Elo Touchmonitor
User Guide
For 15” LCD Desktop
1522L-XXWB Series
Revision A
Copyright © 2007 Tyco Electronics Corporation. All Rights Reserved.
No part of this publication may be reproduced, transmitted, transcribed, stored in a
retrieval system, or translated into any language or computer language, in any form or by
any means, including, but not limited to, electronic, magnetic, optical, chemical, manual,
or otherwise without prior written permission of Tyco Electronics.
Disclaimer
The information in this document is subject to change without notice. Tyco Electronics
makes no representations or warranties with respect to the contents hereof, and
specifically disclaims any implied warranties of merchantability or fitness for a
particular purpose. Tyco Electronics reserves the right to revise this publication and to
make changes from time to time in the content hereof without obligation of Tyco
Electronics to notify any person of such revisions or changes.
Trademark Acknowledgments
Elo TouchSystems, IntelliTouch, SecureTouch, AccuTouch, and MonitorMouse are
trademarks of Tyco Electronics Corporation.
Other product names mentioned herein may be trademarks or registered trademarks of
their respective companies. Tyco Electronics claims no interest in trademarks other than
its own.
Table of Contents
Controls and Adjustment .............................. 23
Chapter 1
OSD Lock/Unlock....................................... 23
Power Lock/Unlock .................................... 23
OSD Menu Functions................................. 23
OSD Control Options ................................. 24
Brightness .................................................. 24
Contrast ..................................................... 24
Sharpness .................................................. 24
Phase ......................................................... 24
Auto Adjust................................................. 24
OSD Left/Right ........................................... 24
OSD Up/Down ........................................... 24
Clock .......................................................... 24
Color Temperature..................................... 24
Current Input .............................................. 24
OSD Position ............................................. 24
Language ................................................... 24
Recall Defaults ........................................... 24
OSD Timeout ............................................. 24
Input Video Select ...................................... 24
Volume ....................................................... 24
Power Save(No Input) ............................... 25
Power LED Display & Power Saving ............ 25
General Power Saving Mode ..................... 25
Display Angle ...................................................... 25
Introduction
1
Product Description................................................. 1
Detailed LCD Display Performance
Requirements.......................................................... 2
Credit Card Reader ........................................... 2
External 12 VDC Power Supply ........................ 3
Chapter 2
Installation and Setup
5
Unpacking Your Touchmonitor. .............................. 5
Product Overview.................................................... 6
Front View ......................................................... 6
Rear View ......................................................... 7
Side View .......................................................... 7
Base Bottom View............................................. 7
Kensington™ Lock ............................................ 8
USB Interference Connection ................................. 9
Remove the Back Cover ................................... 9
Replace the Cable Cover .................................. 12
Optimizing the LCD Display .................................... 14
Installing the Peripheral Device Drivers .................. 14
Magnetic Stripe Reader.................................. 14
Testing the USB MSR Keyboard Emulation ... 14
Testing the USB-HID Class MSR ................... 14
Convert MSR from HID to
Chapter 4
Troubleshooting
Keyboard Emulation ....................................... 15
Installing the Touch Driver Software ....................... 19
Installing the USB Touch Driver ........................ 19
27
Solutions to Common Problems ......................... 27
Installing APR USB Touch Driver for Windows
Appendix A
XP .................................................................... 19
Installing the USB Touch Driver for Windows
XP, Windows 2000, Me, 98............................... 20
Native Resolution
29
31
Appendix B
Touchmonitor Safety
Care and Handling of Your Touchmonitor .......... 32
Chapter 3
Operation
21
About Touchmonitor Adjustments ........................... 21
LCD Function Key ................................................... 22
Appendix C
Technical Specifications
33
Touchmonitor Specifications ......................... 34
IntelliTouch Touchscreen
Specifications ................................................ 35
Infrared Touchscreen Specifications ............ 36
Acoustic Pulse Recognition Specifications ... 37
AccuTouch Touchmonitor Specifications ...... 38
Surface Capacity Touchscreen
Specifications ................................................ 39
15” LCD Touchmonitor
(1522L-XXXB-1-XX-G) Dimension ............... 40
Regulatory Information
Warranty
41
46
47
Index
C H A P T E R
1
INTRODUCTION
Product Description
The 1522L is a retail terminal designed to present information to the operator and the
customer. The 1522L is available in USB only. The 1522L functionally consists of a 15.
0” LCD main display with a touchscreen, an optional magnetic stripe reader (MSR), and
a two port USB Hub . The main display element is a 15” diagonal XGA resolution (1024
x 768) LCD display. The main display consists of an LCD Display and touchscreen.
1522L is available with Surface Capacitive, AccuTouch, IntelliTouch, CarrollTouch
infrared, and Acoustic Pulse Recognition (APR) touch technologies.
The MSR reads all three stripes on a standard credit card or drivers license. The credit
card is read by sliding the credit card, stripe side toward the display through the MSR
forward or backward. There is a USB MSR only.
The Hub provides two internal USB ports to be used by the MSR, and the touchscreen
for the USB version of the 1522L. The 1522L is powered by a universal AC power
source or 12 VDC from the external power source.
1-1
Detailed LCD Display Performance Requirements
15” TFT LCDDisplay Panel
Display Format
Display Area 15”
Pixel Pitch 15”
Contrast Ratio
Brightness
1024 x 768
304.1mm(H) x 228mm(V)
0.297mm(H) x 0.297mm(V)
Typical 500:1; min. 400:1
AccuTouch
Typical 200 cd/m2 ; min 160 cd/m2 (min)
Typical 230 cd/m2 ; min 184 cd/m2 (min)
Typical 210 cd/m2 ; min 168 cd/m2 (min)
Typical 230 cd/m2 ; min 184 cd/m2 (min)
Typical 230 cd/m2 ; min 184 cd/m2 (min)
8.5 ms/6 ms typical, 11 ms/10 ms max
16.2 M colors, with frame rate control
IntelliTouch
Surface Capacitive
CarrollTouch Infrared
APR
Response Time
Display Color
Vertical Viewing Angle
CR>=10
60o(up)/60o(down) typical
55o(up)/45o(down) typical
70o(up)/70o(down) typical
60o(up)/60o(down) typical
Horizontal Viewing Angle
CR>=10
Magnetic Stripe Reader
There is a USB MSR kit, which is sold separately. The USB version MSR is available in
Keyboard emulation or HID. The MSR reads all three stripes on a standard credit card
or driver’s license.
Reference Standards-Conform to
International Standards Organization, American National Standards
Applicable Standards
Institute, California Drivers License, American Association of Motor
Vehicle Administrators
ACCII
Message Format
Card Speed
3 to 50 IPS
MTBF Electronics
125,000 hrs; Head 1,000,000 passes
1-2 Elo Touchmonitor User Guide
External Power Supply
The 1522L shall be powered by a universal AC power source or 12 VDC from external
power source. The power supply shall provide the following capability:
AC power: Input voltage 85 to 265 Vac
Input frequency 47 to 63Hz
DC power: Input voltage 12 Vdc
Input line and load regulation +/-2%
1-3
1-4 Elo Touchmonitor User Guide
C H A P T E R
2
INSTALLATION AND SETUP
This chapter discusses how to install your LCD touchmonitor and how to install Elo
TouchSystems driver software.
Unpacking Your Touchmonitor
Check that the following items are present and in good condition:
Touchmonitor
USB Cable
European Power Cable
Video Cable
Speaker Cable
Power Cable US/Canadian
Elo QuickStatr
CD
Software
CD and Quick Installation Guide
2-5
Product Overview
Front View
Rear View
2-6 Elo Touchmonitor User Guide
Side View
Base Bottom View
2-7
KensingtonTM Lock
TM
The Kensington lock is a security device that help to prevent
theft. To find out more about this security device, go to http://
2-8 Elo Touchmonitor User Guide
USB Interface Connection
Your touchmonitor comes with only one touchscreen USB connector cable. (For Win-
dows 2000, Me, and XP systems only.)
To set up the display, please refer to the following figures and procedures:
Remove the Cable Cover
The cables are connected at the back of the monitor.
cable cover
To remove the cover, grasp the lip of the cover and pull towards you until it snaps off.
2-9
CAUTION
Before connecting the cables to your touchmonitor and PC, be sure that the
computer and touchmonitor are turned off.
NOTE
Before connecting the cables to the touchmonitor, route all the cables through
the hole as shown in the picture above.
The following illustrations guide you step by step in connecting your touchmonitor
using a USB cable connection.
Power cord
Connect one end of the power cord to the monitor and the other end to wall.
Connect the power cable to the power port in the monitor.
2-10 Elo Touchmonitor User Guide
Video cable
Connect one end of the video cable to the rear side of computer and the other to the
LCD monitor. Tighten by turning the two thumb screws clockwise to ensure proper
grounding.
Speaker cable
Connect one end of the speaker cable to the speaker port in the computer and the other
end to the port in the monitor.
2-11
USB cable
Connect one end of the USB cable to the rear side of the computer and the other to the
LCD monitor. The left port is for the MSR, and right port is for touch.
Replace the Cable Cover
Cable cover lip
cables
When you have attached all the cables to the monitor, gently bring all the cables toward
the stand so they fit under the cover lip.
Snap the Cable cover in place over the connections.
2-12 Elo Touchmonitor User Guide
Optimizing the LCD Display
To ensure the LCD display works well with your computer, configure the display mode
of your graphic card to make it less than or equal to 1024 x 768 resolution, and make
sure the timing of the display mode is compatible with the LCD display. Refer to
Appendix A for more information about resolution. Compatible video modes for your
touchmonitor are listed in Appendix C.
Installing the Peripheral Device Drivers
Magnetic Stripe Reader
No devices are needed.
Testing the USB MSR Keyboard Emulation
1 Plug in the device.
2 Open MS Word.
3 Slide the card through the MSR to view the data.
Testing the USB-HID Class MSR
1 On the CD, browse to Touch Monitor Peripherals\Magnetic Stripe Card
Readers\Demo.
2 Open the Readme.txt and follow instructions to test the unit.
2-13
Convert MSR from HID to keyboard emulation
MSR Conversion:
usb_swipe_insert_reader.asp
From the CD, select Touch Monitor Peripherals. Select the ET1529 HID-KB Conver-
sion folder, and follow the instructions in the folder.
1. To convert from HID to Keyboard Emulation Mode.
1.1
Double click on HID MSR icon on the desktop.
The following window will appear
1.2
Click on About to verify version
1.3
1.4
1.5
Close About dialog box.
Click on Read Cards.
This dialog will appear
2-14 Elo Touchmonitor User Guide
1.6
Swipe test card.
1.7
1.8
Close Read Cards dialog.
Click on Send Command. The following dialog box will appear
1.9
To send Inquiry MSR type
1.10 Type 00 10 into area under the heading Message (Hex)
1.11 Then click on Send Message.
2-15
1.12 The DATA=00 means it’s USB HID.
1.13 Switch to Keyboard Emulation
1.14 Type 01 10 01 into area under the heading Message (Hex)
1.15 Then click on Send Message.
1.16 Send inquiry MSR type
1.17 Type 00 10 into area under the heading Message (Hex)
1.18 Then click on Send Message.
1.19 The DATA=01 means its USB Keyboard Emulation.
1.20 You must now reset the MSR by sending the command 02.
1.21 Type 02 into area under the heading Message (Hex)
2-16 Elo Touchmonitor User Guide
1.22 Then click on Send Message.
1.23 Double click on The KB MSR Test icon in the desktop and slide the test c card.
The following icon will appear
1.24 Done.
2-17
Installing the Touch Driver Software
Elo TouchSystems provides driver software that allows your touchmonitor to work with
your computer. Drivers are located on the enclosed CD-ROM for the following operat-
ing systems:
• Windows XP
• Windows 2000
• Windows Me
• Windows 98
• Windows 95
• Windows NT 4.0
• CE 2.x, 3.0, 4x
• Windows XP Embedded
• Windows 3.x
• MS DOS
• OS/2
Additional drivers and driver information for other operating systems (including
com.
Your Elo USB touchmonitor is Plug-and-Play compliant. Information on the video
capabilities of your touchmonitor is sent to your video display adapter when Windows
starts. If Windows detects your touchmonitor, follow the instructions on the screen to
install a generic Plug-and-Play monitor.
Refer to the appropriate section for driver installation instructions.
Installing APR USB Touch Driver for Windows XP
Insert the ELO APR CD-ROM in your computer’s CD-ROM driver.
Follow the directions on the screen to complete the APR 2.0 driver setup for your
version of Windows.
1 Click Start > Run.
2 Click the Browse button to locate the SW600117.exe program on the CD-ROM.
3 Click Open, then OK to run SW600117.exe.
4 Follow the directions on the screen to complete the driver setup for your version
of Windows.
2-18 Elo Touchmonitor User Guide
Installing the USB Touch Driver
Installing the USB Touch Driver for Windows XP, Windows 2000,
Me and 98
1 Insert the Elo CD-ROM in your computer’s CD-ROM drive.
If Windows XP, Windows 2000,Windows 98, or Windows Me starts the Add New
Hardware Wizard:
2 Choose Next. Select “Search for the best driver for your device (recommended)” and
choose Next.
3 When a list of search locations is displayed, place a checkmark on “Specify a
location” and use Browse to select the \EloUSB directory on the Elo CD-ROM.
4 Choose Next. Once the Elo TouchSystems USB touchscreen driver has been detected,
choose Next again.
5 You will see several files being copied. Insert your Windows 98 CD if prompted.
Choose Finish.
If Windows XP, Windows 2000,Windows 98, or Windows Me does not start the Add
New Hardware Wizard:
NOTE:
For Windows XP and Windows 2000 you must have administrator access
rights to install the driver.
1 Insert the Elo CD-ROM in your computer’s CD-ROM drive. If the AutoStart feature
for your CD-ROM drive is active, the system automatically detects the CD and starts
the setup program.
2 Follow the directions on the screen to complete the driver setup for your
version of Windows. If the AutoStart feature is not active:
1
2
3
4
Click Start > Run.
Click the Browse button to locate the EloCd.exe program on the CD-ROM.
Click Open, then OK to run EloCd.exe.
Follow the directions on the screen to complete the driver setup for your
version of Windows.
2-19
2-20 Elo Touchmonitor User Guide
C H A P T E R
3
OPERATION
About Touchmonitor Adjustments
Your touchmonitor will unlikely require adjustment. Variations in video output and
application may require adjustments to your touchmonitor to optimize the quality of the
display. For best performance, your touchmonitor should be operating in its native
resolution, which is 1024 x 768 at 60-75 Hz. Use the Display control panel in Windows
to choose 1024 x 768 resolution. Operating in other resolutions will degrade video
performance. For further information, please refer to Appendix A.
All adjustments you make to the controls are automatically memorized. This feature
saves you from having to reset your choices every time you unplug or power your
touchmonitor off and on. If there is a power failure your touchmonitor settings will not
default to the factory specifications. To restore factory set up, choose it from the OSD.
See page 3-26.
3-21
LCD Function Key
5
4
3
2
1
Controls
Function
1
2
Power Switch
Select
Turns the display system power on or off.
Displays the OSD menus on the screen and used to input the OSD control options
on the screen.
3
4
5
Adjusts the decreasing value of the selected OSD control option.
Adjusts the increasing value of the selected OSD control option.
Menu display and menu exit.
Menu
3-22 Elo Touchmonitor User Guide
Controls and Adjustment
OSD Lock/Unlock
You are able to lock and unlock the OSDfeature. The monitor is shipped in the unlocked
position.
To lock the OSD:
1 Press the Menu button and button simultaneously for 2 seconds. A window will
appear displaying “OSD Unlock”. Continue to hold the buttons down for another 2
seconds and the window toggles to “OSD Lock”.
Power Lock/Unlock
You are able to lock/unlock the power feature. The monitor is shipped in the
unlocked position.To lock the power:
1 Press the Menu button and the
simultaneously for 2 seconds. A window for another
2 seconds and the window toggles to —”Power Lock“.
OSD Menu Functions
To display the OSD Menu press the Menu button.
1 Press the button or button to select the different OSD control option.
2 When the function you want to change is displayed, press the Select button.
To adjust the Value of the function:
1 Pressing the
button increases the value of the selected OSD control option.
2 Pressing the button decreases the value of the selected OSD control option.
After adjusting the values, the monitor will automatically save the changes.
NOTE:
The OSD screen will disappear if no input activities are detected for 45 seconds.
3-23
OSD Control Options
Brightness
• Background luminance of the LCD panel is adjusted.
Contrast
• Adjusts the contrast or the values of color gain (red, green or blue).
Sharpness
• The sharpness can be adjustable.
Phase
• Adjusts the phase of the dot clock.
Auto Adjust
• Clock system auto adjustment (under 5 seconds).
OSD Left/Right
• The OSD screen is moved horizontally right and left.
OSD Up/Down
• The OSD screen is moved vertically up and down.
Clock
• Adjusts the ratio of dividing frequency of the dot clock.
Color Temperature
• Sets R, G, B gain.
Current Input
• The frequency of the horizontal/vertical synchronizing signal under the input
indicated. (This information is under the Auto Adjust icon)
OSD Position
• Allows the OSD indicator position to be selected.
Language
• Select the language used for the OSD menu from among English, French, German,
Spanish and Japanese.
Recall Defaults
• All data copy from factory shipment data.
OSD Timeout
• Adjusts time for OSD menu to disappear.
Input Video Select
• Select D-SUB analog, DVI digital signal.
Volume
• To increase or decrease the sound level.
3-24 Elo Touchmonitor User Guide
Power-Save (No Input)
• The LCD panel background is cut when there is no signal input (AC line power
consumption of 4w or less).
Power LED Display & Power Saving
General Power Saving Mode
When the power switch is on, this LED light is green.
The LED indicates the different power status with altered LED colors when the monitor
operates in different modes (see following table).
Power
Mode
On
Consumption
30w max.
4w max.
2w
Indicator
Green
Sleep
Off
Orange
NO
We recommend switching the monitor off when it is not in use for a long period of time.
Display Angle
For viewing clarity, you can tilt the LCD forward up 67 to 90 degrees.
3-25
Tilt 15o from vertical
Tilt 30o from vertical
CAUTION
In order to protect the LCD, be sure to hold the base when adjusting the LCD,
and take care not to touch the screen.
3-26 Elo Touchmonitor User Guide
C H A P T E R
4
TROUBLESHOOTING
If you are experiencing trouble with your touchmonitor, refer to the following table. If
the problem persists, please contact your local dealer or our service center. Elo Techni-
cal Support numbers are listed on the last page of this manual.
Solutions to Common Problems
Problem
Suggestion(s)
The monitor does not respond after
you turn on the system.
Check that the monitor’s Power Switch is on.
Turn off the power and check the monitor’s power cord and signal
cable for proper connection.
Characters on the screen are dim
The screen is blank
Refer to the Controls and Adjustments section to adjust the brightness.
During operation, the monitor screen may automatically turn off as a
result of the Power Saving feature. Press any key to see if the screen
reappears.Refer to the Controls and Adjustments section to adjust the
brightness.
OSD or power buttons don’t work
“Out of Range” display
Check to see that they are not locked out. See page 3-25.
check to see of the resolution or vertical frequency of your computer is
higher than that of the LCD display.Reconfigure the resolution of your
computer to make it less than or equal to 1024 x 768. 1024 x 768 is
optimal. See Appendix A for more information on resolution.
Make sure cable is securely attached at both ends.
Touch doesn’t work
4-27
4-28 Elo Touchmonitor User Guide
C H A P T E R
A
NATIVE RESOLUTION
The native resolution of a monitor is the resolution level at which the LCD panel is
designed to perform best. For the Elo LCD touchmonitor, the native resolution is 1024
x 768 for the 15” size. In almost all cases, screen images look best when viewed at their
native resolution. You can lower the resolution setting of a monitor but not increase it.
Input Video
15.0" LCD
640 x 480 (VGA)
800 x 600 (SVGA)
1024 x 768 (XGA)
Transforms input format to 1024 x 768
Transforms input format to 1024 x 768
Display in native resolution
The native resolution of an LCD is the actual number of pixels horizontally in the LCD
by the number of pixels vertically in the LCD. LCD resolution is usually represented by
the following symbols:
VGA
640 x 480
800 x 600
1024 x 768
SVGA
XGA
A-29
As an example, a SVGA resolution LCD panel has 800 pixels horizontally by 600 pixels
vertically. Input video is also represented by the same terms. XGA input video has a
format of 1024 pixels horizontally by 768 pixels vertically. When the input pixels con-
tained in the video input format match the native resolution of the panel, there is a one to
one correspondence of mapping of input video pixels to LCD pixels. As an example, the
pixel in column 45 and row 26 of the input video is in column 45 and row 26 of the LCD.
For the case when the input video is at a lower or higher resolution than the native
resolution of the LCD, the direct correspondence between the video pixels and the LCD
pixels is lost. The LCD controller can compute the correspondence between video pix-
els and LCD pixels using algorithms contained on its controller. The accuracy of the
algorithms determines the fidelity of conversion of video pixels to LCD pixels. Poor
fidelity conversion can result in artifacts in the LCD displayed image such as varying
width characters.
A-30 Elo Touchmonitor User Guide
C H A P T E R
B
TOUCHMONITOR SAFETY
This manual contains information that is important for the proper setup and maintenance
of your touchmonitor. Before setting up and powering on your new touchmonitor, read
through this manual, especially Chapter 2 (Installation and Setup), and Chapter 3
(Operation).
1 To reduce the risk of electric shock, follow all safety notices and never open the
touchmonitor case.
2 Turn off the product before cleaning.
3 Your new touchmonitor is equipped with a three-wire, grounding power cord. The
power cord plug will only fit into a grounded outlet. Do not attempt to fit the plug into
an outlet that has not been configured for this purpose. Do not use a damaged power
cord. Use only the power cord that comes with your Elo TouchSystems touchmonitor.
Use of an unauthorized power cord may invalidate your warranty.
4 The slots located on the sides and top of the touchmonitor case are for ventilation. Do
not block or insert anything inside the ventilation slots.
5 It is important that your touchmonitor remains dry. Do not pour liquid into or onto
your touchmonitor. If your touchmonitor becomes wet do not attempt to repair it
yourself.
B-31
Care and Handling of Your Touchmonitor
The following tips will help keep your Elo touchmonitor functioning at the optimal
level.
• To avoid risk of electric shock, do not disassemble the brick supply or display unit
cabinet. The unit is not user serviceable. Remember to unplug the display unit from
the power outlet before cleaning.
• Do not use alcohol (methyl, ethyl or isopropyl) or any strong dissolvent. Do not use
thinner or benzene, abrasive cleaners or compressed air.
• To clean the display unit cabinet, use a cloth lightly dampened with a mild detergent.
• Avoid getting liquids inside your touchmonitor. If liquid does get inside, have a
qualified service technician check it before you power it on again.
• Do not wipe the screen with a cloth or sponge that could scratch the surface.
• To clean the touchscreen, use window or glass cleaner. Put the cleaner on the rag and
wipe the touchscreen. Never apply the cleaner directly on the touchscreen .
B-32 Elo Touchmonitor User Guide
C H A P T E R
C
TECHNICAL SPECIFICATIONS
Display Modes
Your Elo touchmonitor is compatible with the following standard video modes:
Item Resolution
Type
H. Scan(KHz)
31.469
31.469
31.469
37.861
37.500
35.156
37.879
48.077
46.875
48.363
56.476
60.023
V. Scan(Hz)
70.087
70.087
59.940
72.809
75.000
56.250
60.317
72.188
75.000
60.004
70.069
75.029
Pol.
+ /
1
640 x 350
720 x 400
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
800 x 600
1024 x 768
1024 x 768
1024 x 768
VGA
2
VGA
- / +
- /
3
VGA
4
VESA72
VESA75
SVGA
SVGA
VESA72
VESA75
XGA
-/
5
-/
6
+/+
+/+
+/+
+/+
-/-
7
8
9
10
11
12
XGA
-/-
VESA75
+/+
C-33
Touchmonitor Specifications
Model
1522L
LCDDisplay
Display Size
Pixel Pitch
Display Mode
15.0” TFT Active Matrix Panel
304.1(H) x 228(V) mm
0.297(H) x 0.297(V) mm
VGA 640 x 350 (70 Hz)
VGA 720 x 400 (70 Hz)
VGA 640 x 480 (60 / 72 / 75 Hz)
SVGA 800 x 600 (56 / 60 / 72 / 75Hz)
XGA 1024 x 768 (60 / 70 / 75Hz)
XGA 1024 x 768
Native
Contrast Ratio
500 : 1 (typical); min. 400:1
Brightness
AccuTouch
Typical 200 cd/m2; min. 160 cd/m2
Typical 230 cd/m2; min. 184 cd/m2
Typical 230 cd/m2; min. 184 cd/m2
Typical 210 cd/m2; min. 168 cd/m2
Typical 230 cd/m2; min. 184 cd/m2
8.5/6 ms typical, 11 ms/10 ms max.
16.2M colors, with frame rate control
(L/R)= -70o/+70o (typical), (U/D) -60o/+60o (typical)
IntelliTouch
CarrollTouch Infrared
Surface Capacitive
Acoustic Pulse Recognition (APR)
Response Time Rise/Fall
Display Color
Viewing Angle
Input Signal
CR>=10
VGAAnalog Video R.G.B. Analog 0.7V peak to peak
Sync
TTL Positive or Negative, Composite Sync, Sync on green
Signal Connector
Front Control
OSD
15 Pin D-Sub
Power on / off , Menu,
,
, Select
Contrast, Brightness, H/V-Position, Recall default,
Color Temperature, Volume, Sharpness,
Phase, Clock OSD H/V position, OSD Time, Auto Adjust,
OSD Language, Input Select
Plug & Play
DDC 2B
Touch Panel (optional)
Power
AccuTouch, IntelliTouch, Surface Capacitive, CarrollTouch, APR
Input: AC 85-265V, 47-63Hz, or DC 12V/4A (max.)
0oC ~ 40oC (41oF ~ 95oF)
Operating Conditions
Temp
Humidity
20% ~ 80% (No Condensation)
Altitude To 12,000 Feet
Dimensions (HxWxD)
Weight (Net)
354 x 286 x 265mm
20.1lbs., monitor weight 16.2 lbs.
CE, C-Tick, FCC, VCCI(Class B)
CB, CE, cULus, S(Argentina), Semko S Mark
Certifications
EMC
Safety
C-34 Elo Touchmonitor User Guide
IntelliTouch Touchscreen Specifications
Mechanical
Positional Accuracy
Standard deviation of error is less than 0.080 in. (2.03 mm).
Equates to less than ±1%.
Touchpoint Density
More than 100,000 touchpoints/in2 (15,500 touchpoints/cm2).
Typically less than 3 ounces (85 grams).
Touch Activation Force
Surface Durability
Surface durability is that of glass, Mohs’ hardness rating of 7.
No known wear-out mechanism, as there are no layers, coatings,
or moving parts. IntelliTouch technology has been operationally
tested to more than 50 million touches in one location without
failure, using a stylus similar to a finger.
Expected Life Performance
Sealing
Unit is sealed to protect against splashed liquids, dirt, and dust.
Optical
Light Transmission (per ASTM
D1003)
92%
Visual Resolution
All measurements made using USAF 1951 Resolution Chart,
under 30X magnification, with test unit located approximately
1.5 in (38 mm) from surface of resolution chart.
Clear surface: Excellent, with no noticeable degradation.
Antiglare surface: 6:1 minimum.
Gloss (per ASTM D2457
using a 60-degree gloss meter)
Antiglare surface: Curved: 60 ± 20 gloss units or 75 ± 15 gloss
units.
Environmental
Chemical Resistance
The active area of the touchscreen is resistant to all chemicals
that do not affect glass, such as:
Acetone
Toluene
Methyl ethyl ketone
Isopropyl alcohol
Methyl alcohol
Ethyl acetate
Ammonia-based glass cleaners
Gasoline
Kerosene
Vinegar
Electrostatic Protection (per
EN 61 000-4-2, 1995)
Meets Levels 4 (15kV air/8 kV contact discharge)
C-35
CarrollTouch Infrared Touchscreen Specifications
Mechanical
Input Method
Electrical
Finger or gloved hand activation
Positional Accuracy
Resolution
Typical centroid accuracy: 2 mm with 1 mm STD error
Touchpoint density is based on controller resolution of 4096 x 4096
No minimum touch activation force is required
Board: Serial (RS232) or USB 1.1
Touch Activation Force
Controller
Optical
Light Transmission
Chemical Resistance
Glass overlay: 92% per ASTM D1003-92 Environmental
Glass overlays: The touch active area of the touchscreen is
resistant to chemicals that do not affect glass, such as: acetone,
toluene, methyl ethyl ketone, isopropyl alcohol, methyl alcohol,
ethyl acetate, ammonia-based glass cleaners, gasoline, kerosene,
vinegar. Polycarbonate bezel: around perimeter of display has
some sensitivity to hydrocarbons.
Durability
Surface Durability
Glass filter option: Surface durability is that of glass, Mohs’
hardness rating of 7.
C-36 Elo Touchmonitor User Guide
Acoustic Pulse Recognition Specifications
Mechanical
Input Method
Electrical
Finger, finger nail, gloved hand, or stylus activation
Position Accuracy
Resolution Accuracy
Touch Activation Force
Controller
1% max. error
Touchpoint density is based on controller resolution of 4096 x 4096
Typically 2 to 3 ounces (55 to 85 grams)
Board: USB 1.1
Optical
Light Transmission
Environmental
Chemical resistance
90%+/-5%
The touch activation area of the touchscreen is resistant to chemicals
that do not affect glass such as: acetone, toluene, methyl ethyl ketone,
isopropyl alcohol, methyl alcohol, ethyl acetate, ammonia-based glass
cleaners, gasoline, kerosene, vinegar
Durability
Surface Durability
Expected Life
Surface durability is that of glass, Mohs’ hardness rating of 7
No known wear-out mechanism, as there are no layers, coatings, or moving
parts. APR technology has been operationally tested to more than 50
million touches in one location without failure, using a stylus similar
finger.
C-37
AccuTouch Touchmonitor Specifications
Mechanical
Construction
Top: Polyester with outside hard-surface coating with clear or
antiglare finish.
Inside: Transparent conductive coating.
Bottom: Glass substrate with uniform resistive coating. Top and
bottom layers separated by Elo-patented separator dots.
Standard deviation of error is less than 0.080 in. (2.03 mm). This equates
to less than ±1%.
Positional Accuracy
Touchpoint Density
Touch Activation Force
Surface Durability
More than 100,000 touchpoints/in2 (15,500 touchpoints/cm2).
Typically less than 4 ounces (113 grams).
Meets Taber Abrasion Test (ASTM D1044), CS-10F wheel, 500 g.
Meets pencil hardness 3H.
Expected Life
Performance
AccuTouch technology has been operationally tested to greater than
35 million touches in one location without failure, using a stylus
similar to a finger.
Optical
Light Transmission
(per ASTM D1003)
Visual Resolution
Typically80% at 550-nm wavelength (visible light spectrum).
All measurements made using USAF 1951 Resolution Chart, under 30
X magnification, with test unit located approximately 1.5 in. (38 mm)
from surface of resolution chart.
Antiglare surface: 6:1 minimum.
Haze (per ASTM D1003)
Gloss (per ASTM D2457)
Antiglare surface: Less than 15%.
Antiglare surface: 90 ± 20 gloss units tested on a hard-coated front
surface.
C-38 Elo Touchmonitor User Guide
Surface Capacitive Touchscreen Specifications
Mechanical
Input method
Glass Thickness
Electrical
Finger
0.118" / 3.0 mm nominal. (Glass only, not including tape, wires and/or solder if used)
Positional Accuracy
Reported touch coordinates are within 1.5% of true position (based on viewing area
dimensions)
Resolution
Controller
Touchpoint density is based on controller resolution of 4096 x 4096
Controller board size of 2.1" x 3.3" (5.4 x 8.4 cm), with auto-detect function for
Serial (RS232) and USB 1.1 connection
Optical
Up to 85% per ASTM D1003
Environmental
Temperature
Touchscreen Operating: –15oC to 70oC
Storage: –50oC to 85oC
Controller
Operating: 0oC to 65oC
Storage: –25oC to 85oC
Relative Humidity
Chemical Resistance
Agency Approvals
Sealability
Operating/Storage: 10% to 90% RH, noncondensing
Water, ammonia, isopropyl alcohol, and similar non-abrasive cleaners
UL, cUL, TUV, CE, FCC Class A & B, CISPR B
Can be sealed to meet NEMA 4 and 12 and IP 65 standards
Durability
Surface Durability
Anti-glare hardcoat cannot be scratched using any stylus with Mohs rating equal to or
less than 6. Tested in the laboratory to withstand over 160 million (mechanically simulated)
touches without noticeable degradation.
C-39
15” LCD Touchmonitor(1522L-XXXB-1-XX-G) Dimensions
C-40 Elo Touchmonitor User Guide
REGULATORY INFORMATION
I. Electrical Safety Information:
A) Compliance is required with respect to the voltage, frequency, and current require-
ments indicated on the manufacturer’s label. Connection to a different power source
than those specified herein will likely result in improper operation, damage to the equip-
ment or pose a fire hazard if the limitations are not followed.
B) There are no operator serviceable parts inside this equipment. There are hazardous
voltages generated by this equipment which constitute a safety hazard. Service should
be provided only by a qualified service technician.
C) This equipment is provided with a detachable power cord which has an integral safety
ground wire intended for connection to a grounded safety outlet.
1) Do not substitute the cord with other than the provided approved type. Under
no circumstances use an adapter plug to connect to a 2-wire outlet as this will
defeat the continuity of the grounding wire.
2) The equipment requires the use of the ground wire as a part of the safety
certification, modification or misuse can provide a shock hazard that can result
in serious injury or death.
3) Contact a qualified electrician or the manufacturer if there are questions about
the installation prior to connecting the equipment to mains power.
II. Emissions and Immunity Information
A) Notice to Users in the United States: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules.
These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate radio fre-
quency energy, and if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
B) Notice to Users in Canada: This equipment complies with the Class B limits for radio
noise emissions from digital apparatus as established by the Radio Interference Regula-
tions of Industrie Canada.
C) Notice to Users in the European Union: Use only the provided power cords and
interconnecting cabling provided with the equipment. Substitution of provided cords
and cabling may compromise electrical safety or CE Mark Certification for emissions or
immunity as required by the following standards:
41
This Information Technology Equipment (ITE) is required to have a CE Mark on
the manufacturer’s label which means that the equipment has been tested to the
following Directives and Standards:
This equipment has been tested to the requirements for the CE Mark as required
by EMC Directive 89/336/EEC indicated in European Standard EN 55 022 Class
B and the Low Voltage Directive 2006/95/EC.
D) General Information to all Users: This equipment generates, uses and can radiate
radio frequency energy. If not installed and used according to this manual the equipment
may cause interference with radio and television communications. There is, however, no
guarantee that interference will not occur in any particular installation due to site-spe-
cific factors.
1) In order to meet emission and immunity requirements, the user must observe
the following:
a) Use only the provided I/O cables to connect this digital device with any
computer.
b) To ensure compliance, use only the provided manufacturer’s approved
line cord.
c) The user is cautioned that changes or modifications to the equipment
not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
2) If this equipment appears to cause interference with radio or television reception, or
any other device:
a) Verify as an emission source by turning the equipment off and on.
b) If you determine that this equipment is causing the interference, try to
correct the interference by using one or more of the following measures:
i) Move the digital device away from the affected receiver.
ii) Reposition (turn) the digital device with respect to the affected
receiver.
iii) Reorient the affected receiver’s antenna.
iv) Plug the digital device into a different AC outlet so the digital
device and the receiver are on different branch circuits.
v) Disconnect and remove any I/O cables that the digital device
does not use. (Un-terminated I/O cables are a potential source of
high RF emission levels.)
vi) Plug the digital device into only a grounded outlet receptacle.
Do not use AC adapter plugs. (Removing or cutting the line cord
ground may increase RF emission levels and may also present a
lethal shock hazard to the user.)
If you need additional help, consult your dealer, manufacturer, or an experienced radio
or television technician.
42 Elo Touchmonitor User Guide
6K70
E141667
ITE
N
"The application of this monitor is restricted to special controlled luminous screen surface trend to reflect annoying light
of lamps and sunlight. To avoid these reflections the monitor should not be positioned in front of a window or directed to
luminaries. The monitor is in compliance with Reflection Class III according to ISO 13406-2"
This class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) This device must accept any interference received, including interference that
may cause undesired operation.
CAUTION:
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by
the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.
43
44 Elo Touchmonitor User Guide
WARRANTY
Except as otherwise stated herein or in an order acknowledgment delivered to Buyer,
Seller warrants to Buyer that the Product shall be free of defects in materials and
workmanship. With the exception of the negotiated warranty periods; the warranty for
the touchmonitor and components of the product is 3 years.
Seller makes no warranty regarding the model life of components. Seller’s suppliers
may at any time and from time to time make changes in the components delivered as
Products or components.
Buyer shall notify Seller in writing promptly (and in no case later than thirty
(30) days after discovery) of the failure of any Product to conform to the warranty set
forth above; shall describe in commercially reasonable detail in such notice the symp-
toms associated with such failure; and shall provide to Seller the opportunity to inspect
such Products as installed, if possible. The notice must be received by Seller during the
Warranty Period for such product, unless otherwise directed in writing by the Seller.
Within thirty (30) days after submitting such notice, Buyer shall package the allegedly
defective Product in its original shipping carton(s) or a functional equivalent and shall
ship to Seller at Buyer’s expense and risk.
Within a reasonable time after receipt of the allegedly defective Product and verification
by Seller that the Product fails to meet the warranty set forth above, Seller shall correct
such failure by, at Seller’s options, either (i) modifying or repairing the Product or (ii)
replacing the Product. Such modification, repair, or replacement and the return ship-
ment of the Product with minimum insurance to Buyer shall be at Seller’s expense.
Buyer shall bear the risk of loss or damage in transit, and may insure the Product. Buyer
shall reimburse Seller for transportation cost incurred for Product returned but not found
by Seller to be defective. Modification or repair, of Products may, at Seller’s option,
take place either at Seller’s facilities or at Buyer’s premises. If Seller is unable to modify,
repair, or replace a Product to conform to the warranty set forth above, then Seller shall,
at Seller’s option, either refund to Buyer or credit to Buyer’s account the purchase price
of the Product less depreciation calculated on a straight-line basis over Seller’s stated
Warranty Period.
45
THESE REMEDIES SHALL BE THE BUYER’S EXCLUSIVE REMEDIES FOR
BREACH OF WARRANTY. EXCEPT FOR THE EXPRESS WARRANTY SET
FORTH ABOVE, SELLER GRANTS NO OTHER WARRANTIES, EXPRESS OR
IMPLIED BY STATUTE OR OTHERWISE, REGARDINGTHE PRODUCTS, THEIR
FITNESS FOR ANY PURPOSE, THEIR QUALITY, THEIR MERCHANTABILITY,
THEIR NONINFRINGEMENT, OR OTHERWISE. NO EMPLOYEE OF SELLER
OR ANY OTHER PARTY IS AUTHORIZED TO MAKE ANY WARRANTY FOR
THE GOODS OTHER THAN THE WARRANTY SET FORTH HEREIN. SELLER’S
LIABILITY UNDER THE WARRANTY SHALL BE LIMITED TO A REFUND OF
THE PURCHASE PRICE OF THE PRODUCT. IN NO EVENT SHALL SELLER BE
LIABLE FOR THE COST OF PROCUREMENT OR INSTALLATION OF SUBSTI-
TUTE GOODS BY BUYER OR FOR ANY SPECIAL, CONSEQUENTIAL,
INDIRECT, OR INCIDENTAL DAMAGES.
Buyer assumes the risk and agrees to indemnify Seller against and hold Seller harmless
from all liability relating to (i) assessing the suitability for Buyer’s intended use of the
Products and of any system design or drawing and (ii) determining the compliance of
Buyer’s use of the Products with applicable laws, regulations, codes, and standards.
Buyer retains and accepts full responsibility for all warranty and other claims relating to
or arising from Buyer’s products, which include or incorporate Products or components
manufactured or supplied by Seller. Buyer is solely responsible for any and all represen-
tations and warranties regarding the Products made or authorized by Buyer. Buyer will
indemnify Seller and hold Seller harmless from any liability, claims, loss, cost, or ex-
penses (including reasonable attorney’s fees) attributable to Buyer’s products or repre-
sentations or warranties concerning same.
46 Elo Touchmonitor User Guide
INDEX
Numerics
G
15.0" LCD Touchmonitor (1522L-XXWB-1-XX-G)
Dimensions, 44
General Power Saving Mode, 25
Gloss, IntelliTouch, 35
Mechanical, Acoustic Pulse Recognition, 37
Mechanical, Infrared Touchscreen, 36
Mechanical, IntelliTouch, 35
A
About Touchmonitor Adjustments, 21
Acoustic Pulse Recognition Specifications, 37
Auto Adjust, 24
I
Infrared Touchscreen Specifications, 36
Installation and Setup, 5
B
Installing APR USB Touch Driver for Windows XP, 16
Installing the Peripheral Device Drivers, 14
Installing the Touch Driver Software, 18
Installing the USB Touch Driver, 19
Installing the USB Touch Driver for Windows XP,
Windows 2000, Me and 98, 20
Base Bottom View, 7
Brightness, 24
C
Care and Handling of Your Touchmonitor, 32
Chemical Resistance, IntelliTouch, 35
Cleaning Your Touchmonitor, 32
Clock, 24
IntelliTouch Touchscreen Specifications, 35
K
Color Temperature, 24
Contrast, 24
Kensington™ Lock, 8
Controls and Adjustment, 23
Credit Card Reader, 2
Current Input, 24
L
Language, 24
Light Transmission, IntelliTouch, 35
D
M
Detailed LCDDisplay Performance Requirements, 2
Display Angle, 25
Magnetic Stripe Reader, 14
Main Unit, 6
Display Modes, 33
Mechanical, 45
E
Electrical Safety Information, 41
Electrostatic Protection, IntelliTouch, 37
Emissions and Immunity Information, 41
Environmental, 35
Expected Life Performance, IntelliTouch, 35
External 12 VDC Power Supply, 3
I N D E X - 47
N
T
Native Resolution, 29
Technical Specifications, 35
Testing the USB MSR Keyboard Emulation, 14
Testing the USB-HID Class MSR, 14
Touch Activation Force, Acoustic Pulse Recognition, 37
Touch Activation Force, CarrollTouch Infrared
Touchscreen, 36
O
Optical, Acoustic Pulse Recognition, 37
Optical, Infrared Touchscreen, 36
Optical, IntelliTouch, 35
Optimizing the LCD Display, 14
OSD Control Options, 24
OSD Left/Right, 24
Touch Activation Force, IntelliTouch, 35
Touch not working, 27
Touchmonitor Safety, 41
Touchmonitor Specifications, 34
Touchpoint Density, IntelliTouch, 35
Troubleshooting, 27
OSD Lock/Unlock, 23
OSD Menu Functions, 23
OSD Position, 24
OSD Timeout, 24
U
OSD Up/Down, 24
Unpacking Your Touchmonitor, 5
USB Interface Connection, 9
P
Phase, 24
V
Positional Accuracy, Acoustic Pulse Recognition, 37
Positional Accuracy, CarrollTouch Infrared
Touchscreen, 36
VGA, 29
Visual Resolution, IntelliTouch, 35
Positional Accuracy, IntelliTouch, 35
Power LEDDisplay & Power Saving, 25
Power Lock/Unlock, 23
W
Warranty, 45
Power-Save (No Input), 25
Product Description, 1
X
Product Overview, 6
XGA, 29
R
Rear View, 7
Recall Defaults, 23
Regulatory Information, 39
Remove the Back Cover, 13
Replace the Back Cover, 13
S
Sealing, IntelliTouch, 35
Sharpness, 24
Side View, 7
Solutions to Common Problems, 27
Surface Durability, Acoustic Pulse Recognition, 37
Surface Durability, CarrollTouch Infrared
Touchscreen, 36
Surface Durability, IntelliTouch, 35
Surface Capacitive Touchscreen Specifications, 39
SVGA, 29
I N D E X - 48
Check out Elo’s Web site!
Get the latest...
• Product information
• Specifications
• News on upcoming events
• Press release
• Software drivers
Getting in Touch with Elo
To find out more about Elo’s extensive range of touch solutions, visit our Web site at www.elotouch.com or simply call
the office nearest you:
USA & Headquarters
Elo TouchSystems
301 Constitution Drive,
Menlo Park, CA 94025
USA
Germany
Belgium
Japan
Elo TouchSystems GmbH & Co. KG
Haidgraben 6
Elo TouchSystems
Diestsesteenweg 692
B-3010 Kessel-Lo
Belgium
Touch Panel Systems K.K
Sun Homada Bldg. 2F
1-19-20 Shin-Yokohama
Kanagawa 222-0033
Japan
D-85521 Ottobrunn
Germany
TOUCH(800-356-8682)
Tel 650-361-4700
Tel +49(89)60822-0
Tel +32(16)35-2100
Fax +32(16)35-2101
Tel +81(45)478-2161
Fax +81(45)478-2180
Fax 650-361-4747
Fax +49(89)60822-150
|