3
Owners handbook
and
Installation instructions
A S T O R I A 3
Contents
Page
Lighting the cooker
4
The grill
6
8
The hotplate
The oven
11
13
14
17
20
23
25
27
29
30
31
32
33
35
Blank page
Oven cooking chart
Slow cooking
Care and cleaning
Installing the cooker
General information
What is wrong and why?
Servicing
Installation Instructions
Technical Data
Safety requirements/ventilation
Location of appliance/installation
Testing
3
A S T O R I A 3
Lighting the cooker
The ignition system works by means of a battery. Details on how to
replace the battery are given on page 27.
Grill and hotplate
To light
1 Push in the control knob and turn to the large flame symbol (highest
setting), and press the ignition button immediately. When the burner
has lit release the button.
Warning: If the ignition button is not pressed immediately a build up of
gas may cause the flame to spread.
Oven
To light:
1 Open the oven door.
2 Push in the control knob and turn it to the large flame symbol
(highest setting) and press the ignition button immediately. When the
burner has lit release the button. There will only be small flames at first.
3 Now turn the control knob to the gas
mark you want.
4
Wait until the burner is showing large
flames.
5 Close the oven door.
To turn off any burner
4
A S T O R I A 3
1 Push in the control knob and turn it to the off position. This is shown
by a large dot.
For your safety
When you are lighting any burner check that it has lit before you
leave the cooker.
When you are turning off a burner, do not leave the cooker
until the flame has gone out.
5
A S T O R I A 3
The grill
The grill is a high-speed grill. The instructions below tell you how to vary
the heat setting and how to change the height of the grid to suit the food
you are cooking. You should remember to turn the food regularly.
You should not use the grill to keep food warm as it will continue to
cook the food.
Heat control
The grill control gives two heat settings.
The control knob turns to the left from
'OFF' to 'HIGH' and then to 'LOW'. The high
setting should be used for fast cooking such
as toast. Use the low setting to cook thicker
food such as chicken after it has been
browned on the high setting.
Cooking positions
Place the grill pan so that the bottom of the
handle fits into the hole on the shelf.
Most food should be cooked on the grid
in the grill pan. The grid can be turned over
to suit different thicknesses of food.
You can place some dishes straight on to
the grill shelf. This is useful when you are
browning the top of food such as cauliflower
cheese.
6
A S T O R I A 3
Preheating
You don't usually need to preheat the grill. You may wish to preheat it
for a couple of minutes when you are cooking steak or when browning
food.
Positioning food on the grid
Place food such as toast, teacakes and
muffins towards the centre of the grid.
Place food which needs a more gentle heat
such as tomatoes and mushrooms towards
the edge of the grid.
Arrange meat, meat products and fish to
suit their thickness and how you like them
cooked.
7
A S T O R I A 3
The hotplate
Heat control
The hotplate control knobs turn to the left
from 'OFF' to 'HIGH' and then to 'LOW'. You
can adjust the heat by turning the control
between the highest and lowest settings.
These are shown as a large and a small
flame symbol.
Burner sizes
The hotplate has three burner sizes to suit
different types of cooking:
Largest burner (Rapid) - use a large pan for
food such as chips.
Medium burners (Normal) - use for everyday
cooking.
Small burner (Simmer) - use for simmering
food such as soups and stews.
The largest pan which you should use on any burner is 230mm (9").
The base of the smallest pan should not measure less than 100mm (4").
8
A S T O R I A 3
For your safety
1
2
3
Take care to avoid burns and scalds when you
are reaching across the hotplate.
Use pans with flat bases. They are more stable
than pans which are warped.
Do not use pans with very heavy handles which
cause the pan to tip.
4
5
Put pans on the centre of the burners.
Position pan handles so they cannot be
accidentally knocked.
6
Take extra care when you are deep fat frying. Do
not cover the pan with a lid.
Do not leave a pan unattended. If the pan
catches fire, leave it where it is and turn off all
controls.
Place a damp cloth or a fitting lid over the pan to
smother the flames.
Never put water on the fire.
Leave the pan to cool for 30 minutes.
7
If you are using a Wok we recommend it has a flat
base as it will stand stable on the pan supports. If
you use a round based Wok with a collar support,
the collar must be of the open wire work type. A
closed collar will affect the performance of the
burner. Before you use the Wok make sure that
the collar is stable on the pan supports. Always
follow the instructions that come with the Wok.
9
A S T O R I A 3
Helpful hints
1
Keep flames under the base of
pans. If the flames lick round the
sides of the pans you are wasting
gas.
2
3
Only heat the amount of liquid you
need. Do not overfill pans.
Cover pans with a lid whenever
possible. The food will heat up
more quickly and there will be less
steam in the kitchen.
4
5
6
Try cooking more than one
vegetable in the same pan, for
example potatoes and carrots.
Cut vegetables into smaller pieces.
This way they will cook more
quickly.
A pressure cooker will save time
and energy.
10
A S T O R I A 3
The oven
Before you use the oven you should wipe it out with a damp cloth to
remove any dust.
Heat zones
There are zones of heat within the oven.
The temperature in the middle is the gas
mark you have chosen. The top of the
oven is slightly hotter and the lower shelf
slightly cooler. The base of the oven is
quite a lot cooler. You can make use of
these heat zones when you are cooking
foods requiring different temperatures all at
the same time.
If you are cooking more than one tray of similar items, for example
cakes or biscuits, swap the trays during cooking or you can remove the
top tray when the food is cooked and move the lower tray to the higher
shelf to finish cooking.
Preheating
You do not need to preheat the oven when casseroling and so on.
Preheat the oven for baking or when you are cooking sensitive food
such as Yorkshire puddings, soufflés and yeast mixtures.
When you are cooking or reheating frozen or chilled food read the
instructions on the packing.
When you need to preheat the oven, we recommend you do so for
20 minutes.
Oven Shelves
You can slot the oven shelves in any of five
positions. Positions are counted from the top
downwards.
For safety the shelf will only pull out so
far. If you want to remove a shelf completely
pull it forward as far as it will go, raise the
front edge and lift it out. To put the shelf into
a different position keep the front edge
raised, slot the shelf on to the runner, lower
the front edge and slide the shelf in.
11
A S T O R I A 3
Baking trays and dishes
For your safety
Never place cooking dishes, trays
and so on over the oven burner.
This will damage the cooker as
well as the ovenware and possibly
the floor covering underneath the
cooker.
Leave a gap of 13mm (½") between
all dishes and the sides of the oven
so the heat can circulate properly.
Do not push dishes too far back as
food will burn if it overhangs the
burner flames.
For the best results we recommend that you use a baking tray which is
310mm (12") square. If you use a tray or tin which is larger than this,
you may need to turn it around during cooking.
Place single dishes on the centre of the shelf. You may need to turn
large items around during cooking.
Condensation
Condensation may form on the cooker. This is quite normal and nothing
to worry about. The condensation forms when heat and moisture are
present, for example during cooking. Whenever possible try to make
sure that food which contains a lot of moisture for example casseroles
are covered. If you do notice any condensation, wipe it up straight
away.
12
A S T O R I A 3
This page has been intentionally left blank.
13
Oven cooking chart
These instructions are for cooking in the oven after it has been pre-heated for 20 minutes.
If you are cooking more than one tray of similar items, for example cakes or biscuits, swap the trays around during cooking or you
can take the top tray out of the oven when the food is cooked and move the lower tray to the higher shelf to finish cooking.
Always leave at least one shelf position between shelves to allow heat to circulate.
The recommended shelf positions give the best results.
Put the dishes in the centre of the shelf.
You can change the gas marks and cooking times to suit your own tastes.
It is important to check that food is piping hot before serving.
Gas
mark
Shelf
position
Approximate
cooking time
Food
Roasting meat:
Beef
5
4
Rare:
Medium:
Well Done:
20 mins. per ½kg (1lb) and 30 mins.
25 mins. per ½kg (1lb) and 25 mins.
30 mins. per ½kg (1lb) and 30 mins.
Lamb
5
5
4
4
Medium:
Well Done:
25 mins. per ½kg (1lb) and 25 mins.
30 mins. per ½kg (1lb) and 30 mins.
Pork and Veal
Medium:
Well Done:
30 mins. per ½kg (1lb) and 30 mins.
35 mins. per ½kg (1lb) and 35 mins.
Thoroughly thaw frozen joints before cooking them.
Gas
Shelf
Approximate
Food
mark
position cooking time
Poultry:
Chicken
5
4
4
5
4
4
20 mins. per ½ kg (1lb) and 20 mins.
Turkey below 4.5kg (10lbs)
over 4.5kg (10 lbs)
Duck and duckling
25 mins. per ½ kg (1lb) and 25 mins.
15 mins. per ½ kg (1lb) and 15 mins.
25 mins. per ½ kg (1lb)
4 or 5
4
Stuffed poultry
Cook as above but calculate weight including stuffing.
Thoroughly thaw frozen joints before cooking them.
The times given above are for when you are open roasting. If you cover the food with foil or a lid you should allow an extra 5
minutes cooking time for each ½ kg (1lb).
Yorkshire pudding - large
- individual
7
7
2
2
25 - 30 mins.
15 - 25 mins.
Cakes:
Christmas cake (8")
Rich fruit 180mm (7")
205mm (8")
Madeira, 180mm (7")
Small cakes
2
2
2
4
5
7
4
4
4
4
4-5 hours
2¼-2¾ hours
2½-2¾ hours
1 hour
15-25 mins.
10-20 mins.
1 & 3
1 & 3
Scones
Victoria sandwich
180mm (7")
205mm (8")
4
4
2 & 4
2 & 4
20-30 mins.
20-35 mins.
Gas
mark
Shelf
position
Approximate
cooking time
Food
Pastries:
Plate tart (shortcrust)
Fruit pie (shortcrust)
Mince pies (flan pastry)
6
6
5
1
1
25-35 mins.
25-35 mins.
15-25 mins.
1 & 3
To help pastry brown on the underside cook on a metal plate, or if plates are flat and have no rim underneath, place on baking tray
to cook.
Puddings:
Milk puddings
Baked sponge pudding
Baked custards
2
4
3
3
4
4
2 hrs.
45-60 mins.
50-60 mins.
Yeast Mixtures:
Bread 0.45kg (1lb loaves)
0.90kg (2lb loaves)
Rolls and buns
8 *
8 *
8 *
3
3
2
30-40 mins.
30-40 mins.
10-20 mins.
* When baking bread cook at Gas mark 8 for 10 minutes before reducing to Gas mark 6 for the remainder of the cook time.
Note: You must soak dried beans then boil them in an open pan for 15 minutes before you add them to any dish.
A S T O R I A 3
Slow cooking
The slow cook setting gives a very low heat in the oven. It is particularly
useful when you are cooking soups, stews and casseroles because
the long slow cooking will make cheaper, tougher cuts of meat more
tender.
You need to cook food at gas mark 6 for 30 minutes before you turn the
oven down to the slow cook setting. This makes sure that the
temperature of the food gets hot enough to start the food cooking.
Some foods such as pastry and biscuits are not suitable for slow
cooking because the temperature is too low.
Cover all food during cooking to prevent it from drying out. You can
uncover food for the last half hour if it is normally served golden brown.
Food preparation - slow cooking
Joints of meat and poultry
Do not cook meat joints over 2.7kg (6lb).
Do not cook poultry over 2kg (4lb 8oz).
Cook on the middle shelf of the oven or above.
Cook stuffing separately.
Cook for at least 6 hours.
Only cook joints of pork if you can make sure, by using a meat
thermometer, that the temperature inside the joint is at least 88o C.
For good air circulation always stand joints on a rack in the roasting
tin or casserole.
Thaw all frozen meat and poultry before you cook it.
Prime cuts of meat do not benefit from slow cooking.
Cut off unwanted fat and skin unless it is browned first.
Cook for 30 minutes at gas mark 6, then reduce to the slow cook
setting.
17
A S T O R I A 3
Soups, casseroles and stews
Do not cook casseroles over 3 kg (6lb).
Bring to the boil on the hotplate then cook on slow cook.
Cook in the middle of the oven or above.
Vegetables
Cut into small pieces.
Dried beans must be pre-soaked then boiled in an open pan for 15
minutes before adding to any dish.
Place vegetables under meat in casseroles.
Cook for 30 minutes at gas mark 6, then reduce to the slow cook
setting.
Milk puddings
Cover the cereal with boiling water and leave it to stand for 30
minutes.
Drain and make the pudding in the usual way.
Cook for 30 minutes at gas mark 6, then reduce to the slow cook
setting.
General points for slow cooking
Frozen foods
Thaw thoroughly before cooking.
Thickening
Toss meat in flour for casseroles. Blend cornflour with water and add it
at the end of cooking.
Flavouring
Flavours are held in the food because there is little evaporation. Adjust
flavouring at the end of the cooking time.
Liquid
Use slightly less liquid as there is little evaporation during cooking.
Milk and milk products, for example cream
Add these towards the end of cooking to prevent them from curdling.
18
A S T O R I A 3
Reheating
Cool left over food quickly and then put it in the fridge. Do not reheat
food using the slow cook setting. Reheat food in the usual way or in a
microwave.
Only reheat food once.
19
A S T O R I A 3
Care and cleaning
For your safety
For hygiene and safety reasons you must keep this gas cooker
clean. A build up of fat or other foodstuff could cause a fire.
Try to mop up spills and splashes as soon as they happen. But
be careful as parts of the appliance will be hot.
Do not use any polishes, caustic cleaners, abrasives, washing soda
or soap powder except those recommended
in this booklet.
Please note: If we recommend you use hot
soapy water we mean hot water with
washing up liquid in it and not any other
cleaning product.
If you own a dishwasher please read the
operating instructions for the machine before
you wash any part of your cooker.
Clean your cooker regularly using a cloth that has been wrung out in
hot soapy water. Rinse and polish it dry using a soft cloth.
When you remove parts of your cooker for cleaning do not plunge
them into water whilst they are very hot as this may damage the finish of
the parts.
The hotplate
Clean the hotplate top using a mild abrasive such as 'Jif'. Take care not
to damage the spark electrodes. If the spark electrodes are damaged
the burners will not light.
You can remove the pan supports, burner caps and burner crowns
to clean them. Again take care not to damage the spark electrodes.
If any food spills do occur during cooking you can place the pan on
another burner to finish cooking. Then you can remove the dirty parts
and clean them before the spill 'burns on'.
20
A S T O R I A 3
You can wash the removable parts in very hot soapy water. You may
use mild abrasives. Make sure that the electrode and the hole and slots
in the crown are not blocked with food or cleaning materials.
Clean the burner crowns by soaking them in very hot soapy water.
You can remove any stubborn stains by scouring with a soap filled pad
such as 'Brillo'. If you look after the burner crowns in this way they will
stay reasonably clean. However the surface will dull with time.
Aluminium based saucepans can leave shiny metal marks on the
pan supports. Clean the pan supports regularly to remove the marks
using a mild abrasive like 'Jif' with a soft scourer. For more stubborn
marks you can use a soap filled pad such as 'Brillo'.
After cleaning the cooker parts, dry them
thoroughly before you put them back.
When replacing hotplate burner parts
1. Crown to body (Do not try to force the crown on to the body). Make
sure that the hole in the crown is centrally over the electrode.
Check that the two longer location pegs
sit in the slots in the body. When the
crown is in the position let it fall freely on
to the body.
Check that the crown can be moved
slightly from side to side.
2. Cap to crown
Place cap centrally on the top of crown
(enamel side up). Move sideways and
front to back to check the cap is fitted
properly.
3. Check for ignition
If a burner will not light then you need to
check the crown and cap positions.
The grill
Clean the area around the grill frequently using hot soapy water.
After use you can soak the pan for a few minutes and then clean it
using mild abrasives or a soap filled pad such as 'Brillo'.
21
A S T O R I A 3
Clean the grill shelf using hot soapy water. Mild abrasives can be
used if necessary.
If the grill shelf is removed it must be replaced the right way up.
The oven
The inside of the oven is finished in vitreous enamel. You should clean
the oven regularly using hot soapy water and mild abrasives or a soap
filled pad such as 'Brillo'. If you use any oven cleaners they must have
the Vitreous Enamel Development Council (VEDC) seal of approval.
Follow the instructions on the cleaning agent and protect the oven
burner with aluminium foil to prevent it becoming blocked.
General
Clean the oven shelves and the oven door while they are still slightly
warm. This way you can easily remove any splashes and spills. Wipe
with a cloth that has been wrung out in hot soapy water. You may use
mild abrasives.
22
A S T O R I A 3
Installing the cooker
For your safety
This cooker must be installed and serviced by a competent
person as stated in the Gas Safety (Installation & Use)
regulations current editions.
It is important that the cooker is suitable for your gas supply.
Your installer should check the data badge.
Ensure that a stability bracket is fitted.
Location
For your safety
The use of a gas cooking appliance results in the production of
heat and moisture in the room in which it is installed. Ensure that
the kitchen is well ventilated: keep natural ventilation holes open
or install a mechanical ventilation device (mechanical extractor
hood).
Prolonged intensive use of the appliance may call for additional
ventilation, for example opening of a window, or more effective
ventilation, for example increasing the level of mechanical
ventilation where present.
For further details see page 32.
23
A S T O R I A 3
Positioning
The diagram shows how close to the cooker cupboards, shelves,
curtains and so on can be fitted. Refer to the diagram and carefully read
the instructions to make sure your cooker is fitted safely. If you are in
doubt your installer will give you advice.
Do not fit any materials which may catch fire for example wood or
curtains behind the cooker.
Base units which are higher than the hotplate must be 100mm away.
If a cooker hood is fitted refer to the cooker hood installation
instructions.
We recommend that cabinets fitted next to or above the cooker
meet British Standards. Your installer will give you advice if you are
not sure.
Cooker dimensions
Overall height:
1460mm
Height to hotplate:
902mm - 920mm
(adjusted by four screw feet)
498mm
Width:
Depth:
600mm (to front of door panel)
24
A S T O R I A 3
General information
For your safety
Do not block any of the cooker vents.
Never line any part of the cooker with aluminium foil.
Don't let items which can catch fire or electric mains leads such as
kettle flexes trail over any part of the cooker.
Moving your cooker
You may damage some soft or badly fitted floor coverings when you
move the cooker. The floor covering under the cooker should be
securely fixed so it does not ruck up when you move the cooker across
it. Alternatively you could remove the floor covering.
To move the cooker open the oven door. Raise the cooker off its
front feet by lifting from inside the oven. Pull the cooker forward. When
you replace the cooker push it back to the stop and make sure there is
the same gap at each rear corner.
The battery
The battery for the ignition will usually last for
many months. If the ignition system doesn't
work you probably need to replace the
battery.
The battery holder is located at the front
of the bottom storage compartment.
Replace the battery as shown in the
diagram. Use one AA size battery.
You can light the burners with a match
until you have time to change the battery.
25
A S T O R I A 3
Storage
The compartment below the oven is useful for storing baking trays, cake
tins and so on. Do not store anything in this compartment which may
catch fire.
Reversing the oven door
You can turn the oven door around so that it opens on the other side.
Your supplier can arrange this.
26
A S T O R I A 3
What is wrong and why?
We strongly recommend that you carry out the following checks on your
cooker before calling a Service Engineer.
Problem
The oven, grill or hotplate will not light.
Check
If you cannot hear any sparking or the sparking is slow when you
press the ignition button it may not be strong enough to light the
cooker. You will probably need to replace the battery. For
instructions on how to do this see page 25. You can light the
burners with a match until you have time to change the battery.
Check that there is not a problem with your gas supply. You can do
this by making sure that other gas appliances such as your central
heating or gas fire are working.
If only the hotplate burners will not light, make sure that the burner
parts have been replaced properly. See instructions on page 21.
Problem
Food is cooking too quickly or too slowly.
Check
Check that you are using the recommended gas marks and shelf
positions. See page 14. Be prepared to adjust the gas mark up or
down to achieve the results you want.
Problem
The oven is not cooking evenly.
Check
Check that the cooker is installed properly and is level.
Check that you are using the recommended temperatures and shelf
positions.
If you are using a tin or tray which is larger than the one we
recommend, be prepared to turn it round during cooking.
If you are cooking a large item be prepared to turn it round during
cooking.
27
A S T O R I A 3
Problem
Having difficulty cleaning any part of the cooker.
Check
Check that you are following the instructions for care and cleaning
(see page 20).
28
A S T O R I A 3
Servicing
For your safety
Maintenance work must only be done by a competent person.
Do not try to repair the cooker yourself. This could be
dangerous.
It is dangerous to alter or modify the product in any way.
Before you call a service engineer check through the 'What is wrong
and why?' information on pages 27 and 28. If you still feel there is a
problem you should contact the place you bought the cooker from. They
will arrange for it to be serviced.
You can get service and spares from your supplier and not direct
from our factory. If you don't use manufacturers original spares the
B.S.I. approval of your cooker may not be valid.
When you report a problem to your supplier try to describe the
nature of the fault. Always give your cookers full name and serial
number which you can see on the left hand side of the storage
compartment.
Make a note of this information in this space:
Name:
Serial Number:
The Gas Consumers' Council
The Gas Consumers' Council (GCC) is an independent organisation
which protects the interests of gas users. If you need advice, you will
find the telephone number in your local telephone directory under Gas.
29
INSTALLATION INSTRUCTIONS
Serial number in storage
compartment. Data badge on
top rear of panel.
For your safety
Natural Gas and L.P. Gas versions of this appliance are available.
Check that this model is suitable for the type of supply available.
In the interest of safety this appliance must be installed and/or
serviced by a competent person, as stated in the Gas Safety
(Installation and Use) Regulations Current Editions.
30
A S T O R I A 3
TECHNICAL DATA
DIMENSIONS
Height
1462mm (nominal)
Width
500mm (nominal)
Depth
600mm
Overall
(from elbow
to front of door panel)
Height to hotplate
907mm nominal -
see important note 'Location of the Appliance' (see Page 33).
Space for fixing at hotplate level
2mm minimum
clearance
600mm
Nominal
Space for fixing above hotplate level 100mm each side
of appliance
Minimum space above grill
Minimum distance from rear wall
Weight of appliance
500mm
50.0kg
20mm
CONNECTIONS
Gas
Rear left hand side of appliance at hotplate level
Rc½ (½" B.S.P. female)
None
Electric
IGNITION
Spark Generator
Battery
APCO 6BG6893
1.5 volt AA size
GRILL
Heat Input
Natural Gas
3.3kW (11263 Btu/h) 3.55kW (255g/h)
L.P. Gas
Injector Marking
138
95
31
A S T O R I A 3
HOTPLATE
Natural Gas
R.H.F.
1.0kW
R.H.R.
2.0kW
L.H.R.
2.0kW
L.H.F
2.8kW
Heat Input
(3412 Btu/h)
079
(6824 Btu/h)
104
(6824 Btu/h)
104
(9554 Btu/h)
130
Injector Marking
L. P. Gas
R.H.F.
1.0kW
(71.8g/h)
51
R.H.R.
2.0kW
(143.7 g/h)
72
L.H.R.
2.0kW
(143.7 g/h)
72
L.H.F.
2.7kW
(194 g/h)
83
Heat Input
Injector Marking
OVEN
Natural Gas
2.4kW (8189 Btu/h)
108
Diamond 'H' GSD 100/28
Diamond 'H' 1100-94/B2
69
L P. Gas
2.4kW (172.4g/h)
78
Diamond 'H' GSD 100-30
Diamond 'H' 1100 99/B2
78
Heat Input
Injector Marking
Flame Supervision Device
Thermostat
Thermostat By-pass Marking
GENERAL
Ignition
Spark Gap
H.T. Spark
3-4mm
H.T. Spark
3-4mm
IMPORTANT - SAFETY REQUIREMENTS
This appliance must be installed in accordance with the Gas Safety (Installation and Use) Regulations
Current Editions. Detailed recommendations are contained in the following British Standard Codes of Practice
- BS.6172, BS.5440: Part 2 and BS.6891. All British Standards must be 'Current Editions'.
PROVISION FOR VENTILATION
This appliance is not connected to a combustion products evacuation device. It shall be installed and
connected in accordance with the current installation regulations. Particular attention shall be given to the
relevant requirements regarding ventilation.
The room containing the appliance should have an air supply in accordance with BS. 5440: Part 2 Current
Edition. All rooms require an openable window or equivalent and some rooms will require a permanent vent
as well. For room volumes up to 5m³ an air vent of 100cm² is required: for room volumes between 5m³ and
10m³ an air vent of 50cm² is required. If the room has a door that opens directly to the outside, no air vent is
required. For room volumes that exceed 11m³ no air vent is required. If there are other fuel burning
appliances in the same room, BS.5440: Part 2 Current Edition should be consulted to determine the requisite
air vent requirements.
Prolonged intensive use of the appliance may call for additional ventilation, for example opening a window, or
more effective ventilation, for example increasing the level of mechanical ventilation where present.
32
A S T O R I A 3
LOCATION OF APPLIANCE
This appliance must not be installed in a bed-sitting room of volume less than 20m³ or in a bathroom or
shower room. It is essential that the appliance is positioned as stated below. The appliance must be a
minimum of 20mm from the rear wall (note that this dimension is provided by the inlet elbow). Shelves, wall
cabinets and cooker hoods must not be fitted closer that 500mm to the top of the grill canopy or within 100mm
of the sides of the grill. Curtains must not be fitted immediately behind the appliance or within 200mm of the
sides of the grill. If fitted next to or between two base units a minimum space of 1mm must be left between
the units and the sides of the appliance. The hotplate must be set to a minimum of 7mm above the adjacent
units (note that the levelling feet fitted to the appliance will achieve a nominal height to hotplate level of
907mm -5+13mm). Base units not meeting the above conditions must be a minimum of 100mm away from the
hotplate. L.P.G. cookers MUST NOT be installed below ground level, i.e. in a basement.
INSTALLATION
1. PARTS REQUIRED
The loose hotplate parts are packed in the polystyrene fitment on
the top of the hotplate. The grill pan, grill pan handle, fixing screws
and splashplate fixing screws can be found in the furniture pack
which is located in the bottom compartment. The grill pan requires
assembly before use (see Fig. 1).
2. GRILL ASSEMBLY
The two splashplate screws should be screwed into the back of
the appliance about halfway in (see Fig. 1a). Engage the keyhole
slots in the splashback behind the two screws taking care not to
trap the H.T. wire (see Fig. 1b).
Tighten 6 of splashplate screws (see Fig.1c).
Connect the grill supply union at the back of the appliance and pull
the grill H.T. lead through the opening in the splashplate and
connect on to the spark generator.
Fig.1
Grill Pan Handle Assembly:
Assemble grill pan (see Fig.1)
and secure two screws provided.
Fig.1a
Fig.1c
Fig.1b
33
A S T O R I A 3
3. LEVELLING THE APPLIANCE
Adjustable levelling feet at the front and rear are provided on the base of the appliance. Adjustment to suit
floor conditions is obtained by rotating in or out the hexagonal feet from the underside of the appliance. A
spirit level should be placed on one of the oven shelves to confirm that the appliance is correctly levelled.
4. FITTING THE STABILITY BRACKET
It is recommended that if the appliance is to be installed with a flexible supply pipe a stability bracket
(SK.4729.A) is fitted and is available from your supplier (see Important Safety Requirements, Page 32).
These instructions should be read in conjunction with the leaflet packed with the stability bracket.
1.
2.
Place the appliance in its intended position and level appliance.
Mark off 250mm from the left hand side of the appliance as shown in (Dimension 'A'), Fig 2a.This is the
centre line of the fixing bracket.
3.
4.
Draw a line 100mm from the front edge of the levelling feet (see Fig 2a) and remove appliance from its
position. Mark off dimension 'B' (see Fig 2a) back from this line on the centre line of the bracket to
locate the front edge of the lower bracket. Fix lower bracket (with two fixing holes) to the floor then
measure the height from floor level to engagement edge on back of appliance, dimension 'C' of Fig. 2b.
Assemble upper bracket to lower bracket so that underside of bracket is dimension 'C' +3mm above
floor level.
Reposition appliance and check that top bracket engages into appliance back as shown in Fig. 2b.
All dimensions in mm
Fig.2b
Fig.2a
34
A S T O R I A 3
5. CONNECTING TO GAS
This appliance is designed to be installed with an
appliance flexible connection only. Supply piping should
not be less than R³/8 (³/8" B.S.P.). Connection is made to
the Rc½ (½" B.S.P.) female threaded entry pipe located
just below the hotplate level on the rear left hand side of
the appliance.
Check for gas soundness after connecting the gas
supply.
The gas bayonet connector must be fitted in the shaded
area indicated in Fig. 3. Take into account that it must
be possible to pull the appliance forward sufficiently. The
hose must not get caught on the stability bracket.
Fig.3
All dimensions in mm
IMPORTANT:
FLEXIBLE TUBING USED MUST
COMPLY WITH BS. 669 CURRENT EDITION. L.P.G. FLEXIBLE CONNECTIONS MUST BE OF A TYPE
SUITABLE FOR L.P.G. AND CAPABLE OF OPERATION UP TO 50mbar AND TO CARRY A RED
STRIPE, BAND OR LABEL.
NOTE: ONLY LIQUID SEALANTS CAN BE USED IN THREADED GAS CONNECTIONS. DO NOT USE
P.T.F.E. TAPE.
6. FITTING THE BATTERY
1.
The battery holder is located at the front left hand
side of the bottom storage compartment (see Fig.
4).
2.
3.
Open bottom compartment flap to gain access to
the battery holder.
From inside the bottom compartment fit the 1.5 volt
battery (see Fig. 4) ensuring it is fitted as indicated
by the symbols on the battery holder.
Fig.4
7. PRESSURE TESTING
1.
The oven injector is used as the pressure test point.
Remove the oven furniture. Remove oven burner box retaining clips (one spring clip from each side)
and remove box front cover. Replace one clip back into the right hand side of the burner box.
Remove oven burner by removing the spring clip from the right hand side of the oven burner and slide
the burner off the injector whilst easing it towards the front of the appliance, taking care not to strain the
F.S.D. phial.
2.
3.
Connect the pressure gauge to the oven injector.
Check the supply pressure by turning the thermostat on and one hotplate tap full on and light the
appropriate burner.
The pressure should be either:
(i) For Natural Gas
(ii) For LP.Gas
20mbar
The pressure must be set to 28 mbar for use on butane or 37 mbar for use
on propane.
4.
5.
Turn off the taps, disconnect the pressure gauge and replace oven burner and cover, ensuring that the
F.S.D. phial is correctly located into the bracket on the burner.
Check operation of oven.
35
A S T O R I A 3
8. CHECKING THE GRILL
Remove the protective film from the grill pan shelf. Fit the grill pan shelf to the splashplate.
Place the grill pan containing the grid on to the grill pan shelf. Light the grill burner by turning the tap to its' full
on position and pressing the ignition button. As soon as the burner is lit the button can be released.
9. CHECKING THE HOTPLATE
Fit the burner crowns, caps and pan supports ensuring that they are correctly seated. Check each of the
hotplate burners in turn by turning each hotplate tap to its full on position and pressing the ignition button. As
soon as the burner is lit the button can be released.
10. CHECKING THE MAIN OVEN
1.
Turn the oven thermostat knob to Mk 9 and press the ignition button. As soon as the burner is alight the
button can be released.
2.
3.
There should now be a low gas rate to the burner, which is the F.S.D. by-pass rate.
When the F.S.D. phial has heated up it opens the F.S.D. valve which allows the main gas supply to the
oven burner.
4.
5.
Set the oven control to Mk 2, close the oven door and check that after about 10 minutes the flame size
has reduced.
Turn off the control and check that the oven flames go out.
GENERAL NOTE
Instruct the user on how to use the appliance and its ignition system.
Refer the user to the wording in the inside cover which gives advice on the safe operation of the appliance.
36
N O T E S
N O T E S
ASTORIA 3 - 311346906
Contents Check List
The loose contents of this pack include:-
No. OFF
DESCRIPTION
2
1
1
1
1
1
1
4
4
2
1
Oven shelves
Consumer questionnaire
Hotplate operation card
Single handle grill pan (small)
Grill pan trivet (small wire)
Grill pan shelf (small)
Green screw pack
Burner crowns
Burner caps
Pan supports
Battery
This handbook was correct on the date it was printed. But this handbook will be
replaced if the specification or appearance change as the cooker is improved.
No.
Off
Maker's Part
Number
Description
Burner Cap - Rapid
1
2
1
1
1
2
1
2
354000610
354000609
354000608
359039100
337000302
337000402
337000502
359033202
Burner Cap - Normal
Burner Cap - Simmer
Burner Crown - Rapid - N.G.
Burner Crown - Rapid - L.P.G.
Burner Crown - Normal
Burner Crown - Simmer
Pan Support
NOTE : Failure to use manufacturers original spares could negate normal BSI approval of the product
Drawing No. 311346906
|