Intel 8086 User Manual

8086

16-BIT HMOS MICROPROCESSOR

8086/8086-2/8086-1

Direct Addressing Capability 1 MByte

of Memory

Range of Clock Rates:

5 MHz for 8086,

8 MHz for 8086-2,

10 MHz for 8086-1

Architecture Designed for Powerful

Assembly Language and Efficient High

Level Languages

MULTIBUS System Compatible

Interface

14 Word, by 16-Bit Register Set with

Symmetrical Operations

Available in EXPRESS

Ð Standard Temperature Range

Ð Extended Temperature Range

24 Operand Addressing Modes

Bit, Byte, Word, and Block Operations

Available in 40-Lead Cerdip and Plastic

Package

8 and 16-Bit Signed and Unsigned

Arithmetic in Binary or Decimal

Including Multiply and Divide

(See Packaging Spec. Order 231369)

The Intel 8086 high performance 16-bit CPU is available in three clock rates: 5, 8 and 10 MHz. The CPU is

implemented in N-Channel, depletion load, silicon gate technology (HMOS-III), and packaged in a 40-pin

CERDIP or plastic package. The 8086 operates in both single processor and multiple processor configurations

to achieve high performance levels.

231455–2

40 Lead

Figure 2. 8086 Pin

Configuration

231455–1

Figure 1. 8086 CPU Block Diagram

September 1990

Order Number: 231455-005

8086

Table 1. Pin Description (Continued)

Name and Function

Symbol

Pin No.

Type

READY

READY: is the acknowledgement from the addressed memory or I/O

device that it will complete the data transfer. The READY signal from

memory/IO is synchronized by the 8284A Clock Generator to form

READY. This signal is active HIGH. The 8086 READY input is not

synchronized. Correct operation is not guaranteed if the setup and hold

times are not met.

INTR

INTERRUPT REQUEST: is a level triggered input which is sampled

during the last clock cycle of each instruction to determine if the

processor should enter into an interrupt acknowledge operation. A

subroutine is vectored to via an interrupt vector lookup table located in

system memory. It can be internally masked by software resetting the

interrupt enable bit. INTR is internally synchronized. This signal is

active HIGH.

TEST

NMI

TEST: input is examined by the ‘‘Wait’’ instruction. If the TEST input is

LOW execution continues, otherwise the processor waits in an ‘‘Idle’’

state. This input is synchronized internally during each clock cycle on

the leading edge of CLK.

NON-MASKABLE INTERRUPT: an edge triggered input which causes

a type 2 interrupt. A subroutine is vectored to via an interrupt vector

lookup table located in system memory. NMI is not maskable internally

by software. A transition from LOW to HIGH initiates the interrupt at the

end of the current instruction. This input is internally synchronized.

RESET

CLK

RESET: causes the processor to immediately terminate its present

activity. The signal must be active HIGH for at least four clock cycles. It

restarts execution, as described in the Instruction Set description, when

RESET returns LOW. RESET is internally synchronized.

CLOCK: provides the basic timing for the processor and bus controller.

It is asymmetric with a 33% duty cycle to provide optimized internal

timing.

5V power supply pin.

1, 20

GND

GROUND

MN/MX

MINIMUM/MAXIMUM: indicates what mode the processor is to

operate in. The two modes are discussed in the following sections.

The following pin function descriptions are for the 8086/8288 system in maximum mode (i.e., MN/MX

Only the pin functions which are unique to maximum mode are described; all other pin functions are as

described above.

S , S , S

26–28

STATUS: active during T , T , and T and is returned to the passive state

(1, 1, 1) during T or during T when READY is HIGH. This status is used

by the 8288 Bus Controller to generate all memory and I/O access control

signals. Any change by S , S , or S during T is used to indicate the

beginning of a bus cycle, and the return to the passive state in T or T is

used to indicate the end of a bus cycle.

8086

Table 1. Pin Description (Continued)

Name and Function

Symbol

S , S , S

(Continued)

Pin No. Type

26–28

These signals float to 3-state OFF in ‘‘hold acknowledge’’. These status

lines are encoded as shown.

Characteristics

0 (LOW)

Interrupt Acknowledge

Read I/O Port

Write I/O Port

Halt

1 (HIGH)

Code Access

Read Memory

Write Memory

Passive

RQ/GT ,

RQ/GT

30, 31

I/O

REQUEST/GRANT: pins are used by other local bus masters to force

the processor to release the local bus at the end of the processor’s

current bus cycle. Each pin is bidirectional with RQ/GT having higher

priority than RQ/GT . RQ/GT pins have internal pull-up resistors and

may be left unconnected. The request/grant sequence is as follows

(see Page 2-24):

1. A pulse of 1 CLK wide from another local bus master indicates a local

bus request (‘‘hold’’) to the 8086 (pulse 1).

2. During a T or T clock cycle, a pulse 1 CLK wide from the 8086 to

the requesting master (pulse 2), indicates that the 8086 has allowed the

local bus to float and that it will enter the ‘‘hold acknowledge’’ state at

the next CLK. The CPU’s bus interface unit is disconnected logically

from the local bus during ‘‘hold acknowledge’’.

3. A pulse 1 CLK wide from the requesting master indicates to the 8086

(pulse 3) that the ‘‘hold’’ request is about to end and that the 8086 can

reclaim the local bus at the next CLK.

Each master-master exchange of the local bus is a sequence of 3

pulses. There must be one dead CLK cycle after each bus exchange.

Pulses are active LOW.

If the request is made while the CPU is performing a memory cycle, it

will release the local bus during T of the cycle when all the following

conditions are met:

1. Request occurs on or before T .

2. Current cycle is not the low byte of a word (on an odd address).

3. Current cycle is not the first acknowledge of an interrupt acknowledge

sequence.

4. A locked instruction is not currently executing.

If the local bus is idle when the request is made the two possible events

will follow:

1. Local bus will be released during the next clock.

2. A memory cycle will start within 3 clocks. Now the four rules for a

currently active memory cycle apply with condition number 1 already

satisfied.

LOCK

LOCK: output indicates that other system bus masters are not to gain

control of the system bus while LOCK is active LOW. The LOCK signal

is activated by the ‘‘LOCK’’ prefix instruction and remains active until the

completion of the next instruction. This signal is active LOW, and floats

to 3-state OFF in ‘‘hold acknowledge’’.

8086

Table 1. Pin Description (Continued)

Name and Function

Symbol

QS , QS

Pin No.

Type

24, 25

QUEUE STATUS: The queue status is valid during the CLK cycle after

which the queue operation is performed.

QS and QS provide status to allow external tracking of the internal

8086 instruction queue.

Characteristics

No Operation

0 (LOW)

First Byte of Op Code from Queue

Empty the Queue

Subsequent Byte from Queue

1 (HIGH)

functions which are unique to minimum mode are described; all other pin functions are as described above.

The following pin function descriptions are for the 8086 in minimum mode (i.e., MN/MX

). Only the pin

M/IO

STATUS LINE: logically equivalent to S in the maximum mode. It is used to

distinguish a memory access from an I/O access. M/IO becomes valid in

the T preceding a bus cycle and remains valid until the final T of the cycle

LOW). M/IO floats to 3-state OFF in local bus ‘‘hold

acknowledge’’.

HIGH, IO

WRITE: indicates that the processor is performing a write memory or write

I/O cycle, depending on the state of the M/IO signal. WR is active for T , T

and T of any write cycle. It is active LOW, and floats to 3-state OFF in

local bus ‘‘hold acknowledge’’.

INTA

ALE

INTA: is used as a read strobe for interrupt acknowledge cycles. It is active

LOW during T , T and T of each interrupt acknowledge cycle.

ADDRESS LATCH ENABLE: provided by the processor to latch the

address into the 8282/8283 address latch. It is a HIGH pulse active during

of any bus cycle. Note that ALE is never floated.

DT/R

DEN

DATA TRANSMIT/RECEIVE: needed in minimum system that desires to

use an 8286/8287 data bus transceiver. It is used to control the direction of

data flow through the transceiver. Logically DT/R is equivalent to S in the

LOW.) This signal floats to 3-state OFF in local bus ‘‘hold acknowledge’’.

maximum mode, and its timing is the same as for M/IO. (T

HIGH, R

DATA ENABLE: provided as an output enable for the 8286/8287 in a

minimum system which uses the transceiver. DEN is active LOW during

each memory and I/O access and for INTA cycles. For a read or INTA cycle

it is active from the middle of T until the middle of T , while for a write cycle

it is active from the beginning of T until the middle of T . DEN floats to 3-

state OFF in local bus ‘‘hold acknowledge’’.

HOLD,

HLDA

31, 30

I/O

HOLD: indicates that another master is requesting a local bus ‘‘hold.’’ To be

acknowledged, HOLD must be active HIGH. The processor receiving the

‘‘hold’’ request will issue HLDA (HIGH) as an acknowledgement in the

middle of a T or T clock cycle. Simultaneous with the issuance of HLDA

the processor will float the local bus and control lines. After HOLD is

detected as being LOW, the processor will LOWer the HLDA, and when the

processor needs to run another cycle, it will again drive the local bus and

control lines. Hold acknowledge (HLDA) and HOLD have internal pull-up

resistors.

The same rules as for RQ/GT apply regarding when the local bus will be

released.

HOLD is not an asynchronous input. External synchronization should be

provided if the system cannot otherwise guarantee the setup time.

8086

bytes, addressed as 00000(H) to FFFFF(H). The

memory is logically divided into code, data, extra

data, and stack segments of up to 64K bytes each,

with each segment falling on 16-byte boundaries.

(See Figure 3a.)

FUNCTIONAL DESCRIPTION

General Operation

The internal functions of the 8086 processor are

partitioned logically into two processing units. The

first is the Bus Interface Unit (BIU) and the second is

the Execution Unit (EU) as shown in the block dia-

gram of Figure 1.

All memory references are made relative to base ad-

dresses contained in high speed segment registers.

The segment types were chosen based on the ad-

dressing needs of programs. The segment register

to be selected is automatically chosen according to

the rules of the following table. All information in one

segment type share the same logical attributes (e.g.

code or data). By structuring memory into relocat-

able areas of similar characteristics and by automati-

cally selecting segment registers, programs are

shorter, faster, and more structured.

These units can interact directly but for the most

part perform as separate asynchronous operational

processors. The bus interface unit provides the func-

tions related to instruction fetching and queuing, op-

erand fetch and store, and address relocation. This

unit also provides the basic bus control. The overlap

of instruction pre-fetching provided by this unit

serves to increase processor performance through

improved bus bandwidth utilization. Up to 6 bytes of

the instruction stream can be queued while waiting

for decoding and execution.

Word (16-bit) operands can be located on even or

odd address boundaries and are thus not con-

strained to even boundaries as is the case in many

16-bit computers. For address and data operands,

the least significant byte of the word is stored in the

lower valued address location and the most signifi-

cant byte in the next higher address location. The

BIU automatically performs the proper number of

memory accesses, one if the word operand is on an

even byte boundary and two if it is on an odd byte

boundary. Except for the performance penalty, this

double access is transparent to the software. This

performance penalty does not occur for instruction

fetches, only word operands.

The instruction stream queuing mechanism allows

the BIU to keep the memory utilized very efficiently.

Whenever there is space for at least 2 bytes in the

queue, the BIU will attempt a word fetch memory

cycle. This greatly reduces ‘‘dead time’’ on the

memory bus. The queue acts as a First-In-First-Out

(FIFO) buffer, from which the EU extracts instruction

bytes as required. If the queue is empty (following a

branch instruction, for example), the first byte into

the queue immediately becomes available to the EU.

Physically, the memory is organized as a high bank

(D –D ) and a low bank (D –D ) of 512K 8-bit

The execution unit receives pre-fetched instructions

from the BIU queue and provides un-relocated oper-

and addresses to the BIU. Memory operands are

passed through the BIU for processing by the EU,

which passes results to the BIU for storage. See the

Instruction Set description for further register set

and architectural descriptions.

bytes addressed in parallel by the processor’s ad-

dress lines A –A . Byte data with even addresses

is transferred on the D –D bus lines while odd ad-

dressed byte data (A HIGH) is transferred on the

–D bus lines. The processor provides two en-

able signals, BHE and A , to selectively allow read-

ing from or writing into either an odd byte location,

even byte location, or both. The instruction stream is

fetched from memory as words and is addressed

internally by the processor to the byte level as nec-

essary.

MEMORY ORGANIZATION

The processor provides a 20-bit address to memory

which locates the byte being referenced. The memo-

ry is organized as a linear array of up to 1 million

Memory

Segment Register

Used

Segment

Reference Need

Selection Rule

Instructions

Stack

CODE (CS)

STACK (SS)

Automatic with all instruction prefetch.

All stack pushes and pops. Memory references relative to BP

base register except data references.

Local Data

DATA (DS)

Data references when: relative to stack, destination of string

operation, or explicitly overridden.

External (Global) Data EXTRA (ES)

Destination of string operations: explicitly selected using a

segment override.

8086

address FFFF0H through FFFFFH are reserved for

operations including a jump to the initial program

loading routine. Following RESET, the CPU will al-

ways begin execution at location FFFF0H where the

jump must be. Locations 00000H through 003FFH

are reserved for interrupt operations. Each of the

256 possible interrupt types has its service routine

pointed to by a 4-byte pointer element consisting of

a 16-bit segment address and a 16-bit offset ad-

dress. The pointer elements are assumed to have

been stored at the respective places in reserved

memory prior to occurrence of interrupts.

MINIMUM AND MAXIMUM MODES

The requirements for supporting minimum and maxi-

mum 8086 systems are sufficiently different that

they cannot be done efficiently with 40 uniquely de-

fined pins. Consequently, the 8086 is equipped with

a strap pin (MN/MX) which defines the system con-

figuration. The definition of a certain subset of the

pins changes dependent on the condition of the

strap pin. When MN/MX pin is strapped to GND, the

8086 treats pins 24 through 31 in maximum mode.

An 8288 bus controller interprets status information

231455–3

Figure 3a. Memory Organization

In referencing word data the BIU requires one or two

memory cycles depending on whether or not the

starting byte of the word is on an even or odd ad-

dress, respectively. Consequently, in referencing

word operands performance can be optimized by lo-

cating data on even address boundaries. This is an

especially useful technique for using the stack, since

odd address references to the stack may adversely

affect the context switching time for interrupt pro-

cessing or task multiplexing.

coded into S , S , S to generate bus timing and

control signals compatible with the MULTIBUS ar-

chitecture. When the MN/MX pin is strapped to V

the 8086 generates bus control signals itself on pins

24 through 31, as shown in parentheses in Figure 2.

Examples of minimum mode and maximum mode

systems are shown in Figure 4.

BUS OPERATION

The 8086 has a combined address and data bus

commonly referred to as a time multiplexed bus.

This technique provides the most efficient use of

pins on the processor while permitting the use of a

standard 40-lead package. This ‘‘local bus’’ can be

buffered directly and used throughout the system

with address latching provided on memory and I/O

modules. In addition, the bus can also be demulti-

plexed at the processor with a single set of address

latches if a standard non-multiplexed bus is desired

for the system.

Each processor bus cycle consists of at least four

CLK cycles. These are referred to as T , T , T and

(see Figure 5). The address is emitted from the

processor during T and data transfer occurs on the

bus during T and T . T is used primarily for chang-

231455–4

ing the direction of the bus during read operations. In

the event that a ‘‘NOT READY’’ indication is given

by the addressed device, ‘‘Wait’’ states (T ) are in-

Figure 3b. Reserved Memory Locations

Certain locations in memory are reserved for specific

CPU operations (see Figure 3b). Locations from

serted between T and T . Each inserted ‘‘Wait’’

state is of the same duration as a CLK cycle. Periods

8086

231455–5

Figure 4a. Minimum Mode 8086 Typical Configuration

231455–6

Figure 4b. Maximum Mode 8086 Typical Configuration

8086

can occur between 8086 bus cycles. These are re-

ferred to as ‘‘Idle’’ states (T ) or inactive CLK cycles.

Characteristics

The processor uses these cycles for internal house-

keeping.

0 (LOW)

Interrupt Acknowledge

Read I/O

During T of any bus cycle the ALE (Address Latch

Write I/O

Enable) signal is emitted (by either the processor or

the 8288 bus controller, depending on the MN/MX

strap). At the trailing edge of this pulse, a valid ad-

dress and certain status information for the cycle

may be latched.

Halt

1 (HIGH)

Instruction Fetch

Read Data from Memory

Write Data to Memory

Passive (no bus cycle)

Status bits S , S , and S are used, in maximum

mode, by the bus controller to identify the type of

bus transaction according to the following table:

231455–8

Figure 5. Basic System Timing

8086

Status bits S through S are multiplexed with high-

NMI asserted prior to the 2nd clock after the end of

RESET will not be honored. If NMI is asserted after

that point and during the internal reset sequence,

the processor may execute one instruction before

responding to the interrupt. A hold request active

immediately after RESET will be honored before the

first instruction fetch.

order address bits and the BHE signal, and are

therefore valid during T through T . S and S indi-

cate which segment register (see Instruction Set de-

scription) was used for this bus cycle in forming the

address, according to the following table:

Characteristics

Alternate Data (extra segment)

Stack

All 3-state outputs float to 3-state OFF during

RESET. Status is active in the idle state for the first

clock after RESET becomes active and then floats

to 3-state OFF. ALE and HLDA are driven low.

0 (LOW)

1 (HIGH)

Code or None

Data

INTERRUPT OPERATIONS

is a reflection of the PSW interrupt enable bit.

Interrupt operations fall into two classes; software or

hardware initiated. The software initiated interrupts

and software aspects of hardware interrupts are

specified in the Instruction Set description. Hard-

ware interrupts can be classified as non-maskable or

maskable.

0 and S is a spare status bit.

I/O ADDRESSING

In the 8086, I/O operations can address up to a

maximum of 64K I/O byte registers or 32K I/O word

registers. The I/O address appears in the same for-

mat as the memory address on bus lines A –A .

Interrupts result in a transfer of control to a new pro-

gram location. A 256-element table containing ad-

dress pointers to the interrupt service program loca-

tions resides in absolute locations 0 through 3FFH

(see Figure 3b), which are reserved for this purpose.

Each element in the table is 4 bytes in size and

corresponds to an interrupt ‘‘type’’. An interrupting

device supplies an 8-bit type number, during the in-

terrupt acknowledge sequence, which is used to

‘‘vector’’ through the appropriate element to the new

interrupt service program location.

The address lines A –A are zero in I/O opera-

tions. The variable I/O instructions which use regis-

ter DX as a pointer have full address capability while

the direct I/O instructions directly address one or

two of the 256 I/O byte locations in page 0 of the

I/O address space.

I/O ports are addressed in the same manner as

memory locations. Even addressed bytes are trans-

ferred on the D –D bus lines and odd addressed

bytes on D –D . Care must be taken to assure that

each register within an 8-bit peripheral located on

the lower portion of the bus be addressed as even.

NON-MASKABLE INTERRUPT (NMI)

The processor provides a single non-maskable inter-

rupt pin (NMI) which has higher priority than the

maskable interrupt request pin (INTR). A typical use

would be to activate a power failure routine. The

NMI is edge-triggered on a LOW-to-HIGH transition.

The activation of this pin causes a type 2 interrupt.

(See Instruction Set description.)

External Interface

PROCESSOR RESET AND INITIALIZATION

Processor initialization or start up is accomplished

with activation (HIGH) of the RESET pin. The 8086

RESET is required to be HIGH for greater than 4

CLK cycles. The 8086 will terminate operations on

the high-going edge of RESET and will remain dor-

mant as long as RESET is HIGH. The low-going

transition of RESET triggers an internal reset se-

quence for approximately 10 CLK cycles. After this

interval the 8086 operates normally beginning with

the instruction in absolute location FFFF0H (see Fig-

ure 3b). The details of this operation are specified in

the Instruction Set description of the MCS-86 Family

User’s Manual. The RESET input is internally syn-

chronized to the processor clock. At initialization the

HIGH-to-LOW transition of RESET must occur no

sooner than 50 ms after power-up, to allow complete

initialization of the 8086.

NMI is required to have a duration in the HIGH state

of greater than two CLK cycles, but is not required to

be synchronized to the clock. Any high-going tran-

sition of NMI is latched on-chip and will be serviced

at the end of the current instruction or between

whole moves of a block-type instruction. Worst case

response to NMI would be for multiply, divide, and

variable shift instructions. There is no specification

on the occurrence of the low-going edge; it may oc-

cur before, during, or after the servicing of NMI. An-

other high-going edge triggers another response if it

occurs after the start of the NMI procedure. The sig-

nal must be free of logical spikes in general and be

free of bounces on the low-going edge to avoid trig-

gering extraneous responses.

8086

MASKABLE INTERRUPT (INTR)

HALT

The 8086 provides a single interrupt request input

(INTR) which can be masked internally by software

with the resetting of the interrupt enable FLAG

status bit. The interrupt request signal is level trig-

gered. It is internally synchronized during each clock

cycle on the high-going edge of CLK. To be re-

sponded to, INTR must be present (HIGH) during

the clock period preceding the end of the current

instruction or the end of a whole move for a block-

type instruction. During the interrupt response se-

quence further interrupts are disabled. The enable

bit is reset as part of the response to any interrupt

(INTR, NMI, software interrupt or single-step), al-

though the FLAGS register which is automatically

pushed onto the stack reflects the state of the proc-

essor prior to the interrupt. Until the old FLAGS reg-

ister is restored the enable bit will be zero unless

specifically set by an instruction.

When a software ‘‘HALT’’ instruction is executed the

processor indicates that it is entering the ‘‘HALT’’

state in one of two ways depending upon which

mode is strapped. In minimum mode, the processor

issues one ALE with no qualifying bus control sig-

nals. In maximum mode, the processor issues ap-

propriate HALT status on S , S , and S ; and the

8288 bus controller issues one ALE. The 8086 will

not leave the ‘‘HALT’’ state when a local bus ‘‘hold’’

is entered while in ‘‘HALT’’. In this case, the proces-

sor reissues the HALT indicator. An interrupt request

or RESET will force the 8086 out of the ‘‘HALT’’

state.

READ/MODIFY/WRITE (SEMAPHORE)

OPERATIONS VIA LOCK

The LOCK status information is provided by the

processor when directly consecutive bus cycles are

required during the execution of an instruc-

tion. This provides the processor with the capability

of performing read/modify/write operations on

memory (via the Exchange Register With Memory

instruction, for example) without the possibility of an-

other system bus master receiving intervening mem-

ory cycles. This is useful in multi-processor system

configurations to accomplish ‘‘test and set lock’’ op-

erations. The LOCK signal is activated (forced LOW)

in the clock cycle following the one in which the soft-

ware ‘‘LOCK’’ prefix instruction is decoded by the

EU. It is deactivated at the end of the last bus cycle

of the instruction following the ‘‘LOCK’’ prefix in-

struction. While LOCK is active a request on a RQ/

GT pin will be recorded and then honored at the end

of the LOCK.

During the response sequence (Figure 6) the proc-

essor executes two successive (back-to-back) inter-

rupt acknowledge cycles. The 8086 emits the LOCK

signal from T of the first bus cycle until T of the

second. A local bus ‘‘hold’’ request will not be hon-

ored until the end of the second bus cycle. In the

second bus cycle a byte is fetched from the external

interrupt system (e.g., 8259A PIC) which identifies

the source (type) of the interrupt. This byte is multi-

plied by four and used as a pointer into the interrupt

vector lookup table. An INTR signal left HIGH will be

continually responded to within the limitations of the

enable bit and sample period. The INTERRUPT RE-

TURN instruction includes a FLAGS pop which re-

turns the status of the original interrupt enable bit

when it restores the FLAGS.

231455–9

Figure 6. Interrupt Acknowledge Sequence

8086

EXTERNAL SYNCHRONIZATION VIA TEST

SYSTEM TIMINGÐMINIMUM SYSTEM

As an alternative to the interrupts and general I/O

capabilities, the 8086 provides a single software-

testable input known as the TEST signal. At any time

the program may execute a WAIT instruction. If at

that time the TEST signal is inactive (HIGH), pro-

gram execution becomes suspended while the proc-

essor waits for TEST to become active. It must

remain active for at least 5 CLK cycles. The WAIT

instruction is re-executed repeatedly until that time.

This activity does not consume bus cycles. The

processor remains in an idle state while waiting. All

8086 drivers go to 3-state OFF if bus ‘‘Hold’’ is en-

tered. If interrupts are enabled, they may occur while

the processor is waiting. When this occurs the proc-

essor fetches the WAIT instruction one extra time,

processes the interrupt, and then re-fetches and re-

executes the WAIT instruction upon returning from

the interrupt.

The read cycle begins in T with the assertion of the

Address Latch Enable (ALE) signal. The trailing (low-

going) edge of this signal is used to latch the ad-

dress information, which is valid on the local bus at

this time, into the address latch. The BHE and A

signals address the low, high, or both bytes. From T

to T the M/IO signal indicates a memory or I/O

operation. At T the address is removed from the

local bus and the bus goes to a high impedance

state. The read control signal is also asserted at T .

The read (RD) signal causes the addressed device

to enable its data bus drivers to the local bus. Some

time later valid data will be available on the bus and

the addressed device will drive the READY line

HIGH. When the processor returns the read signal to

a HIGH level, the addressed device will again 3-

state its bus drivers. If a transceiver is required to

buffer the 8086 local bus, signals DT/R and DEN

are provided by the 8086.

A write cycle also begins with the assertion of ALE

and the emission of the address. The M/IO signal is

again asserted to indicate a memory or I/O write

Basic System Timing

Typical system configurations for the processor op-

erating in minimum mode and in maximum mode are

shown in Figures 4a and 4b, respectively. In mini-

operation. In the T immediately following the ad-

dress emission the processor emits the data to be

written into the addressed location. This data re-

mains valid until the middle of T . During T , T , and

mum mode, the MN/MX pin is strapped to V

and

the processor emits bus control signals in a manner

similar to the 8085. In maximum mode, the MN/MX

pin is strapped to V and the processor emits cod-

the processor asserts the write control signal.

The write (WR) signal becomes active at the begin-

ning of T as opposed to the read which is delayed

somewhat into T to provide time for the bus to float.

ed status information which the 8288 bus controller

uses to generate MULTIBUS compatible bus control

signals. Figure 5 illustrates the signal timing relation-

ships.

The BHE and A signals are used to select the prop-

er byte(s) of the memory/IO word to be read or writ-

ten according to the following table:

BHE

Characteristics

Whole word

Upper byte from/to

odd address

Lower byte from/to

even address

None

I/O ports are addressed in the same manner as

memory location. Even addressed bytes are trans-

ferred on the D –D bus lines and odd addressed

bytes on D –D .

The basic difference between the interrupt acknowl-

edge cycle and a read cycle is that the interrupt ac-

knowledge signal (INTA) is asserted in place of the

read (RD) signal and the address bus is floated.

(See Figure 6.) In the second of two successive

INTA cycles, a byte of information is read from bus

231455–10

Figure 7. 8086 Register Model

8086

lines D –D as supplied by the inerrupt system logic

acknowledge, or software halt. The 8288 thus issues

control signals specifying memory read or write, I/O

read or write, or interrupt acknowledge. The 8288

provides two types of write strobes, normal and ad-

vanced, to be applied as required. The normal write

strobes have data valid at the leading edge of write.

The advanced write strobes have the same timing

as read strobes, and hence data isn’t valid at the

leading edge of write. The transceiver receives the

usual DIR and G inputs from the 8288’s DT/R and

DEN.

(i.e., 8259A Priority Interrupt Controller). This byte

identifies the source (type) of the interrupt. It is multi-

plied by four and used as a pointer into an interrupt

vector lookup table, as described earlier.

BUS TIMINGÐMEDIUM SIZE SYSTEMS

For medium size systems the MN/MX pin is con-

nected to V and the 8288 Bus Controller is added

to the system as well as a latch for latching the sys-

tem address, and a transceiver to allow for bus load-

ing greater than the 8086 is capable of handling.

Signals ALE, DEN, and DT/R are generated by the

8288 instead of the processor in this configuration

although their timing remains relatively the same.

The pointer into the interrupt vector table, which is

passed during the second INTA cycle, can derive

from an 8259A located on either the local bus or the

system bus. If the master 8259A Priority Interrupt

Controller is positioned on the local bus, a TTL gate

is required to disable the transceiver when reading

from the master 8259A during the interrupt acknowl-

edge sequence and software ‘‘poll’’.

The 8086 status outputs (S , S , and S ) provide

type-of-cycle information and become 8288 inputs.

This bus cycle information specifies read (code,

data, or I/O), write (data or I/O), interrupt

8086

ABSOLUTE MAXIMUM RATINGS*

NOTICE: This is a production data sheet. The specifi-

cations are subject to change without notice.

Ambient Temperature Under Bias ÀÀÀÀÀÀ0 C to 70 C

Storage Temperature ÀÀÀÀÀÀÀÀÀÀ 65 C to 150 C

*WARNING: Stressing the device beyond the ‘‘Absolute

Maximum Ratings’’ may cause permanent damage.

These are stress ratings only. Operation beyond the

‘‘Operating Conditions’’ is not recommended and ex-

tended exposure beyond the ‘‘Operating Conditions’’

may affect device reliability.

Voltage on Any Pin with

Respect to GroundÀÀÀÀÀÀÀÀÀÀÀÀÀÀ 1.0V to 7V

Power DissipationÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ2.5W

D.C. CHARACTERISTICS (8086:

(8086-1: T

0 C to 70 C, V

5V 10%)

0 C to 70 C, V

5V 5%)

(8086-2: T

0 C to 70 C, V

Symbol

Parameter

Input Low Voltage

Input High Voltage

Output Low Voltage

Output High Voltage

Min

Max

Units

Test Conditions

(Note 1)

0.8

0.5

2.0

0.5

(Notes 1, 2)

0.45

2.5 mA

e b

2.4

400 mA

Power Supply Current: 8086

8086-1

8086-2

340

360

350

25 C

Input Leakage Current

Output Leakage Current

Clock Input Low Voltage

Clock Input High Voltage

(Note 3)

0.45V

OUT

0.5

0.6

3.9

1.0

Capacitance of Input Buffer

(All input except

AD –AD , RQ/GT)

1 MHz

Capacitance of I/O Buffer

(AD –AD , RQ/GT)

NOTES:

1. V tested with MN/MX Pin

0V. V tested with MN/MX Pin

5V. MN/MX Pin is a Strap Pin.

2. Not applicable to RQ/GT0 and RQ/GT1 (Pins 30 and 31).

3. HOLD and HLDA I min

30 mA, max

500 mA.

8086

A.C. CHARACTERISTICS (8086:

0 C to 70 C, V

5V 10%)

(8086-1: T

(8086-2: T

0 C to 70 C, V

5V 5%)

0 C to 70 C, V

MINIMUM COMPLEXITY SYSTEM TIMING REQUIREMENTS

8086

8086-1

8086-2

Symbol

Parameter

Units

Test Conditions

Min Max

Min

100

Max Min Max

TCLCL

TCLCH

TCHCL

CLK Cycle Period

CLK Low Time

CLK High Time

200

118

500

125

500

TCH1CH2 CLK Rise Time

From 1.0V to 3.5V

From 3.5V to 1.0V

TCL2CL1

TDVCL

CLK Fall Time

Data in Setup Time

Data in Hold Time

TCLDX

TR1VCL

RDY Setup Time

into 8284A (See

Notes 1, 2)

TCLR1X

RDY Hold Time

into 8284A (See

Notes 1, 2)

TRYHCH

TCHRYX

TRYLCL

READY Setup

Time into 8086

118

READY Hold Time

into 8086

READY Inactive to

CLK (See Note 3)

THVCH

TINVCH

HOLD Setup Time

INTR, NMI, TEST

Setup Time (See

Note 2)

TILIH

TIHIL

Input Rise Time

(Except CLK)

From 0.8V to 2.0V

From 2.0V to 0.8V

Input Fall Time

(Except CLK)

8086

A.C. CHARACTERISTICS (Continued)

TIMING RESPONSES

8086

8086-1

Min

8086-2

Min

Test

Symbol

Parameter

Units

Conditions

Min

Max

TCLAV Address Valid Delay

TCLAX Address Hold Time

110

TCLAZ Address Float

Delay

TCLAX

TLHLL

ALE Width

TCLCH-20

TCLCH-10

TCLLH ALE Active Delay

TCHLL ALE Inactive Delay

TLLAX Address Hold Time TCHCL-10

TCHCL-10

TCLDV Data Valid Delay

TCHDX Data Hold Time

110

ns *C

20–100 pF

for all 8086

Outputs (In

addition to 8086

selfload)

TWHDX Data Hold Time

After WR

TCLCH-30

TCLCH-25

TCLCH-30

TCVCTV Control Active

Delay 1

110

TCHCTV Control Active

Delay 2

TCVCTX Control Inactive

Delay

TAZRL Address Float to

READ Active

TCLRL RD Active Delay

TCLRH RD Inactive Delay

165

150

100 ns

TRHAV RD Inactive to Next TCLCL-45

Address Active

TCLCL-35

TCLCL-40

TCLHAV HLDA Valid Delay

TRLRH RD Width

160

100 ns

2TCLCL-75

2TCLCL-60

TCLCH-60

2TCLCL-40

2TCLCL-35

TCLCH-35

2TCLCL-50

2TCLCL-40

TCLCH-40

TWLWH WR Width

TAVAL Address Valid to

ALE Low

TOLOH Output Rise Time

TOHOL Output Fall Time

ns From 0.8V to 2.0V

ns From 2.0V to 0.8V

NOTES:

1. Signal at 8284A shown for reference only.

2. Setup requirement for asynchronous signal only to guarantee recognition at next CLK.

3. Applies only to T2 state. (8 ns into T3).

8086

A.C. TESTING INPUT, OUTPUT WAVEFORM

A.C. TESTING LOAD CIRCUIT

231455-11

A.C. Testing: Inputs are driven at 2.4V for a Logic ‘‘1’’ and 0.45V

for a Logic ‘‘0’’. Timing measurements are made at 1.5V for both

a Logic ‘‘1’’ and ‘‘0’’.

231455–12

Includes Jig Capacitance

WAVEFORMS

MINIMUM MODE

231455–13

8086

WAVEFORMS (Continued)

MINIMUM MODE (Continued)

231455–14

SOFTWARE HALTÐ

DT/R

RD, WR, INTA

INDETERMINATE

NOTES:

1. All signals switch between V

and V unless otherwise specified.

2. RDY is sampled near the end of T , T , T to determine if T machines states are to be inserted.

3. Two INTA cycles run back-to-back. The 8086 LOCAL ADDR/DATA BUS is floating during both INTA cycles. Control

signals shown for second INTA cycle.

4. Signals at 8284A are shown for reference only.

5. All timing measurements are made at 1.5V unless otherwise noted.

8086

A.C. CHARACTERISTICS

MAX MODE SYSTEM (USING 8288 BUS CONTROLLER)

TIMING REQUIREMENTS

8086

8086-1

8086-2

Test

Symbol

Parameter

Units

Conditions

Min Max

Min

100

Max Min Max

TCLCL

TCLCH

TCHCL

CLK Cycle Period

CLK Low Time

CLK High Time

200

118

500

125

500

TCH1CH2 CLK Rise Time

From 1.0V to 3.5V

From 3.5V to 1.0V

TCL2CL1

TDVCL

CLK Fall Time

Data in Setup Time

Data in Hold Time

TCLDX

TR1VCL

RDY Setup Time

into 8284A

(Notes 1, 2)

TCLR1X

RDY Hold Time

into 8284A

(Notes 1, 2)

TRYHCH

TCHRYX

TRYLCL

TINVCH

READY Setup

Time into 8086

118

READY Hold Time

into 8086

READY Inactive to

CLK (Note 4)

Setup Time for

Recognition (INTR,

NMI, TEST)

(Note 2)

TGVCH

TCHGX

TILIH

RQ/GT Setup Time

(Note 5)

RQ Hold Time into

8086

Input Rise Time

(Except CLK)

From 0.8V to 2.0V

From 2.0V to 0.8V

TIHIL

Input Fall Time

(Except CLK)

8086

A.C. CHARACTERISTICS (Continued)

TIMING RESPONSES

8086

8086-1

8086-2

Test

Symbol

TCLML

TCLMH

Parameter

Units

Conditions

Min

Max Min Max

Min

Max

Command Active

Delay (See Note 1)

Command Inactive

Delay (See Note 1)

TRYHSH READY Active to

Status Passive (See

Note 3)

110

TCHSV

TCLSH

Status Active Delay

110

130

Status Inactive

Delay

TCLAV

TCLAX

TCLAZ

TSVLH

Address Valid Delay

Address Hold Time

110

Address Float Delay TCLAX

TCLAX

Status Valid to ALE

High (See Note 1)

TSVMCH Status Valid to

MCE High (See

Note 1)

TCLLH

CLK Low to ALE

Valid (See Note 1)

20–100 pF

for all 8086

Outputs (In

addition to 8086

self-load)

TCLMCH CLK Low to MCE

High (See Note 1)

TCHLL

ALE Inactive Delay

(See Note 1)

TCLMCL MCE Inactive Delay

(See Note 1)

TCLDV

TCHDX

TCVNV

Data Valid Delay

Data Hold Time

110

Control Active

Delay (See Note 1)

TCVNX

TAZRL

Control Inactive

Delay (See Note 1)

Address Float to

READ Active

TCLRL

TCLRH

RD Active Delay

RD Inactive Delay

165

150

100

8086

A.C. CHARACTERISTICS (Continued)

TIMING RESPONSES (Continued)

8086

8086-1

Min

8086-2

Min

Test

Conditions

Symbol

Parameter

Units

Min

Max

TRHAV RD Inactive to Next TCLCL-45

Address Active

TCLCL-35

TCLCL-40

TCHDTL Direction Control

Active Delay

(Note 1)

20–100 pF

for all 8086

Outputs (In

addition to 8086

self-load)

TCHDTH Direction Control

Inactive Delay

(Note 1)

TCLGL GT Active Delay

TCLGH GT Inactive Delay

TRLRH RD Width

2TCLCL-75

2TCLCL-40

2TCLCL-50

TOLOH Output Rise Time

TOHOL Output Fall Time

ns From 0.8V to 2.0V

ns From 2.0V to 0.8V

NOTES:

1. Signal at 8284A or 8288 shown for reference only.

2. Setup requirement for asynchronous signal only to guarantee recognition at next CLK.

3. Applies only to T3 and wait states.

4. Applies only to T2 state (8 ns into T3).

8086

WAVEFORMS

MAXIMUM MODE

231455–15

8086

WAVEFORMS (Continued)

MAXIMUM MODE (Continued)

231455–16

NOTES:

1. All signals switch between V

and V unless otherwise specified.

2. RDY is sampled near the end of T , T , T to determine if T machines states are to be inserted.

3. Cascade address is valid between first and second INTA cycle.

4. Two INTA cycles run back-to-back. The 8086 LOCAL ADDR/DATA BUS is floating during both INTA cycles. Control for

pointer address is shown for second INTA cycle.

5. Signals at 8284A or 8288 are shown for reference only.

6. The issuance of the 8288 command and control signals (MRDC, MWTC, AMWC, IORC, IOWC, AIOWC, INTA and DEN)

lags the active high 8288 CEN.

7. All timing measurements are made at 1.5V unless otherwise noted.

8. Status inactive in state just prior to T .

8086

WAVEFORMS (Continued)

ASYNCHRONOUS SIGNAL RECOGNITION

231455–17

NOTE:

1. Setup requirements for asynchronous signals only to guarantee recognition at next CLK.

BUS LOCK SIGNAL TIMING (MAXIMUM MODE

ONLY)

RESET TIMING

231455–18

231455–19

REQUEST/GRANT SEQUENCE TIMING (MAXIMUM MODE ONLY)

231455–20

NOTE:

The coprocessor may not drive the buses outside the region shown without risking contention.

8086

WAVEFORMS (Continued)

HOLD/HOLD ACKNOWLEDGE TIMING (MINIMUM MODE ONLY)

231455–21

8086

Table 2. Instruction Set Summary

Mnemonic and

Description

Instruction Code

DATA TRANSFER

MOV

Move:

7 6 5 4 3 2 1 0

1 0 0 0 1 0 d w

1 1 0 0 0 1 1 w

1 0 1 1 w reg

7 6 5 4 3 2 1 0

Immediate to Register/Memory

Immediate to Register

mod reg r/m

mod 0 0 0 r/m

data

data if w

Memory to Accumulator

1 0 1 0 0 0 0 w

1 0 1 0 0 0 1 w

1 0 0 0 1 1 1 0

1 0 0 0 1 1 0 0

addr-low

addr-high

Accumulator to Memory

addr-low

Segment Register to Register/Memory

mod 0 reg r/m

PUSH

Push:

1 1 1 1 1 1 1 1

0 1 0 1 0 reg

0 0 0 reg 1 1 0

mod 1 1 0 r/m

Segment Register

POP

Pop:

1 0 0 0 1 1 1 1

0 1 0 1 1 reg

0 0 0 reg 1 1 1

mod 0 0 0 r/m

Segment Register

XCHG

Exchange:

1 0 0 0 0 1 1 w

1 0 0 1 0 reg

mod reg r/m

Input from:

Fixed Port

1 1 1 0 0 1 0 w

1 1 1 0 1 1 0 w

port

Variable Port

OUT

Output to:

Fixed Port

1 1 1 0 0 1 1 w

1 1 1 0 1 1 1 w

1 1 0 1 0 1 1 1

1 0 0 0 1 1 0 1

1 1 0 0 0 1 0 1

1 1 0 0 0 1 0 0

1 0 0 1 1 1 1 1

1 0 0 1 1 1 1 0

1 0 0 1 1 1 0 0

1 0 0 1 1 1 0 1

port

Variable Port

XLAT

Translate Byte to AL

LEA

LDS

LES

Load EA to Register

Load Pointer to DS

Load Pointer to ES

mod reg r/m

LAHF

SAHF

Load AH with Flags

Store AH into Flags

PUSHF

Push Flags

Pop Flags

POPF

Mnemonics

Intel, 1978

8086

Table 2. Instruction Set Summary (Continued)

Mnemonic and

Description

Instruction Code

ARITHMETIC

7 6 5 4 3 2 1 0

ADD

Add:

Reg./Memory with Register to Either

Immediate to Register/Memory

Immediate to Accumulator

0 0 0 0 0 0 d w

1 0 0 0 0 0 s w

0 0 0 0 0 1 0 w

mod reg r/m

mod 0 0 0 r/m

data

data if s: w

data if w

ADC

Add with Carry:

Reg./Memory with Register to Either

Immediate to Register/Memory

Immediate to Accumulator

0 0 0 1 0 0 d w

1 0 0 0 0 0 s w

0 0 0 1 0 1 0 w

mod reg r/m

mod 0 1 0 r/m

data

data if s: w

data if w

INC

Increment:

1 1 1 1 1 1 1 w

0 1 0 0 0 reg

mod 0 0 0 r/m

AAA

BAA

SUB

ASCII Adjust for Add

Decimal Adjust for Add

Subtract:

0 0 1 1 0 1 1 1

0 0 1 0 0 1 1 1

Reg./Memory and Register to Either

Immediate from Register/Memory

Immediate from Accumulator

0 0 1 0 1 0 d w

1 0 0 0 0 0 s w

0 0 1 0 1 1 0 w

mod reg r/m

mod 1 0 1 r/m

data

data if s w

data if w

SSB

Subtract with Borrow

Reg./Memory and Register to Either

Immediate from Register/Memory

Immediate from Accumulator

0 0 0 1 1 0 d w

1 0 0 0 0 0 s w

0 0 0 1 1 1 w

mod reg r/m

mod 0 1 1 r/m

data

data if s w

data if w

DEC

Decrement:

1 1 1 1 1 1 1 w

0 1 0 0 1 reg

1 1 1 1 0 1 1 w

mod 0 0 1 r/m

mod 0 1 1 r/m

NEG

CMP

Change sign

Compare:

Immediate with Register/Memory

Immediate with Accumulator

0 0 1 1 1 0 d w

1 0 0 0 0 0 s w

0 0 1 1 1 1 0 w

0 0 1 1 1 1 1 1

0 0 1 0 1 1 1 1

1 1 1 1 0 1 1 w

1 1 0 1 0 1 0 0

1 1 1 1 0 1 1 w

1 1 0 1 0 1 0 1

1 0 0 1 1 0 0 0

1 0 0 1 1 0 0 1

mod reg r/m

mod 1 1 1 r/m

data

data if s w

data if w

AAS

DAS

MUL

ASCII Adjust for Subtract

Decimal Adjust for Subtract

Multiply (Unsigned)

mod 1 0 0 r/m

mod 1 0 1 r/m

0 0 0 0 1 0 1 0

mod 1 1 0 r/m

mod 1 1 1 r/m

0 0 0 0 1 0 1 0

IMUL

AAM

Integer Multiply (Signed)

ASCII Adjust for Multiply

DIV

Divide (Unsigned)

IDIV

AAD

CBW

CWD

Integer Divide (Signed)

ASCII Adjust for Divide

Convert Byte to Word

Convert Word to Double Word

Mnemonics

Intel, 1978

8086

Table 2. Instruction Set Summary (Continued)

Mnemonic and

Description

Instruction Code

LOGIC

7 6 5 4 3 2 1 0

1 1 1 1 0 1 1 w

1 1 0 1 0 0 v w

7 6 5 4 3 2 1 0

mod 0 1 0 r/m

mod 1 0 0 r/m

mod 1 0 1 r/m

mod 1 1 1 r/m

mod 0 0 0 r/m

mod 0 0 1 r/m

mod 0 1 0 r/m

mod 0 1 1 r/m

7 6 5 4 3 2 1 0

NOT

Invert

SHL/SAL

Shift Logical/Arithmetic Left

SHR

SAR

ROL

ROR

RCL

RCR

Shift Logical Right

Shift Arithmetic Right

Rotate Left

Rotate Right

Rotate Through Carry Flag Left

Rotate Through Carry Right

AND

And:

Reg./Memory and Register to Either

Immediate to Register/Memory

Immediate to Accumulator

0 0 1 0 0 0 d w

1 0 0 0 0 0 0 w

0 0 1 0 0 1 0 w

mod reg r/m

mod 1 0 0 r/m

data

data if w

TEST

And Function to Flags, No Result:

1 0 0 0 0 1 0 w

mod reg r/m

Immediate Data and Register/Memory

Immediate Data and Accumulator

1 1 1 1 0 1 1 w

1 0 1 0 1 0 0 w

mod 0 0 0 r/m

data

data if w

Or:

Reg./Memory and Register to Either

Immediate to Register/Memory

Immediate to Accumulator

0 0 0 0 1 0 d w

1 0 0 0 0 0 0 w

0 0 0 0 1 1 0 w

mod reg r/m

mod 0 0 1 r/m

data

data if w

XOR

Exclusive or:

Reg./Memory and Register to Either

Immediate to Register/Memory

Immediate to Accumulator

0 0 1 1 0 0 d w

1 0 0 0 0 0 0 w

0 0 1 1 0 1 0 w

mod reg r/m

mod 1 1 0 r/m

data

data if w

STRING MANIPULATION

REP

Repeat

1 1 1 1 0 0 1 z

1 0 1 0 0 1 0 w

1 0 1 0 0 1 1 w

1 0 1 0 1 1 1 w

1 0 1 0 1 1 0 w

1 0 1 0 1 0 1 w

MOVS

CMPS

SCAS

LODS

STOS

Move Byte/Word

Compare Byte/Word

Scan Byte/Word

Load Byte/Wd to AL/AX

Stor Byte/Wd from AL/A

CONTROL TRANSFER

CALL

Call:

Direct within Segment

Indirect within Segment

Direct Intersegment

1 1 1 0 1 0 0 0

1 1 1 1 1 1 1 1

1 0 0 1 1 0 1 0

disp-low

mod 0 1 0 r/m

offset-low

disp-high

offset-high

seg-high

seg-low

Indirect Intersegment

1 1 1 1 1 1 1 1

mod 0 1 1 r/m

Mnemonics

Intel, 1978

8086

Table 2. Instruction Set Summary (Continued)

Mnemonic and

Description

Instruction Code

JMP

Unconditional Jump:

7 6 5 4 3 2 1 0

1 1 1 0 1 0 0 1

1 1 1 0 1 0 1 1

1 1 1 1 1 1 1 1

1 1 1 0 1 0 1 0

7 6 5 4 3 2 1 0

disp-low

7 6 5 4 3 2 1 0

Direct within Segment

Direct within Segment-Short

Indirect within Segment

Direct Intersegment

disp-high

disp

mod 1 0 0 r/m

offset-low

seg-low

offset-high

seg-high

Indirect Intersegment

1 1 1 1 1 1 1 1

mod 1 0 1 r/m

RET

Return from CALL:

Within Segment

1 1 0 0 0 0 1 1

1 1 0 0 0 0 1 0

1 1 0 0 1 0 1 1

1 1 0 0 1 0 1 0

0 1 1 1 0 1 0 0

0 1 1 1 1 1 0 0

Within Seg Adding Immed to SP

Intersegment

data-low

data-high

Intersegment Adding Immediate to SP

data-low

disp

JE/JZ

Jump on Equal/Zero

JL/JNGE

Jump on Less/Not Greater

or Equal

disp

JLE/JNG

Jump on Less or Equal/

Not Greater

0 1 1 1 1 1 1 0

0 1 1 1 0 0 1 0

disp

JB/JNAE

JBE/JNA

Jump on Below/Not Above

or Equal

Jump on Below or Equal/

Not Above

0 1 1 1 0 1 1 0

0 1 1 1 1 0 1 0

0 1 1 1 0 0 0 0

0 1 1 1 1 0 0 0

0 1 1 1 0 1 0 1

disp

JP/JPE

Jump on Parity/Parity Even

Jump on Overflow

Jump on Sign

JNE/JNZ

JNL/JGE

Jump on Not Equal/Not Zero

Jump on Not Less/Greater

or Equal

0 1 1 1 1 1 0 1

0 1 1 1 1 1 1 1

0 1 1 1 0 0 1 1

disp

JNLE/JG

JNB/JAE

JNBE/JA

JNP/JPO

Jump on Not Less or Equal/

Greater

Jump on Not Below/Above

or Equal

Jump on Not Below or

Equal/Above

0 1 1 1 0 1 1 1

0 1 1 1 1 0 1 1

0 1 1 1 0 0 0 1

0 1 1 1 1 0 0 1

1 1 1 0 0 0 1 0

1 1 1 0 0 0 0 1

disp

Jump on Not Par/Par Odd

JNO

JNS

Jump on Not Overflow

Jump on Not Sign

LOOP

Loop CX Times

LOOPZ/LOOPE

Loop While Zero/Equal

LOOPNZ/LOOPNE

Loop While Not

Zero/Equal

1 1 1 0 0 0 0 0

1 1 1 0 0 0 1 1

disp

JCXZ

Jump on CX Zero

Interrupt

INT

Type Specified

Type 3

1 1 0 0 1 1 0 1

1 1 0 0 1 1 0 0

1 1 0 0 1 1 1 0

1 1 0 0 1 1 1 1

type

INTO

IRET

Interrupt on Overflow

Interrupt Return

8086

Table 2. Instruction Set Summary (Continued)

Mnemonic and

Description

Instruction Code

7 6 5 4 3 2 1 0

PROCESSOR CONTROL

CLC

CMC

STC

CLD

STD

Clear Carry

1 1 1 1 1 0 0 0

1 1 1 1 0 1 0 1

1 1 1 1 1 0 0 1

1 1 1 1 1 1 0 0

1 1 1 1 1 1 0 1

1 1 1 1 1 0 1 0

1 1 1 1 1 0 1 1

1 1 1 1 0 1 0 0

1 0 0 1 1 0 1 1

1 1 0 1 1 x x x

1 1 1 1 0 0 0 0

Complement Carry

Set Carry

Clear Direction

Set Direction

CLI

STI

Clear Interrupt

Set Interrupt

HLT

Halt

WAIT

Wait

ESC

Escape (to External Device)

mod x x x r/m

LOCK

Bus Lock Prefix

NOTES:

if s w

and

if s w

01 then 16 bits of immediate data form the oper-

11 then an immediate data byte is sign extended

8-bit accumulator

16-bit accumulator

Count register

Data segment

Extra segment

to form the 16-bit operand

if v

0 then ‘‘count’’

don’t care

z is used for string primitives for comparison with ZF FLAG

1; if v

1 then ‘‘count’’ in (CL)

Above/below refers to unsigned value

Less

Greater

more positive;

less positive (more negative) signed values

SEGMENT OVERRIDE PREFIX

1 then word instruction; if w

if d

if w

1 then ‘‘to’’ reg; if d

0 then ‘‘from’’ reg

0 0 1 reg 1 1 0

0 then byte instruc-

REG is assigned according to the following table:

tion

if mod

11 then r/m is treated as a REG field

16-Bit (w

8-Bit (w

Segment

00 then DISP

0*, disp-low and disp-high are

absent

000 AX

001 CX

010 DX

011 BX

100 SP

101 BP

110 SI

111 DI

000 AL

001 CL

010 DL

011 BL

100 AH

101 CH

110 DH

111 BH

00 ES

01 CS

10 SS

11 DS

16 bits, disp-high is absent

if mod

01 then DISP

disp-low sign-extended to

(BX)

if mod

if r/m

10 then DISP

disp-high; disp-low

000 then EA

001 then EA

010 then EA

011 then EA

100 then EA

101 then EA

110 then EA

111 then EA

(SI)

(DI)

(SI)

(DI)

DISP

(BX)

(BP)

(SI)

(DI)

(BP)

(BX)

DISP

DISP*

DISP

Instructions which reference the flag register file as a 16-bit

object use the symbol FLAGS to represent the file:

DISP follows 2nd byte of instruction (before data if re-

quired)

FLAGS

X:X:X:X:(OF):(DF):(IF):(TF):(SF):(ZF):X:(AF):X:(PF):X:(CF)

*except if mod

disp-low.

00 and r/m

110 then EA

disp-high;

Mnemonics

Intel, 1978

DATA SHEET REVISION REVIEW

The following list represents key differences between this and the -004 data sheet. Please review this summa-

ry carefully.

1. The Intel 8086 implementation technology (HMOS) has been changed to (HMOS-III).

2. Delete all ‘‘changes from 1985 Handbook Specification’’ sentences.

KitchenAid KECC507GWH3 User Manual
Manhattan Computer Products 175883 User Manual
M Audio Sonica Theater User Manual
Philips 14PT1482 User Manual
Philips 15 AA 3356 User Manual
Philips 20GX8350 User Manual
Philips 21PT4455 User Manual
Philips 52PFL8605D User Manual
Philips Cordless Telephone XL395 User Manual
Philips MATCHLINE DVD 955 User Manual