JVC GD V4210PZW G User Manual

INSTRUCTIONS

Model

GD-V4210PZW

GD-V4210PZW-G

GD-V4210PCE

GD-V4210PCE-G

GD-V4211PCE

Thank you for purchasing this JVC Monitor.

Before using the monitor, read this manual carefully so

that you know how to use the Monitor correctly.

Refer to this manual whenever questions or problems

about operation arise. Be sure to read and observe the

safety precautions.

Keep this manual where the user can see it easily.

* Installation and removal require special expertise.

Consult your product dealer for details.

This instruction manual refers to the GD-V4210PZW, GD-V4210PZW-G, GD-V4210PCE, GD-V4210PCE-G, and GD-V4211PCE.

The explanations and illustrations used in this instruction manual are of the GD-V4210PZW unless otherwise stated.

The differences between each model are as follows:

GD-V4210PZW GD-V4210PZW-G GD-V4210PCE GD-V4210PCE-G

GD-V4211PCE

Silver

Gray

Silver

Gray

Frame Colour

Inputs VIDEO A

VIDEO B

Available

Not available*¹

COMPONENT

* These inputs will be available with the separately-purchased video interface kit (IF-C421P1W).

Ask your dealer to install the video interface kit.

Contents

Page

Safety Precautions ....................................................2

Parts Identification .....................................................4

• Remote Control ...................................................4

• Monitor: Front View .............................................5

• Monitor: Rear Views ............................................6

Other Convenient Functions ....................................24

• Showing On-screen Display ............................. 24

• Confirming the Use Time...................................25

• Setting the Auto Sleep Function ....................... 25

• Prohibiting the Monitor’s Button Operations ..... 26

• Showing the On-screen When Changing

the Input Mode ..................................................26

• Mounting the Monitor Vertically ........................ 27

• Setting the High-Definition signal Types ........... 27

• Using the Pixel Shift Function........................... 27

• Using the Power Save Function ....................... 28

• Preventing the Afterimage Effect ...................... 29

• Refreshing the Screen.......................................29

• Resetting All the Setup Menu Settings ............. 29

• Resetting All the Menu Settings ....................... 30

Preparations ..............................................................9

• Checking the Accessories ...................................9

• Installing the Batteries .........................................9

Installation ...............................................................10

• Precautions .......................................................10

Connections ............................................................11

• Precautions .......................................................11

• Available Signals ...............................................11

• Connection Examples .......................................12

Basic Operations .....................................................14

• Daily Operations................................................14

• Changing the Aspect Ratio............................... 15

Serial Connections and Operations........................ 31

• Connecting the Remote Control Cables ........... 31

• Assigning ID Numbers.......................................31

• Operating the Monitors Simultaneously............ 32

• Operating the Monitors Individually .................. 32

Video Adjustments ..................................................16

• Adjusting the Picture Quality ............................ 16

• Adjusting the Screen Size and Position............ 17

• Adjusting the Color Temperature ...................... 19

• Adjusting the White Balance............................. 19

• Changing the Picture Mode .............................. 21

• Changing the Aspect Ratio............................... 21

• Setting the Receivable Signal Types ................ 22

• Setting the RGB Input .......................................23

Menu Classifications ...............................................33

• Main Menu ........................................................33

• Setup Menu .......................................................35

Troubleshooting .......................................................36

• Self-diagnostic Indication ..................................37

Specifications ..........................................................38

•

Resetting the Function Selection Menu Settings .. 23

– When the product is used on a cart, care should be taken to avoid quick stops, excessive force, and

uneven surfaces which may cause the product and cart to overturn, damaging equipment or causing

possible injury to the operator.

– Slots and openings in the cabinet are provided for ventilation. These ensure reliable operation of the

product and protect it from overheating. These openings must not be blocked or covered. (The openings

should never be blocked by placing the product on bed, sofa, rug, or similar surface. It should not be

placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided and the manufacturer’s

instructions have been adhered to.)

For proper ventilation, separate the product from other equipment, which may prevent ventilation and keep distance

more than 10 cm (3 ¹⁵/16 inches).

– This product should be operated only with the type of power source indicated on the label. If you are not sure of the

type of power supply to your home, consult your product dealer or local power company.

– This product is equipped with a three-wire plug. This plug will fit only into a grounded power outlet. If you are unable to

insert the plug into the outlet, contact your electrician to install the proper outlet. Do not defeat the safety purpose of

the grounded plug.

– Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or

against them. Pay particular attention to cords at doors, plugs, receptacles, and the point where they exit from the

product.

– For added protection of this product during a lightning storm, or when it is left unattended and unused for long periods

of time, unplug it from the wall outlet and disconnect the cable system. This will prevent damage to the product due to

lightning and power line surges.

– Do not overload wall outlets, extension cords, or convenience receptacles on other equipment as this can result in a

risk of fire or electric shock.

– Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short

out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

– Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltages

and other hazards. Refer all service to qualified service personnel.

– Unplug this product from the wall outlet and refer service to qualified service personnel under the following conditions:

a)When the power supply cord or plug is damaged.

b)If liquid has been spilled, or objects have fallen on the product.

c) If the product has been exposed to rain or water.

d)If the product operated normally by following the operating instructions. Adjust only those controls that are covered

by the Operation Manual, as an improper adjustment of controls may result in damage and will often require

extensive work by a qualified technician to restore the product to normal operation.

e)If the product has been dropped or damaged in any way.

f) When the product exhibits a distinct change in performance – this indicates a need for service.

– When replacement parts are required, be sure the service technician has used replacement parts specified by the

manufacturer or with same characteristics as the original part. Unauthorized substitutions may result in fire, electric

shock, or other hazards.

– Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to

determine that the product is in proper operating condition.

– The product should be placed more than 30 cm (11 ¹⁵/16 inches) away from heat sources such as radiators, heat

registers, stoves, and other products (including amplifiers) that produce heat.

– When connecting other products such as VCR’s, and personal computers, you should turn off the power of this product

for protection against electric shock.

– Do not place combustibles behind the cooling fan. For example, cloth, paper, matches, aerosol cans or gas lighters that

present special hazards when over heated.

– Use only the accessory cord designed for this product to prevent shock.

Parts Identification

Remote Control

DISPLAY ASPECT

POWER

RGB

VIDEO A VIDEO B COMPO.

MUTING

VOLUME

MULTIPLE MONITOR ADJUSTMENT

MODE

ID SET

MENU/EXIT

RM-C575 REMOTE CONTROL UNIT

1 Remote signal transmission w indow

6 MENU/EXIT button

Use this button to display or erase menus.

While a sub-menu is displayed, pressing this button will

move you one screen back to the preceding menu.

2 DISPLAY button (page 14)

Use this button to display the input terminal, color system

(for VIDEO A or B input), scan system (for COMPONENT

input) and horizontal/ vertical frequency (for RGB input).

Pressing the button again will make the display disappear.

7 Remote control cable jack (page 31)

Connect the remote control cable when using this remote

control as a wired remote control.

3 VIDEO A, VIDEO B, COMPO. and RGB buttons

(page 14)

8 ASPECT button (page 15)

Use these buttons to switch between inputs.

To select the correct RGB input, you have to set “RGB

INPUT” correctly on the menu (see page 23).

Use this button to switch between aspect ratios. Each time

you press the button, the aspect ratio changes as follows:

REGULAR

PANORAMIC

FULL

• Only for GD-V4210PCE, GD-V4210PCE-G and

GD-V4211PCE: Only RGB input can be reproduced.

To reproduce images through the other inputs, you need

to install video interface kit (IF-C421P1W), which is

separately purchased.

ZOOM

9 POWER button (page 14)

Use this button to turn on/ off the power.

p VOLUME + / – buttons (page 14)

Use these buttons to adjust the volume level.

4 MUTING button (page 14)

Use this button to turn off the volume immediately.

Pressing the button again will resume the previous

volume level.

q 2 / 3 / 5 / ∞ buttons

Use these buttons to select menu items or make

adjustments.

5 MULTIPLE MONITOR ADJUSTMENT buttons (page 31)

Use these buttons to set IDs, etc. when serial connection is

made.

Monitor: Front View

MENU INPUT

POWER

MENU INPUT

POWER

Bottom View

1 Remote sensor/pow er lamp

5 INPUT button (page 14)

Point the front end of the wireless remote control toward

here.

When the Monitor is turned on, the power lamp glows

green. It glows orange in standby mode.

Use this button to switch between inputs.

To select the correct RGB input, you have to set “RGB

INPUT” correctly on the menu (see page 23).

• Only for GD-V4210PCE, GD-V4210PCE-G and

GD-V4211PCE: Only RGB input can be reproduced.

To reproduce images through the other inputs, you need

to install video interface kit (IF-C421P1W), which is

separately purchased.

2 Self-diagnostic lamps (page 37)

These lamps light/ flash if something abnormal occurs

with the Monitor.

3 2 / 3 / 5 / ∞ buttons

6 POWER button (page 14)

Use these buttons to select menu items and to make

adjustments.

Use this button to turn on and off the Monitor.

• When no menu is displayed, you can use the 2 / 3

buttons to adjust the volume level.

4 MENU button

Use this button to display or erase menus.

While a sub-menu is displayed, pressing this button will

move you one screen back to the preceding menu.

Parts Identification

(Continued)

Monitor: Rear Views

(RS232C)

(120/230V)

SPEAKER OUT

(JVC CODE)

OUT

INTERNAL EXTERNAL

1 AUDIO output terminal (pin jack) (page 12)

Connect these terminals to the audio input terminals of

external equipment such as an amplifier.

5 SPEAKER OUT terminals (page 12)

Connect external speakers.

6 INTERNAL/EXTERNAL (built-in speaker/external

speaker) selecting sw itch (page 12)

2 REMOTE 1 (RS232C) terminal (D-sub, 9-pin) (page 12)

Connect this terminal to the RS-232C terminal of a

personal computer.

INTERNAL: To use built-in speakers.

EXTERNAL: To use external speakers.

• For the control method using this terminal, consult an

authorized JVC dealer.

7 REMOTE 2 (JVC CODE) terminals (mini jack) (page 31)

• IN

3 AC INPUT terminal (page 12)

For Master Monitor: Connect a wired remote control to

this terminal for serial connection.

Connect the supplied power cord to this terminal.

For Slave Monitors: Connect to the REMOTE 2 OUT

terminal of another Monitor in serial connection.

4 MAIN POWER sw itch (page 14)

Setting this switch to ON will put the Monitor into

standby mode, allowing you to turn on and off the power

using the POWER button either on the remote control or

on the Monitor.

• OUT

Connect to the REMOTE 2 IN terminal of another

Monitor for serial connection.

8 RGB B input/output terminals (page 12)

9 RGB A input terminal (D-sub, 15-pin) (page 12)

Connect this terminal to the video output terminal of a

personal computer.

• R, G, B, HD/Cs, VD input terminals (BNC)

Connect these terminals to the following output

terminals of a personal computer or other equipment:

– Analog RGB signal output terminals

p AUDIO input terminals (pin jack)

Connect these terminals to the audio output terminals of a

personal computer or other equipment which is also

connected to the RGB A or RGB B input terminals.

– Horizontal sync (HD) signal or composite (Cs) signal

output terminal

– Vertical sync (VD) signal output terminal

Notes:

• External sync signals are automatically detected when

they come in.

• When both horizontal (HD)/ vertical (VD) sync and

composite (Cs) sync are connected, HD/ VD sync signals

will be used.

• R, G, B, HD/Cs, VD output terminals (BNC)

Connect these terminals to the following input terminals

of another monitor:

– Analog RGB signal input terminals

– Horizontal sync (HD) signal or composite (Cs) signal

input terminal

– Vertical sync (VD) signal input terminal

Parts Identification

(Continued)

q VIDEO A terminals (page 13)*

Note:

• When both the video and S-video terminals are

connected, the S-video terminal will have priority.

• Video input terminal (BNC)

Connect this terminal to the video output terminal of a

VCR, etc.

e COMPONENT input terminals (page 13)*

• Video output terminal (BNC)

Connect this terminal to the video input terminal of

another Monitor.

• Y, P^B/B-Y, PR/R-Y input terminals (BNC)

Connect these terminals to the component signal output

terminals of NTSC or high-vision equipment.

• Audio input terminals (pin jack)

Connect these terminals to the audio input terminals of a

VCR, etc.

• Audio input terminals (pin jack)

Connect these terminals to the audio output terminals of

the other equipment.

Note:

• Since the video output terminal on this Monitor is loop-

though terminals, the devices connected to this video

output terminal should be correctly terminated.

Otherwise, pictures become abnormally bright.

w VIDEO B terminals (page 13)*

• Y/C (S video) input terminal (Y/C terminal)

Connect this terminal to the S-video output terminal of a

VCR, etc.

Note:

* GD-V4210PCE, GD-V4210PCE-G, and GD-V4211PCE do

not have the following input terminals – VIDEO A,

VIDEO B, and COMPONENT. To input video, S-video,

and component signals, you need to install video

interface kit (IF-C421P1W), which is separately

purchased.

• Video input terminal (pin jack)

Connect this terminal to the video output terminal of a

VCR, etc.

• Audio input terminals (pin jack)

Connect these terminals to the audio output terminals of

a VCR, etc.

Preparations

Checking the Accessories

The following accessories are included with the Monitor. Check for them. If any item is missing, please contact the dealer where

you purchased the Monitor.

• Remote control (RM-C575) x 1

• Remote control cable x 1

• Power cord x 3 (Use the one matching the wall outlet.)

• Batteries (AA/ R6P) x 2

Installing the Batteries

Put the batteries in the remote control as follows. If the remote control has become erratic in operation, change the batteries.

1 Remove the back cover.

While pushing the release lever on the cover, remove the cover in

the direction of the arrow.

2 Place the batteries.

Put the two supplied batteries (AA/ R6P), noting the ª and ·

markings, as shown.

3 Replace the back cover as illustrated.

Make sure the release lever on the cover is locked in place correctly.

Precautions for using batteries

If batteries are used improperly, the liquid could leak out, causing a fire, injury, etc. or dirtying the vicinity.

Take notice of the following:

• Do not mix old and new batteries.

• Do not mix different types of battery as different types may have different characteristics.

• Place the batteries according to the ª and · markings indicated on the battery compartment.

• When installing the batteries, insert the · end first to avoid a short circuit.

• Use only the specified batteries.

• When you are not using the remote control for a long time, remove the batteries.

• When the batteries have reached the end of their life, replace them with new ones immediately. Otherwise, the liquid may leak

out, or malfunction may be caused by the leaked liquid. If the leaked liquid contacts your skin, wipe off the liquid with a soft

cloth. If the affected skin is left as is, you may get a rough skin.

• Do not throw the batteries into fire or try recharging them.

• The service life of batteries is six months to one year for normal use. The supplied batteries are only for checking the operation

and their life may be shorter. When the remote control operation becomes erratic, replace with new batteries.

The instruction below applies only to

the use in Holland.

Gebruike batterijen:

Installation

Precautions

• When mounting the Monitor vertically, it is necessary to adjust the cooling fan speed to provide better heat

dissipation. Do not forget to perform this adjustment. (See page 27.)

• When installing the Monitor, be sure to use a dedicated Stand Unit, Wall Mounting Unit, or Monitor Hanger Unit, depending

on a particular case. Ask your dealer for installation.

• When installing the Monitor, refer also to the user manual for each option to use. Do not tilt the Monitor rightward, leftward,

or backward.

• Route the power cord and connection cables along wall or floor corners to avoid walking on them.

• For good heat dissipation, try to leave the following distances of space (minimum) around the Monitor.

• The ambient temperature of the installation place should be within the range of 0˚C to 40˚C.

• When installing the Monitor in a place, such as near the ceiling, the remote control may not work correctly because of possible

effects from the surroundings. If this happens, use the remote control as a wired remote control or move the Monitor where it

is free from these effects.

When installing the Monitor on a stand

Front View

Side View

200 (7⁷

(2)

150

¹⁵/16

(4 )

Wall

¹⁵/16

)

MENU INPUT

POWER

(2)

Unit: mm (inch)

Take measures against the Monitor from overturning:

To protect against abnormal events such as earthquakes and to prevent unexpected accidents, take appropriate measures

for preventing the Monitor from overturning; should it overturn, this could lead to personal injury.

For detailed information, refer to the manual supplied for the stand.

When mounting the Monitor on the wall

When hanging the Monitor from the ceiling

Front View

Side View

200

200 (7⁷

)

100

(3¹⁵/¹⁶)

100

(3¹⁵/¹⁶)

(2)

MENU INPUT

POWER

100 (3¹⁵

)

Unit: mm (inch)

/16

Unit: mm (inch)

Notes:

• Do not allow the same image (pattern) to be continuously displayed on the screen for a long time; otherwise, the area on the

screen corresponding to the image may vary in brightness, leaving an afterimage on the screen. To reduce the afterimage, you

can use the Refresh function (see page 29).

• The Monitor is manufactured using very high-precision technology, allowing for more than 99.99% active pixels, however, be

aware that only a slight number of pixels may be deficient or lit at all times.

• Do not install the Monitor in such a way that the Monitor and other AV equipment affect each other adversely. (For example,

if a disturbed image or noise due to electromagnetic interference occurs, or if the infrared remote control malfunctions, change

the installation place.)

Connections

Precautions

• Before making connections, turn off all the equipment.

• Plugs should be firmly inserted; poor connection could cause noise.

• To unplug a cord, be sure to grasp its plug and pull it out.

• Connect the power cord after having finished all other connections.

• Refer also to the user manual of each piece of equipment.

Available Signals

Video signals

The following signals can be input to this Monitor:

• VIDEO A and VIDEO B terminals accept — PAL, NTSC, NTSC4.43, and SECAM signals.

• COMPONENT terminals accept — 480i, 576i, 480p, 720p, and 1080i (1035i) signals.

(For GD-V4210PCE, GD-V4210PCE-G, and GD-V4211PCE, to input the above signals, you need to install the video interface kit

(IF-C421P1W), which is separately purchased.)

Computer signals (Preset and user-defined video modes)

This Monitor has 13 preset video modes for the most popular industrial standard (marked with ¶ in the table below), and the

signals of the following image resolutions can be input to the RGB input terminals.

For less common video modes, this Monitor can also display a picture, and memorize the video modes as user-defined video

modes (up to five modes).

When a signal other than any of the preset modes is input, it will automatically be stored as a user-defined video mode, and

when a sixth user-defined video signal is input, the first mode will be erased from memory.

Screen resolution

Horizontal

Vertical

Horizontal

Frequency (kHz) Frequency (Hz)

Vertical

Preset

setting

No.

Signal name

Scan system

PC98

640

800

1024

—

400

480

600

768

—

24.8

31.5

56.4

70.1

Non-interlace

Interlace

VGA400-70

VGA480-60

VGA480-72

VGA480-75

MAC13”

31.5

59.9

37.9

72.8

37.5

75.0

35.0

66.7

SVGA-56

SVGA-60

SVGA-72

XGA-60

35.2

56.3

37.9

60.3

48.1

72.2

48.4

60.0

–

XGA-70

56.5

70.1

RGB15K-60

RGB15K-50

User-defined

15.7

59.9

—

15.6

50.0

Interlace

—

15.0 – 16.0

16.0 – 56.0

50.0 – 75.0

Interlace

–

—

Non-interlace

Notes:

• When you are viewing XGA, setting the refresh rate (vertical scan frequency) of your personal computer to 60 Hz will enhance

the video image.

• When a signal other than listed above is input, a part of the screen may become void or an unnecessary picture may appear.

• Signals, though they are within the acceptable range of frequencies, may not be displayed normally, depending on the signal

type.

• Depending on the connected equipment, the Monitor may not be compatible with composite sync (Cs) or G on sync signals.

• When a preset mode signal is input, the vertical frequency displayed on the screen will have an “*” shown at its right top

position.

• When No. 7 to No. 11 signals are input, thin lines may happen to be hard to view on the screen, due to the internal digital

processing.

Connections

(Continued)

Connection Examples

RGB connections

When connecting another Monitor, you

can use these RGB B OUT terminals

Personal computer 1

(used as the playback source)

To R output

To R input

To audio output

To G input

To B input

To G output

To B output

When connecting the RGB

terminals, set the RGB

INPUT setting correctly (see

page 23.)

• For audio signal

connections, change the

connection when you

change the RGB INPUT

setting.

To HD/Cs input

To VD input

To HD/Cs output

To VD output

To monitor output

To audio output

Personal computer 2

(used as the playback source)

System connections

Amplifier, etc.

Personal computer

(used to control the Monitor)

To RS-232C

To audio input

To a wall outlet

Power cord (supplied)

External speakers

(RS232C)

(120/230V)

SPEAKER OUT

To speaker input

terminals

(JVC CODE)

OUT

Remote control

cable ^(supplied)

When using

external

Remote control

speakers, set this

to EXTERNAL.

INTERNAL EXTERNAL

AV connections

These terminals are not available for GD-V4210PCE, GD-V4210PCE-G, and GD-V4211PCE.

To use them, you need to install video interface kit (IF-C421P1W), which is separately purchased.

VCR 1

(used as the playback source)

VCR 2

(used as the playback source)

DVD player, etc

(used as the playback source)

Notes:

• You can connect another VCR or Monitor to the VIDEO A OUT terminal. However, when connecting a VCR

to the VIDEO A terminals, do not connect both IN and OUT terminals to the same VCR.

• When connecting a VCR to the VIDEO B terminals, you can use either the video or S-video terminals. If the

both terminals are used, S-video terminal will have priority.

Basic Operations

Daily Operations

Rear View

1 Turn on the main pow er.

Set MAIN POWER on the back of the Monitor to ON.

The POWER lamp on the upper left of the front panel

glows orange.

2 Turn on the pow er.

Press POWER on the remote control to turn the power on.

The POWER lamp changes to glow green.

• You can also use the POWER on the front panel (lower

right) to turn on the Monitor.

3 Select an input.

Select the desired input by pressing VIDEO A, VIDEO B,

COMPO. or RGB.

• You can also select the input by pressing INPUT on the

Monitor. Each time you press the button, the input

mode changes in sequence.

VIDEO A

VIDEO B

RGB A or RGB B

COMPO.

• Only for GD-V4210PCE, GD-V4210PCE-G, and

GD-V4211PCE: You can only select RGB.*

Ex. When selecting “VIDEO A” input

VIDEO

NTSC

Input selected

Input video signal

DISPLAY

Note:

DISPLAY ASPECT

POWER

RGB

• This Monitor has two RGB input terminals — RGB A and

RGB B.

When you select the RGB input, the one set on the menu

(RGB INPUT: see page 23) is selected as the input source.

If you want to select the other RGB input than the current

one, change the RGB INPUT setting on the menu.

VIDEO A VIDEO B COMPO.

MUTING

VOLUME

MUTING

MULTIPLE MONITOR ADJUSTMENT

MODE

ID SET

4 Adjust the volume.

VOLUME

–

MENU/EXIT

Notes:

• While no menu is displayed, you can adjust the volume by

pressing 2 / 3 on the Monitor.

RM-C575 REMOTE CONTROL UNIT

• When the INTERNAL/ EXTERNAL selecting switch on the

back of the Monitor is set to EXTERNAL, no sounds come

out of the built-in speakers.

When you want to hear audio sound from the built-in

speakers, set the INTERNAL/ EXTERNAL selecting switch

to INTERNAL.

To turn off the volume immediately

Press MUTING.

“MUTING ON” is displayed, and the sound goes out.

Pressing the button again resumes the previous volume level.

To make the screen indication appear

Press DISPLAY.

The types of input and signal are indicated on the screen for

about 3 seconds.

You can also make the screen indication appear using menus

(page 24).

* Only for GD-V4210PCE, GD-V4210PCE-G, and GD-V4211PCE: You need to install the video interface kit (IF-C421P1W), which

is separately purchased, to reproduce input images for VIDEO A, VIDEO B, and COMPONENT.

Changing the Aspect Ratio

With this Monitor, you can select among three types of wide

screens (FULL, ZOOM, and PANORAMIC) in addition to the

REGULAR screen of conventional 4:3 aspect ratio.

Press ASPECT to select the screen size

Each time you press the button, the screen size changes as

follows:

ASPECT

DISPLAY ASPECT

POWER

RGB

REGULAR

FULL

VIDEO A VIDEO B COMPO.

PANORAMIC

ZOOM

MUTING

VOLUME

REGULAR:

Displays at conventional 4:3 aspect ratio.

MULTIPLE MONITOR ADJUSTMENT

MODE

ID SET

MENU/EXIT

FULL:

REGULAR size display is enlarged

horizontally.

RM-C575 REMOTE CONTROL UNIT

ZOOM:

REGULAR size display is enlarged

vertically and horizontally at the same ratio.

PANORAMIC:

REGULAR size display is enlarged

horizontally to the extent that the picture

does not look abnormally.

Precautions for using the screen mode switching function

• This Monitor features a screen mode switching (aspect ratio

change) function. If you select a mode different in aspect

ratio from software such as TV programs, the picture may

look different from original picture. Be aware of this point

when you are selecting a screen mode.

• If you select a wide screen mode while viewing

conventional video programs of the aspect ratio 4:3, some

portions (edges) of the original picture will be cut off, or

deformed. To enjoy the original picture as it is, select

“REGULAR” while viewing such programs.

• If you place the Monitor in a tea room, hotel, etc. for

business purposes or public viewing and modify the picture

by using the screen mode switching (aspect ratio change)

function, this could violate the copyright protected by the

• If you make the screen very bright and watch programs

selecting “REGULAR” for a long period of time, the

Monitor screen may happen to be burned in. If this occurs,

watching programs using a wide screen mode for a while

will reduce the burn-in gradually.

Notes:

• When one of the following signals is being input, you

cannot select the aspect ratio you want.

■ 1080i, 1035i or 720p signal through the COMPONENT input

terminals

You can only select FULL.

■ 480p signal through the COMPONENT input terminals

You cannot select PANORAMIC.

■ When any signal other than RGB15K-60 and RGB15K-50

through the RGB input terminals

You can select only REGULAR and FULL.

• The aspect ratio can also be changed on the Function

Selection Menu (page 21).

Video Adjustments

For video adjustments, use menus.

You can use the buttons either on the remote control or on

Monitor for menu operations.

• Refer also to “Menu Classifications” on pages 33 and 35.

Adjusting the Picture Quality

Picture quality can be set for each input mode.

1 Press MENU/EXIT (or MENU on the

MENU INPUT

POWER

Monitor) to display the Main Menu.

MAIN MENU

PICTURE ADJ.

Cursor (3)

MENU INPUT

POWER

SIZE/POSITION ADJ.

FUNCTION SELECT

STATUS DISPLAY

ENTER:

SELECT:

EXIT: MENU

2 Press 5/∞ to move the cursor (3) to

“PICTURE ADJ.”

5 /

2 / 3

3 Press 3 to display the Picture

Adjustment Menu.

VIDEO

PICTURE ADJ.

+01

–02

CONTRAST

BRIGHT

CHROMA

PHASE

SHARPNESS

sub menu

reset

ADJUST:

SELECT:

EXIT: MENU

DISPLAY ASPECT

POWER

RGB

4 Press 5/∞ to move the cursor (3) to the

item you w ant to adjust.

VIDEO A VIDEO B COMPO.

Item

Adjustment

range

Standard

(Reset)

MUTING

VOLUME

CONTRAST

–20 to +20

+10

MULTIPLE MONITOR ADJUSTMENT

MODE

ID SET

BRIGHT (brightness) –20 to +20

CHROMA*

PHASE**

–20 to +20

2 / 3

5 /

MENU/EXIT

SHARPNESS

sub menu

MENU/EXIT

RM-C575 REMOTE CONTROL UNIT

See “To make an adjustment

while viewing the adjustment

bar” on the next page.

reset

See “To reset the adjustments” on

the next page.

* Adjustment is not possible when RGB input is selected.

** Adjustment is only possible when viewing NTSC signal

through the VIDEO A or B terminal.

5 Press 2/3 to make adjustments.

6 Press MENU/EXIT (or MENU on the

Monitor) tw ice to exit from the menu

operations.

To make an adjustment while viewing the adjustment

Adjusting the Screen Size and Position

bar

After step 3 on page 16, proceed as follows:

The screen size and position can be adjusted.

Adjusted settings can be stored for each signal type; therefore,

when the same signal comes in, the stored settings are

recalled.

• When adjusting the size, the size cannot be adjusted

proportionally, but can be enlarged rightward (or

downward) only and reduced leftward (or upward) only.

Therefore, it is necessary to adjust both the size and position

alternately to adjust to the appropriate size.

1 Press 5/∞ to move the cursor (3) to “sub menu.”

2 Press 3 to display the Sub Menu.

The Sub Menu for CONTRAST appears on the screen.

:+01

CONTRAST

–

3 Press 5/∞ to select the Sub Menu you want to adjust.

Each time you press the button, the Sub Menu changes as

follows:

1 Press MENU/EXIT (or MENU on the

CONTRAST

SHARPNESS

4 Press 2/3 to adjust the selected item.

BRIGHT

CHROMA

Monitor) to display the Main Menu.

PHASE

MAIN MENU

PICTURE ADJ.

Cursor (3)

SIZE/POSITION ADJ.

FUNCTION SELECT

STATUS DISPLAY

5 Repeat steps 3 and 4 to adjust the other items.

6 Press MENU/EXIT (or MENU on the Monitor) three times

to exit from the menu operations.

ENTER:

SELECT:

EXIT: MENU

To reset the adjustments

After step 3 on page 16, proceed as follows:

2 Press 5/∞ to move the cursor (3) to

1 Press 5/∞ to move the cursor (3) to “reset.”

2 Press 3.

The confirmation screen appears.

“SIZE/POSITION ADJ.”

3 Press 3 to display the Size/Position

reset

Are you sure?

"YES" then press

"NO" then press MENU key

Adjustment Menu.

key.

SIZE/POSITION ADJ.

3 Press 3 again to reset the adjustments.

To cancel the reset, press MENU/ EXIT (or MENU on the

Monitor).

SIZE

POSITION

SIZE

+01

–02

POSITION

CLOCK PHASE

sub menu

reset

ADJUST:

SELECT:

EXIT: MENU

4 Press 5/∞ to move the cursor (3) to the

item you w ant to adjust.

Item

Adjustment range

H (horizontal) SIZE

–80 to +80

–20 to +20

H POSITION

V (vertical) SIZE

V POSITION

CLOCK PHASE*

sub menu

reset

See “To make an adjustment

while viewing the adjustment

bar” on the next page.

See “To reset the adjustments” on

the next page.

* CLOCK PHASE can be used, while RGB input is

selected, to reduce flickering and blurring on the

screen after adjusting the screen size.

(To be continued on the next page)

Video Adjustments

(Continued)

5 Press 2/3 to adjust the selected item.

6 Press MENU/EXIT (or MENU on the

Monitor) tw ice to exit from the menu

operations.

To make an adjustment while viewing the adjustment

bar

MENU INPUT

POWER

After step 3 on page 17, proceed as follows:

1 Press 5/∞ to move the cursor (3) to “sub menu.”

2 Press 3 to display the Sub Menu.

The Sub Menu for H SIZE appears on the screen.

MENU INPUT

POWER

:+01

SIZE

3 Press 5/∞ to select the Sub Menu you want to adjust.

Each time you press the button, the Sub Menu changes as

follows:

H SIZE

CLOCK PHASE

4 Press 2/3 to adjust the selected item.

H POSITION

V SIZE

V POSITION

5 /

2 / 3

5 Repeat steps 3 and 4 to adjust the other items.

6 Press MENU/EXIT (or MENU on the Monitor) three times

to exit from the menu operations.

To reset the adjustments

After step 3 on page 17, proceed as follows:

1 Press 5/∞ to move the cursor (3) to “reset.”

2 Press 3.

The confirmation screen appears.

reset

DISPLAY ASPECT

POWER

RGB

Are you sure?

"YES" then press

"NO" then press MENU key

key.

VIDEO A VIDEO B COMPO.

MUTING

VOLUME

3 Press 3 again to reset the adjustments.

To cancel the reset, press MENU/ EXIT (or MENU on the

Monitor).

VOLUME –

MULTIPLE MONITOR ADJUSTMENT

MODE

ID SET

Note:

• Adjustment values for both horizontal and vertical sizes of

the screen are so related that if one is adjusted up to near

the maximum value, the attainable value of the other will

be decreased.

2 / 3

5 /

MENU/EXIT

RM-C575 REMOTE CONTROL UNIT

Adjusting the Color Temperature

Adjusting the White Balance

The adjusted setting applies to all inputs.

G GAIN, B GAIN and R GAIN can be finely adjusted

separately for “HIGH” and “LOW” settings of the color

temperature.

When using plural numbers of the Monitors, this can be

useful to have the same color on each screen.

1 Press MENU/EXIT (or MENU on the

Monitor) to display the Main Menu.

MAIN MENU

1 On the remote control:

PICTURE ADJ.

Cursor (3)

SIZE/POSITION ADJ.

FUNCTION SELECT

STATUS DISPLAY

Press MENU/EXIT w hile holding

VOLUME – to display the Setup Menu.

ENTER:

SELECT:

EXIT: MENU

On the Monitor:

Press MENU w hile holding 2 to display

2 Press 5/∞ to move the cursor (3) to

the Setup Menu.

“FUNCTION SELECT.”

SET-UP MENU

AUTO SLEEP

1/2

1MIN.

Cursor (3)

CONTROL LOCK

STATUS DISPLAY

VENTILATION MODE

HD SIGNAL MODE

WHITE BALANCE

1080i

3 Press 3 to display the Function

Selection Menu.

FUNCTION SELECT

“ * ” appears

ADJUST:

SELECT:

EXIT: MENU

COLOR TEMP.

PICTURE MODE

ASPECT

SIGNAL MODE

RGB INPUT

reset

HIGH

only when you

have adjusted

the White

Balance (see

the right

STILL

PANORAMA

AUTO

2 Press 5/∞ to move the cursor (3) to

“WHITE BALANCE.”

ADJUST:

SELECT:

EXIT: MENU

• The Setup Menu consists of two pages. If you keep

pressing 5/ ∞, you can move to the other page from

the current page.

column).

4 Press 5/∞ to move the cursor (3) to

“COLOR TEMP.”

3 Press 3 to display the White Balance

Adjustment Menu.

5 Press 2/3 to make an adjustment.

Each time you press the button, the color temperature

alternates between “HIGH” and “LOW.”

WHITE BALANCE:HIGH

GAIN

000

001

002

–

HIGH:

To make the screen become bluish.

To make the screen become reddish.

sub menu

reset

LOW:

ADJUST:

SELECT:

EXIT: MENU

6 Press MENU/EXIT (or MENU on the

Monitor) tw ice to exit from the menu

operations.

4 Press 5/∞ to move the cursor (3) to the

item you w ant to adjust.

Note:

• To make a fine adjustment, adjust “WHITE BALANCE” (see

the right column).

5 Press 2/3 to adjust the selected item.

6 Repeat steps 4 and 5 to adjust the other

items.

7 Press MENU/EXIT (or MENU on the

Monitor) tw ice to exit from the menu

operations.

Notes:

• Adjustable range will vary among the Monitors.

• “MAX” may appear soon after you begin adjustment. This

is normal but not a malfunction.

Video Adjustments

(Continued)

To make an adjustment while viewing the adjustment

bars

After step 3 on page 19, proceed as follows:

1 Press 5/∞ to move the cursor (3) to “sub menu.”

2 Press 3 to display the Sub Menu.

The Sub Menu for R GAIN appears on the screen.

000

GAIN

–

3 Press 5/∞ to select the Sub Menu you want to adjust.

Each time you press the button, the Sub Menu changes as

follows:

MENU INPUT

POWER

R GAIN

G GAIN

B GAIN

MENU INPUT

POWER

4 Press 2/3 to adjust the selected item.

5 Repeat steps 3 and 4 to adjust the other items.

6 Press MENU/EXIT (or MENU on the Monitor) three times

to exit from the menu operations.

To reset the adjustments

After step 3 on page 19, proceed as follows:

1 Press 5/∞ to move the cursor (3) to “reset.”

2 Press 3.

The confirmation screen appears.

5 /

2 / 3

reset

Are you sure?

"YES" then press

key.

"NO" then press MENU key

3 Press 3 again to reset the adjustments.

To cancel the reset, press MENU/ EXIT (or MENU on the

Monitor).

DISPLAY ASPECT

POWER

RGB

VIDEO A VIDEO B COMPO.

MUTING

VOLUME

MULTIPLE MONITOR ADJUSTMENT

MODE

ID SET

2 / 3

5 /

MENU/EXIT

RM-C575 REMOTE CONTROL UNIT

Changing the Picture Mode

Changing the Aspect Ratio

When one of the following signals comes in through the RGB

terminals — RGB15K-50, RGB15K-60, PC98, VGA480-60,

SVGA-56, SVGA-60, and XGA-60, you can select the picture

mode suited to either still pictures or moving pictures.

The setting adjusted applies to all inputs.

• You can change the aspect ratio by pressing ASPECT. (See

page 15.)

1 Press MENU/EXIT (or MENU on the

Monitor) to display the Main Menu.

MAIN MENU

PICTURE ADJ.

Cursor (3)

MAIN MENU

SIZE/POSITION ADJ.

FUNCTION SELECT

STATUS DISPLAY

PICTURE ADJ.

Cursor (3)

SIZE/POSITION ADJ.

FUNCTION SELECT

STATUS DISPLAY

ENTER:

SELECT:

EXIT: MENU

ENTER:

SELECT:

EXIT: MENU

2 Press 5/∞ to move the cursor (3) to

“FUNCTION SELECT.”

2 Press 5/∞ to move the cursor (3) to

“FUNCTION SELECT.”

3 Press 3 to display the Function

Selection Menu.

3 Press 3 to display the Function

Selection Menu.

FUNCTION SELECT

COLOR TEMP.

PICTURE MODE

ASPECT

SIGNAL MODE

RGB INPUT

reset

HIGH

STILL

PANORAMA

AUTO

FUNCTION SELECT

COLOR TEMP.

PICTURE MODE

ASPECT

SIGNAL MODE

RGB INPUT

reset

HIGH

STILL

PANORAMA

AUTO

ADJUST:

SELECT:

EXIT: MENU

ADJUST:

SELECT:

EXIT: MENU

* “PICTURE MODE” and “SIGNAL MODE” do not

appear at the same time.

* “PICTURE MODE” and “SIGNAL MODE” do not

appear at the same time.

“PICTURE MODE” appears when RGB input is

selected, and one of the following signals comes in —

RGB15K-50, RGB15K-60, PC98, VGA480-60, SVGA-56,

SVGA-60, and XGA-60. On the other hand, “SIGNAL

MODE” appears when VIDEO A, VIDEO B, or COMP.

(component) input is selected.

“PICTURE MODE” appears when RGB input is

selected, and one of the following signals comes in —

RGB15K-50, RGB15K-60, PC98, VGA480-60, SVGA-56,

SVGA-60, and XGA-60. On the other hand, “SIGNAL

MODE” appears when VIDEO A, VIDEO B, or COMP.

(component) input is selected.

4 Press 5/∞ to move the cursor (3) to

“ASPECT.”

4 Press 5/∞ to move the cursor (3) to

“PICTURE MODE.”

5 Press 2/3 to select an aspect ratio you

w ant.

5 Press 2/3 to select the picture mode

Each time you press the button, the aspect ratio changes

as follows:

you w ant.

REGULAR

FULL

Each time you press the button, the picture mode

alternates between “STILL” and “MOVING.”

Selects the picture quality suited to either the still picture

or the moving picture.

PANORAMIC

ZOOM

* For detailed information on these aspect ratios, see

page 15.

STILL:

When showing the still pictures mainly on the

screen.

6 Press MENU/EXIT (or MENU on the

Monitor) tw ice to exit from the menu

operations.

MOVING: When showing the moving pictures mainly on

the screen.

6 Press MENU/EXIT (or MENU on the

Monitor) tw ice to exit from the menu

operations.

Note:

• When one of the following signals is being input, you

cannot select the aspect ratio you want.

■ 1080i, 1035i or 720p signal through the COMPONENT input

terminals

You can only select FULL.

■ 480p signal through the COMPONENT input terminals

You cannot select PANORAMIC.

■ When any signal other than RGB15K-60 and RGB15K-50

through the RGB input terminals

You can select only REGULAR and FULL.

Video Adjustments

(Continued)

Setting the Receivable Signal Types

You can set the receivable signal types. Normally, select

“AUTO.”

A common setting will apply to both VIDEO A and B

terminals, and a different setting will apply to the

COMPONENT terminals.

1 Press MENU/EXIT (or MENU on the

Monitor) to display the Main Menu.

MENU INPUT

POWER

MAIN MENU

PICTURE ADJ.

Cursor (3)

SIZE/POSITION ADJ.

FUNCTION SELECT

STATUS DISPLAY

MENU INPUT

POWER

ENTER:

SELECT:

EXIT: MENU

2 Press 5/∞ to move the cursor (3) to

“FUNCTION SELECT.”

3 Press 3 to display the Function

Selection Menu.

5 /

2 / 3

FUNCTION SELECT

COLOR TEMP.

PICTURE MODE

ASPECT

SIGNAL MODE

RGB INPUT

reset

HIGH

STILL

PANORAMA

AUTO

ADJUST:

SELECT:

EXIT: MENU

* “PICTURE MODE” and “SIGNAL MODE” do not

appear at the same time.

DISPLAY ASPECT

POWER

RGB

“PICTURE MODE” appears when RGB input is

selected, and one of the following signals comes in —

RGB15K-50, RGB15K-60, PC98, VGA480-60, SVGA-56,

SVGA-60, and XGA-60. On the other hand, “SIGNAL

MODE” appears when VIDEO A, VIDEO B, or COMP.

(component) input is selected.

VIDEO A VIDEO B COMPO.

MUTING

VOLUME

MULTIPLE MONITOR ADJUSTMENT

MODE

ID SET

4 Press 5/∞ to move the cursor (3) to

“SIGNAL MODE.”

2 / 3

5 /

5 Press 2/3 to select the receivable video

MENU/EXIT

signal type.

RM-C575 REMOTE CONTROL UNIT

Each time you press the button, the receivable video

signal type changes as follows:

• When VIDEO A or VIDEO B input is selected:

AUTO

NTSC

NTSC4.43

PAL

SECAM

• When COMPONENT input is selected:

AUTO

480i

576i

1080i

720p

480p

(1035i)*

* Changes according to the “HD SIGNAL MODE”

setting (see page 27).

6 Press MENU/EXIT (or MENU on the

Monitor) tw ice to exit the menu

operations.

Setting the RGB Input

Resetting the Function Selection Menu Settings

After connecting the playback device such as a PC to the RGB

terminals, you have to specify which terminal you have

connected the device to — RGB A (D-sub 15 pin) or RGB B

(BNC) input.

• Without setting the RGB input correctly, you cannot show

any picture though you select the RGB input.

You can reset all the Function Selection Menu settings at a

time.

1 Press MENU/EXIT (or MENU on the

Monitor) to display the Main Menu.

MAIN MENU

1 Press MENU/EXIT (or MENU on the

PICTURE ADJ.

Cursor (3)

SIZE/POSITION ADJ.

FUNCTION SELECT

STATUS DISPLAY

Monitor) to display the Main Menu.

MAIN MENU

ENTER:

SELECT:

EXIT: MENU

PICTURE ADJ.

Cursor (3)

SIZE/POSITION ADJ.

FUNCTION SELECT

STATUS DISPLAY

2 Press 5/∞ to move the cursor (3) to

ENTER:

SELECT:

EXIT: MENU

“FUNCTION SELECT.”

3 Press 3 to display the Function

2 Press 5/∞ to move the cursor (3) to

Selection Menu.

“FUNCTION SELECT.”

FUNCTION SELECT

3 Press 3 to display the Function

COLOR TEMP.

PICTURE MODE

ASPECT

SIGNAL MODE

RGB INPUT

reset

HIGH

STILL

PANORAMA

AUTO

Selection Menu.

FUNCTION SELECT

ADJUST:

SELECT:

EXIT: MENU

COLOR TEMP.

PICTURE MODE

ASPECT

SIGNAL MODE

RGB INPUT

reset

HIGH

STILL

PANORAMA

AUTO

* “PICTURE MODE” and “SIGNAL MODE” do not

appear at the same time.

ADJUST:

SELECT:

EXIT: MENU

“PICTURE MODE” appears when RGB input is

selected, and one of the following signals comes in —

RGB15K-50, RGB15K-60, PC98, VGA480-60, SVGA-56,

SVGA-60, and XGA-60. On the other hand, “SIGNAL

MODE” appears when VIDEO A, VIDEO B, or COMP.

(component) input is selected.

* “PICTURE MODE” and “SIGNAL MODE” do not

appear at the same time.

“PICTURE MODE” appears when RGB input is

selected, and one of the following signals comes in —

RGB15K-50, RGB15K-60, PC98, VGA480-60, SVGA-56,

SVGA-60, and XGA-60. On the other hand, “SIGNAL

MODE” appears when VIDEO A, VIDEO B, or COMP.

(component) input is selected.

4 Press 5/∞ to move the cursor (3) to

“reset.”

5 Press 3.

4 Press 5/∞ to move the cursor (3) to

The confirmation screen appears.

“RGB INPUT.”

reset

Are you sure?

"YES" then press

"NO" then press MENU key

key.

5 Press 2/3 to select the correct RGB

terminal you use.

Each time you press the button, the RGB input alternates

between “A” and “B.”

6 Press 3 again to reset the adjustments.

When connecting the playback device to the

RGB A terminal (D-sub 15).

To cancel the reset, press MENU/ EXIT (or MENU on

the Monitor).

When connecting the playback device to the

RGB B IN terminal (BNC).

6 Press MENU/EXIT (or MENU on the

Monitor) tw ice to exit the menu

operations.

Other Convenient Functions

To set the other convenient functions, use menus.

You can use the buttons either on the remote control or on

Monitor for menu operations.

• Refer also to “Menu Classifications” on pages 33 and 35.

Showing On-screen Display

The input mode and signal type will be indicated on the

screen.

• The following procedure can be done by using the buttons

on the Monitor. You can also show these information by

pressing DISPLAY on the remote control. (See page 14.)

MENU INPUT

POWER

1 Press MENU (or MENU/EXIT on the

remote control) to display the Main

Menu.

MENU INPUT

POWER

MAIN MENU

PICTURE ADJ.

Cursor (3)

SIZE/POSITION ADJ.

FUNCTION SELECT

STATUS DISPLAY

ENTER:

SELECT:

EXIT: MENU

5 /

2 / 3

2 Press 5/∞ to move the cursor (3) to

“STATUS DISPLAY.”

3 Press 3 to display the current input

terminal and received signal type.

DISPLAY ASPECT

POWER

RGB

Ex. When selecting “VIDEO A” input

VIDEO A VIDEO B COMPO.

VIDEO

NTSC

Input selected

MUTING

VOLUME

Input Video signal

type

VOLUME –

MULTIPLE MONITOR ADJUSTMENT

Ex. When selecting “COMPONENT” input

MODE

ID SET

COMPONENT

480i

2 / 3

5 /

Ex. When selecting “RGB” input

MENU/EXIT

37.9kHz

60.3Hz*

RM-C575 REMOTE CONTROL UNIT

When the signal being input is a preset video

mode, an “*” will be shown after the

frequency.

Note:

• If you want to make these information appear automatically

when you change the input mode, see “Showing the On-

screen When Changing the Input Mode” on page 26.

Confirming the Use Time

Setting the Auto Sleep Function

You can confirm the hours of use on the Setup Menu.

This may be necessary when you ask for any service.

This function allows you to turn off (into standby mode)

automatically when no signal comes in for a certain period of

time.

1 On the remote control:

• The power lamp flashes (orange) while in the Sleep mode

(standby).

• When signals come in while in the Sleep mode, the Monitor

turns on (the power lamp glows green).

Press MENU/EXIT while holding

VOLUME – to display the Setup Menu.

On the Monitor:

1 On the remote control:

Press MENU while holding 2 to display

Press MENU/EXIT while holding

VOLUME – to display the Setup Menu.

the Setup Menu.

SET-UP MENU

AUTO SLEEP

CONTROL LOCK

STATUS DISPLAY

VENTILATION MODE

HD SIGNAL MODE

WHITE BALANCE

1/2

1MIN.

On the Monitor:

Press MENU while holding 2 to display

1080i

the Setup Menu.

ADJUST:

SELECT:

EXIT: MENU

SET-UP MENU

AUTO SLEEP

CONTROL LOCK

STATUS DISPLAY

VENTILATION MODE

HD SIGNAL MODE

WHITE BALANCE

1/2

1MIN.

Cursor (3)

2 Keep pressing 5/∞ until the second

1080i

page of the Setup Menu appears.

• The Setup Menu consists of two pages. If you keep

pressing 5/∞, you can move to the other page from

the current page.

ADJUST:

SELECT:

EXIT: MENU

2 Press 5/∞ to move the cursor (3) to

SET-UP MENU

PIXEL SHIFT

POWER SAVE

COLOR-REVERSE

REFRESH

reset

all reset

HOUR METER x1000

2/2

“AUTO SLEEP.”

• The Setup Menu consists of two pages. If you keep

pressing 5/∞, you can move to the other page from

the current page.

001

Hours of use

ADJUST:

SELECT:

EXIT: MENU

3 Press 2/3 to select the desired amount

of time.

3 Confirm the hour of use.

Select the number of minutes before the Monitor goes

into standby mode after the signal has ceased to be

supplied.

Each time you press the button, the amount of time

changes as follows:

• The displayed value for the hours of use is divided by

100. To calculate the actual hours of use, multiply the

displayed value by 100.

4 Press MENU/EXIT (or MENU on the

Monitor) once to exit from the menu

operations.

OFF

1 MIN.

2 MIN.

3 MIN.

4 MIN.

5 MIN.

To cancel the Auto Sleep function, select “OFF.”

Notes:

• The value for the hours of use is added by one hour unit. If

you use the monitor within one hour, it will not be added to

the hours of use.

• The period when the monitor is on standby (the power

lamp glows orange) will not be added to the hours of use.

4 Press MENU/EXIT (or MENU on the

Monitor) once to exit from the menu

operations.

Other Convenient Functions

(Continued)

Prohibiting the Monitor’s Button Operations

This function allows you to prohibit the button operations on

the Monitor to prevent malfunction or avoid tampering.

1 On the remote control:

Press MENU/EXIT w hile holding

VOLUME – to display the Setup Menu.

On the Monitor:

MENU INPUT

POWER

Press MENU w hile holding 2 to display

the Setup Menu.

SET-UP MENU

AUTO SLEEP

CONTROL LOCK

STATUS DISPLAY

VENTILATION MODE

HD SIGNAL MODE

WHITE BALANCE

1/2

1MIN.

Cursor (3)

MENU INPUT

POWER

1080i

ADJUST:

SELECT:

EXIT: MENU

2 Press 5/∞ to move the cursor (3) to

“CONTROL LOCK.”

5 /

2 / 3

• The Setup Menu consists of two pages. If you keep

pressing 5/ ∞, you can move to the other page from

the current page.

3 Press 2/3 to select the desired setting.

Each time you press the button, the Control Lock

function alternates between “ON” and “OFF.”

To cancel the Control Lock function, select “OFF.”

DISPLAY ASPECT

POWER

RGB

4 Press MENU/EXIT (or MENU on the

Monitor) once to exit from the menu

operations.

VIDEO A VIDEO B COMPO.

MUTING

VOLUME

Note:

VOLUME –

MENU/EXIT

• Even when the Control Lock function is in use, the

following operations are possible:

– Operation to cancel the Control Lock function

– All operations from the remote control

MULTIPLE MONITOR ADJUSTMENT

MODE

ID SET

2 / 3

5 /

MENU/EXIT

Showing the On-screen When Changing the Input Mode

RM-C575 REMOTE CONTROL UNIT

With this function, you can see the selected input mode and

signal type when changing the input mode.

1 On the remote control:

Press MENU/EXIT w hile holding

VOLUME – to display the Setup Menu.

On the Monitor:

Press MENU w hile holding 2 to display

the Setup Menu.

SET-UP MENU

AUTO SLEEP

CONTROL LOCK

STATUS DISPLAY

VENTILATION MODE

HD SIGNAL MODE

WHITE BALANCE

1/2

1MIN.

Cursor (3)

1080i

ADJUST:

SELECT:

EXIT: MENU

2 Press 5/∞ to move the cursor (3) to

Setting the High-Definition Signal Types

“STATUS DISPLAY.”

You can select one of the High-Definition (HD) signal types

through the COMPONENT terminals — 1080i or 1035i.

Normally set it to “1080i.”

• The Setup Menu consists of two pages. If you keep

pressing 5/ ∞, you can move to the other page from

the current page.

1 On the remote control:

3 Press 2/3 to select the desired setting.

Each time you press the button, the Status Display

function alternates between “ON” and “OFF.”

Press MENU/EXIT w hile holding

VOLUME – to display the Setup Menu.

To cancel the Status Display function, select “OFF.”

On the Monitor:

Press MENU w hile holding 2 to display

4 Press MENU/EXIT (or MENU on the

Monitor) once to exit from the menu

operations.

the Setup Menu.

SET-UP MENU

AUTO SLEEP

1/2

1MIN.

Cursor (3)

CONTROL LOCK

STATUS DISPLAY

VENTILATION MODE

HD SIGNAL MODE

WHITE BALANCE

1080i

Mounting the Monitor Vertically

When mounting the Monitor vertically, the temperature inside

the Monitor rises more than it is mounted horizontally. To

provide better heat dissipation, it is necessary to perform the

adjustment to switch fan speeds.

ADJUST:

SELECT:

EXIT: MENU

2 Press 5/∞ to move the cursor (3) to

“HD SIGNAL MODE.”

• The Setup Menu consists of two pages. If you keep

pressing 5/ ∞, you can move to the other page from

the current page.

1 On the remote control:

Press MENU/EXIT w hile holding

VOLUME – to display the Setup Menu.

3 Press 2/3 to select the desired setting.

Each time you press the button, the HD signal type

alternates between “1080i” and “1035i.”

On the Monitor:

Press MENU w hile holding 2 to display

the Setup Menu.

• You can select either “1080i” and “1035i” according to

the HD signal you input — whichever gives you

proportionally shaped pictures.

SET-UP MENU

AUTO SLEEP

CONTROL LOCK

STATUS DISPLAY

VENTILATION MODE

HD SIGNAL MODE

WHITE BALANCE

1/2

1MIN.

Cursor (3)

1080i

4 Press MENU/EXIT (or MENU on the

Monitor) once to exit from the menu

operations

ADJUST:

SELECT:

EXIT: MENU

2 Press 5/∞ to move the cursor (3) to

Using the Pixel Shift Function

“VENTILATION MODE.”

This function periodically shift the position (pixels) of the

displayed picture on the screen so that you can avoid the

screen from being burned in.

• The Setup Menu consists of two pages. If you keep

pressing 5/ ∞, you can move to the other page from

the current page.

1 On the remote control:

3 Press 2/3 to select “V.”

Each time you press the button, the Ventilation Mode

alternates between “H (horizontal mounting)” and “V

(vertical mounting).”

Press MENU/EXIT w hile holding

VOLUME – to display the Setup Menu.

On the Monitor:

Press MENU w hile holding 2 to display

4 Press MENU/EXIT (or MENU on the

Monitor) once to exit from the menu

operations.

the Setup Menu.

SET-UP MENU

AUTO SLEEP

1/2

1MIN.

Cursor (3)

CONTROL LOCK

STATUS DISPLAY

VENTILATION MODE

HD SIGNAL MODE

WHITE BALANCE

1080i

ADJUST:

SELECT:

EXIT: MENU

(To be continued on the next page)

Other Convenient Functions

(Continued)

2 Press 5/∞ to move the cursor (3) to

“PIXEL SHIFT” (on the second page).

• The Setup Menu consists of two pages. If you keep

pressing 5/∞, you can move to the other page from

the current page.

SET-UP MENU

PIXEL SHIFT

POWER SAVE

COLOR-REVERSE

REFRESH

2/2

reset

all reset

HOUR METER x1000

001

ADJUST:

SELECT:

EXIT: MENU

MENU INPUT

POWER

3 Press 2/3 to select the desired setting.

Each time you press the button, the Pixel Shift function

alternates between “ON” and “OFF.”

MENU INPUT

POWER

To cancel the Pixel Shift function, select “OFF.”

4 Press MENU/EXIT (or MENU on the

Monitor) once to exit from the menu

operations.

5 /

2 / 3

Using the Power Save Function

You can use this function to reduce the electrical consumption

and to extend the lifetime of the Monitor’s screen.

• The brightness of the screen will be reduced.

1 On the remote control:

Press MENU/EXIT while holding

VOLUME – to display the Setup Menu.

DISPLAY ASPECT

POWER

RGB

On the Monitor:

Press MENU while holding 2 to display

VIDEO A VIDEO B COMPO.

the Setup Menu.

MUTING

VOLUME

SET-UP MENU

AUTO SLEEP

CONTROL LOCK

STATUS DISPLAY

VENTILATION MODE

HD SIGNAL MODE

WHITE BALANCE

1/2

VOLUME –

1MIN.

Cursor (3)

MULTIPLE MONITOR ADJUSTMENT

MODE

ID SET

1080i

ADJUST:

SELECT:

EXIT: MENU

2 / 3

5 /

MENU/EXIT

2 Press 5/∞ to move the cursor (3) to

MENU/EXIT

“POWER SAVE” (on the second page).

• The Setup Menu consists of two pages. If you keep

pressing 5/∞, you can move to the other page from

the current page.

RM-C575 REMOTE CONTROL UNIT

SET-UP MENU

PIXEL SHIFT

POWER SAVE

COLOR-REVERSE

REFRESH

2/2

reset

all reset

HOUR METER x1000

001

ADJUST:

SELECT:

EXIT: MENU

3 Press 2/3 to select the desired setting.

Each time you press the button, the Power Save function

alternates between “ON” and “OFF.”

To cancel the Power Save function, select “OFF.”

4 Press MENU/EXIT (or MENU on the

Monitor) once to exit from the menu

operations.

Preventing the Afterimage Effect

2 Press 5/∞ to move the cursor (3) to

“REFRESH” (on the second page).

• The Setup Menu consists of two pages. If you keep

pressing 5/ ∞, you can move to the other page from

the current page.

After showing the same still picture on the screen, reverse the

color on the screen using this function so that you can avoid

the screen from being burned in with the still picture.

1 On the remote control:

SET-UP MENU

PIXEL SHIFT

POWER SAVE

COLOR-REVERSE

REFRESH

reset

all reset

HOUR METER x1000

2/2

Press MENU/EXIT w hile holding

VOLUME – to display the Setup Menu.

001

On the Monitor:

ADJUST:

SELECT:

EXIT: MENU

Press MENU w hile holding 2 to display

the Setup Menu.

3 Press 2/3 to select the desired setting.

The Setup Menu disappears, and the white screen appears.

SET-UP MENU

AUTO SLEEP

CONTROL LOCK

STATUS DISPLAY

VENTILATION MODE

HD SIGNAL MODE

WHITE BALANCE

1/2

1MIN.

Cursor (3)

To cancel the Refresh function

Repeat steps 1 and 2, then select “OFF” by pressing 2/ 3.

1080i

ADJUST:

SELECT:

EXIT: MENU

Resetting All the Setup Menu Settings

2 Press 5/∞ to move the cursor (3) to

You can reset all the following Setup Menu settings at a time,

except the use time of the source lamp (HOUR METER).

“COLOR-REVERSE” (on the second page).

• The Setup Menu consists of two pages. If you keep

pressing 5/ ∞, you can move to the other page from

the current page.

1 On the remote control:

Press MENU/EXIT w hile holding

VOLUME – to display the Setup Menu.

SET-UP MENU

PIXEL SHIFT

2/2

POWER SAVE

COLOR-REVERSE

REFRESH

reset

all reset

HOUR METER x1000

On the Monitor:

001

Press MENU w hile holding 2 to display

ADJUST:

SELECT:

EXIT: MENU

the Setup Menu.

SET-UP MENU

AUTO SLEEP

CONTROL LOCK

STATUS DISPLAY

VENTILATION MODE

HD SIGNAL MODE

WHITE BALANCE

1/2

3 Press 2/3 to select “ON” w hile

show ing the still picture so that you can

avoid the screen from being burned in

w ith the still picture.

1MIN.

Cursor (3)

1080i

ADJUST:

SELECT:

EXIT: MENU

Each time you press the button, the Color-Reverse

function alternates between “ON” and “OFF.”

To cancel the Color-Reverse function, select “OFF.”

2 Press 5/∞ to move the cursor (3) to

“reset” (on the second page).

• The Setup Menu consists of two pages. If you keep

pressing 5/ ∞, you can move to the other page from

the current page.

4 Press MENU/EXIT (or MENU on the Monitor)

once to exit from the menu operations.

SET-UP MENU

PIXEL SHIFT

POWER SAVE

COLOR-REVERSE

REFRESH

reset

all reset

HOUR METER x1000

2/2

Refreshing the Screen

After the power is turned off, a whitish image may be left on

the screen. In that case, leave the monitor in a white back state

for a while, and the image will disappear.

001

ADJUST:

SELECT:

EXIT: MENU

1 On the remote control:

Press MENU/EXIT w hile holding

VOLUME – to display the Setup Menu.

3 Press 3.

The confirmation screen appears.

reset

On the Monitor:

Are you sure?

"YES" then press

"NO" then press MENU key

key.

Press MENU w hile holding 2 to display

the Setup Menu.

4 Press 3 again to reset all the Setup

SET-UP MENU

AUTO SLEEP

CONTROL LOCK

STATUS DISPLAY

VENTILATION MODE

HD SIGNAL MODE

WHITE BALANCE

1/2

Menu settings.

1MIN.

Cursor (3)

To cancel the reset, press MENU/ EXIT (or MENU on

1080i

the Monitor).

ADJUST:

SELECT:

EXIT: MENU

Other Convenient Functions

(Continued)

Resetting All the Menu Settings

You can reset all the Menu settings and adjustments at a time,

except the use time of the source lamp (HOUR METER).

1 On the remote control:

Press MENU/EXIT w hile holding

VOLUME – to display the Setup Menu.

On the Monitor:

MENU INPUT

POWER

Press MENU w hile holding 2 to display

the Setup Menu.

SET-UP MENU

AUTO SLEEP

CONTROL LOCK

STATUS DISPLAY

VENTILATION MODE

HD SIGNAL MODE

WHITE BALANCE

1/2

MENU INPUT

POWER

1MIN.

Cursor (3)

1080i

ADJUST:

SELECT:

EXIT: MENU

2 Press 5/∞ to move the cursor (3) to “all

reset” (on the second page).

• The Setup Menu consists of two pages. If you keep

pressing 5/ ∞, you can move to the other page from

the current page.

5 /

2 / 3

SET-UP MENU

PIXEL SHIFT

POWER SAVE

COLOR-REVERSE

REFRESH

2/2

reset

all reset

HOUR METER x1000

001

ADJUST:

SELECT:

EXIT: MENU

DISPLAY ASPECT

POWER

RGB

3 Press 3.

VIDEO A VIDEO B COMPO.

The confirmation screen appears.

MUTING

VOLUME

all reset

Are you sure?

"YES" then press

"NO" then press MENU key

VOLUME –

key.

MULTIPLE MONITOR ADJUSTMENT

MODE

ID SET

4 Press 3 again to reset all the Menu

settings and adjustments.

To cancel the reset, press MENU/ EXIT (or MENU on

the Monitor).

2 / 3

5 /

MENU/EXIT

RM-C575 REMOTE CONTROL UNIT

Serial Connections and Operations

When the Monitors are serially connected, you can control all of them at the same time (simultaneous operation) or control them

one by one separately (individual operation).

For individual operation, you have to assign an ID number to each of the Monitors.

For the purpose of explanation, we will call Monitor 1 as a Master and Monitor 2 and subsequent Monitors as Slaves.

Connecting the Remote Control Cables

Monitor 1

(Master)

Monitor 2

(Slave)

Monitor 3

(Slave)

Monitor XX

(Slave)

Remote control

(RS232C)

(120/230V)

(RS232C)

(120/230V)

(RS232C)

(120/230V)

(RS232C)

(120/230V)

SPEAKER OUT

(JVC CODE)

OUT

Remote control

cable (supplied)

INTERNAL EXTERNAL

Remote control cable

(supplied with

Monitor 2)

Remote control cable

(supplied with

Monitor 1)

Remote control cable

(supplied with

Monitor 3)

Notes:

• Do not connect the last monitor to Monitor 1.

• When operating with a wired remote control, connect it to the REMOTE 2 (JVC CODE) input terminal of Monitor 1.

• When Monitors are serially connected, Monitor 2 and subsequent Monitors cannot be directly controlled with a wireless

remote control.

• Even after the Monitors are serially connected, each of them can be operated using the buttons on the Monitor. However,

you cannot perform simultaneous or individual operation even with the buttons on Master Monitor.

• When performing simultaneous or individual operation,

use the remote control.

Assigning ID Numbers

The following procedure should be performed slowly and

securely.

1 Turn on all the connected Monitors.

2 Press MODE.

DISPLAY ASPECT

POWER

RGB

Master

Slave 1

Slave 2

Slave XX

VIDEO A VIDEO B COMPO.

[00]

MASTER

MUTING

VOLUME

On Master Monitor screen, “MASTER” is displayed, and

“[00]” is displayed on all of Slave Monitor screens.

MULTIPLE MONITOR ADJUSTMENT

MODE

ID SET

ID +/–

MODE

ID SET

3 Press ID SET.

Master

Slave 1

Slave 2

Slave XX

[01]

[02]

[XX]

MASTER

2 / 3

5 /

MENU/EXIT

RM-C575 REMOTE CONTROL UNIT

On the Slave Monitor screens, “[01]”, “[02]”, “[03]”, ——

and so on will be displayed in the order of connection.

Notes:

• When a maximum number of 20 Monitors are connected, it

will take approx. 10 seconds for ID numbers to be displayed

on all the screens.

• If “[00]” is displayed on all the Monitor screens or if some

of the Monitors have no indication in step 1, press MODE to

turn off the indications on all Monitor screens, and then

press MODE again.

Serial Connections and Operations

(Continued)

5 Press 2/3 to make an adjustment.

At this time, if the Monitors have different

“CONTRAST” settings, the adjustment is made, based

on the different settings.

• When performing simultaneous or individual operation,

use the remote control.

VIDEO

PICTURE ADJ.

CONTRAST

BRIGHT

CHROMA

PHASE

SHARPNESS

sub menu

reset

–01

–02

CONTRAST

BRIGHT

CHROMA

PHASE

SHARPNESS

sub menu

reset

+01

–02

DISPLAY ASPECT

POWER

RGB

ADJUST:

SELECT:

EXIT: MENU

ADJUST:

SELECT:

EXIT: MENU

VIDEO A VIDEO B COMPO.

When pressing 3 once

MUTING

VOLUME

VIDEO

MULTIPLE MONITOR ADJUSTMENT

PICTURE ADJ.

MODE

ID SET

CONTRAST

BRIGHT

CHROMA

PHASE

SHARPNESS

sub menu

reset

–02

CONTRAST

BRIGHT

CHROMA

PHASE

SHARPNESS

sub menu

reset

+02

–02

ID +/–

MODE

ADJUST:

SELECT:

EXIT: MENU

ADJUST:

SELECT:

EXIT: MENU

2 / 3

5 /

MENU/EXIT

6 Press MENU/EXIT tw ice to exit from the

RM-C575 REMOTE CONTROL UNIT

menu operations.

Operating the Monitors Individually

The following procedure should be performed slowly and

securely.

1 Press MODE to display the ID numbers

on all the connected Monitors’ screens.

Master

Slave 1

Slave 2

Slave XX

[00]

MASTER

Operating the Monitors Simultaneously

• Check that no ID number is shown on the screens. If any ID

numbers are shown, press MODE to erase them.

• The following procedure should be performed slowly and

securely.

2 Press ID +/– to select the Monitor you

w ant to operate.

Example: When adjusting “CONTRAST”:

Example: To select “[02]”:

Press ID + twice.

Slave 2’s ID number “[02]” is highlighted.

* The selected ID number will be also shown on the

1 Press MENU/EXIT to display the Main

Menu.

Master Monitor (in this example, “MASTER\[02]”).

The Main Menus appear on all the connected Monitors’

screens.

Master

Slave 1

Slave 2

Slave XX

[01]

[02]

[XX]

MASTER\[02]

2 Press 5/∞ to move the cursor (3) to

“PICTURE ADJ.”

3 Perform any desired operations, such as

3 Press 3 to display the Picture

adjusting menu items.

Adjustment Menu.

The Picture Adjustment Menus appear on all the

connected Monitors’ screens.

Notes:

• If “[00]” is displayed on all the Monitor screens or if some of

the Monitor screens have no indication in step 1, press

MODE to turn off the indications on all screens, and then

press MODE again.

• If the ID number of the Monitor selected in step 2 is not

highlighted or if the ID numbers of more than one Monitor

are highlighted, press MODE to clear the ID numbers, and

then start the procedure again from the beginning.

4 Press 5/∞ to move the cursor (3) to

“CONTRAST.”

Menu Classifications

Main Menu

Picture Adjustment Menu

Main Menu

:+01

CONTRAST

–

VIDEO

MAIN MENU

PICTURE ADJ.

:+01

BRIGHT

–

+01

–02

CONTRAST

BRIGHT

CHROMA

PHASE

SHARPNESS

sub menu

reset

PICTURE ADJ.

SIZE/POSITION ADJ.

FUNCTION SELECT

STATUS DISPLAY

:+01

CHROMA

–

:+01

PHASE

–

ADJUST:

SELECT:

EXIT: MENU

ENTER:

SELECT:

EXIT: MENU

:+01

SHARPNESS

–

Adjustable only when

NTSC signals come in.

reset

Are you sure?

"YES" then press

key.

"NO" then press MENU key

Size/Position Adjustment Menu

:+01

SIZE

SIZE/POSITION ADJ.

SIZE

POSITION

SIZE

+01

–02

:+01

POSITION

+ +

POSITION

CLOCK PHASE

sub menu

reset

:+01

SIZE

ADJUST:

SELECT:

EXIT: MENU

:+01

POSITION

:+01

CLOCK PHASE

–

Appears only when

RGB input is selected.

reset

Are you sure?

"YES" then press

key.

"NO" then press MENU key

Appears only when one of

the following preset RGB signals

comes in — RGB15K-50,

Function Selection Menu

RGB15K-60, PC98, VGA480-60,

SVGA-56, SVGA-60, and XGA-60.

(See page 11 for preset signals.)

FUNCTION SELECT

COLOR TEMP.

PICTURE MODE

ASPECT

SIGNAL MODE

RGB INPUT

reset

HIGH

STILL

PANORAMA

AUTO

reset

Are you sure?

"YES" then press

"NO" then press MENU key

key.

ADJUST:

SELECT:

EXIT: MENU

Appears only when VIDEO A,

VIDEO B, or COMP. (component)

input is selected.

Status Display

VIDEO

NTSC

Input currently selected

Input video signal

Ex. When “VIDEO A” input

is selected

Menu Classifications

(Continued)

PICTURE ADJ. (Picture adjustment): See page 16.

CONTRAST

BRIGHT

CHROMA***

PHASE*

Adjusts the contrast of the picture.

Adjusts the brightness of the picture.

Adjusts the color density of the picture.

Adjusts the color phase.

SHARPNESS

sub menu

reset

Adjusts the outlines of the picture.

Displays the fine adjustment bar.

Resets the Picture Adjustment Menu settings to defaults.

SIZE/ POSITION ADJ. : See page 17.

H.SIZE

Adjusts the horizontal screen size.

H. POSITION

V. SIZE

Adjusts the horizontal screen position.

Adjusts the vertical screen size.

V.POSITION

Adjusts the vertical screen position.

CLOCK PHASE** Adjusts to eliminate stripes or flickering.

Normally, no adjustment is needed.

sub menu

reset

Displays the fine adjustment bar.

Resets Size/ position Adjustment Menu settings to defaults.

FUNCTION SELECT: See pages 19 to 23.

COLOR TEMP. Adjusts the color temperature.

Use when the picture is reddish or bluish.

PICTURE MODE**** Selects the picture quality suited to either the still picture or the moving picture.

ASPECT Selects the horizontal to vertical ratio of the screen.

SIGNAL MODE*** • Selects a color system (NTSC, NTSC 4.43, PAL, SECAM) when VIDEO A or VIDEO B input is

selected.

• Selects a scan system — 480i, 576i, 480p, 720p, 1080i (1035i) — when COMPONENT input is

selected. Normally, set to “AUTO.”

RGB INPUT

reset

Sets the correct RGB terminal you use.

Resets the Function Selection Menu settings to defaults.

Adjustment is not possible when RGB input is selected.

** Adjustment is only possible when viewing NTSC signal through the VIDEO A or B terminal.

*** Adjustment is only possible when RGB input is selected.

****Adjustment is only possible when the RGB15K-50, RGB15K-60, PC98, VGA480-60, SVGA-56, SVGA-60, or XGA-60 signals

come in.

Setup Menu

White Balance Adjustment Menu

SET-UP MENU

1/2

000

GAIN

–

AUTO SLEEP

1MIN.

WHITE BALANCE:HIGH

CONTROL LOCK

STATUS DISPLAY

VENTILATION MODE

HD SIGNAL MODE

WHITE BALANCE

GAIN

000

001

002

:+001

GAIN

–

1080i

–

sub menu

reset

:–002

GAIN

–

ADJUST:

SELECT:

EXIT: MENU

ADJUST:

SELECT:

EXIT: MENU

reset

Are you sure?

"YES" then press

key.

"NO" then press MENU key

reset

Are you sure?

"YES" then press

"NO" then press MENU key

SET-UP MENU

2/2

key.

PIXEL SHIFT

POWER SAVE

COLOR-REVERSE

REFRESH

reset

all reset

HOUR METER x1000

all reset

001

Are you sure?

"YES" then press

key.

"NO" then press MENU key

ADJUST:

SELECT:

EXIT: MENU

AUTO SLEEP

Sets the length of time before standby mode is automatically assumed after the input signal has

stopped being supplied. (See page 25.)

CONTROL LOCK

STATUS DISPLAY

Sets the Monitor so that it cannot be operated with the buttons on itself. (See page 26.)

Sets if you want the input terminal and the type of signal to be indicated on the screen just after

inputs are switched. (See page 26.)

VENTILATION MODE

HD SIGNAL MODE

WHITE BALANCE

Adjusts the cooling fan speed according to the Monitor mounting method. (See page 27.)

Select the High-Definition (HD) signal type. (See page 27.)

Adjusts R GAIN, G GAIN and B GAIN finely each for “HIGH” and “LOW” settings of the color

temperature. (See page 19.)

PIXEL SHIFT

Sets a screen saver. (See page 27.)

POWER SAVE

COLOR-REVERSE

Sets the power save function. (See page 28.)

Use to reverse the color of the still picture to prevent its afterimage from being left on the screen.

(See page 29.)

REFRESH

reset

all reset

Use to eliminate afterimages on the screen. (See page 29.)

Resets the Setup Menu settings to defaults. (See page 29.)

Resets the all menu settings and adjustments to defaults. (See page 30.)

Use to confirm the hours of use. (See page 25.)

HOUR METER

Troubleshooting

Solutions to common problems related to the Monitor are described here. If none of the solutions presented here solves the

problem, unplug the Monitor and consult an authorized dealer or service center.

Symptom

Probable cause

Corrective action

Page

Power is not supplied. • Is the power cord disconnected?

• Insert the power cord (plug) firmly.

• Is the MAIN POWER switch turned on? • Turn on the MAIN POWER switch.

Video image does not • Is the correct input selected?

appear, or audio

sound does not occur.

• Select the correct input by pressing

VIDEO A, VIDEO B, COMPO. and

RGB on the remote control (or INPUT

on the Monitor).

• Are the devices connected correctly?

• Connect the devices correctly.

12, 13

—

• Are signals being supplied from the

connected devices?

• Set the devices correctly.

• Is RGB INPUT set correctly if using the • Set it correctly.

RGB terminals?

• Are input signals (scanning frequency, • Check if the signal is appropriate

etc.) appropriate?

(scanning frequency, etc.), and input

the appropriate signal.

• Is brightness adjusted correctly?

• Is volume set at minimum?

• Adjust brightness on the menu.

• Adjust volume.

• Are the diagnostic lamps turned on?

• Refer to “Self-diagnostic indication,”

and take an appropriate action.

The picture becomes • Is the signal RGB input?

• Adjust CLOCK PHASE using the

menu.

blurred.

Colour is abnormally • Is brightness adjusted correctly?

dark or bright.

• Adjust BRIGHT (brightness) using the

menu.

Colour is poor or

unstable.

• Is picture quality (colour density, etc.) • Adjust PICTURE using the menu.

adjusted correctly?

• Is the correct broadcast system (colour • Set SIGNAL MODE (colour system) to

system) selected?

“AUTO.”

• Are signals (scanning frequency, etc.) to • Check if the signal is appropriate

connected devices appropriate?

(scanning frequency, etc.), and input

the appropriate signal.

The picture is cut or

shifted toward one

side.

• Is the size or position of the screen

adjusted properly?

• Adjust H.SIZE, V.SIZE, H.POSITION

or V.POSITION using the menu.

The remote control

does not work.

• Are the batteries correctly set?

• Are the batteries exhausted?

• Insert batteries correctly, observing the

polarities (ª and ·).

• Replace with new batteries.

• Is there any object blocking the path

between the remote control and remote

sensor?

• Remove any blocking object.

—

• Is the Monitor too far away from you? • Move toward the Monitor, then operate

the remote control.

• Is the Monitor connected serially to

another Monitor (Serial Connection)?

• Only Master Monitor can be controlled

by the remote control when connected

serially.

The buttons on the

Monitor do not work.

• Is the Control Lock function in use?

• Set the Control Lock function to “OFF”

using the menu.

Self-diagnostic Indication

The screen monitor may automatically turn off and self-diagnostic lamps next to the power lamp may light or flash.

When something abnormal occurs with the Monitor, this function informs you of the condition of the Monitor with self-

diagnostic lamps, allowing for smooth service work.

If the self-diagnostic lamps glow or flash in red, use the following procedure before consulting the dealer where you purchased

the Monitor.

Remote sensor

MENU INPUT

POWER

Power lamp Self-diagnostic lamps (1 to 3)

1 Check w hich lamps are lighting or flashing.

On the Self-diagnostic Report Sheet (below), check the box next to “Lights” or “Flashes” of the corresponding lamp or

lamps.

• Depending on a particular case, only one lamp may light or flash, or all three lamps may do so.

2 Turn off the MAIN POWER sw itch on the back of the Monitor.

3 Unplug the pow er cord.

4 Call your dealer and tell w hich lamps are lighting or flashing. (Copy and fax the Self-

diagnostic Report Sheet below.)

Note:

• If you turn on the Monitor soon after turning it off (or after recovering from a brief power interruption), the self-diagnostic

lamps may light (or flash), and no image may appear on the screen. In this case, turn off the Monitor again, wait for about 10

seconds, then turn it on again. If no self-diagnostic lamps light or flash, you can operate and use the Monitor as usual.

Store name where you purchased the Monitor

Model Name:

Plasma Display Monitor

GD-V4210PZW/GD-V4210PZW-G

GD-V4210PCE/GD-V4210PCE-G

GD-V4211PCE

Self-diagnostic Report Sheet

The self-diagnostic lamps light or flash as listed on the following

table. Please give me immediate advice or service if necessary.

Self-diagnostic lamps

Your Name:

NO. Lamp position

Conditions

Telephone No.:

Address:

Upper

Middle

Lower

& Lights

& Flashes

& Lights

& Flashes

Specifications

Model name

GD-V4210PZW / GD-V4210PZW-G

GD-V4210PCE / GD-V4210PCE-G /

GD-V4211PCE

Frame color

GD-V4210PZW: Silver

GD-V4210PZW-G: Gray

GD-V4210PCE / GD-V4211PCE: Silver

GD-V4210PCE-G: Gray

Screen size

Type 42 wide format

Aspect ratio

16:9 (Wide format)

Number of pixels displayed

Number of colors displayed

853 (H) x 480 (V)

16.77 million (256 colors for each of RGB)

Effective screen size

(W x H, Diagonally)

92.1 cm x 51.8 cm (36-3/8” x 20-1/2”), 105.7 cm (41-5/8”)

Weight

35.8 kg (78.8 lbs.)

External dimensions

(W x H x D)

103.5 cm x 64.0 cm x 8.9 cm (40-3/4” x 25-1/4” x 3-5/8”)

* Excluding protruding parts

Power requirements

Rated input current

AC 120 V / AC 230 V, 50 Hz/60 Hz

3.5 A (AC 120 V) / 1.9 A (AC 230 V)

Compatible systems

VIDEO A, B input

NTSC, NTSC 4.43, PAL, SECAM

COMPONENT input

Audio power output

480i, 576i, 480p, 720p, 1080i (1035i)

INTERNAL: 2 W + 2 W (TYP at impedance 8 Ω)

EXTERNAL: 3 W + 3 W (TYP at impedance 6 Ω)

Built-in speakers

2 pcs., 4 cm x 7 cm oval-shaped, impedance 6 Ω

Operating conditions

Temperature: 0 °C to 40 °C

Relative humidity: 20 % to 80 % (non-condensation)

VIDEO A

Video input

BNC terminal x 1, 1 V(p-p), 75 Ω

Video output

Audio input

BNC terminal x 1, 1 V(p-p), 75 Ω

Pin jack terminal x 2 (L/R)

500 mV(rms), high impedance

VIDEO B

Y/C input

Y/C terminal x 1

Y: 1 V(p-p), 75 Ω

C: 0.286 V(p-p), 75 Ω (for NTSC)

C: 0.3 V(p-p), 75 Ω (for PAL/SECAM)

Video input

Audio input

Pin jack terminal x 1, 1 V(p-p), 75 Ω

Pin jack terminal x 2 (L/R)

500 mV(rms), high impedance

COMPONENT

COMPONENT input

BNC terminal x 3

Y: 1 V(p-p), 75 Ω

P^B/B-Y: 0.7 V(p-p), 75 Ω

PR/R-Y: 0.7 V(p-p), 75 Ω

Audio input

Pin jack terminal x 2 (L/R)

500 mV(rms), high impedance

Model name

GD-V4210PZW / GD-V4210PZW-G

GD-V4210PCE / GD-V4210PCE-G /

GD-V4211PCE

RGB A

RGB input

D-sub 3-row 15-pin terminal x 1,

Video signal: 0.7 V(p-p), 75 Ω

Sync signal: TTL level

RGB B

RGB input

BNC terminal x 5 (Bridge connection possible, auto termination)

Analog RGB:

R: 0.7 V(p-p), 75 Ω G: 0.7 V(p-p), 75 Ω B: 0.7 V(p-p), 75 Ω

G on sync: 1 V(p-p), 75 Ω (negative sync)

Horizontal sync/Composite sync (HD/Cs):

HD: 1 V(p-p) to 5 V(p-p), high impedance (positive/negative polarity)

Cs: 1 V(p-p) to 5 V(p-p), high impedance (positive/negative polarity)

Vertical sync (VD):

VD: 1 V(p-p) to 5 V(p-p), high impedance (positive/negative polarity)

RGB output

AUDIO

BNC terminal x 5 (Loop through output for bridge connection)

Audio input

Pin jack terminal x 2 (L/R)

500 mV(rms), high impedance (for RGB A or RGB B)

REMOTE 1 (RS232C) terminal

D-sub 9-pin terminal x 1

REMOTE 2 (JVC CODE)

IN/OUT terminals

Stereo mini jack terminal x 2

SPEAKER OUT terminal

AUDIO output terminal

Impedance 6 Ω to 16 Ω

Pin jack terminal x 2 (L/R)

Output impedance 600 Ω

*¹GD-V4210PCE, GD-V4210PCE-G, and GD-V4211PCE do not have the following input terminals – VIDEO A, VIDEO B, and

COMPONENT.

You need to install the video interface kit (IF-C421P1W), which is separately purchased, to reproduce input images for VIDEO

A, VIDEO B, and COMPONENT.

• For easy understanding, pictures and illustrations are shown by being emphasized, omitted or composed, and may be more or

less different from actual products.

• Design and specifications are subject to change without notice.

• IBM and IBM PC are registered trademarks of International Business Machines Corporation. Macintosh is registered

trademarks of Apple Computer, Inc.

All other product names mentioned herein are used for identification purposes only, and may be the trademarks or registered

trademarks of their respective companies.

Options (not supplied)

Stand Unit

TS-C420P1W, TS-C420P4W, TS-C420P5W, TS-C420P7W

TS-C420P2W, TS-C420P6W

TS-C420P3W

Wall Mounting Unit

Ceiling suspension Unit

Video Interface Kit

IF-C421P1W (Only for GD-V4210PCE , GD-V4210PCE-G, and GD-V4211PCE)

Notice on transportation

This Monitor is precision equipment and needs dedicated packing material for transportation.

Never use any packing material supplied from other than JVC or JVC-authorized dealers.

Specifications

(Continued)

Pin assignment (Specifications for terminals)

• RS-232C terminal

This is a female type connector.

• Y/C terminal

Pin number Signal name

DCD

DSR

RTS

CTS

GND (Y)

GND (C)

DTR

GND

• RGB Input Terminal

Pin number Signal name

Red

Green

Blue

N/C

GND

N/C

GND

HD/Cs

N/C

External

GND

Dimensions

940 (37¹

)

Top view

Side view

1035 (40³

)

89 (3⁵

)

Front view

997 (39³

921 (36 ³

57.5 (2

)

11 (¹

)

MENU INPUT

POWER

Unit: mm (inch)

IBM SYSTEM STORAGE DS3000 User Manual
Intel Computer Hardware PMB 601LF User Manual
KitchenAid KECC507KSS1 User Manual
Marantz Computer Hardware Portable Solid State Recorder User Manual
MicroBoards Technology CX1 1000 User Manual
Panasonic NN C2000W User Manual
Philips 33CE7538 User Manual
Philips 44PL9522 User Manual
Philips DVP3727 User Manual
Philips ID555 User Manual