22 inch Wide Screen
TFT LCD Monitor
HW216
USER’S MANUAL
User’s Manual
Congratulations!
The display you have just purchased carries the TCO’03
Displays label. This means that your display is designed,
manufactured and tested according to some of the strictest
quality and environmental requirements in the world. This makes
for a high performance product, designed with the user in focus
that also minimizes the impact on our natural environment.
Some of the features of the TCO’03 Display requirements:
Ergonomics
ꢀ Good visual ergonomics and image quality in order to improve the working environment
for the user and to reduce sight and strain problems. Important parameters are
luminance, contrast, resolution, reflectance, colour rendition and image stability.
Energy
ꢀ Energy-saving mode after a certain time – beneficial both for the user and the
environment
ꢀ Electrical safety
Emissions
ꢀ Electromagnetic fields
ꢀ Noise emissions
Ecology
ꢀ The product must be prepared for recycling and the manufacturer must have a certified
environmental management system such as EMAS or ISO 14 001
ꢀ Restrictions on
ꢁ chlorinated and brominated flame retardants and polymers
ꢁ heavy metals such as cadmium, mercury and lead.
The requirements included in this label have been developed by TCO Development in
cooperation with scientists, experts, users as well as manufacturers all over the world.
Since the end of the 1980s TCO has been involved in influencing the development of IT
equipment in a more user-friendly direction. Our labelling system started with displays in
1992 and is now requested by users and IT-manufacturers all over the world.
For more information, please visit
3
User’s Manual
Recycling Information
We, Hanns.G, care very much about our environment protection strategy and firmly believe
that it helps us have healthier earth via appropriate treatment and recycling of industrial
technology devices at the end-of-life.
These devices contain recyclable materials, which can be re-decomposed and re-integrated
into brand-new marvels. On the contrary, other material can be classified to hazardous and
poisoned substances. We strongly encourage you to contact the provided information to
recycle this product.
For more information, please visit
4
User’s Manual
TABLE OF CONTENTS
SAFETY NOTICE..................................................................................................................6
BEFORE YOU OPERATE THE MONITOR...........................................................................8
INSTALLATION INSTRUCTIONS..................................................................................9
POWER..........................................................................................................................9
PLUG AND PLAY.........................................................................................................18
TECHNICAL SUPPORT (FAQ)...........................................................................................19
5
User’s Manual
SAFETY NOTICE
1. The changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
2. Shielded interface cables and AC power cord, if any, must be used in order to comply
with the emission limits.
3. The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modification to this equipment. It is the responsibilities of the user to
correct such interference.
WARNING:
To prevent fire or shock hazard, do not expose the monitor to rain or moisture. Dangerously
high voltages are present inside the monitor. Do not open the cabinet. Refer servicing to
qualified personnel only.
PRECAUTIONS
ꢀ Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry
tub, swimming pool or in a wet basement.
ꢀ Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can
injure a person and cause serious damage to the appliance. Use only a cart or stand
recommended by the manufacturer or sold with the monitor. If you mount the monitor on
a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit
instructions.
ꢀ Slots and openings in the back and bottom of the cabinet are provided for ventilation. To
ensure reliable operation of the monitor and to protect it from overheating, be sure these
openings are not blocked or covered. Do not place the monitor on a bed, sofa, rug, or
similar surface. Do not place the monitor near or over a radiator or heat register. Do not
place the monitor in a bookcase or cabinet unless proper ventilation is provided.
ꢀ The monitor should be operated only from the type of power source indicated on the
label. If you are not sure of the type of power supplied to your home, consult your dealer
or local power company.
ꢀ Unplug the unit during a lightening storm or when it will not be used for long period of
time. This will protect the monitor from damage due to power surges.
ꢀ Do not overload power strips and extension cords. Overloading can result in fire or
electric shock.
ꢀ Never push any object into the slot on the monitor cabinet. It could short circuit parts
causing a fire or electric shock. Never spill liquids on the monitor.
ꢀ Do not attempt to service the monitor by yourself; opening or removing covers can
expose you to dangerous voltages and other hazards. Please refer all servicing to
qualified service personnel.
ꢀ To ensure satisfactory operation, use the monitor only with UL listed computers which
have appropriate configured receptacles marked between 100 - 240V AC, Min. 5A.
ꢀ The wall socket shall be installed near the equipment and shall be easily accessible.
6
User’s Manual
SPECIAL NOTES ON LCD MONITORS
The following symptoms are normal with LCD monitor and do not indicate a problem.
ꢀ Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn
off the Power Switch and then turn it on again to make sure the flicker disappears.
ꢀ You may find slightly uneven brightness on the screen depending on the desktop pattern
you use.
ꢀ The LCD screen has effective pixels of 99.99% or more. It may include blemishes of
0.01% or less such as a missing pixel or a pixel lit all of the time.
ꢀ Due to the nature of the LCD screen, an afterimage of the previous screen may remain
after switching the image, when the same image is displayed for hours. In this case, the
screen is recovered slowly by changing the image or turning off the Power Switch for
hours.
ꢀ If the screen suddenly flashes erratically or the backlighting fails, please contact your
dealer or service center for repair. Do not attempt to repair the monitor yourself.
Lamp Disposal
LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR
DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS. FOR MORE
7
User’s Manual
BEFORE YOU OPERATE THE MONITOR
FEATURES
ꢀ 22” Wide screen TFT Color LCD Monitor
ꢀ Crisp, Clear Display for Windows
ꢀ Recommended Resolutions: 1680 X 1050 @60Hz
ꢀ EPA ENERGY STAR®
ꢀ Ergonomic Design
ꢀ Space Saving, Compact Case Design
CHECKING THE CONTENTS OF THE PACKAGE
The product package should include the following items:
LCD Monitor
Screen
Base
Cables and User manual
Power Cord
VGA Cable
Audio Cable
3.5mm Mini Jack to R/L
Adapter Cable
DVI-I to YPbPr Adapter Cable
DVI-D Cable (Optional)
USB Cable (Optional)
User’s Manual
8
Warranty Card
User’s Manual
INSTALLATION INSTRUCTIONS
Install
Remove
Figure 1: Installing and Removing the Base
INSTALLATION:
1. Align the monitor with the opening in the base.
2. Note that the longer section of the base points forward.
3. Snap the monitor into its base. A clear click sound will affirm that the base is connected
correctly.
4. Verify that the monitor is securely attached to the base by looking at the bottom of the
base and making sure that the clips are fully engaged in the base.
REMOVAL:
1. Flip over the monitor so that it is upside down.
2. Press the 2 clips on the base that holds the monitor in place.
3. Gently press and hold the 2 clips while pulling the base from the monitor unit they are
unattached.
POWER
POWER SOURCE:
1. Make sure that the power cord is the correct type required in your area.
2. This LCD monitor has an Internal universal power supply that allows operation in either
100/120V AC or 220/240V AC voltage area (No user adjustment is required.)
3. Connect the AC-power cord one end to your LCD monitor’s AC-input socket, the other
end to wall-outlet.
9
User’s Manual
MAKING CONNECTIONS
CONNECTING TO A PC:
Turn off your computer before performing the steps below.
1. Connect one end of the D-Sub cable to the back of the monitor and connect the other
end to the computer’s D-Sub port.
2. Connect one end of the DVI-D cable (Dual input mode optional) to the back of the
monitor and connect the other end to the computer’s DVI-D port.
3. Connect the audio cable between the monitor's audio input and the PC's audio output
(green port).
4. Connect one end of the USB cable to the back of the monitor and connect the other end
to the computer's USB port. Then you can connect any USB devices (with Type A
connector) via the four USB ports on the right side of the monitor.
5. Plug one end of the AC power cord to the LCD monitor’s AC input socket, and the other
end to Wall outlet.
6. Turn on your monitor and computer.
Figure 2: Connecting to a PC
1.
3.
5.
USB Port (Type B)
Line In Input
VGA Input
2.
4.
6.
AC Power Input
DVI / YPbPr Input
USB Ports (Type A)
10
User’s Manual
CONNECTING TO A A/V DEVICE:
Connect A/V devices via the DVI and Audio Line in connectors at the back of the monitor.
1. Connect the Y (green) connector on the DVI-I to YPbPr adapter cable to the Y output
connector on the A/V device.
2. Connect the Pb (blue) connector on the DVI-I to YPbPr adapter cable to the Pb/Cb
output connector on the A/V device.
3. Connect the Pr (red) connector on the DVI-I to YPbPr adapter cable to the Pr/Cr output
on the A/V device.
4. Connect the other end of the DVI-I to YPbPr adapter cable to the back of the monitor.
5. Connect the 3.5mm mini jack to R/L adapter cable to the audio output connector of the
A/V device and the other end to the audio input connector at the back of the monitor.
6. Turn on your monitor and A/V device.
Figure 3: Connecting A/V Devices
11
User’s Manual
ADJUSTING THE VIEWING ANGLE
1. For optimal viewing it is recommended to look at the full face of the monitor, then adjust
the monitor’s angle to your own preference.
2. Hold the stand so you do not topple the monitor when you change the monitor’s angle.
3. You are able to adjust the monitor’s angle from 0° to 20°.
°
20
Figure 4: Monitor Angle
NOTES:
ꢀ Do not touch the LCD screen when you change the angle. It may cause damage or
break the LCD screen.
ꢀ Be careful not to place fingers or hands near the hinges when tilting the monitor,
otherwise pinching can result.
12
User’s Manual
OPERATING INSTRUCTIONS
GENERAL INSTRUCTIONS
Press the power button to turn the monitor on or off. The other control buttons are located
on the front panel of the monitor (See Figure 5). By changing these settings, the picture can
be adjusted to your personal preferences.
ꢀ The power cord should be connected.
ꢀ Connect the Signal cable from the monitor to the VGA card.
Press the power button to turn on the monitor. The power indicator will light up.
ꢀ
1
2
3
4
5
6
Figure 5: Control Panel Buttons
CONTROL PANEL BUTTONS:
1.
3.
5.
i Button
Volume +
Power Button
2.
4.
6.
Volume -
Menu / Enter
Power Indicator
13
User’s Manual
CONTROL PANEL BUTTON FUNCTIONS
ꢀ Power Button:
Press this button to switch ON/OFF of monitor’s power.
ꢀ Power Indicator:
Green
— Power On mode.
Orange — Power Saving mode.
ꢀ MENU / ENTER:
1. Activates the OSD menu or confirms adjustments to settings.
2. Exit OSD volume display when in volume OSD status.
ꢀ Volume ◄/►:
1. Activate the volume control when the OSD is OFF.
2. Navigate through adjustment icons when OSD is ON or adjust a function when
function is activated.
ꢀ i Button:
1. Press this button for less than 1.5 sec. to activate the Auto Adjustment function in
Analog mode. (The Auto Adjustment function is used to optimized the H-Position,
V-Position, Clock and Phase.)
2. Press this button for more than 1.5 sec. to change input source.
(Analog->Digital->YPbPr source)
NOTES:
ꢀ Do not install the monitor in a location near heat sources such as radiators or air dusts,
or in a place subject to direct sunlight, or excessive dust or mechanical vibration or
shock.
ꢀ Save the original shipping box and packing materials, as they will come in handy if you
ever have to ship your monitor.
ꢀ For maximum protection, repackage your monitor as it was originally packed at the
factory.
ꢀ To keep the monitor looking new, periodically clean it with a soft cloth. Stubborn stains
may be removed with a cloth lightly dampened with a mild detergent solution. Never use
strong solvents such as thinner, benzene, or abrasive cleaners, since these will damage
the cabinet. As a safety precaution, always unplug the monitor before cleaning it.
ꢀ Function Key Lock:
Press the <「Volume -」, >「Volume +」 and the 「Menu」 buttons simultaneously to
enable the Function Key Lock. When the Function Key Lock is enabled, only the Power
button is active. Press the <「Volume -」, >「Volume +」 and the 「Menu」buttons
simultaneously again to unlock the function keys.
14
User’s Manual
HOW TO ADJUST A SETTING
Main Menu
FUNCTION
Brightness
DESCRIPTION
Select the「Brightness」option on the「Main Menu」. Enter the option by
pressing the 「Menu」 button again, and adjust the level.
Select the「Contrast」option on the「Main Menu」. Enter the option by
pressing the 「Menu」 button again, and adjust the level.
Contrast
Select the「Image Setting」on the 「Main Menu」, and then enter the
option.
Select the「Color Setting」option on the「Main Menu」, and then enter the
option.
Select the「OSD Setting」option on the「Main Menu」, and then enter the
option.
Select the「Other Setting」option on the「Main Menu」, and then enter the
option.
Image Setting
Color Setting
OSD Setting
Other Setting
Select the「Input Setting」option to change between the Analog (D-Sub),
Digital (DVI) or YPbPr source. Enter the option and select Analog, Digital
or YPbPr.
Input Setting
Exit
Exit the OSD menu function.
Image Setting
(Analog / Digital mode)
FUNCTION
H-position
DESCRIPTION
Select the「H-position」option to shift the screen image to the left or right.
Enter the option and adjust the level.
15
User’s Manual
Select the「V-position」option to shift the screen image up or down. Enter
the option and adjust the level.
V-position
Select the 「Clock Adjustment」option to reduce the vertical flicker of
characters on the screen. Enter the option and adjust the level.
Select the「Phase Adjustment」option to reduce the horizontal flicker of
characters on the screen. Enter the option and adjust the level.
Clock
Adjustment
Phase
Adjustment
Exit
Exit the OSD menu function.
(YPbPr mode)
FUNCTION
Black level
DESCRIPTION
Select the「Black level」option on the「Main Menu」. Enter the option and
adjust the level.
Select the「Hue」option on the「Main Menu」. Enter the option and adjust
the level.
Hue
Select the「Saturation」option on the「Main Menu」. Enter the option and
adjust the level.
Saturation
Exit
Exit the OSD menu function.
Color Setting
FUNCTION
DESCRIPTION
Warm
Nature
Cool
Select to activate the Warm color preset.
Select to activate the Nature color preset.
Select to activate the Cool color preset.
Move the cursor to the User option and select it
To adjust the red, enter the「R」option and adjust the level.
To adjust the green, enter the「G」option and adjust the level.
To adjust the blue, enter the「B」option and adjust the level.
User
16
User’s Manual
Exit
Exit the OSD menu function.
OSD Setting
FUNCTION
DESCRIPTION
Select the「OSD H-Position」option to adjust the horizontal position of the
OSD. Enter the option and adjust the level.
OSD
H-Position
Select the「OSD V-Position」option to adjust the vertical position of the
OSD. Enter the option and adjust the level.
OSD
V-position
Select the「OSD Time-out」option to set the OSD time out from 10 to 120
seconds. Enter the option and adjust the level.
OSD
Time-out
Select the「OSD Transparency」option to adjust the transparency of the
OSD. Enter the option and adjust the level.
OSD
Transparency
Select the「OSD Color」setting option to adjust the color of the OSD. Enter
the option and adjust the level.
OSD Color
Select the「Language」option to change the language of the OSD. Enter
Language
Exit
the option and select a language.
(Reference only, the OSD Language is depended on selected model)
Exit the OSD menu function.
Other Setting
FUNCTION
DDC/CI
DESCRIPTION
Select the「DDC/CI」option to switch the function On or Off.
Select the「Volume」option to set the volume level from 0 to 100. Enter the
option and adjust the level.
Volume
Select the 「Sharpness」option to adjust the sharpness of the display. Set
the value from 0 to 6.
Sharpness
17
User’s Manual
Select the「DOS mode」option to set the monitor for use with PC. Enter
the option and select 720 × 400 or 640 × 400.
DOS mode
Select the「Factory Reset」option to reset to the monitor’s default setting.
This will erase the current settings. Enter the option and select On or Off.
Exit the OSD menu function.
Factory Reset
Exit
PLUG AND PLAY
Plug & Play DDC2B Feature
This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC
STANDARD. It allows the monitor to inform the host system of its identity and, depending
on the level of DDC used, communicate additional information about its display capabilities.
The DDC2B is a bidirectional data channel based on the I²C protocol. The host can request
EDID information over the DDC2B channel.
THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE IS NO VIDEO
INPUT SIGNAL. IN ORDER FOR THIS MONITOR TO OPERATE PROPERLY, THERE
MUST BE A VIDEO INPUT SIGNAL.
This monitor meets the Green monitor standards as set by the Video Electronics Standards
Association (VESA) and/or the United States Environmental Protection Agency (EPA) and
The Swedish Confederation Employees (NUTEK). This feature is designed to conserve
electrical energy by reducing power consumption when there is no video-input signal
present. When there is no video input signal this monitor, following a time-out period, will
automatically switch to power saving mode. This reduces the monitor's internal power
supply consumption. After the video input signal is restored, full power is restored and the
display is automatically redrawn. The appearance is similar to a "Screen Saver" feature
except the display is completely off. The display is restored by pressing a key on the
keyboard, or clicking the mouse.
18
User’s Manual
TECHNICAL SUPPORT (FAQ)
Q & A FOR GENERAL PROBLEMS
PROBLEM & QUESTION
Power LED is not on
POSSIBLE SOLUTION
ꢀ Check if the Power Switch is in the ON position
ꢀ Power Cord should be connected
ꢀ Check if the PC system is Plug & Play compatible
ꢀ Check if the Video Card is Plug & Play compatible
ꢀ Check if any plug pins on the D-Sub or DVI-D
connectors are bent
No Plug & Play
Picture is dim, too bright or ꢀ Adjust the clock, phase or Contrast and Brightness
fuzzy
Controls.
Picture bounces or a wave
pattern is present in the
picture
ꢀ Move away electrical devices that may cause
electrical interference.
ꢀ Computer Power Switch should be in the ON position.
ꢀ Computer Video Card should be snugly seated in its
slot
ꢀ Make sure monitor’s video cable is properly
connected to the computer.
The power LED is ON
(orange) but there’s no ꢀ Inspect monitor’s video cable and make sure none of
video or no picture.
the pins are bent.
ꢀ Make sure computer is operational by hitting the
CAPS LOCK key on the keyboard while observing the
CAPS LOCK LED. The LED should either turn ON or
OFF after hitting the CAPS LOCK key.
Missing one of the primary
colors (RED, GREEN, or
BLUE)
ꢀ Inspect the monitor’s video cable and make sure that
none of the pins are bent.
Screen image is not
ꢀ Adjust pixel frequency CLOCK and PHASE or press
centered or sized properly.
Picture has color defects
(white does not look white)
hot-key (i Button)
ꢀ Adjust RGB color or select color temperature
ꢀ Use win 2000/ME/XP Right click anywhere on
desktop and select Properties>Settings>Screen
Resolution. Use the silder to adjust the reslution and
click Apply
The screen resolution
needs to be adjusted
19
User’s Manual
ERROR MESSAGE & POSSIBLE SOLUTIONS
ꢀ CABLE NOT CONNECTED :
1. Check that the signal-cable is properly connected, If the connector is loose, tighten
the connector’s screws.
2. Check the signal-cable’s connection pins for damage.
ꢀ INPUT NOT SUPPORT :
Your computer has been set to unsuitable display mode, set the computer to display
mode given in the following table.
RECOMMENDED AND SUPPORTED TIMING MODE:
(Analog / Digital mode)
MODE
RESOLUTION
1
2
640×480 @60Hz
640×480 @75Hz
800×600 @56Hz
800×600 @60Hz
800×600 @72Hz
800×600 @75Hz
1024×768 @60Hz
1024×768 @70Hz
1024×768 @75Hz
3
4
5
6
7
8
9
10
11
12
1280×1024 @60Hz
1280×1024 @75Hz
1680×1050 @60Hz
(YPbPr mode)
MODE
RESOLUTION
1
2
720x480i @60Hz
720x480p @60Hz
720x576i @50Hz
3
4
720x576p @50Hz
1280×720p @50Hz
1280×720p @60Hz
1920×1080i @60Hz
1920×1080p @60Hz
1920×1080i @50Hz
1920×1080p @50Hz
5
6
7
8
9
10
*** The picture performance at 480i,576i or 1080i is not guaranteed.
20
User’s Manual
APPENDIX
SPECIFICATIONS
Driving system
Size
TFT Color LCD
LCD Panel
22" (21.6” viewable)
0.276mm(H) x 0.276mm(V)
30KHz – 80KHz
50 – 75Hz
Pixel pitch
H-Frequency
V-Frequency
Video
Display Colors
16.7M Colors
Hor. :464.94mm
Ver. :290.58mm
Maximum Screen Size
Max. Resolution
Plug & Play
WSXGA+ 1680 x 1050 @75Hz
VESA DDC2BTM
ON Mode
≤50W
EPA ENERGY STAR®
Power Saving Mode ≤2W
OFF Mode
≤1W
D-Sub
DVI (Dual-Input Model)
Audio Line-In Jack
USB ports
Input Terminal
Output Terminal
Power Source
Speakers 3W x 2
100 ~ 240 VAC ±10%, 50±3Hz, 60±3Hz
Operating Temp: 0° to 35°C
Storage Temp.: -20° to 60°C
Operating Humidity: 10% to 85%
Environmental
Considerations
509(W)×410(H)×206(D) mm
20.0”(W)×16.1”(H)×8.1”(D)
Dimensions
Weight (NW)
6.8 kg (15.0 lb)
***The above specification is subject to actual product specification and is subject to change
without prior notice.
Note :
The Maximum Resolution will depends on the display card supporting. Related issue can
21
|