Operating Instructions
HOB
Contents
GB
Warnings, 2
Installation, 3-4
Positioning
Electrical connection
GB
English,1
Description of the appliance, 5
Control panel
Start-up and use, 6-9
Switching on the hob
Switching on the cooking zones
Booster function
Switching off the cooking zones
Programming the cooking duration
Timer
Control panel lock
Switching off the hob
“Demo” mode
CIC 642 C
CIA 641 C S
Practical advice on using the appliance
Safety devices
Practical cooking advice
Precautions and tips, 10
General safety
Disposal
Care and maintenance, 11
Switching the appliance off
Cleaning the appliance
Disassembling the hob
Technical description of the models, 11
After Sales Service, 12
Guarantee, 13
Installation
! Before operating your new appliance please read this
instruction booklet carefully. It contains important
information concerning the safe operation, installation
and maintenance of the appliance.
! Please keep these operating instructions for future
reference. Pass them on to any new owners of the
appliance.
GB
min. 20 mm
COMPARTMENT
Positioning
min. 40 mm
! Keep all packaging material out of the reach of
children. It may present a choking or suffocation
hazard (see Precautions and tips).
! The appliance must be installed by a qualified
professional in accordance with the instructions
provided. Incorrect installation may cause harm to
people and animals or may damage property.
min. 20 mm
FAN-ASSISTED
OVEN
Built-in appliance
Use a suitable cabinet to ensure that the appliance
functions properly.
• The supporting surface must be heat-resistant up to
a temperature of approximately 100°C.
• If the appliance is to be installed above an oven, the
oven must be equipped with a forced ventilation
cooling system.
min. 40 mm
• Avoid installing the hob above a dishwasher: if this
cannot be avoided, place a waterproof separation
device between the two appliances.
• Depending on the hob you want to install, the
cabinet must have the following dimensions (see
figure):
FRONT SIDE
OF HOB
SUPPORTING
SURFACE
UNDERSIDE
OF HOB
520
Ventilation
To allow adequate ventilation and to avoid overheating of
the surrounding surfaces the hob should be positioned as
follows:
• At a minimum distance of 40 mm from the back
panel or any other vertical surfaces.
• So that a minimum distance of 20 mm is maintained
between the installation cavity and the cabinet
underneath.
• Kitchen cabinets adjacent to the appliance and taller
than the top of the hob must be at least 600 mm
from the edge of the hob.
3
Fixing
• 400V 3 - N ~ 50 Hz
• 400V - 2+2N ~ 50 Hz
Separate the wires and connect them in accordance
with the instructions given in the following table and
diagrams:
GB
The appliance must be installed on a perfectly level
supporting surface.
Any deformities caused by improper fixing could affect
the features and operation of the hob.
The thickness of the supporting surface should be
taken into account when choosing the length of the
screws for the fixing hooks:
Voltage and
mains frequency
Electrical cable
Wire connection
400V - 2+N ~
50 Hz
: yellow/green;
• 30 mm thick: 23 mm screws
• 40 mm thick: 13 mm screws
Fix the hob as follows:
1. Use short flat-bottomed screws to fix the 4
alignment springs in the holes provided at the central
point of each side of the hob.
220-240V 3 ~
50 Hz
N: the two blue wires
together
L1: black
400V 3-N ~
50 Hz
L2: brown
: yellow/green;
2. Place the hob in the cavity, make sure it is in a
central position and push down on the whole perimeter
until the hob is stuck to the supporting surface.
3. For hobs with raised sides: After inserting the hob
into its cavity, insert the 4 fixing hooks (each has its
own pin) into the lower edges of the hob, using the
long pointed screws to fix them in place, until the
glass is stuck to the supporting surface.
N1: blue
N2: blue
L1: black
L2: brown
400V - 2+2N ~
50 Hz
Connecting the electricity supply cable to the mains
If the appliance is being connected directly to the
electricity mains an omnipolar switch must be installed
with a minimum opening of 3 mm between contacts.
! The screws for the alignment springs must remain
accessible.
! In order to adhere to safety standards, the appliance
must not come into contact with electrical parts once it
has been installed.
! All parts which ensure the safe operation of the
appliance must not be removable without the aid of a
tool.
! The installer must ensure that the correct electrical
connection has been made and that it is fully
compliant with safety regulations.
Before connecting the appliance to the power supply,
make sure that:
• The appliance is earthed and the plug is compliant
with the law.
• The socket can withstand the maximum power of the
appliance, which is indicated on the data plate
located on the appliance itself.
Electrical connection
• The voltage falls within the range of values indicated
on the data plate.
! The electrical connection for the hob and for any built-
in oven must be carried out separately, both for safety
purposes and to make extracting the oven easier.
• The socket is compatible with the plug of the
appliance. If the socket is incompatible with the
plug, ask an authorised technician to replace it. Do
not use extension cords or multiple sockets.
! Once the appliance has been installed, the power
supply cable and the electrical socket must be easily
accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced
by authorised technicians only.
! The manufacturer declines any liability should
these safety measures not be observed.
! Do not remove or replace the power supply cable for
any reason. Its removal or replacement will void the
warranty and the CE marking. INDESIT does not
assume liability for accidents or damage arising from
replacement/removal of the original power supply
cable. Replacement can only be accepted when
carried out by personnel authorised by INDESIT and
using an original spare part.
Single-phase connection
The hob is equipped with a pre-connected electricity
supply cable, which is designed for single-phase
connection. Connect the wires in accordance with the
instructions given in the following table and diagrams:
Voltage and
mains frequency
Electrical cable
Wire connection
: yellow/green
220-240V 1+N ~
50 Hz
N: the two blue wires together
L: brown and black together
Other types of connection
If the mains supply corresponds with one of the
following:
Voltage and mains frequency
• 400V - 2+N ~ 50 Hz
• 220-240V 3 ~ 50 Hz
4
Description of the
appliance
Control panel
GB
The control panel described in this manual is only a representative example: it may not exactly match the panel
on your appliance.
TIMER*
indicator light
INCREASE
POWER button
PROGRAMME TIMER*
display
BOOSTER*
button
COOKING ZONE PROGRAMMED*
indicator light
POWER and
RESIDUAL HEAT
indicators
BOOSTER*
indicator light
COOKING ZONE
SELECTED indicator light
ON/OFF
button
ON/OFF
indicator light
Booster
Booster
CONTROLS LOCKED
indicator light
CONTROL PANEL
LOCK button
COOKING ZONE
SELECTOR buttons
PROGRAMME
TIMER* button
REDUCE POWER
button
• INCREASE POWER button switches on the
hotplate and controls the power (see Start-up and
use).
• CONTROL PANEL LOCK button prevents
accidental changes to the hob settings (see Start-
up and use).
• REDUCE POWER button controls the power and
switches off the hotplate (see Start-up and use).
• COOKING ZONE SELECTOR button shows a
particular cooking zone has been selected and
therefore various adjustments are possible.
• COOKING ZONE SELECTOR button is used to
select the desired cooking zone.
• POWER indicator provides a visual display for the
current heat level.
• ON/OFF button switches the appliance on and off.
• ON/OFF indicator light shows whether the
appliance is on or off.
• PROGRAMME TIMER* button controls the
cooking programme times (see Start-up and use).
• PROGRAMME TIMER* display shows which
programme has been selected (see Start-up and
use).
• COOKING ZONE PROGRAMMED* indicator lights
show which cooking zones are being used during
a cooking programme (see Start-up and use).
• CONTROL PANEL LOCK indicator light shows
the control panel has been locked (see Start-up
and use).
• BOOSTER button* activates the booster function -
3000 W - of the cooking zone (see Start-up and
use).
• BOOSTER indicator light* shows that the booster
function has been activated.
• TIMER* indicator light shows that the timer has
been activated
! This product complies with the requirements of the
latest European Directive on the limitation of power
consumption of the standby mode.
If no operations are carried out for a period of 2
minutes, after the residual heat indicator lights turn
off and the fan stops (if present), the appliance
automatically switches to the “off mode”.
The appliance resumes the operating mode once the
ON/OFF button is pressed.
Only available in certain models.
*
5
Start-up and use
! The glue applied on the gaskets leaves traces of
grease on the glass. Before using the appliance, we
recommend you remove these with a special non-
abrasive cleaning product. During the first few hours of
use there may be a smell of rubber which will
disappear very quickly.
Switching on the hob
GB
To switch the hob on, press and hold the
for approximately one second.
button
Switching on the cooking zones
! A few seconds after the hob is connected to the
electricity supply, a buzzer will sound. The hob may
now be switched on.
Each cooking zone is controlled using a selector
button and a power adjustment device
Types of noise during normal hob operation:
• Buzz: due to the vibration of the metallic parts that
make up the induction element and the pot; it is
generated by the electromagnetic field required for
heating and increases as the power of the induction
element increases.
• Soft whistle: heard when the pot placed on the
heating zone is empty; the noise disappears once
food or water is placed into the pot.
consisting of a double
-
and
+
button.
• To begin operating a cooking zone, press the
corresponding control button and set the desired power
level (between 0 and 9) using the buttons -and
Booster function*
+
.
The booster function for some of the cooking zones
may be used to shorten heating-up times. It may be
• Crackle: produced by the vibration of materials on
the bottom of the pot due to the flow of parasitic
currents caused by electromagnetic fields
Booster
activated by pressing the
button. The indicator
light directly above the button will illuminate. This
function boosts the power to 2000 W or 3000 W,
depending on the size of the relevant cooking zone.
The booster stops automatically after 4 minutes. While
the booster for one of the cooking zones is active, the
corresponding front or rear cooking zone will operate at
a reduced power level (e.g. if the booster for the rear
left-hand hotplate has been activated, the power level
of the front left-hand hotplate will be reduced). For
further information, please refer to the Technical
description of the models.
(induction); can be more or less intense depending
on the material making up the bottom of the pot,
and decreases as the pot dimensions increase.
• Loud whistle: heard when two induction elements
of the same group function simultaneously at
maximum power and/or when the booster function is
set on the larger element while the other is auto-
adjusted. Noise is reduced by decreasing the power
level of the auto-adjusted induction element; pot
bottom layers made of different kinds of materials
are among the main causes of this noise.
• Fan noise: a fan is necessary to ensure the hob
functions correctly and to safeguard the electronic
unit from possible overheating. The fan functions at
maximum power when the large induction element is
at maximum power or when the booster function is
on; in all other cases, it works at average power
depending on the temperature detected.
Switching off the cooking zones
To switch off a cooking zone, select it using the
corresponding selector button
and:
• Press the button: the power of the cooking zone
-
Furthermore, the fan may continue to work even after
switching the hob off, if the temperature detected is
high.
will progressively decrease until it is switched off.
Programming the cooking duration
The types of noise listed above are due to induction
technology and are not necessarily operational faults.
! All the cooking zones may be programmed
simultaneously, for a duration between 1 and 99
minutes.
! If the
-
or
+
button is pressed for an extended
period of time, the display scrolls quickly though the
power levels and timer minutes.
1. Select the cooking zone using the corresponding
selector button.
2. Adjust the power level of the cooking zone.
3. Press the
programming button. The indicator
Only available in certain models.
light corresponding to the selected zone will start flashing.
*
6
3. Confirm by pressing the
button.
4. Set the cooking duration using the
buttons.
-
and
+
GB
The timer begins counting down immediately. When
the time has elapsed, a buzzer will sound (for one
minute).
5. Confirm by pressing the
button or automatic
selection occurs after 10 seconds.
Control panel lock
The timer begins counting down immediately. A buzzer
sounds for approximately 1 minute and the cooking zone
switches off when the set programme has finished.
Repeat the above procedure for each hotplate you wish to
programme.
When the hob is switched on, it is possible to lock the
oven controls in order to avoid accidental changes
being made to the settings (by children, during
cleaning, etc.). Press the
button to lock the
Using multiple programmes and the display
control panel: the indicator light above the button will
switch on.
To use any of the controls (e.g. to stop cooking), you
If one or more hotplates are programmed, the display
will show the data for the hotplate with the least time
remaining, and the light corresponding to the position
of the hotplate will flash. The lights corresponding to
the other hotplates programmed will be switched on.
To visualise the time remaining for the other programmed
must switch off this function. Press the
button for
a few moments, the indicator light will switch off and
the lock function will be removed.
Switching off the hob
hotplates, press the
button repeatedly: the time
remaining for each hotplate will be shown
sequentially in a clockwise order, starting
from the front left hotplate.
Press the button
to switch off the appliance - do not
rely solely on the pan sensor.
If the control panel lock has been activated, the
controls will continue to be locked even after the hob is
switched on again. In order to switch the hob on again,
you must first remove the lock function.
Changing the programme
1. Press the
button repeatedly until the duration
you wish to change is shown.
“Demo” mode
2. Use the
buttons to set the new duration.
It is possible to set the hob to a demonstration mode
where all the controls work normally but the heating
elements do not switch on. To activate the “demo”
mode the hob must be switched on, with all the
hotplates switched off.
3. Confirm by pressing the
button.
To cancel a programme, follow the above instructions.
At step 2, press the button: the duration decreases
-
• Press and hold the
+
and
-
buttons
progressively until it reaches 0 and switches off. The
programme resets and the display exits programming
mode.
simultaneously for 6 seconds. When the 6 seconds
have elapsed, the ON/OFF and CONTROLS
LOCKED indicator lights will flash for one second.
Timer
Release the
button;
+
and
-
buttons and press the
The hob must be switched on.
The timer can be used to set a duration up to 99
minutes.
• The display will show the text DE and MO and the
hob will be switched off.
• When the hob is switched on again it will be set to
the “demo” mode.
1. Press the
programming button until the timer
indicator light is illuminated
.
To exit this mode, follow the procedure described
above. The display will show the text DE and OF and
the hob will be switched off. When it is next switched
on, the hob will function normally.
2. Set the desired duration using the
buttons.
-
and
+
7
Overheating protection
If the electronic elements overheat, the hob switches
Practical advice on using the appliance
GB
! Use cookware made from materials which are
compatible with the induction principle (ferromagnetic
material). We especially recommend pans made from:
cast iron, coated steel or special stainless steel
adapted for induction. Use a magnet to test the
compatibility of the cookware.
off automatically and
F
appears on the display,
followed by a flashing number. When the temperature
has reached a suitable level, this message disappears
and the hob may be used again.
Safety switch
The appliance has a safety switch which automatically
switches the cooking zones off after they have been in
operation for a certain amount of time at a particular
power level. When the safety switch has been
triggered, the display shows “0”.
For example: the right rear hotplate is set to 5 and will
switch off after 5 hours of continuous operation, while
the front left hotplate is set to 2 and will switch off after
8 hours.
SUITABLE
UNSUITABLE
*
Copper,
Cast iron
Enamelled steel
Special stainless steel
Aluminium, Glass, Earthenware,
Ceramic, non magnetic Stainless steel
In addition, to obtain the best results from your hob:
• Use pans with a thick, flat base in order to fully
utilise the cooking zone.
Power level
Maximum operating time in hours
1
2
3
4
5
6
7
8
9
9
8
7
6
5
4
3
2
1
• Always use pans with a diameter which is large
enough to cover the hotplate fully, in order to use all
the available heat.
• Make sure that the base of the cookware is always
clean and dry, in order to fully utilise and extend the
life of both the cooking zones and the cookware.
Buzzer
• Avoid using the same cookware which has been
used on gas burners: the heat concentration on gas
burners may distort the base of the pan, causing it
not to adhere correctly.
This can also indicate several irregularities:
• An object (a pan, cutlery, etc.) has been placed on
the control panel for more than 10 seconds.
• Something has been spilt on the control panel.
• A button has been pressed for too long. All of the
above situations may cause the buzzer to sound.
Remove the cause of the malfunction to stop the
buzzer. If the cause of the problem is not removed,
the buzzer will keep sounding and the hob will
switch off.
Safety devices
Pan sensor
Each cooking zone is equipped with a pan sensor
device. The hotplate only emits heat when a pan with
suitable measurements for the cooking zone is placed
on it. If the indicator light is flashing, it may indicate:
• An incompatible pan
• A pan whose diameter is too small
• The pan has been removed from the hotplate.
8
Practical cooking advice
GB
Pressure cooking
Pressure cooker
Frying
ª
•
Grilling
Boiling
•
¶
Crêpes
Cooking on a high flame and browning
(roasts, steaks, escalopes, fish fillets,
fried eggs)
¶
§
Fast thickening (liquid juices)
Boiling water (pasta, rice, vegetables)
Milk
§
S
Slow thickening (dense juices)
S
¢
Bain-marie cooking
Pressure cooking after whistle
¢
£
™
Low-flame cooking (stews)
Reheating dishes
™
¡
Chocolate sauce
Keeping food hot
9
Precautions and tips
! This appliance has been designed and manufactured
in compliance with international safety standards. The
following warnings are provided for safety reasons and
must be read carefully.
• Always make sure that pan handles are turned
GB
towards the centre of the hob in order to avoid
accidental burns.
• When unplugging the appliance, always pull the plug
from the mains socket; do not pull on the cable.
• Never perform any cleaning or maintenance work
without having disconnected the appliance from the
electricity mains.
This appliance conforms to the following
European Economic Community directives:
- 2006/95/EEC dated 12/12/06 (Low Voltage) and
subsequent amendments;
• The appliance should not be operated by people
(including children) with reduced physical, sensory or
mental capacities, by inexperienced individuals or by
anyone who is not familiar with the product. These
individuals should, at the very least, be supervised
by someone who assumes responsibility for their
safety or receive preliminary instructions relating to
the operation of the appliance.
- 2004/108/EEC dated 15/12/04 (Electromagnetic
Compatibility) and subsequent amendments;
- 93/68/EEC dated 22/07/93 and subsequent
amendments.
- 1275/2008 stand-by/off mode.
• For the attention of wearers of pacemakers or
other active implants:
General safety
The hob complies with all current standards on
electromagnetic interference.
! Make sure that the air inlet behind the fan grille is
never obstructed. The built-in hob should, in fact, be
provided with suitable ventilation for the cooling of the
electronic components used in the appliance.
! We advise against the installation of an induction hob
above an under-the-counter refrigerator (heat) or above a
washing machine (vibrations). In fact, there would be
insufficient space for the ventilation of electronic
components.
• The appliance was designed for domestic use inside
the home and is not intended for commercial or
industrial use.
• The appliance must not be installed outdoors, even in
covered areas. It is extremely dangerous to leave the
appliance exposed to rain and storms.
Your induction hob is therefore perfectly in keeping
with legal requirements (89/336/CEE directives). It is
designed not to create interference on any other
electrical apparatus being used on condition that the
apparatus in question also complies with this
legislation.
Your induction hob generates short-range magnetic
fields. To avoid any interference between your
induction hob and a pacemaker, the latter must be
designed to comply with relevant regulations. In this
respect, we can only guarantee our own product
conformity. Please consult the pacemaker
manufacturer or your doctor concerning its conformity
or any possible incompatibility.
• Do not let children play with the appliance.
• Do not place metal objects (knives, spoons, pan lids,
etc.) on the hob as they may become hot.
• The appliance is not intended to be operated by
means of an external timer or separate remote-
control system.
• Do not touch the appliance when barefoot or with wet
or damp hands and feet.
• The appliance must be used by adults only for the
preparation of food, in accordance with the
instructions outlined in this booklet. Any other
use of the appliance (e.g. for heating the room)
constitutes improper use and is dangerous. The
manufacturer may not be held liable for any
damage resulting from improper, incorrect and
unreasonable use of the appliance.
• The glass ceramic hob is resistant to mechanical
shocks, but it may crack (or even break) if hit with a
sharp object such as a tool. If this happens,
disconnect the appliance from the electricity mains
immediately and contact a Service Centre.
Disposal
• When disposing of packaging material: observe local
legislation so that the packaging may be reused.
• The European Directive 2002/96/EC relating to Waste
Electrical and Electronic Equipment (WEEE) states
that household appliances should not be disposed of
using the normal solid urban waste cycle. Exhausted
appliances should be collected separately in order to
optimise the cost of re-using and recycling the
materials inside the machine, while preventing
potential damage to the atmosphere and to public
health. The crossed-out dustbin is marked on all
products to remind the owner of their obligations
regarding separated waste collection.
• Ensure that power supply cables of other electrical
appliances do not come into contact with the hot
parts of the hob.
• Remember that the cooking zones remain relatively
hot for at least thirty minutes after they have been
switched off. An indicator light provides a warning
when residual heat is present (see Start-up and use).
• Keep any object which could melt away from the hob,
for example plastic and aluminium objects, or
products with a high sugar content. Be especially
careful when using plastic film and aluminium foil or
packaging: if placed on surfaces which are still hot,
they may cause serious damage to the hob.
For further information relating to the correct disposal
of exhausted household appliances, owners may
contact the public service provided or their local
dealer.
10
Care and maintenance
Switching the appliance off
Disconnect your appliance from the electricity
supply before carrying out any work on it.
• Once it is clean, the hob may be treated with a
special protective maintenance product: the
invisible film left by this product protects the
surface from drips during cooking. This
GB
Cleaning the appliance
maintenance task should be carried out while the
appliance is warm (not hot) or cold.
! Do not use abrasive or corrosive detergents (for
example, products in spray cans for cleaning
barbecues and ovens), stain removers, anti-rust
products, powder detergents or sponges with
abrasive surfaces: these may scratch the surface
beyond repair.
• Always remember to rinse the appliance well with
clean water and dry it thoroughly: residues can
become encrusted during subsequent cooking
processes.
Stainless steel frame (only in models with outer
frame)
! Never use steam cleaners or pressure cleaners on
the appliance.
Stainless steel can be marked by hard water which
has been left on the surface for a long time, or by
cleaning products containing phosphorus.
• It is usually sufficient simply to wash the hob
using a damp sponge and dry it with absorbent
kitchen towel.
After cleaning, it is advisable to rinse the surface
well and dry it thoroughly. If water is spilt on the
surface, dry it quickly and thoroughly.
• If the hob is particularly dirty, rub it with a special
glass ceramic cleaning product, then rinse well
and dry thoroughly.
• To remove more stubborn dirt, use a suitable
scraper. Remove spills as soon as possible,
without waiting for the appliance to cool, to avoid
residues forming crusty deposits. You can
achieve excellent results by using a rust-proof
steel wire sponge - specifically designed for
glass ceramic surfaces - soaked in soapy water.
• If any plastic or sugary substances are
accidentally melted on the hob, remove them
immediately with the scraper, while the surface is
still hot.
! Some hobs have an aluminium frame which is
similar to stainless steel. Do not use any cleaning or
degreasing products which are not suitable for use
with aluminium.
Disassembling the hob
If it is necessary to disassemble the hob:
1. Loosen the screws fixing the alignment springs on
each side.
2. Loosen the screws holding the fixing hooks in
each corner.
3. Take the hob out of its installation cavity.
! Do not attempt to repair the appliance yourself. If
the appliance breaks down, contact a Service
Centre.
Technical description of
the models
The induction system is the quickest existing way of cooking. Unlike traditional hotplates where the cooking
zone heats up, with the induction system heat is generated directly inside pans which have ferromagnetic
bases.
CIA 641 C S
Hobs
CIC 642 C
Power (W)
Cooking zone
Back Left
Power (W)
I 1400 - 600 if front left*
I 2200 - B 3000*
I 2200 - B 3000*
I 1400 - 600 if back right*
7200
I 1400
I 2200 - B 3000*
Back Right
Front Left
I 2200
I 1400 - 600 if back right*
7200
Front Right
Total power
Key:
I = single induction cooking zone
B = booster: the power level of the cooking zone may be boosted to 3000 W
* = the maximum power level is limited while the booster is activated for the relevant rear cooking zone (see
Start-up and use).
11
Guarantee
12 months Parts and Labour Guarantee
Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of breakdown repairs for
twelve months from the date of purchase.
This gives you the reassurance that if, within that time, your appliance is proven to be defective because of either
workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost to you.
This guarantee is subject to the following conditions:
-
The appliance has been installed and operated correctly and in accordance with our operating and
maintenance instructions.
-
-
-
The appliance is used only on the electricity or gas supply printed on the rating plate.
The appliance has been used for normal domestic purposes only.
The appliance has not been altered, serviced, maintained, dismantled, or otherwise interfered with by any
person not authorised by us.
-
-
-
Any repair work must be undertaken by us or our appointed agent.
Any parts removed during repair work or any appliance that is replaced become our property.
The appliance is used in the United Kingdom or Republic of Ireland.
The guarantee does not cover:
-
Damage resulting from transportation, improper use, neglect or interference or as a result of improper
installation.
-
Replacement of any consumable item or accessory. These included but not limited to: plugs, cables,
batteries, light bulbs, fluorescent tubes and starters, covers and filters.
-
Replacement of any removable parts made of glass or plastic.
THIS GUARANTEE WILL NOTAPPLY IF THEAPPLIANCE HAS BEEN USED IN COMMERCIAL OR NON-
DOMESTIC PREMISES.
5 Year Parts Guarantee
Hotpoint also offers you a free 5 year parts guarantee. This additional guarantee is conditional on you registering
your appliance with us and the parts being fitted by one of our authorised engineers. There will be a charge for
our engineer’s time. To activate the extra parts warranty on your appliance, simply call our registration line on
08448 24 24 24 (Republic of Ireland 01 230 0800)
Extended Guarantees
We offer a selection of protection plans that enable you to fully cover yourself against the expense of repair bills
for the life of your policy. To find the ideal plan for you please call our advice line on 08448 226 226 (Republic of
Ireland 01 230 0233).
Free Helpdesk Service
We have a dedicated team who can provide free advice and assistance with your appliance if you experience
any technical difficulties within the first 90 days of ownership. Simply call our Hotpoint Service Hotline on 08448
224 224 (Republic of Ireland 0818 313 413) for telephone assistance, or, where necessary, to arrange for an
engineer to call.
12
After Sales Service
No one is better placed to care for your Hotpoint appliance during the course of its working life than us – the
manufacturer.
Essential Contact Information
Hotpoint Service
We are the largest service team in the country offering you access to 400 skilled telephone advisors and 1000
fully qualified engineers on call to ensure you receive fast, reliable, local service.
UK: 08448 224 224
Republic of Ireland: 0818 313 413
Please note: Our advisors will require the following information:
Model number:
Serial number:
Parts and Accessories
We supply a full range of genuine replacement parts as well as accessory products that protect and hygienically
clean your appliance to keep it looking good and functioning efficiently throughout its life.
UK: 08448 225 225
Republic of Ireland: 0818 313 413
Appliance Registration
We want to give you additional benefits of Hotpoint ownership. To activate your free 5 year parts guarantee you
must register your appliance with us.
UK: 08448 24 24 24
Republic of Ireland: 01 230 0800
Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB
Indesit Company Unit 49 Airways Industrial Estate, Dublin 17
Recycling and Disposal Information
As part of Hotpoint’s continued commitment to helping the environment, Hotpoint reserves the right to use quality,
recycled components to keep down customer costs and minimise material wastage.
Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children, remove the
door, plug, and cut the mains cable off flush with the appliance. Dispose of these parts separately to ensure that
the appliance can no longer be plugged into mains socket, and the door cannot be locked shut.
13
04/2012 - 195101117.00
XEROX FABRIANO
|