JVC Interi Art LCT0622 001A U User Manual

COLOUR TELEVISION

AV-28WFT1EI

CONTENTS

SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . 2

PREPARATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

T-V LINK FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . 7

BASIC OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . 8

REMOTE CONTROL BUTTONS AND FUNCTIONS . 11

MENU OPERATION . . . . . . . . . . . . . . . . . . . . . . . . 16

PICTURE SETTING. . . . . . . . . . . . . . . . . . . . . . . . . 17

PICTURE FEATURES. . . . . . . . . . . . . . . . . . . . . . . 18

SOUND SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . 20

EXT SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

INSTALL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

DEMO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

ADDITIONAL MENU OPERATIONS . . . . . . . . . . . . 30

ADDITIONAL PREPARATION. . . . . . . . . . . . . . . . . 32

TV BUTTONS AND PARTS. . . . . . . . . . . . . . . . . . . 34

TROUBLESHOOTING. . . . . . . . . . . . . . . . . . . . . . . 35

SPECIFICATIONS. . . . . . . . . . . . . . . . . . . Back cover

INSTRUCTIONS

Thank you for buying this

colour television.

To make sure your fully understand how to use your new TV, please read this manual thoroughly before you begin.

6$)(7<#35(&$87,216

■ :DUQLQJ

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EX-

POSE THIS APPLIANCE TO RAIN OR MOISTURE.

■

&DXWLRQ

TO ENSURE PERSONAL SAFETY, OBSERVE THE FOL-

LOWING RULES REGARDING THE USE OF THIS UNIT.

1 Operate only from the power source specified (AC 220 –

240 V, 50 Hz) on the unit.

2 Avoid damaging the AC plug and power cord.

3 Avoid improper installation and never position the unit

where good ventilation is unattainable.

When installing this television, distance recommendations

must be maintained between the floor and wall, as well as

instalment in a tightly enclosed area or piece of furniture.

Please adhere to the minimum distance guidelines shown

for safe operation.

15 cm

10 cm

15 cm

4 Do not allow objects or liquid into the cabinet openings.

5 In the event of a fault, unplug the unit and call a service

technician. Do not attempt to repair it yourself or remove

the rear cover.

6 When you don’t use this TV set for a long period of time, be

sure to disconnect the power plug from the AC outlet.

7 Do not hold the front panel door when moving the TV, if you

do you may break it.

How To Replace The Fuse

Open the fuse compartment

with a blade screwdriver, and

replace the fuse.

Fuse

■

*XLGHOLQHV#IRU#6DIH#2SHUDWLRQ

This equipment has been designed and manufactured to comply with international safety standards. However, as with any elec-

trical appliance, care must be taken to ensure optimal results and operational safety.

• Before attempting to use this equipment, read the operating instructions thoroughly.

• Ensure that all electrical connections (including the mains plug, extension leads, etc.) have been made in accordance with the

manufacturer’s instructions.

• If ever in doubt about the installation, operation or safety of this equipment, consult your dealer.

• Handle all glass panels or covers with care.

• Never operate this equipment if it appears damaged or operates abnormally. Turn the power off, disconnect the main power

plug and consult your dealer.

• Never remove any affixed panels or covers. Doing so may result in electrical shock.

• Never leave this equipment operating unattended unless otherwise specifically stated that it is designed to do so or in standby

mode. Only use the designated power switch to turn off the power and ensure that all potential users are instructed how to do

so. Make special arrangements for infirm or handicapped persons.

• Never watch TV while operating a motor vehicle. It is illegal to watch TV while driving.

• Never listen to headphones at high volume. Doing so may damage your hearing.

• Never obstruct the ventilation of this equipment. Doing so may cause overheating and result in a malfunction or damage.

• Never use makeshift stands or attempt to affix legs with wood screws. When using a manufacturer’s approved stand or legs,

use only the fixtures provided and follow the installation instructions.

• Never allow this equipment to be exposed to rain or moisture.

• Never allow anyone, especially children, to insert anything into an opening in the case. Doing so may result in a fatal electrical

shock.

• Never guess or take chances with electrical equipment of any kind. It is better to be safe than sorry.

35(3$5$7,21

■ &RQQHFWLQJ#WKH#$HULDO#DQG#9&5

→

If connecting a VCR, follow A

If not connecting a VCR, follow 1

2 .

D .

AC Outlet

(AC 220 - 240 V,

50 Hz)

→

*1: To operate T-V LINK functions, a T-V LINK compatible

VCR must be connected to the EXT-2 terminal on the TV.

For details about T-V LINK functions, see “T-V LINK

FUNCTIONS” on page 7.

VHF/UHF Aerial

Note:

• For further details, refer to the manuals provided with the

devices to be connected.

Power

Cord

• The connecting cables are not provided.

75-ohm

Coaxial

Cable

• A video can be viewed from the VCR without performing

C . For details, refer to your VCR instruction manual.

EXT-2

EXT-3

• To connect additional external devices, please see “AD-

DITIONAL PREPARATION” on page 32.

EXT-1

AUDIO OUT

• To connect external speakers and audio system, please

see “Connecting Speakers/Amplifier” on page 33.

Aerial

Plug

• When a decoder is connected to a T-V LINK compatible

VCR, set the DECODER (EXT-2) function to ON. For de-

tails, see “Using the DECODER (EXT-2) function” on

page 30. Otherwise, you will not be able to view scram-

bled channels.

21-pin SCART Cable

Aerial Plug

75-ohm Coaxial

Cable

VCR

To Aerial

Input

Aerial Plug

To Aerial

Output

AV IN/OUT

Terminal

■ 3XWWLQJ#%DWWHULHV#LQWR#WKH#5HPRWH#&RQWURO

Use two AAA/R03 dry cell batteries.

Insert the batteries from the ó end, making sure the ô and ó

polarities are correct.

To open the battery compartment, slide the door downwards

and lift off. Replace the door by sliding it upwards until it is se-

cure.

Note:

• Follow the warnings printed on the batteries.

• Battery life is about six months to one year, depending on

your frequency of use.

• If the remote control does not work properly, replace the

batteries.

• The batteries we supply are only for setting up and test-

ing your TV, please replace them as soon as necessary.

• Always use good quality batteries.

PREPARATION

■ ,QLWLDO#6HWWLQJV

When the TV is first turned on, it enters the initial setting

mode, and the JVC logo is displayed. Follow the instructions

on the on-screen display to make the initial settings.

Press the Main power button on the TV.

The Power lamp lights red (for power on), then green (for

TV on) and the JVC logo is displayed.

Note:

• If the power lamp stays red and does not change to

green:

Main power button

Your TV is in the standby mode. Press the

(Standby) button on the remote control to turn your

TV on.

Power lamp

• The JVC logo does not appear when your TV has

been turned on once.

In this case, use the “LANGUAGE” and “AUTO PRO-

GRAM” functions to make the initial settings. For de-

tails, see “INSTALL” on page 25.

2 Press the

button.

The LANGUAGE menu appears.

3 Press the ë buttons to choose ENG-

LISH.

English is set for the on-screen display description.

RM-C51

PREPARATION

4 Press the

button to start the AUTO

PROGRAM function.

Note:

• When you TV can detect the TV channel name from

the TV channel broadcast signal, it automatically

registers the TV channel name (ID) to the Pro-

gramme number (PR) in which the TV channel has

been registered.

The AUTO PROGRAM menu appears and received TV

channels are automatically registered in the Programme

numbers (PR).

• If a TV channel you want to view is not set to a Pro-

gramme number (PR), manually set it using the

MANUAL function. For details, see “EDIT/MANUAL”

on page 26.

• The TV channel is not registered in Programme

number PR 0 (AV). When you want to register a TV

channel to PR 0 (AV), manually set it using the MAN-

UAL function. For details, see “EDIT/MANUAL” on

page 26.

To cancel the AUTO PROGRAM function:

Press the

button.

5 After the TV channels have been regis-

tered in the Programme numbers (PR),

the EDIT menu appears.

You can proceed to edit the Programme numbers (PR)

using the EDIT/MANUAL function. For details, see “ED-

IT/MANUAL” on page 26.

When not using the EDIT/MANUAL function:

If you do not need to use the EDIT/MANUAL function,

go to the next step.

6 Press the

button to display the T-V

LINK menu.

7 Operate the T-V LINK menu according

to the type of a VCR connected to the

EXT-2 terminal.

When a T-V LINK compatible VCR is not con-

nected:

Press the

The T-V LINK menu disappears.

button to exit the T-V LINK menu.

When a T-V LINK compatible VCR is connected:

Follow the operating procedure “Downloading the data

to VCR” on page 30 to transmit the Programme number

(PR) data.

8 Now, the initial settings are complete,

and you can watch the TV.

709#/,1.#)81&7,216

When a T-V LINK compatible VCR is connected to the EXT-

2 Terminal on the TV, it is easier to set up the VCR and to

Note:

view videos. T-V LINK uses the following features:

• Operation via the TV is not possible.

• Generally, the VCR cannot record a TV channel that can-

not be received properly by the VCR’s tuner, even though

you can view that TV channel on the TV. However, some

VCRs can record a TV channel by using the TV’s output

if that channel can be viewed on the TV, even though the

TV channel cannot be received properly by the VCR’s

tuner. For details, refer to your VCR instruction manual.

To use T-V LINK functions:

A T-V LINK compatible VCR is necessary.

The VCR must be connected to the EXT-2 terminal on the TV

by a fully wired SCART cable.

Note:

• A “T-V LINK compatible VCR” means a JVC VCR with the

T-V LINK logo or a VCR with one of the following logos.

However, these VCRs may support some or all of the fea-

tures described below. For details, refer to your VCR in-

struction manual.

■ 79#$XWR#3RZHU#2Q29&5#

,PDJH#9LHZ

“Q-LINK” (a trademark of Panasonic Corporation)

“Data Logic” (a trademark of Metz Corporation)

“Easy Link” (a trademark of Phillips Corporation)

“Megalogic” (a trademark of Grundig Corporation)

“SMARTLINK” (a trademark of Sony Corporation)

When the VCR starts playing, the TV automatically turns on

and the images from EXT-2 terminal are displayed on the

screen.

When the VCR menu is operated, the TV automatically turns

on and the images from EXT-2 terminal are displayed on the

screen.

■ 3UH0VHW#'RZQORDG

Note:

• This function does not operate if your TV’s main power is

turned off. Set your TV’s main power to on (standby

mode).

Download the registered data on the TV channels from the TV

to the VCR.

The Preset Download function automatically begins when the

initial setting is complete or whenever the AUTO PROGRAM

or EDIT/MANUAL operations are performed.

Note:

• This function can be operated via VCR operation.

When “FEATURE NOT AVAILABLE” is displayed:

If “FEATURE NOT AVAILABLE” is displayed, the download

was not performed correctly. Before trying to download again,

ensure the following:

• The VCR power is turned on.

• The VCR is T-V LINK compatible.

• The VCR is connected to the EXT-2 terminal.

• The SCART cable is fully wired.

■ 'LUHFW#5HF

“What You See Is What You Record”

You can record to VCR the images that you are currently

viewing on TV by a simple operation.

For details, read the manual for your VCR.

Operate via the VCR. “VCR IS RECORDING” is displayed.

In the following conditions, the VCR will stop recording if

the TV is turned off, if the TV channel or input is switched,

or if the menu is displayed on the TV:

• When recording images from an external device connected

to the TV.

• When recording a TV channel after it has been unscrambled

on a decoder.

• When recording a TV channel by using the TV’s output be-

cause that TV channel cannot be properly received on the

VCR’s tuner.

%$6,&#23(5$7,21

■ 7XUQ#WKH#0DLQ#SRZHU#RQ

Press the Main power button on the TV.

The Power lamp lights red and your TV is in the standby mode.

Note:

• If the Power lamp lights green, the TV is already on.

To turn the Main power off:

Press the Main power button again.

The Power lamp goes off.

Note:

• To save energy, turn the main power off if you are not us-

ing the TV for a long period of time.

Main power button

Power lamp

■ 7XUQ#WKH#79#RQ#IURP#VWDQGE\#PRGH

Press the

button, the

buttons.

(Standby) button, the

buttons or the Number

The Power lamp lights red to green and your TV will be turned on.

To turn the TV off:

Number

buttons

Press the

(standby) button again.

The Power lamp changes from green to red and the TV enters

standby mode.

■ &KRRVH#D#79#FKDQQHO

Choose a Programme number (PR) in which the desired Pro-

gramme TV channel has been set.

Use the ë buttons:

Press the ë buttons to choose the desired Pro-

gramme number (PR).

Use the Number buttons:

Enter the desired Programme number (PR) with the

Number buttons.

Example

→

• PR12

press ~ and Ÿ .

• PR6 → press ¤ .

Use the PR LIST:

1 Press the 9 (Information) button to

RM-C51

display the PR LIST.

;

BASIC OPERATION

Use the ë buttons:

Press the ë buttons to choose an EXT terminal

2 Press the ì and ë buttons to choose a

Programme number (PR). Then press the

button.

Use the PR LIST:

1 Press the

(Information) button to

Note:

display the PR LIST.

• For Programme numbers (PR) with the CHILD

LOCK function set, the (CHILD LOCK) mark is

displayed next to the Programme number (PR) in

the PR LIST

2 Press the

and

buttons to choose an

EXT terminal. Then press the

button

• You cannot use the ë buttons to choose a Pro-

gramme number (PR) with the CHILD LOCK fun-

tion set.

Note:

• The EXT terminals are registered after the Pro-

gramme number PR 99.

• Even if you try to choose a Programme number

• You can choose a video input signal from the S-VID-

EO signal (Y/C signal) and regular video signal

(composite signal). For details, see “K(S-VIDEO

input)” on page 21.

(PR) with the CHILD LOCK function set, the

(CHILD LOCK) mark will appear, and you cannot

watch the TV channel. To watch the TV channel,

see “CHILD LOCK” on page 23.

• If you do not have a clear picture or no colour ap-

pears, change the colour system manually. See

“COLOUR SYSTEM” on page 18.

• If the picture is tilted, correct it. See “PICTURE

TILT” on page 19.

•

When choosing an EXT terminal with no input signal,

the EXT terminal number becomes fixed on the screen.

■ $GMXVW#WKH#YROXPH

• This TV set has a function which can automatically

change over the input according to a special signal

output from an external device.(The EXT-4 terminal

does not support it.)

Press the

ume.

buttons to adjust the vol-

The Volume indicator appears and the volume changes as

you press the C buttons.

To return to a TV channel:

buttons or the Number but-

^{Press the}4 ^{button, the}

tons.

■ :DWFK#LPDJHV#IURP#H[WHUQDO#

To use the Programme number PR 0 (AV):

When the TV and VCR are connected only by the Aerial

cable, choosing the Programme number PR 0 (AV) al-

lows you to view images from the VCR. Set the VCR RF

channel to the Programme number PR 0 (AV) manually.

For details, see “EDIT/MANUAL” on page 26.

GHYLFHV

Choose an EXT terminal to which the desired external device

has been connected.

Use the

button:

Pressing the

button changes the choice as follows:

Press the

button to choose an EXT terminal.

Pressing the

button changes the choice as follows:

TV mode

PR 0

EXT modes

EXT-1

EXT-2

EXT-3

TV mode

EXT modes

Programme

numbers

Programme

numbers

PR 1 – PR 99

EXT-1

EXT-4

EXT-2

EXT-3

EXT-4

Note:

• The VCR RF channel is sent as the RF signal from

the VCR.

• Also refer to your VCR instruction manual.

BASIC OPERATION

■ 2SHUDWLQJ#ZLWK#WKH#EXWWRQV#RQ#WKH#79

1 ^{Press the P B buttons to turn the}

TV on from standby mode.

Press the P

buttons to choose a

Programme number (PR) or an EXT ter-

minal.

(Behind the front cover)

3 ^{Press the}D (Volume) button and the

C buttons to adjust the volume.

1 Press the D (Volume) button.

The volume level indicator appears.

2 Press the C buttons while the volume lev-

el indicator is displayed.

5(027(#&21752/#%877216#$1'#)81&7,216

1 0XWLQJ#%XWWRQ

You can turn the sound off instantly.

Press the

sound. Pressing the

restores the previous Volume level.

(Muting) button to turn off the

(Muting) button again

2 1XPEHU#%XWWRQV

You can choose a Programme number (PR) by

entering the Programme number.

Example:

→

• PR12

press ~ and Ÿ .

→

• PR6

press ¤ .

You can also press the

EXT terminal.

button repeatedly to choose an

3 =220#%XWWRQ

You can change the screen size according to the picture as-

pect ratio. Choose the optimum one from the following ZOOM

modes.

AUTO:

For any picture format except Normal Picture (4:3 Aspect Ra-

tio), the picture will be automatically displayed in the optimum

screen size.

For Normal Picture (4:3 Aspect Ratio), the picture is displayed

in accordance with the ZOOM mode set in the 4:3 AUTO AS-

PECT menu. For details, see “4:3 AUTO ASPECT” on

page 18.

Note:

• AUTO may not function properly with poor signal quality.

In this case, choose an optimum ZOOM mode manually.

• This TV supports WSS (wide-screen signals). When

broadcasts with WSS are received with the ZOOM mode

set at AUTO, the most suitable ZOOM mode is automati-

cally chosen according to the WSS received.

RM-C51

• With the ZOOM mode set to AUTO, if the special signal

from an external device such as a VCR or DVD etc. is re-

ceived the ZOOM mode automatically changes to 16:9

ZOOM. (Except if the external source is connected to

EXT-4.)

How to open the cover

REGULAR:

Use to view a normal picture (4:3 aspect ratio) in its original

shape.

REMOTE CONTROL BUTTONS AND FUNCTIONS

PANORAMIC:

This mode stretches the left and right sides of a normal pic-

ture (4:3 Aspect Ratio) to fill the screen, without making the

picture appear unnatural.

2 Press the

buttons to choose a ZOOM

button.

mode. Then press the

The picture expands and the chosen ZOOM mode is dis-

played in about 5 seconds.

Note:

• You can pre-set a ZOOM mode for the normal pic-

ture. See “4:3 AUTO ASPECT” on page 18.

Note:

$GMXVWLQJ#WKH#YLVLEOH#DUHD#RI#WKH#SLF0

• The top and bottom of the picture are slightly cut off.

WXUH

If subtitles or the top (or bottom) of the picture are cut off, ad-

just the visible area of the picture manually.

14:9 ZOOM:

This mode zooms up the Wide Picture (14:9 Aspect Ratio) to

the upper and lower limits of the screen.

1 Press the

button.

The ZOOM menu appears.

2 Press the

button to display the ZOOM

mode indication.

Indicator is displayed.

16:9 ZOOM:

This mode zooms up the Wide Picture (16:9 Aspect Ratio) to

the full screen.

3 While it is displayed, press the

buttons

to adjust the visible area vertically.

16:9 ZOOM SUBTITLE:

This mode zooms up the Wide Picture (16:9 Aspect Ratio)

with subtitles to the full screen.

Note:

• You cannot adjust the visible area in REGULAR or

FULL mode.

4 +<3(5#6281'#%XWWRQ

You can enjoy sounds with a wider ambience.

Press the

the HYPER SOUND function on or off.

(HYPER SOUND) button to turn

FULL:

This mode uniformly stretches the left and right sides of a nor-

mal picture (4:3 aspect ratio) to fill the wide TV screen.

Note:

• For 16:9 aspect ratio pictures that have been squeezed

into a normal picture (4:3 aspect ratio), use the FULL

mode to restore the picrure to its original shape.

Note:

• The HYPER SOUND function does not work properly with

&KRRVH#WKH#=220#PRGH

1 Press the 5 button to display the ZOOM

mono sound.

• The HYPER SOUND lamp lights while the HYPER SOUND

function is in use.

menu.

• The HYPER SOUND function can be also turned on or off

by using the SOUND SETTING menu. For details, see

“HYPER SOUND” on page 20.

REMOTE CONTROL BUTTONS AND FUNCTIONS

5 #,QIRUPDWLRQ#%XWWRQ

You can display the PR LIST or the Current Time on the

screen.

8 6WDQGE\#%XWWRQ

Press the

on or off.

(Standby) button to turn the TV

Press the

Pressing the

play as follows:

(Information) button.

(Information) button changes the dis-

When the TV is turned on, the power lamp changes from red

to green.

9 &RORXU#%XWWRQV

The colour buttons are used for the teletext operations or the

menu operations. For details, see “~ Teletext Control But-

tons and VCR/(/DVD Switch” on page 14 or “MENU OPER-

ATION” on page 16.

0 2.#%XWWRQ

The

button is used to operate menus. For details, see

“MENU OPERATION” on page 16.

#%XWWRQV

You can choose a Programme number (PR) or an EXT termi-

nal.

Current time

No indication

Press the

buttons to choose an Pro-

gramme number (PR) or an EXT terminal.

The

buttons are also used to operate menus.

Note:

For details, see “MENU OPERATION” on page 16.

• You can choose Programme numbers (PR) or EXT termi-

nals with the PR LIST. For details, see “Use the PR LIST:”

on page 8.

= 9&52'9'# &RQWURO# %XWWRQV# DQG

9&52(2'9'#6ZLWFK

• This TV uses teletext data to set the current time. If the TV

has not received a TV channel that has teletext pro-

grammes since it was turned on, the time display is blank.

To view the current time, choose a TV channel that has

teletext programmes. The time will still be displayed as

long as you do not turn off the TV, even if you choose oth-

er TV channels.

These buttons can be used to operate a JVC brand VCR or

DVD player. Pressing a button which has the same appear-

ance as a button on the original remote control of the VCR or

DVD player makes the function work in the same way as the

button on the original remote control.

• When watching videos, an incorrect current time is some-

1 Set the VCR/(/DVD Switch to the VCR or

times displayed.

DVD position.

VCR:

• The

(Information) button is also used to operate

menus. For details, see “MENU OPERATION” on

When you are operating the VCR, set the switch to the

VCR position.

page 16.

DVD:

6 79#%XWWRQ

You can return to a TV channel instantly.

When you are operating the DVD player, set the switch

to the DVD position.

Press the

button.

(Text):

(

The TV returns to the TV mode and a TV channel appears.

When you are viewing Teletext programmes, set the

switch to the (Text) position.

(

Note:

• The

button is also used to operate menus. For details,

see “MENU OPERATION” on page 16.

2 Press the VCR/DVD Control Button to con-

trol your VCR or DVD player.

7 ì#%XWWRQV

You can adjust the volume.

Note:

• If your device is not made by JVC, these buttons

cannot be used.

• Even if your device is made by JVC one or more of

these buttons may not work, dependent on the de-

vice you are using.

Press the ì buttons to adjust the sound.

Note:

• You can use the

buttons to choose a TV channel

• The ì buttons are also used to operate menus. For de-

tails, see “MENU OPERATION” on page 16.

the VCR will receive or choose the chapter the DVD

player plays back.

• Some models of DVD player use the

buttons for

operation of both the Fast forward/backward func-

tions and for choosing the chapter. In this case, the

1/¡ buttons do not work.

REMOTE CONTROL BUTTONS AND FUNCTIONS

■ ~ #7HOHWH[W#&RQWURO#%XWWRQV#DQG#9&52(2'9'#6ZLWFK

3 Press and hold down

button.

%DVLF#RSHUDWLRQ

You can view two types of teletext broadcasts on the TV:

FLOF (Fastext) and WST (World Standard Text).

The four page numbers blink white to indicate that they

are stored in memory.

1 Choose a TV channel with a teletext broad-

cast.

To call up a stored page:

1 Press the ù button to engage the List

2 Set the VCR/(/DVD switch to the

(Text)

mode.

(

position.

2 Press a colour button to which a page has

been assigned.

3 Press : (Text) button to display the

To exit the List mode:

Press the ù button again.

teletext.

Pressing : (Text) button changes the mode as fol-

lows:

+ROG

You can hold a teletext page on the screen for as long as you

want, even while several other teletext pages are being re-

ceived.

Press the û button.

TV mode

Text mode

Hold indication

4 Choose a teletext page by pressing the

buttons, Number buttons or Colour

buttons.

To cancel the Hold function:

To return to the TV mode:

Press û button again.

Press the

button or

(Text) button.

6XE0SDJH

Note:

Some teletext pages include sub-pages that are automatically

displayed.

• If you have trouble receiving teletext broadcasts,

consult your local dealer or the teletext station,

You can hold any sub-page, or view it at any time.

• In the Text mode, the ZOOM mode is fixed to the

FULL mode.

1 Press the õ button to operate the Sub-

• No menu operations are possible when viewing a

teletext programme.

page function.

2 Press the Number buttons to enter a sub-

page number.

8VLQJ#WKH#/LVW#0RGH

You can store the numbers of your favourite teletext pages in

memory and call them up quickly using the colour buttons.

Example:

• 3rd sub-page → press ) , ) , ) and 3 .

To store the page numbers:

To cancel the Sub-page function:

^{Press the}õ ^{button again.}

1 Press

button to engage the List mode.

The stored page numbers are displayed at the bottom of

the screen.

Note:

• You can also choose a sub-page by pressing the

red or green button.

2 Press a Colour button to choose a posi-

tion. Then press the Number buttons to en-

ter the page number.

REMOTE CONTROL BUTTONS AND FUNCTIONS

5HYHDO

Some teletext pages include hidden text (such as answers to

a quiz).

You can display the hidden text.

Each time you press the ø button, text is hid-

den or revealed.

6L]H

You can double the height of the teletext display.

Press the ÷ button.

,QGH[

You can return to the index page instantly.

^Pressú ^button.

FLOF (Fastext)/WST (World Standard Text):

Returns to page 100 or a previously specified page.

List mode:

Returns to the page number displayed in the lower left area of

the screen.

&DQFHO

You can search for a teletext page while watching TV.

1 Press the Number button to enter a page

number, or press a Colour button.

The TV searches for a teletext page.

2 ^Pressü ^button.

The TV programme appears. When the TV finds the

teletext page, its page number appears in the upper left

of the screen.

3 ^Pressü ^{button to return to a teletext}

page when the page number is on the

screen.

Note:

• The TV mode cannot be resumed by pressing the

button. The TV programmes are temporarily dis-

played instead of the teletext programme. To return

to TV mode press the

button.

0(18#23(5$7,21

This TV has a number of functions you can operate using

menus. To fully utilize all your TV’s functions, you need to un-

derstand the basic menu operating techniques fully.

1 Press the

button to display the

MENU (main menu).

The MENU (main menu) appears. In it, the titles of the

menus are displayed.

2 ^{Press the}

buttons to choose a

^{menu title, and press the}3 ^button.

The menu appears.

3 ^{Operate the menus according to the}

operation description of each function.

Note:

• For details, refer to the operation descriptions of

each function described for each menu which fol-

lows this “MENU OPERATION”.

• The display appearing at the bottom of a menu indi-

cates a button on the remote controller you can use

when you operate a chosen function.

4 ^Press

button to complete the set-

ting.

The menu disappears.

To return to the previous menu:

Press

(information) button.

To exit a menu instantly:

^{Press the}4 ^button.

3,&785(#6(77,1*

Note:

• You can change the HUE setting (picture hue) only

when the colour system is NTSC 3.58 or NTSC 4.43.

To return to the default settings in each TINT

mode:

Press the blue button.

Returns the picture settings in the currently chosen TINT

mode to the default settings, and stores them in the TINT

mode again.

To display the PICTURE SETTING menu:

1 Press the

button to display MENU

(main menu).

2 Press the ë button to choose PICTURE

SETTING, and press the button.

3 Press the

tings.

button to complete the set-

The menu disappears.

■ 7,17

■ (&2#02'(

When you set the ECO MODE function to ON, the screen

contrast is automatically adjusted to a setting suitable for the

brightness of your room. This reduces eye strain for you and

the power consumption of the TV.

You can select one of three TINT modes (three kinds of pic-

ture settings) to adjust the picture settings automatically.

1 Press the ë buttons to choose TINT.

2 Press ì buttons to choose a mode.

1 Press ë buttons to choose ECO MODE.

COOL:

2 Press ì buttons to choose ON.

A cool white colour base with a boost in the colour and

contrast levels that creates a more vivid picture.

To cancel the ECO MODE function:

Press ì buttons to choose OFF.

WARM:

A warm orange/red colour base that creates the appro-

priate colour and contrast levels for watching films.

3 Press the

ting.

button to complete the set-

NORMAL:

The menu disappears.

A normal white colour base with normal colour and con-

trast levels.

Note:

• If you set the ECO MODE function to ON, the ECO lamp

lights.

3 Press the

ting.

button to complete the set-

The menu disappears.

■ 3LFWXUH#$GMXVWPHQW

You can change the picture settings of each TINT mode as

you like.

The picture settings changed are stored in the TINT mode.

1 Press the ë buttons to choose an item.

2 Press the ì buttons to change the set-

ting.

Item

Lower

Higher

CONTRAST

(picture contrast)

Darker

Softer

Brighter

Sharper

Deeper

BRIGHT

(picture brightness)

SHARP

(picture sharpness)

Lighter

Reddish

COLOUR

(picture colour)

Greenish

HUE

(picture hue)

3,&785(#)($785(6

2 Press the ì buttons to choose the ap-

propriate colour system.

PAL:

PAL system

NTSC 3.58:

NTSC 3.58 MHz system

NTSC 4.43

NTSC 4.43 MHz system

AUTO:

To display the PICTURE FEATURES menu:

This function detects a colour system from the input sig-

nal. Only when you are viewing a picture from Pro-

gramme number PR 0 (AV), or EXT terminal, you can

choose using the AUTO function.

1 Press the

button to display MENU

(main menu).

2 Press the ë button to choose PICTURE

FEATURES, and press the button.

3 Press the

ting.

button to complete the set-

■ $872#915

The AUTO VNR function optimally reduces noise of the TV

automatically according to the noise of the current picture.

The function also adjusts the optimum Sharpness (SHARP).

The menu disappears.

Note:

• The AUTO function may not function properly if you

have poor signal quality. If the picture is abnormal in

the AUTO function, choose another colour system

manually.

1 Press the ë buttons to choose AUTO

VNR.

• When in the Programme numbers PR 0 (AV) to PR

99, you cannot choose NTSC 3.58 or NTSC 4.43.

2 Press the ì buttons to choose AUTO.

MIN:

The AUTO VNR function is cancelled. When you set the

mode to AUTO but feel that the sharpness of the original

picture has not be reproduced fully, change the mode to

MIN. However, a noise remaining in the original picture

may be emphasized.

■ 7=6#$872#$63(&7

You can choose one of three ZOOM modes, REGULAR,

PANORAMIC or 14:9 ZOOM, as the ZOOM mode for the nor-

mal picture (4:3 aspect ratio).

MAX:

This mode always maximizes the noise reduction effect

irrespective of state of the picture. When you set the

mode to AUTO but feel that the noise is remarkable,

change the mode to MAX. However, this may reduce the

sharpness of the picture.

1 Press the

buttons to choose 4:3 AUTO

button.

ASPECT. Then press the

The Sub-menu of the 4:3 AUTO ASPECT function ap-

pears.

3 Press the

ting.

button to complete the set-

The menu disappears.

■ &2/285#6<67(0

The colour system is chosen automatically. However, if the

picture is not clear or no colour appears, choose the colour

system manually.

2 Press the

mode.

buttons to choose a ZOOM

1 Press the

buttons to choose COLOUR

button.

3 Press the

tings.

button to complete the set-

SYSTEM. Then press the

The Sub-menu of the COLOUR SYSTEM function ap-

pears.

The menu disappears.

PICTURE FEATURES

■ 3,&785(#7,/7

There are cases where the Earth’s magnetic force may make

the picture tilt. If this happens, you can correct the picture tilt.

1 Press the

buttons to choose PICTURE

button.

TILT. Then press the

The Sub-menu of the PICTURE TILT function appears.

2 Press the

comes level.

buttons until the picture be-

3 Press the

ting.

button to complete the set-

The menu disappears.

6281'#6(77,1*

■ 63($.(5

You can turn off the sound from the TV speakers; but you

should only do this if an audio system is connected to the TV

as a substitute for the TV speakers. When you are using this

function, see “Setting the SPEAKER function” on page 31.

When a sound is not issued from the TV speaker:

If the SPEAKER function is set to OFF, the TV speaker does

not issue sound. Press the ë buttons to choose the

SPEAKER. Then press ì buttons to choose ON.

To display the SOUND SETTING menu:

1 Press the

button to display MENU

(main menu).

■ %%(

2 Press the

button to choose SOUND

You can use the BBE function to enjoy easy-to-listen sound

that is faithful to the original sound recorded.

SETTING. Then press the

button.

1 Press ë buttons to choose BBE.

■ 67(5(2#2#,‡,,

When you are viewing a bilingual broadcast programme, you

can choose the sound from Bilingual I (Sub I) or Bilingual II

(Sub II). When the stereo broadcasting is received poorly, you

can change from stereo to mono sound so that you can hear

the broadcast more clearly and easily.

2 Press ì buttons to choose ON.

To cancel the BBE function:

Press ì buttons to choose OFF.

3 Press the

ting.

button to complete the set-

Press

buttons to choose STEREO / I • II.

buttons to choose a sound

The menu disappears.

2 Press

mode.

•

Licensed by BBE Sound, Inc. BBE is a registered trade-

mark of BBE Sound, Inc.

E :Stereo sound

H :mono sound

ýF :Bilingual I (sub I)

■ +<3(5#6281'

You can enjoy sounds with a wider ambience.

ýG :Bilingual II (sub II)

3 Press the

ting.

button to complete the set-

1 Press ë buttons to choose HYPER

SOUND.

The menu disappears.

2 Press ì buttons to choose ON.

Note:

To cancel the HYPER SOUND function:

Press the ì buttons to choose OFF.

• The sound mode you can choose differs depending

on the TV programme.

• This function does not work in the EXT modes. And

this function does not appear in the SOUND SET-

TING menu.

3 Press the

ting.

button to complete the set-

The menu disappears

Note:

■ 6RXQG#$GMXVWPHQW

You can adjust the sound to your liking.

• The HYPER SOUND function does not work properly

with mono sound.

• The HYPER SOUND lamp lights while the HYPER

SOUND function is in use.

1 Press the ë buttons to choose an item.

• You can turn on or off the HYPER SOUND function

with a single press. For details, see “4 HYPER

SOUND Button” on page 12.

2 Press the ì buttons to adjust it.

Item

BASS

Weaker

Left

Stronger

Right

TREBLE

BALANCE

3 Press the

ting.

button to complete the set-

The menu disappears.

(;7#6(77,1*

3 Press the

ting.

button to complete the set-

The menu disappears.

Note:

• The EXT-1 terminal does not support S-VIDEO signal

(Y/C signal) and you cannot set K (S-VIDEO input)

in the EXT-1 terminal.

• Setting K (S-VIDEO input) changes the head

character from “E” to “S”. For example, “E2” is

changed to “S2”.

To display EXT SETTING menu:

•

Even an device which enables the S-VIDEO signal (Y/

C signal) to be output may output a regular video sig-

nal (composite signal) depending on the device set-

ting. If a picture cannot appear because K (S-

VIDEO input) setting has been made, read the device

Instruction Manual carefully again to check for the de-

vice settings.

1 Press the

button to display MENU

(main menu).

2 Press the ë button to choose EXT SET-

TING. Then press the button.

■ K+609,'(2#LQSXW,

When connecting a device (such as S-VHS VCR) which en-

ables an S-VIDEO signal (Y/C signal) to be output, you can

enjoy high-quality picture of the S-VIDEO signal (Y/C signal).

■ /,67

You can have a name corresponding to the devices connect-

ed for each EXT terminal. Giving a name to an EXT terminal

makes the EXT terminal number appear on the screen, to-

gether with the name.

Preparation:

• At first, read the Device Instruction Manual and “ADDITION-

AL PREPARATION” on page 32 to connect the device to the

TV properly. Second, follow the Device Instruction Manual

to set the device so that a S-VIDEO signal (Y/C signal) can

be output to the TV.

1 Press the ë buttons or ì buttons to

choose an EXT terminal.

• Do not set K(S-VIDEO input) to the EXT terminal con-

nected to a device which cannot output a S-VIDEO (Y/C sig-

nal). If it is set wrongly, a picture cannot appear.

EXT-1

1 Press the

buttons or

buttons to

EXT-3

choose an EXT terminal.

EXT-2

EXT-4

EXT-1

EXT-3

2 Press the blue button to display the name

list (LIST).

EXT-2

EXT-4

2 Press the yellow button and set the K

(S-VIDEO input).

A K (S-VIDEO input) mark is displayed. You can view

an S-VIDEO signal (Y/C signal) instead of the regular

video signal (composite signal).

To cancel the K (S-VIDEO input) setting:

Press the yellow button and turn off K (S-VIDEO in-

put) mark.

The regular video signal (composite signal) pictures are

resumed.

EXT SETTING

3 Press the ë buttons to choose a name.

Then press the

button.

The LIST disappears and the name is assigned to the

EXT terminal.

To erase a name assigned to the EXT terminal:

Choose a blank space.

4 Press the

ting.

button to complete the set-

The menu disappears.

Note:

• You cannot assign an EXT terminal name not found

in the name list (LIST).

■ '8%%,1*

You can choose a signal source to be output from an EXT-2

terminal.

You can choose any one of the output signal of the device

connected to the EXT terminal and the picture and sound

from a TV channel you are currently viewing to output it to the

EXT-2 terminal.

1 Press the ì buttons to choose the EXT-2

terminal.

2 Press the ë buttons to choose an EXT

terminal or TV.

The arrow in the menu represents a signal flow. The left

side of the arrow denotes a signal source output from the

EXT-2 terminal.

EXT-1/EXT-3/EXT-4:

The output signal of the device connected to an EXT ter-

minal passes through the TV and is output from the EXT-

2 terminal.

TV:

The picture and sound of the TV channel you are cur-

rently viewing are output from the EXT-2 terminal.

3 Press the

ting.

button to complete the set-

The menu disappears.

Note:

• During dubbing, you cannot turn off the TV. Turning

off the TV also turns off the output from the EXT-2 ter-

minal.

• When you choose an EXT terminal as an output, you

can view a TV programme or a picture from the other

EXT terminal while dubbing the picture from a de-

vice connected to the EXT terminal onto a VCR con-

nected to the EXT-2 terminal.

• The RGB signals from the TV games cannot be out-

put.Teletext programmes cannot be output.

)($785(6

■ %/8(#%$&.

You can set the TV to automatically change to a blue screen

and mute the sound if the signal is weak or absent, or when

there is no input from an external device.

1 Press the

BACK.

buttons to choose BLUE

2 Press theì buttons to choose ON.

To display the FEATURES menu:

1 Press the

button to display MENU

To cancel the BLUE BACK function:

Press theì buttons to choose OFF.

(main menu).

2 Press theë button to choose FEATURES.

3 Press the

ting.

button to complete the set-

Then press the

button.

The menu disappears.

■ 6/((3#7,0(5

You can set the TV to automatically turn off after a specified

period of time.

■ &+,/'#/2&.

When there is a TV channel you wish your children not to

watch, you can use the CHILD LOCK function to lock out the

TV channel. Even when a child chooses a Programme num-

ber (PR) in which a locked TV channel has been registered,

1 Press the

buttons to choose SLEEP

TIMER. Then press the

A Sub-menu of the SLEEP TIMER function appears.

button.

the screen will change to blue and displays (CHILD LOCK)

so the TV channel cannot be viewed. Unless you enter a pre-

set ID number by a special operation, the lock cannot be re-

leased and the child cannot view the TV channel programs.

7R#VHW#WKH#&+,/'#/2&.#IXQFWLRQ

1 Press the ë buttons to choose CHILD

LOCK. Then press theA button.

“SET ID NO.” (ID number setting screen) appears.

2 Press the

time.

buttons to set the period of

You can set the period of time a maximum of 120 min-

utes (2 hours) in 10 minute increments.

To cancel the SLEEP TIMER function:

Press the ï button to set a period of time to “OFF.”

2 Set the ID number to your liking.

3 Press the

tings.

button to complete the set-

1 Press theë buttons to choose a number.

2 Press theì buttons to move the cursor.

The menu disappears.

Note:

3 Press the

button.

• The SLEEP TIMER lamp lights while the SLEEP TIM-

ER function is operating.

The Sub-menu of CHILD LOCK appears.

• One minute before the SLEEP TIMER function turns

off the TV, “GOOD NIGHT!” appears.

• The SLEEP TIMER function cannot be used to turn

off the TV’s main power.

• When the SLEEP TIMER function is on, you can dis-

play the Sub-menu of the SLEEP TIMER function

again to confirm and/or change the remaining peri-

od of time of the SLEEP TIMER function. Press the

button to exit the menu after confirming and / or

changing the remaining time.

4 Press theë buttons to choose a TV

channel.

Every time you press the ë buttons, the Programme

number (PR) changes, and the picture of the TV channel

registered in the Programme number (PR) is displayed

on the screen.

FEATURES

5 Press the blue button and set the CHILD

LOCK function.

■ '(&2'(5#+(;705,

Only when connecting a Decoder with a T-V LINK compatible

VCR connected to the EXT-2 terminal, you can use this func-

tion. To operate this function, see “Using the DECODER

(EXT-2) function” on page 30.

(CHILD LOCK) appears and the TV channel is locked.

To reset the CHILD LOCK function:

Press the blue button again.

(CHILD LOCK) disappears.

Caution:

• If you have not connected a Decoder with a T-V LINK com-

patible VCR connected to the EXT-2 terminal, setting this

function to “ON” by mistake causes the picture/sound of a

TV channel you are currently viewing not to be issued.

6 Press the

ting.

button to complete the set-

The menu disappears.

Note:

• To disable easy resetting of the CHILD LOCK func-

tion, the menu disappears by choosing the CHILD

LOCK function and pressing the

ordinary menu operation.

button as in the

7R#YLHZ#D#ORFNHG#79#FKDQQHO

1 Choose a Programme number (PR) in

which a TV channel locked with the

Number buttons or PR LIST.

The screen changes to blue and the (CHILD LOCK)

appears. You cannot view the TV channel.

2 Press the

(Information) button to

display “ID NO.” (ID No. input screen).

3 Press the Number buttons to enter the ID

number.

The lock is temporarily released so you can view the TV

channel.

If you have forgotten the ID number:

Perform step 1 of “To set the CHILD LOCK function”. Af-

ter confirming the ID number, press the

the menu.

button to exit

Note:

• Even if you reset the lock temporarily, it does not

mean that the CHILD LOCK function set for the TV

channel is cancelled. The next time anyone at-

tempts to view the TV channel, it will be locked

again.

• When you would like to cancel the CHILD LOCK

function, you must perform the operation “To set the

CHILD LOCK function” again.

• To disable easy choosing of a Programme number

(PR) in which a locked TV channel has been regis-

tered, the Programme number (PR) has been set

that it cannot be chosen by the

operation buttons at the TV.

buttons or the

• To disable easy resetting of the lock, “ID NO.” (ID

No. input screen) is set so that it cannot appear un-

less you press the

(Information) button.

,167$//

To cancel the AUTO PROGRAM function:

Press the button.

3 After the TV channels have been regis-

tered in the Programme numbers (PR), the

EDIT menu appears.

You can proceed to edit the Programme numbers (PR)

using the EDIT/MANUAL function. For details, see “ED-

IT/MANUAL” on page 26.

To display the INSTALL menu:

When not using the EDIT/MANUAL function:

If you do not need to use the EDIT/MANUAL function, go

to the next step.

1 Press the

button to display MENU

(main menu).

2 Press the

button to choosetheINSTALL

4 Press the

menu.

button to display the T-V LINK

menu. Then press the

button.

■ /$1*8$*(

You can choose the language you want to use for the on-

screen display from the language list in a menu.

1 Press the

buttons to choose LAN-

GUAGE. Then press the

A sub-menu of the LANGUAGE function appears.

button.

5 Operate the T-V LINK menu according to

the type of VCR connected to the EXT-2

terminal.

When a T-V LINK compatible VCR is not con-

nected:

Press the

button to exit the T-V LINK menu.

The T-V LINK menu disappears, and all the settings are

completed.

When a T-V LINK compatible VCR is connected:

Follow the operating procedure “Downloading the data

to VCR” on page 30 to transmit the Programme number

(PR) data to the VCR.

2 Press the

guage.

buttons to choose a lan-

Note:

3 Press the

ting.

button to complete the set-

• When your TV can detect the TV channel name from

the TV channel broadcast signal, it automatically

registers the TV channel name (ID) to the Pro-

gramme number (PR) in which the TV channel has

been registered.

The menu disappears.

• If a TV channel you want to view is not set to a Pro-

gramme number (PR), manually set it using the

MANUAL function. For details, see “EDIT/MANUAL”

on page 26.

■ $872#352*5$0

You can automatically register the TV channels which can be

received well at your residence in the TV’s Programme num-

bers (PR) by performing the following.

• The TV channel is not registered in Programme

number PR 0 (AV). When you want to register a TV

channel to PR 0 (AV) manually set it using the MAN-

UAL function. For details, see “EDIT/MANUAL” on

page 26.

1 Press the

buttons to choose AUTO

PROGRAM.

2 Press the

button to start the AUTO

PROGRAM function.

The AUTO PROGRAM menu appears and received TV

channels are automatically registered in the Programme

numbers (PR).

INSTALL

2 Follow the operation description of a func-

tion you want to use and operate the func-

tion.

■ (',720$18$/

The EDIT/MANUAL functions are divided into two types: ed-

iting of the current Programme numbers (PR) (EDIT func-

tions) and manual registration of a TV channel you want to

view to the Programme number (PR) (MANUAL function).

The details about these functions are as follows:

3 Press the

tings.

button to complete the set-

The T-V LINK menu appears.

MOVE:

This function changes a Programme number (PR) of a TV

channel.

ID:

This function registers a Channel name (ID) to a TV channel.

INSERT:

This function adds a new TV channel in the current Pro-

gramme numbers (PR) list by using the CH/CC number.

4 Operate the T-V LINK menu according to

the type of VCR connected to the EXT-2

terminal.

DELETE:

This function deletes a unnecessary TV channel.

When a T-V LINK compatible VCR is not con-

nected:

MANUAL:

This function manually registers a new TV channel in a Pro-

gramme number (PR).

Press the

button to exit the T-V LINK menu.

The T-V LINK menu disappears and all the settings are

completed.

Caution:

When a T-V LINK compatible VCR is connected:

• Using the MOVE, DELETE or INSERT function rewrites the

current Programme numbers (PR) list. Resultingly, the Pro-

gramme number (PR) of some of the TV channels will

change.

Follow the operating procedure “Downloading the data

to VCR” on page 30 to transmit the Programme number

(PR) data to the VCR.

• Using the MANUAL function for a TV channel for which the

CHILD LOCK function has been set cancels the CHILD

LOCK function for the TV channel.

029(

1 Press the

channel.

buttons to choose a TV

• Using the MANUAL function for a TV channel for which the

DECODER (EXT-2) function has been set to ON returns the

setting of the DECODER (EXT-2) function for the TV chan-

nel to OFF.

Every time you press the

buttons, the Programme

number (PR) is changed over, and the picture of the TV

channel registered in the Programme number (PR) ap-

pears on the screen.

• When a TV channel has already been registered in PR 99,

using the INSERT function deletes the TV channel.

2 Press the button to start the MOVE func-

Note:

tion.

• For Programme number PR 0, “AV” appears in the Pro-

gramme numbers (PR) list.

• An EXT terminal number does not appear in the Pro-

gramme numbers (PR) list.

• The CH/CC number is a number unique to the TV and

corresponding to the Channel number of a TV channel.

For the relationship of a Channel number and a CH/CC

number, see “CH/CC NUMBER” on page 28.

• You cannot use the INSERT function if you do not know a

Channel number of a TV channel. Use the MANUAL func-

tion to register a TV channel in the Programme number

(PR).

3 Press the

buttons to choose a new

Programme number (PR).

1 Press the

buttons to choose EDIT/

button.

MANUAL. Then press the

To cancel the MOVE function:

Press the (Information) button.

INSTALL

4 Press the button to change the Pro-

Note:

gramme number (PR) of a TV channel to a

new Programme number (PR).

• You can register your unique Channel name (ID) to

the TV channel. When step 3 is completed, do not

go to step 4, but press the

buttons to move the

buttons to choose a character for

completing the Channel name (ID). Then press the

button to register the Channel name (ID) to the TV

cursor and the

1 Press the

channel.

buttons to choose a TV

channel.

Every time you press the

buttons, the Programme

number (PR) is changed over, and the picture of the TV

channel registered in the Programme number (PR) ap-

pears on the screen.

,16(57

Preparation:

• A CH/CC number unique to this TV and corresponding to

the Channel number of a TV channel is required. Find the

corresponding CH/CC number from a table “CH/CC

NUMBER” on page 28 based on the Channel number of the

TV channel.

2 Press the red button to start the ID func-

tion.

1 Press the

buttons to choose a Pro-

gramme number (PR) for which you will

2 Press the green button and start the IN-

SERT function.

3 Press the

buttons to choose the first

character of a Channel name (ID) you want

to attach to the TV channel.

To cancel the INSERT function:

Press the

(Information) button.

3 Press the

buttons to choose “CC” or

“CH” according to the CH/CC number of

the TV channel.

4 Press the blue button to display the ID LIST

(channel name list).

To cancel the INSERT function:

Press the

(Information) button.

4 Press the Number button to enter the re-

maining CH/CC number.

The TV shifts to registration mode.

When the registration is completed, the picture of the TV

channel appears on the screen.

Note:

• The CH/CC number is a number indicating the

broadcast frequency to the TV. If the TV cannot de-

tect the TV channel corresponding to the broadcast

frequency indicated by the CH/CC number, a pic-

ture in the no-signal state appears.

5 Press the

nel name (ID).

buttons to choose the Chan-

To cancel the ID function:

Press the

(Information) button.

6 Press the

button to register a Channel

name (ID) to a TV channel.

INSTALL

'(/(7(

■ &+2&&#180%(5

1 Press the ë buttons to choose a TV

• When you want to use the INSERT function on page 27,

find the CH/CC number corresponding to the Channel

number of the TV channel from this table.

channel.

Every time you press the ë buttons, the Programme

number (PR) is changed over, and the picture of the TV

channel registered in the Programme number (PR) ap-

pears on the screen.

Channel

E40

E41

E42

E43

E44

E45

E46

E47

E48

E49

E50

E51

E52

E53

E54

E55

E56

E57

E58

E59

E60

E61

E62

E63

E64

E65

E66

E67

E68

E69

CH 02 / CH 202

CH 03 / CH 203

CH 04 / CH 204

CH 05 / CH 205

CH 06 / CH 206

CH 07 / CH 207

CH 08 / CH 208

CH 09 / CH 209

CH 10 / CH 210

CH 11 / CH 211

CH 12 / CH 212

CH 21 / CH 221

CH 22 / CH 222

CH 23 / CH 223

CH 24 / CH 224

CH 25 / CH 225

CH 26 / CH 226

CH 27 / CH 227

CH 28 / CH 228

CH 29 / CH 229

CH 30 / CH 230

CH 31 / CH 231

CH 32 / CH 232

CH 33 / CH 233

CH 34 / CH 234

CH 35 / CH 235

CH 36 / CH 236

CH 37 / CH 237

CH 38 / CH 238

CH 39 / CH 239

E2, IR A

CH 40 / CH 240

CH 41 / CH 241

CH 42 / CH 242

CH 43 / CH 243

CH 44 / CH 244

CH 45 / CH 245

CH 46 / CH 246

CH 47 / CH 247

CH 48 / CH 248

CH 49 / CH 249

CH 50 / CH 250

CH 51 / CH 251

CH 52 / CH 252

CH 53 / CH 253

CH 54 / CH 254

CH 55 / CH 255

CH 56 / CH 256

CH 57 / CH 257

CH 58 / CH 258

CH 59 / CH 259

CH 60 / CH 260

CH 61 / CH 261

CH 62 / CH 262

CH 63 / CH 263

CH 64 / CH 264

CH 65 / CH 265

CH 66 / CH 266

CH 67 / CH 267

CH 68 / CH 268

CH 69 / CH 269

E3, IR B, ITALY A

E4, IR C, ITALY B

E5, IR D, ITALY D

2 Press the yellow button to delete the TV

channel.

E6, IR E, ITALY E

E7, IR F, ITALY F

E8, IR G

The TV channel is deleted from the Programme num-

bers (PR) list.

E9, ITALY G

E10, IR H, ITALY H

E11, IR J, ITALY H+1

E12, ITALY H+2

E21

E22

E23

E24

E25

E26

E27

E28

E29

E30

E31

0$18$/

1 Press the

E32

E33

buttons to choose a Pro-

E34

E35

gramme number (PR) to which you want to

E36

E37

E38

E39

2 Press the blue button to activate the MAN-

UAL function.

Channel

S31

CC 01 / CC 201

CC 02 / CC 202

CC 03 / CC 203

CC 04 / CC 204

CC 05 / CC 205

CC 06 / CC 206

CC 07 / CC 207

CC 08 / CC 208

CC 09 / CC 209

CC 10 / CC 210

CC 11 / CC 211

CC 12 / CC 212

CC 13 / CC 213

CC 14 / CC 214

CC 15 / CC 215

CC 16 / CC 216

CC 17 / CC 217

CC 18 / CC 218

CC 19 / CC 219

CC 20 / CC 220

CC 21 / CC 221

CC 22 / CC 222

CC 23 / CC 223

CC 24 / CC 224

CC 25 / CC 225

CC 26 / CC 226

CC 27 / CC 227

CC 28 / CC 228

CC 29 / CC 229

CC 30 / CC 230

CC 31 / CC 231

CC 32 / CC 232

CC 33 / CC 233

CC 34 / CC 234

CC 35 / CC 235

CC 36 / CC 236

CC 37 / CC 237

CC 38 / CC 238

CC 39 / CC 239

CC 40 / CC 240

CC 41 / CC 241

CC 75 / CC 275

CC 76 / CC 276

CC 77 / CC 277

CC 78 / CC 278

CC 79 / CC 279

S32

S33

S34

S35

S36

S37

S38

S39

S10

S11

S12

S13

S14

S15

S16

S17

S18

S19

S20

S21

S22

S23

S24

S25

S26

S27

S28

S29

S30

S40

S41

To cancel the MANUAL function:

Z, ITALY C

Z+1

Press the

(Information) button.

Z+2

3 Press the green or red button to search for

a TV channel.

Scanning stops when the TV finds a TV channel. Then

the TV channel is displayed.

4 Press the green or red button repeatedly

until the TV channel you want appears.

If the TV channel reception is poor:

Press the blue or yellow button to fine-tune the TV chan-

nel.

5 Press the

button and register the TV

channel to a Programme number (PR).

The normal EDIT menu is resumed.

'(02

To display the DEMO menu:

1 Press the

button to display MENU

(main menu).

2 Press theë button to choose DEMO. Then

press the button.

The DEMO function automatically demonstrates some of the

TV functions.

1 Press the ë buttons to choose ON.

2 Press the

tings.

button to complete the set-

The DEMO function is set to ON, and the demonstration

will start.

To stop the demonstration:

Press one of the buttons on the remote

control.

When the DEMO function is set to ON:

Each time the TV is turned on, the demonstration starts

automatically. If you do not want that to happen, perform

the following operations to cancel the DEMO function:

1 Display the DEMO menu again.

2 Press the ë buttons to choose OFF.

3 Press the

function.

button to cancel the DEMO

$'',7,21$/#0(18#23(5$7,216

4 Press the

buttons to choose FEA-

■ 'RZQORDGLQJ#WKH#GDWD#WR#9&5

You can transmit to the latest Programme numbers (PR) data

to the VCR with the T-V LINK function.

TURES. Then press the

button.

The FEATURES menu appears.

Caution:

• Only when the T-V LINK compatible VCR is connected to

the EXT-2 terminal, this operation is enabled.

• Only when the T-V LINK menu is being displayed, this oper-

ation is enabled.

5 Press the

buttons to choose DECOD-

ER (EXT-2) . Then press the

choose ON.

buttons to

An unscrambled picture appears.

To cancel the DECODER (EXT-2) function:

Press the buttons to choose OFF.

1 Turn on the VCR.

6 Press the

ting.

button to complete the set-

2 Press the

button.

The data transmission begins.

The T-V LINK menu appears.

The T-V LINK menu disappears once the data transmis-

sion ends.

When the T-V LINK menu is changed over to

another menu:

The menu operation at the TV side is completed and it is

shifted to the menu operation at the VCR side. Refer to

the VCR Instruction Manual and operate the VCR.

7 Follow the operating procedure “Down-

loading the data to VCR” on page 30 to

transmit the Programme number (PR) data

to the VCR.

Note:

• If “FEATURE NOT AVAILABLE” appears at the T-V

LINK menu, ensure the following three items are cor-

rect; then press the

sion.

button to retry data transmis-

8 If you have another TV channel capable of

being unscrambled with a Decoder, repeat

steps 2 through 7.

− Has the T-V LINK compatible VCR been connect-

ed to the EXT-2 terminal?

− Has the VCR power been turned on?

Note:

− Does the SCART cable that is connected to the

EXT-2 terminal to T-V LINK compatible VCR have

all proper connections?

• If for some reason the DECODER (EXT-2) function

has been set to “ON” but the TV channel cannot be

unscrambled, check the following:

− Has the Decoder been connected to the VCR

properly according to the VCR and Decoder In-

struction Manuals?

■ 8VLQJ#WKH#'(&2'(5#+(;705,##

− Has the Decoder power been turned on?

IXQFWLRQ

−

Can the TV channel be unscrambled with a De-

coder?

When connecting a Decoder with a T-V LINK compatible VCR

connected to the EXT-2 terminal, use the DECODER (EXT-2)

function to unscramble the scrambled TV channels.

− Is it necessary to change the VCR settings in or-

der to connect the Decoder? Confirm that the

VCR is set properly by rechecking the VCR In-

struction Manual.

1 Turn on the Decoder power.

2 Display the TV channel capable of being

unscrambled with the Decoder on the TV.

Even if the Decoder is functioning, a scrambled picture

appears at this time.

3 Press the

button to display the MENU.

The MENU (main menu) appears.

ADDITIONAL MENU OPERATIONS

■ 6HWWLQJ#WKH#63($.(5#IXQFWLRQ

Turn off the SPEAKER function so that TV speakers will not

issue any sound.

1. Press the

button to display the MENU

(main menu).

2. Press the

buttons to choose SOUND

SETTING. Then press the

play the SOUND SETTING menu.

button to dis-

The SOUND SETTING menu appears.

3. Press the

buttons to choose SPEAK-

ER. Then press the

OFF.

buttons to choose

The sound from the TV speakers are cut.

4. Press the

tings.

button to complete the set-

The menu disappears.

Note:

• The ì buttons of the TV remote control and the D

(volume) buttons at the front panel of your TV set can be

used to control the volume of each speaker simultane-

ously.

• Setting the volume of the amplifier too high may damage

the front speakers.

$'',7,21$/#35(3$5$7,21

■ &RQQHFWLQJ#WKH#H[WHUQDO#GHYLFHV

Connect the devices to the TV, paying attention to the Rear

panel connections and the Front panel connections.

Before connecting anything:

• Read the manuals provided with the devices. Depending

on the devices, the connection method may differ from

the figure. In addition, the device settings may be

changed depending on the connection method to secure

proper operation.

• Turn off all the devices including the TV.

(Behind the door)

• The “SPECIFICATIONS” on the back cover contains the

details of the EXT terminals. If you are connecting a de-

vice not listed in the following connection diagram, see

the table to choose the best EXT terminal.

• Note that connecting cables are not supplied.

1 VCR (composite signal)

2 VCR (composite signal/S-VIDEO signal)

3 T-V LINK compatible VCR (composite signal/S-VIDEO sig-

nal)

4 Decoder

5 DVD player (composite signal/S-VIDEO signal)

6 DVD player (composite signal/RGB signal)

7 TV game (composite signal/RGB signal)

8 TV game (composite signal/S-VIDEO signal)

9 Headphones

0 Camcorder (composite signal/S-VIDEO signal)

- SCART cable

= Audio cable

~ Video cable

! S-VIDEO cable

EXT-2

EXT-3

EXT-1

AUDIO OUT

ADDITIONAL PREPARATION

'HYLFHV#ZKLFK#FDQ#RXWSXW#WKH#

609,'(2#VLJQDO#+<2&#VLJQDO,#VXFK#DV

D#609+6#9&5

■ &RQQHFWLQJ#6SHDNHUV2$PSOL0

ILHU

While referring to the Audio equipment connection diagram,

connect the audio equipment you desire to the TV.

You can use external front speakers to listen to the TV sound

instead of the TV speakers. For details of how to operate

them, see “Setting the SPEAKER function” on page 31.

Connect the device to an EXT terminal other than the EXT-1

terminal.

You can choose a video input signal from the S-VIDEO signal

(Y/C signal) and regular video signal (composite signal). For

details of how to operate the device, see “K(S-VIDEO in-

put)” on page 21.

Before connecting anything:

• Read the manuals provided with the amplifier and speak-

ers.

709#/,1.#FRPSDWLEOH#9&5

• Turn the TV and Amplifier off.

Be sure to connect the T-V LINK compatible VCR to the EXT-

2 terminal. If not, the T-V LINK function will not work properly.

• To prevent magnetism from the speakers adversely ef-

fecting the TV screen, use magnetic-shielded speakers

for the front speakers.

Note:

• When connecting a T-V LINK compatible VCR to the EXT-

2 terminal, be sure to connect the Decoder to the VCR. If

not, the T-V LINK function may not work properly. After

you have registered TV channels to the Programme num-

bers (PR), set the DECODER (EXT-2) function for the Pro-

gramme number (PR) to ON in order to unscramble a

scrambled TV channel. For details of operation, see “Us-

ing the DECODER (EXT-2) function” on page 30.

• Note that connecting cables are not supplied.

AUDIO OUT

(Terminals on rear)

&RQQHFWLQJ#KHDGSKRQHV

Connect the headphones with a stereo mini-jack (of 3.5mm in

diameter) to the headphone jack at the TV front panel.

1 Amplifier

2 Front speakers (Magnetic-shielded type)

Note:

• When you connect the headphones, the TV speakers is-

sue no sound.

• The output from the AUDIO OUT terminal is not interrupt-

ed by headphone connection to the TV. You cannot cut

the sound from the front speaker even if you connect a

headphone to the TV.

9LGHR2VRXQG#VLJQDO#RXWSXW#IURP#WKH

(;705#WHUPLQDO

You can arbitrarily change over the output of the video/sound

signal from the EXT-2 terminal. It is useful when you want to

dub the video/sound from another device on the VCR con-

nected to the EXT-2 terminal. For details on how to do this op-

eration, see “DUBBING” on page 22.

79#RXWSXW#IURP#WKH#(;704#WHUPLQDO

The output of video/sound signal of a TV channel you are cur-

rently viewing is always output from the EXT-1 terminal.

Note:

• Changing over a Programme number (PR) also changes

over the TV output from the EXT-1 terminal.

• The video/sound signal from an EXT terminal cannot be

output.

• Teletext programmes cannot be output.

79#%877216#$1'#3$576

■ )URQW#3DQHO

Push to open

(Behind the cover)

1 EXT-4 terminal

pages 21 and 32

pages 32

7 HYPER SOUND lamp

8 ECO lamp

pages 12 and 20

page 17

2 Headphone jack (mini jack)

3 D (Volume) button

^{4 P}∨/∧ buttons / –/+ buttons

5 Remote control sensor

6 ECO sensor

page 10

9 SLEEP TIMER lamp

0 Power lamp

page 23

page 10

pages 5 and 8

- Main power button

Caution:

• Do not grasp the TV by the front panel cover when moving the TV set. If you do, you may break the cover.

■ 5HDU#3DQHO

EXT-2

EXT-3

EXT-1

AUDIO OUT

= AUDIO OUT terminal

~ Aerial socket

page 33

page 4

@ EXT-2 terminal

pages 4, 7, 21 and 32

pages 21 and 32

# EXT-3 terminal

! EXT-1 terminal

pages 4, 21 and 32

7528%/(6+227,1*

If a problem arises while you are using the TV, please read this “Troubleshooting” well before you request having the TV repaired.

You may be able to fix it easily by yourself. For example, if the AC plug is disconnected from the AC outlet, or the TV aerial has

problems, you may think there is a problem with the TV itself.

Important:

• This Troubleshooting guide only covers problems whose cause are not easy to determine. If a question arise when you are

operating a function, read the page(s) corresponding to the operation of the function well, not this Troubleshooting guide.

• After you have followed the Troubleshooting description or the operating description of the functions concerned without any suc-

cess, remove the AC plug from the AC outlet and request a repair of your TV. Do not attempt to repair the TV by yourself or

remove the rear cover of the TV.

• When the TV channel reception is poor, it can be hard to

,I#\RX#FDQQRW#WXUQ#RQ#WKH#79

hear the stereo or bilingual sound. In this case, follow the

• Is the AC plug connected to the AC outlet?

description “STEREO / I•II” on page 20 to hear the sound

more easily by changing it to a mono sound.

• Is the Power lamp lit? If not, press the Main power button.

2SHUDWLRQ#GLVDEOHG

1R#SLFWXUH21R#VRXQG

• Have the batteries of the remote control become exhaust-

ed? Follow the description “Putting Batteries into the Re-

mote Control” on page 4 and replace them with new

batteries to try to solve the problem.

• Have you chosen a TV channel whose reception is extreme-

ly bad? In this case, the BLUE BACK function will be activat-

ed, the entire screen becomes blue, and the sound is muted.

In spite of this, if you want to view the TV channel, follow the

description “BLUE BACK” on page 23 to try to change the

BLUE BACK function setting to OFF.

• Have you attempted to use the remote control at the sides

or rear of the TV or at a location more than seven meters

apart from the TV location? Operate the remote control in

the front of your TV or a location less than seven meters

from your TV to try to solve the problem.

• Have you connected the headphones to the TV? Connect-

ing the headphones to the TV causes sounds not to be is-

sued from the TV speakers.

• When you are viewing a teletext programme, you cannot op-

• Have you set the SPEAKER function to OFF? Follow the de-

scription “SPEAKER” on page 20 to confirm the SPEAKER

function setting to try to solve the problem.

erate the menus. Press the

button to return the teletext

programme to the ordinary TV programme to try operating

the menus.

3RRU#SLFWXUH

• If noise totally obscures the picture (snow), the aerial or aer-

ial cable may have trouble. Check the following to try to

solve the trouble:

• If the TV operation becomes disabled suddenly, press the

Main power button on the TV and turn off the main power.

Try to press the Main power button again to turn on the main

power. If the TV returns to a normal state, it is not a failure.

Has the TV and aerial been connected properly?

Has the aerial cable been damaged?

Is the aerial pointed to the right direction?

Is the aerial itself faulty?

2WKHU#FRQFHUQV

• When the SLEEP TIMER function operates, the TV is auto-

matically turned off. If the TV is turned off suddenly, try to

press the

(Standby) button to turn on the TV once

again. At this time, if the TV resumes a normal state, there

• If the TV or aerial receives interference from the other devic-

es, stripes or noise may appear in the picture. Move such

devices as an amplifier, personal computer, or a hair drier

that can cause interference away from your TV, or try

changing its location. If the aerial suffers interference from a

radio tower or high-voltage wire, please contact your local

dealer.

is no problem.

• When the TV is receiving a wide-screen signal (WSS) or a

signal concerning the screen size from an external device,

the ZOOM mode automatically changes. When you want to

resume the previous ZOOM mode, press the ZOOM button

again.

• If the TV receives interference from signal reflecting from

mountains or building, double-pictures (ghosting) will occur.

Try to change the aerial’s direction or replace the antenna

with the one with better directionality.

• If you bring a magnetised device such as a speaker near to

your TV, a picture may be warped or unnatural colors ap-

pear at he corners of the screen. In this case, keep the de-

vice apart from your TV. If the speakers causes such

phenomena, use the magnetic-shielded speakers instead.

• Are your COLOUR SYSTEM settings correct? Follow the

description “COLOUR SYSTEM” on page 18 to try to solve

the trouble.

• A picture may be tited due to the influence of the earth’s

magnetism. In this case, use the “PICTURE TILT” on

page 19 to complete the tilt.

• Has COLOUR or BRIGHT been controlled properly? Follow

the description “Picture Adjustment” on page 17 to try to ad-

just them properly.

• The TV may emit a crackling sound due to a sudden change

in temperature. It does not matter if a picture or sound does

not show any abnormality. If you hear crackling sounds fre-

quently while you are viewing the TV, other causes may be

assumed. For precautionary purposes, request your service

technician to inspect it.

• Videotaping teletext is not recommended because it may

not record correctly.

• When a white and bright still image (such as a white dress)

is displayed on the screen, the white part may look as if it

were coloured. It is a phenomenon unavoidable due to the

nature of the picture tube itself, and not due to a TV failure.

When the picture disappears from the screen, the unnatural

colours will also disappear.

• Touching the screen may cause you feel a slight electric

shock due to its static electricity. It is an unavoidable phe-

nomenon due to the construction of the picture tube. It is not

a problem with the TV. You can rest assured that this static

discharge does not have harmful influence over the human

body.

3RRU#VRXQG

• Have you adjusted BASS or TREBLE properly? If not, follow

the description “Sound Adjustment” on page 20 to try to ad-

just them properly.

63(&,),&$7,216

Model

AV-28WFT1EI*

Item

Broadcasting systems

Colour systems

CCIR I

PAL

•

The EXT terminals also support the NTSC 3.58/4.43 MHz system.

Channels and frequencies

Sound-multiplex systems

Teletext systems

Power requirements

Power consumption

Picture tube size

Audio output

IR A-J, E2-E12, E21-E69, S1-S41, X, Y, Z, Z+1, Z+2, ITALY A-H, ITALY H+1, ITALY H+2

NICAM (I) system

FLOF (Fastext), WST (World Standard Text)

220 - 240 V AC, 50 Hz

Maximum: 168 W, Average: 115 W, Standby: 0.8 W

Viewable area 66 cm (measured diagonally)

Rated Power output: 7.5 W + 7.5 W

Speakers

(16cm × 4cm) oval × 2

EXT-1 terminal

Euroconnector (21-pin, SCART)

•

Video input, Audio L/R inputs and RGB inputs are available.

TV broadcast outputs (Video and Audio L/R) are available.

EXT-2 terminal

Euroconnector (21-pin, SCART)

•

Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.

Video and Audio L/R outputs are available.

T-V LINK functions are available.

EXT-3 terminal

EXT-4 terminal

Euroconnector (21-pin, SCART)

Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.

•

RCA connectors × 3

S-VIDEO connector × 1

•

Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.

AUDIO OUT terminal

RCA connectors × 2

•

Variable audio L/R outputs are available.

Variable out 0-1 Vrms, low impedance

Headphone jack

Dimensions (W × H × D)

Weight

Stereo mini-jack (3.5 mm in diameter)

780 mm × 509 mm × 499 mm

39 kg

Accessories

Remote control unit RM-C51 × 1

AAA/R03 dry cell battery × 2

* A basic model number. The actual model number may have characters added (such as “S” denoting silver) indicating

the colour of the TV set.

Design and specifications subject to change without notice.

Pictures displayed on the screen using this TV’s ZOOM functions should not be shown for any commercial or demonstration pur-

pose in public places (cafes, hotels, etc.) without the consent of the owners of copyright of the original picture sources, as this

constitutes an infringement of copyright.

LCT0622-001A-U

0300-T-CR-JMUK

JVC AV 29W33 User Manual
JVC HV 34LPZ User Manual
Magnavox 27MS343S User Manual
Marshall electronic Marshall Electronics Computer Monitor M LYNX 10W User Manual
Moffat Blue Seal G1100 User Manual
National Instruments Computer Hardware CAN Hardware User Manual
Philips 29PT6447 User Manual
Philips 200XW7EB User Manual
Philips Computer Monitor 29PFL4508 User Manual
Philips HWC8200T User Manual