
DTR connect state . . . . . . . . . . . . . . . . . . . . . . .
DTR disconnect state . . . . . . . . . . . . . . . . . On
On [Off]
[Toggle]
Off
RTS State Configuration
Description
RTS is an RS-232 signal that is sent from a transmitting terminal to a receiving
terminal to request permission to transmit. It is configured using the following menu
items:
RTS connect state—Sets the RTS connect state to one of the following options:
z On—Sets RTS to on when the link is connecting or connected.
z Off—Sets RTS to off when the link is connecting or connected.
z FlowControl—Enables RTS to follow the hardware flow control convention.
6-72
AI296 Version 9.8x User’s Guide
Link Configuration: RTS/DTR Lead Control Configuration
RTS disconnect state—Sets the RTS disconnect state to one of the following options:
z On—Sets RTS to on when the link disconnects.
z Off—Sets RTS to off when the link disconnects.
z Toggle—Makes RTS pulse when the link disconnects. The pulse polarity is
opposite to the sense specified for the connected state.
Menu Item Type
Toggle
Link Type Availability
Async and AsyncPPP and SyncPPP
Configuration in the AI198 Menu System
1. For an asynchronous or asynchronous PPP link, access menu 4.2.11.12.13.
2. For 03*RTS connect state, enter 3to select ON, OFF, or FLOW CONTROL. The default is ON.
3. For 04*RTS disconnect state, enter 4to select ON, OFF, or TOGGLE. The default is OFF.
This example displays 03*RTS connect state set to FLOW CONTROL and 04*RTS disconnect
state set to TOGGLE.
>4
Menu 4.2.11.12.13
01*DTR connect state---------------------------------------------------------ON
02*DTR disconnect state (On, Off, Toggle)-----------------------------------OFF
03*RTS connect state (On, Off, Flow Control)-----------------------FLOW CONTROL
04*RTS disconnect state (On, Off, Toggle)--------------------------------TOGGLE
Configuration in the AI296 Local Menu System
1. Access the Async Link Menu or AsyncPPP Link Menu.
2. Select RTS/DTR Lead Control Options Menu. The RTS/DTR Lead Control Options
Menu appears.
3. For RTS connect state, select On, Off, or FlowControl. The default is On.
4. For RTS disconnect state, select On, Off, or Toggle. The default is Off.
6-73
AI296 Version 9.8x User’s Guide
Link Configuration: RTS/DTR Lead Control Configuration
This example displays RTS connect stateset to FlowControland RTS disconnect stateset
to Toggle.
RTS/DTR Control Options Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
DTR connect state . . . . . . . . . . . . . . . . . . . . . . . On
3
[Off]
[Toggle]
DTR disconnect state . . . . . . . . . . . . . . . . .
RTS connect state . . . . . . . . . . . . . . . .
RTS disconnect state . . . . . . . . . . . . . . . . .
On
Off
On
Off
On
[FlowControl]
Off [Toggle]
6-74
AI296 Version 9.8x User’s Guide
Link Configuration: X.25 Parameters Configuration
X.25 Parameters Configuration
The following settings are available for X.25 parameter configuration:
z
z
z
z
z
z
z
Maximum Packet Size
Description
This menu item defines the maximum number of bytes permitted for an X.25 packet.
This limit governs both transmit and receive packets.
Menu Item Type
Toggle
Link Type Availability
X.25
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.12.8.
2. For 02*Max packet size, enter 2to select 128, 256, or 512. The default is 128.
This example displays 02*Max packet size set to 512.
>2
Menu 4.2.11.12.8
01*X25 Facilities negotiation----------------------------------------------- ON
02*Max packet size (128, 256, 512)------------------------------------------512
Configuration in the AI296 Local Menu System
1. Access the X.25 Link Menu.
2. Select X.25 Parameters Menu. The X.25 Parameters Menu appears.
3. For Max Packet Size, select 128, 256, or 512. The default is 128.
6-75
AI296 Version 9.8x User’s Guide
Link Configuration: X.25 Parameters Configuration
This example displays Max Packet Size set to 256.
X.25 Parameters Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
03
X25 Facilities Negotiation . . . . . . . . . . . . .
Max Packet Size . . . . . . . . . . . . . . . . . . . .
Enabled
128
[Disabled]
[256] 512
Packet Window Size
Description
This menu item defines the packet window size, which specifies the number of
packets that can be sent before receiving confirmation that the first packet was
received correctly.
Menu Item Type
Data
Link Type Availability
X.25
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.12.8.
2. For 03 Packet window size, enter 3,and the window size. The default is 2.
ꢀ
Note: To access the menu on a Soneplex NE, set Packet window size to 1.
This example displays 03 Packet window size set to 006.
>3,6
Menu 4.2.11.12.8
01*X25 Facilities negotiation----------------------------------------------- ON
02*Max packet size (128, 256, 512)------------------------------------------512
03 Packet window size (1-7)-------------------------------------------------006
Configuration in the AI296 Local Menu System
1. Access the X.25 Link Menu.
2. Select X.25 Parameters Menu. The X.25 Parameters Menu appears.
3. For Packet Window Size, enter the value. The default is 2.
ꢀ
Note: To access the menu on a Soneplex NE, set Packet window size to 1.
6-76
AI296 Version 9.8x User’s Guide
Link Configuration: X.25 Parameters Configuration
This example displays Packet Window Size set to 6.
X.25 Parameters Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
03
X25 Facilities Negotiation . . . . . . . . . . . . .
Max Packet Size . . . . . . . . . . . . . . . . . . . .
Packet Window Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Enabled
128
[Disabled]
[256] 512
Protocol Version
Description
This menu item defines the protocol version (year) for the current link.
Menu Item Type
Toggle
Link Type Availability
X.25
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.12.8.
2. For 17*Protocol version, enter 17to select 1980, 1984, or 1988. The default is 1984.
This example displays 17*Protocol version set to 1988.
>17
Menu 4.2.11.12.8
01*X25 Facilities negotiation-----------------------------------------------OFF
02*Max packet size (128, 256, 512)------------------------------------------128
03 Packet window size (1-7)-------------------------------------------------002
04 X121 local address (0-15 decimal digits)------------------------------------
05 T20 restart timer (0-3200000ms)--------------------------------------1750000
06 T21 call timer (0-3200000ms)-----------------------------------------1000000
07 T22 reset timer (0-3200000ms)----------------------------------------0020000
08 T23 clear timer (0-3200000ms)----------------------------------------0180000
09 T24 window timer (0-3200000ms)---------------------------------------2356000
10 T25 data retransmission timer (0-3200000ms)--------------------------1650000
11 T26 interrupt timer (0-3200000ms)------------------------------------2300000
12 T28 registration timer (0-3200000ms)---------------------------------0090000
13 R20 restart count (0 - 255)----------------------------------------------150
14 R22 reset transmission count (0 - 255)-----------------------------------025
15 R23 clear retransmission count (0 - 255)--------------------------------034
16 R28 registration retransmission count (0 - 255)--------------------------052
17*Protocol version (1980, 1984, 1988)-------------------------------------1988
6-77
AI296 Version 9.8x User’s Guide
Link Configuration: X.25 Parameters Configuration
Configuration in the AI296 Local Menu System
1. Access the X.25 Link Menu.
2. Select X.25 Parameters Menu. The X.25 Parameters Menu appears.
3. For Protocol Version, select 1980, 1984, or 1988. The default is 1984.
This example displays Protocol Version set to 1988.
X.25 Parameters Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
03
X25 Facilities Negotiation . . . . . . . . . . . . .
Max Packet Size . . . . . . . . . . . . . . . . . . . .
Enabled
[128]
[Disabled]
256 512
Packet Window Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
X121 Local Address . . . . . . . . . . . . . . . . . . . . . ................
T20 Restart Timer . . . . . . . . . . . . . . . . . . . . . . . . . . .1750000
T21 Call Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . .1000000
T22 Reset Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 20000
T23 Clear Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180000
T24 Window Timer . . . . . . . . . . . . . . . . . . . . . . . . . . .2356000
T25 Data Retransmission Timer . . . . . . . . . . . . . . . . . . . . .1650000
T26 Interrupt Timer . . . . . . . . . . . . . . . . . . . . . . . . . .2300000
T28 Registration Timer . . . . . . . . . . . . . . . . . . . . . . . .. 90000
R20 Restart Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . .150
R22 Reset Transmission Counter . . . . . . . . . . . . . . . . . . . . . . 25
R23 Clear Transmission Counter . . . . . . . . . . . . . . . . . . . . . . 34
R28 Registration Transmission Counter . . . . . . . . . . . . . . . . . . . 52
Protocol Version . . . . . . . . . . . . . . . . .
1980
1984
[1988]
X.25 Counter Settings
Description
The X.25 counter settings are configured using four menu items:
z R20 restart counter—Defines the maximum number of times a reset can be sent
without receiving reset confirmation.
z R22 reset transmission counter—Defines the maximum number of times a reset
can be sent without receiving clear confirmation.
z R23 clear transmission counter—Defines the maximum number of times a clear
request can be sent without clearing confirmation.
z R28 registration transmission counter—Defines the maximum number of times a
registration request can be sent without receiving registration confirmation.
Menu Item Type
Data
6-78
AI296 Version 9.8x User’s Guide
Link Configuration: X.25 Parameters Configuration
Link Type Availability
X.25
Configuration in the AI198 Menu System
1. Access menu 4.2.11.12.8.
2. For 13 R20 restart count, enter 13,and the counter value. The default is 1.
3. For 14 R22 reset transmission count, enter 14,and the counter value. The default
is 1.
4. For 15 R23 clear retransmission count, enter 15,and the counter value. The
default is 1.
5. For 16 R28 registration retransmission count, enter 16,and the counter value. The
default is 1.
This example displays:
z 13 R20 restart count set to 150
z 14 R22 reset transmission count set to 25
z 15 R23 clear retransmission count set to 34
z 16 R28 registration retransmission count set to 52.
>16,52
Menu 4.2.11.12.8
01*X25 Facilities negotiation-----------------------------------------------OFF
02*Max packet size (128, 256, 512)------------------------------------------128
03 Packet window size (1-7)-------------------------------------------------002
04 X121 local address (0-15 decimal digits)------------------------------------
05 T20 restart timer (0-3200000ms)--------------------------------------1750000
06 T21 call timer (0-3200000ms)-----------------------------------------1000000
07 T22 reset timer (0-3200000ms)----------------------------------------0020000
08 T23 clear timer (0-3200000ms)----------------------------------------0180000
09 T24 window timer (0-3200000ms)---------------------------------------2356000
10 T25 data retransmission timer (0-3200000ms)--------------------------1650000
11 T26 interrupt timer (0-3200000ms)------------------------------------2300000
12 T28 registration timer (0-3200000ms)---------------------------------0090000
13 R20 restart count (0 - 255)----------------------------------------------150
14 R22 reset transmission count (0 - 255)-----------------------------------025
15 R23 clear retransmission count (0 - 255)--------------------------------034
16 R28 registration retransmission count (0 - 255)--------------------------052
Configuration in the AI296 Local Menu System
1. Access the X.25 Link Menu.
2. Select X.25 Parameters Menu. The X.25 Parameters Menu appears.
3. For R20 restart count, enter the counter value. The default is 1.
4. For R22 reset transmission count, enter the counter value. The default is 1.
5. For R23 clear retransmission count, enter the counter value. The default is 1.
6-79
AI296 Version 9.8x User’s Guide
Link Configuration: X.25 Parameters Configuration
6. For R28 registration retransmission count, enter the counter value. The default
is 1.
This example displays:
z R20 restart count set to 150
z R22 reset transmission count set to 25
z R23 clear retransmission count set to 34
z R28 registration retransmission count set to 52.
X.25 Parameters Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
03
X25 Facilities Negotiation . . . . . . . . . . . . .
Max Packet Size . . . . . . . . . . . . . . . . . . . .
Enabled
[128]
[Disabled]
256 512
Packet Window Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
X121 Local Address . . . . . . . . . . . . . . . . . . . . . ................
T20 Restart Timer . . . . . . . . . . . . . . . . . . . . . . . . . . .1750000
T21 Call Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . .1000000
T22 Reset Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 20000
T23 Clear Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180000
T24 Window Timer . . . . . . . . . . . . . . . . . . . . . . . . . . .2356000
T25 Data Retransmission Timer . . . . . . . . . . . . . . . . . . . . .1650000
T26 Interrupt Timer . . . . . . . . . . . . . . . . . . . . . . . . . .2300000
T28 Registration Timer . . . . . . . . . . . . . . . . . . . . . . . .. 90000
R20 Restart Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . .150
R22 Reset Transmission Counter . . . . . . . . . . . . . . . . . . . . . . 25
R23 Clear Transmission Counter . . . . . . . . . . . . . . . . . . . . . . 34
R28 Registration Transmission Counter . . . . . . . . . . . . . . . . . . . 52
X.25 Facilities Negotiation
Description
This menu item allows the window size and packet size to be negotiated between
connections when one end is set differently than the other. When enabled, AI296
initiates negotiation. When disabled, AI296 does not initiate negotiation, but does
respond to negotiation attempts made by the remote side.
Menu Item Type
Toggle
Link Type Availability
X.25
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.12.8.
2. For 01*X25 Facilities negotiation, enter 1to select ON or OFF. The default is OFF.
6-80
AI296 Version 9.8x User’s Guide
Link Configuration: X.25 Parameters Configuration
This example displays 01*X25 Facilities negotiation set to ON.
>1
Menu 4.2.11.12.8
01*X25 Facilities negotiation----------------------------------------------- ON
Configuration in the AI296 Local Menu System
1. Access the X.25 Link Menu.
2. Select X.25 Parameters Menu. The X.25 Parameters Menu appears.
3. For X25 Facilities Negotiation, select Enabled or Disabled. The default is Disabled.
This example displays X25 Facilities Negotiation set to Enabled.
X.25 Parameters Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
03
X25 Facilities Negotiation . . . . . . . . . . . . . [Enabled] Disabled
X.25 Timer Settings
Description
The X.25 timer settings are configured using eight menu items:
z T20 restart timer—Defines the amount of time allowed for receipt of a restart
confirmation or restart indication after a restart request.
z T21 call timer—Defines the amount of time allowed for receipt of call connected,
clear indication, or incoming after a call request.
z T22 reset timer—Defines the amount of time allowed for receipt of a reset
confirmation or reset indication after a reset request.
z T23 clear timer—Defines the amount of time allowed for receipt of a clear
confirmation or clear indication after a restart request.
z T24 window timer—Defines the amount of time allowed for window status
transmission.
z T25 data retransmission timer—Defines the amount of time allowed for T25 data
retransmission.
z T26 interrupt timer—Defines the amount of time allowed for receipt of an interrupt
confirmation after an interrupt is sent.
z T28 registration timer—Defines the amount of time allowed for receipt of a
registration confirmation after a registration request.
6-81
AI296 Version 9.8x User’s Guide
Link Configuration: X.25 Parameters Configuration
Menu Item Type
Data
Link Type Availability
X.25
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.12.8.
2. For 05 T20 restart timer, enter 5,and the timer value. The default is 180000.
3. For 06 T21 call timer, enter 6,and the timer value. The default is 200000.
4. For 07 T22 reset timer, enter 7,and the timer value. The default is 10000.
5. For 08 T23 clear timer, enter 8,and the timer value. The default is 180000.
6. For 09 T24 window timer, enter 9,and the timer value. The default is 75000.
7. For 10 T25 data retransmission timer, enter 10,and the timer value. The default is
150000.
8. For 11 T26 interrupt timer, enter 11,and the timer value. The default is 180000.
9. For 12 T28 registration timer, enter 12,and the timer value. The default is 180000.
This example displays:
z 05 T20 restart timer set to 1750000
z 06 T21 call timer set to 1000000
z 07 T22 reset timer set to 20000
z 08 T23 clear timer set to 180000
z 09 T24 window timer set to 2356000
z 10 T25 data retransmission timer set to 1650000
z 11 T26 interrupt timer set to 2300000
z 12 T28 registration timer set to 90000.
>12,90000
Menu 4.2.11.12.8
01*X25 Facilities negotiation-----------------------------------------------OFF
02*Max packet size (128, 256, 512)------------------------------------------128
03 Packet window size (1-7)-------------------------------------------------002
04 X121 local address (0-15 decimal digits)------------------------------------
05 T20 restart timer (0-3200000ms)--------------------------------------1750000
06 T21 call timer (0-3200000ms)-----------------------------------------1000000
07 T22 reset timer (0-3200000ms)----------------------------------------0020000
08 T23 clear timer (0-3200000ms)----------------------------------------0180000
09 T24 window timer (0-3200000ms)---------------------------------------2356000
10 T25 data retransmission timer (0-3200000ms)--------------------------1650000
11 T26 interrupt timer (0-3200000ms)------------------------------------2300000
12 T28 registration timer (0-3200000ms)---------------------------------0090000
6-82
AI296 Version 9.8x User’s Guide
Link Configuration: X.25 Parameters Configuration
Configuration in the AI296 Local Menu System
1. Access the X.25 Link Menu.
2. Select X.25 Parameters Menu. The X.25 Parameters Menu appears.
3. For T20 Restart Timer, enter the timer value. The default is 180000.
4. For T21 Call Timer, enter the timer value. The default is 200000.
5. For T22 Reset Timer, enter the timer value. The default is 10000.
6. For T23 Clear Timer, enter the timer value. The default is 180000.
7. For T24 Window Timer, enter the timer value. The default is 75000.
8. For T25 Data Retransmission Timer, enter the timer value. The default is 150000.
9. For T26 Interrupt Timer, enter the timer value. The default is 180000.
10. For T28 Registration Timer, enter the timer value. The default is 180000.
This example displays:
z T20 Restart Timer set to 1750000
z T21 Call Timer set to 1000000
z T22 Reset Timer set to 20000
z T23 Clear Timer set to 180000
z T24 Window Timer set to 2356000
z T25 Data Retransmission Timer set to 1650000
z T26 Interrupt Timer set to 2300000
z T28 Registration Timer set to 90000.
X.25 Parameters Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
03
X25 Facilities Negotiation . . . . . . . . . . . . .
Max Packet Size . . . . . . . . . . . . . . . . . . . .
Enabled
[128]
[Disabled]
256 512
Packet Window Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
X121 Local Address . . . . . . . . . . . . . . . . . . . . . ................
T20 Restart Timer . . . . . . . . . . . . . . . . . . . . . . . . . . .1750000
T21 Call Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . .1000000
T22 Reset Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 20000
T23 Clear Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180000
T24 Window Timer . . . . . . . . . . . . . . . . . . . . . . . . . . .2356000
T25 Data Retransmission Timer . . . . . . . . . . . . . . . . . . . . .1650000
T26 Interrupt Timer . . . . . . . . . . . . . . . . . . . . . . . . . .2300000
T28 Registration Timer . . . . . . . . . . . . . . . . . . . . . . . .. 90000
6-83
AI296 Version 9.8x User’s Guide
Link Configuration: X.25 Parameters Configuration
X.121 Local Address
Description
This menu item defines the X.121 address used in the X.25 network. The X.121
address consists of a three-digit Data Country Code (DCC) plus a network digit,
together forming the four-digit Data Network Identification Code (DNIC), followed by
the Network Terminal Number (NTN) of at most ten digits.
Menu Item Type
Data
Link Type Availability
X.25
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.12.8.
2. For 04 X121 local address, enter 4,and the local address value.
This example displays 04 X121 local address set to 43729.
>4,43729
Menu 4.2.11.12.8
01*X25 Facilities negotiation----------------------------------------------- ON
02*Max packet size (128, 256, 512)------------------------------------------512
03 Packet window size (1-7)-------------------------------------------------006
04 X121 local address (0-15 decimal digits)-------------------------------43729
Configuration in the AI296 Local Menu System
1. Access the X.25 Link Menu.
2. Select X.25 Parameters Menu. The X.25 Parameters Menu appears.
3. For X121 Local Address, enter the local address value.
This example displays X121 Local Address set to 59274.
X.25 Parameters Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
03
X25 Facilities Negotiation . . . . . . . . . . . . .
Max Packet Size . . . . . . . . . . . . . . . . . . . .
Enabled
128
[Disabled]
[256] 512
Packet Window Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
X121 Local Address . . . . . . . . . . . . . . . . . . . . . .......... 59274
6-84
AI296 Version 9.8x User’s Guide
Link Configuration: Virtual Circuit Configuration
Virtual Circuit Configuration
The following settings are available for X.25 parameter configuration:
z
z
z
Number of PVCs
Description
This menu defines the number of PVCs being configured. A PVC is a virtual circuit
that is permanently available. PVCs differ from SVCs in that an SVC must be
reestablished each time data is to be sent. Once the data has been sent, the SVC
disappears. PVCs are more efficient for connections between hosts that communicate
frequently.
Menu Item Type
Data
Link Type Availability
X.25
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.12.9.
2. For 01 Number of PVCs, enter 1,and the number of PVCs. The default is 0.
This example displays 01 Number of PVCs set to 15.
>1,15
Menu 4.2.11.12.9
01 Number of PVCs (0 - 1024)-----------------------------------------------0015
Configuration in the AI296 Local Menu System
1. Access the X.25 Link Menu.
2. Select Quick X.25 Menu. The Quick X.25 Menu appears.
3. For Number of PVCs, enter the number of PVCs . The default is 0.
6-85
AI296 Version 9.8x User’s Guide
Link Configuration: Virtual Circuit Configuration
This example displays Number of PVCs set to 12.
Quick X.25 Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
Interface Mode . . . . . . . . . . . . . . . . . . . . . . . DTE
Port speed (0=external clocking) . . . . . . . . . . . . . . . . . . . . 4800
03
[DCE]
X25 Passive Link Mode . . . . . . . . . . .
Passive Link with Clocking . . . . . . . . . . . . .
Frame Level Disconnect . . . . . . . . . . [Active]
[Normal]
Passive
Enabled
Passive
Extended
[Disabled]
Other
Frame Window Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Max Packet Size . . . . . . . . . . . . . . . . . . . . [128] 256 512
Packet Window Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
X121 Local Address . . . . . . . . . . . . . . . . . . . . . ................
Number of PVCs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
PVC Configuration Settings
Description
PVCs are configured using four menu items:
z PVC type—Defines the PVC type as Active, Connect on activity, or Passive.
z Active—Specifies that the PVC attempts to connect as soon as a link goes up.
If an immediate connection is not made, the PVC continues trying to connect
at a specified time interval. This time interval is established by the call timer
setting.
z Connect on activity—Specifies that the PVC connects when data is received.
This PVC remains dormant until it receives a data packet from the network.
z Passive—Specifies that PVCs make no attempt to connect.
z LCN low—Defines the minimum logical channel number for the PVCs you want to
configure.
z LCN high—Defines the maximum logical channel number for the PVCs you want to
configure.
z Timer interval—Defines the timer interval. The timer interval type depends on the
PVC type. The following timer intervals are available:
z Call timer interval—Defines the time interval (in seconds) at which an active
PVC will attempt to establish a connection to a destination.
z Inactivity timer interval—Defines the amount of time (in seconds) after a
connect on activity PVC is started before an inactive call is dropped or
disconnected.
6-86
AI296 Version 9.8x User’s Guide
Link Configuration: Virtual Circuit Configuration
z Reset timer interval—Defines the time interval (in seconds) at which a
passive PVC can remain inactive before AI296 resets it. Since passive PVCs
do not get reset based on a timer, the only configurable value for this setting is
0. The reset timer interval is only configurable in the AI296 menu system.
Menu Item Type
Toggle for PVC type
Data for LCN low, LCN high, and the timer interval
Link Type Availability
X.25
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.12.9.2. This menu displays a summary of all the configured
PVCs for an X.25 link on AI296.
>2
Menu 4.2.11.12.9.2
PVC Type LCN Range
CallTmr
ResetTmr
InActTmr
02+
03+
04+
05+
06+
07+
08+
09+
10+
11+
12+
13+
14+
15+
17 Display first page
18 Next Page
19 Delete entry
20 Save the changes made
21 Exit this menu with no changes
Enter item number and optional ",value" then push <CR> key
>
6-87
AI296 Version 9.8x User’s Guide
Link Configuration: Virtual Circuit Configuration
2. Enter a value (02 through 15) associated with the PVC to be configured. Menu
4.2.11.12.9.2.1 (the PVC Edit Menu) appears.
>3
Menu 4.2.11.12.9.2.1
01*PVC Type (Passive, Active, Connect on activity)----------------------Passive
02 LCN Low (* for all LCNs for the link)-----------------------------------0001
03 LCN High----------------------------------------------------------------0001
04 RESET Timer Interval (seconds)-----------------------------------------00000
20 Save the changes made
21 Exit this menu with no changes
Enter item number and optional ",value" then push <CR> key
>
3. For 01*PVC Type, enter 1to select Passive, Active, or Connect on activity. The default
is Passive.
4. For 02 LCN Low, enter 2,and the minimum LCN value. Valid values are 1 to 1024.
The default is 1.
ꢀ
Note: An asterisk (*) configures all LCNs for the link with values defined in menu
item 4.2.1114.12.9.1.
5. For 03 LCN High, enter 3,and the maximum LCN value. Valid values are 1 to 1024.
The default is 1.
6. For 04 RESET Timer Interval, enter 4,and the reset timer interval value.
The timer type, range, and default settings depend on the PVC type. Refer to
Table 6-1 for PVC types, timer types, ranges, and defaults.
Table 6-1 PVC and Timer Type
PVC Type
Timer Type
Range
Default
Active
Call Timer
30 to 600 s
1 to 600 s
30 s
1 s
Connect on Activity
Inactivity Timer
6-88
AI296 Version 9.8x User’s Guide
Link Configuration: Virtual Circuit Configuration
Table 6-1 PVC and Timer Type (Continued)
PVC Type
Timer Type
Range
Default
Passive
Reset Timer
0 s
0 s
This example displays:
z 01*PVC Type set to Connect
z 02 LCN Low set to 5
z 03 LCN High set to 15
z 04 INACTIVITY Timer Interval set to 240.
>4,240
Menu 4.2.11.12.9.2.1
01*PVC Type (Passive, Active, Connect on activity)----------------------Connect
02 LCN Low (* for all LCNs for the link)-----------------------------------0005
03 LCN High----------------------------------------------------------------0015
04 INACTIVITY Timer Interval (seconds)------------------------------------00240
Configuration in the AI296 Local Menu System
1. Access the X.25 Link Menu.
2. Select Quick X.25 Menu. The Quick X.25 Menu appears.
3. For Number of PVCs, enter the number of PVCs to be configured. The default is 0.
4. For SVC Low, enter a minimum SVC value that is higher than the number of PVCs.
Valid values are from 0 to 4095. The default is 1.
5. For SVC High, enter a maximum SVC value that is higher than the minimum SVC
value. Valid values are from 0 to 4095. The default is 1.
6. Save your work.
7. From the Quick X.25 Menu, select PVC Menu. The PVC Summary Menu appears.
8. For Edit PVC, enter the number of the PVC to be edited. This value must be in the
range of configured PVCs. The PVC Edit Menu appears.
9. For Low PVC, enter the minimum PVC value.
10. For High PVC, enter the maximum PVC value.
11. For PVC Type, select Passive, Active, or ConnectOnActivity. The default is Passive.
12. For Timer Value, select the timer interval value.
6-89
AI296 Version 9.8x User’s Guide
Link Configuration: Virtual Circuit Configuration
The timer type, range, and default settings depend on the PVC type. Refer to
Table 6-2 for PVC types, timer types, ranges, and defaults.
Table 6-2 PVC and Timer Type
PVC Type
Timer Type
Range
Default
Active
Call Timer
30 to 600 s
1 to 600 s
0 s
30 s
1 s
Connect on Activity
Passive
Inactivity Timer
Reset Timer
0 s
This example displays:
z Low PVC set to 30
z High PVC set to 50
z PVC Type set to Active
z Timer Value set to 230.
PVC Edit Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . . .
03
Low PVC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 30
High PVC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 50
PVC Type . . . . . . . . . . . . .
Timer Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230
Passive
[Active]
ConnectOnActivity
SVC Configuration Settings
Description
SVCs are network connections that are established when transmission is required
and are disconnected when the session is complete. The SVC settings are configured
using the following menu items:
z Incoming only SVC low—Defines the minimum LCN used for incoming only SVCs.
z Incoming only SVC high—Defines the maximum LCN used for incoming only SVCs.
z Two-way SVC low—Defines the minimum LCN used for an SVC.
z Two-way SVC high—Defines the maximum LCN used for an SVC.
z Outgoing only SVC low—Defines the minimum LCN used for outgoing only SVCs.
AI296 can place calls on outgoing only SVCs greater than the maximum PVC
and/or two-way SVC.
z Outgoing only SVC high—Defines the maximum LCN used for outgoing only SVCs.
AI296 can place calls on outgoing only SVCs.
6-90
AI296 Version 9.8x User’s Guide
Link Configuration: Virtual Circuit Configuration
Menu Item Type
Data
Link Type Availability
X.25
Configuration in the AI198 Menu System
1. Access Menu 4.2.11.12.9.
2. For 03 Incoming only SVC low, enter 3,and the minimum LCN used for incoming
only SVCs. The default is 0.
3. For 04 Incoming only SVC high, enter 4,and the maximum LCN used for incoming
only SVCs. The default is 0.
Important: AI296 can only receive calls on incoming only SVCs that are greater
than the maximum PVC.
4. For 05 Two-way SVC low, enter 5,and the minimum LCN used for an SVC. The
default is 1.
Important: This value must be greater than the number of PVCs and/or
incoming SVCs.
5. For 06 Two-way SVC high, enter 6,and the maximum LCN used for an SVC. The
default is 1.
6. For 07 Outgoing only SVC low, enter 7,and the minimum LCN used for outgoing
only SVCs. The default is 0.
7. For 08 Outgoing only SVC high, enter 8,and the maximum LCN used for outgoing
only SVCs. The default is 0.
Important: AI296 can place calls on outgoing only SVCs greater than the
maximum PVC and/or two-way SVC.
6-91
AI296 Version 9.8x User’s Guide
Link Configuration: Virtual Circuit Configuration
This example displays:
z 03 Incoming only SVC low set to 8
z 04 Incoming only SVC high set to 64
z 05 Two-way SVC low set to 75
z 06 Two-way SVC high set to 85
z 07 Outgoing only SVC low set to 100
z 08 Outgoing only SVC high set to 150.
>8,150
Menu 4.2.11.12.9
01 Number of PVCs (0 - 1024)-----------------------------------------------0005
02+PVC configuration
03 Incoming only SVC low (0 - 4095)----------------------------------------0008
04 Incoming only SVC high (0 - 4095)---------------------------------------0064
05 Two-way SVC low (0 - 4095)----------------------------------------------0075
06 Two-way SVC high (0 - 4095)---------------------------------------------0085
07 Outgoing only SVC low (0 - 4095)----------------------------------------0100
08 Outgoing only SVC high (0 - 4095)---------------------------------------0150
Configuration in the AI296 Local Menu System
1. Access the X.25 Link Menu.
2. Select Quick X.25 Menu. The Quick X.25 Menu appears.
3. For SVC Low, enter a minimum SVC value that is higher than the number of PVCs.
The default is 1.
4. For SVC High, enter a maximum SVC value that is higher than the minimum SVC
value. The default is 1.
This example displays SVC Low set to 10 and SVC High set to 15.
Quick X.25 Menu
Link being configured . . . . . . . . . . . . . . . . . . . . . . . . .
Interface Mode . . . . . . . . . . . . . . . . . . . . . . . DTE
Port speed (0=external clocking) . . . . . . . . . . . . . . . . . . . . 4800
03
[DCE]
X25 Passive Link Mode . . . . . . . . . . .
Passive Link with Clocking . . . . . . . . . . . . .
Frame Level Disconnect . . . . . . . . . . [Active]
[Normal]
Passive
Enabled
Passive
Extended
[Disabled]
Other
Frame Window Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Max Packet Size . . . . . . . . . . . . . . . . . . . . [128] 256 512
Packet Window Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
X121 Local Address . . . . . . . . . . . . . . . . . . . . . ................
Number of PVCs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
+ PVC Menu
SVC Low . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
SVC High . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
6-92
AI296 Version 9.8x User’s Guide
TID Multiplexing: Overview
Overview
AI296 supports TID multiplexing, which enables a single call from an OSS to fan out
into multiple calls to various NEs. The initiating call may be X.25, asynchronous, or
illustration of TID multiplexing.
TID1
TID2
TID3
Sonet NEs
TID1
TID2
TID3
TID1
TID2
TID3
TID4
TID5
TID6
X.25 Packet Switched
Network
AI296
OSS
TID4
TID5
TID6
TID4
TID5
Sonet NEs
TID6
Figure 7-1 TID Multiplexing Overview
various NEs by means of the TID in the TL1 command. Similarly, AI296 receives TL1
responses and NE reporting messages from several NEs and routes these messages
to the appropriate OSS. The call to AI296 from the OSS is a parent call. The calls
from AI296 to the various NEs are children calls.
After receiving a TL1 command from the OSS, AI296 checks to see if there is an
existing connection for each TID. If a connection to the appropriate NE is already
established, then AI296 forwards the TL1 command to the NE as specified by the TID.
The following characteristics apply to AI296 when it attempts to connect to an NE:
z
z
z
If AI296 is unable to establish a connection to an NE, it will buffer the TL1
command and try to reconnect within 2 seconds.
AI296 tries to connect up to three times if it cannot immediately establish a
connection.
AI296 buffers only one TL1 command for each NE. If a connection is made, AI296
forwards the buffered command to the NE.
7-2
AI296 Version 9.8x User’s Guide
TID Multiplexing: Overview
z
z
If a connection is not established after four tries or if AI296 receives a TL1
command with an unknown TID, the TL1 command gets discarded and a
message gets logged.
If the OSS is disconnected from AI296, all associated children calls to the NEs are
disconnected.
Tip: To access the configuration menu on a Soneplex NE device, you must set the
Packet Window Size to 1.
7-3
AI296 Version 9.8x User’s Guide
TID Multiplexing: TID Multiplexing Configuration
TID Multiplexing Configuration
Establish TID multiplexing by configuring aliases for calls that will go through AI296.
Configure a parent alias to accept the incoming call from the OSS. After doing this,
configure children aliases to route calls to the various network elements. For more
Configuring the Parent Alias
ꢀ
Note: Kentrox recommends that you do not use connect-on-activity PVCs to
establish a parent connection.
Configuration in the AI198 Menu System
1. Log in to AI198.
2. At the prompt, enter menuto access the Main Menu.
3. For 08+Configure the alias translation table, enter 8. The alias configuration
menu appears.
>8
Menu 8
01 Alias name -****************************************************************
02+Simple alias translation
03 Destination -
04 Called address -
05 This alias is visible in the destination menu-----------------------------NO
06 Link number is (1..16) -
07 Caller's address -
08 Call data -
09 App. string -
10 Called protocol -
11 Caller's protocol -
12 Alternate routing alias -
14+Test macros
15 Show entire alias
16 Show the first entry in the alias translation table
17 Show the previous entry in the alias translation table
18 Show the next entry in the alias translation table
19+Delete the above alias translation entry
20 Save the changes made (20b: to the beginning, 20e: to the end)
21 Exit this menu with no changes
Enter item number and optional ",value" then push <CR> key
>
4. For 01 Alias name, enter the alias name for the call coming from the OSS.
7-4
AI296 Version 9.8x User’s Guide
TID Multiplexing: TID Multiplexing Configuration
5. For 02+Simple alias translation, enter 2. Menu 8.2 appears with the available
translation options.
>2
Menu 8.2
01 Simple alias translation
02 Multiplexed connection
03 Multiplexed only translation
04 SLC routing translation
21 Exit this menu with no changes
Enter item number and optional ",value" then push <CR> key
>
6. For 04 SLC routing translation, enter 4. Menu 8 reappears with SLC routing
translation selected for menu item 2.
7. If you are using single alias translation, for 03 Destination, enter 3,and the IP
address of AI296.
8. For 08 Call data, enter 8,and the parent name.
ꢀ
Note: When creating the parent name, note that you use the parent name to
make the children alias names. For example, if a parent is named
PARENT1, valid child names would be PARENT1.1 and PARENT1.2.
9. For 09 App. string, enter:
TMUXn [ TID:tid_for_AI296 ]
n
Defines the maximum number of children connections. Valid
values are 1 to 128.
tid_for_AI296
Defines the terminal identifier for AI296.
10. For 10 Called protocol, enter 10,=""
11. (optional) For 11 Caller's protocol, enter 11,and the caller's protocol.
12. Save your changes.
7-5
AI296 Version 9.8x User’s Guide
TID Multiplexing: TID Multiplexing Configuration
Configuration in the AI296 Local Menu System
ꢀ
Note: To configure aliases in the AI296 local menu system, AI296 must be in
standalone mode.
1. Log in to the AI296 Main Menu.
2. From the AI296 Main Menu, select Alias Menu. The Alias Summary Menu appears.
3. From the Alias Summary Menu, select Add Alias. The Alias Edit Menu appears.
Alias Edit Menu
Alias Name . . . . .
Destination . . . . .......................................................
Caller's Address . . .......................................................
Called Address . . . .......................................................
Call Data . . . . . .......................................................
Caller's Protocol . .......................................................
Called Protocol . . .......................................................
Application String . .......................................................
Alternate Route . . .......................................................
Description . . . . .......................................................
Display Alias in Destination Menu . . . . . . . . . . . . . .
Alias Location . . . . . . . . . . . . . . . . . . .
[Yes]
No
[End]
Beginning
+ Alias Test Menu
Range: {255 characters}
<Ctrl-R> Return to Main Menu
<F1> Help <F2> Send
<F4> Close
4. For Alias Name, enter the alias name for the call coming from the OSS.
5. If you are using single alias translation, for Destination, enter the IP address of
AI296. By entering a destination value, you are specifying the use of single alias
translation.
6. For Call data, enter the parent name.
ꢀ
Note: When creating the parent name, note that you use the parent name to
make the children alias names. For example, if a parent is named
PARENT1, valid child names would be PARENT1.1 and PARENT1.2.
7-6
AI296 Version 9.8x User’s Guide
TID Multiplexing: TID Multiplexing Configuration
7. For Application string, enter:
TMUXn [ TID:tid_for_AI296 ]
n
Defines the maximum number of children connections. Valid
values are 1 to 128.
tid_for_AI296
Defines the terminal identifier for AI296.
8. For Called protocol, enter ="".
9. (optional) For Caller's protocol, enter the caller's protocol.
10. Save your changes.
Configuring the Children Aliases
Configuration in the AI198 Menu System
AI296 supports a maximum of 512 child connections. These connections can be X.25,
asynchronous, or TCP/IP.
To configure the child aliases:
1. Log into AI198.
2. At the prompt, enter menuto access the Main Menu.
3. For 08+Configure the alias translation table, enter 8. The alias configuration
menu appears.
>8
Menu 8
01 Alias name -****************************************************************
02+Simple alias translation
03 Destination -
04 Called address -
05 This alias is visible in the destination menu-----------------------------NO
06 Link number is (1..16) -
07 Caller's address -
08 Call data -
09 App. string -
10 Called protocol -
11 Caller's protocol -
12 Alternate routing alias -
14+Test macros
15 Show entire alias
16 Show the first entry in the alias translation table
17 Show the previous entry in the alias translation table
18 Show the next entry in the alias translation table
19+Delete the above alias translation entry
20 Save the changes made (20b: to the beginning, 20e: to the end)
21 Exit this menu with no changes
Enter item number and optional ",value" then push <CR> key
>
7-7
AI296 Version 9.8x User’s Guide
TID Multiplexing: TID Multiplexing Configuration
4. For 01 Alias name, enter:
parent_name.m
parent_name
Defines the name you entered for 08 Call dataduring the parent
alias configuration.
m
Defines the child number. Valid values are 1 to n(specified
during the parent alias configuration).
5. For 02+Simple alias translation, enter 2. Menu 8.2 appears with the available
translation options.
>2
Menu 8.2
01 Simple alias translation
02 Multiplexed connection
03 Multiplexed only translation
04 SLC routing translation
21 Exit this menu with no changes
Enter item number and optional ",value" then push <CR> key
>
6. For 04 SLC routing translation, enter 4. Menu 8 re-appears with SLC routing
translation selected for menu item 2.
7. If you are using single alias translation, for 03 Destination, enter 3,and the IP
address of AI296. By entering a destination value, you are specifying the use of
single alias translation.
8. For 04 Called address, enter 4,and the called address.
9. For 07 Caller's address, enter 7,and the caller's address.
10. For 08 Call data, enter 8,and the call data information.
7-8
AI296 Version 9.8x User’s Guide
TID Multiplexing: TID Multiplexing Configuration
11. For 09 App. string, enter:
TID:tid
tid
Defines the TID of the destination NE. Maximum length is 20 characters.
12. (optional) For 10 Called protocol, enter 10,and the called protocol.
13. For 11 Caller's protocol, enter 11,="".
Configuration in the AI296 Local Menu System
ꢀ
Note: To configure aliases in the AI296 local menu system, AI296 must be in
standalone mode.
1. Log in to the AI296 Main Menu.
2. From the AI296 Main Menu, select Alias Menu. The Alias Summary Menu appears.
3. From the Alias Summary Menu, select Add Alias. The Alias Edit Menu appears.
Alias Edit Menu
Alias Name . . . . .
Destination . . . . .......................................................
Caller's Address . . .......................................................
Called Address . . . .......................................................
Call Data . . . . . .......................................................
Caller's Protocol . .......................................................
Called Protocol . . .......................................................
Application String . .......................................................
Alternate Route . . .......................................................
Description . . . . .......................................................
Display Alias in Destination Menu . . . . . . . . . . . . . .
Alias Location . . . . . . . . . . . . . . . . . . .
[Yes]
No
[End]
Beginning
+ Alias Test Menu
Range: {255 characters}
<Ctrl-R> Return to Main Menu
<F1> Help <F2> Send
<F4> Close
7-9
AI296 Version 9.8x User’s Guide
TID Multiplexing: TID Multiplexing Configuration
4. For Alias name, enter:
parent_name.m
parent_name
Defines the name you entered for 08 Call dataduring the parent
alias configuration.
m
Defines the child number. Valid values are 1 to n(specified
during the parent alias configuration).
5. If you are using single alias translation, for Destination, enter the IP address of
AI296. By entering a destination value, you are specifying the use of single alias
translation.
6. For Called address, enter the called address.
7. For Caller's address, enter the caller's address.
8. For Call Data, enter the call data information.
9. For Application String, enter:
TID:tid
tid
Defines the TID of the destination NE. Maximum length is 20 characters.
10. (optional) For Called protocol, enter the called protocol.
11. For Caller's protocol, enter ="".
12. Save your changes.
Example Configurations
The following screens display parent and child alias configurations that do the
following:
1. A call comes in on alias 172.16.1.123 at port 1000 (172.16.1.123#1000).
2. The call fans out into two child calls. 09 App. string in the parent alias
configuration determines the number of children; in this case, it is noted by TMUX2.
The children have the following names: TL1DM.1 and TL1DM.2. These names are
established through 08 Call data in the parent alias configuration. The calls to the
first child will be X.25 through link 1 with X.121 address 123456789012
(X25.1.123456789012). The call to the second child will be X.25 through link 2 with
X.121 address 987654321098 (X25.2.987654321098).
7-10
AI296 Version 9.8x User’s Guide
TID Multiplexing: TID Multiplexing Configuration
3. AI296 forwards all TL1 commands with TIDs NE-OH-COLUMBUS-1, NE-OH-COLUMBUS-2,
and NE-OH-COLUMBUS-3 through the first child connection. It forwards all TL1
commands with TIDs NE-OH-WORTHINGTON-1 and NE-OH-WORTHINGTON-2 through the
second child connection.
This example displays the parent alias configuration in the AI198 menu system.
>11 TL1
Menu 8
01 Alias name -------------------------------------------------172.16.1.23#1000
02+Simple alias translation
03 Destination -
04 Called address -
05 This alias is visible in the destination menu----------------------------YES
06 Link number is (1..16) -
07 Caller's address -
08 Call data -------------------------------------------------------------TL1DM
09 App. string -----------------------------------------------------------TMUX2
10 Called protocol ---------------------------------------------------------=""
11 Caller's protocol -------------------------------------------------------TL1
12 Alternate routing alias -
14+Test macros
15 Show entire alias
16 Show the first entry in the alias translation table
17 Show the previous entry in the alias translation table
18 Show the next entry in the alias translation table
19+Delete the above alias translation entry
20 Save the changes made (20b: to the beginning, 20e: to the end)
21 Exit this menu with no changes
Enter item number and optional ",value" then push <CR> key
>
7-11
AI296 Version 9.8x User’s Guide
TID Multiplexing: TID Multiplexing Configuration
This example displays the parent alias configuration in the AI296 menu system.
ꢀ
Note: To configure aliases in the AI296 local menu system, AI296 must be in
standalone mode.
Alias Edit Menu
Alias Name . . . . . ...................................... 172.16.1.23#1000
Destination . . . . .......................................................
Caller's Address . . .......................................................
Called Address . . . .......................................................
Call Data . . . . . ................................................. TL1DM
Caller's Protocol . ................................................... TL1
Called Protocol . . ................................................... =""
Application String . ................................................. TMUX2
Alternate Route . .
Description . . . . .......................................................
Display Alias in Destination Menu . . . . . . . . . . . . . .
Alias Location . . . . . . . . . . . . . . . . . . .
[Yes]
No
[End]
Beginning
+ Alias Test Menu
Range: {255 characters}
<Ctrl-R> Return to Main Menu
<F1> Help <F2> Send
<F4> Close
7-12
AI296 Version 9.8x User’s Guide
TID Multiplexing: TID Multiplexing Configuration
These examples display two of the child alias configurations in the AI198 menu
system.
>11 =""
Menu 8
01 Alias name ----------------------------------------------------------TL1DM.1
02+Simple alias translation
03 Destination -
04 Called address -------------------------------------------X25.1.123456789012
05 This alias is visible in the destination menu----------------------------YES
06 Link number is (1..16) -
07 Caller's address -
08 Call data -
09 App. string --TID:NE-OH-COLUMBUS-1 TID:NE-OH-COLUMBUS-2 TID:NE-OH-COLUMBUS-3
10 Called protocol -
11 Caller's protocol -------------------------------------------------------=""
12 Alternate routing alias -
14+Test macros
15 Show entire alias
16 Show the first entry in the alias translation table
17 Show the previous entry in the alias translation table
18 Show the next entry in the alias translation table
19+Delete the above alias translation entry
20 Save the changes made (20b: to the beginning, 20e: to the end)
21 Exit this menu with no changes
Enter item number and optional ",value" then push <CR> key
>
>11 =""
Menu 8
01 Alias name ----------------------------------------------------------TL1DM.2
02+Simple alias translation
03 Destination -
04 Called address -------------------------------------------X25.2.987654321098
05 This alias is visible in the destination menu----------------------------YES
06 Link number is (1..16) -
07 Caller's address -
08 Call data -
09 App. string -----------------TID:NE-OH-WORTHINGTON-1 TID:NE-OH-WORTHINGTON-2
10 Called protocol -
11 Caller's protocol -------------------------------------------------------=""
12 Alternate routing alias -
14+Test macros
15 Show entire alias
16 Show the first entry in the alias translation table
17 Show the previous entry in the alias translation table
18 Show the next entry in the alias translation table
19+Delete the above alias translation entry
20 Save the changes made (20b: to the beginning, 20e: to the end)
21 Exit this menu with no changes
Enter item number and optional ",value" then push <CR> key
>
7-13
AI296 Version 9.8x User’s Guide
TID Multiplexing: TID Multiplexing Configuration
These examples display two of the child alias configurations in the AI296 menu
system.
ꢀ
Note: To configure aliases in the AI296 local menu system, AI296 must be in
standalone mode.
Alias Edit Menu
Alias Name . . . . . ............................................... TL1DM.1
Destination . . . . .......................................................
Caller's Address . . .......................................................
Called Address . . . .................................... X25.1.123456789012
Call Data . . . . . .......................................................
Caller's Protocol . ................................................... =""
Called Protocol . . .......................................................
Application String . TID:NE-OH-COLUMBUS-1 TID:NE-OH-COLUMBUS-2 TID:NE-OH-COL
Alternate Route . . .......................................................
Description . . . . .......................................................
Display Alias in Destination Menu . . . . . . . . . . . . . .
+ Alias Test Menu
[Yes]
No
<F1> Help <F2> Send
<F4> Close
<Ctrl-R> Return to Main Menu
Alias Edit Menu
Alias Name . . . . . ............................................... TL1DM.2
Destination . . . . .......................................................
Caller's Address . . .......................................................
Called Address . . . .................................... X25.2.987654321098
Call Data . . . . . .......................................................
Caller's Protocol . ................................................... =""
Called Protocol . . .......................................................
Application String . ....... TID:NE-OH-WORTHINGTON-1 TID:NE-OH-WORTHINGTON-2
Alternate Route . .
Description . . . . .......................................................
Display Alias in Destination Menu . . . . . . . . . . . . . .
+ Alias Test Menu
[Yes]
No
Range: {255 characters}
<Ctrl-R> Return to Main Menu
<F1> Help <F2> Send
<F4> Close
7-14
AI296 Version 9.8x User’s Guide
TID Multiplexing: TID Multiplexing Troubleshooting
TID Multiplexing Troubleshooting
If an OSS is not getting a response from an NE, it can send a TL1 retrieve header
command (RTRV-HDR) to determine if the problem is with the NE or with AI296. The
parent connection on AI296 responds to RTRV-HDRcommands that have the same TID
as the one configured for the card.
Tip: For more information regarding TL1 commands, responses, and formats, refer
to the Belcore document GR-833-CORE.
RTRV-HDR
This command is used primarily as an aliveness check.
Format
RTRV-HDR:[ tid ]::ctag;
Parameters
tid
Defines the TID for AI296. Note that the TID and SID are the same.
ctag
Defines the correlation tag used to correlate responses to input commands.
Each input command has a unique ctag. Maximum length is 6 characters.
Responses include the identical ctag.
Normal Response Format
This example displays the format of the response that appears when RTRV-HDRis
successfully executed:
<cr><lf><lf>
<sp><sp><sp><SID><sp><YY-MM-DD><sp><HH:MM:SS><cr><lf>
M<sp><sp><ctag><sp>COMPLD<cr><lf>;
Table 7-1 describes each of the items in the above response format.
Table 7-1 RTRV-HDR Response Format Description
Response Item Description
cr
Specifies a carriage return.
Specifies a line feed.
lf
sp
SID
Specifies a space.
Specifies a system identifier (system ID).
7-15
AI296 Version 9.8x User’s Guide
TID Multiplexing: TID Multiplexing Troubleshooting
Table 7-1 RTRV-HDR Response Format Description (Continued)
Response Item Description
YY-MM-DD
HH:MM:SS
ctag
Specifies the date.
Specifies the time of day.
Specifies the correlation tag.
COMPLD
Specifies completion. The Input requirement is satisfied.
Normal Response Example
This example displays the response that appears when RTRV-HDR:AI232:12345;is
executed.
AI296 97-01-01 05:06:39
M 12345 COMPLD;
Error Response Format
If AI296 receives TL1 commands other than RTRV-HDRwith the same card TID, it
responds with a deny message. This example displays the deny message format.
<cr><lf><lf>
<sp><sp><sp><SID><sp><YY-MM-DD><sp><HH:MM:SS><cr><lf>
M<sp><sp><ctag><sp>DENY<cr><lf>
<sp><sp><sp><errcde><cr><lf>;
Table 7-2 describes each of the items in the above response format.
Table 7-2 Error Response Format Description
Response Item Description
cr
Specifies a carriage return.
Specifies a line feed.
lf
sp
Specifies a space.
SID
Specifies a system identifier (system ID).
Specifies the date.
YY-MM-DD
HH:MM:SS
ctag
Specifies the time of day.
Specifies the correlation tag.
Specifies that the input requirement is not satisfied.
DENY
7-16
AI296 Version 9.8x User’s Guide
TID Multiplexing: TID Multiplexing Troubleshooting
Table 7-2 Error Response Format Description (Continued)
Response Item Description
errcde Specifies the error code.
Error Response Example
This example displays the response that appears if RTRV-HDRfails.
AI296 97-01-01 05:06:39
M 12345 DENY
IIAC;
Diagnostics for TID Multiplexing
To view information on TID multiplexed calls and the associated TIDs, use
diag-tconn. This command displays a list of all connections on the card in the same
format as diag-conn. However, diag-tconnis not interactive.
Use this command either from the AI296 shell or through AI198 as a winslc
7-17
AI296 Version 9.8x User’s Guide
TID Multiplexing: TID Multiplexing Troubleshooting
7-18
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Overview
Overview
AI296 uses aliases to route calls across the backplane of AIswitch. Each incoming
call’s routing information must match an entry in the alias table, or else the call is
rejected. When AI296 is in switch mode, the alias table is stored on AI198. When
AI296 is in standalone mode, the alias table is stored in AI296’s local memory. For
more information about alias translation and macros, see sections Call Routing on
Figure 8-1 displays a typical call processing data flow scenario where AI296 is used.
AI296 Card A
IP address
172.16.30.100
AI296 Card B
IP address
AEPN
172.16.30.200
AEPN
X.25
TCP
Incoming
X.25
call
Outgoing
TCP/IP
call
TCP
X.25
Incoming
Outgoing
TCP/IP
call
X25 call to
X25.2.67891
Figure 8-1 Call Data Flow
over the IRB and be sent out AI296 card B. Refer to the figure to follow the flow of the
call.
The following events occur if the data flow is from left to right:
for information about X.25
2. The data travels upstream and is converted into a TCP call.
3. The data starts downstream through the AEPN protocol option to preserve the
protocol.
4. The data is sent out AI296 card A over TCP on the IRB.
8-2
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Overview
5. The TCP packet is received by AI296 card B.
6. The data travels upstream through the AEPN protocol option to preserve
packetization.
7. The data packet is converted, travels downstream, and is transmitted out AI296
using an X.25 protocol with the original packetizing characteristics preserved.
This is an example configuration in the AI198 menu system for AI296 A:
>8
Menu 8
01 Alias name ----------------------------------------------------------TOCARDB
02+Simple alias translation
03 Destination -
04 Called address ------------------------------------------172.16.30.200 #5000
05 This alias is visible in the destination menu-----------------------------NO
06 Link number is (1..16) -
07 Caller's address -
08 Call data -
09 App. string -
10 Called protocol --------------------------------------------------------AEPN
11 Caller's protocol -------------------------------------------------------=""
12 Alternate routing alias -
14+Test macros
15 Show entire alias
16 Show the first entry in the alias translation table
17 Show the previous entry in the alias translation table
18 Show the next entry in the alias translation table
19+Delete the above alias translation entry
20 Save the changes made (20b: to the beginning, 20e: to the end)
21 Exit this menu with no changes
Enter item number and optional ",value" then push <CR> key
>
8-3
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Overview
This is an example configuration in the AI198 menu system for AI296 B:
>8
Menu 8
01 Alias name -----------------------------------------------172.16.30.200#5000
02+Simple alias translation
03 Destination -
04 Called address --------------------------------------------------X25.2.67891
05 This alias is visible in the destination menu----------------------------YES
06 Link number is (1..16) -
07 Caller's address -
08 Call data -
09 App. string -
10 Called protocol -
11 Caller's protocol ------------------------------------------------------AEPN
12 Alternate routing alias -
14+Test macros
15 Show entire alias
16 Show the first entry in the alias translation table
17 Show the previous entry in the alias translation table
18 Show the next entry in the alias translation table
19+Delete the above alias translation entry
20 Save the changes made (20b: to the beginning, 20e: to the end)
21 Exit this menu with no changes
Enter item number and optional ",value" then push <CR> key
>
8-4
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Call Routing
Call Routing
To route calls with AI296, you must configure an alias for a source and destination
protocol.
ꢀ
Note: Aliases created in AI198 are not visible to AI296 when it is running in
standalone mode. However, you can configure aliases in the AI296 local menu
system when it is in standalone mode.
Configuring an Alias in the AI198 Menu System
ꢀ
Note: Specific configuration information about menu items in the following procedure
is located in section Source/Destination Protocol Tables for the AI198 Menu
To configure an alias in the AI198 Menu System:
1. Log in to AI198.
2. At the prompt, type menu. The main menu appears.
3. To access menu 08+Configure the alias translation table, enter 8. Menu 8 appears:
>8
Menu 8
01 Alias name -****************************************************************
02+Simple alias translation
03 Destination -
04 Called address -
05 This alias is visible in the destination menu-----------------------------NO
06 Link number is (1..16) -
07 Caller's address -
08 Call data -
09 App. string -
10 Called protocol -
11 Caller's protocol -
12 Alternate routing alias -
14+Test macros
15 Show entire alias
16 Show the first entry in the alias translation table
17 Show the previous entry in the alias translation table
18 Show the next entry in the alias translation table
19+Delete the above alias translation entry
20 Save the changes made (20b: to the beginning, 20e: to the end)
21 Exit this menu with no changes
Enter item number and optional ",value" then push <CR> key
>
4. For 01 Alias name -, enter 1,followed by the alias name for the incoming (source)
call.
AI198 translates the alias name into a call of the type defined in the remaining
alias menu items.
8-5
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Call Routing
ꢀ
Note: The alias name may include leading, trailing, or embedded wildcard
matching characters. You may enter an asterisk (*) which replaces zero or
more characters, a question mark (?) which replaces one character, or an
alias macro that starts with an equal sign (=).
For information on acceptable alias naming elements and conventions, refer to
8-12.
5. To access menu 02+Simple alias translation, enter 2. Menu 8.2 appears:
>2
Menu 8.2
01 Simple alias translation
02 Multiplexed connection
03 Multiplexed only translation
04 SLC routing translation
21 Exit this menu with no changes
Enter item number and optional ",value" then push <CR> key
>
6. To select 04 SLC routing translation, enter 4. Menu 8 reappears with the SLC
routing translation configuration items.
Important: Menu item 04 SLC routing translation is the only valid menu item for
AI296. Use SLC routing translations to route calls through cards that
support non-time division subchannel (TDS) connections.
7. (optional) If you are routing calls between two AI296 cards, enter 3,and the IP
address of the remote AI296.
8. For 04 Called address -, enter 4,and the the called (destination) address.
The called (destination) address defines the phone number being called.
Maximum length is 14 characters. The actual address or an alias macro can be
entered here.
8-6
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Call Routing
9. For 05 This alias is visible in the destination menu, enter 5to toggle between Yes
and No.
This setting specifies if the alias will appear in the welcome screen.
10. (optional) For 08 Call data -, enter 8,and the call user data.
Call data is dependent on the type of SLC being used. It may be directly entered
as an alias macro.
11. (optional) For 10 Called protocol -, enter 10,and the called protocol type.
For more information about protocol types, refer to Protocol Processing Modules
12. (optional) For 11 Caller's protocol -, enter 11,and the caller’s protocol type.
For more information about protocol types, refer to Protocol Processing Modules
13. For 20 Save the changes made, enter 20to save the alias configuration.
14. Repeat this procedure for additional alias configurations.
Configuring an Alias in the AI296 Menu System
ꢀ
Note: Specific configuration information about menu items in the following procedure
is located in section Source/Destination Protocol Tables for the AI296 Menu
To configure an alias in the AI296 Menu System:
1. Log in to AI296.
2. At the prompt, type menu. The AI296 Main Menu appears.
3. Access the Alias Menu. The Alias Summary Menu appears.
8-7
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Call Routing
4. From the the Alias Summary Menu, select [Add Alias]. The Alias Edit Menu
appears:
Alias Edit Menu
Alias Name . . . . .
Destination . . . . .......................................................
Caller's Address . . .......................................................
Called Address . . . .......................................................
Call Data . . . . . .......................................................
Caller's Protocol . .......................................................
Called Protocol . . .......................................................
Application String . .......................................................
Alternate Route . . .......................................................
Description . . . . .......................................................
Display Alias in Destination Menu . . . . . . . . . . . . . .
Alias Location . . . . . . . . . . . . . . . . . . .
[Yes]
No
[End]
Beginning
+ Alias Test Menu
Range: {255 characters}
<Ctrl-R> Return to Main Menu
<F1> Help <F2> Send
<F4> Close
5. For Alias Name, enter the alias name for the incoming (source) call.
AI296 translates the alias name into a call of the type defined in the remaining
alias menu items.
ꢀ
Note: The alias name may include leading, trailing, or embedded wildcard
matching characters. You may enter an asterisk (*) which replaces zero or
more characters, a question mark (?) which replaces one character, or an
alias macro that starts with an equal sign (=).
For information on acceptable alias naming elements and conventions, refer to
8-20.
6. (optional) If you are routing calls between two AI296 cards, enter the IP address
of the remote AI296 in the destination field.
7. (optional) For Called Address, enter the called (destination) address.
The called (destination) address defines the phone number being called.
Maximum length is 14 characters. The actual address or an alias macro can be
entered here.
8-8
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Call Routing
8. (optional) For Call Data, enter the call user data.
Call data is dependent on the type of SLC being used. It may be directly entered
as an alias macro.
9. (optional) For Caller's Protocol, enter the caller’s protocol type.
For more information about protocol types, refer to Protocol Processing Modules
10. (optional) For Called Protocol, enter the called protocol type.
For more information about protocol types, refer to Protocol Processing Modules
11. For Display Alias in Destination Menu, select Yes or No.
This setting specifies if the alias will appear in the welcome screen.
12. For Alias Location, select Beginningor Endto place the alias at the beginning or end
of the alias table.
13. Select <F2> Send to save the changes.
14. Repeat this procedure for additional alias configurations.
Arranging Aliases in the Alias Table
To arrange aliases in the alias table:
1. From the AI296 Main Menu, access the Alias Menu. The Alias Summary Menu
appears:
Alias Summary Menu
Find alias:
[Add Alias]
[Sort]
+ alias4
+ alias2
+ alias1
+ alias3
[Move] [Delete]
[Move] [Delete]
[Move] [Delete]
[Move] [Delete]
Range: {255 characters}
<Ctrl-R> Return to Main Menu
<F1> Help
<F4> Close
8-9
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Call Routing
2. From the Alias Summary Menu, select one of the following options:
z
z
Select Sort to sort the aliases alphabetically.
Select Movenext to the desired alias and move it to the top or bottom of the list,
or up or down in the list.
3. Select <F4> Close to exit the Alias Summary Menu.
Configuring an Alias with X.25 Keep-Alive
Some devices will go to sleep if no data is received within a certain timeframe. You
can prevent that by sending a receive-ready (RR) frame periodically on a virtual circuit
(VC). You can customize the time period by configuring the application string of the
Alias menu.
1. Access the Alias Edit Menu. (For information about accessing the Alias Edit
Alias Edit Menu
Alias Name . . . . . .............................................. X.25.4.1
Destination . . . . .......................................................
Caller's Address . . .......................................................
Called Address . . . .......................................... 10.39.3.89#7
Call Data . . . . . .......................................................
Caller's Protocol . .......................................................
Called Protocol . . .......................................................
Application String . ........................................... X25KA -s 20
Alternate Route . .
Description . . . . .......................................................
Display Alias in Destination Menu . . . . . . . . . . . . . .
Alias Test Menu
[Yes]
No
Range: {255 characters}
<Ctrl-R> Return to Main Menu
<F1> Help <F2> Send
<F4> Close
8-10
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Call Routing
2. In the Alias Edit Menu, select Application String and enter the X-25 keep-alive
string as follows:
X25KA [-s | -d] period
where:
X25KA
Notifies the 296 that this is the X-25 keep-alive feature.
period
The period between each RR on the VC. This value is in tenths of
second. In the example above, an RR would be sent every 2
seconds.
-d, -s -
If the -dflag is given, the destination will send out the RRs if it is an
X.25 link. If the -sflag is given, then only the source side of the
connection will send out the RRs if it is an X.25 link. If neither is
given, then it will send out RRs on the side that is an X.25 link and
both if both are X.25 links.
8-11
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Source/Destination Protocol Tables
Source/Destination Protocol Tables
The following parameters are referred to in the tables:
call_data
Defines the call data. Maximum length is 16 characters.
called_address
caller_address
ip_address
Defines the address being called. Maximum length is 14
characters.
Defines the address of the caller. Maximum length is 14
characters.
Defines the IP address in dotted decimal format. The #symbol
must be entered as a field separator between the ip_address
field and the tcp_port_numberfield.
lcn
Defines the logical channel number.
Defines the number of the serial link.
link_number
tcp_port_number
Defines the TCP port number. Valid values are from 1 to
65535.
Source/Destination Protocol Tables for the AI198 Menu System
The following tables are organized according to source protocols. Match the
destination protocol with the source protocol to find the appropriate menu item
entries:
z
z
z
z
z
z
z
z
8-12
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Source/Destination Protocol Tables
Table 8-1 Asynchronous Source Without Breaks (AI198)
Source Destination Menu Item
Information
ASY.link_number
Async
Async
01
04
08
01
04
PVC
ASY.link_number
ASY.link_number
Async
X.25 SVC
The following options are available:
z X25.link_number.called_address
z X25.link_number.{ caller_address
| call_user_data }
ꢀ
Note: called_addressmust be a valid
X.121 address.
ASY.link_number
Async
Async
X.25 PVC
TCP
01
04
08
01
04
PVC
X25.link_number.lcn
ASY.link_number
ip_address#tcp_port_number
8-13
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Source/Destination Protocol Tables
Table 8-2 Asynchronous Source With Breaks (AI198)
Source
Destination Menu Item Information
ASY.link_number
Async,
Async
TL1,
Async
X.25 SVC
with X.29
break
01
04
The following options are available:
z X25.link_number.called_address
z X25.link_number.{caller_address
packetized
on a CR
(or .02 s
idle time)
| call_user_data }
ꢀ
Note: called_addressmust be a valid
X.121 address.
11
The following options are available:
z
Async: leave blank
z
Async TL1: TL1 (Refer to TL1 on
z
Async packetized: PKT -P13 -I2
10
01
04
08
11
ASY.link_number
Async,
Async
TL1,
Async
packetized
on a CR
(or .02 s
idle time)
X.25 PVC
with X.29
break
PVC
X25.link_number.lcn
The following options are available:
z
Async: leave blank
z
Async TL1: TL1 (Refer to TL1 on
z
Async packetized: PKT -P13 -I2
10
01
04
10
ASY.link_number
Async
TCP with
telnet break
ip_address#tcp_port_number
8-14
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Source/Destination Protocol Tables
Table 8-3 X.25 SVC Source Without Breaks (AI198)
Source
Destination Menu Item
Information
X.25 SVC X.25 SVC
01
04
Call user data or called address or
caller’s address
The following options are available:
z X25.link_number.called_address
z X25.link_number.{caller_address
| call_user_data}
ꢀ
Note: called_addressmust be a valid
X.121 address.
X.25 SVC X.25 PVC
01
Call user data or called address or
caller’s address
04
08
01
PVC
X25.link_number.lcn
X.25 SVC TCP
Call user data or called address or
caller’s address
ip_address#tcp_port_number
04
01
X.25 SVC AI193-TX
TCP with N
protocol
Call user data or called address or
caller’s address
ip_address#tcp_port_number
04
10
01
option
X.25 SVC Async
Call user data or called address or
caller’s address
04
08
PVC
ASY.link_number
8-15
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Source/Destination Protocol Tables
Table 8-4 X.25 SVC Source With Breaks (AI198)
Source
Destination Menu Item
Information
X.25 SVC,
X.25 SVC
and reply to
X.29 break
TCP with
telnet break
01
Call user data or called address or
caller’s address
ip_address#tcp_port_number
04
11
10
01
X.25 SVC
AI193-TX
TCP with N
protocol
option
Call user data or called address or
caller’s address
ip_address#tcp_port_number
04
Called
protocol
X.25 SVC,
X.25 SVC
with TL1
packetizing with async
and X.29
break
Async with
asyncbreak,
Async TL1
Alias name
Call user data or called address or
caller’s address
Called
address
PVC
break,
Async
packetized
on CR (or
.02 s idle
time)
ASY.link_number
Call data
Caller’s
protocol
The following options are available:
z
SVC: PAD
SVC with TL1: PAD TL1
z
Called
The following options are available:
protocol
z
Async: leave blank
z
Async TL1: TL1
z
Async packetized: PKT -P13 -I2
8-16
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Source/Destination Protocol Tables
Table 8-5 X.25 PVC Source Without Breaks (AI198)
Source
Destination Menu Item
Information
X25.link_number.lcn
X.25 PVC X.25 SVC
Alias name
Called
The following options are available:
address
z X25.link_number.called_address
z X25.link_number.{caller_address
| call_user_data}
ꢀ
Note: called_addressmust be a valid
X.121 address.
X25.link_number.lcn
X.25 PVC X.25 PVC
Alias name
Called
PVC
address
X25.link_number.lcn
Call data
X25.link_number.lcn
X.25 PVC TCP
X.25 PVC Async
Alias name
ip_address#tcp_port_number
Called
address
X25.link_number.lcn
Alias name
Called
PVC
address
ASY.link_number
Call data
Table 8-6 X.25 PVC Source With Breaks (AI198)
Source
Destination
Menu Item Information
X25.link_number.lcn
X.25 PVC,
X.25 PVC
and reply to
X.29 break
TCP with
telnet break
Alias name
ip_address#tcp_port_number
Called
address
Caller’s
protocol
Called
protocol
8-17
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Source/Destination Protocol Tables
Table 8-6 X.25 PVC Source With Breaks (AI198) (Continued)
Source
Destination
Menu Item Information
X25.link_number.lcn
X.25 PVC,
X.25 PVC
with TL1
packetizing
and X.29
break
Async with
async break,
Async TL1
with async
break, Async
packetizedon
a CR
Alias name
Called
address
PVC
ASY.link_number
Call data
Caller’s
protocol
The following options are available:
(or .02 s idle
time)
z
X.25 PVC: PAD
X.25 PVC TL1: PAD TL1
z
Called
The following options are available:
protocol
z
Async: leave blank
z
Async TL1: TL1
Async packetized: PKT -P13 -I2
z
Table 8-7 TCP/IP Source Without Telnet Breaks (AI198)
Source Destination Menu Item
Information
ip_address#tcp_port_number
TCP
X.25 SVC
Alias name
Called
The following options are available:
address
z X25.link_number.called_address
z X25.link_number.{ caller_address|
call_user_data}
ꢀ
Note: called_addressmust be a valid
X.121 address.
ip_address#tcp_port_number
TCP
X.25 PVC
Alias name
Called
PVC
address
X25.link_number.lcn
Call data
8-18
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Source/Destination Protocol Tables
Table 8-7 TCP/IP Source Without Telnet Breaks (AI198) (Continued)
Source Destination Menu Item
Information
ip_address#tcp_port_number
ip_address#tcp_port_number
TCP
TCP
Alias name
Called
address
ip_address#tcp_port_number
TCP
Async
Alias name
Called
PVC
address
ASY.link_number
Call data
Table 8-8 TCP/IP Source With Telnet Breaks (AI198)
Source Destination
Menu Item
Information
ip_address#tcp_port_number
TCP
X.25 SVC
with X.29
break
Alias name
Called
address
The following options are available:
z X25.link_number.called_address
z X25.link_number.{ caller_address|
call_user_data}
ꢀ
Note: called_addressmust be a valid
X.121 address.
Caller’s
protocol
Called
protocol
ip_address#tcp_port_number
TCP
X.25 PVC
with X.29
break
Alias name
Called
address
PVC
X25.link_number.lcn
Call data
Caller’s
protocol
Called
protocol
8-19
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Source/Destination Protocol Tables
Table 8-8 TCP/IP Source With Telnet Breaks (AI198) (Continued)
Source Destination
Menu Item
Information
ip_address#tcp_port_number
TCP
Async with
Alias name
async break
Called
PVC
address
ASY.link_number
Call data
Caller’s
protocol
Source/Destination Protocol Tables for the AI296 Menu System
The following tables are organized according to source protocols. Match the
destination protocol with the source protocol to find the appropriate menu item
entries:
z
z
z
z
z
z
z
z
Table 8-9 Asynchronous Source Without Breaks (AI296)
Source Destination Menu Item
Information
ASY.link_number
PVC
Async
Async
Alias name
Called
address
ASY.link_number
Call data
8-20
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Source/Destination Protocol Tables
Table 8-9 Asynchronous Source Without Breaks (AI296) (Continued)
Source Destination Menu Item
Information
ASY.link_number
Async
X.25 SVC
Alias name
Called
The following options are available:
address
z X25.link_number.called_address
z X25.link_number.{ caller_address
| call_user_data }
ꢀ
Note: called_addressmust be a valid
X.121 address.
ASY.link_number
Async
Async
X.25 PVC
Alias name
Called
address
PVC
X25.link_number.lcn
ASY.link_number
Call data
TCP
Alias name
ip_address#tcp_port_number
Called
address
8-21
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Source/Destination Protocol Tables
Table 8-10 Asynchronous Source With Breaks (AI296)
Source
Destination Menu Item Information
ASY.link_number
Async,
Async
TL1,
X.25 SVC
with X.29
break
Alias name
Called
address
The following options are available:
z X25.link_number.called_address
Async
z X25.link_number.{caller_address
packetized
on a CR
(or.02 s
idle time)
| call_user_data }
ꢀ
Note: called_addressmust be a valid
X.121 address.
Caller’s
protocol
The following options are available:
z
Async: leave blank
z
Async TL1: TL1 (Refer to TL1 on
z
Async packetized: PKT -P13 -I2
Called
protocol
ASY.link_number
Async,
Async
TL1,
Async
X.25 PVC
with X.29
break
Alias name
Called
address
PVC
packetized
on a CR
(or .02 s
idle time)
X25.link_number.lcn
Call data
Caller’s
protocol
The following options are available:
z
Async: leave blank
z
Async TL1: TL1 (Refer to TL1 on
z
Async packetized: PKT -P13 -I2
Called
protocol
ASY.link_number
Async
TCP with
Alias name
telnet break
ip_address#tcp_port_number
Called
address
Called
protocol
8-22
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Source/Destination Protocol Tables
Table 8-11 X.25 SVC Source Without Breaks (AI296)
Source
Destination Menu Item
Information
X.25 SVC X.25 SVC
Alias name
Call user data or called address or
caller’s address
Called
The following options are available:
address
z X25.link_number.called_address
z X25.link_number.{caller_address
| call_user_data}
ꢀ
Note: called_addressmust be a valid
X.121 address.
X.25 SVC X.25 PVC
Alias name
Call user data or called address or
caller’s address
Called
PVC
address
X25.link_number.lcn
Call data
X.25 SVC TCP
Alias name
Call user data or called address or
caller’s address
ip_address#tcp_port_number
Called
address
X.25 SVC AI193-TX
TCP with N
protocol
Alias name
Call user data or called address or
caller’s address
ip_address#tcp_port_number
Called
address
option
Called
protocol
X.25 SVC Async
Alias name
Call user data or called address or
caller’s address
Called
PVC
address
ASY.link_number
Call data
8-23
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Source/Destination Protocol Tables
Table 8-12 X.25 SVC Source With Breaks (AI296)
Source
Destination Menu Item
Information
X.25 SVC,
X.25 SVC
and reply to
X.29 break
TCP with
telnet break
Alias name
Call user data or called address or
caller’s address
ip_address#tcp_port_number
Called
address
Caller’s
protocol
Called
protocol
X.25 SVC
AI193-TX
TCP with N
protocol
option
Alias name
Call user data or called address or
caller’s address
ip_address#tcp_port_number
Called
address
Called
protocol
X.25 SVC,
X.25 SVC
with TL1
packetizing with async
and X.29
break
Async with
asyncbreak,
Async TL1
Alias name
Call user data or called address or
caller’s address
Called
address
PVC
break,
Async
packetized
on CR (or
.02 s idle
time)
ASY.link_number
Call data
Caller’s
protocol
The following options are available:
z
SVC: PAD
SVC with TL1: PAD TL1
z
Called
The following options are available:
protocol
z
Async: leave blank
z
Async TL1: TL1
z
Async packetized: PKT -P13 -I2
8-24
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Source/Destination Protocol Tables
Table 8-13 X.25 PVC Source Without Breaks (AI296)
Source
Destination Menu Item
Information
X25.link_number.lcn
X.25 PVC X.25 SVC
Alias name
Called
The following options are available:
address
z X25.link_number.called_address
z X25.link_number.{caller_address
| call_user_data}
ꢀ
Note: called_addressmust be a valid
X.121 address.
X25.link_number.lcn
X.25 PVC X.25 PVC
Alias name
Called
PVC
address
X25.link_number.lcn
Call data
X25.link_number.lcn
X.25 PVC TCP
X.25 PVC Async
Alias name
ip_address#tcp_port_number
Called
address
X25.link_number.lcn
Alias name
Called
PVC
address
ASY.link_number
Call data
Table 8-14 X.25 PVC Source With Breaks (AI296)
Source
Destination
Menu Item Information
X25.link_number.lcn
X.25 PVC,
X.25 PVC
and reply to
X.29 break
TCP with
telnet break
Alias name
ip_address#tcp_port_number
Called
address
Caller’s
protocol
Called
protocol
8-25
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Source/Destination Protocol Tables
Table 8-14 X.25 PVC Source With Breaks (AI296) (Continued)
Source
Destination
Menu Item Information
X25.link_number.lcn
X.25 PVC,
X.25 PVC
with TL1
packetizing
and X.29
break
Async with
async break,
Async TL1
with async
break, Async
packetizedon
a CR
Alias name
Called
address
PVC
ASY.link_number
Call data
Caller’s
protocol
The following options are available:
(or .02 s idle
time)
z
X.25 PVC: PAD
X.25 PVC TL1: PAD TL1
z
Called
The following options are available:
protocol
z
Async: leave blank
z
Async TL1: TL1
Async packetized: PKT -P13 -I2
z
Table 8-15 TCP/IP Source Without Telnet Breaks (AI296)
Source Destination Menu Item
Information
ip_address#tcp_port_number
TCP
X.25 SVC
Alias name
Called
The following options are available:
address
z X25.link_number.called_address
z X25.link_number.{ caller_address|
call_user_data}
ꢀ
Note: called_addressmust be a valid
X.121 address.
ip_address#tcp_port_number
TCP
X.25 PVC
Alias name
Called
PVC
address
X25.link_number.lcn
Call data
8-26
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Source/Destination Protocol Tables
Table 8-15 TCP/IP Source Without Telnet Breaks (AI296) (Continued)
Source Destination Menu Item
Information
ip_address#tcp_port_number
ip_address#tcp_port_number
TCP
TCP
Alias name
Called
address
ip_address#tcp_port_number
TCP
Async
Alias name
Called
PVC
address
ASY.link_number
Call data
Table 8-16 TCP/IP Source With Telnet Breaks (AI296)
Source Destination
Menu Item
Information
ip_address#tcp_port_number
TCP
X.25 SVC
with X.29
break
Alias name
Called
address
The following options are available:
z X25.link_number.called_address
z X25.link_number.{ caller_address|
call_user_data}
ꢀ
Note: called_addressmust be a valid
X.121 address.
Caller’s
protocol
Called
protocol
ip_address#tcp_port_number
TCP
X.25 PVC
with X.29
break
Alias name
Called
address
PVC
X25.link_number.lcn
Call data
Caller’s
protocol
Called
protocol
8-27
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Source/Destination Protocol Tables
Table 8-16 TCP/IP Source With Telnet Breaks (AI296) (Continued)
Source Destination
Menu Item
Information
ip_address#tcp_port_number
TCP
Async with
Alias name
async break
Called
PVC
address
ASY.link_number
Call data
Caller’s
protocol
8-28
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Protocol Processing Modules
Protocol Processing Modules
Protocol processing modules are used to process data as it passes though AI296.
The following topics are covered in this section:
z
z
Module Types
The following module types are available:
z
z
z
z
z
z
z
z
z
z
z
z
AEP
The Applied Innovation encapsulation protocol works with messages traveling
between X.25 and TCP/IP protocols. AEP allows for packet preservation of X.25 data
when transport is over a TCP/IP network. This protocol keeps packet boundaries
intact, which is useful for X.25 applications that are highly sensitive to packet integrity.
AEPN
The Applied Innovation encapsulation protocol with the network option is used for
messages traveling between X.25 and TCP/IP protocols. In addition to the services
provided by the AEP protocol, the AEPN also passes X.25 Q-bit information over a
TCP/IP connection. AEPN also handles special information such as break signals.
8-29
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Protocol Processing Modules
AEPX
Applied Innovation encapsulation extension is similar to AEPN, but adds the ability to
transport X.25 interrupt/reset packets and interrupt/reset confirmation packets
through TCP.
ASY
This module takes a single argument that specifies the string to be transmitted on the
outgoing connection when a call is placed. The string typically contains a modem dial
sequence.
Optional Parameters
Echo
Causes local echo from an ASY port.
Edit
Buffers calls for line editing and sends lines as a whole when ENTER is
pressed. Lines can be edited by using BACKSPACE .
BX25NM
The BX.25 network module is used to translate to and from the AEPN module and the
Configuration on page 6-5 for information about configuring BX.25 parameters.
BX25S
The BX.25 session layer module provides the session layer to X.25 that is required for
the AMATPS protocol. Typically, this module is used with the BX25NM module. Refer
parameters.
ETER
End to end reset is used on a PVC in the data transfer state to pass reset requests
without confirmation. The endpoint is responsible for confirming the reset which is
also passed through. This option works only with PVCs and is used on the X.25 side
of the connection.
PAD
Packet assembler disassembler works with messages traveling between X.25 and
asynchronous protocols. The X.25 protocol does not use break signals, but the
asynchronous protocol does. PAD converts X.25 Q-bits into asynchronous breaks,
and vice versa.
ꢀ
Note: This protocol processing module can be put on an X.25 data stream.
8-30
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Protocol Processing Modules
Defaults
Passes breaks upstream
Passes breaks downstream
Sends no reply to breaks
Optional Parameters
-U
Prevents the PAD protocol from passing breaks upstream.
-D
Prevents the PAD protocol from passing breaks downstream.
Causes the PAD protocol to reply to X.25 breaks.
-R
-7:21
Causes the X.3 parameter to behave like X.25. This option sends an
interrupt packet (an indication of a break PAD message) and discards data
to the terminal.
-M
Enables Macstar compatibility.
Example
PAD -U
Provides PAD break handling, but prevents the break from being
propagated upstream.
XXX PAD
The packet assembler disassembler is a device that collects data from a group of
terminals and outputs the data in packets (data organized in a special format). It can
also take the data packets from a host and turn them into a character stream that can
be transmitted to the terminals. The XXX PAD is defined by the following values:
z
X.3—Specifies the parameter for terminal handling functions such as baud rate,
flow control, character echoing, and other functions for a connection to an X.25
host.
z
X.28—Specifies the user interface for locally controlling a PAD.
ꢀ
Note: The communication server is not a PAD.
z
X.29—Specifies a protocol for setting the X.3 parameters via a network
connection.
XXX PAD calls can be made from AI296 with a PAD shell command or by defining an
alias that routes a call to the destination XXX PAD call. An XXX PAD destination is
defined like an X.25 SVC destination with the addition of XXX as the called protocol.
When XXX is used as a call protocol, it can take arguments to set the X.3 parameters,
similar to the setcommand used within the padshell command.
8-31
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Protocol Processing Modules
PKT
The packetizing module holds data as it arrives until AI296 receives specified
characters (such as new lines). Once the packetizing character is received, all of the
data that has been held is passed on as a single packet. This module also allows data
to be packetized on a timer, which you can set. It also allows you to specify which
characters, if any, to be filtered out of the data stream. PKT works on all protocols.
Defaults
Sets no packetizing timer
Sets no idle packetizing timer
Sets no filter characters
Passes the break upstream
Passes the break downstream
Discards unpacketized data when passing the break upstream
Optional Parameters
-Td
Sets the packetizing timer to d hundredths of a second. It packetizes d
hundredths of a second after the last time it was packetized. By setting d
to zero, the option is turned off.
-Id
Sets the idle packetizing timer to dhundredths of a second. It packetizes
after dhundredths of a second after not receiving any new characters.
-Pd,d,d
Sets the packetizing characters to the numbers entered in each doption.
Specify up to 16 characters.
-Fd,d,d
Sets the filter characters to the numbers entered in each doption.
Specify up to 16 characters. It is possible to packetize on a filtered
character.
-U
Prevents the passing of breaks upstream.
-D
Prevents the passing of breaks downstream.
-S
Packetizes on a specific sequence of characters. Enter up to 16
characters. The packet module accepts only one -Sparameter.
-E
Activates local echo back to the original Telnet session. It behaves like
an X.25 when X.3 parameter 3 is set to 1.
Examples
PKT -T6
Provides packetizing and sets the packetizing timer to .06
seconds.
8-32
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Protocol Processing Modules
PKT -P0xD,0x3B
PKT -F10,127
PKT -U
Provides packetizing and sets the packetizing characters to
carriage return and semi-colon.
Provides packetizing and filters out the characters for line
feed and delete.
Provides packetizing but prevents breaks from being
propagated upstream.
PKT -I10 -P0x0D -D
PKT -S13,10
RBP
Provides packetizing on carriage returns for .10 seconds of
idle time and prevents breaks from being propagated
downstream.
Provides packetizing and sets the sequence to carriage
return followed by a line feed.
Record boundary preservation is a Cisco protocol that works with messages traveling
between X.25 and TCP/IP protocols. RBP allows for packet preservation of X.25 data
when transport is over a TCP/IP network.
RBP is equivalent in functionality to AEP in that X.25 packet boundaries are
maintained with the addition of a configurable record boundary.
Optional Parameter
RBP -Md
Defines the maximum record size in bytes. RBP will split an incoming
X.25 data packet across multiple records so that no single record
exceeds this value. X.25 packets with this parameter set will be
combined as long as the resulting record does not exceed this value. If
this value is not set, each X.25 data packet will be converted into exactly
one record. Valid range for this parameter is 256 to 1500. The default is
no M-bit.
TL1
The Translation Language One module typically works with messages traveling
between X.25 and asynchronous protocols. However, it also works with all other
protocols. Some OSSs require that each TL1 command/response be fully contained
in one X.25 packet. By packetizing on the TL1 termination characters (“;<>”), the TL1
module ensures that each TL1 command/response is transmitted in one X.25 packet.
8-33
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Protocol Processing Modules
Defaults
Sets no packetizing timer
Sets no idle packetizing timer
Sets no filter characters
Passes the break upstream
Passes the break downstream
Discards unpacketized data when passing the break upstream
Optional Parameters
-Td
Sets the packetizing timer to dhundredths of a second. It packetizes d
hundredths of a second after the last time it was packetized. By setting d
to zero, this option is turned off.
-Id
Sets the idle packetizing timer to dhundredths of a second. It packetizes
after dhundredths of a second after not receiving any new characters.
-Pd,d,d
Sets the packetizing characters to the numbers entered in each doption.
Specify up to 16 characters.
-Fd,d,d
Sets the filter characters to the numbers entered in each doption.
Specify up to 16 characters. It is possible to packetize on a filtered
character.
-U
Prevents the passing of breaks upstream.
-D
Prevents the passing of breaks downstream.
-S
Packetizes on a specific sequence of characters. Enter up to 16
characters. The packet module accepts only one -Sparameter.
-E
Activates local echo back to the original Telnet session. It behaves like
an X.25 when X.3 parameter 3 is set to 1.
8-34
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Protocol Processing Modules
Examples
TL1 -T6
Provides TL1 packetizing and sets the packetizing timer to .06
seconds.
TL1 -F10,127
TL1 -U
Provides TL1 packetizing and filters out the characters for line
feed and delete.
Provides TL1 packetizing and prevents breaks from passing
upstream.
TL1 -120 -D
Provides TL1 packetizing on TL1 delimiters for 20 seconds of idle
time. Prevents breaks from passing downstream.
TN
The Telnet module filters Telnet commands out of the data stream and processes
them appropriately. It also adds commands, as necessary, to data as it travels
downstream. When a Telnet break is received, it is converted to an X.25 or
asynchronous break as required. When an X.25 or asynchronous break is received
from upstream, it is converted to a Telnet break and passed downstream.
Defaults
Passes breaks upstream
Passes breaks downstream
Initiates Telnet negotiation for WILL Echo and WILL SGA
Optional Parameters
-U
Prevents passing break upstream.
-D
Prevents passing break downstream.
-Ed,d
Initiates Telnet negotiation for WILL Echo and WILL Suppress Go Ahead
(SGA). This is useful when a Telnet connection is made to a remote device
that provides an echo. If d,dis specified, then the Telnet negotiation string
is modified. The Telnet negotiation string can be up to 32 characters.
8-35
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Protocol Processing Modules
Examples
TN -U
Provides Telnet handling, but prevents breaks from being
propagated upstream.
TN -E
Provides Telnet handling and initiates Telnet negotiation for WILL
Echo and WILL SGA.
TN -E255,1
Provides Telnet handling and causes the Telnet session to send IAC
(255) ECHO (1) when the connection is initiated. Initiates WILL SGA.
Module Properties
buffers all received data until a specified character is received in that data. The TN
module looks for Telnet commands embedded in the data.
between the following protocols:
z
z
z
z
z
z
z
z
X.25 (with X.29 break) to asynchronous break
X.25 (with X.29 break) to Telnet break
Asynchronous break to X.25 (with X.29 break)
Asynchronous break to Telnet break
Telnet break to X.25 (with X.29 break)
Telnet break to asynchronous break
X.29 break propagation across TCP connections between two AI296 cards
Asynchronous break propagation across TCP connections between two AI296
cards
z
Response to an indication of X.29 break.
ꢀ
Module Arguments
Some modules use protocol arguments to place restrictions on functionality. For
example, the PKT module uses arguments to specify the characters to filter out of
data and the characters to packetize in data.
8-36
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Protocol Processing Modules
Use the following guidelines when entering arguments:
z
Enter values separated by a comma in octal (base 8), hexadecimal (base 16), or
decimal (base 10) format. Octal numbers have a leading zero and hexadecimal
z
z
z
Type characters as their ASCII value.
Do not use decimal points, tabs, or spaces when entering arguments.
Enter at least one value when a doption is included with an argument. d
represents the ASCII value for a character. Valid values are from 0 to 255.
Table 8-17 displays descriptions for protocol argument entries.
Table 8-17 Protocol Argument Entries
Entry Description
0x0d
59
Specifies a carriage return in hexadecimal format.
Specifies a semi-colon in decimal format.
Specifies letter “a” in octal format.
0141
55
Specifies number “7” in ASCII decimal format.
8-37
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Alias Macros
Alias Macros
An alias macro is a program within an alias that translates incoming call requests into
outgoing call requests. It is a shortcut that allows a programmer to write many aliases
by only writing one macro.
Macros allow routing calls with fewer aliases. Using them with alternate routing
provides multiple routes for a single alias.
A macro may be entered for combinations of any or all of the following items: Alias
names, called addresses, caller’s addresses, call data, application-specific strings,
alternate routing aliases.
The following topics are covered in this section:
z
z
Alias Macro Components
This section discusses the components in an alias macro, including:
z
z
z
z
z
z
z
Start Symbols
The start symbol for an alias macro is an equal (=) sign. It is followed by one or more
alias macro components.
Comments
Comments are added at the programmer’s discretion to explain macro functionality.
Comments can be entered either on a blank line or at the end of a line containing a
macro. To enter a comment on a blank line, it must begin with two forward slashes (//).
To enter a comment in a field with a macro, it must begin with a pound sign (#) at the
end of a macro.
8-38
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Alias Macros
This example displays a comment on its own line in the Application String field and a
comment after a macro in the Alternate Route field.
Application String . ........................................... //links 1-4
Alternate Route . . ................................. ="6145550384"#from OH
ꢀ
Note: The pound sign (#) can be entered as part of the macro string if it is enclosed
in either single or double quotes. The pound sign may be either directly
enclosed (=A+’#’+D(C)), or the string that the pound sign resides in may be
enclosed (=‘198.127.1.4#23’).
Constants
Macro constants are either fixed alphanumeric characters enclosed in single or
double quotes or integers between positive and negative 2,147, 483, 647. All strings
equal zero. Strings cannot be used in mathematical functions.
Variables
information.
ꢀ
Note: Variables are not case-sensitive.
Table 8-18 Macro Variables
Variable
Value
C (CUD)
Specifies a “call user data” variable.
A (CALLED) Specifies a “called address” variable.
B (CALLER) Specifies a “caller’s address” variable.
Wildcard Symbols
Macros have two available wildcard symbols:
z ? matches any single character.
z * matches zero or more characters.
ꢀ
Note: Alias names that use wildcards are not really macros. Wildcards are not
processed in alias names that start with ‘=’.
8-39
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Alias Macros
Operators
Operators are used for calculation of mathematical expressions in alias macros.
AI296 evaluates expressions from left to right in order of precedence as shown in
of an expression in parentheses ( ) to calculate that portion first.
4+3*2
Specifies an equation that equals 10.
(4+3)*2 Specifies an equation that equals 14.
list of all available operators in order of precedence.
Table 8-19 Operators in Order of Precedence
Operator Description
#
Specifies a comment at the ends the alias macro expression.
*
/
Specifies a multiplication operation.
Specifies a division operation.
%
Specifies the remainder of a division operation.
+
-
Specifies an addition operation.
Specifies a subtraction operation.
Expressions that use the following operators return “0” for a false condition and “-1”
for true condition:
<<
<<=
=
Specifies a less than evaluation.
Specifies a less than or equal to evaluation.
Specifies an equal to evaluation.
>
>=
<<>
Specifies a greater than evaluation.
Specifies a greater than or equal to evaluation.
Specifies a not equal to evaluation.
&
Specifies a boolean logical AND evaluation. This requires that two
conditions are true before continuing with the evaluation.
^
Specifies a boolean logical exclusive OR evaluation. This requires that
one condition or another (not both) is true before continuing with the
evaluation.
|
Specifies a boolean logical OR evaluation. This requires that one
condition or both conditions are true before continuing with the
evaluation.
8-40
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Alias Macros
Table 8-19 Operators in Order of Precedence (Continued)
Operator Description
!
Specifies a boolean logical NOT evaluation. This changes a true
condition to a false condition (and vice versa) before continuing with
the evaluation.
Functions
Functions are preset command keywords that perform string and value conversions.
Some functions can be entered with only a single character. For example, sand
switchrepresent the same function.
ꢀ
Note: Functions are not case-sensitive.
Table 8-20 lists available functions and their descriptions in alphabetical order.
Table 8-20 Alias Macro Functions
Alias Macro Function
Description of Operation
asc(string)
Returns the ASCII integer value of the first
character in a string.
chr$(n)
Returns the character that corresponds to ASCII
integer value n.
hex$(n)
or
h(n)
Returns the hexadecimal equivalent to decimal
value n. For example, =hex$(31)returns hex value
1F.
if(expression,a,b)
or
Returns aif expressionis not zero or bif
expressionis zero.
i(expression,a,b)
left$(string,n)
or
Returns the left-most ncharacters of string. If nis
greater than the length of string, the function
returns the entire string.
l(string,n)
len(string)
or
n(string)
Returns the length of string.
mid$(string,x,n)
or
Returns ncharacters from stringstarting with the
xth character. If xis greater than the length of
string, the function returns a null string. If fewer
than ncharacters follow character x, the function
returns to end of the string.
m(string,x,n)
8-41
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Alias Macros
Table 8-20 Alias Macro Functions (Continued)
Alias Macro Function
Description of Operation
mid$(string,x)
or
Returns characters from stringstarting with the
xth character and continuing to the right-most end
character. If xis greater than the length of string,
the function returns a null string.
m(string,x)
myip(n)
Returns a string representation of the nth IP
address assigned to AI296. nmust be greater than
0.
pos(string,char,n)
or
Returns the position of the nth occurrence of char
in string. If there are less than noccurrences of
char in string, the function returns the length of
string.
p(string,char,n)
right$(string,n)
or
Returns the right-most ncharacters of string.
Returns the entire string if nis greater than the
length of the string.
r(string,n)
str$(n)
or
d(n)
Returns nconverted into a decimal string.
switch(target_exp,
If target_expmatches exp1, the function returns
default,exp1,result1,exp2 result1. If target_expmatches exp2, the function
,result2...)
returns result2. This continues through all pairs of
expressions and results. If target_expdoes not
match any of the expressions, then defaultis
returned.
or
s(target_exp,default,exp1
,result1,exp2,result2...)
val(string)
or
v(string)
Converts a string to its decimal integer value. For
example, =v(”032”)returns integer 32.
?(n)
Returns the nth wildcard string from the alias
match.
8-42
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Alias Macros
Alias Macro Configuration
Often there are several ways to write a macro and get the same result. One
programmer will likely design macros differently than another.
ꢀ
Note: From the Alias Menu, you can input a string with * in it and the search will
break apart the string using * as a delimiter. The search checks the alias list
for an alias name that contains the components. It does not limit the search to
the beginning and end of text of the alias as in AI198.
Configuration Examples
This example displays an alias where:
z
Alias name 172.16.32.237#30* matches source address 172.16.32.237 with a
port number of 30 followed by zero or more characters
z
z
The caller’s address is PVC
Call data ='ASY.'+D((V(?(1))%6)+1) creates strings from ASY.1 to ASY.6.
Alias Edit Menu
Alias Name . . . . . ..................................... 172.16.32.237#30*
Destination . . . . .......................................................
Caller's Address . . ................................................... PVC
Called Address . . . .......................................................
Call Data . . . . . .............................. ='ASY.'+D((V(?(1))%6)+1)
This example displays an alias where:
z
Alias name 43042* matches source addresses that start with 43042 and may
end with zero or more characters
z
Called Address ='ASY.'+D((V(?(1))%6)+1) creates a called address string of
ASY.1 through ASY.6.
Alias Edit Menu
Alias Name . . . . . ................................................ 43042*
Destination . . . . .......................................................
Caller's Address . . .......................................................
Called Address . . . .............................. ='ASY.'+D((V(?(1))%6)+1)
Call Data . . . . . ................................................. TOSUN
8-43
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Alias Macros
This example displays an alias where:
z
z
z
Alias name =L(A,P(A,’#’,1)-1)=MYIP(1) matches the base IP address of AI296
with any port number.
Called address =’10.9.8.7#’+R(A,LEN(A)-P(A,’#’,1)) redirects the call to
10.9.8.7 with the same port number.
Called protocol TN specifies that the Telnet protocol is used for the connection
to the called address.
Alias Edit Menu
Alias Name . . . . . ............. =L(A,P(A,’#’,1)-1)=MYIP(1)
Destination . . . . .......................................
Caller's Address . . .......................................
Called Address . . . ... =’10.9.8.7#’+R(A,LEN(A)-P(A,’#’,1))
Call Data . . . . . .......................................
Caller's Protocol ..........................................
Called Protocol . ....................................... TN
8-44
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Alias Configuration Examples
Alias Configuration Examples
Examples are given for the following connections:
z
z
z
z
SVC to SVC Connection
called address of 6145551234. The call continues on the outgoing AI296 on baseport 32,
link 4 and called address 6145553897:
Called Address
6145551234
IP Address
172.16.1.111
Called Protocol
TL1
X.25 Network
TCP/IP Network
X.25 Network
AI296 Incoming
AI296 Outgoing
Baseport 16
Link 2
Baseport 32
Link 4
Called Address
6145553897
Figure 8-2 SVC to SVC Connection Diagram
8-45
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Alias Configuration Examples
This example displays the menu items used to configure the SVC to SVC connection:
>10 TL1
Menu 8
01 Alias name -------------------------------------------------------6145551234
02+SLC Routing
03 Destination ----------------------------------------------------172.16.1.111
04 Called address ---------------------------------------------X25.4.6145553897
05 This alias is visible in the destination menu-----------------------------NO
06 Link number is (1..16) -
07 Caller's address -
08 Call data -
09 App. string -
10 Called protocol ---------------------------------------------------------TL1
11 Caller's protocol -
12 Alternate routing alias -
16+Test macros
17 Show the first entry in the alias translation table
18 Show the next entry in the alias translation table
19+Delete the above alias translation entry
20 Save the changes made
21 Exit this menu with no changes
Enter item number and optional ",value" then push <CR> key
8-46
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Alias Configuration Examples
SVC to PVC Connection
called address of 6145551234. The call continues on the outgoing AI296 on baseport 32,
link 1:
Called Address
6145551234
Called Protocol
IP Address
172.16.1.111
TL1
X.25 Network
TCP/IP Network
X.25 Network
AI296 Incoming
AI296 Outgoing
Baseport 32
Link 1
Baseport 16
Link 2
LCN 4
LCN 3
Figure 8-3 SVC to PVC Connection Diagram
8-47
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Alias Configuration Examples
This example displays the menu items used to configure an SVC to PVC connection:
>10 TL1
Menu 8
01 Alias name -------------------------------------------------------6145551234
02+SLC Routing
03 Destination ----------------------------------------------------172.16.1.111
04 Called address ----------------------------------------------------------PVC
05 This alias is visible in the destination menu-----------------------------NO
06 Link number is (1..16) -
07 Caller's address -
08 Call data -----------------------------------------------------------X25.1.4
09 App. string -
10 Called protocol ---------------------------------------------------------TL1
11 Caller's protocol -
12 Alternate routing alias -
16+Test macros
17 Show the first entry in the alias translation table
18 Show the next entry in the alias translation table
19+Delete the above alias translation entry
20 Save the changes made
21 Exit this menu with no changes
Enter item number and optional ",value" then push <CR> key
ꢀ
menu items in this example.
8-48
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Alias Configuration Examples
PVC to SVC Connection
with the alias of 16.X25.2.3. The call then continues out the outgoing AI296 on baseport
32 and called address 6145553897:
Alias 16.X25.2.3
Called Protocol
TL1
IP Address 172.16.1.111
X.25 Network
TCP/IP Network
X.25 Network
AI296 Incoming
AI296 Outgoing
Baseport 16
Link 2
Baseport 32
Link 4
Called Address 6145553897
Figure 8-4 PVC to SVC Connection Diagram
8-49
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Alias Configuration Examples
This example displays the menu items used to configure a PVC to SVC connection.
>10 TL1
Menu 8
01 Alias name -------------------------------------------------------16.X25.2.3
02+SLC Routing
03 Destination ----------------------------------------------------172.16.1.111
04 Called address ---------------------------------------------X25.4.6145553897
05 This alias is visible in the destination menu-----------------------------NO
06 Link number is (1..16) -
07 Caller's address -
08 Call data -
09 App. string -
10 Called protocol ---------------------------------------------------------TL1
11 Caller's protocol -
12 Alternate routing alias -
16+Test macros
17 Show the first entry in the alias translation table
18 Show the next entry in the alias translation table
19+Delete the above alias translation entry
20 Save the changes made
21 Exit this menu with no changes
Enter item number and optional ",value" then push <CR> key
ꢀ
menu items in this example.
8-50
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Alias Configuration Examples
MLT Route
You can use aliases to route MLT call information through a TCP/IP network. The
alias is configured for an AI296 card that is connected to the host and the other is
configured for an AI296 card that is connected to an NE.
Alias Name:
Called Address
Example: MLT:3
Called Address: Destination IP Address
Example: 192.168.1.140#1001
Called Protocol: AEPN -L
Link 3
Link 6
TCP/IP Network
NE
MLT Host
AI296
AI296
Alias Name:
ip_address#tcp_port_number
Example: 192.168.1.140#1001
Caller’s Address:MLT:link_number
Example: MLT:6
Caller’s Protocol:AEPN -L
Figure 8-5 MLT Call Routing Example
8-51
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Alias Configuration Examples
This example displays the menu items used to configure the MLT host alias shown in
10,AEPN -L
Menu 8
01 Alias name ------------------------------------------------------------MLT:3
02+Simple alias translation
03 Destination -
04 Called address -------------------------------------------192.168.1.140#1001
05 This alias is visible in the destination menu-----------------------------NO
06 Link number is (1..16) -
07 Caller's address -
08 Call data -
09 App. string -
10 Called protocol -----------------------------------------------------AEPN -L
11 Caller's protocol -
12 Alternate routing alias -
14+Test macros
15 Show entire alias
16 Show the first entry in the alias translation table
17 Show the previous entry in the alias translation table
18 Show the next entry in the alias translation table
19+Delete the above alias translation entry
20 Save the changes made (20b: to the beginning, 20e: to the end)
21 Exit this menu with no changes
Enter item number and optional ",value" then push <CR> key
>
This example displays the menu items used to configure the MLT network element
>11 AEPN -L
Menu 8
01 Alias name -----------------------------------------------192.168.1.140#1001
02+Simple alias translation
03 Destination -
04 Called address -
05 This alias is visible in the destination menu-----------------------------NO
06 Link number is (1..16) -
07 Caller's address ------------------------------------------------------MLT:6
08 Call data -
09 App. string -
10 Called protocol -
11 Caller's protocol ---------------------------------------------------AEPN -L
12 Alternate routing alias -
14+Test macros
15 Show entire alias
16 Show the first entry in the alias translation table
17 Show the previous entry in the alias translation table
18 Show the next entry in the alias translation table
19+Delete the above alias translation entry
20 Save the changes made (20b: to the beginning, 20e: to the end)
21 Exit this menu with no changes
Enter item number and optional ",value" then push <CR> key
>
8-52
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Alias Configuration Examples
Link-to-Link Call Routing
Link-to-link call routing lets users route all SVC calls coming in on one X.25 link to
another X.25 link. By using X.25 link-to-link call routing, it is now possible to create a
default route for all calls from a specified X.25 link. The alias for the default link-to-link
route can route all calls destined for the same link. On previous versions of AI296,
users had to create an alias for each unique called address.
network. Aliases route calls from NE1 and NE2 to the network elements. A link-to-link
call route exists between links 1 and 2, and between links 3 and 4. An incoming X.25
SVC call from NE1 that does not match an alias in the table would be routed to link 2,
and an incoming X.25 SVC call from NE2 that does not match an alias in the table
would be routed to to link 4.
Important: The link-to-link call alias must be at the end of the alias list. If the
link-to-link alias is above an actual destination alias, an X.25 SVC call
will be processed by the default link-to-link alias.
Link 1
Link 2
NE 1
Link-to-Link Calls
X.25 Packet
Network
Link 4
Link 3
AI296
NE 2
IP Network
NE 3
NE 4
AI296
Figure 8-6 Link-to-Link Routing Example
8-53
AI296 Version 9.8x User’s Guide
Alias and Call Routing Configuration: Alias Configuration Examples
This example displays AI296 configured to listen for all SVC calls on links 1 and 3 and
Alias Edit Menu
Alias Name . . . . . ............................................. X25.1.SVC
Destination . . . . .......................................................
Caller's Address . . .......................................................
Called Address . . . ............................................... X25LL.2
Call Data . . . . . .......................................................
Caller's Protocol . .......................................................
Called Protocol . . .......................................................
Application String . .......................................................
Alternate Route . . .......................................................
Description . . . . .......................................................
Display Alias in Destination Menu . . . . . . . . . . . . . .
Alias Location . . . . . . . . . . . . . . . . . . .
[Yes]
No
[End]
Beginning
+ Alias Test Menu
<F1> Help <F2> Send
<F4> Close
<Ctrl-R> Return to Main Menu
Alias Edit Menu
Alias Name . . . . . ............................................. X25.3.SVC
Destination . . . . .......................................................
Caller's Address . . .......................................................
Called Address . . . ............................................... X25LL.4
Call Data . . . . . .......................................................
Caller's Protocol . .......................................................
Called Protocol . . .......................................................
Application String . .......................................................
Alternate Route . . .......................................................
Description . . . . .......................................................
Display Alias in Destination Menu . . . . . . . . . . . . . .
Alias Location . . . . . . . . . . . . . . . . . . .
[Yes]
Beginning
No
[End]
+ Alias Test Menu
<F1> Help <F2> Send
<F4> Close
<Ctrl-R> Return to Main Menu
8-54
AI296 Version 9.8x User’s Guide
AI296 Commands: Commands Overview
Commands Overview
AI296 is configurable directly through the local system using shell commands or
through AI198 using winslc commands and the menu system.
Shell Commands
Shell commands offer some of the same functionality available in the AI296 local
menu system, including:
z
z
z
z
z
z
z
Creating, modifying, or deleting users and passwords
Accessing the AI296 menu
Configuring PVCs
Monitoring performance and diagnostic information
Pinging an IP address
Setting up an ARP table
Setting the trace level.
Shell Connections
Before using the shell commands, a shell connection to AI296 must be established.
You can connect locally using an asynchronous port on the AI296 front panel or
remotely using a Telnet connection.
Establishing a Local Shell Connection
Establish a local shell connection to AI296 through any port configured as a login port.
(By default, all ports are configured as login ports, but only port 1 is enabled.)
1. Use a PC or laptop with terminal emulation software such as HyperTerminal to
connect to AI296. For information on operating your particular terminal emulation
software, refer to the documentation provided with the program.
2. Set up your terminal emulation software to connect using COM port 1 (COM1).
3. Configure COM port 1 with the following parameters:
z
z
z
z
z
Bits per second: 9600
Data bits: 8
Parity: None
Stop bits: 1
Flow control: None
4. From within your terminal emulation software, press ENTER to request a login
prompt.
9-2
AI296 Version 9.8x User’s Guide
AI296 Commands: Commands Overview
5. At the login prompt, enter your user name.
6. At the password prompt, enter your password.
ꢀ
Notes: aiis the default user name and password. AI296 allows only five logins
using the default password. On the sixth login, AI296 will prompt you to
change the default password to a new password.
ꢀ Keep a copy of your username and password in a safe place. If you lose
or forget your password on AI296 in standalone mode, you must call
Kentrox customer service for assistance in gaining access to the card.
The destination menu appears.
7. Enter ai.
Establishing a Remote Shell Connection
Establish a remote shell connection to AI296 using AI198 command telnetor using
another Telnet client. To establish a Telnet session:
1. Use a PC or laptop with terminal emulation software such as HyperTerminal to
connect to AI296. For information on operating your particular terminal emulation
software, refer to the documentation provided with the program.
2. For user name, enter ai.
3. For password, enter ai. The destination menu appears.
4. For destination, enter ai. The [296] prompt appears.
9-3
AI296 Version 9.8x User’s Guide
AI296 Commands: winslc Commands
winslc Commands
The winslc commands let the user communicate with AI296 from AI198. Use these
commands to enter data, diagnose problems, and retrieve information from AI296.
Displaying winslc Command Logging
To monitor winslc commands, press CTRL+l when logged into AI198 to turn on
logging.
Using winslc Commands
To use winslc commands, the user must be logged into AI198 to receive output from
AI296. AI198 relays the command to AI296, which processes the command and
sends the result to the system log port (as configured in AI198 Menu 1.1). Valid winslc
commands are:
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
From the AI198, you can view the available winslc commands by entering the
following command:
winslc baseport help
where baseportspecifies the baseport number of AI296.
Log/Alarm Message Header
To obtain output from winslc commands, enable the activity/alarm log (AI198 Menu
1.1, menu item 01*The activity and alarm log is turned). The first line of the response
for most winslc commands shows the following standard log/alarm message header:
>@AI19807:42:26 081104 Sev=F Base=016 Msg:
9-4
AI296 Version 9.8x User’s Guide
AI296 Commands: winslc Commands
Table 9-1 describes the Log/Alarm message header elements.
Table 9-1 Log/Alarm Message Header Elements
Header Element Description
@AI198
Specifies the node name for the device that is producing the
log/alarm message (in this case, AI198).
7:42:26
081104
Sev=F
Specifies the current time.
Specifies the current date.
Specifies the message severity level.
Specifies the line card baseport number.
Introduces the log/alarm message.
Base=016
Msg
9-5
AI296 Version 9.8x User’s Guide
AI296 Commands: aaa
aaa
Description
These commands configure TACACS+ accounting, authentication, and authorization
settings.
Command Type
shell
Formats
aaa
account { disable | enable }
authen { disable | enable } [ all | async | telnet | ftp ]
author { priv-lvl | command }
chpass
fallback { disable | enable }
ppp authen { link_range | * } { disable | enable | fallback }
profile { priv_range } { profile_name | default }
retry { retry_count | default }
stat [ clear ]
summary
timeout { timeout_value | default }
Parameters
account
Enables or disables TACACS+ accounting of user login events and
shell command events. An accounting start packet or stop packet is
issued each time a user logs into or out of AI296. An accounting start
packet is also issued for each shell command that is run.
ꢀ
Note: If enabled, accounting is performed for all shell connection
types (Async, Telnet, and FTP), even if authentication is
disabled. For information about authentication, refer to
command aaa authen.
The following parameters are accepted:
z disable—Disables TACACS+ accounting.
z enable—Enables TACACS+ accounting.
9-6
AI296 Version 9.8x User’s Guide
AI296 Commands: aaa
authen
Enables or disables TACACS+ authentication for AI296 command shell
access. TACACS+ authentication may be enabled on all connections,
or on a connection type basis. By default, TACACS+ authentication is
disabled on all connection types. The following parameters are
accepted:
z all—Enables or disables TACACS+ authentication on all
connection types.
ꢀ
Note: If no connection type is specified, all is automatically
selected.
z async—Enables or disables TACACS+ authentication on
asynchronous link connections.
z disable—Disables TACACS+ authentication.
z enable—Enables TACACS+ authentication.
z ftp—Enables or disables TACACS+ authentication on FTP
connections.
z telnet—Enables or disables TACACS+ authentication on Telnet
connections.
author
Configures the TACACS+ authorization method for the AI296 shell.
The authorization method can be either privilege level or
per-command. Privilege level authorization is based on the priv-lvl
returned from the TACACS+ server. Per-command authorization
requires AI296 to contact the TACACS+ server for each shell command
run by a user. Individual commands are then allowed or denied.
ꢀ
Note: Authorization is performed only on the connection types that
have enabled authentication. For information about enabling
authentication, refer to command aaa authen.
The following parameters are accepted:
z command—Configures the TACACS+ authorization method that
requires to contact the TACACS+ server for each shell command
run by a user. Individual commands are then allowed or denied.
z priv-lvl—Configures the TACACS+ authorization method based
on the priv-lvl returned from the TACACS+ server.
chpass
Changes the current user’s password on the TACACS+ server.
ꢀ
Note: The TACACS+ server may not support, or be configured to
support, password changes.
9-7
AI296 Version 9.8x User’s Guide
AI296 Commands: aaa
fallback
Enables or disables TACACS+ fallback for shell access. If TACACS+
fallback is enabled and attempts to contact all configured TACACS+
servers fail, then AI296’s user database is used for authentication and
authorization. The AI296 local log file is used for accounting. The
following parameters are accepted:
z disable—Disables TACACS+ fallback.
z enable—Enables TACACS+ fallback.
ppp
authen
Enables or disables TACACS+ authentication and sets the fallback
mode for specified AsyncPPP links.
ꢀ
Note: The link type must be set to AsyncPPP for this command to
have any effect.
The following parameters are accepted:
z *—Specifies all links.
z disable—Disables TACACS+ authentication.
z enable—Enables TACACS+ authentication.
z fallback—Enables TACACS+ authentication with fallback.
z link_range—Defines a link or range of links. Valid values are 1 to
16. Individual values are separated by commas (,) and hyphens (-).
For example, 1,4-6 specifies links 1, 4, 5, and 6.
9-8
AI296 Version 9.8x User’s Guide
AI296 Commands: aaa
profile
Associates a custom profile with a privilege level or range of privilege
levels. The following rules apply:
z
TACACS+ privilege levels range from 0 to 15.
z
Custom profiles can be associated with privilege levels 2 through
14.
z
z
Privilege levels 2 through 14 default to the management system
profile.
Privilege levels 0, 1, and 15 are reserved for the Status,
Management, and Supervisor system profiles (respectively).
ꢀ
Note: For information on creating custom profiles, refer to command
Privilege levels are used only if the authorization method is set to
priv-lvl. The only exception to this occurs under all of the following
conditions:
1. The authentication server returns a privilege level.
2. The authorization server cannot be reached.
3. The authorization is set to per-command and fallback is enabled.
ꢀ
Note: For information on configuring the authorization method, refer
to command aaa author.
The following parameters are accepted:
z default—Removes the association between a range of privilege
levels and a profile.
z priv_range—Defines the range of privilege levels that will be
associated with the profile. Individual values are separated by
commas (,) and hyphens (-). For example, 1,4-6 specifies privilege
levels 1, 4, 5, and 6.
z profile_name—Specifies the name of an existing profile.
retry
Configures the number of consecutive connection attempts that are
made to a TACACS+ server before the attempt fails. Consecutive
attempts are only made if the TACACS+ server responds but refuses a
connection. If no response is received from a TACACS+ server before
the configured timeout period, then no further connection attempts are
made. For information on configuring the timeout period, refer to
The following parameters are accepted:
z retry_count—Defines the number of consecutive connection
attempts that are made. Valid values are 1 to 100.
z default—Resets the number of connection attempts to the default
value.
9-9
AI296 Version 9.8x User’s Guide
AI296 Commands: aaa
stat
Displays or clears AAA specific counters and statistics. The following
parameter is accepted:
clear—Clears all counters and statistics.
summary
timeout
Displays a summary of all authentication, authorization, and accounting
settings.
Configures the number of seconds to wait for a response from a
TACACS+ server. If no response is received from the server in the
allowed number of seconds, the connection attempt fails. The following
parameters are accepted:
z timeout_value—Defines how long (in seconds) AI296 will wait for
a response from a TACACS+ server when a connection attempt is
made. Valid values are 1 to 120.
z default—Resets the timeout value to its default.
Command Defaults
Disabled TACACS+ accounting, authenitcation, and authorization
Examples
The following AAA settings are configured:
z
z
z
Enabled TACACS+ fallback
Enabled AAA accounting
Enabled AAA authentication on telnet connections
z priv-lvl authorization
z
z
Custom profile newProf with TACACS+ privilege levels 3 to 5
Enabled TACACS+ authentication for AsyncPPP links 1 to 9
z 10 retry attempts
z 15 second timeout.
[296] aaa fallback enable
[296] aaa account enable
[296] aaa authen enable telnet
WARNING: Potential lock-out:
At least one TACACS+ server must be enabled for Authentication
AND at least one TACACS+ server must be enabled for Authorization.
[296] aaa author priv-lvl
[296] aaa profile 3-5 newProf
[296] aaa ppp authen 1-9 enable
[296] aaa retry 10
[296] aaa timeout 15
[296]
9-10
AI296 Version 9.8x User’s Guide
AI296 Commands: aaa
This example displays a summary of all authentication, authorization, and accounting
settings.
[296] aaa summary
Async Shell Access:
Telnet Shell Access:
FTP Access:
Local
AAA
Local
Authorization:
Accounting:
Fallback:
Priv-lvl
Enabled
Enabled
15 seconds
10
AAA Timeout:
AAA Retry Count:
Priv-lvl 3: newProf
Priv-lvl 4: newProf
Priv-lvl 5: newProf
[296]
This example displays all AAA specific counters and statistics.
[296] aaa stats
AAA Statistics
--------------
Authentication Attempts: 0
Authentication Failures: 0
Authentication Fallbacks: 0
Authorization Attempts: 0
Authorization Failures: 0
Authorization Fallbacks: 0
Accounting Attempts: 16
Accounting Failures: 0
Accounting Fallbacks: 16
[296]
This example displays a successful password change on a TACACS+ server.
[296] aaa chpass
Old Password:
New Password:
Re-enter New password:
Password Changed
Password Change was successful
[296]
9-11
AI296 Version 9.8x User’s Guide
AI296 Commands: alarm
alarm
Description
This command:
z
z
Displays a list of the alarm groups and the overall alarm severity
Displays alarms for a specified alarm group or for a specified range of severity
levels within an alarm group
z
z
z
z
z
Displays alarms by severity level or for a specified range of severity levels
Clears all non-self-clearing alarm groups and the overall alarm severity
Clears a specified non-self-clearing alarm group
Masks a specified alarm group
Unmasks a specified alarm group.
Command Type
shell
Formats
alarm
group [ range ]
-sev [ range ]
-clear [ group ]
-mask group
-unmask group
Parameters
group
Defines the group of alarms to display, clear, mask, or unmask. Valid
values are existing alarm groups. The following parameters is accepted:
range—Defines a range of alarm severity levels to display. Valid
values are 1 to 32. Individual values in the range are separated by
hyphens (-).
-sev
Displays all alarms or a range of alarms based severity level. The
following parameters is accepted:
range—Defines a range of alarm severity levels to display. Valid
values are 1 to 32. Individual values in the range are separated by
hyphens (-).
9-12
AI296 Version 9.8x User’s Guide
AI296 Commands: alarm
-clear
Clears all non-self-clearing alarm groups or a specified non-self-clearing
alarm group.
ꢀ
Note: Only non-self-clearing alarm groups can be manually cleared.
Self-clearing alarms clear themselves when the problem that
caused the alarm is resolved.
The following parameter is accepted:
group—Defines the group of alarms to display, clear, mask, or
unmask. Valid values are existing alarm groups.
-mask
Prevents a specified alarm group from affecting overall alarm severity.
The following parameter is accepted:
group—Defines the group of alarms to display, clear, mask, or
unmask. Valid values are existing alarm groups.
-unmask
Allows a specified alarm group to affect overall alarm severity. The
following parameter is accepted:
group—Defines the group of alarms to display, clear, mask, or
unmask. Valid values are existing alarm groups.
Examples
This example displays a list of the alarm groups and the overall alarm severity.
[296]alarm
Alarm Group Sev Date & Time Message (most recent, most severe in group)
----------- --- ----------- ----------------------------------------------
*general
links
0 00-00 00:00
0 06-01 00:00 Link 1 up.
----------- --- ----------- ----------------------------------------------
*not self-clearing () masked
Overall alarm severity: 0
[296]
9-13
AI296 Version 9.8x User’s Guide
AI296 Commands: alarm
This example displays all system alarms in group links.
[296]alarm links
Num Sev Date & Time Message
--- --- ----------- ----------------------------------------------
1 0 06-01 00:00 Link 1 up.
2 0 06-01 00:00 Link 2 down.
3 0 06-01 00:00 Link 3 down.
4 0 06-01 00:00 Link 4 down.
5 0 06-01 00:00 Link 5 down.
6 0 06-01 00:00 Link 6 down.
7 0 06-01 00:00 Link 7 down.
8 0 06-01 00:00 Link 8 down.
9 0 06-01 00:00 Link 9 down.
10 0 06-01 00:00 Link 10 down.
11 0 06-01 00:00 Link 11 down.
12 0 06-01 00:00 Link 12 down.
13 0 06-01 00:00 Link 13 down.
14 0 06-01 00:00 Link 14 down.
15 0 06-01 00:00 Link 15 down.
16 0 06-01 00:00 Link 16 down.
--- --- ----------- ----------------------------------------------
'links' alarm group severity: 0
[296]
This example displays alarms for links 5-8 in group links.
[296]alarm links 5-8
Num Sev Date & Time Message
--- --- ----------- ----------------------------------------------
5 0 06-01 00:00 Link 5 down.
6 0 06-01 00:00 Link 6 down.
7 0 06-01 00:00 Link 7 down.
8 0 06-01 00:00 Link 8 down.
--- --- ----------- ----------------------------------------------
'links' alarm group severity: 0
[296]
This example displays all alarms by severity level.
[296]alarm -sev
Alarm Group Num Sev Date & Time Message
----------- --- --- ----------- ----------------------------------------------
links
links
links
links
general
1 4 06-13 14:40 Link 1 is enabled but has not come up.
5 4 06-13 14:40 Link 5 is enabled but has not come up.
10 4 06-13 14:40 Link 10 is enabled but has not come up.
12 4 06-13 14:40 Link 12 is enabled but has not come up.
1 6 06-13 14:40 Unable to find auto ID name of 222 board
----------- --- --- ----------- ----------------------------------------------
( ) masked
[296]
9-14
AI296 Version 9.8x User’s Guide
AI296 Commands: alarm
This example displays all alarms that have a severity level between 4 and 7.
[296]alarm -sev 4-7
Alarm Group Num Sev Date & Time Message
----------- --- --- ----------- ----------------------------------------------
links
links
links
links
general
1 4 06-13 14:40 Link 1 is enabled but has not come up.
5 4 06-13 14:40 Link 5 is enabled but has not come up.
10 4 06-13 14:40 Link 10 is enabled but has not come up.
12 4 06-13 14:40 Link 12 is enabled but has not come up.
1 6 06-13 14:40 Unable to find auto ID name of 222 board
----------- --- --- ----------- ----------------------------------------------
( ) masked
[296]
This example displays the clearing of all non-self-clearing alarm groups.
[296]alarm -clear
Alarm groups cleared.
Overall alarm severity set to 0.
[296]
This example displays the clearing of non-self-clearing alarm group general.
[296]alarm -clear general
Alarm group cleared.
[296]
This example displays the prevention of alarm group links from affecting the overall
alarm severity.
[296]alarm -mask links
Alarm group masked.
[296]
This example displays the unmasking of alarm group links.
[296]alarm -unmask links
Alarm group unmasked.
[296]
9-15
AI296 Version 9.8x User’s Guide
AI296 Commands: arp
arp
Description
This command displays, deletes, or adds entries in the ARP cache.
Command Types
shell and winslc
Formats
For the shell:
arp
-a [ ip_address ]
-d ip_address
-s ip_address mac_address
For the winslc command:
winslc baseport arp
-a [ ip_address ]
-d ip_address
-s ip_address mac_address
Parameters
-a
Displays all entries in the ARP cache table or just the ip_addressentry.
The following parameter is accepted:
ip_address—Defines the IP address of the destination device in
dotted decimal format.
baseport
Defines the baseport number for AI296.
-d
Deletes an entry from the ARP cache table. The following parameter is
accepted:
ip_address—Defines the IP address of the destination device in
dotted decimal format.
-s
Adds a permanent entry to the ARP cache for the current session.
Permanent entries must be in the same subnetwork as the IP address
of the destination device. The following parameters are accepted:
z ip_address—Defines the IP address of the destination device in
dotted decimal format.
z mac_address—Defines the MAC address of the destination device.
9-16
AI296 Version 9.8x User’s Guide
AI296 Commands: arp
Examples
This example displays all ARP cache entries.
[296] arp -a
Internet Address
172.16.52.16
172.16.2.9
[296]
Ethernet Address
00-00-92-90-F2-D9
00-40-72-00-7F-96
Type
temp
temp
Life
5 mins
2 mins
Column
Description
Internet Address
Ethernet Address
Type
Displays the IP address of the destination device.
Displays the MAC address of the destination device.
Displays the type of ARP cache entry as perm or temp. Type temp
specifies that the entry is temporary and will be deleted when the
time interval specified in the Life column expires. Type perm
specifies that the entry was entered by the user with the -s
option. This entry will not expire and can be removed using the
-ddelete option.
ꢀ
Note: Resetting AI296 clears both permanent and temporary
entries.
Life
Displays the time interval for which the temporary entry will
remain in the ARP cache.
This example displays an ARP cache entry with IP address 10.40.5.20.
[296]arp -a 10.40.5.20
Internet Address
10.40.5.20
[296]
Ethernet Address
00-01-02-EE-A8-30
Type
temp
Life
4 mins
This example displays the configuration of an ARP cache entry with IP address
10.40.53.2 and MAC address 08-00-09-4a-c5-5a.
[296]arp -s 10.40.53.2 08-00-09-4a-c5-5a
10.40.53.2 mapped to Ethernet address 08-00-09-4A-C5-5A
[296]
9-17
AI296 Version 9.8x User’s Guide
AI296 Commands: arp
This example displays the deletion of an ARP cache entry with IP address 10.40.53.2.
[296]arp -d 10.40.53.2
Mapping for 10.40.53.2 deleted
[296]
9-18
AI296 Version 9.8x User’s Guide
AI296 Commands: break
break
Description
This command terminates an asynchronous or shell connection. Use command diag-
connections and connection ID numbers.
ꢀ
Note: This command only works for calls connected to the shell.
CAUTION: This command operates without regard to current activity on the serial
port.
Command Types
shell and winslc
Formats
For the shell command:
break { link_number | connection_origin }
break -id id_number
For the winslc command:
winslc baseport break { link_number | connection_origin }
winslc baseport break -id id_number
Parameters
connection_origin
Defines the IP address and port number of the device
connection being terminated.
baseport
Defines the baseport number for AI296.
id_number
Defines the ID number of the device connection being
terminated.
link_number
Defines the link number for the connection being terminated.
9-19
AI296 Version 9.8x User’s Guide
AI296 Commands: break
Examples
This example displays the termination of a shell connection for a device with IP
address 10.40.5.11 and port number 1821.
[296]break 10.40.5.11#1821
Breaking connection: 10.40.5.11#1821
[296]
This example displays the termination of a connection for a device with ID 65.
[296]break -id 65
Breaking connection with ID: 65
[296]
9-20
AI296 Version 9.8x User’s Guide
AI296 Commands: bridge
bridge
Description
This command dumps a list of all the addresses in the bridge table or clears the
bridge table.
Command Types
shell
Formats
bridge { dump | clear }
Parameters
dump
Dumps a list of all the addresses in the bridge table.
clear
Clears the bridge table.
Examples
This example displays the dumping of the bridge table.
[296]bridge dump
Hash table for Bridge Group 0:
MAC Address
Source Interface
Ethernet
Ethernet
Link 16
00:00:92:90:CF:42
00:00:92:90:CD:42
00:40:72:00:D2:43
00:60:47:CC:DB:43
00:00:92:90:CF:44
00:A0:C9:25:9A:B1
00:40:72:00:73:B8
00:40:72:00:41:C7
00:00:92:90:95:C8
00:00:92:90:C7:CE
00:10:4B:64:25:CF
00:00:92:90:0C:D0
00:00:92:9B:58:D3
00:00:92:B6:3A:D5
00:00:0E:3A:02:D5
00:10:83:F5:A5:D8
00:00:92:90:96:DB
00:00:92:90:95:DF
00:40:72:00:AF:E7
Ethernet
Ethernet
Ethernet
Ethernet
Ethernet
Ethernet
Ethernet
Ethernet
Ethernet
Ethernet
Ethernet
Ethernet
Ethernet
Ethernet
Ethernet
Link 16
9-21
AI296 Version 9.8x User’s Guide
AI296 Commands: creset
creset
Description
This command resets the error counters for a link or a range of links. There is no
output for this command. To see if the error counters were reset for the links you
Command Types
shell and winslc
Formats
For the shell command:
creset range
For the winslc command:
winslc baseport creset range
Parameters
range
Defines the link or a range of links being reset. Valid values are:
z
z
z
z
A single link number (for example, 3to reset error counters for link
3)
A series of link numbers separated by commas (for example, 1,2,3
to reset error counters for links 1, 2, and 3)
A range of link numbers separated by a dash (for example, 1-2to
reset error counters for links 1 and 2)
Any combination of a single link number, series, and/or range (for
example, 1,2-3to reset error counters for links 1, 2, and 3)
z * to reset error counters for all links.
baseport
Defines the baseport number for AI296.
Examples
This example displays the resetting of error counters for links 5 to 7.
[296]creset 5-7
[296]
9-22
AI296 Version 9.8x User’s Guide
AI296 Commands: date
date
Description
This command sets and displays the date and the time for AI296 when it is operating
in standalone mode.
Command Types
shell
Formats
date
Examples
This example displays the configuration of date 08-04-2005and time 10:24:49for AI296
in standalone mode.
[296]date
Today is Thursday 05-01-2004 01:09:52
Please enter the date and/or time.
Use 'MM-DD-YYYY' and/or 'hh:mm:ss' (24-hour format): 08-04-2004 10:24:49
[296]
9-23
AI296 Version 9.8x User’s Guide
AI296 Commands: debug
debug
Description
This command enables or disables the logging of debugging data.
Tip: You have to have logging turned on to view debug information from a shell
connection.
Command Type
shell
Formats
debug { alias | x25 | pvcfsm | asypvcfsm | nlipvcfsm | tpifsm |
modmuxfsm | allfsm | pppfsm | linkChange | bootp | all } { on | off }
Parameters
alias
Enables or disables the logging of alias translation debugging data.
x25
Used primarily by Kentrox Technical Support to isolate system faults.
pvcfsm
Used primarily by Kentrox Technical Support to isolate system faults.
asypvcfsm
Used primarily by Kentrox Technical Support to isolate system faults.
nlipvcfsm
Used primarily by Kentrox Technical Support to isolate system faults.
tpifsm
Used primarily by Kentrox Technical Support to isolate system faults.
modmuxfsm
Used primarily by Kentrox Technical Support to isolate system faults.
allfsm
Used primarily by Kentrox Technical Support to isolate system faults.
pppfsm
Used primarily by Kentrox Technical Support to isolate system faults.
bootp
Enables or disables the logging of bootp attempts so that users can
determine if the bootp process is still underway or if it has been
completed.
linkChange
Enables or disables the logging of debugging data when the PPP
protocol on a link has gone down.
all
Enables or disables the logging of all debugging data.
on
Enables the logging of specified debugging data.
off
Disables the logging of specified debugging data.
9-24
AI296 Version 9.8x User’s Guide
AI296 Commands: debug
Examples
This example displays the enabling of all debug data logging.
[296]debug all on
debug alias is on
debug x25 is on
debug pvcfsm is on
debug asypvcfsm is on
debug nlipvcfsm is on
debug tpifsm is on
debug modmuxfsm is on
debug allfsm is on
debug pppfsm is on
debug linkChange is on
debug mltfsm is on
debug bootp is on
[296]
9-25
AI296 Version 9.8x User’s Guide
AI296 Commands: delete
delete
Description
This command deletes a specified file that resides on AI296.
Command Type
shell
Formats
delete filename
Parameters
filename
Defines the name of the file to delete.
Examples
This example displays the deletion of file log.txt.
[296]delete log.txt
Are you sure you want to delete 'log.txt'? (y/n) y
log.txt deleted.
[296]
9-26
AI296 Version 9.8x User’s Guide
AI296 Commands: diag-conn
diag-conn
Description
This command displays a list of enabled links along with connection information for
each link. Data can be displayed continuously, one page at a time, or sent to the
screen one time only for all connections. The default mode is a continuous display.
Command Type
shell
Formats
diag-conn
Examples
This example displays existing connections across AI296.
C O N N E C T I O N S Mode: Continuous [Search Inactive]
103. ASY.1.1
113. TCP 172.16.2.9#1032
[ Idle
<--Data Transfer-->
]
SHELL
Enter S-kip, I-nternal, A-ll, M-ore, D-etail, F-ind, P-revPg, N-extPg or Q-uit:
ꢀ
Note: For explanations of the states shown, such as idle and data transfer, refer to
Display Item Description
S-kip
This option bypasses connections. It gives a prompt for the number
of connections to skip.
I-nternal
This option toggles between I-nternal and H-ide Int. I-nternal
displays all the internal loopback connections along with other
connections.
A-ll
This option displays all connections without page breaks. The
display does not show duplicate connections. For example, if
connection number 15 is connected to 30, the connection from 30
to 15 will not appear.
M-ore
This option toggles between M-oreand L-ess. It displays the link and
PVC number for X.25 PVCs, the link and X.121 addresses for X.25
SVCs, and the alias used to make the connection.
9-27
AI296 Version 9.8x User’s Guide
AI296 Commands: diag-conn
Display Item Description
D-etail
This option prompts for the ID of the connection to view and
displays details for that connection.
F-ind
This option displays specific types of connections. F-ind indicates
text matches that are applied to the display lines. The matching is
not case-sensitive. The logic for the matches can be AND or OR.
PATTERN 1, LOGIC 2, and PATTERN 3 are evaluated before
LOGIC 4 and PATTERN 5 are considered.
P-revPg
This option displays the previous page of connections. Twenty
connections per page appear. The numbers that appear in front of
the description (for example, 103. and 113.) are relative numbers
and do not represent any particular link, port, or PVC. The display
does not show duplicate connections. For example, if connection
number 15 is connected to 30, the connection from 30 to 15 will not
appear.
N-extPg
This option displays the next page of connections. Twenty
connections per page appear. The numbers that appear in front of
the description (for example, 103. and 113.) are relative numbers
and do not represent any particular link, port, or PVC. The display
does not show duplicate connections. For example, if connection
15 is connected to 30, the connection from 30 to 15 will not appear.
Q-uit
This option exits the command display and returns the user to the
prompt.
9-28
AI296 Version 9.8x User’s Guide
AI296 Commands: diag-eth
diag-eth
Description
This command monitors and displays Ethernet diagnostic information.
Using Interpretation Mode
There are three levels of diagnostic information:
z
z
z
Minimum—Displays minimal diagnostic information (mostly the packet’s source
and destination). This is the default interpretation mode setting.
Medium—Displays protocol fields that are likely to change for each packet, as
well as those with values that are out of the ordinary.
Maximum—Displays all protocol fields.
To configure interpretation mode:
1. At the prompt, enter diag-eth.
2. Enter interpret minimum, interpret medium, interpret maximum, or
interpret.
Tip: Entering interpretwith no additional parameter toggles interpretation off
and on. When interpretation is toggled from off to on, the diagnostic level is
set to the minimum level (the default).
Using the Timestamp Option
Timestamps can be configured to appear on the diagnostic display. The timestamp
value displays the calendar date and time.
To enable or disable timestamp display:
1. At the prompt, enter diag-eth.
2. Enter timestampto toggle between enabling and disabling the display of the
timestamp.
Using Promiscuous Mode
Promiscuous mode can be enabled or disabled during Ethernet diagnostic sessions.
By disabling promiscuous mode, only packets traveling on the network that are
destined for your Ethernet card appear. By enabling promiscuous mode, all the
packets traveling on the network appear.
To enable and disable promiscuous mode:
1. At the prompt, enter diag-eth.
2. Enter promiscuousto toggle between enabling and disabling promiscuous mode.
9-29
AI296 Version 9.8x User’s Guide
AI296 Commands: diag-eth
ꢀ
Note: Operating AI296 in the promiscuous mode can reduce performance. The
default setting is disabled promiscuous mode. AI296 automatically returns
to the default setting (promiscuous mode disabled) when the user quits
the diag-ethcommand.
Using the Help Option
To obtain command help:
1. At the prompt, enter diag-eth.
2. Enter help. The diag-ethhelp screen appears.
Configuring Filters
While using the diag-ethcommand, various filters can be defined to display specific
or general diagnostic information.
Tip: There is help associated with the filtercommand. To view this help, enter
filterafter you enter diag-eth. The filterhelp screen appears.
Important: If you are connecting to AI296 using Telnet, remember to filter out the
traffic associated with the telnet connection. Failure to do so can cause
the diagnostic program to become overloaded, which makes AI296
unresponsive.
To configure a filter:
1. At the prompt, enter diag-eth.
filter formats.
Capturing Data
While using the diag-ethcommand, data can be captured for Ethernet diagnostics.
All variables and filters can be configured for specific or general information capture.
To configure data capture:
1. Define the following settings:
z
z
z
z
z
Interpretation Mode
Timestamp Mode
Promiscuous Mode
Data Mode
Filters
9-30
AI296 Version 9.8x User’s Guide
AI296 Commands: diag-eth
2. Enter go. The system starts capturing data with the user-defined settings and
filters.
3. Enter stopto stop capturing data.
Exiting the diag-eth Session
To exit the diag-ethsession, type quit. The [296] prompt appears.
Command Type
shell
Formats
diag-eth
The following formats apply to filters:
filter { add | delete } [ src mac_address ] [ dst mac_address ]
filter { add | delete } [ src ip_address ] [ dst ip_address ]
filter { add | delete } [ src ip_address#port_number ]
[ dst ip_address#port_number ]
filter { add | delete } [ src *#port_number ] [ dst *#port_number ]
filter { add | delete } protocol [ ip | tcp | udp | icmp | arp | osi ]
filter { add | delete } all
filter list
Parameters
add
Adds a filter.
delete
Deletes a filter.
src
Defines the source address (MAC, IP, or TCP/UDP)
for the filter being created.
mac_address
Defines the MAC address to use for either the source
or destination of the filter being created.
dst
Defines the destination address (MAC, IP, or
TCP/UDP) for the filter being created.
ip_address
Defines the IP address to use for either the source or
destination of the filter being created.
ip_address#port_number
Defines the IP address and the TCP/UDP port number
for either the source or destination of the filter being
created.
9-31
AI296 Version 9.8x User’s Guide
AI296 Commands: diag-eth
*#port_number
protocol
Defines the TCP/UDP port number regardless of the
MAC/IP address settings.
Adds or deletes a specific protocol filter. Available
protocol filters are:
z
z
z
z
z
z
ip
tcp
udp
icmp
arp
osi.
all
Deletes all the filters or adds a filter to show all
Ethernet traffic.
list
Lists all the filters in the system.
Examples
This example displays the configuration of diagnostic interpretation level mediumfor the
Ethernet diagnostic session display.
[296]diag-eth
interpret medium
Interpretation is now set to MEDIUM.
This example displays the enabling and disabling of the timestamp display.
[296]diag-eth
timestamp
Timestamps will now be displayed.
timestamp
Timestamps will no longer be displayed.
This example displays the enabling and disabling of promiscuous mode.
[296]diag-eth
promiscuous
The ethernet chip is now in promiscuous mode.
promiscuous
The ethernet chip is now in normal mode.
9-32
AI296 Version 9.8x User’s Guide
AI296 Commands: diag-eth
This example displays Ethernet diagnostic help information.
[296]diag-eth
help
Commands for diag-eth:
interpret
quit
help
Turn on data interpretation.
Exit diag-eth.
Display this help text.
Toggle uninterpreted data display.
Toggle data timestamping.
Begin data capturing.
Terminate data capturing.
Add a data filter.
data
timestamp
go
stop
filter
promiscuous Toggle promiscuous mode for the ethernet chip.
This example displays the help associated with the Ethernet diagnostic filter
command.
[296]diag-eth
filter
Usage: FILTER <ADD|DELETE> [SRC <mac>] [DST <mac>]
FILTER <ADD|DELETE> [SRC <ipAddr>] [DST <ipAddr>]
FILTER <ADD|DELETE> [SRC <ipAddr#port>] [DST <ipAddr#port>]
FILTER <ADD|DELETE> [SRC <*#port>] [DST <*#port>]
FILTER <ADD|DELETE> PROTOCOL <IP|TCP|UDP|ICMP|ARP|OSI>
FILTER <ADD|DELETE> ALL
FILTER LIST
Where:
<mac>
is the MAC address desired, with the format
XX:XX:XX:XX:XX:XX, with each 'X' representing
a hexidecimal digit.
<ipAddr>
<port>
is the desired IP address, with the format
X.X.X.X, where 0 < X < 256.
is the desired TCP port.
9-33
AI296 Version 9.8x User’s Guide
AI296 Commands: diag-eth
This example displays the diagnostic Ethernet display when the following parameters
are entered:
z interpret max to set maximum interpretation
z timestamp to enable timestamping
z promiscuous to enable promiscuous mode
z filter add src 172.16.2.9 to add a filter for address 172.16.2.9
z data to display data
z go to start the data capture
z stop to stop capturing data.
[296]diag-eth
interpret max
Interpretation is now set to MAXIMUM.
timestamp
Timestamps will now be displayed.
promiscuous
The ethernet chip is now in promiscuous mode.
filter add src 172.16.2.9
New filter added.
data
Uninterpreted data will now be displayed.
go
----------------------------------------------------------------------
Timestamp: 11-10-2006 02:33:54.74
<- Ethernet: [ 00:40:72:00:7F:96 ] -> [ 00:00:0C:7E:F2:72 ]
Protocol [ 0x0800:IP ]
IP:
[ 172.16.2.9 ] -> [ 172.16.0.1 ]
Version [ 4 ]
Header Length [ 20 bytes ]
Type-Of-Service [ none ]
Identifier [ 37903 ]
Fragmentation Flags [ none ] Offset [ 0 bytes ]
Time-To-Live [ 60 hops ]
Protocol [ 0x01:ICMP ]
ICMP:
Type [ 8 ] Code [ 0 ]
(echo request)
00 00 48 44 41 42 43 44 45 46 47 48 49 4A 4B 4C
4D 4E 4F 50 51 52 53 54 55 56 57 58 59 5A 41 42
43 44 45 46 47 48 49 4A 4B 4C 4D 4E 4F 50 51 52
53 54 55 56 57 58 59 5A 41 42 43 44 45 46 47 48
49 4A 4B 4C
..HDABCDEFGHIJKL
MNOPQRSTUVWXYZAB
CDEFGHIJKLMNOPQR
STUVWXYZABCDEFGH
IJKL
----------------------------------------------------------------------
stop
9-34
AI296 Version 9.8x User’s Guide
AI296 Commands: diag-eth
This example displays the diagnostic Ethernet display when the following is entered:
z filter add src 00:40:72:00:d2:d9to configure a filter with source MAC address
00:40:72:00:d2:d9
z filter add dst 00:40:72:00:d2:d9 to configure a filter with destination MAC
address 00:40:72:00:d2:d9
z go to start the capture
z stop to end the capture.
[296]diag-eth
filter add src 00:40:72:00:d2:d9
New filter added.
filter add dst 00:40:72:00:d2:d9
New filter added.
go
----------------------------------------------------------------------
<- 01 80 C2 00 00 00 00 40 72 00 D2 D9 00 26 42 42
03 00 00 00 00 81 00 20 00 40 72 00 D2 D9 00 00
00 00 00 20 00 40 72 00 D2 D9 80 65 00 00 07 00
09 00 0F 00 00 00 00 00 00 00 00 00
.......@r....&BB
....... .@r.....
... [email protected]....
............
----------------------------------------------------------------------
<- 00 40 72 00 D2 D9 00 40 72 00 7F 96 08 00 45 00
00 29 0F 81 00 00 3C 06 F4 8A AC 10 02 09 AC 10
20 9A 04 16 00 17 75 87 E4 2F 30 E0 B6 B4 50 10
08 00 A6 96 00 00 41 0D 01 B4 6D 74 01 B4 FF FC
.)....<.........
.....u../0...P.
......A...mt....
----------------------------------------------------------------------
<- stop
This example displays the diagnostic Ethernet display when the following is entered:
z filter add protocol tcp to configure a filter with a defined TCP protocol
z go to start the capture
z stop to end the capture.
[296]diag-eth
filter add protocol tcp
New filter added.
go
----------------------------------------------------------------------
<- 00 A0 C9 22 D8 C4 00 00 92 B6 2F 97 08 00 45 2C
00 6C CF B7 40 00 80 06 69 4B AC 10 37 14 AC 10
32 28 10 9A 00 8B 01 67 55 24 00 D0 5D 81 50 18
1E 59 5C 61 00 00 00 00 00 40 FF 53 4D 42 2B 00
00 00 00 18 03 80 00 00 00 00 00 00 00 00 00 00
00 00 07 08 FE CA 02 10 41 0F 01 01 00 1B 00 4C
57 4F 20 43 57 20 56 4C 4F 20 44 45 4F 20 4D 41
57 20 4C 4D 57 20 41 52 57 00
..."....../...E,
2(.....gU$..].P.
.Y\[email protected]+.
................
........A......L
WO CW VLO DEO MA
W LMW ARW.
----------------------------------------------------------------------
stop
9-35
AI296 Version 9.8x User’s Guide
AI296 Commands: diag-eth
This example displays the diagnostic Ethernet display when filter list is entered to
display all filters.
[296]diag-eth
filter list
Filters currently being used by diag-eth:
protocol tcp
dst 00:40:72:00:d2:d9
src 00:40:72:00:d2:d9
dst 172.16.2.9
src 172.16.2.9
protocol tcp
This example displays the deletion of filter protocol tcp.
[296]diag-eth
filter delete protocol tcp
Filter 'protocol tcp' has been deleted.
This example displays the deletion of all filters.
[296]diag-eth
filter delete all
Filter 'dst 00:40:72:00:d2:d9' has been deleted.
Filter 'src 00:40:72:00:d2:d9' has been deleted.
Filter 'dst 172.16.2.9' has been deleted.
Filter 'src 172.16.2.9' has been deleted.
9-36
AI296 Version 9.8x User’s Guide
AI296 Commands: diag-info
diag-info
Description
This command displays diagnostic information for WAN, asynchronous, Ethernet, and
TCP connections as well as for memory. Different screens of information can be
viewed depending on the command option that is entered. The screens display the
state of serial links and system updates once per second. The available display
options are W, M, A, E, and T. They display the following information:
z
z
z
z
z
Option W displays WAN diagnostic information. W is the default display.
Option M displays the STREAMS allocation and memory information.
Option A displays asynchronous information.
Option E displays Ethernet information.
Option T displays TCP data.
ꢀ
Note: Type Xto exit the command display.
Command Type
shell
Formats
diag-info
9-37
AI296 Version 9.8x User’s Guide
AI296 Commands: diag-info
Examples
This example displays the WAN Diag Info screen, which is accessed by typing W.
W A N
D I A G
I N F O
LINK
1
STATE TX_PEND RX_WANT NO_BUF
BYTE_IN
BYTE_OUT
759050
30
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
2
3
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
4
5
6
7
8
9
10
11
12
13
14
15
16
Enter W-an, M-emory, A-sync, E-thernet, T-cp or Q-uit:
Column Description
LINK
Displays the link number.
STATE
Displays the state of the WAN driver. Two states are available:
z
0 means the X.25 frame level is not established.
30 means the X.25 frame level is established.
z
TX_PEND
RX_WANT
NO_BUF
Displays the state of the transaction if one is pending for transmission.
Displays the state of the buffer if another buffer is needed.
Displays the number of times the receiver cannot be started because no
buffers were available.
BYTE_IN
Displays the count of the number of bytes coming in.
Displays the count of the number of bytes going out.
BYTE_OUT
This example displays diagnostic information for STREAMS allocation and memory,
which are accessed by typing M.
9-38
AI296 Version 9.8x User’s Guide
AI296 Commands: diag-info
S T R E A M S
A L L O C A T I O N
NAME
Queues
Streams
FREE
8361
2085
64
ALLOC
239
115
0
%FREE
97
94
USED
1073
532
FAIL
HWM
241
116
0
0
0
0
0
0
Bufcalls
Timeouts
Message blocks
Data blocks:
Class 0
100
99
97
0
2387
16015
13
369
402908
588495
45
551
1519
4080
14944
9981
500
17
16
56
19
0
98
99
7954
835
0
0
0
0
0
0
0
0
40
18
64
32
0
Class 1
Class 2
99
99
100
60
301866
11034
0
Class 3
Class 4
Class 5
Class 6
Extended
390
260
1
0
222746
1
263
1
0
1
350
50
100
0
S Y S T E M
A L L O C A T I O N
(alloc failed=0)
USED USED_HWM UNIT_SIZE
REGION:
AI1
AI2
ASIZ CNT CNT_HWM
741664
741664
741664
324
0
424
0
17632
0
20704
0
180832
32
32
32
AI3
32
36 179296
Enter M-emory, A-sync, E-thernet, T-cp or Q-uit:
Column Description
NAME
Displays the name of the STREAMS resource.
FREE
Displays the number of free or available STREAMS resources.
ALLOC
Displays the number of STREAMS resources allocated at the time of
the display.
%FREE
USED
Displays the percent of free or available STREAMS resources.
Displays the number of STREAMS resources used since the card was
last rebooted.
FAIL
HWM
Displays the number of times an allocation failed.
Displays the highest number of resources ever allocated at one time.
Displays the memory allocation regions.
REGION
ASIZ
CNT
Displays the size of the memory allocation regions in bytes.
Displays the number of blocks allocated from a region (regardless of
size).
CNT_HWM
USED
Displays the highest number of blocks allocated since the card was last
rebooted.
Displays the number of bytes currently allocated from a region.
9-39
AI296 Version 9.8x User’s Guide
AI296 Commands: diag-info
Column Description
USED_HWM
Displays the highest number of bytes allocated since the card was last
rebooted.
UNIT_SIZE
Displays the size in bytes of the memory units that can be allocated.
This example displays diagnostic information for asynchronous connections, which is
accessed by typing A.
ASYNC DIAG INFO
LINK
1
STATE
BYTES_IN
BYTES_OUT
LINK
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
STATE
BYTES_IN
BYTES_OUT
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Enter M-emory, A-sync, E-thernet, T-cp or Q-uit:
Column Description
LINK
Displays the link number.
STATE
Displays the state of the driver. Two states are available:
z 0 specifies that the link is not established.
z 1 specifies that the link is enabled. The link does not have to have a
connection to be enabled.
BYTE_IN
Displays the number of bytes coming into the link.
Displays the number of bytes going out of the link.
BYTE_OUT
9-40
AI296 Version 9.8x User’s Guide
AI296 Commands: diag-info
This example displays diagnostic information for the front panel Ethernet interface,
which is accessed by typing E.
ETHERNET 0
Rx LG frame length violation: ---0
Rx NO nonoctet aligned frame: ---0
Rx SH short frame (runt): -------0
Rx CR CRC error: ----------------0
Rx OV overrun: ------------------0
Rx CL collision: ----------------0
Rx BSY buffers exhausted: -------0
Rx frames missed: ---------------0
Rx frames received: -------------0
Rx bytes received: --------------0
Tx RL retry limit exceeded: -----0
Tx RC collisions: ---------------0
Tx UN underruns: ----------------0
Tx LC late collisions:-----------0
Tx CSL carrier sense lost: ------2451095
Tx queued buffers: --------------0
Tx frames sent: -----------------2451095
Tx bytes sent: ------------------233814304
Unexpected interrupts: ----------0
Enter M-emory, A-sync, E-thernet, T-cp or Q-uit:
Display Item
Description
Rx LG frame length violation
Displays the number of frame length violations in
received packets.
Rx NO nonoctet aligned frame
Rx SH short frame (runt)
Rx CR CRC error
Displays the number of misaligned, received frames.
Displays the number of short received frames.
Displays the number of packets received that have
had CRC errors.
Rx OV overrun
Displays the number of packets not received by the
interface because of a receiver overrun.
Rx CL collision
Displays the transmit collisions on received frames.
This is the number of times the Ethernet device goes
to transmit but cannot because someone else is
already transmitting.
Rx BSY buffers exhausted
Rx frames missed
Displays the number of times all receive buffers
were used, but more were required.
Displays the number of frames that were supposed
to be received, but were missed.
9-41
AI296 Version 9.8x User’s Guide
AI296 Commands: diag-info
Display Item
Description
Rx frames received
Displays the number of frames received on the
connection.
Rx bytes received
Displays the number of bytes received on the
connection.
Tx RL retry limit exceeded
Tx RC collisions
Displays the number of times transmitted frames
exceeded the retry limit.
Displays the number of transmit collisions. This is
the number of times the Ethernet device goes to
transmit but cannot because someone else is
already transmitting.
Tx UN underruns
This displays the number of times the transmitter
has run out of data due to the system being busy.
Tx LC late collisions
Tx CSL carrier sense lost
Displays the number of late collisions on transmitted
frames.
Displays the number of times that the carrier sense
was lost.
Tx queued buffers
Tx frames sent
Displays the number of queued buffers.
Displays the number of frames that were
transmitted.
Tx bytes sent
Displays the number of bytes that were transmitted.
Unexpected interrupts
Displays the number of times that the transfer of
frames was unexpectedly interrupted.
9-42
AI296 Version 9.8x User’s Guide
AI296 Commands: diag-info
This example displays diagnostic information for the Ethernet sonic chip in use on this
card (SONIC0), which is accessed by typing E.
SONIC0
frames_received
bytes_received
frames_sent
2133706
2451073
204088549 233809600
317511
bytes_sent
collisions
38293966
0
0
0
0
0
0
0
0
0
0
116
0
0
transmit_errors
crc_errors
alignment_errors
missed_packets
rx_buffers_exhausted 0
0
0
heartbeatlost
rx_overruns
rba_exceeded
current_tda
ex_defers
0
0
0
8
0
0
0
0
0
0
2
0
0
ex_coll
tx_underruns
bad_tx_size
tx_blocked
tx_delayed
state
0
0
2451086
0
2451086
eth intr stuck: 0----------------233812081
Display Item
Description
frames_received
bytes_received
Displays the number of frames received on the connection.
Displays the number of bytes received on the connection.
ꢀ
Note: This field displays a negative number after it reaches
a count of 2,147,483,647. This is normal operation
and does not indicate an error.
frames_sent
bytes_sent
Displays the number of frames sent from the connection.
Displays the number of bytes sent from the connection.
ꢀ
Note: This field displays a negative number after it reaches
a count of 2,147,483,647. This is normal operation
and does not indicate an error.
collisions
Displays the number of transmit collisions. This is the
number of times the Ethernet device goes to transmit but
cannot because someone else is already transmitting.
transmit_errors
Displays the number of transmit errors that have occurred.
9-43
AI296 Version 9.8x User’s Guide
AI296 Commands: diag-info
Display Item
Description
crc_errors
Displays the number of packets received that have had CRC
errors.
alignment_errors
missed_packets
Displays the number of alignment errors.
Displays the number of missed packets.
rx_buffers_exhausted
Displays the number of times all receive buffers were used,
but more were required.
heartbeatlost
rx_overruns
rba_exceeded
Displays if there is an error between the Ethernet interface
and the Ethernet transceiver.
Displays the number of packets not received by the interface
because of a receiver overrun.
Displays the number of times that the maximum number of
receive buffers have been exceeded.
current_tda
ex_defers
Displays the current data area being transmitted.
Displays the number of times that the maximum limit on the
excessive deferral timer is exceeded. An excessive deferral
error is recorded when the following events occur:
z
A transmission attempt is made while another node is
transmitting.
z
The transmit period is longer than the excessive deferral
timer limit.
ex_coll
Displays the number of times an excessive collision has
been recorded. An excessive collision is recorded when a
transmit attempt occurs 16 times and a collision occurs each
time.
tx_underruns
bad_tx_size
tx_blocked
tx_delayed
Displays the number of times the transmitter has run out of
data due to the system being busy.
Displays the number of times the transmit byte count was
incorrect.
Displays a 1 if the transmitter is blocked. Otherwise, a 0 is
displayed.
Displays the number of times the transmitter has been
blocked.
9-44
AI296 Version 9.8x User’s Guide
AI296 Commands: diag-info
Display Item
Description
state
Displays the current state of the Ethernet interface. The
following values may appear:
z 0—The Ethernet interface is uninitialized.
z 1—The Ethernet interface is idle.
z 2—The Ethernet interface is active.
z 3—The Ethernet interface needs to be reset.
eth intr stuck
Displays the number of times the Ethernet interface interrupt
has stuck while servicing the interrupt.
This example displays diagnostic information for TCP data, which is accessed by
typing T.
T C P / I P
I N F O
Copied ethernet receive packet:
TCP keepalive failed:
0
0
1
0
TCP max keepalive tries:
Dropped SNMP request:
Enter M-emory, A-sync, E-thernet, T-cp or Q-uit:
Display Item
Description
Copied ethernet receive packet:
Displays the number of copied Ethernet receive
packets.
TCP keepalive failed:
Displays the number of TCP keep-alive
messages that have been sent and were
expected to be received, but were not received.
TCP max keepalive tries:
Dropped SNMP request:
Displays the maximum number of TCP keep-alive
messages received on the connection.
Displays the number of dropped SNMP requests.
9-45
AI296 Version 9.8x User’s Guide
AI296 Commands: diag-line
diag-line
Description
This command monitors incoming and outgoing asynchronous traffic and displays
diagnostic information for the traffic. A help screen provides a list of commands
available for line monitoring diagnostics.
CAUTION: The line monitor degrades the performance of AI296. Do not use this
command in heavy traffic situations in which performance is crucial.
ꢀ
Note: Information from the line monitor diagnostic mode only appears when data is
passed on serial links. If no data is passed, the screen is blank.
is entered.
Table 9-2 Line Monitor Mode Options
Option
data
modem
t
Function
Toggles the display of data on or off.
Toggles the display of modem signals on or off.
Toggles the display of a timestamp for each frame of data
displayed on or off.
h or r
Hides (h) or reveals (r) all lines on AI296.
Hides (h) or reveals (r) a specified line (x).
Reveals a specified LCN (y) on a specified line (x).
h lx or r lx
r lx y
r lx y z
Reveals a range of specified LCNs (y through z) on a
specified line (x).
h lx y - or r lx y -
Hides or reveals all LCNs from a specified LCN (y) on up on a
specified line (x).
h lx -y or r lx -y
Hides or reveals all LCNs from 0 to a specified LCN (y) on a
specified line (x).
filterL2
Toggles the filtering of level 2 frames without packet
information on or off.
9-46
AI296 Version 9.8x User’s Guide
AI296 Commands: diag-line
Table 9-2 Line Monitor Mode Options (Continued)
Option
Function
interpret [ a | x ]
Toggles the display of decoded packet data on the line
monitor on or off and optionally selects the format of the data
in the data portion of the packet (a or x).
z a displays the data in the data portion of the packet in
ASCII/hexadecimal format. Unprintable data
(hexadecimal values 0x00 to 0x20 and 0x7F to 0xFF)
appears as two digit hexadecimal numbers separated by
a space. Printable data appears as printable characters.
This option only applies to data.
z x displays all the data in the data portion of the packet in
hexadecimal format. All data appears as two-digit
hexadecimal numbers separated by a space. This option
only applies to data.
print
Prints the range of revealed LCNs for all lines.
Pauses the line monitor.
CTRL+s
go or CTRL+q
Reactivates the line monitor after displaying the line monitor
options.
ESC or q
Quits monitoring traffic, exits from the line monitor, and
returns to the prompt.
?
Displays a list of the options available for line monitoring
diagnostics.
Tip: Press ENTER to execute a command and press ESC to end the diagnostic
session.
CAUTION: If you are connected to AI296 through a serial port, do not monitor the
port with command diag-line. Use command hideto hide and not
monitor the port. Failure to comply with this statement can cause AI296
to become unresponsive.
Command Type
shell
Formats
diag-line
9-47
AI296 Version 9.8x User’s Guide
AI296 Commands: diag-line
Examples
This example displays a typical default line monitor display for asynchronous data.
06>d FF 03 00 31 00 01 FF FF FF FF FF FF 00 00 92 9B
59 0C 08 06 00 01 08 00 06 04 00 01 00 00 92 9B
59 0C AC 10 32 05 00 00 00 00 00 00 AC 10 22 79
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00
...1............
Y...............
Y...2........."y
................
..
06<d FF 03 02 01 00 00 00 00 00 80 00 00 40 72 00 6F
77 00 00 00 00 80 00 00 40 72 00 6F 77 80 04 00
00 14 00 02 00 0F 00
.......
06>d FF 03 00 31 00 01 FF FF FF FF FF FF 00 10 4B D0
D3 5D 08 06 00 01 08 00 06 04 00 01 00 10 4B D0
D3 5D AC 10 33 D1 00 00 00 00 00 00 AC 10 20 EB
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00
...1..........K.
.]............K.
.]..3......... .
................
..
06>d FF 03 00 31 00 01 FF FF FF FF FF FF 00 10 4B D0
D3 5D 08 06 00 01 08 00 06 04 00 01 00 10 4B D0
D3 5D AC 10 33 D1 00 00 00 00 00 00 AC 10 1E 82
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00
...1..........K.
.]............K.
.]..3...........
................
..
Column
Description
Line number
Displays the line number, which can range from 01 to 32.
Direction indicator
Displays the direction indicator for the line. One of the
following appears:
z > for transmitted frames
z < for received frames.
Frame type indicator Displays the frame type indicator for the line. One of the
following appears:
z d for asynchronous links
z
Blank for other frames or packets.
Data
If the data field byte count is disabled, it gets displayed as
ct: <# of bytes in data field>. If the data display is enabled
and only present in data packets, then the data byte count is
displayed as <ASCII STRING>.
9-48
AI296 Version 9.8x User’s Guide
AI296 Commands: diag-tconn
diag-tconn
Description
This command displays a list of enabled links along with connection information for
each link. It displays all connections on AI296 in the same format as command diag-
conn on page 9-27, but it is not interactive.
Command Types
shell and winslc
Formats
For the shell command:
diag-tconn
For the winslc command:
winslc baseport diag-tconn
Parameters
baseport
Defines the baseport number for AI296.
Examples
This example displays active connections on AI296. This is a partial display. The rest
of the response follows the pattern below for the remaining connections.
[296] diag-tconn
TIDMUXsw#1
13:26:30 040900 Sev=F Base=032 Msg:
AI232 Complete Connections Dump:
1. PARENT2
3. TCP 172.16.31.45#5001
TID(s): SONEPLEX-NE3
<-----> 32.ASY.2.1
<-----> PARENT2.1
SONEPLEX-NE4
15. TCP 192.168.31.15#5001
TID(s): NE4-DAYTON-OH
NE7-DAYTON-OH
<-----> PARENT2.2
NE5-DAYTON-OH
NE8-DAYTON-OH
NE6-DAYTON-OH
NE9-DAYTON-OH
[296]
ꢀ
Note: The connection ID is the first number that appears for each connection. For
example, the connection ID for connection PARENT2 is 1.
9-49
AI296 Version 9.8x User’s Guide
AI296 Commands: dir
dir
Description
This command displays a list of files with associated times, dates, permissions, and
sizes.
Command Type
shell
Formats
dir [ -l ]
Parameters
-l
Displays a list of the available files and file information such as permission,
time, date, and file size. The lscommand with this option is the same as the
dircommand.
Examples
This example displays all available files.
[296]dir
boot.ini
boot.img
232.img
log.txt
primary.cnf
[296]
This example displays all available files with permission, size, time, and date
information.
[296]dir -l
-rw-r--r--
-r--r--r--
-rw-r--r--
-rw-r--r--
-rw-r--r--
[296]
1 0
1 0
1 0
1 0
1 0
0
0
0
0
0
143 Jun 1 22:52 boot.ini
2175720 Aug 15 09:54 boot.img
22061 Jun 1 00:00 log.txt
4342 Aug 15 08:21 core.txt
7092 Jun 13 22:46 primary.cnf
9-50
AI296 Version 9.8x User’s Guide
AI296 Commands: exit
exit
Description
This command ends the current shell session and returns to the login prompt.
Command Type
shell
Formats
exit
Examples
This example displays an exit from the current shell session.
[296]exit
Writing Configuration ...
Goodbye.
Valid destinations are as follows:
AI
Enter destination name (or "EXIT" to logout):
>
9-51
AI296 Version 9.8x User’s Guide
AI296 Commands: head
head
Description
This command displays the first few lines of a file.
Command Type
shell
Formats
head [ -n lines ] file_name ...
Parameters
[ -nlines] Defines the number of lines to display. The default is 20.
file_name
Defines the name of the file to display.
ꢀ
Note: Several filenames can be entered with this command.
Examples
This example displays the first 30 lines of file core.txt.
[296]head -n 30 core.txt
296 crash dump at 14:16:30, 07-20-2004 (up 0 days 00:31:46):
Version 96HPC960.000007 created on 2004-03-29 at 09:43:35
Crash Code= 000000ad
PC= 00000000
SP= 00000000
IMMR= 00000000
MSR= 00000000
GPR00= 00000000
GPR03= 00000000
GPR06= 00000000
GPR09= 00000000
GPR12= 00000000
GPR15= 00000000
GPR18= 00000000
GPR21= 00000000
GPR24= 00000000
GPR27= 00000000
GPR30= 00000000
CR= 00000000
GPR01= 00000000
GPR04= 00000000
GPR07= 00000000
GPR10= 00000000
GPR13= 00000000
GPR16= 00000000
GPR19= 00000000
GPR22= 00000000
GPR25= 00000000
GPR28= 00000000
GPR31= 00000000
GPR02= 00000000
GPR05= 00000000
GPR08= 00000000
GPR11= 00000000
GPR14= 00000000
GPR17= 00000000
GPR20= 00000000
GPR23= 00000000
GPR26= 00000000
GPR29= 00000000
SSR0= 00000000
XER= 00000000
SSR1= 00000000
CTR= 00000000
LR= 00000000
PVR= 00500000
Stack dump:
PSOS1= 00000000 PSOS2= 00000000
PSOS3= 00000000
Caller
[see LR]
200082c0: 9421 ffc8 7c08 02a6 bea1 000c 9001 003c
200082d0: 7c7f 1b78 3ae0 0000 4800 1419 7c76 1b78
200082e0: 56d6 001e 3b16 3e82 a338 0000 572c 043e
200082f0: 7d96 6214 3bcc 2004 82be 0000 7ebd ab78
20008300: 7fe3 fb78 4801 76bd 7c7c 1b78 578a 043e
20008310: 2c0a 0100 4081 0008 3b80 0100 3b60 0000
20008320: 576c 043e 578b 043e 7c0c 5800 4080 001c
[296]
9-52
AI296 Version 9.8x User’s Guide
AI296 Commands: help
help
Description
This command lists all available system commands or information for a specific
command.
Command Types
shell and winslc
Formats
For the shell command:
help [ command ]
For the winslc command:
winslc baseport help [ command ]
Parameters
baseport
Defines the baseport number for AI296.
command
Defines the name of the command for which specific information will be
displayed.
Examples
This example displays a list of all available commands.
[296]help
The following commands are available:
*ftplogin
*telnetlogin
alarm
arp
break
diag-tconn
dir
more
pad
staslc
syncflash
tail
tcpoutconn
tftp
exit
head
help
id
passwd
ping
pppstatus
profile
pvcedit
pvclist
reset
bridge
creset
tftpboot
trace
type
ip
debug
delete
diag-conn
diag-eth
diag-info
diag-line
link
linkstat
log
useradd
userdel
users
sholog
show
logout
ls
menu
staeia
standalone
who
xvc
[296]
9-53
AI296 Version 9.8x User’s Guide
AI296 Commands: help
This example displays help information for command show.
[296]help show
Usage: show [perf | comments | conn | data | mem | tcp | wan | tconn |
pvc | eth | ip | router | version | log | crash | inventory |
ports]
[296]
9-54
AI296 Version 9.8x User’s Guide
AI296 Commands: ip
ip
Description
This command displays the following system settings:
z
z
z
z
z
IP address
Subnet mask
High IP address
Primary router IP address
Backup router IP address
Command Type
shell
Formats
ip
Examples
This example displays the configured IP address information.
[296]ip
IP Address
Subnet Mask High IP Address
-------------------------------------------------------
010.040.057.015
255.255.000.000
010.040.057.015
Router IP Address
-------------------------
010.040.000.001 (Default)
No backup router
[296]
9-56
AI296 Version 9.8x User’s Guide
AI296 Commands: ip init
ip init
ꢀ
Note: This command is only valid when AI296 is in standalone mode.
Description
This command configures the following settings for AI296 in standalone mode:
z
z
z
z
z
z
IP address
Subnet mask
High IP address
Primary gateway address
Backup gateway address
IP address range
CAUTION: The following message appears when the “ip init” command is invoked
and no login ports are configured:
There are no login ports currently configured for this system. Please take
necessary precautions to prevent lockout.
Command Type
shell
Formats
ip init
Examples
This example displays the prompt that appears when ip initis entered. A prompt
appears for each configurable IP address item.
[296] ip init
Enter IP Address (xxx.xxx.xxx.xxx):
9-57
AI296 Version 9.8x User’s Guide
AI296 Commands: ip init
This example displays the configuration of all the IP settings available with this
command:
[296] ip init
Enter IP Address (xxx.xxx.xxx.xxx):172.16.2.39
Setting IP Address to 172.16.2.39
Enter Subnet Mask (xxx.xxx.xxx.xxx):255.255.000.000
Setting Subnet Mask to 255.255.000.000
Enter Router Address (xxx.xxx.xxx.xxx):172.16.000.1
Setting Router Address to 172.16.000.1
Enter Backup Router Address (default none):172.16.2.41
Setting Backup Router Address to 172.16.2.41
Enter IP Address Range (default 1):
Setting range to 1
[296]
9-58
AI296 Version 9.8x User’s Guide
AI296 Commands: link
link
Description
This command is used to:
z
Force a serial link to connect or disconnect
ꢀ
Note: When this command is used to disconnect a serial link, all calls are torn
down. The serial link does not come back online until command link
startis issued.
Important: If you are connected to the AI296 shell using a serial port, remember
not to disable that port or else loss of connectivity will result.
z
z
Restart a link, which is a stop followed by a start
Show a configuration summary for a link or range of links.
Command Types
shell and winslc
Formats
For the shell command:
link { link_range | * } { restart | start | stop }
For the winslc command:
winslc baseport link { link_range | * } { start | stop | restart }
Parameters
*
Specifies all links.
baseport
Defines the baseport number for AI296.
link_range
Defines a link or range of links. Valid values are 1 to 32. Individual
values are separated by commas (,) and hyphens (-). For example,
1,4-6 specifies links 1, 4, 5, and 6.
ꢀ
Note: This parameter applies to any action the user is trying
perform (start, stop, restart, or show information).
restart
Restarts the serial links.
start
Enables the serial links.
stop
Disables the serial links.
9-59
AI296 Version 9.8x User’s Guide
AI296 Commands: link
Examples
This example displays the starting of links 1 through 4 and 6.
[296]link 1-4,6 start
[296]
This example displays the stopping of links 6 and 8.
[296]link 6,8 stop
[296]
9-60
AI296 Version 9.8x User’s Guide
AI296 Commands: linkstat
linkstat
Description
This command displays link statistic information.
Command Types
shell and winslc
Formats
For the AI296 system command:
linkstat
For the winslc command:
winslc baseport linkstat
Parameters
baseport
Indicates the baseport number of AI296.
9-61
AI296 Version 9.8x User’s Guide
AI296 Commands: linkstat
Examples
This example displays the link statistic information for AI296.
[296]linkstat
E
Link N
D R C D F P
T T T C R K Speed
Conn
Rx/Pkt
Rx/Bytes
Tx/Pkt
Tx/Bytes Rx
/CRC Rx/Abt Rx/Ovr Tx/Und Intf
R S S D M T
1: +Asy + + - -
A
9600,n,8,1 0
0 RS-232
0
0
0
0
0
0
0
0
2: +DCE + + - - - -
0
0
9600
0 RS-232
9600
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
3: +DCE + + - - - -
0
4: +DCE + + - - - -
0
0
0 RS-232
9600
0 RS-232
0
0
0
5: -DCE
0
6: +DCE + + - - - -
- - -
0
9600
0 RS-232
9600
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
7: -DCE
0
0
0
0
- - -
0 RS-232
9600
0 RS-232
9600
0 RS-232
0
0
8: -DCE
0
- - -
0
9: -DCE
0
10: -DCE
- - -
0
- - -
9600
0 RS-232
9600
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
11: -DCE
0
- - -
0
0 RS-232
9600
0 RS-232
9600
0 RS-232
0
12: -DCE
0
- - -
0
13: -DCE
0
14: -DCE
- - -
0
- - -
9600
0 RS-232
9600
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
15: -DCE
0
- - -
0
0 RS-232
9600
0 RS-232
9600
0 RS-232
0
16: -DCE
0
[296]
- - -
0
9-62
AI296 Version 9.8x User’s Guide
AI296 Commands: linkstat
This example displays link statistic information for the device at baseport 64.
AI198AISwitch Shell Connection 22
>winslc 64 linkstat
AI198AISwitch Shell Connection 22
>@AI19815:40:40 072204 Sev=F Base=064 Msg:
E
Link N
D R C D F P
T T T C R K Speed
Conn
Rx/Pkt
Rx/Bytes
Tx/Pkt
Tx/Bytes Rx
/CRC Rx/Abt Rx/Ovr Tx/Und Intf
R S S D M T
1: +Asy + + - -
A
9600,n,8,1 0
0 RS-232
0
0
0
0
0
0
0
0
2: +DCE + + - - - -
0
0
9600
0 RS-232
9600
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
3: +DCE + + - - - -
0
4: +DCE + + - - - -
0
0
0 RS-232
9600
0 RS-232
0
0
0
5: -DCE
0
- - -
0
6: +DCE + + - - - -
9600
0 RS-232
9600
0 RS-232
9600
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
7: -DCE
0
0
0
0
- - -
0
0
0 RS-232
9600
0 RS-232
8: -DCE
0
- - -
0
9: -DCE
0
10: -DCE
- - -
0
- - -
9600
0 RS-232
9600
0 RS-232
9600
0 RS-232
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
11: -DCE
0
- - -
0
@AI19815:40:41 072204 Sev=F Base=064 Msg:
- - -
0
12: -DCE
0
9600
0 RS-232
0
0
0
0
0
0
13: -DCE
0
14: -DCE
0
15: -DCE
- - -
0
- - -
0
- - -
9600
0 RS-232
9600
0 RS-232
9600
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0 RS-232
9600
0 RS-232
16: -DCE
0
- - -
0
ꢀ
Note: The example has the terminal option set to 80 columns. Setting the terminal to
132 columns is recommended.
9-63
AI296 Version 9.8x User’s Guide
AI296 Commands: log
log
Description
This command turns the display of log messages on or off.
Command Type
shell
Formats
log { on | off }
Parameters
on
Specifies the option that turns the display of log messages on.
off
Specifies the option that turns the display of log messages off.
Examples
This example displays the current status of the log message display.
[296]log
Display of log messages is currently disabled.
[296]
This example displays the activation of the log message display.
[296]log on
Display of log messages is now enabled.
[296]
This example displays the deactivation of log message display.
[296] log off
Display of log messages is now disabled.
[296]
9-64
AI296 Version 9.8x User’s Guide
AI296 Commands: ls
ls
Description
This command displays a list of available files.
Command Type
shell
Formats
ls [ -l ]
Parameters
-l
Displays a list of the available files and file information such as permission,
time, date, and size.
ꢀ
Note: Entering lswith this option is the same as entering dir.
Examples
This example displays all available files.
[296]ls
boot.ini
boot.img
log.txt
core.txt
primary.cnf
[296]
This example displays all available files with associated permission levels, times,
dates, and sizes.
[296]ls -l
-rw-r--r--
-r--r--r--
-rw-r--r--
-rw-r--r--
-rw-r--r--
[296]
1 0
1 0
1 0
1 0
1 0
0
0
0
0
0
143 Jun 1 22:52 boot.ini
2175720 Aug 15 10:05 boot.img
22061 Jun 1 00:00 log.txt
4342 Aug 15 08:21 core.txt
7092 Jun 13 22:46 primary.cnf
9-66
AI296 Version 9.8x User’s Guide
AI296 Commands: menu
menu
Description
This command accesses the AI296 main menu system.
Command Type
shell
Formats
menu
Examples
This example displays the AI296 Main Menu.
AI296 Main Menu
+ Link Menu
+ System Menu
+ IP Over X.25 Subnet Menu
+ Static Route Menu
....................................................................
:
:
: Select the desired menu option using the UP or DOWN arrow key. :
: Then press ENTER or RETURN to continue.
:..................................................................:
:
<F1> Help
<F4> Close
CAUTION: The following message appears in the shell when the user exits the main
menu and has the last login port disabled:
There are no login ports currently configured for this system. Please take
necessary precautions to prevent lockout.
This message is only seen when the system is running in standalone
mode.
9-67
AI296 Version 9.8x User’s Guide
AI296 Commands: more
more
Description
This command prints the content of a file to the current shell session one page at a
time.
ꢀ
Note: You cannot use this command to view code image files or configuration files
(.img and .cnf extensions).
Command Type
shell
Formats
more filename
Examples
This example displays the contents of file log.txt one page at a time.
[296]more log.txt
Configuration has changed
06:20:11 060600 Sev=F Msg:
User pubs from 10.40.5.20#1436 has exited the shell.
06:20:20 060600 Sev=F Msg:
User pubs from 10.40.5.20#1436 has entered the shell.
06:21:01 060600 Sev=0 Msg:
Configuration has changed
06:21:04 060600 Sev=0 Msg:
Configuration has changed
06:21:04 060600 Sev=F Msg:
User pubs from 10.40.5.20#1436 has exited the shell.
06:21:07 060600 Sev=F Msg:
User pubs from 10.40.5.20#1436 has logged out of the Destination Menu.
04:40:49 060700 Sev=F Msg:
User pubs from 10.40.5.20#2729 has logged into the Destination Menu.
04:40:51 060700 Sev=F Msg:
User pubs from 10.40.5.20#2729 has entered the shell.
Press Space for more or q to quit:
9-68
AI296 Version 9.8x User’s Guide
AI296 Commands: pad
pad
Description
This command calls an X.25 PAD host. It is used with the X.3, X.28 and X.29
protocols. Used with a link number, it calls the X.25 device connected to that link.
Without parameters, it enters the command mode.
Command Types
shell
Formats
pad
ꢀ
Note: There are several parameters available with this command. See the list below.
Parameters
break
Sends a break signal to host.
breakaction
Sets a breakaction.
breakin
Sets a PAD recall character.
call host
Sets up a connection to the named host.
clear
Closes the current connection.
echo
Enables/disables terminal echo.
emask
Sets the terminal echo mask to n.
flow
Enables/disables terminal flow control.
forward
Sets data forwarding conditions.
help
Displays help information.
hosts
Lists all the available hosts.
int
Sends an interrupt packet.
lfinsert
Sets line feed insertion action.
loghost
Displays X.29 messages.
message
Enables the message mode of operation.
native
Enables the native mode of operation.
9-69
AI296 Version 9.8x User’s Guide
AI296 Commands: pad
pagewait
Sets page wait to nlines.
param
par
Displays current X.3 parameters.
Displays specified X.3 parameters.
Defines terminal as the hardcopy device.
Sets the terminal profile.
printer
profile
quit
Exits the PAD session.
reset
rpar?
rset?
set
Resets the current call.
Displays specified remote X.3 parameters.
Sets and displays specified remote X.3 parameters.
Sets specified X.3 parameters.
set?
Sets and displays specified X.3 parameters.
Lists the status of the connection.
Enables the transparent mode of operation.
Defines the terminal as a display device.
Sets the terminal width to ncharacters.
status
transparent
vdu
width
Examples
This example displays the enabling of flow control for PAD.
[296]pad
PAD: flow
Flow = ON
PAD:
This example displays the setting of the PAD profile.
[296]pad
PAD: profile
V5
PAD:
9-70
AI296 Version 9.8x User’s Guide
AI296 Commands: passwd
passwd
Description
This command changes an existing user’s password.
Command Type
shell
Formats
passwd
ꢀ
Note: After the initial command is entered, AI296 prompts the user for
information needed to configure the new password.
Examples
This example displays the configuration of a new password for existing user pubs.
[296]passwd
Please enter the login name of the user
whose password is being changed.
pubs
Please enter the OLD password for user 'pubs'.
Please enter the NEW password.
Passwords are truncated at 10 characters.
Please retype NEW password.
Password successfully changed.
[296]
9-72
AI296 Version 9.8x User’s Guide
AI296 Commands: ping
ping
Description
This command sends an ICMP echo request to the specified IP address. If the IP
device responds to the echo request, a reply receipt message appears. If a reply is
not received within 5 seconds, a no reply message appears. This command can be
used to troubleshoot network level problems.
Command Types
shell and winslc
Formats
For the shell command:
ping ip_address
For the winslc command:
winslc baseport ping ip_address
Parameters
ip_address
Defines the IP address of the destination device in dotted decimal
format.
baseport
Defines the baseport number for AI296.
Examples
This example displays what happens when host 172.16.30.110 replies to a ping.
[296] ping 172.16.30.110
Pinging host 172.16.30.110
ICMP Echo Reply:TTL 60
Host 172.16.30.110 replied to the ping
The TTL (time-to-live) is the number of jumps or hops the message is allowed to take.
This example displays what happens when no reply is received from host
172.16.30.114.
[296] ping 172.16.30.114
Pinging host 172.16.30.114
Host 172.16.30.114 didn't reply to the ping
9-73
AI296 Version 9.8x User’s Guide
AI296 Commands: pppstatus
pppstatus
Description
This command displays the status of all ModMux and asynchronous PPP-IPCP links.
If IPCP is running on the link (the link status is RUNNING), this command also displays
the local and remote IP addresses.
Command Type
shell
Formats
pppstatus
Examples
This example displays the status of all PPP-IPCP links.
[296] pppstatus
Link Phase
1: ESTABLISH
14: SERIALCONN
[296]
Local IP Addr. Remote IP Addr.
N/A
N/A
N/A
N/A
Column
Link
Description
Displays the link number.
Phase
Displays the status of the link. Values are:
z INITIALIZE—Indicates the link is down.
z SERIALCONN—Indicates the link is up, but not connected. The
link is waiting for the data carrier detect (DCD) signal or the
data set ready (DSR) signal to come up.
z ESTABLISH—Indicates the link is up, but not connected. The
AI296 and the remote device are negotiating basic
information on how the connection will operate.
z AUTHENTICATE—Indicates the link is up, but not connected. The
link is validating ID and password information with the remote
device.
z NETWORK—Indicates the link is up, but not connected. The link
is negotiating the local and remote IP addresses.
z RUNNING—Indicates the link is up and connected. IPCP is
running on the link. The AI296 and the remote device can
transfer IP packets over the link.
9-74
AI296 Version 9.8x User’s Guide
AI296 Commands: pppstatus
Column
Description
Local IP Addr.
Displays one of the following:
The IP address of AI296 (if the link status is RUNNING)
z
z N/A (if the link status is INITIALIZE, SERIALCONN, ESTABLISH,
AUTHENTICATE, or NETWORK)
Remote IP Addr.
Displays one of the following:
z
The IP address of the remote device (if the link status is
RUNNING)
z N/A (if the link status is INITIALIZE, SERIALCONN, ESTABLISH,
AUTHENTICATE, or NETWORK)
9-75
AI296 Version 9.8x User’s Guide
AI296 Commands: profile
profile
Description
This command allows a user account profile to be customized. The following six
system profiles are maintained:
z
z
z
z
z
z
Supervisor
Management
Status
Empty
Destination menu
Connect
Profile names are limited to 19 characters. Only 20 user configurable profiles are
allowed to be configured at the same time.
Command Type
shell
Formats
profile
-n
-l profile_name
-c existing_profile new_profile
-a profile_name [ commands [ -w ] ] ...
-d profile_name [ commands ] ...
-remove [ profile_name ]
Parameters
-a
Adds commands to a profile and optionally adds write permission. The
following parameters are accepted:
z profile_name—Defines the name of a user profile.
z command—Defines the name of a command to associate with a user
profile.
z -w—Adds write permission for a command that otherwise would not
have write permission.
9-76
AI296 Version 9.8x User’s Guide
AI296 Commands: profile
-c
Creates a new profile from an existing user profile. The following
parameters are accepted:
z existing_profile—Specifies the name of an existing user profile.
z new_profile—Defines the name of a new user profile.
-d
Deletes commands from a profile. The following parameters are
accepted:
z profile_name—Defines the name of a user profile.
z command—Defines the name of a command to associate with a user
profile.
-l
Lists all commands associated with a specific user profile. The following
parameter is accepted:
profile_name—Defines the name of a user profile.
-n
Lists all user profile names.
-remove
Removes a user profile. The following parameter is accepted:
profile_name—Defines the name of a user profile.
Examples
This example displays each of the profile parameter options with associated
functionality.
[296]profile
Usage: profile -n
to list profile names
: profile -l <profile name>
to list all commands associated with a given profile
: profile -c <existing profile name> <new profile name>
to create a new profile from an existing profile
: profile -a <profile name> [commands [-w]]...
to add commands to a profile and possibly add write permission
: profile -d <profile name> [commands]...
to delete commands from a profile
: profile -remove <profile name>
to completely remove a profile
[296]
9-77
AI296 Version 9.8x User’s Guide
AI296 Commands: pvcedit
pvcedit
Description
This command allows a change to occur on a PVC without bringing down (bouncing)
the entire link. This command can also be used to reset the PVC without resetting the
entire link. If no options are specified, the PVC is simply reset. This command also
has the following constraints:
z
z
z
Only asynchronous and X.25 PVCs are to be used.
Asynchronous PVCs can be reset only.
X.25 PVCs can be reset and altered.
Command Types
shell and winslc
Formats
For the AI296 system command:
pvcedit
asy.link_number.lcn [ -a call_timer | -c inactivity_timer | -p ]
x25.link_number.lcn [ -a call_timer | -c inactivity_timer | -p ]
For the winslc command:
winslc baseport pvcedit
asy.link_number.lcn [ -a call_timer | -c inactivity_timer | -p ]
x25.link_number.lcn [ -a call_timer | -c inactivity_timer | -p ]
Parameters
-a
Forces the PVC to activate with the corresponding call
timer.
asy.link_number.lcn
Defines the link number and logical channel number for
the asynchronous PVC being edited.
baseport
Defines the baseport number for AI296.
-c
Forces the PVC to connect on activity with the
corresponding inactivity timer.
call_timer
Defines the value of the call timer. Valid values are from
30 to 600.
inactivity_timer
Defines the value for the inactivity timer. Valid values are
from 1 to 600.
9-78
AI296 Version 9.8x User’s Guide
AI296 Commands: pvcedit
-p
Forces the PVC to become passive.
x25.link_number.lcn
Defines the link number and logical channel number for
the X.25 PVC being edited.
Examples
This example displays the call timer set to 32 seconds for PVC x25.4.3.
[296]pvcedit x25.4.3 -a 32
[296]
9-79
AI296 Version 9.8x User’s Guide
AI296 Commands: pvclist
pvclist
Description
This command lists the PVCs in the system and displays their current state. If there
are many PVCs in the system, this command redirects its output to a file named
pvc.lst for easier viewing.
Command Types
shell and winslc
Formats
For the shell command:
pvclist [ link_range | * ]
For the winslc command:
winslc baseport pvclist [ link_range ]
Parameters
link_range
Defines a link or range of links. Valid values are 1 to 32. Individual
values are separated by commas (,) and hyphens (-). For example,
1,4-6 specifies links 1, 4, 5, and 6.
*
Specifies all links.
baseport
Defines the baseport number for AI296.
Examples
This example displays PVC information for link 1.
[296]pvclist 1
[PVC list]
+asy.1.1
[296]
it=0
ASD: state=idle
muxid=0
fd=65
flags=00a0
Column
First column
Description
Displays the PVC protocol type, link number, and LCN (logical
channel number).
9-80
AI296 Version 9.8x User’s Guide
AI296 Commands: pvclist
Column
Description
Second column Displays the timer type for the PVC. Possible values are:
z ct—Displays the connect timer if the PVC is active. The
number indicates the timer setting in seconds.
z it—Displays the inactivity timer if the PVC is a connect-on-
activity PVC. The number indicates the timer setting in
seconds.
z Passive—Appears if the PVC is a passive type of PVC.
Third column
Defines the state of the PVC. Possible values are:
z idle—Indicates the PVC is ready to connect.
z dataxfer—Indicates the PVC is connected and able to pass
data.
z incon—Indicates the PVC is in a transition state.
z attaching—Indicates the PVC is in a transition state.
z not attached—Indicates that the PVC is not connected.
z detached—Indicates the PVC is in a transition state.
If the display indicates one of the transition states, this should
only appear for a short period of time. If the state remains in this
condition, contact Technical Support.
Fourth column
Fifth column
Sixth column
Defines the MuxID, which is an internal number used by
developers to describe which data stream is used for the
connection.
Defines the file descriptor, which is an integer value used by
developers to describe which data stream is used for the
connection.
Defines the flag, which gives a code that indicates the purpose of
the data stream.
9-81
AI296 Version 9.8x User’s Guide
AI296 Commands: reset
reset
Description
This command resets AI296.
CAUTION: All call processing will stop and all connections will be lost during the
reboot process.
Command Type
shell
Formats
reset
Examples
This example displays the resetting of AI296.
[296] reset
Are you SURE you want to reset the system? (y/n) y
Resetting system ...
9-82
AI296 Version 9.8x User’s Guide
AI296 Commands: rz
rz
Description
This command allows AI296 to receive files from a PC using the Zmodem file transfer
protocol. This command can be executed from any asynchronous port or Telnet
connection.
ꢀ
Note: After issuing the rzcommand, if the sending PC does not begin the file
transfer within 40 seconds, the system returns to the prompt.
Command Type
shell
Formats
rz
Examples
This example displays AI296 receiving two files from a PC.
[296] rz
Ready to receive. Start your upload now.
**B01000400654a92
2 files received.
[296]
9-83
AI296 Version 9.8x User’s Guide
AI296 Commands: selcnf
selcnf
ꢀ
Note: This command is only available for AI296 in standalone mode.
Description
This command has two forms: One allows for the recovery of an overwritten runtime
configuration file and the other allows for the deletion of the specified configuration
file. Any configuration file (with a .cnf extension) can be used for system boot up. The
configuration file is written to boot.ini.
Command Type
shell
Formats
selcnf
-r
-d config_file
Parameters
-r
Specifies the option that recovers the current overwritten run-time
configuration file.
-d
Specifies the option that deletes a configuration file. The following parameter is
accepted:
config_file—Defines a configuration file for deletion; it must end with a
.cnf extension.
Examples
This example displays the available options for command selcnf.
[296]selcnf
usage: selcnf -r
selcnf [-d] <config_file>
Selects the specified config file for current configuration.
Options:
-r
-d
Recovers the current over-written run-time config file
Deletes the specified configuration file
[296]
9-84
AI296 Version 9.8x User’s Guide
AI296 Commands: sholog
sholog
Description
This command displays the contents of the log file. The last 32,000 characters of log
messages that were sent to the log port are displayed.
ꢀ
Note: This command has the same functionality as command show log.
Command Type
shell
Formats
sholog -p
Parameters
-p
Displays the content of the file one page at a time.
ꢀ
Note: This option is not available with command show log.
Examples
This example displays the contents of an AI296 log file one page at a time.
[296]sholog -p
Configuration has changed
06:20:11 060600 Sev=F Msg:
User pubs from 10.40.5.20#1436 has exited the shell.
06:20:20 060600 Sev=F Msg:
User pubs from 10.40.5.20#1436 has entered the shell.
06:21:01 060600 Sev=0 Msg:
Configuration has changed
06:21:04 060600 Sev=0 Msg:
Configuration has changed
06:21:04 060600 Sev=F Msg:
User pubs from 10.40.5.20#1436 has exited the shell.
06:21:07 060600 Sev=F Msg:
User pubs from 10.40.5.20#1436 has logged out of the Destination Menu.
04:40:49 060700 Sev=F Msg:
User pubs from 10.40.5.20#2729 has logged into the Destination Menu.
04:40:51 060700 Sev=F Msg:
User pubs from 10.40.5.20#2729 has entered the shell.
Press Space for more or q to quit:
9-85
AI296 Version 9.8x User’s Guide
AI296 Commands: show
show
Description
This command displays various types of information for AI296.
Command Types
shell and winslc
Formats
For the shell command:
show
comments
conn
crash
data [ link_range | * ]
eth
inventory
ip
log
mem
perf [ link_range | * ]
ports [ link_range | * ]
pvc
router
tconn
tcp
version
wan
For winslc, enter the following command with any of the shell command keywords:
winslc baseport show
Parameters
baseport
Defines the baseport number for AI296.
comments
Displays comments.
conn
Displays all active connections.
crash
Displays crash dump information.
9-86
AI296 Version 9.8x User’s Guide
AI296 Commands: show
data
Displays link data. The following parameters are accepted:
z link_range—Defines a link or range of links. Valid values are 1 to
32. Individual values are separated by commas (,) and hyphens (-
). For example, 1,4-6 specifies links 1, 4, 5, and 6.
z *—Specifies all links.
Displays the date and time.
Displays Ethernet information.
date
eth
inventory
Displays the serial number, product name, manufacture date, and
MAC address (when in standalone mode).
ip
Displays the IP address, subnet mask, and high IP address.
Displays the contents of the log file, same as command sholog.
Displays memory allocation.
log
mem
perf
Displays serial link performance. The following parameters are
accepted:
z link_range—Defines a link or range of links. Valid values are 1 to
32. Individual values are separated by commas (,) and hyphens (-
). For example, 1,4-6 specifies links 1, 4, 5, and 6.
z *—Specifies all links.
ports
Displays the link number, link type, and description for all available
ports or for a specified range of ports. The following parameters are
accepted:
z link_range—Defines a link or range of links. Valid values are 1 to
32. Individual values are separated by commas (,) and hyphens (-
). For example, 1,4-6 specifies links 1, 4, 5, and 6.
z *—Specifies all links.
pvc
Displays PVC connections.
router
tconn
tcp
Displays the default and backup gateway IP address.
Displays complete connections.
Displays TCP information, such as maximum keepalive tries, dropped
SNMP requests, and total opened sockets.
version
wan
Displays the version number of AI296.
Displays WAN diagnostic information.
9-87
AI296 Version 9.8x User’s Guide
AI296 Commands: show
Examples
This example displays the AI296 version number.
[296]show version
Version 96HPC961.000003 created on 2004-07-06 at 09:31:34
Boot Loader Version 96B2L103.000003
[296]
This example displays the serial link performance for links 2-5.
[296]show perf 2-5
Performance for last 60 seconds:
Intrf Type Input Chars/sec
Output Chars/sec
2
X.25
X.25
X.25
X.25
0
0
0
0
0
0
0
0
3
4
5
[296]
This example displays the link numbers, link types, and descriptions for ports 13-16.
[296]show ports 13-16
Link Type Description
13: X25
14: X25
15: X25
16: X25
[296]
9-88
AI296 Version 9.8x User’s Guide
AI296 Commands: staeia
staeia
Description
This command displays the status of the EIA leads.
Command Types
shell and winslc
Formats
For the shell command:
staeia { link_range | * }
For the winslc command:
winslc baseport staeia { link_range | * }
Parameters
link_range
Defines a link or range of links. Valid values are 1 to 32. Individual
values are separated by commas (,) and hyphens (-). For example,
1,4-6 specifies links 1, 4, 5, and 6.
*
Specifies all links.
baseport
Defines the baseport of AI296.
Examples
This example displays the status of the EIA leads for links 1 to 5.
[296]staeia 1-5
Link Type Status
IN
DCD CTS
OUT
DTR RTS
1: ASY Enabled
2: X25 Enabled
3: X25 Enabled
4: X25 Enabled
5: X25 Disabled
[296]
-
-
-
-
-
-
-
-
+
+
+
+
+
+
+
+
Column Description
DCD
DCD is an incoming EIA lead control signal. The plus symbol (+)
indicates that this lead is asserted. The minus symbol (-) indicates that
the lead is negated.
9-89
AI296 Version 9.8x User’s Guide
AI296 Commands: staeia
Column Description
CTS
DTR
RTS
CTS is an incoming EIA lead control signal. The plus symbol (+)
indicates that this lead is asserted. The minus symbol (-) indicates that
the lead is negated.
DTR is an outgoing EIA lead control signal. The plus symbol (+)
indicates that this lead is asserted. The minus symbol (-) indicates that
the lead is negated.
RTS is an outgoing EIA lead control signal. The plus symbol (+)
indicates that this lead is asserted. The minus symbol (-) indicates that
the lead is negated.
9-90
AI296 Version 9.8x User’s Guide
AI296 Commands: standalone
standalone
Description
This command enables or disables standalone mode. For more information about the
difference between standalone mode and switch mode, refer to Appendix B:
Command Type
shell
Formats
standalone { true | false }
Parameters
true
Puts AI296 in standalone mode.
false
Takes AI296 out of standalone mode.
Examples
This example displays the current standalone mode status.
[296]standalone
Currently forced standalone mode is OFF.
Currently running in switch mode.
[296]
This example displays the configuration of standalone mode for AI296.
[296]standalone true
[296]
9-91
AI296 Version 9.8x User’s Guide
AI296 Commands: staslc
staslc
Description
This command displays the status of the links and the DP232 cable.
Command Types
shell and winslc
Formats
For the shell command:
staslc { link_range | * }
For the winslc command:
winslc baseport staslc { link_range | * }
Parameters
link_range
Defines a link or range of links. Valid values are 1 to 32. Individual
values are separated by commas (,) and hyphens (-). For example,
1,4-6 specifies links 1, 4, 5, and 6.
*
Specifies all links.
baseport
Defines the baseport number for AI296.
9-92
AI296 Version 9.8x User’s Guide
AI296 Commands: staslc
Examples
This example displays the link and cable status information for links 1 to 5.
[296]staslc 1-5
Link
Current status
1: +Asy Link n,8,1
Speed Act Pmax Rx/CRC Rx/Abt Rx/Ovr Tx/Und Intf
9600
9600
9600
9600
0
0
0
0
0
0
0
0
0
0
0
0
0 RS-232
0 RS-232
0 RS-232
0 RS-232
2: +DCE -Dcd -Frm -Pkt
3: +DCE -Dcd -Frm -Pkt
4: +DCE -Dcd -Frm -Pkt
0
0
0
128
128
128
5: -DCE -Dcd -Frm -Pkt
9600
0
128
0
0
0
0 RS-232
[296]
ꢀ
Note: Not all links are displayed here. Entering the command with no additional
parameters would show all 16 links.
Column
Link
Description
Displays the number of the link.
Status
Displays the link status as dataxfer (data is being transfered),
idle, or disabled.
Appl.
Displays the application specified for the link (Alias, Login, or
Destination).
DTR RTS CTS DSR DCD
Displays the status of the control signals. (+ means the signal
is asserted and - means the signal is negated.)
Format
Displays the baud rate, number of data bits, parity (none, odd,
or even), and number of stop bits specified for the link.
Parity
Frame
Displays the number of parity errors.
Displays the number of framing errors.
Displays the number of overrun errors.
Displays the number of underrun errors.
Overun
Underun
9-93
AI296 Version 9.8x User’s Guide
AI296 Commands: syncflash
syncflash
ꢀ
Note: This command is only available when AI296 is in standalone mode.
Description
This command synchronizes the AI296 configuration with the configuration
information stored on AI198. Enabling this feature ensures that if AI296 is placed in
standalone mode, it will operate as it did in switch mode.
Command Type
shell
Formats
syncflash { true | false }
Parameters
true
Enables the update configuration functionality.
false
Disables the update configuration functionality.
ꢀ
Note: When running in standalone mode, AI296 always writes to its file system when
configuration changes are made. When running in switch mode, the running
configuration on AI296 is always kept current with AI198's configuration.
Examples
This example displays the AI296 configuration being synchronized with the
configuration information stored on AI198.
[296]syncflash true
[296]
9-94
AI296 Version 9.8x User’s Guide
AI296 Commands: sz
sz
Description
This command sends files from AI296 to a receiving PC using the Zmodem file
transfer protocol. This command can be executed from any asynchronous port or
Telnet connection.
ꢀ
Note: Before attempting to send files, AI296 sends a signal to the receiving PC. If
your emulation program does not support this feature, you may have to start
the receiving PC manually.
Command Type
shell
Formats
sz [ filename ] ...
Parameters
filename
Specifies the file to send from AI296 to the receiving PC.
Examples
This example displays file userlog.txt being sent from AI296 to the receiving PC.
[296] sz userlog.txt
Sending files.
**O
1 file sent.
[296]
9-95
AI296 Version 9.8x User’s Guide
AI296 Commands: tacacs
tacacs
Description
This command displays TACACS+ log and shell session information.
Command Type
shell
Formats
tacacs
info
sholog [ -p ]
stats [ clear ]
Parameters
info
Specifies how the current shell session was authenticated. If the
current session was authenticated by a TACACS+ server, it will display
the IP address of the server. If a TACACS+ server could not be
contacted and fallback is enabled, it will display Fallback to local. If
TACACS+ authentication was disabled, it will display Local.
sholog
Displays the contents of the TACACS+ debug log file. The TACACS+
debug log file records all connection attempts to TACACS+ servers.
The following information is displayed for each connection attempt:
z
z
z
z
A record of the timestamp
The IP address of TACACS+ server
The AAA phase
The success or failure status associated with each connection.
ꢀ
Note: The TACACS+ debug log file is only populated when TACACS+
debugging is enabled using command debug tacacs on.
The following parameters are accepted:
-p—Paginates the sholog output.
stats
Displays or clears TACACS+ specific counters and statistics. The
following parameters are accepted:
clear—Clears the counters and statistics.
9-96
AI296 Version 9.8x User’s Guide
AI296 Commands: tacacs
Examples
This example displays the TACACS+ authentication method for this shell connection
as Local.
[296] tacacs info
Current session authenticated by: Local
[296]
This example displays a TACACS+ debug log file.
[296] tacacs sholog
[02:26:32 030406] 192.168.001.074 AUTHEN FAIL
[02:26:32 030406] 192.168.001.089 AUTHEN SUCCESS
[02:26:32 030406] 192.168.001.074 AUTHOR FAIL
[02:26:32 030406] 192.168.001.089 AUTHOR SUCCESS
This example displays all TACACS+ specific counters and statistics.
[296] tacacs stats
TACACS+ Statistics
-------------------------
Connect Attempts:
Connect Failures:
0
0
Wrong Header Type:
0
0
0
0
Wrong Header Sequence Number:
Wrong Header Session ID:
Wrong Body Length:
Write Errors:
Read Errors:
0
0
0
0
Short Header Received:
Short Body Received:
Timed-out waiting for response: 0
[296]
Display Item
Description
Connect Attempts
Connect Failures
Wrong Header Type
Displays the number of attempts that were made to connect to
the TACACS+ server.
Displays the number of failed connection attempts that were
made to the TACACS+ server.
Displays the number of packets received from the TACACS+
server that had an invalid type.
Wrong Header
Sequence Number
Displays the number of packets received from the TACACS+
server that had a sequence number that was out of order.
9-97
AI296 Version 9.8x User’s Guide
AI296 Commands: tacacs
Display Item
Description (Continued)
Wrong Header
Session ID
Displays the number of packets received from the TACACS+
server that had an invalid session ID.
Wrong Body Length
Displays the number of packets received from the TACACS+
server that had a body length attribute that did not match the
actual length of body received.
Write Errors
Read Errors
Displays the number of errors that occurred when AI296
attempted to send a packet to the TACACS+ server.
Displays the number of errors that occurred when AI296
attempted to read a packet from the TACACS+ server.
Short Header
Received
Displays the number of incomplete headers that were received
when AI296 attempted to read a packet from the TACACS+
server.
Short Body
Received
Displays the number of packets with incomplete bodies that
were received when AI296 attempted to read them from the
TACACS+ server.
Timed-out waiting
for response
Displays the number of times AI296 timed out while waiting for
a response from the TACACS+ server. For information about
configuring the time out value, refer to command aaa on page
9-6.
9-98
AI296 Version 9.8x User’s Guide
AI296 Commands: tacacs server
tacacs server
Description
This command enables, disables, or removes the configuration for specified
TACACS+ servers.
Command Type
shell
Formats
config tacacs server
{ server_range | * } { disable | enable | default }
ip { server_range | * } { ip_address }
phase { server_range | * } { disable | enable }
{ account | all | authen | author }
port { server_range | * } { port_number }
secret { server_range | * } { shared_secret }
summary [ server_range | * ]
Parameters
*
Specifies all TACACS+ servers.
default
Disables all servers in the range and sets all configuration values
to their defaults.
disable
Disables the TACACS+ server or range of TACACS+ servers.
enable
Enables the TACACS+ server or range of TACACS+ servers.
ip
Configures an IP address for specified TACACS+ servers.
ꢀ
Note: AI296 does not prevent users from configuring multiple
server entries with the same IP address.
The following parameters are accepted:
z *—Specifies all TACACS+ servers.
z server_range—Specifies a server number or range of server
numbers.
z ip_address—Defines the server IP address.
9-99
AI296 Version 9.8x User’s Guide
AI296 Commands: tacacs server
phase
Configures the AAA phases that are allowed for specified
TACACS+ servers. The following parameters are accepted:
z *—Specifies all TACACS+ servers.
z account—Enables or disables the accounting phase for the
specified TACACS+ servers.
z all—Enables or disables all AAA phases for the specified
TACACS+ servers.
z authen—Enables or disables the authentication phase for the
specified TACACS+ servers.
z author—Enables or disables the authorization phase for the
specified TACACS+ servers.
z disable—Disables the specified AAA phases for the specified
TACACS+ servers.
z enable—Enables the specified AAA phases for the specified
TACACS+ servers.
z server_range—Specifies a server number or range of server
numbers.
port
Configures the TCP port number for specified TACACS+ servers.
The following parameters are accepted:
z *—Specifies all TACACS+ servers.
z port_number—Defines the TCP port number for the TACACS+
servers. Valid values are 1 through 65535.
z server_range—Specifies a server number or range of server
numbers.
secret
Configures the TACACS+ shared secret, which is similar to a
password, for specified TACACS+ servers. The following
parameters are accepted:
z *—Specifies all TACACS+ servers.
z shared_secret—Defines the TACACS+ shared secret for the
server or server range. The maximum length of the shared
secret is 24 characters.
z server_range—Specifies a server number or range of server
numbers.
summary
Displays a summary of TACACS+ server configuration settings for
specified servers. The following parameters are accepted:
z *—Specifies all TACACS+ servers.
z server_range—Specifies a server number or range of server
numbers.
9-100
AI296 Version 9.8x User’s Guide
AI296 Commands: tacacs server
server_range
Specifies a server number or range of server numbers. The server
number represents a server’s priority level. AI296 attempts to
contact all servers in the range starting with the lowest numbered
ones. If the connection to server #1 fails, AI296 will attempt to
contact server #2, and so on. Valid values are 1 to 9. Individual
values are separated by commas (,) and hyphens (-). For
example, 1,4-6 specifies servers 1, 4, 5, and 6.
Command Defaults
Disabled
Examples
The following TACACS+ server settings are configured for server numbers 1, 4, and 7:
z
z
z
z
z
Enabled TACACS+ servers
IP address 12.56.120.4
Disabled accounting phase
Port number 32500
Secret newguy.
[296] tacacs server 1,4,7 enable
[296] tacacs server ip 3 12.56.120.4
[296] tacacs server phase 1-5,8 disable account
[296] tacacs server port 7-9 32500
[296] tacacs server secret 8 newguy
This example displays all configured TACACS+ servers and server settings.
[296] tacacs server summary
Server IP Address
Port Secret
------ --------------- ----- ------------------------ ---------------------
Phases
+ 1
- 2
- 3
+ 4
- 5
- 6
+ 7
- 8
- 9
000.000.000.000
000.000.000.000
012.056.120.004
012.012.012.012
012.012.012.012
012.012.012.012
49
49
49
49
49
49
Authen Author
Authen Author
Authen Author
Authen Author
Authen Author
Authen Author Account
Authen Author Account
000.000.000.000 32500
000.000.000.000 32500
000.000.000.000 32500
newguy Authen Author
Authen Author Account
[296]
Display Item Description
Server
Displays the server numbers. The +/- signs indicate if the
associated servers are enabled (+) or disabled (-).
9-101
AI296 Version 9.8x User’s Guide
AI296 Commands: tacacs server
Display Item Description (Continued)
IP Address
Displays the configured TACACS+ IP addresses for the specified
TACACS+ servers.
Port
Displays the configured TACACS+ port numbers for the specified
TACACS+ servers.
Secret
Phases
Displays the TACACS+ shared secrets (passwords) for specified
TACACS+ servers.
Displays the AAA phases that are allowed for specified TACACS+
servers.
9-102
AI296 Version 9.8x User’s Guide
AI296 Commands: tail
tail
Description
This command displays the last few lines of a file.
Command Type
shell
Formats
tail [ -n lines ] file_name ...
ꢀ
Note: More than one file name can be specified in this command.
Parameters
-n
Specifies that a line number value will be entered.
lines
Defines the number of lines to display. The default is 20.
file_name
Defines the name of the file to display.
Examples
This example displays the last 10 lines of file userlog.txt.
[296]tail -n 10 userlog.txt
[14:09:46 072204] User pubs from 10.40.5.20#1309 has exited the shell.
[14:14:50 072204] User pubs from 10.40.5.20#1309 has entered the shell.
[16:17:53 072204] User pubs from 10.40.5.20#1309 has exited the shell.
[16:17:53 072204] User pubs from 10.40.5.20#1309 has logged out of the Destinat
ion Menu.
[16:27:23 072204] User pubs from 10.40.5.20#1565 has logged into the Destinatio
n Menu.
[16:27:25 072204] User pubs from 10.40.5.20#1565 has entered the shell.
[17:44:07 072204] User pubs from 10.40.5.20#1565 has exited the shell.
[17:44:18 072204] User pubs from 10.40.5.20#1565 has logged out of the Destinat
ion Menu.
[09:15:28 072304] User pubs from 10.40.5.20#1205 has logged into the Destinatio
n Menu.
[09:15:29 072304] User pubs from 10.40.5.20#1205 has entered the shell.
[296]
9-103
AI296 Version 9.8x User’s Guide
AI296 Commands: tcpoutconn
tcpoutconn
Description
This command controls how long outgoing TCP connections wait for a connection to
be established before failing.
Command Type
shell and winslc
Formats
For the shell command:
tcpoutconn [ timeout ]
For the winslc command:
winslc baseport tcpoutconn [ timeout ]
Parameters
timeout
Defines the length of the timeout. The range is 2 to 360 seconds. The
default is 75.
baseport
Defines the baseport number for AI296.
ꢀ
Note: In standalone mode, resetting AI296 resets the timeout to the default of 75.
Examples
This example displays the configuration of the TCP outgoing connection timer to 30
seconds.
[296]tcpoutconn 30
TCP Outgoing Connection Timer Value: 30
[296]
9-104
AI296 Version 9.8x User’s Guide
AI296 Commands: tftp
tftp
ꢀ
Note: This command is only available when AI296 is in standalone mode.
Description
This command downloads a file from the Trivial File Transfer Protocol (TFTP) server
to AI296 or uploads a file to the TFTP server from AI296.
The following rules apply when uploading or downloading a file:
z
z
File names must contain an extension of .ini, .img, .zmg, .cnf, or .txt.
Configuration files can be downloaded directly to file primary.cnf or to another .cnf
file.
z
z
z
The only .txt file allowed is banner.txt and the only .ini file allowed is boot.ini.
AI296 must be updated in order to run a downloaded image file.
Any .img filename is acceptable except boot.img, which is reserved, and
primary_devel.img, which is the primary image.
z
z
All .zmg files must be written to a destination file with a .img extension. If no
destination file name is given, the name will default to the source file name with a
.img extension.
The source and destination file names must have the same extension (excluding
.zmg files, which use a .img extension).
Command Type
shell
Formats
tftp
get [ address ] [ source_filename ] [ dest_filename ]
put [ address ] [ source_filename ] [ dest_filename ]
9-105
AI296 Version 9.8x User’s Guide
AI296 Commands: tftp
Parameters
get
Downloads a file from the TFTP server. The following parameters are
accepted:
z address—Defines the IP address of the TFTP server to which the file
download will occur.
z source_filename—Defines the file to download from the TFTP server.
ꢀ
Note: The source file name cannot contain spaces or special
characters.
z dest_filename—Defines the name of the source file after it has been
downloaded from the server. If no destination file name is specified, the
file will have the same name as the source file.
ꢀ
Note: The destination file name cannot contain spaces or special
characters.
put
Uploads a file to the TFTP server. The following parameters are accepted:
z address—Defines the IP address of the TFTP server to which the file
upload will occur.
z source_filename—Defines the file to upload to the TFTP server.
ꢀ
Note: The source file name cannot contain spaces or special
characters.
z dest_filename—Defines the name of the source file after it has been
uploaded to the server. If no destination file name is specified, the file will
have the same name as the source file.
ꢀ
Note: The destination file name cannot contain spaces or special
characters.
Examples
This example displays the upload of file primary.cnf to file secondary.cnf on TFTP
server 10.34.6.13.
[296] tftp put 10.34.6.13 primary.cnf secondary.cnf
File Uploaded successfully.
[296]
9-106
AI296 Version 9.8x User’s Guide
AI296 Commands: tftp
This example displays the download of file secondary.cnf to file primary.cnf from TFTP
server 10.34.6.13.
[296] tftp get 10.34.6.13 secondary.cnf primary.cnf
Attempting to Download the file secondary.cnf ...
File Downloaded successfully.
[296]
9-107
AI296 Version 9.8x User’s Guide
AI296 Commands: tftpboot
tftpboot
Description
This command displays the BOOTP/TFTP status or aborts attempts to contact the
BOOTP server. The AI296 card attempts to contact a BOOTP server if certain
conditions are met. These conditions are:
z
The card is in standalone mode.
AND
z
The card does not have an IP address set or no BOOT.INI file exists.
Attempts to contact the BOOTP server continue until a valid reply is received or until
the IP address gets set by the user in another manner, such as with an “ip init” shell
command.
ꢀ
Note: If the conditions are initially met, then the card will not attempt to contact the
BOOTP server.
When AI296 receives the necessary information from the BOOTP server, it attempts
to retrieve a configuration file from the TFTP server. The TFTP server information is
contained in the response from the BOOTP server.
Command Type
shell
Formats
tftpboot
Examples
This example displays the result of a card booting without a BOOTP/TFTP session.
[296]tftpboot
Usage: tftpboot [abort]
Displays BOOTP/TFTP status or aborts retry attempts.
BOOTP/TFTP did not run this session.
[296]
9-108
AI296 Version 9.8x User’s Guide
AI296 Commands: tftpboot
This example displays the result of a card booting when no BOOTP or TFTP server is
on the net.
[296] tftpboot
Usage: tftpboot [abort]
Displays BOOTP/TFTP status or aborts retry attempts.
Waiting for a response from the BOOTP server.
[296] tftpboot abort
BOOTP/TFTP retry attempts will be aborted.
[296]
This example displays the result of a boot when the BOOTP server is on the net but
the TFTP server is not available:
[296] tftpboot
Usage: tftpboot [abort]
Displays BOOTP/TFTP status or aborts retry attempts.
Waiting for a response from the TFTP server.
BOOTP Response:
IP Address: 10.48.60.11
TFTP Server: 10.48.60.1
TFTP File: 296v950b002.cnf
Subnet Mask: 255.255.0.0
Router: 10.48.0.1
[296]
This example displays the result of a reboot with a successful BOOTP/TFTP session:
[296]tftpboot
Usage: tftpboot [abort]
Displays BOOTP/TFTP status or aborts retry attempts.
BOOTP/TFTP is finished.
[296]
9-109
AI296 Version 9.8x User’s Guide
AI296 Commands: timezone
timezone
ꢀ
Note: This command is only available when AI296 is in standalone mode.
Description
This command displays or changes the time zone or adjusts the time to reflect
daylight savings.
Command Type
shell
Formats
timezone
-dstoff [ { + | - } hh:mm ]
-dston [ { + | - } hh:mm ]
Parameters
-dston
Enables daylight savings time for AI296. The following parameters are
accepted:
z
+—Specifies that the value is east of UTC.
-—Specifies that the value is west of UTC.
z
z hh—Defines the number of hours from UTC (Universal Coordinated
Time or Greenwich Mean Time).
z mm—Defines the number of minutes from UTC (Universal
Coordinated Time or Greenwich Mean Time).
-dstoff
Disables daylight savings time for AI296. The following parameters are
accepted:
z
+—Specifies that the value is east of UTC.
-—Specifies that the value is west of UTC.
z
z hh—Defines the number of hours from UTC (Universal Coordinated
Time or Greenwich Mean Time).
z mm—Defines the number of minutes from UTC (Universal
Coordinated Time or Greenwich Mean Time).
ꢀ
Note: For +/-, enter the direction (+ = east) (- = west) of Universal Coordinated Time
(UTC) or Greenwich Mean Time.
The time entered here is the number of hours from UTC. For example, if the
desired location is in the Eastern Standard Time (EST) zone, enter -05:00 in
this field. This indicates a time 5 hours behind UTC.
9-110
AI296 Version 9.8x User’s Guide
AI296 Commands: timezone
Examples
This example displays the current daylight savings time setting.
[296]timezone
Daylight saving is disabled on this system
Current time zone: +00:00
[296]
This example displays the enabling of daylight savings time and the setting of the
timezone to -5:00.
[296]timezone -dston
Daylight saving is enabled on this system
Current time zone: +00:00
[296]timezone -05:30
Daylight saving is enabled on this system
Current time zone: -05:30
[296]
9-111
AI296 Version 9.8x User’s Guide
AI296 Commands: trace
trace
Description
This command configures which X.25 rejected call codes (cause and diagnostic)
appear on the log port. This command can also be used to see the current trace level.
The default trace level is 3.
Command Types
shell and winslc
Formats
For the AI296 system command:
trace level
For the winslc command:
winslc baseport trace level
Parameters
baseport
Defines the baseport number for AI296.
level
Defines the minimum trace level on the log port. For example, if level
is set to 2, all X.25 events assigned a priority of 2 or higher will appear
on the log port. The valid range for this argument is 1 to 5. The default
level is 3.
ꢀ
Note: If you enter this command without a level, the current trace level number
appears.
Table 9-3 shows the priority assigned to each trace level.
Table 9-3 Trace Priority Levels
Priority
Level
X25_TRACE
X25_NORMAL
X25_MINOR
X25_MAJOR
X25_FATAL
1
2
3 (default)
4
5
9-112
AI296 Version 9.8x User’s Guide
AI296 Commands: trace
Examples
This example displays the configuration of trace 2.
[296]trace 2
X.25 Trace Level: 2
[296]
9-113
AI296 Version 9.8x User’s Guide
AI296 Commands: traceroute
traceroute
Description
This command diagnoses connectivity problems between AI296 and other hosts.
Command Type
shell
Formats
traceroute ip_address
Parameters
ip_address
Defines the IP address of the destination device in dotted decimal
format.
Examples
This example displays the traceroute to IP address 10.40.57.10.
[296]traceroute 10.40.57.10
traceroute to 10.40.57.10, 10.40.57.10, 30 hops max, 40 byte packets
1 10.40.57.10
[296]
9-114
AI296 Version 9.8x User’s Guide
AI296 Commands: type
type
Description
This command displays the text of any file other than a code image or configuration
file.
ꢀ
Note: This command has the same functionality as command cat.
Command Types
shell
Formats
type [ -p ] filename
Parameters
-p
Displays text from the file one page at a time.
filename
Defines the file for which you want to view the contents.
Examples
This example displays the first page of contents for file log.txt.
[296]type -p log.txt
Configuration has changed
06:20:11 060600 Sev=F Msg:
User pubs from 10.40.5.20#1436 has exited the shell.
06:20:20 060600 Sev=F Msg:
User pubs from 10.40.5.20#1436 has entered the shell.
06:21:01 060600 Sev=0 Msg:
Configuration has changed
06:21:04 060600 Sev=0 Msg:
Configuration has changed
06:21:04 060600 Sev=F Msg:
User pubs from 10.40.5.20#1436 has exited the shell.
06:21:07 060600 Sev=F Msg:
User pubs from 10.40.5.20#1436 has logged out of the Destination Menu.
04:40:49 060700 Sev=F Msg:
User pubs from 10.40.5.20#2729 has logged into the Destination Menu.
04:40:51 060700 Sev=F Msg:
User pubs from 10.40.5.20#2729 has entered the shell.
Press Space for more or q to quit:
9-115
AI296 Version 9.8x User’s Guide
AI296 Commands: update
update
Description
This command displays information about the image and configuration files. When
entered with arguments, this command updates AI296 software. Update the software
by copying a new image or configuration file to a destination file.
Command Types
shell and winslc
Formats
For the shell command:
update src_file dest_file
For the winslc command:
winslc baseport update src_file dest_file
Parameters
src_file
Defines the source file to copy.
dest_file
Defines the file where the source file is to be stored.
baseport
Defines the baseport number for AI296.
ꢀ
Note: The src_fileand the dest_filemust both have a file extension of either .cnf
or .img.
Examples
This example displays the update of source image file 296.imgto destination image file
boot.img.
[296]update 296.img boot.img
[296]
9-116
AI296 Version 9.8x User’s Guide
AI296 Commands: uptime
uptime
Description
This command displays the current time and the amount of time AI296 has been
running since it was last booted.
Command Type
shell
Formats
uptime
Examples
This example displays the current time and the amount of time AI296 has been
running since it was last booted.
[296]uptime
1:33pm up 2 days, 23:08:40
(uptime rolls over every 497 days, 2:27:52)
[296]
9-117
AI296 Version 9.8x User’s Guide
AI296 Commands: useradd
useradd
Description
This command adds a username and password. When the user first logs into AI296,
the login name and password are both aiby default. Five grace logins are available
before a username and password must be configured. A total of ten users can be
added to the database.
Command Type
shell
Formats
useradd [ -profile_name ] [ username ]
Parameters
profile_name
permissions. The default permission is supervisor.
username
Defines the login name for a user (up to 8 characters). After
entering a username, a prompt appears that asks for a password
(up to 10 characters).
Table 9-4 Description of Permissions
profile_name Permission
supervisor
Specifies a user who can execute all commands on the system. At
least one supervisor permission must be configured. The system
will not allow the deletion of the only supervisor user. The default
permission is supervisor.
mgmt
Specifies a user who can execute all commands except for
useradd.
9-118
AI296 Version 9.8x User’s Guide
AI296 Commands: useradd
Table 9-4 Description of Permissions (Continued)
profile_name Permission
status
Specifies a user who can only execute the following commands:
z creset
z debug
z diag-conn
z diag-info
z diag-eth
z diag-tconn
z help
z ip
z menu
z ping
z pvclist
z show
z staeia
z staslc
dest
Specifies a user who can login into AI296 and access the
destination menu. The user cannot connect to destination aito
retrieve status or to change the configuration.
connect
Specifies a user who is automatically connected to a specific
destination at login. The destination is specified when the
permission is assigned.
Examples
This example displays the addition of user brianwith profile mgmtto the user database.
The system prompts the user for the password after the username and profile are
entered.
[296]useradd -mgmt brian
Adding user of type 'mgmt'
Please enter a password.
Passwords are truncated at 10 characters.
Please retype the password.
User "brian" added successfully.
[296]
9-119
AI296 Version 9.8x User’s Guide
AI296 Commands: userdel
userdel
Description
This command deletes a username and password from the database.
Command Type
shell
Formats
userdel
Examples
This example displays the deletion of user brian from the database. After the
command is initially entered, prompts appear that tell the user what information needs
to be entered.
[296]userdel
Please enter the login name of the user to DELETE.
brian
Delete user "brian"? (y/n) y
User "brian" deleted successfully.
[296]
9-120
AI296 Version 9.8x User’s Guide
AI296 Commands: users
users
Description
This command displays currently configured AI296 users with the associated profile
names and destinations.
Command Types
shell
Formats
user
Examples
This example displays all currently configured AI296 users with associated profile
names and destinations. In this case, pubs is the only configured user.
[296] users
User Name
-----------------------------------------------
Profile Name
Destination
"pubs"
[296]
supervisor
9-121
AI296 Version 9.8x User’s Guide
AI296 Commands: who
who
Description
This command displays the users currently logged into AI296. It displays the user
name, time of login, user ID, the source of the connection, and command currently
being used by each user. The destination is shown only if the user has connected to
an alias with the destination menu.
Important: Do not use the ID displayed with this command to break a connection.
Command Type
shell
Formats
who
Examples
This example displays all the users currently logged in to the AI296. In this case, pubs
is the only logged in user.
[296]who
User
Login Time
------------------------------------------------------------------------------
ID From
Command (-> Destination)
"pubs"
[296]
Jul 23 09:15
76 10.40.5.20#1205
who
9-122
AI296 Version 9.8x User’s Guide
AI296 Commands: xvc
xvc
Description
This command displays information about a specific X.25 logical channel.
Command Types
shell and winslc
Formats
For the AI296 system command:
xvc link.circuit
For the winslc command:
winslc baseport xvc link.circuit
Parameters
baseport
Defines the baseport number for AI296.
link
Defines a number from 1 to 16.
circuit
Defines a valid, logical channel number.
Examples
This example displays the X.25 logical channel information for link 3 and circuit 1.
[296]xvc 3.1
VC state: DataTransfer, link state: L_connected, restarts 1-1 / 0-0
NSUat: 1.
[296]
9-123
AI296 Version 9.8x User’s Guide
AI296 Commands: xvc
9-124
AI296 Version 9.8x User’s Guide
AI296 System Codes: X.25 Cause Codes and Diagnostic Codes
X.25 Cause Codes and Diagnostic Codes
X.25 cause codes indicate events that triggered X.25 packets. Possible values for the
cause codes can vary depending on the type of packet (CLEAR REQUEST,
REGISTRATION CONFIRMATION, RESET REQUEST, or RESTART).
X.25 diagnostic codes provide additional tips about the nature of a specific problem.
Unlike cause codes, diagnostic codes do not vary depending on the type of packet.
ꢀ
Note: Diagnostic codes can be produced by any equipment that handles virtual
circuits and can propagate through all equipment that handles virtual circuits.
Because of this, diagnostic codes may not indicate a problem with AI296.
The following X.25 cause codes and diagnostic codes are available:
z
z
z
z
z
z
Standard Reset Indication Cause Codes
reset indication cause codes (in hexadecimal format) and their meanings.
Table A-1 Standard Reset Indication Cause Codes
Cause Code Description
0x00
0x01
0X03
0X05
0X07
0X09
0X0F
0X11
Remote DTE originated reset
Reset out of order
Reset due to remote procedure error
Reset due to local procedure error
Reset due to network congestion
Reset due to remote DTE operational
Reset due to network operational
Reset due to incompatible destination
A-2
AI296 Version 9.8x User’s Guide
AI296 System Codes: X.25 Cause Codes and Diagnostic Codes
Table A-1 Standard Reset Indication Cause Codes (Continued)
Cause Code Description
0X1D Reset due to network out of order
Kentrox-Specific Reset Indication Cause Codes
Reset indication cause codes apply to reset packets and are specific to Kentrox
hexadecimal format) and their meanings.
Table A-2 Kentrox-Specific Reset Indication Cause Codes
Cause Code Description
0x9B
Remote DTE originated reset
Standard Clear Indication Cause Codes
indication cause codes and their meanings.
Table A-3 Standard Clear Indication Cause Codes
Cause Code Description
0x00
0x01
0x03
0x05
0X09
0x0B
0X11
0x13
0x15
0X19
0X21
0X29
DTE originated
Number busy
Invalid facility request
Network congestion
Clear due to network out of order
Access barred
Remote procedure error
Local procedure error
Recognized Private Operating Agency (RPOA) out of order
Reverse charging not subscribed
Incompatible destination
Fast select not subscribed
A-3
AI296 Version 9.8x User’s Guide
AI296 System Codes: X.25 Cause Codes and Diagnostic Codes
Table A-3 Standard Clear Indication Cause Codes (Continued)
Cause Code Description
0x39
0x7F
Ship absent
Registration/cancellation confirmed
Standard ISO Diagnostic Codes
Table A-3 lists the standard ISO diagnostic codes and their meanings.
Table A-4 Standard Clear Indication Cause Codes
Cause Code Description
0xA0
0xA1
0xA2
0xA3
0xA4
0xA5
0xA6
0xA7
DTE specific signals
DTE operational
DTE not operational
DTE resource constraint
Fast select not subscribed
Invalid partially full data packet
D-bit procedure not supported
Registration/cancellation confirmed
CCITT Diagnostic Codes
Table A-3 lists the CCITT diagnostic codes and their meanings.
Table A-5 Standard Clear Indication Cause Codes
Cause Code Description
0x00
0x01
0x02
0x10
0x11
0x12
No additional information
Invalid P(S)
Invalid P(R)
Packet type invalid
Packet type invalid for state r1
Packet type invalid for state r2
A-4
AI296 Version 9.8x User’s Guide
AI296 System Codes: X.25 Cause Codes and Diagnostic Codes
Table A-5 Standard Clear Indication Cause Codes (Continued)
Cause Code Description
0x13
0x14
0x15
0x16
0x17
0x18
0x19
0x1A
0x1B
0x1C
0x1D
0x20
0x21
0x22
0x23
0x24
0x25
0x26
0x27
0x28
0x29
0x2A
0x2B
0x2C
0x2D
Packet type invalid for state r3
Packet type invalid for state p1
Packet type invalid for state p2
Packet type invalid for state p3
Packet type invalid for state p4
Packet type invalid for state p5
Packet type invalid for state p6
Packet type invalid for state p7
Packet type invalid for state d1
Packet type invalid for state d2
Packet type invalid for state d3
Packet type not allowed
Unidentifiable packet
Call on one-way logical channel
Invalid packet type on a permanent virtual circuit
Packet on unassigned logical channel
Reject not subscribed to
Packet too short
Packet too long
Invalid general format identifier
Restart or registration packet with non-zero LCN
Packet type not compatible with facility
Unauthorized interrupt confirmation
Unauthorized interrupt
Unauthorized reject
A-5
AI296 Version 9.8x User’s Guide
AI296 System Codes: X.25 Cause Codes and Diagnostic Codes
Table A-5 Standard Clear Indication Cause Codes (Continued)
Cause Code Description
0x30
0x31
0x32
0x33
0x34
0x40
0x41
0x42
0x43
0x44
0x45
0x46
0x47
0x48
0x49
0x4A
0x4B
0x4C
0x4D
0x50
0x51
0x52
0x53
Timer expired
Timer expired for incoming call
Timer expired for clear indication
Timer expired for reset indication
Timer expired for restart indication
Call set up, call clearing, or registration problem
Facility/registration code not allowed
Facility parameter not allowed
Invalid called address
Invalid calling address
Invalid facility/registration length
Incoming call barred
No logical channel available
Call collision
Duplicate facility request
Non-zero address length
Non-zero facility length
Facility not provided when expected
Invalid CCITT-specified DTE facility
Miscellaneous
Improper cause code from DTE
Not aligned octet
Inconsistent Q-bit setting
A-6
AI296 Version 9.8x User’s Guide
AI296 System Codes: X.25 Cause Codes and Diagnostic Codes
Kentrox-Specific Diagnostic Codes
Kentrox-specific diagnostic codes provide tips about the nature of a specific problem.
Table A-6 lists the Kentrox-specific diagnostic codes and their meanings.
Table A-6 Kentrox-specific Diagnostic Codes
Cause Code Description
0x85
0x86
0x87
0x88
0x89
PVC attach error
Connection listen error
Not used
Internal connection ID not found
Memory resource error
A-7
AI296 Version 9.8x User’s Guide
AI296 System Codes: Crash Codes
Crash Codes
Crash codes report to the log port when a card crashes and you receive an AIswitch
fault message. This message indicates that the system has detected a serious
hardware or software fault.
Common Crash Codes
These codes are common to all software (not just Kentrox products). The first column
column displays the decimal value for the same message. The third column provides
a description of the error message. Contact Kentrox Technical Support to report any
of the following crash codes.
Table A-7 Common Crash Codes
Error Code
Hexadecimal Decimal
Error Code
Description
0001
0002
0003
0004
0005
0006
0007
0008
0009
09xx
1
Specifies a bus error.
2
Specifies an address error.
Specifies an illegal instruction.
Specifies a zero divide error.
Specifies a check instruction trap.
Specifies a TRAPV error.
3
4
5
6
7
Specifies a privilege error.
Specifies a trace trap.
8
9
Specifies an unused exception vector.
>264
Specifies an illegal vector. xx is the vector number
(non-zero) used in place of the codes above to
ensure that the exact vector number is determined
if an exception occurs.
A-8
AI296 Version 9.8x User’s Guide
AI296 System Codes: Crash Codes
AI296 Crash Codes
Support to report any of the following crash codes.
Table A-8 AI296 Crash Codes
Error Code
Hexadecimal Decimal
Error Code
Description
0020
0021
0022
0023
0024
0025
0026
0027
0028
32
33
34
35
36
37
38
39
40
Specifies a failure to free resource (streams).
Specifies a failure to free memory (system).
Specifies a failure of resource allocation (streams).
Specifies a failure of memory allocation.
Specifies a checksum error.
Specifies that a panic message has been printed.
Specifies an attempt to boot while up.
This code is not used.
Specifies that AI296 has been halted by Central
Switch command. This code is seen when you enter
command stpslcfor a card.
0030
0031
0032
0033
0034
0035
0036
0037
0038
0039
48
49
50
51
52
53
54
55
56
57
Specifies a crash in the shell.
Specifies a crash in transport layer multiplexing.
Specifies a crash in association daemon.
Specifies a crash in bootp.
Specifies a crash in X.25.
Specifies a crash in an asynchronous driver.
Specifies a crash in the PVC daemon.
Specifies a crash in the config daemon.
Specifies a generic stream error.
Specifies a crash in the AEP or AEPN protocol
processing option.
003A
58
Specifies a crash in the pktmod or TL1mod protocol
processing option.
A-9
AI296 Version 9.8x User’s Guide
AI296 System Codes: Crash Codes
Table A-8 AI296 Crash Codes (Continued)
Error Code
Hexadecimal Decimal
Error Code
Description
00AA
00AC
00AD
170
172
173
Specifies a serious memory error (unable to allocate
system memory).
Specifies that a serial communication controller is
not responding.
Specifies a software download. This is normal to
see when doing a software update to AI296.
System Failure Crash Reports
Crash codes report to the log port when a card crashes and you receive an AIswitch
fault message. This message indicates that the system has detected a serious
hardware or software fault.
A message similar to the following appears:
SLC has CRASHED - registers to follow:
Crash Code= 000000ad
PC= 00000000
SP= 00000000
IMMR= 00000000
MSR= 00000000
GPR00= 00000000
GPR03= 00000000
GPR06= 00000000
GPR09= 00000000
GPR12= 00000000
GPR15= 00000000
GPR18= 00000000
GPR21= 00000000
GPR24= 00000000
GPR27= 00000000
GPR30= 00000000
CR= 00000000
GPR01= 00000000
GPR04= 00000000
GPR07= 00000000
GPR10= 00000000
GPR13= 00000000
GPR16= 00000000
GPR19= 00000000
GPR22= 00000000
GPR25= 00000000
GPR28= 00000000
GPR31= 00000000
SSR0= 00000000
GRP02= 00000000
GRP05= 00000000
GRP08= 00000000
GRP11= 00000000
GRP14= 00000000
GRP17= 00000000
GRP20= 00000000
GRP23= 00000000
GRP26= 00000000
GRP29= 00000000
SSR1= 00000000
LR= 00000000
PVR= 00500000
XER= 00000000
PSOS1=00000000
CTR= 00000000
PSOS2=00000000
PSOS3= 00000000
A-10
AI296 Version 9.8x User’s Guide
AI296 System Codes: Kentrox Technical Support
Kentrox Technical Support
Some alarm conditions and crash codes reveal serious problems for which you
should contact Kentrox Technical Support. If one of these alarm conditions or crashes
should occur, record relevant information associated with the problem and contact
Kentrox Technical Support.
Phone:
Kentrox Technical Support (866) 480-3571
Kentrox Operator (toll-
free)
(800) 247-9482
Kentrox Operator
(international)
(614) 798-2000
Email:
Kentrox Technical
Support
When you send email to Kentrox, be sure to include your name, company name, and
telephone number.
A-11
AI296 Version 9.8x User’s Guide
AI296 System Codes: Kentrox Technical Support
A-12
AI296 Version 9.8x User’s Guide
Standalone Mode and Switch Mode: Standalone Mode
Standalone Mode
Standalone mode refers to the mode where AI296 stores its configuration locally (to
flash) or on a TFTP server. The CLC might be used as the TFTP server in some
cases. This lets the card operate as a self-contained unit. When operating in
standalone mode, AI296 has a local menu system that is used instead of the AI198
menu system for tasks such as alias and IP configuration. AI296 operates in
standalone mode when it is installed in the AI110 chassis.
The following characteristics apply when AI296 is operating in standalone mode:
z
z
The front panel Ethernet port is the default (rather than the IRB).
AI296 cards are not hot-swappable—the card configuration must be set up
manually.
z
z
AI296 has a unique system OID.
The AI296 local menu system has slightly different options than when the card is
running in switch mode.
Downloading Software for a Standalone AI296
To download software for AI296 in standalone mode:
1. Open a command prompt window.
2. At the command prompt, start the FTP utility:
ftp
3. At the FTP prompt, open AI296:
open ip_address
ip_address
Specifies the AI296 IP address.
The FTP utility prompts you for a user name and password.
4. Put the FTP utility in binary mode:
binary
5. Transfer the software image to AI296:
put filepath/imagename.img
filepath
Defines the path to the software image file.
imagename
Defines the software image file name.
ꢀ
Note: Wait for a completion message after entering this command.
B-2
AI296 Version 9.8x User’s Guide
Standalone Mode and Switch Mode: Standalone Mode
6. Exit the FTP utility.
7. Login to the shell with a serial or Telnet connection.
8. Update the existing boot program image with the new software image file:
update imagename.img boot.img
imagename
Defines the software image file name.
9. When the update is complete, reboot AI296.
Configuring BOOTP/TFTP
The AI296 configuration can be automatically downloaded from a TFTP server when
the card is in standalone mode and has BOOTP information stored in AI198 Menu 10.
For more information about BOOTP configuration, refer to “Configuring the BOOTP
Table” in the AI198 Common Logic Controller System Manager/User’s Manual.
When AI296 starts, it determines if the following conditions are met before using
BOOTP to find IP address information:
z
z
AI296 is in standalone mode
The IP address is not set.
If both of these conditions are met, AI296 attempts to contact a BOOTP server until it
obtains valid IP address information or the IP address is set by a user with the
ip initshell command. When an IP address has been obtained either by BOOTP or
The following events occur when AI296 attempts to download a configuration file from
the TFTP server:
z
Once the IP address information has been correctly configured from the BOOTP
reply, AI296 will attempt to contact a TFTP server only if the TFTP server IP
address and configuration filename were received by the BOOTP reply.
z
z
AI296 will try to download the configuration file from the TFTP server once every
60 seconds for a maximum of 10 retries.
If no valid configuration file is downloaded from the TFTP server after 10 retries,
AI296 will remove the previously configured IP address information from the
BOOTP server and completely restart the BOOTP process.
z
z
If at any time the local configuration file stored on flash is changed by a user,
AI296 will stop attempting to contact the TFTP server.
If a valid configuration is successfully downloaded from the TFTP server, AI296
will update the current configuration with the downloaded file.
B-3
AI296 Version 9.8x User’s Guide
Standalone Mode and Switch Mode: Switch Mode
Switch Mode
Switch mode refers to the mode where AI296 is managed by the CLC. When AI296 is
in switch mode, the AI198 menu system must be used to configure IP addresses,
aliases, IP static routes, and SNMP traps. AI296 must be located in the AI130 or
AI180 chassis to operate in switch mode.
The following characteristics apply when AI296 is operating in switch mode:
z
AI296 gets its configuration from the CLC at boot time (instead of locally or by
TFTP).
z
z
z
The CLC is used to route calls and maintain alias configuration information.
The IRB is the default port (rather than the front panel Ethernet port).
AI296 cards are hot-swappable—the card configuration does not have to be set
up manually.
z
The banner must be less than 1024 characters.
ꢀ
Note: Switch mode may also be referred to as CLC mode.
Downloading Software for AI296 in Switch Mode
To download software for AI296 when it is in switch mode:
1. Open a command prompt window.
2. At the command prompt, start the FTP utility:
ftp
3. At the FTP prompt, open AI198:
open ip_address
ip_address
Specifies the AI198 IP address.
The FTP utility prompts you for a user name and password.
4. Put the FTP utility in binary mode:
binary
B-4
AI296 Version 9.8x User’s Guide
Standalone Mode and Switch Mode: Switch Mode
5. Transfer the software image to AI198:
put filepath/imagename.img
filepath
Defines the path to the software image file.
imagename
Defines the software image file name.
ꢀ
Note: Wait for a completion message after entering this command.
6. Exit the FTP utility.
7. Log in to AI198.
8. At the command prompt, update AI296 with the new software image:
winslc baseport update
baseport
Defines the baseport of AI296.
ꢀ
Note: You can watch the download process by entering CTRL+L.
9. Wait for the completion message.
B-5
AI296 Version 9.8x User’s Guide
Standalone Mode and Switch Mode: Switch Mode
B-6
AI296 Version 9.8x User’s Guide
Commands for AI296 TACACS+ Server Enhancements: AI296 Commands
AI296 Commands
Important: To authorize a command with no additional arguments, remember to
enter permit ^$in the argument list.
The following AI296 commands can be included in an authorization set on the
TACACS+ server:
2401
pvclist
queue
ip
aaa
ai
alarm
arp
link
log
break
cat
logout
ls
clear
crash
crc
reset
rm
selcnf
sholog
show
creset
date
debug
del
snmp
id
delete
diag-conn
diag-eth
diag-info
diag-line
diag-tconn
dir
sonic
staeia
standalone
staslc
syncflash
tacacs
tail
exit
task
head
tcpoutconn
tftp
help
memory
memtrack
menu
tftpboot
timezone
type
modmux
more
update
uptime
useradd
userdel
users
who
passwd
ping
pppstatus
profile
The following keyword lets users access destinations:
dest
Provides authorization at the destination menu. Individual destination
names can be used as arguments. For example, {permit AI, permit
somedestination, permit EXIT}.
C-2
AI296 Version 9.8x User’s Guide
Commands for AI296 TACACS+ Server Enhancements: AI296 Menu Aliases
AI296 Menu Aliases
The following AI296 menu aliases can be included in an authorization set on the
TACACS+ server. Authorization occurs when level 1 menu items are traversed:
menu
Provides access to the menu.
menu_alias
Provides read access to the Alias menu.
menu_alias write
Provides write access to the Alias menu.
menu_link
Provides read access to the Link menu.
menu_link write
Provides write access to the Link menu.
menu_ipx
Provides read access to the IP Over X.25 Subnet menu.
menu_ipx write
Provides write access to the IP Over X.25 Subnet menu.
menu_route
Provides read access to the Static route menu.
menu_route write
Provides write access to the Static route menu.
menu_system
Provides read access to the System menu.
menu_system write
Provides write access to the System menu.
ꢀ
Note: Keyword writeis treated as an argument.
C-3
|