Color Television Users Guide
For Models:
AV-27530
AV-27WR25
Illustration of AV-27530 and RM-C203
Important Note:
In the spaces below, enter the model and serial number of your television (located at the rear
of the television cabinet). Staple your sales receipt or invoice to the inside cover of this guide.
Keep this user's guide in a convenient place for future reference. Keep the carton and original
packaging for future use.
Model Number:
LCT1531-001A-A
Serial Number:
0104KGI-II-IM
CAUTION ON REPLACABLE LITHIUM BATTERY
The battery used in this device may present a fire or chemical burn hazard if
mistreated. Do not recharge, disassemble, heat above 100ºC or incinerate.
Replace battery with CR2032 Panasonic (Matsushita Electric) or Maxell is
recommended.
Danger of explosion or risk of fire if the battery is incorrectly replaced.
• Dispose of used battery promptly.
• Keep away from children.
• Do not disassemble and do not dispose of in fire.
• As an “ENERGY STAR®” partner, JVC has determined
that this product or product model meets the “ENERGY
STAR®” guidelines for energy efficiency.
Important Safeguards
CAUTION:
Please read and retain for your safety.
Electrical energy can perform many useful functions. This TV set has been engineered and manufactured to
assure your personal safety. But improper use can result in potential electrical shock or fire hazards.
In order not to defeat the safeguards incorporated in this TV set, observe the following basic rules for its
installation, use and servicing. Also follow all warnings and instructions marked on your TV set.
INSTALLATION
1 Your TV set is equipped with a polarized AC line plug (one blade of the
plug is wider than the other). This safety feature allows the plug to fit into
the power outlet only one way. Should you be unable to insert the plug
fully into the outlet, try reversing the plug. Should it still fail to fit, contact
your electrician.
(POLARIZED-TYPE)
2 Operate the TV set only from a power source as indicated on the TV set or refer to the operating instructions
for this information. If you are not sure of the type of power supply to your home, consult your TV set dealer
or local power company. For battery operation, refer to the operating instructions.
3 Overloaded AC outlets and extension cords are dangerous, and so are frayed power cords and broken
plugs. They may result in a shock or fire hazard. Call your service technician for replacement.
4 Do not allow anything to rest on or roll over the power cord, and do not place the TV set where power cord is
subject to traffic or abuse. This may result in a shock or fire hazard.
5 Do not use this TV set near water – for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a
wet basement, or near swimming pool, etc.
6 If an outside antenna is connected to the TV set, be sure the antenna system is grounded so as to provide
some protection against voltage surges and built-up static charges. Section 810 of the National Electrical
Code provides information with respect to proper grounding of the mast and supporting structure, grounding
of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge
unit, connection requirements for the grounding electrode.
7 An outside antenna system
should not be located in the
vicinity of overhead power
lines or other electric light
or power circuits, or where it
can fall into such power lines
or circuits. When installing
an outside antenna system,
extreme care should be taken
to keep from touching such
power lines or circuits as
contact with them might be
fatal.
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRICAL
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ARTICLE 250, PART H)
NEC - NATIONAL ELECTRIC CODE
EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE
8 TV sets are provided with ventilation openings in the cabinet to allow heat generated during operation to be
released.
Therefore:
— Never block the bottom ventilation slots of a portable TV set by placing it on a bed, sofa, rug, etc.
— Never place a TV set in a “built-in” enclosure unless proper ventilation is provided.
— Never cover the openings with a cloth or other material.
— Never place the TV set near or over a radiator or heat register.
9 To avoid personal injury:
— Do not place a TV set on a sloping shelf unless properly secured.
— Use only a cart or stand recommended by the TV set manufacturer.
— Do not try to roll a cart with small casters across thresholds or deep pile carpets.
— Wall or shelf mounting should follow the manufacturer’s instructions, and should use a mounting kit
approved by the manufacturer.
Use
10 Caution children about dropping or pushing objects into the TV set through cabinet openings. Some
internal parts carry hazardous voltages and contact can result in a fire or electrical shock.
11 Unplug the TV set from the wall outlet before cleaning. Do not use liquid or an aerosol cleaner.
12 Never add accessories to a TV set that has not been designed for this purpose. Such additions may result
in a hazard.
PORTABLE CART WARNING (Symbol provided by RETAC)
13 For added protection of the TV set during a lightning storm or when the TV set is to be left unattended for
an extended period of time, unplug it from the wall outlet and disconnect the antenna. This will prevent
damage to product due to lightning storms or power line surges.
14 A TV set and cart combination should be moved with care. Quick stops, excessive force, and uneven
surfaces may cause the TV set and cart combination to overturn.
Service
15 Unplug this TV set from the wall outlet and refer servicing to qualified service personnel under the
following conditions:
A. When the power cord or plug is damaged or frayed.
B. If liquid has been spilled into the TV set.
C. If the TV set has been exposed to rain or water.
D. If the TV set does not operate normally by following the operating instructions. Adjust only those
controls that are covered in the operating instructions as improper adjustment of other controls may
result in damage and will often require extensive work by a qualified technician to restore the TV set to
normal operation.
E. If the TV set has been dropped or damaged in any way.
F. When the TV set exhibits a distinct change in performance — this indicates a need for service.
16 Do not attempt to service this TV set yourself as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
17 When replacement parts are required, have the service technician verify in writing that the replacement
parts he uses have the same safety characteristics as the original parts. Use of manufacturer’s specified
replacement parts can prevent fire, shock, or other hazards.
18 Upon completion of any service or repairs to this TV set, please ask the service technician to perform the
safety check described in the manufacturer’s service literature.
19 When a TV set reaches the end of its useful life, improper disposal could result in a picture tube
implosion. Ask a qualified service technician to dispose of the TV set.
20 Note to CATV system installer.
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC
that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be
connected to the grounding system of the building, as close to the point of cable entry as practical.
How to use the remote.
Before using, insert the lithium battery – CR2032 – correctly,
with the plus (+) side up into the battery compartment. To open
it, press the release tab and carefully pull the compartment out.
The remote control can operate most of your TV’s functions, as
well as basic functions of JVC VCRs.
2
R
C
* Point the remote towards the remote sensor on the target
component. The maximum operating distance is about 8
meters.
* To operate a JVC VCR, use any of the following buttons:
VCR POWER, TV/VCR INPUT, VCR CH+/-, PLAY, REWIND,
FAST-FORWARD, STOP, RECORD and PAUSE.
NOTE: If the remote does not work properly, remove the battery,
wait for a few seconds, replace the battery and try again.
Table of Contents
Quick Setup . . . . . . . . . . . 7
Button Functions . . . . . . . 32
Unpacking your TV . . . . . . . . . . . . 7
TV Models . . . . . . . . . . . . . . . . 8
TV Remote Controls . . . . . . . . . . . 9
Getting Started . . . . . . . . . . . . . 10
The Remote Control . . . . . . . . . . 10
Connecting Your Devices . . . . . . . 11
Auto Tuner Setup . . . . . . . . . . 15
Power . . . . . . . . . . . . . . . . . . 32
Number Buttons . . . . . . . . . . . . . 32
Channel +/– . . . . . . . . . . . . . . . 32
Volume +/– . . . . . . . . . . . . . . . 32
100+ Button . . . . . . . . . . . . . . . 32
Menu . . . . . . . . . . . . . . . . . . 32
Exit . . . . . . . . . . . . . . . . . . . 32
Return + . . . . . . . . . . . . . . . . . 33
Sleep . . . . . . . . . . . . . . . . . . 33
Muting . . . . . . . . . . . . . . . . . . 33
Display . . . . . . . . . . . . . . . . . 34
Video Status . . . . . . . . . . . . . . . 34
Game . . . . . . . . . . . . . . . . . . 35
Input . . . . . . . . . . . . . . . . . . . 35
C.C. . . . . . . . . . . . . . . . . . . . 35
VCR Buttons . . . . . . . . . . . . . . . 35
Onscreen Menus . . . . . . . . 16
Using the Guide . . . . . . . . . . . . . 16
Onscreen Menu System . . . . . . . . . 17
Initial Setup . . . . . . . . . . 18
Auto Tuner Setup . . . . . . . . . . . . 18
Channel Summary . . . . . . . . . . . . 18
V-Chip . . . . . . . . . . . . . . . . . . 19
Set Lock Code . . . . . . . . . . . . . 25
Language . . . . . . . . . . . . . . . . 26
Closed Caption . . . . . . . . . . . . . 26
Front Panel Lock . . . . . . . . . . . . 27
Auto Shut Off . . . . . . . . . . . . . . 27
Appendices . . . . . . . . . . 36
Troubleshooting . . . . . . . . . . . . . 36
Warranty . . . . . . . . . . . . . . . . . 37
Authorized Service Centers . . . . . . . 39
Specifications . . . . . . . . . . . . . . 40
Picture Adjust . . . . . . . . . 28
Picture Settings . . . . . . . . . . . . . 28
Adjust Picture Settings . . . . . . . . . 28
Noise Muting . . . . . . . . . . . . . . 28
Sound Adjust . . . . . . . . . 29
Sound Settings . . . . . . . . . . . . . 29
Adjust Sound Settings . . . . . . . . . 29
MTS (Multi-channel Sound) . . . . . . . 29
Clock Timers . . . . . . . . . . 30
Set Clock . . . . . . . . . . . . . . . . 30
On/Off Timer . . . . . . . . . . . . . . . 31
T
O
/
EAE
M
Quick Setup
TV Models
NOTE: Before you connect your television to another device, please refer to the proper
diagrams for your specific TV and remote. These will help assist you in understanding
how to connect your television to another device, as well as use the remote to set up
your television.
Rear Panel Diagram
INPUT 1
INPUT 2
COMPONENT
VIDEO
S-VIDEO
OVER
75W
(VHF/UHF)
VIDEO
VIDEO/Y
AUDIO OUT
AUDIO
L/MONO
L/MONO
PB
PR
L
R
R
R
MODELS: AV-27530 and AV-27WR25
Front Panel Diagram
INPUT - 3
POWER
VIDEO L/MONO - AUDIO - R
ON TIMER
MENU
+
+
– VOLUME
– CHANNEL
OPERATE
MODELS: AV-27530 and AV-27WR25
8
Quick Setup
TV Remote Controls
VIDEO
STATUS
VIDEO
STATUS
POWER
POWER
2
5
8
0
3
6
1
4
2
5
8
0
3
6
1
4
9
7
100
9
7
100
RETURN
RETURN
DISPLAY GAME SLEEP INPUT
DISPLAY GAME SLEEP INPUT
MUTING
C.C.
MUTING
C.C.
CH
CH
CH
CH
VOL
VOL
VOL
VOL
MENU
EXIT
MENU
EXIT
CHANNEL
POWER TV VCR
CHANNEL
POWER TV VCR
REW
PLAY
FF
REW
PLAY
FF
REC
STOP
PAUSE
REC
STOP
PAUSE
VCR CONTROL
RM-C203
VCR CONTROL
RM-C203G
RM-C203
RM-C203G
MODEL:
MODEL:
AV-27530
AV-27WR25
• For information on remote control buttons, see pages 32 - 35.
9
Quick Setup
Getting Started
Getting Started
These quick setup pages will provide you, in three easy steps, with the basic information you
need to begin using your new television right away.
If you have questions, or for more detailed information on any of these steps, please consult
other sections of this manual.
Step 1 – The Remote Control
Before you can operate your remote control, you first need to install the batteries (included).
With your thumb, push the latch on the back
of the remote control inward, and while
holding it there, pull the battery cover out
with your index finger. Insert the battery
(included) carefully noting the “+” and “–”
markings. Push the cover back into place.
R
C
Key Feature Buttons
MUTING
C.C.
The four key feature buttons at the center of the remote
can be used for basic operation of the television. The
top and bottom buttons will scan forward and back
through the available channels. To move rapidly through
the channels using JVC’s Hyperscan feature, press
and hold CH+ or CH–. The channels will zip by at a
rate of five channels per second. The right and left
buttons will turn the volume up or down. These buttons
are also marked with four arrows and are used with
JVC’s onscreen menu system. To use the onscreen
menus, press the MENU button.
CH
CH
VOL
VOL
MENU
EXIT
Note: Illustration of remote
control RM-C203
10
Quick Setup
Connections
Basic Operation
POWER
Turn the television on and off by pressing the POWER button at the top right
corner of the remote.
Step 2 – Connecting Your Devices
Please follow the flow chart below to determine which connection setup is right for you. Then,
refer to the appropriate diagrams to connect your television to other devices that you may have.
After you are finished connecting your devices, plug the power cord into the nearest power
outlet and turn on the TV.
A VCR is not necessary for operation of the television. If you follow these diagrams and the
television does not work properly, contact your local cable operator.
• To connect a DVD player, see Diagram #3. A DVD player is optional.
• If you have a satellite television system, please refer to the satellite TV manual.
Do you use a Cable TV Box?
Yes
No
Do you have a VCR?
Do you have a VCR?
Yes
No
Yes
No
Diagram #2 Diagram #1
Diagram #3 Diagram #1
11
Quick Setup
Connections
Diagram #1
Cable or Antenna
Output
Illustration of AV-27530
TV Rear Panel
Coaxial Cable
INPUT 1
INPUT 2
COMPONENT
VIDEO
S-VIDEO
OR
OVER
75W
(VHF/UHF)
VIDEO
VIDEO/Y
AUDIO OUT
AUDIO
L/MONO
L/MONO
PB
PR
L
R
R
OUT
IN
R
Cable Box
Note:
• If you do not have a cable box, connect the cable wire from the wall outlet into the back of the
TV.
Diagram #2
Cable or Antenna
Illustration of AV-27530
Output
TV Rear Panel
INPUT 1
INPUT 2
COMPONENT
VIDEO
S-V
OVER
75W
(VHF/UHF)
VIDEO
VIDEO/Y
AUDIO OUT
AUDIO
L/MONO
L/MONO
PB
PR
L
R
R
R
OR
Coaxial Cable
VCR
OUT
IN
OUT
OUT
IN
V
L
R
IN
Cable Box
Notes:
• If your VCR is a mono sound unit, it will have only one audio out jack. Connect it to the TV’s
LEFT AUDIO INPUT.
• Use the S-Video connection if possible for superior picture quality.
• Your VCR must be turned on to view premium cable channels.
12
Quick Setup
Connections
Illustration of AV-27530
Speaker
Speaker
Amplifier
13
Quick Setup
Connections
Connecting to a Camcorder
You may connect a camcorder, game console or other equipment to your television by using
the front input jacks. You can also connect these using the television’s rear input jacks, using
the same instructions.
INPUT - 3
POWER
VIDEO L/MONO - AUDIO - R
ON TIMER
MENU
+
+
– VOLUME
– CHANNEL
OPERATE
Camcorder
Illustration of AV-27530
1) Connect a yellow composite cable from the camcorder VIDEO OUT, into the VIDEO IN on
the front of the TV.
2) Connect a white composite cable from the camcorder LEFT AUDIO OUT, into the
LEFT AUDIO IN on the front of the TV.
3) Connect a red composite cable from the camcorder RIGHT AUDIO OUT, into the
RIGHT AUDIO IN on the front of the TV.
Note:
• If your camcorder is a mono sound model it will have only one AUDIO OUT. Connect it to the
LEFT AUDIO IN.
14
Quick Setup
Auto Tuner Setup
Step 3 – Auto Tuner Setup
JVC’s onscreen menu system lets you set your television up to meet your own personal viewing
preferences. The menu screens and their features are discussed in detail in this book. The menu
settings are optional, you can set as many or as few of them as you wish. But to begin watching
your television right away you will need to run the Auto Tuner Setup. This lets your television
learn the channels it is able to receive. To run the Auto Tuner Setup follow the steps below.
Press the Menu button on the remote control
π†
To AUTO TUNER SETUP
To operate
è
I N I T I A L S E T U P
A U T O T U N E R S E T U P
>
T U N E R M O D E
C A B L E
S T A R T
S E L E C T
B Y
E X I T
O P E R A T E B Y
E X I T B Y
è
To choose CABLE (if you are connected to a cable system) or AIR (if you use an
antenna)
π†
To move to START
è
To start Auto Tuner Setup
The Auto Tuner will now memorize all of the clear, active channels your television can receive.
This will take one or two minutes.
NOW
PROGRAMMING !
48
When the setup is finished, PROGRAMMING OVER ! is displayed. Your quick setup is now
complete. You can now begin watching your television, or you can continue on in this guide
for more information on programming your remote control, or using the JVC onscreen menu
system to customize your television viewing experience.
Cable Box and Satellite Users: After your auto tuner setup is complete, you may, (depending
on the type of hookup), have only 1 channel, usually 3 or 4 in the auto tuner memory. This is
normal.
The Quick Setup is complete
STOP
15
Onscreen Menus
Using the Guide
Certain symbols are used throughout this guide to help you learn about the features of your
new television. The ones you will see most frequently are:
π† Up and Down arrows mean press the CH+ or CH– buttons. Pressing the CH+ or CH–
buttons let you:
• Move vertically in a main menu screen
• Move through a submenu screen
• Move to the next letter, number, or other choice in a submenu
• Back up to correct an error
• Scan through TV channels (when not in a menu screen)
√® Left and right arrows mean press the VOLUME+ or VOLUME– buttons to move left or right
to:
• Select a highlighted menu item
• Select an item in a submenu
• Select numbers in certain menu options
• Turn the volume up or down (when not in a menu screen)
The “press button” icon means you should press the button named on your remote
control. (Button names appear in SMALL CAPITAL LETTERS.)
The “helping hand” icon points to the highlighted or selected item in a menu.
To bring up the onscreen menu, press the MENU button on the remote control. The item
that appears in yellow is the one currently selected. If you press the MENU button again, the
onscreen display will skip to the next menu screen. If you use the Menu button on the TV’s front
panel instead of the remote, an additional menu screen showing input will appear.
I N I T I A L
S E T U P
P R E V I O U S
A U T O T U N E R S E T U P
C H A N N E L S U M M A R Y
V – C H I P
S E T L O C K C O D E
N E X T P A G E
S E L E C T
B Y
E X I T
O P E R A T E B Y
E X I T B Y
Notes:
• Menus shown in this book are illustrations, not exact replications of the television’s onscreen
displays.
• If you do not press any buttons for a few seconds, the onscreen menu will automatically shut
off.
16
Onscreen Menus
The Onscreen Menu System
Your television comes with JVC’s onscreen menu system. The onscreen menus let you make
adjustments to your television’s operation simply and quickly. Examples of the Onscreen Menus
are shown below. Detailed explanations on using each menu follow later in this guide.
Press the MENU button
I N I T I A L
S E T U P
I N I T I A L
S E T U P
P R E V I O U S
P R E V I O U S
L A N G U A G E
C L O S E D C A P T I O N
F R O N T P A N E L L O C K
A U T O S H U T O F F
A U T O T U N E R S E T U P
C H A N N E L S U M M A R Y
V – C H I P
E N G . F R A N . E S P .
O F F
O F F
S E T L O C K C O D E
N E X T P A G E
N E X T P A G E
S E L E C T
B Y
S E L E C T
B Y
E X I T
O P E R A T E B Y
E X I T B Y
E X I T
O P E R A T E B Y
E X I T B Y
INITIAL SETUP 01
INITIAL SETUP 02
P I C T U R E
C L O C K /
T I M E R S
A D J U S T
P R E V I O U S
T I N T
S T A N D A R D
P R E V I O U S
S E T C L O C K
O N / O F F T I M E R
C O L O R
P I C T U R E
B R I G H T
D E T A I L
N E X T P A G E
N E X T P A G E
0
R E S E T B Y
S E L E C T
O P E R A T E B Y
B Y
S E L E C T
O P E R A T E B Y
B Y
E X I T
E X I T
E X I T B Y
E X I T B Y
CLOCK/TIMERS
PICTURE ADJUST 01
S O U N D
A D J U S T
P I C T U R E
A D J U S T
P R E V I O U S
B A S S
P R E V I O U S
N O I S E M U T I N G
S T A N D A R D
O N
T R E B L E
B A L A N C E
M T S
S T E R E O S A P M O N O
N E X T P A G E
N E X T P A G E
0
R E S E T B Y
S E L E C T
O P E R A T E B Y
B Y
S E L E C T
O P E R A T E B Y
B Y
E X I T
E X I T B Y
E X I T
E X I T B Y
SOUND ADJUST
PICTURE ADJUST 02
17
Initial Setup
Auto Tuner Setup
If you have already run the Auto Tuner as part of the quick setup earlier in this guide, please
skip ahead to “Channel Summary” to continue setting up your television.
Press the MENU button
I N I T I A L S E T U P
>
A U T O T U N E R S E T U P
π†
è
è
†
To AUTO TUNER SETUP
To operate
T U N E R M O D E
C A B L E
To choose CABLE or AIR
To move to START
S T A R T
S E L E C T
B Y
E X I T
O P E R A T E B Y
E X I T B Y
è
To start Auto Tuner Setup
Programming will take approximately 1 to 2 minutes. The auto tuner is finished when the
message PROGRAMMING OVER! appears onscreen.
Channel Summary
Channel summary allows you to customize the line-up of channels received by your TV. You can
add or delete channels from the line-up or prevent any unauthorized viewers from watching any
or all 181 channels.
Press the MENU button
π†
To CHANNEL SUMMARY
To operate
è
The Channel summary screen will now be displayed with
the channels set to scan marked with an “√”. You can
delete channels from the scan by removing the “√”. If any
channels were missed during auto tuner setup and you
wish to add them, you may by placing an “√” next to the
channel number.
I N I T I A L S E T U P
C H A N N E L S U M M A R Y
>
I
I
I
I
I
I
C
H
N
O
S
C
A
N
C
H
N
O
.
S
C
A
N
1
2
3
4
5
6
7
8
9
1 0
π†
To the SCAN column
S E L E C T
O P E R A T E B Y
B Y
E X I T
E X I T B Y
è
To include or delete from scan
Press the EXIT button when finished
You can block access to a channel by activating the channel lock.
Press the MENU button
π†
è
π†
To CHANNEL SUMMARY
To operate
To the Lock Column (
)
Press the ZERO button to lock or unlock that channel
Press the EXIT button when finished
18
Initial Setup
Channel Guard Message
When a viewer attempts to watch a guarded channel, the following message appears:
To watch a channel that you have locked, enter the Lock
THIS CHANNEL IS LOCKED BY
Code using the 10 key pad.
CHANNEL GUARD.
PLEASE ENTER LOCK CODE BY
10 KEY PAD TO UNLOCK IT.
NO. - - - -
If the wrong code is entered, the message
“INVALID LOCK CODE!” will flash on the screen.
The channel cannot be accessed until the correct code
is entered.
Notes:
• Once a channel has been unlocked, it will remain unlocked until the television is turned off.
• See also “Set Lock Code”, page 25.
V-Chip
Your TV is equipped with V-Chip technology which enables you to block channels or content that
you feel to be inappropriate for children, based on US and Canada rating guidelines. V-Chip
has no effect on video signals from a DVD discs, VCR tapes or Camcorder connection.
Note: Some programs, and movies are broadcast without a ratings signal. Even if you set
up V-CHIP ratings limits, these programs will not be blocked. See page 20 for information on
how to block unrated programs.
Note (for Canadian viewers): The V-Chip function is based on specifications designed for
the United States and therefore may not work properly in Canada.
You can customize the V-Chip settings of your television to match your personal tastes. The
V-Chip menu below is the starting point for your V-Chip settings
You can use US V-Chip settings (for programming broadcast from the United States), Canadian
V-Chip settings (for programming broadcast from Canada), and movie ratings. You may use any
or all of the settings (US V-Chip, Canada V-Chip, Movie ratings). Descriptions for setting each
of the three V-Chip formats appear in the next six pages along with descriptions of the rating
categories.
To access the rating categories:
I N I T I A L S E T U P
>
Press the MENU button
V – C H I P
V – C H I P
O F F
S E T U S T V R A T I N G S
S E T M O V I E R A T I N G S
S E T C A N A D I A N R A T I N G S E N G
S E T C A N A D I A N R A T I N G S F R E
π†
è
To V-CHIP
To operate (Lock icon
will appear)
U N R A T E D
V I E W
Press ZERO to access the V-Chip menu
F I N I S H
è
To turn V-Chip ON or OFF (V-Chip must be
turned ON for rating settings to operate)
S E L E C T
O P E R A T E B Y
B Y
E X I T
E X I T B Y
π†
To move to SET US TV RATINGS,
SET MOVIE RATINGS, or SET CANADIAN RATINGS (see following pages for
descriptions of each item)
19
Initial Setup
Unrated Programs
Unrated programming refers to any programming which does not contain a rating signal.
Programming on television stations which do not broadcast rating signals will be placed in the
“Unrated Programming” category.
Examples of Unrated programs:
• Emergency Bulletins
• News
• Public Service Announcements
• Sports
• Locally Originated Programming
• Political Programs
• Religious Programs
• Weather
• Some Commercials
Note:
• TV programs or movies that do not have rating signals will be blocked if the unrated category
is set to BLOCK.
Directions to Block Unrated Programs
You can block programs that are not rated.
Press the MENU button
I N I T I A L S E T U P
>
V – C H I P
V – C H I P
S E T U S T V R A T I N G S
S E T M O V I E R A T I N G S
S E T C A N A D I A N R A T I N G S E N G
S E T C A N A D I A N R A T I N G S F R E
U N R A T E D
O F F
π†
To V-CHIP
è
To operate (The lock icon
appears)
Press ZERO to access V-Chip setup options
V I E W
π†
To UNRATED
F I N I S H
S E L E C T
O P E R A T E B Y
B Y
è
To VIEW or BLOCK
E X I T
E X I T B Y
Press EXIT when done
20
Initial Setup
US V-Chip Ratings
U.S. PARENTAL RATING SYSTEMS
Programs with the following ratings are appropriate for children.
❒ TV Y is Appropriate for All Children
Programs are created for very young viewers and should be suitable for all ages, including
children ages 2 - 6.
❒ TV Y7 is for Older Children
Most parents would find such programs suitable for children 7 and above. These programs
may contain some mild fantasy violence or comedic violence, which children should be able
to discern from reality.
Programs with the following ratings are designed for the entire audience.
❒ TV G stands for General Audience
Most parents would find these programs suitable for all age groups. They contain little or no
violence, no strong language, and little or no sexual dialog or situations.
❒ TV PG Parental Guidance Suggested
May contain some, but not much, strong language, limited violence, and some suggestive
sexual dialog or situations. It is recommended that parents watch these programs first, or
with their children.
❒ TV 14 Parents Strongly Cautioned
Programs contain some material that may be unsuitable for children under the age of 14
including possible intense violence, sexual situations, strong coarse language, or intensely
suggestive dialog. Parents are cautioned against unattended viewing by children under 14.
❒ TV MA Mature Audiences Only
These programs are specifically for adults and may be unsuitable for anyone under 17 years
of age. TV MA programs may have extensive V, S, L, or D.
Viewing Guidelines
In addition to the ratings categories explained above, information on specific kinds of content
are also supplied with the V-Chip rating. These types of content may also be blocked. The
content types are:
• V/FV is for VIOLENCE/FANTASY VIOLENCE
• S stands for SEXUAL CONTENT
• L stands for strong LANGUAGE
• D stands for suggestive DIALOG
21
Initial Setup
Setting US V-Chip Ratings
Press the MENU button
I N I T I A L S E T U P
V – C H I P
>
V – C H I P
S E T U S T V R A T I N G S
S E T M O V I E R A T I N G S
S E T C A N A D I A N R A T I N G S E N G
S E T C A N A D I A N R A T I N G S F R E
U N R A T E D
O F F
π†
è
To V-CHIP
To operate (lock icon
appears)
Press ZERO to access the V-Chip menu
V I E W
è
π†
è
To turn V-Chip ON or OFF
To move to SET US TV RATINGS
To operate
F I N I S H
S E L E C T
O P E R A T E B Y
B Y
E X I T
E X I T B Y
Directions to set US V-Chip Ratings
Line up the cursor in the column (TV PG, TV G, etc.) with the content row (V/FV, S, etc.) and
press the or to move the cursor to the correct location. Press or to turn the locking
feature on or off. An item is locked if the icon appears instead of a “—”.
π
†
√
®
For example. To block viewing of all TV 14 shows, move the cursor to the top row of that
column and add a lock icon. Once you’ve put a lock on the top row, everything in that column is
automatically locked.
π†
è
π†
è
To the TV 14 Column
To turn on the lock
To FINISH
To save settings and exit
Press the EXIT button when finished
Note:
• If you want to change the setup, move the cursor to the top column and change the lock icon
to “—” by pressing or again. You may then select individual categories to block.
√
®
22
Initial Setup
Movies Ratings
❒ NR – Not Rated
This is a film which has no rating. In many cases these films were imported from countries
which do not use the MPAA ratings system. Other NR films may be from amateur producers
who didn’t intend to have their film widely released.
NR (Not Rated) Programming may contain all types of programming including
children’s programming, foreign programs, or adult material.
❒ G – General Audience
In the opinion of the review board, these films contain nothing in the way of sexual content,
violence, or language that would be unsuitable for audiences of any age.
❒ PG – Parental Guidance
Parental Guidance means the movie may contain some contents such as mild violence,
some brief nudity, and strong language. The contents are not deemed intense.
❒ PG-13 – Parents Strongly Cautioned
Parents with children under 13 are cautioned that the content of movies with this rating may
include more explicit sexual, language, and violence content than movies rated PG.
❒ R – Restricted
These films contain material that is explicit in nature and is not recommended for
unsupervised children under the age of 17.
❒ NC-17 – No One Under 17
These movies contain content which most parents would feel is too adult for their children
to view. Content can consist of strong language, nudity, violence, and suggestive or explicit
subject matter.
❒ X – No One under 18
Inappropriate material for anyone under 18.
Directions to set Movie (MPAA) Ratings
Press the MENU button
π†
è
To V-CHIP
To operate (Lock icon
appears)
Press ZERO to access V-Chip setup options
π†
è
To SET MOVIE RATINGS
To enter movies menu
For example:
To block viewing of X and NC-17 rated from shows:
I N I T I A L S E T U P
>
V – C H I P
>
S E T M O V I E R A T I N G S
π†
è
π†
To the X Column
N
P
X
R
PG
G
NR
C-17
G-13
To turn on the lock
To the NC-17 Column
To turn on the lock
F I N I S H
è
π†
è
S E L E C T
O P E R A T E B Y
B Y
E X I T
E X I T B Y
To FINISH
To save settings and exit
Press the EXIT button when finished
23
Initial Setup
Canadian V-Chip Ratings
❒ E – Exempt
Exempt programming includes: news, sports, documentaries and other information
programming, talk shows, music videos, and variety programming.
❒ C – Programming Intended for Children
Violence Guidelines: There will be no realistic scenes of violence. Depictions of aggressive
behavior will be infrequent and limited to portrayals that are clearly imaginary, comedic or
unrealistic in nature.
❒ C8+ – Programming Intended for Children 8 and Over
Violence Guidelines: Any realistic depictions of violence will be infrequent, discreet, of low
intensity and will show the consequences of the acts. There will be no offensive language,
nudity or sexual content.
❒ G – General Audience
Programming will contain little violence and will be sensitive to themes which could affect
younger children.
❒ PG – Parental Guidance
Programming intended for a general audience, but which may not be suitable for younger
children. Parents may consider some content not appropriate for children aged 8-13.
❒ 14+ – 14 Years and Older
Parents are strongly cautioned to exercise discretion in permitting viewing by pre-teens and
early teens. Programming may contain mature themes and scenes of intense violence.
❒ 18+ – Adult
Material intended for mature audiences only.
Directions to set Canadian V-Chip Ratings
Press the MENU button
π†
è
To V-CHIP
To operate (lock icon
appears)
Press ZERO to access V-Chip setup options
π†
è
To SET CANADIAN RATINGS ENG (for English)
To enter ratings menu
For example:
To block viewing of programming rated 14+ and 18+:
I N I T I A L S E T U P
>
V – C H I P
>
S E T M O V I E R A T I N G S
π†
è
To the 18+ Column
To turn on the lock
P
C
G
C
14+
18+
G
8
π†
è
π†
To the 14+ Column
To turn on the lock
To FINISH
F I N I S H
S E L E C T
O P E R A T E B Y
B Y
è
To save settings and exit
Press the EXIT button when finished
E X I T
E X I T B Y
Note:
• For instructions on “SET CANADIAN RATINGS FRE (in French)”, please see page 24 in the
French side of this user’s guide.
24
Initial Setup
Set Lock Code
Channel guard and V-Chip settings are protected by a four-digit lock code. Your TV comes
pre-set with a lock code of “0000”. You may change the code to any four-digit number you wish.
To change the lock code, follow the steps below.
Press the MENU button
I N I T I A L S E T U P
>
S E T L O C K C O D E
L O C K C O D E
F I N I S H
π†
To SET LOCK CODE
To operate (lock icon
è
appears)
0 0 0 0
Press ZERO to access the lock code
The first digit will be highlighted
S E L E C T
B Y
E X I T
E X I T B Y
O P E R A T E B Y
è
π†
To select the number
To move to the next digit
Continue to follow these directions for all four numbers
π†
To FINISH
è
To save settings and exit
(your lock code is now set)
Press the EXIT button when finished
When a viewer attempts to watch a blocked channel, this message appears:
THIS PROGRAMMING EXCEEDS
YOUR RATING LIMITS.
PLEASE ENTER LOCK CODE BY
10 KEY PAD TO UNLOCK IT.
NO. - - - -
The channel will remain blocked until the correct lock code is entered (see above for information
on setting your lock code).
Notes:
• After a power interruption you must reset the lock code.
• Write your lock code number down and keep it hidden from potential viewers.
• If you forget the lock code, a new code may be set using the steps listed above.
25
Initial Setup
Language
You can choose to view your onscreen menus in three languages: English, French (Français)
or Spanish (Español).
Press the MENU button
I N I T I A L
S E T U P
π†
To LANGUAGE
P R E V I O U S
L A N G U A G E
C L O S E D C A P T I O N
F R O N T P A N E L L O C K
A U T O S H U T O F F
E N G . F R A N . E S P .
è
To choose a language: ENG. (English), FRAN.
(French) or ESP. (Spanish)
O F F
O F F
Press the EXIT button when finished
N E X T P A G E
S E L E C T
B Y
E X I T
O P E R A T E B Y
E X I T B Y
Closed Caption
Many broadcasts now include an onscreen display of dialog called closed captions. Some
broadcasts may also include displays of additional information in text form. Your television can
access and display this information using the closed caption feature. To activate the closed
caption feature, follow the steps below.
Press the MENU button
π†
è
π†
è
To CLOSED CAPTION
To operate
To select CAPTION or TEXT
To select a caption (CC1 to CC4) or text
channel (T1 to T4)
I N I T I A L S E T U P
C L O S E D C A P T I O N
>
C A P T I O N
T E X T
C C 1
T 1
π†
è
To accept that selection and move to FINISH
To save settings and exit
F I N I S H
S E L E C T
B Y
Press the EXIT button when finished
E X I T
O P E R A T E B Y
E X I T B Y
Notes:
• Closed caption subtitles are usually found on closed caption channel CC1. Some programs
may include additional text information which is usually found on text channel T1. The other
channels are available for future use.
• Closed captioning may not work correctly if the signal being received is weak or if you are
playing a video tape.
• Most broadcasts containing closed captioning will display a notice at the start of the program.
• To select the mode, press the C.C. button. See page 35.
26
Initial Setup
Front Panel Lock
This allows you to lock the keys on the front of the TV, so that a child may not accidentally
change your viewing preferences.
Press the MENU button
π†
è
To FRONT PANEL LOCK
To turn ON or OFF
Press the EXIT button when finished
You can turn off this feature in the following ways:
• Unplug the power cord, and plug it back in. Do this if your batteries die, or you lose your
remote control.
• Use the remote control.
• Press the MENU button on the front of the TV for more than 3 seconds. In this case, the OSD
for FRONT PANEL LOCK will appear.
Note:
• To turn ON/OFF the TV, press the power button for more than 3 seconds. This feature will
remain ON.
Auto Shut Off
This function automatically shuts off your TV when there is no signal from the channel the TV is
on.
Press the MENU button
π†
è
To AUTO SHUT OFF
To turn ON or OFF
Press the EXIT button when finished
• If the channel that you have on does not receive a signal for more than one minute, the
blinking text “NOT RECEIVING A SIGNAL” appears on the screen, and starts the countdown.
If no signal is being received within 9 minutes, the TV shuts itself off.
27
Picture Adjust
Picture Settings
These settings allow you to change and adjust the way the picture appears on your television.
TINT
Tint allows you to adjust the levels of red and green in your TV picture.
COLOR
The color function lets you make all the colors in the TV picture appear either more vivid or
subtle.
PICTURE
Picture allows you to adjust the levels of black and white on the TV screen, giving you a darker
or brighter picture overall.
BRIGHT
You can adjust the overall brightness of the TV picture with the Bright control.
DETAIL
The Detail feature adjusts the level of fine detail displayed in the picture.
Adjust the Picture Settings
Press the MENU button
P I C T U R E
A D J U S T
π†
To TINT, COLOR, PICTURE, BRIGHT or
DETAIL
P R E V I O U S
T I N T
C O L O R
S T A N D A R D
P I C T U R E
B R I G H T
D E T A I L
√ ®
√ ®
π†
To enter
To adjust the setting
To move to the next setting
N E X T P A G E
0
R E S E T B Y
S E L E C T
B Y
Press the EXIT button when finished
E X I T
O P E R A T E B Y
E X I T B Y
Note:
• If you press the 0 button, you can reset the setting to the factory default setting.
Noise Muting
This feature inserts a blank blue screen over channels which are not broadcasting or are too
weak to be received clearly.
Press the MENU button
P I C T U R E
A D J U S T
P R E V I O U S
N O I S E M U T I N G
S T A N D A R D
O N
π†
To NOISE MUTING
è
To turn noise muting ON or OFF
Press the EXIT button when finished
N E X T P A G E
S E L E C T
B Y
E X I T
O P E R A T E B Y
E X I T B Y
Note:
• Noise muting will not work during auto tuner setup or when you operate channel summary.
28
Sound Adjust
Sound Settings
These settings allow you to change and adjust the sound on your television.
BASS – You can increase or decrease the level of low-frequency sound in the TV’s audio with
the bass adjustment.
TREBLE – Use treble to adjust the level of high-frequency sound in your TV’s audio.
BALANCE – Adjust the level of sound between the TV’s left and right speakers with the
balance setting.
Adjust the Sound Settings
Press the MENU button
S O U N D
A D J U S T
P R E V I O U S
B A S S
T R E B L E
B A L A N C E
M T S
π†
√ ®
π†
To BASS, TREBLE or BALANCE
To adjust the setting
To move to the next setting
S T E R E O S A P M O N O
Press the EXIT button when finished
N E X T P A G E
0
R E S E T B Y
S E L E C T
B Y
E X I T
O P E R A T E B Y
E X I T B Y
Note:
• If you press the 0 button, you can reset the setting to the factory default setting.
MTS (Multi-Channel Television Sound)
MTS technology allows several audio signals to be broadcast at once, giving you a choice
in what you wish to hear with a TV program. In addition to mono or stereo sound, an
MTS broadcast may also include a second audio program (SAP).
Press the MENU button
π†
To MTS
è
Select the mode
(The ON AIR arrow tells you if a broadcast is in stereo and/or contains an SAP).
Press the EXIT button when finished
Notes:
• Keep the TV in stereo mode to get the best sound quality. The sound will work in stereo
mode even if a certain broadcast is in mono sound only.
• Choose the mono setting to reduce excessive noise on a certain channel or broadcast.
• Selecting SAP will allow you to hear an alternative soundtrack, if one is available.
• MTS is unavailable if your television’s input source is in input 1, 2, or 3 mode, as described on
page 35.
29
Clock/Timers
Set Clock
Before you use any of your TV’s timer functions, you must first set the clock. You may precisely
set your clock using the XDS time signal broadcast by most public broadcasting stations. If you
do not have this in your area, you will have to set the clock manually. See manual clock set
below. To set the clock using the XDS signal:
Press the MENU button
π†
To SET CLOCK
To operate
è
When you set the clock automatically, choose AUTO by pressing the
√
or
®
arrows.
π†
è
π†
è
†
To TIME ZONE
C L O C K / T I M E R S
S E T C L O C K
>
To select your time zone
To D.S.T. (daylight savings time)
To turn D.S.T. ON or OFF
To FINISH
M O D E
A U T O
T I M E Z O N E
D . S . T .
P A C I F I C
O F F
F I N I S H
S E L E C T
B Y
E X I T
O P E R A T E B Y
E X I T B Y
è
To save settings
Press the EXIT button when finished
When you set the clock manually, choose MANUAL by pressing the
√
or
®
arrows.
π†
è
π†
è
†
To move to the hour
To set the hour
C L O C K T I M E R S
S E T C L O C K
>
M O D E
M A N U A L
To move to minutes
To set the minutes
To START CLOCK
To operate
T I M E
– – : – – – –
S T A R T C L O C K
B Y
S E L E C T
E X I T
E X I T B Y
O P E R A T E B Y
è
THANK YOU !!
30
Clock/Timers
On/Off Timer
The on/off timer lets you program your television to turn itself on or off. You can use it as an
alarm to wake up, to help you remember important programs, or as a decoy when you’re not
home.
Press the MENU button
C L O C K / T I M E R S
>
O N / O F F T I M E R
π†
è
è
To ON/OFF TIMER
O N T I M E
7 : 0 0 P M
1 0 : 0 0 P M
0 2
C U R R E N T
E V E R Y D A Y
N O
O F F T I M E
C H A N N E L
O N V O L U M E
M O D E
To operate (begins with ON TIME)
To set the hour (AM/PM) you want the TV to turn
on
O N / O F F T I M E R
F I N I S H
S E L E C T
B Y
†
è
†
To move to minutes
To set the minutes
E X I T
E X I T B Y
O P E R A T E B Y
To accept ON TIME and move to OFF TIME (the time the TV will turn off). Set the
OFF TIME the same way as ON TIME
†
è
†
To accept OFF TIME and move to CHANNEL
To select channel
To ON VOLUME
è
†
To set the volume level
To move to MODE
è
Choose ONCE or EVERYDAY
†
è
†
To ON/OFF TIMER
Choose YES to accept the timer setting, choose NO if you don’t wish to accept
To FINISH
è
To save settings
Press the EXIT button when finished
Notes:
• The on/off time cannot be set to locked or guarded channels.
• In order for the on/off timer to work, the clock must be set.
• After a power interruption, the timer settings must be reset.
31
Button Functions
Power
Turns the TV on or off.
Press the POWER button
Number Buttons - 10Key Pad
Use the number buttons on the remote control to move directly to a specific channel. For
example, to move to channel 7:
0 (Zero)
7 (Seven)
Channel +/–
Use these buttons to move up or down all the available channels your TV is able to recieve.
Volume +/–
Use these buttons to raise or lower the TV’s volume level.
100+ Button
Use the 100+ button to directly access channels above channel 99. For example, to move to
channel 124, press 100+, 2 (Two), 4 (Four).
Menu
The MENU button allows you to access JVC’s onscreen menu system. Press MENU to activate
the onscreen menu system.
• See individual topics like “Sound Adjust” for specific information on using menus.
Exit
Use this button to enter or exit the TV’s onscreen menus.
32
Button Functions
Return +
The RETURN+ button has two functions:
Return - Returns to the channel viewed just before the channel currently onscreen.
Return+ - Lets you program a specific channel to return to while scanning through the channels
using the CH+ and CH– buttons.
RETURN+ and hold for three seconds
RETURN CHANNEL
PROGRAMMED!
The channel currently active has been programmed as your return+ channel. Now scan through
the channels using the CHANNEL+/– buttons.
RETURN+
You will return to your programmed channel.
• To cancel your Return+ channel, press and hold the RETURN+ button for three seconds. The
message “RETURN CHANNEL CANCELLED!” will appear.
• Return+ works only with the CH+/– buttons. Pressing any number key will cancel Return+.
Sleep
The Sleep Timer can turn the TV off for you after you fall asleep. Program it to work in intervals
of 15 minutes, for a total time of up to 180 minutes.
Press the SLEEP button
0 15 30 45 60 75 90 105 120 135 150 165 180
Sleep Timer Message
20 seconds before the automatic shutoff, this message will appear:
GOOD NIGHT!!
PUSH SLEEP TIMER BUTTON
TO EXTEND
You then have 20 seconds to press the SLEEP button to delay the shut off for another
15 minutes.
Muting
The MUTING button instantly turns the volume down completely when you press it. Press
MUTING and the volume level will instantly go to zero. To restore the volume to its previous level,
press MUTING again.
33
Button Functions
Display
The display screen shows the current status of timers and inputs.
Press the DISPLAY button
The screen to the right shows the following information:
07 KLVX PBS
• The current channel or AV input (Channel 05)
• The current time (12:20 pm)
• Sleep timer status/minutes remaining (The Sleep Timer
is off)
• On/off timer status (Set to turn on everyday at 7:00 PM,
off at 10:00 PM)
JAZZ FESTIVAL
NOW
SLEEP TIMER
ON/OFF TIMER
ON TIME
12 : 20 PM
OFF
EVERYDAY
7 : 00 PM
10 : 00 PM
OFF TIME
• Each Press of the DISPLAY button changes the display
mode:
Display
Time
Channel
Off
Display - Full screen shown above
Time - Shows the current time only
Channel - Shows the current channel
Off - Turns display off
Notes:
• You may also turn off the display at any step by pressing MENU.
• If the clock, sleep timer or on/off timer are not set, the display screen will show:
“CLOCK NOT SET”, “SLEEP TIMER OFF”, and “ON/OFF TIMER OFF” respectively.
Video Status
The VIDEO STATUS button gives you a choice of four TV picture display settings, including a
display of your own preferences.
STANDARD - Resets the picture display to the factory settings.
DYNAMIC - Heightens contrast.
SPORTS - When you watch a sports program.
GAME - Used for when you are playing video games connected to your TV.
Press the VIDEO STATUS button
By every press of the video status button, you change the mode.
STANDARD
DYNAMIC
SPORTS
GAME
34
Button Functions
Game
Sets automatically the proper conditions for playing video game (previously connected in the
front input).
Press the GAME button
GAME MODE
INPUT
VIDEO STATUS
ON
VIDEO-3
GAME
Input
Selects the signal input source for the television: TV (for Antenna or Cable) or Video-1, 2, or
V2-Component or Video-3 for video devices like VCR’s, DVD players, or camcorders.
Press the INPUT button
TV
VIDEO-1
VIDEO-2
V2-COMPONENT
VIDEO-3
Note:
• You can also access the input menu screen by using the MENU button on the front of the TV
instead of the remote control. It appears between INITIAL SETUP and PICTURE ADJUST
screen. Choose the INPUT by pressing MENU
†
on the front panel and select TV or VIDEO
INPUT by using the CHANNEL +/- buttons (
√
OPERATE ).
®
C.C. (Closed Caption)
Use the C.C. (Closed Caption) button to select the mode of closed caption.
Press the C.C. button
OFF
CAPTION
TEXT
• See page 26 when you set the caption/text mode.
VCR Buttons
Note: The remote controls can only be used with JVC-brand VCRs
You can use this remote control to operate the basic functions of your VCR. These functions
include: play, record, rewind, fast-forward, stop, pause, channel scan, TV/VCR, power on, and
power off.
Press the TV/VCR button to operate the VCR.
35
Troubleshooting
PROBLEMS
CHECK
There is no power
• See if the power cord became unplugged.
• Check for a blown fuse or circuit breaker or a power outage.
There is no picture
or sound
• The antenna could be disconnected.
• The input mode could be set improperly. See page 35.
• The tuner (Auto Tuner Setup) could be set improperly. See page 18.
• The TV station may be having difficulties. Check to see if other stations are working.
Remote control is not • Check to see that the batteries are still working and properly installed.
operating properly or • Make sure the remote has a clear sight path to the TV.
at all
• You may be too far from the TV. You must be within 23 feet (7 meters).
You cannot select a
certain channel
• Make sure the channels have been programmed. See "Channel Summary", page 18.
• Check to see if the channel is locked. See "Channel Summary - Lock" page 19.
The power turns off
by itself
• Make sure the set did not become unplugged.
• Perhaps the On/Off Timer is set. See page 31.
• Check to see if the Sleep Timer was set. See page 33.
The clock is wrong
• The power was interrupted and the clock was not reset. See page 30.
• There is a problem with the TV. Unplug the set and call for service.
The On Timer is
blinking
The color quality
is poor
• Tint and Color may be improperly adjusted. See page 28.
• The Video Status mode may be turned to the wrong setting. See page 34.
There are lines
across the picture
• There could be interference from another electrical appliance, such as a computer,
another TV or VCR. Move any such appliances further away from the TV.
• There could be interference from a high-wattage appliance, like a hairdryer or vacuum,
operating nearby. Move the antenna away from the appliance or change to a coaxial
cable connection which is less prone to interference.
The picture is spotted
There are double
pictures (ghosts)
• A building or passing airplane can reflect the original signal and produce a second,
slightly delayed one. Adjust your antenna position.
Picture is snowy
(image noise)
• Your antenna may be damaged, disconnected or turned. Check the antenna
connection. If the antenna is damaged, replace it.
Screen is 80% black • The Closed Caption Text mode is on. Turn it off in the Closed Caption Menu, page 26.
Stereo or bilingual
programs can't be
heard
• Make sure the MTS settings are correct. See "MTS" on page 29.
Static electricity
• It is normal to feel static electricity if you brush or touch the screen.
You hear occasional • It is normal for the TV to make crackling sounds when first turned on or off. Unless
crackling sounds the sound or picture become abnormal, this is fine.
36
Warranty
For Canadian model televisions, see the separate sheet for Canadian
Warranty information.
JVC COMPANY OF AMERICA warrants this product and all parts thereof, except as set forth
below ONLY TO THE ORIGINAL PURCHASER AT RETAIL to be FREE FROM DEFECTIVE
MATERIALS AND WORKMANSHIP from the date of original retail purchase for the period
shown below (the “Warranty Period”) (PICTURE TUBE is covered for Two (2) years.)
LABOR 1 YEAR
PARTS 1 YEAR
THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE
DISTRICT OF COLUMBIA AND COMMONWEALTH OF PUERTO RICO.
WHAT WE WILL DO:
If this product is found to be defective within the warranty period, JVC will repair or
replace defective parts at no charge to the original owner. Such repair and replacement
services shall be rendered by JVC during regular business hours at JVC authorized
service centers. Parts used for replacement are warranted only for the remainder of this
Warranty Period. All products and parts thereof may be brought to a JVC authorized
service center on a carry-in basis. Televisions with a screen size of 25 inches and larger
may be covered on an in-home basis where such service is available.
WHAT YOU MUST DO FOR WARRANTY SERVICE:
To determine if in-home service is available in your area, either contact the selling dealer
(retailer) or call 1-800-537-5722 to locate the nearest JVC authorized service center. Service
available, will require clear access to the Television by the service representatives. If in-home
service is not available, carry in service will be provided.
If service is not locally available, box the product carefully, preferably in its original
carton, and ship, insured, with a copy of your bill of sale plus a letter of explanation of
the problem to the nearest JVC Factory Service Center, the name and location which will
be given to you by the toll free number.
If you have any questions concerning your JVC Product, please contact our Customer
Relations Department.
WHAT IS NOT COVERED:
This limited warranty provided by JVC does not cover:
1) Products which have been subject to abuse, accident, alteration, modification,
tampering, negligence, misuse, faulty installation, lack of reasonable care, or if
repaired or serviced by anyone other than a service facility authorized by JVC to
render such service, or if affixed to any attachment not provided with the products,
or if the model or serial number has been altered, tampered with, defaced or
removed;
2) Initial installation, installation and removal from “built-in” entertainment centers and
other mounting systems;
3) Operational adjustments covered in the Owner’s Manual, normal maintenance, video
and audio head cleaning;
4) Damage that occurs in shipment, due to an act of God, and cosmetic damage;
5) Signal reception problems and failures due to line power surge;
6) Video Pick-up Tubes/CCD Image Sensor, Cartridge, Stylus (Needle) are covered for 90
days from the date of purchase;
37
Warranty
7) Accessories;
8) Batteries (except that Rechargeable Batteries are covered for 90 days from date of
purchase.)
There are no express warranties except as listed above.
THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTY
OF MERCHANTABILTY, IS LIMITED TO THE DURATION OF THE EXPRESS WARRANTY
HEREIN.
JVC SHALL NOT BE LIABLE FOR ANY LOSS OF USE OF THE PRODUCT,
INCONVENIENCE, OR ANY OTHER DAMAGES, WHETHER DIRECT, INCIDENTAL OR
CONSEQUENTIAL (INCLUDING, WITHOUT LIMITATION, DAMAGE TO TAPES, RECORDS
OR DISCS) RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY
BREACH OF THIS WARRANTY, ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING
THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE,
ARE LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE.
Some states do not allow the exclusion of incidental or consequential damages or
limitations on how long the warranty lasts, so these exclusions or limitations may not
apply to you. This warranty gives you specific legal rights and you may also have other
rights which vary state to state.
JVC COMPANY OF AMERICA
1700 Valley Road
DIVISION OF JVC AMERICAS CORP.
Wayne, New Jersey 07470
REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY. THIS WARRANTY
DOES NOT APPLY FOR DETAILS OF REFURBISHED PRODUCT WARRANTY.
PLEASE REFER TO THE REFURBISHED PRODUCT WARRANTY INFORMATION
PACKAGED WITH EACH REFURBISHED PRODUCT.
For customer use:
Enter below the Model No. and Serial No. which is located either on the rear, bottom or
side of the cabinet.
Retain this information for future reference.
Model No.:
Serial No.:
Purchase Date:
Name Of Dealer:
38
Authorized Service Centers
QUALITY
SERVICE
HOW TO LOCATE YOUR
JVC SERVICE CENTER
TOLL FREE: 1 (800) 537-5722
Dear Customer,
In order to receive the most satisfaction from your purchase, please read the
instruction booklet before operating the unit. In the event that repairs are necessary,
please call 1 (800) 537-5722 for your nearest authorized servicer or visit our website
at www.JVC.com
Remember to retain your Bill of Sale for Warranty Service.
Do not service the television yourself
Caution
To prevent electrical shock, do not open the cabinet. There are no user serviceable
parts inside. Please refer to qualified service personnel for repairs.
Accessories
To purchase accessories for your JVC product, please call toll free:
1 (800) 882-2345 or on the web at www.JVC.com
39
Specifications
AV-27530
AV-27WR25
MODEL
Reception
Format
NTSC, BTSC System (Multi-Channel Sound)
VHF 2 to 13, UHF 14 to 69
Sub Mid, Mid, Super, Hyper and Ultra bands
(181 channel frequency synthesizer system)
Reception
Range
Power Source
AC 120V, 60Hz
105W
Power
Consumption
Screen Size
27 inch / 68 cm
measured diagonally
full square
Audio Output
Speakers
1.2W + 1.2W
2x3 1/2 / 5x9 cm oval x 2
Antenna
Terminal
75 ohms (VHF/UHF) (F-type connector)
External Input
Jacks
Video: 1 Vp-p, 75 ohms
Audio: 500mVrms (-4dBs) high impediance
S-Video Input
Jack
Y: 1Vp-p positive, 75 ohms (negative sync provided)
C: 0.286 Vp-p (burst signal), 75 ohms
Component
Input Jacks
Y: 1Vp-p positive, 75 ohms (negative sync provided)
PB/PR: 0.7 Vp-p, 75 ohms
Audio Output
Jacks (FIX)
FIX; 500 mVrms (-4dBs) Low impedance (400 Hz when modulated 100%)
Dimensions (In)
WxHxD (cm)
25 3/4 x 23 3/8 x 19 1/2
65.4 x 59.3 x 49.4
Weight (lbs / kg)
Accessories
68.5 / 31.1
Remote control unit x 1, Lithium cell battery x 1
Specifications subject to change without notice.
JVC COMPANY OF AMERICA
Division of JVC Americas Corp.
1700 Valley Road
JVC CANADA, INC.
21 Finchdene Square
Scarborough, Ontario
Canada, M1X 1A7
Wayne, New Jersey, 07470
Manuel d’instructions pour téléviseur en couleurs
Pour Les Modèles:
AV-27530
AV-27WR25
Illustration du modèle AV-27530 et RM-C203
Information importante pour l’utilisateur :
Veillez inscrire dans l’espace ci-dessous le numéro de série de votre téléviseur (situé à
l’arrière du téléviseur). Agrafez votre reçu ou votre facture à la couverture, à l’intérieur de ce
guide. Rangez ce manuel dans un lieu où vous pourrez le retrouver rapidement pour vous y
référer. Gardez le carton et l’emballage d’origine pour une utilisation ultérieure.
Numéro de modèle :
LCT1531-001A-A
Numéro de série :
0104KGI-II-IM
|