IMPORTANT
- 1 -
27" PC READY COLOR TV
OPERATING GUIDE
27MM20B
TABLE OF CONTENTS
IMPORTANT .............................................................................................................................................1
PICTURE CAUTIONS..............................................................................................................................6
ACCESSORIES........................................................................................................................................6
REMOTE CONTROL BATTERY INSTALLATION AND REPLACEMENT.....................................7
HOW TO SET UP YOUR NEW HITACHI COLOR TV.......................................................................8
HOOKUP CABLES...................................................................................................................................9
HOOKUP CABLES AND CONNECTORS .........................................................................................10
FRONT PANEL CONTROLS................................................................................................................10
REAR PANEL JACKS ...........................................................................................................................11
TV REAR PANEL CONNECTIONS.....................................................................................................12
EXTERNAL CONNECTIONS...............................................................................................................12
CONNECTING EXTERNAL VIDEO SOURCES ...............................................................................12
HOW TO USE THE REMOTE TO CONTROL YOUR TV................................................................14
USING THE REMOTE TO CONTROL YOUR VCR FUNCTIONS.................................................16
USING THE REMOTE TO CONTROL CABLE/SATELLITE BOX FUNCTIONS.........................17
IMPORTANT
Follow all warnings and instructions marked on this television receiver.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to
the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle, is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS TELEVISION SYSTEM TO RAIN OR
MOISTURE.
IMPORTANT
- 3 -
4 Do not allow anything to rest on or roll over the power cord, and do not place the TV where the
power cord is subject to traffic or abuse. This may result in a shock or fire hazard.
5 Do not attempt to service this television set yourself as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
6 Never push objects of any kind into this television set through cabinet slots as they may touch dangerous
voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the
television set.
7 If the television set has been dropped or the cabinet has been damaged, unplug this television set from the wall
outlet and refer servicing to qualified service personnel.
8 If liquid has been spilled into this television set, unplug it from the wall outlet and refer service to qualified
service personnel.
9 Do not subject your television set to impact of any kind. Be particularly careful not to damage the picture tube
surface.
10 Unplug this television set from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning.
11-1 Do not place this television set on an unstable cart, stand, or table. The television set may fall, causing
serious injury to a child or an adult, and serious damage to the appliance. Use only with a cart or stand
recommended by the manufacturer, or sold with the television set. Wall or shelf mounting should follow the
manufacturer's instructions, and should use a mounting kit approved by the manufacturer.
11-2 An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven
surfaces may cause the appliance and cart combination to overturn.
IMPORTANT
- 4 -
PROTECTION AND LOCATION OF YOUR SET
12 Do not use this television set near water, for example, near a bathtub, washbowl, kitchen sink, or laundry tub,
in a wet basement, or near a swimming pool, etc.
• Never expose the set to rain or water. If the set has been exposed to rain or water, unplug the set from the wall
outlet and refer servicing personnel.
13 Choose a place where light (artificial or sunlight) does not shine directly on the screen.
14 Avoid dusty places, since accumulated dust inside the chassis may cause failure of the set when high humidity
persists.
15 The set has slots, or openings in the cabinet for ventilation purposes, to provide reliable operation of the
receiver, and to protect from overheating. These openings must not be blocked or covered.
• Never cover the slots or openings with cloth or other material.
• Never block the bottom ventilation slots of the set by placing it on a bed, sofa, rug, etc.
• Never place the set near or over a radiator or heat register.
• Never place the set in a "built-in" enclosure, unless proper ventilation provided.
PROTECTION AND LOCATION OF YOUR SET
16-1 If an outside antenna is connected to the television set, be sure the antenna system is protected against
voltage surges and built up static charges, Section 810 of the National Electrical Code, NFPA No. 70-1975,
provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-
in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection
to grounding electrode, and requirements for the grounding electrode.
Click to see antenna grounding illustration.
16-2 Note to CATV system installer: (Only for the television set with CATV reception) This reminder is provided
to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper
grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the
building, as close to the point of cable entry as practical.
17 An outside antenna system should not be located in the vicinity of overhead power lines or other electrical
lights or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from touching such power lines or circuits as contact with them
might be fatal.
IMPORTANT
- 5 -
18 For added protection for this television set during a lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and disconnect the antenna. This will prevent damage due to
lightning and power-line surges.
OPERATION OF YOUR SET
19 This television set should be operated only from the type of power source indicated on the marking label. If you
are not sure of the type of power supply at your home, consult your television dealer or local power company. For
television sets designed to operate from battery power, refer to the operating instructions.
20 If the television set does not operate normally by following the operating instructions, unplug this set television
set from the wall outlet and refer servicing to qualified service personnel. Adjust only those controls that are
covered in the operating instructions as improper adjustment of other controls may result in damage and will often
require extensive work by a qualified technician to restore the television set to normal operation.
21 If your television set is to remain unused for a period of time, (such as when going on a holiday), turn the
television set OFF and unplug it from the wall outlet.
IF THIS SET DOES NOT OPERATE PROPERLY
22 If you are unable to restore normal operation by following the detailed procedure in your operating instructions,
do not attempt any further adjustment. Unplug the set and call your dealer or service technician.
23 Whenever the television set is damaged or fails, or a distinct change in performance indicates a need for
service, unplug the set and have it checked by a professional service technician.
24 It is normal for some TV sets to make occasional snapping or popping sounds, particularly when being turned
on or off. If the snapping or popping is continuous or frequent, unplug the set and consult your dealer or service
technician.
FOR SERVICING AND MODIFICATION
25 Do not use attachments not recommended by the television set manufacturer as they may cause hazards.
26 When replacement parts are required, be sure the service technician has used replacement parts specified by
the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in
PICTURE CAUTIONS
- 6 -
fire, electric shock, or other hazards.
27 Upon completion of any service or repairs to the television set, ask the service technician to perform routine
safety checks to determine that the television is in safe operating condition.
PICTURE CAUTIONS
Continuous On-Screen Displays such as video games, stock
market quotations, computer generated graphics, and other
fixed (non-moving) patterns can cause permanent damage to
Color Television Receivers. Such "PATTERN BURNS"
constitute misuse and are NOT COVERED by your HITACHI
Factory Warranty.
This color television receiver was intended mainly for the private viewing of
programs broadcast by TV stations, cable companies, and programs from other
video sources. Public viewing may require prior authorization from the
broadcaster or owner of the video program.
ACCESSORIES
Check that you have the following accessories before disposing of the packing material.
1. Remote Control Unit (CLU-433PC)
2. Two "AA" size, 1.5 V batteries (For Remote Control Unit).
For information regarding how to obtain these accessories, please call TOLL FREE 1-800-448-2244 for your
nearest HITACHI Authorized Parts Distributor in the continental United States. For Alaska and Hawaii, please
contact your nearest HITACHI regional office.
PART NAME
PART NO.
ILLUSTRATION
REMOTE CONTROL BATTERY INSTALLATION AND REPLACEMENT
- 7 -
27MM20B
HL00723
CLU-433PC
REMOTE CONTROL
27V TELEVISION STAND H530021
SP271B
(Not included, order
separately)
CUSTOM HITACHI
TELEVISION STAND
Excellent for VCR and
videotape storage.
Special features include curved
smoke glass doors and an
adjustable shelf. Available in
Black.
CAUTION: Television stand model SP271B is designed for use only with a 27 inch or smaller television
set. Use with larger equipment may result in instability, causing possible injury.
REMOTE CONTROL BATTERY INSTALLATION AND
REPLACEMENT
1. Open the battery cover of the remote control by pushing the notched part of the cover with your fingers.
2. Insert two new "AA" size batteries in the remote. When replacing old batteries, push them towards the springs
and lift them out.
3. Match the (+) and (-) marks in the battery compartment.
4. Replace the cover.
BOTTOM VIEW
HOW TO SET UP YOUR NEW HITACHI COLOR TV
- 8 -
CAUTIONS
1. If your television set is to remain unused for a long period of time, for instance when you go on vacation, unplug
the television from the wall outlet.
2. Do not subject the remote control to shocks such as dropping it on the floor, etc. Precision parts may be
damaged.
3. Do not allow the remote control to become wet and avoid placing it in areas of high humidity. Do not leave it on
or near a heater. Excess heat or moisture may cause the unit to cease operation.
4. If the batteries become exhausted, remote control operation may become erratic or stop altogether. Replace
the old batteries with new "AA" types.
NOTES:
1. The CHANNEL NO., VOLUME, and OFF TIMER indicators are not displayed simultaneously.
2. To operate your TV, point the remote control at the remote sensor of the TV.
HOW TO SET UP YOUR NEW HITACHI COLOR TV
ANTENNA
Unless your TV is connected to a cable TV system or to a centralized antenna system, a good outdoor color TV
antenna is recommended for the best performance. However, if you are located in an exceptionally good signal
area that is free from interference, and multiple image ghosts, an indoor antenna may be sufficient.
LOCATION
Select an area where sunlight or bright indoor illumination will not fall directly on the picture screen. Also, be sure
that the location selected allows a free flow of air to and from the back cover of the set.
To avoid cabinet warping, cabinet color changes, and increased chance of set failure, do not place the TV where
temperatures can become excessively hot, for example, in direct sunlight or near a heating appliance, etc.
VIEWING
To view the television screen at its best, test various locations in the room. The drawings below show several
suggestion.
The best picture is seen by sitting directly in front of the TV and about 6 to 9 feet from the screen. During daylight
hours, reflections from outside light may appear on the screen. If so, drapes or screens can be used to reduce the
reflection or the TV can be located in a different section of the room.
If the TV's audio output will be connected to a Hi-Fi system's external speakers, the best audio performance will
be obtained by placing the speakers equidistant from each side of the receiver cabinet and as close as possible to
the height of the picture screen center. For best stereo separation, place the external speakers at least 4 feet from
the side of the TV. Place the surround speakers to the side or behind the viewing area. Differences in room sizes
and acoustical environments will require some experimentation with speaker placement for best performance.
HOOKUP CABLES
- 9 -
CAUTION: The magnetic field of external speakers may cause the picture to distort if the
speakers are placed too close to the television. Move the speakers away from the TV until there is no picture
distortion.
HOOKUP CABLES
Most video/audio connections between components can be made with shielded video and audio cables that have
phono connectors. For best performance, video cables should use 75-Ohm coaxial shielded wire. Cables can be
purchased from most stores that sell audio/video products. Below are illustrations and names of common
connectors. Before purchasing any cables, be sure of the output and input connector types required by the
various components and the length of each cable.
"F" Type 75-Ohm Coaxial Antenna
300-Ohm Twin Lead Connector
Connector
This outdoor antenna cable must be
For connecting RF signals (antenna or
connected to an antenna adaptor (300-
cable TV) to the antenna jack on the
Ohm to 75-Ohm).
television.
Phono Connector
S-Video (Super Video) Connector
Used on all standard video and audio
This connector is used on camcorders,
cables which connect to inputs and outputs
VCRs, and laser disc players with an S-
located on the television's rear jack panel
Video feature in place of the standard
and front control panel.
video cable to produce a high-quality
picture.
HOOKUP CABLES AND CONNECTORS
- 10 -
Mouse Connector Cable (provided)
This cable is used to connect the computer
mouse port to the TV/monitor mouse
output for remote control mouse operation.
D-SUB MINI 5-Pin Cable (provided)
This cable is to connect a computer VGA
output to the D-SUB input located on the
rear panel.
HOOKUP CABLES AND CONNECTORS
ANTENNA CONNECTIONS
These sets are equipped with one VHF/UHF antenna terminal. The VHF/UHF terminal can be used for normal
TV, cable TV (CATV), a TV game, etc.
1. VHF (75 Ohm) antenna/CATV
3. When both VHF and UHF
When using a 75 Ohm coaxial cable system, disconnect antennas are connected
the VHF adaptor from the 75-Ohm receptacle and
Attach an optional ANTENNA MIXER
connect the outdoor antenna or CATV cable to a VHF 75to the TV antenna terminal and
ohm
connect the cables to the ANTENNA
MIXER.
receptacle.
Notes:
2. VHF (300 Ohm) antenna/UHF antenna
1. If an outdoor antenna/CATV is used,
disconnect the indoor antenna. Ghosting and
poor reception may result if both the indoor
and outdoor antennas/CATV are connected
at the same time
2. Consult your dealer or service store for
the ANTENNA MIXER and (VHF or UHF)
adaptor.
When using a 300-Ohm twin lead from an outdoor
antenna disconnect the (VHF or UHF) indoor antenna
leads from screws of the (VHF or UHF) adaptor, and
connect outdoor (VHF or UHF) antenna leads to these
screws of a (VHF or UHF) adapter.
3. The special converter (decoder) will be
supplied by the cable company.
FRONT PANEL CONTROLS
FRONT VIEW
REAR PANEL JACKS
- 11 -
Front Panel Illustration
See page 20 for MENU, CURSOR, and EXIT button operations.
A detailed explanation of the circled numbers is on page 12.
1 INPUT Selector
Press this button to select the current antenna source or VIDEO. Your selection is shown at the top right corner of
the screen.
2 VOLUME Level
Press these buttons for your desired sound level. The volume level will be displayed on the TV screen.
3 CHANNEL Selector
Press these buttons until the desired channel appears at the top right corner of the TV screen.
4 POWER Button
Press this button to turn the TV on or off.
NOTE: Your HITACHI TV will appear to be turned OFF if there is no video input when VIDEO is selected. If you
have no input to VIDEO, press the INPUT button until the normal broadcast picture appears. If the picture does
not appear, the power is OFF.
5 REMOTE CONTROL INFRARED Sensor
Point your remote control at this area when selecting channels, adjusting volume, etc.
NOTE: Front panel control CURSOR operation will not operate the FAMILY FAVORITES channel function.
REAR PANEL JACKS
REAR VIEW
1 Antenna Inputs
The VHF/UHF terminal can be used for normal TV, cable TV (CATV), a video game, etc.
2 Audio/Video Input
Use the audio and video inputs to connect external devices, such as VCRs, camcorders, laserdisc players, video
games, etc.
3 Audio to Hi-Fi
These jacks provide variable audio output to a separate stereo system amplifier. With this connection, the audio
to the stereo can be controlled by the television's remote control. (see pages 15)
4 S-Video
Input 1 provides S-Video (Super Video) jacks for connecting equipment with S-Video output capability.
5 PC RGB Input
TV REAR PANEL CONNECTIONS
- 12 -
Use this 15-pin D-SUB Input for your PC connection. (see page 43)
6 PC Audio Input
Connect external devices for audio in PC mode. (see page 46)
7 PC Mouse Control
Use this input for remote control mouse operation (see page46)
TIPS ON REAR PANEL CONNECTIONS
IMPORTANT: TURN POWER OFF ON THE TV/PC MONITOR AND THE PC BEFORE CONNECTING OR
DISCONNECTING ANY CABLES.
The S-Video connection is provided for high performance laserdisc players, VCRs etc., that have this feature. Use
this connection in place of the standard video connection if your device has this feature.
If your device has only one audio output (mono sound), connect it to the left audio jack on the TV.
Refer to the operating guide of your other electronic equipment for additional information on connecting your
hookup cables.
TV REAR PANEL CONNECTIONS
Rear Panel Connections Illustration
Typical full feature set-up. Follow connections that pertain to your to personal entertainment system.
EXTERNAL CONNECTIONS
CONNECTING EXTERNAL AUDIO AMPLIFIER
To control the audio level of an external audio amplifier with the remote control, connect the system as
shown below.
NOTE: To prevent damage to the speaker and distort sound, set the volume control of the audio amplifier
lower and adjust the sound using the remote control of the TV set.
CONNECTING EXTERNAL VIDEO SOURCES
The exact arrangement you use to connect the VCR, camcorder, and laserdisc player to your TV set is dependent
on the model and features of each component. Check the owners manual of each component for the location of
video and audio inputs and outputs.
CONNECTING EXTERNAL VIDEO SOURCES
- 13 -
The following connection diagrams are offered as suggestions. However, you may need to modify them to
accommodate your particular assortment of components and features. For best performance, video and audio
cables should be made from coaxial shielded wire.
Before Operating External Video Source
The input mode is changed everytime the INPUT button is pressed as shown below. Connect external source to
the INPUT terminal, then press the INPUT button as necessary to view the input source (see page 21).
INPUT MODE SELECTION ORDER
NOTE: When the TV is set to VIDEO and video signal is not received from VIDEO INPUT JACK on the jack
panel of the TV (i.e., VCR/laserdisc player, etc. is not connected or the video device is OFF), the screen will be
gray-blue.
CONNECTING MONAURAL AUDIO VCR OR VIDEO DISC PLAYER
1. Connect the cable from the VIDEO OUT of the VCR or the laserdisc player to the INPUT (VIDEO) jack on the
TV set below.
2. Connect the cable from the AUDIO OUT of the VCR or the laserdisc player to the INPUT (MONO)/L(AUDIO)
jack.
3. Press the INPUT button to view the program from the VCR or laserdisc player. The VIDEO mode disappears
automatically after approximately eight seconds.
4. Press the INPUT button to return to the previous channel.
CONNECTING STEREO VCR OR STEREO LASERDISC PLAYER
1. Connect the cable from the VIDEO OUT of the VCR or the laserdisc player to the INPUT (VIDEO) jack on the
TV.
2. Connect the cable from the AUDIO OUT R of the VCR or the laserdisc player to the INPUT (AUDIO/R) jack.
3. Connect the cable from the AUDIO OUT L of the VCR or the laserdisc player to the INPUT (AUDIO/L) jack.
4. Press the INPUT button to view the program from the VCR or laserdisc player. The mode VIDEO disappears
automatically after approximately eight seconds.
5. Press the INPUT button to return to the previous channel.
HOW TO USE THE REMOTE TO CONTROL YOUR TV
- 14 -
NOTE: Completely insert the connection cord plugs when connecting to rear panel jacks. The picture that is
played back will be abnormal if the connection is loose.
If you have an S-VHS VCR, you can use the S-INPUT cable in place of the standard video cable.
HOW TO USE THE REMOTE TO CONTROL YOUR TV
A detailed explaination of the circled numbers follows on page 19 to 21.
Remote Control Illustration
1 TV POWER Button
Press this button to turn the TV set on or off.
2 TV/CABLE/VCR Button
Press these buttons to control your TV, cable/satellite or VCR. See remote control programming section for
detailed explanation.
3 HELP Button
Press to display On-Screen Display help messages.
4 TV/PC Button
Press this button to toggle back and forth between TV and PC mode.
5 LAST CHANNEL (LST-CH) Button
Use this button to select between the last two channels viewed. (Good for watching two sporting events, etc.)
6, 12 CHANNEL SELECTOR Buttons
Enter two or three numbers to select channels. Enter 0 first for channels 1 to 9. For channels 100 and above,
press the "1" button and wait for two seconds before pressing the last two digits of channel.
Channel selection may also be performed by pressing CH up ( ) or down (
).
You may also use these buttons for channel scanning. Press and hold the CH up ( ) or down (
) buttons and
the TV will start quickly scanning through the channels. Release the CH up ( ) or down (
TV scans to the channel you wish to watch and the TV will tune to that channel.
) buttons when the
7, 8 VOLUME, MUTE Buttons
HOW TO USE THE REMOTE TO CONTROL YOUR TV
- 15 -
Press the VOLUME up ( ) or down (
) button until you obtain the desired sound level.
To turn the sound off instantly to answer the telephone, etc., press the MUTE button. Press the MUTE button
again or press the VOLUME up ( ) button to restore the sound.
9 COMMERICAL SKIP (CS) Button
Press to activate 90-second commerical skip timer. You may change channel(s) and after the 90 seconds has
lapsed, the TV will automatically tune back to your original channel.
NOTE: CS will be cancelled if you use the LST-CH or use Setup and Custom menus
10 MENU, EXIT and CURSOR buttons
All On-Screen Display features can be set or adjusted by using these buttons.
The MENU button will start the On-Screen Display.
The EXIT button will quit the On-Screen Display.
The CURSOR button will highlight functions or adjust and set different features. Pressing the cursor buttons will
give you access to the FAMILY FAVORITES CHANNELS On-Screen Display.
11 RECALL BUTTON
Press this button to display audio selected, current channel, antenna source, audio broadcast, time and on/off
time.
NOTE: You can also use the RECALL button to quickly clear many of the other On-Screen Displays.
13 INPUT Button
The INPUT button will select between the antenna signal and the video input jacks each time the button is
pressed.
USING THE REMOTE TO CONTROL YOUR VCR FUNCTIONS- 16 -
14 SLEEP Button
Press this button to display the SLEEP TIMER in the lower left corner of the screen. Every subsequent press of
this button will add 15 minutes to the timer, up to a maximum of three hours.
USING THE REMOTE TO CONTROL YOUR VCR FUNCTIONS
Operating the precoded function for your VCR
This remote is designed to operate different types of VCRs. You must first program the remote to match the
remote system of your VCR. (Refer to page 26.)
1. Turn on your VCR.
2. Aim the remote control at the front of your VCR.
3. Press the VCR button to switch to the VCR precoded mode.
4. While holding down the VCR button on the remote, enter the two digit preset code that matches your VCR as
shown on page 26. The remote will turn off your VCR when the correct two digit preset code is entered. When this
occurs, the remote control is programmed for your VCR. If the VCR does not turn off after five seconds, try a
different two digit preset code.
5. The remote will now control your VCR.
NOTES:
1. If your VCR cannot be operated after performing the above procedures, your VCR code has not been precoded
into the remote.
2. In the unlikely event that your VCR cannot be operated after performing the above procedures, please consult
your VCR operating guide.
3. The remote control will remember the codes you have programmed in until the batteries are removed from the
remote control. After replacing the batteries repeat the entire programming procedure stated above.
4. If your VCR does not have a power function, the remote will issue the CHANNEL UP ( ) function.
1 VCR Button
This allows the remote to control your VCR by setting it to VCR mode.
2 PRECODED VCR Buttons
These buttons transmit the chosen precoded VCR codes.
3 EXCLUSIVE TV Buttons
These buttons are for operating the TV.
If your VCR is a Hitachi brand, the MENU button will start your VCR on-screen display.
4 LST-CH Button
If your VCR has an "ENTER" function, this button will send the chosen VCR "+ "ENTER" code.
5 SLEEP Button
If your VCR has a "+100" function, this button will send the chosen VCR "+100" code.
NOTE: To use VCR RECORD, press the REC button twice.
USING THE REMOTE TO CONTROL CABLE/SATELLITE BOX FUNCTIONS
- 17 -
USING THE REMOTE TO CONTROL CABLE/SATELLITE BOX FUNCTIONS
A detailed explanation of the circled numbers follows page 25.
Remote Control Illustration
Operating the precoded function for your cable/satellite box.
This remote is designed to operate different types of cable boxes and digital satellite systems. You must first
program the remote to match the remote system in your cable/satellite box. (Refer to page 26.)
1. Turn on your cable/satellite box.
2. Aim the remote control at the front of your cable/satellite box.
3. Press the CABLE button to switch to cable/satellite box mode.
4. While holding down the CABLE button, enter the two digit preset code that matches your cable/satellite box as
shown on page 26. The remote will turn off your cable/satellite box when the correct two digit preset code is
entered. When this occurs, the remote control is programmed for your cable/satellite box. If the cable/satellite box
does not turn off after five seconds, try another two digit preset code.
5. The remote will now control your cable/satellite box.
NOTES:
1. If your cable/satellite box cannot be operated after performing the above procedures, your cable/satellite box
code has not been precoded into the remote.
2. In the unlikely event that your cable/satellite box cannot be operated after performing the above procedures,
please consult your cable/satellite box operating guide.
3. The remote control will remember the codes you have programmed in until the batteries are removed from the
remote control. After replacing the batteries repeat the entire programming procedure stated above.
4. If your cable/satellite box does not have a power function, the remote will issue the CHANNEL UP (
function.
)
1 CABLE Button
This button allows the remote to control your cable/satellite box by setting it to CABLE/SATELLITE mode.
2 PRECODED CABLE/SATELLITE BOX Buttons
These buttons transmit the chosen precoded CATV and satellite codes.
3 EXCLUSIVE TV Buttons
These buttons are for operating the TV.
4 LST-CH Button
If your cable/satellite box has an enter function, this button will send the cable/satellite box enter code.
5 SLEEP Button
If your cable/satellite box has a "+100" function, this button will send the cable/satellite "+100" code.
|