MVME7100 Single Board Computer
Installation and Use
6806800E08A
November 2008
Contents
About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Safety Notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Sicherheitshinweise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
1.2 Standard Compliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
1.3 Mechanical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
1.4 Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
1.4.1 Supported Board Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
1.4.2 Board Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
2
Hardware Preparation and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
2.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
2.2 Unpacking and Inspecting the Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
2.3 Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
2.3.1 Environmental Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
2.3.2 Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
2.3.3 Thermal Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
2.3.4 Thermally Significant Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
2.3.5 Equipment Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
2.4 Configuring the Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
2.4.1 SMT Configuration Switch, S1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
2.4.1.1 Safe Start Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
2.4.1.2 Boot Block B Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
2.4.1.3 Flash Bank Write Protect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
2.4.1.4 JTAG Pass-Thru . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
2.4.1.5 Low Memory Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
2.4.1.6 PMC 133 MHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
2.4.1.7 Master WP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
2.4.2 Geographical Address Switch, S2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
2.4.3 VME System Controller Select, S2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
2.5 Installing Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
2.5.1 Transition Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
2.5.2 PMC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
2.5.3 XMCspan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
3
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Contents
2.6 Installing and Removing the Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
2.7 Completing the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
2.8 Factory Installed Linux . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
3
Controls, LEDs, and Connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
3.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
3.2 Board Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
3.3 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
3.3.1 Reset/Abort Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
3.3.2 LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
3.3.3 Connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
3.3.3.1 XMC Expansion Connector (J6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
3.3.3.2 Ethernet Connectors (J4A/J4B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
3.3.3.3 PCI Mezzanine Card (PMC) Connectors (J11 – J14, J21 – J23) . . . . . . . . . . 53
3.3.3.4 Serial Port Connector (COM1/J1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
3.3.3.5 VMEbus P1 Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
3.3.3.6 VMEbus P2 Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
3.3.3.7 MVME7216E PMC I/O Module (PIM) Connectors (J10, J14) . . . . . . . . . . . . 63
3.3.3.8 USB Connector (J2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
3.4 Headers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
3.4.1 Processor COP Header (P4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
3.4.2 Boundary Scan Header (P5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
4
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
4.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
4.2 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
4.3 Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
4.4 I2C Serial Interface and Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
4.5 System Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
4.6 Timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
4.7 Ethernet Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
4.8 Local Bus Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
4.8.1 Flash Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
4.8.2 NVRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
4.8.3 Quad UART (QUART) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
4.8.4 Control and Timers PLD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
4.9 DUART Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
4.10 PCI-E Port 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
4.10.1 VME Controller. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
4.10.2 USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
4.11 XMC Expansion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
4.12 Power Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
4.12.1 Power Sequencing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
4.12.2 Power Supply Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
4.12.3 Power Supply Filtering and Fusing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
4
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Contents
4.13 Clock Distribution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
4.13.1 System Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
4.13.2 Real Time Clock Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
4.13.3 Local Bus Controller Clock Divisor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
4.14 Reset Control Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
4.15 Real Time Clock Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
5
Transition Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
5.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
5.2 Transition Module Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
5.3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
5.4 SEEPROM Address Switch, S1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
5.5 Rear Panel Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
5.6 PMC Input/Output Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
6
MOTLoad Firmware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
6.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
6.2 Implementation and Memory Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
6.3 MOTLoad Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
6.3.1 Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
6.3.2 Tests. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
6.3.3 Command List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
6.4 Using the Command Line Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
6.4.1 Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
6.4.2 Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
6.5 Firmware Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
6.5.1 Default VME Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
6.5.2 Control Register/Control Status Register Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
6.5.3 Displaying VME Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
6.5.4 Editing VME Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
6.5.5 Deleting VME Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
6.5.6 Restoring Default VME Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
6.6 Remote Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
6.7 Boot Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
6.7.1 Checksum Algorithm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
6.7.2 Image Flags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
6.7.3 User Images. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
6.7.4 Alternate Boot Data Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
6.7.5 Alternate Boot Images and Safe Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
6.7.6 Boot Image Firmware Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
6.8 Startup Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
A
Battery Exchange . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
A.1 Battery Exchange . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
5
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Contents
B
Related Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
B.1 Emerson Network Power - Embedded Computing Documents . . . . . . . . . . . . . . . . . . . . . . . 101
B.2 Manufacturers’ Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
B.3 Related Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
6
MVME7100 Single Board Computer Installation and Use (6806800E08A)
List of Tables
Table 1-1
Table 1-2
Table 1-3
Table 1-4
Table 2-1
Table 2-2
Table 2-3
Table 2-4
Table 2-5
Table 2-6
Table 3-1
Table 3-2
Table 3-3
Table 3-4
Table 3-5
Table 3-6
Table 3-7
Table 3-8
Table 3-9
Features List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Board Standard Compliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Mechanical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Board Variants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Startup Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
MVME7100 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Thermally Significant Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Configuration Switch Settings (S1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
VME System Controller and GA Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Front Panel LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Baseboard Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
XMC Expansion Connector (J6) Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Ethernet Connectors (J4A/J4B) Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
PMC Slot 1 Connector (J11) Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
PMC Slot 1 Connector (J12) Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
PMC Slot 1 Connector (J13) Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
PMC Slot 1 Connector (J14) Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
PMC Slot 2 Connector (J21) Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Table 3-10 PMC Slot 2 Connector (J22) Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Table 3-11 PMC Slot 2 Connector (J23) Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Table 3-12 COM1 Port Connector Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Table 3-13 VMEbus P1 Connector Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Table 3-14 VME P2 Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Table 3-15 MVME721 Host I/O Connector (J10) Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . 63
Table 3-16 USB Connector (J2) Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Table 3-17 Processor COP Header (P4) Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Table 3-18 Boundary Scan Header (P5) Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Table 4-1
Table 5-1
Table 5-2
Table 5-3
Table 5-4
Table 5-5
Table 6-1
Table 6-2
Table B-1
Table B-2
Table B-3
Clock Frequencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Transition Module Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
SEEPROM Address Switch Assignments (RTM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Switch Settings and Device Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Transition Module Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Transition Module LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
MOTLoad Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
MOTLoad Image Flags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Emerson Network Power - Embedded Computing Publications . . . . . . . . . . . . . . . . 101
Manufacturer’s Publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Related Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
7
MVME7100 Single Board Computer Installation and Use (6806800E08A)
List of Tables
8
MVME7100 Single Board Computer Installation and Use (6806800E08A)
List of Figures
Figure 2-1
Figure 2-2
Figure 2-3
Figure 2-4
Figure 2-5
Figure 2-6
Figure 3-1
Figure 3-2
Figure 4-1
Figure 5-1
Figure 5-2
Figure 5-3
Figure 5-4
Figure 5-5
Primary Side Thermally Significant Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Secondary Side Thermally Significant Components . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Switch Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
SMT Configuration Switch Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Geographical Address Switch Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Typical Placement of a PMC Module on a VME Module . . . . . . . . . . . . . . . . . . . . . . . 43
Component Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Front Panel LEDs, Connectors, Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Component Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
S1 Switch Positions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Rear Panel Connectors and LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Installing the PIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Figure A-1 Battery Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
9
MVME7100 Single Board Computer Installation and Use (6806800E08A)
List of Figures
10
MVME7100 Single Board Computer Installation and Use (6806800E08A)
About this Manual
Overview of Contents
This manual provides the information required to install and configure an MVME7100 Single
Board Computer. Additionally, this manual provides specific preparation and installation
information and data applicable to the board.
The MVME7100 is a high-performance, dual core processor board featuring the Freescale
8641D with a dedicated bridge to each processor.
This manual is divided into the following chapters and appendices:
Safety Notes, contains the cautions and warnings applicable to the use of this product.
Sicherheitshinweise, contains the cautions and warnings applicable to the use of this product
translated to the German language.
Chapter 1, Introduction, lists the features of the MVME7100 baseboard, standard compliances,
and model numbers for boards and accessories.
Chapter 2, Hardware Preparation and Installation, includes a description of the MVME7100,
unpacking instructions, environmental, thermal, and power requirements, and how to prepare
and install the baseboard, transition module, and PMC module.
Chapter 3, Controls, LEDs, and Connectors, provides an illustration of the board components
and front panel details. This chapter also gives descriptions for the onboard and front panel
LEDs and connectors.
Chapter 4, Functional Description, describes the major features of the MVME7100 baseboard.
These descriptions include both programming and hardware characteristics of major
components.
Chapter 5, Transition Module, describes the MVME7216E transition module used with the
MVME7100.
Chapter 6, MOTLoad Firmware, describes the role, process and commands employed by the
MVME7100 diagnostic and initialization firmware MOTLoad. This chapter also briefly describes
how to use the debugger commands.
Appendix A, Battery Exchange, describes the procedure for replacing a battery.
Appendix B, Related Documentation, provides listings for publications, manufacturer’s
documents and related industry specification for this product.
11
MVME7100 Single Board Computer Installation and Use (6806800E08A)
About this Manual
Abbreviations
This document uses the following abbreviations:
TERM
A
MEANING
Amps
A/D
Analog/Digital
ANSI
ASIC
BGA
BLT
American National Standard Institute
Application Specific Integrated Circuit
Ball Grid Array
Block Transfer
CCB
CE
Core Complex Bus
Chip Enable
CFM
CHRP
CMC
COM
COP
COTS
CPU
CRC
DDR
oC
Cubic Feet per Minute
(PowerPC) Common Hardware Reference Platform
Common Mezzanine Card
Communications
Common On-chip Processor
Commercial-Off-the-Shelf
Central Processing Unit
Cyclic Redundancy Check
Double Data Rate
Degrees Celsius
DLL
Delay-Locked Loop
DMA
DRAM
DUART
ECC
EEPROM
EPROM
FCC
FEC
Direct Memory Access
Dynamic Random Access Memory
Dual Universal Asynchronous Receiver/Transmitter
Error Correction Code
Electrically Erasable Programmable Read-Only Memory
Erasable Programmable Read-Only Memory
Federal Communications Commission
Fast Ethernet Controller
First In First Out
FIFO
F/W
Firmware
fpBGA
GB
Flip chip Plastic Ball Grid Array
Gigabytes
Gbit
Gigabit
Gbps
GMII
Gigabits Per Second
Gigabit Media Independent Interface
12
MVME7100 Single Board Computer Installation and Use (6806800E08A)
About this Manual
TERM
GPCM
GPR
H/W
ID
MEANING
General Purpose Chip select Machine
General Purpose Register
Hardware
Identification
IDMA
I/O
Independent Direct Memory Access
Input/Output
IEEE
I2C
Institute of Electrical and Electronics Engineers
Inter IC
JTAG
KB
Joint Test Access Group
Kilobytes
KBAUD
LBC
LCD
LED
LSB
Kilo Baud
Local Bus Controller
Liquid Crystal Display
Light Emitting Diode
Least Significant Byte
Megabytes
MB
Mbit
Megabit
MBLT
Mbps
MHz
MII
Multiplexed Block Transfer
Megabits Per Second
Megahertz
Media Independent Interface
Most Significant Byte
MSB
Msb
Most Significant Bit
MTBF
NAND
NOR
OS
Mean Time Between Failure
(Not and) Flash that is used for storage
(Not or) Flash that is used for executing code
Operating System
PBGA
PCI
Plastic Ball Grid Array
Peripheral Component Interconnect
Peripheral Component Interconnect -X
Programmable Interrupt Controller
PCI Mezzanine Card Input/Output Module
PCI Mezzanine Card (IEEE P1386.1)
Programmable Logic Device
Phase-Locked Loop
PCI-X
PIC
PIM
PMC
PLD
PLL
POR
Ppm
Power-On Reset
Parts Per Million
13
MVME7100 Single Board Computer Installation and Use (6806800E08A)
About this Manual
TERM
MEANING
PRD
PReP
PrPMC
QUART
RAM
Rcv
Product Requirements Document
PowerPC Reference Platform
Processor PCI Mezzanine Card
Quad Universal Asynchronous Receiver/Transmitter
Random Access Memory
Receive
RGMII
ROM
RTBI
RTC
Reduced Gigabit Media Independent Interface
Read-Only Memory
Reduced Ten Bit Interface
Real-Time Clock
RTM
sATA
SBC
Rear Transition Module
Serial AT Attachment
Single Board Computer
SDRAM
SMT
SODIMM
SPD
Synchronous Dynamic Random Access Memory
Surface Mount Technology
Small-Outline Dual In-line Memory Module
Serial Presence Detect
SRAM
S/W
Static Random Access Memory
Software
TBI
Ten Bit Interface
TSEC
2eSST
UART
USB
Three-Speed Ethernet Controller
Two edge Source Synchronous Transfer
Universal Asynchronous Receiver/Transmitter
Universal Serial Bus
V
Volts
VIO
Input/Output Voltage
VITA
VME
VPD
VMEbus International Trade Association
VMEbus (Versa Module Eurocard)
Vital Product Data
W
Watts
Xmit
Transmit
14
MVME7100 Single Board Computer Installation and Use (6806800E08A)
About this Manual
Conventions
The following table describes the conventions used throughout this manual.
Notation
Description
0x00000000
Typical notation for hexadecimal numbers
(digits are 0 through F), for example used for
addresses and offsets
0b0000
bold
Same for binary numbers (digits are 0 and 1)
Used to emphasize a word
Screen
Used for on-screen output and code related
elements or commands in body text
Courier + Bold
Used to characterize user input and to
separate it from system output
Reference
Used for references and for table and figure
descriptions
File > Exit
<text>
Notation for selecting a submenu
Notation for variables and keys
[text]
Notation for software buttons to click on the
screen and parameter description
...
Repeated item for example node 1, node 2,
..., node 12
.
.
.
Omission of information from
example/command that is not necessary at
the time being
..
Ranges, for example: 0..4 means one of the
integers 0,1,2,3, and 4 (used in registers)
|
Logical OR
Indicates a hazardous situation which, if not
avoided, could result in death or serious
injury
Indicates a hazardous situation which, if not
avoided, may result in minor or moderate
injury
Indicates a property damage message
No danger encountered. Pay attention to
important information
15
MVME7100 Single Board Computer Installation and Use (6806800E08A)
About this Manual
Summary of Changes
This is the first edition of the MVME7100 Single Board Computer Installation and Use.
Part Number
Publication Date
Description
6806800E08A
November 2008
First edition
Comments and Suggestions
We welcome and appreciate your comments on our documentation. We want to know what you
think about our manuals and how we can make them better.
Mail comments to us by filling out the following online form:
http://www.emersonnetworkpowerembeddedcomputing.com/ > Contact Us > Online Form
In “Area of Interest” select “Technical Documentation". Be sure to include the title, part number,
and revision of the manual and tell us how you used it.
16
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Safety Notes
This section provides warnings that precede potentially dangerous procedures
throughout this manual. Instructions contained in the warnings must be followed during
all phases of operation, service, and repair of this equipment. You should also employ
all other safety precautions necessary for the operation of the equipment in your
operating environment. Failure to comply with these precautions or with specific
warnings elsewhere in this manual could result in personal injury or damage to the
equipment.
Emerson intends to provide all necessary information to install and handle the product
in this manual. Because of the complexity of this product and its various uses, we do not
guarantee that the given information is complete. If you need additional information, ask
your Emerson representative.
The product has been designed to meet the standard industrial safety requirements. It
must not be used except in its specific area of office telecommunication industry and
industrial control.
Only personnel trained by Emerson or persons qualified in electronics or electrical
engineering are authorized to install, remove or maintain the product.
The information given in this manual is meant to complete the knowledge of a specialist
and must not be used as replacement for qualified personnel.
Keep away from live circuits inside the equipment. Operating personnel must not
remove equipment covers. Only Factory Authorized Service Personnel or other qualified
service personnel may remove equipment covers for internal subassembly or
component replacement or any internal adjustment.
Do not install substitute parts or perform any unauthorized modification of the
equipment or the warranty may be voided. Contact your local Emerson representative for
service and repair to make sure that all safety features are maintained.
EMC
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own expense.
Changes or modifications not expressly approved by Emerson Network Power could
void the user's authority to operate the equipment. Board products are tested in a
17
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Safety Notes
representative system to show compliance with the above mentioned requirements. A
proper installation in a compliant system will maintain the required performance. Use
only shielded cables when connecting peripherals to assure that appropriate radio
frequency emissions compliance is maintained.
18
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Safety Notes
Operation
Product Damage
High humidity and condensation on the board surface causes short circuits.
Do not operate the board outside the specified environmental limits.
Make sure the board is completely dry and there is no moisture on any surface before
applying power.
Damage of Circuits
Electrostatic discharge and incorrect installation and removal can damage circuits or
shorten their life.
Before touching the board or electronic components, make sure that you are working in
an ESD-safe environment.
Board Malfunction
Switches marked as “reserved” might carry production-related functions and can cause
the board to malfunction if their setting is changed.
Do not change settings of switches marked as “reserved”. The setting of switches which
are not marked as “reserved” has to be checked and changed before board installation.
Installation
Data Loss
Powering down or removing a board before the operating system or other software
running on the board has been properly shut down may cause corruption of data or file
systems.
Make sure all software is completely shut down before removing power from the board
or removing the board from the chassis.
Product Damage
Only use injector handles for board insertion to avoid damage to the front panel and/or
PCB. Deformation of the front panel can cause an electrical short or other board
malfunction.
Product Damage
Inserting or removing modules with power applied may result in damage to module
components.
Before installing or removing additional devices or modules, read the documentation
that came with the product.
19
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Safety Notes
Cabling and Connectors
Product Damage
RJ-45 connectors on modules are either twisted-pair Ethernet (TPE) or E1/T1/J1 network
interfaces. Connecting an E1/T1/J1 line to an Ethernet connector may damage your
system.
z
z
z
Make sure that TPE connectors near your working area are clearly marked as
network connectors.
Verify that the length of an electric cable connected to a TPE bushing does not
exceed 100 meters.
Make sure the TPE bushing of the system is connected only to safety extra low
voltage circuits (SELV circuits).
If in doubt, ask your system administrator.
Battery
Board/System Damage
Incorrect exchange of lithium batteries can result in a hazardous explosion.
When exchanging the on-board lithium battery, make sure that the new and the old
battery are exactly the same battery models.
If the respective battery model is not available, contact your local Emerson sales
representative for the availability of alternative, officially approved battery models.
Data Loss
Exchanging the battery can result in loss of time settings. Backup power prevents the
loss of data during exchange.
Quickly replacing the battery may save time settings.
Data Loss
If the battery has low or insufficient power the RTC is initialized.
Exchange the battery before seven years of actual battery use have elapsed.
PCB and Battery Holder Damage
Removing the battery with a screw driver may damage the PCB or the battery holder. To
prevent damage, do not use a screw driver to remove the battery from its holder.
20
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Sicherheitshinweise
Dieses Kapitel enthält Hinweise, die potentiell gefährlichen Prozeduren innerhalb dieses
Handbuchs vorrangestellt sind. Beachten Sie unbedingt in allen Phasen des Betriebs,
der Wartung und der Reparatur des Systems die Anweisungen, die diesen Hinweisen
enthalten sind. Sie sollten außerdem alle anderen Vorsichtsmaßnahmen treffen, die für
den Betrieb des Produktes innerhalb Ihrer Betriebsumgebung notwendig sind. Wenn Sie
diese Vorsichtsmaßnahmen oder Sicherheitshinweise, die an anderer Stelle diese
Handbuchs enthalten sind, nicht beachten, kann das Verletzungen oder Schäden am
Produkt zur Folge haben.
Emerson ist darauf bedacht, alle notwendigen Informationen zum Einbau und zum
Umgang mit dem Produkt in diesem Handbuch bereit zu stellen. Da es sich jedoch um
ein komplexes Produkt mit vielfältigen Einsatzmöglichkeiten handelt, können wir die
Vollständigkeit der im Handbuch enthaltenen Informationen nicht garantieren. Falls Sie
weitere Informationen benötigen sollten, wenden Sie sich bitte an die für Sie zuständige
Geschäftsstelle von Emerson.
Das System erfüllt die für die Industrie geforderten Sicherheitsvorschriften und darf
ausschließlich für Anwendungen in der Telekommunikationsindustrie und im
Zusammenhang mit Industriesteuerungen verwendet werden.
Einbau, Wartung und Betrieb dürfen nur von durch Emerson ausgebildetem oder im
Bereich Elektronik oder Elektrotechnik qualifiziertem Personal durchgeführt werden. Die
in diesem Handbuch enthaltenen Informationen dienen ausschließlich dazu, das Wissen
von Fachpersonal zu ergänzen, können dieses jedoch nicht ersetzen.
Halten Sie sich von stromführenden Leitungen innerhalb des Produktes fern. Entfernen
Sie auf keinen Fall Abdeckungen am Produkt. Nur werksseitig zugelassenes
Wartungspersonal oder anderweitig qualifiziertes Wartungspersonal darf Abdeckungen
entfernen, um Komponenten zu ersetzen oder andere Anpassungen vorzunehmen.
Installieren Sie keine Ersatzteile oder führen Sie keine unerlaubten Veränderungen am
Produkt durch, sonst verfällt die Garantie. Wenden Sie sich für Wartung oder Reparatur
bitte an die für Sie zuständige Geschäftsstelle von Emerson. So stellen Sie sicher, dass
alle sicherheitsrelevanten Aspekte beachtet werden.
EMV
Das Produkt wurde in einem Emerson Standardsystem getestet. Es erfüllt die für digitale
Geräte der Klasse A gültigen Grenzwerte in einem solchen System gemäß den FCC-
Richtlinien Abschnitt 15 bzw. EN 55022 Klasse A. Diese Grenzwerte sollen einen
angemessenen Schutz vor Störstrahlung beim Betrieb des Produktes in Gewerbe- sowie
Industriegebieten gewährleisten.
21
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Sicherheitshinweise
Das Produkt arbeitet im Hochfrequenzbereich und erzeugt Störstrahlung. Bei
unsachgemäßem Einbau und anderem als in diesem Handbuch beschriebenen Betrieb
können Störungen im Hochfrequenzbereich auftreten.
Wird das Produkt in einem Wohngebiet betrieben, so kann dies mit grosser
Wahrscheinlichkeit zu starken Störungen führen, welche dann auf Kosten des
Produktanwenders beseitigt werden müssen. Änderungen oder Modifikationen am
Produkt, welche ohne ausdrückliche Genehmigung von Emerson Network Power
durchgeführt werden, können dazu führen, dass der Anwender die Genehmigung zum
Betrieb des Produktes verliert. Boardprodukte werden in einem repräsentativen System
getestet, um zu zeigen, dass das Board den oben aufgeführten EMV-Richtlinien
entspricht. Eine ordnungsgemässe Installation in einem System, welches die EMV-
Richtlinien erfüllt, stellt sicher, dass das Produkt gemäss den EMV-Richtlinien betrieben
wird. Verwenden Sie nur abgeschirmte Kabel zum Anschluss von Zusatzmodulen. So ist
sichergestellt, dass sich die Aussendung von Hochfrequenzstrahlung im Rahmen der
erlaubten Grenzwerte bewegt.
Warnung! Dies ist eine Einrichtung der Klasse A. Diese Einrichtung kann im
Wohnbereich Funkstörungen verursachen. In diesem Fall kann vom Betreiber verlangt
werden, angemessene Maßnahmen durchzuführen.
Betrieb
1 Beschädigung des Produktes
Hohe Luftfeuchtigkeit und Kondensat auf der Oberfläche des Produktes können zu
Kurzschlüssen führen.
Betreiben Sie das Produkt nur innerhalb der angegebenen Grenzwerte für die relative
Luftfeuchtigkeit und Temperatur. Stellen Sie vor dem Einschalten des Stroms sicher,
dass sich auf dem Produkt kein Kondensat befindet.
Beschädigung von Schaltkreisen
Elektrostatische Entladung und unsachgemäßer Ein- und Ausbau des Produktes kann
Schaltkreise beschädigen oder ihre Lebensdauer verkürzen.
Bevor Sie das Produkt oder elektronische Komponenten berühren, vergewissern Sie
sich, daß Sie in einem ESD-geschützten Bereich arbeiten.
Fehlfunktion des Produktes
Schalter, die mit 'Reserved' gekennzeichnet sind, können mit produktionsrelevanten
Funktionen belegt sein. Das Ändern dieser Schalter kann im normalen Betrieb
Störungen auslösen.
Verstellen Sie nur solche Schalter, die nicht mit 'Reserved' gekennzeichnet sind. Prüfen
und ggf. ändern Sie die Einstellungen der nicht mit 'Reserved' gekennzeichneten
Schalter, bevor Sie das Produkt installieren.
22
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Sicherheitshinweise
Installation
Datenverlust
Das Herunterfahren oder die Deinstallation eines Boards bevor das Betriebssystem oder
andere auf dem Board laufende Software ordnungsmemäss beendet wurde, kann zu
partiellem Datenverlust sowie zu Schäden am Filesystem führen.
Stellen Sie sicher, dass sämtliche Software auf dem Board ordnungsgemäss beendet
wurde, bevor Sie das Board herunterfahren oder das Board aus dem Chassis entfernen.
Beschädigung des Produktes
Fehlerhafte Installation des Produktes kann zu einer Beschädigung des Produktes
führen.
Verwenden Sie die Handles, um das Produkt zu installieren/deinstallieren. Auf diese
Weise vermeiden Sie, dass das Face Plate oder die Platine deformiert oder zerstört wird.
Beschädigung des Produktes und von Zusatzmodulen
Fehlerhafte Installation von Zusatzmodulen, kann zur Beschädigung des Produktes und
der Zusatzmodule führen.
Lesen Sie daher vor der Installation von Zusatzmodulen die zugehörige Dokumentation.
Kabel und Stecker
Beschädigung des Produktes
Bei den RJ-45-Steckern, die sich an dem Produkt befinden, handelt es sich entweder um
Twisted-Pair-Ethernet (TPE) oder um E1/T1/J1-Stecker. Beachten Sie, dass ein
versehentliches Anschließen einer E1/T1/J1-Leitung an einen TPE-Stecker das Produkt
zerstören kann.
z
z
z
Kennzeichnen Sie deshalb TPE-Anschlüsse in der Nähe Ihres Arbeitsplatzes
deutlich als Netzwerkanschlüsse.
Stellen Sie sicher, dass die Länge eines mit Ihrem Produkt verbundenen TPE-Kabels
100 m nicht überschreitet.
Das Produkt darf über die TPE-Stecker nur mit einem Sicherheits-Kleinspannungs-
Stromkreis (SELV) verbunden werden.
Bei Fragen wenden Sie sich an Ihren Systemverwalter.
23
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Sicherheitshinweise
Batterie
Beschädigung des Blades
Ein unsachgemäßer Einbau der Batterie kann gefährliche Explosionen und
Beschädigungen des Blades zur Folge haben.
Verwenden Sie deshalb nur den Batterietyp, der auch bereits eingesetzt wurde und
befolgen Sie die Installationsanleitung.
Datenverlust
Wenn Sie die Batterie austauschen, können die Zeiteinstellungen verloren gehen. Eine
Backupversorgung verhindert den Datenverlust während des Austauschs.
Wenn Sie die Batterie schnell austauschen, bleiben die Zeiteinstellungen
möglicherweise erhalten.
Datenverlust
Wenn die Batterie wenig oder unzureichend mit Spannung versorgt wird, wird der RTC
initialisiert.
Tauschen Sie die Batterie aus, bevor sieben Jahre tatsächlicher Nutzung vergangen
sind.
Schäden an der Platine oder dem Batteriehalter
Wenn Sie die Batterie mit einem Schraubendreher entfernen, können die Platine oder der
Batteriehalter beschädigt werden.
Um Schäden zu vermeiden, sollten Sie keinen Schraubendreher zum Ausbau der
Batterie verwenden.
Umweltschutz
Entsorgen Sie alte Batterien und/oder Blades/Systemkomponenten/RTMs stets gemäß
der in Ihrem Land gültigen Gesetzgebung, wenn möglich immer umweltfreundlich.
24
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Introduction
1
1.1 Features
The MVME7100 Single Board Computer is a VMEbus board based on the MC8640D and
MC8641D integrated PowerPC processors. It is a full 6U board and occupies a single VME card
slot with PMC cards installed. The MVME7100 is compliant with the VITA standards VMEbus,
2eSST, and PCI-X as listed in Appendix B, Related Documentation.
Table 1-1 Features List
Function
Features
Processor / Host Controller / One MC864xD Integrated Processor
Memory Controller
Two e600 cores with integrated L2
Core frequency of 1.067 or 1.33 GHz
One integrated four channel DMA controller
Two integrated PCIE interfaces
Four integrated 10/100/1000 Ethernet controllers
One integrated DUART
2
Two integrated I C controllers
One integrated Programmable Interrupt Controller
One integrated Local Bus Controller
Two integrated DDR2 SDRAM controllers
System Memory
Two banks of DDR2 SDRAM with ECC
1GB, 2 GB, or 4 GB
2
I C
One 8 KB VPD serial EEPROM
Two 64 KB user configuration serial EEPROMs
One Real Time Clock (RTC) with removable battery
Dual temperature sensor
Two SPDs for memory
Connection to XMCspan and rear transition module
NOR Flash
128 MB soldered flash with two alternate 1 MB boot sectors selectable
via hardware switch
H/W switch or S/W bit write protection for entire logical bank
Up to two devices available:
NAND Flash
z
z
z
4 GB - 1 device
8 GB - 1 device
16 GB - 2 devices
NVRAM
One 512 KB MRAM extended temperature range (-40°C to
105°C/-40°F to 221°F)
Two 64 KB serial EEPROMs
25
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Introduction
Features
Table 1-1 Features List (continued)
Function
Features
PCI_E
8X Port to XMC Expansion
8X Port to 5 Port PCI Express switch
I/O
One front panel mini DB-9 connector for front I/O: one serial channel
Two front panel RJ-45 connectors with integrated LEDs for front I/O:
two 10/100/1000 Ethernet channels
One front panel USB Type A upright receptacle for front I/O: one USB
2.0 channel
PMC site 1 front I/O and rear P2 I/O
PMC site 2 front I/O
USB
One four-channel USB 2.0 controller: one channel for front panel I/O
Ethernet
Four 10/100/1000 MC864xD Ethernet channels: two front panel
Ethernet connectors and two channels for rear P2 I/O
Serial Interface
One 16550-compatible, 9.6 to 115.2 Kbaud, MC864xD, asynchronous
serial channel: one channel for front panel I/O
One quad UART (QUART) controller to provide four 16550-compatible,
9.6 to 115.2 Kbaud, asynchronous serial channels: four channels for
rear P2 I/O
Timers
Four 32-bit MC864xD timers
Four 32-bit timers in a PLD
Watchdog Timer
VME Interface
One watchdog timer in PLD
VME64 (ANSI/VITA 1-1994) compliant (3 row backplane 96-pin VME
connector)
VME64 Extensions (ANSI/VITA 1.1-1997) compliant (5 row backplane
160-pin VME connector)
2eSST (ANSI/VITA 1.5-2003) compliant
Two five-row P1 and P2 backplane connectors
One Tsi148 VMEbus controller
Form Factor
Standard 6U VME, one slot
Miscellaneous
One front panel RESET/ABORT switch
Six front panel status indicators:
z
z
z
Two 10/100/1000 Ethernet link/speed and activity (4 total)
Board fail
User S/W controlled LED
Planar status indicators
One standard 16-pin JTAG/COP header
Boundary scan support
Switches for VME geographical addressing in a three-row backplane
Software Support
VxWorks OS support
Linux OS support
26
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Standard Compliances
Introduction
1.2 Standard Compliances
The MVME7100 is designed to be CE compliant and to meet the following standard
requirements.
Table 1-2 Board Standard Compliances
Standard
Description
UL 60950-1
Safety Requirements (legal)
EN 60950-1
IEC 60950-1
CAN/CSA C22.2 No 60950-1
CISPR 22
EMC requirements (legal) on system level (predefined Emerson
system)
CISPR 24
EN 55022
EN 55024
FCC Part 15
Industry Canada ICES-003
VCCI Japan
AS/NZS CISPR 22
EN 300 386
NEBS Standard GR-1089 CORE
NEBS Standard GR-63-CORE
ETSI EN 300 019 series
Environmental Requirements
Directive 2002/95/EC
Directive on the restriction of the use of certain hazardous
substances in electrical and electronic equipment (RoHS)
1.3 Mechanical Data
This section provides details on the board’s mechanical data.
Table 1-3 Mechanical Data
Characteristic
Dimensions (D x W x H)
Weight
Value
6U, 4HP wide, (233 mm x 160 mm x 20 mm)
0.680 kg
27
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Introduction
Ordering Information
1.4 Ordering Information
When ordering board variants or board accessories, use the order numbers given in the
following tables.
1.4.1
Supported Board Models
At the time of publication of this manual, the MVME7100 Single Board Computer is available in
the configurations shown below.
Table 1-4 Board Variants
Marketing #
Processor
MVME7100-0161
MVME7100-0163
MVME7100-0171
MVME7100-0173
MC8640D 1.067 GHz, 1 GB DDR, 4 GB NAND Flash, Scanbe handles
MC8640D 1.067 GHz, 1 GB DDR, 4 GB NAND Flash, IEEE handles
MC8641D 1.33 GHz, 2 GB DDR, 8 GB NAND Flash, Scanbe handles
MC8641D 1.33 GHz, 2 GB DDR, 8 GB NAND Flash, IEEE handles
1.4.2
Board Accessories
This table lists the available expansion and transition modules for the MVME7100.
Model Number
MVME7216E-001
XMCSPAN-001
XMCSPAN-002
Description
Transition module, 6E
XMC Expansion, IEEE handles
XMC Expansion, Scanbe handles
The IPMC712 and IPMC761 I/O modules are not supported on the MVME7100 SBC.
28
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Hardware Preparation and Installation
2
2.1 Overview
This chapter provides startup and safety instructions related to this product, hardware
preparation instruction that includes default switch settings. System considerations and
installation instructions for the baseboard, PMC, and transition module are also described in
this chapter.
A fully implemented MVME7100 consists of the baseboard plus:
z
z
Two single-wide or one double-wide PCI Mezzanine Card (PMC) slot for added versatility.
One transition module for support of the mapped I/O from the MVME7100 baseboard to the
P2 connector.
z
Up to two optional XMCspan cards.
The following table lists the things you will need to do before you can use this board and tells
you where to find the information you need to perform each step. Be sure to read this entire
chapter, including all Caution and Warning notes, before you begin.
Table 2-1 Startup Overview
Task
Page
Unpack the hardware.
Unpacking and Inspecting the Board on page 30
Configure the hardware by setting jumpers
on the board and RTM.
Configuring the Board on page 36 and SEEPROM
Address Switch, S1 on page 76
Install the MVME7216E transition module in Transition Module on page 40
the chassis.
Install PMC module (if required).
Install XMCspan module (if required).
Install the MVME7100 in the chassis.
Attach cabling and apply power.
Installing Accessories on page 40
XMCspan Installation and Use (6806800H03)
Installing and Removing the Board on page 43
Completing the Installation on page 45
Install PIM on transition module (if required). PMC Input/Output Module on page 79
Ensure that the firmware initializes the
MVME7100
Chapter 6, MOTLoad Firmware
Initialize the board
Chapter 6, MOTLoad Firmware
Examine and/or change environmental
parameters.
MVME7100 Single Board Computer Programmer’s
Reference
Program the board as needed for your
applications.
MVME7100 Single Board Computer Programmer’s
Reference
29
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Hardware Preparation and Installation
Unpacking and Inspecting the Board
2.2 Unpacking and Inspecting the Board
Read all notices and cautions prior to unpacking the product.
Damage of Circuits
Electrostatic discharge and incorrect installation and removal can damage circuits or
shorten their life.
Before touching the board or electronic components, make sure that you are working
in an ESD-safe environment.
Shipment Inspection
To inspect the shipment, perform the following steps:
1. Verify that you have received all items of your shipment.
2. Check for damage and report any damage or differences to customer service.
3. Remove the desiccant bag shipped together with the board and dispose of it
according to your country’s legislation.
The product is thoroughly inspected before shipment. If any damage occurred during
transportation or any items are missing, contact customer service immediately.
30
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Requirements
Hardware Preparation and Installation
2.3 Requirements
Make sure that the board, when operated in your particular system configuration, meets the
requirements specified in the next sections.
2.3.1
Environmental Requirements
The following table lists the currently available specifications for the environmental
characteristics of the MVME7100. A complete functional description of the MVME7100
baseboard appears in Chapter 4, Functional Description.
Operating temperatures refer to the temperature of the air circulating around the board
and not to the component temperature.
Table 2-2 MVME7100 Specifications
Characteristics
Operating
Nonoperating
Operating temperature
0°C to +55°C (32°F to 131°F) entry –40°C to +85° C (-40°F to 185°F)
air with forced-air cooling
Temperature change
+/-0.5° C/min according to NEBS
Standard GR-63-CORE
Relative humidity
Vibration
5% to 90% noncondensing
5% to 90% noncondesning
1 G sine sweep, 5-100 Hz,
horizontal and vertical (NEBS1)
Shock
20 G peak (half sine) 11mSec
Free Fall
100 mm (unpackaged) per GR-63-
CORE
Product Damage
High humidity and condensation on the board surface causes short circuits.
Do not operate the board outside the specified environmental limits.
Make sure the board is completely dry and there is no moisture on any surface before
applying power.
31
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Hardware Preparation and Installation
Power Requirements
2.3.2
Power Requirements
The MVME7100 uses only +5.0 V from the VMEbus backplane. On board power supplies
generate the required voltages for the various ICs. The MVME 7100 connects the +12 V and -
12 V supplies from the backplane to the PMC sites while the +3.3 V power supplied to the PMC
sites comes from the +5.0 V backplane power. A maximum of 10 A of +3.3 V power is available
to the PMC sites, however the 90 W +5.0 V limit must be observed as well as any cooling
limitations.
The next table provides an estimate of the typical and maximum power required.
Table 2-3 Power Requirements
Board Variant
Power
MVME7100-0161
Typical: 40 W @ +5 V
Maximum: 55 W @ +5 V
MVME7100-0163
MVME7100-0171
MVME7100-0173
Typical: 40 W @ +5 V
Maximum: 55 W @ +5 V
Typical: 45 W @ +5 V
Maximum: 60 W @ +5 V
Typical: 45 W @ +5 V
Maximum: 60 W @ +5 V
The following table shows the power available when the MVME7100 is installed in either a 3-
row or 5-row chassis and when PMCs are present.
Chassis Type
3-Row
Available Power
70 W maximum
90 W maximum
Power With PMCs
1
Below 70 W
1
5-Row
Below 90 W
1. Keep below power limit. Cooling limitations must be considered.
32
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Thermal Requirements
Hardware Preparation and Installation
2.3.3
2.3.4
Thermal Requirements
The MVME7100 module requires a minimum air flow of 10 CFM uniformly distributed across
the board, with the airflow traveling from the heat sink to the PMC2 site, when operating at a
55°C (131°F) ambient temperature.
Thermally Significant Components
The following table summarizes components that exhibit significant temperature rises. These
are the components that should be monitored in order to assess thermal performance. The
table also supplies the component reference designator and the maximum allowable operating
temperature.
You can find components on the board by their reference designators as shown in Figure 2-1
and Figure 2-2 on the next page. Versions of the board that are not fully populated may not
contain some of these components.
The preferred measurement location for a component may be junction, case, or ambient as
specified in the table. Junction temperature refers to the temperature measured by an on-chip
thermal device. Case temperature refers to the temperature at the top, center surface of the
component. Air temperature refers to the ambient temperature near the component.
Table 2-4 Thermally Significant Components
Maximum Allowable
Reference
Designator
Component Temperature
in Centigrade
Generic Description
Measurement Location
Ambient
U27, U4
Gb Ethernet Transceiver 0° to +70°
U25, U26, U28
PCI-X/PCI-Express
Bridge
-40° to +85°
Ambient
U22
U24
PCI-Express Bridge
VME Bridge
-40° to +85°
0° to + 70°
0° to +95°
Ambient
Ambient
Case
U10, U11, U12,
U13, U14, U56,
U57, U58, U59,
U6, U60, U61,
U62, U63, U64,
U7, U8, U9
DDR2 SDRAM
U20
MPU
0° to +105°
Junction
33
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Hardware Preparation and Installation
Thermally Significant Components
Figure 2-1 Primary Side Thermally Significant Components
U4
U10 U11 U12 U13 U14
U6
U8 U9
U7
U20
U22
U24
U25
U26
U27
U28
Figure 2-2 Secondary Side Thermally Significant Components
U60 U61 U62 U63 U64
U56
U58 U59
U57
34
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Equipment Requirements
Hardware Preparation and Installation
2.3.5
Equipment Requirements
The following equipment is recommended to complete an MVME7100 system:
z
z
z
z
VMEbus system enclosure
System console terminal
Operating system (and/or application software)
Transition module and connecting cables
35
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Hardware Preparation and Installation
Configuring the Board
2.4 Configuring the Board
To produce the desired configuration and ensure proper operation of the MVME7100, you may
need to carry out certain hardware modifications before installing the module.
The MVME7100 provides software control over most options: by setting bits in control registers
after installing the module in a system, you can modify its configuration. The MVME7100 control
registers are described in the MVME7100 Programmer’s Reference.
Prior to installing PMC modules on the MVME7100 baseboard, ensure that all switches that are
user configurable are set properly. To do this, refer to Figure 2-3 or the board itself, for the
location of specific switches and set the switches according to the following descriptions.
Figure 2-3 Switch Locations
S1
S2
36
MVME7100 Single Board Computer Installation and Use (6806800E08A)
SMT Configuration Switch, S1
Hardware Preparation and Installation
The following sections describe the on-board switches and their configurations for the
MVME7100.
Board Malfunction
Switches marked as “reserved” might carry production-related functions and can
cause the board to malfunction if their setting is changed.
Do not change settings of switches marked as “reserved”. The setting of switches
which are not marked as “reserved” has to be checked and changed before board
installation.
2.4.1
SMT Configuration Switch, S1
An 8-position SMT configuration switch (S1) is located on the MVME7100 to control the flash
bank write-protect, select the flash boot image, and control the safe start ENV settings. The
default setting on all switch positions is OFF and is indicated by brackets in Table 2-5.
Figure 2-4 SMT Configuration Switch Position
1
Normal ENV
Boot Block A
1
2
3
4
5
6
7
8
ON
WP Disabled
Normal Operation
Normal Operation
PMC 133 MHz
Master WP
Reserved
Table 2-5 Configuration Switch Settings (S1)
Switch
Description
Setting
Function
1
S1-1
Safe Start
[OFF]
ON
Use normal ENV
Use safe ENV
S1-2
S1-3
S1-4
Boot Block B
Select
[OFF]
ON
Flash memory map normal and boot block A selected
Boot block B selected, mapped to highest address
Flash Bank WP
[OFF]
ON
Entire flash not write-protected
Flash is write-protected
JTAG Pass Thru [OFF]
ON
Normal operation
Pass-Thru mode
37
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Hardware Preparation and Installation
SMT Configuration Switch, S1
Table 2-5 Configuration Switch Settings (S1) (continued)
Switch
Description
Setting
Function
S1-5
CORE1 Low
Memory Offset
[OFF]
ON
Normal operation
S1-6
S1-7
S1-8
PMC 133 MHz
Master WP
Reserved
[OFF]
ON
PMC 100 MHz maximum
PMC 133 MHz maximum
[OFF]
ON
Master write protect disabled
Master write protect enabled
1. Switch status is readable from System Status Register 1, bit 5.
2.4.1.1 Safe Start Switch
When the SAFE_START switch is OFF, it indicates that the normal ENV setting should be used.
When the switch is set to ON, GEVs, VPD, and SPD settings are ignored and known, safe,
values are used.
2.4.1.2 Boot Block B Select
When the switch is OFF, the flash memory map is normal and block A is selected as shown in
Figure 3. When the switch is ON, block B is mapped to the highest address.
2.4.1.3 Flash Bank Write Protect
When the FLASH BANK WP switch is OFF, it indicates that the entire NOR flash is not write-
protected. NOR flash is used for executing code. When the switch is ON, it indicates that the
flash is write-protected and any writes to the flash devices are blocked by hardware.
2.4.1.4 JTAG Pass-Thru
The JTAG Pass-Thru switch is in the OFF position for normal operation. The switch is ON for
pass-through mode.
2.4.1.5 Low Memory Offset
The CORE1 Low Memory Offset switch is in the OFF position for normal operation. The switch
is ON for enabling this feature.
2.4.1.6 PMC 133 MHz
The PMC 133 MHz switch is OFF for normal operation. When the switch is ON, the maximum
frequency of operation for the PMC sites is 133 MHz. 133 MHz operation should not be enabled
unless the PMC modules are designed to support 133 MHz operation. When the switch is OFF,
the maximum frequency is 100 MHz.
38
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Geographical Address Switch, S2
Hardware Preparation and Installation
2.4.1.7 Master WP
The Master Write Protect (WP) switch is OFF for normal operation. When this switch is ON,
2
writes to the NOR Flash, NAND Flash, MRAM and I C EEPROMs are disabled. When the
switch is OFF, writes to the non-volatile devices may be allowed depending on other switches
and control bits.
2.4.2
Geographical Address Switch, S2
The Tsi148 VMEbus Status Register provides the VMEbus geographical address of the
MVME7100. Applications not using the 5-row backplane can use the geographical address
switch to assign a geographical address per the following diagram. More information regarding
GA address switch assignments can be found in the MVME7100 Single Board Computer
Programmer’s Reference.
Figure 2-5 Geographical Address Switch Position
2.4.3
VME System Controller Select, S2
Positions 1 and 2 of S2 are used to select VME System Controller selection. The default is for
automatic determination of SYSCON.
Table 2-6 VME System Controller and GA Switch Settings
Position
S2-1
Function
Default
1
VME SCON Auto
Auto-SCON
2
S2-2
VME SCON SEL
Non-SCON
S2-3
GAP
GA4
GA3
GA2
GA1
1
1
1
1
1
S2-4
S2-5
S2-6
S2-7
39
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Hardware Preparation and Installation
Installing Accessories
Table 2-6 VME System Controller and GA Switch Settings (continued)
Position
Function
Default
S2-8
GA0
1
1. The VME SCON MAN switch is OFF to select Auto-SCON mode. The switch is ON to select manual SCON mode
which works in conjunction with the VME SCON SEL switch.
2. The VME SCON SEL switch is OFF to select non-SCON mode. The switch is ON to select always SCON mode.
This switch is only effective when the VME SCON MAN switch is ON.
If you are installing the optional MVME7216E transition module, refer to Transition Module on
page 40 for configuration switch settings.
2.5 Installing Accessories
This section describes the procedures for installing the MVME7216E transition module, PMCs,
and the XMCspan on the baseboard.
2.5.1
Transition Module
The MVME7216E does not support hot swap, You should remove power to the rear slot or
system before installing the module. Before installing the MVME7216E transition module, you
may need to manually configure the switch and install a PMC I/O Module (PIM). Refer to
Chapter 5, Transition Module, for switch settings and PIM installation.
Damage of Circuits
Electrostatic discharge and incorrect installation and removal can damage circuits or
shorten their life.
Before touching the board or electronic components, make sure that you are working
in an ESD-safe environment.
Product Damage
Only use injector handles for board insertion to avoid damage to the front panel
and/or PCB. Deformation of the front panel can cause an electrical short or other
board malfunction.
Board Malfunction
Switches marked as “reserved” might carry production-related functions and can
cause the board to malfunction if their setting is changed.
Do not change settings of switches marked as “reserved”. The setting of switches
which are not marked as “reserved” has to be checked and changed before board
installation.
40
MVME7100 Single Board Computer Installation and Use (6806800E08A)
PMC
Hardware Preparation and Installation
Installation and Removal Procedure
To begin the installation of the transition module in a chassis, proceed as follows:
1. Turn all equipment power OFF and disconnect the power cable from the AC power
source.
2. Remove the chassis cover as instructed in the equipment user's manual.
3. Remove the filler panel(s) from the appropriate card slot(s) at the rear of the chassis
(if the chassis has a rear card cage).
4. Install the top and bottom edge of the transition module into the rear guides of the
chassis.
5. Ensure that the levers of the two injector/ejectors are in the outward position.
6. Slide the transition module into the chassis until resistance is felt.
7. Simultaneously move the injector/ejector levers in an inward direction.
8. Verify that the transition module is properly seated and secure it to the chassis using
the two screws located adjacent to the injector/ejector levers.
9. Connect the appropriate cables to the transition module.
To remove the transition module from the chassis, reverse the procedure and press the red
locking tabs (IEEE handles only) to extract the board.
2.5.2
PMC
The PMC connectors are placed to support two single-width PMCs or one double-width PMC.
PMC site 1 supports front PMC I/O and rear PMC I/O via the Jn4 connector. PMC 1 I/O is routed
to the VME P2 connector. PMC site 2 only supports front PMC I/O and does not have a Jn4
connector. The PMC 1 Jn4 user I/O signals only support low-current high-speed signals and
thus do not support current-bearing power supply usage.
In most cases, the PMCs are already in place on the baseboard. The user-configured switches
are accessible with the PMCs installed. The onboard PMC sites are configured to support +3.3
V I/O PMC modules. The onboard PMC sites do not support +5.0 V I/O PMC modules.
Follow these steps to install a PMC onto the MVME7100 board.
41
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Hardware Preparation and Installation
PMC
Installation Procedure
Read all notices and follow these steps to install a PMC on the baseboard.
Damage of Circuits
Electrostatic discharge and incorrect installation and removal can damage circuits or
shorten their life.
Before touching the board or electronic components, make sure that you are working
in an ESD-safe environment.
Product Damage
Inserting or removing modules with power applied may result in damage to module
components.
Before installing or removing additional devices or modules, read the documentation
that came with the product.
1. Attach an ESD strap to your wrist. Attach the other end of the ESD strap to the
chassis as a ground. The ESD strap must be secured to your wrist and to ground
throughout the procedure.
2. Remove the PCI filler from the front panel.
3. Slide the edge connector of the PMC module into the front panel opening from
behind and place the PMC module on top of the baseboard. The four connectors on
the underside of the PMC module should then connect smoothly with the
corresponding connectors on the MVME7100.
4. Insert the four short phillips-head screws (provided with the PMC) through the holes
on the bottom side of the MVME7100 and the PMC front bezel and into rear
standoffs. Tighten the screws. Refer to Figure 2-6 on page 43.
5. Reinstall the MVME7100 assembly in its proper card slot. Be sure the module is well
seated in the backplane connectors. Do not damage or bend connector pins.
6. If the PMC module was installed in a non-hot swap chassis, replace the chassis or
system cover(s), reconnect the system to the AC or DC power source and turn the
equipment power on.
42
MVME7100 Single Board Computer Installation and Use (6806800E08A)
XMCspan
Hardware Preparation and Installation
Figure 2-6 Typical Placement of a PMC Module on a VME Module
2.5.3
XMCspan
The XMCspan is a carrier module that provides PCI Express expansion capability to the
MVME7100. Refer to the XMCspan Installation and Use manual (part number 6806800H03) for
details about the XMCspan and the installation procedure.
2.6 Installing and Removing the Board
This section describes a recommended procedure for installing a board module in a chassis.
The MVME7100 does not support hot swap, you should remove power to the slot or system
before installing the module. Before installing the MVME7100, ensure that the serial ports and
switches are properly configured.
43
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Hardware Preparation and Installation
Installing and Removing the Board
Installation and Removal Procedure
Before you install your module, please read all cautions, warnings and instructions presented
in this section.
Damage of Circuits
Electrostatic discharge and incorrect installation and removal can damage circuits or
shorten their life.
Before touching the board or electronic components, make sure that you are working
in an ESD-safe environment.
Product Damage
Only use injector handles for board insertion to avoid damage to the front panel
and/or PCB. Deformation of the front panel can cause an electrical short or other
board malfunction.
Use the following steps to install the MVME7100 into your computer chassis.
1. Attach an ESD strap to your wrist. Attach the other end of the ESD strap to an
electrical ground. The ESD strap must be secured to your wrist and to ground
throughout the procedure.
2. Remove any filler panel that might fill that slot.
3. Install the top and bottom edge of the MVME7100 into the guides of the chassis.
4. Ensure that the levers of the two injector/ejectors are in the outward position.
5. Slide the MVME7100 into the chassis until resistance is felt.
6. Simultaneously move the injector/ejector levers in an inward direction.
7. Verify that the MVME7100 is properly seated and secure it to the chassis using the
two screws located adjacent to the injector/ejector levers.
8. Connect the appropriate cables to the MVME7100.
To remove the board from the chassis, reverse the procedure and press the red locking tabs
(IEEE handles only) to extract the board.
44
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Completing the Installation
Hardware Preparation and Installation
2.7 Completing the Installation
The MVME7100 is designed to operate as an application-specific compute blade or an
intelligent I/O board/carrier. It can be used in any slot in a VME chassis. When the MVME7100
is installed in a chassis, you are ready to connect peripherals and apply power to the board.
Figure 3-1 on page 47 and Figure 5-1 on page 75 show the locations of the various connectors
on the MVME7100 and MVME7216E.
Product Damage
RJ-45 connectors on modules are either twisted-pair Ethernet (TPE) or E1/T1/J1
network interfaces. Connecting an E1/T1/J1 line to an Ethernet connector may
damage your system.
z
z
z
Make sure that TPE connectors near your working area are clearly marked as
network connectors.
Verify that the length of an electric cable connected to a TPE bushing does not
exceed 100 meters.
Make sure the TPE bushing of the system is connected only to safety extra low
voltage circuits (SELV circuits).
If in doubt, ask your system administrator.
The console settings for the MVME7100 are:
z
z
z
z
Eight bits per character
One stop bit per character
Parity disabled (no parity)
Baud rate of 9600 baud
Verify that hardware is installed and the power/peripheral cables connected are appropriate for
your system configuration.
Replace the chassis or system cover, reconnect the chassis to the AC or DC power source, and
turn the equipment power on.
2.8 Factory Installed Linux
A bootable ramdisk based Linux image based on the 2.6.25 kernel is available in NOR flash. To
boot this image, use the following MOTLOAD commands:
MVME7100> bmw -af8000000 -bf8f00000 -c4000000
MVME7100> execP -l4000400
The image should boot to the following prompt:
45
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Hardware Preparation and Installation
Factory Installed Linux
Emerson Network Power Embedded Computing Linux
Kernel 2.6.25 on a 2-processor MVME7100
localhost login:
Login as root.
The /root/README.MVME7100_LINUXfile provides a brief overview of MVME7100 Linux.
Contact Emerson Network Power Embedded Computing for kernel patches and additional
information on using MVME7100 Linux.
46
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Controls, LEDs, and Connectors
3
3.1 Overview
This chapter summarizes the controls, LEDs, connectors, and headers for the MVME7100
baseboard. Connectors for the MVME7216E transition module can be found in Rear Panel
Connectors on page 77.
3.2 Board Layout
The following figure shows the components, LEDs, connectors, and the reset switch on the
MVME7100.
Figure 3-1 Component Layout
J21 J22
S1
S2
P1
J23
J11
J12
J13
J14
Battery
P2
Heat Sink
J3
J2
J4A/J4B
47
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Controls, LEDs, and Connectors
Front Panel
3.3 Front Panel
The following switch, LEDs, and connectors are available on the MVME7100 front panel. Refer
to Figure 3-1 for the location of each.
Figure 3-2 Front Panel LEDs, Connectors, Switch
PMC 2
PMC 1
USER 1
ABT/RST
COMM 1
USB
FAIL
SPEED
GENET 1
GENET 2
ACT
SPEED
ACT
3.3.1
Reset/Abort Switch
The MVME7100 has a single push button switch to provide both the abort and reset functions.
When the switch is depressed for less than 3 seconds, an abort interrupt is generated to the
MC8641D PIC. If the switch is held for more than 3 seconds, a board hard reset is generated.
If the MVME7100 is the VMEbus system controller, a VME SYSRESET is generated.
48
MVME7100 Single Board Computer Installation and Use (6806800E08A)
LEDs
Controls, LEDs, and Connectors
3.3.2
LEDs
The next table describes the LEDs on the front panel of the MVME7100. Refer to Figure 3-1
on page 47 for LED locations.
Table 3-1 Front Panel LEDs
Label
Function
Location
Color
Description
BFL
Board Fail
Front panel Red
This indicator is illuminated
during a hard reset and
remains illuminated until
software turns it off. The LED
is controlled by bit 14
(BDFAIL) of the VSTAT
register in the Tsi148.
USR1
User Defined
Front panel Red/Yellow
This indicator is illuminated
by S/W assertion of its
corresponding register bits in
the Status Indicator Register.
See the Programmer's Guide
for further detail.
GNET1
SPEED
TSEC1 Link / Speed
Front panel Off
Yellow
No link
10/100 BASE-T operation
1000 BASE-T operation
Green
GNET1 ACT
TSEC1Activity
Front panel Off
No activity
Blinking Green Activity proportional to
bandwidth utilization
GNET2
SPEED
TSEC2 Link / Speed
Front panel Off
No link
Yellow
Green
10/100 BASE-T operation
1000 BASE-T operation
GNET2 ACT
TSEC2 Activity
Front panel Off
No activity
Blinking Green Activity proportional to
bandwidth utilization
49
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Controls, LEDs, and Connectors
Connectors
3.3.3
Connectors
This section describes the pin assignments and signals for the connectors on the MVME7100.
The next table lists the standard connectors on the MVME7100 baseboard. Refer to Figure 3-1
on page 47 for connector locations. Pin assignments for the connectors are in the following
sections. Some connectors use standard pin assignments in compliance with the VMEbus,
IEEE, PCI, and ANSI/VITA specifications. Links to these specifications are located at Appendix
B, Related Specifications, on page 103.
Table 3-2 Baseboard Connectors
Reference
Designator
Function
Notes
J6
XMC Expansion
8X PCI-E to XMCSpan
J4A
J4B
TSEC 1, 10/100/1000 Ethernet
TSEC 2, 10/100/1000 Ethernet
RJ-45
RJ-45
J11, J12, J13, J14
J21, J22, J23
PMC1
PMC2
Implementing all recommended and
optional VITA32 signals except
RESETOUT#
J1
Port 0. Serial Port 1
VME five-row P1
Mini DB-9 console serial port
P1
P2
VME five-row P2 on SBC and
RTM
TSEC3 signals assigned to E1-1 thru
E1-4
TSEC4 signals assigned to E2-1 thru
E2-4
Serial ports 2-5
J2
USB
Single channel upright USB connector.
USB1 on front
P4
P5
Processor COP header
Boundary Scan header
50
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Connectors
Controls, LEDs, and Connectors
3.3.3.1 XMC Expansion Connector (J6)
One 76-pin Mictor connector with a center row of ground pins is used to provide XMC expansion
capability. The pin assignments for this connector are as follows:
Table 3-3 XMC Expansion Connector (J6) Pin Assignments
Pin
1
Signal
GND
Signal
Pin
2
GND
GND
3
TX0_P
TX0_N
GND
RX0_P
RX0_N
GND
4
5
6
7
8
9
TX1_P
TX1_N
GND
RX1_P
RX1_N
GND
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
11
13
15
17
19
21
23
25
27
29
31
33
35
37
TX2_P
TX2_N
GND
RX2_P
RX2_N
GND
TX3_P
TX3_N
GND
RX3_P
RX3_N
GND
REFCLK_P
REFCLK_N
GND
No Connect
No Connect
GND
No Connect
No Connect
INT_N
No Connect
PCIE_END_N
RESET_N
51
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Controls, LEDs, and Connectors
Connectors
Table 3-3 XMC Expansion Connector (J6) Pin Assignments (continued)
Pin
39
41
43
45
47
49
51
53
55
57
59
61
63
65
67
69
71
73
75
Signal
GND
Signal
Pin
40
42
44
46
48
50
52
54
56
58
60
62
64
66
68
70
72
74
76
+5V
GND
TX4_P
TX4_N
GND
RX4_P
RX4_N
GND
TX5_P
TX5_N
GND
RX5_P
RX5_N
GND
TX6_P
TX6_N
GND
RX6_P
RX6_N
GND
TX7_P
TX7_N
GND
RX7_P
RX7_N
GND
No Connect
No Connect
TDI
No Connect
No Connect
TDO
TRST_N
TMS
I2C_CLK
I2C_DATA
PRESENT_N
TCK
3.3.3.2 Ethernet Connectors (J4A/J4B)
There are four 10/100/1000 Mb/s full duplex Ethernet interfaces using the MC8641D Triple
Speed Ethernet Controllers (TSECs). Two Gigabit Ethernet interfaces are routed to the two
front-panel RJ-45 connectors with integrated LEDs for speed and activity indication. The other
Gigabit Ethernet interfaces are routed to P2 for rear I/O. These connectors use standard pin
assignments and are as follows:
Table 3-4 Ethernet Connectors (J4A/J4B) Pin Assignments
Pin #
10/100/1000 Mb/s
_DA+
1
2
3
4
5
6
7
_DA-
_DB+
_DC+
_DC-
_DB-
_DD+
52
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Connectors
Controls, LEDs, and Connectors
Table 3-4 Ethernet Connectors (J4A/J4B) Pin Assignments (continued)
Pin #
10/100/1000 Mb/s
8
_DD-
3.3.3.3 PCI Mezzanine Card (PMC) Connectors (J11 – J14, J21 – J23)
There are seven 64-pin SMT connectors on the MVME7100 to provide 32/64-bit PCI interfaces
and P2 I/O for one optional add-on PMC.
PMC slot connector J14 contains the signals that go to VME P2 I/O rows A, C, D, and Z.
The pin assignments for these connectors are as follows:
Table 3-5 PMC Slot 1 Connector (J11) Pin Assignments
Pin
1
Signal
TCK
Signal
-12V
Pin
2
3
GND
INTA#
INTC#
+5V
4
5
INTB#
6
7
PMCPRSNT1#
INTD#
8
9
PCI_RSVD
+3.3Vaux
GND
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
GND
CLK
GND
PMCGNT1#
+5V
PMCREQ1#
+3.3V (VIO)
AD28
AD31
AD27
AD25
GND
GND
C/BE3#
AD21
AD22
AD19
+5V
+3.3V (VIO)
FRAME#
GND
AD17
GND
IRDY#
+5V
DEVSEL#
GND
LOCK#
PCI_RSVD
GND
PCI_RSVD
PAR
+3.3V (VIO)
AD12
AD15
AD11
AD09
+5V
53
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Controls, LEDs, and Connectors
Connectors
Table 3-5 PMC Slot 1 Connector (J11) Pin Assignments (continued)
Pin
51
53
55
57
59
61
63
Signal
GND
Signal
C/BE0#
AD05
GND
Pin
52
54
56
58
60
62
64
AD06
AD04
+3.3V (VIO)
AD02
AD03
AD01
+5V
AD00
GND
REQ64#
Table 3-6 PMC Slot 1 Connector (J12) Pin Assignments
Pin
1
Signal
+12V
Signal
TRST#
TDO
Pin
2
3
TMS
4
5
TDI
GND
6
7
GND
Not Used
Not Used
+3.3V
8
9
Not Used
Pull-up
RST#
+3.3V
Not Used
AD30
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
Pull-down
Pull-down
GND
AD29
GND
AD26
AD24
+3.3V
IDSEL1
+3.3V
AD18
AD23
AD20
GND
AD16
C/BE2#
IDSEL1B
+3.3V
GND
TRDY#
GND
STOP#
GND
PERR#
+3.3V
C/BE1#
AD14
SERR#
GND
AD13
M66EN
AD08
AD10
+3.3V
54
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Connectors
Controls, LEDs, and Connectors
Table 3-6 PMC Slot 1 Connector (J12) Pin Assignments (continued)
Pin
51
53
55
57
59
61
63
Signal
AD07
Signal
Pin
52
54
56
58
60
62
64
REQ1B#
+3.3V
GNT1B#
Not Used
Not Used
GND
GND
EREADY0
Not Used
+3.3V
ACK64#
GND
No Connect (MONARCH#)
Table 3-7 PMC Slot 1 Connector (J13) Pin Assignments
Pin
1
Signal
Reserved
GND
Signal
GND
Pin
2
3
C/BE7#
C/BE5#
GND
4
5
C/BE6#
C/BE4#
+3.3V (VIO)
AD63
6
7
8
9
PAR64
AD62
GND
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
AD61
GND
AD60
AD58
GND
AD59
AD57
+3.3V (VIO)
AD55
AD56
AD54
GND
AD53
GND
AD52
AD50
GND
AD51
AD49
GND
AD48
AD46
GND
AD47
AD45
+3.3V (VIO)
AD43
AD44
AD42
GND
AD41
GND
AD40
AD38
GND
AD39
AD37
55
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Controls, LEDs, and Connectors
Connectors
Table 3-7 PMC Slot 1 Connector (J13) Pin Assignments (continued)
Pin
51
53
55
57
59
61
63
Signal
GND
Signal
AD36
Pin
52
54
56
58
60
62
64
AD35
AD34
AD33
GND
+3.3V (VIO)
Reserved
Reserved
GND
AD32
Reserved
GND
Reserved
Table 3-8 PMC Slot 1 Connector (J14) Pin Assignments
Pin
1
Signal
Signal
Pin
2
PMC1_1 (P2-C1)
PMC1_3 (P2-C2)
PMC1_5 (P2-C3)
PMC1_7 (P2-C4)
PMC1 _9 (P2-C5)
PMC1_11 (P2-C6)
PMC1_13 (P2-C7)
PMC1_15 (P2-C8)
PMC1_17 (P2-C9)
PMC1_19 (P2-C10)
PMC1PMC1_21 (P2-C11)
PMC1_23 (P2-C12)
PMC1_25 (P2-C13)
PMC1_27 (P2-C14)
PMC1_29 (P2-C15)
PMC1_31 (P2-C16)
PMC1_33 (P2-C17)
PMC1_35 (P2-C18)
PMC1_37 (P2-C19)
PMC1_39 (P2-C20)
PMC1_41 (P2-C21)
PMC1_43 (P2-C22)
PMC1_45 (P2-C23)
PMC1_47 (P2-C24)
PMC1_49 (P2-C25)
PMC1_2 (P2-A1)
PMC1_4 (P2-A2)
PMC1_6 (P2-A3)
PMC1_8 (P2-A4)
PMC1_10 (P2-A5)
PMC1_12 (P2-A6)
PMC1_14 (P2-A7)
PMC1_16 (P2-A8)
PMC1_18 (P2-A9)
PMC1_20 (P2-A10)
PMC1_22 (P2-A11)
PMC1_24 (P2-A12)
PMC1_26 (P2-A13)
PMC1_28 (P2-A14)
PMC1_30 (P2-A15)
PMC1_32 (P2-A16)
PMC1_34 (P2-A17)
PMC1_36 (P2-A18)
PMC1_38 (P2-A19)
PMC1_40 (P2-A20)
PMC1_42 (P2-A21)
PMC1_44 (P2-A22)
PMC1_46 (P2-A23)
PMC1_48 (P2-A24)
PMC1_50 (P2-A25)
3
4
5
6
7
8
9
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
56
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Connectors
Controls, LEDs, and Connectors
Table 3-8 PMC Slot 1 Connector (J14) Pin Assignments (continued)
Pin
51
53
55
57
59
61
63
Signal
Signal
Pin
52
54
56
58
60
62
64
PMC1_51 (P2-C26)
PMC1_53 (P2-C27)
PMC1_55 (P2-C28)
PMC1_57 (P2-C29)
PMC1_59 (P2-C30)
PMC1_61 (P2-C31)
PMC1_63 (P2-C32)
PMC1_52 (P2-A26)
PMC1_54 (P2-A27)
PMC1_56 (P2-A28)
PMC1_58 (P2-A29)
PMC1_60 (P2-A30)
PMC1_62 (P2-A31)
PMC1_64 (P2-A32)
Table 3-9 PMC Slot 2 Connector (J21) Pin Assignments
Pin
1
Signal
TCK
Signal
-12V
Pin
2
3
GND
INTC#
INTA#
+5V
4
5
INTD#
6
7
PMCPRSNT1#
INTB#
8
9
PCI_RSVD
+3.3Vaux
GND
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
GND
CLK
GND
PMCGNT1#
+5V
PMCREQ1#
+3.3V (VIO)
AD28
AD31
AD27
AD25
GND
GND
C/BE3#
AD21
AD22
AD19
+5V
+3.3V (VIO)
FRAME#
GND
AD17
GND
IRDY#
+5V
DEVSEL#
GND
LOCK#
PCI_RSVD
GND
PCI_RSVD
PAR
+3.3V (VIO)
AD12
AD15
AD11
AD09
+5V
57
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Controls, LEDs, and Connectors
Connectors
Table 3-9 PMC Slot 2 Connector (J21) Pin Assignments (continued)
Pin
51
53
55
57
59
61
63
Signal
GND
Signal
C/BE0#
AD05
GND
Pin
52
54
56
58
60
62
64
AD06
AD04
+3.3V (VIO)
AD02
AD03
AD01
+5V
AD00
GND
REQ64#
Table 3-10 PMC Slot 2 Connector (J22) Pin Assignments
Pin
1
Signal
+12V
Signal
TRST#
TDO
Pin
2
3
TMS
4
5
TDI
GND
6
7
GND
Not Used
Not Used
+3.3V
8
9
Not Used
Pull-up
RST#
+3.3V
Not Used
AD30
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
Pull-down
Pull-down
GND
AD29
GND
AD26
AD24
+3.3V
IDSEL1
+3.3V
AD18
AD23
AD20
GND
AD16
C/BE2#
IDSEL1B
+3.3V
GND
TRDY#
GND
STOP#
GND
PERR#
+3.3V
C/BE1#
AD14
SERR#
GND
AD13
M66EN
AD08
AD10
+3.3V
58
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Connectors
Controls, LEDs, and Connectors
Table 3-10 PMC Slot 2 Connector (J22) Pin Assignments (continued)
Pin
51
53
55
57
59
61
63
Signal
AD07
Signal
Pin
52
54
56
58
60
62
64
REQ1B#
+3.3V
GNT1B#
Not Used
Not Used
GND
GND
EREADY1
Not Used
+3.3V
ACK64#
GND
No Connect (MONARCH#)
Table 3-11 PMC Slot 2 Connector (J23) Pin Assignments
Pin
1
Signal
Reserved
GND
Signal
GND
Pin
2
3
C/BE7#
C/BE5#
GND
4
5
C/BE6#
C/BE4#
+3.3V (VIO)
AD63
6
7
8
9
PAR64
AD62
GND
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
AD61
GND
AD60
AD58
GND
AD59
AD57
+3.3V (VIO)
AD55
AD56
AD54
GND
AD53
GND
AD52
AD50
GND
AD51
AD49
GND
AD48
AD46
GND
AD47
AD45
+3.3V (VIO)
AD43
AD44
AD42
GND
AD41
GND
AD40
AD38
GND
AD39
AD37
59
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Controls, LEDs, and Connectors
Connectors
Table 3-11 PMC Slot 2 Connector (J23) Pin Assignments (continued)
Pin
51
53
55
57
59
61
63
Signal
GND
Signal
AD36
Pin
52
54
56
58
60
62
64
AD35
AD34
AD33
GND
+3.3V (VIO)
Reserved
Reserved
GND
AD32
Reserved
GND
Reserved
3.3.3.4 Serial Port Connector (COM1/J1)
There is one front access asynchronous serial port interface (SP0) that is routed to the
mini DB-9 front-panel connector. The pin assignments for these connectors are as follows:
Table 3-12 COM1 Port Connector Pin Assignments
Pin
1
Signal
No connect
RX
2
3
TX
4
No Connect
GND
5
6
No Connect
RTS
7
8
CTS
9
No Connect
3.3.3.5 VMEbus P1 Connector
The VME P1 connector is a 160-pin DIN. The P1 connector provides power and VME signals
for 24-bit address and 16-bit data. The pin assignments for the P1 connector is as follows:
Table 3-13 VMEbus P1 Connector Pin Assignments
ROW Z
Reserved
GND
ROW A
D00
ROW B
BBSY*
ROW C
D08
ROW D
+5V
1
2
3
4
5
6
1
2
3
4
5
6
D01
BCLR*
D09
GND
Reserved
GND
D02
ACFAIL*
BG0IN*
BG0OUT*
BG1IN*
D10
Reserved
Reserved
Reserved
Reserved
D03
D11
Reserved
GND
D04
D12
D05
D13
60
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Connectors
Controls, LEDs, and Connectors
Table 3-13 VMEbus P1 Connector Pin Assignments (continued)
ROW Z
Reserved
GND
ROW A
D06
ROW B
BG1OUT*
BG2IN*
BG2OUT*
BG3IN*
BG3OUT*
BR0*
ROW C
ROW D
7
D14
Reserved
Reserved
GAP_L
7
8
D07
D15
8
9
Reserved
GND
GND
SYSCLK
GND
DS1*
DS0*
WRITE*
GND
DTACK*
GND
AS*
GND
SYSFAIL*
BERR*
SYSRESET*
LWORD*
AM5
A23
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
GA0_L
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
Reserved
GND
GA1_L
Reserved
GA2_L
Reserved
GND
BR1*
BR2*
Reserved
GA3_L
Reserved
GND
BR3*
AM0
A22
Reserved
GA4_L
Reserved
GND
AM1
A21
AM2
A20
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
GND
Reserved
GND
GND
IACK*
IACKIN*
IACKOUT*
AM4
AM3
A19
GND
A18
Reserved
GND
SERA
SERB
GND
A17
A16
Reserved
GND
A15
A07
IRQ7*
IRQ6*
IRQ5*
IRQ4*
IRQ3*
IRQ2*
IRQ1*
+5VSTDBY
+5V
A14
Reserved
GND
A06
A13
A05
A12
Reserved
GND
A04
A11
A03
A10
Reserved
GND
A02
A09
A01
A08
Reserved
GND
-12V
+12V
+5V
+5V
+5V
3.3.3.6 VMEbus P2 Connector
The VME P2 connector is a 160-pin DIN. Row B of the P2 connector provides power to the
MVME7100 and to the upper eight VMEbus address lines and additional 16 VMEbus data lines.
The Z, A, C, and D pin assignments for the P2 connector are the same for both the MVME7100
and MVME7216E, and are as follows:
Table 3-14 VME P2 Connector Pinouts
Pin
P2-Z
P2-A
P2-B
P2-C
P2-D
1
SP1RX
PMC1_IO2
+5V
PMC1_IO1
E1-1+
61
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Controls, LEDs, and Connectors
Connectors
Table 3-14 VME P2 Connector Pinouts (continued)
Pin
2
P2-Z
P2-A
P2-B
GND
P2-C
P2-D
GND
PMC1_IO4
PMC1_IO6
PMC1_IO8
PMC1_IO10
PMC1_IO12
PMC1_IO14
PMC1_IO16
PMC1_IO18
PMC1_IO20
PMC1_IO22
PMC1_IO24
PMC1_IO26
PMC1_IO28
PMC1_IO30
PMC1_IO32
PMC1_IO34
PMC1_IO36
PMC1_IO38
PMC1_IO40
PMC1_IO42
PMC1_IO44
PMC1_IO46
PMC1_IO48
PMC1_IO50
PMC1_IO52
PMC1_IO54
PMC1_IO56
PMC1_IO58
PMC1_IO60
PMC1_IO62
PMC1_IO64
PMC1_IO3
PMC1_IO5
PMC1_IO7
PMC1_IO9
PMC1_IO11
PMC1_IO13
PMC1_IO15
PMC1_IO17
PMC1_IO19
PMC1_IO21
PMC1_IO23
PMC1_IO25
PMC1_IO27
PMC1_IO29
PMC1_IO31
PMC1_IO33
PMC1_IO35
PMC1_IO37
PMC1_IO39
PMC1_IO41
PMC1_IO43
PMC1_IO45
PMC1_IO47
PMC1_IO49
PMC1_IO51
PMC1_IO53
PMC1_IO55
PMC1_IO57
PMC1_IO59
PMC1_IO61
PMC1_IO63
E1-1-
3
SPITX
GND
VRETRY_L
VA24
VA25
VA26
VA27
VA28
VA29
VA30
VA31
GND
GND
4
E1-2+
E1-2-
5
SP1CTS
GND
6
GND
7
SP1RTS
GND
E1-3+
E1-3-
8
9
SP2RX
GND
GND
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
E1-4+
E1-4-
SP2TX
GND
GND
SP2CTS
GND
+5V
I2C_SDA
I2C_SCL
E1_LINK
E1_ACT
E2_LINK
E2_ACT
GND
VD16
VD17
VD18
VD19
VD20
VD21
VD22
VD23
GND
SP2RTS
GND
SP3RX
GND
SP3TX
GND
E2-4-
SP3CTS
GND
E2-4+
GND
SP3RTS
GND
VD24
VD25
VD26
VD27
VD28
VD29
VD30
VD31
GND
E2-3-
E2-3+
GND
SP4RX
GND
E2-2-
SP4TX
GND
E2-2+
GND
SP4CTS
GND
E2-1-
E2-1+
GND
SP4RTS
GND
+5V
+5V
62
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Connectors
Controls, LEDs, and Connectors
3.3.3.7 MVME7216E PMC I/O Module (PIM) Connectors (J10, J14)
PMC Host I/O connector J10 routes only power and ground from VME P2. There are no Host
I/O signals on this connector. The MVME7100 routes PMC I/O from J14 of PMC Slot 1 to VME
P2 rows A and C. The MVME7216E routes these signals (pin-for-pin) from VME P2 to PMC I/O
Module connector J14. See Table 3-15 and Table 3-8 for the pin assignments.
Table 3-15 MVME721 Host I/O Connector (J10) Pin Assignments
Pin
1
Signal
Signal
Pin
2
No Connect
No Connect
+5V
No Connect
No Connect
No Connect
No Connect
+3.3V
3
4
5
6
7
No Connect
No Connect
No Connect
GND
8
9
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
No Connect
No Connect
No Connect
GND
No Connect
No Connect
No Connect
+5V
No Connect
No Connect
No Connect
+3.3V
No Connect
No Connect
No Connect
GND
No Connect
No Connect
No Connect
GND
No Connect
No Connect
No Connect
+5V
No Connect
No Connect
No Connect
+3.3V
No Connect
No Connect
No Connect
GND
No Connect
No Connect
No Connect
GND
No Connect
No Connect
No Connect
+5V
No Connect
No Connect
No Connect
+3.3V
No Connect
No Connect
No Connect
No Connect
63
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Controls, LEDs, and Connectors
Headers
Table 3-15 MVME721 Host I/O Connector (J10) Pin Assignments (continued)
Pin
61
Signal
Signal
Pin
62
No Connect
No Connect
No Connect
No Connect
63
64
3.3.3.8 USB Connector (J2)
There is one USB Type A connector located on the MVME7100 front panel. The pin
assignments are as follows:
Table 3-16 USB Connector (J2) Pin Assignments
Pin
1
Signal
USB_VBUS (+5.0V)
USB_DATA-
USB_DATA+
GND
2
3
4
3.4 Headers
This section describes the pin assignments of the Headers on the MVME7100.
3.4.1
Processor COP Header (P4)
There is one standard 16-pin header that provides access to the COP function. The pin
assignments for this header are as follows:
Table 3-17 Processor COP Header (P4) Pin Assignments
Pin
1
Signal
Signal
Pin
2
CPU_TDO
CPU_TDI
No Connect
CPU_TRST_L
CPU_VIO (+3.3V)
CPU_CKSTPI_L
No Connect
GND
3
4
5
Pullup
6
7
CPU_TCK
CPU_TMS
CPU_SRST_L
CPU_HRST_L
CPU_CKSTPO_L
8
9
10
12
14
16
11
13
15
KEY (no pin)
GND
Pin 6 +3.3V has a 100 Ω resistor to +3.3V.
64
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Boundary Scan Header (P5)
Controls, LEDs, and Connectors
3.4.2
Boundary Scan Header (P5)
The 20-pin boundary scan header provides an interface for programming the on-board PLDs
and for boundary scan testing/debug purposes. The pin assignments for this header are as
follows:
Table 3-18 Boundary Scan Header (P5) Pin Assignments
Pin
1
Signal
TCK
Signal
Pin
2
GND
3
TDO
GND
4
5
TMS
GND
6
7
TRST_N
TDI
GND
8
9
(BSCANEN_N)
No Connect
AUTOWR_N
No Connect
No Connect
No Connect
10
12
14
16
18
20
11
13
15
17
19
KEY
GND
GND
GND
GND
Pin 10 must be grounded in the cable in order to enable boundary scan.
65
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Controls, LEDs, and Connectors
Boundary Scan Header (P5)
66
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Functional Description
4
4.1 Overview
The MVME7100 VMEbus board is based on the MC8640D (1.067 GHz versions) and the
MC8641D (1.33 GHz versions) Integrated Processors. The MVME7100 provides front panel
access to one serial port with a mini DB-9 connector, two 10/100/1000 Ethernet ports with two
RJ-45 connectors, and one USB port with one type A connector. The front panel includes a fail
indicator LED, user-defined indicator LED, and a reset/abort switch.
The MVME7216E transition module provides rear panel access to four serial ports with one
RJ-45 connector per port and two 10/100/1000 Ethernet ports with two RJ-45 connectors. The
transition module also provides two planar connectors for one PIM with front I/O.
The block diagram for the MVME7100 Single Board Computer is shown in Figure 4-1 and the
block diagram for the MVME7216E transition module is shown in Figure 5-2.
67
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Functional Description
Block Diagram
4.2 Block Diagram
The following figure is a block diagram of the MVME7100 architecture.
Figure 4-1 Block Diagram
GigE GigE
PMC1 Front IO
USB
COM
RJ-45 RJ-45
PMC2 Front IO
Front Panel
ABT/RST
Up to 4 GB
DDR2 Memory
(SPD)
PHY
5482
XCVR
RS-232
User
128 KB
VPD
8 KB
RTC
DS1375
Serial Port 0
DDR2 MC
DUART
TSEC1
TSEC2
GigE 1
I2C Bus
I2C
GigE 2
GigE 3
GIgE 4
MC864xD
Processor
Device
Bus
TSEC3
TSEC4
CPLD
Decode
Timers/Regs
Temp
MAX6649
LBC
PCI-E
-E
PCI
Serial Ports 1-4
MRAM
Flash
Flash
QUART
16C554
128 MB 4 or 8 GB 512 KB
XMCspan
PHY
5482
PCI - E
Switch
E2P
E2P
E2P
PEX8114
PEX8114
PEX8114
E2P
PEX8112
VME
Tsi148
USB
uPD720101
PMC 1
PMC 2
XCVR
22501
XCVR
VME Bus
RS-232
COM2-
COM5
PMC 1 Jn4 IO
I2C Bus
GigE 3
GigE 4
P2
P1
4.3 Processor
The MVME7100 is designed to support the MC864xD (dual e600 core) processor. The
processor is configured to operate at 1.067 GHz or 1.33 GHz core frequency with a
corresponding DDR400 Mb or DDR533 DDR2 memory bus.
68
MVME7100 Single Board Computer Installation and Use (6806800E08A)
I2C Serial Interface and Devices
Functional Description
The MVME7100 supports the power-on reset (POR) pin sampling method for processor reset
configuration. The states of the various configuration pins on the processor are sampled when
reset is de-asserted to determine the desired operating modes. Combinations of pull-up and
pull-down resistors are used to set the options. Some options are fixed and some are selectable
at build time by installing the proper pull-up/pull-down resistor. Refer to the MC864xD reference
manual, listed in Appendix B, Related Documentation, Manufacturers’ Documents on page 101
for additional details and/or programming information.
2
4.4 I C Serial Interface and Devices
2
The MVME7100 provides the following on-board I C serial devices connected to the MC864xD
2
I C controller 0 interface:
z
z
z
z
z
z
8 KB serial EEPROM for VPD
Two 64 KB serial EEPROMs for user configuration data storage
Two 256 byte serial EEPROMs for SPD
Maxim DS1375 Real Time Clock
Maxim MAX6649 temperature sensor
8 KB serial EEPROM on RTM VPD
The RTC implemented on the MVME7100 provides an alarm interrupt routed to the MC864xD
PIC through the control PLD. A DS32KHz temperature controlled crystal oscillator provides the
RTC clock reference. A battery backup circuit for the RTC is provided on-board.
The Maxim digital temperature sensor measures of temperature of the board and also connects
to the temperature diode on the MC864xD. The temperature sensor also provides an alarm
interrupt routed to the MC864xD PIC through the control PLD.
2
The I C interface is routed to the P2 connector for access to the serial EEPROM located on the
transition module. The device address for the transition module serial EEPROM is user
selectable using the configuration switches. Refer to Chapter 5, Transition Module for
information on the switches.
For programming information, see the MVME7100 Single Board Computer Programmer’s
Reference.
4.5 System Memory
The MC864xD includes two memory controllers. The MVME7100 supports one bank of
memory on each controller. The MVME7100 supports 512 MB, 1 GB and 2 GB DDR2
SDRAMS. This provides memory configurations of 1 GB, 2 GB, and 4 GB. The MVME7100
supports memory speeds up to DDR533.
69
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Functional Description
Timers
4.6 Timers
Timing functions for the MVME7100 are provided by four global high-resolution timers
integrated into the MC864xD plus four additional independent 32-bit timers.
The four integrated 32-bit timers are clocked by the RTC input which is driven by a 1 MHz clock.
Refer to the MC864xD reference manual, listed in Appendix B, Related Documentation,
Manufacturers’ Documents on page 101 for additional details and/or programming information
The clock source for the four 32-bit timers in the PLD is 25 MHz. The timer prescaler must be
configured to generate a 1 MHz timer reference. For programming information, see MVME7100
Single Board Computer Programmer’s Reference.
4.7 Ethernet Interfaces
The MVME7100 provides four 10/100/1000 Mbps full-duplex Ethernet interfaces using the
MC864xD Ethernet Controllers. Two Broadcom BCM5482S PHYs are used. The Ethernet ports
on the MC864xD are configured to operate in RGMII mode. Two Gigabit Ethernet interfaces are
routed to front panel RJ-45 connectors with integrated LEDs for speed and activity indication.
The other two Gigabit Ethernet interfaces are routed to P2 for rear I/O. For programming
information, see MVME7100 Single Board Computer Programmer’s Reference.
4.8 Local Bus Interface
The MVME7100 uses the MC864xD Local Bus Controller (LBC) for access to on-board flash
and I/O registers. The LBC has programmable timing modes to support devices of different
access times, as well as device widths of 8, 16, and 32 bits. The MVME7100 uses the LBC in
GPCM mode to interface to two physical banks of on-board flash, an on-board Quad UART
(QUART), an MRAM, and on-board 32-bit timers along with control/status registers. Access
timing for each device type is programmable and depends on the device timing data found in
the VPD during initialization.
A hardware flash bank write protect switch is provided on the MVME7100 to enable write
protection of the NOR Flash. Regardless of the state of the software flash write protect bit in the
NOR Flash Control/Status register, write protection is enabled when this switch is ON. When
this switch is OFF, write protection is controlled by the state of the software flash write protect
bits and can only be disabled by clearing this bit in the NOR Flash Control/Status register. Note
that the F_WE_HW bit reflects the state of the switch and is only software readable whereas
the F_WP_SW bit supports both read and write operations.
The MVME7100 provides a dual boot option for booting from one of two separate boot images
in the boot flash bank which are referred to as boot block A and boot block B. Boot blocks A and
B are each 1 MB in size and are located at the top (highest address) 2 MB of the boot flash
memory space. Block A is located at the highest 1 MB block and block B is the next highest 1
MB block. A flash boot block switch is used to select between boot block A and boot block B.
When the switch is OFF, the flash memory map is normal and block A is selected as shown in
Figure 3. When the switch is ON, block B is mapped to the highest address as shown in Figure
4. The MAP_SELECT bit in the flash Control/Status register can disable the jumper and restore
the memory map to the normal configuration with block A selected.
70
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Flash Memory
Functional Description
4.8.1
Flash Memory
The MVME7100 is designed to provide 128 MB of soldered-on NOR flash memory. Two AMD
+3.3 V devices are configured to operate in 16-bit mode to form a 32-bit flash bank. This flash
bank is also the boot bank and is connected to LBC Chip Select 0 and 1.
Also included is a second bank of NAND flash, up to 32 GB, connected to LBC Chip Select 2.
The VPD flash packet(s) will determine which devices are populated and the size of the devices.
Programming details can be found in the MVME7100 Single Board Computer Programmer’s
Reference manual.
4.8.2
4.8.3
NVRAM
The MVME7100 includes one Freescale 512 MB MRAM device connected to the MC864xD
device control bus to provide a non-volatile memory that has unlimited writes, fast access and
long term data retention without power. The MRAM device selected is also an extended
temperature device with an operating range from -40°C to 105°C/-40°F to 221°F. The MRAM is
organized as 256 K by 16. Refer to the datasheet for additional information
Quad UART (QUART)
The MVME7100 contains one Quad UART device connected to the MC864xD device control
bus to provide additional asynchronous serial ports. The Quad UART provides four
asynchronous serial ports which are routed to the P2 connector. The TTL-level signals of RX,
TX, CTS, and RTS from each port are routed through on-board RS-232 drivers and receivers
to the P2 connector where the signals can be picked up by a transition module. The reference
clock frequency for the QUART is 1.8432 MHz. All UART ports are capable of signaling at up to
115 Kbaud. Refer to the ST16C554D datasheet for additional details and/or programming
information.
4.8.4
Control and Timers PLD
The MVME7100 Control and Timers PLD resides on the local bus. The Control and Timers PLD
provides the following functions on the board:
z
z
z
z
z
z
Local bus address latch
Chip selects for flash banks, MRAM, and Quad UART
System control and status registers
Four 32-bit tick timers
Watch Dog Timer
RTC 1 MHz reference clock
71
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Functional Description
DUART Interface
4.9 DUART Interface
The MVME7100 provides a front access asynchronous serial port interface using Serial Port 0
from the MC864xD DUART. The TTL-level signals SIN, SOUT, RTS and CTS from Serial Port
0 are routed through on-board RS-232 drivers and receivers to the mini DB-9 front panel
connector.
4.10 PCI-E Port 0
One 8x PCI-E port from the MC864xD processor is connected to a five port PEX8533 PCI-E
switch. Each downstream port from the PCI-E switch is connected to a PCI/PCI-X bridge. The
MVME7100 implements four separate PCI/PCI-X bus segments.
PCI-X bus 1 connects to PMC site 1 using a PEX8114 bridge and is configured dynamically,
with onboard logic, to operate in 33/66 MHz PCI or 66/100 MHz PCI-X mode depending on the
PMC installed.
PCI-X bus 2 connects to PMC site 2 using a PEX8114 bridge and is configured dynamically,
with onboard logic, to operate in 33/66 MHz PCI or 66/100 MHz PCI-X mode depending on the
PMC installed.
PCI-X bus 3 connects to the Tsi148 using a PEX8114 bridge and is configured for 133 MHz
PCI-X mode.
PCI bus 4 connects to the USB controller using a PEX8112 bridge and is configured for 33 MHz
PCI mode since the USB controller is only 33 MHz capable.
4.10.1 VME Controller
The VMEbus interface for the MVME7100 is provided by the Tsi148 VMEbus controller. The
Tsi148 provides the required VME, VME extensions, and 2eSST functions. TI
SN74VMEH22501 transceivers are used to buffer the VME signals between the Tsi148 and the
VME backplane. Refer to the Tsi148 user's manual for additional details and/or programming
information.
4.10.2 USB
The NEC uPD720101 USB 2.0 Host Controller provides USB ports with integrated transceivers
for connectivity with any USB compliant device or hub. USB channel 1 is routed to a single USB
connector located at the front panel. DC power to the front panel USB port is supplied via a USB
power switch which provides soft-start, current limiting, over current detection, and power
enable for port 1. Refer to the uPD720101 datasheet for additional details and/or programming
information.
72
MVME7100 Single Board Computer Installation and Use (6806800E08A)
XMC Expansion
Functional Description
4.11 XMC Expansion
The MVME7100 provides an additional XMC/PMC module capability through the use of a 78-
pin stacking connector. This connector is connected to the second PCI Express port on the
processor. Up to four additional XMC/PMC modules may be added by using two expansion
boards. Refer to the XMCspan datasheet for additional details and/or programming information.
4.12 Power Supplies
The MVME7100 on-board voltages will be generated using Linear Tech LTC3828 dual output
two phase controllers and LTC3416 single output controllers. The following sections detail the
MVME7100 power requirements.
4.12.1 Power Sequencing
In order to meet the power sequencing requirements of the various components on the
MVME7100, the power supply controllers implement voltage tracking which allows the power
supply outputs to track each other coincidentally during power up and power down. The +3.3 V
supply output will be used as the tracking reference. All supply outputs will reach their final
values within 20 milliseconds during power up.
4.12.2 Power Supply Monitor
Logic is provided on-board to monitor the PGOOD signal from the LTC3828 and LTC3416
regulators to determine if the power supply outputs are within tolerance. If any of the power
supplies fail, this logic shuts off the power supplies to avoid any component damage. If the +5.0
V power supply is still good during a fail condition, a planar red LED (PWR FAIL D9) is
illuminated to indicate the power supply fail condition.
4.12.3 Power Supply Filtering and Fusing
Each of the switching power supply inputs on the MVME7100 will have an inductor to reduce
switching noise from being fed back onto the +5.0 V input. The LTC3828 supplies will each have
a 10 A fuse to protect the supplies from over-current in case of component failure.
4.13 Clock Distribution
The clock function generates and distributes all of the clocks required for system operation. The
PCI-E clocks are generated using an eight output differential clock driver. The PCI/PCI-X bus
clocks are generated by the bridge chips from the PCI-E clock. Additional clocks required by
individual devices are generated near the devices using individual oscillators. For clock
assignments, refer to the MVME7100 Single Board Computer Programmer’s Reference
manual.
73
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Functional Description
System Clock
4.13.1 System Clock
The system clock is driven by an oscillator. The following table defines the clock frequencies for
various configurations.
Table 4-1 Clock Frequencies
SYSCLK
Core
MPX (Platform)
533 MHz
DDR2
66.67 MHz
66.67 MHz
1.3 GHz
1.067 GHz
266 MHz
266 MHz
533 MHz
4.13.2 Real Time Clock Input
The RTC clock input is driven by a 1 MHz clock generated by the Control and Timers PLD. This
provides a fixed clock reference for the MC864xD PIC timers which software can use as a
known timing reference.
4.13.3 Local Bus Controller Clock Divisor
The Local Bus Controller (LBC) clock output is connected to the PLD but is not used by the
internal logic
4.14 Reset Control Logic
There are multiple sources of reset on the MVME7100. The following sources generate a board
level reset:
z
z
z
z
z
Power-up
Reset switch
Watchdog timer
System control register (BRD_RST)
VMEbus reset
A board level hard reset generates a reset for the entire SBC including the processor, local
PCI/PCI-X buses, Ethernet PHYs, serial ports, flash devices, and PLD(s). If the MVME7100 is
configured as the VME system controller, the VMEbus and local Tsi148 reset input are also
reset.
4.15 Real Time Clock Battery
There is an on-board battery holder that provides easy replacement of a +3.0 V button cell
lithium battery (BR2325) which provides back-up power to the on-board Real Time Clock. A
battery switching circuit provides automatic switching between the +3.3 V and battery voltages.
74
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Transition Module
5
5.1 Overview
This chapter provides information on the MVME7216E transition module’s features. It also
includes a drawing of the module showing the components and rear panel connectors.
5.2 Transition Module Layout
The following illustration shows the component layout and connectors on the MVME7216E
transition module.
Figure 5-1 Component Layout
J1
J2
T2
T1
C25
C1
U1
L1
U4
C38
L2
C39
J10
S1 SMT Switch
C38
S1
U2
P2
J14
75
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Transition Module
Features
5.3 Features
The MVME7216E transition module is for I/O routing through the rear of a compact VMEbus
chassis. It connects directly to the VME backplane in chassis’ with an 80 mm deep rear
transition area. The MVME7216E is designed for use with the host MVME7100 board. It has
these features:
Table 5-1 Transition Module Features
Function
Features
I/O
One five-row P2 backplane connector for serial and Ethernet I/O passed from the SBC
Four RJ-45 connectors for rear panel I/O: four asynchronous serial channels
Two RJ-45 connectors with integrated LEDs for rear panel I/O: two 10/100/1000
Ethernet channels
One PIM site with rear panel I/O
Figure 5-2 Block Diagram
P2
Serial Port 1
Serial Port 2
Serial Port 3
Serial Port 4
I2C Bus
VPD
8 KB
GigE 1
PMC 1 Jn4 IO
GigE 2
PIM
GigE
RJ-45
Serial
RJ-45
GigE
Serial
Serial Serial
RJ-45 RJ-45
RJ-45 RJ-45
PIM IO
Rear Panel
5.4 SEEPROM Address Switch, S1
A 4-position SMT configuration switch is located on the MVME7216E transition module to set
the device address of the RTM serial EEPROM device. The switch settings are defined in the
next table. To see switch location, refer to Figure 5-1 on page 75.
Figure 5-3 S1 Switch Positions
ON
1
3
4
2
76
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Rear Panel Connectors
Transition Module
Table 5-2 SEEPROM Address Switch Assignments (RTM)
Position
SW4
WP
0
SW3
A(2)
1
SW2
A(1)
1
SW1
A(0)
1
Function
Default (OFF)
Table 5-3 Switch Settings and Device Addresses
SW4
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
SW3
ON
SW2
ON
SW1
ON
A(2:0)
Device Address
000
001
010
011
100
101
110
111
$A0
ON
ON
OFF
ON
$A2
ON
OFF
OFF
ON
$A4
ON
OFF
ON
$A6
OFF
OFF
OFF
OFF
$A8
ON
OFF
ON
$AA (default)
$AC
OFF
OFF
OFF
$AE
5.5 Rear Panel Connectors
The MVME7216E transition module provides these connectors. All connectors use standard
pin assignments in compliance with the VMEbus specifications.
Table 5-4 Transition Module Connectors
Connector
Function
J1A, J1B, J1C, J1D
COM port connectors
10/100/1000Mb/s Ethernet connector
10/100/1000Mb/s Ethernet connector
PIM power/ground
J2A
J2B
J10
J14
P2
PIM I/O
VME backplane connector
PMC I/O (PIM) connector J10 routes only power and ground from VME P2 connector. There
are no host I/O signals on this connector. The MVME7100 routes PMC I/O from J14 of PMC
Slot 1 to VME P2 rows A and C. The MVME7216E routes these signals (pin-for-pin) from VME
P2 to PMC I/O module connector J14.
77
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Transition Module
Rear Panel Connectors
Figure 5-4 Rear Panel Connectors and LEDs
COM2
COM3
COM4
COM5
ACT
G Enet 1
SPEED
ACT
G Enet 2
SPEED
PMC Site
There are two sets of ACT and SPEED LEDs, one set for each Ethernet connector. They are
described in the next table.
Table 5-5 Transition Module LEDs
LED
Function
ACT
Activity or Ethernet or Gigabit E Ethernet connector
10/100/1000Mb/s of Ethernet connectors
SPEED
78
MVME7100 Single Board Computer Installation and Use (6806800E08A)
PMC Input/Output Module
Transition Module
5.6 PMC Input/Output Module
If a PMC Input/output Module (PIM) has already been installed on the MVME7216E, or you are
installing a transition module as it has been shipped from the factory, disregard this procedure
and refer to Transition Module on page 40.
Procedure
For PIM installation, perform the following steps:
1. Attach an ESD strap to your wrist. Attach the other end of the ESD strap to the
chassis as a ground. The ESD strap must be secured to your wrist and to ground
throughout the procedure.
2. Carefully remove the transition module from its packaging and lay it flat on a stable
surface.
3. Remove the PIM filler from the front panel of the transition module.
4. Slide the face plate (front bezel) of the PIM module into the front panel opening from
behind and place the PIM module on top of the transition module, aligned with the
appropriate two PIM connectors. The two connectors on the underside of the PIM
module should then connect smoothly with the corresponding connectors on the
transition module (J10 and J14).
5. Insert the four short Phillips screws, provided with the PIM, through the holes on the
bottom side of the transition module into the PIM front bezel and rear standoffs.
Tighten the screws.
Refer to the following figure for proper screw/board alignment. The example below
may not accurately represent your MVME7100.
79
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Transition Module
PMC Input/Output Module
Figure 5-5 Installing the PIM
PIM Alignment
80
MVME7100 Single Board Computer Installation and Use (6806800E08A)
MOTLoad Firmware
6
6.1 Overview
The MOTLoad firmware package serves as a board power-up and initialization package, as well
as a vehicle from which user applications can be booted. A secondary function of the MOTLoad
firmware is to serve in some respects as a test suite providing individual tests for certain
devices. This chapter includes a list of standard MOTLoad commands, the default VME and
firmware settings that are changeable by the user, remote start, and the alternate boot
procedure.
MOTLoad is controlled through an easy-to-use, UNIX-like, command line interface. The
MOTLoad software package is similar to many end-user applications designed for the
embedded market, such as the real time operating systems currently available.
Refer to the MOTLoad Firmware Package User’s Manual, listed in Appendix B, Related
Documentation, for more details.
6.2 Implementation and Memory Requirements
The implementation of MOTLoad and its memory requirements are product specific. The
MVME7100 single-board computer (SBC) is offered with a range of memory (for example,
DRAM or flash). Typically, the smallest amount of on-board DRAM that a SBC has is 32 MB.
Each supported product line has its own unique MOTLoad binary image(s). Currently the
largest MOTLoad compressed image is less than 1 MB in size.
6.3 MOTLoad Commands
MOTLoad supports two types of commands (applications): utilities and tests. Both types of
commands are invoked from the MOTLoad command line in a similar fashion. Beyond that,
MOTLoad utilities and MOTLoad tests are distinctly different.
6.3.1
Utilities
The definition of a MOTLoad utility application is very broad. Simply stated, it is considered a
MOTLoad command if it is not a MOTLoad test. Typically, MOTLoad utility applications are
applications that aid the user in some way (that is, they do something useful). From the
perspective of MOTLoad, examples of utility applications are: configuration, data/status
displays, data manipulation, help routines, data/status monitors, etc.
81
MVME7100 Single Board Computer Installation and Use (6806800E08A)
MOTLoad Firmware
Tests
Operationally, MOTLoad utility applications differ from MOTLoad test applications in several
ways:
z
Only one utility application operates at any given time (that is, multiple utility applications
cannot be executing concurrently).
z
Utility applications may interact with the user. Most test applications do not.
6.3.2
Tests
A MOTLoad test application determines whether or not the hardware meets a given standard.
Test applications are validation tests. Validation is conformance to a specification. Most
MOTLoad tests are designed to directly validate the functionality of a specific SBC subsystem
or component. It is possible for a board's component to fail in the user application but pass
specification conformance. These tests validate the operation of such SBC modules as:
dynamic memory, external cache, NVRAM, real time clock, etc.
All MOTLoad tests are designed to validate functionality with minimum user interaction. Once
launched, most MOTLoad tests operate automatically without any user interaction. There are a
few tests where the functionality being validated requires user interaction (that is, switch tests,
interactive plug-in hardware modules, etc.). Most MOTLoad test results (error-data/status-data)
are logged, not printed. Test results are not preserved and therefore not available to user
applications subsequent to their execution. All MOTLoad tests/commands have complete and
separate descriptions (refer to the MOTLoad Firmware Package User’s Manual for this
information).
All devices that are available to MOTLoad for validation/verification testing are represented by
a unique device path string. Most MOTLoad tests require the operator to specify a test device
at the MOTLoad command line when invoking the test.
A listing of all device path strings can be displayed through the devShowcommand. If an SBC
device does not have a device path string, it is not supported by MOTLoad and can not be
directly tested. There are a few exceptions to the device path string requirement, like testing
RAM, which is not considered a true device and can be directly tested without a device path
string. Refer to the devShowcommand description page in the MOTLoad Firmware Package
User’s Manual.
Most MOTLoad tests can be organized to execute as a group of related tests (a testSuite)
through the use of the testSuitecommand. The expert operator can customize their testing
by defining and creating a custom testSuite(s). The list of built-in and user-defined MOTLoad
testSuites, and their test contents, can be obtained by entering testSuite -dat the
MOTLoad prompt. All testSuites that are included as part of a product specific MOTLoad
firmware package are product specific. For more information, refer to the testSuite
command description page in the MOTLoad Firmware Package User’s Manual.
Test results and test status are obtained through the testStatus, errorDisplay, and
taskActivecommands. Refer to the appropriate command description page in the MOTLoad
Firmware Package User’s Manual for more information.
82
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Command List
MOTLoad Firmware
6.3.3
Command List
The following table provides a list of all current MOTLoad commands. Products supported by
MOTLoad may or may not employ the full command set. Typing helpat the MOTLoad
command prompt will display all commands supported by MOTLoad for a given product.
Table 6-1 MOTLoad Commands
Command
Description
as
One-Line Instruction Assembler
Block Compare Byte/Halfword/Word
bcb
bch
bcw
bdTempShow
Display Current Board Temperature
Block Fill Byte/Halfword/Word
bfb
bfh
bfw
blkCp
blkFmt
blkRd
blkShow
blkVe
Block Copy
Block Format
Block Read
Block Show Device Configuration Data
Block Verify
blkWr
Block Write
bmb
bmh
bmw
Block Move Byte/Halfword/Word
br
Assign/Delete/Display User-Program Break-Points
Block Search Byte/Halfword/Word
bsb
bsh
bsw
bvb
bvh
bvw
Block Verify Byte/Halfword/Word
cdDir
cdGet
clear
cm
ISO9660 File System Directory Listing
ISO9660 File System File Load
Clear the Specified Status/History Table(s)
Turns on Concurrent Mode
csb
csh
csw
Calculates a Checksum Specified by Command-line Options
devShow
diskBoot
Display (Show) Device/Node Table
Disk Boot (Direct-Access Mass-Storage Device)
83
MVME7100 Single Board Computer Installation and Use (6806800E08A)
MOTLoad Firmware
Command List
Table 6-1 MOTLoad Commands (continued)
Command
Description
downLoad
ds
Down Load S-Record from Host
One-Line Instruction Disassembler
Echo a Line of Text
echo
elfLoader
errorDisplay
eval
ELF Object File Loader
Display the Contents of the Test Error Status Table
Evaluate Expression
execProgram
fatDir
Execute Program
FAT File System Directory Listing
FAT File System File Load
fatGet
fdShow
flashLock
flashProgram
flashShow
flashUnlock
gd
Display (Show) File Discriptor
Flash Memory Sector Lock
Flash Memory Program
Display Flash Memory Device Configuration Data
Flash Memory Sector Unlock
Go Execute User-Program Direct (Ignore Break-Points)
Global Environment Variable Delete
gevDelete
gevDump
gevEdit
gevInit
Global Environment Variable(s) Dump (NVRAM Header + Data)
Global Environment Variable Edit
Global Environment Variable Area Initialize (NVRAM Header)
Global Environment Variable Labels (Names) Listing
Global Environment Variable Show
gevList
gevShow
gn
Go Execute User-Program to Next Instruction
Go Execute User-Program
go
gt
Go Execute User-Program to Temporary Break-Point
Display History Buffer
hbd
hbx
Execute History Buffer Entry
help
Display Command/Test Help Strings
l2CacheShow
l3CacheShow
Display state of L2 Cache and L2CR register contents
Display state of L3 Cache and L3CR register contents
Memory Display Bytes/Halfwords/Words
mdb
mdh
mdw
memShow
Display Memory Allocation
mmb
mmh
mmw
Memory Modify Bytes/Halfwords/Words
84
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Command List
MOTLoad Firmware
Table 6-1 MOTLoad Commands (continued)
Command
Description
mpuFork
mpuShow
mpuStart
netBoot
netShow
netShut
netStats
noCm
Execute program from idle processor
Display multi-processor control structure
Start the other MPU
Network Boot (BOOT/TFTP)
Display Network Interface Configuration Data
Disable (Shutdown) Network Interface
Display Network Interface Statistics Data
Turns off Concurrent Mode
Read PCI Device Configuration Header Register
Write PCI Device Configuration Header Register
Dump PCI Device Configuration Header Register
Display PCI Device Configuration Header Register
Display PCI Device Address Space Allocation
Ping Network Host
pciDataRd
pciDataWr
pciDump
pciShow
pciSpace
ping
portSet
portShow
rd
Port Set
Display Port Device Configuration Data
User Program Register Display
Reset System
reset
rs
User Program Register Set
Set Date and Time
set
sromRead
sromWrite
sta
SROM Read
SROM Write
Symbol Table Attach
stl
Symbol Table Lookup
stop
Stop Date and Time (Power-Save Mode)
Display the Contents of the Active Task Table
Trace (Single-Step) User Program
Trace (Single-Step) User Program to Address
Test Disk
taskActive
tc
td
testDisk
testEnetPtP
testNvramRd
testNvramRdWr
testRam
testRamAddr
testRamAlt
testRamBitToggle
Ethernet Point-to-Point
NVRAM Read
NVRAM Read/Write (Destructive)
RAM Test (Directory)
RAM Addressing
RAM Alternating
RAM Bit Toggle
85
MVME7100 Single Board Computer Installation and Use (6806800E08A)
MOTLoad Firmware
Using the Command Line Interface
Table 6-1 MOTLoad Commands (continued)
Command
Description
testRamBounce
testRamCodeCopy
testRamEccMonitor
testRamMarch
testRamPatterns
testRamPerm
testRamQuick
testRamRandom
testRtcAlarm
testRtcReset
testRtcRollOver
testRtcTick
RAM Bounce
RAM Code Copy and Execute
Monitor for ECC Errors
RAM March
RAM Patterns
RAM Permutations
RAM Quick
RAM Random Data Patterns
RTC Alarm
RTC Reset
RTC Rollover
RTC Tick
testSerialExtLoop
testSeriallntLoop
testStatus
Serial External Loopback
Serial Internal Loopback
Display the Contents of the Test Status Table
Execute Test Suite
testSuite
testSuiteMake
testWatchdogTimer
tftpGet
Make (Create) Test Suite
Tests the Accuracy of the Watchdog Timer Device
TFTP Get
tftpPut
TFTP Put
time
Display Date and Time
transparentMode
tsShow
Transparent Mode (Connect to Host)
Display Task Status
upLoad
Up Load Binary Data from Target
Display Version String(s)
Manages user specified VME configuration parameters
VPD Display
version
vmeCfg
vpdDisplay
vpdEdit
VPD Edit
wait
Wait for Test Completion
Wait for I/O Probe to Complete
waitProbe
6.4 Using the Command Line Interface
Interaction with MOTLoad is performed via a command line interface through a serial port on
the single board computer, which is connected to a terminal or terminal emulator (for example,
Window’s Hypercomm). The default MOTLoad serial port settings are: 9600 baud, 8 bits, no
parity.
86
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Using the Command Line Interface
MOTLoad Firmware
The MOTLoad command line interface is similar to a UNIX command line shell interface.
Commands are initiated by entering a valid MOTLoad command (a text string) at the MOTLoad
command line prompt and pressing the carriage-return key to signify the end of input. MOTLoad
then performs the specified action. An example of a MOTLoad command line prompt is shown
below. The MOTLoad prompt changes according to what product it is used on (for example,
MVME6100, MVME3100, MVME7100).
Example:
MVME7100>
If an invalid MOTLoad command is entered at the MOTLoad command line prompt, MOTLoad
displays a message that the command was not found.
Example:
MVME7100> mytest
"mytest" not found
MVME7100>
If the user enters a partial MOTLoad command string that can be resolved to a unique valid
MOTLoad command and presses the carriage-return key, the command is executed as if the
entire command string had been entered. This feature is a user-input shortcut that minimizes
the required amount of command line input. MOTLoad is an ever changing firmware package,
so user-input shortcuts may change as command additions are made.
Example:
MVME7100>[ver]sion
Copyright: Motorola Inc.1999-2005, All Rights Reserved
MOTLoad RTOS Version 2.0, PAL Version 1.0 RM01
Mon Aug 29 15:24:13 MST 2005
MVME7100>
Example:
MVME7100> ver
Copyright: Motorola Inc.1999-2005, All Rights Reserved
MOTLoad RTOS Version 2.0, PAL Version 1.0 RM01
Mon Aug 29 15:24:13 MST 2005
MVME7100>
If the partial command string cannot be resolved to a single unique command, MOTLoad
informs the user that the command was ambiguous.
Example:
MVME7100> te
"te" ambiguous
MVME7100>
87
MVME7100 Single Board Computer Installation and Use (6806800E08A)
MOTLoad Firmware
Rules
6.4.1
Rules
There are a few things to remember when entering a MOTLoad command:
z
Multiple commands are permitted on a single command line, provided they are separated
by a single semicolon (;).
z
z
z
z
z
Spaces separate the various fields on the command line (command/arguments/options).
The argument/option identifier character is always preceded by a hyphen (-) character.
Options are identified by a single character.
Option arguments immediately follow (no spaces) the option.
All commands, command options, and device tree strings are case sensitive.
Example:
MVME7100> flashProgram –d/dev/flash0 –n00100000
For more information on MOTLoad operation and function, refer to the MOTLoad Firmware
Package User’s Manual.
6.4.2
Help
Each MOTLoad firmware package has an extensive, product-specific help facility that can be
accessed through the helpcommand. The user can enter helpat the MOTLoad command
line to display a complete listing of all available tests and utilities.
Example
MVME7100> help
For help with a specific test or utility the user can enter the following at the MOTLoad prompt:
help <command_name>
The helpcommand also supports a limited form of pattern matching. Refer to the help
command page.
Example
MVME7100> help testRam
Usage: testRam [-aPh] [-bPh] [-iPd] [-nPh] [-tPd] [-v]
Description: RAM Test [Directory]
Argument/Option Description
-a Ph: Address to Start (Default = Dynamic Allocation)
-b Ph: Block Size (Default = 16KB)
-i Pd: Iterations (Default = 1)
-n Ph: Number of Bytes (Default = 1MB)
-t Ph: Time Delay Between Blocks in OS Ticks (Default = 1)
-v O : Verbose Output
MVME7100>
88
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Firmware Settings
MOTLoad Firmware
6.5 Firmware Settings
The following sections provide additional information pertaining to the MVME7100 VME bus
interface settings as configured by MOTLoad. A few VME settings are controlled by hardware
jumpers while the majority of the VME settings are managed by the firmware command utility
vmeCfg.
VME settings in MOTLoad are preserved through the use of Global Environment
Variables (GEVs). Configuration GEVs are executed only at power-on reset. Therefore,
if VME configuration changes are implemented through vmeCfg and board reset must
be effected for the changes to be implemented in MOTLoad.
6.5.1
Default VME Settings
As shipped from the factory, the MVME7100 has the following VME configuration programmed
via Global Environment Variables (GEVs) for the Tsi148 VME controller. The firmware allows
certain VME settings to be changed in order for the user to customize the environment. The
following is a description of the default VME settings that are changeable by the user. For more
information, refer to the MOTLoad User’s Manual and Tundra’s Tsi148 User Manual, listed in
Appendix B, Related Documentation.
z MVME7100> vmeCfg -s -m
Displaying the selected Default VME Setting
- interpreted as follows:
VME PCI Master Enable [Y/N] = Y
MVME7100>
The PCI Master is enabled.
z MVME7100> vmeCfg -s -r234
Displaying the selected Default VME Setting
- interpreted as follows:
VMEbus Master Control Register = 00000003
MVME7100>
The VMEbus Master Control Register is set to the default (RESET) condition.
z MVME7100> vmeCfg -s -r238
Displaying the selected Default VME Setting
- interpreted as follows:
VMEbus Control Register = 00000008
MVME7100>
The VMEbus Control Register is set to a Global Timeout of 2048 μseconds.
z MVME7100> vmeCfg -s -r414
89
MVME7100 Single Board Computer Installation and Use (6806800E08A)
MOTLoad Firmware
Default VME Settings
Displaying the selected Default VME Setting
- interpreted as follows:
CRG Attribute Register = 00000000
CRG Base Address Upper Register = 00000000
CRG Base Address Lower Register = 00000000
MVME7100>
The CRG Attribute Register is set to the default (RESET) condition.
z MVME7100> vmeCfg –s –i0
Displaying the selected Default VME Setting
- interpreted as follows:
Inbound Image 0 Attribute Register = 000227AF
Inbound Image 0 Starting Address Upper Register = 00000000
Inbound Image 0 Starting Address Lower Register = 00000000
Inbound Image 0 Ending Address Upper Register = 00000000
Inbound Image 0 Ending Address Lower Register = 1FFF0000
Inbound Image 0 Translation Offset Upper Register = 00000000
Inbound Image 0 Translation Offset Lower Register = 00000000
MVME7100>
Inbound window 0 (ITAT0) is not enabled; Virtual FIFO at 256 bytes, 2eSST timing at
SST320, respond to 2eSST, 2eVME, MBLT, and BLT cycles, A32 address space, respond
to Supervisor, User, Program, and Data cycles. Image maps from 0x00000000 to
0x1FFF0000 on the VMEbus, translates 1x1 to the PCI-X bus (thus 1x1 to local memory).
To enable this window, set bit 31 of ITAT0 to 1.
z MVME7100> vmeCfg –s –o1
Displaying the selected Default VME Setting
- interpreted as follows:
Outbound Image 1 Attribute Register = 80001462
Outbound Image 1 Starting Address Upper Register = 00000000
Outbound Image 1 Starting Address Lower Register = 91000000
Outbound Image 1 Ending Address Upper Register = 00000000
Outbound Image 1 Ending Address Lower Register = AFFF0000
Outbound Image 1 Translation Offset Upper Register = 00000000
Outbound Image 1 Translation Offset Lower Register = 70000000
Outbound Image 1 2eSST Broadcast Select Register = 00000000
MVME7100>
Outbound window 1 (OTAT1) is enabled, 2eSST timing at SST320, transfer mode of 2eSST,
A32/D32 Supervisory access. The window accepts transfers on the PCI-X Local Bus from
0x91000000-0xAFFF0000 and translates them onto the VMEbus using an offset of
0x70000000, thus an access to 0x91000000 on the PCI-X Local Bus becomes an access
to 0x01000000 on the VMEbus.
z MVME7100> vmeCfg –s –o2
Displaying the selected Default VME Setting
- interpreted as follows:
Outbound Image 2 Attribute Register = 80001061
Outbound Image 2 Starting Address Upper Register = 00000000
Outbound Image 2 Starting Address Lower Register = B0000000
Outbound Image 2 Ending Address Upper Register = 00000000
Outbound Image 2 Ending Address Lower Register = B0FF0000
90
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Default VME Settings
MOTLoad Firmware
Outbound Image 2 Translation Offset Upper Register = 00000000
Outbound Image 2 Translation Offset Lower Register = 40000000
Outbound Image 2 2eSST Broadcast Select Register = 00000000
MVME7100>
Outbound window 2 (OTAT2) is enabled, 2eSST timing at SST320, transfer mode of SCT,
A24/D32 Supervisory access. The window accepts transfers on the PCI-X Local Bus from
0xB0000000-0xB0FF0000 and translates them onto the VMEbus using an offset of
0x40000000, thus an access to 0xB0000000 on the PCI-X Local Bus becomes an access
to 0xF0000000 on the VMEbus.
z MVME7100> vmeCfg –s –o3
Displaying the selected Default VME Setting
- interpreted as follows:
Outbound Image 3 Attribute Register = 80001061
Outbound Image 3 Starting Address Upper Register = 00000000
Outbound Image 3 Starting Address Lower Register = B3FF0000
Outbound Image 3 Ending Address Upper Register = 00000000
Outbound Image 3 Ending Address Lower Register = B3FF0000
Outbound Image 3 Translation Offset Upper Register = 00000000
Outbound Image 3 Translation Offset Lower Register = 4C000000
Outbound Image 3 2eSST Broadcast Select Register = 00000000
MVME7100>
Outbound window 3 (OTAT3) is enabled, 2eSST timing at SST320, transfer mode of SCT,
A16/D32 Supervisory access. The window accepts transfers on the PCI-X Local Bus from
0xB3FF0000-0xB3FF0000 and translates them onto the VMEbus using an offset of
0x4C000000, thus an access to 0xB3FF0000 on the PCI-X Local Bus becomes an access
to 0xFFFF0000 on the VMEbus.
z MVME7100> vmeCfg –s –o7
Displaying the selected Default VME Setting
- interpreted as follows:
Outbound Image 7 Attribute Register = 80001065
Outbound Image 7 Starting Address Upper Register = 00000000
Outbound Image 7 Starting Address Lower Register = B1000000
Outbound Image 7 Ending Address Upper Register = 00000000
Outbound Image 7 Ending Address Lower Register = B1FF0000
Outbound Image 7 Translation Offset Upper Register = 00000000
Outbound Image 7 Translation Offset Lower Register = 4F000000
Outbound Image 7 2eSST Broadcast Select Register = 00000000
MVME7100>
Outbound window 7 (OTAT7) is enabled, 2eSST timing at SST320, transfer mode of SCT,
CR/CSR Supervisory access. The window accepts transfers on the PCI-X Local Bus from
0xB1000000-0xB1FF0000 and translates them onto the VMEbus using an offset of
0x4F000000, thus an access to 0xB1000000 on the PCI-X Local Bus becomes an access
to 0x00000000 on the VMEbus.
91
MVME7100 Single Board Computer Installation and Use (6806800E08A)
MOTLoad Firmware
Control Register/Control Status Register Settings
6.5.2
Control Register/Control Status Register Settings
The CR/CSR base address is initialized to the appropriate setting based on the Geographical
address; that is, the VME slot number. See the VME64 Specification and the VME64
Extensions for details. As a result, a 512 KB CR/CSR area can be accessed from the VMEbus
using the CR/CSR AM code.
6.5.3
Displaying VME Settings
To display the changeable VME setting, type the following at the firmware prompt:
z
z
z
z
z
z
To display Master Enable state:
vmeCfg –s –m
To display selected Inbound Window state:
vmeCfg –s –i(0 - 7)
To display selected Outbound Window state:
vmeCfg –s –o(0 - 7)
To display Master Control Register state:
vmeCfg –s –r234
To display Miscellaneous Control Register state:
vmeCfg –s –r238
To display CRG Attribute Register state:
vmeCfg –s –r414
6.5.4
Editing VME Settings
To edit the changeable VME setting, type the following at the firmware prompt:
z
z
z
z
z
z
Edits Master Enable state:
vmeCfg –e –m
Edits selected Inbound Window state:
vmeCfg –e –i(0 - 7)
Edits selected Outbound Window state:
vmeCfg –e –o(0 - 7)
Edits Master Control Register state:
vmeCfg –e –r234
Edits Control Register state:
vmeCfg –e –r238
Edits CRG Attribute Register state:
vmeCfg –e –r414
92
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Deleting VME Settings
MOTLoad Firmware
6.5.5
Deleting VME Settings
To delete the changeable VME setting (restore default value), type the following at the firmware
prompt:
z
z
z
z
z
z
Deletes Master Enable state:
vmeCfg –d –m
Deletes selected Inbound Window state:
vmeCfg –d –i(0 - 7)
Deletes selected Outbound Window state:
vmeCfg –d –o(0 - 7)
Deletes Master Control Register state:
vmeCfg –d –r234
Deletes Control Register state:
vmeCfg –d –r238
Deletes CRG Attribute Register state:
vmeCfg –d –r414
6.5.6
Restoring Default VME Settings
To restore all of the changeable VME setting back to their default settings, type the following at
the firmware prompt:
vmeCfg –z
6.6 Remote Start
As described in the MOTLoad Firmware Package User's Manual, listed in Appendix B, Related
Documentation, remote start allows the user to obtain information about the target board,
download code and/or data, modify memory on the target, and execute a downloaded program.
These transactions occur across the VMEbus in the case of the MVME7100. MOTLoad uses
one of four mailboxes in the Tsi148 VME controller as the inter-board communication address
(IBCA) between the host and the target.
CR/CSR slave addresses configured by MOTLoad are assigned according to the installation
slot in the backplane, as indicated by the VME64 Specification. For reference, the following
values are provided:
CS/CSR Starting Address
Slot Position
0x0008.0000
0x0010.0000
0x0018.0000
0x0020.0000
0x0028.0000
0x0030.0000
1
2
3
4
5
6
93
MVME7100 Single Board Computer Installation and Use (6806800E08A)
MOTLoad Firmware
Boot Images
CS/CSR Starting Address
Slot Position
0x0038.0000
0x0040.0000
0x0048.0000
0x0050.0000
0x0058.0000
0x0060.0000
7
8
9
A
B
C
For further details on CR/CSR space, please refer to the VME64 Specification, listed in
Appendix B, Related Documentation.
The MVME7100 uses a TSi148 for its PCI/X-to-VME bus bridge. The offsets of the mailboxes
in the TSi148 are defined in the TSi148 VMEBus PCI/X-to-VME User Manual, listed in
Appendix B, Related Documentation, but are noted here for reference:
Mailbox 0 is at offset 7f610 in the CR/CSR space
Mailbox 1 is at offset 7f614 in the CR/CSR space
Mailbox 2 is at offset 7f618 in the CR/CSR space
Mailbox 3 is at offset 7f61C in the CR/CSR space
The selection of the mailbox used by remote start on an individual MVME7100 is determined
by the setting of a global environment variable (GEV). The default mailbox is zero. Another GEV
controls whether remote start is enabled (default) or disabled. Refer to the Remote Start
appendix in the MOTLoad Firmware Package User's Manual for remote start GEV definitions.
The MVME7100’s IBCA needs to be mapped appropriately through the master’s VMEbus
bridge. For example, to use remote start using mailbox 0 on an MVME7100 installed in slot 5,
the master would need a mapping to support reads and writes of address 0x002ff610 in VME
CR/CSR space (0x280000 + 0x7f610).
6.7 Boot Images
Valid boot images whether POST, USER, or Alternate MOTLoad, are located on 1 MB
boundaries within the upper 8 MB of flash. The image may exceed 1 MB in size. An image is
determined valid through the presence of two "valid image keys" and other sanity checks. A
valid boot image begins with a structure as defined in the following table:
Name
Type
Size
8
Notes
UserDefined
ImageKey 1
ImageKey 2
ImageChecksum
ImageSize
unsigned integer
unsigned integer
unsigned integer
unsigned integer
unsigned integer
unsigned character
unsigned integer
User defined
0x414c5420
1
1
0x424f4f54
1
Image checksum
Must be a multiple of 4
User defined
RAM address
1
ImageName
ImageRamAddress
20
1
94
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Checksum Algorithm
Name
MOTLoad Firmware
Type
Size
Notes
ImageOffset
unsigned integer
unsigned integer
unsigned integer
unsigned integer
1
1
1
8
Offset from header start to entry
Refer to Image Flags on page 95
User defined
ImageFlags
ImageVersion
Reserved
Reserved for expansion
6.7.1
Checksum Algorithm
The checksum algorithm is a simple unsigned word add of each word (4 byte) location in the
image. The image must be a multiple of 4 bytes in length (word-aligned). The content of the
checksum location in the header is not part of the checksum calculation. The calculation
assumes the location to be zero. The algorithm is implemented using the following code:
Unsigned int checksum(
Unsigned int *startPtr,/* starting address */
Unsigned int endPtr/* ending address */
) {
unsigned int checksum=0;
while (startPtr < endPtr) {
checksum += *startPtr;
startPtr++;
}
return(checksum);
}
6.7.2
Image Flags
The image flags of the header define various bit options that control how the image will be
executed.
Table 6-2 MOTLoad Image Flags
Name
Value
Interpretation
COPY_TO_RAM
IMAGE_MCG
IMAGE_POST
DONT_AUTO_RUN
0x00000001
0x00000002
0x00000004
0x00000008
Copy image to RAM at ImageRamAddressbefore execution
Alternate MOTLoad image
POST image
Image not to be executed
z
COPY_TO_RAM
If set, this flag indicates that the image is to be copied to RAM at the address specified in
the header before control is passed. If not set, the image will be executed in flash. In both
instances, control will be passed at the image offset specified in the header from the base
of the image.
z
IMAGE_MCG
If set, this flag defines the image as being an Alternate MOTLoad, as opposed to USER,
image. This bit should not be set by developers of alternate boot images.
95
MVME7100 Single Board Computer Installation and Use (6806800E08A)
MOTLoad Firmware
User Images
z
IMAGE_POST
If set, this flag defines the image as being a power-on self-test image. This bit flag is used
to indicate that the image is a diagnostic and should be run prior to running either USER or
MCG boot images. POST images are expected, but not required, to return to the boot block
code upon completion.
z
DONT_AUTO_RUN
If set, this flag indicates that the image is not to be selected for automatic execution. A user,
through the interactive command facility, may specify the image to be executed.
MOTLoad currently uses an Image Flag value of 0x3, which identifies itself as an
Alternate MOTLoad image that executes from RAM. MOTLoad currently does not
support execution from flash.
6.7.3
User Images
These images are user-developer boot code; for example, a VxWorks bootrom image. Such
images may expect the system software state to be as follows upon entry:
z
z
z
z
z
z
z
z
z
The MMU is disabled.
L1 instruction cache has been initialized and is enabled.
L1 data cache has been initialized (invalidated) and is disabled.
L2 cache is disabled.
L3 cache is disabled.
RAM has been initialized and is mapped starting at CPU address 0.
If RAM ECC or parity is supported, RAM has been scrubbed of ECC or parity errors.
The active flash bank (boot) is mapped from the upper end of the address space.
If specified by COPY_TO_RAM, the image has been copied to RAM at the address
specified by ImageRamAddress.
z
z
CPU register R1 (the stack pointer) has been initialized to a value near the end of RAM.
CPU register R3 is added to the following structure:
typedef struct altBootData {
unsigned int ramSize;/* board's RAM size in MB */
void flashPtr;/* ptr to this image in flash */
char boardType[16];/* name string, eg MVME7100 */
void globalData;/* 16K, zeroed, user defined */
unsigned int reserved[12];
} altBootData_t;
96
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Alternate Boot Data Structure
MOTLoad Firmware
6.7.4
Alternate Boot Data Structure
The globalData field of the alternate boot data structure points to an area of RAM which was
initialized to zeroes by the boot loader. This area of RAM is not cleared by the boot loader after
execution of a POST image, or other alternate boot image, is executed. It is intended to provide
a user a mechanism to pass POST image results to subsequent boot images.
The boot loader performs no other initialization of the board than that specified prior to the
transfer of control to either a POST, USER, or Alternate MOTLoad image. Alternate boot
images need to initialize the board to whatever state the image may further require for its
execution.
POST images are expected, but not required, to return to the boot loader. Upon return, the boot
loader proceeds with the scan for an executable alternate boot image. POST images that return
control to the boot loader must ensure that upon return, the state of the board is consistent with
the state that the board was in at POST entry. USER images should not return control to the
boot loader.
6.7.5
6.7.6
Alternate Boot Images and Safe Start
Some later versions of MOTLoad support alternate boot images and a safe start recovery
procedure. If safe start is available on the MVME7100, alternate boot images are supported.
With alternate boot image support, the boot loader code in the boot block examines the upper
8 MB of the flash bank for alternate boot images. If an image is found, control is passed to the
image.
Boot Image Firmware Scan
The scan is performed by examining each 1 MB boundary for a defined set of flags that identify
the image as being POST, USER, or Alternate MOTLoad. POST is a user-developed Power On
Self Test that would perform a set of diagnostics and then return to the boot loader image.
USER would be a boot image, such as the VxWorks bootrom, which would perform board
initialization. A bootable VxWorks kernel would also be a USER image. Boot images are not
restricted to being 1 MB or less in size; however, they must begin on a 1 MB boundary within
the 8 MB of the scanned flash bank. The flash bank structure is shown below:
Address
Usage
0xFFF00000 to 0xFFFFFFFF
0xFFE00000 to 0XFFFFFFFF
0xFFD00000 to 0xFFDFFFFF
0xFFC00000 to 0xFFCFFFFF
....
Boot block. Recovery code.
Backup MOTLoad image
First possible alternate image
Second possible alternate image
Alternate boot images
0xFF899999 to 0xFF8FFFFF
Bottom of flash (flash size varies per product)
The scan is performed downwards beginning at the location of the first possible alternate image
and searches first for POST, then USER, and finally Alternate MOTLoad images. In the case of
multiple images of the same type, control is passed to the first image encountered in the scan.
97
MVME7100 Single Board Computer Installation and Use (6806800E08A)
MOTLoad Firmware
Startup Sequence
Safe Start, whether invoked by hitting ESC on the console within the first five seconds following
power-on reset or by setting the Safe Start jumper, interrupts the scan process. The user may
then display the available boot images and select the desired image. The feature is provided to
enable recovery in cases when the programmed Alternate Boot Image is no longer desired. The
following output is an example of an interactive Safe Start:
ABCDEInteractive Boot Mode Entered
boot> ?
Interactive boot commands:
'd':show directory of alternate boot images
'c':continue with normal startup
'q':quit without executing any alternate boot image
'r [address]':execute specified (or default) alternate image
'p [address]':execute specified (or default) POST image
'?':this help screen
'h':this help screen
boot> d
Addr FFE00000 Size 00100000 Flags 00000003 Name: MOTLoad
Addr FFD00000 Size 00100000 Flags 00000003 Name: MOTLoad
boot> c
NOPQRSTUVabcdefghijk#lmn3opqrsstuvxyzaWXZ
Copyright Motorola Inc. 1999-2004, All Rights Reserved
MOTLoad RTOS Version 2.0, PAL Version 0.b EA02
...
MVME7100>
6.8 Startup Sequence
The firmware startup sequence following reset of MOTLoad is to:
z
z
z
Initialize cache, MMU, FPU, and other CPU internal items
Initialize the memory controller
Search the active flash bank, possibly interactively, for a valid Power On Self Test (POST)
image. If found, the POST images executes. Once completed, the POST image returns and
startup continues.
z
z
Search the active flash bank, possibly interactively, for a valid USER boot image. If found,
the USER boot image executes. A return to the boot block code is not anticipated.
If a valid USER boot image is not found, search the active flash bank, possibly interactively,
for a valid Alternate MOTLoad boot image; anticipated to be an upgrade of alternate
MOTLoad firmware. If found, the image is executed. A return to the boot block code is not
anticipated.
z
Execute the recovery image of the firmware in the boot block if no valid USER or alternate
MOTLoad image is found
During startup, interactive mode may be entered by either setting the Safe Start jumper/switch
or by sending an <ESC>to the console serial port within five seconds of the board reset. During
interactive mode, the user has the option to display locations at which valid boot images were
discovered, specify which discovered image is to be executed, or specify that the recovery
image in the boot block of the active flash bank is to be executed.
98
MVME7100 Single Board Computer Installation and Use (6806800E08A)
A
Battery Exchange
A
A.1 Battery Exchange
Some blade variants contain an on-board battery. The battery location is shown in the following
figure.
Figure A-1 Battery Location
Battery
99
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Battery Exchange
Battery Exchange
The battery provides data retention of seven years summing up all periods of actual data use.
Emerson therefore assumes that there usually is no need to exchange the battery except, for
example, in case of long-term spare part handling.
Board/System Damage
Incorrect exchange of lithium batteries can result in a hazardous explosion.
When exchanging the on-board lithium battery, make sure that the new and the old
battery are exactly the same battery models.
If the respective battery model is not available, contact your local Emerson sales
representative for the availability of alternative, officially approved battery models.
Data Loss
Exchanging the battery can result in loss of time settings. Backup power prevents the
loss of data during exchange.
Quickly replacing the battery may save time settings.
Data Loss
If the battery has low or insufficient power the RTC is initialized.
Exchange the battery before seven years of actual battery use have elapsed.
PCB and Battery Holder Damage
Removing the battery with a screw driver may damage the PCB or the battery holder.
To prevent damage, do not use a screw driver to remove the battery from its holder.
Exchange Procedure
To exchange the battery, proceed as follows:
1. Remove the old battery.
2. Install the new battery with the plus sign (+) facing up.
3. Dispose of the old battery according to your country’s legislation and in an
environmentally safe way.
100
MVME7100 Single Board Computer Installation and Use (6806800E08A)
B
Related Documentation
B
B.1 Emerson Network Power - Embedded Computing
Documents
The Emerson Network Power - Embedded Computing publications listed below are referenced
in this manual. You can obtain electronic copies of Emerson Network Power - Embedded
Computing publications by contacting your local Emerson sales office. For documentation of
final released (GA) products, you can also visit the following website:
www.emersonnetworkpower.com/embeddedcomputing > Solution Services > Technical
Documentation Search. This site provides the most up-to-date copies of Emerson Network
Power - Embedded Computing product documentation.
Table B-1 Emerson Network Power - Embedded Computing Publications
Document Title
Publication Number
6806800E82
MVME7100 Single Board Computer Programmer’s Reference
MOTLoad Firmware Package User’s Manual
XMCspan Installlation and Use
6806800C24
6806800H03
B.2 Manufacturers’ Documents
For additional information, refer to the following table for manufacturers’ data sheets or user’s
manuals. As an additional help, a source for the listed document is provided. Please note that,
while these sources have been verified, the information is subject to change without notice.
Table B-2 Manufacturer’s Publications
Document Title and Source
Publication Number
AMD
Data Sheet
Revision A Amendment 4
May 13, 2004
S29GLxxxN MirrorBitTM Flash Family
S29GL512N, S29GL256N, S29GL128N
512 Megabit, 256 Megabit, and 128 Megabit, 3.0 Volt-only Page Mode
Flash Memory featuring 110 nm MirrorBit process technology
Atmel Corporation
2-Wire Serial EEPROM
32K (4096 x 8), 64K (8192 x 8)
AT24C32C, AT24C64C
5174B-SEEPR-12/06
101
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Related Documentation
Manufacturers’ Documents
Table B-2 Manufacturer’s Publications (continued)
Document Title and Source
Publication Number
2-Wire Serial EEPROM
512K (65,536 x 8)
AT24C512
Rev. 1116K-SEEPR-1/04
NEC Corporation
Data Sheet
S16265EJ3V0DS00
April 2003
µPD720101
USB2.0 Host Controller
Freescale Corporation
MC864xD Integrated Host Processor Reference Manual
MC864xD Errata
MC864xD Integrated Processor Hardware Specifications
Freescale 512 MB MRAM
Texas Instruments
Data Sheet
SCES357E
SN74VMEH22501
Revised March 2004
8-bit Universal Bus Transceiver and Two 1-bit Bus Transceivers with
Split LVTTL Port, Feedback Path, and 3-state Outputs
Exar
ST16C554/554D, ST68C554
Version 4.0.1
June 2006
Quad UART with 16-Byte FIFO's
Maxim Integrated Products
DS1375 Serial Real-Time Clock
REV: 121203
MAX3221E/MAX3223E/MAX3243E ±15kV ESD-Protected, 1µA, 3.0V 19-1283
to 5.5V, 250kbps,
Rev 5
RS-232 Transceivers with AutoShutdown
10/03
MAX811/MAX812
19-0411
Rev 3
3/99
4-Pin µP Voltage Monitors
With Manual Reset Input
MAX6649 Digital Temperature Sensor
19-2450
Rev 3
05/07
Tundra Semiconductor Corporation
Tsi148 PCI/X-to-VME Bus Bridge User Manual
FN 80A3020
MA001_08
102
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Related Specifications
Related Documentation
Table B-2 Manufacturer’s Publications (continued)
Document Title and Source
Publication Number
Broadcom Corporation
BCM5482S
5482S-DS06-R
2/15/07
10/100/1000BASE-T Gigabit Ethernet Transceiver
PLX Technology
PEX8112AA
Version 1.2
Version 3.0
Version 0.95
ExpressLane PCI Express-to-PCI Bridge
Data Book
ExpressLane PEX 8114BC
PCI Express-to-PCI/PCI-X Bridge
Data Book
ExpressLane PEX 8525AA
5-Port/24-Lane Versatile
PCI Express Switch
Data Book
B.3 Related Specifications
For additional information, refer to the following table for related specifications. As an additional
help, a source for the listed document is provided. Please note that, while these sources have
been verified, the information is subject to change without notice.
Table B-3 Related Specifications
Organization and Standard
VITA Standards Organization
VME64
Document Title
ANSI/VITA 1-1994
ANSI/VITA 1.1-1997
ANSI/VITA 1.5-2003
ANSI/VITA 32-2003
ANSI/VITA 39-2003
VME64 Extensions
2eSST Source Synchronous Transfer
Processor PMC
PCI-X for PMC and Processor PMC
PMC I/O Module (PIM) Draft Standard
VITA 36
Draft Rev 0.1
July 19, 1999
Universal Serial Bus
Universal Serial Bus Specification
Revision 2.0
April 27, 2000
PCI Special Interest Group
PCI Local Bus Specification, Revision 2.2
PCI Rev 2.2
December 18, 1998
103
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Related Documentation
Related Specifications
Document Title
Table B-3 Related Specifications (continued)
Organization and Standard
PCI-X Electrical and Mechanical Addendum to the PCI Local Bus
Specification, Revision 2.0a
PCI-X EM 2.0a
August 22, 2003
PCI-X Protocol Addendum to the PCI Local Bus Specification, Revision
2.0a
PCI-X PT 2.0a
July 22, 2003
Institute for Electrical and Electronics Engineers, Inc.
Draft Standard for a Common Mezzanine Card Family: CMC
P1386 - 2001
P1386 - 2001
Draft Standard Physical and Environmental Layer for PCI Mezzanine
Cards: PMC
104
MVME7100 Single Board Computer Installation and Use (6806800E08A)
Index
A
H
alternate boot images 97
help command
MOTLoad 88
B
I
battery exchange 100
board initialization 97
boot code 96
inspecting shipment 30
installation, completing 45
boot images, types 94
bootloader 97
L
Linux 45
C
list of commands
MOTLoad 83
lithium battery, 100
checksum 95
command line rules
MOTLoad 88
M
MOTLoad
command line rules and help 86
completing the installation 45
compliances 27
alternate boot data structure 97
command characteristics 87
command line help 88
command line interface 86
command line rules 88
command types 81
command versus test 81
commands 83
control register 93
control status register 93
D
damage reporting 30
default VME settings 89
delete 93
display 92
described 81
edit 92
restore 93
how employed 81
image flags 95
delete VME settings 93
display VME settings 92
disposal of product 27, 30
interface 86
memory requirements 81
prompt explained 87
requirements 81
test applications 82
test suites 82
tests described 82
user images 96
utilities 81
E
edit VME settings 92
EMC requirements 27
environment customization 89
environmental requirements 27, 30
F
O
firmware bootloader 97
firmware command utility 89
firmware package help 86
firmware scan 97
on-board battery 100
ordering product 28
P
firmware startup sequence 98
firmware tests 82
PIM installation 79
PMC 29, 41
firmware utilities 81
firmware, safe start 97
power requirements 30
product, how to order 28
G
R
global environment variables 89
remote start 93
replacing the battery 100
restoring VME settings 93
105
MVME7100 Single Board Computer Installation and Use (6806800E08A)
S
V
settings, VME 89
specifications
board 31
VME configuration 89
VME settings 89, 93
delete 93
standard compliancy 27
startup overview 29
display 92
edit 92
restore 93
vmeCfg 89
T
thermal requirements 30
transition module
PIM installation 79
X
XMCspan 29, 43
U
user images 97
106
MVME7100 Single Board Computer Installation and Use (6806800E08A)
|