JVC DT V9L3D User Manual

INSTRUCTIONS  
DT-V9L3D  
Table of Contents  
MULTI FORMAT LCD MONITOR  
Safety Precautions .............................................. 2  
IMPORTANT SAFEGUARDS ........................... 2  
Installation............................................................ 4  
To adjust the stand height ................................ 4  
Daily Operations / Connections ......................... 6  
Front panel ....................................................... 6  
Rear panel........................................................ 8  
Available signals............................................... 9  
Menu Configuration—MAIN MENU .................. 10  
Menu Configuration—SET-UP MENU............... 14  
External Control................................................. 16  
About the external control .............................. 16  
Using the MAKE/TRIGGER system ............... 16  
Using the RS-232C system............................ 17  
Troubleshooting................................................. 18  
Self-check program ........................................ 19  
Maintenance....................................................... 20  
Specifications .................................................... 21  
General........................................................... 21  
Input/output terminals..................................... 21  
Dimensions..................................................... 22  
ENGLISH  
WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS  
APPARATUS TO RAIN OR MOISTURE.  
WARNING: THIS APPARATUS MUST BE CONNECTED TO A MAINS SOCKET  
OUTLET WITH A PROTECTIVE EARTHING CONNECTION.  
CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED.  
REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE.  
EMC Supplement  
This equipment is in conformity with the provisions and protection requirements of the corresponding European  
Directives. This equipment is designed for professional video appliances and can be used in the following  
environments:  
• Controlled EMC environment (for example purpose built broadcasting or recording studio), and rural outdoors  
environment (far away from railways, transmitters, overhead power lines, etc.)  
In order to keep the best performance and ensure electromagnetic compatibility, we recommend to use cables  
not exceeding the following length:  
Cable  
Length  
Power cord  
2.0 m  
Dear Customer,  
(attached cable (H05VV-F 3 x 0.75 mm2))  
This apparatus is in conformance with the valid European directives and standards regarding electromagnetic  
compatibility and electrical safety.  
Video signal cable (coaxial cable)  
Audio signal cable (shielded cable)  
2.0 m  
1.5 m  
European representative of Victor Company of Japan, Limited is:  
JVC Technical Services Europe GmbH  
Postfach 10 05 04  
RS-232C cable (shielded cable)  
(A straight cable with a D-sub 9-pin connector)  
2.0 m  
61145 Friedberg  
Germany  
REMOTE cable (twist pair cable)  
(A straight LAN cable)  
2.0 m  
1.0 m  
Earphone cable (parallel cable)  
Information for Users on Disposal of Old Equipment  
[European Union]  
The inrush current of this apparatus is 9.098 ampere.  
This symbol indicates that the electrical and electronic equipment should not be disposed as  
general household waste at its end-of-life. Instead, the product should be handed over to the  
applicable collection point for the recycling of electrical and electronic equipment for proper  
treatment, recovery and recycling in accordance with your national legislation.  
CAUTION  
In case where the strong electromagnetic waves or magnetism are near the audio cable or the signal cable,  
the sound or the picture will contain noise. In such cases, please keep the cable away from the sources of the  
disturbance.  
By disposing of this product correctly, you will help to conserve natural resources and will  
help prevent potential negative effects on the environment and human health which could  
otherwise be caused by inappropriate waste handling of this product. For more information  
about collection point and recycling of this product, please contact your local municipal office,  
your household waste disposal service or the shop where you purchased the product.  
Penalties may be applicable for incorrect disposal of this waste, in accordance with national  
legislation.  
Attention:  
(Business users)  
This symbol  
is only valid in  
the European  
Union.  
information about the take-back of the product.  
[Other Countries outside the European Union]  
If you wish to dispose of this product, please do so in accordance with applicable national  
legislation or other rules in your country for the treatment of old electrical and electronic  
equipment.  
ENGLISH  
3
4
Installation  
• Do not rest your arm on the monitor or lean against the monitor.  
• Do not touch the LCD panel when installing the monitor.  
• Be sure to install the monitor securely to prevent the monitor from falling over, which may cause damage to the monitor  
or injury.  
CAUTION  
Higher position  
When shipped from factory, the stand is attached to the monitor.  
You can tilt the monitor from about 20° upward to about 10° downward.  
Monitor  
Stand  
• When the monitor is not  
tilted (0°), the guidelines  
align as illustrated.  
About 20°  
0°  
Guidelines  
About 10°  
CAUTION  
• Be careful not to pinch your fingers in the gap between the monitor and the stand.  
• When the stand is attached to the lower position (page 5), you cannot tilt the monitor downward.  
7 To adjust the stand height  
Attachment screws  
You can select the stand height according to your preference—higher position or lower position.  
To change the stand height, change the position of the screw hole used for attaching the stand.  
• When shipped from factory, the stand is attached to the higher position.  
• Before adjusting the stand height, set the monitor angle to 0°.  
CAUTION  
• Lay the monitor on a cloth with the LCD panel facing down to prevent the LCD panel from being damaged.  
• Depending on the type of external batteries, the stand cannot be attached or detached when the external battery is  
attached on the monitor.  
• When the stand is attached on the lower position, some types of external batteries cannot be attached to the monitor.  
Guide holes (only for attaching  
to the higher position)  
Screw holes for lower position  
Rear panel of the monitor  
Screw holes for higher position  
Lower position  
To prevent an accidental fall  
Fix the monitor to a wall by using strings.  
Attachment screws  
Fixing the monitor  
Attach the hook (not provided) to the VESA mounting holes on the rear panel (use the two 100 mm pitch holes  
on the upper side) using M4 x 10 mm screws (not provided). Bind the hooks on the rear panel of the monitor to a  
wall or a pillar using durable string.  
Stand  
Monitor  
Hook (not provided)  
Hook and screws (M4 x 10 mm)  
(not provided)  
ENGLISH  
5
6
Daily Operations / Connections  
7 Front panel  
• “NO EFFECT” is displayed when you press a button which is not available for the current input or signal format (the lamp  
lights even when the function does not actually work).  
• The items controlled by the MAKE system cannot be controlled by the buttons on the front panel (“REMOTE ON” is displayed  
and the lamps do not light).  
Tally lamp  
This lamp is controlled by the tally function of the MAKE/TRIGGER terminal.  
• This lamp can also be used as the format indicator (“FORMAT  
INDICATOR” in “FUNCTION SETTING” on page 14).  
8 DYNAMIC button/lamp  
w
button  
Adjusts the picture to be suitable for a bright place.  
• When the DYNAMIC lamp lights:  
– “BACK LIGHT” and “PICTURE SUB ADJ.are  
not displayed on the menu.  
Turns on and off (on standby) the monitor.  
• The power switches (the POWER switch and  
DC switch) are equipped on the rear panel of the  
monitor (1, 3 on page 8).  
– The setting of “BACK LIGHT” is ineffective.  
(page 10, 14)  
To turn off the monitor completely, turn off the  
POWER switch and DC switch.  
9 MARKER button/lamp  
e VOL. +/– buttons  
1 Screw holes for attaching protective filter  
(provided)  
5 MUTING button  
Displays/hides the area marker and the safety  
marker.  
• Select the size and the style of the markers in  
“MARKER” of the MAIN MENU (page 11).  
• The marker is not displayed when it is set to  
“OFF” in “MARKER.(“NOTE” on page 11)  
Adjusts the volume.  
Turns off the sound when no menu screen is  
displayed.  
To cancel the function, press the button again or  
press VOL. +/– buttons.  
r MENU button  
• Attach the protective filter by using the provided  
screws.  
• Attach the filter to the LCD panel with the frosted  
side of the filter facing outwards (when shipped  
from the factory, a protective film and a sticker  
are attached to the frosted side).  
Activates/deactivates the display of the MAIN MENU.  
(“Menu Operations” on page 7)  
t W. F. M. (Wave form monitor) button/lamp  
Displays/hides the indication of the wave form  
monitor.  
6
/
/
/
buttons  
When a menu screen is displayed  
Selects or adjusts menu items. (“Menu  
Operations” on page 7)  
When no menu screen is displayed  
Selects the audio channels of EMBEDDED AUDIO  
signals, or adjusts the volume. (“Audio Channel  
Selection” on page 7)  
• Pressing button while holding button displays  
the SET-UP MENU. (“Menu Operations” on  
page 7)  
p Input select buttons/lamps  
Selects an input.  
• Adjust the settings of the wave form monitor in  
“WAVE FORM SETTING” of the MAIN MENU  
(page 13).  
CAUTION  
VIDEO/COMPO.: VIDEO/COMPONENT terminal  
SDI 1: E. AUDIO HD/SD SDI (IN 1) terminal  
SDI 2: E. AUDIO HD/SD SDI (IN 2) terminal  
• The lamp for the selected input lights.  
• Select an appropriate setting of “VIDEO/COMPO.  
SEL.(page 10).  
• Use only the provided screws to avoid damaging the  
monitor.  
• When attaching the protective filter, do not fasten  
screws too tightly; otherwise, the protective filter may  
be damaged.  
y DC lamp  
When the DC 12 V power voltage is being lowered  
due to the battery consumption, the lamp changes  
to orange from green. When the voltage becomes  
lower than a certain level, the monitor automatically  
turns off and the lamp turns to red.  
• Make sure to turn off the POWER switch and  
DC switch on the rear panel before replacing the  
battery.  
• The length of time that the lamp lights in orange  
differs depending on the type of battery or the  
battery condition. It is recommended to replace  
the battery when the lamp turns to orange.  
2 Speaker (monaural)  
q Power lamp  
The speaker emits the same audio signal as  
emitted from the AUDIO (MONITOR OUT) OUT 1  
terminal. (9 AUDIO (MONITOR OUT) terminals”  
on page 8)  
Unlit: The monitor is completely off (both the  
POWER switch and DC switch on the rear panel  
are turned off).  
Lights in green: The monitor is on.  
Lights in orange: The monitor is off (on standby).  
Flashes in orange: The monitor is in the P. SAVE  
(power save) mode (“NO SYNC ACTION” in  
“SYNC FUNCTION” on page 13).  
7 SCR. CHK. (Screens check) button/lamp  
Displays only the selected element (R, G, B, or the  
luminance) of video signal.  
3 EARPHONE (earphones) jack (monaural)  
Connect earphones to this jack to listen to the same  
sound as produced from the speaker.  
• Each time you press this button, the screen  
changes in the following order.  
Normal screen  
Monochrome screen  
4 Picture adjustment knob  
PHASE: Adjusts the picture hue.  
Blue screen Green screen  
Red screen  
CHROMA: Adjusts the picture color density.  
BRIGHT: Adjusts the picture brightness.  
CONTRAST: Adjusts the picture contrast.  
Menu Operations  
Audio Channel Selection  
On the Information Display  
On the Status Display  
Select audio channels emitted from the speaker  
and the AUDIO (MONITOR OUT) OUT1/OUT2  
terminals, when EMBEDDED AUDIO signals  
come in to the E. AUDIO HD/SD SDI terminal (IN1  
or IN2) and SDI input (1 or 2) is selected.  
• The speaker emits the same audio signal  
emitted from the AUDIO (MONITOR OUT) OUT  
1 terminal.  
The monitor displays the information below  
depending on the settings of the menu.  
If you press the input button of the current input,  
the status of the input signal and setting of muting  
are displayed for about 3 seconds.  
• Make the setting to display/hide the status in  
“STATUS DISPLAY” of the “INFORMATION” (☞  
page 15).  
• When “STATUS DISPLAY” is set to “AUTO” or  
“ON,the status below is also displayed in the  
following cases:  
1 Display the menu.  
To display the MAIN MENU  
\
Press MENU button.  
To display the SET-UP MENU  
\
Press button while holding button.  
MAIN MENU  
• The setting is memorized for each input (SDI 1  
and SDI 2).  
– When you change the input  
– When the signal condition of the current input  
changes  
– When you turn on the monitor  
• When “STATUS DISPLAY” is set to “ON,the  
signal format will remain displayed 3 seconds  
after the status is displayed.  
1 Press or button when a menu  
Selected item  
1 Audio level meter  
is not displayed.  
• Not displayed when no signal comes in for  
the SDI inputs or “LEVEL METER ch” is set  
to “OFF.”  
Operation guide  
SET-UP MENU  
The screen for audio channel selection is  
displayed.  
• The screen for audio channel selection  
automatically disappears in about 30  
seconds after the previous operation.  
“AUDIO SETTING” and “NOTE” on page 12  
2 Signal format  
Selected item  
• Displayed when “STATUS DISPLAY” is set  
to “ON.(“INFORMATION” on page 15)  
• For the contents displayed, see “On the  
signal format” below and “Available signals”  
on page 9.  
Audio channel selection screen  
Selected item  
Operation guide  
3
Source name assigned in “CHARACTER SET.”  
• Displayed when “SOURCE ID” is set to “ON.”  
• Displayed in large letters when “STATUS  
DISPLAY” is set to “OFF” or “AUTO.”  
1 Signal format  
2 Press  
buttons to select an item,  
then press button.  
• For the contents displayed, see “On the  
signal format” below and “Available signals”  
on page 9.  
2 Press  
buttons to select the  
channel to set.  
• For some items, adjustments will be made by  
pressing  
.
“INFORMATION” on page 15  
2 Setting of “VIDEO/COMPO. SEL.”  
page 10  
3 Setting of “MUTING”  
• E.AUDIO OUT1/SP:  
AUDIO (MONITOR OUT) OUT1 terminal and  
the speaker.  
• E.AUDIO OUT2:  
AUDIO (MONITOR OUT) OUT2 terminal.  
4 Time code  
• Displayed when “TIME CODE” is set to “ON.”  
(“TIME CODE” on page 11)  
• When the input signal includes no time code,  
“TC – –:– –:– –:– –” is displayed.  
5 CRC error indication  
• Displayed only when muting is activated.  
5 MUTING button” on page 6  
3 Press  
buttons to select an  
Ex.: When “MARKER” in the MAIN  
MENU is selected  
• Displayed when “CRC ERROR” is set to  
“ON.(“INFORMATION” on page 15)  
• A red square is displayed when an error  
occurs.  
audio channel.  
On the signal format  
The following messages appear depending on the  
type of input signals and their conditions.  
Each time you press the button, the audio  
channel changes as follows:  
3 Press  
then press  
adjustments.  
buttons to select an item,  
1/2/3/4/5/6/7/8/9/10/11/12/1+2/3+4/5+6/7+8/  
9+10/11+12/1G(1–4)/2G(5–8)/3G(9–12)/  
1G+2G(1–8)/1-3G(1–12)  
buttons to make  
When no video signal comes in  
\
“NO SYNC”  
When a noncompliant video signal comes in  
“Out of range”  
\
4 Press MENU button to finish the  
4 Press MENU button.  
The screen for audio channel selection  
disappears.  
When “COLOR SYSTEM” (“FUNCTION  
menu operation.  
SETTING” on page 14) is set to “AUTO” and the  
noncompliant composite video signals come in  
• Pressing MENU button repeatedly  
deactivates the display of the menu.  
\
“OTHERS”  
ENGLISH  
7
8
Daily Operations / Connections (cont.)  
5 VIDEO/COMPONENT terminals (BNC)  
IN: Input terminals for the composite (VBS) and the  
analog component (Y/PB/PR) signals.  
• Select the signal type in “VIDEO/COMPO. SEL.”  
corresponding to the type of the input signal (☞  
page 10).  
p REMOTE terminals  
7 Rear panel  
Terminals for controlling the monitor by an external  
control. (“External Control” on page 16)  
q Carry handle  
Use this handle when carrying the monitor.  
w Security slot  
OUT: Output terminal for the composite (VBS) and  
the analog component (Y) signals.  
Attach a security wire to this slot.  
e Screw holes for external battery attachment  
Attach external battery for DC 12 V power supply  
by using 2 screw holes. Choose the appropriate  
screw holes from 1, 2, 3 or 4, according to the type  
of external battery.  
6 AUDIO IN terminal (pin jack)  
Input terminal for the analog audio signals.  
• Use this terminal for the analog audio connection  
of the SDI.  
7 E. AUDIO HD/SD SDI (SWITCHED OUT) terminal  
(BNC)  
• Use the Anton Bauer Dionic 90 (mount: QR DXC-  
M3A) external battery.  
Output terminal for the HD/SD SDI signals.  
• The SDI signals of the current input (SDI 1 or SDI  
2) are re-clocked, then emitted.  
• When an input other than SDI 1 and SDI 2 is  
selected, the SDI signal of the input selected last  
time is emitted from this terminal.  
• The signals are emitted from this terminal only  
when the monitor is on or in “P.SAVE” (power  
save) mode.  
CAUTION  
Do not use the external battery for DC 24 V  
power supply.  
• Use only the battery specified above. If a heavy  
battery is used, it may fall off depending on the  
way the monitor is used.  
1 POWER switch  
Turns AC power on or off.  
You need to press  
button (w on page 6)  
to use the monitor after turning on the POWER  
switch.  
Note for connections  
2 AC IN terminal  
8 E. AUDIO HD/SD SDI (IN 1, IN 2) terminals (BNC)  
Input terminals for the HD/SD SDI signals.  
• The terminals accept also EMBEDDED AUDIO  
signals including up to 12 audio channels with a  
sampling frequency of 48 kHz.  
AC power input connector.  
Connect the provided AC power cord to an AC  
outlet.  
• Attach the provided power cord holder to prevent  
accidental disconnection of the AC power cord (☞  
“Attaching the Power Cord Holder” on page 9).  
• Before making any connections, turn off all the  
equipment.  
• Use a cord whose plugs correctly match the  
terminals on this monitor and the equipment.  
• Plugs should be firmly inserted; poor connections  
could cause noise.  
• When unplugging a cord, be sure to grasp its plug  
and pull it out.  
• DO NOT connect the power cord until all connections  
are complete.  
9 AUDIO (MONITOR OUT) terminals (pin jack)  
Output terminals for the analog audio signal.  
• The terminals emit the audio signals coming  
in from the AUDIO IN terminal or EMBEDDED  
AUDIO signals coming in from the E. AUDIO HD/  
SD SDI (IN 1 or IN 2) input terminal. (“Audio  
Channel Selection” on page 7)  
3 DC switch  
Turns the DC 12 V power on or off.  
You need to press  
button (w on page  
6) on the front panel to turn on the monitor after  
turning on the DC switch.  
• The monitor consumes the battery even while the  
monitor is on standby. To save battery life, turn  
off the DC switch.  
• Refer also to the user manual of each piece of  
equipment.  
• The signal is output from these terminals only  
when the monitor is on or in “P.SAVE” (power  
save) mode. (“NO SYNC ACTION” in “SYNC  
FUNCTION” on page 13)  
4 DC IN terminal  
• The EMBEDDED AUDIO signal...  
DC 12 V (maximum DC 17  
– is decoded into an analog signal, then emitted.  
– is emitted only when “SDI 1” or “SDI 2” is  
selected, and when EMBEDDED AUDIO  
signals come in to the E. AUDIO HD/SD SDI  
(IN 1 or IN 2) terminal.  
V) power input connector.  
• While using both the  
AC and DC 12 V power  
supply, AC power supply  
is preferentially used. If the AC power supply is  
cut off (for example, when turning off the POWER  
switch), the power supply automatically switches  
to the DC 12 V power supply.  
CAUTION  
Do not connect the power cord until all  
other connections are completed.  
When using DC 12 V power (maximum DC 17 V),  
check the DC IN terminal pin signal, and use the  
correct polarity. If the polarity is reversed, this  
could cause a fire or personal injury.  
7 Available signals  
Attaching the Power Cord Holder  
The following signals are available for this monitor.  
The provided power cord holder prevents accidental disconnection of the AC power cord from the AC IN  
terminal.  
Video signals  
• The power cord holder consists of two parts, a case and a cover.  
Input terminal  
VIDEO/COMPONENT  
Signal format shown  
in the status display  
No.  
Signal name  
E. AUDIO HD/  
SD SDI*1  
1
3
AC IN terminal  
VBS  
Y/PB/PR  
(Analog component)  
(page 7)  
Case  
(Composite)  
1
2
3
4
5
6
7
8
9
NTSC*2  
NTSC  
PAL  
PAL  
B/W50  
B/W60*2  
PAL  
NTSC  
CAUTION  
Make sure the plug will not be pulled out after the  
cover is attached to the case.  
CAUTION  
Use only the provided screws.  
480/60i  
480/60i  
480/59.94i*2  
576/50i  
480/60p  
480/59.94p  
480/59.94i  
576/50i  
To detach the cover  
2
480/60p  
480/59.94p  
576/50p  
720/60p  
720/59.94p  
720/50p  
1080/60i  
1080/59.94i  
1080/60i  
1080/59.94i  
1080/50i  
1080/60i  
1080/50i  
1080/59.94i  
1080/24psf  
1080/23.98psf  
10 576/50p  
11 720/60p  
Cover  
12 720/59.94p  
13 720/50p  
14 1080/60i  
15 1080/59.94i  
16 1035/60i  
*3  
*4  
*3  
*5  
*4  
*3  
*4  
*3  
*5  
*4  
17 1035/59.94i  
18 1080/50i  
19 1080/30psF  
20 1080/25psF  
21 1080/29.97psF  
22 1080/24psF  
23 1080/23.98psF  
: Acceptable  
—: Not acceptable  
*1 Compatible with EMBEDDED AUDIO signals  
*2 When the number of vertical scanning lines of the incoming signal is 483, the picture is displayed with 480 lines.  
*3 The signal is recognized as 1080/60i.  
*4 The signal is recognized as 1080/59.94i.  
*5 The signal is recognized as 1080/50i.  
• Analog component signals are compatible with Y on sync signals.  
ENGLISH  
9
10  
Menu Configuration—MAIN MENU  
For the operation procedure, see page 7.  
PICTURE IMPROVEMENT  
Setting for the picture quality  
Item  
To do  
Setting value  
APERTURE*  
Select the frequency of the luminance signal compensated in  
“APERTURE LEVEL.”  
OFF, LOW, HIGH  
APERTURE  
LEVEL*  
Compensate the frequency response of the luminance signal of the  
video signal.  
01 – 10  
sub menu  
reset  
Display the sub menu which enables you to adjust the items of “PICTURE IMPROVEMENT” while  
viewing the actual picture.  
Restore the default settings for all the items in “PICTURE IMPROVEMENT.”  
Setting value: –20 – +20  
BACK LIGHT  
Adjusts the brightness of the display.  
• When the DYNAMIC lamp lights, this item does not appear on the menu (8 on page 6).  
Operation guide  
Shows the buttons for  
each operation.  
Setting value: OFF, ON  
FOCUS ASSIST  
Helps to focus the picture.  
• When “ON” is selected,  
– “PICTURE IMPROVEMENT” is not displayed on the menu.  
– The settings of “PICTURE IMPROVEMENT” are ineffective.  
• The menu automatically disappears in about 30 seconds after the previous operation.  
• Some items may not appear on the menu depending on the input or the input signal.  
• The items controlled by the MAKE system do not appear on the menu.  
Setting value: OFF, ON  
COLOR RANGE MODE  
Reduces the difference of the luminance level specific to the LCD panel.  
• When “ON” is selected, the color temperature becomes the innate temperature in the LCD panel, and the  
setting of “WHITE BALANCE SET.” becomes ineffective (page 14).  
Setting value: VIDEO, COMPO. (component)  
VIDEO/COMPO. SEL.  
Selects the signal type you want to use for the VIDEO/COMPONENT terminals.  
• When select the component (COMPO.), make sure to set the component level in “COMPO. LEVELin  
“PICTURE SUB ADJ.(page 14).  
Setting value: 4:3, 16:9  
ASPECT*  
Changes the aspect ratio of the picture.  
* Memorized for each input — composite signal input (VIDEO), component signal input (COMPO.), SDI 1 and SDI 2.  
MARKER*1  
Settings for marker functions  
1/2  
Item  
To do  
Setting value  
“NOTE”  
AREA MARKER*2  
Activate/deactivate the area marker and select the  
style of it.  
Select the aspect ratio of the area marker.  
MARKER ASPECT*2  
4:3, 14:9, 13:9, 2.35:1, 1.85:1,  
1.66:1  
SAFETY MARKER  
Activate/deactivate the safety marker and select the  
style of it.  
“NOTE”  
SAFETY AREA  
FRAME*3  
Adjust the area of the safety marker.  
Displays/hides the frame indicating the area of the  
specified aspect ratio.  
80% – 100%  
OFF, ON  
Operation guide  
Shows the buttons for each  
operation.  
CENTER MARKER  
LINE BRIGHTNESS  
Displays/hides the marker indicating the center  
position of the picture.  
Adjust the brightness of the marker.  
OFF, ON  
HIGH, LOW  
• The menu automatically disappears in about 30 seconds after the previous operation.  
• Some items may not appear on the menu depending on the input or the input signal.  
• The items controlled by the MAKE system do not appear on the menu.  
2/2  
Item  
To do  
Setting value  
“NOTE”  
R-AREA MARKER*2  
Activate/deactivate the area marker and select the  
style of it.  
R-MARKER ASPECT*2  
R-SAFETY MARKER  
R-SAFETY AREA  
Select the aspect ratio of the area marker.  
4:3, 14:9, 13:9, 2.35:1, 1.85:1,  
1.66:1  
“NOTE”  
Activate/deactivate the safety marker and select the  
style of it.  
Adjust the area of the safety marker.  
80% – 100%  
• The area marker and the safety marker is displayed by using MARKER button or external control.  
• Select either non-“R-” items or “R-” items to activate by using external control (“External Control” on page 16).  
• When a picture is displayed in 4:3 aspect ratio, the safety marker for the 4:3 area is displayed.  
To display the safety marker for the area of a picture displayed in 16:9 aspect ratio, hide the area marker.  
(“NOTE”)  
*1 Memorized for each input — composite signal input (VIDEO), component signal input (COMPO.), SDI 1 and SDI 2.  
*2 Displayed only when picture is displayed in 16:9 aspect ratio.  
*3 For signals of NTSC, B/W60, 480/60i and 480/59.94i, only the vertical borders of the frame are displayed.  
Setting value: OFF, ON  
TIME CODE  
Activates/deactivates the display of the time data (time code) contained in the SDI signal.  
(“On the Information Display” on page 7)  
NOTE  
Setting of “AREA MARKER”, “SAFETY MARKER”, “R-AREA MARKER”,  
“R-SAFETY MARKER”  
The setting values and features are as follows.  
OFF:  
Deactivate the marker.  
LINE:  
HALF:  
Displays the area with an outline.  
The area outside the specified aspect ratio of the screen is displayed at 50% transparency.  
HALF+L: The area of the specified aspect ratio of the screen is indicated by an outline, and the area  
outside of that is displayed at 50% transparency.  
BLK.:  
The area outside the specified aspect ratio of the screen is black. Only the portion of the picture  
within the designated area is displayed.  
BLK. +L: The area of the specified aspect ratio of the screen is indicated by an outline, and the area  
outside of that becomes black so that only the area inside the line is displayed.  
ENGLISH  
11  
12  
Menu Configuration—MAIN MENU (cont.)  
AUDIO SETTING  
Settings for the level meter  
Item  
To do  
Setting value  
BAR POSITION  
Select the type of the level meter display  
— vertically or horizontally.  
VERT. (vertically), HORZ. (horizontally)  
LEVEL METER ch  
CH ARRANGE  
BAR TYPE  
Select the number of the audio channels  
displayed on the level meter.  
Select the order of the audio channels  
displayed on the level meter.  
OFF, 12CH, 8CH  
LINE, DIVIDE (“NOTE”)  
Select the color of the level meter display.  
3COLORS (3 colors to indicate variations in  
input levels), W.100 (white), W.50 (half tone)  
REFERENCE LEVEL Select the standard input level indicated on the –20dB, –18dB  
Operation guide  
Shows the buttons for each  
operation.  
level meter.  
OVER LEVEL  
Select the input level’s lower limit indicated in  
red for the “3COLORS” display.  
Select the brightness of the level meter.  
–10dB, –8dB, –6dB, –4dB, –2dB  
LOW, HIGH  
BAR BRIGHTNESS  
• The menu automatically disappears in about 30 seconds after the previous operation.  
• Some items may not appear on the menu depending on the input or the input signal.  
• The items controlled by the MAKE system do not appear on the menu.  
NOTE  
Example of the level meter display—Level meter position and audio channels  
Ex.: When “LEVEL METER ch” is set to “8CH” and “BAR TYPE” is set to “3COLORS.”  
REFERENCE LEVEL  
OVER LEVEL  
REFERENCE LEVEL  
OVER LEVEL  
• When “CH ARRANGE” is set  
to “DIVIDE,odd channels are  
displayed on the left and even  
channels are displayed on the  
right.  
Green  
Green  
Red  
Red  
Yellow  
Yellow  
• When “BAR TYPE” is set  
to “W.100” or “W.50,” the  
standard input level set in  
the “REFERENCE LEVEL”  
is displayed with the line  
indication. The input level set in  
“OVER LEVELis not displayed.  
• The level meter with no signal  
input is displayed in white for  
“3COLORS,and in gray for  
“W.100” or “W.50.”  
Ex.: BAR POSITION: HORZ.,  
CH ARRANGE: LINE  
Ex.: BAR POSITION: HORZ.,  
CH ARRANGE: DIVIDE  
OVER LEVEL  
OVER LEVEL  
Red  
Yellow  
Green  
Red  
Yellow  
Green  
REFERENCE LEVEL  
REFERENCE LEVEL  
Ex.: BAR POSITION: VERT.,  
CH ARRANGE: LINE  
Ex.: BAR POSITION: VERT.,  
CH ARRANGE: DIVIDE  
WAVE FORM SETTING  
Settings for the wave form monitor  
Item  
To do  
Setting value  
POSITION  
Select the position of the wave form monitor.  
1 (lower right), 2 (lower left), 3 (upper left),  
4 (upper right)  
GAIN  
Adjust the gain level for the incoming wave form  
data.  
Select the over level for the incoming luminance  
signals.  
Activates/deactivates the function to change the  
color of a wave form when the signal exceeds the  
limit specified on “LEVEL(below).  
–10 – +10  
“NOTE”  
OFF, ON  
OVER LEVEL  
MARKING  
LEVEL  
AUTO OFF  
Adjust the lower limit for the luminance signal  
070 –109  
ON, OFF  
Activates/deactivates the function to make the  
wave form monitor indication go off automatically  
15 minutes after displaying it.  
SYNC FUNCTION  
Operation guide  
Shows the buttons for each  
operation.  
Settings for the synchronization with signals  
Item  
To do  
Setting value  
OFF,  
P.SAVE (power save mode),  
GRAY B. (gray screen)  
NO SYNC ACTION  
Select the screen status when no signal is  
coming in.  
• The menu automatically disappears in about 30 seconds after the previous operation.  
• Some items may not appear on the menu depending on the input or the input signal.  
• The items controlled by the MAKE system do not appear on the menu.  
DELAY TIME  
Select the period until the screen status  
changes as selected in “NO SYNC ACTION”  
after signals stop coming in.  
30sec., 5min., 15min.  
• When setting “NO SYNC ACTION” to “GRAY B.,” the screen color changes to gray and the power consumption  
of the back light is saved by half.  
Selecting “P.SAVE” (power save mode) saves more power consumption by turning off the back light.  
NOTE  
Example of the wave form monitor  
Ex.: When “MARKING” is set to “ON” and “LEVELis set to “080”  
White  
Red  
• The wave which goes over the value set on “LEVEL”  
is indicated in red.  
Video signal  
Start  
End  
ENGLISH  
13  
14  
Menu Configuration—SET-UP MENU  
FUNCTION SETTING  
For the operation procedure, see page 7.  
Settings for the sub menu display, color system, color of the tally lamp, and the format indicator.  
Item  
To do  
Setting value  
“NOTE”  
sub menu POSI. Select the contents and displaying position of “sub menu.”  
COLOR  
SYSTEM  
Select the color system.  
• If the picture is unstable with “AUTO,select “NTSC” or “PAL.”  
AUTO, NTSC, PAL  
TALLY SELECT Select the color of the tally lamp.  
GREEN, RED  
FORMAT  
INDICATOR  
Select whether to use the tally lamp as the format indicator.  
OFF, ON (“NOTE”)  
• When “FORMAT INDICATOR” is set to “ON,” the TALLY function of the MAKE/TRIGGER terminal is not  
available.  
PICTURE SUB ADJ.  
Adjusts the standard level for the picture adjustment and selects the set-up level for the input video signal.  
Item  
To do  
Setting value  
–20 – +20  
Operation guide  
Shows the buttons for  
each operation.  
CONTRAST*1 Adjust the standard level for the contrast  
adjusted with CONTRAST knob on the front  
panel.  
BRIGHT*1  
CHROMA*1  
PHASE*1  
Adjust the standard level for the brightness  
adjusted with BRIGHT knob on the front panel.  
Adjust the standard level for the chroma adjusted –20 – +20  
with CHROMA knob on the front panel.  
Adjust the standard level for the phase adjusted  
with PHASE knob on the front panel.  
–20 – +20  
–20 – +20  
NTSC SETUP Select the set-up level of the input NTSC signal. 00 (compliant with 0% set-up signal), 7.5 (compliant  
with 7.5% set-up signal)  
COMPO.  
LEVEL  
Select the level of the analog component signal  
(480i and 576i only).  
B75 (compliant with BetacamVTR 7.5% set-up  
signal), B00 (compliant with BetacamVTR 0% set-  
up signal), SMPTE (compliant with M2VTR signals)  
• The menu automatically disappears in about 30 seconds after the  
previous operation.  
• Some items may not appear on the menu depending on the input or  
the input signal.  
sub menu  
Display the sub menu which enables you to adjust the items in “PICTURE SUB ADJ.while viewing the  
actual picture.  
Restore the default settings for all the items in “PICTURE SUB ADJ.”  
reset  
• The items controlled by the MAKE system do not appear on the menu.  
• When the DYNAMIC lamp lights, “PICTURE SUB ADJ.does not appear on the menu (8 on page 6).  
H. POSITION*1  
Setting value: –003 – +003  
Adjusts the horizontal picture position.  
NOTE  
WHITE BALANCE SET.  
Selects the color temperature and adjusts the drive level of each color (R/G/B).  
Settings of “sub menu POSI.”  
Item  
To do  
Setting value  
The setting values and features are as follows.  
COLOR TEMP.  
Select the color temperature.  
9300K, 6500K, USER  
MIN – 000 – MAX (in 256  
grades)  
LOWER1: Displays the current setting and adjustment bar at the lower part of the screen.  
UPPER1: Displays the current setting and adjustment bar at the upper part of the screen.  
LOWER2: Displays the current setting at the lower part of the screen.  
UPPER2: Displays the current setting at the upper part of the screen.  
R DRIVE, G DRIVE, Adjust the drive level of each color (red, green, and blue).  
B DRIVE*2  
sub menu  
Display the sub menu which enables you to adjust the items in “WHITE BALANCE SET.” while  
viewing the actual picture.  
reset  
Restore the default settings for the drive levels of the selected color temperature.  
• The adjustment bar is not displayed for some items.  
Color of the format indicator  
• When “COLOR RANGE MODE” is set to “ON,WHITE BALANCE SET.” does not appear on the menu (☞  
page 10).  
When “FORMAT INDICATOR” is set to “ON,” the tally lamp lights as follows according to the incoming video  
signal.  
*1 Memorized for each input — composite signal input (VIDEO), component signal input (COMPO.), SDI 1 and SDI 2.  
*2 Memorized for each color temperature.  
Lights in green: 720/60p, 720/59.94p, 720/50p, 1080/60i, 1080/59.94i, 1080/50i, 1035/60i, 1035/59.94i,  
1080/24psF, 1080/23.98psF, 1080/30psF, 1080/25psF, 1080/29.97psF  
Lights in red: 480/60i, 480/59.94i, 576/50i, 480/60p, 480/59.94p, 576/50p  
Lights in orange: composite signal  
• The lamp goes off when the non-compliant video signals are coming in.  
(“External Control” on pages 16, 17)  
REMOTE SETTING  
Settings for the external control  
Item  
To do  
Setting value  
TYPE SEL.  
Select the external control method for the MAKE/  
TRIGGER terminal.  
MAKE, TRIGGER, SET  
PIN1, PIN2, PIN3,  
PIN4, PIN5  
Assign the control functions to the pins of the MAKE/ TALLY SEL, SDI 1, SDI 2, VIDEO/  
TRIGGER terminal.  
COMPO., MARKER, FRAME,  
• Assign a function to each pin terminal by selecting C.MARKER, MARK.SEL, ASPECT,  
“SET” in “TYPE SEL.mentioned above. (The  
STATUS, L.METER, TIME CODE,  
functions are assigned for “PIN6” – “PIN8” and you SOURCE ID, WAVE FORM, COLOR  
cannot change the assignment of these functions.) OFF, SCR CHECK, DYNAMIC, FOCUS  
ASSIST, COLOR RANGE, MUTING,  
– – – (no function)  
Operation guide  
Shows the buttons for  
each operation.  
INFORMATION  
Settings for the information display of the monitor  
Item  
SOURCE ID  
To do  
Setting value  
OFF, ON  
Select if the name assigned in “CHARACTER SET.” is displayed on  
the screen (“On the Information Display” on page 7).  
CHARACTER SET.  
STATUS DISPLAY  
CRC ERROR  
Assign a name to each video source as you like (10 characters at  
maximum).You can also enter a name using the RS-232C system.  
Select if the status of the current input and the setting of muting are  
displayed on the screen (“On the Status Display” on page 7).  
Select if the CRC error indication for the input HD SDI signal is displayed ON, OFF  
“NOTE”  
AUTO, OFF, ON  
on the screen (“On the Information Display” on page 7).  
SUB HOUR METER Display the hours of use (unit: hour).You can reset this item.  
• The menu automatically disappears in about 30 seconds after the previous operation.  
• Some items may not appear on the menu depending on the input or the input signal.  
• The items controlled by the MAKE system do not appear on the menu.  
MODEL  
VERSION  
HOUR METER  
Display the model name of the monitor.  
Display the version of the monitor.  
Display the total hours of use (unit: hour). This item is used for maintenance of the monitor.  
You cannot reset this item.  
Setting value: OFF, ON  
CONTROL LOCK  
Turns on (or off) the control lock function to disable the buttons on the front panel.  
• The following operations are available even when this function is activated.  
Turning on/off (on standby) the monitor  
NOTE  
– Displaying the SET-UP MENU (by pressing button while holding button) and turning “CONTROL LOCK”  
to “OFF”  
Setting of “CHARACTER SET.”  
Assign a name for each video source.  
– Operating the monitor by an external control  
If you try other operations, “ Control lock on!” appears on the screen.  
1 Change the input to one that you want to assign a video source name for.  
You cannot store different video source names for composite signal  
input (VIDEO) and component signal input (COMPO.).  
all reset  
2 Select “CHARACTER SET.”  
Restores all the settings and adjustments of the monitor to the default.  
3 Press  
buttons to select the first character.  
• Each time you press button, the character changes as follows. Press button to reverse the order.  
• “HOUR METER” and the settings done by using the adjustment knobs on the front panel will not be reset.  
• When you operate the monitor with the AC power supply, the monitor is turned off (on standby) then turned  
on automatically. When you operate the monitor with the DC 12 V power supply, the monitor is turned off (on  
standby).  
Space  
4 Press button to move the arrow to the next space.  
• The characters entered before moving the arrow are memorized.  
5 Repeat steps 3 and 4 (10 characters at maximum).  
6 Press MENU button to store the name.  
ENGLISH  
15  
16  
External Control  
Functions controlled by the MAKE/TRIGGER system  
7 About the external control  
Display  
TALLY SEL  
SDI 1  
Functions to be controlled  
Selects the color of the tally lamp.  
Changes the input to “SDI 1.”  
Changes the input to “SDI 2.”  
Opening  
Green  
Invalid  
Invalid  
Invalid  
Off  
Short-circuiting  
This monitor has two external control terminals.  
Red  
Valid  
Valid  
Valid  
On  
MAKE/TRIGGER terminal (RJ-45): The following external control systems are available.  
(1) MAKE (make contact) system: Controls the monitor by short-circuiting the corresponding pin terminal to  
the GND pin terminal, or disconnecting (opening) it (below).  
(2) TRIGGER (trigger) system: Controls the monitor by sending the pulse signal instantaneously to the  
corresponding pin terminal (below).  
SDI 2  
VIDEO/COMPO. Changes the input to “VIDEO/COMPO.”  
MARKER  
FRAME  
C.MARKER  
MARK.SEL  
ASPECT  
The area marker and the safety marker indication  
Indication of the area of the specified aspect ratio  
The center marker indication  
Selects the items of “MARKER”*4  
Changes the aspect ratio.  
Off  
Off  
On  
On  
RS-232C terminal (D-sub 9-pin): Controls the monitor with the RS-232C system. (page 17)  
Non-“R-” items  
4:3  
“R-” items  
16:9  
“On the Status Display” on page 7  
• Control priority is as follows.  
MAKE > TRIGGER, RS-232C, buttons and menu on the monitor  
You can use the external control even when “CONTROL LOCK” is set to “ON” (page 15).  
• When the monitor is off (on standby), external control is not available.  
STATUS  
Status display*5  
6
L.METER  
Audio level meter display  
*
TIME CODE  
SOURCE ID  
WAVE FORM  
COLOR OFF  
SCR CHECK  
DYNAMIC  
Time code display  
Off  
Off  
Off  
On  
On  
On  
“SOURCE ID” on page 15  
Wave form monitor display*7  
Color off  
Screens check  
Adjusts the picture to be suitable for a bright place.  
7 Using the MAKE/TRIGGER system  
You can control the monitor by a personal computer or dedicated controller*1.  
Color  
Monochrome  
8
*1 The controller is not commercially available. Consult your dealer if you need it.  
*
Off  
Off  
On  
On  
FOCUS ASSIST Helps to focus the picture.  
The MAKE/TRIGGER terminal is configured as follows.You can assign a function to each pin terminal in  
“REMOTE SETTING” (“PIN1, PIN2, PIN3, PIN4, PIN5” on page 15).  
COLOR RANGE Reduces the difference of the luminance level specific to  
the LCD panel.  
Off  
On  
Pin No.  
Pin name  
PIN1  
PIN2  
PIN3  
PIN4  
Pin No.  
Pin name  
PIN5  
PIN6 (TALLY)*2  
PIN7 (ENABLE)*3  
PIN8 (GND)  
MUTING  
— — —  
Muting on/off  
No function  
Off  
On  
This is a female  
terminal.  
1
2
3
4
5
6
7
8
*4 Selects which functions in “MARKER” are activated, non-“R-” items or “R-” items (page 11).  
*5 Displays the information shown when the button of the current input is pressed (“On the Status Display” on page 7).  
While controlling with the MAKE system, the information is displayed only at the moment of short-circuiting.  
*6 While controlling with the MAKE system, the level meter is switched between displayed (short-circuiting) and hidden  
(opening). When “LEVEL METER ch” is set to “OFF,” the level meter is not displayed (“NO EFFECT” appears). While  
controlling with the TRIGGER system, the number of the audio channels displayed is changed (between OFF, 12CH  
and 8CH).  
*2 The 6th pin terminal controls turning on or off the tally lamp (available to control even when the 7th pin terminal is  
invalid.)  
*3 The 7th pin terminal makes the external control valid/invalid. Make sure to control the terminal by the MAKE system.  
*7 While controlling with the MAKE system, the wave form monitor will not disappear until opening the terminal even when  
“AUTO OFF” is set to “ON.”  
*8 While controlling with the MAKE system, the screen is switched between normal screen (opening) and blue screen  
(short-circuiting). While controlling with the TRIGGER system, the screen changes as follows:  
You cannot change the functions assigned to the pin terminals from 6th to 8th.  
• When “FORMAT INDICATOR” in “FUNCTION SETTING” is set to “ON,the TALLY lamp cannot be controlled  
by the external control (page 14)  
You cannot assign the same function to different pin terminals.  
• The TRIGGER system switches each function by short-circuiting the pin terminal for about 1 second and  
opening it.  
Normal screen  
Red screen  
Blue screen  
Green screen  
To assign the functions to the pin terminals  
For the operation procedure, see page 7.  
Operation of the external control  
1 Select “REMOTE SETTING” on the SET-UP MENU.  
1 Set “TYPE SEL.of “REMOTE SETTING” to “MAKE” or “TRIGGER” in the SET-UP MENU.  
2 Short-circuit the 7th pin terminal (ENABLE) to the 8th pin terminal (GND) so that the monitor can be controlled  
by the external control.  
2 Set “TYPE SEL.to “SET.”  
3 Select a pin name (“PIN1” – “PIN5”) for which you want to assign a function, then select the function you want  
to assign.  
3 When the “MAKE” system is selected: Operate each function by short-circuiting the corresponding pin terminal  
• For selectable functions, see the table on the right.  
to the 8th pin terminal (GND) or opening it.  
When the “TRIGGER” system is selected: Operate each function by pulse control, that is short-circuiting the  
corresponding pin terminal to the 8th pin terminal (GND) for about 1 second and opening it.  
• When changing the input with MAKE system, only one pin terminal must be short-circuited. (Other pin terminals  
must be opened.)  
• When selecting the TRIGGER system, you can operate only one function at a time. Operate the functions one  
by one.  
<Basic command list>  
7 Using the RS-232C system  
No.  
1
Commands  
N
N
Functions  
Starts communication (connection)  
Terminates communication (termination)  
Data  
No data  
No data  
You can control the monitor from a personal computer etc. via the RS-232C terminal.  
• Consult your dealer for the details of the external control specification.  
!
!
0
0
0
0
B
B
C
C
1
0
Cr  
Cr  
2
Displays the MAIN MENU/Quits the menu  
operation  
<Communication specifications>  
Baud Rate: 4800 bps  
Data Bits: 8 bits  
Parity: No parity  
Stop Bits: 1 bit  
Flow Control: No control  
3
!
0
0
B
M E  
N
U
Cr  
No data  
4
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
U
D
A
A
S
P
P
I
P
O
D
D
E
Cr  
No data  
Moves the cursor upward (  
)
5
W N Cr  
No data  
Moves the cursor downward (  
)
6
7
8
9
J
J
T
R
L
U
Cr  
Cr  
P
Makes setting/adjustment (  
Makes setting/adjustment (  
Displays the SET-UP MENU  
Turns on the monitor  
)
)
No data  
No data  
No data  
No data  
No data  
No data  
No data  
No data  
No data  
No data  
No data  
00 – 30  
00: Off, 01: On  
00: 4:3, 01: 16:9  
Communication Code: ASCII Code  
• Use a straight cable with a D-sub 9-pin connector (male for the monitor, female for the personal computer).  
Cr  
W 1 Cr  
W 0 Cr  
N
N
N
I
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
Turns off the monitor (standby)  
Selects “SDI 1” input  
Selects “SDI 2” input  
Selects “VIDEO/COMPO.input  
Displays the status*2  
Increases the volume level  
Decrease the volume level  
Adjusts the volume level  
Turns muting on/off  
<Command outline>  
All commands consist of the following segments.  
A
B
C
S
L
Cr  
Cr  
Cr  
P
S
S
x
T
x
I
I
Header  
Monitor ID (00)  
Command ID  
Function  
Data  
Cr (0Dh)  
D
V
V
V
A
A
Cr  
Cr  
Cr  
x*1 Cr  
E
Header  
P
M N  
“!”: Operation commands from the personal computer, etc. For details, see <Basic command list> on the right.  
“?”: Reference commands from the personal computer, etc.  
“@”: Status returns from the monitor  
O
M U  
L
x
x*1 Cr  
S
P
x*1 Cr  
Changes the aspect ratio  
To start communication, send the connection command from the personal computer etc.  
To terminate the communication, send the termination command from the personal computer etc.  
• “Cr” is 0Dh.  
• The commands for starting communication (connection) (No. 1), terminating communication (termination)  
(No. 2), and turning on the monitor (No. 9) can be used while the monitor is off (on standby).  
Example of communication procedures  
1 Starting the communication: connection command  
(!00BCN1Cr)  
*1 Enter the appropriate data to “xx”.  
*2 Displays the information shown when the button of the current input is pressed (“On the Status Display” on page 7).  
2 Monitor’s status (@00BOKCr)  
Monitor  
<Specifications of the RS-232C terminal>  
3 Selecting “SDI 1” input (!00BINACr)  
4 Monitor’s status (@00BOKCr)  
PC, etc.  
Pin No.  
Signal  
NC  
5 Terminating the communication: termination command  
(!00BCN0Cr)  
1
2
3
4
5
6
7
8
9
RXD  
TXD  
NC  
6 Monitor’s status (@00BOKCr)  
This is a female  
terminal.  
GND  
NC  
RTS  
CTS  
NC  
• The 7th terminal and the 8th terminal are connected.  
ENGLISH  
17  
18  
Troubleshooting  
Solutions to common problems related to the monitor are described here. If none of the solutions presented here  
solve the problem, unplug the monitor and consult an authorized dealer or service center.  
Symptom  
Probable cause and corrective action  
Page  
Symptom  
Probable cause and corrective action  
Page  
6
8
8
8
• Adjust the picture contrast or brightness by using the adjustment  
knobs on the front panel. Or, adjust “CONTRAST” or “BRIGHT” of  
“PICTURE SUB ADJ.in the SET-UP MENU.  
6, 14  
• Press the  
button.  
The picture becomes  
blurred.  
Turn on the POWER switch or DC switch on the rear panel.  
• Firmly insert the AC power plug or DC 12 V power plug.  
• When using a DC 12 V power supply, charge the battery or replace it  
with a charged one.  
No power supply  
• Check whether the input signal format is acceptable on the monitor.  
• Check the setting of “ASPECT” in the MAIN MENU.  
7, 9  
10  
Wrong picture position, • Adjust the horizontal picture position in “H. POSITION” of the SET-  
14  
• Select the correct input.  
• Connect the signal cable firmly.  
6
8
wrong picture size.  
UP MENU.  
No picture with the  
power on  
• For some signals, the picture cannot be displayed fully in the  
effective screen area. There is no sure method to solve this problem.  
Turn on the power of the connected component and set the output  
correctly.  
• Check whether the input signal format is acceptable on the monitor.  
9
• The items which are not available for the current input or the current  
input signal are not displayed on the menu. Change the input or the  
input signal.  
• The items controlled by the MAKE system do not appear on the  
menu.  
• Adjust the volume level.  
6
6
8
Some items do not  
appear on the menu.  
• Deactivate the muting function.  
• Connect the signal cable firmly.  
Turn on the power of the connected component and set the output  
correctly.  
16  
No sound  
• Set “CONTROL LOCK” in the SET-UP MENU to “OFF.”  
You cannot use the buttons for the items controlled by the MAKE  
system. Disable the external control.  
15  
16  
Buttons on the monitor  
do not work.  
“OTHERS” or “Out of  
range” appears.  
• Check whether the input signal format is acceptable on the monitor.  
7, 9  
• Select the correct input.  
• Connect the signal cable firmly.  
6
8
“NO SYNC” appears.  
Turn on the power of the connected component and output video  
signals. Or, check whether the video output of the component (video  
output setting of the VCR) is set correctly.  
• Adjust each picture adjustment knob on the front panel or adjust the  
items of “PICTURE SUB ADJ.in the SET-UP MENU. Or, perform  
“reset” in “PICTURE SUB ADJ.”  
6, 14  
• Check if the screen mode is other than normal screen, by using SCR.  
CHK. button.  
6
Wrong color, no color  
• Select the proper color system (“COLOR SYSTEM”) in “FUNCTION  
SETTING” of the SET-UP MENU.  
• Adjust the items of “WHITE BALANCE SET.” in the SET-UP MENU.  
Or, perform “reset” in “WHITE BALANCE SET.”  
14  
14  
The following are not malfunctions.  
• When a still image is displayed for a long time, it may remain indistinctly on the screen after the picture has  
changed. Though the remaining picture will disappear after a while, there may be a case that it remains  
for a long period depending on the length of time the still image was displayed for. This is due to the  
characteristics of the LCD display and is not a malfunction.  
• Red spots, blue spots and green spots on the panel surface are a normal characteristic of LCD displays,  
and not a problem. The LCD display is built with very high precision technology; however, be aware that a  
few pixels may be missing or constantly lit.  
• The following symptoms are problems only when pictures or sounds are not played back normally.  
– A slight electric shock occurs when you touch the monitor.  
– The top and/or rear panel of the monitor becomes hot.  
– The monitor emits a cracking noise.  
– The monitor emits a mechanical noise.  
7 Self-check program  
This monitor has a self-check function, which allows it to detect malfunctions and alert you. This makes  
troubleshooting easier. Whenever a problem occurs, one or some of the self-check lamps will flash. If this  
happens, follow the steps below and contact your dealer to resolve the problem.  
When the screen goes blank and one or some of the self-check lamps on the front control panel start  
flashing...  
1 Check which lamps are flashing.  
2 Press  
button to turn off (on standby) the monitor.  
3 Turn off the POWER switch and DC switch on the rear panel.  
4
When the AC power supply is used: Disconnect the AC power cord from the AC outlet.  
When a DC 12 V power supply is used: Detach the battery or disconnect the plug  
from the DC IN terminal.  
5 Contact your dealer with the information about which lamps were flashing.  
• If you turn on the monitor soon after turning it off (or after a short-term power failure), the self-check lamps may  
flash and no image may be displayed. When this happens, turn off power and wait at least 10 seconds before  
turning on the monitor again. If the self-check lamps do not flash, you can use the monitor as normal.  
ENGLISH  
19  
20  
Maintenance  
Unplug this product from the wall outlet before cleaning.  
Screen  
To avoid irreparable change in appearance of the screen such as uneven color, discoloration, scratches, be  
careful about the following:  
• Do not paste or stick anything using any glues or adhesive tapes.  
• Do not write anything on the screen.  
• Do not strike the screen with a hard object.  
• Avoid condensation on the screen.  
• Do not wipe the screen with solvent such as alcohol, thinner, or benzine.  
• Do not wipe the screen forcefully.  
Wipe stains off the screen with a soft cloth. If the screen gets heavily stained, wipe it with a soft cloth soaked in  
water-diluted neutral detergent and wrung well, then wipe with a soft dry cloth.  
Cabinet  
To avoid the deterioration or damages of the cabinet such as its paint’s peeling away, be careful about the  
following:  
• Do not wipe the cabinet using solvent such as alcohol, thinner, or benzine.  
• Do not expose the cabinet to any volatile substance such as insecticides.  
• Do not allow any rubber or plastic in contact for a long time.  
• Do not wipe the cabinet forcefully.  
Wipe stains off the cabinet with a soft cloth. If the cabinet gets heavily stained, wipe it with a soft cloth soaked in  
water-diluted neutral detergent and wrung well, then wipe with a soft dry cloth.  
Ventilation openings  
Use a vacuum cleaner to get rid of the dust around the intakes (all the openings). If a vacuum cleaner is not  
available, use a cloth and wipe it off. Leaving the dust around the intakes may prevent proper temperature control  
and cause damage to the product.  
Specifications  
7 General  
7 Input/output terminals  
Model name  
Type  
DT-V9L3D  
VBS/Y  
Composite signal/analog component (Y) signal input/output:  
1 line, BNC connector x 2  
Multi format LCD monitor  
Type 9 wide format  
15:9  
Screen size  
Aspect ratio  
LCD panel  
1 V(p-p), 75 Ω  
VIDEO/COMPONENT  
(IN/OUT)  
* The input (IN) and output (OUT) terminals are bridge-  
connected (auto termination)  
PB, PR  
9˝ wide, IPS-Pro  
Width: 195 mm  
Height: 117 mm  
Effective screen size  
Analog component (PB, PR) signal input:  
1 line, BNC connector x 2  
Number of pixels displayed  
Number of colors displayed  
Viewing angle (TYP.)  
Brightness  
800 x 480  
0.7 V(p-p), 75 Ω  
16.77 million  
E. AUDIO HD/SD SDI (IN 1)  
E. AUDIO HD/SD SDI (IN 2)  
Digital signal input (compatible with EMBEDDED AUDIO signals):  
auto detection, 1 line, BNC connector x 1  
170° (Horizontally), 170° (Vertically)  
350 cd/m2  
E. AUDIO HD/SD SDI  
(SWITCHED OUT)  
Digital signal output (compatible with EMBEDDED AUDIO signals):  
1 line switched out, BNC connector x 1  
Contrast ratio (TYP.)  
400:1  
Compliant video signal format  
“Available signals” on page 9  
AUDIO (IN)  
Analog audio signal input:  
1 line, RCA connector x 1,  
500 mV (rms), high impedance  
HD SDI: BTA S-004B, SMPTE292M  
SD SDI: ITU-R BT.656: 525/625  
SMPTE259M: 525  
Format  
AUDIO (MONITOR OUT)  
EARPHONE  
Analog audio signal output: 1 line, RCA connector x 2,  
500 mV (rms)  
EMBEDDED AUDIO: SMPTE299M, SMPTE272M  
Audio output  
Internal speaker: 1.0 W  
Monaural mini jack (3.5 mm in diameter) x 1  
Operating temperature: 0°C – 40°C  
Operating humidity: 20 % – 80 % (non-condensing)  
* Slightly variable depending on ambient conditions for installation.  
REMOTE (MAKE/  
TRIGGER)  
“Using the MAKE/TRIGGER system” on page 16  
Operating conditions  
REMOTE (RS-232C)  
“Using the RS-232C system” on page 17  
AC 220 – 240 V, 50 Hz/60 Hz  
DC 12 – 17 V  
Power requirements  
Rated current  
0.25 A (AC 220 – 240 V)  
1.7 A (DC 12 – 17 V)  
Width:  
222.4 mm  
Height: 218 mm (at the higher position), 181 mm (at the lower position),  
176 mm (without stand)  
External dimensions  
(excluding protruding parts)  
Depth:  
185 mm (at the higher position), 202 mm (at the lower position),  
116 mm (without stand)  
3.6 kg (with the stand)  
2.7 kg (without the stand)  
Weight  
AC power cord x 2, Power cord holder x 1, Screw x 2 (for power cord holder),  
Protective filter x 1, Screw (for protective filter) x 4  
Accessories  
Use the Anton Bauer Dionic 90 (mount: QR DXC-M3A) external battery.  
• For easy understanding, pictures and illustrations are shown by being emphasized, omitted or composed,  
and may be slightly different from actual products.  
• Design and specifications are subject to change without notice.  
CAUTION  
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.  
• All company names and product names mentioned herein are used for identification purposes only, and  
may be the trademarks or registered trademarks of their respective companies.  
Notice on transportation  
This monitor is precision equipment and needs dedicated packing material for transportation.  
Never use any packing material supplied from sources other than JVC or JVC-authorized dealers.  
ENGLISH  
21  
22  
Specifications (cont.)  
Unit: mm  
7 Dimensions  
<Front view>  
<Side view>  
<Rear view>  
• When the stand is attached to the  
higher position.  
• When the stand is attached to the  
lower position.  
116  
VESA mounting holes  
(8-M4, depth: 10 mm)  
100  
75  
27.5  
1.5  
222.4  
202  
13  
186  
185  
* at the higher position  
** at the lower position  
tapped hole (3/8˝)  
tapped hole (1/4˝)  
The lightning flash with arrowhead  
symbol, within an equilateral triangle is  
intended to alert the user to the presence  
of uninsulated “dangerous voltage”  
within the product’s enclosure that may  
be of sufficient magnitude to constitute a  
risk of electric shock to persons.  
CAUTION  
RISK OF ELECTRICAL SHOCK  
DO NOT OPEN  
The exclamation point within an  
equilateral triangle is intended to alert  
the user to the presence of important  
operating and maintenance (servicing)  
instructions in the literature  
To reduce the risk of electric shock. Do  
not remove cover (or back). No user  
serviceable parts inside. Refer servicing  
to qualified service personnel.  
CAUTION:  
accompanying the appliance.  
INSTRUCTIONS  
DT-V9L3DY  
Table of Contents  
MULTI FORMAT LCD MONITOR  
Safety Precautions .............................................. 2  
IMPORTANT SAFEGUARDS ........................... 2  
Installation............................................................ 4  
To adjust the stand height ................................ 4  
Daily Operations / Connections ......................... 6  
Front panel ....................................................... 6  
Rear panel........................................................ 8  
Available signals............................................... 9  
Menu Configuration—MAIN MENU .................. 10  
Menu Configuration—SET-UP MENU............... 14  
External Control................................................. 16  
About the external control .............................. 16  
Using the MAKE/TRIGGER system ............... 16  
Using the RS-232C system............................ 17  
Troubleshooting................................................. 18  
Self-check program ........................................ 19  
Maintenance....................................................... 20  
Specifications .................................................... 21  
General........................................................... 21  
Input/output terminals..................................... 21  
Dimensions..................................................... 22  
LCT2530-001A-H  
2
Safety Precautions  
WARNING:TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO  
RAIN OR MOISTURE. NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE  
PLACED ON THE APPARATUS.  
Under the following conditions,  
1. Turn off the power.  
2. Unplug this product from the wall outlet.  
3. Refer service to qualified service personnel.  
a) When the product emits smoke or unusual  
smell.  
b) When the product exhibits a distinct change in  
performance—for example, no picture or no  
sound.  
c) If liquid has been spilled, or objects have fallen  
on the product.  
d) If the product has been exposed to rain or water.  
e) If the product has been dropped or damaged in  
any way.  
f) When the power supply cord or plug is  
damaged.  
• The AC power supply is controlled by turning on/  
off the POWER switch on the rear panel. If the  
product is installed in a place where you cannot  
easily turn on/off the POWER switch, control the  
AC power supply by plugging/unplugging the  
power cord into/from the AC outlet. In this case,  
install the product as close to the AC outlet as  
possible, and leave enough space for plugging/  
unplugging the power cord. If the product is  
installed in a place where you cannot easily  
plug/unplug the power cord, equip an easily  
accessible device to the wiring of the building for  
turning on/off the power.  
• When the product is left unattended and unused  
for a long period of time, unplug it from the wall  
outlet and disconnect the cable system.  
• Do not overload wall outlets, extension cords, or  
convenience receptacles on other equipment as  
this can result in a risk of fire or electric shock.  
• Use only the accessory cord designed for this  
product to prevent shock.  
IMPORTANT SAFEGUARDS  
Electrical energy can perform many useful functions. This unit has been engineered and manufactured to assure  
your personal safety. But IMPROPER USE CAN RESULT IN POTENTIAL ELECTRIC SHOCK OR FIRE.  
In order not to defeat the safeguards incorporated into this product, observe the following basic rules for its  
installation, use, and service. Please read these “IMPORTANT SAFEGUARDS” carefully before use.  
• All the safety and operating instructions should be read before the product is operated.  
• The safety and operating instructions should be retained for future reference.  
• All warnings on the product and in the operating instructions should be adhered to.  
• All operating instructions should be followed.  
POWER CONNECTION  
The power supply voltage rating of this product is AC 120 V.  
The power cord attached conforms to the following power supply voltage and countries. Use only the power  
cord designated to ensure safety and EMC regulations of each country.  
• Do not install this product in the following places:  
– in a damp or dusty room  
– where the product is exposed to soot or  
steam, such as near the cooking counter or a  
humidifier  
– near heat sources  
– where condensation easily occurs, such as  
near the window  
• Do not place this product on an unstable cart,  
stand, or table. The product may fall, causing  
serious injury to a child or adult, and serious  
damage to the product.  
The product should be mounted according to the  
manufacturer’s instructions, and should use a  
mount recommended by the manufacturer.  
• Do not use this product near water.  
• Be sure to install the product in the place where  
proper temperature and humidity are kept (  
“Operating conditions” on page 21).  
This product becomes hot during its use. Take  
enough care when handling the product.  
For U.S.A. and Canada:  
AC 120 V  
This plug will fit only into a grounded power outlet. If you are unable to insert the plug into the outlet, contact  
your electrician to install the proper outlet. Do not defeat the safety purpose of the grounded plug.  
• This product should be operated only with the type of power source indicated on the label. If you are not  
sure of the type of power supply of your home, consult your product dealer or local electric power company.  
• Slots and openings in the cabinet are provided  
for ventilation. These ensure reliable operation  
of the product and protect it from overheating.  
These openings must not be blocked or covered.  
• Never push objects of any kind into this product  
through openings as they may touch dangerous  
voltage points or short-circuit the parts, which  
could result in a fire or electric shock.  
Warning: This is a class A product. In a domestic environment this product may cause radio interference in  
which case the user may be required to take adequate measures.  
• Never spill liquid of any kind on the product.  
• Never place anything on the product. (Placing  
liquids, naked flames, cloths, paper, etc. on the  
product may cause a fire.)  
• Before connecting other products such as VCR’s and personal computers, you should turn off the power of  
this product for protection against electric shock.  
• Do not use attachments not recommended by the manufacturer as they may be hazardous.  
When replacement parts are required, be sure the service technician has used replacement parts  
specified by the manufacturer or equivalents. Unauthorized substitutions may result in fire, electric shock, or  
other hazards.  
• Do not apply any strong shock to the LCD panel.  
(Do not hit any object against it or push it with a  
sharp-pointed tool.)  
• Do not put heavy objects on the product.  
• Do not step on or hang on the product.  
Upon completion of any service or repairs to this product, ask the service technician to perform safety  
checks to determine that the product is in proper operating condition.  
Do not attempt to service this product yourself, as  
opening or removing covers may expose you to  
dangerous voltages and other hazards. Refer all  
service to qualified service personnel.  
Caution for use of the product in the high  
temperature  
The rating label is on the bottom of the monitor.  
Do not use the product in places of high  
temperature; otherwise, parts of this product or  
the LCD panel may be damaged. This product  
is equipped with a temperature sensor to give  
warning if the temperature becomes too high. If  
the temperature exceeds the range of normal use,  
“TEMP. OVER” is displayed, and the power is  
turned off automatically if the temperature becomes  
any higher. In this case, move the product to a  
place of low temperature to let it cool down.  
Do not use the product for a long time if the sound  
is distorted.  
Use only the power source specified on the unit.  
• AC power: 120 V, 50 Hz/60 Hz  
• DC power: 12 – 17 V  
WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS  
APPARATUS TO RAIN OR MOISTURE.  
IMPORTANT SAFETY INSTRUCTIONS  
1) Read these instructions.  
WARNING: THIS APPARATUS MUST BE CONNECTED TO A MAINS SOCKET  
OUTLET WITH A PROTECTIVE EARTHING CONNECTION.  
CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED.  
REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE.  
2) Keep these instructions.  
3) Heed all warnings.  
4) Follow all instructions.  
5) Do not use this apparatus near water.  
6) Clean only with dry cloth.  
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.  
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including  
amplifiers) that produce heat.  
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one  
wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the  
third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for  
replacement of the obsolete outlet.  
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point  
where they exit from the apparatus.  
11) Only use attachments/accessories specified by the manufacturer.  
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or  
sold with the apparatus. When a cart is used, use caution when moving the cart/  
apparatus combination to avoid injury from tip-over.  
13) Unplug this apparatus during lightning storms or when unused for long periods of time.  
14) Refer all servicing to qualified service personnel. Servicing is required when the  
apparatus has been damaged in any way, such as power-supply cord or plug is  
damaged, liquid has been spilled or objects have fallen into the apparatus, the  
apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.  
15) Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be  
placed on the apparatus.  
FCC NOTICE  
CAUTION: Changes or modifications not approved by JVC could void the user’s authority to operate the  
equipment.  
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device,  
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against  
harmful interference when the equipment is operated in a commercial environment. This equipment generates,  
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction  
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential  
area is likely to cause harmful interference in which case the user will be required to correct the interference at  
his own expense.  
IMPORTANT RECYCLING INFORMATION  
This product has a fluorescent lamp that contains mercury. Disposal of these materials  
may be regulated in your community due to environmental considerations. For disposal  
or recycling information, please contact your local authorities or for USA, the Electronic  
16) Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.  
17) When discarding batteries, environmental problems must be considered and the local rules or laws governing the  
disposal of these batteries must be followed strictly.  
3
4
Installation  
• Do not rest your arm on the monitor or lean against the monitor.  
• Do not touch the LCD panel when installing the monitor.  
• Be sure to install the monitor securely to prevent the monitor from falling over, which may cause damage to the monitor  
or injury.  
CAUTION  
Higher position  
When shipped from factory, the stand is attached to the monitor.  
You can tilt the monitor from about 20° upward to about 10° downward.  
Monitor  
Stand  
• When the monitor is not  
tilted (0°), the guidelines  
align as illustrated.  
About 20°  
0°  
Guidelines  
About 10°  
CAUTION  
• Be careful not to pinch your fingers in the gap between the monitor and the stand.  
• When the stand is attached to the lower position (page 5), you cannot tilt the monitor downward.  
7 To adjust the stand height  
Attachment screws  
You can select the stand height according to your preference—higher position or lower position.  
To change the stand height, change the position of the screw hole used for attaching the stand.  
• When shipped from factory, the stand is attached to the higher position.  
• Before adjusting the stand height, set the monitor angle to 0°.  
CAUTION  
• Lay the monitor on a cloth with the LCD panel facing down to prevent the LCD panel from being damaged.  
• Depending on the type of external batteries, the stand cannot be attached or detached when the external battery is  
attached on the monitor.  
• When the stand is attached on the lower position, some types of external batteries cannot be attached to the monitor.  
Guide holes (only for attaching  
to the higher position)  
Screw holes for lower position  
Rear panel of the monitor  
Screw holes for higher position  
Lower position  
To prevent an accidental fall  
Fix the monitor to a wall by using strings.  
Attachment screws  
Fixing the monitor  
Attach the hook (not provided) to the VESA mounting holes on the rear panel (use the two 100 mm pitch holes  
on the upper side) using M4 x 10 mm screws (not provided). Bind the hooks on the rear panel of the monitor to a  
wall or a pillar using durable string.  
Stand  
Monitor  
Hook (not provided)  
Hook and screws (M4 x 10 mm)  
(not provided)  
5
6
Daily Operations / Connections  
7 Front panel  
• “NO EFFECT” is displayed when you press a button which is not available for the current input or signal format (the lamp  
lights even when the function does not actually work).  
• The items controlled by the MAKE system cannot be controlled by the buttons on the front panel (“REMOTE ON” is displayed  
and the lamps do not light).  
Tally lamp  
This lamp is controlled by the tally function of the MAKE/TRIGGER terminal.  
• This lamp can also be used as the format indicator (“FORMAT  
INDICATOR” in “FUNCTION SETTING” on page 14).  
8 DYNAMIC button/lamp  
w
button  
Adjusts the picture to be suitable for a bright place.  
• When the DYNAMIC lamp lights:  
– “BACK LIGHT” and “PICTURE SUB ADJ.are  
not displayed on the menu.  
Turns on and off (on standby) the monitor.  
• The power switches (the POWER switch and  
DC switch) are equipped on the rear panel of the  
monitor (1, 3 on page 8).  
– The setting of “BACK LIGHT” is ineffective.  
(page 10, 14)  
To turn off the monitor completely, turn off the  
POWER switch and DC switch.  
9 MARKER button/lamp  
e VOL. +/– buttons  
1 Screw holes for attaching protective filter  
(provided)  
5 MUTING button  
Displays/hides the area marker and the safety  
marker.  
• Select the size and the style of the markers in  
“MARKER” of the MAIN MENU (page 11).  
• The marker is not displayed when it is set to  
“OFF” in “MARKER.(“NOTE” on page 11)  
Adjusts the volume.  
Turns off the sound when no menu screen is  
displayed.  
To cancel the function, press the button again or  
press VOL. +/– buttons.  
r MENU button  
• Attach the protective filter by using the provided  
screws.  
• Attach the filter to the LCD panel with the frosted  
side of the filter facing outwards (when shipped  
from the factory, a protective film and a sticker  
are attached to the frosted side).  
Activates/deactivates the display of the MAIN MENU.  
(“Menu Operations” on page 7)  
t W. F. M. (Wave form monitor) button/lamp  
Displays/hides the indication of the wave form  
monitor.  
6
/
/
/
buttons  
When a menu screen is displayed  
Selects or adjusts menu items. (“Menu  
Operations” on page 7)  
When no menu screen is displayed  
Selects the audio channels of EMBEDDED AUDIO  
signals, or adjusts the volume. (“Audio Channel  
Selection” on page 7)  
• Pressing button while holding button displays  
the SET-UP MENU. (“Menu Operations” on  
page 7)  
p Input select buttons/lamps  
Selects an input.  
• Adjust the settings of the wave form monitor in  
“WAVE FORM SETTING” of the MAIN MENU  
(page 13).  
• Closed captions (page 13) disappear when the  
wave form monitor is displayed.  
CAUTION  
VIDEO/COMPO.: VIDEO/COMPONENT terminal  
SDI 1: E. AUDIO HD/SD SDI (IN 1) terminal  
SDI 2: E. AUDIO HD/SD SDI (IN 2) terminal  
• The lamp for the selected input lights.  
• Select an appropriate setting of “VIDEO/COMPO.  
SEL.(page 10).  
• Use only the provided screws to avoid damaging the  
monitor.  
• When attaching the protective filter, do not fasten  
screws too tightly; otherwise, the protective filter may  
be damaged.  
y DC lamp  
2 Speaker (monaural)  
When the DC 12 V power voltage is being lowered  
due to the battery consumption, the lamp changes  
to orange from green. When the voltage becomes  
lower than a certain level, the monitor automatically  
turns off and the lamp turns to red.  
• Make sure to turn off the POWER switch and  
DC switch on the rear panel before replacing the  
battery.  
• The length of time that the lamp lights in orange  
differs depending on the type of battery or the  
battery condition. It is recommended to replace  
the battery when the lamp turns to orange.  
q Power lamp  
The speaker emits the same audio signal as  
emitted from the AUDIO (MONITOR OUT) OUT 1  
terminal. (9 AUDIO (MONITOR OUT) terminals”  
on page 8)  
Unlit: The monitor is completely off (both the  
POWER switch and DC switch on the rear panel  
are turned off).  
Lights in green: The monitor is on.  
Lights in orange: The monitor is off (on standby).  
Flashes in orange: The monitor is in the P. SAVE  
(power save) mode (“NO SYNC ACTION” in  
“SYNC FUNCTION” on page 13).  
7 SCR. CHK. (Screens check) button/lamp  
Displays only the selected element (R, G, B, or the  
luminance) of video signal.  
3 EARPHONE (earphones) jack (monaural)  
Connect earphones to this jack to listen to the same  
sound as produced from the speaker.  
• Each time you press this button, the screen  
changes in the following order.  
Normal screen  
Monochrome screen  
4 Picture adjustment knob  
PHASE: Adjusts the picture hue.  
Blue screen Green screen  
Red screen  
CHROMA: Adjusts the picture color density.  
BRIGHT: Adjusts the picture brightness.  
CONTRAST: Adjusts the picture contrast.  
Menu Operations  
Audio Channel Selection  
On the Information Display  
On the Status Display  
Select audio channels emitted from the speaker  
and the AUDIO (MONITOR OUT) OUT1/OUT2  
terminals, when EMBEDDED AUDIO signals  
come in to the E. AUDIO HD/SD SDI terminal (IN1  
or IN2) and SDI input (1 or 2) is selected.  
• The speaker emits the same audio signal  
emitted from the AUDIO (MONITOR OUT) OUT  
1 terminal.  
The monitor displays the information below  
depending on the settings of the menu.  
If you press the input button of the current input,  
the status of the input signal and setting of muting  
are displayed for about 3 seconds.  
• Make the setting to display/hide the status in  
“STATUS DISPLAY” of the “INFORMATION” (☞  
page 15).  
• When “STATUS DISPLAY” is set to “AUTO” or  
“ON,the status below is also displayed in the  
following cases:  
1 Display the menu.  
To display the MAIN MENU  
\
Press MENU button.  
To display the SET-UP MENU  
\
Press button while holding button.  
MAIN MENU  
• The setting is memorized for each input (SDI 1  
and SDI 2).  
– When you change the input  
– When the signal condition of the current input  
changes  
– When you turn on the monitor  
• When “STATUS DISPLAY” is set to “ON,the  
signal format will remain displayed 3 seconds  
after the status is displayed.  
1 Press or button when a menu  
Selected item  
1 Audio level meter  
is not displayed.  
• Not displayed when no signal comes in for  
the SDI inputs or “LEVEL METER ch” is set  
to “OFF.”  
Operation guide  
SET-UP MENU  
The screen for audio channel selection is  
displayed.  
• The screen for audio channel selection  
automatically disappears in about 30  
seconds after the previous operation.  
“AUDIO SETTING” and “NOTE” on page 12  
2 Signal format  
Selected item  
• Displayed when “STATUS DISPLAY” is set  
to “ON.(“INFORMATION” on page 15)  
• For the contents displayed, see “On the  
signal format” below and “Available signals”  
on page 9.  
Audio channel selection screen  
Selected item  
Operation guide  
3
Source name assigned in “CHARACTER SET.”  
• Displayed when “SOURCE ID” is set to “ON.”  
• Displayed in large letters when “STATUS  
DISPLAY” is set to “OFF” or “AUTO.”  
1 Signal format  
2 Press  
buttons to select an item,  
then press button.  
• For the contents displayed, see “On the  
signal format” below and “Available signals”  
on page 9.  
2 Press  
buttons to select the  
channel to set.  
• For some items, adjustments will be made by  
pressing  
.
“INFORMATION” on page 15  
2 Setting of “VIDEO/COMPO. SEL.”  
page 10  
3 Setting of “MUTING”  
• E.AUDIO OUT1/SP:  
AUDIO (MONITOR OUT) OUT1 terminal and  
the speaker.  
• E.AUDIO OUT2:  
AUDIO (MONITOR OUT) OUT2 terminal.  
4 Time code  
• Displayed when “TIME CODE” is set to “ON.”  
(“TIME CODE” on page 11)  
• When the input signal includes no time code,  
“TC – –:– –:– –:– –” is displayed.  
5 CRC error indication  
• Displayed only when muting is activated.  
5 MUTING button” on page 6  
3 Press  
buttons to select an  
Ex.: When “MARKER” in the MAIN  
MENU is selected  
• Displayed when “CRC ERROR” is set to  
“ON.(“INFORMATION” on page 15)  
• A red square is displayed when an error  
occurs.  
audio channel.  
On the signal format  
The following messages appear depending on the  
type of input signals and their conditions.  
Each time you press the button, the audio  
channel changes as follows:  
3 Press  
then press  
adjustments.  
buttons to select an item,  
1/2/3/4/5/6/7/8/9/10/11/12/1+2/3+4/5+6/7+8/  
9+10/11+12/1G(1–4)/2G(5–8)/3G(9–12)/  
1G+2G(1–8)/1-3G(1–12)  
buttons to make  
When no video signal comes in  
\
“NO SYNC”  
When a noncompliant video signal comes in  
“Out of range”  
\
4 Press MENU button to finish the  
4 Press MENU button.  
The screen for audio channel selection  
disappears.  
When “COLOR SYSTEM” (“FUNCTION  
menu operation.  
SETTING” on page 14) is set to “AUTO” and the  
noncompliant composite video signals come in  
• Pressing MENU button repeatedly  
deactivates the display of the menu.  
\
“OTHERS”  
7
8
Daily Operations / Connections (cont.)  
5 VIDEO/COMPONENT terminals (BNC)  
IN: Input terminals for the composite (VBS) and the  
analog component (Y/PB/PR) signals.  
• Select the signal type in “VIDEO/COMPO. SEL.”  
corresponding to the type of the input signal (☞  
page 10).  
p REMOTE terminals  
7 Rear panel  
Terminals for controlling the monitor by an external  
control. (“External Control” on page 16)  
q Carry handle  
Use this handle when carrying the monitor.  
w Security slot  
OUT: Output terminal for the composite (VBS) and  
the analog component (Y) signals.  
Attach a security wire to this slot.  
e Screw holes for external battery attachment  
Attach external battery for DC 12 V power supply  
by using 2 screw holes. Choose the appropriate  
screw holes from 1, 2, 3 or 4, according to the type  
of external battery.  
6 AUDIO IN terminal (pin jack)  
Input terminal for the analog audio signals.  
• Use this terminal for the analog audio connection  
of the SDI.  
7 E. AUDIO HD/SD SDI (SWITCHED OUT) terminal  
(BNC)  
• Use the Anton Bauer Dionic 90 (mount: QR DXC-  
M3A) external battery.  
Output terminal for the HD/SD SDI signals.  
• The SDI signals of the current input (SDI 1 or SDI  
2) are re-clocked, then emitted.  
• When an input other than SDI 1 and SDI 2 is  
selected, the SDI signal of the input selected last  
time is emitted from this terminal.  
• The signals are emitted from this terminal only  
when the monitor is on or in “P.SAVE” (power  
save) mode.  
CAUTION  
Do not use the external battery for DC 24 V  
power supply.  
• Use only the battery specified above. If a heavy  
battery is used, it may fall off depending on the  
way the monitor is used.  
1 POWER switch  
Turns AC power on or off.  
You need to press  
button (w on page 6)  
to use the monitor after turning on the POWER  
switch.  
Note for connections  
2 AC IN terminal  
8 E. AUDIO HD/SD SDI (IN 1, IN 2) terminals (BNC)  
Input terminals for the HD/SD SDI signals.  
• The terminals accept also EMBEDDED AUDIO  
signals including up to 12 audio channels with a  
sampling frequency of 48 kHz.  
AC power input connector.  
Connect the provided AC power cord to an AC  
outlet.  
• Attach the provided power cord holder to prevent  
accidental disconnection of the AC power cord (☞  
“Attaching the Power Cord Holder” on page 9).  
• Before making any connections, turn off all the  
equipment.  
• Use a cord whose plugs correctly match the  
terminals on this monitor and the equipment.  
• Plugs should be firmly inserted; poor connections  
could cause noise.  
• When unplugging a cord, be sure to grasp its plug  
and pull it out.  
• DO NOT connect the power cord until all connections  
are complete.  
9 AUDIO (MONITOR OUT) terminals (pin jack)  
Output terminals for the analog audio signal.  
• The terminals emit the audio signals coming  
in from the AUDIO IN terminal or EMBEDDED  
AUDIO signals coming in from the E. AUDIO HD/  
SD SDI (IN 1 or IN 2) input terminal. (“Audio  
Channel Selection” on page 7)  
3 DC switch  
Turns the DC 12 V power on or off.  
You need to press  
button (w on page  
6) on the front panel to turn on the monitor after  
turning on the DC switch.  
• The monitor consumes the battery even while the  
monitor is on standby. To save battery life, turn  
off the DC switch.  
• Refer also to the user manual of each piece of  
equipment.  
• The signal is output from these terminals only  
when the monitor is on or in “P.SAVE” (power  
save) mode. (“NO SYNC ACTION” in “SYNC  
FUNCTION” on page 13)  
4 DC IN terminal  
• The EMBEDDED AUDIO signal...  
DC 12 V (maximum DC 17  
– is decoded into an analog signal, then emitted.  
– is emitted only when “SDI 1” or “SDI 2” is  
selected, and when EMBEDDED AUDIO  
signals come in to the E. AUDIO HD/SD SDI  
(IN 1 or IN 2) terminal.  
V) power input connector.  
• While using both the  
AC and DC 12 V power  
supply, AC power supply  
is preferentially used. If the AC power supply is  
cut off (for example, when turning off the POWER  
switch), the power supply automatically switches  
to the DC 12 V power supply.  
CAUTION  
Do not connect the power cord until all  
other connections are completed.  
When using DC 12 V power (maximum DC 17 V),  
check the DC IN terminal pin signal, and use the  
correct polarity. If the polarity is reversed, this  
could cause a fire or personal injury.  
7 Available signals  
Attaching the Power Cord Holder  
The following signals are available for this monitor.  
The provided power cord holder prevents accidental disconnection of the AC power cord from the AC IN  
terminal.  
Video signals  
• The power cord holder consists of two parts, a case and a cover.  
Input terminal  
VIDEO/COMPONENT  
Signal format shown  
in the status display  
No.  
Signal name  
E. AUDIO HD/  
SD SDI*1  
1
3
AC IN terminal  
VBS  
Y/PB/PR  
(Analog component)  
(page 7)  
Case  
(Composite)  
1
2
3
4
5
6
7
8
9
NTSC*2  
NTSC  
PAL  
PAL  
B/W50  
B/W60*2  
PAL  
NTSC  
CAUTION  
Make sure the plug will not be pulled out after the  
cover is attached to the case.  
CAUTION  
Use only the provided screws.  
480/60i  
480/60i  
480/59.94i*2  
576/50i  
480/60p  
480/59.94p  
480/59.94i  
576/50i  
To detach the cover  
2
480/60p  
480/59.94p  
576/50p  
720/60p  
720/59.94p  
720/50p  
1080/60i  
1080/59.94i  
1080/60i  
1080/59.94i  
1080/50i  
1080/60i  
1080/50i  
1080/59.94i  
1080/24psf  
1080/23.98psf  
10 576/50p  
11 720/60p  
Cover  
12 720/59.94p  
13 720/50p  
14 1080/60i  
15 1080/59.94i  
16 1035/60i  
*3  
*4  
*3  
*5  
*4  
*3  
*4  
*3  
*5  
*4  
17 1035/59.94i  
18 1080/50i  
19 1080/30psF  
20 1080/25psF  
21 1080/29.97psF  
22 1080/24psF  
23 1080/23.98psF  
: Acceptable  
—: Not acceptable  
*1 Compatible with EMBEDDED AUDIO signals  
*2 When the number of vertical scanning lines of the incoming signal is 483, the picture is displayed with 480 lines.  
*3 The signal is recognized as 1080/60i.  
*4 The signal is recognized as 1080/59.94i.  
*5 The signal is recognized as 1080/50i.  
• Analog component signals are compatible with Y on sync signals.  
9
10  
Menu Configuration—MAIN MENU  
For the operation procedure, see page 7.  
PICTURE IMPROVEMENT  
Setting for the picture quality  
Item  
To do  
Setting value  
APERTURE*  
Select the frequency of the luminance signal compensated in  
“APERTURE LEVEL.”  
OFF, LOW, HIGH  
APERTURE  
LEVEL*  
Compensate the frequency response of the luminance signal of the  
video signal.  
01 – 10  
sub menu  
reset  
Display the sub menu which enables you to adjust the items of “PICTURE IMPROVEMENT” while  
viewing the actual picture.  
Restore the default settings for all the items in “PICTURE IMPROVEMENT.”  
Setting value: –20 – +20  
BACK LIGHT  
Adjusts the brightness of the display.  
• When the DYNAMIC lamp lights, this item does not appear on the menu (8 on page 6).  
Operation guide  
Shows the buttons for  
each operation.  
Setting value: OFF, ON  
FOCUS ASSIST  
Helps to focus the picture.  
• When “ON” is selected,  
– “PICTURE IMPROVEMENT” is not displayed on the menu.  
– The settings of “PICTURE IMPROVEMENT” are ineffective.  
• The menu automatically disappears in about 30 seconds after the previous operation.  
• Some items may not appear on the menu depending on the input or the input signal.  
• The items controlled by the MAKE system do not appear on the menu.  
Setting value: OFF, ON  
COLOR RANGE MODE  
Reduces the difference of the luminance level specific to the LCD panel.  
• When “ON” is selected, the color temperature becomes the innate temperature in the LCD panel, and the  
setting of “WHITE BALANCE SET.” becomes ineffective (page 14).  
Setting value: VIDEO, COMPO. (component)  
VIDEO/COMPO. SEL.  
Selects the signal type you want to use for the VIDEO/COMPONENT terminals.  
• When select the component (COMPO.), make sure to set the component level in “COMPO. LEVELin  
“PICTURE SUB ADJ.(page 14).  
Setting value: 4:3, 16:9  
ASPECT*  
Changes the aspect ratio of the picture.  
* Memorized for each input — composite signal input (VIDEO), component signal input (COMPO.), SDI 1 and SDI 2.  
MARKER*1  
Settings for marker functions  
1/2  
Item  
To do  
Setting value  
“NOTE”  
AREA MARKER*2  
Activate/deactivate the area marker and select the  
style of it.  
Select the aspect ratio of the area marker.  
MARKER ASPECT*2  
4:3, 14:9, 13:9, 2.35:1, 1.85:1,  
1.66:1  
SAFETY MARKER  
Activate/deactivate the safety marker and select the  
style of it.  
“NOTE”  
SAFETY AREA  
FRAME*3  
Adjust the area of the safety marker.  
Displays/hides the frame indicating the area of the  
specified aspect ratio.  
80% – 100%  
OFF, ON  
Operation guide  
Shows the buttons for each  
operation.  
CENTER MARKER  
LINE BRIGHTNESS  
Displays/hides the marker indicating the center  
position of the picture.  
Adjust the brightness of the marker.  
OFF, ON  
HIGH, LOW  
• The menu automatically disappears in about 30 seconds after the previous operation.  
• Some items may not appear on the menu depending on the input or the input signal.  
• The items controlled by the MAKE system do not appear on the menu.  
2/2  
Item  
To do  
Setting value  
“NOTE”  
R-AREA MARKER*2  
Activate/deactivate the area marker and select the  
style of it.  
R-MARKER ASPECT*2  
R-SAFETY MARKER  
R-SAFETY AREA  
Select the aspect ratio of the area marker.  
4:3, 14:9, 13:9, 2.35:1, 1.85:1,  
1.66:1  
“NOTE”  
Activate/deactivate the safety marker and select the  
style of it.  
Adjust the area of the safety marker.  
80% – 100%  
• The area marker and the safety marker is displayed by using MARKER button or external control.  
• Select either non-“R-” items or “R-” items to activate by using external control (“External Control” on page 16).  
• When a picture is displayed in 4:3 aspect ratio, the safety marker for the 4:3 area is displayed.  
To display the safety marker for the area of a picture displayed in 16:9 aspect ratio, hide the area marker.  
(“NOTE”)  
*1 Memorized for each input — composite signal input (VIDEO), component signal input (COMPO.), SDI 1 and SDI 2.  
*2 Displayed only when picture is displayed in 16:9 aspect ratio.  
*3 For signals of NTSC, B/W60, 480/60i and 480/59.94i, only the vertical borders of the frame are displayed.  
Setting value: OFF, ON  
TIME CODE  
Activates/deactivates the display of the time data (time code) contained in the SDI signal.  
(“On the Information Display” on page 7)  
NOTE  
Setting of “AREA MARKER”, “SAFETY MARKER”, “R-AREA MARKER”,  
“R-SAFETY MARKER”  
The setting values and features are as follows.  
OFF:  
Deactivate the marker.  
LINE:  
HALF:  
Displays the area with an outline.  
The area outside the specified aspect ratio of the screen is displayed at 50% transparency.  
HALF+L: The area of the specified aspect ratio of the screen is indicated by an outline, and the area  
outside of that is displayed at 50% transparency.  
BLK.:  
The area outside the specified aspect ratio of the screen is black. Only the portion of the picture  
within the designated area is displayed.  
BLK. +L: The area of the specified aspect ratio of the screen is indicated by an outline, and the area  
outside of that becomes black so that only the area inside the line is displayed.  
11  
12  
Menu Configuration—MAIN MENU (cont.)  
AUDIO SETTING  
Settings for the level meter  
Item  
To do  
Setting value  
BAR POSITION  
Select the type of the level meter display  
— vertically or horizontally.  
VERT. (vertically), HORZ. (horizontally)  
LEVEL METER ch  
CH ARRANGE  
BAR TYPE  
Select the number of the audio channels  
displayed on the level meter.  
Select the order of the audio channels  
displayed on the level meter.  
OFF, 12CH, 8CH  
LINE, DIVIDE (“NOTE”)  
Select the color of the level meter display.  
3COLORS (3 colors to indicate variations in  
input levels), W.100 (white), W.50 (half tone)  
REFERENCE LEVEL Select the standard input level indicated on the –20dB, –18dB  
Operation guide  
Shows the buttons for each  
operation.  
level meter.  
OVER LEVEL  
Select the input level’s lower limit indicated in  
red for the “3COLORS” display.  
Select the brightness of the level meter.  
–10dB, –8dB, –6dB, –4dB, –2dB  
LOW, HIGH  
BAR BRIGHTNESS  
• The menu automatically disappears in about 30 seconds after the previous operation.  
• Some items may not appear on the menu depending on the input or the input signal.  
• The items controlled by the MAKE system do not appear on the menu.  
NOTE  
Example of the level meter display—Level meter position and audio channels  
Ex.: When “LEVEL METER ch” is set to “8CH” and “BAR TYPE” is set to “3COLORS.”  
REFERENCE LEVEL  
OVER LEVEL  
REFERENCE LEVEL  
OVER LEVEL  
• When “CH ARRANGE” is set  
to “DIVIDE,odd channels are  
displayed on the left and even  
channels are displayed on the  
right.  
Green  
Green  
Red  
Red  
Yellow  
Yellow  
• When “BAR TYPE” is set  
to “W.100” or “W.50,” the  
standard input level set in  
the “REFERENCE LEVEL”  
is displayed with the line  
indication. The input level set in  
“OVER LEVELis not displayed.  
• The level meter with no signal  
input is displayed in white for  
“3COLORS,and in gray for  
“W.100” or “W.50.”  
Ex.: BAR POSITION: HORZ.,  
CH ARRANGE: LINE  
Ex.: BAR POSITION: HORZ.,  
CH ARRANGE: DIVIDE  
OVER LEVEL  
OVER LEVEL  
Red  
Yellow  
Green  
Red  
Yellow  
Green  
REFERENCE LEVEL  
REFERENCE LEVEL  
Ex.: BAR POSITION: VERT.,  
CH ARRANGE: LINE  
Ex.: BAR POSITION: VERT.,  
CH ARRANGE: DIVIDE  
WAVE FORM SETTING  
Settings for the wave form monitor  
Item  
To do  
Setting value  
POSITION  
Select the position of the wave form monitor.  
1 (lower right), 2 (lower left), 3 (upper left),  
4 (upper right)  
GAIN  
Adjust the gain level for the incoming wave form  
data.  
Select the over level for the incoming luminance  
signals.  
Activates/deactivates the function to change the  
color of a wave form when the signal exceeds the  
limit specified on “LEVEL(below).  
–10 – +10  
“NOTE”  
OFF, ON  
OVER LEVEL  
MARKING  
LEVEL  
AUTO OFF  
Adjust the lower limit for the luminance signal  
070 –109  
ON, OFF  
Activates/deactivates the function to make the  
wave form monitor indication go off automatically  
15 minutes after displaying it.  
SYNC FUNCTION  
Operation guide  
Shows the buttons for each  
operation.  
Settings for the synchronization with signals  
Item  
To do  
Setting value  
OFF,  
P.SAVE (power save mode),  
GRAY B. (gray screen)  
NO SYNC ACTION  
Select the screen status when no signal is  
coming in.  
• The menu automatically disappears in about 30 seconds after the previous operation.  
• Some items may not appear on the menu depending on the input or the input signal.  
• The items controlled by the MAKE system do not appear on the menu.  
DELAY TIME  
Select the period until the screen status  
changes as selected in “NO SYNC ACTION”  
after signals stop coming in.  
30sec., 5min., 15min.  
• When setting “NO SYNC ACTION” to “GRAY B.,” the screen color changes to gray and the power consumption  
of the back light is saved by half.  
Selecting “P.SAVE” (power save mode) saves more power consumption by turning off the back light.  
Setting value: OFF, CC1, CC2  
CLOSED CAPTION  
Selects the type of closed caption for analog composite signals (NTSC and B/W60 only).  
• Regardless of the setting, the closed caption is not displayed when the wave form monitor is displayed.  
NOTE  
Example of the wave form monitor  
Ex.: When “MARKING” is set to “ON” and “LEVELis set to “080”  
White  
Red  
• The wave which goes over the value set on “LEVEL”  
is indicated in red.  
Video signal  
Start  
End  
13  
14  
Menu Configuration—SET-UP MENU  
FUNCTION SETTING  
For the operation procedure, see page 7.  
Settings for the sub menu display, color system, color of the tally lamp, and the format indicator.  
Item  
To do  
Setting value  
“NOTE”  
sub menu POSI. Select the contents and displaying position of “sub menu.”  
COLOR  
SYSTEM  
Select the color system.  
• If the picture is unstable with “AUTO,select “NTSC” or “PAL.”  
AUTO, NTSC, PAL  
TALLY SELECT Select the color of the tally lamp.  
GREEN, RED  
FORMAT  
INDICATOR  
Select whether to use the tally lamp as the format indicator.  
OFF, ON (“NOTE”)  
• When “FORMAT INDICATOR” is set to “ON,” the TALLY function of the MAKE/TRIGGER terminal is not  
available.  
PICTURE SUB ADJ.  
Adjusts the standard level for the picture adjustment and selects the set-up level for the input video signal.  
Item  
To do  
Setting value  
–20 – +20  
Operation guide  
Shows the buttons for  
each operation.  
CONTRAST*1 Adjust the standard level for the contrast  
adjusted with CONTRAST knob on the front  
panel.  
BRIGHT*1  
CHROMA*1  
PHASE*1  
Adjust the standard level for the brightness  
adjusted with BRIGHT knob on the front panel.  
Adjust the standard level for the chroma adjusted –20 – +20  
with CHROMA knob on the front panel.  
Adjust the standard level for the phase adjusted  
with PHASE knob on the front panel.  
–20 – +20  
–20 – +20  
NTSC SETUP Select the set-up level of the input NTSC signal. 00 (compliant with 0% set-up signal), 7.5 (compliant  
with 7.5% set-up signal)  
COMPO.  
LEVEL  
Select the level of the analog component signal  
(480i and 576i only).  
B75 (compliant with BetacamVTR 7.5% set-up  
signal), B00 (compliant with BetacamVTR 0% set-  
up signal), SMPTE (compliant with M2VTR signals)  
• The menu automatically disappears in about 30 seconds after the  
previous operation.  
• Some items may not appear on the menu depending on the input or  
the input signal.  
sub menu  
Display the sub menu which enables you to adjust the items in “PICTURE SUB ADJ.while viewing the  
actual picture.  
Restore the default settings for all the items in “PICTURE SUB ADJ.”  
reset  
• The items controlled by the MAKE system do not appear on the menu.  
• When the DYNAMIC lamp lights, “PICTURE SUB ADJ.does not appear on the menu (8 on page 6).  
H. POSITION*1  
Setting value: –003 – +003  
Adjusts the horizontal picture position.  
NOTE  
WHITE BALANCE SET.  
Selects the color temperature and adjusts the drive level of each color (R/G/B).  
Settings of “sub menu POSI.”  
Item  
To do  
Setting value  
The setting values and features are as follows.  
COLOR TEMP.  
Select the color temperature.  
9300K, 6500K, USER  
MIN – 000 – MAX (in 256  
grades)  
LOWER1: Displays the current setting and adjustment bar at the lower part of the screen.  
UPPER1: Displays the current setting and adjustment bar at the upper part of the screen.  
LOWER2: Displays the current setting at the lower part of the screen.  
UPPER2: Displays the current setting at the upper part of the screen.  
R DRIVE, G DRIVE, Adjust the drive level of each color (red, green, and blue).  
B DRIVE*2  
sub menu  
Display the sub menu which enables you to adjust the items in “WHITE BALANCE SET.” while  
viewing the actual picture.  
reset  
Restore the default settings for the drive levels of the selected color temperature.  
• The adjustment bar is not displayed for some items.  
Color of the format indicator  
• When “COLOR RANGE MODE” is set to “ON,WHITE BALANCE SET.” does not appear on the menu (☞  
page 10).  
When “FORMAT INDICATOR” is set to “ON,” the tally lamp lights as follows according to the incoming video  
signal.  
*1 Memorized for each input — composite signal input (VIDEO), component signal input (COMPO.), SDI 1 and SDI 2.  
*2 Memorized for each color temperature.  
Lights in green: 720/60p, 720/59.94p, 720/50p, 1080/60i, 1080/59.94i, 1080/50i, 1035/60i, 1035/59.94i,  
1080/24psF, 1080/23.98psF, 1080/30psF, 1080/25psF, 1080/29.97psF  
Lights in red: 480/60i, 480/59.94i, 576/50i, 480/60p, 480/59.94p, 576/50p  
Lights in orange: composite signal  
• The lamp goes off when the non-compliant video signals are coming in.  
(“External Control” on pages 16, 17)  
REMOTE SETTING  
Settings for the external control  
Item  
To do  
Setting value  
TYPE SEL.  
Select the external control method for the MAKE/  
TRIGGER terminal.  
MAKE, TRIGGER, SET  
PIN1, PIN2, PIN3,  
PIN4, PIN5  
Assign the control functions to the pins of the MAKE/ TALLY SEL, SDI 1, SDI 2, VIDEO/  
TRIGGER terminal.  
COMPO., MARKER, FRAME,  
• Assign a function to each pin terminal by selecting C.MARKER, MARK.SEL, ASPECT,  
“SET” in “TYPE SEL.mentioned above. (The  
STATUS, L.METER, TIME CODE,  
functions are assigned for “PIN6” – “PIN8” and you SOURCE ID, WAVE FORM, C. C.,  
cannot change the assignment of these functions.) COLOR OFF, SCR CHECK,  
DYNAMIC, FOCUS ASSIST, COLOR  
RANGE, MUTING, – – – (no function)  
Operation guide  
Shows the buttons for  
each operation.  
INFORMATION  
Settings for the information display of the monitor  
Item  
SOURCE ID  
To do  
Setting value  
OFF, ON  
Select if the name assigned in “CHARACTER SET.” is displayed on  
the screen (“On the Information Display” on page 7).  
CHARACTER SET.  
STATUS DISPLAY  
CRC ERROR  
Assign a name to each video source as you like (10 characters at  
maximum).You can also enter a name using the RS-232C system.  
Select if the status of the current input and the setting of muting are  
displayed on the screen (“On the Status Display” on page 7).  
Select if the CRC error indication for the input HD SDI signal is displayed ON, OFF  
“NOTE”  
AUTO, OFF, ON  
on the screen (“On the Information Display” on page 7).  
SUB HOUR METER Display the hours of use (unit: hour).You can reset this item.  
• The menu automatically disappears in about 30 seconds after the previous operation.  
• Some items may not appear on the menu depending on the input or the input signal.  
• The items controlled by the MAKE system do not appear on the menu.  
MODEL  
VERSION  
HOUR METER  
Display the model name of the monitor.  
Display the version of the monitor.  
Display the total hours of use (unit: hour). This item is used for maintenance of the monitor.  
You cannot reset this item.  
Setting value: OFF, ON  
CONTROL LOCK  
Turns on (or off) the control lock function to disable the buttons on the front panel.  
• The following operations are available even when this function is activated.  
Turning on/off (on standby) the monitor  
NOTE  
– Displaying the SET-UP MENU (by pressing button while holding button) and turning “CONTROL LOCK”  
to “OFF”  
Setting of “CHARACTER SET.”  
Assign a name for each video source.  
– Operating the monitor by an external control  
If you try other operations, “ Control lock on!” appears on the screen.  
1 Change the input to one that you want to assign a video source name for.  
You cannot store different video source names for composite signal  
input (VIDEO) and component signal input (COMPO.).  
all reset  
2 Select “CHARACTER SET.”  
Restores all the settings and adjustments of the monitor to the default.  
3 Press  
buttons to select the first character.  
• Each time you press button, the character changes as follows. Press button to reverse the order.  
• “HOUR METER” and the settings done by using the adjustment knobs on the front panel will not be reset.  
• When you operate the monitor with the AC power supply, the monitor is turned off (on standby) then turned  
on automatically. When you operate the monitor with the DC 12 V power supply, the monitor is turned off (on  
standby).  
Space  
4 Press button to move the arrow to the next space.  
• The characters entered before moving the arrow are memorized.  
5 Repeat steps 3 and 4 (10 characters at maximum).  
6 Press MENU button to store the name.  
15  
16  
External Control  
Functions controlled by the MAKE/TRIGGER system  
7 About the external control  
Display  
TALLY SEL  
SDI 1  
Functions to be controlled  
Selects the color of the tally lamp.  
Changes the input to “SDI 1.”  
Changes the input to “SDI 2.”  
Opening  
Green  
Invalid  
Invalid  
Invalid  
Off  
Short-circuiting  
This monitor has two external control terminals.  
Red  
Valid  
Valid  
Valid  
On  
MAKE/TRIGGER terminal (RJ-45): The following external control systems are available.  
(1) MAKE (make contact) system: Controls the monitor by short-circuiting the corresponding pin terminal to  
the GND pin terminal, or disconnecting (opening) it (below).  
(2) TRIGGER (trigger) system: Controls the monitor by sending the pulse signal instantaneously to the  
corresponding pin terminal (below).  
SDI 2  
VIDEO/COMPO. Changes the input to “VIDEO/COMPO.”  
MARKER  
FRAME  
C.MARKER  
MARK.SEL  
ASPECT  
The area marker and the safety marker indication  
Indication of the area of the specified aspect ratio  
The center marker indication  
Selects the items of “MARKER”*4  
Changes the aspect ratio.  
Off  
Off  
On  
On  
RS-232C terminal (D-sub 9-pin): Controls the monitor with the RS-232C system. (page 17)  
Non-“R-” items  
4:3  
“R-” items  
16:9  
“On the Status Display” on page 7  
• Control priority is as follows.  
MAKE > TRIGGER, RS-232C, buttons and menu on the monitor  
You can use the external control even when “CONTROL LOCK” is set to “ON” (page 15).  
• When the monitor is off (on standby), external control is not available.  
STATUS  
Status display*5  
6
L.METER  
TIME CODE  
SOURCE ID  
WAVE FORM  
C. C.  
Audio level meter display  
Time code display  
“SOURCE ID” on page 15  
Wave form monitor display*7  
Closed caption display  
*
Off  
Off  
Off  
On  
On  
On  
7 Using the MAKE/TRIGGER system  
8
9
You can control the monitor by a personal computer or dedicated controller*1.  
*
*1 The controller is not commercially available. Consult your dealer if you need it.  
COLOR OFF  
SCR CHECK  
DYNAMIC  
Color off  
Screens check  
Adjusts the picture to be suitable for a bright place.  
Color  
Monochrome  
*
Off  
Off  
On  
On  
The MAKE/TRIGGER terminal is configured as follows.You can assign a function to each pin terminal in  
“REMOTE SETTING” (“PIN1, PIN2, PIN3, PIN4, PIN5” on page 15).  
FOCUS ASSIST Helps to focus the picture.  
COLOR RANGE Reduces the difference of the luminance level specific to  
the LCD panel.  
Pin No.  
Pin name  
PIN1  
PIN2  
PIN3  
PIN4  
Pin No.  
Pin name  
PIN5  
PIN6 (TALLY)*2  
PIN7 (ENABLE)*3  
PIN8 (GND)  
Off  
On  
This is a female  
terminal.  
1
2
3
4
5
6
7
8
MUTING  
— — —  
Muting on/off  
No function  
Off  
On  
*4 Selects which functions in “MARKER” are activated, non-“R-” items or “R-” items (page 11).  
*5 Displays the information shown when the button of the current input is pressed (“On the Status Display” on page 7).  
While controlling with the MAKE system, the information is displayed only at the moment of short-circuiting.  
*6 While controlling with the MAKE system, the level meter is switched between displayed (short-circuiting) and hidden  
(opening). When “LEVEL METER ch” is set to “OFF,” the level meter is not displayed (“NO EFFECT” appears). While  
controlling with the TRIGGER system, the number of the audio channels displayed is changed (between OFF, 12CH  
and 8CH).  
*2 The 6th pin terminal controls turning on or off the tally lamp (available to control even when the 7th pin terminal is  
invalid.)  
*3 The 7th pin terminal makes the external control valid/invalid. Make sure to control the terminal by the MAKE system.  
You cannot change the functions assigned to the pin terminals from 6th to 8th.  
• When “FORMAT INDICATOR” in “FUNCTION SETTING” is set to “ON,the TALLY lamp cannot be controlled  
by the external control (page 14)  
You cannot assign the same function to different pin terminals.  
• The TRIGGER system switches each function by short-circuiting the pin terminal for about 1 second and  
opening it.  
*7 While controlling with the MAKE system, the wave form monitor will not disappear until opening the terminal even when  
“AUTO OFF” is set to “ON.”  
*8 For analog composite signals (NTSC and B/W60 only). While controlling with the MAKE system, the closed caption  
is switched between displayed (short-circuiting) and hidden (opening). When “CLOSED CAPTION” is set to “OFF,” the  
closed caption is not displayed (“NO EFFECT” appears). While controlling with the TRIGGER system, the type of the  
closed caption can be selected.  
*9 While controlling with the MAKE system, the screen is switched between normal screen (opening) and blue screen  
(short-circuiting). While controlling with the TRIGGER system, the screen changes as follows:  
To assign the functions to the pin terminals  
For the operation procedure, see page 7.  
Normal screen  
Red screen  
1 Select “REMOTE SETTING” on the SET-UP MENU.  
2 Set “TYPE SEL.to “SET.”  
Blue screen  
Green screen  
3 Select a pin name (“PIN1” – “PIN5”) for which you want to assign a function, then select the function you want  
to assign.  
• For selectable functions, see the table on the right.  
Operation of the external control  
<Basic command list>  
No.  
1
2
Commands  
Functions  
Starts communication (connection)  
Terminates communication (termination)  
Data  
No data  
No data  
1 Set “TYPE SEL.of “REMOTE SETTING” to “MAKE” or “TRIGGER” in the SET-UP MENU.  
2 Short-circuit the 7th pin terminal (ENABLE) to the 8th pin terminal (GND) so that the monitor can be controlled  
by the external control.  
!
!
0
0
0
0
B
B
C
C
N
N
1
0
Cr  
Cr  
3 When the “MAKE” system is selected: Operate each function by short-circuiting the corresponding pin terminal  
Displays the MAIN MENU/Quits the menu  
operation  
3
!
0
0
B
M E  
N
U
Cr  
No data  
to the 8th pin terminal (GND) or opening it.  
When the “TRIGGER” system is selected: Operate each function by pulse control, that is short-circuiting the  
corresponding pin terminal to the 8th pin terminal (GND) for about 1 second and opening it.  
• When changing the input with MAKE system, only one pin terminal must be short-circuited. (Other pin terminals  
must be opened.)  
• When selecting the TRIGGER system, you can operate only one function at a time. Operate the functions one  
by one.  
4
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
U
D
A
A
S
P
P
I
P
O
D
D
E
Cr  
No data  
Moves the cursor upward (  
)
5
W N Cr  
No data  
Moves the cursor downward (  
)
6
7
8
9
J
J
T
R
L
U
Cr  
Cr  
P
Makes setting/adjustment (  
Makes setting/adjustment (  
Displays the SET-UP MENU  
Turns on the monitor  
Turns off the monitor (standby)  
Selects “SDI 1” input  
Selects “SDI 2” input  
Selects “VIDEO/COMPO.input  
Displays the status*2  
Increases the volume level  
Decrease the volume level  
Adjusts the volume level  
Turns muting on/off  
)
)
No data  
No data  
No data  
No data  
No data  
No data  
No data  
No data  
No data  
No data  
No data  
00 – 30  
00: Off, 01: On  
00: 4:3, 01: 16:9  
Cr  
W 1 Cr  
W 0 Cr  
N
N
N
I
P
M N  
O
M U  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
7 Using the RS-232C system  
A
B
C
S
L
Cr  
Cr  
Cr  
P
S
S
x
T
x
I
I
You can control the monitor from a personal computer etc. via the RS-232C terminal.  
• Consult your dealer for the details of the external control specification.  
D
V
V
V
A
A
Cr  
Cr  
Cr  
x*1 Cr  
E
<Communication specifications>  
Baud Rate: 4800 bps  
Data Bits: 8 bits  
Parity: No parity  
Stop Bits: 1 bit  
Flow Control: No control  
L
x
x*1 Cr  
S
P
x*1 Cr  
Changes the aspect ratio  
• “Cr” is 0Dh.  
Communication Code: ASCII Code  
• Use a straight cable with a D-sub 9-pin connector (male for the monitor, female for the personal computer).  
• The commands for starting communication (connection) (No. 1), terminating communication (termination)  
(No. 2), and turning on the monitor (No. 9) can be used while the monitor is off (on standby).  
<Command outline>  
All commands consist of the following segments.  
*1 Enter the appropriate data to “xx”.  
*2 Displays the information shown when the button of the current input is pressed (“On the Status Display” on page 7).  
Header  
Monitor ID (00)  
Command ID  
Function  
Data  
Cr (0Dh)  
<Specifications of the RS-232C terminal>  
Header  
“!”: Operation commands from the personal computer, etc. For details, see <Basic command list> on the right.  
“?”: Reference commands from the personal computer, etc.  
“@”: Status returns from the monitor  
Pin No.  
Signal  
NC  
1
2
3
4
5
6
7
8
9
To start communication, send the connection command from the personal computer etc.  
To terminate the communication, send the termination command from the personal computer etc.  
RXD  
TXD  
NC  
This is a female  
terminal.  
Example of communication procedures  
GND  
NC  
1 Starting the communication: connection command  
(!00BCN1Cr)  
RTS  
CTS  
NC  
2 Monitor’s status (@00BOKCr)  
Monitor  
3 Selecting “SDI 1” input (!00BINACr)  
• The 7th terminal and the 8th terminal are connected.  
4 Monitor’s status (@00BOKCr)  
PC, etc.  
5 Terminating the communication: termination command  
(!00BCN0Cr)  
6 Monitor’s status (@00BOKCr)  
17  
18  
Troubleshooting  
Solutions to common problems related to the monitor are described here. If none of the solutions presented here  
solve the problem, unplug the monitor and consult an authorized dealer or service center.  
Symptom  
Probable cause and corrective action  
Page  
Symptom  
Probable cause and corrective action  
Page  
6
8
8
8
• Adjust the picture contrast or brightness by using the adjustment  
knobs on the front panel. Or, adjust “CONTRAST” or “BRIGHT” of  
“PICTURE SUB ADJ.in the SET-UP MENU.  
6, 14  
• Press the  
button.  
The picture becomes  
blurred.  
Turn on the POWER switch or DC switch on the rear panel.  
• Firmly insert the AC power plug or DC 12 V power plug.  
• When using a DC 12 V power supply, charge the battery or replace it  
with a charged one.  
No power supply  
• Check whether the input signal format is acceptable on the monitor.  
• Check the setting of “ASPECT” in the MAIN MENU.  
7, 9  
10  
Wrong picture position, • Adjust the horizontal picture position in “H. POSITION” of the SET-  
14  
• Select the correct input.  
• Connect the signal cable firmly.  
6
8
wrong picture size.  
UP MENU.  
No picture with the  
power on  
• For some signals, the picture cannot be displayed fully in the  
effective screen area. There is no sure method to solve this problem.  
Turn on the power of the connected component and set the output  
correctly.  
• Check whether the input signal format is acceptable on the monitor.  
9
• The items which are not available for the current input or the current  
input signal are not displayed on the menu. Change the input or the  
input signal.  
• The items controlled by the MAKE system do not appear on the  
menu.  
• Adjust the volume level.  
6
6
8
Some items do not  
appear on the menu.  
• Deactivate the muting function.  
• Connect the signal cable firmly.  
Turn on the power of the connected component and set the output  
correctly.  
16  
No sound  
• Set “CONTROL LOCK” in the SET-UP MENU to “OFF.”  
You cannot use the buttons for the items controlled by the MAKE  
system. Disable the external control.  
15  
16  
Buttons on the monitor  
do not work.  
“OTHERS” or “Out of  
range” appears.  
• Check whether the input signal format is acceptable on the monitor.  
7, 9  
• Select the correct input.  
• Connect the signal cable firmly.  
6
8
“NO SYNC” appears.  
Turn on the power of the connected component and output video  
signals. Or, check whether the video output of the component (video  
output setting of the VCR) is set correctly.  
• Adjust each picture adjustment knob on the front panel or adjust the  
items of “PICTURE SUB ADJ.in the SET-UP MENU. Or, perform  
“reset” in “PICTURE SUB ADJ.”  
6, 14  
• Check if the screen mode is other than normal screen, by using SCR.  
CHK. button.  
6
Wrong color, no color  
• Select the proper color system (“COLOR SYSTEM”) in “FUNCTION  
SETTING” of the SET-UP MENU.  
• Adjust the items of “WHITE BALANCE SET.” in the SET-UP MENU.  
Or, perform “reset” in “WHITE BALANCE SET.”  
14  
14  
The following are not malfunctions.  
• When a still image is displayed for a long time, it may remain indistinctly on the screen after the picture has  
changed. Though the remaining picture will disappear after a while, there may be a case that it remains  
for a long period depending on the length of time the still image was displayed for. This is due to the  
characteristics of the LCD display and is not a malfunction.  
• Red spots, blue spots and green spots on the panel surface are a normal characteristic of LCD displays,  
and not a problem. The LCD display is built with very high precision technology; however, be aware that a  
few pixels may be missing or constantly lit.  
• The following symptoms are problems only when pictures or sounds are not played back normally.  
– A slight electric shock occurs when you touch the monitor.  
– The top and/or rear panel of the monitor becomes hot.  
– The monitor emits a cracking noise.  
– The monitor emits a mechanical noise.  
7 Self-check program  
This monitor has a self-check function, which allows it to detect malfunctions and alert you. This makes  
troubleshooting easier. Whenever a problem occurs, one or some of the self-check lamps will flash. If this  
happens, follow the steps below and contact your dealer to resolve the problem.  
When the screen goes blank and one or some of the self-check lamps on the front control panel start  
flashing...  
1 Check which lamps are flashing.  
2 Press  
button to turn off (on standby) the monitor.  
3 Turn off the POWER switch and DC switch on the rear panel.  
4
When the AC power supply is used: Disconnect the AC power cord from the AC outlet.  
When a DC 12 V power supply is used: Detach the battery or disconnect the plug  
from the DC IN terminal.  
5 Contact your dealer with the information about which lamps were flashing.  
• If you turn on the monitor soon after turning it off (or after a short-term power failure), the self-check lamps may  
flash and no image may be displayed. When this happens, turn off power and wait at least 10 seconds before  
turning on the monitor again. If the self-check lamps do not flash, you can use the monitor as normal.  
19  
20  
Maintenance  
Unplug this product from the wall outlet before cleaning.  
Screen  
To avoid irreparable change in appearance of the screen such as uneven color, discoloration, scratches, be  
careful about the following:  
• Do not paste or stick anything using any glues or adhesive tapes.  
• Do not write anything on the screen.  
• Do not strike the screen with a hard object.  
• Avoid condensation on the screen.  
• Do not wipe the screen with solvent such as alcohol, thinner, or benzine.  
• Do not wipe the screen forcefully.  
Wipe stains off the screen with a soft cloth. If the screen gets heavily stained, wipe it with a soft cloth soaked in  
water-diluted neutral detergent and wrung well, then wipe with a soft dry cloth.  
Cabinet  
To avoid the deterioration or damages of the cabinet such as its paint’s peeling away, be careful about the  
following:  
• Do not wipe the cabinet using solvent such as alcohol, thinner, or benzine.  
• Do not expose the cabinet to any volatile substance such as insecticides.  
• Do not allow any rubber or plastic in contact for a long time.  
• Do not wipe the cabinet forcefully.  
Wipe stains off the cabinet with a soft cloth. If the cabinet gets heavily stained, wipe it with a soft cloth soaked in  
water-diluted neutral detergent and wrung well, then wipe with a soft dry cloth.  
Ventilation openings  
Use a vacuum cleaner to get rid of the dust around the intakes (all the openings). If a vacuum cleaner is not  
available, use a cloth and wipe it off. Leaving the dust around the intakes may prevent proper temperature control  
and cause damage to the product.  
Specifications  
7 General  
7 Input/output terminals  
Model name  
Type  
DT-V9L3DY  
VBS/Y  
Composite signal/analog component (Y) signal input/output:  
1 line, BNC connector x 2  
Multi format LCD monitor  
Type 9 wide format  
15:9  
Screen size  
Aspect ratio  
LCD panel  
1 V(p-p), 75 Ω  
VIDEO/COMPONENT  
(IN/OUT)  
* The input (IN) and output (OUT) terminals are bridge-  
connected (auto termination)  
PB, PR  
9˝ wide, IPS-Pro  
Width: 195 mm (7 5/8˝)  
Height: 117 mm (4 9/16˝)  
Effective screen size  
Analog component (PB, PR) signal input:  
1 line, BNC connector x 2  
Number of pixels displayed  
Number of colors displayed  
Viewing angle (TYP.)  
Brightness  
800 x 480  
0.7 V(p-p), 75 Ω  
16.77 million  
E. AUDIO HD/SD SDI (IN 1)  
E. AUDIO HD/SD SDI (IN 2)  
Digital signal input (compatible with EMBEDDED AUDIO signals):  
auto detection, 1 line, BNC connector x 1  
170° (Horizontally), 170° (Vertically)  
350 cd/m2  
E. AUDIO HD/SD SDI  
(SWITCHED OUT)  
Digital signal output (compatible with EMBEDDED AUDIO signals):  
1 line switched out, BNC connector x 1  
Contrast ratio (TYP.)  
400:1  
Compliant video signal format  
“Available signals” on page 9  
AUDIO (IN)  
Analog audio signal input:  
1 line, RCA connector x 1,  
500 mV (rms), high impedance  
HD SDI: BTA S-004B, SMPTE292M  
SD SDI: ITU-R BT.656: 525/625  
SMPTE259M: 525  
Format  
AUDIO (MONITOR OUT)  
EARPHONE  
Analog audio signal output: 1 line, RCA connector x 2,  
500 mV (rms)  
EMBEDDED AUDIO: SMPTE299M, SMPTE272M  
Audio output  
Internal speaker: 1.0 W  
Monaural mini jack (3.5 mm in diameter) x 1  
Operating temperature: 0°C – 40°C (32°F – 104°F)  
Operating humidity: 20 % – 80 % (non-condensing)  
* Slightly variable depending on ambient conditions for installation.  
REMOTE (MAKE/  
TRIGGER)  
“Using the MAKE/TRIGGER system” on page 16  
Operating conditions  
REMOTE (RS-232C)  
“Using the RS-232C system” on page 17  
AC 120 V, 50 Hz/60 Hz  
DC 12 – 17 V  
Power requirements  
Rated current  
0.35 A (AC 120 V)  
1.7 A (DC 12 – 17 V)  
Width:  
222.4 mm (8 7/8˝)  
Height: 218 mm (8 5/8˝) (at the higher position),  
181 mm (7 1/4˝) (at the lower position),  
176 mm (7˝) (without stand)  
External dimensions  
(excluding protruding parts)  
Depth:  
185 mm (7 3/8˝) (at the higher position),  
202 mm (8˝) (at the lower position),  
116 mm (4 5/8˝) (without stand)  
3.6 kg (7.9 lbs) (with the stand)  
2.7 kg (5.9 lbs) (without the stand)  
Weight  
Notice on transportation  
This monitor is precision equipment and needs dedicated packing material for transportation.  
Never use any packing material supplied from sources other than JVC or JVC-authorized dealers.  
AC power cord x 1, Power cord holder x 1, Screw x 2 (for power cord holder),  
Protective filter x 1, Screw (for protective filter) x 4  
Accessories  
• For easy understanding, pictures and illustrations are shown by being emphasized, omitted or composed,  
and may be slightly different from actual products.  
• Design and specifications are subject to change without notice.  
Use the Anton Bauer Dionic 90 (mount: QR DXC-M3A) external battery.  
• All company names and product names mentioned herein are used for identification purposes only, and  
may be the trademarks or registered trademarks of their respective companies.  
CAUTION  
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.  
21  
22  
Specifications (cont.)  
Unit: mm (inch)  
7 Dimensions  
<Front view>  
<Side view>  
<Rear view>  
• When the stand is attached to the  
higher position.  
• When the stand is attached to the  
lower position.  
116 (4 5/8)  
27.5 (1 1/8)  
VESA mounting holes  
(8-M4, depth: 10 mm)  
100  
75  
1.5 (1/16)  
222.4 (8 7/8)  
202 (8)  
13 (5/8)  
186 (7 3/8)  
185 (7 3/8)  
* at the higher position  
** at the lower position  
tapped hole (3/8˝)  
tapped hole (1/4˝)  
DT-V9L3DY MULTI FORMAT LCD MONITOR  
© 2009 Victor Company of Japan, Limited  
0809TKH-MW-MT  

IBM THINKVISION L170 User Manual
KitchenAid KBMC140 KBMC147 KEMC308 KEMC378 KEMC307 KEMC377 YKEMC307 YKEMC308 User Manual
Lenovo 3658 User Manual
LG Electronics LG Life Good Computer Monitor E2060T User Manual
NEC 75F 95F User Manual
Panasonic BT LH1760 User Manual
Panasonic TX 1703MA User Manual
Panasonic WJ NT314 User Manual
Philips 220V3 User Manual
Philips PDCC LL 0815 User Manual