Operating Instructions
HOB
Contents
GB
Warnings, 2
GB
Installation, 3-6
Positioning
English,1
Gas connection
Data plate
Burner and nozzle specifications
Electrical connection, 7
Description of the appliance, 8
Overall view
Start-up and use, 9-10
Practical advice on using the burners
Precautions and tips, 11
General safety
GC640IX
GC640WH
GC640BK
GC751TX
GC760FX
GC750X
GC730RTX
GC640TIX
GC750TIX
GC641IX
Disposal
Recycling & Disposal Information
Maintenance and care, 12
Switching the appliance off
Cleaning the appliance
Gas tap maintenance
Troubleshooting, 13
After Sales Service, 14
Repair Service and Information Desk
Extended Warranties
Genuine Parts and Accessories
Guarantee, 15
08448 24 24 24
Please phone us on
guarantee
to activate your
Installation
! Before operating your new appliance please read this
instruction booklet carefully. It contains important information
for safe use, installation and care of the appliance.
also be equipped with vents to allow gas to escape in the
event of a leak. As a result LPG cylinders, whether
partially or completely full, must not be installed or stored
in rooms or storage areas that are below ground level
(cellars, etc.). It is advisable to keep only the cylinder
being used in the room, positioned so that it is not
subject to heat produced by external sources (ovens,
fireplaces, stoves, etc. ) which could raise the
GB
! Please keep these operating instructions for future
reference. Pass them on to possible new owners of the
appliance.
Positioning
! Keep packaging material out of the reach of children. It
can become a choking or suffocation hazard (see
Precautions and tips).
temperature of the cylinder above 50°C.
Fitting the appliance
Gas and mixed hobs are manufactured with type X degree
protection against overheating. The following precautions
must be taken when installing the hob:
! The appliance must be installed by a qualified professional
according to the instructions provided. Incorrect installation
may cause harm to people and animals or may damage
property.
• Kitchen cabinets adjacent to the appliance and taller
than the top of the hob must be at least 600 mm from the
edge of the hob.
! This unit may be installed and used only in permanently
ventilated rooms in accordance with British Standard Codes
Of Practice: B.S. 6172 / B.S. 5440, Par. 2 and B.S. 6891
Current Editions. The following requirements must be
observed:
• Hoods must be installed according to their relative
installation instruction manuals and at a minimum
distance of 650 mm from the hob.
• Place the wall cabinets adjacent to the hood at a
• The room must be equipped with an air extraction system
that expels any combustion fumes. This may consist of a
hood or an electric fan that automatically starts each time
the appliance is switched on.
minimum height of 420 mm from the hob (see figure).
If the hob is installed beneath a
wall cabinet, the latter must be
situated at a minimum of 700 mm
600mm min.
above the hob (see figure).
In a chimney stack or branched flue.
(exclusively for cooking appliances)
Directly to
the Outside
• The installation cavity should have the dimensions
indicated in the figure.
• The room must also allow proper air circulation, as air is
needed for combustion to occur normally. The flow of air
Fastening hooks are provided, allowing you to fasten the
hob to tops that are between 20 and 40 mm thick. To
ensure the hob is securely fastened to the top, we
recommend you use all the hooks provided.
555 mm
3
must not be less than 2 m /h per kW of installed power.
The air circulation system may
take air directly from the outside
by means of a pipe with an inner
2
cross section of at least 100 cm ;
A
55 mm
the opening must not be
vulnerable to any type of
Examples of ventilation holes
for comburant air.
475 mm
blockages.
Adjacent
Room
Room to be
Vented
The system can also provide the
air needed for combustion
Hook fastening diagram
indirectly, i.e. from adjacent rooms
fitted with air circulation tubes as
described above. However, these
rooms must not be communal
rooms, bedrooms or rooms that
may present a fire hazard.
Enlarging the ventilation slot
between window and floor.
Hooking position
Hooking position
for top H=20 mm
for top H=30 mm
• Liquid petroleum gas sinks to the floor as it is heavier
than air. Therefore, rooms containing LPG cylinders must
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
3
Front
! Check that the pressure of the gas supply is consistent
with the values indicated in Table 1 (“Burner and nozzle
specifications”). This will ensure the safe operation and
longevity of your appliance while maintaining efficient
energy consumption.
GB
Connection with a rigid pipe (copper or steel)
! Connection to the gas system must be carried out in such
a way as not to place any strain of any kind on the
appliance.
Hooking position
Back
There is an adjustable L-shaped pipe fitting on the
appliance supply ramp and this is fitted with a seal in
order to prevent leaks. The seal must always be replaced
after rotating the pipe fitting (seal provided with
appliance). The gas supply pipe fitting is a threaded 1/2
gas cylindrical male attachment.
for top H=40 mm
! Use the hooks contained in the “accessory pack”
• Where the hob is not installed over a built-in oven, a
wooden panel must be installed as insulation. This
must be placed at a minimum distance of 20 mm from
the lower part of the hob.
Connecting a flexible jointless stainless steel pipe to a
threaded attachment
Ventilation
The gas supply pipe fitting is a threaded 1/2 gas cylindrical
male attachment.
To ensure adequate ventilation, the back panel of the
cabinet must be removed. It is advisable to install the
oven so that it rests on two strips of wood, or on a
completely flat surface with an opening of at least 45 x
560 mm (see diagrams).
These pipes must be installed so that they are never
longer than 2000 mm when fully extended. Once
connection has been carried out, make sure that the
flexible metal pipe does not touch any moving parts and
is not compressed.
! Only use pipes and seals that comply with current
560 mm.
national regulations.
Checking the tightness of the connection
! When the installation process is complete, check the
pipe fittings for leaks using a soapy solution. Never use a
flame.
When installing the cooktop above a built-in oven
without forced ventilation, ensure that there are air
inlets and outlets for ventilating the interior of the
cabinet adequately.
Adapting to different types of gas
To adapt the hob to a different type of gas other than
default type (indicated on the rating plate at the base of
the hob or on the packaging), the burner nozzles should
be replaced as follows:
1. Remove the hob grids and slide the burners off their
seats.
2. Unscrew the nozzles using a 7 mm socket spanner,
and replace them with nozzles for the new type of gas
(see table 1 “Burner and nozzle characteristics”).
3. Reassemble the parts following the above procedure in
the reverse order.
Gas connection
4. Once this procedure is finished, replace the old rating
sticker with one indicating the new type of gas used.
Sticker are available from any of our Service Centres.
The appliance should be connected to the main gas
supply or to a gas cylinder in compliance with current
national regulations. Before carrying out the connection,
make sure the cooker is compatible with the gas supply
you wish to use. If this is not the case, follow the
instructions indicated in the paragraph “Adapting to
different types of gas.”
Replacing the nozzles on separate “double flame “
burners:
1. remove the grids and slide the burners from their
housings. The burner consists of 2 separate parts (see
figure);
When using liquid gas from a cylinder, install a pressure
regulator which complies with current national regulations.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
4
2. unscrew the burers with a 7 mm wrench spanner. The
internal burner has a nozzle, the external burner has
two (of the same size). Replace the nozzle with models
suited to the new type of gas (see table 1).
• Setting the burners to minimum:
GB
1. Turn the tap to the low flame position.
2. Remove the knob and adjust
the adjustment screw, which is
positioned in or next to the tap
pin, until the flame is small but
steady.
3. replace all the components by repeating the steps in
reverse order.
3. Having adjusted the flame to the required low setting,
while the burner is alight, quickly change the position of
the knob from minimum to maximum and vice versa
several times, checking that the flame does not go out.
Replacing the Triple ring burner nozzles
4. Some appliances have a safety device (thermocouple)
fitted. If the device fails to work when the burners are
set to the low flame setting, increase this low flame
setting using the adjusting screw.
1. Remove the pan supports and lift the burners out of
their housing. The burner consists of two separate parts
(see pictures).
2. Unscrew the nozzles using a 7 mm socket spanner.
Replace the nozzles with models that are configured
for use with the new type of gas (see Table 1). The two
nozzles have the same hole diameter.
5. Once the adjustment has been made, replace the seals
on the by-passes using sealing wax or a similar
substance.
! If the appliance is connected to liquid gas, the regulation
3. Replace all the components by completing the above
operations in reverse order.
screw must be fastened as tightly as possible.
! Once this procedure is finished, replace the old rating
sticker with one indicating the new type of gas used.
Stickers are available from any of our Service Centres.
! Should the gas pressure used be different (or vary
slightly) from the recommended pressure, a suitable
pressure regulator must be fitted to the inlet pipe (in order
to comply with current national regulations).
• Adjusting the burners’ primary air :
Does not require adjusting.
DATA PLATE
Electrical
see data plate
connections
This appliance conforms to the following
European Economic Community directives:
- 2006/95/EEC dated 12/12/06 (Low
Voltage) and subsequent amendments
- 2004/108/EEC dated 15/12/04
(Electromagnetic Compatibility) and
subsequent amendments
- 93/68/EEC dated 22/07/93 and
subsequent amendments.
- 2009/142/EEC dated 30/11/09 (Gas) and
subsequent amendments.
- 2002/96/EC and subsequent
amendments.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
5
Burner and nozzle specifications
GB
Table 1
Liquid Gas
Natural Gas
Burner
Diameter Thermal
Thermal By-pass Nozzle
Flow*
(g/h)
Thermal Nozzle
Flow*
(l/h)
power
kW
power
kW
1/100
1/100
power
kW
1/100
(p.c.s.*)
Reduced Nominal (mm)
(p.c.s.*)
(p.c.s.*)
Nominal
(mm)
100
100
75
(mm)
86
***
**
(mm)
132 (H)
122 (H)
96
Fast (R)
0.70
0.70
0.40
0.40
1.50
0.70
0.70
0.40
3.00
2.60
1.65
1.00
3.30
3.40
1.50
0.90
39
39
28
28
61
39
39
28
218
189
120
73
214
186
118
71
3.00
2.60
1.65
1.00
3.60
3.40
1.50
0.90
286
248
157
95
Reduced Fast (RR)
Semi Fast (S)
80
64
Auxiliary (A)
55
50
79 (6)
103x2
138 (H)
88
Triple Crown (TC)
Ultrarapid (UR)
Semi-Fishburner (SP)
130
100
—
65x2
91
240
247
109
65
236
243
107
64
343
324
143
86
60
Double Flame
(DCDR Internal)
30
44
74
Double Flame
(DCDR External)
2 nozzle
130
1.50
4.10
61
70x2
298
293
4.10
110x2
390
Nominal (mbar)
Minimum (mbar)
Maximum (mbar)
28-30
20
35
37
25
45
20
17
25
Supply pressures
*
**
***
At 15°C and 1013 mbar - dry gas
Propane P.C.S. = 50.37 MJ/Kg
Butane P.C.S. = 49.47 MJ/Kg
Natural P.C.S. = 37.78 MJ/m³
RR
RR
A
RR
A
S
A
S
S
S
S
S
SP
SP
DC
TC
UR
TC
A
GC730RTX
GC750X
A
GC751TX
GC750TIX
GC760FX
A
RR
TC
R
S
S
S
GC640IX
GC640WH
GC640BK
GC641IX
GC640TIX
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
6
Electrical Connection
! THIS APPLIANCE MUST BE EARTHED.
! The wires in the mains lead are coloured in
GB
The hob is designed to work with alternating current,
the supply voltage and frequency indicated on the
rating plate (situated under the hob). Make sure that
the local supply voltage corresponds to the voltage
indicated on the rating plate.
accordance with the following code:
Green & Yellow
Blue
- Earth
- Neutral
- Live
Brown
As the colours of the wires in the mains lead may
not correspond with the coloured markings
identifying the terminals in your plug, proceed as
follows:
Connecting the supply cable to the mains
electricity supply
Connect the Green & Yellow wire to terminal marked
For models supplied without a plug, fit a standard
plug suitable for the load indicated on the rating
plate, onto a cable and connect to a suitable socket.
To connect direct to the mains supply, a double pole
switch with a contact separation of at least 3mm
suitable for the load and complying with current
standards and regulations must be fitted between
the appliance and the mains supply outlet.
The green-yellow earth wire must not be interrupted
by the switch.
“E” or
or coloured Green or Green & Yellow.
Connect the Brown wire to the terminal marked “L” or
coloured Red or Brown.
Connect the Blue wire to the terminal marked “N” or
coloured Black or Blue.
FAILURE TO OBSERVE THE ACCIDENT-
PREVENTION REGULATIONS RELIEVES THE
MANUFACTURER OF ALL LIABILITY.
Replacing the cable
The supply cable must be positioned so that no part
of it reaches a temperature of 50°C above room
temperature. For installation above a built-under
oven, the hob and the oven must be connected
separately to the electricity supply, both for safetly
reasons and for easy removal of the oven for repair,
maintenance etc.
Use a rubber cable of the type H05RR-F with a
suitable cross section 3 x 0.75 mm².
The yellow-green earth wire must be 2-3 cm longer
than the other wires.
DO NOT use adapters as they could cause
overheating or burning.
Before connecting to the power supply, make sure
that:
• the limiter switch and the domestic system can
withstand the load from the appliance (see rating
plate).
• the supply system is efficiently earthed according
to standards and laws in force.
• the socket or double-pole switch are easily
accessible when the appliance is installed.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
7
Description of the
appliance
Overall view
GB
GAS BURNERS
Support Grid for
COOKWARE
Control Knobs for
GAS BURNERS
Support Grid for
COOKWARE
GAS BURNERS
Control Knobs for
GAS BURNERS
SAFETY
DEVICES *
Ignition for
GAS BURNERS *
• GAS BURNERS differ in size and power. Use the
diameter of the cookware to choose the most
appropriate burner to cook with.
• GAS BURNER ignition* enables a specific burner
to be lit automatically.
• SAFETY DEVICE* stops the gas flow if the flame
• Control Knobs for GAS BURNERS adjust the size
is accidentally extinguished.
of the flame.
Only available on certain models.
*
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
8
Start-up and use
! The position of the corresponding gas burner or
To turn on one of the rings, press the relative knob in
all the way and turn it anti-clockwise to the high
GB
electric hotplate* is shown on every knob.
setting
. The burner is fitted with an electronic
Gas burners
igniter that automatically starts when the knob is
pressed in.
Each burner can be adjusted to one of the following
settings using the corresponding control knob:
Since the burner is equipped with a safety
device, after lighting the burner keep the knob
pressed in for about 2-3 seconds to allow the device
which keeps the flame lit automatically to heat up.
The selected burner can be regulated using the
corresponding knob, as follows:
•
Off
Maximum
Minimum
•
Off
To light one of the burners, hold a lit match or lighter
near the burner and, at the same time, press down
and turn the corresponding knob anti-clockwise to the
maximum setting.
Maximum
Minimum
Since the burner is fitted with a safety device, the
knob should be pressed for approximately 2-3
seconds to allow the automatic device keeping the
flame alight to heat up.
To switch off the burner, turn the knob in a clockwise
direction until it stops (when reaches the “•” position).
Practical advice on using the burners
When using models with an ignition button, light the
desired burner pressing down the corresponding
knob as far as possible and turning it anticlockwise
towards the maximum setting.
To ensure the burners operate efficiently:
• Use appropriate cookware for each burner (see
table) so that the flames do not extend beyond
the bottom of the cookware.
! If a flame is accidentally extinguished, turn off the
control knob and wait for at least 1 minute before
trying to relight it.
• Always use cookware with a flat base and a cover.
• When the contents of the pan reach boiling point,
turn the knob to minimum.
To switch off the burner, turn the knob in a clockwise
direction until it stops (when reaches the “•” position).
Burner
Ø Cookware Diameter (cm)
Rapid (R)
24 - 26
16 - 20
10 - 14
The “separate double flame” burner*
Semi-Rapid (S)
This burner consists of two concentric burners which
can operate either together or separately.
Use of the double flame on the maximum setting
gives a very high power which reduces cooking
times with respect to conventional burners.
Moreover the double flame crown provides a more
uniform distribution of heat on the bottom of the pan,
when using both burners on minimum.
Auxiliary (A)
Pans to be used on 60 cm hobs
Burner
Ø Cookware Diameter (cm)
Reduced Rapid (RR)
Semi-Rapid (S)
24 - 26
16 - 20
10 - 14
16 - 20
24 - 26
24 - 26
10 - 14
26 - 28
To ensure that the double-flame burner is
used to its full potential, never set the inside
ring to minimum and the outside ring to
maximum at the same time.
Auxiliary (A)
Semi-Fishburner (SP)
Triple Crown (TC)
Pots and pans of all sizes can be used. In the case
of the smaller pots and pans we recommend the use
of only the internal burner.
Ultra Rapid (UR)
Double Flame (DCDR internal)
Double Flame (DCDR external)
Pans to be used on 75 cm hobs
There is a separate control knob for each of the
“separate double flame” burners.
The knob marked by the symbol
external burner;
operates the
The knob marked by the symbol
internal burner.
operates the
Only available on certain models.
*
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
9
! On the models supplied with a reducer shelf,
remember that this should be used only for the
Double flame internal (DCDR internal) burner when
you use casserole dishes with a diameter under 12
cm.
In addition, the two burners can be used in tandem
or speartely with cookware of different shapes and
sizes:
GB
• Double burner for a fish-kettle or oval cookware
(Fig.A).
To identify the type of burner, refer to the designs in
the section entitled, "Burner and Nozzle
Specifications".
• Double burner for a griddle or rectangular/square
cookware with minimum dimensions of 28x28 cm
(Fig.B)
• Single burner for medium size cookware (diameter
of 16-20 cm) (Fig.C).
Practical Advice on Using the Half Fish-Kettle
Burner *
• NEVER use the double burner in the
configuration represented in figure D.
The two "Half Fish-Kettle" burners, are eliptic in form
and can be turned up to 90°. This makes the
cooktop more flexible in terms of how it can be
used.
Fig. A
Fig. B
To turn the two burners 90°, proceed as follows:
• Make sure that the burners are cool;
• Lift the burner completely out of its housing;
• Replace it in its housing in the position desired;
• Make sure that the burners are positioned
correctly before use.
Fig. C
Fig. D
Only available on certain models.
*
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
10
Precautions and tips
! This appliance has been designed and manufactured
in compliance with international safety standards. The
following warnings are provided for safety reasons and
must be read carefully.
• Do not use unstable or deformed pans.
• Remove any liquid from the lid before
opening it.
GB
• The appliance should not be operated by people
(including children) with reduced physical, sensory or
mental capacities, by inexperienced individuals or by
anyone who is not familiar with the product. These
individuals should, at the very least, be supervised
by someone who assumes responsibility for their
safety or receive preliminary instructions relating to
the operation of the appliance.
General safety
• This is a class 3 built-in appliance.
• Gas appliances require regular air exchange to
maintain efficient operation. When installing the
hob, follow the instructions provided in the
paragraph on “Positioning” the appliance.
• These instructions are only valid for the countries
whose symbols appear in the manual and on the
serial number plate.
• Do not let children play with the appliance.
• The appliance is not intended to be operated by
means of an external timer or separate remote-
control system.
• The appliance was designed for domestic use inside
the home and is not intended for commercial or
industrial use.
Disposal
• The appliance must not be installed outdoors, even in
covered areas. It is extremely dangerous to leave the
appliance exposed to rain and storms.
• When disposing of packaging material: observe local
legislation so that the packaging may be reused.
• The European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment (WEEE), requires
that old household electrical appliances must not be
disposed of in the normal unsorted municipal waste
stream. Old appliances must be collected separately
in order to optimise the recovery and recycling of the
materials they contain and reduce the impact on
human health and the environment. The crossed out
“wheeled bin” symbol on the product reminds you of
your obligation, that when you dispose of the
• Do not touch the appliance with bare feet or with wet
or damp hands and feet.
• The appliance must be used by adults only for the
preparation of food, in accordance with the
instructions outlined in this booklet. Any other
use of the appliance (e.g. for heating the room)
constitutes improper use and is dangerous. The
manufacturer may not be held liable for any
damage resulting from improper, incorrect and
unreasonable use of the appliance.
appliance it must be separately collected.
• Ensure that the power supply cables of other
electrical appliances do not come into contact with
the hot parts of the oven.
Consumers may take their old appliance to public
waste collection areas, other communal collection
areas, or if national legislation allows return it to a
retailer when purchasing a similar new product.
All major household appliance manufacturers are
active in the creation of systems to manage the
collection and disposal of old appliances.
• The openings used for ventilation and dispersion of
heat must never be covered.
• Always make sure the knobs are in the “ꢀ”/“ꢀ”
position when the appliance is not in use.
• When unplugging the appliance always pull the plug
from the mains socket, do not pull on the cable.
• Never carry out any cleaning or maintenance work
without having detached the plug from the mains.
• In case of malfunction, under no circumstances
should you attempt to repair the appliance yourself.
Repairs carried out by inexperienced persons may
cause injury or further malfunctioning of the
appliance. Contact a Service Centre (see
Assistance).
Recycling & Disposal Information
As part of Hotpoint's continued commitment to helping
the environment, Hotpoint reserves the right to use
quality recycled components to keep down customer
costs and minimise material wastage.
Please dispose of packaging and old appliances
carefully.
• Always make sure that pan handles are turned
towards the centre of the hob in order to avoid
accidental burns.
To minimise risk of injury to children, remove the door,
plug and cut mains cable off flush with the appliance.
Dispose of these parts separately to ensure that the
appliance can no longer be plugged into a mains
socket, and the door cannot be locked shut.
• Do not close the glass cover (if present) when the gas
burners are still hot.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
11
Maintenance and care
Switching the appliance off
Gas tap maintenance
GB
Disconnect your appliance from the electricity
supply before carrying out any work on it.
Over time, the taps may become jammed or difficult
to turn. If this happens, the tap must be replaced.
! This procedure must be performed by a
qualified technician authorised by the
manufacturer.
Cleaning the appliance
! Do not use abrasive or corrosive detergents such
as stain removers, anti-rust products, powder
detergents or sponges with abrasive surfaces: these
may scratch the surface beyond repair.
! Never use steam cleaners or pressure cleaners on
the appliance.
• It is usually enough to wash the hob with a damp
sponge and dry it with absorbent kitchen roll.
• The removable parts of the burners should be
washed frequently with warm water and soap and
any burnt-on substances removed.
• For hobs which ligth automatically, the terminal
part of the electronic instant lighting devices
should be cleaned frequently and the gas outlet
holes should be checked for blockages.
• Stainless steel can be marked by hard water that
has been left on the surface for a long time, or by
aggressive detergents containing phosphorus.
After cleaning, rinse and dry any remaining drops
of water.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
12
Troubleshooting
It may happen that the appliance does not function properly or at all. Before calling the service centre for
assistance, check if anything can be done. First, check to see that there are no interruptions in the gas and
electrical supplies, and, in particular, that the gas valves for the mains are open.
GB
Problem
Possible causes/Solution
The burner does not light or the flame is not
even around the burner.
• The gas holes on the burner are clogged.
• All the movable parts that make up the burner are
mounted correctly.
• There are draughts near the appliance.
The flame dies in models with a safety device.
• You pressed the knob all the way in.
• You keep the knob pressed in long enough to activate the
safety device.
• The gas holes are not blocked in the area corresponding
to the safety device.
The burner does not remain lit when set to
minimum.
• The gas holes are not blocked.
• There are no draughts near the appliance.
• The minimum setting has been adjusted properly.
The cookware is unstable.
• The bottom of the cookware is perfectly flat.
• The cookware is positioned correctly at the centre of the
burner.
• The pan support grids have been positioned correctly.
If, despite all these checks, the hob does not function properly and the problem persists, call the nearest
Customer Service Centre. Please have the following information handy:
• The appliance model (Mod.).
• The serial number (S/N).
This information can be found on the data plate located on the appliance and/or on the packaging.
! Never use unauthorised technicians and never accept replacement parts which are not original.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
13
Guarantee
12 months Parts and Labour Guarantee
Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of breakdown repairs for
twelve months from the date of purchase.
This gives you the reassurance that if, within that time, your appliance is proven to be defective because of
either workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost to
you.
This guarantee is subject to the following conditions:
- The appliance has been installed and operated correctly and in accordance with our operating and
maintenance instructions.
-
-
-
The appliance is used only on the electricity or gas supply printed on the rating plate.
The appliance has been used for normal domestic purposes only.
The appliance has not been altered, serviced, maintained, dismantled, or otherwise interfered with by any
person not authorised by us.
-
-
-
Any repair work must be undertaken by us or our appointed agent.
Any parts removed during repair work or any appliance that is replaced become our property.
The appliance is used in the United Kingdom or Republic of Ireland.
The guarantee does not cover:
- Damage resulting from transportation, improper use, neglect or interference or as a result of improper
installation.
- Replacement of any consumable item or accessory. These included but not limited to: plugs, cables,
batteries, light bulbs, fluorescent tubes and starters, covers and filters.
-
Replacement of any removable parts made of glass or plastic.
THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL OR NON-
DOMESTIC PREMISES.
5 Year Parts Guarantee
Hotpoint also offers you a free 5 year parts guarantee. This additional guarantee is conditional on you registering
your appliance with us and the parts being fitted by one of our authorised engineers. There will be a charge for
our engineer’s time. To activate the extra parts warranty on your appliance, simply call our registration line on
08448 24 24 24 (Republic of Ireland 01 230 0800)
Extended Guarantees
We offer a selection of protection plans that enable you to fully cover yourself against the expense of repair bills
for the life of your policy. To find the ideal plan for you please call our advice line on 08448 226 226 (Republic
of Ireland 01 230 0233).
Free Helpdesk Service
We have a dedicated team who can provide free advice and assistance with your appliance if you experience
any technical difficulties within the first 90 days of ownership. Simply call our Hotpoint Service Hotline on 08448
224 224 (Republic of Ireland 0818 313 413) for telephone assistance, or, where necessary, to arrange for an
engineer to call.
After Sales Service
No one is better placed to care for your Hotpoint appliance during the course of its working life than us – the
manufacturer.
Essential Contact Information
Hotpoint Service
We are the largest service team in the country offering you access to 400 skilled telephone advisors and 1000
fully qualified engineers on call to ensure you receive fast, reliable, local service.
UK: 08448 224 224
Republic of Ireland: 0818 313 413
Please note: Our advisors will require the following information:
Model number:
Serial number:
Parts and Accessories
We supply a full range of genuine replacement parts as well as accessory products that protect and
hygienically clean your appliance to keep it looking good and functioning efficiently throughout its life.
UK: 08448 225 225
Republic of Ireland: 0818 313 413
Appliance Registration
We want to give you additional benefits of Hotpoint ownership. To activate your free 5 year parts guarantee you
must register your appliance with us.
UK: 08448 24 24 24
Republic of Ireland: 01 230 0800
Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB
Indesit Company Unit 49 Airways Industrial Estate, Dublin 17
Recycling and Disposal Information
As part of Hotpoint’s continued commitment to helping the environment, Hotpoint reserves the right to use
quality, recycled components to keep down customer costs and minimise material wastage.
Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children, remove the
door, plug, and cut the mains cable off flush with the appliance. Dispose of these parts separately to ensure
that the appliance can no longer be plugged into mains socket, and the door cannot be locked shut.
03/2012 - 195097584.02
XEROX FABRIANO
GB
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
16
|