Foster e 7370 230 User Manual

USER'S MANUAL FOR S3000 INDUCTION HOBS  
cod. 7331 230 e 7370 230  
SAFETY  
Precautions before using  
Unpack all the materials.  
The installation and connecting of the appliance have to be done by approved specialists.  
The manufacturer can not be responsible for damage caused by building-in or connecting  
errors.  
To be used, the appliance must be well-equipped and installed in a kitchen unit and an  
adapted and approved work surface.  
This domestic appliance is exclusively for the cooking of food, to the exclusion of any other  
domestic, commercial or industrial use.  
Remove all labels and self-adhesives from the ceramic glass.  
Do not change or alter the appliance.  
The cooking plate can not be used as freestanding or as working surface.  
The appliance must be grounded and connected conforming to local standards.  
Do not use any extension cable to connect it.  
The appliance can not be used above a dishwasher or a tumble-dryer: steam may damage  
the electronic appliances.  
Using the appliance  
Switch the heating zones off after using.  
Keep an eye on the cooking using grease or oils: that may quickly ignite.  
Be careful not to burn yourself while or after using the appliance.  
Make sure no cable of any fixed or moving appliance contacts with the glass or the hot  
saucepan.  
Magnetically objects (credit cards, floppy disks, calculators) should not be placed near to  
the engaged appliance.  
Metallic objects such as knives, forks, spoons and lids should not be placed on the hob  
surface since they can get hot.  
In general do not place any metallic object except heating containers on the glass surface.  
In case of untimely engaging or residual heat, this one may heat, melt or even burn.  
Never cover the appliance with a cloth or a protection sheet. This is supposed to become  
very hot and catch fire.  
This appliance is not intended for use by persons (including children) with reduced  
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they  
have been given supervision or instruction concerning use of the appliance by a person  
responsible for their safety.  
Children should be supervised to ensure that they do not play with the appliance.  
17  
Precautions not to damage the appliance  
Raw pan bottoms or damaged saucepans (not enamelled cast iron pots,) may damage the  
ceramic glass.  
Sand or other abrasive materials may damage ceramic glass.  
Avoid dropping objects, even little ones, on the vitroceramic.  
Do not hit the edges of the glass with saucepans.  
Make sure that the ventilation of the appliance works according to the manufacturer’s  
instructions.  
Do not put or leave empty saucepans on the vitroceramic hobs.  
Sugar, synthetic materials or aluminium sheets must not contact with the heating zones.  
These may cause breaks or other alterations of the vitroceramic glass by cooling: switch  
on the appliance and take them immediately out of the hot heating zone (be careful: do not  
burn yourself).  
Never place any hot container over the control panel.  
If a drawer is situated under the embedded appliance, make sure the space between the  
content of the drawer and the inferior part of the appliance is large enough (2 cm). This is  
essential to guaranty a correct ventilation.  
Never put any inflammable object (ex. sprays) into the drawer situated under the  
vitroceramic hob. The eventual cutlery drawers must be resistant to heat.  
Precautions in case of appliance failure  
If a defect is noticed, switch on the appliance and turn off the electrical supplying.  
If the ceramic glass is cracked or fissured, you must unplug the appliance and contact the  
after sales service.  
Repairing has to be done by specialists. Do not open the appliance by yourself.  
WARNING: If the surface is cracked, switch off the appliance to avoid the possibility of  
electric shock.  
Other protections  
Note sure that the container pan is always centred on the cooking zone. The bottom of  
the pan must have to cover as much as possible the cooking zone.  
For the users of pacemaker, the magnetic field could influence its operating. We  
recommend getting information to the retailer or of the doctor.  
Do not to use aluminium or synthetic material containers: they could melt on still hot  
cooking zones.  
DO NOT USE INTERMEDIATE REMOVABLE ACCESSORIES TO HEAT  
PANS WHICH ARE NOT ADAPTED TO INDUCTION.  
RISKS OF BURNS AND DETERIORATION OF THE HOB.  
18  
DESCRIPTION OF THE APPLIANCE  
Technical characteristics  
Position of the  
heating zone  
Nominal  
Power*  
Booster  
Power*  
Type  
Total Power  
6000 W  
Diameter  
Front left  
Rear left  
Right  
2000 W  
1200 W  
2000 W  
2300 W  
1400 W  
2300 W  
200 mm  
180 mm  
250 mm  
7331230  
Front left  
Rear left  
Rear right  
Front right  
2000 W  
1200 W  
2000 W  
1200 W  
2300 W  
1400 W  
2300 W  
1400 W  
200 mm  
180 mm  
220 mm  
150 mm  
7370230  
7400 W  
* The given power may change according to the dimensions and material of the pan.  
Control panel  
Timer display  
Control light timer  
Power display  
[ - ] key for all 3 / 4  
heating zones  
Control light cooking zone  
[ + ] key  
Timer key  
Booster  
key  
On/Off key  
19  
USE OF THE APPLIANCE  
Display  
Display  
0
1…9  
U
A
E
H
P
L
Designation  
Zero  
Function  
The heating zone is activated.  
Selection of the cooking level.  
No pan or inadequate pan.  
Automatic cooking.  
Power level  
Pan detection  
Heat accelerator  
Error message  
Residual heat  
Booster  
Electronic failure.  
The heating zone is hot.  
The boosted power is activated.  
Control panel locking.  
Locking  
Ventilation  
The cooling system is fully automatic. The cooling fan starts with a low speed when the calories  
brought out by the electronic system reach a certain level. The ventilation starts his high speed  
when the hob is intensively used. The cooling fan reduces his speed and stops automatically  
when the electronic circuit is cooled enough.  
STARTING-UP AND APPLIANCE MANAGEMENT  
Before the first use  
Clean your hob with a damp cloth, and then dry the surface thoroughly. Do not use detergent  
which risks causing blue-tinted colour on the glass surface.  
Induction principle  
An induction coil is located under each heating zone. When it is engaged, it produces a variable  
electromagnetic field which produces inductive currents in the ferromagnetic bottom plate of the  
pan. The result is a heating-up of the pan located on the heating zone.  
Of course the pan has to be adapted:  
All ferromagnetic pans are recommended (please verify it thanks a little magnet): cast iron  
and steel pans, enamelled pans, stainless-steel pans with ferromagnetic bottoms…  
Are excluded: cupper, pure stainless-steel, aluminium, glass, wood, ceramic, stoneware,…  
The induction heating zone adapts automatically the size of the pan. With a too small diameter  
the pan doesn’t work. This diameter is varying in function of the heating zone diameter.  
If the pan is not adapted to the induction hob the display will show [ U ].  
Sensitive touch  
Your ceramic hob is equipped with electronic controls with sensitive touch keys. When your finger  
presses the key, the corresponding command is activated. This activation is validated by a  
control light, a letter or a number in the display and/or a “beep” sound.  
In the case of a general use press only one key at the same time.  
20  
Starting-up  
You must first switching on the hob, then the heating zone :  
Start-up/ switch off the hob :  
Action  
Control panel  
Display  
To start  
Touch the key  
Press key [  
Press key [  
]
]
3 or 4 x [ 0 ]  
Nothing or [ H ]  
Start-up/ switch off a heating zone :  
Action  
Control panel  
Display  
Zone selection  
Increase power  
Press key [ + ] from the zone  
Press key [ + ] or [ - ]  
[ 0 ]  
[ 1 ] to [ 9 ]  
Decrease power  
Stop  
Press key [ - ]  
Press simultaneous [ + ] and [ - ]  
or press keys [ - ]  
[ 9 ] to [ 1 ]  
[ 0 ] or [ H ]  
[ 0 ] or [ H ]  
If no action is made within 20 second the electronics returns in waiting position.  
Pan detection  
The pan detection ensures a perfect safety.  
The induction doesn’t work :  
If there is no pan on the heating zone or if this pan is not adapted to the induction. In this  
case it is impossible to increase the power and the display shows [ U ]. This symbol  
disappears when a pan is put on the heating zone.  
If the pan is removed from the heating zone the operation is stopped. The display shows  
[U]. The symbol [ U ] disappears when the pan is put back to the heating zone. The  
cooking continues with the power level set before.  
Residual heat indication  
After the switch off of a heating zone or the complete stop of the hob, the heating zones are still  
hot and indicates [ H ] on the display.  
The symbol [ H ] disappears when the heating zones may be touched without danger.  
As far as the residual heat indicators are on light, don’t touch the heating zones and don’t put  
any heat sensitive object on them . There are risks of burn and fire.  
21  
Booster function  
The booster function [ B ] grants a boost of power to the selected heating zone.  
If this function is activated the heating zones works during 10 minutes with an ultra high power.  
The booster is foreseen for example to heat up rapidly big quantities of water, like for noodles  
cooking.  
Start up / Stop the booster function :  
Action  
Control panel  
Display  
Zone selection  
Press key [ + ] from the zone  
Press key [ + ] or [ - ]  
Press key [ B ]  
Press key [ - ]  
or press key [ B ]  
[ 0 ]  
[ 1 ] to [ 9 ]  
[ P ] during 10 min  
[ 9 ]  
[ 9 ]  
Increase power  
Start up the booster  
Stop the booster  
The booster function [ B ] can also be started directly :  
Action  
Control panel  
Display  
Zone selection  
Start up the booster  
Stop the booster  
Press key [ + ] from the zone  
Press key [ B ]  
Press key [ - ]  
[ 0 ]  
[ P ] during 10 min  
[ 9 ]  
[ 9 ]  
or press key [ B ]  
Power management :  
The whole cooking hob is equipped by a maximum of power. When the booster function is  
activated, and not to exceed the maximum power, the electronic system orders to reduce  
automatically the power level of an other heating zone. The display is blinking on [ 9 ] during a  
few seconds and then shows the maximum of power allowed ( [ 6 ] or [ 8 ] ).  
Heating zone selected  
[ P ] is displayed  
The other heating zone: (example: power level 9)  
[ 9 ] goes to [ 7 ] or [ 8 ] depending the type of zone  
Timer  
The timer is able to be used simultaneous with all 3 or 4 heating zones and this with different time  
settings (from 0 to 99 minutes) for each heating zone.  
Setting and modification of the cooking time :  
Action  
Control panel  
Display  
Zone selection  
Increase power  
Press key [ + ] from the zone  
Press key [ + ] or [ - ]  
[ 0 ]  
[ 1 ] to [ 9 ]  
To select « Timer »  
Decrease the time  
Increase the time  
Press key [  
Press key [ - ]  
Press key [  
]
Timer [ 00 ] min  
[ 00 ] goes to 60,59…  
The time increases  
]
After a few seconds the control light stops with blinking.  
The time is confirmed and the cooking starts until the time reaches [ 00 ].  
22  
To stop the cooking time :  
Action Control panel  
Press key [ + ] from the zone  
Press key [  
Display  
Zone selection  
To select « Timer »  
To stop the « Timer »  
[ 0 ]  
]
The remaining time  
[ 00 ] then stops  
Press key [ - ] and [  
simultaneously  
]
If several timers are activated repeat the process.  
Automatic stop at the end of the cooking time :  
As soon as the selected cooking time is finished the timer displays blinking [ 00 ] and a sound rings.  
To stop the sound and the blinking it is enough to press the key [ ].  
Egg timer function :  
Action  
Control panel  
Display  
Activate the hob  
Select« Timer »  
Decrease the time  
Increase the time  
Press key [  
Press key [  
Press key [ - ]  
Press key [  
]
]
3 or 4 x [ 0 ] or [ H ]  
Timer [ 00 ] min  
[ 00 ] wents to 60,59…  
The time increases  
]
After a few seconds the control light stops with blinking.  
As soon as the selected cooking time is finished the timer displays blinking [ 00 ] and a sound rings.  
To stop the sound and the blinking it is enough to press the key [ ].  
Automatic cooking  
All the cooking zones are equipped with an automatic “go and stop” cooking device. The cooking  
zone starts at full power during a certain time, then reduces automatically its power on the  
preselected level.  
Start-up :  
Action  
Control panel  
Display  
Zone selection  
Press key [ + ] from the zone  
Repress key [ + ]  
Repress key [ + ]  
[ 0 ]  
[ 1 ] to [ 9 ]  
[ 9 ] is blinking with [A]  
[ 9 ] wents to [ 8 ] [ 7 ]  
[ 7 ] is blinking with [A]  
Full power setting  
Automatic cooking  
Power level selection  
(for example « 7 »)  
Press key [ - ]  
Switching off the automatic cooking :  
Action  
Control panel  
Display  
Zone selection  
Press key [ + ] from the zone  
[ 7 ] is blinking with [A]  
(for example « 7 »)  
Power level selection  
Press key [ - ] or [ + ]  
Level selected  
23  
Control panel locking  
To avoid modifying a setting of cooking zones , in particular with within the framework of cleaning  
the control panel can be locked (with exception to the On/Off key [ ]).  
Locking :  
Action  
Control panel  
Display  
Start  
Press key [  
]
3 or 4 x [ 0 ] or [ H ]  
Hob locking  
Press simultaneously [ - ] and [ + ]  
at front right**  
No modification  
3 or 4 x [ L ]  
Repress key [ + ]  
Unlocking :  
Action  
Control panel  
Display  
Start  
Press key [  
]
3 or 4 x [ L ]  
In the 5 seconds after start :  
Unlocking the hob  
Press simultaneously [ - ] and [ + ]  
at front right**  
3 or 4 x [ 0 ]  
No light on the  
Displays  
Repress key [ - ]  
** for the 3 zone hob use [ + ] from the front left zone display  
COOKING ADVICES  
Pan quality  
Adapted materials : steel, enamelled steel, cast iron, ferromagnetic stainless-steel,  
aluminium with ferromagnetic bottom.  
Not adapted materials : aluminium and stainless-steel without ferromagnetic bottom,  
cupper, brass, glass, ceramic, porcelain.  
The manufacturers specify if their products are compatible induction.  
To check if pans are compatibles :  
Put a little water in a pan placed on an induction heating zone set at level [ 9 ].This water  
must heat in a few seconds.  
A magnet stucks on the bottom of the pan.  
Certain pans can make noise when they are placed on an induction cooking zone. This noise  
doesn’t mean any failure on the appliance and doesn’t influence the cooking operating.  
Pan dimension  
The cooking zones are, until a certain limit, automatically adapted to the diameter of the pan.  
However the bottom of this pan must have a minimum of diameter according to the  
corresponding cooking zone.  
To obtain the best efficiency of your hob, please place the pan well in the centre of the cooking  
zone.  
24  
Examples of cooking power setting  
(the values below are indicative)  
1 to 2  
Melting  
Sauces, butter, chocolate, gelatine  
Dishes prepared beforehand  
Rice, pudding, sugar syrup  
Dried vegetables, fish, frozen products  
Vegetables, fish, meat  
Reheating  
Simmering  
Defrosting  
Steam  
2 to 3  
3 to 4  
4 to 5  
Water  
Steamed potatoes, soups, pasta,  
fresh vegetables  
6 to 7  
Medium cooking  
Simmering  
Meat, lever, eggs, sausages  
Goulash, roulade, tripe  
7 to 8  
9
Cooking  
Potatoes, fritters, wafers  
Steaks, omelettes, fried dishes  
Water  
scallops, steaks  
Boiling significant quantities of water  
Frying, roosting  
Boiling water  
Frying, roosting  
Boiling water  
P
MAINTENANCE AND CLEANING  
Switch-off the appliance before cleaning.  
Do not clean the hob if the glass is too hot because they are risk of burn.  
Remove light marks with a damp cloth with washing up liquid diluted in a little water. Then  
rinse with cold water and dry the surface thoroughly.  
Highly corrosive or abrasive detergents and cleaning equipment likely to cause scratches  
must be absolutely avoided.  
Do not ever use any steam-driven or pressure appliance.  
Do not use any object that may scratch the ceramic glass.  
Ensure that the pan is dry and clean. Ensure that there are no grains of dust on your  
ceramic hob or on the pan. Sliding rough saucepans will scratch the surface.  
Spillages of sugar, jam, jelly, etc. must be removed immediately. You will thus prevent the  
surface being damaged.  
25  
WHAT TO DO IN CASE OF A PROBLEM  
The symbol [ E 4 ] displays :  
The hob must be configured according to the following procedure.  
I) Warning : before starting all pots must be removed from the cooktop.  
II) Disconnect the cooktop from the main supply : remove fuse or disconnect circuit breaker.  
III) Connect the cooktop to the main supply : replace the fuse or connect the circuit breaker.  
IV) Procedure : You must provide yourself with a ferromagnetic bottom container 16 cm  
minimum diametre.  
* start within 2 minutes after the connection to the main supply  
* do not use the [ O/I ] key.  
V) How to cancel the existing configuration :  
1) 7331230 : Push on key [ - ] and keep your finger on  
the key  
7370230 : Push on key [ 1 ] and keep your finger on  
the key  
c
d
b
a
2) With a finger from the other hand : activate anti-  
clockwise successively and quickly all other existing  
[ + ] keys. Start with the front right cooking zone and  
move anti-clockwise (a -> b -> c -> d). A double "beep"  
sound will inform you of a bad manipulation and you  
will have to restart from point 1.  
3) Take your fingers off the touches and re-touch and hold down [ - ] for a few  
seconds, until blinking [ E ] appears.  
4) Wait until [ E ] becomes permanent.  
5) The [ E ] will be transformed automatically into [ C ]. The configuration has been  
done.  
Nota : Cooktops with 3 heating zones : Start the procedure with the rear right [ + ]  
key (b) ( the front right zone doesn't exist...)  
VI) How to configure the hob ?  
1) Use a suitable induction pot with a minimum diametre size of 16cm.  
2) Select the heating zone by pushing the corresponding [ + ] key.  
3) Put the pot on the corresponding heating zone.  
4) Wait until [ C ] converts to [ - ]. The zone is configured  
5) Use the same procedure for each other heating zone which displays [ C ]  
6) The configuration is made if all zones are detected and if nothing is displayed  
Use only 1 pot to configure the hob.  
Never put two or more pots on the heating zones during the configuration.  
If [ E 4 ] display persists call the After-sales Service  
The hob or the cooking zone doesn’t start-up :  
The hob is badly connected on the electrical network.  
The protection fuse cut-off.  
The looking function is activated.  
The sensitive keys are covered of grease or water.  
An object is put on a key.  
The control panel displays [ U ]:  
There is no pan on the cooking zone.  
The pan is not compatible with induction.  
The bottom diameter of the pan is too small.  
26  
The control panel displays [ C ] or [ E ] :  
Call the After-sales Service.  
One or all cooking zone cut-off :  
The safety system functioned.  
You forgot to cut-off the cooking zone for a long time.  
One or more sensitive keys are covered.  
The pan is empty and its bottom overheated.  
The hob also has an automatic reduction of power level and breaking Automatic overheating  
Continuous ventilation after cutting off the hob :  
This is not a failure, the fan continuous to protect the electronic device.  
The fan cooling stops automatically.  
The automatic cooking system doesn’t start-up :  
The cooking zone is still hot [ H ].  
The highest power level is set [ 9 ].  
The control panel displays [ L ] :  
Refer to the chapter control panel locking page.  
ENVIRONMENT PRESERVATION  
The materials of packing are ecological and recyclable.  
The electronic appliances are composed of recyclable, and sometimes harmful materials  
for the environment, but necessary to the good running and the safety of the appliance.  
Don't throw your appliance with the household refuses  
Get in touch with the waste collection centre of your  
commune that is adapted to the recycling of  
the household appliances.  
27  
INSTALLATION INSTRUCTIONS  
The installation comes under the exclusive responsibility of specialists.  
The installer is held to respect the legislation and the standards enforce in his home country.  
How to stick the gasket:  
The gasket supplied with the hob avoids all infiltration of liquids in the cabinet.  
His installation has to be done carefully, in conformity of the following drawing.  
Stick the gasket (2) two millimeters  
from the external edge of the glass,  
after removing the protection sheet (3).  
Fitting - installing:  
The cut out sizes are:  
Reference  
7331230  
7370230  
Cut-size  
560 x 490 mm  
560 x 490 mm  
Ensure that there is a distance of 50 mm between the hob and the wall or sides.  
The hobs are classified as “Y” class for heat protection. Ideally the hob should be installed  
with plenty of space on either side. There may be a wall at the rear and tall units or a wall  
at one side. On the other side, however, no unit or divider must stand higher than  
the hob.  
The piece of furniture or the support in which the hob is to be fitted, as well as the edges of  
furniture, the laminate coatings and the glue used to fix them, must be able to resist  
temperatures of up to 100 °C.  
The mural rods of edge must be heat-resisting.  
Not to install the hob to the top of a not ventilated oven or a dishwasher.  
To guarantee under the bottom of the hob casing a space of 20 mm to ensure a good air  
circulation of the electronic device.  
If a drawer is placed under the work, avoid to put into this drawer flammable objects  
(for example: sprays) or not heat-resistant objects.  
Materials which are often used to make worktops expand on contact with water. To protect  
the cut out edge, apply a coat of varnish or special sealant. Particular care must be given  
to applying the adhesive joint supplied with the hob to prevent any leakage into the  
supporting furniture. This gasket guaranties a correct seal when used in conjunction with  
smooth work top surfaces.  
The safety gap between the hob and the cooker hood placed above must respect the  
indications of the hood manufacturer. In case of absence of instructions respect a distance  
minimum of 760 mm.  
The connection cord should be subjected, after building, with no mechanical constraint,  
such for example of the fact of the drawer.  
28  
ELECTRICAL CONNECTION  
The installation of this appliance and the connection to the electrical network should be  
entrusted only to an electrician perfectly to the fact of the normative regulations and which  
respects them scrupulously.  
Protection against the parts under tension must be ensured after the building-in.  
The data of connection necessary are on the stickers place on the hob casing near the  
connection box.  
The connection to the main must be made using an earthed plug or via an omnipolar  
circuit breaking device with a contact opening of at least 3 mm.  
The electrical circuit must be separated from the network by adapted devices, for example:  
circuit breakers, fuses or contactors.  
Caution!  
This appliance has only to be connected to a network 230 V~ 50/60 Hz.  
Connect always the earth wire.  
Respect the connection diagram.  
The connection box is located underneath at the back of the hob casing. To open the cover use a  
medium screwdriver. Place it in the slits and open the cover.  
Mains  
Connection  
1 Phase + N  
Cable diameter  
3 x 2,5 mm²  
Cable  
Protection calibre  
25 A *  
H 05 VV - F  
H 05 RR - F  
H 05 VV - F  
H 05 RR - F  
230V~ 50/60Hz  
400V~ 50/60Hz  
2 Phases + N  
4 x 1.5 mm²  
16 A *  
* calculated with the simultaneous factor following the standard EN 60 335-2-6/1990  
Connection of the hob  
Setting up the configurations:  
For the various kinds of connection, use the brass bridges which are in the box next the terminal  
Monophase 230V~1P+N  
Put the 1st bridge between terminal 1 and 2, the 2nd between 3 and 4.  
Attach the earth to the terminate “earth”, the neutral N to terminal 4 or 3, the Phase L to one of  
the terminals 1 or 2.  
Biphase 400V~2P+N  
Put a bridge between terminal 3 and 4.  
Attach the earth to the terminate “earth”, the neutral N to terminal 4 or 3, the Phase L1 to the  
terminals 1 and the Phase L2 to the terminal 2.  
Caution! Be careful that the cables are correctly engaged and tightened.  
We cannot be held responsible for any incident resulting from incorrect connection or  
which could arise from the use of an appliance which has not been earthed or has been  
equipped with a faulty earth connection.  
29  
Foster spa  
42041 Brescello (RE) - Italy  
tel. +39.0522.687425 - tel. Servizio Assistenza +39.0522.684450  
fax +39.0522.686019 - fax Servizio Ricambi +39.0522.962166  
13847/3  

Hotpoint 6511 User Manual
GE 27958 User Manual
Cypress CY7C1018CV33 User Manual
Brother BCL D20 User Manual
Black Box Computer Hardware LH1350C ST R3 User Manual
Asus SP97 User Manual
Asus P9d I Is The Mini Itx Form Factor Serverboard P9DI User Manual
Asus P5AD2 E User Manual
Aluratek AWSSDE48F User Manual
321 Studios LG Software Innovations Computer Monitor W2043T User Manual