JW197D
User’s Manual
TCO’99
Congratulations!
You have just purchased a TCO’99 approved and labelled product! Your choice has provided you
with a product developed for professional use. Your purchase has also contributed to reducing the
burden on the environment and also to the further development of environmentally adapted
electronics products.
Why do we have environmentally labelled computers?
In many countries, environmental labelling has become an established method for encouraging the
adaptation of goods and services to the environment. With the growing manufacture and usage of
electronic equipment throughout the world, there is a recognized concern for the materials and
substances used by electronic products with regards to their eventual recycling and disposal. By
proper selection of these materials and substances, the impact on the environment can be minimized.
There are also other characteristics of a computer, such as energy consumption levels, that are
important from the viewpoints of both the work (internal) and natural (external) environments.
Electronic equipment in offices is often left running continuously, resulting in unnecessary
consumption of large amounts of energy and additional power generation. From the standpoint of
carbon dioxide emissions alone, it is vital to save energy.
What does labelling involve?
The product meets the requirements for the TCO’99 scheme which provides for international and
environmental labelling of personal computers and/or displays. The labelling scheme was developed
as a joint effort by the TCO (The Swedish Confederation of Professional Employees), Svenska
Naturskyddsforeningen (The Swedish Society for Nature Conservation) and Statens
Energimyndighet (The Swedish National Energy Administration).
Approval requirements cover a wide range of issues: ecology, ergonomics, emission of electrical and
magnetical fields, energy consumption and electrical safety.
Ecological criteria impose restrictions on the presence and use of heavy metals, brominated and
chlorinated flame retardants, and other substances. The product must be prepared for recycling and
the manufacturing site(s) shall be certified according to ISO14001 or EMAS registered.
Energy requirements include a demand that the system unit and/or display, after a certain period of
inactivity, shall reduce its power consumption to a lower level in one or more stages. The length of
time to reactivate the system unit shall be reasonable for the user.
Labelled products must meet strict environmental demands, for example, in respect of the reduction
of electrical and magnetical fields as well as work load and visual ergonomics.
3
User’s Manual
Below you will find a brief summary of the ecological requirements met by this product. The
complete ecological criteria document can be found at TCO Development’s website
TCO Development
SE-114 94 STOCKHOLM, Sweden
Fax: +46 8 782 92 07
E-mail: [email protected]
Information regarding TCO’99 approved and labelled products may also be obtained at
Ecological requirements
Flame retardants
Flame retardants may be present in printed wiring board laminates, cables, and housings. Their
purpose is to prevent, or at least to delay the spread of fire. Up to 30% by weight of the plastic in a
computer casing can consist of flame retardant substances. Many flame retardants contain bromine or
chlorine, and these flame retardants are chemically related to PCBs (polychlorinated biphenyls).
Both the flame retardants containing bromine or chlorine and the PCBs are suspected of giving rise
to health effects, including reproductive damage in fish-eating birds and mammals, due to the
bio-accumulative* processes when not disposed of in accordance with strict standards for disposal.
TCO’99 requires that plastic components weighing more than 25 grams shall not contain flame
retardants with organically bound bromine or chlorine. Flame retardants are allowed in the printed
wiring board laminates due to the lack of commercially available alternatives.
Cadmium**
Cadmium is present in rechargeable batteries and in the colour-generating layers of certain computer
displays. TCO’99 requires that batteries, the colour-generating layers of display screens, and the
electrical or electronics components shall not contain any cadmium.
Mercury**
Mercury is sometimes found in batteries, relays and switches. TCO’99 requires that batteries shall
not contain any mercury. It also demands that mercury is not present in any of the electrical or
electronics components associated with the labelled unit. There is however one exception. Mercury is,
for the time being, permitted in the back light system of flat panel monitors as there today is no
commercially available alternative. TCO aims on removing this exception when a mercury free
alternative is available.
Lead**
Lead can be found in picture tubes, display screens, solders and capacitors. TCO’99 permits the use
of lead due to the lack of commercially available alternatives, but in future requirements TCO
Development aims at restricting the use of lead.
_____________________________
* Bio-accumulative is defined as substances which accumulate in living organisms.
**Lead, Cadmium and Mercury are heavy metals which are bio-accumulative.
The display unit is an electric device which may contain hazardous materials/ components and that is
needs to be taken care of at end of life according to following information /procedure:
4
User’s Manual
RECYCLING INFORMATION
We, the Hanns.G care very much about our environment protection strategy and firmly believe that
it helps us have healthier earth via appropriate treatment and recycling of industrial technology
devices at the end-of-life.
These devices contain recyclable materials, which can be re-decomposed and re-integrated into
brand-new marvels. On the contrary, other material can be classified to hazardous and poisoned
substances. We strongly encourage you to contact the provided information to recycle this product.
For more information, please visit
5
User’s Manual
TABLE OF CONTENTS
PLUG AND PLAY............................................................................................ 18
TECHNICAL SUPPORT (FAQ) ......................................................................... 19
SPECIFICATIONS.......................................................................................... 22
6
User’s Manual
SAFETY NOTICE
1. The changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the
emission limits.
3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modification to this equipment. It is the responsibilities of the user to correct such interference.
WARNING:
To prevent fire or shock hazard, do not expose the monitor to rain or moisture. Dangerously high
voltages are present inside the monitor. Do not open the cabinet. Refer servicing to qualified
personnel only.
PRECAUTIONS
• Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub,
swimming pool or in a wet basement.
• Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a
person and cause serious damage to the appliance. Use only a cart or stand recommended by the
manufacturer or sold with the monitor. If you mount the monitor on a wall or shelf, use a
mounting kit approved by the manufacturer and follow the kit instructions.
• Slots and openings in the back and bottom of the cabinet are provided for ventilation. To ensure
reliable operation of the monitor and to protect it from overheating, be sure these openings are not
blocked or covered. Do not place the monitor on a bed, sofa, rug, or similar surface. Do not place
the monitor near or over a radiator or heat register. Do not place the monitor in a bookcase or
cabinet unless proper ventilation is provided.
• The monitor should be operated only from the type of power source indicated on the label. If you
are not sure of the type of power supplied to your home, consult your dealer or local power
company.
• Unplug the unit during a lighting storm or when it will not be used for long period of time. This
will protect the monitor from damage due to power surges.
• Do not overload power strips and extension cords. Overloading can result in fire or electric shock.
• Never push any object into the slot on the monitor cabinet. It could short circuit parts causing a
fire or electric shock. Never spill liquids on the monitor.
• Do not attempt to service the monitor by yourself; opening or removing covers can expose you to
dangerous voltages and other hazards. Please refer all servicing to qualified service personnel.
• The wall socket shall be installed near the equipment and shall be easily accessible.
7
User’s Manual
SPECIAL NOTES ON LCD MONITORS
The following symptoms are normal with LCD monitor and do not indicate a problem.
• Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the
Power Switch and then turn it on again to make sure the flicker disappears.
• You may find slightly uneven brightness on the screen depending on the desktop pattern you use.
• The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0.01% or
less such as a missing pixel or a pixel lit all of the time.
• Due to the nature of the LCD screen, an afterimage of the previous screen may remain after
switching the image, when the same image is displayed for hours. In this case, the screen is
recovered slowly by changing the image or turning off the Power Switch for hours.
• If the screen suddenly flashes erratically or the backlighting fails, please contact your dealer or
service center for repair. Do not attempt to repair the monitor yourself.
Lamp Disposal
LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR
DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS. FOR MORE
8
User’s Manual
BEFORE YOU OPERATE THE MONITOR
FEATURES
• 19” Wide screen TFT Color LCD Monitor
• Crisp, Clear Display for Windows
• Recommended Resolutions: 1440 X 900 @60Hz
• EPA ENERGY STAR®
• Ergonomic Design
• Space Saving, Compact Case Design
CHECKING THE CONTENTS OF THE PACKAGE
The product package should include the following items:
LCD Monitor
Screen
Base
Cables and User manual
DVI-D Cable
(dual input mode optional)
Power Cord
VGA Cable
User’s manual
Warranty card
Audio Cable
9
User’s Manual
INSTALLATION INSTRUCTIONS
INSTALL
REMOVE
Figure.1. Installing and Removing the Base
INSTALLATION:
1. Align the monitor with the opening in the base.
2. Note that the longer section of the base points forward.
3. Snap the monitor into its base. A clear click sound will affirm that the base is connected
correctly.
4. Verify that the monitor is securely attached to the base by looking at the bottom of the base and
making sure that the clips are fully engaged in the base.
REMOVAL:
1. Flip over the monitor so that it is upside down.
2. Press the 2 clips on the base that holds the monitor in place.
3. Gently press and hold the 2 clips while pulling the base from the monitor unit they are
unattached.
POWER
POWER SOURCE:
1. Make sure that the power cord is the correct type required in your area.
2. This LCD monitor has an Internal universal power supply that allows operation in either
100/120V AC or 220/240V AC voltage area (No user adjustment is required.)
3. Connect the AC-power cord one end to your LCD monitor’s AC-input socket, the other end to
wall-outlet.
10
User’s Manual
MAKING CONNECTIONS
CONNECTING TO A PC
Turn off your computer before performing the procedure below.
1. Connect one end of the VGA cable to the back of the monitor and connect the other end to the
computer’s D-Sub port.
2. Connect one end of the DVI-D cable (Dual input mode optional) to the back of the monitor and
connect the other end to the computer’s DVI-D port.
3. Connect the audio cable between the monitor's audio input and the PC's audio output (green
port).
4. Plug one end of the AC power cord to the LCD monitor’s AC input socket, and the other end to
Wall outlet.
5. Turn on your monitor and computer.
Figure.2. Connecting to a PC
1.
3.
Power AC Input
DVI-D Input
2.
4.
Audio Input
VGA Input
11
User’s Manual
ADJUSTING THE VIEWING ANGLE
• For optimal viewing it is recommended to look at the full face of the monitor, then adjust the
monitor’s angle to your own preference.
• Hold the stand so you do not topple the monitor when you change the monitor’s angle.
• You are able to adjust the monitor’s angle from -5° to 20°.
Monitor Angle
Figure.3.
NOTES:
• Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD
screen.
•
Be careful not to place fingers or hands near the hinges when tilting the monitor, otherwise
pinching can result.
12
User’s Manual
OPERATING INSTRUCTIONS
GENERAL INSTRUCTIONS
Press the power button to turn the monitor on or off. The other control buttons are located on the
front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to
your personal preferences.
• The power cord should be connected.
• Connect the Signal cable from the monitor to the VGA card.
• Press the power button to turn on the monitor. The power indicator will light up.
Figure.4. Control Panel Buttons
CONTROL PANEL BUTTONS:
1.
3.
5.
Volume adjustment button / ▼ [-]
Menu / Return
2.
4.
6.
Brightness adjustment button /▲ [+]
Input source change / Enter
Power Indicator
Power Button
13
User’s Manual
FRONT PANEL CONTROL
• Power Button:
Press this button to switch ON/OFF of monitor’s power.
• Power Indicator:
Green — Power On mode.
Orange — Power Saving mode.
• MENU / RETURN:
1. Turn the OSD menu on/off or return to the previous menu.
2. Exit OSD menu when in volume OSD status.
• Adjust ◄►:
1. Adjust Brightness and volume when the OSD is off.
2. Navigate through adjustment icons when OSD is ON or adjust a function when function is
activated.
• A Button:
1. Press the A button to select the input signal type. (There are VGA, DVI, HDMI, YpbPr options
available but what port you can actually select depends on your model.)
2. The OSD menu is used as “confirmation” function during start-up.
3. Press and hold this button more than 3 seconds will start 「Auto Adjust」 function when using
VGA input only. (The auto adjustment function is used to optimize the 「horizontal position」,
「vertical position」,「clock」,and 「phase」.)
NOTES:
• Do not install the monitor in a location near heat sources such as radiators or air dusts, or in a
place subject to direct sunlight, or excessive dust or mechanical vibration or shock.
• Save the original shipping box and packing materials, as they will come in handy if you ever have
to ship your monitor.
• For maximum protection, repackage your monitor as it was originally packed at the factory.
• To keep the monitor looking new, periodically clean it with a soft cloth. Stubborn stains may be
removed with a cloth lightly dampened with a mild detergent solution. Never use strong solvents
such as thinner, benzene, or abrasive cleaners, since these will damage the cabinet. As a safety
precaution, always unplug the monitor before cleaning it.
14
User’s Manual
HOW TO ADJUST A SETTINGS
BRIGHTNESS/CONTRAST
Adjust the brightness value of the display according to your
preference. Select「BRIGHTNESS」option to adjust the
brightness value.
BRIGHTNESS
CONTRAST
Adjust the contrast value of the display according to your
preference. Select「CONTRAST」option to adjust the contrast
value.
Optimal setting for high contrast images or videos. The dark and
light areas of the image are automatically detected, and the
contrast is enhanced to provide a clearer, sharper image. Also,
you may select the「X-CONTRAST」option.
X-CONTRAST
INPUT SETTING
INPUT SETTING
Select the「INPUT SETTING」option to change between analog
(VGA) or Digital (DVI) source. Enter the option and select
Analog or Digital. [Dual input mode optional]
From the Signal Selection menu, select the 「AUTO SEARCH」
option to activate or deactivate the automatic signal search
function. [For DVI/ HDMI Input only]
AUTO SEARCH
COLOR SETTING
WARM
NATURE
COOL
Adjust the color temperature value of the display according to
your preference: WARM / NATURE/ COOL.
Move the cursor to the User option and select it,
To adjust the red, enter the「R」option and adjust the level.
To adjust the green, enter the「G」option and adjust the level.
To adjust the blue, enter the「B」option and adjust the level.
USER
IMAGE SETTING
AUTO ADJUST
The auto adjustment function is used to optimize the「horizontal
position」, 「vertical position」,「clock」,and 「phase」. [For
VGA Input only]
When the aspect ratio of screen is distorted, you may make
adjustments by using this function. “FULL” indicates full screen
display, which does not ensure the image is shown as is or in
initial scale. “FIT” indicates scaling by the proportion of original
images, which may cause the screen showing black bands. [The
availability of this function depends upon the selected model]
ASPECT RATIO
15
User’s Manual
Select the「H-POSITION」option to shift the screen image to the
left or right. Enter the option and adjust the level. [For VGA
only]
H-POSITION
V-POSITION
CLOCK
Select the 「V-POSITION」option to shift the screen image up or
down. Enter the option and adjust the level. [For VGA only]
Select the 「CLOCK」option to reduce the vertical flicker of
characters on the screen. Enter the option and adjust the level.
[For VGA only]
Select the「PHASE」option to reduce the horizontal flicker of
characters on the screen. Enter the option and adjust the level.
[For VGA only]
PHASE
Select the「SHARPNESS」option to adjust the sharpness of the
display. Set the value from -2 to 2.
SHARPNESS
Transferring audio-video image by HDMI port would
cause edges of the image being cut on the screen; select「PC
Mode」to display in full screen. Enter the option and select
「VIDEO Mode」(VIDEO) or 「PC Mode」(PC). [For HDMI
Input only]
HDMI MODE
OSD SETTING
LANGUAGE
Select 「LANGUAGE」 option to change the language of the
OSD. Enter the option and select a language. [Reference only,
the OSD Language depends on the selected model]
Select「H-POSITION」option to adjust the horizontal position of
the OSD. Enter the option and adjust the level.
H-POSITION
Select 「V-POSITION」option to adjust the vertical position of
the OSD. Enter the option and adjust the level.
V-POSITION
Select「TRANSPARENCY」option to adjust the transparency of
the OSD. Enter the option and adjust the level.
TRANSPARENCY
OSD TIME-OUT
Select 「OSD TIME-OUT」option to set the OSD time out from
10 to 100 seconds. Enter the option and adjust the level.
To choose the color combination of the OSD window, select
「OSD COLOR」option under 「OSD SETTING」menu, choose
modes 1/2/3.
OSD COLOR
SYSTEM
While transferring via the HDMI port, it is recommended to set
AUDIO INPUT to HDMI; if no sound is outputted, it is
AUDIO INPUT
16
User’s Manual
recommended to select AUDIO INPUT as PC, and make sure the
PC audio output cable is connected to monitor’s LINE IN (or
AUDIO IN) port. [For HDMI Input only]
Select the「VOLUME」option to change the volume level. Enter
the option and adjust the level.
VOLUME
MUTE
Select the「MUTE」option to switch the function On or Off.
Select the 「DDC/CI」option to switch the function On or Off.
[Dual input mode optional]
DDC/CI
Select the 「FACTORY RESET」option to reset to the monitor’s
default setting. This will erase the current settings. Enter the
option and select On or Off.
FACTORY RESET
INFORMATION
Display Horizontal frequency/Vertical frequency/Resolution
information.
17
User’s Manual
PLUG AND PLAY
Plug & Play DDC2B Feature
This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD.
It allows the monitor to inform the host system of its identity and, depending on the level of DDC
used, communicate additional information about its display capabilities. The DDC2B is a
bidirectional data channel based on the I²C protocol. The host can request EDID information over the
DDC2B channel.
THIS MONITOR WILLAPPEAR TO BE NON-FUNCTIONAL IF THERE IS NO VIDEO
INPUT SIGNAL. IN ORDER FOR THIS MONITOR TO OPERATE PROPERLY, THERE
MUST BE A VIDEO INPUT SIGNAL.
This monitor meets the Green monitor standards as set by the Video Electronics Standards
Association (VESA) and/or the United States Environmental Protection Agency (EPA) and The
Swedish Confederation Employees (NUTEK). This feature is designed to conserve electrical energy
by reducing power consumption when there is no video-input signal present. When there is no video
input signal this monitor, following a time-out period, will automatically switch to power saving
mode. This reduces the monitor's internal power supply consumption. After the video input signal is
restored, full power is restored and the display is automatically redrawn. The appearance is similar to
a "Screen Saver" feature except the display is completely off. The display is restored by pressing a
key on the keyboard, or clicking the mouse.
18
User’s Manual
TECHNICAL SUPPORT (FAQ)
Q & A FOR GENERAL PROBLEMS
PROBLEM & QUESTION
Power LED is not on
POSSIBLE SOLUTION
*Check if the Power Switch is in the ON position.
*Power Cord should be connected.
*Check if the PC system is Plug & Play compatible.
*Check if the Video Card is Plug & Play compatible.
*Check if any plug pins on the VGA or DVI connector are
bent.
No Plug & Play
The display is too dark or too
bright.
*Adjust the Contrast and Brightness Controls.
Picture bounces or a wave
pattern is present in the picture
*Move electrical devices that may cause electrical
interference.
*Computer Power Switch should be in the ON position.
*Computer Video Card should be snugly seated in its slot.
*Make sure monitor’s video cable is properly connected to the
computer.
*Inspect monitor’s video cable and make sure none of the pins
are bent.
The power LED is ON (orange)
but there’s no video or no
picture.
*Make sure computer is operational by hitting the CAPS
LOCK key on the keyboard while observing the CAPS
LOCK LED. The LED should either turn ON or OFF after
hitting the CAPS LOCK key.
Missing one of the primary
colors (RED, GREEN, or
BLUE)
*Inspect the monitor’s video cable and make sure that none of
the pins are bent.
Screen image is not centered or
sized properly.
* Adjust pixel frequency CLOCK and PHASE or press hot-key
(A Button)
Picture has color defects
(white does not look white)
*Adjust RGB color or select color temperature.
*Use win 2000/ME/XP Right click anywhere on desktop and
select Properties>Settings>Screen Resolution. Use the
silder to adjust the reslution and click Apply.
The screen resolution needs to
be adjusted
No sound is outputted from
monitor’s built-in speaker
*Make sure PC audio output cable is connected to screen＇s
LINE IN port (or AUDIO IN port).
*Make sure the sound volume adjustment can be clearly
identified.
*Make sure the System > Silence option in the monitor menu
is on.
*While transferring via HDMI port but no sound is outputted,
it is recommended to select AUDIO INPUT as a PC option,
19
User’s Manual
and make sure PC audio output cable is connected to
monitor＇s LINE IN port(or AUDIO IN port). [For HDMI
Input only]
20
User’s Manual
ERROR MESSAGE & POSSIBLE SOLUTIONS
ꢀ
CABLE NOT CONNECTED :
1. Check that the signal-cable is properly connected, If the connector is loose, tighten the
connector’s screws.
2. Check the signal-cable’s connection pins for damage.
ꢀ
INPUT NOT SUPPORT :
Your computer has been set to unsuitable display mode, set the computer to display mode given
in the following table.
FACTORY PRESET TIMING TABLE:
HORIZONTAL
FREQUENCY (KHz)
31.469
VERTICAL
FREQUENCY (Hz)
70.087
MODE
RESOLUTION
1
2
720×400 @70Hz
640×480 @60Hz
640×480 @67Hz
640×480 @75Hz
800×600 @56Hz
800×600 @60Hz
800×600 @72Hz
800×600 @75Hz
832×624 @75Hz
848×480 @60Hz
1024×768 @60Hz
1024×768 @70Hz
1024×768 @75Hz
1280×720 @60Hz
1280×960 @60Hz
1280×768 @60Hz
1280×768 @75Hz
1280×1024 @60Hz
1280×1024 @75Hz
1360×768 @60Hz
1440×900 @60Hz
1440×900 @75Hz
31.469
35.000
37.500
35.156
37.879
48.077
46.875
49.725
37.879
48.363
56.476
60.023
45.000
60.000
47.776
60.776
63.981
79.976
63.981
64.981
66.981
59.940
66.667
75.000
56.250
60.317
72.188
75.000
75.000
60.132
60.004
70.069
75.029
60.000
60.000
59.870
75.070
60.020
75.025
60.020
60.050
75.070
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
21
User’s Manual
APPENDIX
SPECIFICATIONS
Driving system
Size
TFT Color LCD
19.0"
LCD Panel
Video
Pixel pitch
H-Frequency
V-Frequency
0.2835mm(H) x 0.2835mm(V)
30KHz – 80KHz
55 – 75Hz
Display Colors
Max. Resolution
Plug & Play
16.2M Colors
1440 x 900 @75Hz
VESA DDC2BTM
≤42W
ON Mode
EPA ENERGY STAR®
Power Saving Mode
OFF Mode
≤1W
≤1W
Audio output
Rated Power 1.0W rms (Per channel)
VGA
DVI
Input Terminal
Hor. : 428mm
Ver. : 278mm
Maximum Screen Size
Power Source
100~240VAC,50±3Hz,60±3Hz
Operating Temp: 0° to 50°C
Storage Temp.: -20° to 60°C
Operating Humidity: 10% to 80%
Environmental
Considerations
443 (W) x 381.5(H) x 200(D) mm
17.5 ”(W)×15.1 ”(H)×8.0 ”(D)
Dimensions
Weight (NW)
4.5 kg
***The above specification is subject to actual product specification and is subject to change without
prior notice.
NOTES:
The Maximum Resolution will depends on the display card supporting. Related issue can refer to
22
|