Color Monitor
T541A
English
User's Guide
Contents
Safety(Read first) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Setting up the monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Handling Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Workplace Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Adjusting the Monitor Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Working Practices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Connecting your Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Switching on your Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Device driver Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Windows XP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Windows Millennium . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Windows 2000
Windows 98
Windows 95
8
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Auto Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Auto Setup for DOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Auto Setup for Windows 3.1, Windows 95, Windows 98, Windows 2000,
Windows NT, Windows Me or Windows XP. . . . . . . . . . . . . . . . . . . . 12
Adjusting Your LCD Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
User controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
On-screen display (OSD) controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Further Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Display modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Product Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Further Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Service Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Notices and trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
1
Ennen kuin asennat tämän tuotteen, lue turvaohjeet kohdasta Safety Information.
Pred instalací tohoto produktu si prectete prírucku bezpecnostních instrukcí.
2
Setting up the monitor
Product Description
The IBM T541A Color Monitor works with a computer with a suitable on-
board sub-system or Video Card that supports XGA1024 x 768, SVGA 800 x
600, or VGA 604 x 408 resolutions at 60Hz.
In addition to your monitor, your option package includes the following:
• User’s Guide and Installation Files CD
• Monitor Warranty and Safety manual
• T541A Color Monitor Quick Start Guide
• Power Cord
• T541A Color Monitor
Handling Instructions
Do not support the monitor
within the screen area. The
Liquid Crystal Display is
glass and can be damaged
by rough handling or
1. Lift the monitor by placing your hands where indicated below.
excessive pressure.
2. Before using your monitor for the first time, remove the clear protective
film from the front of the screen.
3
Workplace Preparation
This section gives advice
Height
on what you should
consider before you set up your
monitor.
Position the monitor so that the top of the screen is slightly below your eye
level when you sit at your workstation.
Orientation
Choose a position that gives the least reflection from lights and windows,
usually at a right angle to any windows. Position the monitor directly in front of
you so that you do not have to twist your body to use it. Tilt the monitor to a
comfortable viewing angle.
Adjusting the Monitor Position
Viewing Angle
You can tilt the screen backward and forward as shown below.
Working Practices
This section gives
advice on how you can
work comfortably and reduce
fatigue.
Rest
Take regular breaks. Vary your posture, stand up and stretch occasionally as
prolonged use of computer workstations can be tiring.
4
Back
Sit back in your chair and use the backrest.
Hands
Adjust the seat height so that your forearms are approximately horizontal and
your wrists are straight when using the keyboard. Your upper arms should be
relaxed with your elbows near your body.
Use a light touch on the keyboard, keeping your hands and fingers relaxed.
Allow a space in front of the keyboard to rest your wrists when not typing.
Consider using a wristpad.
Eyesight
Working with monitors, in common with any prolonged close work, can be
visually demanding. Look away from the screen periodically and have your
eyesight checked regularly.
Screen settings
Set the screen brightness and contrast to a comfortable level. You may have
to adjust this as the lighting changes during the day. Many application
programs let you select color combinations which can help you to view in
comfort. See the User controls section (page 10) for more information.
5
Connecting your Monitor
Be sure to read the Monitor
Safety and Warranty manual
that comes with your monitor
before carrying out this
procedure.
1. Turn off your computer and all attached devices.
2. Connect the signal cable to the video port on the back of your computer.
This port might be directly attached to your computer (figure A), or it
might be part of a video adapter card (figure B). The video port on your
computer or video adapter card may be colored blue to match the blue
connector on your monitor’s video cable.
The ac adapter and signal
cable are connected to
your monitor. If you wish to
change these or to fit a different
stand, see the Further help
section (page 19).
3. Connect the power cord to the power adapter and then plug the power
cord into a properly grounded outlet.
Switching on your Monitor
1. Switch on the power source and your computer.
2. Switch on your monitor by pushing and releasing the power switch
marked
.
To switch off your monitor, push and release the power switch again.
3. Turn on the monitor and then the computer.
6
Device driver installation
Use the User’s Guide and Installation Files CD that comes with your monitor
to install the appropriate device driver for your operating system.
Installing the Windows XP device driver
®
®
To manually install or update the device driver for the Microsoft Windows
XP operating system, perform the following steps:
1. Insert the User’s Guide and Installation Files CD into the computer CD-
ROM drive.
2. Click Start ꢀ Control Panel ꢀAppearance & Themes and then click
the Display icon.
3. In the Display Properties window, click the Settings tab, and then click
Advanced.
4. Click the Monitor tab, and then click Properties ꢀDriver tab ꢀUpdate
Driver.
5. When the Hardware Update Wizard window opens, select “Install the soft-
ware automatically,” click Next> and then Finish to complete the
installation.
6. Close the Display Properties window.
7. Remove the User’s Guide and Installation Files CD from the computer
CD-ROM drive.
Installing the Windows Me device driver
To manually install or update the device driver for the Microsoft Windows Mil-
lennium Eidtion operating system, perform the following steps:
1. Click Start ꢀ Settings ꢀ Control Panel and then double-click Display.
2. In the Display Properties window, click the Settings tab, and then click
Advanced.
3. Click the Monitor tab, and then click Change ꢀ Specify the location of
the driver ꢀ Next.
4. When the Update Device Driver Wizard window opens, select "Display a
list of all the drivers in a specific location, so you can select the driver you
want," and click Next>.
5. Insert the the User’s Guide and Installation Files CD into the computer
CD-ROM drive, then click Have Disk.
6. Type d:\ (change the drive letter to match your CD-ROM drive if it is not
drive D) in the Copy manufacturer's files from: box, then click OK.
7. Click Next>, Next>, and then Finish to complete the installation.
8. Close the Display Properties window.
9. Remove the User’s Guide and Installation Files CD from the computer
CD-ROM drive.
7
Installing the Windows 2000 device driver
To manually install or update the device driver for the Microsoft Windows 2000
Professional operating system, perform the following steps:
1. Click Start ꢀ Settings ꢀ Control Panel and then double-click Display.
2. In the Display Properties window, click the Settings tab, and then click
Advanced.
3. Click the Monitor tab, and then click Properties ꢀ Driver ꢀUpdate
Driver.
4. When the Update Device Driver Wizard window opens, select "Search for
a suitable driver for my device," and click Next>.
5. Insert the User’s Guide and Installation Files CD into the computer CD-
ROM drive, type d:\ (change the drive letter to match your CD-ROM drive
if it is not drive D) in the Copy manufacturer's files from: box, click
Next> and then Finish to complete the installation.
6. Close the Display Properties window.
7. Remove the User’s Guide and Installation Files CD from the computer
CD-ROM drive.
Installing the Windows 98 device driver
Windows 98 automatically detects the new monitor and displays the Add New
Hardware Wizard window if the device driver is not already installed.
1. Insert the Device Driver and User’s Guide CD into the computer CD-ROM
drive, and click Next> twice when the Add New Hardware Wizard window
opens.
2. Click the CD-ROM drive box to install the device drivers from the CD and
then click Next>.
3. Confirm that the device driver was found on the CD, and click Next> twice
to install the device driver.
4. Click Finish to exit the Add New Hardware Wizard window.
To manually install or update the device driver for the Microsoft Windows 98
operating system, perform the following steps:
1. Click Start ꢀ Settings ꢀ Control Panel and then double-click Display.
2. In the Display Properties window, click the Settings tab, and then click
Advanced.
3. Click the Monitor tab, and then click Change.
4. When the Update Device Driver Wizard window opens, follow the steps in
the previous paragraph.
5. Remove the User’s Guide and Installation Files CD from the computer
CD-ROM drive.
8
Installing the Windows 95 device driver
Right-click the My Computer icon on the computer desktop and then select Prop-
erties -> System to view the version number listed in the System window. Perform
the steps below for the appropriate version.
If you have Windows 95 Version 4.00.950A, use the following steps to manually
install or update the device driver:
1. Click Start ꢀ Settings ꢀ Control Panel and then double-click Display.
2. In the Display Properties window, click the Settings tab and then click
Change Display Type.
3. In the Change Display Type window, click Change and then click Have
Disk.
4. Insert the User’s Guide and Installation Files CD into the computer CD-
ROM drive, type d:\ (change the drive letter to match your CD-ROM drive
if it is not drive D) in the Copy manufacturer's files from: box, and click
OK.
5. In the Select Device window, click the appropriate monitor model and then
click OK.
6. In the Change Display Type window, click Close.
7. In the Display Properties window, click OK.
8. Remove the User’s Guide and Installation Files CD from the computer
CD-ROM drive.
If you have Windows 95 Version 4.00.950B, use the following steps to manually
install or update the device driver:
1. Click Start ꢀ Settings ꢀ Control Panel and then double-click Display.
2. In the Display Properties window, click the Settings tab and then click
Advanced Properties.
3. In the Advanced Display Properties window, click the Monitor tab and
then click Change.
4. In the Select Device window, click Have Disk.
5. Insert the User’s Guide and Installation Files CD into the computer CD-
ROM drive, type d:\ (change the drive letter to match your CD-ROM drive
if it is not drive D) in the Copy manufacturer's files from: box, and click
OK.
6. In the Select Device window, click the appropriate monitor model and then
click OK.
7. In the Advanced Display Properties window, click Close.
8. In the Display Properties window, click OK.
9. Remove the User’s Guide and Installation Files CD from the computer
CD-ROM drive.
9
Auto Setup
Auto Setup
The Setup Utility
included on the setup
diskette is for displaying do
patterns. They do not replace
or modify the display dirver.
When you first use your monitor you must perform Auto Setup. This
procedure sets up your monitor to process the video signals from your
computer without image discoloration or smearing. After you perform Auto
Setup, the settings are stored and used each time you turn on the monitor.
In order to optimise the displayed image a set-up utility is provided on the CD.
Operation of the utility is dependent on the operating system on your PC. For
correct operation locate the operating system on your PC from the table
below and follow the appropriate instructions. You may choose to run AUTO
SETUP for each operating system that you use. This means that if you
sometimes use your monitor while running any version of Windows and
sometimes also use it from within DOS (not a DOS window), you must run
AUTO SETUP for both Windows and DOS. You may run versions of AUTO SETUP
in any order.
The Auto Setup instructions
require the monitor to be
warmed up for 15 minutes.
This is not required for normal
operation.
By pressing the
ꢁ
and ꢀkeys
simultaneously allows direct
access to the auto set-up
controls.
Operating System
DOS
Corresponding Auto Setup procedure
Auto Setup for DOS
Windows 3.1, Windows 95,
Windows 98, Windows
2000, Windows NT,
Windows Me or Windows
XP
Auto Setup for Windows 3.1, Windows 95,
Windows 98, Windows 2000, Windows
NT, Windows Me or Windows XP
Before you begin AUTO SETUP for your PC:
1. Make sure the PC’s video mode is set in the range of the supported
screen resolution shown in the table.
The AUTO SETUP process only
applies to the current screen
mode. When a new mode is
selected, repeat this section to
reset the monitor
You should perform AUTO SETUP for each screen mode you use.
10
Auto Setup for DOS
If the monitor is in standby
mode (STANDBY ON), it
1. Turn on the monitor first; then the PC.
may automatically turn off while
you are waiting for it to warm up.
If this happens, switch off the
monitor and switch it on again
after a few seconds.
If the message CHECK SIGNAL CABLE is displayed, or if nothing is
displayed check:
•
•
•
that the video interface cable is connected properly.
the correct video adapter card is installed.
the correct supported display mode is selected for your PC.
If you are using PC-DOS/
V, change to U.S. mode by
typing ‘CHEV US’ and pressing
ENTER at the command
prompt.
2. Wait approximately 15 minutes, until the monitor warms up.
3. Insert the User’s Guide and Installation Files CD into the computer CD-
ROM drive.
You must use DOS when
you run DOS Auto Setup.
4. Display the command prompt screen of the DOS full-screen display.
5. Type d:\ (change the drive letter to match your CD-ROM drive if it is not
drive D).
6. Type ‘TESTPAT’ and press ENTER.
7. Select from the screen the number for the color or text mode you want to
setup.
8. Select from the screen the number for the video mode you want to
setup.
You may repeat this process for as many of the color and video modes
as you need.
The size and diversity of
the dot pattern varies with
the screen resolution.
9. When the dot pattern appears, press the OSD Enter button
bottom of the monitor to display the initial OSD menu.
at the
10. Use an Arrow button (
then press the OSD Enter
or
) to select the IMAGE LOCK icon
button to access the function.
11. Using an Arrow button (
or
), select AUTOMATIC and press the
OSD Enter button
. This activates the AUTO SETUP procedure, which
will optimize the display settings with the provided dot-patterns.
The screen will blink off several times and you may notice small
changes to the test pattern.
12. When finished, the OSD main menu returns. Press the Exit button
to exit from the OSD.
13. Press the ESCAPE key to exit the test pattern program.
14. Type ‘Exit’ at the command prompt to return to Windows.
If you use other operating systems, perform the appropriate AUTO SETUP for
those systems, also: see
Auto Setup for Windows 3.1, Windows 95, Windows 98, Windows NT or
Windows 2000, Windows Me or Windows XP.
11
Auto Setup for Windows 3.1, Windows 95, Windows 98, Windows NT
or Windows 2000, Windows Me or Windows XP
If the monitor is in standby
mode (STANDBY ON), it
1. Turn on the monitor first; then the PC.
may automatically turn off while
you are waiting for it to warm up.
If the message CHECK SIGNAL CABLE is displayed, or if nothing is
displayed check:
•
•
•
that the video interface cable is connected properly.
the correct video adapter card is installed.
the correct supported display mode is selected for your PC.
2. Wait approximately 15 minutes, until the monitor warms up.
3. Drag the icon bar and tool bar, if they are displayed, to the bottom of the
screen.
4. Insert the User’s Guide and Installation Files CD into the computer CD-
ROM drive.
The size and diversity of
the dot pattern varies with
the screen resolution.
5. Check the operating system installed on your PC and follow the
instructions from the table below.
Operating
System
Step1
Step2
Step3
Step4
Windows 3.1
Open
PROGRAM
MANGER
Type
Select
FILE
Select
RUN
‘d:\TESTPAT’
(change the
drive letter to
match your
CD-ROM
drive if it is
not drive D)
and press
Windows NT 3.5
Windows 95,
Windows 98,
Windows 2000,
Windows NT,
Windows Me or
Windows XP
Select
START
Select RUN
ENTER
6. When the test pattern appears, press the OSD Enter button
bottom of the monitor to display the initial OSD menu.
at the
Position the mouse pointer
at the bottom center of the
screen. This allows AUTO
SETUP to run properly
7. Use an Arrow button (
and press the OSD Enter button
8. Using an Arrow button ( or
OSD Enter button
or
) to select the IMAGE LOCK icon
to access the function.
), select AUTOMATIC and press the
. This activates the AUTO SETUP procedure, which
will optimize the display settings with the provided test pattern.
The screen will dim, blink on and off several times, and you may notice
small changes to the test pattern.
To abort the AUTO SETUP function, press the ESC key.
12
9. When finished, the OSD main menu returns. Press the Exit button
once to exit from the OSD.
10. Press the ESC key to return to Windows.
You have completed the monitor setup for Windows. If you use other operat-
ing systems, perform the appropriate AUTO SETUP for those systems, also: see
Auto Setup for DOS.
13
Adjusting Your LCD Monitor
User controls
User control features
Icon
Control
Exit
Description
Displays the OSD main menu
Exits from menus and sub-menus
Exits the OSD
Displays the OSD main menu
Moves the cursor to highlight icons and other
options
Left Arrow
Displays the OSD main menu
Moves the cursor to highlight icons and other
options
Right Arrow
Displays the OSD main menu
Enters menus and sub-menus and selects the
highlighted option
OSD Enter
Power Switch
Switches the monitor on and off
Operation
The image is already
optimized for many display
modes; however, the user
controls can be used to adjust
the image to your liking.
•
•
Press any of the OSD control buttons to display the main OSD menu.
Use the Arrow buttons to move among the icons. Select an icon and press
OSD Enter to access that function. If there is a sub-menu, you can move
between options using the Arrow buttons, then press OSD Enter to select
that function. Use the Arrow buttons to make adjustments.
14
The settings are saved
after adjustment and when
exiting the OSD and will be
effective thereafter.
•
Press the Exit button to move backwards through the sub-menus and exit
from the OSD.
Note: After making adjustments, the Power indicator LED will briefly turn
amber to indicate that the new value has been saved.
OSD Lock / Unlock
This feature allows you to secure the current control settings, while allowing
the user to adjust Brightness and Contrast, so that they cannot be
inadvertently changed. You can unlock the OSD controls at any time by using
the same procedure.
Push and hold the OSD Enter button for 10 seconds to Lock or to Unlock.
When locked, a “LOCKED” message will be displayed.
15
On-screen display (OSD) controls
The settings adjustable with the user controls are viewed through the On-
Screen Display (OSD). Press any of the OSD buttons to activate the OSD.
The LCD monitor needs
time to become thermally
Initial appearance of OSD
stable the first time you turn it on
each day. Thus, to achieve more
accurate adjustments for
MAIN MENU
parameters, allow the LCD
monitor to warm up (be On) for
at least 15 minutes before
making any screen adjustments.
i
BRIGHTNESS
OSD functions
Controls and
Adjustments
OSD Icon
Description
Sub-menu(s)
Adjusts brightness
BRIGHTNESS
CONTRAST
Adjusts contrast
The image lock function is used to
adjust the level of noise in the video
signal which causes horizontal lines or
areas on the screen where the image
appears to be unstable and jitters or
shimmers. This can be done
Automatic adjustment
Automatic
IMAGE LOCK
automatically or manually.
16
Controls and
Adjustments
OSD Icon
Description
Sub-menu(s)
Manual -
Use the Arrow buttons to
adjust away the
interference. If
•
•
Fine
Coarse
IMAGE LOCK
(continued)
satisfactory results are
not obtained using the
Fine adjustment, use the
Coarse adjustment and
then use Fine again.
This function may
change the width of the
display image. Use the
H-Position function on
the Image Position
menu to center the
display image on the
screen.
Moves the screen left and right or up
and down.
H-Position
V-Position
Color Mode
IMAGE
POSITION
Select the Color Mode you find most
comfortable and then fine tune the
colors using the User Color Mode
menu, if necessary.
Mode 1
(Cool White)
COLOR
Mode 2
(Normal White)
Mode 3
(Warm White)
User Mode -
•
•
•
Red
Increases or decreases
redness
Green
Blue
Increases or decreases
greenness
Increases or decreases
blueness
17
Controls and
Adjustments
OSD Icon
RESET
Description
Sub-menu(s)
Color Reset
Resets the Brightness, Contrast and
Color settings.
NO - Does not make the
adjustment
YES - Resets the color
Resets the Image position settings
Geometry
Reset
NO - Does not make the
adjustment
YES - Resets the
geometry
Shows information about the
addressability and the horizontal and
vertical frequencies of the images
received from the computer or video
board.
i
INFORMATION
The language chosen affects only the
language of the OSD. It has no effect
on any software running on the
computer.
Select one of the five
languages to use for the
OSD.
LANGUAGE
Changes the position of the OSD on
the screen.
H-Position
V-Position
OSD MENU
POSITION
18
Further Information
Display modes
The display mode the monitor uses is controlled by the computer. Therefore,
you should refer to your computer documentation for details on how to
change display modes.
The image size, position and shape may change when the display mode
changes. This is normal and the image can be readjusted using AUTO SETUP
and the monitor controls.
Unlike CRT monitors, which require a high refresh rate to minimize flicker,
TFT technology is inherently flicker-free. If possible, configure your computer
for 1024 × 768 addressability at 60Hz vertical refresh rate.
For the display modes listed below, the screen image has been optimized
during manufacture.
Factory Set Display Modes
Addressability
Refresh Rate
Horizontal Frequency
640 × 350
640 × 480
640 × 480
640 × 480
720 × 400
800 × 600
800 × 600
800 × 600
800 × 600
832 × 624
1024 × 768†
1024 × 768
1024 × 768
70 Hz
60 Hz
72 Hz
75 Hz
70 Hz
75 Hz
72 Hz
60 Hz
56 Hz
75 Hz
60 Hz
70 Hz
75 Hz
31.5 kHz
31.5 kHz
37.9 kHz
37.5 kHz
31.5 kHz
46.9 kHz
48.1 kHz
37.9 kHz
35.2 kHz
49.7 kHz
48.4 kHz
56.5 kHz
60.0 kHz
† Recommended
Note: VESA timings are as detailed in the VESA “Display Monitor Timing
Specification”. Version 1.0, Revision 0.8, dated 09/17/98.
19
Power Management
If your computer has
previously been used
To benefit from power management, the monitor must be used in conjunction
with a computer that implements the Video Electronics Standards Association
(VESA) Display Power Management Signalling (DPMS) Standard.
with a CRT monitor and is
currently configured to a
display mode outside the
range that the Flat Panel
monitor can display, you
may need to re-attach the
CRT monitor temporarily
untilyouhavere-configured
the computer, preferably to
1024 x 768 at 60Hz.
The power management feature is invoked when the computer recognizes
that you have not used your mouse or keyboard for a user-definable period.
There are several states as described in the table below.
®
As an ENERGY STAR Partner, IBM has determined that this product meets the
®
ENERGY STAR guidelines for energy efficiency.
For optimal performance, you switch off your monitor at the end of each
working day, or whenever you expect to leave it unused for long periods
during the day.
Power
Indicator
Restoring
Operation
State
Screen
Normal
Blank
Compliance
On
Steady green
Steady amber
®
Press a key or
move the mouse.
ENERGY STAR
and NUTEK
Active Off
Off
®
Press a key or
move the mouse. ‡
ENERGY STAR
and NUTEK
Steady amber
Blank
‡ There may be a slight delay before the picture reappears.
Product Disposal
The fluorescent lamp in the liquid crystal display contains a small amount of
mercury. Dispose of it as required by local ordinances and regulations.
20
Troubleshooting
If you have a problem setting up or using your monitor, you may be able to
solve it yourself. Before calling your retailer or IBM, try the suggested actions
that are appropriate to your problem.
Possible
Cause
Problem
Suggested Action
Reference
ꢂ
Ensure that the
electrical outlet and the
monitor are both switched
on.
ꢂ
Check that the power
cord is firmly plugged into
the electrical outlet and the
power supply unit.
Connecting
your Monitor
section (page
6)
Screen is blank
and power
indicator is off
No power to
monitor
ꢂ
If the power cord plug
has a removable fuse,
replace it.
ꢂ
Try another power
cord.
ꢂ
Try another electrical
outlet.
Screen is blank
and power
indicator is
Brightness
and Contrast
may be too
low
User controls
section (page
10)
ꢂ
Adjust brightness and
contrast.
steady green
ꢂ
Press any key on the
keyboard or move the
mouse to restore
operation.
Power
Screen is blank
and power
indicator is
The monitor is
in the Power
Management
Standby state
management
section (page
16)
ꢂ
Check the Power
steady amber
Management software on
your computer
21
Possible
Cause
Problem
Suggested Action
Reference
ꢂ
Check that the signal
cable is firmly connected to
the computer.
Connecting
your Monitor
section (page
6)
The monitor is
not receiving
a video signal
ꢂ
Check that no pins are
Screen is blank
and power
indicator is
flashing green
every 0.5
bent in the signal cable
connector.
Display mode
of the
computer is
outside the
range of the
monitor
Further
second
ꢂ
Reconfigure the
computer to use a
information
section (page
15)
supported display mode.
ꢂ
Press any key on the
Screen is blank
and power
indicator is
amber every
0.5 or 1 second Off state
The monitor is
in the Power
Management
Suspend or
keyboard or move the
mouse to restore
operation.
Power
management
section (page
16)
ꢂ
Check the Power
Management software on
your computer.
ꢂ
Select IMAGE LOCK
User controls
section (page
10)
There is noise
in the video
signal
Image appears
to be smeared
menu in the OSD. Then
select MANUAL to adjust
FINE/COARSE settings.
User controls
section (page
10)
Image appears
to be
discolored
The Color
setting may
be incorrect
ꢂ
Adjust the Color
settings.
ꢂ
The LCD contains over 2,300,000 thin-
A few dots are
missing,
discolored, or
inappropriately
lighted.
film transistors (TFTs). A small number of
missing, discolored, or lighted dots may be
present on the screen, which is an intrinsic
characteristic of the TFT LCD technology
and is not an LCD defect.
22
Further Help
Product warranty and support information
The following information describes the technical support that is available for your product,
during the warranty period or throughout the life of the product. Refer to your IBM Statement of
Limited Warranty for a full explanation of IBM warranty terms.
Warranty information on the World Wide Web
machine_warranties/ contains a worldwide overview of the IBM Limited Warranty for IBM
Machines, a glossary of terms used in the Statement of Limited Warranty, Frequently Asked
Questions (FAQ), and links to Product Support Web pages. The IBM Statement of Limited
Warranty is available from this Web site in 29 languages in Portable Document Format (PDF).
Online technical support
Online technical support is available during the life of your product. Online assistance can be
obtained through the Personal Computing Support Web site and the IBM Automated Fax
System.
Online technical support
IBM Personal Computing Support Web site
IBM Automated Fax System
1-800-426-3395 (U.S. and Canada)
During the warranty period, assistance for replacement or exchange of defective components
is available. In addition, if your IBM option is installed in an IBM computer, you might be entitled
to service at your location. Your technical support representative can help you determine the
best alternative.
Telephone technical support
Installation and configuration support through the IBM HelpCenter« will be withdrawn or made
available for a fee, at IBM’s discretion, 90 days after the option has been withdrawn from
marketing. Additional support offerings, including step-by-step installation assistance, are
available for a nominal fee.
To assist the technical support representative, have available as much of the following
information as possible:
·
·
·
·
·
Option name
Option number
Proof of purchase
Computer manufacturer, model, serial number (if IBM), and manual
Exact wording of the error message (if any)
23
·
·
Description of the problem
Hardware and software configuration information for your system
If possible, be at your computer. Your technical support representative might want to walk you
through the problem during the call.
For the support telephone number and support hours by country, refer to the following table. If
the number for your country or region is not listed, contact your IBM reseller or IBM marketing
representative. Response time may vary depending on the number and nature of the calls
received.
Support 24 hours a day, 7 days a week
Canada (Toronto only)
Canada (all others)
416-383-3344
1-800-565-3344
1-800-772-2227
U.S.A. and Puerto Rico
All other countries and regions
,and click Support Phone List.
More help, late-breaking
news and details of the
Changing cables
This product is shipped with the signal cable and the power cord attached to
the monitor. If you want to use other cables, follow the instructions below:
latest accessories for these
products may be found on the
worldwide web at:
1. Disconnect the power cord from the wall outlet.
accessories
2. Carefully insert the head of a flathead (–) screwdriver into the slot visible
along either side of the cable cover (a) and pry it off.
Information about the Video
Electronics Standards
Association can be found on the
worldwide web at:
a
b
c
24
3. Squeeze the sides of the hinge cover (b) and pull it off.
4. Gently lift the stand cover (c) along the top and then slide it backwards
and off the stand.
5. Remove the signal cable from the monitor and connect the new cable.
6. Slide the stand cover back on the stand.
7. Put the hinge cover back on, making sure that the straight side is at the
top.
8. Insert the three tabs at the top of the cable cover into the slots in the
back of the monitor and push the cover into place.
To obtain the correct cables and/or to get further instructions on installing
them, call the IBM HELPCENTER at the above numbers or contact your
dealer, retailer, or other IBM authorized Servicer.
25
Specifications
This color monitor (Type-model 9512-Ax0) uses a 15-inch TFT LCD
Dimensions
Width:
Depth:
Height:
365.2 mm (14.38 in.)
202.1 mm ( 7.96 in.)
344.8 mm (13.57 in.)
Weight
Tilt
Unpackaged:
Packaged:
4.1 Kg (9.03 lb)
5.3 Kg (11.68 lb)
Forward Tilt:
Backward tilt:
– 4°
+ 41°
Image
Viewable Image Size:
Maximum Height:
Maximum Width:
Pixel Pitch:
381 mm (15 in.)
228.1 mm (8.98 in.)
304.1 mm (11.97 in.)
0.297 mm (H) × 0.297 mm (V)
( 0.012 in.(H) x 0.012 in.(V) )
Power Input
Supply Voltage:
100 - 240 V ac
60/50 ± 3 Hz
Max Supply Current:
1.0 A at 120 V ac
Power Consumption
Video Input
Normal Operation:
Active Off:
Off:
< 30 W
< 2 W
< 2 W at 220 V ac & < 1 W at 100 V ac
Input Signal:
Analog Direct Drive
75 ohm 0.7 V
Horizontal Addressability:
Vertical Addressability:
Clock Frequency:
1024 pixels (maximum)
768 lines (maximum)
78 MHz
Communications
VESA DDC:
EDDC
Supported Display
Modes
VESA Standard 12 modes
Macintosh 1 mode
See Further Information
Environment
Temperature:
Operating:
Storage:
10 to 35° C ( 50 to 95° F)
- 20 to 60° C ( -4 to 140° F)
- 20 to 60° C ( -4 to 140° F)
Shipping:
Humidity:
Operating:
Storage:
10 to 80%
5 to 95%
5 to 95%
Shipping:
26
Service Information
The following parts are for use by IBM service, or IBM authorized dealers, to support
the customer warranty. Parts are for service use only.
Flat Panel Monitor, Type 9512
31P7164
31P7165
31P7166
31P7167
31P7168
31P7169
31P7170
31P7171
9512-AB0
9512-AW0
9512-DB0
9512-DW0
9512-AB0/9512-DB0
9512-AW0/9512-DW0
9512-AB0
Monitor - Stealth Black
Monitor - Pearl White
Monitor - Stealth Black
Monitor - Pearl White
Tilt/Swivel Base - Stealth Black
Tilt/Swivel Base - Pearl White
Power Supply - Stealth Black
Power Supply - Pearl White
9512-AW0
27
Notices and trademarks
This section contains information on notices and trademarks.
Notices
IBM may not offer the products, services, or features discussed in this document in all
countries. Consult your local IBM representative for information on the products and services
currently available in your area. Any reference to an IBM product, program, or service is not
intended to state or imply that only that IBM product, program, or service may be used. Any
functionally equivalent product, program, or service that does not infringe any IBM intellectual
property right may be used instead. However, it is the user’s responsibility to evaluate and
verify the operation of any non-IBM product, program, or service.
IBM may have patents or pending patent applications covering subject matter described in this
document. The furnishing of this document does not give you any license to these patents. You
can send license inquiries, in writing, to:
IBM Director of Licensing
IBM Corporation
North Castle Drive
Armonk, NY 10504-1785
U.S.A.
The following paragraph does not apply to the United Kingdom or any country where
such provisions are inconsistent with local law: INTERNATIONAL BUSINESS MACHINES
CORPORATION PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY
KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied
warranties in certain transactions, therefore, this statement may not apply to you.
This information could include technical inaccuracies or typographical errors. Changes are
periodically made to the information herein; these changes will be incorporated in new editions
of the publication. IBM may make improvements and/or changes in the product(s) and/or the
program(s) described in this publication at any time without notice.
IBM may use or distribute any of the information you supply in any way it believes appropriate
without incurring any obligation to you.
Any references in this publication to non-IBM Web sites are provided for convenience only and
do not in any manner serve as an endorsement of those Web sites. The materials at those
Web sites are not part of the materials for this IBM product, and use of those Web sites is at
your own risk.
28
Compliances
Federal Communications Commission (FCC) Declaration of Conformity
IBM T541A or T541D Color Monitor 9512-Ax0 and 9512-Dx0
Tested To Comply
With FCC Standards
FOR HOME OR OFFICE USE
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•
Consult an IBM authorized dealer or service representative for help.
Properly shielded and grounded cables and connectors must be used in order to meet FCC
emission limits. Proper cables and connectors are available from IBM authorized dealers. IBM
is not responsible for any radio or television interference caused by using other than
recommended cables and connectors or by unauthorized changes or modifications to this
equipment. Unauthorized changes or modifications could void the user’s authority to operate
the equipment.
1
Declaration of Conformity
Trade name: IBM Corporation
Model Nos.: 9512-Ax0 & 9512-Dx0
Responsible Party: Samsung Electronics Co.,Ltd.
Address: QA Lab of Samsung America
Telephone No.: 408-554-5124
This Device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device
must accept any interference received, including interference
that may cause undesired operation.
Power Cords
For your safety, IBM provides a power cord with a grounded attachment plug to use with this
IBM product. To avoid electrical shock, always use the power cord and plug with a properly
grounded power outlet.
IBM power cords used in the United States and Canada are listed by the Underwriter’s
Laboratories (UL) and certified by the Canadian Standards Association (CSA).
For units intended to be operated at 115 volts: Use a UL-listed and CSA-certified cord set
consisting of a minimum 18 AWG, Type SVT or SJT, three-conductor cord, a maximum of 15
feet in length and a parallel blade, grounding-type attachment plug rated 15 amperes, 125 volts.
For units intended to be operated at 230 volts (U.S. use): Use a UL-listed and CSA-certified
cord set consisting of a minimum 18 AWG, type SVT or SJT, three-conductor cord, a maximum
of 15 feet in length and a tandem blade, grounding-type attachment plug rated 15 amperes, 250
volts.
For units intended to be operated at 230 volts (outside the U.S.): Use a cord set with a
grounding-type attachment plug. The cord set should have the appropriate safety approvals for
the country in which the equipment will be installed.
IBM power cords for a specific country or region are usually available only in that country or
region.
2
IBM
Used in these countries or regions
power
cord part
number
13F9959
Antigua, Aruba, Bahamas, Barbados, Belize, Bermuda, Bolivia, Brazil, Caicos Island, Canada, Cayman
Islands, Costa Rica, Columbia, Dominican Republic, Guam, Ecuador, El Salvador, Guatemala, Haiti,
Honduras, Jamaica, Japan, Mexico, Netherlands Antilliles, Nicaragua, Panama, Peru, Phillipines, Saudi
Arabia, Thailand, Taiwan, United States, Venezuela
1838576
13F9978
Antigua, Aruba, Bahamas, Barbados, Belize, Bermuda, Bolivia, Brazil, Caicos Island, Canada, Cayman
Islands, Costa Rica, Columbia, Dominican Republic, Guam, Ecuador, El Salvador, Guatemala, Haiti,
Honduras, Jamaica, Japan, Mexico, Netherlands Antilliles, Nicaragua, Panama, Peru, Phillipines, Taiwan,
United States, Venezuela
Afghanistan, Albania, Algeria, Andorra, Angola, Armenia, Austria, Azerbaidjan, Belarus, Benin, Belgium,
Bosnia, Burkina Faso, Burundi, Cameroon, Cambodia, Cape Verde, Central African Republic, Chad,
Congo (Republic of), Comoros, Congo (Democratic Republic of), Cote D'Ivoire (Ivory Coast), Croatia,
Czech Rep, Dahomey, Djibouti, Equatorial Guinea, Eqypt, Eritrea, Estonia, Ethiopia, Finland, France,
French Guyana, French Polynesia, Gabon, Georgia, Germany, Greece, Guadeloupe, Guinea, Guinea
Bissau, Hungary, Iceland, Indonesia, Iran, Kazakhstan, Korea (South), Kyrgyzstan, Laos, Latvia,
Lebanaon, Lithuania, Luxemborg, Macedonia, Madagascar, Mali, Martinique, Mauritania, Mauritus,
Mayotte, Moldavia, Monaco, Mongolia, Morocco, Mozambique, Netherlands, New Caledonia, Niger,
Nigeria, Norway, Poland, Portugal, Reunion, Romania, Russia, Rwanda, Sao Tome, Saudi Arabia,
Senegal, Serbia, Slovakia, Solvenia, Somalia, Spain, Suriname, Sweden, Syria, Tajikistan, Togo, Tunisia,
Turkey, Turkmenistan, Ukraine, Upper Volta, USSR (C.I.S.), Uzbekistan, Vanuatu, Vietnam, Wallia and
Futuna, Yugoslavia, Zaire
13F9996
14F0050
14F0086
14F0068
14F0014
Denmark
Lichtenstein, Switzerland
Israel
Chile, Italy, Libya
Bangladesh, India, Lesotho, Maldives, Nambia, Nepal, Pakistan, Samoa, South Africa, Sri Lanka,
Swaziland, Uganda
14F0032
Bahrain, Brunei, Botswana, Channel Islands, Cyprus, Dominica, Gambia, Ghana, Grenada, Guyana, Hong
Kong, Iraq, Ireland, Jordan, Kenya, Kuwait, Liberia, Malawi, Malaysia, Malta, Myanmar (Burma), Nigeria,
Oman, Qatar, Seychelles, Saint Kitts & Nevis, Saint Lucia, Saint Vincent and the Grenadines, Sierra
Leone, Singapore, Sudan, Tanzania, Trinidad & Tobago, United Arab Emirate (Dubai), United Kingdom,
Yemen, Zambia, Zimbabwe
13F9939
02K0545
36L8879
Australia, Fiji, New Zealand, Papua New Guinea
China
Argentina, Paraguay, Uruguay
Industry Canada Class B emission compliance statement
This Class B digital apparatus complies with Canadian ICES-003.
3
Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le
matériel brouilleur du Canada.
Avis de conformité à la réglementation d'Industrie Canada
Cet appareil numérique de classe B est conforme à la norme NMB-003 du Canada.
4
TCO Compliances Section
Models 9512-Ax0 and 9512-Dx0
comply with TCO ’95 guidelines.
Model 9512-Ax0 and 9512-Dx0
comply with TCO ’99 guidelines
Congratulations!
You have just purchased a TCO’95 or TCO’99 approved and labeled product! Your choice has
provided you with a product developed for professional use. Your purchase has also contributed
to reducing the burden on the environment and also to the further development of
environmentally adapted electronics products.
Why do we have environmentally labeled computers?
In many countries, environmental labeling has become an established method for encouraging
the adaptation of goods and services to the environment. With the growing manufacture and
usage of electronic equipment throughout the world, there is a recognized concern for the
materials and substances used by electronic products with regards to their eventual recycling
and disposal. By proper selection of these materials and substances, the impact on the
environment can be minimized.
There are also other characteristics of a computer, such as energy consumption levels, that are
important from the viewpoints of both the work (internal) and natural (external) environments.
Electronic equipment in offices is often left running continuously, resulting in unnecessary
consumption of large amounts of energy and additional power generation. From the standpoint
of carbon emissions alone, it is vital to save energy.
What does labeling involve?
This product meets the requirements for the TCO’95 or TCO’99 scheme which provides for
international and environmental labeling of personal computers. The labeling scheme was
developed as a joint effort by the TCO (The Swedish Confederation of Professional
Employees), Svenska Naturskyddsforeningen (The Swedish Society for Nature Conservation)
and Statens Energimyndighet (The Swedish National Energy Administration)
5
Approval requirements cover a wide range of issues: environment, ergonomics, emission of
electric and magnetic fields, energy consumption and electrical safety.
Environmental criteria impose restrictions on the presence and use of heavy metals, brominated
and chlorinated flame retardants, CFCs (freons) and chlorinated solvents, and other materials .
The product must be prepared for recycling and the manufacturer is obliged to have an
environmental policy which must be adhered to in each country where the company implements
its operational policy.
Energy requirements include a demand that the computer and/or display, after a certain period
of inactivity, shall reduce its power consumption to a lower level in one or more stages. The
length of time to reactivate the computer shall be reasonable for the user.
Labeled products must meet strict environmental demands, for example, in respect of the
reduction of electric and magnetic fields as well as physical and visual ergonomics.
Below you will find a brief summary of the environmental requirements met by this product. The
complete environmental criteria document may be ordered from:
TCO Development
SE-114 94 STOCKHOLM, Sweden
Fax: +46 8 782 92 07
E-mail (Internet): [email protected]
Current information regarding TCO’99 approved and labeled products may also be obtained via
Environmental requirements
Flame retardants
Flame retardants are present in printed circuit boards, cables, wires, casings and housings.
Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a
computer casing can consist of flame retardant substances. Most flame retardants contain
bromine or chlorine, and those flame retardants are chemically related to PCBs. Both the flame
retardants containing bromine or chlorine and the PCBs are suspected of giving rise to health
effects, including reproductive damage in fish-eating birds and mammals, due to the bio-
accumulative* processes when not disposed of in accordance with strict standards for disposal.
________________________________
*Bio-accumulative is defined as substances which accumulate within living organisms.
6
The relevant TCO’99 demand requires that plastic components weighing more than 25 grams
must not contain flame retardants with organically bound bromine or chlorine. Flame retardants
are allowed in the printed circuit boards since no substitutes are available.
Cadmium**
Cadmium is present in rechargeable batteries and in the colour-generating layers of certain
computer displays.
The relevant TCO’99 requirement states that batteries, the colour-generating layers of display
screens and the electrical or electronics components must not contain any cadmium.
Mercury**
Mercury is sometimes found in batteries, relays and switches. The relevant TCO’99 requirement
states that batteries may not contain any mercury. It also demands that mercury is not present
in any of the electrical or electronics components associated with the labeled unit. There is
however one exception. Mercury is, for the time being, permitted in the back light system of flat
panel monitors as there today is no commercially available alternative. TCO aims on removing
this exception when a mercury free alternative is available.
CFCs (freons)
The relevant TCO’99 requirement states that neither CFCs nor HCFCs may be used during the
manufacture and assembly of the product or in its packaging. CFCs (freons) are sometimes
used for washing printed circuit boards. CFCs break down ozone and thereby damage the
ozone layer in the stratosphere, causing increased reception on earth of ultraviolet light. This
restriction assures that further damage to the ozone layer form this type of equipment will be
eliminated.
**Lead, Cadmium and Mercury are heavy metals which are bio-accumulative.
7
Lead**
Lead can be found in picture tubes, display screens, solders and capacitors. The relevant
TCO’99 requirement permits the inclusion of lead since no replacement has yet been
developed.
_____________________________
**Lead, Cadmium and Mercury are heavy metals which are bio-accumulative.
ENERGY STAR Compliances Section
As an ENERGY STAR Partner,
IBM Corporation has
determined that this product
meets the ENERGY STAR
guidelines for energy efficiency
Congratulations!
You have just purchased an ENERGY STAR qualified product
What is an ENERGY STAR qualified product?
The ENERGY STAR program is a voluntary partnership between the U.S. Environmental
Protection Agency / Dept. of Energy and Partners to reduce pollution and save energy. An
ENERGY STAR qualified product meets or exceeds the energy criteria defined in an MOU
(Memorandum of Understanding) for that product category. As an ENERGY STAR Partner, IBM
offers ENERGY STAR qualified computers, monitors and printers that meet the growing
performance and networking needs of customers while reducing energy use, saving you money
and improving the environment.
IBM is a recognized leader in providing energy efficient office products. In 1998 and 1999, IBM
received the ENERGY STAR Computer Partner of the Year award in the office equipment
category and in 2001, IBM received the first ENERGY STAR Excellence in Corporate Commitment
award. ENERGY STAR products save you more -- look for the ENERGY STAR label and program
information on IBM products, product literature, Web sites, packaging and promotional material.
ENERGY STAR
Current criteria and information regarding the ENERGY STAR program can be found at
ENERGY STAR and the ENERGY STAR logo are registered US marks.
This product complies with Swedish National Council for Metrology (MPR) standards issued in
December 1999 (MPRII) for very low frequency (VLF) and Extremely low frequency (ELF)
emissions.
8
Electronic emission notices
Hinweise
Gemäß der Amtsblätter des BMPT Nm. 61Ú1991 und 6Ú1992 wird der Betreiber darauf
aufmerksam gemächt, daß die von ihm mit diesem Gerät zusammengestellte Anlage auch den
technischen Bestimmungen dieser Amtsblätter genügen muß.
Aus ergonomischen Gründen wird empfohlen, die Grundfarbe Blau nicht auf dunklem
Untergrund zu verwenden (schlechte Erkennbarkeit, Augenbelastung bei zu geringem
Zeichenkontrast).
Aus ergonomischen Gründen sollten nur Darstellungen auf dunklem Hintergrund bei
Vertikalfrequenzen ab 60 Hz (ohne Zeilensprung) benutzt werden.
Die Konvergenz des Bildes kann sich auf Grund des Magnetfeldes am Ort der Aufstellung aus
der Korrekten Grundeinstellung verändern. Zur Korrektur empfiehlt es sich deshalb, die Regler
an der Frontseite für H STAT und V STAT so einzustellen, daß die getrennt sichtbaren
Farblinien für Rot. Grün und Blau bei z.B. der Darstellung eines Buchstabens zur Deckung
(Konvergenz) gelangen. Siehe hierzu auch die Erklärungen zu H STAT und V STAT.
European Union (EU) Statement
This product is in conformity with the protection requirements of the EU Council Directive
89/366/ECC on the approximation of the laws of the Member States relating to electromagnetic
compatibility
IBM can not accept responsibility for any failure to satisfy the protection requirements resulting
from a non-recommended modification of the product, including the fitting of non-IBM option
cards.
This product has been tested and found to comply with the limits for Class B Information
Technology Equipment according to CISPR 22 Ú European Standard EN55024:1998. The
limits for Class B equipment were derived for typical residential environments to provide
reasonable protection against interference with licensed communication devices.
Properly shielded and grounded cables and connectors must be used in order to reduce the
potential for causing interference to radio and TV communications and to other electrical or
electronic equipment. Such cables and connectors are available from IBM authorised dealers.
In accordance with EN 55024:1998 1992, Performance Criterion A:, it should be noted that in
the presence of certain electromagnetic fields, some screen jitter may be observed.
9
Spécifications de la CEE
Ce produit est conforme aux exigences de protection de la directive 89/ 336/ EEC du Conseil de
l’UE sur le rapprochement des lois des États membres en matière de compatibilité
électromagnétique.
IBM ne peut accepter aucune responsabilité pour le manquement aux exigences de protection
résultant d’une modification non recommandée du produit, y compris l’installation de cartes
autres que les cartes IBM.
Ce produit a été testé et il satisfait les conditions de l’équipement informatique de Classe B en
vertu de CISPR22 / Standard européen EN55024:1998. Les conditions pour l’équipement de
Classe B ont été définies en fonction d’un contexte résidentiel ordinaire afin de fournir une
protection raisonnable contre l’interférence d’appareils de communication autorisés.
Des câbles blindés et correctment reliés à la terre doivent être utilisés pour réduire les risques
d’interférence avec des communications radio et télévisées, ainsi qu’avec des équipements
électriques ou électroniques. Ces
câbles et connecteurs sont disponibles auprés de vos revendeurs IBM agréés.
Conformément à la norme EN 55024:1998 (Critére de Performance A), l’utilisateur doit être
conscient du fait qu’en présence de certains champs électromagnétiques, l’image peut être
instable.
Erklärung für die Europäische Union (EU)
Zulassungbescheinigunglaut dem Deutschen Gesetz über die elektromagnetische
Verträglichkeit von Geräten (EMVG) vom 30. August 1995 (bzw. der EMC EG Richtlinie
89/336):
Dieses Gerät ist berechtigt in Übereinstimmungmit dem Deutschen EMVG das EG-
Konformitätszeichen - CE - zu führen.
Verantwortlich für die Konformitätserklärung nach Paragraph 5 des EMVG ist die:
IBM Deutschland Informationssysteme GmbH, 70548 Stuttgart.
Informationen in Hinsicht EMVG Paragraph 3 Abs. (2) 2:
Das Gerät erfüllt die Schutzanforderungen nach EN
55024:1998 und EN55024:1998 Klasse B.
EN 55082 Hinweis:
“Wird dieses Gerät in einer industriellen Umgebung betrieben (wie in EN 55082:B festgetlegt),
dann kann es dabei eventuell gestört werden. In solch einem FAll ist der Abstand bzw. die
Abschirmungzu der industriellen Störquelle zu vergrößern.”
10
Anmerkung:
Um die Einhaltung des EMVG sicherzustellen sind die Geräte, wie in den IBM Handbüchern
angegeben, zu installieren und zu betreiben.
Declaración de la Unión Europea (UE)
Este producto satisface los requisitos de protección del Consejo de la UE, Directiva 89/ 336/
CEE en lo que a la le gislatura de los Estados Miembros sobre compatibilidad electroma
gnética se refiere.
IBM no puede aceptar responsabilidad al guna si este producto deja de satisfacer dichos
requisitos de protección como resultado de una modificación no recomendada del producto,
inclu yendo el ajuste de tarjetas de opción que no sean IBM.
Este producto ha sido probado y satisface los límites para Equipos Informáticos Clase B de
conformidad con el Estándar CISPR22 y el Estándar Europeo EN55024:1998. Los límites para
los equipos de Clase B se han establecido para entornos residenciales típicos a fin de
proporcionar una protección razonable contra las interferencias con dispositivos de
comunicación licenciados.
Se deben utilizar concetores y cables debidamente protegidos y conectados a tierra a fin de
reducir las posibilidades de que se produzcan interferencias con comunicaciones por radio o
televisión y otros equipos eléctricos o electrónicos. Este tipo de cables y conectores pueden
adquirirse en concesionarios autorizados de IBM.
De acuerdo con la norma EN 55024:1998, Performance Criterion A, habría que destacar que
en presencia de determinados campos electroma gnéticos, podría observarse una marcada
inestabilidad e la imagen.
Dichiarazione di conformità dell’Unione Europea (EU)
Questo prodotto è conforme alle normative di protezione ai sensi della Direttiva del Consi glio
dell’Unione Europea 89/ 336/ CEE sull’armonizzazione le gislativa degli stati membri in materia
di compatibilità elettromagnetica.
IBM non accetta responsabilità alcuna per la mancata conformità alle normative di protezione
dovuta a modifiche non consi gliate al prodotto, compresa l’installazione di schede e
componenti di marca diversa da IBM.
Le prove effettuate sul presente prodotto hanno accertato che esso rientra nei limiti stabiliti per
le le apparecchiature di informatica Classe B ai sensi del CISPR 22 / Norma Europea
EN55024:1998. I limiti delle apparecchiature della Classe B sono stati stabiliti al fine di fornire ra
11
gionevole protezione da interferenze mediante dispositivi di comunicazione in concessione in
ambienti residenziali tipici.
Utilizzare cavi e connettori colle gati a terra per ridurre il rischio potenziale di interferenza delle
comunicazioni radiotelevisive e di a; tri apparecchi elettrici o elettronici. I cavi sono disponibili
presso i rivenditori IBM.
In accordo con quando previsto nel documento EN 55024:1998, Performance Criterion A, é
importante sottolineare che in presenza di determinati campi elettroma gnetici é possibile che si
verifichi un certo tremolio delle immagini.
Europeiska unionen (EU)
Denna produkt har testats och följer gränsvärdena för Klass B Information Technology
Equipment enligt CISPR 22 Ú Europeisk standard EN55024:1998. Gränsvärden för Klass B-
utrutning utgår frår vanliga bostadsomräden för att ge ett rimligt skydd mot störningar i
kommunikationsenheter.
Korrekt avskärmade och jordade kablar och kontakter måste användas för att minska risken för
störningar i radio- och TV-kommunikationer och annan elektrisk utrustning. Sådana kablar och
kontakter finns tillgängliga hos auktoriserade IBM-återförsäljare.
I enlighet med EN 55024:1998 1992, Performance Criterion A påpekas följande: I närheten av
en del elektromagnetiska fält kan vissa bildstörningar uppstår på skårmen.
Deutsche EMV-Direktive (electromagnetische Verträglichkeit)
Dieses Gerät ist berechtigt in Übereinstimmung mit dem deutschen EMVG vom 9.Nov.92 das
EG-Konformitätszeichen zu führen.
Der Aussteller der Konformitätserklärung ist die IBM UK, Greenock.
Dieses Gerät erfüllt die Bedingungen der EN55024:1998 Klasse B.
VCCI Class B Notice (Japan Only)
This equipment complies with the limits for a Class B digital device (devices used in or adjacent
to a residential environment) and conforms to the standards for information technology
equipment that are set by the Voluntary Control Council for Interference for preventing radio
frequency interference in residential areas.
12
Japanese statement of compliance for products less than or equal to 20 A per phase:
13
Trademarks
The following terms, used in this publication, are trademarks or service marks
of the IBM Corporation in the United States, other countries, or both:
HelpCenter IBM
ENERGY STAR is a U.S. Govt. registered trademark.
Microsoft, Windows, and Windows NT are trademarks of Microsoft
Corporation in the United States, other countries, or both.
Other company, product, and service names may be trademarks or service
marks of others.
© Copyright International Business Machines Corporation 2002. All
rights reserved.
29
|