Fisher Price N8849 User Manual

N8849  
Please keep this instruction sheet for future reference,  
as it contains important information.  
Requires four “D” (LR20) alkaline batteries for mobile  
operation and two "AAA" (LR03) alkaline batteries for  
remote operation (batteries not included).  
Adult assembly is required.  
Tool required for assembly: Phillips screwdriver (not included).  
Parts  
Canopy  
Arm  
4 Soft Toys  
Crib Adaptor  
Remote  
Base  
Retainer  
(2 Pieces)  
Note: All of the screws used to assemble this toy are attached to the product.  
Follow these instructions carefully to fully secure the screws. Tighten and  
loosen all screws with a Phillips screwdriver. Do not over-tighten the screws.  
3
Battery Installation  
1.5V x 4  
“D” (LR20)  
We recommend using alkaline  
batteries for longer battery life.  
Mobile Base  
• Loosen the screws in the battery compartment door with a Phillips screwdriver. Remove the  
battery compartment door.  
• Insert four “D” (LR20) alkaline batteries.  
• Replace the battery compartment door and tighten the screws.  
IMPORTANT! Under normal use conditions, the batteries in the mobile base will require replacement  
more often than the batteries in the remote. When sounds or lights become faint or stop, it’s time  
for an adult to change the batteries.  
1.5V x 2  
"AAA" (LR03)  
We recommend using alkaline  
batteries for longer battery life.  
Remote  
• Loosen the screw in the battery compartment door with a Phillips screwdriver. Remove the battery  
compartment door.  
• Insert two "AAA" (LR03) alkaline batteries.  
• Replace the battery compartment door and tighten the screw.  
• If this product begins to operate erratically, you may need to reset the electronics. Slide the power/  
volume switch on the mobile base off and then back on. Remove the batteries from the remote and  
replace them.  
• Protect the environment by not disposing of this product with household waste (2002/96/EC).  
Check your local authority for recycling advice and facilities (Europe only).  
4
Assembly  
Base  
Crib Adaptor  
1
• Fit the crib adaptor to the base and tighten the screws.  
IMPORTANT! Make sure the straps are over the top of the crib adaptor.  
Canopy  
Arm  
2
• First, fit the top retainer piece onto the end of the arm.  
• Next, fit the canopy onto top retainer piece.  
• Then, fit the bottom retainer piece onto the canopy and tighten the screw.  
5
Assembly  
PRESS  
A
SLIDE  
B
Arm  
Socket  
Base  
3
A
• First, press the button on the mobile base, next to the socket  
B
and then slide the socket door open  
.
• Fit the arm into the socket in the base and tighten the screws.  
Soft Toy  
4
• Fit the string on a soft toy through the slot in the canopy. Pull down gently on the soft toy to  
secure the string in the large leaf spoke.  
• Repeat this procedure to attach the remaining soft toys to the canopy.  
Fisher Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.  
©2008 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.  
N8849pr-0920  
PRINTED IN CHINA  
6
Crib Attachment  
Crib Top Rail  
Base  
Buckles  
1
• Position the base so that the decorated side faces the inside of the crib.  
• Fit the base onto the crib top rail.  
• Make sure the top strap is hanging over the crib top rail. Pull the bottom strap through the crib rails.  
• Buckle the straps. Make sure you hear a “click”.  
2
• Make sure the straps are tightened securely around the crib rail.  
• While pushing the tab at the bottom of the buckle, pull the free end of the strap to tighten on  
the rail.  
Hint: You can secure the free end of the strap to the base.  
To loosen the strap for removal, simply pull the buckle down.  
7
Crib Attachment  
3
• Tie the base strings to a crib spindle.  
Note: It is better the tie the strings in a knot than a bow, since a bow may be easily untied.  
Bottom off Base  
At Least 7 IInches  
Mattress  
4
• If the distance between the base and the mattress is less than 7 inches, lower the crib mattress.  
8
Use  
IMPORTANT!  
• In the unlikely event that use of the remote interferes with normal use of other remote controlled  
equipment, such as televisions, stereos, or use of other electronic or battery powered appliances  
interfere with operation of the mobile, do not use both appliances at the same time.  
• For best performance between the mobile and the remote, avoid using the remote in areas of  
bright light. In bright natural or artificial light, you may notice loss of range. Move the mobile or  
otherwise reduce the amount of light to improve performance.  
Remote  
• When using the remote, make sure that the arrow on the mobile base is pointing towards the  
transmitter window on the remote. For best results make sure the path between the transmitter  
window on the remote and the mobile base are in a direct line and free of obstacles. Position  
the mobile base so that the arrow points to the area from which you’re most likely to use the  
remote. For example, if you’ll most often be using the remote from the doorway of the nursery,  
make sure the arrow on the mobile base is pointing towards the doorway and the path between  
the mobile base and doorway is free from obstructions.  
9
Use  
Projector/Sound Switch  
Slide the switch to:  
- turns on sounds,  
mobile and projector  
- turns on sounds  
and mobile  
- turns on sounds only  
Power/Voluume Switch  
• Slide the switch to on with  
low volume  
volume  
or on with high  
. When finished using  
the product, slide the switch  
off  
.
Music or Sound Seleect Butttons  
Press a music or sound button  
on the front of the mobile base:  
- for Bach, Beethoven  
and Mozart  
- for nature sounds  
- for heartbeat sounds  
10  
Convert to Music Box  
Remove the mobile and use as a music box with a projection show!  
• Loosen both screws in the arm near the mobile  
base. Lift and remove the arm.  
• Close the socket door on top of the mobile base.  
IMPORTANT! The socket door must be closed  
for sound and projection operation. If sounds  
or lights are not working, make sure the door is  
completely closed.  
• Store the mobile in a safe place for future use.  
11  
Consumer Information  
FCC Statement (United States Only)  
This equipment has been tested and found to  
comply with the limits for a Class B digital device,  
pursuant to Part 15 of the FCC Rules. These limits  
are designed to provide reasonable protection  
against harmful interference in a residential  
installation. This equipment generates, uses and  
can radiate radio frequency energy and, if not  
installed and used in accordance with the  
instructions, may cause harmful interference  
to radio communications. However, there is  
no guarantee that interference will not occur  
in a particular installation. If this equipment  
does cause harmful interference to radio or  
television reception, which can be determined  
by turning the equipment off and on, the user is  
encouraged to try to correct the interference by  
one or more of the following measures:  
• Reorient or relocate the receiving antenna.  
• Increase the separation between the equipment  
and receiver.  
• Consult the dealer or an experienced radio/TV  
technician for help.  
Note: Changes or modifications not expressly  
approved by the manufacturer responsible for  
compliance could void the user’s authority to  
operate the equipment.  
This device complies with Part 15 of the  
FCC Rules.  
Operation is subject to the following two  
conditions: (1) this device may not cause  
harmful interference and (2) this device must  
accept any interference received, including  
interference that may cause undesired operation.  
ICES-003  
This Class B digital apparatus complies with  
Canadian ICES-003.  
Operation is subject to the following two  
conditions: (1) this device may not cause harmful  
interference and (2) this device must accept any  
interference received, including interference that  
may cause undesired operation.  
NMB-003  
Cet appareil numérique de la classe B est  
conforme à la norme NMB-003 du Canada.  
Lutilisation de ce dispositif est autorisée  
seulement aux conditions suivantes: (1) il ne doit  
pas produire de brouillage et (2) l’utilisateur du  
dispositif doit être prêt à accepter tout brouillage  
radioélectrique reçu, même si ce brouillage est  
susceptible de compromettre le fonctionnement  
du dispositif.  
12  

HANNspree LIQUID CRYSTAL DISPLAY HF237 User Manual
Dell Computer Monitor ST2010B User Manual
Dell Computer Monitor AW2210T User Manual
Casio DQ 584B User Manual
Brother BCL D20 User Manual
Black Box Computer Hardware ACX160 User Manual
Avaya 16 300310 User Manual
Atmel AT88SC6416CRF User Manual
Asus P5KPL AM SE User Manual
Antec Sonata II 500 User Manual