USER MANUAL
ENGLISH
DEUTSCH
FRANÇAIS
NEDERLAND
POLSKI
Thank you very much for choosing the iiyama
LCD monitor.
We recommend that you take a few minutes to
read carefully through this brief but
comprehensive manual before installing and
switching on the monitor. Please keep this
manual in a safe place for your future
reference.
日本語
CE MARKING DECLARATION OF CONFORMITY
This LCD monitor complies with the requirements of the EC Directive 2004/108/EC “EMC Directive” and
2006/95/EC “Low Voltage Directive”.The electro-magnetic susceptibility has been chosen at a level that gives
correct operation in residential areas,business and light industrial premises and small-scale enterprises, inside
as well as outside of the buildings.All places of operation are characterised by their connection to the public
low voltage power supply system.
We recommend recycling of used product. Please contact your dealer or iiyama service center. Recycle
You can access the Web page of different countries from there.
We reserve the right to change specifications without notice.
All trademarks used in this user manual are the property of their respective owners.
As an ENERGY STAR® Partner, iiyama has determined that this product meets the ENERGY STAR® guidelines for energy
efficiency.
TABLE OF CONTENTS
FOR YOUR SAFETY.............................................................................. 1
SAFETY PRECAUTIONS ................................................................ 1
SPECIAL NOTES ON LCD MONITORS.......................................... 3
CUSTOMER SERVICE.................................................................... 3
CLEANING....................................................................................... 3
BEFORE YOU OPERATE THE MONITOR............................................ 4
CHECKING THE CONTENTS OF THE PACKAGE......................... 4
HOW TO USE THE STAND............................................................. 5
CONTROLS AND CONNECTORS .................................................. 6
CONNECTING YOUR MONITOR.................................................... 7
COMPUTER SETTING.................................................................... 8
ADJUSTING THE VIEWING ANGLE............................................... 8
OPERATING THE MONITOR................................................................. 9
ADJUSTMENT MENU CONTENTS.................................................10
SCREEN ADJUSTMENTS...............................................................14
POWER MANAGEMENT FEATURE ...............................................17
TROUBLE SHOOTING ..........................................................................18
APPENDIX ............................................................................................20
SPECIFICATIONS : ProLite E2607WS.............................................20
SPECIFICATIONS : ProLite E2607WSD...........................................21
SPECIFICATIONS : ProLite E2607WSV...........................................22
DIMENSIONS....................................................................................23
COMPLIANT TIMING........................................................................23
FOR YOUR SAFETY
SAFETY PRECAUTIONS
WARNING
STOP OPERATING THE MONITOR WHEN YOU SENSE TROUBLE
If you notice any abnormal phenomena such as smoke, strange sounds or fumes, unplug the monitor
and contact your dealer or iiyama service center immediately. Further use may be dangerous and can
cause fire or electric shock.
NEVER REMOVE THE CABINET
High voltage circuits are inside the monitor. Removing the cabinet may expose you to the danger of
fire or electric shock.
DO NOT PUT ANY OBJECT INTO THE MONITOR
Do not put any solid objects or liquids such as water into the monitor. In case of an accident, unplug
your monitor immediately and contact your dealer or iiyama service center. Using the monitor with any
object inside may cause fire, electric shock or damage.
INSTALL THE MONITOR ON A FLAT, STABLE SURFACE
The monitor may cause an injury if it falls or is dropped.
DO NOT USE THE MONITOR NEAR WATER
Do not use where water may be splashed or spilt onto the monitor as it may cause fire or electric
shock.
OPERATE UNDER THE SPECIFIED POWER SUPPLY
Be sure to operate the monitor only with the specified power supply. Use of an incorrect voltage will
cause malfunction and may cause fire or electric shock.
PROTECT THE CABLES
Do not pull or bend the power cable and signal cable. Do not place the monitor or any other heavy
objects on the cables. If damaged, the cables may cause fire or electric shock.
ADVERSE WEATHER CONDITIONS
It is advisable not to operate the monitor during a heavy thunder storm as the continual breaks in
power may cause malfunction. It is also advised not to touch the plug in these circumstances as it
may cause electric shock.
FOR YOUR SAFETY
1
CAUTION
INSTALLATION LOCATION
Do not install the monitor where sudden temperature changes may occur, or in humid, dusty or smoky
areas as it may cause fire, electric shock or damage. You should also avoid areas where the sun
shines directly on the monitor.
DO NOT PLACE THE MONITOR IN A HAZARDOUS POSITION
The monitor may topple and cause injury if not suitably located. Please also ensure that you do not
place any heavy objects on the monitor, and that all cables are routed such that children may not pull
the cables and possibly cause injury.
MAINTAIN GOOD VENTILATION
Ventilation slots are provided to keep the monitor from overheating. Covering the slots may cause fire.
To allow adequate air circulation, place the monitor at least 10 cm (or 4 inches) from any walls.
Do not remove the tilt stand when operating the monitor. Ventilation slots on the back of the cabinet
will be blocked and the monitor may overheat if the stand is removed. This may cause fire or damage.
Operating the monitor on its back, side, upside down or on a carpet or any other soft material may
also cause damage.
DISCONNECT THE CABLES WHEN YOU MOVE THE MONITOR
When you move the monitor, turn off the power switch, unplug the monitor and be sure the signal cable
is disconnected. If you do not disconnect them, it may cause fire or electric shock.
UNPLUG THE MONITOR
If the monitor is not in use for a long period of time it is recommended that it is left unplugged to avoid
accidents.
HOLD THE PLUG WHEN DISCONNECTING
To disconnect the power cable or signal cable, always pull it by the plug. Never pull on the cable itself
as this may cause fire or electric shock.
DO NOT TOUCH THE PLUG WITH WET HANDS
Pulling or inserting the plug with wet hands may cause electric shock.
WHEN YOU INSTALL THE MONITOR ON YOUR COMPUTER
Be sure the computer is strong enough to hold the weight of the monitor, otherwise, you may damage
your computer.
DO NOT PUT FLOPPY DISKS NEAR THE SPEAKERS
Magnetically recorded data, such as on a floppy disk, may become corrupted by the magnetic field
produced by the speakers if the disks are placed on or near the speakers.
OTHERS
ERGONOMIC RECOMMENDATIONS
To eliminate eye fatigue, do not operate the monitor against a bright background or in a dark room.
For optimal viewing comfort, the monitor should be just below eye level and 40-60 cm (16-24 inches)
away from your eyes. When using the monitor over a prolonged time, a ten minute break every hour
is recommended as looking at the screen continuously can cause eye strain.
2
FOR YOUR SAFETY
SPECIAL NOTES ON LCD MONITORS
The following symptoms are normal with LCD monitors and do not indicate a problem.
When you first turn on the LCD monitor, the picture may not fit in the display area
because of the type of computer that is used. In this case, adjust the picture position
to the correct position.
NOTE
Due to the nature of the backlight, the screen may flicker during initial use. Turn off
the Power Switch and then turn it on again to make sure the flicker disappears.
You may find slightly uneven brightness on the screen depending on the desktop
pattern you use.
Due to the nature of the LCD screen, an afterimage of the previous screen may
remain after switching the image, when the same image is displayed for hours. In
this case, the screen is recovered slowly by changing the image or turning off the
Power Switch for hours.
Contact your dealer or iiyama service center for the backlight replacement when the
screen is dark, flickering or not lighting up. Never attempt to replace it by yourself.
CUSTOMER SERVICE
NOTE
The fluorescent light used in the LCD monitor may have to be periodically replaced.
For the warranty coverage on this component, please check with local iiyama service
center.
If you have to return your unit for service and the original packaging has been discarded,
please contact your dealer or iiyama service center for advice or replacement
packaging.
CLEANING
WARNING
CAUTION
NOTE
If you drop any materials or liquids such as water into the monitor when cleaning, unplug
the power cable immediately and contact your dealer or iiyama service center.
For safety reasons, turn off the power switch and unplug the monitor before you
clean it.
To protect the LCD panel, do not scratch or rub the screen with a hard object.
Never use any of the following strong solvents. These will damage the cabinet and
the LCD screen.
Spray-type cleaner
Wax
Thinner
Benzine
Acid or Alkaline solvent
Abrasive cleaner
Touching the cabinet with any product made from rubber or plastic for a long time may
cause degeneration or loss of paint on the cabinet.
Stains can be removed with a cloth lightly moistened with a mild detergent solvent. Then
wipe the cabinet with a soft dry cloth.
CABINET
LCD
Periodic cleaning with a soft dry cloth is recommended.
SCREEN
Don't use tissue paper etc. because these will damage the LCD screen.
FOR YOUR SAFETY
3
BEFORE YOU OPERATE THE MONITOR
FEATURES
65cm (26") TFT Color LCD Monitor
Supports Resolutions up to 1920 × 1200
High Contrast 1000:1 , ACR Function Available/ High Brightness 300cd/m2 /
Quick Response Time 2ms (Gray to Gray)
Stereo Speakers
2 × 5W Stereo Speakers
HDMI interface:ProLite E2607WS
Plug & Play VESA DDC1/2B Compliant
Windows® 95/98/2000/Me/XP/Vista Compliant
Power Management (ENERGY STAR® VESA DPMS Compliant)
VESA Mounting Standard (200mm x 100mm) Compliant
CHECKING THE CONTENTS OF THE PACKAGE
The following accessories are included in your package. Check to see if they are enclosed with the
monitor. If anything is missing or damaged, please contact your local iiyama dealer or regional iiyama
office.
Power Cable*1
VGA Cable
Audio Cable
DVI-D Cable*2
User Manual
Stand
*1 The rating of the Power Cable enclosed in 120V area is 10A/125V. If you are using
a power supply higher than this rating, then a power cable with a rating of 10A/
250V must be used.However, all guarantees and warranties are void for any
problems or damage caused by a power cable not supplied by iiyama.
*2 Accessary for ProLite E2607WS
CAUTION
4
BEFORE YOU OPERATE THE MONITOR
HOW TO USE THE STAND
The monitor is shipped with the stand detached. Be sure to attach the stand before operating the
display and remove if it is necessary to re-box.
Install the Stand on a stable surface. The monitor may cause injury or damage if
it falls or is dropped.
CAUTION
Do not give a strong impact to the monitor. It may cause damage.
Unplug the monitor before installation to avoid electric shock or damage.
1. Lay the monitor flat on a table with front face down (see Fig 1). Put a piece of soft cloth on the
table beforehand to prevent the monitor from being scratched.
2. Unpack the stand and mount it onto the monitor base with aligning it to the hook (see Fig 2).
3. Slide the stand upward until it makes a click sound, indicating it is fixed (see Fig 3).
4. Stand the monitor up (see Fig 4).
(Fig 1)
(Fig 2)
(Fig 3)
(Fig 4)
BEFORE YOU OPERATE THE MONITOR
5
CONTROLS AND CONNECTORS
11
12
13
<Front>
<Back>
Menu / Input Select shortcut keys ( )*1
1
Scroll Down / Brightness/Contrast/ACR/ECO shortcut keys(
)
Scroll Up / OptiColor Mode ( )*4
Select / Input select ( 2 )
Power Indicator
Blue:
Normal operation
Orange: Power Management
The monitor enters into power management mode which reduces
NOTE
the power consumption to less than 2W when receiving no horizontal and/
or vertical sync signal.
11
Power Switch (
)
AC Connector (Power IN)
DVI-D 24Pin Connector (DVI)*5
HDMI Connector (HDMI)*2
D-SUB mini 15pin Connector (VGA)
Audio Connector (AUDIO IN)
Keyhole for Security Lock *3
Speakers
12
13
*1 Input Select shortcut keys is available under no signal input.
NOTE
*2 Available for ProLite E2607WS only.
*3 You can fasten a security lock and cable to prevent the monitor from being removed
without your permission.
*4 OptiColor Mode: Press the
Button when the Menu is not displayed.
*5 Not available for ProLite E2607WSV
6
BEFORE YOU OPERATE THE MONITOR
CONNECTING YOUR MONITOR
Ensure that both the computer and the monitor are switched off.
Connect the computer to the monitor with the signal cable.
Connect the monitor to the audio equipment with the Audio Cable for computer when using the
audio features.
Connect the Power Cable to the monitor first and then to the power supply.
The signal cables used for connecting the computer and monitor may vary with the type of
computer used. An incorrect connection may cause serious damage to both the monitor and
the computer. The cable supplied with the monitor is for a standard 15 pin D-Sub connector.
If a special cable is required please contact your local iiyama dealer or regional iiyama
office.
NOTE
For connection to Macintosh computers, contact your local iiyama dealer or regional iiyama
office for a suitable adaptor.
Make sure you tighten the finger screws at each end of the signal cable.
[Example of Connection]
Computer
NOTE
Power Cable (Accessory)
DVI-D Cable (Accessory for ProLite E2607WS and ProLite E2607WSD )
HDMI Cable (not Supplied)
D-Sub Signal Cable (Accessory)
Audio Cable (Accessory)
BEFORE YOU OPERATE THE MONITOR
7
COMPUTER SETTING
Signal Timing
Change to the desired signal timing listed on page 22: COMPLIANT TIMING.
Windows 95/98/2000/Me/XP/Vista Plug � Play
The iiyama LCD monitor complies with DDC1/2B of VESA standard. The Plug � Play function runs
on Windows 95/98/2000/Me/XP/Vista by connecting the monitor to DDC1/2B compliant computer
with the Signal Cable supplied.
For installation on Windows 95/98/2000/Me/XP/Vista: The monitor Information File for iiyama monitors
may be necessary for your computer and obtained via the Internet, using the address:
For additional information on how to download the driver for your touch screen monitor,
NOTE
please access the internet site noted above.
Monitor Drivers are not required in most cases for Windows Vista, Macintosh or Unix
operating systems. For further information, please contact your computer dealer
first for advice.
ADJUSTING THE VIEWING ANGLE
For optimal viewing it is recommended to look at the full face
of the monitor.
Hold the stand so that the monitor does not topple when you
change the monitor’s angle.
You are able to adjust the monitor’s angle up to 20 degrees
backward. (The indication of 20 degrees: tilted LCD panel holds
for a moment at this point. Tilt the panel gently; using too much
force can easily cause the tilt angle to exceed 20 degrees.)
In order to ensure a healthy and relaxed body position
when using the monitor at visual display workstations, it is
NOTE
recommended that the adjusted tilt angle should not exceed 10
degrees. Adjust the monitor’s angle to your own preference.
NOTE
Do not touch the LCD screen when you change
the angle. It may cause damage or break the LCD
screen.
NOTE
Careful attention is required not to catch your fingers
or hands when you change the angle.
Do not tilt the post beyond 20 degrees except when
repacking the monitor in its box.
To do so may cause the monitor to fall over and
break.
8
BEFORE YOU OPERATE THE MONITOR
OPERATING THE MONITOR
To create the best picture, your iiyama LCD monitor has been preset at the factory with the COMPLIANT
TIMING shown on page 21. You are also able to adjust the picture by following the button operation
shown below. For more detailed adjustments, see page 14 for SCREEN ADJUSTMENTS.
Press the Menu Button to start the On Screen Display feature. There are additional
Menu items which can be switched by using the / Buttons.
Main Menu
Auto Image Adjust
Contrast/Brightness
Input Select
Audio Adjust
Color Adjust
Information
Manual Image Adjust
Setup Menu
Memory Recall
1 : Exit
2 : Select
Select the Menu item which contains the adjustment icon relating to the adjustment
you want to make. Press the Select Button. Then, use the / Buttons to highlight
the desired adjustment icon.
Press the Select Button again. Use the / Buttons to make the appropriate
adjustment or setting.
For example, to correct for vertical position, select Menu item of Image Adjust and then press the
Select Button. Then, select
(H. / V.Position) by using the / Buttons.
Manual Image Adjust
Main Menu
Auto Image Adjust
Horizontal Size
H./V. Position
Fine Tune
Contrast/Brightness
Input Select
Audio Adjust
Sharpness
Color Adjust
Video Mode Adjustment
OptiColor Mode
Information
Manual Image Adjust
Setup Menu
Memory Recall
1
: Exit
2
: Select
1
: Exit
2
: Select
An adjustment page appears after you press the Select Button. Press the Select Button again.
Then, use the / Buttons to change the vertical position settings. The vertical position of the
overall display should be changing accordingly while you are doing this.
NOTE
When button operations are aborted during adjustment, On-Screen Display disappears when the
time set for the OSD Time Out has passed. Also, press the Menu button to quickly turn off the On-
Screen Display.
Any changes are automatically saved in the memory when the On Screen Display disappears.
Turning off the power should be avoided while using the Menu.
ADJUSTING
Adjustments for H. / V. Position, H.Size and Fine Tune are saved for each signal timing. Except for
these adjustments, all other adjustments have only one setting which applies to all signal timings.
OPERATING THE MONITOR
9
ADJUSTMENT MENU CONTENTS
Auto Image Adjust
Adjustment Item
Problem / Option
Button to Press
Auto Image Adjust *
Only Analog input
Adjust H. / V. Position, H.Size and Fine Tune
automatically.
The screen becomes dark for approximately five seconds during the adjustment.
NOTE
*
For best results, use the Auto Adjust in conjunction with the adjustment pattern. See page 14 for
SCREEN ADJUSTMENTS.
Contrast/Brightness
Adjustment Item
Contrast*3
Problem / Option
Too dull
Button to Press
Too intense
Too dark
Brightness *1,3
Too bright
On
Off
Increased contrast ratio
typical contrast ratio
ACR*2
On
Off
Brightness of back light is reduced.
Normal
ECO
*1 Adjust the Brightness when you are using the monitor in a dark room and feel the screen is too
bright. Can not select when ACR is On.
*2 ACR can not enable the same time when ECO is on.
*3 Contrast and Brightness adjustment disabled when ECO is active or when Opticolor Mode is set
to Text or Cinema or Game or Scenery.
NOTE
Contrast, Brightness,ACR and ECO are switched as follows by pressing the /Button
successively.
Contrast
Brightness
ACR
ECO
You can skip the Menu items and display an adjustment scale directly by using the following button
operations.
Contrast/Brightness/ ACR/ ECO :Press the Button when the Menu is not displayed.
10
OPERATING THE MONITOR
Input Select*
Input Select
Adjustment Item
Problem / Option
Button to Press
Analog
Select the Analog input
Select the HDMI input
Select the DVI input
Input Select
HDMI
DVI
Analog,HDMI and DVI are switched as follows by pressing the Button successively.
2
Analog
HDMI
DVI
You can display the Input Select Menu by pressing the button under no signal input.
1
*Not available for ProLite E2607WSV .
Audio Adjust
Adjustment Item
Problem / Option
Button to Press
Too soft
Too loud
Volume
Mute
Return the sound volume to the previous level.
Turn off the sound temporarily.
Mute off and on are switched as follows by pressing the Select Button successively.
NOTE
Mute off
Mute on
Color Adjust
Adjustment Item
Problem / Option
Button to Press
Cool
Bluish white (9300K)
Reddish white (6500K)
Greenish white (5400K)
Red
Normal
Warm
Too weak
User Color
2
Green
Blue
Too strong
Information
Information
H. Frequency:
Displays information regarding the current input signal coming
from the graphic card in your computer.
75.0 KHz
V. Frequency:
Resolution:
60.0 Hz
1920 x 1200
154 MHz
NOTE
Pixel Clock:
Serial Number:
Model Number:
0598781300001
PLE2607WS
See your graphic card user guide for more information about
changing the resolution and refresh
1 : Exit
OPERATING THE MONITOR 11
Manual Image Adjust
Adjustment Item
Problem / Option
Button to Press
Too narrow
Too wide
Horizontal Size
Only Analog Input
Too far to the left
Too far to the right
H. Position
V. Position
H./V. Position
Only Analog Input
Too low
Too high
To correct flickering text or lines
Fine Tune
Sharpness
Only Analog Input
Adjust the picture quality at resolutions of
less 1920 x 1200.
You can change the picture quality (4 steps).
Full Screen
Select full screen
Over Screen
Select over screen
Select Aspect ratio
Video Mode Adjustment
Aspect Ratio 4:3*1
Standard
Office
For general windows environment
and monitor default setting
For text editing and viewing in a
word processing environment
OptiColor Mode
Movie
For movie and video environment
For PC game environment
Game
Picture
For displaying outdoor scenery
images
H. Position and V. Position are switched as follows by pressing the/Button
NOTE
successively.
H. Position
V. Position
*1 It can display in the center of the screen with a 4:3 or 5:4 aspect ratio when input video
resolution is 4:3 or 5:4.
Standard, Office,Movie, Game and Picture are switched as follows by pressing the / Button
successively.
Standard Office
Movie
Game
Picture
12
OPERATING THE MONITOR
Setup Menu
Adjustment Item
Problem / Option
Button to Press
Finnish
English
Français
Deutsch
Espanol
Italiano
English
French
German
Spanish
Italian
Suomi
Japanese
Simplified Chinese
Traditional Chinese
日本語
简体中文
Language Select
繁体中文
OSD is too far to the left
OSD is too far to the right
H.Position
V.Position
OSD Position
OSD Time Out
OSD is too low
OSD is too high
You can set the OSD display duration time between 5
and 60 seconds.
Memory Recall
Adjustment Item
Memory Recall
Problem / Option
Button to Press
Factory-preset data is restored.
OPERATING THE MONITOR
13
SCREEN ADJUSTMENTS
Adjust the image by following the procedure below to get the desired picture when selecting Analog input.
The screen adjustments described in this manual are designed to set image position and minimize
flicker or blur for the particular computer in use.
The monitor is designed to provide the best performance at resolution of 1920 × 1200, but can not
provide the best at resolutions of less than 1920 × 1200 becausethepictureisautomatically stretched
to fit the full screen. It is recommended to operate at resolution of 1920 × 1200 in normal use.
Displayed text or lines will be blurred or irregular in thickness when the picture is stretched due to
the screen enlargement process.
It is preferable to adjust the image position and frequency with the monitor controls, rather than the
computer software or utilities.
Perform adjustments after a warm-up period of at least thirty minutes.
Additional adjustments may be required after the Auto Adjust depending on the resolution or signal
timing.
TheAutoAdjust may not work correctly when displaying the picture other than the screen adjustment
pattern. In this case, manual adjustments are required.
There are two ways to adjust the screen. One way is automatic adjustment for Position, H.Size and
Fine Tune. The other way is performing each adjustment manually.
Perform theAutoAdjust first when the monitor is connected to a new computer, or resolution is changed.
If the screen has a flicker or blur, or the picture does not fit in the display area after performing the
Auto Adjust, manual adjustments are required. Both adjustments should be made by using the screen
adjustment pattern (Test.bmp) obtained via the IIYAMA web site (http://www.iiyama.com).
Adjust the image by following the procedure below to get the desired picture.
This manual explains adjustment under Windows 95/98/2000/Me/XP/Vista.
Display the picture at the optimum resolution.
Enter the Test.bmp (screen adjustment pattern) to wallpaper.
Consult the appropriate documentation for doing this.
NOTE
Test.bmp is made at resolution of 1280 × 1024 Set the display position to center in the
wallpaper setting dialogue box. If you use Microsoft® PLUS! 95/98 cancel the setting
of “Stretch desktop wallpaper to fit the screen”.
[Adjustment pattern]
Color bar
Zebra pattern
Picture frame
14
OPERATING THE MONITOR
Press the Auto Button. (Auto Adjust)
Adjust the image manually by following procedure below when the screen has a flicker or
blur, or the picture does not fit in the display area after performing the Auto Adjust.
Adjust the V.Position so that the top and bottom of the picture frame will fit to the display
area.
1) Adjust the H.Position so that the left side of the picture frame will move to the left edge
of the display area.
2) Stretch the right side of the picture frame to the right edge of the display area by adjusting
the H.Size.
When the left side of the picture frame moves apart from the left edge of the display
NOTE
area during the H.Size adjustment, adjust steps 1) and 2).
Another way to make the H.Size adjustment is to correct the vertical wavy lines in the
zebra pattern.
The picture may flicker during the H.Size, H.Position and V.Position adjustment.
In case the picture frame is bigger or smaller than the data display area after the H.Size
adjustment, repeat steps from .
OPERATING THE MONITOR
15
1
Adjust the Fine Tune to correct horizontal wavy noise, flicker or blur in the zebra pattern.
In case the strong flicker or blurs remain on a part of the screen, repeat steps and
NOTE
because the H.Size may not be adjusted correctly. If the flicker or blurs still remain,
set the refresh rate of computer to low (60Hz) and repeat steps from again.
Adjust the H.Position after the Fine Tune adjustment if the horizontal position moves
during the adjustment.
Adjust the Brightness and Color Adjust to get the desired picture after you complete the
H.Size and Fine Tune adjustments.
Put back your favorite wallpaper.
16
OPERATING THE MONITOR
POWER MANAGEMENT FEATURE
The power management feature of this product complies with power saving requirement of ENERGY
STAR® and VESA DPMS. When activated, it automatically reduces unnecessary power consumption
of the monitor when your computer is not in use.
To use the feature, the monitor needs to be connected to a VESA DPMS compliant computer. There
is a power management step the monitor takes as described below. The power management function,
including any timer settings is configured by the operating system. Check your operating system manual
for information on how this can be configured.
Power Management Mode
When the H-sync signal / V-sync signal / H and V sync signals from the computer are off, the monitor
enters into Power Management Mode which reduces the power consumption to less than 2W. The
screen becomes dark, and the power indicator turns to orange. From Power Management Mode, the
image reappears in several seconds when either the keyboard or the mouse are touched again.
Power Indicator
Blue
Orange
0
2W
100%
Even when using the power management mode, the monitor consumes electricity. Turn
off the Power Switch whenever the monitor is not in use, during the night and weekends,
to avoid unnecessary power consumption.
NOTE
It is possible that the video signal from the computer may be on while the H or V sync
signal is missing. In this instance, the POWER MANAGEMENT feature may not work
properly.
OPERATING THE MONITOR
17
TROUBLE SHOOTING
If the monitor fails to operate correctly, please follow the steps below for a possible solution.
1. Perform the adjustments described in OPERATING THE MONITOR, depending on the problem
you have. If the monitor does not get a picture, skip to 2.
2. Consult the following items if you cannot find an appropriate adjustment item in OPERATING THE
MONITOR or if the problem persists.
3.
If you are experiencing a problem which is not described below or you cannot correct the
problem, discontinue using the monitor and contact your dealer or iiyama service center for further
assistance.
Problem
Check
The picture does
not appear.
(Power indicator
does not light up.)
The Power Cable is firmly seated in the socket.
The Power Switch is turned ON.
The AC socket is live. Please check with another piece of equipment.
(Power indicator
is blue.)
If the blank screen saver is in active mode, touch the keyboard or the
mouse.
Increase the Contrast and/or Brightness.
The computer is ON.
The Signal Cable is properly connected.
The signal timing of the computer is within the specification of the monitor.
(Power indicator
is orange.)
If the monitor is in power management mode, touch the keyboard or the
mouse.
The computer is ON.
The Signal Cable is properly connected.
The signal timing of the computer is within the specification of the monitor.
The screen is not
synchronized.
The Signal Cable is properly connected.
The signal timing of the computer is within the specification of the monitor.
The video output level of the computer is within the specification of the
monitor.
The screen
position is not in
the center.
The signal timing of the computer is within the specification of the monitor.
The screen is
too bright or too
dark.
The video output level of the computer is within the specification of the
monitor.
The screen is
The power voltage is within the specification of the monitor.
The signal timing of the computer is within the specification of the monitor.
shaking.
18
TROUBLE SHOOTING
Problem
No sound.
Check
The audio equipment (computer etc.) is ON.
The Audio Cable is properly connected.
The Volume is turned up.
The Mute is OFF.
The audio output level of the audio equipment is within the specification
of the monitor.
The sound is too
loud or too quiet.
The audio output level of the audio equipment is within the specification of
the monitor.
A strange noise is
heard.
The Audio Cable is properly connected.
RECYCLING INFORMATION
For better environment protection please don’t dispose your monitor.
TROUBLESHOOTING
19
APPENDIX
SPECIFICATIONS:ProLite E2607WS
Size
Pixel pitch
Diagonal: 65cm / 26"
0.2865 mm H × 0.2865mm V
LCD Panel
Brightness
300cd/m2 (Typical)
Contrast ratio
1000 : 1 (Typical), ACR function available
Viewable angle Right / Left : 85 degrees each, Up:80 degrees, Down: 70 degrees (Typical)
Response time
2ms (Gray to Gray)
Display Colors
Approx.16.7M
Sync Frequency
Maximum Resolution
Input Connector
Plug � Play
Horizontal: 31.0-80.0kHz, Vertical: 56-75Hz
1920 × 1200
D-Sub mini 15 pin,DVI-24 pin,HDMI
VESA DDC1/2BTM
Input Sync Signal
Input Video Signal
Separate sync: TTL, Positive or Negative
Analog: 0.7Vp-p (Standard), 75Ω, Positive
Digital (DVI): Digital Visual Interface standard Rev. 1.0 compliance
Digital (HDMI): HDMI (1.2)
Input Audio Connector
Input Audio Signal
Speakers
ø 3.5mm mini jack (Stereo)
1Vrms maximum
5W × 2 (Stereo speakers)
Maximum Screen Size
Power Source
550.1mm W × 343.8mm H / 21.66" W × 13.54" H
100-240VAC, 50/60Hz, 2.0A
Power Consumption
Dimensions / Net Weight
52W (Typ), Power management mode: 2W maximum*
597.5 × 460.5 × 238.0 mm / 23.5 ×18.1 × 9.4 (W×H×D),
8.3kg / 18.3lbs
Tilt Angle
20 degrees (Up: 0-20 degrees)
Operating: Temperature
Humidity
5 to 35°C / 41 to 95°F
10 to 80% (No condensation)
Environmental
Considerations
Storage: Temperature -20 to 60°C / -4 to 140°F
Humidity
10 to 70% (No condensation)
CE,TUV/Baurt,Energy star,PSE
Approvals
* Condition: Audio equipment is not connected.
20
APPENDIX
APPENDIX
SPECIFICATIONS:ProLite E2607WSD
Size
Pixel pitch
Diagonal: 65cm / 26"
0.2865 mm H × 0.2865mm V
LCD Panel
Brightness
300cd/m2 (Typical)
Contrast ratio
1000 : 1 (Typical), ACR function available
Viewable angle Right / Left : 85 degrees each, Up:80 degrees, Down: 70 degrees (Typical)
Response time
2ms (Gray to Gray)
Display Colors
Approx.16.7M
Sync Frequency
Maximum Resolution
Input Connector
Plug � Play
Horizontal: 31.0-80.0kHz, Vertical: 56-75Hz
1920 × 1200
D-Sub mini 15 pin,DVI-24 pin
VESA DDC1/2BTM
Input Sync Signal
Input Video Signal
Separate sync: TTL, Positive or Negative
Analog: 0.7Vp-p (Standard), 75Ω, Positive
Digital (DVI): Digital Visual Interface standard Rev. 1.0 compliance
Input Audio Connector
Input Audio Signal
Speakers
ø 3.5mm mini jack (Stereo)
1Vrms maximum
5W × 2 (Stereo speakers)
Maximum Screen Size
Power Source
550.1mm W × 343.8mm H / 21.66" W × 13.54" H
100-240VAC, 50/60Hz, 2.0A
Power Consumption
Dimensions / Net Weight
52W (Typ), Power management mode: 2W maximum*
597.5 × 460.5 × 238.0 mm / 23.5 ×18.1 × 9.4 (W×H×D),
8.3kg / 18.3lbs
Tilt Angle
20 degrees (Up: 0-20 degrees)
Operating: Temperature
Humidity
5 to 35°C / 41 to 95°F
10 to 80% (No condensation)
Environmental
Considerations
Storage: Temperature -20 to 60°C / -4 to 140°F
Humidity
10 to 70% (No condensation)
Approvals
CE,TUV/Baurt,Energy star
* Condition: Audio equipment is not connected.
APPENDIX
21
APPENDIX
SPECIFICATIONS:ProLite E2607WSV
Size
Diagonal: 65cm / 26"
LCD Panel
Pixel pitch
Brightness
Contrast ratio
Viewable angle
0.2865 mm H × 0.2865mm V
300cd/m2 (Typical)
1000 : 1 (Typical), ACR function available
Right / Left : 85 degrees each, Up:80 degrees, Down: 70 degrees (Typical)
Response time 2ms (Gray to Gray)
Display Colors
Approx.16.7M
Sync Frequency
Maximum Resolution
Input Connector
Plug � Play
Horizontal: 31.0-80.0kHz, Vertical: 56-75Hz
1920 × 1200
D-Sub mini 15 pin,
VESA DDC1/2BTM
Input Sync Signal
Input Video Signal
Input Audio Connector
Separate sync: TTL, Positive or Negative
Analog: 0.7Vp-p (Standard), 75Ω, Positive
ø 3.5mm mini jack (Stereo)
Input Audio Signal
Speakers
1Vrms maximum
5W × 2 (Stereo speakers)
Maximum Screen Size
550.1mm W × 343.8mm H / 21.66" W × 13.54" H
Power Source
100-240VAC, 50/60Hz, 2.0A
Power Consumption
Dimensions / Net Weight
52W (Typ), Power management mode: 2W maximum*
597.5 × 460.5 × 238.0 mm / 23.5 ×18.1 × 9.4 (W×H×D),
8.3kg / 18.3lbs
Tilt Angle
20 degrees (Up: 0-20 degrees)
Operating: Temperature
Humidity
5 to 35°C / 41 to 95°F
10 to 80% (No condensation)
Environmental
Considerations
Storage: Temperature -20 to 60°C / -4 to 140°F
10 to 70% (No condensation)
CE,TUV/Baurt,Energy star,VCCI-B
Humidity
Approvals
NOTE * Condition: Audio equipment is not connected.
22
APPENDIX
DIMENSIONS
DIMENSIONS
PC Input
COMPLIANT TIMING
Vertical
Frequency
Video Mode
Horizontal
Frequency
Dot Clock
59.940Hz
75.000Hz
60.317Hz
72.188Hz
75.000Hz
60.004Hz
70.069Hz
75.029Hz
60.020Hz
75.025Hz
59.887Hz
74.984Hz
60.000Hz
60.000Hz
59.950Hz
70.087Hz
31.469kHz
37.500kHz
37.879kHz
48.077kHz
46.875kHz
48.363kHz
56.476kHz
60.023kHz
63.981kHz
79.976kHz
55.935kHz
70.635kHz
75.000kHz
65.290kHz
74.038kHz
31.469kHz
25.175MHz
31.500MHz
40.000MHz
50.000MHz
49.500MHz
65.000MHz
75.000MHz
78.750MHz
108.000MHz
135.000MHz
106.500MHz
136.750MHz
162.000MHz
146.250MHz
154.000MHz
28.322MHz*
640 × 480
VGA
SVGA 800 × 600
VESA
XGA
1024 × 768
SXGA 1280 × 1024
1440 ×900
WXGA+
1600 ×1200
1680 ×1050
1920 ×1200
720 × 400
UXGA
WSXGA+
WUXGA
VGA TEXT
NOTE
* DVI, HDMI Input is not compliant.
Video input 480P/720P/1080i/1080P
APPENDIX
23
|