Color Television Users Guide
For Models:
AV-32F577
AV-27F577
AV-32WF47
AV-32MF47
AV-27MF47
Illustration of AV-32F577 and RM-C1290G
Important Note:
In the spaces below, enter the model and serial number of your television (located
at the rear of the television cabinet). Staple your sales receipt or invoice to the
inside cover of this guide. Keep this user’s guide in a convenient place for future
reference. Keep the carton and original packaging for future use.
Model Number:
LCT2033-001A-A
0206TNH-II-IM
Serial Number:
®
• As an “ENERGY STAR ” partner,
JVC has determined that this
product or product model meets the
®
“ENERGY STAR ” guidelines for energy
efficiency.
Important Safeguards
CAUTION:
Please read and retain for your safety.
Electrical energy can perform many useful functions. This TV set has been engineered and
manufactured to assure your personal safety. But improper use can result in potential
electrical shock or fire hazards. In order not to defeat the safeguards incorporated in this
TV set, observe the following basic rules for its installation, use and servicing. Also follow all
warnings and instructions marked on your TV set.
INSTALLATION
(POLARIZED-TYPE)
1 Your TV set is equipped with a polarized AC line plug (one
blade of the plug is wider than the other). This safety feature
allows the plug to fit into the power outlet only one way.
Should you be unable to insert the plug fully into the outlet,
try reversing the plug. Should it still fail to fit, contact your
electrician.
2 Operate the TV set only from a power source as indicated on the TV set or refer to the
operating instructions for this information. If you are not sure of the type of power supply to
your home, consult your TV set dealer or local power company. For battery operation, refer
to the operating instructions.
3 Overloaded AC outlets and extension cords are dangerous, and so are frayed power cords
and broken plugs. They may result in a shock or fire hazard. Call your service technician for
replacement.
4 Do not allow anything to rest on or roll over the power cord, and do not place the TV set
where power cord is subject to traffic or abuse. This may result in a shock or fire hazard.
5 Do not use this TV set near water — for example, near a bathtub, washbowl, kitchen sink, or
laundry tub, in a wet basement, or near swimming pool, etc.
6 If an outside antenna is connected to the TV set, be sure the antenna system is grounded
so as to provide some protection against voltage surges and built-up static charges.
Section 810 of the National Electrical Code provides information with respect to proper
grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna
discharge unit, size of grounding conductors, location of antenna discharge unit, connection
requirements for the grounding electrode.
3
7 An outside antenna system should not be located in the vicinity of overhead power lines
or other electric light or power circuits, or where it can fall into such power lines or circuits.
When installing an outside antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them might be fatal.
EXAMPLE OF ANTENNA GROUNDING
AS PER NATIONAL ELECTRICAL CODE
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRICAL
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ARTICLE 250, PART H)
NEC - NATIONAL ELECTRIC CODE
8 TV sets are provided with ventilation openings in the cabinet to allow heat generated during
operation to be released.
Therefore:
— Never block the bottom ventilation slots of a portable TV set by placing it on a bed, sofa,
rug, etc.
— Never place a TV set in a “built-in” enclosure unless proper ventilation is provided.
— Never cover the openings with a cloth or other material.
— Never place the TV set near or over a radiator or heat register.
9 To avoid personal injury:
— Do not place a TV set on a sloping shelf unless properly secured.
— Use only a cart or stand recommended by the TV set manufacturer.
— Do not try to roll a cart with small casters across thresholds or deep pile carpets.
— Wall or shelf mounting should follow the manufacturer’s instructions, and should use a
mounting kit approved by the manufacturer.
Use
10 Caution children about dropping or pushing objects into the TV set through cabinet
openings. Some internal parts carry hazardous voltages and contact can result in a fire or
electrical shock.
11 Unplug the TV set from the wall outlet before cleaning. Do not use liquid or an aerosol
cleaner.
12 Never add accessories to a TV set that has not been designed for this purpose. Such
additions may result in a hazard.
4
PORTABLE CART WARNING
(Symbol provided by RETAC)
13 For added protection of the TV set during a lightning storm or when the TV set is to be left
unattended for an extended period of time, unplug it from the wall outlet and disconnect the
antenna. This will prevent damage to product due to lightning storms or power line surges.
14 A TV set and cart combination should be moved with care. Quick stops, excessive force,
and uneven surfaces may cause the TV set and cart combination to overturn.
Service
15 Unplug this TV set from the wall outlet and refer servicing to qualified service personnel
under the following conditions:
A. When the power cord or plug is damaged or frayed.
B. If liquid has been spilled into the TV set.
C. If the TV set has been exposed to rain or water.
D. If the TV set does not operate normally by following the operating instructions. Adjust
only those controls that are covered in the operating instructions as improper adjustment
of other controls may result in damage and will often require extensive work by a
qualified technician to restore the TV set to normal operation.
E. If the TV set has been dropped or damaged in any way.
F. When the TV set exhibits a distinct change in performance — this indicates a need for
service.
16 Do not attempt to service this TV set yourself as opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
17 When replacement parts are required, have the service technician verify in writing that the
replacement parts he uses have the same safety characteristics as the original parts. Use
of manufacturer’s specified replacement parts can prevent fire, shock, or other hazards.
18 Upon completion of any service or repairs to this TV set, please ask the service technician
to perform the safety check described in the manufacturer’s service literature.
19 When a TV set reaches the end of its useful life, improper disposal could result in a picture
tube implosion. Ask a qualified service technician to dispose of the TV set.
20 Note to CATV system installer.
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of
the NEC that provides guidelines for proper grounding and, in particular, specifies that the
cable ground shall be connected to the grounding system of the building, as close to the
point of cable entry as practical.
5
Table of Contents
Quick Setup . . . . . . . . . . . . . 7
Unpacking your TV . . . . . . . . . . . . 7
TV Models . . . . . . . . . . . . . . . . 8
TV Remote Control . . . . . . . . . . . 9
Getting Started . . . . . . . . . . . . . 10
The Remote Control . . . . . . . . . . 10
Connecting Your Devices . . . . . . . 11
Interactive Plug In Menu . . . . . . . . 16
Button Functions . . . . . . . . . 43
Power . . . . . . . . . . . . . . . . . . 43
Number Buttons . . . . . . . . . . . . . 43
Tune . . . . . . . . . . . . . . . . . . 43
Input . . . . . . . . . . . . . . . . . . . 43
Channel +/- . . . . . . . . . . . . . . 43
Volume +/- . . . . . . . . . . . . . . . 43
Return+/TV . . . . . . . . . . . . . . . 44
Sound . . . . . . . . . . . . . . . . . . 44
Muting . . . . . . . . . . . . . . . . . . 44
Video Status . . . . . . . . . . . . . . . 45
TheaterPro D6500K . . . . . . . . . . . 45
Sleep Timer . . . . . . . . . . . . . . . 45
Display . . . . . . . . . . . . . . . . . 46
C.C. . . . . . . . . . . . . . . . . . . . 46
Aspect . . . . . . . . . . . . . . . . . 47
Aspect Ratios . . . . . . . . . . . . . 47
Favorite . . . . . . . . . . . . . . . . . . . 49
ML/MTS . . . . . . . . . . . . . . . . . . . 50
Menu . . . . . . . . . . . . . . . . . . 50
OK . . . . . . . . . . . . . . . . . . . 50
Back . . . . . . . . . . . . . . . . . . . 50
DVD Buttons . . . . . . . . . . . . . . . 51
Sub Channel . . . . . . . . . . . . . 51
Guide . . . . . . . . . . . . . . . 51
Game . . . . . . . . . . . . . . . 51
Onscreen Menus . . . . . . . . . . 19
Using the Guide . . . . . . . . . . . . . 19
Onscreen Menu System . . . . . . . . . 20
Initial Setup . . . . . . . . . . . . 22
Noise Muting . . . . . . . . . . . . 22
Language
.
.
.
.
.
.
.
.
.
.
.
.
22
Front Panel Lock . . . . . . . . . . . . 22
V-Chip . . . . . . . . . . . . . . . . . . 23
Closed Caption . . . . . . . . . . . . . 30
Auto Shut Off . . . . . . . . . . . . . . 32
Software Version . . . . . . . . . . . 32
Tuner Setup . . . . . . . . . . . 33
Auto Tuner Setup . . . . . . . . . . . 33
Channel Summary . . . . . . . . . . . 33
Find Channel . . . . . . . . . . . . . . 34
Digital Antenna Level . . . . . . . . . . 35
Troubleshooting . . . . . . . . . 52
Specifications . . . . . . . . . . 53
Warranty . . . . . . . . . . . . . 54
Authorized Service Centers . . 55
External Input . . . . . . . . . . . 36
Video Input Label . . . . . . . . . . . 36
Picture Adjust . . . . . . . . . . . 37
Picture Settings . . . . . . . . . . . . . 37
Adjust Picture Settings . . . . . . . . . 37
Color Temperature . . . . . . . . . . . . 37
VSM . . . . . . . . . . . . . . . . . . . 38
Reset . . . . . . . . . . . . . . . . . . 38
Sound Adjust . . . . . . . . . . . 39
Sound Settings . . . . . . . . . . . . . 39
Adjust Sound Settings . . . . . . . 39
Optical Out . . . . . . . . . . . . . . 39
Turn On Volume . . . . . . . . . . . . . 40
Volume Limit . . . . . . . . . . . . . . . 40
Reset . . . . . . . . . . . . . . . . . . 40
Clock Timers . . . . . . . . . . . 41
Set Clock . . . . . . . . . . . . . . . . 41
On/Off Timer . . . . . . . . . . . . . . . 42
6
Quick Setup
Unpacking your TV
Thank you for your purchase of a JVC Color Television. Before you begin setting up your new
television, please check to make sure you have all of the following items. In addition to this
guide, your television box should include:
Two AA
Batteries
1 Remote Control
1 Television
Note: Your television
and/or remote
control may differ
from the examples
illustrated here.
We recommend that before you start using your new television, you read your entire User’s
Guide so you can learn about your new television’s many great features. If you’re anxious to
start using your television right away, a quick setup guide follows on the next few pages.
7
Quick Setup
TV Models
Before you connect your television to another device, please refer to the proper diagrams for
your specific TV and remote. These will help assist you in understanding how to connect your
television to another device, as well as use the remote to set up your television.
Rear panel diagram
AUDIO
L /MONO
VIDEO
S-VIDEO
R
OVER
INPUT-1
Pr
Pb
Pb
Y
Y
SERVICE
ONLY
COMPONENT
VIDEO
VIDEO/Pr
COMPONENT
VIDEO
AUDIO
INPUT-2
R
L/MONO
75Ω
(VHF/UHF)
L
R
Manufactured under license
from Dolby Laboratories.
“Dolby” and the double-D
symbol are trademarks of
Dolby Laboratories.
OPTICAL OUT
DIGITAL
AUDIO
AUDIO OUT
Notes:
• The terminal labeled "SERVICE ONLY", is exclusively used to update the software version.
• There is the component Y/Pb/Pr terminal on INPUT-1 only for AV-32WF47.
Front panel diagram
INPUT
3
VOLUME
CHANNEL
OPERATE
MENU
VIDEO
L
MONO
AUDIO
R
8
Quick Setup
Remote Control
RM-C1290G
• For information on remote control buttons, see pages 43 - 51.
• DVD CONTROL can only be used with JVC-brand DVDs.
9
Quick Setup
Getting Started
Getting Started
These quick setup pages will provide you, in three easy steps, with the basic information you
need to begin using your new television right away. If you have questions, or for more detailed
information on any of these steps, please consult other sections of this manual.
Step 1 – The Remote Control
Before you can operate your remote control, you first need to
install the batteries (included).
Raise the latch on the remote's back cover to remove. Insert
two batteries, carefully noting the "+" and "–" markings, and
place the "–" end in the remote first. Snap the cover back into
place.
Key Feature Buttons
The four key feature buttons at the center of the remote
can be used for basic operation of the television. The top
and bottom buttons will scan forward and back through the
available channels. To move rapidly through the channels
using JVC’s Hyperscan feature, press and hold CH+
or CH–. The channels will zip by at a rate of about four
channels per second. The right and left buttons will turn
the volume up or down. These buttons are also marked
with four arrows and are used with JVC’s onscreen menu
system. To use the onscreen menus, press the MENU
button.
Basic Operation
Turn the television on and off by pressing the POWER button at the top right
corner of the remote. If this is the first time you are turning on the TV, the
interactive plug-in menu appears.
10
Connections
Quick Setup
Step 2 – Connecting Your Devices
To make these connections, you will use plugs like the ones illustrated below.
Component Cables
Coaxial Cables
Composite Cables
Audio Cables
Used to connect an external
antenna or cable TV system to your
TV.
Used to connect audio/video
devices like VCRs, DVD players,
stereo amplifiers, game consoles,
etc.
S-Video Cable
Used to make video connections
with S-Video VCRs, Camcorders
and DVD players.
Notes:
• These connections are examples.
• After you are finished connecting your devices, plug the power cord into the nearest power
outlet and turn on the TV.
• If you follow these diagrams and the television does not work properly, contact your local
cable operator.
• To connect a DVD player, see VCR Connection. A DVD player is optional
• If you have a satellite television system, refer to the satellite TV manual.
No VCR Connection
Cable or Antenna
Coaxial Cable
Output
TV Rear Panel
75Ω
(VHF/UHF)
11
Quick Setup
Connections
VCR Connection
Notes:
• Green, blue and red are the most common colors for DVD cables. Some models may vary
colors. Please consult the user’s manual for your DVD player for more information.
• Be careful not to confuse the red DVD cable with the red audio cable. It is best to complete
one set of connections (DVD or audio output) before starting the other to avoid accidentally
switching the cables.
• You may also connect the DVD player to Input 1.
Diagram #1
VCR
R
L
V
Cable or Antenna
Output
Cable Cable
In Out
IN
OUT
Coaxial Cable
OR
AUDIO
L /MNO
VO
S-VEO
75Ω
(VHF/UHF)
OVER
INPUT-1
Pr
Pb
Y
Y
COMPONENT
VIDEO
TV Rear Panel
VIDEO/Pr
Pb
COMPONENT
VIDEO
AU
INPUT-2
R
L/MO
L
AUDIO OUT
DVD Player (Optional)
AUO UT
VEO OUT
PR PB
Y
R
L
Note:
• If this connection setup does not work for you, try the connection setup on page 13.
12
Connections
Quick Setup
Diagram #2
VCR
R
L
V
Cable or Antenna
Output
Cable Cable
In Out
IN
OUT
IN
Two-Way Splitter
OR
OUT OUT
AUDIO
L /MNO
VO
S-VEO
OVER
INPUT-1
Pr
Pb
Y
Y
Coaxial Cable
COMPONENT
VIDEO
VIDEO/Pr
Pb
COMPONENT
VIDEO
75Ω
(VHF/UHF)
AU
INPUT-2
R
L/MO
L
TV Rear Panel
AUDIO OUT
DVD Player (Optional)
AUO UT
VEO OUT
PR PB
Y
R
L
13
Quick Setup
Connections
Connecting to a Camcorder
You may connect a camcorder, game console or other equipment to your television by using
the front input jacks (Input 3) located under the front panel door. To access, push on the door
to open it. You can also connect these using the television’s rear input jacks, using the same
instructions.
INPUT
3
CHANNEL
OPERATE
VOLUME
MENU
VO
L
NO
O
R
Camcorder
1) Connect a yellow composite cable from the camcorder VIDEO OUT, into the VIDEO IN on
the front of the TV.
2) Connect a white composite cable from the camcorder LEFT AUDIO OUT, into the
LEFT AUDIO IN on the front of the TV.
3) Connect a red composite cable from the camcorder RIGHT AUDIO OUT, into the
RIGHT AUDIO IN on the front of the TV.
Note:
• If your camcorder is a mono sound model it will have only one AUDIO OUT. Connect it to the
LEFT AUDIO IN.
Connecting to an External Amplifier
TV Rear Panel
Speaker
Speaker
Amplifier
R
L
UDIO
1) Connect a white composite cable from the LEFT AUDIO OUTPUT on the back of the TV to
the LEFT AUDIO INPUT on the amplifier.
2) Connect a red composite cable from the RIGHT AUDIO OUTPUT on the back of the TV to
the RIGHT AUDIO INPUT on the amplifier.
Notes:
• Refer to your amplifier’s manual for more information.
• You can use AUDIO OUTPUT for your home theater system.
14
Connections
Quick Setup
Connecting to an amplifier using your optical output
You can connect an amplifier that has an optical digital input terminal by using an optical digital
cable from the optical output. The signal that is output can be PCM or Dolby Digital.
TV Rear Panel
OPTIOUT
DAL
AO
Amplifier
1) Connect the optical cable from the back of the TV to the back of the amplifier.
Notes:
• This terminal can only output digital audio.
• In order to use the optical output connection, select "PCM" or "Dolby Digital" on "Optical Out"
in Sound Adjust. See page 39.
• Refer to your owners manual on using your amplifier.
15
Quick Setup
Plug-In Menu
Step 3 – The Interactive Plug In Menu
The interactive plug-in menu appears only for AV-27F577, AV-32F577 and AV-32WF47. If
your television is one of the other models, we recommend you complete the Auto Tuner
Setup to begin watching your television right away. See pages 22, 41 and 33.
When you turn your television on for the first time the interactive plug-in menu will appear. The
plug-in menu helps you to get your TV ready to use by letting you set your preferences for:
• The language in which you want the onscreen menus to appear.
• Setting the TV’s clock to the correct time so your timer functions will work properly. You can
choose “Auto” or “Manual” for setting the clock.
• The auto tuner setup of which channels you wish to receive.
We recommend you complete the interactive plug-in items before you start using your
television.
Note:
• If you press the MENU button while setting up the interactive plug-in menu, it will skip over it.
Language
After the “JVC Interactive Plug-in Menu” has been displayed, the TV automatically switches
to the "Language" settings. You can choose to view your onscreen menus in three languages:
English, French (Français) or Spanish (Español).
è
To choose a language:
(English, Français or Español)
Language/Langue/Idioma
English
†
To "Set"
Press the OK button
Once you press OK, you will move to the
"Set Clock" Plug-In Menu automatically.
Set
OK
MENU
Select
Operate
Exit
(To be continued...)
16
Plug-In Menu
Quick Setup
Auto Clock Set
Before you use any of your TV’s timer functions, you must first set the clock. You may
precisely set your clock using the XDS time signal broadcast by most public analog
broadcasting stations. If you do not have this in your area, you will have to set the clock
manually. See manual clock set below. To set the clock using the XDS signal:
è
†
To choose "Auto"
To "Time Zone"
Set Clock
Mode
Auto
: 30 AM
è
To select your time zone: (Atlantic, Eastern,
Central, Mountain, Pacific, Alaska or
Hawaii)
Time
10
Time Zone
D.S.T.
Atlantic
On
†
è
†
To move to "D.S.T." (Daylight Savings Time)
To turn "On or Off"
To "set"
Set
Back
MENU
Select
Operate
Back
Exit
Press the OK button
Once you press OK, you will move to
the "Auto Tuner Setup" Plug-In Menu
automatically.
Notes:
• D.S.T. can be used when it is set to "On" in the "Set Clock" menu.
• Only when the "Mode" is set to "Auto", the Daylight Savings Time feature automatically
adjusts your TV’s clock for Daylight Savings. The clock will move forward one hour at 2:00
am on the first Sunday in April. The clock will move back one hour at 2:00 am on the last
Sunday in October.
• You will have to reset the clock after a power interruption. You must set the clock before
operating any timer functions.
Manual Clock Set
To set your clock manually (without using the XDS signal), choose "Manual". If you choose
"Auto", see auto clock set above.
è
†
To choose "Manual"
To "Time"
Set Clock
è
†
è
†
To set the hour
To minute
To set the minute
To "Time Zone"
Mode
Manual
Time
10
:
30 AM
Time Zone
D.S.T.
Atlantic
On
Set
è
To select your time zone: (Atlantic, Eastern,
Central, Mountain, Pacific, Alaska or
Hawaii)
Back
MENU
Select
Operate
Back
Exit
†
è
†
To move to "D.S.T." (Daylight Savings Time)
To turn "On or Off"
To "Set"
Press the OK button
Once you press OK, you will move to
the "Auto Tuner Setup" Plug-In Menu
automatically.
Note:
• You will have to reset the clock after a power interruption. You must set the clock before
operating any timer functions.
(To be continued...)
17
Quick Setup
Plug-In Menu
Auto Tuner Setup
In auto tuner setup, the TV automatically scans through all available channels, memorizing the
active ones and skipping over blank ones or channels with weak signals. This means when you
scan (using the CHANNEL +/– buttons) you will receive only clear, active channels.
è
To choose "Cable or "Air" (or "Skip" when
you skip "Auto Tuner Setup")
Auto Tuner Setup
Tuner Mode
Scan Mode
Air
†
To "Start"
Auto
Press the OK button
Start
Back
OK
Back
MENU
Select
Operate
Exit
Now programming ...
20
When the setup is finished, "Thank you ! Setup is now complete." is displayed. Your quick
setup is now complete. You can now begin watching your television, or you can continue
on in this guide for more information on programming your remote control, or using the
JVC onscreen menu system to customize your television viewing experience.
Notes:
• If you want to cancel the Auto Tuner Setup, press the MENU button.
• Noise muting will not work during Auto Tuner Setup.
• If you choose "Skip", it finished without doing the Auto Tuner Setup.
Cable Box and Satellite Users: After your auto tuner setup is complete, you may, (depending
on the type of hookup), have only 1 channel, usually 3 or 4 in the auto tuner memory. This is
normal.
The Quick Setup is complete
STOP
18
Onscreen Menus
Using the Guide
Certain symbols are used throughout this guide to help you learn about the features of your
new television. The ones you will see most frequently are:
π† Up and Down arrows mean press the CH+ or CH– buttons. Pressing the CH+ or CH–
buttons let you:
• Move vertically in a main menu screen
• Move through a submenu screen
• Move to the next letter, number, or other choice in a submenu
• Back up to correct an error
• Scan through TV channels (when not in a menu screen)
è Left and right arrows mean press the VOLUME+ or VOLUMEРbuttons to move left or right
to:
• Select a highlighted menu item
• Select an item in a submenu
• Select numbers in certain menu options
• Turn the volume up or down (when not in a menu screen)
The “press button” icon means you should press the button named on your remote
control. (Button names appear in SMALL CAPITAL LETTERS.)
The “helping arrow” icon points to the highlighted or selected item in a menu.
To bring up the onscreen menu, press the MENU button on the remote control. The following
(left) main menu will appear. The item that appears in green is the one currently selected. If
you use the MENU button on the TV’s front panel instead of the remote, Front Menu screen
showing "Input", "Video Status", "Aspect" and "Menu" will appear (following right screen).
The “interactive plug-in menu” will appear the first time the TV is plugged in (AV-27F577,
AV-32F577 and AV-32WF47 ONLY).
Front Menu
Menu
TV
Standard
4:3
Input
Initial Setup
Video Status
Aspect
–
+
Tuner Setup
Menu
External Input
Picture Adjust
Sound Adjust
Exit
Clock/Timers
MENU
Select
Operate
Interactive Plug-in Menu
Note:
• Menus shown in this book are illustrations, not exact replications of the television’s onscreen
displays.
19
Onscreen Menus
The Onscreen Menu System
Your television comes with JVC’s onscreen menu system. The onscreen menus let you make
adjustments to your television’s operation simply and quickly. All menus are navigated from
the Main Menu at first. Detailed explanations on using each menu follow later in this guide. For
information about the interactive plug-in Menu, see pages 16 - 18. (AV-27F577, AV-32F577
and AV-32WF47 ONLY).
1. To open the onscreen menu system, press the MENU button on the remote control. The
main menu will appear
Menu
Initial Setup
–
+
Tuner Setup
External Input
Picture Adjust
Sound Adjust
Clock/Timers
Interactive Plug-in Menu
2. To select a menu from the main menu, use the π†arrows and enter by using the √®
arrows or OK button. See page 21.
The selected feature and option on a menu screen are highlighted in a different color.
To move to a different feature, use the π†arrows to move up and down the list.
3. There are two methods to select an option in a menu, after selecting a menu using the π†
arrows.
1) Use the è arrows to select an option from the highlighted feature. (In this guide, we
discuss this method).
–
+
Auto Tuner Setup
2) Press the OK button. The right onscreen will
appear. Use the π†arrows to select an option
from the box and press the OK button.
Tuner Mode
Scan Mode
Cable
Auto
Auto
STD
HRC
IRC
• To go back to the previous screen, press the BACK
button.
Sta
Back
4. Pressing MENU on the remote control will close the
onscreen menu system and return you to normal
television viewing.
OK
Back
MENU
Select
Operate
Exit
Each menu and its features will be discussed in the following pages of this guide.
Notes:
• If you do not press any buttons for a few seconds, the onscreen menu will automatically
shut off.
• Button names in this guide are shown in SMALL CAPITAL LETTERS.
• Menus may appear in different sizes onscreen depending on the aspect ratio selected.
• Some menu items may not appear in menu screens when certain aspect ratios or inputs
are selected.
20
Onscreen Menus
Initial Setup
1/2
Initial Setup
2/2
From the
Noise Muting
Language
On
English
Off
Auto Shut Off
On
Main Menu...
Software Version
Front Panel Lock
V-Chip
Set Lock Code
Closed Caption
Back
MENU
Back
MENU
Select
Operate
Back
Exit
Select
Operate
Back
Exit
Initial Setup 1/2
Initial Setup 2/2
–
+
Tuner Setup
Auto Tuner Setup
Channel Summary
Find Channel
Digital Antenna Level
Back
MENU
Select
Operate
Back
Exit
Tuner Setup
External Input
Video Input Label
Back
MENU
Select
Operate
Back
Exit
External Input
Picture Adjust
1/2
Picture Adjust
2/2
Video Status
Video Status
Standard
Standard
Tint
0
0
0
0
0
VSM
On
Color
Reset
Picture
Bright
Detail
Color Temperature
Low
Back
MENU
Back
MENU
Select
Operate
Back
Exit
Select
Operate
Back
Exit
Picture Adjust 1/2
Picture Adjust 2/2
Sound Adjust
Bass
0
0
0
Treble
Balance
Optical Out
Turn On Volume
Volume Limit
PCM
Current
20
Reset
Back
Back
MENU
Select
Operate
Exit
Sound Adjust
Clock/Timers
Set Clock
On / Off Timer
Back
MENU
Select
Operate
Back
Exit
Clock/Timers
• For the Interactive Plug-In Menu, see page 16.
• "Video Input Label" is only for models AV-27F577 and AV-32F577.
If your TV is model AV-27MF47, AV-32MF47 or AV-32WF47, "External Input" menu screen will
not be displayed.
21
Initial Setup
Noise Muting
This feature inserts a blank gray screen over channels which are not broadcasting or are too
weak to be received clearly.
Initial Setup
1/2
Press the MENU button
Noise Muting
Language
On
English
Off
π†
è
π†
è
To "Initial Setup"
To enter
To "Noise Muting"
To turn "On" or "Off"
Press the MENU button when finished
Front Panel Lock
V-Chip
Set Lock Code
Closed Caption
Back
MENU
Select
Operate
Back
Exit
Note:
• Noise muting will not work during auto tuner setup or when you operate channel summary.
• Noise muting will not work when the digital TV is displayed.
Language
The language function is described on page 16 as the interactive plug-in menu (AV-27F577,
AV-32F577 and AV-32WF47 ONLY). If you need to choose the language again, follow the
steps below.
Initial Setup
1/2
Press the MENU button
Noise Muting
Language
On
English
Off
π†
è
π†
To "Initial Setup"
To enter
Front Panel Lock
V-Chip
Set Lock Code
Closed Caption
To "Language"
è
To choose a language: English, Français or
Español
Back
MENU
Select
Operate
Back
Exit
Press the MENU button when finished
Front Panel Lock
This allows you to lock the keys on the front of the TV, so that a child may not accidentally
change your viewing preferences.
Press the MENU button
Initial Setup
1/2
Noise Muting
Language
On
English
Off
π†
è
π†
è
To "Initial Setup"
To enter
To "Front Panel Lock"
To turn "On" or "Off"
Press the MENU button when finished
Front Panel Lock
V-Chip
Set Lock Code
Closed Caption
Back
MENU
Select
Operate
Back
Exit
You can turn off this feature in the following ways:
• Unplug the power cord, and plug it back in. Do this if your batteries die, or you lose your
remote control.
• Use the remote control.
• Press the MENU button on the front of the TV for more than 3 seconds. In this case, the OSD
for "Front Panel Lock" will appear.
Note:
• To turn ON/OFF the TV, press the POWER button for more than 3 seconds. This feature will
remain ON.
22
Initial Setup
V-Chip
Your TV is equipped with V-Chip technology which enables you to block channels or content
that you feel to be inappropriate for children, based on US and Canada rating guidelines.
V-Chip has no effect on video signals from a DVD discs, VCR tapes or Camcorder connection.
Note: Some programs, and movies are broadcast without a ratings signal. Even if you set
up V-CHIP ratings limits, these programs will not be blocked. See page 28 for information on
how to block unrated programs.
Note (for Canadian viewers): The V-Chip function is based on specifications designed for
the United States and therefore may not work properly in Canada.
You can customize the V-Chip settings of your television to match your personal tastes. The
V-Chip menu below is the starting point for your V-Chip settings
You can use US V-Chip settings (for programming broadcast from the United States), Canadian
V-Chip settings (for programming broadcast from Canada), and movie ratings. You may use
any or all of the settings (US V-Chip, Canada V-Chip, Movie ratings). Descriptions for setting
each of the three V-Chip formats appear in the next six pages along with descriptions of the
rating categories.
To access the rating categories:
Initial Setup > V-Chip
Press the MENU button
V-Chip
Off
π†
è
π†
è
To "Initial Setup"
To enter
To "V-Chip"
To operate (Password input screen will
appear)
Set US TV Ratings
Set Movie Ratings
Set Canadian Ratings English
Set Canadian Ratings French
Unrated
View
Back
MENU
Select
Operate
Back
Exit
Enter the password by using the 10 button
keypad
The V-Chip main screen will appear when the password is correct.
è
To turn V-Chip "On" or "Off" (V-Chip must be turned "On" for rating settings to
operate)
π†
To move to V-Chip menu (see following pages for descriptions of each item)
Notes:
• If you input the wrong password, go back to the initial Setup Menu.
• To set the password, see "Set Lock Code", page 29.
• "Advanced V-Chip Rating" and "Advanced Canadian Rating" menus may be displayed
sometimes between "Set Canadian Ratings French" and "Unrated". These menus are
reserved for future use, as of February 2006.
23
Initial Setup
US V-Chip Ratings
U.S. PARENTAL RATING SYSTEMS
Programs with the following ratings are appropriate for children.
❒ TV Y is Appropriate for All Children
Programs are created for very young viewers and should be suitable for all ages, including
children ages 2 - 6.
❒ TV Y7 is for Older Children
Most parents would find such programs suitable for children 7 and above. These programs
may contain some mild fantasy violence or comedic violence, which children should be able
to discern from reality.
Programs with the following ratings are designed for the entire audience.
❒ TV G stands for General Audience
Most parents would find these programs suitable for all age groups. They contain little or no
violence, no strong language, and little or no sexual dialog or situations.
❒ TV PG Parental Guidance Suggested
May contain some, but not much, strong language, limited violence, and some suggestive
sexual dialog or situations. It is recommended that parents watch these programs first, or
with their children.
❒ TV 14 Parents Strongly Cautioned
Programs contain some material that may be unsuitable for children under the age of 14
including possible intense violence, sexual situations, strong coarse language, or intensely
suggestive dialog. Parents are cautioned against unattended viewing by children under 14.
❒ TV MA Mature Audiences Only
These programs are specifically for adults and may be unsuitable for anyone under 17
years of age. TV MA programs may have extensive V, S, L, or D.
Viewing Guidelines
In addition to the ratings categories explained above, information on specific kinds of content
are also supplied with the V-Chip rating. These types of content may also be blocked. The
content types are:
• V/FV is for VIOLENCE/FANTASY VIOLENCE
• S stands for SEXUAL CONTENT
• L stands for strong LANGUAGE
• D stands for suggestive DIALOG
24
Initial Setup
Setting US V-Chip Ratings
Press the MENU button
Initial Setup > V-Chip
π†
è
π†
è
To "Initial Setup"
To enter
To "V-Chip"
To operate (Password input screen will
appear)
V-Chip
On
Set US TV Ratings
Set Movie Ratings
Set Canadian Ratings English
Set Canadian Ratings French
Unrated
View
Enter the password by using the 10 button
keypad
Back
MENU
Select
Operate
Back
Exit
The V-Chip main screen will appear
è
π†
è
To turn V-Chip "On" or "Off"
To move to "Set US TV Ratings"
To operate
Directions to set US V-Chip Ratings
Line up the cursor in the column (TV PG, TV G, etc.) with the content row (V/FV, S, etc.) and
press the π† or √® to move the cursor to the correct location. Press OK to turn the locking
feature on or off. An item is locked if the
icon appears instead of a “—”.
For example. To block viewing of all TV 14 shows, move the cursor to the top row of that
column and add a lock icon. Once you’ve put a lock on the top row, everything in that column
is automatically locked.
π†√® To the TV 14 Column
Set US TV Ratings
TV
MA
TV
14
TV
PG
TV
G
TV
Y7
TV
Y
Press the OK button to lock
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
Press the MENU button when finished
V/FV
S
L
Note:
D
• If you want to change the setup, move the cursor to
the top column and change the lock icon to “—” by
pressing OK again. You may then select individual
categories to block.
OK
Back
MENU
Select
Operate
Back
Exit
25
Initial Setup
Movies Ratings
❒ NR – Not Rated
This is a film which has no rating. In many cases these films were imported from countries
which do not use the MPAA ratings system. Other NR films may be from amateur producers
who didn’t intend to have their film widely released.
NR (Not Rated) Programming may contain all types of programming including children’s
programming, foreign programs, or adult material.
❒ G – General Audience
In the opinion of the review board, these films contain nothing in the way of sexual content,
violence, or language that would be unsuitable for audiences of any age.
❒ PG – Parental Guidance
Parental Guidance means the movie may contain some contents such as mild violence,
some brief nudity, and strong language. The contents are not deemed intense.
❒
PG-13 – Parents Strongly Cautioned
Parents with children under 13 are cautioned that the content of movies with this rating may
include more explicit sexual, language, and violence content than movies rated PG.
❒ R – Restricted
These films contain material that is explicit in nature and is not recommended for
unsupervised children under the age of 17.
❒ NC-17 – No One Under 17
These movies contain content which most parents would feel is too adult for their children
to view. Content can consist of strong language, nudity, violence, and suggestive or explicit
subject matter.
❒ X – No One under 18
Inappropriate material for anyone under 18.
Directions to set Movie (MPAA) Ratings
Press the MENU button
π†
è
π†
è
To "Initial Setup"
To enter
To "V-Chip"
To operate (Password input screen will appear)
Enter the password by using the 10 button keypad
The V-Chip main screen will appear
To turn V-Chip "On" or "Off"
è
π†
è
To "Set Movie Ratings"
To enter movies menu
For example:
To block viewing of X and NC-17 rated from shows:
Set US Movie Ratings
è
To the X Column
NC
17
PG
Press the OK button to lock
To the NC-17 Column
X
R
_
PG
_
G
_
NR
_
13
_
_
è
Press the OK button to lock
Press the MENU button to finish
OK
Back
MENU
Select
Operate
Back
Exit
26
Initial Setup
Canadian V-Chip Ratings
❒ E – Exempt
Exempt programming includes: news, sports, documentaries and other information
programming, talk shows, music videos, and variety programming.
❒ C – Programming Intended for Children
Violence Guidelines: There will be no realistic scenes of violence. Depictions of aggressive
behavior will be infrequent and limited to portrayals that are clearly imaginary, comedic or
unrealistic in nature.
❒ C8+ – Programming Intended for Children 8 and Over
Violence Guidelines: Any realistic depictions of violence will be infrequent, discreet, of low
intensity and will show the consequences of the acts. There will be no offensive language,
nudity or sexual content.
❒ G – General Audience
Programming will contain little violence and will be sensitive to themes which could affect
younger children.
❒ PG – Parental Guidance
Programming intended for a general audience, but which may not be suitable for younger
children. Parents may consider some content not appropriate for children aged 8-13.
❒ 14+ – 14 Years and Older
Parents are strongly cautioned to exercise discretion in permitting viewing by pre-teens and
early teens. Programming may contain mature themes and scenes of intense violence.
❒ 18+ – Adult
Material intended for mature audiences only.
Directions to set Canadian V-Chip Ratings
Press the MENU button
π†
è
π†
è
To "Initial Setup"
To enter
To "V-Chip"
To operate (Password input screen will appear)
Enter the password by using the 10 button keypad
The V-Chip main screen will appear
To turn V-Chip "On" or "Off"
è
π†
è
Set Canadian Ratings English
To "Set Canadian Ratings English"
To enter ratings menu
18+
_
14+
_
PG
_
G
_
C8+
_
C
_
For example:
To block viewing of programming rated 14+ and 18+:
è
To the 18+ Column
Press the OK button to lock
To the 14+ Column
OK
Back
MENU
Select
Operate
Back
Exit
è
Press the OK button to lock
Press the MENU button to finish
27
Initial Setup
Unrated Programs
Unrated programming refers to any programming which does not contain a rating signal.
Programming on television stations which do not broadcast rating signals will be placed in the
“Unrated Programming” category.
Examples of Unrated programs:
• Emergency Bulletins
• News
• Public Service Announcements
• Sports
• Locally Originated Programming
• Political Programs
• Religious Programs
• Weather
• Some Commercials
Note:
• TV programs or movies that do not have rating signals will be blocked if the unrated category
is set to "Block".
Directions to Block Unrated Programs
You can block programs that are not rated.
Press the MENU button
Initial Setup > V-Chip
π†
è
π†
è
To "Initial Setup"
To enter
To "V-Chip"
V-Chip
On
Set US TV Ratings
Set Movie Ratings
Set Canadian Ratings English
Set Canadian Ratings French
Unrated
To operate (Password input screen will appear)
View
Enter the password by using the 10 button
keypad
Back
MENU
Select
Operate
Back
Exit
The V-Chip main screen will appear
è
π†
è
To turn V-Chip "On" or "Off"
To "Unrated"
To "View" or "Block"
Press MENU when done
28
Initial Setup
Set Lock Code
Channel guard and V-Chip settings are protected by a four-digit lock code. Your TV comes pre-
set with a lock code of “0000”. You may change the code to any four-digit number you wish. To
change the lock code, follow the steps below.
Press the MENU button
Initial Setup > Set Lock Code
π†
è
π†
è
To "Initial Setup"
To enter
To "Set Lock Code"
To operate (Password input screen will appear)
Lock Code
0
1
2
3
Enter the password by using the 10 button
keypad
Set
Clear
OK
Back
MENU
Select
Operate
Back
Exit
The Set Lock Code screen will appear
To set the password, use the 10 button keypad
Press the OK button to finish (your lock code is now set)
When a viewer attempts to watch a blocked channel,
this message appears:
This programming exceeds
your rating limits.
Please enter lock code by
10 key pad to unlock it.
The channel will remain blocked until the correct lock
code is entered (see above for information on setting
your lock code).
No. - - - -
Notes:
• After a power interruption you must reset the lock code.
• Write your lock code number down and keep it hidden from potential viewers.
• If you forget the lock code, a new code may be set using the steps listed above.
Channel Guard Message
When a viewer attempts to watch a guarded channel, the following message appears:
To watch a channel that you have locked, enter the
Lock Code using the 10 key pad.
If the wrong code is entered, the message "invalid lock
code !” will flash on the screen.
This channel is locked by
channel guard.
Please enter lock code by
10 key pad to unlock it.
The channel cannot be accessed until the correct code
is entered.
No. - - - -
Notes:
• Once a channel has been unlocked, it will remain unlocked until the television is turned off.
• See also “Set Lock Code”, page 29.
29
Initial Setup
Closed Caption
Many broadcasts now include an onscreen display of dialog called closed captions. Some
broadcasts may also include displays of additional information in text form. Your television can
access and display this information using the closed caption feature. To activate the closed
caption feature, follow the steps below.
Auto Setting
Press the MENU button
Initial Setup > Closed Caption
Preview
π†
è
π†
è
π†
è
To "Initial Setup"
To enter
To "Closed Caption"
To enter
To "Type"
To select Auto, Advanced or Basic
Closed Caption sample
Type
Auto
Text1
1
Analog Service
Digital Service
Appearance
Reset
Back
Back
MENU
Select
Operate
Exit
Auto: Shows closed caption a priority for
digital channels over analog channels. It is set automatically.
Advanced: Shows only the digital closed caption.
Basic: Shows only the analog closed caption.
π†
è
π†
è
π†
è
è
To "Analog Service"
To select a caption (CC1 to CC4) or text channel (Text1 to Text4)
To "Digital Service"
To select 1, 2, 3, 4, 5 or 6
To Appearance
To enter
To select "Auto" ("Manual", see page 32)
Press the MENU button when finished
Notes:
• If you want to reset your settings to the default settings, select "Reset".
• If you select "Advanced" for Type, you cannot select "Analog Service".
• If you select "Basic" for Type, you cannot select "Digital Service" and "Appearance".
30
Initial Setup
Manual Setting
è
To select "Manual" for Appearance
Initial Setup > Closed Caption > Appearance 1/2
Preview
π†
To "Font Size", "Font Style", "Text/Edge
Opacity", "Background Opacity", "Text Color",
"Edge Color" or "Backgrond Color".
Closed Caption sample
Appearance Mode
Font Size
Manual
Standard
Auto
Font Style
Text / Edge Opacity
Background Opacity
Solid
Solid
è
To select the setting you like
Back
MENU
Select
Operate
Back
Exit
Font Size: Auto, Standard, Large or Small
Font Style: Auto, SerifMono, Serif, SanSerifMono,
SanSerif, Casual, Cursive or SmallCapital
Initial Setup > Closed Caption > Appearance 2/2
Preview
Text/Edge Opacity, Background Opacity: Auto,
Closed Caption sample
Transparent, Translucent, Solid, Flashing.
Text Color
White
White
Black
Edge Color
Text Color, Edge Color, Background Color: Auto,
White, Black, Red, Green, Blue, Yellow, Magenta, or
Cyan
Background Color
Back
MENU
Select
Operate
Back
Exit
Press the MENU button when finished
All fonts used for digital closed
caption and digital menus are
licensed from Monotype Imaging
Inc.
Notes:
• Closed caption subtitles are usually found on closed caption channel CC1. Some programs
may include additional text information which is usually found on text channel T1. The other
channels are available for future use.
• Closed captioning may not work correctly if the signal being received is weak or if you are
playing a video tape.
• Most broadcasts containing closed captioning will display a notice at the start of the program.
• To select the mode, press the C.C. button. See page 46.
31
Initial Setup
Auto Shut Off
This function automatically shuts off your TV when there is no signal from the channel the
TV is on.
Press the MENU button
Initial Setup
2/2
π†
è
π†
è
To "Initial Setup"
To enter
To "Auto Shut Off"
To turn "On" or "Off"
Auto Shut Off
On
Software Version
Press the MENU button when finished
Back
MENU
Select
Operate
Back
Exit
• If the channel that you have on does not receive a
signal for more than one minute, the blinking text “No
Program or Weak Signal Auto shut off in 9 min.” appears on the screen, and starts the
countdown. If no signal is being received within 10 minutes, the TV shuts itself off.
Software Version
You can confirm the Software Version.
Press the MENU button
π†
è
To "Initial Setup"
To enter
π†
è
è
To "Software Version"
To enter
Select close when you are finished confirming your software version
Press the MENU button when finished
32
Tuner Setup
Auto Tuner Setup
The auto tuner setup function is described on page 18 as the interactive plug-in menu
(AV-27F577, AV-32F577 and AV-32WF47 ONLY). If you need to run the auto tuner setup
again, follow the steps below.
–
+
Auto Tuner Setup
Press the MENU button
Tuner Mode
Scan Mode
Cable
Auto
π†
è
π†
è
è
π†
è
†
To "Initial Setup"
To enter
To "Auto Tuner Setup"
To enter
To choose "Cable" or "Air"
To "Scan Mode"
To choose "Auto", "STD", "HRC" or "IRC"
To "Start"
Start
Back
Back
MENU
Select
Operate
Exit
Press the OK button (Programming will take serveral minutes)
The auto tuner is finished when the message "Programming Over !" appears onscreen.
Press the MENU button when finished
Notes:
• When the Tuner Mode is set to "Cable", it is possible to select "Scan Mode"
• If no channels were found using Auto Tuner Setup, check your antenna cable and the
settings for Tuner Mode/Scan Mode.
Channel Summary
Channel summary allows you to customize the line-up of channels received by your TV.
Regarding analog channels, you can add or delete channels from the line-up or prevent any
unauthorized viewers from watching any or all 191 channels. Regarding digital channels, the
only channels that will appear are the ones that are broadcasting.
Press the MENU button
π†
è
π†
è
To "Initial Setup"
To enter
To "Channel Summary"
To operate
–
+
Tuner Setup > Channel Summary
Ch No.
001
Scan
Station
FOX
002
003
004
005
006
ABC
CNN
NBC
BOX
NHK
The Channel summary screen will now be displayed with
the channels set to scan marked with an “√”. Regarding
analog channels, you can delete channels from the scan
by removing the “√”. If any channels were missed during
auto tuner setup and you wish to add them, you may by
placing an “√” next to the channel number.
OK
Back
MENU
Select
Operate
Back
Exit
• Digital channels can not be added to the channel summary if the auto tuner setup did not
find them.
π†√® To the "Scan" column
Press the OK button to include or delete from scan
Press the MENU button when finished
Note:
• The number of a digital channel may change, depending on the time of some broadcastings.
If this channel existed and now had disappeared, the lock channel or scanned channel by the
channel summary for that channel will be cancelled.
33
Tuner Setup
How to set the channel station.
Press the MENU button
–
+
Tuner Setup > Channel Summary > Station
π†
è
π†
è
π†
To "Initial Setup"
To enter
To "Channel Summary"
To operate
A
B
C
Channel 10
Set
Reset
Back
To "Station"
Press the OK button to enter
Back
MENU
Select
Operate
Exit
è
π†
To select the character you want
To move to the next space
...continue to follow these directions for all seven spaces
To "Set"
†
Press the OK button
Your characters are now set
Press the MENU button when finished
If you want to reset the characters you set:
Press the MENU button
π†
è
π†
è
π†
To "Initial Setup"
To enter
To "Channel Summary"
To operate
To "Station"
Press the OK button to enter
To select "Reset"
π†
Press the OK button to finish
Your characters are now reset
Notes:
• You can use characters for: Alphabet, numbers, marks and spaces.
• It is possible to set the maximum of 500 channel labels.
• If you try to set more than the 500 maximum, the message "Memory Overflow" will appear.
You can block access to a channel by activating the channel lock.
Press the MENU button
π†
è
π†
è
To "Initial Setup"
To enter
To "Channel Summary"
To operate
π†√® To the Lock Column (
)
Press the OK button to lock or unlock that channel
Press the MENU button when finished
34
Tuner Setup
Find Channel
Add a channel that does not exist in the channel map.
–
+
Press the MENU button
Tuner Setup
π†
è
π†
è
To "Tuner Setup"
To enter
To "Find Channel"
To enter
Auto Tuner Setup
Channel Summary
Find Channel
Find Channel
Digital Antenn
Channel Num.
123_
Add
Cancel
Add a channel using 0 to 9
0
9
OK
Back
MENU
†
To "Add"
.
.
.
Select
Operate
Back
Exit
Press the OK button to finish
Digital Antenna Level
Confirms the present antenna level.
Antenna Level
Press the MENU button
80
π†
To "Tuner Setup"
To enter
Back
MENU
è
Back
Exit
π†
To "Digital Antenna Level"
To enter
è
Note:
• If you are watching an analog channel, antenna level will not appear.
35
External Input
Video Input Label
(AV-27F577 and AV-32F577 ONLY). This function is used to label video input connections for
the onscreen displays.
External Input
Press the MENU button
Video Input Label
π†
è
π†
To "External Input"
To enter
To "Video Input Label"
è
π†
è
To operate
To select the desired video input
Back
MENU
Select
Operate
Back
Exit
To select the desired preset input label (see
chart below)
External Input
Press the OK button to save
Video-1
Video-2
Video-3
VCR
Press the MENU button when finished
DVD
SAT
Set
Back
MENU
Select
Operate
Back
Exit
Preset
Labels
Select when...
VCR
DVD
PVR
You have a VCR connected to the video input
You have a DVD connected to the video input
You have a Personal Video recorder connected to the video input
D-VHS You have a Digital VCR connected to the video input
STB
SAT
AMP
You have a Set-top Box connected to the video input
You have a Satellite Receiver connected to the video input
You have an Amplifier connected to the video input
GAME You have a Video Game connected to the video input
CAM
DISC
You have a Video Camera connected to the video input
You have a Video Disc player connected to the video input
36
Picture Adjust
Picture Settings
These settings allow you to change and adjust the way the picture appears on your television.
Tint
Tint allows you to adjust the levels of red and green in your TV picture.
Color
The color function lets you make all the colors in the TV picture appear either more vivid or
subtle.
Picture
Picture allows you to adjust the levels of black and white on the TV screen, giving you a darker
or brighter picture overall.
Bright
You can adjust the overall brightness of the TV picture with the Bright control.
Detail
The Detail feature adjusts the level of fine detail displayed in the picture.
Adjust the Picture Settings
Press the MENU button
Picture Adjust
1/2
π†
è
π†
√ ®
To "Picture Adjust"
To enter
To "Tint", "Color", "Picture", "Bright" or "Detail"
To enter
Video Status
Standard
0
0
0
0
0
Tint
Color
Picture
Bright
Tint
Detail
0
Color Temperature
Low
Back
MENU
Select
Operate
Back
Exit
√ ®
π†
To adjust the setting
To move to the next setting
Press the MENU button when finished
Color Temperature
You can decide how strong or dull the colors appear on the TV screen.
Press the MENU button
Color Temp.
π†
è
π†
è
π†
To "Picture Adjust"
To enter
To "Color Temperature"
To enter
Low
High
To set "Low" or "High"
Press the MENU button when finished
37
Picture Adjust
(VSM) Velocity Scan Modulation
Velocity scan modulation circuitry varies the electron beam’s horizontal scanning speed to help
accentuate the differences in picture brightness to sharpen the edges of images.
Press the MENU button
VSM
π†
è
π†
è
π†
To "Picture Adjust"
To enter
To "VSM"
To enter
To turn VSM ON or OFF
On
Off
Press the MENU button when finished
Reset
Reset resets all picture adjustments at once to the default settings.
Press the MENU button
Picture Adjust
2/2
π†
è
π†
To "Picture Adjust"
To enter
To "Reset"
Video Status
Standard
On
VSM
Reset
Press the OK button
The onscreen menu disappears for a moment,
and then the settings are reset to the default
setting for all the picture adjustments.
Back
MENU
Select
Operate
Back
Exit
Press the MENU button when finished
38
Sound Adjust
Sound Settings
These settings allow you to change and adjust the sound on your television.
Bass – You can increase or decrease the level of low-frequency sound in the TV’s audio with
the bass adjustment.
Treble – Use treble to adjust the level of high-frequency sound in your TV’s audio.
Balance – Adjust the level of sound between the TV’s left and right speakers with the balance
setting.
Adjust the Sound Settings
Press the MENU button
Sound Adjust
Bass
0
0
0
π†
è
π†
√ ®
π†
To "Sound Adjust"
To enter
To "Bass", "Treble" or "Balance"
To adjust the setting
To move to the next setting
Treble
Balance
Optical Out
Turn On Volume
Volume Limit
PCM
Current
20
Reset
Back
Back
MENU
Press the MENU button when finished
Select
Operate
Exit
Notes:
• You can reset all sound adjustments you set at once as the default setting when you select
reset. See page 38.
Optical Out
You can select the optical digital sound output, either PCM or Dolby Digital when your TV is
connected to an amplifier that has Dolby Digital decoder. If you select Dolby Digital, you can
enjoy listening in 5.1ch sound when watching digital broadcasts.
Sound Adjust
Press the MENU button
Bass
0
0
0
π†
è
To "Sound Adjust"
To enter
Treble
Balance
Optical Out
Turn On Volume
Volume Limit
PCM
Current
30
π†
To "Optical Out"
è
To select "PCM" or "DOLBY DIGITAL"
Press the MENU button when finished
Reset
Back
MENU
Select
Operate
Back
Exit
Notes:
• If your amplifier does not have Dolby Digital decoder, select PCM. If you don't select PCM, it
cannot output the sound from the speakers.
• For connecting an amplifier using the optical output, see page 15.
Manufactured under license from Dolby Laboratories. "Dolby", and
the double-D symbol are trademarks of Dolby Laboratories.
39
Sound Adjust
Turn On Volume
Turn On Volume allows you to set the volume level when you turn the TV on.
Press the MENU button
Sound Adjust
π†
è
π†
è
To "Sound Adjust"
To enter
To "Turn On Volume"
To set the maximum volume level
Bass
0
0
0
Treble
Balance
Optical Out
Turn On Volume
Volume Limit
PCM
Current
30
Current
0
1
2
3
48
49
50
Reset
Back
MENU
Select
Operate
Back
Exit
Press the MENU button to finish
Volume Limit
Volume Limit allows you to set the maximum volume level.
Press the MENU button
Sound Adjust
Bass
0
0
0
π†
è
π†
è
To "Sound Adjust"
To enter
To "Volume Limit"
To set the maximum volume level
Treble
Balance
Optical Out
Turn On Volume
Volume Limit
PCM
Current
30
0
1
2
3
48
49
50
Reset
Back
Back
MENU
Select
Operate
Exit
Press the MENU button to finish
Reset
Reset resets all Sound Adjustments at once to the default settings. See page 38 on how to use
reset.
Sound Adjust
Bass
0
0
0
Treble
Balance
Optical Out
Turn On Volume
Volume Limit
PCM
Current
30
Reset
Back
Back
MENU
Select
Operate
Exit
40
Clock/Timers
Set Clock
The set clock function is described on page 17 as the interactive plug-in menu (AV-27F577,
AV-32F577 and AV-32WF47 ONLY). You can choose to set the clock automatically, or
manually. If you need to set the clock again, follow the steps below.
Press the MENU button
π†
è
π†
è
To "Clock/Timers"
To enter
To "Set Clock"
To operate
When you set the clock automatically, choose "Auto" by pressing the
√
or
®
arrows.
π†
è
To Time Zone
To select your time zone
Clock/Timers > Set Clock
Mode
Auto
: 30 AM
Time
10
Atlantic
Eastern
Central
Mountain
Time Zone
D.S.T.
Atlantic
On
Hawaii
Alaska
Pacific
Start Clcok
π†
è
†
To D.S.T. (daylight savings time)
To turn D.S.T. On or Off
To "Start Clock"
Back
MENU
Select
Operate
Back
Exit
Press the OK button
Press the MENU button when finished
When you set the clock manually, choose "Manual" by pressing the
√
or
®
arrows.
π†
è
π†
è
π†
è
To move to the hour
To set the hour
To move to minutes
To set the minutes
To Time Zone
Clock/Timers > Set Clock
Mode
Manual
Time
10
:
30 AM
Time Zone
D.S.T.
Atlantic
On
To select your time zone:
Start Clcok
(Atlantic, Eastern, Central, Mountain, Pacific, Alaska or
Hawaii)
Back
MENU
Select
Operate
Back
Exit
π†
è
†
To D.S.T. (daylight savings time)
To turn D.S.T. On or Off
To "Start Clock"
Press the OK button
"Thank you !!" will be displayed.
Press the MENU button when finished
Notes:
• D.S.T. can be used only for US and Canada when it is set to "On" in the "Set Clock" menu.
• Only when the "Mode" set to "Auto", the Daylight Savings Time feature automatically adjusts
your TV’s clock for Daylight Savings. The clock will move forward one hour at 2:00 am on
the first Sunday in April. The clock will move back one hour at 2:00 am on the last Sunday in
October.
• You will have to reset the clock after a power interruption. You must set the clock before
operating any timer functions.
41
Clock/Timers
On/Off Timer
The on/off timer lets you program your television to turn itself on or off. You can use it as an
alarm to wake up, to help you remember important programs, or as a decoy when you’re not
home.
Clock/Timers > On / Off Timer
Press the MENU button
On Time
10
11
:
:
30 AM
30 AM
3
Off Time
Channel
π†
è
π†
è
è
†
To "Clock/Timers"
On Volume
Mode
Current
Once
To enter
On / Off Timer
Yes
To "On/Off Timer"
Set
To operate (begins with "On Time")
To set the hour (AM/PM) you want the TV to turn on
To move to minutes
Back
MENU
Select
Operate
Back
Exit
è
†
To set the minutes
To accept "On Time" and move to "Off Time" (the time the TV will turn off). Set the
"Off Time" the same way as "On Time"
†
è
†
To accept "Off Time" and move to "Channel"
To select channel
To "On Volume"
è
†
To set the volume level
To move to "Mode"
è
Choose "Once" or "Everyday"
†
è
†
To "On/Off Timer"
Choose "Yes" to accept the timer setting, choose "No" if you don’t wish to accept
To "Set"
Press the OK button
Press the MENU button to exit the menu
Notes:
• The on/off time cannot be set to locked or guarded channels.
• In order for the on/off timer to work, the clock must be set.
• After a power interruption, the timer settings must be reset.
• If your clock is not set, "Please set clock first !!" will appear on the screen. Please see
Manual Set Clock on page 41 to set the clock.
42
Button Functions
Power
Turns the TV on or off.
Press the POWER button
Number Buttons - 10Key Pad
Use the number buttons on the remote control to move directly to a specific channel. For
example, to move to channel 12:
0 (ZERO)
1 (ONE)
2 (TWO)
Tune
Lets you decide the input channel and select it. After you press the number buttons on the
remote, press the TUNE button. For example, to move to channel 12:
1 (ONE)
2 (TWO)
Press the TUNE button
Input
Selects the signal input source for the television: Input-1, 2 or 3 for video devices like VCR’s
DVD players, or camcorders.
Press the INPUT 1, 2 or 3 button
Notes:
• When you return to TV mode, press the RETURN+/TV button or direct 10 key pad.
• You can also access the "Front Menu" screen by using the MENU button on the front of
the TV instead of the remote control. It has "Input", "Video Status" and "Aspect" menus.
Choose "Input" by pressing Menu
†
®
on the front panel and choose a mode by using the
).
CHANNEL+/- buttons (
√
OPERATE
Channel +/–
Use these buttons to move up or down all the available channels your TV is able to receive,
and navigate in the menus.
Volume +/–
Use these buttons to raise or lower the TV’s volume level, and navigate in the menus.
43
Button Functions
Return +/TV
The Return+/TV button has two functions:
Return - Returns to the channel viewed just before the channel currently onscreen.
Return+ - Lets you program a specific channel to return to while scanning through the
channels using the CH+ and CH– buttons.
RETURN+/TV and hold for three seconds
Return Channel
Programmed !
The channel currently active has been programmed as your return+ channel. Now scan
through the channels using the CHANNEL+/- buttons.
RETURN+/TV
You will return to your programmed channel.
• To cancel your return+ channel, press and hold the RETURN+/TV button for three seconds.
The message “RETURN CHANNEL CANCELLED!” will appear.
• Return+ works only with the CHANNEL+/- buttons. Pressing any number key will cancel
return+.
Sound
By pressing the SOUND button, you can change the A.H.S. (Advanced Hyper Surround), BBE
and SMART SOUND on or off.
A.H.S. - Adds a more spacious surround sound. Music gives basic effect and movie for more
effect.
BBE - BBE High Definition Sound restores clarity and presence for better speech intelligibility
and musical realism.
Smart Sound - Decreases high sound levels, giving a regulated sound level.
Press the SOUND button
Sound Effect
A.H.S
Off
Off
On
π†
è
To select "A.H.S.", "BBE" or "Smart Sound"
To choose the setting
BBE
Smart Sound
Press the MENU when finished
OK
MENU
Select
Operate
Exit
Note:
• A.H.S. is for AV-27F577 and AV-32F577 ONLY.
• BBE is for AV-32WF47 ONLY.
Manufactured under license from BBE Sound, Inc. Licensed by BBE Sound, Inc. under
USP4638258, 5510752 and 5736897. BBE and BBE symbol are registered trademarks of
BBE Sound, Inc.
Muting
The MUTING button instantly turns the volume down completely when you press it. Press
MUTING and the volume level will instantly go to zero. To restore the volume to its previous
level, press MUTING again.
44
Button Functions
Video Status
The Video Status button gives you a choice of four TV picture display settings, including a
display of your own preferences.
Standard - Resets the picture display to the factory settings.
Video Status
Dynamic - Gives a vivid picture with better contrast when viewing in
Standard
a brightly lit room.
Dynamic
Theater - Gives a rich, film-like look to video when viewing in a
Theater
Game
dimly lit room.
Game - Used for when you are playing video games connected to
your TV.
Press the V. STATUS (Video Status) button
By every press of the V. STATUS button, you change the mode.
Note:
• You can also change the mode by pressing the π† buttons.
• You can also access the "Front Menu" screen by using the MENU button on the front of
the TV instead of the remote control. It has "Input", "Video Status" and "Aspect" menus.
Choose "Video Status" by pressing Menu
†
).
on the front panel and choose a mode by using
the CHANNEL+/- buttons (
√
OPERATE
®
TheaterPro D6500K
The TheaterPro D6500K color temperature technology function makes sure that the video you
watch is set to the standard color temperature, so that what you see is as true to what the film
to video editors intended it to be.
Press the THAT. PRO (TheaterPro) button
Sleep Timer
The Sleep Timer can turn the TV off for you after you fall asleep. Program it to work for a total
time of up to 180 minutes. When you press the SLEEP button once, the rest of the time will be
displayed.
Sleep Timer
0 min.
Press the SLEEP button twice
15 min.
By every press of the SLEEP button, you select the time for
the timer to shut off
30 min.
45 min.
60 min.
90 min.
120 min.
180 min.
60 seconds before the automatic shut off, this message will
appear:
Good Night !
Push [SLEEP TIMER] button
to extend.
You then have 60 seconds to press the SLEEP button to delay the shut off.
Note:
• You can also select the timer by pressing the π† buttons.
45
Button Functions
Display
The display screen shows the current information as follows.
Press the DISPLAY button
Detailed mode
Clock Mode
Simple Mode
Off
• Detailed Mode - Shows the channel, channel name, signal, rating information, current time,
digital antenna level and scramble information, as well as the current time below.
(
(
o
))
(
(
S
))
Dolby Digital
TV PG
D L
S
V
NR
108-1
HD1080i CC
WEWEWEW
11:00PM - 11:30PM Football fun meeting
10:15PM
• Clock Mode - Shows the current time.
108-1
• Simple Mode - Shows the current channel and channel name or AV input.
WEWEWEW
• Off - Turns the display off.
Notes:
• You may also turn off the display at any step by pressing MENU.
• If the clock is not set, "Clock Not Set" will be displayed.
C.C. (Closed Caption)
Use the C.C. (Closed Caption) button to select the mode of closed caption.
Press the C.C. button
Closed Caption
On
Smart caption
Off
Notes:
• "Smart Caption" is for models AV-27F577 and AV-32F577 ONLY.
• Smart Caption will appear when you press the Muting button,
only on channels where the broadcast contains closed
captioning.
• When you select "On", it will be the mode selected in the Closed Caption Menu.
• See page 30 when you set the caption/text mode.
• You can also change the mode by pressing the π† buttons.
46
Button Functions
Aspect
This feature will help you adjust the picture you are watching to give you the best possible
picture quality.
Aspect Ratios
4:3 - Use this aspect mode when you
are watching a 4:3 broadcast.
16:9 - Use this aspect mode when you
are watching a 16:9 broadcast. This
is also referred to as "widescreen", for
example on a DVD disc. When you
select this mode, black bars will appear
on the top and bottom of the TV screen.
16:9 - If you select 16:9 aspect mode
while watching a 4:3 broadcast, this
will stretch the picture so as to fit into
the 16:9 format. When you select this
mode, black bars will appear on the top
and bottom of the TV screen.
ZOOM - If you are watching a 4:3 high
definition broadcast and you select
this aspect mode, it will zoom in on the
picture.
47
Button Functions
Aspect Ratios (Continued)
Press the ASPECT button
• By pressing the ASPECT button, you can change the size.
When you change the aspect ratios, it is different from their broadcast or recorded program.
Receiving 16:9 signal
Receiving 4:3 signal
Aspect
Aspect
4:3
4:3
16:9
Zoom
16:9
Notes:
• You can also choose the size by pressing the π† buttons.
• When you change the aspect ratio or signal, reset the picture position to center.
• You can also access the "Front Menu" screen by using the MENU button on the front of
the TV instead of the remote control. It has "Input", "Video Status" and "Aspect" menus.
Choose "Aspect" by pressing MENU
†
on the front panel and choose a mode by using the
CHANNEL +/- buttons ( OPERATE
√
® ).
48
Button Functions
Favorite
The Favorite button allows you to select your favorite channels easily. First, you must register
the channels that you like. See how to register below.
Press the FAVORITE button
Favorite
CBSXXXX
The favorite channel list will appear.
101
π†
To select the channel you want to watch
102
FOXXXX
103-1
PBSXXXX
Press the OK button
123-456 WEWEWEW
It will change to the channel you have selected.
107-2
HBOXXXX
ABCABC
NHKNHK
MBSMBS
8
1
4
Register the favorite channel
Press the channel number you want to register
The channel program will change.
Remove
Press the FAVORITE button for three seconds
The channel will be registered in the favorite channel list.
Notes:
• The maximum number of channels you can register is 24.
• If you have registered the maximum number of channels, and try to register more channels,
the oldest channel you registered will be deleted.
Delete the favorite channel
Press the FAVORITE button
Favorite
The favorite channel list will appear.
101
CBSXXXX
FOXXXX
102
π†
è
To select the channel you want to delete
To enter
103-1
PBSXXXX
Do you really remove Ch 101
from this list ?
123-456 WEWEWEW
107-2
HBOXXXX
ABCABC
NHKNHK
MBSMBS
The screen to the right will appear.
8
1
4
è
To "Yes"
Press the OK button
The channel was deleted.
Yes
No
Remove
Press the FAVORITE button when finished
49
Button Functions
ML/MTS
MTS technology allows several audio signals to be broadcast in analog at once, giving you a
choice in what you wish to hear with a TV program. In addition to mono or stereo sound, an
MTS broadcast may also include a second audio program (SAP).
Press the ML/MTS button
MTS
By every press of the ML/MTS button, you change the mode
Stereo
SAP
Mono
Notes:
• When you are receiving a digital broadcast, if there are other languages, you can change the
language by pressing the ML/MTS button.
• Keep the TV in stereo mode to get the best sound quality. The sound will work in stereo
mode even if a certain broadcast is in mono sound only.
• Choose the mono setting to reduce excessive noise on a certain channel or broadcast.
• Selecting SAP will allow you to hear an alternative soundtrack, if one is available.
• MTS unavailable if your television’s Input source is in input 1, 2 or 3 mode, as described on
page 43.
• You can also change the mode by pressing the π† buttons.
Menu
The Menu button allows you to access JVC’s onscreen menu system. Press MENU to activate
the onscreen menu system. When a menu is displayed, press the MENU button to exit the
menu system.
• See individual topics like “Sound Adjust” for specific information on using menus.
OK
This button confirms your selection when you are in one of the onscreen menus.
Back
This button allows you to go back in the menu to change a selection or correct a mistake.
50
Button Functions
DVD Buttons
You can also use this remote control to operate the basic functions of your DVD player. These
functions include: play, stop, still/pause, tray open/close, power on, power off, DVD Menu,
cursors and enter.
• The remote is preset to control JVC-brand DVD players only.
Sub Channel
The main channel sometimes has minor channels (Sub Channels). By using the SUB button,
you can select a sub channel easily.
For example, to move to sub channel 123-45:
Press 1, 2 and 3 in order
Press the SUB CH button
Press 4 and 5 in order
Press the TUNE button
Note:
• If there are more than 2 major channels, select the digital channel by using the π† buttons
and then press the OK button.
Guide
You can view the program information from the GUIDE.
Notes:
• The GUIDE will not show the correct time and date if you have not performed the set clock
function on your television. See page 41.
• When the program information is not being broadcasted, it will not show the correct
information.
Game
Sets automatically the proper conditions for playing video game (previously connected in the
front input).
Press the GAME button
Game mode
Input :
Video Status :
On
Video-3
Game
By pressing the GAME button, you can
change the Game Mode "On" or "Off".
51
Troubleshooting
PROBLEMS
CHECK
There is no power
• See if the power cord became unplugged.
• Check for a blown fuse or circuit breaker or a power outage.
There is no picture
or sound
• The antenna could be disconnected.
• The input mode could be set improperly. See page 43.
• The tuner (Auto Tuner Setup) could be set improperly. See page 33.
• The TV station may be having difficulties. Check to see if other stations are working.
Remote control is not • Check to see that the batteries are still working and properly installed.
operating properly or • Make sure the remote has a clear sight path to the TV.
at all
• You may be too far from the TV. You must be within 23 feet (7 meters).
You cannot select a
certain channel
• Make sure the channels have been programmed. See "Channel Summary", page 33.
• Check to see if the channel is locked. See "Channel Summary - Lock" page 34.
The power turns off
by itself
• Make sure the set did not become unplugged.
• Perhaps the On/Off Timer is set. See page 42.
• Check to see if the Sleep Timer was set. See page 45.
The clock is wrong
• The power was interrupted and the clock was not reset. See page 41.
The color quality
is poor
• Tint and Color may be improperly adjusted. See page 37.
• The Video Status mode may be turned to the wrong setting. See page 45.
There are lines
across the picture
• There could be interference from another electrical appliance, such as a computer,
another TV or VCR. Move any such appliances further away from the TV.
• There could be interference from a high-wattage appliance, like a hairdryer or vacuum,
operating nearby. Move the antenna away from the appliance or change to a coaxial
cable connection which is less prone to interference.
The picture is spotted
There are double
pictures (ghosts)
• A building or passing airplane can reflect the original signal and produce a second,
slightly delayed one. Adjust your antenna position.
Picture is snowy
(image noise)
• Your antenna may be damaged, disconnected or turned. Check the antenna
connection. If the antenna is damaged, replace it.
Screen is 40% black
• The Closed Caption Text mode is on. Turn it off in the Closed Caption Menu, page 30.
• Make sure the MTS settings are correct. See "MTS" on page 50.
Stereo or bilingual
programs can't be
heard
Static electricity
• It is normal to feel static electricity if you brush or touch the screen.
You hear occasional
crackling sounds
• It is normal for the TV to make crackling sounds when first turned on or off. Unless
the sound or picture become abnormal, this is fine.
Weak Signal
This OSD warning appears when the digital
channel that you have selected is too weak to
receive or no signal is being detected for that
channel.
No Program or Weak Signal
52
Specifications
AV-32WF47
AV-32MF47
AV-32F577
AV-27MF47
AV-27F577
MODEL
Reception
Format
NTSC, BTSC System (Multi-Channel Sound)
ATSC Terrestrial, Digital Cable
VHF 2 to 13, UHF 14 to 69 at ATSC,
Reception
Range
CATV 135 Sub, Mid, Super, Hyper and Ultra bands at Digital Cable
VHF 2 to 13, UHF 14 to 69 CATV 135 Sub, Mid, Super, Hyper
and Ultra bands (191 channel frequency synthesizer system) at Analog
• Reception of channel A-5 ("95" of the TV set's on-screen cable channel
numbers) is not recommended for your TV set.
AC 120V, 60Hz
Power Source
Power
Consumption
160W
140W
Screen Size
32 inch / 80 cm
measured diagonally
full square
27 inch / 68 cm
measured diagonally
full square
Audio Output
Speakers
5W + 5W
2 x 4 3/4 inch / 5 x 12 cm oval x 2
Antenna
Terminal
75 ohms (VHF/UHF) (F-type connector)
External Input
Jacks
Video: 1 Vp-p, 75 ohms
Audio: 500mVrms (-4dBvfs) high impediance
S-Video Input
Jack
Y: 1Vp-p positive, 75 ohms (negative sync provided)
C: 0.286 Vp-p (burst signal), 75 ohms
Component
Input Jacks
Y: 1Vp-p positive, 75 ohms (negative sync provided)
PB/PR: 0.7 Vp-p, 75 ohms
Audio Output
Jacks (FIX)
FIX: 500 mVrms (-4dBvfs) Low impedance (400 Hz when modulated 100%)
Digital Out (optical) x 1
Optical Output
Digital Audio
Dimensions (In)
WxHxD (cm)
34 5/8 x 27 5/8 x 22 1/4
87.7 x 69.9 x 56.5
29 7/8 x 23 3/8 x 19 3/4
75.8 x 59.3 x 50.0
Weight (lbs / kg)
Accessories
140.8 / 64
94.6 / 43
Remote control unit x 1, AA batteries x 2
Specifications subject to change without notice.
Notes:
• Reception of channel A-5 ("95" of the TV set's on-screen cable channel numbers) is not
recommended for your TV set.
• The open source software is embedded in this product. For more information, please go to:
53
54
55
JVC COMPANY OF AMERICA
Division of JVC Americas Corp.
1700 Valley Road
JVC CANADA, INC.
21 Finchdene Square
Scarborough, Ontario
Canada, M1X 1A7
Wayne, New Jersey, 07470
|