AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 1
back of the monitor
WARN IN G
The title "WARNING" is used to inform the users of
possible causes that could inflict the injury, death, or
property damage to the patients.
CAUTION
The title "CAUTION" is used to inform the users of
possible causes that could inflict the patients although
it might not severe enough to cause deaths.
NOTE
The title "NOTE" is used to inform the users of items
that are of importance in terms of installation,
operation, or maintenance of the Equipment although
the failure does not inflict the bodily harm to the
patients.
ADAVN INT’LCORP.2003
“ELO” is a Registered trademark of Elo TouchSystems, Inc.,
All other trademarks are the property of their reference owners.
This document is subject to change without notice.
Advan provides this information as reference only. Reference to other vendor’s products
does not imply any recommendation or endorsement.
Revision Control
Date
Description
Document number
Rev. 4 112003
AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 3
Quick Setup (IBM/IBM Compatible under Windows 95/98/ME/2000)
Please Read Carefully When Setting Up Your New Monitor
Monitor Screen Adjustment and Resolution Setting Procedure for IBM/IBM Compatible
Computers with Windows based OS system.
Before adjusting the monitor, all the necessary drivers should be installed to your System
and resolution has to be set to manufacturer’s recommended preset of 1280 x 1024 @ 60Hz,
70Hz, 72Hz or 75 Hz.
To check the resolution, press the “SELECT UP” button on the monitor and the “Information”
will display under the OSD. Information will have Resolution, Horizontal and Vertical (Refresh
rate) frequency information.
To change the resolution to its factory recommended preset.
1. On a Windows 95, 98, ME or 2000, press right button on a Mouse to execute the Pop-up
menu.
2. Press “Properties” to execute the “Display Properties”
3. Press “Setting” and change the resolution to 1280 x 1024.
4. Press “Apply or OK” to select and press “OK” to keep the selected resolution.
5. Go back to “Display Properties” - “Setting” - “Advanced properties” - “Adapter”
6. On Adapter property, change the refresh rate to 60Hz, 70Hz, 72Hz or 75Hz. If you don’t
have these options, choose “Adapter Default”. (60Hz recommended)
Screen Adjustment Procedure
1. Press the “AUTO” button.
2. If you still don’t have a clear display monitor, please refer to step 3.
3. Start “Shut Down” in Windows 95/98/ME/2000 - It will display moire on screen
4. Press “Up” or “Down” button then the OSD menu will pop-up.
5. Adjust the “Frequency” under the OSD to reduce or get rid of the vertical display noise
(Jail bars). (Page 16)
6. Once the vertical display noise disappears, press adjust the “Phase” to reduce or get rid of
the horizontal display noise (Snowy effect). (Page 16)
4
User’s Guide
Quick Setup (IBM/IBM Compatible under Windows NT 4.0)
Please Read Carefully When Setting Up Your New Monitor
Monitor Screen Adjustment and Resolution Setting Procedure for IBM/IBM Compatible
Computers with Windows based OS system.
Before adjusting the monitor, all the necessary drivers should be installed to your System
and resolution has to be set to manufacture’s recommended preset of 1280 x 1024 @ 60Hz,
70Hz, 72Hz or 75Hz.
To check the resolution, press the “SELECT UP” button on the monitor and the “Information”
will display under the OSD. Information will have Resolution, Horizontal and Vertical (Refresh
rate) frequency information.
To change the resolution to its factory recommended preset.
1. On a Windows NT 4.0, press right button on a Mouse to execute the Pop-up menu.
2. Press “Properties” to execute the “Display Properties”
3. Press “Setting” and change the resolution to 1280 x 1024.
4. Change “Refresh Frequency” to 60Hz, 70Hz, 72Hz or 75Hz. (60Hz recommended)
Screen Adjustment Procedure
1. Press the “AUTO” button.
2. If you still don’t have a clear display monitor, please refer to step 3.
3. Start “Shut Down” in Windows 95/98/ME/2000 - It will display moire on screen
4. Press “Up” or “Down” button then the OSD menu will pop-up.
5. Adjust the “Frequency” under the OSD to reduce or get rid of the vertical display noise
(Jail bars). (Page 16)
6. Once the vertical display noise disappears, press adjust the “Phase” to reduce or get rid of
the horizontal display noise (Snowy effect). (Page 16)
AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 5
Quick Setup (Macintosh)
Please Read Carefully When Setting Up Your New Monitor
1. Set your Macintosh Adapter on pages 23 and 24.
2. Push the “APPLE” icon on the upper left corn and execute Control Panel->
Monitors&Sound. Select “Thousands” for the Color Depth, Select “1280X1024, 60Hz,
70Hz, 72Hz or 75Hz” for the Resolution. (60Hz recommended)
*
On some Apple G3 or newer systems, you may not need to use the Macintosh Adapter.
Screen Adjustment Procedure
1. Press the “AUTO” button on the monitor.
6
User’s Guide
INTRODUCTION
Congratulations on your purchasing of the AMM17TK/AMM18TK/AMM19TK high
performance TFT LCD monitor.
FEATURES
The FPD is a TFT-LCD monitor that is intelligent, microprocessor-based and ergonomically
designed display, compatible with most analog RGB (Red, Green, Blue) display standards,
including PS/V, PS/2, Apple Macintosh Centris, Quadra, and Macintosh II family signals. The
LCD monitor is capable of displaying crisp and vibrant color graphics with VGA, SVGA, XGA,
SXGA (non-interlaced), and most Macintosh compatible color video cards.
•
Advanced Viewing Solution (AVS): Our sophisticated filter extends the viewing angle of
the screen image, without sacrificing contrast ratio and brightness.
•
AdvancedTiming Setup (ATS): Aunique technology from the One TouchAutoAdjustment.
Pressing the Auto Adjust button on the front panel, automatically optimizes position,
phase, clock, contrast and color balance. This allows the user to maximize the perfect
screen setting in the shortest amount of time.
•
•
Advanced Mounting Solution (AMS): Improve flat panel environment, utilizing numerous
ergonomic mounting solutions to allow creative use in conjunction to product application.
The monitor is able to properly function even in case of upgrade video cards or software
because of the wide auto-scanning compatibility range without requiring to buy a new
monitor.
•
The internal microprocessor digitally controls auto-scanning. For horizontal scan
frequencies between 24.8 KHz and 60.2 KHz, and vertical scan frequencies between
56.3 Hz and 85.1 Hz. In each frequency mode, the microprocessor-based circuitry allows
the monitor to function at the precision-of a fixed frequency.
•
•
•
•
•
The resident memory allows for storing factory default settings and also additional user
adjustment parameters.
The maximum resolution achievable is SXGA (1280 x 1024), best suited for Windows
applications
The compact and sleek cabinet design saves lot of your desk space and makes your desk
look neat and tidy.
The monitor is compliant with VESA-DPMS power management standard. In order to
save energy, the monitor must be connected to a system compliant with the standard.
The monitor is also compliant with the most stringent environmental scheme of TCO
95. In this scheme, no environmental harmful substances are used during the entire
manufacturing process.
The monitor is certified by UL International to medical standard UL2601-1. It is also CE
marked for sale into the European Community for integration or use with medical products. It
is certified by NEMKO according to EN60601-1 & EN60601-1-2 for sale to the medical market.
AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 7
UNPACKING
Please check the following items are present when you unpack the box, and save the packing
materials in case you will need to ship or transport the monitor in future.
•
AMM17TK,AMM18TK,AMM19TK orAMM19TK/HB LCD Monitor and two video
cable (1) VGA HDDB15 cable (1) DVI-D cable
AUTO
SELECT
•
•
AC Power cord
CAUTION
Manufacturer :Ault Korea
AC-Adapter
Model No : MW160 or MW116
•
•
Floppy Disk (for test pattern and set up)
User Manual
•
Composite Video (C-Video) Cable and Super Video (S-Video) Cable *Some Touchscreen
Model Not Available
8
User’s Guide
Symbol Explanations
This monitor is intended for use in Health Care Facilities.
Regulatory Compliance
This monitor has been tested to comply with IEC/EN 60601-1 and IEC/EN60601-1-2
By NEMKO and is certified by UL to medical standard UL2601-1(UL/cUL Mark).
Because many medical offices are located in residential areas, this monitor, in addition to the
medical requirements, has also been tested and found to comply with the limits for FCC Class
B computing devices in a typically configured system. It is the system integrator or
configurer’s responsibility to test and ensure that the entire system complies with applicable
EMC laws.
AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 9
EU Declaration of Conformity for Medical Applications
ADeclaration of Conformity has been filed for this product.Asample of this
document may be found in the addendum which accompanied this manual. For a
copy of the Declaration of Conformity document, please contactADVAN Int’l
Corp. and request forAMM17TK,AGMM18TK,AMM19TK and
AMM19TK/HB DOC.
Installation
Before you unpack your monitor, prepare a suitable workspace. You need a stable
and level surface near a grounded wall outlet in an area which is relatively free of
glare from sunlight or other sources of bright light. The monitor is cooled by natural
convection (it has no fan).
For optimum performance, do not block the cooling vents.
While unpacking the monitor, inspect it and other package contents for shipping
damage that could cause a fire or shock hazard. Immediately report any shipping
damage to the carrier or transportation company and contact customer service for
monitor in the future or in case of return.
After you unpack the monitor, make sure the following items are included
• Monitor with 1.5 meter(5ft)monitor-to computer video cable
• AC adapter with cable
CAUTION: AC Adapter must be plugged into Grounded a power outlet)
CAUTION : AC adapter
Manufacturer: Ault korea
Model No: MW160 or MW116
• Touchscreen cable if monitor has touchscreen option
• This operations manual
Note: Your system provider may offer alternative cords or cables
depending on the installation requirement and local geography issues.
10 User’s Guide
Equipment is not suitable for use in the presence of a flammable anesthetic mixture with air or
with oxygen or nitrous oxide.
No user serviceable parts inside, ask qualified personnel when accessing inside
For disposal of waste product, you must follow the requirement of local code.
Electrical input rating : 12V d.c. 6.67A
Classification
-
-
-
Type of protection against electric shock: Class I Equipment
Degree of protection against the ingress of water: Ordinary
Mode of operation: Continuous
Environmental conditions for transport and storage:
-
-
-
Temperature range within 20 oC to 60 oC
Relative humidity range within 10% to 90%
Atmospheric pressure range within 500 to 1060 hPa.
SCREEN POSITION ADJUSTMENT
In order to optimize the best viewing position, you can adjust the tilt of the monitor by using
both of your hands to hold the edges of the monitor as shown in the figure below. The moni-
tor can be adjusted to 28 degrees up as indicated by arrow below.
AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 11
SAFETY PRECAUTION
•
Avoid placing the monitor, or any other heavy object, on the power cord to prevent fire or
electrical shock from damage to the power cord.
•
•
Do not expose the monitor to rain, excessive moisture, or dust to avoid fire or shock hazard.
Do not cover the slots or openings of the monitor for proper heat dissipation. Always put
the monitor in a place where there is adequate ventilation.
•
Avoid placing the monitor against a bright background or where sunlight or other light
sources may reflect on the area of the monitor. Place the monitor just below eye level.
•
•
Handle with care when transporting the monitor.
Refrain from giving the shock or scratch to the screen, as screen is fragile.
CLEANING YOUR MONITOR
No specific liquid or chemical necessary when cleaning this LCD monitor
However, we suggest to clean the monitor with non-abrasive cloths and cleaning solutions
used in hospitals to clean similar equipment. We recommend using 70% Isopropyl alcohol
for the screen surface and warm water and a mild detergent for all other surfaces. Other
acceptable cleaning agents are listed below:
• 70% isopropyl alcohol
• 6% aqueous ammonia
• Cidex (2.4% glutaraldehyde solution)
• Sodium Hypochlorite (bleach) 10%
• “Green soap” USP
• 0.5% Chlorhexidine in 70% isopropyl alcohol
• Ovation
• Formula 409
• Fantastic
• Wex Cide
To clean the screen, do not spray liquid cleaners directly on to the unit. Stand away Form the
monitor and spray cleaning solution onto a cloth. Without applying excessive pressure,
clean the screen with the slightly dampened rag.
12 User’s Guide
PRESET MODES
To reduce the need for adjustment for different modes, the monitor has default setting modes
that are most commonly used as given in the table below. If any of these display modes are
detected, the monitor automatically adjusts the picture size and centering. When none of the
mode is matched, the user can store their preferred modes in the user modes. The monitor is
capable of storing up to 7 user modes. The only condition to store as a user mode is the new
display information must have 1 KHz difference for horizontal frequency or 1 Hz for vertical
frequency or the sync signal polarities are different from the default modes.
M ode
1
Resolution (H x V)
640 x 350
640 x 350
640 x 400
640 x 400
720 x 350
720 x 400
720 x 400
640 x 480
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1152 x 864
1280 x 960
1280x1024
1280x1024
H. Freq. (KHz)
31.5
37.9
31.5
37.9
31.5
31.5
37.9
31.5
37.9
37.5
43.3
35.1
37.9
48.1
46.9
53.7
35.5
48.4
56.5
60
V. Freq. (Hz)
70
85
70
85
70
70
85
60
72
75
85
56
60
72
75
85
43
60
70
75
85
75
60
60
75
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
68.7
67.5
60
63.9
79
AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 13
POWER MANAGEMENT FUNCTION
The monitor is equipped with the power management function which automatically reduce the
power consumption when not in use in three power level modes.
•
Stand-by Mode
The monitor goes into stand-by mode when the horizontal sync signal is off for about 10
seconds. In this mode, the screen goes off and the power LED blinks for 3 seconds On
and 1 second Off. The screen is displayed after the horizontal sync signal is restored.
•
Suspend Mode
The monitor goes into suspend mode when the vertical sync signal is off for about 10
seconds. The power consumption during this is less than 8 W. In this mode, the screen
goes off and the power LED blinks for 3 seconds On and 1 second Off. The screen is
displayed after the vertical sync signal is restored.
•
Off Mode
The monitor goes into power-off mode when the vertical and horizontal sync signals are
off for about 10 seconds. In this mode, the screen goes off and the power LED blinks for
3 seconds On and 1 second Off. The screen is displayed after the vertical and horizontal
sync signals are restored.
Power Management System
TheAMM17TK,AMM18TK,AMM19TK andAMM19TK/HB Medical Monitor complies
with the VESA DPMS power management proposal. The VESA DPMS proposal provides
four phases of power-saving modes by detecting the horizontal sync signal as shown in the
table blow.
M ode
D C Input Powe r
(monitor only)
A C Input powe r
(Incl. A C adapte r)
LED Status
O n
35 W max.
4.5 W max.
4.5 W max.
4.5 W max.
60 W max.
6 W max.
6 W max.
6 W max.
S teady G reen
Blinking G reen
Blinking G reen
Blinking G reen
S tandby
S upend
O n
When the monitor is power saving mode or detects an incorrect timing, the screen will be
blank and power LED indicator will blink.
14 User’s Guide
DDC
To make your installation easier, the monitor is able to Plug and Play with your system if your
system also supports DDC protocol. The DDC (Display Data Channel) is a communication
protocol through which the monitor automatically informs the host system about its
capabilities, for example, supported resolutions and corresponding timing. The monitor
supports DDC1 and DDC2B standard.
INSTALLATION
To install the monitor to your host system, please follow the steps as given below:
Steps
1. Use the VGA cable that provides D-SUB 15-pin connector and connect to the
15-pin connector on the VGA controller card.
2. Connect the DC power to the DC power connector on the monitor.
3. If use with USB hub, connect the loop cable between the monitor and the USB hub then
connect the DC power to the bottom of USB hub.
4. Connect one end of AC power cord into the AC Adapter and the other end to AC
power outlet. (See page 13)
5. Then turn the computer on and then the monitor.
6. If the monitor still does not function properly, please refer to the troubleshooting section
to diagnose the problem.
AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 15
Display for Video and Image Playback
Explains how to use ourAMM17TK,AMM18TK,AMM19TK andAMM19TK/HB to playVCR,
view television, video game, or digital camera images. It also show you how to connect video
and other types of video equipment to the display.
Connecting with Video Equipment
You can connect many types of video equipment to the display. The equipment must have
either Super video (S-video) ports or Composite video ports. To install the monitor to your
video equipment, please follow the steps as given below:
Steps
1. Make sure the video equipment has a Super video (S-video) or a Composite video connector.
2. Turn off the computer, display, and video equipment before any types of connection.
3. For composite video, plug one end of an RCA cable into the video out port on the video
equipment then connect the other end to the monitor video input port.
4. For S-video, plug one end of the S-video cable into the video out port on the video equipment
then connect the other end to the monitor S-video input port.
5. Connect the DC power to the DC power connector on the monitor.
6. Connect one end of AC power cord into the AC Adapter and the other end to AC
power outlet.
7. Then turn the video equipment on and then the monitor.
Connecting to a Television Signal
The display doesn’t have a tuner. To view television on the display, you need to use either the
VCR or TV tuner card in your computer to change channels.
Video and Sound
This monitor does have speakers for sound. If you’re using the display to play a video or view
television images, you need to connect the speakers to your television or video equipment
for sound.
16 User’s Guide
USER CONTROLS
Front Panel Controls
1. Power LED:
2. Power Switch:
3. +:
Lights up to indicate the power is turned ON.
To turn ON or OFF the power.
To increase the value of the parameter in the OSD you have selected for adjustment.
To increase the brightness directly when OSD menu is not activated.
To decrease the value of the parameter in the OSD you have selected for adjustment.
To increase the brightness directly when OSD menu is not activated.
To enter OSD menu then can use as moving upward in the OSD menu.
To move downward in the OSD menu.
4. -:
5. Select Up:
6. Select Down:
Switch PC display to Video display and vice versa by one touch when OSD menu is not activated.
One touch Auto adjust or Exit OSD menu.
7. Auto Button:
Standard OSD Operation
1. Press menu button to activate the OSD.
2. Use Select Up or Down keys to move up or down through the menu. The parameter will be highlighted wehn
selected.
3. Then use + or - to increase or decrease the value of the parameter, or make selection between different options.
4. To quit the OSD screen at any time during the operation, pressAuto button. If no keys are pressed for a time period,
the OSD automatically disappears.
AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 17
OSD Scren Basic Section (VGA)
For OSD display, push “Menu”. For selecting Icon, push “Up”
or “Down”
Push “Up” or “Down” button to select between Push “Up” or “Down” button to select between
“Brightness” or “Contrast” then push “Select”
Use “Left” or “Right” button to adjust
“Frequency” or “Phase” then push “Select”
Use “Left” or “Right” button to adjust
Push “Up” or “Down” button to select between “OSD
Hor. Pos.”, “OSD Ver. Pos.”, “OSD Background”, or
“User Timeout” then push “Select”
Push “Up” or “Down” button to select between
“Horizontal” or “Vertical” then push “Select”
Use “Left” or “Right” button to adjust
Use “Left” or “Right” button to adjust
Push “Left” or “Right” to select Color Temp betweenPush “Up” or “Down” button to select between
“5000”, “6500”, 7300”, “9500”, or “User” then push
“Select”
“DPMS”, “Auto Source Select”, or “Freeze Frame”
then push “Select” Use “Left” or “Right” button to
If “User” were slected, push “Up” or “Down” button to adjust
select between “Red”, “Green”, or “Blue” then push
“Select”
Use “Left” or “Right” button to adjust
18 User’s Guide
OSD Scren Basic Section (VGA)
For OSD display, push “Menu”. For selecting Icon, push “Up”
or “Down”
Push the select button
Use “Left” or “Right” button to adjust
Push the select button to execute the Zoom
function
Push “Up” or “Down” button to select between
“Analog RGB”, “Digital RGB”, “Composite Video” or
“Super Video”
Use “Left” or “Right” to choose the correct mode then
push “Select” button
Push the select button
Use “Left” or “Right” button to adjust
Push the select button to execute the Auto
Setup function or Push the select button to
execute Recall Factory Default
Push the select button to execute Information
AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 19
OSD Scren Basic Section (DVI)
For OSD display, push “Menu”. For selecting Icon, push “Up”
or “Down”
Push “Up” or “Down” button to select between “OSD
Hor. Pos.”, “OSD Ver. Pos.”, “OSD Background”, or
“User Timeout” then push “Select”
Push “Up” or “Down” button to select between
“Brightness” or “Contrast” then push “Select”
Use “Left” or “Right” button to adjust
Use “Left” or “Right” button to adjust
Push “Left” or “Right” to select Color Temp betweenPush “Up” or “Down” button to select between
“5000”, “6500”, 7300”, “9500”, or “User” then push
“Select”
“DPMS”, “Auto Source Select”, or “Freeze Frame”
then push “Select” Use “Left” or “Right” button to
If “User” were slected, push “Up” or “Down” button to adjust
select between “Red”, “Green”, or “Blue” then push
“Select”
Use “Left” or “Right” button to adjust
Push the select button
Use “Left” or “Right” button to adjust
Push the select button to execute the Zoom
function
20 User’s Guide
OSD Scren Basic Section (DVI)
For OSD display, push “Menu”. For selecting Icon, push “Up”
or “Down”
Push “Up” or “Down” button to select between
“Analog RGB”, “Digital RGB”, “Composite Video” or
“Super Video”
Use “Left” or “Right” to choose the correct mode then
Push the select button
Use “Left” or “Right” button to adjust
push “Select” button
Push the select button to execute Recall
Factory Default
Push the select button to execute Information
AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 21
OSD Scren Basic Section (C-Video or S-Video)
For OSD display, push “Menu”. For selecting Icon, push “Up”
or “Down”
Push “Up” or “Down” button to select between
“Brightness” or “Contrast” then push “Select”
Use “Left” or “Right” button to adjust
Push “Select” button then “Up” or “Down”
Push “Left” or “Right” button to adjust
Push “Up” or “Down” button to select between “OSD
Hor. Pos.”, “OSD Ver. Pos.”, “OSD Background”, or
“User Timeout” then push “Select”
Push “Up” or “Down” button to select between
“Horizontal” or “Vertical” then push “Select”
Use “Left” or “Right” button to adjust
Use “Left” or “Right” button to adjust
Push “Left” or “Right” to select Color Temp
Push “Up” or “Down” button to select between
between “5000”, “6500”, 7300”, “9500”, or “User” “DPMS”, “Auto Source Select”, “Freeze Frame”, or
then push “Select” “ADC Calibration” then push “Select”
If “User” were slected, push “Up” or “Down” button Use “Left” or “Right” button to adjust
to select between “Red”, “Green”, or “Blue” then
push “Select”
Use “Left” or “Right” button to adjust
22 User’s Guide
OSD Scren Basic Section (C-Video or S-Video)
For OSD display, push “Menu”. For selecting Icon, push “Up”
or “Down”
Push the select button
Push the select button
Use “Left” or “Right” button to adjust
Use “Left” or “Right” button to adjust
Push the select button
Use “Left” or “Right” button to adjust
Push the select button to execute Recall
Factory Default
Push the select button to execute Information
AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 23
OSD Function Description (Under Analog Display)
Item
Function Description
Brightness
Contrast
To increase or decrease the brightness.
To increase or decrease the contrast.
To adjust frequency (dot clock).
To adjust phase (clock-phase).
Frequency
Phase
Horizontal
Vertical
To move the screen left or right.
To move the screen upward or downward.
To move OSD menu left or right.
To move OSD menu upward or downward.
OSD Hor Pos
OSD Ver Pos
OSD Background Choose between Opaque or Translucent.
User Timeout
Color Temp
Set OSD screen appearing time.
Choose between 5000, 6500, 7300, 9500, or User for color
temp.
Red
Balance Red.
Green
Blue
Balance Green.
Balance Blue.
DPMS
Enable or Disable DPMS.
Adjust auto source select between off, low, or hight.
Auto Source
Select
Freeze Frame
Zoom
Enable or Disable freeze frame
Enable zoom-in function
Image Sharpness
Scale Mode
Set image sharpness from 1 to 5.
Choose scale mode between fill screen, aspect ratio, or one
to one
Input Source
Select
Choose input source between analog RGB, digital RGB,
composite video, or super video
Auto Adjust
The Auto-Adjust will automatically adjust V-Position, H-
Position, Clock,
Clock-Phase, and Contrast, the whole process takes about 5
seconds. (Please use the test pattern file in the attached LCD
monitor utility disk for Auto Adjust).
Recall Factory
Default
Set to factory default.
Infomation
Display information on resolution, refresh rate, and input
mode.
24 User’s Guide
OSD Function Description (Under Digital Display)
Ite m
Function D e scription
Brightness
To increase or decrease the brightness.
To increase or decrease the contrast.
To move the screen left or right.
Contrast
Horizontal
Vertical
To move the screen upward or downward.
To move O SD menu left or right.
To move O SD menu upward or downward.
Choose between Opaque or Translucent.
Set OSD screen appearing time.
OSD Hor Pos
OSD Ver Pos
OSD Background
User Timeout
Color Temp
Choose between 5000, 6500, 7300, 9500, or User for color
temp.
Red
Balance Red.
Green
Blue
Balance Green.
Balance Blue.
DPMS
Enable or Disable DPMS.
Adjust auto source select between off, low, or hight.
Auto Source
Select
Freeze Frame
Zoom
Enable or Disable freeze frame
Enable zoom-in function
Image Sharpness
Scale Mode
Set image sharpness from 1 to 5.
C hoose scale mode between fill screen, aspect ratio, or one
to one
Input Source
Select
Choose input source between analog RGB, digital RGB,
composite video, or super video
Recall Factory
Default
Set to factory default.
Infomation
Display information on resolution, refresh rate, and input
mode.
AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 25
OSD Function Description (Under C-Video or S-Video Display)
Ite m
Function D e s cription
Hue
To increase or decrease the hue level.
To increase or decrease the saturation level.
To increase or decrease the brightness.
To increase or decrease the contrast.
To move the screen left or right.
Saturation
Brightness
C ontrast
Horizontal
Vertical
To move the screen upward or downward.
To move O SD menu left or right.
O SD Hor Pos
O SD Ver Pos
O SD Background
User Timeout
C olor Temp
To move O SD menu upward or downward.
C hoose between O paque or Translucent.
Set O SD screen appearing time.
C hoose between 5000, 6500, 7300, 9500, or User for color
temp.
Red
Balance Red.
Green
Blue
Balance Green.
Balance Blue.
DPM S
Enable or Disable DPM S.
Adjust auto source select between off, low, or hight.
Auto Source
Select
Freeze Frame
Zoom
Enable or Disable freeze frame.
Enable zoom- in function.
Image Sharpness
Set image sharpness from 1 to 5.
Video Scale Mode C hoose video scale mode between normal, 4:3 scale mode,
or 16:9 scale mode.
Video Sharpness
To increase or decrease the video sharpness.
Input Source
Select
C hoose input source between analog RGB, digital RGB,
composite video, or super video
Recall Factory
Default
Set to factory default.
Infomation
Display information on resolution, refresh rate, and input
mode.
26 User’s Guide
TROUBLESHOOTING
Before sending your LCD monitor for servicing, please check the troubleshooting list below
to see if you can self-diagnose the problem.
Problems Current Status
LED ON
Remedy
Using OSD, adjust brightness and contrast to
maximum or reset to their default settings.
•
LED OFF
Check the power switch.
•
•
No
Picture
Check if AC power cord is properly
connected to the AC adapter.
LED Blinking
Check if video signal cable is properly
connected at the back of monitor.
•
Check if the power to computer system is ON.
•
•
Unstable Picture
Check if the specification of graphics adapter
and monitor is in compliance which may be
causing the input signal frequency mismatch.
Display is
Using Auto Setup button, if still display
abnormal picture then adjust CLOCK,
CLOCK-PHASE, H-POSITION and V-
POSITION with non-standard signals.
•
•
•
missing, center
shift, or too small
or too large in
Abnormal
Picture
display size
Using OSD, in case of missing full-screen
image, please select other resolution in your
Operating System (Windows 95/98, NT) or
other vertical refresh timing.
Must wait for a few seconds after adjusting
the size of the image before changing or
disconnecting the signal or powering OFF the
monitor.
AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 27
SPECIFICATION
AMM170TK
LCD Panel
Type
43.2cm/17-inch Color TFT Panel
Active Matrix
Resolution
1280 dots x 1024 lines (Recommended)
0.264mm
Pixel Pitch
Display Color
Response Time
Color Tone
Color Filter
Face Finishing
Viewing Angle
Video
16 million colors
25ms
Up to 256 tone
RGB vertical stripe type
Anti-Glare Hard Coated
170°H 170°V (CR>=10)
0.7Vp-p analog RGB & TMDS (PanelLink) Digital
165 MHz x 1
Input Signal
Sync
2.5~5.0Vp-p separated sync
Input Impedance (Analog)
Video - 75 Ohm
Sync - 1k Ohm
Composite Sync
Digital
C-Video, S-Video
3 channel TMDS receiver, single pixel 24 bit MSB-
aligned RGB TFT
Scanning Frequency
Horizontal
30~68kHz
Vertical
56~85Hz (UP to 85Hz at 1024 x 768 mode and up to
75Hz at 1280 x 1024)
Display Size
H x V
13.3" x 10.6" (337.92mm x 270.33mm)
Brightness, Contrast Radtio, Gray Scales
Brightness
250 cd/m2, Standard
500:1 Typ.
Contrast Ratio
Gray Scales
Up to 256 steps
Signal Input Connector
Video
HD15-15pin, Digital DVI, NTSC, S-Video
RS-232 DB-9 (Optional)
Touchscreen
Temperature Environment
Operating Temperature
Storage Temperature
Humidity
32° ~ 122°F (0° - 50°C)
-4° ~ 149°F (-20° - 65°C)
10 ~ 90%RH (without condensation)
Power Source
Display Monitor
AC-Adapter
DC 12V
AC100~240V 60W (Without option, Normal
Operation)
Regulations
Safety and EMC
UL/cUL, FCC, CE, TCO99, Energy Star, CB, MPR
II, ERG/GS.VCCI, UL2601-1, EN60601-1
Cabinet
Desktop Stand
17.5inch (W) x 17.8inch (H) x 9.5inch (D)
450mm (W) x 455mm (H) x 245mm (D)
Free Mount
17.5inch (W) x 14.25inch (H) x 3inch (D)
450mm (W) x 362mm (H) x 76mm (D)
Weight
Desktop Stand
Free Mount
Tilt Base
20.6 lb. (9.3Kg)
16 lb. (7.3Kg)
0° Down 28° Up
Touch Panel
Optional Module
* All contents are subject to change without notice.
* Touch Screen Model doesn’t include the Video-in (C-Video, S-Video) function.
* Surface Wave Touchscreen model -TEW and Resistive Touchscreen model -TE
28 User’s Guide
SPECIFICATION
AMM17TK
LCD Panel
Type
44.2cm/17.4-inch Color TFT Panel
Active Matrix
Resolution
Pixel Pitch
Display Color
Response Time
Color Tone
Color Filter
Face Finishing
Viewing Angle
Video
1280 dots x 1024 lines (Recommended)
0.27mm
16 million colors
25ms
Up to 256 tone
RGB vertical stripe type
Anti-Glare Hard Coated
160°H 160°V (CR>=10)
0.7Vp-p analog RGB & TMDS (PanelLink) Digital
165 MHz x 1
Input Signal
Sync
2.5~5.0Vp-p separated sync
Input Impedance (Analog)
Video - 75 Ohm
Sync - 1k Ohm
Composite Sync
Digital
C-Video, S-Video
3 channel TMDS receiver, single pixel 24 bit MSB-
aligned RGB TFT
Scanning Frequency
Horizontal
30~68kHz
Vertical
56~85Hz (UP to 85Hz at 1024 x 768 mode and up to
75Hz at 1280 x 1024)
Display Size
H x V
13.6" x 10.9" (345.0mm x 276.48mm)
Brightness, Contrast Radtio, Gray Scales
Brightness
220 cd/m2, Standard
400:1 Typ.
Contrast Ratio
Gray Scales
Up to 256 steps
Signal Input Connector
Video
HD15-15pin, Digital DVI, NTSC, S-Video
RS-232 DB-9 (Optional)
Touchscreen
Temperature Environment
Operating Temperature
Storage Temperature
Humidity
32° ~ 104°F (0° - 35°C)
-4° ~ 140°F (-20° - 60°C)
10 ~ 90%RH (without condensation)
Power Source
Display Monitor
AC-Adapter
DC 12V
AC100~240V 60W (Without option, Normal
Operation)
Regulations
Safety and EMC
UL/cUL, FCC, CE, TCO99, Energy Star, CB, MPR
II, ERG/GS.VCCI, UL2601-1, EN60601-1
Cabinet
Desktop Stand
17.5inch (W) x 17.8inch (H) x 9.5inch (D)
450mm (W) x 455mm (H) x 245mm (D)
Free Mount
17.5inch (W) x 14.25inch (H) x 3inch (D)
450mm (W) x 362mm (H) x 76mm (D)
Weight
Desktop Stand
Free Mount
Tilt Base
20.6 lb. (9.3Kg)
16 lb. (7.3Kg)
0° Down 28° Up
Touch Panel
Optional Module
* All contents are subject to change without notice.
* Touch Screen Model doesn’t include the Video-in (C-Video, S-Video) function.
* Surface Wave Touchscreen model -TEW and Resistive Touchscreen model -TE
AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 29
SPECIFICATION
AMM18TK
LCD Panel
Type
46cm/18.1-inch Color TFT Pane
Active Matrix
Resolution
Pixel Pitch
Display Color
Response Time
Color Tone
Color Filter
Face Finishing
Viewing Angle
Video
1280 dots x 1024 lines (Recommended)
0.28mm
16 million colors
40ms
Up to 256 tone
RGB vertical stripe type
Anti-Glare Hard Coated
160°H 160°V (CR>=10)
0.7Vp-p analog RGB & TMDS (PanelLink) Digital
165 MHz x 1
Input Signal
Sync
2.5~5.0Vp-p separated sync
Input Impedance (Analog)
Video - 75 Ohm
Sync - 1k Ohm
Composite Sync
Digital
C-Video, S-Video
3 channel TMDS receiver, single pixel 24 bit MSB-
aligned RGB TFT
Scanning Frequency
Horizontal
30~68kHz
Vertical
56~85Hz (UP to 85Hz at 1024 x 768 mode and up to
75Hz at 1280 x 1024)
Display Size
H x V
14.13" x 11.3" (359mm x 287mm)
Brightness, Contrast Radtio, Gray Scales
Brightness
200 cd/m2, Standard
250:1 Typ.
Contrast Ratio
Gray Scales
Up to 256 steps
Signal Input Connector
Video
DB9-15pin, Digital DVI, NTSC, S-Video
RS-232 DB-9 (Optional)
Touchscreen
Temperature Environment
Operating Temperature
Storage Temperature
Humidity
41° ~ 95°F (5° - 35°C)
-4° ~ 140°F (-20° - 60°C)
10 ~ 90%RH (without condensation)
Power Source
Display Monitor
AC-Adapter
DC 12V
AC100~240V 60W (Max.)
Regulations
Safety and EMC
UL/cUL, FCC, CE, TCO99, Energy Star, CB, MPR
II, ERG/GS.VCCI, UL2601-1, EN60601-1
Cabinet
Desktop Stand
Free Mount
Weight
17.5inch (W) x 17.8inch (H) x 9.5inch (D)
17.5inch (W) x 14.25inch (H) x 3inch (D)
Desktop Stand
Free Mount
Tilt Base
22.8 lb. (10.4Kg)
18.1 lb. (8.2Kg)
0° Down 28° Up
Touch Panel
Optional Module
* All contents are subject to change without notice.
* Touch Screen Model doesn’t include the Video-in (C-Video, S-Video) function.
* Surface Wave Touchscreen model -TEW and Resistive Touchscreen model -TE
30 User’s Guide
SPECIFICATION
AMM19TK
LCD Panel
Type
48cm/19-inch Color TFT Pane
Active Matrix
Resolution
Pixel Pitch
Display Color
Response Time
Color Tone
Color Filter
Face Finishing
Viewing Angle
Video
1280 dots x 1024 lines (Recommended)
0.294mm
16 million colors
25ms
Up to 256 tone
RGB vertical stripe type
Anti-Glare Hard Coated
170°H 170°V (CR>=10)
0.7Vp-p analog RGB & TMDS (PanelLink) Digital
165 MHz x 1
Input Signal
Sync
2.5~5.0Vp-p separated sync
Input Impedance (Analog)
Video - 75 Ohm
Sync - 1k Ohm
Composite Sync
Digital
C-Video, S-Video
3 channel TMDS receiver, single pixel 24 bit MSB-
aligned RGB TFT
Scanning Frequency
Horizontal
30~68kHz
Vertical
56~85Hz (UP to 85Hz at 1024 x 768 mode and up to
75Hz at 1280 x 1024)
Display Size
H x V
14.8" x 11.9" (376mm x 301mm)
Brightness, Contrast Radtio, Gray Scales
Brightness
250 cd/m2, Standard
500:1 Typ.
Contrast Ratio
Gray Scales
Up to 256 steps
Signal Input Connector
Video
HD15-15pin, Digital DVI, NTSC, S-Video
RS-232 DB-9 (Optional)
Touchscreen
Temperature Environment
Operating Temperature
Storage Temperature
Humidity
32° ~ 122°F (0° - 50°C)
-4° ~ 140°F (-20° - 60°C)
10 ~ 90%RH (without condensation)
Power Source
Display Monitor
AC-Adapter
DC 12V
AC100~240V 80W (Max.)
Regulations
Safety and EMC
UL/cUL, FCC, CE, Energy Star, CB, MPR II,
ERG/GS.VCCI, UL2601-1, EN60601-1
Cabinet
Desktop Stand
Free Mount
Weight
17.5inch (W) x 17.8inch (H) x 9.5inch (D)
17.5inch (W) x 14.25inch (H) x 3inch (D)
Desktop Stand
Free Mount
Tilt Base
19 lb. (8.6Kg)
16 lb. (7.3Kg)
0° Down 28° Up
Touch Panel
Optional Module
* All contents are subject to change without notice.
* Touch Screen Model doesn’t include the Video-in (C-Video, S-Video) function.
* Surface Wave Touchscreen model -TEW and Resistive Touchscreen model -TE
AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 31
SPECIFICATION
AMM19TK/HB
LCD Panel
Type
48cm/19-inch Color TFT Pane
Active Matrix
Resolution
1280 dots x 1024 lines (Recommended)
0.294mm
Pixel Pitch
Display Color
Response Time
Color Tone
Color Filter
Face Finishing
Viewing Angle
Video
16 million colors
25ms
Up to 256 tone
RGB vertical stripe type
Anti-Glare Hard Coated
170°H 170°V (CR>=10)
0.7Vp-p analog RGB & TMDS (PanelLink) Digital
165 MHz x 1
Input Signal
Sync
2.5~5.0Vp-p separated sync
Input Impedance (Analog)
Video - 75 Ohm
Sync - 1k Ohm
Composite Sync
Digital
C-Video, S-Video
3 channel TMDS receiver, single pixel 24 bit MSB-
aligned RGB TFT
Scanning Frequency
Horizontal
30~68kHz
Vertical
56~85Hz (UP to 85Hz at 1024 x 768 mode and up to
75Hz at 1280 x 1024)
Display Size
H x V
14.8" x 11.9" (376mm x 301mm)
Brightness, Contrast Radtio, Gray Scales
Brightness
450 cd/m2, Standard
600:1 Typ.
Contrast Ratio
Gray Scales
Up to 256 steps
Signal Input Connector
Video
HD15-15pin, Digital DVI, NTSC, S-Video
RS-232 DB-9 (Optional)
Touchscreen
Temperature Environment
Operating Temperature
Storage Temperature
Humidity
32° ~ 122°F (0° - 50°C)
-4° ~ 140°F (-20° - 60°C)
10 ~ 90%RH (without condensation)
Power Source
Display Monitor
AC-Adapter
DC 12V
AC100~240V 80W (Max.)
Regulations
Safety and EMC
UL/cUL, FCC, CE, Energy Star, CB, MPR II,
ERG/GS.VCCI, UL2601-1, EN60601-1
Cabinet
Desktop Stand
Free Mount
Weight
17.5inch (W) x 17.8inch (H) x 9.5inch (D)
17.5inch (W) x 14.25inch (H) x 3inch (D)
Desktop Stand
Free Mount
Tilt Base
19 lb. (8.6Kg)
16 lb. (7.3Kg)
0° Down 28° Up
Touch Panel
Optional Module
* All contents are subject to change without notice.
* Touch Screen Model doesn’t include the Video-in (C-Video, S-Video) function.
* Surface Wave Touchscreen model -TEW and Resistive Touchscreen model -TE
32 User’s Guide
Connectors
DC Input
Connector Jack Power Input
The SCD-014-1-A (SHIUA CHYUAN) or equivalent.
Pin Description
1 +12V DC
2 GND
VideoInput
15 pin D-subminiature connector.
The vedor P/N is DHSB-15 FRF7(LEOCO) or equivalent.
D
e s c r i p t io n
P in
D
e s c r i p t io n
P in
9
R e d V id e o
G r e e n V id e o
B lu e V id e o
1
N
C
2
3
4
5
6
7
8
V G A
C
o n
1 0
1 1
1 2
1 3
1 4
1 5
N
C
N
C
S D A ( D D C 1 /2 )
H - s y n c
L o g ic G r o u n d
R e d V id e o G r o u n d
G r e e n V id e o G r o u n d
B lu e V id e o G r o u n d
V - s y n c
S C
L
( D D C 2 B )
24 pin DVI-D connector.
DDWG or equivalent connector.
P in
S ig na l A s s ig nm e nt
T.M .D .S . D a ta 2 -
T.M .D .S . D a ta 2 +
P in
9
S ig na l A s s ig nm e nt
T.M .D .S . D ata 1 -
T.M .D .S . D ata 1 +
P in
1 7
S ig na l A s s ig nm e nt
T.M .D .S . D ata0 -
T.M .D .S . D ata0 +
1
2
3
1 0
11
1 8
T.M .D .S . D a ta 2 /4
S hield
T.M .D .S . D ata 1 /3
S hield
1 9
T.M .D .S . D ata0 /5
S hie ld
4
5
6
T.M .D .S . D a ta 4 -
T.M .D .S . D a ta 4 +
D D C C lo c k
1 2
1 3
1 4
T.M .D .S . D ata 3 -
T.M .D .S . D ata 3 +
+ 5 V P o w e r
2 0
2 2
2 2
T.M .D .S . D ata5 -
T.M .D .S . D ata5 +
T.M .D .S . C lo ck
S hie ld
7
8
D D C D a ta
1 5
1 6
G ro und (fo r + 5 V )
H o t P lug D etec t
2 3
2 4
T.M .D .S . C lo ck +
T.M .D .S . C lo ck -
N o C o nnec t
Touch Port
9Pin D-subminiature connector.
D
D
R
T
e
C
X
X
T
s
c
r i p t i o
n
P
1
i n
D
D
R
C
R
e
s
c
r i p t i o
n
P
i n
D
S
R
6
D
D
R
2
T
S
7
3
T
S
8
D
4
I N
C
9
L
o
g
i c
5
G
r o
u
n
d
AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 33
Description of Warranty
Advan warrants that the goods the goods sold hereunder will be free of defects in materials
and workmanship, and such goods will substantially conform to the specifications furnished
by Advan, and to any drawings or specifications furnished to Advan by the Buyer if
approved by Advan. This warranty shall be effective only if Advan receives notice of such
defect or nonconformance during the period of the warranty. Advan sole and exclusive the
Advan product(s) with refurbished units provide a credit to buyer in the amount of the
purchase
price.
Commencement and Duration of Warranty
The warranty period begins on the date of shipment from Advan. The goods sold hereunder
are warranted for a period of three years (36 months) from date of shipment unless otherwise
agreed to by Buyer and Advan. No extension of the warranty will be given during the time
the goods are in Advan possession.
Place of Repair or Replacement
In order to obtain service under this warranty, Buyer must notify Advan of the defect before
expiration on the warranty period, and request a “Return MaterialAuthorization Number.” If
the configuration has been modified in any manner, the product must be returned to its
original configuration before any warranty service will be perfomed by Advan. No goods are
to be returned to Advan without prior authorization. Buyer will be responsible for packaging
and shipping the defective goods to the Advan Service Facility with shipping charges
prepaid.
Limitation of Warranty
Monitor:
For one years (12 months) after the date of purchase,ADVAN or itsAuthorized Service Centers,
will repair or replace if defective in material or workmanship. This Limited Warranty does not
include cleaning, or damage caused by accident, neglect, misuse or improper installation or
operation, any damage caused from service, maintenance, modifications or tampering by anyone
other than anADVANAuthorized Service Representative, or by the use of supplies, consumable
items and conditions beyond the control ofADVAN, such as common carrier provided equipment
and/or facilities, operation ofADVAN product in excess of the specifications or with the Serial
Number or Rating label removed.
*Touch Screen:
For one year after the date of purchase, ADVAN or itsAuthorized Service Centers, will repair
or replace if defective in material or workmanship. This Limited Warranty does not include
cleaning, or damage caused by accident, neglect, misuse or improper installation or opera-
tion, any damage caused from service, maintenance, modifications or tampering by anyone
other than an ADVAN Authorized Service Representative, or by the use of supplies, consum-
able items and conditions beyond the control of ADVAN, such as common carrier provided
equipment and/or facilities, operation of ADVAN product in excess of the specifications or
with the Serial Number or Rating label removed.
34 User’s Guide
ADVAN DISCLAIMSALLOTHERWARRANTIES EXPRESS OR IMPLIED INCLUDING,
WITHOUT LIMITATION,ANYIMPLIED WARRANTIES OF MERCHANTABILITYOR
FITNESS FOR PARTICULAR PURPOSE, EXCEPTTO THE EXTENTTHATANYWARRAN-
TIES IMPLIED BYLAWCANNOTBEVALIDLYWAIVED.
No oral or written information or advice given byADVAN, its authorized service center,
distributors, dealers, agents or employees, shall create another warranty or modify this
warranty. This warranty states ADVAN’s entire liability and your exclusive remedy against
ADVAN for any failure of theADVAN’s product to operate properly.
Neither ADVAN nor anyone else involved in the development, production, or delivery of this
product shall be liable for any indirect, incidental, special consequential, exemplary, or
punitive damages, including lost profits, arising from the use of or inability to consequential
or incidental damages, the above limitation may not apply to you.
This Limited Warranty gives you special legal rights and you may also have other right,
which vary from State to State.
Installation
Advan makes no warranty with respect to any installation of Advan’s product(s)
by Advan, any authorized dealer, or any other person.
Technical Assistance
For technical assistance please call (510)490-1005 between 8:00 a.m. and 5:00 p.m. PST,
Monday through Friday or email to [email protected] with a description of your
technical issues.
Service
If your Medical Monitor needs service, call Advan Customer Service at
(510)490-1005 between 7:00 a.m and 4:00 p.m PST, Monday through
Friday or fax to (510)490-1151. You will need the unit’s serial number and a
brief description of the problem and where unit were purchased to receive a RMA number.
If a service is required please return the product for service using the original shipping
container with the RMA number included in package on the outside of the box.
In order to protectADVAN employees form potential health hazards,ADVAN requires that
the RMAproduct be disinfected before returning toADVAN forservice.Any product not
cleaned prior to shipment will be returned to the customer.
Note: Returns will not be accepted without an assigned RMA number.
In-transit damage is not covered by warranty. We suggest you always insure your shipment.
Advan will only pay for the return shipment by surface transportation. It is the responsibility
of the sender to prepay transportation charges.
AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 35
Tounchscreen User's Manual (AMM17TK-TE/AMM18TK-TE/
AMM19TE orAMM17TK-TEW/AMM18TK-TEW/AMM19TK-TEW)
Quick Start
1.Connect Power Code and VGACable of LCD Monitor.
2.Connect Touchscreen DB9 male RS-232 cable.
3.Turn the LCD display Power ON.
4.Adjust the tilt of LCD Monitor.
5.Adjust the Picture of LCD Monitor.
6.Install driver software of Touchscreen (See "Driver software" for details).
7.Adjust the calibration of Touchscreen (See "Driver software" for details).
Introduction
The ELO IntelliTouch Touchscreen system consists of a touchscreen and an
electronic touchscreen controller. The touchscreen may be a flat, spherical, or
cylindrical and is installed over the face of the LCD. The touchscreen controller
installed inside of theLCD.
The IntelliTouch Touchscreen
The IntelliTouch surface wave touchscreen consists of a glass panel molded to the
precise shape of a display's face.Ascratch-resistant, hard-coated plastic cover
sheet may be clear for best image clarity or have an antiglare finish.
The IntelliTouch Controller
The IntelliTouch controllers provide the drive signal for touchscreen, convert the
received analogue signals into digital touch coordinates, and send these
coordinates to the computer.
36 User’s Guide
Touchmonitorinstallation
Cable Connection
1. Connect and test LCD as a video display only.
2. Plug the DB9 male into the DB9 female connector labled "TOUCHSCREEN"
on the back of the LCD Monitor.
Driver software
ELO provide driver programs for the DOS, Windows 3.1, Windows 95/98,
Windows NT, Windows 2000, Windows XP, OS/2, and Macintosh systems.
Additional drivers may be available for other system. Contact ELO for details.
Installing Driver software forWindows /Windows NT
1. Shutdown Windows or Windows NT and turn off your computer.
2. Install touchscreen hardware as described in the "Quick start" or "Touchmonitor
installation".
3. Start your computer.
4. Insert the Windows or Windows NT driver disk into diverAor B.
5. Browse for "setup.exe" in the directory to which you extracted the driver files.
6. Type "setup.exe" in the space provided and press Enter.
7. The touchscreen setup wizard will appear. You will need to select serial port,
type of touchscreen controller, and language.
8. Complete the setup program.
9. Shutdown and restart windows NT.
10. Click the start button, then click control panel.
11. Double-click touchscreen control panel.
12. Click the calibrate button and touch each of the three targets as they appear
on the screen.
Contacting ELO
ELO Touchsystems INC.
6500 Kaiser Drive Fremont,
CA 94554 USA
AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 37
|