Instructions for Installation and Use
60cm Dual Fuel Cooker
EG74
To the Installer:
Before installation, fill in the product details on the back cover of this book.
The information can be found on the rating plate.
To the User:
You must read the instructions prior to installing and using the appliance and
then retain them for future reference.
Introduction
To help you make the best use of your cooker, PLEASE READ THIS BOOKLET
CAREFULLY.
Your new cooker is guaranteed and will give lasting service.
The guarantee is only applicable if the cooker has been installed in accordance
with the Installation Instructions.
The cooker is designed specifically for domestic use and responsibility will not
be accepted for use in any other installation.
When first using the cooker ensure that the room is well ventilated (e.g. open a
window or use an extractor fan) and that persons who may be sensitive to the
odour avoid any fumes. It is suggested that any pets be removed from the room
until the smell has ceased. This odour is due to any temporary finish and also
any moisture absorbed by the insulation.
Our policy is one of continual improvement in design and development,
therefore strict accuracy of illustrations and descriptions cannot be
guaranteed.
This appliance conforms to the following EEC Directive:
Gas Appliances
90/396/EEC
Low Voltage Equipment
73/23/EEC
93/68/EEC
Electromagnetic Compatibility
89/336/EEC
92/31/EEC
93/68/EEC
3
For your Safety
Please read the precautions below before using your cooker.
ALWAYS . . .
ALWAYS make sure you understand the controls before using the cooker.
ALWAYS check that all controls on the cooker are turned off after use.
ALWAYS stand back when opening an oven door to allow heat to disperse.
ALWAYS use dry, good quality oven gloves when removing items from the ovens.
ALWAYS take care when removing items from the top oven/grill when the main
oven is on, as the contents may be hot.
ALWAYS keep the oven and grill doors closed when the cooker is not in use.
ALWAYS place pans centrally over the hotplate burners and position them so
that the handles cannot accidentally be caught or knocked or become
heated by other burners.
ALWAYS keep the cooker clean, as a build up of grease or fat from cooking can
cause a fire.
ALWAYS allow the cooker to cool before cleaning.
ALWAYS follow the basic principles of food handling and hygiene to prevent the
possibility of bacterial growth.
ALWAYS keep ventilation slots clear of obstructions.
ALWAYS turn off the electricity supply before cleaning or replacing an oven
lamp.
ALWAYS refer servicing to CORGI registered appliance service engineers.
4
For your Safety
NEVER . . .
NEVER leave children unsupervised where the cooker is installed as all
surfaces will get hot during and after use.
NEVER allow anyone to sit or stand on any part of the cooker.
NEVER store items that children may attempt to reach above the cooker.
NEVER heat up unopened food containers as pressure can build up causing the
container to burst.
NEVER store chemicals, food stuffs, pressurised containers in or on the
cooker, or in cabinets immediately above or next to the cooker.
1
3
NEVER fill a deep fat frying pan more than / full of oil, and never use a lid.
DO NOT LEAVE UNATTENDED WHILE COOKING.
NEVER place flammable or plastic items on or near the hotplate.
NEVER use proprietary spillage collectors on the hotplate.
NEVER use the cooker as a room heater.
NEVER dry clothes or place other times over or near to the hotplate or
oven/grill doors.
NEVER wear garments with long flowing sleeves whilst cooking.
NOTE: The use of a gas cooking appliance results in the production of heat and
moisture in the room in which it is installed. Always ensure that the kitchen is
well ventilated; keep natural ventilation holes open or install a mechanical
ventilation device (mechanical extractor hood).
In particular when using more than one hotplate burner, open a window if a
mechanical ventilation device is not operating.
5
Oven Timer Operation
The oven timer offers you the following features:
1. Time of Day
2. Automatic Cooking
3. Minute Minder
AUTOMATIC COOKING
The main oven can be controlled automatically.
GUIDANCE ON AUTOMATIC COOKING
1. Select foods which will take the same time to cook.
2. Set the oven timer so that the food has just finished or is just about to
finish cooking on your return to the oven. This will ensure the food has not
cooled down and does not require reheating before serving.
3. Food should be as cold as possible when it goes into the oven, ideally
straight from the refrigerator. Frozen meat and poultry should be thawed
thoroughly before it is put in the oven.
4. Warm food should never be placed in the oven if there is to be a delay period.
Stews prepared by frying the meat and vegetables should be cooked as soon
as possible.
5. Dishes containing left-over cooked poultry or meat, for example Shepherds
Pie, should not be cooked automatically if there is to be a delay period.
6. Stews and joints should be cooked by the long slow method, so that the delay
period is kept to a minimum.
7. On warm days, to prevent harmful bacterial growth in certain foods (ie poultry,
joints, etc) the delayed start should be kept to a minimum.
8. Wine or beer may ferment and cream may curdle during the delay period, so
it is best to add these ingredients just before serving.
9. Foods which discolour should be protected by coating in fat or tossing in
water to which lemon juice has been added, prior to placing food in the oven.
10. Dishes containing liquid should not be filled too full to prevent boiling over.
11. Food should be well sealed (but not airtight) in a container to prevent the
loss of liquid during cooking. Aluminium foil gives a good seal.
12. Ensure food is cooked thoroughly before serving.
6
Oven Timer Operation
CLOCKFACE
The timer incorporates a 24 hour clock.
Ensure the correct time of day is always set, before using your cooker.
SYMBOLS
A ‘bell’ symbol will light up when you select a Minute Minder Period and will
remain lit for the period set.
At the end of the Minute Minder Period, the timer will emit an audible tone
and the ‘bell’ symbol will disappear.
The ‘cookpot’ symbol will light up either:–
–
–
When the timer is in manual mode, or
During the actual Cook Period.
‘AUTO’ will light up:–
–
When the timer is first turned on it will flash. It will go out when a time
of day is set or when the timer is set to manual.
The ‘AUTO’ symbol will flash at the end of an Auto Cooking programme to
indicate that the programme has finished.
(When the ‘AUTO’ symbol is flashing, to return the oven to Manual operation,
turn the oven controls off, ensure that the correct time of day is set, and
press the “Manual” button – The ‘AUTO’ symbol will go out).
TIMER FUNCTION BUTTONS
Minute Minder
Button
Here you can set a time period of up to 23 hours 59 minutes, that will count
down. When it reaches zero, the timer will emit an audible tone.
For Example: If you set 20 minutes, the audible tone will occur 20 minutes later.
AUTO COOKING PROGRAMME
Cook Period Button Cook Period is the actual length of time for which, the timer will switch the
oven(s) on as part of an “Auto Cooking” programme.
(e.g. If you set 2 hours, the food will be cooked for 2 hours).
End Time Button
The time of day at which you want an “Auto Cooking” programme to end.
For Example: If you set a “Cook Period” for 2 hours, and “End Time” of 11:00.
The timer will switch the oven(s) on at 9:00 and turn the oven(s) off at 11:00.
You will hear a audible tone at 11:00, to indicate that the Auto Cooking
Programme has finished.
Notes:
-
When setting an Auto Cooking programme you will need to set the oven
control(s) to the required temperature(s) when you set the timer.
If an Auto Cooking programme has been set the oven(s) will only operate
during the pre-programmed time.
-
Manual Button
Needs to be pressed to cancel an Auto Cooking programme and return the
oven(s) to Manual operation.
“+” and “–” Buttons Used to adjust the various timer function settings.
7
Oven Timer Operation
SETTING THE TIME OF DAY
Step 1 Make sure all oven controls are turned Off.
Step 2 Check the electricity supply to the cooker is turned on.
Step 3 When switched on the display will show 0.00 and the Auto symbol,
flashing intermittently.
Step 4 Press and hold in both the Cook Period & End Time buttons together.
Step 5 With the Cook Period & End Time buttons still held in, press either
the “+” or “–” buttons to set the correct time of day.
Step 6 Release all the buttons simultaneously.
THE TIME OF DAY IS NOW SET.
To change the time of day repeat Steps 4, 5 & 6 above.
Note: You cannot adjust the time of day if the timer has been set for an
Auto Cooking Programme.
SETTING THE MINUTE MINDER
Step 1 Ensure the time of day is set correctly.
Step 2 Press and hold the Minute Minder button.
Step 3 With the Minute Minder button held in, set the required Minute Minder
period using the “+” and “–” buttons. A ‘bell’ symbol will light up.
Release all buttons and the timer display will revert back to the time of day.
The ‘bell’ symbol will remain lit to signify that a Minute Minder period has
been set.
At the end of the set time an audible tone will be heard, and the ‘bell’
symbol will disappear.
Step 4 To cancel the audible tone press the Minute Minder button.
Note 1 When the Minute Minder has been set, the time remaining can be checked at
any time by simply pressing the Minute Minder button.
Note 2 If necessary the Minute Minder can be cancelled before the tone sounds by
pressing and holding the Minute Minder button and then at the same time
pressing the “–” button until 0.00 appears in the display window.
8
Oven Timer Operation
AUTO COOKING PROGRAMMES
There are two Auto Cooking programmes that can be selected using your timer:–
(a) To set the timer to switch the oven(s) On and Off Automatically
(b) To set timer to switch on immediately and OFF automatically after a set cook period.
a) TO SET THE TIMER TO SWITCH THE OVEN(S) ON AND OFF AUTOMATICALLY
This allows you to cook at a specified time for a chosen period before the oven switches
off Automatically.
Step 1 Check that the correct time of day is set, if not follow instructions for setting the
time of day.
Step 2 Place food onto the correct shelf position in the oven and close the oven door(s).
Step 3 Press and hold in the Cook Period button.
The display will read 0.00 with the ‘cookpot’ symbol lit.
Step 4 With the Cook Period button still held in, set the required Cook
Period using the “+” and “–” buttons.
Release the buttons and the timer display will revert to the time of day with
the ‘Auto’ symbol and ‘cookpot’ symbol lit.
Step 5 Press and hold in the End Time button.
The display will read the earliest possible end time for the Cook
Period that you have set above.
The ‘Auto’ symbol and ‘cookpot’ symbol will be lit.
Step 6 With the End Time button still held in, use the “+” and “–” buttons to
set the ‘End Time’ (i.e. The time you require the oven to switch off).
Release all the buttons and the timer will revert back to the time of day.
The ‘Auto’ symbol will remain lit to signify that an Auto Cooking Programme
has been set. The ‘cookpot’ symbol will go out.
Step 7 Turn the oven control(s) to the required temperature, and if
necessary select the appropriate oven function.
At the end of the Automatic Cook Period the Auto Symbol will flash and an
intermittent bleeping sound will be heard.
The audible tone will continue unless cancelled.
The ‘Auto’ symbol will continue to flash until the timer is returned to Manual
operation (see below).
Step 8 Press the Manual button, the audible tone will be cancelled and the
oven(s) will be returned to Manual.
Step 9 Turn the oven control(s) to the OFF position.
9
Oven Timer Operation
Note 1 When cooking automatically the Cook Period can be checked at any time by
simply pressing the Cook Period button.
Note 2 When cooking automatically the End Time can be checked at any time by simply
pressing the End Time button.
b) TO SET TIMER TO SWITCH ON IMMEDIATELY AND OFF AUTOMATICALLY AFTER A SET
COOK PERIOD
Step 1 Check that the correct time of day is set, if not follow instructions for setting the time of
day.
Step 2 Place food onto the correct shelf position in the oven and close the oven door(s).
Step 3 Turn the oven control(s) to the required temperature, and if necessary select the
appropriate oven function.
Step 4 Press and hold in the Cook Period button, the display will read 0.00
and the ‘cookpot’ symbol will light up.
With the Cook Period button still held in set the required Cook Period using
the “+” and “–” buttons. Example: 1hr 30 minutes (as shown).
Note: Cook Period is the length of time the food requires to cook.
Step 5 Release all buttons.
The timer display will revert to the time of day with the ‘Auto’ symbol lit &
‘cookpot‘ symbol remaining lit.
At the end of the Cook Period the ‘Auto’ symbol will flash and an
intermittent audible tone will be heard.
NOTE: The Cookpot symbol disappears
The audible tone will continue until cancelled. The ‘Auto’ symbol will continue
to flash until the timer is returned to Manual operation (see below).
Step 6 Press the Manual button. The audible tone will be cancelled and the
oven(s) will be returned to Manual.
Step 7 Turn the oven control(s) to the OFF position.
10
Oven Timer Operation
TO CANCEL AN AUTO COOKING PROGRAMME BEFORE
THE COOK PERIOD HAS FINISHED.
Step 1 Turn the oven control(s) to the OFF position.
Step 2 Press the Manual button to return the oven(s) to “Manual”
operation.
The ‘Auto’ symbol will go out.
Note 1
When cooking automatically the Cook Period can be checked at any time by simply
pressing the Cook Period button.
OTHER NOTES ON TIMER OPERATION
1. When cooking Automatically the Cook Period can be checked at any time simply by pressing the
Cook Period button.
2. When cooking Automatically the End Time can be checked at any time by simply pressing the End
Time button.
3. Having set a Cook Period and End Time an electronic device stores the information. The device
within the timer will switch the oven(s) on and off at the required times.
4. When setting an Auto Cooking Programme and a mistake is made, to clear:–
(a) Press & release the Manual button.
(b) Start the sequence again.
5. If at any time the display shows three flashing zero’s 0.00 and ‘Auto’, it is likely that the electricity
supply to the oven has been interrupted. Reset the timer to the correct time of day.
Food in the oven may, therefore, not have been cooked, before serving check food is thoroughly
heated and completely cooked.
6. To set each function always press and hold the required function button and at the same time
press “+” or “–” buttons.
11
Hotplate
The hotplate lid is fitted with a safety device which cuts off the gas supply to
the hotplate burners unless the lid is fully open. Do not use the safety device as
a means of controlling the hotplate burners.
The hotplate has two high speed burners and two simmering burners which will
1
accommodate pans between 100mm (4”) and 240mm (9 /2”) diameter. All pans
should be positioned centrally over the burners.
TO USE THE HOTPLATE
1. Remove any items or spillage from the top of the lid and then raise it
to its fully open position.
2. Press the ignition button and then push in and turn the control knob
of the chosen burner anti-clockwise to the large flame symbol.
Continue to press the ignition button until the sparks light the gas.
3. Turn the control knob anti-clockwise to reduce the heat input.
Only turn the control knob between the large flame symbol and the
small flame symbol when adjusting the setting.
4. To turn off, turn the control knob fully clockwise to the symbol O.
DO NOT use the hotplate unless all pan supports are in position.
DO NOT use mis-shapen pans which may be unstable.
DO NOT use round base woks directly on the pan supports.
DO NOT use the glass lid as a working surface.
Each burner is fitted with a spark ignitor for lighting the gas. To ensure rapid
lighting of the burners every time they are used, the ignitors must be kept clean
and dry. Remove any food spillage or cleaning materials from the ignitor using a
small nylon brush such as a tooth brush. Access to the ignitor can be achieved by
lifting off the loose burner parts carefully when the burners are cool.
When the hotplate burner bodies and caps are removed for cleaning, be careful
not to drop any food particles or cleaning materials into the burner bases, to
avoid the possibility of blocking the gas jets.
If aluminium based pans are used, a silvery deposit may appear on the top
edge of the pan support fingers. See ‘Care and Cleaning’ section for cleaning
information.
12
Hotplate
SAFETY REQUIREMENTS FOR DEEP FAT FRYING
1. Never fill chip pans more than one third full with oil or fat.
2. Never leave oil or fat unattended during the heating or cooling period.
3. Never heat fat or fry with a lid on the pan.
4. Always dry food thoroughly before frying, and lower it slowly into the
hot oil or fat. Frozen foods in particular will cause frothing and
spitting if added too quickly.
5. Always keep the outside of the pan clean and free from streaks of oil
or fat.
HOW TO DEAL WITH A FAT FIRE
1. Do not move the pan.
2. Turn off the hotplate burners.
3. Smother the flames with a fire blanket or damp cloth to extinguish
the fire.
Do not use water or a fire extinguisher as the force of it may spread
the burning fat or oil over the edge of the pan.
4. Leave the pan for at least 60 minutes before moving it.
13
Grill
CAUTION – ACCESSIBLE PARTS MAY BECOME HOT WHEN THE GRILL IS IN USE.
YOUNG CHILDREN SHOULD BE KEPT AWAY.
GRILLING SHOULD NEVER BE UNDERTAKEN WITH THE GRILL DOOR CLOSED.
The grill control is designed to provide variable heat control of either the full
width of the grill or just the left half. Turning the control knob clockwise will
switch on the full width and turning anti-clockwise will switch on just the left half.
A gentle flow of air will be blown from underneath the control panel when the grill
is in use.
GRILL PAN HANDLE
The grill pan handle is detachable from the pan to facilitate cleaning. The handle
can be either detachable from or fixed to the pan.
Remove the screw and washer from the grill pan bracket, tilt the handle over the
recess adjacent to the bracket (A). Slide the handle toward the centre of the pan
(B) and let the handle locate over the bracket (C).
For a detachable handle: Remove the screw and washer from the grill pan and
keep safe.
For a fixed handle: Replace the screw and washer and ensure they are fully tightened.
Warning: Ensure when using grill pan handle in the detachable manner it is
centralised and secure.
C
A
B
TO USE THE GRILL
1. Open the grill/top oven door and place the shelf in the required position.
2. Turn the grill control knob clockwise to 4 (max) for full width grilling or
anticlockwise for the half grill.
3. Slide the grill pan toward the back of the grill compartment until it stops.
4. Leave the control at 4 (max) for toast and for sealing and fast cooking of
foods. For thicker foods requiring longer cooking, turn the control to a
lower setting after sealing on both sides at 4 (max).
NOTE: The grill will not operate unless the top oven control is in the OFF position.
Grilling can be started from cold but for best results preheat for approximately 5
minutes.
DO NOT cover the grill pan or grid with aluminium foil as this can hold fat,
intensify the heat and cause a fire hazard.
14
Ovens
Both ovens have a thermostat light that will illuminate until the oven has reached
the set temperature. It will then switch off and on during cooking as the thermostat
maintains the temperature.
Each shelf has a safety stop to prevent it from being pulled out too far when
attending to food. Shelves are removed by pulling them out to the stop and then
lifting at the front to withdraw. The oven cooking charts are a guide only, giving
approximate cooking temperatures and times. To suit personal taste and
requirements it may be necessary to increase or decrease temperatures by 10˚C.
After the ovens have been operating for a short period, a gentle flow of air will
be blown from underneath the control panel which may continue for a while after
the controls have been turned off.
TOP OVEN - CONVENTIONAL COOKING
The top oven can be used to cook small quantities of food or used in conjunction
with the main oven to provide additional cooking space.
TO USE THE TOP OVEN
1. Place oven shelf in chosen position (refer to cooking chart).
2. Turn the top oven control knob clockwise to the required setting. The top
oven thermostat light will go off when the oven has reached the set
temperature.
Food should be placed in the centre of the shelf with a gap of at least 25mm
(1 inch) between it and the grill element to avoid burning and ensuring an even
cooking.
Do not place food or dishes on the floor of the oven.
MAIN OVEN - FAN COOKING
Fan cooking is ideal for large poultry or joints of meat, reducing cooking times
and often eliminating the need for preheating the oven. It is also ideal for batch
cooking where food is cooked on more than one level, because the forced
circulation of hot air gives an even temperature from the top to the bottom of
the oven.
When cooking recipes that are not designed for a fan oven, it is recommended
that the temperature is reduced by about 25˚C and the time reduced by about
10 minutes for each hour. If a large quantity of food is being cooked, it will be
necessary to increase the cooking time to compensate for the extra oven load.
TO USE THE MAIN OVEN
1. Check that the timer is set to manual.
2. Place oven shelves in chosen position (refer to cooking chart).
3. Turn the main oven control knob clockwise to the required setting. Pre-
heating is not normally necessary, but some foods such as bread, scones
and Yorkshire pudding do benefit from being placed in a hot oven.
Food should be placed in the centre of each shelf to allow for even air circulation
around the food.
15
Oven Cooking Charts
Note: If soft margarine is used for cake making, temperatures recommended by the manufacturers should be
followed. Temperatures recommended in this chart refer to cakes made with block margarine only.
16
17
The Slow Cook Setting
The ‘S’ setting on the main oven thermostat is used for slow cooking, keeping food
warm and warming plates for short periods.
USING THE ‘S’ SETTING FOR SLOW COOKING
1. All dishes cooked by the ‘S’ setting should be cooked for a minimum 6 hours.
They will ‘hold’ at this setting for a further hour but marked deterioration in
appearance will be noticed in some cases.
2. Joints of meat and poultry should be cooked at Mk. 6 for 30 minutes before
turning to the ‘S’ setting and never be cooked lower than the middle shelf
position.
3. Joints of meat over 6 lbs (2.7kg) and poultry over 4 lbs 8oz (2 kg) should not be
cooked using the ‘S’ setting.
4. Always stand covered joints on a rack over the meat tin to allow good air
circulation.
5. A meat thermometer should be used when cooking pork joints and poultry.
The internal temperature of the food should reach at least 88˚C.
6. This method is unsuitable for stuffed meat and stuffed poultry.
7. Always bring soups, casseroles and liquids to the boil before putting in the
oven.
8. Cover casseroles with foil and then the lid to prevent loss of moisture.
9. Always thaw frozen food completely before cooking.
10. Root vegetables will cook better if cut into small pieces.
11. Adjust seasonings and thickenings at the end of the cooking time.
12. Use the zones of heat in the oven, e.g. meringues and milk puddings can be
cooked lower in the oven whilst other dishes requiring greater heat can be
cooked above them.
13. Egg and fish dishes need only 1-5 hours cooking and should be included in day
cooking sessions, when they can be observed from time to time.
14. Dried red kidney beans must be boiled for a minimum of ten minutes after
soaking, before inclusion in any dish.
18
Care and Cleaning
Switch off the electricity supply and allow to cool before cleaning the cooker.
Clean the cooker regularly and wipe up spills soon after they occur to prevent
them from becoming burnt on. Never use biological washing powder, caustic
cleaners, harsh abrasives, scouring pads, steam cleaners, aerosol cleaners or
oven chemical cleaners of any kind.
If it is necessary to remove the cooker for cleaning, ensure that it is cool and
beware that it is heavy (approximately 70 kg 155 lbs). To move the cooker
forward, open the top oven/grill door and with both hands positioned under the
roof of the compartment, lift and pull forward. Replace by pushing the cooker
backwards. Check that the cooker is level. Take care not to damage any floor
coverings.
OVEN HEAT CLEAN LININGS
The oven side linings are coated with a special enamel which has a continuous
cleaning action. The higher the oven temperature the more effective the action.
In most cases this cleaning operation will proceed during normal cooking.
However, if roasting is done frequently, or high temperatures are not used
regularly, it may be necessary to occasionally operate the oven empty at the
maximum setting for about an hour.
It should not normally be necessary to clean the linings with water, but if
desired, wipe them over with a soapy cloth, followed by a wipe with a damp clean
cloth.
OVEN DOORS
The door inner glass panels can be removed for ease of cleaning by simply
sliding the panels out of the frame.
REPLACEMENT OF OVEN LIGHT BULB
CAUTION: DISCONNECT THE APPLIANCE FROM THE ELECTRICITY SUPPLY BEFORE
REPLACING THE LIGHT BULB TO AVOID THE POSSIBILITY OF AN ELECTRIC SHOCK.
Light bulbs are not covered by the manufacturer’s guarantee.
A new 25W, 300˚C rated SES bulb can be obtained from your cooker supplier or
any major electrical retailer.
1.
Remove the shelves from the oven.
2.
Unscrew the lens using a thick cloth to protect your fingers in the unlikely
event of a lens fracture.
3. Unscrew bulb.
4. Fit new bulb and refit lens.
19
Care and Cleaning
COOKER FINISH
CLEANING METHOD
Cloth wrung out in warm soapy water. Stubborn
stains can be removed with a cream paste,
liquid cleaner or by rubbing with fine steel wool
soap pads.
Check that the cleaning agent is approved by
the Vitreous Enamel Association.
Vitreous Enamel
Hotplate, pan supports,
burner caps, roasting dish,
grill pan, main oven base,
inside of grill compartment
Wash with a cloth wrung out in warm soapy
water only.
DO NOT USE ABRASIVES.
Paint
Control panel trim,
side panels, doors trims.
Similar to paint cleaning above. Use a nylon
brush to remove any cleaning materials, water
or dirt from the hotplate burner bodies.
Aluminium
Hotplate burner bodies, lid
rear trim.
Glass
As for enamel cleaning. Polish with a clean dry
cloth or kitchen roll.
Wipe with a cloth wrung out in warm soapy
water.
A fine steel wool soap pad e.g. Brillo, Ajax, or a
chrome or stainless steel cleaner may be used.
Chromium Plating
Oven shelves, grill pan grid,
grill pan handle support
Plastic
Grill pan handle, control
knobs
Wipe with a cloth wrung out in warm soapy
water.
Wipe with a cloth wrung out in warm soapy
water. Polish with a clean dry cloth or kitchen
towel. For stubborn stains, use a proprietary
stainless steel cleaner and follow the
instructions on the container.
Stainless Steel
20
Something Wrong with your Cooker
Before contacting your Service Centre or Installer, check the problem guide
below, there may be nothing wrong with your cooker.
PROBLEM
CHECK
If all burners fail to ignite:
Check that sparks appear at the burners; a
clicking noise should be heard.
If not;
Burner will not light:
Check that the electricity supply is turned on.
If the electricity supply has failed, the hotplate
burners can be lit by a match.
If only one burner fails to ignite:
Hotplate burner
Check that the burner is dry and that spillage of
food or cleaning fluid remains are not affecting
the ignitor or burner ports.
Clean away any debris with a dry nylon brush such
as an old toothbrush. If a wire wool pad has been
used for cleaning around the burner ensure the
ignitor is free from any stray strands. Any water
on the burner should be dried with a cloth or
kitchen towel.
Ignitor
Burner ports
Make sure that all the burner parts are correctly
seated.
21
Something Wrong with your Cooker
PROBLEM
CHECK
Slight odour or small
amount of smoke when
grill / oven used first
time.
This is normal and should cease after a short period.
Check that the oven temperature and shelf positions are
as recommended in the Oven Cooking Charts. However,
it may be necessary to increase or decrease the
recommended setting slightly to suit your taste.
Oven cooks too fast or
too slow.
Cannot set an “Auto Cook” Read the Timer instructions in this book carefully
programme or cannot get remembering that the Cook period is the length of time
the timer to turn the oven that the timer will switch the oven(s) on as part of an
on or off at the required
times.
Auto Cooking Programme.
The electricity supply to the cooker may have been been
interrupted, but has now come back on again. set the
correct time of day by following the instructions given in
the timer section of this book.
Timer Display shows "0:00"
with "Auto" Flashing.
Main oven does not work,
but the grill, top oven and
hotplate burners work.
The timer may be set for an Auto Cooking Programme.
Check the timer to see if “AUTO” is illuminated. If it is,
follow the instructions given in the timer section of this
book to cancel the Auto Cooking Programme.
The oven lamp is not covered by the guarantee.
Oven lamp does not
work.
The part is easily changed (see the section on oven lamp
replacement). A new lamp may be obtained from our
Spare Parts department, see Key Contacts (back page).
Disposal of your product
To minimise the risk of injury to children please dispose of your product carefully and
safely. Remove all doors and lids. Remove the mains cable (where fitted) by cutting off
flush with the appliance and always ensure that no plug is left in a condition where it
could be connected to the electricity supply.
To help the environment, Local Authority instructions should be followed for the disposal
of your product.
Disposal of old electrical appliances
The European Directive 2002/96/EC on Waste Electrical and Electronic Equipment
(WEEE), requires that old household electrical appliances must not be disposed of in the
normal unsorted municipal waste stream. Old appliances must be collected separately in
order to optimise the recovery and recycling of the materials they contain and reduce
the impact on human health and the environment.
The crossed out “wheeled bin” symbol on the product reminds you of your
obligation, that when you dispose of the appliance it must be separately collected.
Consumers should contact their local authority or retailer for information
concerning the correct disposal of their old appliance.
22
Installation
Prior to installation, ensure that the local distribution conditions (nature of the
gas and gas pressure) and the adjustment conditions are compatible. The
adjustment conditions for this appliance are stated on the data badge which is
fitted on the back panel.
This appliance is not designed to be connected to a combustion products
evacuation device. It must be installed and connected in accordance with
current installation regulations. particular attention should be given to the
relevant requirements regarding ventilation.
MODEL NUMBERS EG74
Category II2H3+ (GB)
These models are set to burn NATURAL GAS (G20) at 20 mbar but can be
converted for use on BUTANE (G30) at 28-30mbar or PROPANE (G31) at 37mbar
with the use of the LPG conversion kit that can be obtained free of charge, if
you contact our Genuine Parts and Accessories department (see Key Contacts,
back page).
GAS SAFETY (INSTALLATION & USE) REGULATIONS
It is the law that all gas appliances are installed by competent persons in
accordance with the current edition of the above regulations. It is in your
interest and that of safety to ensure compliance with the law.
In the UK, CORGI registered installers work to safe standards of practice.
The cooker must also be installed in accordance with BS 6172.
Failure to install the cooker correctly could invalidate the warranty liability
claims and could lead to prosecution.
LOCATION
The cooker may be located in a kitchen, kitchen/diner or a bed-sitting room, but
not in a room containing a bath or shower. The cooker must not be installed in a
bed-sitting room of less than 20m3.
When adjusted for use on Butane (G30) or Propane (G31), the cooker must not
be installed in a room or internal space below ground level, e.g. in a basement.
PROVISION FOR VENTILATION
The room containing the cooker should have an air supply in accordance with
BS 5440: Part 2.
The room must have an opening window or equivalent; some rooms may also
require a permanent vent. If the room has a volume between 5 and 10m3, it will
require an air vent of 50cm2 effective area unless it has a door which opens
directly to outside. If the room has a volume of less than 5m3, it will require an
air vent of 100cm2 effective area. If there are other fuel burning appliances in
the same room, BS 5440: Part 2 should be consulted to determine air vent
requirements.
23
Installation
TECHNICAL DATA
1
1
2
2
Gas connection
Rp / ( / " BSP female)
Pressure test point
Gas rate adjustment
Aeration adjustment
Front left hotplate injector
None
None
Electrical connection
4mm2 twin and earth
230/240V a.c. 50Hz. 13A fuse.
G30 at 28-30mbar
G31 at 37mbar
G20 at 20mbar
HEAT
INPUT
HEAT
INPUT
INJECTOR
INJECTOR
BURNER
HOTPLATE
Front left and rear right
3.0 kW
116
103
3.0 kW (220g/h) 86
2.0 kW (145g/h) 70
HOTPLATE
2.0 kW
Front right and rear left
GRILL
2.4 / 2.7 kW
MAIN OVEN
TOP OVEN
1.8 / 2.0 kW
1.7 / 1.9 kW
24
Installation
SPACE FOR FIXING
The cooker can be close fitted below hotplate level. This requires a minimum
distance of 600mm between cupboard units of hotplate height.
When installing next to a tall cupboard, partition or wall, for a minimum distance
of 400mm above hotplate level, allow a side clearance of at least 65mm.
The diagram below illustrates the minimum clearance between the cooker and
adjacent walls, cupboards etc.
The wall behind the cooker, 50mm below and 450mm above, and the width of the
cooker, must be a non-combustible material such as ceramic wall tiles.
If the cooker is to be fitted close to a corner on the left hand side, ensure that
there is a clearance of at least 50mm to allow the main oven door to open fully
for when removing oven shelves.
65 mm Min
600 mm Min
COOKER HOODS
If a cooker hood is to be installed, refer to the cooker hood manufacturers’
instructions regarding fixing height.
25
Installation
UNPACKING THE COOKER
Unpack the components from inside the grill and oven: Check that the following
parts are present.
Grill pan and grid
Pan supports
Aluminium burner bodies( 4)
Main oven shelves (2)
Enamelled burner caps (4)
Literature
Top oven/grill shelf (1)
LEVELLING
Four skid feet are fitted which can be adjusted up or down to level the cooker.
CONVERSION FOR USE ON BUTANE (G30) OR PROPANE (G31)
Each burner requires the injector to be replaced and bypass screws adjusted or
replaced as follows:
1.
2.
Remove the loose hotplate burner parts.
Using a 7mm socket, replace the hotplate injectors as appropriate
(see table on previous page).
3.
4.
5.
Re-position the loose burner parts.
Carefully pull off the hotplate control knobs.
Using a narrow flat bladed screwdriver rotate the bypass screws fully
clockwise.The hotplate tap bypass screws are located down the centre of the
spindle.
6.
7.
Re-assemble the control panel parts.
Secure the self-adhesive LPG conversion label over the gas details on the data
badge.
26
Installation
STABILITY CHAIN
A hole in the gas inlet valve bracket can be used to engage a stability chain.
CONNECTING TO GAS SUPPLY
670
Connection to the cooker should be made with an approved appliance flexible
connection to BS 669. A length of 0.9 to 1.25m is recommended. The length of
hose chosen should be such that when the cooker is in situ, the hose does not
touch the floor.
Those cookers converted to use on LPG should be connected with a hose
suitable for LPG and capable of withstanding a pressure of 50 mbar.
An adaptor backplate should be fitted within the shaded area shown, to allow
the cooker to be pushed fully to the wall and to ensure that the flexible hose is
only likely to come into contact with areas at the rear of the cooker that do not
exceed a temperature rise of 70˚C.
27
Electrical Connection
Warning - THIS APPLIANCE MUST BE EARTHED
The cooker must be connected by a qualified electrician to a suitable double -
pole control unit with a minimum rating of 32A and a minimum contact clearance
of 3mm, which should be fitted adjacent to (but not above) the cooker, in
accordance with IEE regulations.
The power supply cable should conform to BS6004 with a conductor size of
4mm2.
The control unit should be easily accessible in the event of an emergency.
This appliance conforms to EN55014 regarding suppression of radio and
television interference.
The cooker terminals are behind the cover at the rear. The mains cable must
pass through the cable clamp and the screws must be fully tightened.
Sufficient cable should be used to allow the cooker to be pulled out for
servicing. Ensure that the cover is fully closed and secure afterwards.
Take care not to trap the mains cable when pushing the cooker into its final
position.
28
Installation
OPERATIONAL CHECKS
After installation, check for gas soundness. The supply pressure can be checked
at one of the hotplate burner injectors.
Check that the hotplate burners ignite correctly and burn with a steady flame.
Check for a steady flame at the low setting.
Instruct the user on operation of the cooker.
29
Key Contacts
After Sales Service
Over 1100 trained specialists, directly employed by us, ensure that you can have
complete confidence in both the appliances and services we offer.
Repair Service and Information Help Desk
UK: 08709 066 066
Monday to Friday, 8am to 7.30pm
Saturday, 8.30am to 5.30pm
Sunday, 9.30am to 3.30pm
Republic of Ireland: 0818 313 413
Note: Our operators will require the following information:
Model number
Serial number
Extended Warranties
UK: 08709 088 088
Monday to Sunday, 8am to 8pm
Republic of Ireland: 0123 002 333
Genuine Parts and Accessories
UK: 08709 077 077
Monday to Friday, 8.30am to 5pm
Saturday, 8.30am to 12noon
Republic of Ireland: 0818 313 413
Indesit Company UK Limited, Morley Way, Peterborough, PE2 9JB
.
PRINTED BY SIMLEX FOUR ASHES, WOLVERHAMPTON.
07/2006 Part no. 195057560.00
|