Gigabyte 7VT600 RZ C User Manual

7VT600-RZ /

7VT600-RZ-C

AMD Athlon^™/ Athlon^™XP / Duron^™Socket A Processor Motherboard

User's Manual

Rev. 1003

12ME-7VT600RZ-1003

CopyrightbyGIGA-BYTETECHNOLOGYCO.,LTD. ("GBT"). Nopartofthismanualmaybereproduced ortransmitted inanyfrom

withoutthe expressed,written permission ofGBT.

Trademarks

Third-partybrandsand namesare the propertyof theirrespective owners.

Notice

Please do not remove anylabelson motherboard, thismayvoid the warrantyofthismotherboard.

Due to rapid change in technology, some of the specificationsmightbe outofdatebefore publication ofthisbooklet.

The authorassumesnoresponsibilityfor anyerrorsoromissionsthatmayappearin thisdocument nordoesthe authormake a

commitmentto updatetheinformationcontained herein.

Preparing Your Computer

Computer motherboards and expansion cards contain very delicate Integrated Circuit(IC) chips. To

protectthem againstdamagefrom static electricity, youshouldfollowsomeprecautions wheneveryou

work on your computer.

1. Unplug yourcomputer when working onthe inside.

2. Use agroundedwrist strap beforehandlingcomputer components.Ifyou do nothaveone,

touch both ofyour hands to a safelygrounded object or to a metal object, such as the power

supplycase.

3. Hold components bythe edges and trynottouch the IC chips, leads or connectors, or other

components.

4. Place components on agrounded antistatic pad or on thebag thatcame withthe components

whenever the componentsare separated from the system.

5. Ensure that theATX power supply is switched off before you plug inor remove the ATX power

connectoronthemotherboard.

Installing the motherboard to the chassis

Ifthemotherboardhasmountingholes,buttheydon'tlineup withtheholesonthebase andthereare

noslots to attachthe spacers, do notbecome alarmedyou can still attach thespacers to themounting

holes.Justcutthebottomportionofthespacers (thespacer maybe a littlehard to cutoff,so be carefulof

your hands).In this way you can still attach the motherboard to the base without worrying aboutshort

circuits. Sometimes youmayneed to use theplastic springs toisolate the screw from the motherboard

PCBsurface, because the circuitwire maybe near by the hole. Be careful, don'tlet the screw contact

anyprintedcircuitwriteor partson thePCB thatare near the fixinghole, otherwise it maydamage the

boardorcauseboardmalfunctioning.

Table of Content

Chapter1 Introduction ................................................................................................5

FeaturesSummary..............................................................................................................................5

7VT600-RZSeriesMotherboardLayout..............................................................................................7

BlockDiagram .....................................................................................................................................8

HardwareInstallation Process ............................................................................................................9

Step 1: Set System Jumper (JP1) ......................................................................................................9

Step 2: Install the Central Processing Unit (CPU) ...........................................................................10

Step 2-1: CPU Installation .........................................................................................................10

Step 2-2: CPU Cooling Fan Installation ....................................................................................10

Step 3: InstallMemory Modules ....................................................................................................... 11

Step4: InstallExpansion Cards .......................................................................................................12

Step 5: Install I/O Peripherals Cables ..............................................................................................12

Step 5-1: I/O Back Panel Introduction .......................................................................................12

Step 5-2: ConnectorsIntroduction .............................................................................................13

Chapter 2 BIOS Setup ............................................................................................. 21

The Main Menu (For example: BIOS Ver. : F4c) ............................................................................21

StandardCMOSFeatures ................................................................................................................23

Advanced BIOS Features ................................................................................................................25

IntegratedPeripherals ........................................................................................................................26

PowerManagementSetup ................................................................................................................28

PnP/PCIConfigurations ....................................................................................................................30

PCI Health Status .............................................................................................................................31

Frequency/VoltageControl ................................................................................................................32

LoadFail-SafeDefaults ......................................................................................................................34

LoadOptimizedDefaults ....................................................................................................................34

SetSupervisor/User Password .......................................................................................................35

Save & Exit Setup ............................................................................................................................36

Exit Without Saving ...........................................................................................................................36

Chapter 3 Install Drivers ........................................................................................... 37

7VT600-RZ Series Motherboard

- 4 -

Chapter 1 Introduction

Features Summary

CPU

—

Socket A processor

AMD Athlon^TM/ Athlon^TMXP/ Duron^TM(K7)

128K L1 & 512K/256K/64K L2 cache on die

200/266/333/400MHz FSB

—

Supports 1.4GHz and faster

North Bridge: VIA KT600

Sourth Bridge: VIA VT8235

3 184-pin DDR sockets

Supports DDR DRAM PC2100/PC2700/PC3200

Supports up to 3.0GB DDR (Max)

Supports only 2.5V DDR DIMM

1 AGP slot supports 8X/4X mode(1.5V)

5 PCI slots supports 33M Hz & PCI 2.2 compliant

2 IDE controllers provides IDE HDD/CD-ROM (IDE1, IDE2)

with PIO, Bus M aster (Ultra DM A33/ATA66/ATA100/ATA133)

operation mode

Chipset

Memory

Slots

On-Board IDE

On-Board Floppy

On-Board Peripherals

—

Floppy port supports 2 FDD with 360K, 720K,1.2M, 1.44M and 2.88M bytes

1 Parallel port supports Norm al/EPP/ECP mode

2 Serial port (COM A & COM B)

6 x USB 2.0/1.1 (4 by cable)

PS/2 Keyboard interface and PS/2 Mouse interface

VIA VT6103L

On-Board LAN *

On-Board Sound

1 RJ45 port

Realtek ALC655 CODEC

Supports Jack Sensing function

Line Out / 2 front speaker

Line In / 2 rear speaker(by s/w switch)

M ic In / center & subwoofer(by s/w switch)

SPDIF Out /SPDIF In

CD In / AUX In / Game Port

Built in VIA VT8235 Chipset

Licensed Award BIOS

Supports Q-Flash

On-Board USB 2.0

BIOS

I/O Control

Hardware M onitor

IT8705

CPU/System Fan Revolution detect

CPU/System temperature detect

System voltage detect

CPU/System fan fail warning

Therm al shutdown function

" * " Support 7VT600-RZ only.

- 5 -

Introduction

Additional Features

—

PS/2 Keyboard power on by password,

PS/2 M ouse power on by double click

Exter nal M odem wake up

STR(Suspend-To-RAM)

AC Recovery

Poly fuse for keyboard over-current protection

USB KB/M ouse wake up from S3

Supports @BIOS

Supports EasyTune 4

Over Voltage (CPU/AGP/DDR/PCI) by BIOS

Over Clock (CPU/AGP/DDR/PCI) by BIOS

Overclocking

Form Factor

—

30.5cm x 20.0cm ATX size form factor, 4 layers PCB.

Please set theCPU host frequencyin accordance with your processor'sspecifications.

We don't recommend you to set the system bus frequency over the CPU's specification

becausethesespecificbus frequenciesare notthestandardspecificationsforCPU,chipsetand

mostof theperipherals. Whether your systemcan run under thesespecific busfrequencies

properlywill depend on yourhardware configurations,including CPU, Memory,Cards… etc.

7VT600-RZ Series Motherboard

- 6 -

7VT600-RZ Series Motherboard Layout

20.0 cm

CPU_FAN

KB_MS

ATX

SOCKETA

FDD

VIA KT600

AUDIO

AGP

CLR_CMOS

PCI1

BATTERY

VT6103L*

JP1

PCI2

PCI3

VT8 235

CODEC

SYS_FAN

PCI4

PCI5

SUR_CEN

IDE2

IDE1

IT8 705

BIOS

F_U SB1

F_U SB2

F_PANEL

AUX_IN

GAME

PWR_LED

SPDIF_IO

" * " Support 7VT600-RZ only.

- 7 -

Introduction

Block Diagram

CPUCLK+/- (100/133/166/200MHz)

AMD-K7^TM

AGP 4X/8X

System Bus100/133/166/200MHz

AGPCLK

(66MHz)

DDR RAM

HCLK+/- (100/133/166/200MHz)

GCLK(66MHz)

VIA

KT600

5 PCI

RJ45*

33 MHz

14.318 MHz

48 MHz

VIA

VT6103L*

VCLK(66MHz)

BIOS

VIA

Game Port

Floppy

VT8235

IT8705

LPT Port

24 MHz

33 MHz

2 COM

Ports

ATA66/100/133

6 USB

Ports

AC97

IDE Channels

CODEC

PCICLK

(33MHz)

PS/2 KB/Mouse

PCICLK (33MHz)

USBCLK (48MHz)

14.318 MHz

HCLK+/- (100/133/166/200MHz)

CPUCLK+/- (100/133/166/200MHz)

AGPCLK (66MHz)

CLK

GEN

33 MHz

V_Link (66MHz) / GCLK (66MHz)

" * " Support 7VT600-RZ only.

7VT600-RZ Series Motherboard

- 8 -

Hardware Installation Process

To set up your computer, you must complete the following steps:

Step 1- Set System Jum per (JP1)

Step 2- Install the Central Processing Unit (CPU)

Step 3- Install memory modules

Step 4- Install expansion cards

Step 5- Install I/O Peripherals cables

Step 3

Step2

Step 5

Step 4

Step 5

Step 1

Step 5

Step 1: Set System Jumper (JP1)

The system bus frequency can be switched at 100/133/166/200M Hz by adjusting system jumper (JP1).

(The internal frequency depend on CPU.)

Open: Auto

Close: 100MHz (Defualt)

JP1

1-2

CPU CLOCK

100MHz

Auto

Open

100MHz : Fix FSB 200M Hz CPU

Auto : Support FSB 266/333/400 MHz CPU

The "JP1" must set to "Auto" when you are using

FSB 266/333/400MHz CPU.

- 9 -

Hardware Installation Process

Step 2: Install the Central Processing Unit (CPU)

Before installing the processor, adhere to the following warning:

1. Please make sure the CPU type is supported by the motherboard.

2. The processor will overheat without the heatsink and/or fan, resulting in permanent

irreparable damage.

3. If you do not match the CPU socket Pin 1 and CPU cut edge well, it will cause

improper installation. Please change the insert orientation.

4. Apply therm al grease between the processor and cooling fan.

5. Never run the processor without the heatsink properly and firmly attached. Permanent

dam age will result.

6. Please set the CPU host frequency in accordance with your processor's specifications.

We don't recommend you to set the system bus frequency over the CPU's specification

because these specific bus frequencies are not the standard specifications for CPU,

chipset and most of the peripherals. Whether your system can run under these specific

bus frequencies properly will depend on your hardware configurations, including CPU,

Memory, Cards… etc.

Step 2-1: CPU Installation

SocketActuationLever

Figure 2.

Locate Pin 1 in the socket and look

for a (golden) cut edge on the CPU

upper corner. Insert the CPU into

the socket. (Do not force the CPU into the socket.) Then move the

socket lever to the locked position while holding pressure on the

center of the CPU.

Figure 1.

Pull the rod to the 90-degree

directly.

Step 2-2: CPU Cooling Fan Installation

Figure 1.

Figure 2.

Figure 3.

Apply the thermal tape(or grease) Fasten the cooling fan support-

to provide better heat conduction ing-base onto the CPU socket

between your CPU and cooling on the motherboard.

fan.

Make sure theCPU fan isplugged

to the CPU fan connector, than

the install completely.

7VT600-RZ Series Motherboard

- 10 -

Step 3: Install Memory Modules

Before installing the mem ory modules, adhere to the following warning:

1. When DIMM LED is ON, do not install / remove DIMM from socket.

2. Please note that the DIMM module can only fit in one direction dueto the one notch. Wrong

orientation will cause improper installation. Please change the insert orientation.

The motherboard has 3 dual inline mem ory module (DIMM) sockets. The BIOS will automatically detects

mem ory type and size. To install the mem ory m odule, just push it vertically into the DIMM socket. The

DIM M module can only fit in one direction due to the notch. Memory size can vary between sockets.

Notch

DDR

Support Unbuffered DDR DIMM Sizes type:

64 Mbit (2Mx8x4banks)

64 Mbit(1Mx16x4 banks)

256Mbit(8Mx8x4 banks)

512Mbit(8Mx16x4banks)

128Mbit(4Mx8x4 banks)

256Mbit(4Mx16x4banks)

128Mbit(2Mx16x4banks)

512Mbit(16Mx8x4banks)

Total System Memory (Max3GB)

1. The DIM M socket has a notch, so the DIM M

memory module can only fit in one direction.

2. Insert the DIM M m emory module vertically into

the DIMM socket. Then push it down.

3. Close the plastic clip at both edges of the DIMM

sockets to lock the DIMM module.

Reverse the installation steps when you wish to

remove the DIMM module.

- 11 -

Hardware Installation Process

Step 4: Install Expansion Cards

1. Read the related expansion card's instruction document before install the expansion card into

the com puter.

2. Please m ake sure your AGP card is AGP 4X/8X (1.5V).

AGP 4X/8X notch

3. Please carefully pull out the small white- drawable bar at the end of the AGP slot when you try to

install/ Uninstall the AGP card. Please align the AGP card to the onboard AGP slot and press firmly

down on the slot .M ake sure your AGP card is locked by the sm all white- drawable bar.

AGP Card

Step 5: Install I/O Peripherals Cables

Step 5-1: I/O Back Panel Introduction

{

}

PS/2 Keyboard and PS/2 Mouse connector

This connector supports standard PS/2 keyboard and PS/2 mouse.

Parallel port (LPT)

Device like printer can be connected to Parallel port.

w/x Serial ports (COMA / COMB)

Mouse and modem etc. can be connected to Serial port.

LAN port *

LAN is fast Ethernet with 10/100Mbps speed.

USB port

Before you connect your device(s) into USB connector(s), please make sure your device(s)

such as USB keyboard, mouse, scanner, zip, speaker...etc. Have a standard USB interface.

Also make sure your OS supports USB controller. If your OS does not support USB controller,

please contact OS vendor for possible patch or driver upgrade. For more information please

contact your OS or device(s) vendors.

" * " Support 7VT600-RZ only.

7VT600-RZ Series Motherboard

- 12 -

Line In jack

{

Devices like CD-ROM, walkman etc. can be connect to Line In jack.

Line Out jack

Connect the stereo speakers or earphone to this connector.

} MIC In jack

Microphone can be connect to MIC In jack.

After installation of the audio driver, you are able to use 2/4/6-channel audio feature by software

selection. You can connect "Front speaker" to "Line Out" jack, Connect "Rear speaker" to "Line In"

jack and connect "Center/Subwoofer" to "MIC In" jack.

Step 5-2: Connectors Introduction

1213 16

1) CPU_FAN

2) SYS_FAN

3) ATX (ATX Power)

4) IDE1 / IDE2

5) FDD

10) SUR_CEN

11) CD_IN

12) AUX_IN

13) SPDIF_IO

14) F_USB1 / F_USB2

15) GAME

6) PWR_LED

7) F_PANEL

8) BATTERY

9) F_AUDIO

16) CI (Case Open)

17) CLR_CMOS

- 13 -

Hardware Installation Process

1) CPU_FAN (CPU FAN Connector)

Please note, a proper installation of the CPU cooler is essential to prevent the CPU from running

under abnormal condition or damaged by overheating.The CPU fan connector supports Max.

current up to 600 mA.

Pin No.

Definition

GND

+12V

Sense

2) SYS_FAN (System FAN Connector)

This connector allows you to link with the cooling fan on the system case to lower the system

temperature.

Pin No.

Definition

GND

+12V

Sense

3) ATX (ATXPower Connector)

AC power cord should only be connected to your power supply unit after ATX power cable and

other related devices are firmly connected to the mainboard.

Pin No. Definition

1 0

2 0

3.3V

-12V

GND

VCC

PS_ON(soft on/off)

GND

-5V

VCC

GND

Power Good

5V SB (stand by +5V)

+12V

1 1

VCC

7VT600-RZ Series Motherboard

- 14 -

4) IDE1/ IDE2(IDE1/IDE2 Connector)

Please connect first harddisk to IDE1 and connect CDROM to IDE2. The red stripe of the ribbon

cable must be the same side with the Pin1.

3 9

IDE2

IDE1

4 0

5) FDD (Floppy Connector)

Please connect the floppy drive ribbon cables to FDD. It supports 360K,720K,1.2M,1.44M and

2.88Mbytes floppy disk types. The red stripe of the ribbon cable m ust be the same side with the

Pin1.

3 4

3 3

6) PWR_LED

PWR_LED is connect with the system power indicator to indicate whether the system is on/off. It

will blink when the system enters suspend mode. If you use dual color LED, power LED will turn

to another color.

Pin No.

Definition

MPD+

MPD-

- 15 -

Hardware Installation Process

7) F_PANEL (2 x 10 pins Connector)

Please connect the power LED, PC speaker, reset switch and power switch etc. of your chassis front

panel to the F_PANEL connector according to the pin assignm ent below.

Sp eaker Co nne ctor

Messa ge L ED/

Po we r/

Soft Po we r

Slee p LED

Con nector

2 0

1 9

Reset Switch

IDE Ha rd Disk Active LED

HD(IDEHard DiskActive LED)

SPK(SpeakerConnector)

Pin 1:LED anode(+)

Pin 2:LED cathode(-)

Pin1:VCC(+)

Pin2-Pin 3:NC

Pin4:Data(-)

RST(ResetSwitch)

Open:NormalOperation

Close:ResetHardwareSystem

Open:NormalOperation

Close:PowerOn/Off

Pin 1:LED anode(+)

Pin 2:LED cathode(-)

PW(SoftPowerConnector)

MPD(MessageLED/Power/

SleepLED)

8) BATTERY (Battery)

CAUTION

Danger of explosion if battery is incorrectly

replaced.

Replace only with the same or equivalent type

recommended by the manufacturer.

Dispose of used batteries according to the

manufacturer's instructions.

If you want to erase CM OS...

1. Turn off the computer and unplug the power cord.

2. Rem ove the battery, wait for 30 second.

3. Re-install the battery.

4. Plug the power cord and turn on the computer.

7VT600-RZ Series Motherboard

- 16 -

9) F_AUDIO (Front Audio Connector)

If you want to use Front Audio connector, you must remove 5-6, 9-10 Jumper.

In order to utilize the front audio header, your chassis must have front audio connector. Also please

make sure the pin assigment on the cable is the same as the pin assigment on the MB header. To find

out if the chassis you are buying support front audio connector, please contact your dealer. Please

note, you can have the alternative of using front audio connector or of using rear audio connector to

play sound.

Pin No.

Definition

MIC

GND

REF

Power

FrontAudio (R)

RearAudio (R)

Reserved

No Pin

FrontAudio (L)

RearAudio (L)

1 0

10) SUR_CEN (Surround Center Connector)

Please contact your nearest dealer for optional SUR_CEN cable.

Pin No.

Definition

SUROUTL

SUROUTR

GND

No Pin

CENTER_OUT

BASS_OUT

11) CD_IN (CD In Connector)

Connect CD-ROM or DVD-ROM audio out to the connector.

Pin No.

Definition

CD-L

GND

CD-R

- 17 -

Hardware Installation Process

12) AUX_IN ( AUX In Connector)

Connect other device (such as PCI TV Tunner audio out)to the connector.

Pin No.

Definition

AUX-L

GND

AUX-R

13) SPDIF_IO (SPDIF In/Out Connector)

The SPDIF output is capable of providing digital audio to external speakers or compressed AC3 data

to an external Dolby Digital Decoder. Use this feature only when your stereo system has digital input

and output function. Use SPDIF in feature only when your device has digital output function. Be

careful with the polarity of the SPDIF_IO connector. Check the pin assignment carefully while you

connect the SPDIF cable, incorrect connection between the cable and connector will m ake the

device unable to work or even damage it. For optional SPDIF cable, please contact your local

dealer.

Pin No.

Definition

VCC

No Pin

SPDIF

SPDIFI

GND

7VT600-RZ Series Motherboard

- 18 -

14) F_ USB1 / F_USB2 (Front USB Connector)

Be careful with the polarity of the F_USB connector. Check the pin assignment carefully while you

connect the F_USB cable, incorrect connection between the cable and connector will make the

device unable to work or even damage it. For optional F_USB cable, please contact your local

dealer.

Pin No.

Definition

Power

1 0

USB0DX-/USB2DX-

USB1Dy-/USB3 Dy-

USB0DX+/USB2DX+

USB1Dy+/USB3 Dy+

GND

No Pin

15) GAME (Game Connector)

This connector supports joystick, MIDI keyboard and other relate audio devices. Check the pin

assignment while you connect the game cables. Please contact your nearest dealer for optional

gam e cables.

Pin No.

Definition

VCC

Pin No.

Definition

GPSA1

GND

GRX1_R

GND

1 6

1 5

GPY1_R

VCC

GPSA2

VCC

GPSB1

MSO_R

GPSB2

No Pin

GPX2_R

GPY2_R

MSI_R

16) CI (Chassis Intrusion, Case Open)

This 2-pin connector allows your system to enable or disable the "case open" item in BIOS if the

system case begin rem ove.

Pin No.

Definition

Signal

GND

- 19 -

Hardware Installation Process

17) CLR_CMOS (Clear CMOS)

You may clear the CMOS data to its default values by this jumper. To clear CMOS, temporarily shor

1-2 pin. Default doesn't include the "Shunter" to prevent from improper use this jumper.

Short: Clear CMOS

Open: Normal

7VT600-RZ Series Motherboard

- 20 -

Chapter 2 BIOS Setup

BIOS Setup is an overview of the BIOS Setup Program. The program that allows users to modify the

basic system configuration. This type of inform ation is stored in battery-backed CMOS RAM so that it

retains the Setup information when the power is turned off.

ENTERING SETUP

Powering ON the com puter and pressing <Del> immediately will allow you to enter Setup. If you require

m ore advanced BIOS settings, please go to "Advanced BIOS" setting m enu. To enter

Advanced BIOS setting menu, press "Ctrl+F1" key on the BIOS screen.

CONTROL KEYS

>< >< ><

Move to select item

<Enter>

<Esc>

Select Item

Main M enu - Quit and not save changes into CMOS Status Page Setup Menu

and Option Page Setup Menu - Exit current page and return to Main M enu

Increase the numeric value or make changes

Decrease the num eric value or make changes

General help, only for Status Page Setup Menu and Option Page Setup M enu

Item Help

<+/PgUp>

<-/PgDn>

<F1>

<F2>

<F5>

<F6>

<F7>

Restore the previous CMOS value from CMOS, only for Option Page Setup Menu

Load the file-safe default CM OS value from BIOS default table

Load the Optimized Defaults

<F8>

Q-Flash utility

<F9>

System Inform ation

<F10>

Save all the CMOS changes, only for M ain Menu

MainMenu

The on-line description of the highlighted setup function is displayed at the bottom of the screen.

Status Page Setup Menu / Option Page Setup Menu

Press F1 to pop up a small help window that describes the appropriate keys to use and the possible

selections for the highlighted item . To exit the Help Window press <Esc>.

The Main Menu (For example: BIOS Ver. : F4c)

Once you enter Award BIOS CMOS Setup Utility, the Main Menu (as figure below) will appear on the

screen. The M ain Menu allows you to select from eight setup functions and two exit choices. Use

arrow keys to select among the items and press <Enter> to accept or enter the sub-menu.

}

Standard CMOS Features

Advanced BIOS Features

Integrated Peripherals

Power Management Setup

PnP/PCI Configurations

PC Health Status

Load Fail-Safe Defaults

Load Optimized Defaults

Set Supervisor Password

Set User Password

Save & Exit Setup

Exit Without Saving

Frequency/Voltage Control

ESC: Quit

higf: Select Item

F8: Q-Flash

F10: Save & Exit Setup

Time, Date, Hard Disk Type...

- 21 -

BIOS Setup

Ifyoucan'tfindthesettingyou want,pleasepress"Ctrl+F1"to searchthe advanced

optionhidden.

•

StandardCMOS Features

This setup page includes all the item s in standard com patible BIOS.

AdvancedBIOS Features

This setup page includes all the items of Award special enhanced features.

IntegratedPeripherals

This setup page includes all onboard peripherals.

PowerManagementSetup

This setup page includes all the items of Green function features.

PnP/PCI Configuration

This setup page includes all the configurations of PCI & PnP ISA resources.

PC Health Status

This setup page is the System auto detect Temperature, voltage, fan, speed.

Frequency/VoltageControl

This setup page is control CPU clock and frequency ratio.

LoadFail-Safe Defaults

Fail-Safe Defaults indicates the value of the system param eters which the system would be in safe

configuration.

•

LoadOptimized Defaults

Optimized Defaults indicates the value of the system parameters which the system would be in

best performance configuration.

Set Supervisor Password

Change, set, or disable password. It allows you to limit access to the system and Setup, or just

to Setup.

•

Set User Password

Change, set, or disable password. It allows you to lim it access to the system.

Save & Exit Setup

Save CMOS value settings to CM OS and exit setup.

Exit Without Saving

Abandon all CMOS value changes and exit setup.

7VT600-RZ Series Motherboard

- 22 -

Standard CMOS Features

Date (mm:dd:yy)

Time (hh:mm:ss)

Fri, Jan 9 2004

22:31:24

Item Help

Menu Level}

Change the day, month,

} IDE Primary Master

} IDE Primary Slave

} IDE Secondary Master

} IDE Secondary Slave

[None]

year

<Week>

Sun. to Sat.

Drive A

Drive B

Floppy 3 Mode Suport

[1.44M, 3.5"]

[None]

[Disabled]

<Month>

Jan. to Dec.

<Day>

1 to 31 (or maximum

allowed in the month)

Holt On

[All, But Keyboard]

Base Memory

Extended Memory

Total Memory

640K

127M

128M

<Year>

1999 to 2098

higf: Move Enter: Select

F5: Previous Values

+/-/PU/PD: Value F10: Save

F6: Fail-Save Default

ESC: Exit F1: General Help

F7: Optimized Defaults

FDate

The date form at is <week>, <month>, <day>, <year>.

8Week

8Month

8Day

The week, from Sun to Sat, determined by the BIOS and is display only

The month, Jan. Through Dec.

The day, from 1 to 31 (or the maximum allowed in the m onth)

The year, from 1999 through 2098

8Year

FTime

The tim es format in <hour> <minute> <second>. The time is calculated base on the 24-hour military-

tim e clock. For example, 1 p.m. is 13:00:00.

FIDE Primary Master, Slave / Secondary Master, Slave

The category identifies the types of hard disk from drive C to F that has been installed in the

computer. There are two types: auto type, and m anual type. Manual type is user-definable; Auto

type which will automatically detect HDD type.

Note that the specifications of your drive must match with the drive table. The hard disk will not work

properly if you enter improper information for this category.

If you select User Type, related information will be asked to enter to the following items. Enter the

information directly from the keyboard and press <Enter>. Such information should be provided in

the documentation form your hard disk vendor or the system m anufacturer.

8Capacity:

The hard disk size. The unit is Mega Bytes.

8Access Mode: The options are: Auto / Large / LBA / Normal.

8Cylinder:

8Head

The cylinder number of hard disk.

The read / Write head number of hard disk.

8Precomp

8Landing Zone

The cyliner number at which the disk driver changes the write current.

The cylinder number that the disk driver heads(read/write) are seated when

the disk drive is parked.

8SECTORS

The sector num ber of each track define on the hard disk.

If a hard disk has not been installed select NONE and press <Enter>.

- 23 -

BIOS Setup

FDrive A / Drive B

The category identifies the types of floppy disk drive A or drive B that has been installed in the

computer.

8None

No floppy drive installed

8360K, 5.25 “.

81.2M, 5.25 ”.

5.25 inch PC-type standard drive; 360K byte capacity.

5.25 inch AT-type high-density drive; 1.2M byte capacity

(3.5 inch when 3 Mode is Enabled).

8720K, 3.5 “.

81.44M, 3.5 “.

82.88M, 3.5 “.

3.5 inch double-sided drive; 720K byte capacity

3.5 inch double-sided drive; 1.44M byte capacity.

3.5 inch double-sided drive; 2.88M byte capacity.

FFloppy 3 Mode Support (for Japan Area)

8Disabled

8Drive A

8Drive B

8Both

Normal Floppy Drive. (Default value)

Enabled 3 mode function of Drive A.

Enabled 3 mode function of Drive B.

Drive A & B are 3 mode Floppy Drives.

FHalt on

The category determines whether the computer will stop if an error is detected during power up.

8NO Errors

The system boot will not stop for any error that may be detected

and you will be prompted.

8All Errors

Whenever the BIOS detects a non-fatal error the system will be stopped.

8All, But Keyboar The system boot will not stop for a keyboard error; it will stop for

all other errors. (Default value)

8All, But Diskette The system boot will not stop for a disk error; it will stop for all

other errors.

8All, But Disk/Key The system boot will not stop for a keyboard or disk error; it will

stop for all other errors.

Memory

The category is display-only which is determined by POST (Power On Self Test) of the BIOS.

BaseMemory

The POST of the BIOS will determ ine the amount of base (or conventional) memory

installed in the system.

The value of the base mem ory is typically 512 K for systems with 512 K memory

installed on the m otherboard, or 640 K for systems with 640 K or more memory

installed on the motherboard.

ExtendedMemory

The BIOS determines how much extended memory is present during the POST.

This is the amount of memory located above 1 M B in the CPU memory address

map.

7VT600-RZ Series Motherboard

- 24 -

Advanced BIOS Features

Item Help

Menu Level}

Select Boot Device

First Boot Device

Second Boot Device

Third Boot Device

[Floppy]

[HDD-0]

[CDROM]

priority

Password Check

[Setup]

[Floppy]

Boot from floppy

[LS120]

Boot from LS120

[HDD-0]

Boot from First HDD

[HDD-1]

Boot from Second HDD

higf: Move Enter: Select

F5: Previous Values

+/-/PU/PD: Value F10: Save

F6: Fail-Save Default

ESC: Exit F1: General Help

F7: Optimized Defaults

FFirst / Second / Third Boot device

M This feature allows you to select the boot device priority.

8Floppy

8LS120

8HDD-0~3

8SCSI

8CDROM

8LAN

8USB-CDROM

8USB-ZIP

8USB-FDD

8USB-HDD

8ZIP

Select your boot device priority by Floppy.

Select your boot device priority by LS120.

Select your boot device priority by HDD-0~3.

Select your boot device priority by SCSI.

Select your boot device priority by CDROM.

Select your boot device priority by LAN.

Select your boot device priority by USB-CDROM.

Select your boot device priority by USB-ZIP.

Select your boot device priority by USB-FDD.

Select your boot device priority by USB-HDD.

Select your boot device priority by ZIP.

8Disabled

Disabled this function.

F PasswordCheck

8System

The system can not boot and can not access to Setup page will be denied

if the correct password is not entered at the prompt.

8Setup

The system will boot, but access to Setup will be denied if the correct

password is not entered at the prom pt. (Default value)

- 25 -

BIOS Setup

Integrated Peripherals

[Enabled]

OnChip IDE Channel0

Item Help

OnChip IDE Channel1

AC97 Audio

[Enabled]

[Auto]

Menu Level u

VIA Onboard LAN *

USB 1.1 Controller

USB 2.0 Controller

USB Keyboard Support

USB Mouse Support

VIA LAN Boot ROM *

Onboard Serial Port 1

Onboard Serial Port 2

Onboard Parallel Port

UART Mode Select

[Enabled]

[Disabled]

[3F8/IRQ4]

[2F8/IRQ3]

[378/IRQ7]

[Normal]

[SPP]

Parallel Port Mode

Game Port Address

Midi Port Address

Midi Port IRQ

[201]

[330]

higf: Move Enter: Select

F5: Previous Values

+/-/PU/PD: Value F10: Save

F6: Fail-Save Default

ESC: Exit F1: General Help

F7: Optimized Defaults

F OnChip IDE Channel0

MWhen enabled, allows you to use the onboard primary PCI IDE. If a hard disk controller card is

used, set at Disabled.

8Enabled

8Disabled

Enable onboard 1st channel IDE port. (Default value)

Disable onboard 1st channel IDE port.

F OnChip IDE Channel1

MWhen enabled, allows you to use the onboard secondary PCI IDE. If a hard disk controller card

is used, set at Disabled.

8Enabled

8Disabled

Enable onboard 2nd channel IDE port. (Default value)

Disable onboard 2nd channel IDE port.

F AC97 Audio

8Enabled

BIOS will automatically detect onboard AC97 Audio. (Default value)

Disabled AC97 Audio.

8Disabled

F VIA Onboard LAN *

8Enabled

Enable VIA Onboard LAN function. (Default value)

Disable this function.

8Disabled

F USB 1.1 Controller

MDisable this option if you are not using the onboard USB feature.

8Enabled

Enabled USB Controller. (Default value)

8Disabled

Disabled USB Controller.

F USB 2.0 Controller

MDisable this option if you are not using the onboard USB 2.0 feature.

8Enabled

Enabled USB 2.0 Controller. (Default value)

8Disabled

Disabled USB 2.0 Controller.

" * " For 7VT600-RZ-C only.

7VT600-RZ Series Motherboard

- 26 -

F USB Keyboard Support

MWhen a USB keyboard is installed, please set at Enabled.

8Enabled

Enabled USB Keyboard Support.

8Disabled

Disabled USB Keyboard Support. (Default value)

F USB Mouse Support

8Enabled

Enabled USB M ouse Support.

8Disabled

Disabled USB Mouse Support. (Default value)

F VIA LAN Boot ROM *

This function decide whether to invoke the boot ROM of the onboard LAN chip.

8Disabled

Disable this function. (Default Value)

Enable this function.

8Enabled

F Onboard Serial Port 1

8Auto

BIOS will autom atically setup the port 1 address.

83F8/IRQ4

82F8/IRQ3

83E8/IRQ4

82E8/IRQ3

8Disabled

Enable onboard Serial port 1 and address is 3F8,Using IRQ4. (Default value)

Enable onboard Serial port 1 and address is 2F8,Using IRQ3.

Enable onboard Serial port 1 and address is 3E8,Using IRQ4.

Enable onboard Serial port 1 and address is 2E8,Using IRQ3.

Disable onboard Serial port 1.

F Onboard Serial Port 2

8Auto

BIOS will autom atically setup the port 2 address.

83F8/IRQ4

82F8/IRQ3

Enable onboard Serial port 2 and address is 3F8,Using IRQ4.

Enable onboard Serial port 2 and address is 2F8,Using IRQ3. (Default Value)

83E8/IRQ4

82E8/IRQ3

8Disabled

Enable onboard Serial port 2 and address is 3E8,Using IRQ4.

Enable onboard Serial port 2 and address is 2E8,Using IRQ3.

Disable onboard Serial port 2.

F OnBoard Parallel port

MThis feature allows you to select from a given set of param eters if the parallel port uses the

onboard I/O controller.

8378/IRQ7

8278/IRQ5

83BC/IRQ7

8Disabled

Enable onboard LPT port and address is 378, Using IRQ7.(Default Value)

Enable onboard LPT port and address is 278,Using IRQ5.

Enable onboard LPT port and address is 3BC,Using IRQ7.

Disable onboard parallel port.

F UART Mode Select

This item allows you to determine which Infra Red(IR) function of Onboard I/O chip.

Normal

IrDA

Set onboard I/O chip UART to Normal Mode. (Default Value)

Set onboard I/O chip UART to IrDA M ode.

ASKIR

SCR

Set onboard I/O chip UART to ASKIR Mode.

Set onboard I/O chip as Smart Card interface.

" * " For 7VT600-RZ-C only.

- 27 -

BIOS Setup

F Parallel Port Mode

MThis feature allows you to connect with an advanced print via the port mode it supports.

8SPP

8EPP

8ECP

8ECP+EPP

Using Parallel port as Standard Parallel Port using IRQ7. (Default Value)

Using Parallel port as Enhanced Parallel Port IRQ5.

Using Parallel port as Extended Capabilities Port using IRQ7.

Using Parallel port as ECP & EPP mode.

F Game Port Address

8Disabled

Disabled this function.

8201

8209

Set Gam e PortAddress to 201. (Default Value)

Set Game Port Address to 209.

F Midi Port Address

8Disabled

Disabled this function. (Default Value)

8300

8330

Set Midi Port Address to 300.

Set Midi Port Address to 330.

F Midi Port IRQ

Set 5 for M idi Port IRQ.

810

Set 10 for Midi Port IRQ.(Default value)

Power Management Setup

[S1(POS)]

ACPI Suspend Type

Item Help

x USB Device Wake-Up From S3

Power LED in S1 state

Soft-Off by PWRBTN

AC Back Function

Disabled

Menu Level u

[S1]

[Blinking]

[Instant-off]

[Soft-Off]

[Disabled]

[Enabled]

[Disabled]

Everyday

Set suspend type to

Power On Suspend under

ACPI OS

Keyboard Power On

Mouse Power On

[S3]

PME Event Wake Up

Set suspend type to

Suspend to RAM under

ACPI OS

ModemRingOn/WakeOnLAN

Resume by Alarm

x Date (of Month) Alarm

x Time (hh:mm:ss) Alarm

0 : 0 : 0

higf: Move Enter: Select

F5: Previous Values

+/-/PU/PD: Value F10: Save

F6: Fail-Save Default

ESC: Exit F1: General Help

F7: Optimized Defaults

7VT600-RZ Series Motherboard

- 28 -

F ACPI Suspend Type

8S1(POS)

Set suspend type to Power On Suspend under ACPI OS(Power On

Suspend). (Default value)

8S3(STR)

Set suspend type to Suspend To RAM under ACPI OS (Suspend To RAM).

F USB Device Wakeup From S3(When ACPI Suspend Type is set [S3(STR)])

USB device wakeup From S3 can be set when ACPI standby state set to S3/STR.

8Enabled

USB Device can wakeup system from S3.

8Disabled

USB Device can’t wakeup system from S3. (Default value)

F Power LED in S1 state

8Blinking

In standby m ode(S1), power LED will blink. (Default value)

8Dual/Off

In standby m ode(S1):

a. If use single color LED, power LED will turn off.

b. If use dual color LED, power LED will turn to another color.

F Soft-off by PWRBTN

8Instant-off

8Delay 4 Sec.

Press power button then Power off instantly. (Default value)

Press power button 4 sec to Power off. Enter suspend if button is pressed

less than 4 sec.

F ACBack Function

8Memory

8Soft-Off

8Full-On

System power on depends on the status before AC lost.

Always in Off state when AC back. (Default value)

Always power on the system when AC back.

F Keyboard Power On

This feature allows you to set the m ethod for powering-on the system.

The option "Password" allows you to set up to 8 alphanum eric characters to power-on the system.

The option "Keyboard 98" allows you to use the standard keyboard 98 to power on the system.

8Password

Enter from 1 to 8 characters to set the Keyboard Power On Password.

8Disabled

Disabled this function. (Default value)

8Keyboard 98

If your keyboard have "POWER Key" button, you can press the key to

power on your system .

F Mouse Power On

8Disabled

Can't Power on system by Mouse Event. (Default value)

Can Power on system by M ouse Event.

8Enabled

F PME Event Wake up

When set at Enabled, any PCI-PM event awakes the system from a PCI-PM controlled state.

This feature requires an ATX power supply that provides at least 1A on the +5VSB lead.

8Disabled

Disabled PM E Event Wake up function.

8Enabled

Enabled PME Event Wake up function. (Default Value)

- 29 -

BIOS Setup

F ModemRingOn/WakeOnLAN (When AC Back Function set to [Soft-Off])

You can enable wake on LAN feature by the "ModemRingOn/WakeOnLAN" or "PME Event Wake

up" when the M /B has "WOL" onboard connector. Only enabled the feature by "PME Event Wake

up". An incoming call via modem awakes the system from its soft-off m ode. When set at Enabled,

an input signal comes from the other client.

Server on the LAN awaks the system from a soft off state if connected over LAN.

8Disabled

Disabled Modem Ring On / Wake On LAN function.

8Enabled

Enabled Modem Ring On / Wake On LAN function. (Default Value)

F Resumeby Alarm

You can set "Resume by Alarm" item to enabled and key in Data/time to power on system.

8Disabled

Disable this function. (Default Value)

8Enabled

Enable alarm function to POWER ON system.

If RTC Alarm Lead To Power On is Enabled.

Date (of Month) Alarm :

Everyday, 1~31

Time (hh: m m: ss) Alarm : (0~23) : (0~59) : (0~59)

PnP/PCI Configurations

PCI1/PCI5 IRQ Assignment

[Auto]

Item Help

PCI2 IRQ Assignment

PCI3 IRQ Assignment

Menu Levelu

PCI4 IRQ Assignment

[Auto]

higf: Move Enter: Select

F5: Previous Values

+/-/PU/PD: Value F10: Save

F6: Fail-Save Default

ESC: Exit F1: General Help

F7: Optimized Defaults

7VT600-RZ Series Motherboard

- 30 -

F PCI1/PCI5 IRQ Assignment

8Auto

Auto assign IRQ to PCI 1/ PCI 5. (Default value)

Set 3,4,5,7,9,10,11,12,14,15 to PCI1/ PCI5.

83,4,5,7,9.,10,11,12,14,15

F PCI2 IRQ Assignment

8Auto

Auto assign IRQ to PCI 2. (Default value)

Set 3,4,5,7,9,10,11,12,14,15 to PCI2.

83,4,5,7,9.,10,11,12,14,15

F PCI3 IRQ Assignment

8Auto

Auto assign IRQ to PCI 3. (Default value)

Set 3,4,5,7,9,10,11,12,14,15 to PCI3.

83,4,5,7,9.,10,11,12,14,15

F PCI4 IRQ Assignment

8Auto

Auto assign IRQ to PCI 4. (Default value)

Set 3,4,5,7,9,10,11,12,14,15 to PCI4.

83,4,5,7,9.,10,11,12,14,15

PCI Health Status

PC Health Status

Reset Case Open Status

Case Opened

[Disabled]

Item Help

Menu Level u

Vcore

1.810V

1.248V

3.280V

4.919V

11.968V

5.053V

27^oC

DDR Vtt

[Disabled]

+3.3V

Don't reset case

open status

+5V

+12V

5VSB

[Enabled]

Current System Temperature

Current CPU Temperature

Current CPU FAN Speed

Current SYSTEM FAN Speed

CPU FAN Fail Warning

SYSTEM FAN Fail Warning

Clear case open

status at next boot

37^oC

4687 RPM

RPM

[Disabled]

higf: Move Enter: Select

F5: Previous Values

+/-/PU/PD: Value F10: Save

F6: Fail-Save Default

ESC: Exit F1: General Help

F7: Optimized Defaults

- 31 -

BIOS Setup

F Reset CaseOpen Status

F CaseOpened

If the case is closed, "Case Opened" will show "No".

If the case have been opened, "Case Opened" will show "Yes".

If you want to reset "Case Opened" value, set "Reset Case Open Status" to "Enabled" and save

CM OS, your computer will restart.

F Current Voltage (V) Vcore / DDR Vtt / +3.3V/ +5V / +12V / 5VSB

Detect system 's voltage status autom atically.

F CurrentSystem Temperature(°C)

Detect System Tem p. automatically.

F Current CPU Temperature (°C)

Detect CPU Temp. autom atically.

F Current CPU FAN / SYSTEM FAN Speed (RPM)

Detect Fan speed status automatically.

F Fan Fail Warning (CPU / SYSTEM)

8Disabled

8Enabled

Don't m onitor current fan speed. (Default value)

Alarm when stops.

Frequency/Voltage Control

Spread Spectrum Modulated

CPU Host Clock Control

øCPU Host Frequency(MHz)

øPCI/AGP Frequency(MHz)

[Enabled]

Item Help

[Disable]

133

33/66

Menu Level u

DRAM Clock(MHz)

CPU OverVoltage Control

[Auto]

AGP OverVoltage Control

DIMM OverVoltage Control

[Auto]

higf: Move Enter: Select

F5: Previous Values

+/-/PU/PD: Value F10: Save

F6: Fail-Save Default

ESC: Exit F1: General Help

F7: Optimized Defaults

øThose items will be available when "CPU Host Clock Control" is set to Enabled.

7VT600-RZ Series Motherboard

- 32 -

FSpreadSpectrum Modulated

8Disabled

8Enabled

Disable clock spread spectrum.

Enable clock spread spectrum.(Default value)

FCPU Host Clock Control

Note: If system hangs up before enter CMOS setup utility, wait for 20 sec for times out reboot . When

tim e out occur, system will reset and run at CPU default Host clock at next boot.

8Disable

Disable CPU Host Clock Control.(Default value)

8Enable

Enable CPU Host Clock Control.

FCPU Host Frequency (MHz) (By switch SW1)

8100

8133

8166

8200

Set CPU Host Clock to 100MHz~132M Hz.

Set CPU Host Clock to 133MHz~165M Hz.

Set CPU Host Clock to 166MHz~200M Hz.

Set CPU Host Clock to 200MHz~254M Hz.

FPCI/AGP Frequency(MHz)

8The values depend on CPU Host Frequency(Mhz) .

FDRAM Clock (MHz)

8Please set DRAM Clock according to your requirement. (Default value: Auto)

If you use DDR266 DRAM module, please set "DRAM Clock(MHz)" to "133-DDR266". If you use

DDR333 DRAM module, please set "DRAM Clock(MHz)" to "166-DDR333". If you use DDR400

DRAM module, please set "DRAM Clock(MHz)" to "200-DDR400".

Incorrect using it may cause your system broken. For power End-User use only!

FCPU OverVoltage Control

Increase CPU voltage m ay get stable for Over_Clock. But it may damage to CPU when enable this

feature.

8Auto

Supply voltage as CPU reguired. (Default value)

8+5% / +7.5% / +10% Increase voltage range as user selected.

FAGP OverVoltage Control

Increase AGP voltage may get stable for Over_Clock. But it may damage to AGP Card when enable this

feature.

8Auto

8+0.1V ~ +0.3V

Supply voltage as AGP Card reguired. (Default value)

Set AGP voltage from 1.6V~1.8V.

FDIMM OverVoltage Control

Increase DRAM voltage may get stable for Over_Clock. But it may dam age to DRAM m odule when

enable this feature.

8Auto

8+0.1V ~ +0.3V

Supply voltage as DRAM module reguired. (Default value)

Set DIMM voltage from 2.6V~2.8V.

- 33 -

BIOS Setup

Load Fail-Safe Defaults

}

Standard CMOS Features

Advanced BIOS Features

Integrated Peripherals

Power Management Setup

Load Fail-Safe Defaults

Load Optimized Defaults

Set Supervisor Password

Set User Password

PnP/PCI Configurations Load Fail-Safe DefaultSsav(eY/&N)E?xiNt Setup

PC Health Status

Exit Without Saving

Frequency/Voltage Control

ESC: Quit

higf: Select Item

F8: Q-Flash

F10: Save & Exit Setup

Load Fail-Safe Defaults

Fail-Safe defaults contain the m ost appropriate values of the system parameters that allow minim um

system performance.

Load Optimized Defaults

}

Standard CMOS Features

Advanced BIOS Features

Integrated Peripherals

Power Management Setup

PnP/PCI Configurations

PC Health Status

Load Fail-Safe Defaults

Load Optimized Defaults

Set Supervisor Password

Set User Password

Load Optimized Defaults (Y/N)? N

Save & Exit Setup

Exit Without Saving

Frequency/Voltage Control

ESC: Quit

higf: Select Item

F8: Q-Flash

F10: Save & Exit Setup

Load Optimized Defaults

Selecting this field loads the factory defaults for BIOS and Chipset Features which the system autom atically

detects.

7VT600-RZ Series Motherboard

- 34 -

Set Supervisor/User Password

}

Standard CMOS Features

Advanced BIOS Features

Integrated Peripherals

Power Management Setup

PnP/PCI ConfiguratEinotnesr Password:

PC Health Status

Load Fail-Safe Defaults

Load Optimized Defaults

Set Supervisor Password

Set User Password

Save & Exit Setup

Exit Without Saving

Frequency/Voltage Control

ESC: Quit

higf: Select Item

F8: Q-Flash

F10: Save & Exit Setup

Change/Set/Disable Password

When you select this function, the following message will appear at the center ofthe screen to assist you

in creating a password.

Type the password, up to eight characters, and press <Enter>. You will be asked to confirm the

password. Type the password again and press <Enter>. You may also press <Esc> to abort the

selection and not enter a password.

To disable password, just press <Enter> when you are prompted to enter password. A m essage

"PASSWORD DISABLED" will appear to confirm the password being disabled. Once the password is

disabled, the system will boot and you can enter Setup freely.

The BIOS Setup program allows you to specify two separate passwords:

SUPERVISOR PASSWORD and a USER PASSWORD. When disabled, anyone may access all BIOS

Setup program function. When enabled, the Supervisor password is required for entering the BIOS

Setup program and having full configuration fields, the User password is required to access only basic

items.

If you select "System " at "Password Check" in Advance BIOS Features Menu, you will be prom pted

for the password every time the system is rebooted or any tim e you try to enter Setup M enu.

If you select "Setup" at "Password Check" in Advance BIOS Features Menu, you will be prompted only

when you try to enter Setup.

- 35 -

BIOS Setup

Save & Exit Setup

}

Standard CMOS Features

Advanced BIOS Features

Integrated Peripherals

Power Management Setup

PnP/PCI Configurations

PC Health Status

Load Fail-Safe Defaults

Load Optimized Defaults

Set Supervisor Password

Set User Password

Save to CMOS and EXITSa(vYe/N&)?ExYit Setup

Exit Without Saving

Frequency/Voltage Control

ESC: Quit

higf: Select Item

F8: Q-Flash

F10: Save & Exit Setup

Save Data to CMOS

Type "Y" will quit the Setup Utility and save the user setup value to RTC CMOS.

Type "N" will return to Setup Utility.

Exit Without Saving

}

Standard CMOS Features

Advanced BIOS Features

Integrated Peripherals

Power Management Setup

PnP/PCI Configurations

PC Health Status

Load Fail-Safe Defaults

Load Optimized Defaults

Set Supervisor Password

Set User Password

Quit Without Saving S(aYv/eN)&? ENxit Setup

Exit Without Saving

Frequency/Voltage Control

ESC: Quit

higf: Select Item

F8: Q-Flash

F10: Save & Exit Setup

Abandon all Data

Type "Y" will quit the Setup Utility without saving to RTC CM OS.

Type "N" will return to Setup Utility.

7VT600-RZ Series Motherboard

- 36 -

Revision History

Chapter 3 Install Drivers

Install Drivers

Picture below are shown inWindows XP

Insert the driver CD-title that came with your motherboard into your CD-ROM drive, the

driver CD-title will auto start and show the installation guide. If not, please double click the

CD-ROM device icon in "My com puter", and execute the setup.exe.

INSTALL CHIPSET DRIVER

This page shows the drivers that need to be installed for the system. Click each item to install the driver

manually or switch to the

to install the drivers automatically.

The "Xpress Install" uses the"Click and GO" technology to install the drivers automatically. Just select the

drivers you want then click the "GO" button. The

will finish the installation for you automatically.

Massage: Some device drivers will restart

your system automatically. After restarting

your system the "Xpress Install" will

continue to install other drivers.

We recommend that you install all com ponents in the list.

- 37 -

Driver Installation

Driver install finished !

You have to reboot system !

Item Description

VIA 4IN1 Driver

For INF, AGP, IDE and DM A Driver

USB Path for WinXP

This patch driver can help you to resolve the USB device wake up S3 hang up issue in XP

VIA Lan Driver *

VIA 10/100 LAN driver for VT6103L chips

RealTek AC97 Audio Driver

Audio driver for Realtek AC97 codec chipset

VIA USB 2.0 Controller

USB 2.0 Driver information for XP

For USB2.0 driver support under Windows XP operating system, please use Windows

Service Pack. After install Windows Service Pack, it will show a question mark "?" in

"Universal Serial Bus controller" under "Device Manager". Please remove the question mark

and restart the system (System will auto-detect the right USB2.0 driver).

" * " For 7VT600-RZ-C Only.

7VT600-RZ Series Motherboard

- 38 -

- 39 -

Driver Installation

Contactus via the information in this page all over the world.

— Taiwan

— The Netherlands

Gigabyte TechnologyCo., Ltd.

Address:No.6, Bau Chiang Road, Hsin-Tien, Taipei Hsien,

Taiwan,R.O.C.

Giga-ByteTechnologyB.V.

Address:Verdunplein8 5627 SZ,Eindhoven,The Netherlands

Tel:+3140 2902088

Tel:886 (2)8912-4888

Fax:886(2)8912-4004

Tech.Support:

NLTech.Support:0900-GIGABYTE(0900-44422983, 0.2/M)

BETech.Support:0900-84034 ( 0.4/M)

Fax:+31 40 290 2089

http://tw.giga-byte.com/TechSupport/ServiceCenter.htm

Non-Tech.Support(Sales/Marketingissues):

http://ggts.gigabyte.com.tw/nontech.asp

Website:http://www.gigabyte.com.tw

Tech.Support:

http://nz.giga-b y t e.com/TechSupport /Servi c eCenter.htm

Non-Tech.Support(Sales/Marketingissues):

http://ggts.gigabyte.com.tw/nontech.asp

Website:http://www.giga-byte.nl

— China

—

USA

G.B.T.INC.

Address:17358 Railroad St, CityofIndustry, CA91748.

Tel:1(626)854-9338

NINGBOG.B.T. Tech.Trading CO., Ltd.

Tech.Support:

Fax:1(626)854-9339

Tech.Support:

http://cn.giga-byte.com/TechSupport/ServiceCenter.htm

Non-Tech.Support(Sales/Marketingissues):

http://ggts.gigabyte.com.tw/nontech.asp

Website:http://www.gigabyte.com.cn

Beijing

http://www.giga-byte.com/TechSupport/ServiceCenter.htm

Non-Tech.Support(Sales/Marketingissues):

http://ggts.gigabyte.com.tw/nontech.asp

Website:http://www.giga-byte.com

— Germany

Tel:86-10-82856054,86-10-82856064,86-10-82856094

Fax:86-10-82856575

G.B.T.TechnologyTradingGmbH

Tel:49-40-2533040

Chengdu

Tel:86-28-85236930

49-01803-428468 (Tech.)

Fax:86-28-85256822

Fax:49-40-25492343(Sales)

49-01803-428329 (Tech.)

GuangZhou

Tel:86-20-87586273

Tech.Support:

Fax:86-20-87544306

http://de.giga-byte.com/TechSupport/ServiceCenter.htm

Non-Tech.Support(Sales/Marketingissues):

http://ggts.gigabyte.com.tw/nontech.asp

Website:http://www.gigabyte.de

Shanghai

Tel:86-21-64737410

Fax:86-21-64453227

Shenyang

—

Japan

Tel:86-24-23960918,86-24-23960893

Wuhan

NipponGiga-ByteCorporation

Website:http://www.gigabyte.co.jp

Tel:86-27-87854385,86-27-87854802

Fax:86-27-87854031

Xian

Tel:86-29-5531943

Fax:86-29-5539821

—

U.K

G.B.T. TECH.CO. LTD.

Tel:44-1908-362700

Fax:44-1908-362709

Tech.Support:

http://uk.giga-byte.com/TechSupport/ServiceCenter.htm

Non-Tech.Support(Sales/Marketingissues):

http://ggts.gigabyte.com.tw/nontech.asp

Website:http://uk.giga-byte.com

7VT600-RZ Series Motherboard

- 40 -

EVGA 123 CD E635 User Manual
Elo TouchSystems ET1529L User Manual
Electrolux Thermaline WLXWCBOOOO User Manual
Eizo Nanao Computer Monitor FS2332 User Manual
Cypress CY7C1157V18 User Manual
Black Box CAT5 User Manual
AT T E2812B User Manual
Asus LSISAS1064E User Manual
Adesso WKB 4000UB User Manual
Acer X213H User Manual