|
8S648FX-RZ /
8S648FX-RZ-C
Intel® Pentium® 4 Processor Motherboard
User's Manual
Rev. 1002
12ME-S648FXRZ-1002
Copyright
© 2003 GIGABYTE TECHNOLOGY CO., LTD
Copyright by GIGA-BYTE TECHNOLOGY CO., LTD. ("GBT"). No part of this manual may be reproduced or transmitted in any from
without the expressed, written permission of GBT.
Trademarks
Third-party brands and names are the property of their respective owners.
Notice
Please do not remove any labels on motherboard, this may void the warranty of this motherboard.
Due to rapid change in technology, some of the specifications might be out of date before publication of this booklet.
The author assumes no responsibility for any errors or omissions that may appear in this document nor does the author make a
commitment to update the information contained herein.
Preparing Your Computer
Computer motherboards and expansion cards contain very delicate Integrated Circuit (IC) chips. To
protect them against damage from static electricity, you should follow some precautions whenever you
work on your computer.
1. Unplug your computer when working on the inside.
2. Use a grounded wrist strap before handling computer components. If you do not have one,
touch both of your hands to a safely grounded object or to a metal object, such as the power
supply case.
3. Hold components by the edges and try not touch the IC chips, leads or connectors, or other
components.
4. Place components on a grounded antistatic pad or on the bag that came with the components
whenever the components are separated from the system.
5. Ensure that the ATX power supply is switched off before you plug in or remove the ATX power
connector on the motherboard.
Installing the motherboard to the chassis
If the motherboard has mounting holes, but they don't line up with the holes on the base and there
are no slots to attach the spacers, do not become alarmed you can still attach the spacers to the
mounting holes. Just cut the bottom portion of the spacers (the spacer may be a little hard to cut off, so
be careful of your hands). In this way you can still attach the motherboard to the base without worrying
about short circuits. Sometimes you may need to use the plastic springs to isolate the screw from the
motherboard PCB surface, because the circuit wire may be near by the hole. Be careful, don't let the
screw contact any printed circuit write or parts on the PCB that are near the fixing hole, otherwise it
may damage the board or cause board malfunctioning.
Table of Contents
Chapter 1 Introduction ................................................................................................... 5
Features Summary .................................................................................................................. 5
8S648FX-RZ Series Motherboard Layout .................................................................................. 6
Block Diagram ......................................................................................................................... 7
Hardware Installation Process .................................................................................................. 8
Step 1: Install the Central Processing Unit (CPU) .................................................................... 8
Step 1-1: CPU Installation ....................................................................................................... 9
Step 1-2: CPU Cooling Fan Installation ................................................................................. 9
Step 2: Install Memory Modules ............................................................................................. 10
Step 3: Install AGP Card ......................................................................................................... 11
Step 4: Install I/O Peripherals Cables ...................................................................................... 11
Step 4-1: I/O Back Panel Introduction ................................................................................... 11
Step 4-2: Connectors Introduction ........................................................................................ 12
Chapter 2 BIOS Setup ................................................................................................. 19
The Main Menu (For example: BIOS Ver. : F7d) ................................................................... 19
Standard CMOS Features ..................................................................................................... 21
Advanced BIOS Features ...................................................................................................... 23
IntegratedPeripherals ............................................................................................................. 24
Power Management Setup ..................................................................................................... 26
PnP/PCI Configurations ......................................................................................................... 28
PC Health Status ................................................................................................................... 29
Frequency/Voltage Control ..................................................................................................... 30
TopPerformance .................................................................................................................... 31
LoadFail-SafeDefaults ........................................................................................................... 32
LoadOptimizedDefaults ......................................................................................................... 32
Set Supervisor/User Password ............................................................................................. 33
Save & Exit Setup ................................................................................................................. 34
Exit Without Saving ................................................................................................................ 34
Chapter 3 Install Drivers .............................................................................................. 35
8S648FX-RZ Series Motherboard
- 4 -
Chapter 1 Introduction
Features Summary
CPU
y
y
y
y
y
y
y
y
y
y
y
y
y
Socket 478 for Intel® Pentium® 4 (Northwood, Prescott) with HT Technology
Intel® Pentium® 4 800/533/400MHz FSB
2nd cache depends on CPU
North Bridge: SiS 648FX
South Bridge: SiS 963L
Chipset
Memory
3 184-pin DDR DIMM sockets, supports up to 3GB DRAM (Max)
Supports DDR400/DDR333/DDR266 DIMM
Supports up to 2 unbuffered DIMM DDR400
Supports up to 3 unbuffered DIMM DDR333
Supports only 2.5V DDR SDRAM
1 AGP slot 8X/4X(1.5V) device support
5 PCI slots support
2 IDE controller provide IDE HDD/CD-ROM(IDE1, IDE2) with PIO, Bus
Master (Ultra DMA33/ATA66/ATA100/ATA133) operation modes
Can connect up to 4 IDE devices
1 Floppy port supports 2 FDD with 360K, 720K,1.2M, 1.44M and 2.88M bytes
1 Parallel port supports Normal/EPP/ECP mode
2 Serial port (COMA/COMB)
6 USB 2.0/1.1 ports (2 x Rear, 4 x Front by cable)
1 Front Audio connector
1 PS/2 Keyboard
1 PS/2 Mouse
Build in ICS 1883 Chipset (10/100 Mbit) *
1 RJ45 port *
Slots
On-Board IDE
y
y
y
y
y
y
y
y
y
y
y
y
y
y
y
y
y
y
y
y
y
y
y
y
y
y
y
On-Board Floppy
On-Board Peripherals
On-Board LAN *
On-Board Sound
CMedia 9761 CODEC
Support 2/4/6 channel
Line Out / Line In / Mic In
SPDIF Out /SPDIF In
CD In/ AUX_IN/ Game Port
Licensed AWARD BIOS
Supports Q-Flash™
BIOS
I/O Control
Hardware Monitor
IT8705
CPU/System Fan Revolution detect
CPU/System Fan Fail Warning
CPU Temperature Detect
System Voltage Detect
Additional Features
Overclocking
Supports @BIOS™
Supports EasyTune 4™
Over Voltage (DDR/AGP) by BIOS
Over Clock (DDR/AGP/CPU/PCI) by BIOS
ATX size form factor, 29.5cm x 21cm
Form Factor
"*" Only for 8S648FX-RZ.
- 5 -
Introduction
8S648FX-RZ Series Motherboard Layout
21 cm
KB_MS
ATX
SOCKET478
IDE2
ATX_12V
F_AUDIO
SiS 648FX
USB_LAN *
IDE1
AGP
AGP 8X
ICS 1883 *
CLR_CMOS
CODEC
PCI1
CD_IN
PCI2
AUX_IN
VRM10.0
PCI3
SiS 963L
BAT
PCI4
PCI5
P4 Titan
BIOS
FDD
SPDIF_IO
F_USB2
SYS _FAN
F_PANEL
PWR_LED
F_USB1
"*" Only for 8S648FX-RZ.
"#" Only for 8S648FX-RZ-C.
8S648FX-RZ Series Motherboard
- 6 -
Block Diagram
Pentium 4
Socket 478
CPU
CPUCLK+/- (100/133/200 MHz)
AGP 4X/8X
System Bus
400/533/800 MHz
AGPCLK
(66MHz)
DDR
266/333/400 MHz
ZCLK (66/133MHz)
SiS 648FX
HCLK+/- (100/133MHz)
5 PCI
RJ45 *
66/133 MHz
33 MHz
14.318 MHz
48 MHz
ICS 1883 *
BIOS
SiS 963L
Game Port
Floppy
AC97 Link
AC97
LPC BUS
IT8705
LPT Port
CODEC
PS/2
KB/Mouse
PCICLK
(33MHz)
24 MHz
6 USB
Ports
ATA33/66/100/133 33 MHz
IDE Channels
COM
Ports
ZCLK (66/133MHz)
CPUCLK+/- (100/133/200MHz)
AGPCLK (66MHz)
PCICLK (33MHz)
CLK GEN
USBCLK (48MHz)
14.318 MHz
33 MHz
HCLK+/- (100/133MHz)
"*" Only for 8S648FX-RZ.
- 7 -
Introduction
Hardware Installation Process
To set up your computer, you must complete the following steps:
Step 1- Install the Central Processing Unit (CPU)
Step 2- Install memory modules
Step 3- Install expansion cards
Step 4- Install I/O Peripherals Cables
Step 4
Step 1
Step 2
Step 4
Step 3
Step 4
Step 1: Install the Central Processing Unit (CPU)
Before installing the processor, adhere to the following warning:
1. Please make sure the CPU type is supported by the motherboard.
2. The processor will overheat without the heatsink and/or fan, resulting in permanent
irreparable damage.
3. If you do not match the CPU socket Pin 1 and CPU cut edge well, it will cause improper
installation. Please change the insert orientation.
4. Apply thermal grease between the processor and cooling fan.
5. Never run the processor without the heatsink properly and firmly attached. Permanent
damage will result.
6. Please set the CPU host frequency in accordance with your processor's specifications.
We don't recommend you to set the system bus frequency over the CPU's specification
because these specific bus frequencies are not the standard specifications for CPU,
chipset and most of the peripherals. Whether your system can run under these specific
bus frequencies properly will depend on your hardware configurations, including CPU,
Memory, Cards…etc.
HT functionality requirement content :
Enabling the functionality of Hyper-Threading Technology for your computer system
requires all of the following platform components:
- CPU: An Intel® Pentium 4 Processor with HT Technology
- Chipset: An SiS® Chipset that supports HT Technology
- BIOS: A BIOS that supports HT Technology and has it enabled
- OS: An operation system that has optimizations for HT Technology
8S648FX-RZ Series Motherboard
- 8 -
Step 1-1: CPU Installation
Figure 1.
Socket
Actuation
Lever
Pull the rod to the 90-degree directly.
Figure 2.
Locate Pin 1 in the socket and look for a (golden) cut edge on the
CPU upper corner. Insert the CPU into the socket. (Do not force the
CPU into the socket.) Then move the socket lever to the locked
position while holding pressure on the center of the CPU.
Step 1-2: CPU Cooling Fan Installation
Figure 1.
Apply the thermal tape(or grease) to provide better heat conduction
between your CPU and cooling fan.
Figure 2.
Fasten the cooling fan supporting-base onto the CPU socket on the
motherboard.
Figure 3.
Make sure the CPU fan is plugged to the CPU fan connector, than
install complete.
- 9 -
Hardware Installation Process
Step 2: Install Memory Modules
Before installing the memory modules, adhere to the following warning:
1. Please note that the DIMM module can only fit in one direction due to the one notch.
Wrong orientation will cause improper installation. Please change the insert orientation.
The motherboard has 3 dual inline memory module (DIMM) sockets. The BIOS will automatically
detects memory type and size. To install the memory module, just push it vertically into the DIMM
socket. The DIMM module can only fit in one direction due to the notch. Memory size can vary between
sockets.
Notch
DDR
1. The DIMM socket has a notch, so the DIMM
memory module can only fit in one direction.
2. Insert the DIMM memory module vertically into
the DIMM socket. Then push it down.
3. Close the plastic clip at both edges of the DIMM
sockets to lock the DIMM module.
Reverse the installation steps when you wish to
remove the DIMM module.
8S648FX-RZ Series Motherboard
- 10 -
Step 3: Install AGP Card
1. Read the relateAGP card's instruction document before install the AGP card into the computer.
2. If your AGP card has "AGP 8X/4X(1.5V) notch" (show below), please make sure your AGP card is AGP
8X/4X(1.5V).
AGP 4X/8X notch
3. Please carefully pull out the small white- drawable bar at the end of the AGP slot when you try to
install/ Uninstall the AGP card. Please align the AGP card to the onboard AGP slot and press firmly
down on the slot .Make sure your AGP card is locked by the small white- drawable bar.
Step 4: Install I/O Peripherals Cables
Step 4-1: I/O Back Panel Introduction
\
Y
X
`*
Z
[
a
^
]
_
X
Y
PS/2 Keyboard and PS/2 Mouse connector
This connector supports standard PS/2 keyboard and PS/2 mouse.
Parallel port (LPT)
Device like printer can be connected to Parallel port.
Z/[ Serial port (COMA/COMB)
Mouse and modem etc. can be connected to Serial port.
\
]
^
Game/MIDI port
This connector supports joystick, MIDI keyboard and other relate audio devices.
Line Out jack
Connect the stereo speakers or earphone to this connector.
Line In jack
Devices like CD-ROM, walkman etc. can be connect to Line In jack.
"*" Only for 8S648FX-RZ.
- 11 -
Hardware Installation Process
_
MIC In jack
Microphone can be connect to MIC In jack.
After installation of the audio driver, you are able to use 2/4/6-channel audio feature by software
selection. You can connect "Front speaker" to "Line Out" jack, Connect "Rear speaker" to
"Line In" jack and connect "Center/Subwoofer" to "MIC In" jack.
LAN port *
LAN is fast Ethernet with 10/100Mbps speed.
USB port
`
a
Before you connect your device(s) into USB connector(s), please make sure your device(s)
such as USB keyboard, mouse, scanner, zip, speaker...etc. Have a standard USB interface.
Also make sure your OS supports USB controller. If your OS does not support USB controller,
please contact OS vendor for possible patch or driver upgrade. For more information please
contact your OS ordevice(s) vendors.
Step 4-2: Connectors Introduction
1
3
2
5
9
15
11
10
16
6
12
13
8
7
4
14
1) ATX_12V
2) ATX
9) F_AUDIO
10) SUR_CEN
11) CD_IN
3) CPU_FAN
4) SYS_FAN
5) IDE1 / IDE2
6) FDD
12) AUX_IN
13) SPDIF_IO
14) F_USB1 / F_USB2
15) CLR_CMOS
16) BAT
7) PWR_LED
8) F_PANEL
"*" Only for 8S648FX-RZ.
8S648FX-RZ Series Motherboard
- 12 -
1) ATX_12V (+12V Power Connector)
This connector (ATX_12V) supplies the CPU operation voltage (Vcore).
If this "ATX_12V connector" is not connected, system cannot boot.
Pin No.
1
Definition
GND
3
1
4
2
2
3
4
GND
+12V
+12V
2) ATX (ATX Power)
AC power cord should only be connected to your power supply unit after ATX power cable and
other related devices are firmly connected to the mainboard.
Pin No. Definition
Pin No. Definition
10
1
2
3
4
5
6
7
8
9
10
3.3V
11
3.3V
20
11
3.3V
12
13
14
15
16
17
18
19
20
-12V
GND
GND
VCC
PS_ON(soft on/off)
GND
GND
GND
GND
-5V
VCC
GND
Power Good
5V SB (stand by +5V)
+12V
VCC
VCC
1
3) CPU_FAN (CPU Fan Connector)
Please note, a proper installation of the CPU cooler is essential to prevent the CPU from running
under abnormal condition or damaged by overheating. The CPU fan connector supports Max.
current up to 600 mA.
Pin No.
Definition
GND
1
2
3
1
+12V
Sense
- 13 -
Hardware Installation Process
4) SYS_FAN (System Fan Connector)
This connector allows you to link with the cooling fan on the system case to lower the system
temperature.
Pin No.
Definition
GND
1
2
3
1
+12V
Sense
5) IDE1 / IDE2 (IDE1 / IDE2 Connector)
Important Notice: Please connect first hard disk to IDE1 and connect CD-ROM to IDE2. The red
stripe of the ribbon cable must be the same side with the Pin1.
40
39
IDE2
IDE1
2
1
6) FDD (Floppy Connector)
Please connect the floppy drive ribbon cables to FDD. It supports 360K, 1.2M, 720K, 1.44M and
2.88M bytes floppy disk types.
The red stripe of the ribbon cable must be the same side with the Pin1.
33
34
1
2
8S648FX-RZ Series Motherboard
- 14 -
7) PWR_LED
PWR_LED is connect with the system power indicator to indicate whether the system is on/off.
It will blink when the system enters suspend mode. If you use dual color LED, power LED will turn
to another color.
Pin No.
Definition
MPD+
1
2
3
1
MPD-
MPD-
8) F_PANEL (2 x 10 pins Connector)
Please connect the power LED, PC speaker, reset switch and power switch etc of your chassisfront
panel to the F_PANEL connector according to the pin assignment below.
Soft Power
Connector
Speaker Connector
Message LED/
Power/
Sleep LED
IDE Hard Disk Active LED
Reset Switch
HD (IDE Hard Disk Active LED)
SPK (Speaker Connector)
Pin 1: LED anode(+)
Pin 2: LED cathode(-)
Pin 1: VCC(+)
Pin 2- Pin 3: NC
Pin 4: Data(-)
RES (Reset Switch)
Open: Normal Operation
Close: Reset Hardware System
Open: Normal Operation
Close: Power On/Off
Pin 1: LED anode(+)
Pin 2: LED cathode(-)
NC
PW (Soft Power Connector)
MSG (Message LED/ Power/ Sleep LED)
NC
- 15 -
Hardware Installation Process
9) F_AUDIO (Front Audio Connector)
If you want to use Front Audio connector, you must remove 5-6, 9-10 Jumper.
In order to utilize the front audio header, your chassis must have front audio connector. Also please
make sure the pin assigment on the cable is the same as the pin assigment on the MB header. To
find out if the chassis you are buying support front audio connector, please contact your dealer.
Please note, you can have the alternative of using front audio connector or of using rear audio
connector to play sound.
Pin No.
Definition
MIC
1
2
3
4
5
6
7
8
9
10
GND
REF
Power
10
2
9
1
Front Audio (R)
Rear Audio (R)
Reserved
No Pin
Front Audio (L)
Rear Audio (L)
10) SUR_CEN (Surround Center Connector)
Please contact your nearest dealer for optional SUR_CEN cable.
Pin No.
1
Definition
SUR OUTL
SUR OUTR
GND
5
1
6
2
2
3
4
5
6
No Pin
CENTER_OUT
BASS_OUT
11) CD_IN (CD In Connector)
Connect CD-ROM or DVD-ROM audio out to the connector.
Pin No.
Definition
CD-L
1
2
3
4
1
GND
GND
CD-R
8S648FX-RZ Series Motherboard
- 16 -
12) AUX_IN (AUX In Connector)
Connect other device(such as PCI TV Tunner audio out)to the connector.
Pin No.
Definition
AUX-L
GND
1
2
3
4
1
GND
AUX-R
13) SPDIF_IO (SPDIF In/Out Connector)
The SPDIF output is capable of providing digital audio to external speakers or compressed AC3
data to an external Dolby Digital Decoder. Use this feature only when your stereo system has
digital input function. Be careful with the polarity of the SPDIF_IO connector. Check the pin
assignment carefully while you connect the SPDIF cable, incorrect connection between the cable
and connector will make the device unable to work or even damage it. For optional SPDIF cable,
please contact your local dealer.
Pin No.
Definition
VCC
1
2
3
4
5
6
2
1
6
5
No Pin
SPDIF
SPDIFI
GND
GND
- 17 -
Hardware Installation Process
14) F_USB1 / F_USB2 (Front USB Connector)
Be careful with the polarity of the front USB connector. Check the pin assignment carefully while
you connect the front USB cable, incorrect connection between the cable and connector will make
the device unable to work or even damage it. For optional front USB cable, please contact your
local dealer.
Pin No.
Definition
Power
1
2
3
4
5
6
7
8
9
10
Power
USB DX-
USB Dy-
USB DX+
USB Dy+
GND
2
1
10
9
GND
No Pin
NC
15) CLR_CMOS (Clear CMOS)
You may clear the CMOS data to its default values by this jumper. To clear CMOS, temporarily
shor 1-2 pin. Default doesn't include the "Shunter" to prevent from improper use this jumper.
1
1
Open: Normal
Short: Clear CMOS
16) BAT (BATTERY)
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type
recommended by the manufacturer.
Dispose of used batteries according to the
manufacturer's instructions.
+
If you want to erase CMOS...
1. Turn OFF the computer and unplug the power cord.
2. Remove the battery, wait for 30 second.
3. Re-install the battery.
4. Plug the power cord and turn ON the computer.
8S648FX-RZ Series Motherboard
- 18 -
Chapter 2 BIOS Setup
BIOS Setup is an overview of the BIOS Setup Program. The program that allows users to modify the
basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it
retains the Setup information when the power is turned off.
ENTERING SETUP
Powering ON the computer and pressing <Del> immediately will allow you to enter Setup. If you require
more advanced BIOS settings, please go to "Advanced BIOS" setting menu. To enter Advanced BIOS
setting menu, press "Ctrl+F1" key on the BIOS screen.
CONTROL KEYS
<
>< >< ><
>
Move to select item
<Enter>
<Esc>
Select Item
Main Menu - Quit and not save changes into CMOS Status Page Setup Menu
and Option Page Setup Menu - Exit current page and return to Main Menu
Increase the numeric value or make changes
Decrease the numeric value or make changes
General help, only for Status Page Setup Menu and Option Page Setup Menu
Item Help
<+/PgUp>
<-/PgDn>
<F1>
<F2>
<F5>
<F6>
<F7>
Restore the previous CMOS value from CMOS, only for Option Page Setup Menu
Load the file-safe default CMOS value from BIOS default table
Load the Optimized Defaults
<F8>
Q-Flash utility
<F9>
System Information
<F10>
Save all the CMOS changes, only for Main Menu
Main Menu
The on-line description of the highlighted setup function is displayed at the bottom of the screen.
Status Page Setup Menu / Option Page Setup Menu
Press F1 to pop up a small help window that describes the appropriate keys to use and the possible
selections for the highlighted item. To exit the Help Window press <Esc>.
The Main Menu (For example: BIOS Ver. : F7d)
Once you enter Award BIOS CMOS Setup Utility, the Main Menu (as figure below) will appear on the
screen. The Main Menu allows you to select from eight setup functions and two exit choices. Use
arrow keys to select among the items and press <Enter> to accept or enter the sub-menu.
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
`
`
`
`
`
`
`
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Power Management Setup
PnP/PCI Configurations
PC Health Status
Top Performance
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Save & Exit Setup
Frequency/Voltage Control
Exit Without Saving
ESC: Quit
KLJI: Select Item
F8: Q-Flash
F10: Save & Exit Setup
Time, Date, Hard Disk Type...
- 19 -
BIOS Setup
If you can't find the setting you want, please press "Ctrl+F1" to search the advanced
option hidden.
• Standard CMOS Features
This setup page includes all the items in standard compatible BIOS.
• Advanced BIOS Features
This setup page includes all the items of Award special enhanced features.
• Integrated Peripherals
This setup page includes all onboard peripherals.
• Power Management Setup
This setup page includes all the items of Green function features.
• PnP/PCI Configuration
This setup page includes all the configurations of PCI & PnP ISA resources.
• PC Health Status
This setup page is the System auto detect Temperature, voltage, fan, speed.
• Frequency/Voltage Control
This setup page is control CPU clock and frequency ratio.
• Top Performance
If you wish to maximize the performance of your system, set "Top Performance" as "Enabled".
• Load Fail-Safe Defaults
Fail-Safe Defaults indicates the value of the system parameters which the system would be in safe
configuration.
• Load Optimized Defaults
Optimized Defaults indicates the value of the system parameters which the system would be in
best performance configuration.
• Set Supervisor Password
Change, set, or disable password. It allows you to limit access to the system and Setup, or just
to Setup.
• Set User Password
Change, set, or disable password. It allows you to limit access to the system.
• Save & Exit Setup
Save CMOS value settings to CMOS and exit setup.
• Exit Without Saving
Abandon all CMOS value changes and exit setup.
8S648FX-RZ Series Motherboard
- 20 -
Standard CMOS Features
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
Standard CMOS Features
Date (mm:dd:yy)
Time (hh:mm:ss)
Fri, Jan 9 2004
22:31:24
Item Help
Menu Level`
Change the day, month,
` IDE Primary Master
` IDE Primary Slave
` IDE Secondary Master
` IDE Secondary Slave
[None]
[None]
[None]
[None]
year
<Week>
Sun. to Sat.
Drive A
Drive B
[1.44M, 3.5"]
[None]
<Month>
Jan. to Dec.
Floppy 3 Mode Suport
[Disabled]
<Day>
Holt On
[All, But Keyboard]
1 to 31 (or maximum
allowed in the month)
Base Memory
Extended Memory
Total Memory
640K
127M
128M
<Year>
1999 to 2098
KLJI: Move
Enter: Select
+/-/PU/PD: Value
F10: Save
ESC: Exit
F1: General Help
F5: Previous Values
F6: Fail-Save Default
F7: Optimized Defaults
Date
The date format is <week>, <month>, <day>, <year>.
Week
Month
Day
The week, from Sun to Sat, determined by the BIOS and is display only
The month, Jan. Through Dec.
The day, from 1 to 31 (or the maximum allowed in the month)
The year, from 1999 through 2098
Year
Time
The times format in <hour> <minute> <second>. The time is calculated base on the 24-hour
military-time clock. For example, 1 p.m. is 13:00:00.
IDE Primary Master, Slave / IDE Secondary Master, Slave
The category identifies the types of hard disk from drive C to F that has been installed in the
computer. There are two types: auto type, and manual type. Manual type is user-definable; Auto type
which will automatically detect HDD type.
Note that the specifications of your drive must match with the drive table. The hard disk will not work
properly if you enter improper information for this category.
If you select User Type, related information will be asked to enter to the following items. Enter the information
directly from the keyboard and press <Enter>. Such information should be provided in the documenta-
tion form your hard disk vendor or the system manufacturer.
Cylinder
Head
Precomp
Number of cylinders
Number of heads
Write precomp
Landing Zone Landing zone
Sector
Number of sectors
If a hard disk has not been installed, select NONE and press <Enter>.
- 21 -
BIOS Setup
Drive A / Drive B
The category identifies the types of floppy disk drive A or drive B that has been installed in the
computer.
None
No floppy drive installed
360K, 5.25" 5.25 inch PC-type standard drive; 360K byte capacity.
1.2M, 5.25" 5.25 inch AT-type high-density drive; 1.2M byte capacity
(3.5 inch when 3 Mode is Enabled).
720K, 3.5"
3.5 inch double-sided drive; 720K byte capacity
1.44M, 3.5" 3.5 inch double-sided drive; 1.44M byte capacity.
2.88M, 3.5" 3.5 inch double-sided drive; 2.88M byte capacity.
Floppy 3 Mode Support (for Japan Area)
Disabled
Drive A
Drive B
Both
Normal Floppy Drive. (Default value)
Drive A is 3 mode Floppy Drive.
Drive B is 3 mode Floppy Drive.
Drive A & B are 3 mode Floppy Drives.
Halt on
The category determines whether the computer will stop if an error is detected during power up.
No Errors
The system boot will not stop for any error that may be detected and you
will be prompted.
All Errors
Whenever the BIOS detects a non-fatal error the system will be stopped.
All, But Keyboard The system boot will not stop for a keyboard error; it will stop for all other
errors. (Default value)
All, But Diskette
The system boot will not stop for a disk error; it will stop for all other errors.
All, But Disk/Key The system boot will not stop for a keyboard or disk error; it will stop for all
other errors.
Memory
The category is display-only which is determined by POST (Power On Self Test) of the BIOS.
Base Memory
The POST of the BIOS will determine the amount of base (or conventional) memory installed
in the system.
The value of the base memory is typically 512K for systems with 512K memory installed on
the motherboard, or 640K for systems with 640K or more memory installed on the motherboard.
Extended Memory
The BIOS determines how much extended memory is present during the POST.
This is the amount of memory located above 1 MB in the CPU's memory address map.
8S648FX-RZ Series Motherboard
- 22 -
Advanced BIOS Features
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
Advanced BIOS Features
First Boot Device
Second Boot Device
Third Boot Device
Boot Up Floppy Seek
Password Check
CPU Hyper-Threading#
Init Display First
[Floppy]
[HDD-0]
[CDROM]
[Disabled]
[Setup]
[Enabled]
[AGP]
Item Help
Menu Level`
Select Boot Device
priority
[Floppy]
Boot from floppy
[LS120]
Boot from LS120
[HDD-0]
Boot from First HDD
[HDD-1]
Boot from Second HDD
KLJI: Move
Enter: Select
+/-/PU/PD: Value
F10: Save
ESC: Exit
F1: General Help
F5: Previous Values
F6: Fail-Save Default
F7: Optimized Defaults
" # " System will detect automatically and show up when you install the Intel® Pentium®
processor with HT Technology.
4
First / Second / Third Boot Device
Floppy
LS120
HDD-0~3
SCSI
CDROM
ZIP
Select your boot device priority by Floppy.
Select your boot device priority by LS120.
Select your boot device priority by HDD-0~3.
Select your boot device priority by SCSI.
Select your boot device priority by CDROM.
Select your boot device priority by ZIP.
Select your boot device priority by USB-FDD.
Select your boot device priority by USB-ZIP.
USB-FDD
USB-ZIP
USB-CDROM Select your boot device priority by USB-CDROM.
USB-HDD
LAN
Disabled
Select your boot device priority by USB-HDD.
Select your boot device priority by LAN.
Select your boot device priority by Disabled.
Boot Up Floppy Seek
During POST, BIOS will determine the floppy disk drive installed is 40 or 80 tracks. 360K type is
40 tracks 720K, 1.2M and 1.44M are all 80 tracks.
Enabled
Disabled
BIOS searches for floppy disk drive to determine it is 40 or 80 tracks. Note that
BIOS can not tell from 720K, 1.2M or 1.44M drive type as they are all 80 tracks.
BIOS will not search for the type of floppy disk drive by track number. Note that
there will not be any warning message if the drive installed is 360K. (Default value)
Password Check
System
The system can not boot and can not access to Setup page will be denied if the
correct password is not entered at the prompt.
Setup
The system will boot, but access to Setup will be denied if the correct password
is not entered at the prompt. (Default value)
- 23 -
BIOS Setup
CPU Hyper-Threading
Enabled
Enables CPU Hyper Threading Feature. Please note that this feature is only working
for operating system with multi processors mode supported. (Default value)
Disables CPU Hyper Threading.
Disabled
Init Display First
Select the first initation of monitor or display from AGP or PCI VGA card.
AGP
PCI
Set Init display first to AGP. (Default value)
Set Init display first to PCI.
Integrated Peripherals
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
Integrated Peripherals
IDE1 Conductor Cable
IDE2 Conductor Cable
On-Chip Primary PCI IDE
On-Chip Secondary PCI IDE
AC97 Audio
[Auto]
[Auto]
Item Help
Menu Level`
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Disabled]
[3F8/IRQ4]
[2F8/IRQ3]
[378/IRQ7]
[SPP]
[Auto]
Auto-detect IDE
cable type
*
Onboard LAN device
USB Controller
USB Legacy Support
Onboard Serial Port 1
Onboard Serial Port 2
Onboard Parallel Port
Parallel Port Mode
x ECP Mode Use DMA
Game Port Address
Midi Port Address
Midi Port IRQ
[ATA66/100/133]
Set Conductor cable
to ATA66/100/133(80
-pins)
3
[ATA33]
Set Conductor cable
to ATA33(40-pins)
[201]
[330]
[10]
KLJI: Move
Enter: Select
+/-/PU/PD: Value
F10: Save
ESC: Exit
F1: General Help
F5: Previous Values
F6: Fail-Save Default
F7: Optimized Defaults
IDE1 Conductor Cable
Auto
Will be automatically detected by BIOS. (Default value)
ATA66/100
Set IDE1 Conductor Cable to ATA66/100 (Please make sure your IDE device
and cable is compatible with ATA66/100).
ATA33
Set IDE1 Conductor Cable to ATA33 (Please make sure your IDE device and
cable is compatible with ATA33).
IDE2 Conductor Cable
Auto Will be automatically detected by BIOS. (Default value)
ATA66/100
Set IDE2 Conductor Cable to ATA66/100 (Please make sure your IDE device
and cable is compatible with ATA66/100).
ATA33
Set IDE2 Conductor Cable to ATA33 (Please make sure your IDE device and
cable is compatible with ATA33).
On-Chip Primary PCI IDE
Enabled
Enable onboard 1st channel IDE port. (Default value)
Disabled
Disable onboard 1st channel IDE port.
On-Chip Secondary PCI IDE
Enabled
Enable onboard 2nd channel IDE port. (Default value)
Disabled
Disable onboard 2nd channel IDE port.
"*" Only for 8S648FX-RZ.
8S648FX-RZ Series Motherboard
- 24 -
AC97 Audio
Enabled
Disabled
Enable onboard AC'97 audio function. (Default value)
Disable this function.
On Board LAN device *
Disabled
Disable this function.
Enabled
Enable Onboard Lan Chip device. (Default value)
USB Controller
Enabled
Disabled
Enable USB Controller. (Default value)
Disable USB Controller.
USB Legacy Support
When USB keyboard or mouse is installed, please set at Enabled.
Enabled
Disabled
Enable USB keyboard or mouse support.
Disable USB keyboard or mouse support. (Default value)
Onboard Serial Port 1
Auto
BIOS will automatically setup the port 1 address.
3F8/IRQ4
2F8/IRQ3
3E8/IRQ4
2E8/IRQ3
Disabled
Enable onboard Serial port 1 and address is 3F8. (Default value)
Enable onboard Serial port 1 and address is 2F8.
Enable onboard Serial port 1 and address is 3E8.
Enable onboard Serial port 1 and address is 2E8.
Disable onboard Serial port 1.
Onboard Serial Port 2
Auto
BIOS will automatically setup the port 2 address.
3F8/IRQ4
2F8/IRQ3
3E8/IRQ4
2E8/IRQ3
Disabled
Enable onboard Serial port 2 and address is 3F8.
Enable onboard Serial port 2 and address is 2F8. (Default value)
Enable onboard Serial port 2 and address is 3E8.
Enable onboard Serial port 2 and address is 2E8.
Disable onboard Serial port 2.
Onboard Parallel port
378/IRQ7
278/IRQ5
Disabled
Enable onboard LPT port and address is 378/IRQ7. (Default value)
Enable onboard LPT port and address is 278/IRQ5.
Disable onboard LPT port.
3BC/IRQ7
Enable onboard LPT port and address is 3BC/IRQ7.
Parallel Port Mode
SPP
EPP
ECP
Using Parallel port as Standard Parallel Port. (Default value)
Using Parallel port as Enhanced Parallel Port.
Using Parallel port as Extended Capabilities Port.
Using Parallel port as ECP & EPP mode.
ECP+EPP
ECP Mode Use DMA
3
Set ECP Mode Use DMA to 3. (Default value)
1
Set ECP Mode Use DMA to 1.
"*" Only for 8S648FX-RZ.
- 25 -
BIOS Setup
Game Port Address
201
Set Game Port Address to 201. (Default value)
209
Disabled
Set Game Port Address to 209.
Disable this function.
Midi Port Address
300
Set Midi Port Address to 300.
330
Disabled
Set Midi Port Address to 330. (Default value)
Disable this function.
Midi Port IRQ
5
Set Midi Port IRQ to 5.
10
Set Midi Port IRQ to 10. (Default value)
Power Management Setup
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
Power Management Setup
ACPI Suspend Type
Soft-Off by PWR_BTTN
System After AC Back
IRQ [3-7, 9-15], NMI
ModemRingOn
PME Event Wake Up
Power On by Keyboard
Power On by Mouse
Resume by Alarm
[S1(POS)]
[Off]
[Off]
[Enabled]
[Enabled]
[Enabled]
[Disabled]
[Disabled]
[Disabled]
NA
Item Help
Menu Level`
[S1]
Set suspend type to
Power On Suspend under
ACPI OS
[S3]
Set suspend type to
Suspend to RAM under
ACPI OS
x Month Alarm
x Day (of Month)
x Time (hh:mm:ss)
0
0
0
0
KLJI: Move
Enter: Select
+/-/PU/PD: Value
F10: Save
ESC: Exit
F1: General Help
F5: Previous Values
F6: Fail-Save Default
F7: Optimized Defaults
ACPI Suspend Type
S1(POS)
S3(STR)
Set ACPI suspend type to S1. (Default value)
Set ACPI suspend type to S3.
Soft-off by PWR-BTTN
Off
The user press the power button once, he can turn off the system.
(Default value)
The user press the power button once, then he can enter suspend mode.
Suspend
System after AC Back
LastState
When AC-power back to the system, the system will return to the Last state
before AC-power off.
Off
When AC-power back to the system, the system will be in "Off" state.
(Default value)
On
When AC-power back to the system, the system will be in "On" state.
8S648FX-RZ Series Motherboard
- 26 -
IRQ [3-7, 9-15], NMI
Disabled
Disable this function.
Enabled
Enable this function. (Default value)
ModemRingOn
Disabled
Disable Modem Ring on function.
Enabled
Enable Modem Ring on function. (Default value)
PME Event Wake Up
Disabled
Disable this function.
Enabled
Enable PME as wake up event. (Default value)
Power On by Keyboard
Password
Disabled
Any Key
Enter from 1 to 8 characters to set the keyboard power on password.
Disabled this function. (Default value)
Set Keyboard power on by any key.
Power On by Mouse
Enabled
Disabled
Enable Power On by Mouse function.
Disable this function. (Default value)
Resume by Alarm
You can set "Resume by Alarm" item to enabled and key in Data/time to power on system.
Disabled
Enabled
Disable this function. (Default Value)
Enable alarm function to POWER ON system.
If RTC Alarm Lead To Power On is Enabled.
Month Alarm :
NA, 1~12
Day (of Month) :
Time ( hh: mm: ss) :
0~31
(0~23) : (0~59) : (0~59)
- 27 -
BIOS Setup
PnP/PCI Configurations
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
PnP/PCI Configurations
PCI 4 IRQ Assignment
PCI 1/5 IRQ Assignment
PCI 2 IRQ Assignment
PCI 3 IRQ Assignment
[Auto]
[Auto]
[Auto]
[Auto]
Item Help
Menu Level`
KLJI: Move
Enter: Select
+/-/PU/PD: Value
F10: Save
ESC: Exit
F1: General Help
F5: Previous Values
F6: Fail-Save Default
F7: Optimized Defaults
PCI 4 IRQ Assignment
Auto
3,4,5,7,9,10,11,12,14,15
Auto assign IRQ to PCI 4. (Default value)
Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 4.
PCI 1/PCI 5 IRQ Assignment
Auto
3,4,5,7,9,10,11,12,14,15
Auto assign IRQ to PCI 1/PCI 5. (Default value)
Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 1/PCI 5.
PCI 2 IRQ Assignment
Auto
3,4,5,7,9,10,11,12,14,15
Auto assign IRQ to PCI 2. (Default value)
Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 2.
PCI 3 IRQ Assignment
Auto
3,4,5,7,9,10,11,12,14,15
Auto assign IRQ to PCI 3. (Default value)
Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 3.
8S648FX-RZ Series Motherboard
- 28 -
PC Health Status
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
PC Health Status
Vcore
DDR25V
+3.3V
+12V
Current CPU Temperature
Current CPU FAN Speed
Current SYSTEM FAN Speed
1.54V
Item Help
Menu Level`
2.544V
3.360V
11.92V
41°C
4440 RPM
0 RPM
KLJI: Move
Enter: Select
+/-/PU/PD: Value
F10: Save
ESC: Exit
F1: General Help
F5: Previous Values
F6: Fail-Save Default
F7: Optimized Defaults
Current Voltage (V) Vcore / DDR25V / +3.3V / +12V
Detect system's voltage status automatically.
Current CPU Temperature
Detect CPU temperature automatically.
Current CPU/SYSTEM FAN Speed (RPM)
Detect CPU/SYSTEM Fan speed status automatically.
- 29 -
BIOS Setup
Frequency/Voltage Control
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
Frequency/Voltage Control
CPU Clock Ratio
Linear Frequency Control
x CPU Clock (MHz)
x DRAM Clock (MHz)
AGP/PCI Clock Control
x AGP Clock (MHz)
x PCI Clock (MHz)
AGP Voltage Control
DRAM Voltage Control
[10X]
[Disabled]
100
AUTO
[AUTO]
66
Item Help
Menu Level`
33
[Normal]
[Normal]
KLJI: Move
Enter: Select
+/-/PU/PD: Value
F10: Save
ESC: Exit
F1: General Help
F5: Previous Values
F6: Fail-Save Default
F7: Optimized Defaults
CPU Clock Ratio
This setup option will automatically assign by CPU detection.
For Willamette CPU:
8X~23X default: 14X
For C-Stepping P4:
8X,10X~24X default: 15X
For Northwood CPU:
12X~24X default: 16X
The option will display "Locked" and read only if the CPU ratio is not changeable.
Linear Frequency Control
Disabled
Disable this function. (Default value)
Enabled
Enable this function.
CPU Clock (MHz)
100MHz ~ 355MHz
Set CPU Host Clock from 100MHz to 355MHz.
If you use FSB400 Pentium 4 processor, please set "CPU Clock" to 100MHz.If you use FSB533
Pentium 4 processor, please set "CPU Clock" to 133MHz. If you use FSB800 Pentium 4
processor, please set "CPU Clock" to 200MHz.
Incorrect using it may cause your system broken. For power End-User use only!
DRAM Clock (MHz)
Please set DRAM Clock according to your requirement.
If you use DDR266 DRAM module, please set "DRAM Clock(MHz)" to Auto or 266. If you use
DDR333 DRAM module, please set "DRAM Clock(MHz)" to Auto or 333.
Incorrect using it may cause your system broken. For power End-User use only!
AGP/PCI Clock Control
AUTO
Set AGP/PCI Clock Control to AUTO. (Default value)
Manual
Set AGP/PCI Clock Control to Manual.
8S648FX-RZ Series Motherboard
- 30 -
AGP Clock (MHz)
Please set AGP Clock according to your requirement.
Incorrect using it may cause your system broken. For power End-User use only!
PCI Clock (MHz)
Please set PCI Clock according to your requirement.
Incorrect using it may cause your system broken. For power End-User use only!
AGP Voltage Control
Normal
Set AGP Voltage Control to Normal. (Default value)
+0.1V
Set AGP Voltage Control to +0.1V.
DRAM Voltage Control
Normal
Set DRAM Voltage Control to Normal. (Default value)
+0.1V
Set DRAM Voltage Control to +0.1V.
Top Performance
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
`
`
`
`
`
`
`
Standard CMOS Features
Advanced BIOS Features
Integrated Peri
Top Performance
Load Fail-Safe Defaults
faults
ssword
Top Performance
Power Managemen
Disabled.........................[„]
PnP/PCI Configu
ng
Enabled..........................[ ]
PC Health Statu
Frequency/Volta
ESC: Quit
em
KL: Move
ENTER: Accept
F8: Q-Flash
Setup
ESC: Abort
If you wish to maximize the performance of your system, set "Top Performance" as "Enabled".
Disabled Disable this function. (Default Value)
Enabled Enable Top Performance function.
"Top Performance" will increase H/W working speed. Different system configuration (both H/W
component and OS) will effect the result. For example, the same H/W configuration might not run
properly with Windows XP, but works smoothly with Windows NT. Therefore, if your system is not
perform enough, the reliability or stability problem will appear sometimes, and we will recommend you
disabling the option to avoid the problem as mentioned above.
- 31 -
BIOS Setup
Load Fail-Safe Defaults
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
`
`
`
`
`
`
`
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Power Management Setup
Top Performance
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
PnP/PCI CLoad Fail-Safe Defaults(Y/N)?N
PC Health Status
Save & Exit Setup
Frequency/Voltage Control
Exit Without Saving
ESC: Quit
KLJI: Select Item
F8: Q-Flash
F10: Save & Exit Setup
Load Fail-Safe Defaults
Fail-Safe defaults contain the most appropriate values of the system parameters that allow minimum
system performance.
Load Optimized Defaults
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
`
`
`
`
`
`
`
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Power Management Setup
Top Performance
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
PnP/PCI CLoad Optimized Defaults(Y/N)?N
PC Health Status
Save & Exit Setup
Frequency/Voltage Control
Exit Without Saving
ESC: Quit
KLJI: Select Item
F8: Q-Flash
F10: Save & Exit Setup
Load Optimized Defaults
Selecting this field loads the factory defaults for BIOS and Chipset Features which the system automatically
detects.
8S648FX-RZ Series Motherboard
- 32 -
Set Supervisor/User Password
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
`
`
`
`
`
`
`
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Power Management Setup
PnP/PCI CEnter Password:
PC Health Status
Top Performance
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Save & Exit Setup
Frequency/Voltage Control
Exit Without Saving
ESC: Quit
KLJI: Select Item
F8: Q-Flash
F10: Save & Exit Setup
Change/Set/Disable Password
When you select this function, the following message will appear at the center of the screen to assist you
in creating a password.
Type the password, up to eight characters, and press <Enter>. You will be asked to confirm the password.
Type the password again and press <Enter>. You may also press <Esc> to abort the selection and not
enter a password.
To disable password, just press <Enter> when you are prompted to enter password. A message
"PASSWORD DISABLED" will appear to confirm the password being disabled. Once the password is
disabled, the system will boot and you can enter Setup freely.
The BIOS Setup program allows you to specify two separate passwords:
SUPERVISOR PASSWORD and a USER PASSWORD. When disabled, anyone may access all BIOS
Setup program function. When enabled, the Supervisor password is required for entering the BIOS
Setup program and having full configuration fields, the User password is required to access only basic
items.
If you select "System" at "Password Check" in Advance BIOS Features Menu, you will be prompted
for the password every time the system is rebooted or any time you try to enter Setup Menu.
If you select "Setup" at "Password Check" in Advance BIOS Features Menu, you will be prompted only
when you try to enter Setup.
- 33 -
BIOS Setup
Save & Exit Setup
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
`
`
`
`
`
`
`
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Power Management Setup
PnP/PCI C
PC Health Status
Top Performance
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Save to CMOS and EXIT(Y/N)?Y
Save & Exit Setup
Frequency/Voltage Control
Exit Without Saving
ESC: Quit
KLJI: Select Item
F8: Q-Flash
F10: Save & Exit Setup
Save Data to CMOS
Type "Y" will quit the Setup Utility and save the user setup value to RTC CMOS.
Type "N" will return to Setup Utility.
Exit Without Saving
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
`
`
`
`
`
`
`
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Power Management Setup
PnP/PCI C
PC Health Status
Top Performance
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Quit Without Saving(Y/N)?N
Save & Exit Setup
Frequency/Voltage Control
Exit Without Saving
ESC: Quit
KLJI: Select Item
F8: Q-Flash
F10: Save & Exit Setup
Abandon all Data
Type "Y" will quit the Setup Utility without saving to RTC CMOS.
Type "N" will return to Setup Utility.
8S648FX-RZ Series Motherboard
- 34 -
Chapter 3 Install Drivers
Install Drivers
Pictures below are shown in Windows XP
Insert the driver CD-title that came with your motherboard into your CD-ROM drive, the driver
CD-title will auto start and show the installation guide. If not, please double click the CD-ROM
device icon in "My computer", and execute the setup.exe.
INSTALL CHIPSET DRIVER
This page shows the drivers that need to be installed for the system. Click each item to install the driver
manually or switch to the
to install the drivers automatically.
The "Xpress Install" uses the"Click and Go" technology to install the drivers automatically. Just select the
drivers you want then click the "GO" button. The will execute the installation for you by itself.
We recommend that you install all components in the list.
Massage: Some device drivers will restart your
system automatically. After restarting your system the
"Xpress Install" will continue to install other drivers.
Click "GO".
- 35 -
Driver Installation
Driver install finished!! you have to reboot system!!
Item Description
„
„
„
„
„
SIS AGP Driver
Install SIS AGP Driver.
USB Patch for WinXP
This patch driver can help you to resolve the USB device wake up S3 hang up issue in XP.
SiS PCI Lan Driver *
For SiS series Lan driver.
C-Media AC97 Audio Driver
Install C-Media AC97 audio driver.
SIS USB 2.0 Driver
It is recommended that you use the Microsoft Windows update for the most updated driver
for XP/2K.
"*" Only for 8S648FX-RZ.
8S648FX-RZ Series Motherboard
- 36 -
- 37 -
Memo
8S648FX-RZ Series Motherboard
- 38 -
- 39 -
Memo
CONTACT US
Contact us via the information in this page all over the world.
y
Taiwan
y
The Netherlands
Gigabyte Technology Co., Ltd.
Giga-Byte Technology B.V.
Address: No.6, Bau Chiang Road, Hsin-Tien, Taipei Hsien,
Taiwan, R.O.C.
Address: Verdunplein 8 5627 SZ, Eindhoven, The Netherlands
Tel: +31 40 290 2088
Tel: 886 (2) 8912-4888
Fax: 886 (2) 8912-4003
Tech. Support:
NLTech.Support : 0900-GIGABYTE (0900-44422983, 0.2/M)
BE Tech.Support : 0900-84034 ( 0.4/M)
Fax: +31 40 290 2089
Non-Tech. Support (Sales/Marketing issues):
Tech. Support:
Non-Tech. Support (Sales/Marketing issues):
y
USA
G.B.T. INC.
y
China
Address: 17358 Railroad St, City of Industry, CA 91748.
Tel: 1 (626) 854-9338
NINGBO G.B.T. Tech. Trading CO., Ltd.
Tech. Support:
Fax: 1 (626) 854-9339
Tech. Support:
Non-Tech. Support (Sales/Marketing issues):
Non-Tech. Support (Sales/Marketing issues):
Beijing
Tel: 86-10-82856054, 86-10-82856064, 86-10-82856094
Fax: 86-10-82856575
y
Germany
G.B.T. Technology Trading GmbH
Tel: 49-40-2533040
Chengdu
Tel: 86-28-85236930
49-01803-428468 (Tech.)
Fax: 86-28-85256822
Fax: 49-40-25492343 (Sales)
49-01803-428329 (Tech.)
GuangZhou
Tel: 86-20-87586273
Tech. Support:
Fax: 86-20-87544306
Non-Tech. Support (Sales/Marketing issues):
Shanghai
Tel: 86-21-64737410
Fax: 86-21-64453227
Shenyang
y
Japan
Tel: 86-24-23960918, 86-24-23960893
Wuhan
Nippon Giga-Byte Corporation
Tel: 86-27-87854385, 86-27-87854802
Fax: 86-27-87854031
Xian
Tel: 86-29-5531943
Fax: 86-29-5539821
y
U.K
G.B.T. TECH. CO. LTD.
Tel: 44-1908-362700
Fax: 44-1908-362709
Tech. Support:
Non-Tech. Support (Sales/Marketing issues):
8S648FX-RZ Series Motherboard
- 40 -
|