30" (76.2 cm) and 36" (91.4 cm) Sealed Gas Cooktop
PRODUCT MODEL NUMBERS
JGC8430CD JGC8536BD
PRODUCT DIMENSIONS – 30" MODEL (JGC8430CD)
E
F
Gas supply: The installation of this appliance
must conform with local codes or, in the
absence of local codes, with the National Fuel
Gas Code, ANSI Z223.1-Latest Edition, or, in
Canada, CAN/CGA-B149 Installation Code,
Latest Edition.
J
MANIFOLD
ENTRANCE
All supply piping, except as noted, should use
common National Pipe Thread (N.P.T.). For all
pipe connections use an approved pipe joint
compound resistant to the action of LP gas.
This appliance is designed for use with the
appliance gas pressure regulator supplied with
this appliance. It must be installed in the gas
line ahead of the gas manifold entrance. It is
preset for use with natural gas and must be
converted, as described in the Installation
Instructions for use with LP gas.
This appliance is designed to operate at a
pressure of 5" of water column on natural gas
or, if converted for use with LP gas (propane
or butane), 10" water column. Make sure this
appliance is supplied with and adjusted for the
type of gas for which it is designed.
This appliance was adjusted at the factory for
use with natural gas. If, at any time, this
appliance is to be used with a different type of
gas, all of the conversion adjustments
B
A
C
G
D
I
H
Dimensions
28-3/4" (73.0 cm)
20-5/8" (52.4 cm)
2" min.
5-1/16" (12.9 cm)
30" (76.2 cm)
21-3/4" (55.2 cm)
3-11/16" (9.4 cm)
12-7/16" (31.6 cm)
"A"
"B"
"C"
"D"
"E"
"F"
"G"
"H"
"I"
(5.1 cm)
IMPORTANT: Cutout
dimensions are critical.
Dimensions must be measured
and cut accurately to within
1/16" (0.2 cm) to ensure
proper fit.
1-3/4"
1-3/4"
(4.4 cm)
(4.4 cm)
"J"
described in the Installation Instructions must
be made by a qualified service technician
before attempting to operate the cooktop on
that gas. Natural gas should be supplied to the
appliance pressure regulator at a line pressure
between 6" and 14" of water column or, if
converted for LP gas, between 11" and 14".
PRODUCT DIMENSIONS – 36" MODEL (JGC8536BD)
E
F
Make the gas connection to the inlet of the
appliance pressure regulator with 1/2" NPT
male pipe threads.
J
MANIFOLD
ENTRANCE
Install a manual shut-off valve in an accessible
location in the gas line ahead of the appliance
pressure regulator and external to this
appliance for the purpose of turning on or
shutting off gas to the appliance.
Make additional pipe connections as necessary
ahead of the shut-off valve to the gas supply
source. Assure all pipe joint connections are
gas tight.
B
D
A
I
H
C
Electrical: See page 2.
Dimensions
"A"
"B"
"C"
"D"
"E"
"F"
"G"
"H"
"I"
34-7/8" (88.6 cm)
20-13/16" (52.9 cm)
2" min.
4-9/16" (11.6 cm)
36" (91.4 cm)
(5.1 cm)
21-9/16" (54.8 cm)
3-13/16" (9.6 cm)
15-1/2" (39.4 cm)
IMPORTANT: Cutout
dimensions are critical.
Dimensions must be measured
and cut accurately to within
1/16" (0.2 cm) to ensure
proper fit.
1-3/4"
1-3/4"
(4.4 cm)
(4.4 cm)
"J"
Page 1 of 2
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Ref. 8101P643-60
09-26-08
|