COLOR VIDEO MONITOR
BEDIENUNGSANLEITUNG : FARB-VIDEO-MONITOR
MANUEL D’INSTRUCTIONS : MONITEUR VIDEO COULEUR
MANUALE DI ISTRUZIONI : MONITOR VIDEO A COLORI
INSTRUCCIONES : MONITOR DE VIDEO A COLOR
INSTRUCTIONS
TM-H150CG
For Customer Use:
Enter below the Serial No. which is located on the rear of the cabinet.
Retain this information for future reference.
Pour l’usage du client:
Enter ci-dessous le numéro de série qui est situé sur l’arrière du coffret.
Conserver cette information pour une référence ultérieure.
Model No. :
Numéro de modèle :
Serial No. :
Numéro de série :
LCT1564-001A-H
SAFETY PRECAUTIONS
In order to prevent any fatal accidents caused by misoperation
FCC INFORMATION (U.S.A. only)
CAUTION: Changes or modification not approved by
JVC could void the user's authority to operate the
equipment.
or mishandling the monitor, be fully aware of all the following
precautions.
WARNINGS
To prevent fire or shock hazard, do not expose this
monitor to rain or moisture. Dangerous high voltages
are present inside the unit. Do not remove the back
cover of the cabinet. When servicing the monitor,
consult qualified service personnel. Never try to service
it yourself.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and
receiver.
WARNING : THIS APPARATUS MUST
BE EARTHED.
Improper operations, in particular alternation of high
voltage or changing the type of tube may result in x-ray
emission of considerable dose. A unit altered in such a
way no longer meets the standards of certification, and
must therefore no longer be operated.
This monitor is equipped with a 3-blade grounding-type
plug to satisfy FCC rule. If you are unable to insert the
plug into the outlet, contact your electrician.
– Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV
technician for help.
Notice (U.S.A. only)
This product utilizes both a Cathode Ray Tube (CRT) and
other components that contain lead. Disposal of these
materials may be regulated in your community due to
environmental considerations. For disposal or recycling
information please contact your local authorities, or the
Electronics Industries Alliance: <http://www.eiae.org.>
PRECAUTIONS
● Use only the power source specified on the unit.
(120 V AC/220 – 240 V AC, 50 Hz/60 Hz)
● When not using this unit for a long period of time, or when
cleaning it, be sure to disconnect the power plug from the
AC outlet.
● Unplug this unit from the AC outlet and refer servicing to
qualified service personnel under the following conditions:
– when the power cord is frayed or the plug is damaged,
– if liquid has been spilled into the unit,
– if the unit has been dropped or the cabinet has been
damaged,
● Do not allow anything to rest on the power cord. And do not
place this unit where people will tread on the cord. Do not
overload wall outlets or power cords as this can result in a
fire or electric shock.
● Avoid using this unit under the following conditions:
– in extremely hot, cold or humid places,
– in dusty places,
– near appliances generating strong magnetic fields,
– in places subject to direct sunlight,
– in badly ventilated places,
– when the unit exhibits a distinct change in performance.
● Do not attempt to service this unit yourself as opening or
removing covers may expose you to dangerous voltage or
other hazards. Always refer servicing to qualified service
personnel.
● When replacement parts are required, have the service
personnel verify in writing that the replacement parts he/
she uses have the same safety characteristics as the
original parts. Use of manufacture’s specified replacement
parts can prevent fire, shock, or other hazards.
● Upon completion of any servicing or repair work to this unit,
please ask the service personnel to perform the safety
check described in the manufacturer’s service literature.
● When this unit reaches the end of its useful life, improper
disposal could result in a picture tube implosion. Ask
qualified service personnel to dispose of this unit.
– in automobiles with doors closed.
● Do not cover the ventilation slots while in operation as this
could obstruct the required ventilation flow.
● When dust accumulates on the screen surface, clean it with
a soft cloth.
2
POWER CONNECTION
The power supply voltage rating of this product is AC 120 V (For U.S.A. and Canada only) and AC 220 – 240 V (For European
countries or United Kingdom), the power cord attached conforms to the following power supply voltage and countries. Use only the
power cord designated to ensure Safety and EMC regulations of each countries.
Power cord
Power supply voltage : AC 120 V
AC 220 – 240 V
European countries
AC 220 – 240 V
United Kingdom
Countries
: U.S.A. and Canada
Warning:
● Do not use the same Power Cord for AC 120 V as for AC 220 – 240 V. Doing so may cause malfunction, electric shock
or fire.
Note for the United Kingdom power cord only
The plug on the United Kingdom power cord has a built-in fuse. When replacing the fuse, be sure to use only a correctly rated
approved type, re-fit the fuse cover.
(Consult your dealer or qualified service personnel.)
How to replace the fuse
Open the fuse compartment with the blade screw driver, and
replace the fuse.
(* An example is shown in the illustration.)
Fuse
SCREEN BURN
● It is not recommended to keep a certain still image displayed on screen for a long time as well as displaying extremely bright
images on screen. This may cause a burning (sticking) phenomenon on the screen of cathode-ray tube. This problem does not
occur as far as displaying normal video playback motion images.
Ⅵ Supplementary Explanation
= Information for monitor operation =
This monitor uses a high precision CRT (cathode ray tube). Please follow the procedures below.
* For stable operation of the CRT, approximately 30 minutes running time is required from the time the power is turned on.
* When the monitor is installed, it can be easily affected by surrounding magnetic fields, which can generate irregular color
on the screen. When it is difficult to eradicate, degauss from outside using a degausser, etc.
Contents
SAFETY PRECAUTIONS ................................................................................. 2
Controls and Features .................................................................................... 4
Front Panel .................................................................................................... 4
Rear Panel..................................................................................................... 6
Input Card (option)......................................................................................... 7
Preparation ...................................................................................................... 9
Installing the Input Card................................................................................. 9
Basic Menu Operations (MENU, SET-UP MENU)............................................................... 10
How to Use MENU ......................................................................................... 12
How to Use SET-UP MENU ........................................................................... 13
How to Use the External Control.................................................................. 15
Troubleshooting ............................................................................................ 16
Specifications ................................................................................................ 18
3
Controls and Features
Front Panel
1
2
3
4
5 6 7 8
9
p
q
w
1 CHROMA ( : Chroma)/PHASE (
: Phase)
3 VOLUME/SELECT (– +) buttons
Adjusts the volume.
button*
These buttons are also used to select the items on
the menu screen while the menu screen is
displayed.
• Pressing + or – button displays the VOLUME level bar on
the screen. Pressing + or – button while the level bar
appears on the screen allows you to adjust the volume.
(00 to 50)
• The VOLUME level bar disappears if no operation has
been done for about 10 seconds.
• The VOLUME level bar also disappears if you press
MENU button.
Press this button to activate the Chroma (picture
color density) adjustment mode or the Phase
(picture hue) adjustment mode. Each time you
press the button, the adjustment modes change.
Chroma“Phase
Adjust the value with the VOLUME/SELECT
(– +) buttons while the level bar appears on the
screen.
(–40 to +40)
• CHROMA is not adjustable when the RGB signal, black-
and-white signal, or no signal is input (except the
component signal).
• Adjusting CHROMA to “–40” is chroma off.
• PHASE is adjustable only when the NTSC signal is input.
4 MENU button
Displays MENU.
\ For details, see page 10.
NOTE:
fi button (while the menu screen is displayed)
Selects the items on the menu screen.
To display SET-UP MENU, press the fi button while holding down
the MENU button.
2 CONTRAST ( :Contrast)/
BRIGHT ( :Brightness) button*
Press this button to activate the picture contrast
adjustment mode or picture brightness adjustment
mode. Each time you press the button, the
adjustment modes change.
5 UNDER SCAN button
Reduces the screen size to display the entire
image.
• The button lights while this function is activated.
• Pressing the button again restores the screen to normal
size.
Contrast“Brightness
6 COLOR OFF button
Adjust the value with the VOLUME/SELECT
(– +) buttons while the level bar appears on the
screen.
Cuts color signals to display a black and white
image.
Use this function to check noises in the luminance
signal or to check the white balance adjustment.
(–40 to +40)
• The button lights while this function is activated.
• Pressing the button again restores the normal screen.
% button (while the menu screen is displayed)
Selects the items on the menu screen.
NOTE:
This function is not available to the RGB signal.
*While adjusting the picture,
• The adjustment level bar disappears if no operation has
been done for about 10 seconds.
• The adjustment level bar also disappears if you press
MENU button.
• “NO EFFECT” will appear for about 3 seconds if the
function you select has no effect.
4
7 BLUE CHECK button
8 ASPECT button
Displays only the blue signals.
Changes the aspect ratio from 4:3 to 16:9.
• The button lights while this function is activated.
• The button lights while the aspect ratio is 16:9.
• Pressing the button again restores the normal screen.
• Pressing the button again returns the aspect ratio to 4:3.
By using this function with the standard color-bar
currently used, you can check if CHROMA (picture
color density) or PHASE (picture hue) is adjusted
properly.
Also you can check if “COMPO. LEVEL” (the
adjustment level of the component signal) is
adjusted properly for the component signal or the
SDI signal.
9 INPUT SELECT buttons
Select an input to display.
A: Select the video signal input to the VIDEO A terminal
and the audio signal input to the AUDIO A terminal.
B: Select the video signal input to the VIDEO B terminal
and the audio signal input to the AUDIO B terminal.
\ When both an Y/C (S-video) signal and a composite signal
are input to the VIDEO B terminal, the Y/C signal has
priority over the composite signal.
NOTE:
C/D (SLOT):
This function is not available to the RGB signal.
Select the signal input to the input card installed in the
input card slot on the rear panel.
\ For details about how to select the input signal through the
1 Display the standard color-bar currently used
on the screen.
input card, see pages 7 and 8.
2 Press the BLUE CHECK button.
The following display appears on the screen.
• The corresponding button of the input currently selected
lights up.
p Power lamp
Unlit:
The main power is off.
Orange: The main power is on and the monitor is in stand-
by mode.
Green: The monitor is on.
3 If the brightness of the blue bars on the left
and right sides are the same, CHROMA
(picture color density) is adjusted properly.
q Stand-by button
Turns on and off the monitor when the main power
is on.
• For the component signal or the SDI signal, if the
brightness of the blue bars on the left and right sides
are the same, “COMPO. LEVEL” is adjusted properly.
NOTE:
You can set the delay time between when the stand-by button is
pressed and when the monitor actually turns on. See “RUSH
DELAY” on page 12.
4 If the brightness of two blue bars in the
middle are the same, PHASE (picture hue) is
adjusted properly.
w Speaker
A built-in speaker is on the side panel.
• PHASE should be checked only when the NTSC
signal is being input.
If the brightness of each blue bar is different, make the
following adjustment in the blue checking state:
When the composite signal or theY/C (S-video) signal is being
input:
By using the CHROMA/PHASE button and the VOLUME/SELECT
(– +) buttons, adjust CHROMA or PHASE so that brightness of the
blue bars on the left and right sides are the same.
When the component signal or SDI signal is being input:
Press the MENU button to display MENU, select “COMPO. LEVEL” by
pressing the %/fi buttons.
Then, adjust “COMPO. LEVEL” by pressing the VOLUME/SELECT
(– +) buttons so that brightness of two blue bars in the middle are
the same.
• Be sure to adjust CHROMA for the composite signal or theY/C
(S-video) signal before adjusting “COMPO. LEVEL.”
If you change the CHROMA adjustment for other signal formats
than the component signal after “COMPO. LEVEL” has been
adjusted, you need to adjust “COMPO. LEVEL” again.
5
Controls and Features (cont’d)
Rear Panel
e
SLOT
i
REMOTE
o
r
t
MAKE/
TRIGGER
;
POWER
y
u
a
e VIDEO A terminal
u AUDIO B terminal
Input (IN) and output (OUT) terminals for composite
signals.
Input (IN) and output (OUT) terminals for analog
audio signals.
• The IN and OUT terminals are bridge-connected (auto
• The IN and OUT terminals are bridge-connected (auto
termination).
termination).
NOTE:
NOTE:
Use the AUDIO A terminals for the corresponding audio signals.
Use the VIDEO B terminals for the corresponding video signals.
r VIDEO B terminal
i Input card slot
Input (IN) and output (OUT) terminals for composite
signals.
When using the input card (not supplied), install the
card to this slot.
• The IN and OUT terminals are bridge-connected (auto
termination).
o REMOTE (external control) terminal
Terminals for controlling the monitor by an external
NOTE:
Use the AUDIO B terminals for the corresponding audio signals.
control.
\ For details, see page 15.
t VIDEO B (Y/C IN,Y/C OUT) terminal
Input (IN) and output (OUT) terminals for Y/C (S-
video) signals.
; Main power switch
Turns on and off the main power.
• The Y/C IN and Y/C OUT terminals are bridge-connected
• I: ON
‡: OFF
(auto termination).
NOTE:
When turning on the main power, the power lamp lights up as
follows:
• Orange: The monitor is in stand-by mode.
• Green: The monitor is on.
NOTES:
• Use the AUDIO B terminals for the corresponding audio signals.
• When both an Y/C (S-video) signal and a composite signal are
input to the VIDEO B terminal, the Y/C signal has priority over
the composite signal.
a AC inlet
y AUDIO A terminal
Connect the supplied AC power cord to this inlet
and an AC outlet (120 V AC/220 – 240 V AC, 50 Hz/
60 Hz).
Input (IN) and output (OUT) terminals for analog
audio signals.
• The IN and OUT terminals are bridge-connected (auto
termination).
NOTE:
Use the VIDEO A terminals for the corresponding video signals.
6
Input Card (option)
7 Component/RGB Input Card (IF-C01COMG)
1 Component/RGB signal input/output terminals
Input (IN) and output (OUT) terminals for the component (color
difference) or the RGB signal.
G/Y
To select Component signal: Press the INPUT SELECT C button.
IN
B/P
OUT
/B-Y
B
R
To select RGB signal:
Press the INPUT SELECT D button.
1
• The IN and OUT terminals are bridge-connected (auto termination).
IN
R/P
OUT
/R-Y
2 Connection terminal
IN
IN
IN
OUT
OUT
OUT
Attach to the connection terminal of the input card slot on the
monitor.
2
3
HD/C
VD
S
3 Synchronized signal input/output terminals
Input (IN) and output (OUT) terminals for the vertical, horizontal or
complex synchronized signals.
AUDIO
4
• The IN and OUT terminals are bridge-connected (auto termination).
IN
OUT
NOTE:
These terminals are available only to the RGB input.
4 Audio signal input/output terminals
7 Acceptable signal formats when installed
on this monitor:
525/60i, 625/50i
Input (IN) and output (OUT) terminals for the analog audio signals.
• The IN and OUT terminals are bridge-connected.
• G on SYNC cannot be used with the
RGB input.
NOTE:
You cannot connect both the component signal outputs and the RGB signal outputs at a
time.
7 SDI Input Card (IF-C01SDG)
1 SWITCHED OUT terminal
Output (OUT) terminal for the re-clocked signal.The input signal from
the input terminal currently selected (SDI 1 or SDI 2) is re-clocked
and output from this terminal.
SWITCHED
OUT
1
NOTES:
• No signal is output from the SWITCHED OUT terminal when the main power is turned
off.
• Even when the input signal is switched from the SDI Input Card, the SWITCHED OUT
terminal still outputs the SDI 1 or SDI 2 re-clocked signal which is selected last time.
The re-clocked signal from SDI 1 is output from the SWITCHED OUT terminal when
the monitor is in stand-by mode.
IN
IN
SDI 1
SDI 2
2
3
2 D1 SDI signal input terminal (SDI 1, SDI 2)
Accepts the SMPTE259M D1 SDI signal.The audio signal of the
EMBEDDED AUDIO signal cannot be decoded (only the video signal
can be decoded).
AUDIO1
IN
OUT
4
AUDIO2
To select SDI 1: Press the INPUT SELECT C button.
To select SDI 2: Press the INPUT SELECT D button.
3 Connection terminal
7 Acceptable signal formats when installed
Attach to the connection terminal of the input card slot on the
monitor.
on this monitor:
525/60i, 625/50i
4 Audio signal input/output terminals (for both SDI 1 and
SDI 2)
Input (IN) and output (OUT) terminals for the analog audio signals.
• The IN and OUT terminals are bridge-connected.
7
Controls and Features (cont’d)
Input Card (option) (cont’d)
7 SDI Input Card (IF-C21SDG/IF-C51SDG)
The EMBEDDED AUDIO signal is acceptable. (IF-C51SDG is also equipped with an
AUDIO LEVEL METER function.)
1 SWITCHED OUT terminal
Output (OUT) terminal for the re-clocked signal. The input signal from
the input terminal currently selected (IN1 or IN2) is re-clocked and
output from this terminal.
SWITCHED
OUT
1
NOTES:
• No signal is output from the SWITCHED OUT terminal when the main power is turned
IN1
off.
2
E.AUDIO
SDI
• Even when the input signal is switched from the SDI Input Card, the SWITCHED OUT
terminal still outputs the IN1 or IN2 re-clocked signal which is selected last time.
IN2
The re-clocked signal from IN1 is output from the SWITCHED OUT terminal when the
monitor is in stand-by mode.
3
2 D1 SDI and EMBEDDED AUDIO signal input terminals
Accepts the SMPTE259M D1 SDI signal. Also accepts the
EMBEDDED AUDIO signal whose sampling frequency is 48 kHz
and the channel range is 1 to 8.
AUDIO
MONITOR
OUT
4
To select IN1: Press the INPUT SELECT C button.
To select IN2: Press the INPUT SELECT D button.
\ To select the EMBEDDED AUDIO channels and to set the AUDIO LEVEL METER
function (only for IF-C51SDG), set the DIP switches on the input card correctly. For
details, refer to the instruction manual supplied with the input card.
(This illustration is IF-C21SDG.)
7 Acceptable signal formats when installed
on this monitor:
3 Connection terminal
Attach to the connection terminal of the input card slot on the
monitor.
525/60i, 625/50i,
EMBEDDED AUDIO (8ch)
4 Audio signal output terminal
Outputs the analog audio signal after decoding the EMBEDDED
AUDIO signal.The input signal from the input terminal currently
selected (IN1 or IN2) is output from this terminal.
\ This terminal outputs the same audio signal as the audio sound output from the
speaker.
NOTES:
• No signal is output from the audio signal output terminal when the monitor is in stand-
by mode.
• Even when the input signal is switched from the SDI Input Card, this terminal still
outputs the audio signal from the IN1 or IN2 which is selected last time.
IMPORTANT
• Do not use any other input card than the input cards listed on pages 7 and 8.
Using other input cards may cause malfunction or damage the monitor. Such malfunction or damage caused by using other
input cards cannot be warranted.
• If any equipment is not connected to a bridged output (OUT) terminal, be sure not to connect any cords to the bridged output
(OUT) terminal. Connecting a cord to a bridged output (OUT) terminal will cause the terminating resistance switch to open (auto
terminate function).
• When making a bridge connection, connect the input (IN) and output (OUT) terminals on the monitor to separate video
components.
(For example, if both the input (IN) and output (OUT) terminals are connected to the same VCR, resonance may occur except
during playback. This is caused by that the same video signal circulates between the VCR and the monitor. This is not a
malfunction.)
8
Preparation
Installing the Input Card
1 Turn off the main power switch on the rear panel of the monitor and unplug the AC power
cord from the AC outlet.
2 Unscrew the screws and remove the slot cover from the input card slot on the rear panel of
the monitor.
SLOT
REMOTE
MAKE/
TRIGGER
Slot cover
3 Insert the input card’s circuit board (green-colored) into the slot, fitting the board to the
guide rails on the top and bottom of the slot.
Hold the tabs on the input card when inserting the input card.
NOTE:
Fit the board to the guide rails.
When installing IF-C21SDG/IF-C51SDG, you need to set the
DIP switches on the input card correctly to use the functions
of the input card. Refer to the instruction manual supplied with
SLOT
the input card and set the DIP switches beforehand.
REMOTE
Tab
Guide rails
Tab
Input card (This illustration is IF-C01COMG.)
4 Push in the input card so that its front panel touches the rear panel of the monitor.
5 Secure the Input Card by using the screws removed in step 2.
SLOT
REMOTE
MAKE/
TRIGGER
NOTES:
• The input card or the monitor may be damaged if you do not turn off the main power of the monitor before installing the input card.
• Do not touch the terminals or the patterns on the circuit board of the input card.
• Attach the slot cover when the input card slot is not in use.
9
Basic Menu Operations
(MENU, SET-UP MENU)
7 About the Menu Screens
This monitor features MENU which contains the functions normally used and SET-UP MENU which contains the initial settings of
the monitor.
MENU
Items
Functions
APERTURE
Adjusts the picture aperture level.
ADJ. BAR POSI.
COLOR TEMP.
COLOR SYSTEM
COMPO. LEVEL1)
RUSH DELAY
Selects the level bar position on the screen which appears when adjusting picture or volume.
Selects the color temperature.
Selects the color system.
Adjusts the component level of the monitor for the component signal or the SDI signal.
Sets the delay time between when the stand-by button is pressed and when the monitor actually turns
on.
1) Appears only when the component signal input or the SDI signal input is selected (when INPUT C or INPUT D is selected and other signals
than RGB is input).
SET-UP MENU
Items
Functions
PICTURE SUB ADJ.
The standard value (“00”) of the picture adjustment is initially set at the factory.You can adjust the
standard value as your initial setting.
CONTRAST: Adjusts contrast.
BRIGHT:
CHROMA2): Adjusts color density.
PHASE2):
Adjusts hue.
Adjusts brightness.
H. POSITION
Adjusts the horizontal position of the screen.
Adjusts the vertical position of the screen.
Adjusts the white balance.
V. POSITION
WHITE BALANCE
R. CUTOFF: Adjusts the cut-off point of the red signal.
G. CUTOFF: Adjusts the cut-off point of the green signal.
B. CUTOFF: Adjusts the cut-off point of the blue signal.
R. DRIVE:
B. DRIVE:
Adjusts the drive level of the red signal.
Adjusts the drive level of the blue signal.
CONTROL LOCK
Prohibits the monitor operations except turning on/off the monitor and adjusting volume. The menu
operations are also prohibited.
STATUS DISPLAY
REMOTE SYSTEM
INPUT REMOTE3)
Selects to display or not to display the color system of the current input on the screen.
Selects the method of the external control connected to the REMOTE terminal.
Sets how to change the input when operating the monitor by the external control.
2)
May not appear depending on the type of input signal.
Appears only when “REMOTE SYSTEM” is set to “MAKE.”
3)
10
7 Displaying the menu screens
7 Initializing the Settings
You can initialize the following settings of the monitor:
MENU, SET-UP MENU, picture adjustment, volume level
To display MENU
Press the MENU button on the front panel.
1 Press the stand-by button to turn off the
monitor (on stand-by).
To display SET-UP MENU
Press the fibutton while holding down the MENU button
on the front panel.
2 While holding down both the MENU
button and the fi button, press the stand-
by button to turn on the monitor.
• To go back to the previous menu, press the MENU button.
• To exit from the menu screen, press the MENU button
several times.
NOTE:
NOTE:
Keep pressing both the MENU button and the fi button until
“<SET-UP MENU> RESET” appears on the screen.
The menu screen will disappear if no operation has been done for
about 5 minutes.
“<SET-UP MENU> RESET” appears on the screen.
7 Menu Operation Procedure
Example:When adjusting “APERTURE” to “+10.”
1 Press the MENU button.
MENU appears on the screen.
<MENU>
APERTURE
:
00
ADJ. BAR POSI.
COLOR TEMP.
COLOR SYSTEM
COMPO. LEVEL
RUSH DELAY
: LOWER
: 9300
: AUTO
3 Press the VOLUME/SELECT (+) button to
initialize the settings.
:
00
: STD.
The settings are initialized and “<SET-UP MENU>
RESET” disappears.
EXIT
• To cancel to initialize, press the MENU button.
2 Press the %/fi button to select
“APERTURE.”
Initial settings
Functions (Items)
Initial settings
<MENU>
APERTURE
:
00
APERTURE
ADJ. BAR POSI.
COLOR TEMP
COLOR SYSTEM
COMPO. LEVEL
RUSH DELAY
PICTURE SUB ADJ.
CONTRAST
BRIGHT
CHROMA
PHASE
H. POSITION
V. POSITION
WHITE BALANCE
R. CUTOFF
00
ADJ. BAR POSI.
COLOR TEMP.
COLOR SYSTEM
COMPO. LEVEL
RUSH DELAY
: LOWER
: 9300
: AUTO
LOWER
9300
AUTO
00
:
00
MENU
: STD.
EXIT
STD.
3 Press the VOLUME/SELECT (– +)
00
00
00
00
00
00
buttons to adjust “APERTURE.”
<MENU>
APERTURE
: +10
: LOWER
: 9300
: AUTO
:
ADJ. BAR POSI.
COLOR TEMP.
COLOR SYSTEM
COMPO. LEVEL
RUSH DELAY
00
: STD.
SET-UP MENU
00
EXIT
G. CUTOFF
00
B. CUTOFF
00
R. DRIVE
B. DRIVE
00
00
4 Press the MENU button to exit from
MENU.
CONTROL LOCK
STATUS DISPLAY
REMOTE SYSTEM
INPUT REMOTE
CHROMA
OFF
ON
MAKE
A-D
00
Picture
PHASE
00
Adjustment
CONTRAST
BRIGHT
00
00
Volume
VOLUME
20
11
How to Use MENU
<MENU>
APERTURE
:
00
ADJ. BAR POSI.
COLOR TEMP.
COLOR SYSTEM
COMPO. LEVEL
RUSH DELAY
: LOWER
: 9300
: AUTO
Function display of the button varies depending on the selected item.
Buttons Displays Functions
:
00
fi
∞
5
Selects the items in forward rotation.
Selects the items in reverse rotation.
Increases the value (up to the maximum).
Selects the setting (value) in forward rotation.
Decreases the value (up to the minimum).
Selects the setting (value) in reverse rotation.
Exits from MENU.
: STD.
%
VOLUME/
SELECT(+)
VOLUME/
SELECT(–)
MENU
+
EXIT
3
–
2
EXIT
CHROMA CONTRAST
VOLUME/SELECT
MENU
PHASE
BRIGHT
7 Function, Contents, and the Adjustment Range of Each Item
APERTURE
COMPO. LEVEL
Adjusts the picture aperture level.
• 00 “ +40
Adjusts the component level of the monitor for the
component signal or the SDI signal.
• –40 “ +10
ADJ. BAR POSI.
NOTE:
When inputting the component signal or the SDI signal, check if
“COMPO. LEVEL” is adjusted properly for the standard color bar
currently used. For details, see page 5.
Selects the level bar position on the screen which
appears when adjusting picture or volume.
• UPPER
• LOWER
UPPER
VOLUME : 20
RUSH DELAY
Sets the delay time between when the stand-by button
is pressed and when the monitor actually turns on.
• STD.: Power turns on about 1 second after the
stand-by button is pressed.
• SLOW: Power turns on about 3 seconds after the
stand-by button is pressed.
VOLUME : 20
LOWER
COLORTEMP.
NOTE:
It is recommended to apply “SLOW” to some of the monitors if you
need to turn on multiple monitors at the same time.You can control
the rush current of the entire system.
Selects the color temperature.
• 9300
• 6500
COLOR SYSTEM
Selects the color system.
• AUTO: Selects NTSC or PAL automatically depending
on the input signal.
• NTSC: Keeps the NTSC color system.
• PAL: Keeps the PAL color system.
NOTE:
Normally select “AUTO.” If the input signal is unstable, select “NTSC”
or “PAL.”
12
How to Use SET-UP MENU
Function and display of the button varies depending on the selected item.
<SET-UP MENU>
Buttons Displays Functions
.
PICTURE SUB ADJ
fi
∞
5
Selects the items in forward rotation.
H. POSITION
V. POSITION
:
:
00
00
%
Selects the items in reverse rotation.
WHITE BALANCE
CONTROL LOCK
STATUS DISPLAY
REMOTE SYSTEM
INPUT REMOTE
: OFF
: ON
: MAKE
: A-D
VOLUME/
SELECT(+)
VOLUME/
SELECT(–)
MENU
+
Increases the value (up to the maximum).
Selects the setting (value) in forward rotation.
Decreases the value (up to the minimum).
Selects the setting (value) in reverse rotation.
Returns to or exits from SET-UP MENU.
3
–
EXIT
2
EXIT
When setting “WHITE BALANCE”:
Buttons Displays Functions
CHROMA CONTRAST
VOLUME/SELECT
MENU
R•B
Selects the color to adjust the drive level.
fi
R•G•B Selects the color to adjust the cut-off point.
PHASE
BRIGHT
%
DISP
Turns on/off the on screen display.
VOLUME/
SELECT(+)
VOLUME/
SELECT(–)
MENU
CUTO Adjusts the cut-off point.
+
Increases the value (up to the maximum).
DRV
–
Adjusts the drive level.
Decreases the value (up to the minimum).
Returns to SET-UP MENU.
EXIT
7 Function, Contents, and the Adjustment Range of Each Item
PICTURE SUB ADJ.
H. POSITION
The standard value (“00”) of
the picture adjustment is
initially set at the factory.You
can adjust the standard value
as your initial setting.
Adjusts the horizontal position of the screen.
NOTE:
You can adjust “H. POSITION” separately for each video input. Select
the video input you want to adjust beforehand.
<PICTURE SUB ADJ.>
CONTRAST
BRIGHT
:
:
:
:
00
00
00
00
CHROMA
PHASE
• –05 “ 00 “ +05
–: Moves the screen to the left.
+: Moves the screen to the right.
• Select “PICTURE SUB ADJ.”
on SET-UP MENU, then
press the VOLUME/SELECT
(+) button to display the
setting menu illustrated on
the right.
EXIT
V. POSITION
Adjusts the vertical position of the screen.
NOTE:
NOTES:
You can adjust “V. POSITION” separately for each video input. Select
• You can adjust the items in “PICTURE SUB ADJ.” separately for
each video input. Select the video input you want to adjust
beforehand.
the video input you want to adjust beforehand.
• –05 “ 00 “ +05
• Only “CONTRAST” and “BRIGHT” appear on the screen when the
RGB signal is input. When the signal with PAL color system is input,
“PHASE” does not appear.
–: Moves the screen downward.
+: Moves the screen upward.
7CONTRAST
• –10 “ 00 “ +10
7BRIGHT
• –10 “ 00 “ +10
7CHROMA
• –10 “ 00 “ +10
7PHASE
• –10 “ 00 “ +10
13
How to Use SET-UP MENU (cont’d)
WHITE BALANCE
CONTROL LOCK
Adjusts the white balance.
Prohibits the monitor operations except turning on/off
the monitor and adjusting volume. The menu operations
are also prohibited.
• ON: Activates this function.
• OFF: Deactivates this function.
NOTE:
You can adjust the items in “WHITE BALANCE” separately for each
color temperature (6500 or 9300). Select the color temperature you
want to adjust beforehand.
NOTES:
• When “CONTROL LOCK” is set to “ON,” “CONTROL LOCK ON!”
appears on the screen if you try to operate the monitor.
• You can deactivate this function on SET-UP MENU when
“CONTROL LOCK” is set to “ON.”
Cut-off adjustment
• Select “WHITE BALANCE”
on SET-UP MENU, then
press the VOLUME/
SELECT (+) button to
display the setting display
for the cut-off adjustment.
R. CUTOFF: 00
STATUS DISPLAY
•
•
EXIT
RGB DISP
If “COLOR SYSTEM” is set to “AUTO,” you can display
the color system (NTSC or PAL) of the current input
signal when turning on the monitor or when changing
the input.
(When “R. CUTOFF” is selected.)
7R. CUTOFF
Adjusts the cut-off point of the red signal.
• ON: Displays the color system (NTSC or PAL) of the
current input signal.
• OFF: Does not display the color system (NTSC or
PAL) of the current input signal.
• –20 “ 00 “ +20
7G. CUTOFF
Adjusts the cut-off point of the green signal.
• –20 “ 00 “ +20
NOTE:
The color system does not appear on the screen when the component
signal, RGB signal, or black-and-white signal is input.
7B. CUTOFF
Adjusts the cut-off point of the blue signal.
• –20 “ 00 “ +20
REMOTE SYSTEM
Selects the method of the external control connected to
the REMOTE terminal.
Drive level adjustment
• Select “WHITE BALANCE” on
SET-UP MENU, then press
the VOLUME/SELECT (–)
\ For details, see page 15.
• MAKE (make contact system)
• TRG. (trigger system)
button to display the setting
R. DRIVE: 00
•
display for the drive level
adjustment.
EXIT
R B DISP
INPUT REMOTE
(When “R. DRIVE” is selected.)
Sets how to change the input when operating the
monitor by the external control.
\ For details, see page 15.
7R. DRIVE
Adjusts the drive level of the red signal.
• –20 “ 00 “ +20
• A–D
• A/B
NOTE:
7B. DRIVE
Adjusts the drive level of the blue signal.
• –20 “ 00 “ +20
“INPUT REMOTE” appears on the screen only when “REMOTE
SYSTEM” is set to “MAKE.”
NOTE:
You can turn off the on screen display during the adjustment of the
white balance by pressing the % button.
14
How to Use the External Control
7 About the External Control
This monitor has the REMOTE (remote) terminal that is used for the operation by an external control.
You can select the following control methods according to the setting of “REMOTE SYSTEM” in SET-UP MENU:
• MAKE (make contact system): Controls the function by short-circuiting the corresponding pin terminal to the GND
pin terminal, or disconnecting (opening) it.
• TRG. (trigger system):
Controls the function by inputting the pulse signal instantaneously to the
corresponding pin terminal.
NOTES:
When selecting “MAKE” (the make contact system), you can select how to change the input by the external control as follows:
A–D (4-pin control): Changes the input by short-circuiting any one signal line of INPUT A to INPUT D.
A/B (1-pin control): Selects INPUT A or INPUT B by short-circuiting and opening only 2nd pin terminal. In this setting, you cannot change the
input to INPUT C or INPUT D by the external control.
• Opening:
Changes the input to INPUT A
• Short-circuiting: Changes the input to INPUT B
7 How to Use the REMOTE Terminal
No. Functions to be controlled
Opening
Short-circuiting
1
2
3
4
5
6
7
8
9
Not in use
–
–
Changes the input to INPUT A
Changes the input to INPUT B
Changes the input to INPUT C
Changes the input to INPUT D
Not in use
Invalid
Invalid
Invalid
Invalid
–
Valid
*1
*2
*2
*2
Valid
Valid
Valid
–
10
9
5
4
3
2
1
15
14
13
12
11
Not in use
–
–
8
7
6
COLOR OFF
Off
On
Not in use
–
–
10 ASPECT
Off (4:3)
Off
On (16:9)
REMOTE terminal
11 UNDER SCAN
12 Not in use
13 Not in use
14 External control
15 GND
On
–
–
–
–
Invalid
Valid
*3, 4
*1 The 2nd pin terminal works to change the input between INPUT A (opening) and INPUT B (short-circuiting) when
“INPUT REMOTE” in SET-UP MENU is set to “A/B.”
*2 These pin terminals are not in use when “INPUT REMOTE” in SET-UP MENU is set to “A/B.” Do not connect these
pin terminals in such a case.
*3 The 14th pin terminal (External control) should be controlled by the make contact system even when selecting
“TRG.” (the trigger system).
*4 Short-circuiting the 14th pin terminal (External control) enables operating other functions listed above by the
external control.
Operation
1. Short-circuit the 14th pin terminal (External control) to the 15th pin terminal (GND) so that the monitor can be
controlled by the external control.
2. When selecting “MAKE” (the make contact system), operate each function by short-circuiting the
corresponding pin terminal to the 15th pin terminal (GND) or opening it.
When selecting “TRG.” (the trigger system), operate each function by Pulse control, that is short-circuiting the
corresponding pin terminal to the 15th pin terminal (GND) for about 1 second.
NOTES:
When selecting “MAKE” (the make contact system):
• You cannot use the following buttons on the front panel:
UNDER SCAN, COLOR OFF, ASPECT, INPUT SELECT
“REMOTE ON!” appears on the screen if one of those buttons is pressed.
• When more than one terminal of INPUT A to INPUT D are selected (short-circuited), inputs are given the alphabetical priority (A, B, C, D). (We
recommend using an interlock switch which turns off a switch when another switch is turned on.)
When selecting “TRG.” (the trigger system):
• You can use the buttons on the front panel.
• You can operate only one function at a time. (We recommend using a switch which turns on only while it is pressed down.)
15
Troubleshooting
Solutions to common problems related to your monitor are described here. If none of the solutions presented here
solve the problem, unplug the monitor and consult a JVC-authorized dealer or service center for assistance.
Reference
pages
Problems
Points to be checked
Measures (Remedy)
Firmly insert the power plug.
No power supply
Is the power plug loosened or
disconnected?
—
Is the main power turned OFF?
Turn the main power switch on.
Connect the signal cable firmly.
6
No picture with the Is the signal cable disconnected?
6-8
power on
Is the power of the connected
component ON?
Turn on the power of the connected component
and set it correctly.
—
Is the signal output from the connected
component?
Is the input selected correctly?
Select the correct input with the INPUT SELECT
buttons.
5
Is the input signal adapted to the
monitor’s specification?
Check if the input signal format is acceptable to
the monitor or the input card.
6-8, 19
6-8
No sound
Is the audio cable disconnected?
Connect the audio cable firmly.
Is the audio signal output from the
connected component?
Set the connected component correctly.
—
Is the volume output set to minimum?
Adjust the volume with the VOLUME/SELECT
(– +) buttons.
4
Wrong color
Has the picture adjustment been
changed?
Set each picture adjustment to the standard
level (00). Or, set each item in “PICTURE SUB
ADJ.” in SET-UP MENU to the standard level (00).
(Or initialize the settings of the monitor.)
4, 11, 13
Has the WHITE BALANCE setting been Set each item in “WHITE BALANCE” in SET-UP
changed?
MENU to the standard level (00). Or, initialize the
settings of the monitor.
11, 14
7
Are any cables disconnected from the
component/RGB input card?
Connect each signal cable firmly.
Has the correct signal been input to the Select INPUT C when the component signal is
component/RGB input card? Has the
correct INPUT been selected on the
monitor?
input. Select INPUT D when the RGB signal is
input.
5, 7
Has the correct color system been
selected?
Set “COLOR SYSTEM” in MENU to “AUTO.”
12
Has “BLUE CHECK” or “COLOR OFF”
been activated?
Press the BLUE CHECK button or the COLOR
OFF button to deactivate the functions.
4, 5
Unnatural picture
Shaking picture
Has “CONTRAST” or “BRIGHT” been
changed?
Adjust CONTRAST or BRIGHT by using the front
panel buttons. Or, adjust “CONTRAST” or
“BRIGHT” in “PICTURE SUB ADJ.” in SET-UP
MENU.
4, 13
Is the monitor close to a motor,
transformer or any other device
generating a strong magnetic field?
(a fan, fluorescent light, laser printer,
another monitor, etc.)
Move the monitor away from the device until the
picture stops shaking.
Connect the power plug to another AC outlet away
from the former one.
—
16
Reference
pages
Problems
Points to be checked
Measures (Remedy)
Irregular color
Is the monitor placed or moved close to Move the device away from the monitor and turn
a speaker or any other device
incorporating a magnet?
off the monitor. Wait at least 30 minutes, then turn
on the monitor.
—
Has the position of the monitor been
changed with the power on?
Wrong picture
position
Has the picture position been changed? Adjust “H. POSITION” or “V. POSITION” in SET-UP
13
4, 5
14
MENU.
Has the UNDER SCAN or ASPECT
button been pressed?
When the UNDER SCAN or ASPECT button is lit,
press the button to deactivate the function.
Front panel buttons Has the CONTROL LOCK function been Set the CONTROL LOCK function to “OFF.”
do not function
set to “ON”?
Has the monitor’s setting been changed Change the setting of the external control so that
to enable control by the external control the monitor can be operated by the buttons on the
15
connected to the REMOTE terminal?
front panel.
The following are not malfunctions:
• When a bright still image (such as a white cloth) is displayed for a long period, it may appear to be colored.
This is due to the structure of the cathode ray tube and will disappear when another image is displayed.
• You may sometimes experience a mild electric shock when you touch the picture tube. This phenomenon is
due to a normal buildup of static electricity on the CRT and is not harmful.
• The monitor emits a strange sound when the room temperature changes suddenly. This is only a problem if an
abnormality appears on the screen as well.
• If two or more monitors are placed close each other, their images may shake or be distorted. This phenomenon
is due to mutual interference; it is not a malfunction. Move the monitors away from each other until the
interference disappears or turn the power off on any monitor that is not being used.
17
Specifications
MODEL
TM-H150CG
Type
Color video monitor
PAL, NTSC (3.58)
Color system
39 cm (15") measured diagonally,
90° deflection, in-line gun,
trio-dot type
Picture tube
(phosphor dot-trio pitch 0.27 mm)
Width:
Height:
285.5 mm (11 3/16")
214 mm (8 3/8")
Effective screen size
Scanning frequency
Horizontal resolution
Input terminals
Diagonal: 356 mm (14")
H: 15.734 kHz (NTSC), 15.625 kHz (PAL)
V: 59.94 Hz (NTSC), 50 Hz (PAL)
750 TV lines or more
(Y/C input mode)
VIDEO A
VIDEO B
Composite video: 1 line, BNC connector x 2,
1 V(p-p), 75 Ω, negative sync
(bridge connection possible, auto termination)
Composite video: 1 line, BNC connector x 2,
1 V(p-p), 75 Ω, negative sync
(bridge connection possible, auto termination)
Y/C-separated: 1 line, mini-DIN 4-pin connector x 2
Y: 1 V (p-p), 75 Ω
C (BURST): 0.286 V (p-p), 75 Ω (NTSC) 0.3 V (p-p), 75 Ω (PAL)
(bridge connection possible, auto termination)
AUDIO A
AUDIO B
REMOTE
1 line (monaural), RCA pin x 2, 0.5 V(rms), high-impedance
(bridge connection possible)
1 line (monaural), RCA pin x 2, 0.5 V(rms), high-impedance
(bridge connection possible)
Point-of-contact connection, 1 line D-sub connector (15-pin, 3-line)
Audio power output
Built-in speaker
1 W
8 cm round x 1, impedance of 8 Ω
Environmental conditions
Operation temperature: 5°C – 40°C (41°F – 104°F)
Operation humidity: 20 % – 80 % (non-condensing)
Power requirements
Power consumption
120 V/220 – 240 V AC, 50 Hz/ 60 Hz
1.2 A (120 V AC)/0.8 A (220 – 240 V AC)
Width:
Height:
Depth:
360 mm (14 1/4")
310 mm (12 1/4")
418 mm (16 1/2")
Dimensions
Weight
16 kg (35.2 lbs)
(not including input card)
Accessory
AC power cord
• Illustrations used in this manual are for explanatory purposes only. The appearance of the actual product may differ slightly.
• Dimensions and weight are approximate.
• E. & O. E. Design and specifications subject to change without notice.
18
7 Dimensions
Unit : mm (inch)
• Asterisks (*) are used to indicate the screen dimensions.
1
1
418 (16
407 (16
/
2
)
)
Front
Side
1.5
( /16)
/
8
1
/4)
360 (14
1
3
/4)*
295.5 (11
308
1
60.2
3
/8)
3
238 (9
/8)
(12
/
4)
(2
20
7
/8)
(
7 Acceptable Signal Formats
‡: Acceptable
–: Not acceptable
When an input card (not supplied) is installed
Terminals on the
rear of the monitor
Input Signals
NTSC (3.58 MHz)
PAL
IF-C01COMG
IF-C01SDG
IF-C21SDG
IF-C51SDG
–
–
–
–
–
–
–
–
‡
‡
Black-and-White
(50 Hz/60 Hz)
–
–
–
–
‡
480/60i (525i)
576/50i (625i)
‡
‡
‡
‡
‡
‡
‡
‡
–
–
EMBEDDED
AUDIO
–
–
‡
‡
–
Analog audio
‡
‡
–
–
‡
\ For details about each input card, see pages 7 and 8.
7 Y/C (Mini DIN 4 pin) terminals
2
4
Pin No.
Signal
GND (Y)
GND (C)
Y
1
2
3
4
1
2
3
4
C
3
1
19
VICTOR COMPANY OF JAPAN, LIMITED
Printed in Thailand
0204MKH-MW-MT
2004 VICTOR COMPANY OF JAPAN, LIMITED
©
|