Eizo Nanao Computer Monitor EV2316W User Manual
Important  
Please read PRECAUTIONS, this User’s Manual, and the Setup Guide  
(separate volume) carefully to familiarize yourself with safe and  
effective usage.  
•Please refer to the Setup Guide for basic information ranging from  
connection of the monitor to a PC to using the monitor.  
•The latest User’s Manual is available for download from our web site:  
http://www.eizo.com  
 
Notice for this monitor  
This product is suited to general purposes like creating documents, viewing multimedia content.  
This product has been adjusted specifically for use in the region to which it was originally shipped. If the product is  
used outside the region, it may not operate as specified in the specifications.  
This product may not be covered by warranty for uses other than those described in this manual.  
The specifications noted in this manual are only applicable when the following are used:  
· Power cords provided with the product  
· Signal cables specified by us  
Only use optional products manufactured or specified by us with this product.  
It takes about 30 minutes for the performance of electrical parts to stabilize. Please wait 30 minutes or more after the  
monitor power has been turned on, and then adjust the monitor.  
Monitors should be set to a lower brightness to reduce changes in luminosity caused by long-term use and maintain a  
stable display.  
When the screen image is changed after displaying the same image for extended periods of time, an afterimage may  
appear. Use the screen saver or power save function to avoid displaying the same image for extended periods of time.  
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime (refer to  
“Cleaning” (page 4)).  
The LCD panel is manufactured using high-precision technology. Although, missing pixels or lit pixels may appear on  
the LCD panel, this is not a malfunction. Percentage of effective dots: 99.9994% or higher.  
The backlight of the LCD panel has a fixed lifetime. When the screen becomes dark or begins to flicker, please contact  
your local EIZO representative.  
Do not press on the panel or edge of the frame strongly, as this may result in display malfunctions, such as interference  
patterns, etc. If pressure is continually applied to the panel, it may deteriorate or damage your panel. (If the pressure  
marks remain on the panel, leave the monitor with a black or white screen. The symptom may disappear.)  
Do not scratch or press on the panel with any sharp objects, as this may result in damage to the panel. Do not attempt  
to brush with tissues as this may scratch the panel.  
When the monitor is cold and brought into a room or the room temperature goes up quickly, dew condensation may  
occur on the interior and exterior surfaces of the monitor. In that case, do not turn the monitor on. Instead wait until  
the dew condensation disappears, otherwise it may cause some damage to the monitor.  
Noticeforthismonitor  
3
 
Cleaning  
Attention  
• Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet or panel,  
and also quality deterioration of the image.  
• Never use any thinner, benzene, wax, and abrasive cleaner, which may damage the cabinet or panel.  
Note  
• The optional ScreenCleaner is recommended for cleaning the cabinet and panel surface.  
If necessary, the stains on the cabinet and panel surface can be removed by moistening part of a soft cloth with  
water.  
To use the monitor comfortably  
• An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor according to  
the environmental conditions.  
• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.  
Noticeforthismonitor  
4
   
Toresetthecoloradjustments...................... 35  
                                                                                                                                                                                  
BasicoperationoftheSettingmenu  
                                                                                            
..............12  
Functions  
●  
                                                    
........................................................13  
EV2416W  
●  
                                                     
........................................................16  
WindowsVista................................................18  
                                                            
Toadjustgamma  
                                                                 
.......................................... 22  
Toadjustthecolorsaturation........................ 22  
Toadjusthue................................................. 23  
                                                                                  
                                                          
Rear................................................................10  
●  
                                             
CONTENTS  
Cover ...................................................................... 1  
Chapter 3 Setting Monitor ............................... 31  
3-1. Adjusting Volume.........................................31  
Notice for this monitor ......................................... 3  
Cleaning .................................................................... 4  
To use the monitor comfortably............................. 4  
CONTENTS............................................................. 5  
3-2. Selecting sound source while using the  
DisplayPort signal input..............................31  
3-3. Compensating viewing angle deficiency  
(EV2316W / EV2416W only) ........................ 32  
Chapter 1 Introduction....................................... 7  
1-1. Features ......................................................... 7  
1-2. Controls and Functions ............................... 9  
3-4. Enabling / Disabling DDC/CI  
communication .......................................... 32  
3-5. Locking Operation Buttons....................... 33  
3-6. Setting Orientation ..................................... 33  
3-7. Showing and hiding the EIZO logo........... 33  
3-8. Changing Setting Menu Display Position 34  
3-9. Setting Language........................................ 34  
Front................................................................ 9  
●  
1-3. EIZO LCD Utility Disk...................................11  
Diskcontentsandsoftwareoverview............11  
●  
Touse“ScreenManagerProforLCD  
●  
3-10. Resetting the Monitor to the Default  
Settings........................................................ 35  
(DDC/CI)/EIZOScreenSlicer”......................11  
1-4. Basic Operations and Functions ...............12  
●  
●  
●  
●  
Toreset“EcoViewSenseSettings”.............. 35  
Toresetalladjustmentstothedefault  
Chapter 2 Adjusting Screens.......................... 14  
2-1. Compatible Resolutions .............................14  
settings.......................................................... 35  
Chapter 4 Power Saving Functions ................ 36  
4-1. Setting Power Saving ................................. 36  
EV2316W.......................................................14  
●  
EV2336W.......................................................15  
●  
Monitor.......................................................... 36  
●  
AudioOutput..................................................37  
●  
EV2436W.......................................................17  
●  
4-2. Setting Power Indicator...............................37  
2-2. Setting the Resolution ................................18  
4-3. Enabling / Disabling Automatic  
Windows8/Windows7.................................18  
●  
Brightness Adjustment ..............................37  
●  
●  
●  
AutoEcoView.................................................37  
●  
WindowsXP...................................................18  
MacOSX.......................................................18  
EcoViewOptimizer2..................................... 38  
●  
4-4. Setting the power saving mode when a  
person leaves the monitor......................... 38  
2-3. Adjusting Color............................................19  
Toselectthedisplaymode  
●  
4-5. Checking the power saving level .............. 40  
4-6. Enabling / Disabling Auto Power-OFF...... 40  
Chapter 5 Troubleshooting.............................. 41  
5-1. No picture .....................................................41  
(FineContrastMode)......................................19  
Toperformadvancedadjustments............... 20  
●  
Adjustablesettingsineachmode................. 20  
●  
Toadjustbrightness...................................... 20  
●  
Toadjustcontrast...........................................21  
●  
5-2. Imaging problems (for both digital and  
analog).......................................................... 42  
Toadjustcolortemperature...........................21  
●  
●  
●  
●  
●  
5-3. Imaging problems (for digital only) .......... 43  
5-4. Imaging problems (for analog only) ......... 43  
5-5. Other problems........................................... 44  
Chapter 6 Reference ........................................ 46  
6-1. Attaching the Optional Arm....................... 46  
Tosetoverdriveintensity(EV2336W/  
EV2436Wonly)............................................. 23  
Toadjustgain.................................................24  
●  
2-4. Screen Adjustment..................................... 25  
6-2. Detaching / Attaching the TriStand2  
Stand Base....................................................47  
DigitalSignalInput........................................ 25  
●  
AnalogSignalInput....................................... 25  
●  
6-3. Attaching / Detaching the TriStand2  
Cable Holder................................................ 49  
2-5. Screen Size Changing................................ 29  
ScreenSizeChanging.................................. 29  
●  
6-4. Connecting Multiple PCs ............................51  
Toadjustbrightnessofnon-displayarea...... 30  
●  
CONTENTS  
5
EV2416W....................................................... 57  
                                                     
OutsideDimensions  
                                                                    
...................................... 60  
Accessories................................................... 62  
                                                        
EV2416W  
●  
                                                     
....................................................... 64  
Function)........................................................ 53  
                                                    
Toswitchamonginputsignals.......................51  
Tosetinputsignalselection...........................52  
●  
●  
6-5. Making Use of USB (Universal Serial  
Bus)............................................................... 52  
RequiredSystemEnvironment......................52  
●  
ConnectionProcedure(SetupofUSB  
●  
6-6. Displaying Monitor Information ................ 53  
6-7. Specifications ............................................. 54  
EV2316W...................................................... 54  
●  
EV2336W...................................................... 55  
●  
●  
●  
●  
●  
●  
EV2436W...................................................... 58  
MainDefaultSettings.................................... 60  
6-8. Preset Timing .............................................. 63  
EV2316W...................................................... 63  
●  
EV2336W...................................................... 63  
●  
EV2436W...................................................... 64  
●  
6-9. Glossary....................................................... 65  
Appendix.............................................................. 67  
Trademark ............................................................... 67  
License .................................................................... 67  
ENERGY STAR........................................................ 68  
TCO .......................................................................... 68  
FCC Declaration of Conformity ............................ 69  
Hinweise zur Auswahl des richtigen  
Schwenkarms für Ihren Monitor............................70  
Hinweis zur Ergonomie : ........................................70  
LIMITED WARRANTY..............................................71  
Recycling Information ........................................... 80  
China Measures for RoHS Compliance in  
ChinaRoHS.............................................................. 84  
CONTENTS  
6
Chapter 1 Introduction  
Thank you very much for choosing an EIZO color LCD monitor.  
1-1. Features  
• 23.0″ wide format LCD (EV2316W / EV2336W)  
• 24.1″ wide format LCD (EV2416W / EV2436W)  
• Supports a resolution of 1920 × 1080 (EV2316W / EV2336W)  
• Supports a resolution of 1920 × 1200 (EV2416W / EV2436W)  
• IPS panel with 89˚ horizontal and vertical viewing angles (EV2336W / EV2436W only)  
• Applicable to DisplayPort (applicable to 8 bit)*1  
The DisplayPort input receives both an image signal and an audio signal via a single DisplayPort cable.  
*1 When transmitting an audio signal using the DisplayPort cable, the graphics board must be compatible with audio  
output (see “6-7. Specifications” (page 54)).  
• The FineContrast function allows the user to select the display mode optimum to the displayed image.  
-
The Paper mode reproduces a printed paper effect on the monitor.  
See “To select the display mode (FineContrast Mode)” (page 19).  
• The software “ScreenManager Pro for LCD (DDC/CI)” to adjust the screen using the mouse and keyboard is  
included  
See “1-3. EIZO LCD Utility Disk” (page 11).  
-
EyeCare Filter  
Texture of the paper is reproduced by displaying a translucent image in the foreground of the desktop.  
By using this function with the Paper mode, the screen looks more like paper.  
See “To select the display mode (FineContrast Mode)” (page 19).  
• Supports the power management software “EIZO EcoView NET”  
For more information, refer to our web site (http://www.eizo.com).  
• Power saving function  
Suppressing the power consumption*2 reduces the carbon dioxide emissions. This product is equipped with power saving  
function.  
-
-
0 W power consumption when the main power is off  
Equipped with main power switch.  
When the monitor is not required, the power supply can be shut off using the main power switch.  
Auto EcoView  
The ambient light sensor on the front side of the monitor detects the environmental brightness to adjust the screen  
brightness automatically and comfortably. Excessively high brightness may increase power consumption and cause  
unwanted environmental effects. It may also lead to fatigue of your eyes. Use the Auto EcoView to reduce the  
brightness.  
See “Auto EcoView” (page 37).  
-
-
EcoView Optimizer 2  
The monitor automatically adjusts the screen brightness according to the white level of the input signal. This  
function can reduce the power consumption while maintaining the brightness specified by the input signal.  
See “EcoView Optimizer 2” (page 38).  
EcoView Sense  
The sensor on the front side of the monitor detects the movement of a person. When a person moves away from the  
monitor, the monitor shifts to the power saving mode automatically and does not display the images on the screen.  
Therefore, the function reduces the power consumption. The sensitivity and time until the power saving mode is  
activated can be set according to the monitor usage environment and movement of the user.  
See “4-4. Setting the power saving mode when a person leaves the monitor” (page 38).  
Chapter1Introduction  
7
 
*2 Reference values:  
EV2316W  
Maximum power consumption: 43 W (Brightness Max., when a USB device is connected, speaker working, at  
default settings)  
Standard power consumption: 14 W (Brightness 120 cd/m2, when no USB device is connected, speaker not working,  
at default settings)  
EV2336W  
Maximum power consumption: 40 W (Brightness Max., when a USB device is connected, speaker working, at  
default settings)  
Standard power consumption: 14 W (100VAC, Brightness 120 cd/m2, when no USB device is connected, speaker not  
working, at default settings)  
Standard power consumption: 15 W (200VAC, Brightness 120 cd/m2, when no USB device is connected, speaker not  
working, at default settings)  
EV2416W  
Maximum power consumption: 40 W (Brightness Max., when a USB device is connected, speaker working, at  
default settings)  
Standard power consumption: 11 W (Brightness 120 cd/m2, when no USB device is connected, speaker not working,  
at default settings)  
EV2436W  
Maximum power consumption: 60 W (Brightness Max., when a USB device is connected, speaker working, at  
default settings)  
Standard power consumption: 19 W (Brightness 120 cd/m2, when no USB device is connected, speaker not working,  
at default settings)  
• Up View (EV2316W / EV2416W only)  
The viewing angle is adjusted so that the screen looks like a front view when the screen is looked up.  
See “3-3. Compensating viewing angle deficiency (EV2316W / EV2416W only)” (page 32).  
• Supports portrait and landscape formats (FlexStand2 only)  
• Displays HDCP (High-bandwidth Digital Protection) protected contents.  
Note  
• This monitor supports the portrait display. This function allows you to change the orientation of the Setting menu when  
using the monitor screen in vertical display position (see “3-6. Setting Orientation” (page 33)).  
• When using the monitor screen in a portrait position, the graphics board supporting portrait display is required. When  
placing the monitor in a portrait position, the settings of your graphics board need to be changed. Refer to the User’s  
Manual of the graphics board for details.  
Chapter1Introduction  
8
1-2. Controls and Functions  
Front  
●
Settingmenu*1  
Settingmenu*1  
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
FlexStand2  
TriStand2  
Detectsthemovementofapersoninfrontofthemonitor(EcoViewSensefunction(page  
38)).  
1. EcoView Sense sensor  
2. Ambient light sensor Detectsambientbrightness(AutoEcoViewfunction(page37)).  
Displaysthesettingmenuofthepowersavingfunction(AutoEcoView(page37)and  
EcoViewOptimizer2(page38))andEcoViewSense(page38).  
3.  
button  
4.  
5.  
button  
Switchesinputsignalsfordisplay(page51).  
ChangestheFineContrastmode(page19).  
button  
button  
DisplaystheSettingmenu,determinesanitemonthemenuscreen,andsavesvalues  
adjusted(page12).  
6.  
• Providesthemenuselectionaswellastheadjustmentandsettingofafunction.  
7.  
,
button*2  
•  
button:Displaysthevolumeadjustmentmenu(page31).  
button:DisplaystheBrightnessadjustmentmenu(page20).  
8.  
button  
Turnsthepoweronoroff.  
Indicatesthemonitor’soperationstatus.  
Blue:  
Operating  
9. Power indicator  
Orange:  
OFF:  
Powersavingmode  
Mainpower/Poweroff  
*1 See “1-4. Basic Operations and Functions” (page 12) for how to use.  
*2 In this User’s Manual, the button may be hereafter simply displayed as , and the  
button as  
.
Chapter1Introduction  
9
 
Rear  
●
15  
16  
15  
16  
17  
17  
18  
18  
19  
19  
13  
13  
20  
20  
14  
14  
21  
21*3  
1011  
12  
1011  
12  
FlexStand2  
TriStand2  
10. Main power switch  
11. Power connector  
Turnsthemainpoweronoroff.  
Connectsthepowercord.  
Left:DisplayPortconnector/Center:DVI-Dconnector/Right:D-Submini15-pin  
connector  
12. Input signal connector  
13. Security lock slot  
14. Speaker  
ComplieswithKensington’sMicroSaversecuritysystem.  
Outputsaudiosource.  
Handleusedfortransportation  
Attention  
15. Handle  
• Firmly grasp and hold the monitor by the bottom while grabbing the handle, and carefully  
convey the monitor so as not to drop it.  
16. Stand*4  
Adjuststheheightandangle(tiltandswivel)ofthemonitor.  
ConnectsaperipheralUSBdevice.  
17. USB port (DOWN)  
18. USB port (UP)  
19. Headphone jack  
20. Stereo mini jack  
21. Cable holder  
ConnectstheUSBcableforusingtheUSBHubfunction(page52).  
Connectstheheadphones.  
Connectsthestereominijackcable(commerciallyavailableproduct).  
Coversthemonitorcables.  
*3 See “6-3. Attaching / Detaching the TriStand2 Cable Holder” (page 49) for how to attach the cable holder.  
*4 An optional arm (or an optional stand) can be attached by removing the stand (see “6-1. Attaching the Optional Arm” (page 46)).  
Chapter1Introduction  
10  
 
1-3. EIZO LCD Utility Disk  
An “EIZO LCD Utility Disk” (CD-ROM) is supplied with this product. The following table shows the disk contents  
and the overview of the software programs.  
Disk contents and software overview  
The disk includes software programs for adjustment, and User’s Manual. Refer to Readme.txt file on the disk  
●
for software startup procedures or file access procedures.  
Item  
Overview  
Windows  
Macintosh  
Screenadjustmentpatternfiles  
Usedwhenadjustingtheimageofanalog  
signalinputmanually.  
√
√
ScreenManagerProforLCD  
(DDC/CI)  
Softwareforadjustingthescreenusingthe  
mouseandkeyboard.  
√
√
-
-
EIZOScreenSlicer  
Softwarethatdividesascreenandlaysout  
multiplewindowsefficiently.  
User’sManualofthismonitor(PDFfile)  
Readme.txtfile  
√
√
√
√
To use “ScreenManager Pro for LCD (DDC/CI) / EIZO ScreenSlicer”  
For the installation and use of “ScreenManager Pro for LCD (DDC/CI) / EIZO SceenSlicer”, refer to the  
respective User’s Manual on the disk.  
●
Chapter1Introduction  
11  
   
1-4. Basic Operations and Functions  
Basic operation of the Setting menu  
●
1.  
Displaying the Setting menu  
1. Press  
. The Setting menu appears.  
Adjusting / Setting  
1. Choose a menu to adjust / set with , , and then press  
2.  
. The Sub menu appears.  
2. Choose an item to adjust / set with , , and then press  
3. Adjust / set the selected item with , , and then press  
. The adjustment / setting menu appears.  
.
Exiting  
3.  
1. Choose “Return” from the Sub menu and press  
. The Setting menu appears.  
. The Setting menu quits.  
2. Choose “Exit” from the Main menu and press  
Note  
• The Setting menu can also be exited by pressing  
twice quickly.  
Chapter1Introduction  
12  
   
Functions  
●
The following table shows the Setting menu and setting items of each menu.  
Main menu  
Setting  
Reference  
Color*1  
Brightness  
Contrast  
“2-3.AdjustingColor”(page19)  
Temperature  
Gamma  
AdvancedSettings Saturation  
Hue  
Overdrive*2  
Gain  
ColorReset  
“Toresetthecoloradjustments”(page35)  
“ScreenSizeChanging”(page29)  
“2-4.ScreenAdjustment”(page25)  
Screen  
ScreenSize  
Smoothing  
AnalogAdjustment*3 AutoScreenAdjust  
AutoRangeAdjust  
Clock  
Phase  
Hor.Position  
Ver.Position  
Source  
Sound  
“3-2.Selectingsoundsourcewhileusing  
theDisplayPortsignalinput”(page31)  
“AudioOutput”(page37)  
PowerSave  
PowerSave  
EcoTimer  
PowerManager  
MonitorSettings  
“4-1.SettingPowerSaving”(page36)  
“4-6.Enabling/DisablingAutoPower-  
OFF”(page40)  
UpView*4  
“3-3.Compensatingviewingangle  
deficiency(EV2316W/EV2416Wonly)”  
(page32)  
InputSignal  
PowerIndicator  
Language  
“Tosetinputsignalselection”(page52)  
“4-2.SettingPowerIndicator”(page37)  
“3-9.SettingLanguage”(page34)  
“3-4.Enabling/DisablingDDC/CI  
communication”(page32)  
DDC/CI  
BorderIntensity  
“Toadjustbrightnessofnon-displayarea”  
(page30)  
MenuSettings  
Orientation  
Logo  
“3-6.SettingOrientation”(page33)  
“3-7.ShowingandhidingtheEIZOlogo”  
(page33)  
MenuPosition  
“3-8.ChangingSettingMenuDisplay  
Position”(page34)  
Reset  
“Toresetalladjustmentstothedefault  
settings”(page35)  
Information  
“6-6.DisplayingMonitorInformation”  
(page53)  
*1 The adjustment / settings available on the “Color” menu depend on the selected Color mode. The above table shows  
the sub menus when the User1 or User2 mode is selected.  
*2 EV2336W / EV2436W only  
*3 These functions can be adjusted with analog input.  
*4 EV2316W / EV2416W only  
Chapter1Introduction  
13  
 
Chapter 2 Adjusting Screens  
2-1. Compatible Resolutions  
The monitor supports the following resolutions.  
EV2316W  
●
Analog Input (D-Sub)  
Vertical Scan  
Frequency  
60Hz  
Resolution  
Applicable Signals  
Dot Clock  
640×480  
800×600  
VGA  
VESA  
VESA  
CEA-861  
VESA  
60Hz  
60Hz  
60Hz  
60Hz  
60Hz  
60Hz  
60Hz  
1024×768  
1280×720  
1280×960  
1280×1024  
1680×1050  
1920×1080*1  
148.5MHz  
(Max.)  
VESA  
VESACVT,VESACVTRB  
CEA-861  
Digital Input (DVI-D)  
Vertical Scan  
Frequency  
60Hz  
Resolution  
Applicable Signals  
Dot Clock  
640×480  
800×600  
VGA  
VESA  
VESA  
CEA-861  
VESA  
60Hz  
60Hz  
60Hz  
60Hz  
60Hz  
60Hz  
60Hz  
1024×768  
1280×720  
1280×960  
1280×1024  
1680×1050  
1920×1080*1  
148.5MHz  
(Max.)  
VESA  
VESACVT,VESACVTRB  
CEA-861  
Digital Input (DisplayPort)  
Vertical Scan  
Frequency  
60Hz  
Resolution  
Applicable Signals  
Dot Clock  
640×480  
720×480(4:3)  
720×480(16:9)  
800×600  
VGA,CEA-861  
CEA-861  
60Hz  
60Hz  
60Hz  
CEA-861  
VESA  
1024×768  
1280×720  
VESA  
CEA-861  
60Hz  
60Hz  
148.5MHz  
(Max.)  
1280×960  
VESA  
60Hz  
1280×1024  
1680×1050  
1920×1080*1  
VESA  
60Hz  
60Hz  
60Hz  
VESACVT,VESACVTRB  
CEA-861  
ThegraphicsboardshouldcomplywiththeVESAstandardandCEA-861standard.  
*1 Recommended resolution  
Chapter2AdjustingScreens  
14  
   
EV2336W  
●
Analog Input (D-Sub)  
Vertical Scan  
Frequency  
~75Hz  
Resolution  
Applicable Signals  
Dot Clock  
640×480  
720×400  
800×600  
VGA,VESA  
VGATEXT  
VESA  
70Hz  
~75Hz  
1024×768  
1280×720  
1280×960  
1280×1024  
1680×1050  
1920×1080*1  
VESA  
CEA-861  
VESA  
VESA  
~75Hz  
60Hz  
60Hz  
~75Hz  
60Hz  
60Hz  
148.5MHz  
(Max.)  
VESACVT,VESACVTRB  
CEA-861  
Digital Input (DVI-D)  
Vertical Scan  
Frequency  
60Hz  
Resolution  
Applicable Signals  
Dot Clock  
640×480  
720×400  
800×600  
VGA  
VGATEXT  
VESA  
70Hz  
60Hz  
1024×768  
1280×720  
1280×960  
1280×1024  
1680×1050  
1920×1080*1  
VESA  
CEA-861  
VESA  
VESA  
60Hz  
60Hz  
60Hz  
60Hz  
60Hz  
60Hz  
148.5MHz  
(Max.)  
VESACVT,VESACVTRB  
CEA-861  
Digital Input (DisplayPort)  
Vertical Scan  
Frequency  
60Hz  
Resolution  
Applicable Signals  
Dot Clock  
640×480  
720×400  
720×480(4:3)  
720×480(16:9)  
800×600  
VGA,CEA-861  
VGATEXT  
CEA-861  
70Hz  
60Hz  
60Hz  
60Hz  
60Hz  
60Hz  
CEA-861  
VESA  
VESA  
CEA-861  
148.5MHz  
(Max.)  
1024×768  
1280×720  
1280×960  
VESA  
60Hz  
1280×1024  
1680×1050  
1920×1080*1  
VESA  
60Hz  
60Hz  
60Hz  
VESACVT,VESACVTRB  
CEA-861  
ThegraphicsboardshouldcomplywiththeVESAstandardandCEA-861standard.  
*1 Recommended resolution  
Chapter2AdjustingScreens  
15  
 
EV2416W  
●
Analog Input (D-Sub)  
Vertical Scan  
Frequency  
60Hz  
Resolution  
Applicable Signals  
Dot Clock  
640×480  
800×600  
VGA  
VESA  
60Hz  
1024×768  
1280×720*1  
1280×960  
1280×1024  
1600×1200  
1680×1050  
1920×1200*2  
VESA  
CEA-861  
VESA  
VESA  
VESA  
60Hz  
60Hz  
60Hz  
60Hz  
60Hz  
60Hz  
60Hz  
193.3MHz  
(Max.)  
VESACVT,VESACVTRB  
VESACVT,VESACVTRB  
Digital Input (DVI-D)  
Vertical Scan  
Frequency  
60Hz  
Resolution  
Applicable Signals  
Dot Clock  
640×480  
800×600  
VGA  
VESA  
60Hz  
1024×768  
1280×720*1  
1280×960  
1280×1024  
1600×1200  
1680×1050  
1920×1200*2  
VESA  
CEA-861  
VESA  
VESA  
60Hz  
60Hz  
60Hz  
60Hz  
60Hz  
60Hz  
60Hz  
162MHz  
(Max.)  
VESA  
VESACVT,VESACVTRB  
VESACVTRB  
Digital Input (DisplayPort)  
Vertical Scan  
Frequency  
60Hz  
Resolution  
Applicable Signals  
Dot Clock  
640×480  
720×480(4:3)  
720×480(16:9)  
800×600  
VGA,CEA-861  
CEA-861  
60Hz  
60Hz  
60Hz  
CEA-861  
VESA  
1024×768  
1280×720*1  
1280×960  
VESA  
CEA-861  
VESA  
60Hz  
60Hz  
60Hz  
162MHz  
(Max.)  
1280×1024  
1600×1200  
1680×1050  
1920×1200*2  
VESA  
VESA  
60Hz  
60Hz  
60Hz  
60Hz  
VESACVT,VESACVTRB  
VESACVTRB  
ThegraphicsboardshouldcomplywiththeVESAstandardandCEA-861standard.  
*1 For this resolution, the “Screen Size” setting is “Full Screen” (see “2-5. Screen Size Changing” (page 29)).  
*2 Recommended resolution  
Chapter2AdjustingScreens  
16  
 
EV2436W  
●
Analog Input (D-Sub)  
Vertical Scan  
Frequency  
~75Hz  
70Hz  
Resolution  
Applicable Signals  
Dot Clock  
640×480  
720×400  
VGA,VESA  
VGATEXT  
800×600  
VESA  
VESA  
CEA-861  
VESA  
VESA  
~75Hz  
~75Hz  
60Hz  
60Hz  
~75Hz  
60Hz  
1024×768  
1280×720  
1280×960  
1280×1024  
1600×1200  
1680×1050  
1920×1200*1  
193.3MHz  
(Max.)  
VESA  
VESACVT,VESACVTRB  
VESACVT,VESACVTRB  
60Hz  
60Hz  
Digital Input (DVI-D)  
Vertical Scan  
Frequency  
60Hz  
Resolution  
Applicable Signals  
Dot Clock  
640×480  
720×400  
800×600  
VGA  
VGATEXT  
VESA  
70Hz  
60Hz  
1024×768  
1280×720  
1280×960  
1280×1024  
1600×1200  
1680×1050  
1920×1200*1  
VESA  
CEA-861  
VESA  
VESA  
60Hz  
60Hz  
60Hz  
60Hz  
60Hz  
60Hz  
60Hz  
162MHz  
(Max.)  
VESA  
VESACVT,VESACVTRB  
VESACVTRB  
Digital Input (DisplayPort)  
Vertical Scan  
Frequency  
60Hz  
Resolution  
Applicable Signals  
Dot Clock  
640×480  
720×400  
720×480(4:3)  
720×480(16:9)  
800×600  
VGA,CEA-861  
VGATEXT  
CEA-861  
70Hz  
60Hz  
60Hz  
60Hz  
CEA-861  
VESA  
1024×768  
1280×720  
VESA  
CEA-861  
60Hz  
60Hz  
162MHz  
(Max.)  
1280×960  
VESA  
60Hz  
1280×1024  
1600×1200  
1680×1050  
1920×1200*1  
VESA  
VESA  
60Hz  
60Hz  
60Hz  
60Hz  
VESACVT,VESACVTRB  
VESACVTRB  
ThegraphicsboardshouldcomplywiththeVESAstandardandCEA-861standard.  
*1 Recommended resolution  
Chapter2AdjustingScreens  
17  
 
2-2. Setting the Resolution  
When you connect the monitor to the PC and find that the resolution is improper, or when you want to change the  
resolution, follow the procedure below.  
Windows 8 / Windows 7  
●
1. For Windows 8, click the “Desktop” tile on the Start Screen to display the desktop.  
2. Right-click the mouse anywhere on the desktop except for icons.  
3. From the displayed menu, click “Screen resolution”.  
4. On the “Screen Resolution” dialog box, select the monitor.  
5. Click “Resolution” to select the desired resolution.  
6. Click the “OK” button.  
7. When a confirmation dialog box is displayed, click “Keep changes”.  
Windows Vista  
1. Right-click the mouse anywhere on the desktop except for icons.  
●
2. From the displayed menu, click “Personalize”.  
3. On the “Personalization” window, click “Display Settings”.  
4. On the “Display Settings” dialog box, select the “Monitor” tab and select desired resolution in the  
“Resolution” field.  
5. Click the “OK” button.  
6. When a confirmation dialog box is displayed, click “Yes”.  
Windows XP  
1. Right-click the mouse anywhere on the desktop except for icons.  
●
2. From the displayed menu, click “Properties”.  
3. When the “Display Properties” dialog box is displayed, click the “Settings” tab and select desired resolution  
for “Screen resolution” under “Display”.  
4. Click the “OK” button to close the dialog box.  
Mac OS X  
1. Select “System Preferences” from the Apple menu.  
●
2. When the “System Preferences” dialog box is displayed, click “Displays” for “Hardware”.  
3. On the displayed dialog box, select the “Display” tab and select desired resolution in the “Resolutions” field.  
4. Your selection will be reflected immediately. When you are satisfied with the selected resolution, close the  
window.  
Chapter2AdjustingScreens  
18  
 
2-3. Adjusting Color  
To select the display mode (FineContrast Mode)  
This function allows easy selection of a desired mode according to monitor application.  
●
Display Modes  
Mode  
Purpose  
User1  
User2  
sRGB  
Paper  
Selectthistodefineadesiredsetofparametersettings.  
SuitableforcolormatchingwithsRGBcompatibleperipherals.  
Producesaprintedpapereffect.Suitablefordisplayingimagesfrommediasuchasbooks  
anddocuments.  
Movie  
Suitableforplayingbackanimatedimages.  
Themodemenu  
appears.  
Procedure  
1. Press  
.
The mode menu appears at the bottom left of the screen.  
2. The mode among the list is highlighted in turn each time  
is pressed.  
You can switch the mode with or while the mode menu is displayed.  
→User1←→User2←→sRGB←→Paper←→Movie←  
Note  
• The Setting menu and the Mode menu cannot be displayed at the same time.  
• “ScreenManager Pro for LCD (DDC/CI)” allows you to select the FineContrast mode automatically according to the  
application used (see “Chapter 3 Auto FineContrast” in the “ScreenManager Pro for LCD (DDC/CI)” User’s Manual).  
Chapter2AdjustingScreens  
19  
     
To perform advanced adjustments  
The “Color” menu of the Setting menu allows you to set and save the independent color adjustment for each  
●
●
mode.  
Attention  
• It takes about 30 minutes for the performance of electrical parts to stabilize. Please wait 30 minutes or more after the  
monitor power has been turned on, and then adjust the monitor.  
• Perform the range adjustment first when adjusting color for analog signals (see “To adjust color gradation automatically”  
(page 28)).  
• The same image may be seen in different colors on multiple monitors due to their monitor-specific characteristics. Make  
fine color adjustment visually when matching colors on multiple monitors.  
Note  
• Using the “ScreenManager Pro for LCD (DDC/CI)” allows you to perform the color adjustment by using the mouse and  
keyboard of your PC. (Refer to “Chapter 4 Color Adjustment” in the User’s Manual for “ScreenManager Pro for LCD  
(DDC/CI)”.)  
Adjustable settings in each mode  
The adjustable settings depend on the mode. (Non-adjustable or non-settable function cannot be selected.)  
√: Adjustable -: Not adjustable  
FineContrast Mode  
Function  
User1  
User2  
sRGB  
Paper  
Movie  
Brightness  
Contrast  
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
-
√
-
√
√
√
-
Temperature  
Gamma  
-
√
-
-
AdvancedSettings  
Saturation  
Hue  
Overdrive*1  
-
-
√
√
-
-
-
-
-
Gain  
-
-
-
ColorReset  
√
√
√
*1 EV2336W / EV2436W only  
To adjust brightness  
The screen brightness is adjusted by changing the brightness of the backlight (light source from the LCD back  
●
panel).  
Adjustable range  
0 to 100  
Procedure  
1. Press  
.
2. Use or for adjustment.  
3. Press  
to exit.  
Note  
• If you feel that the image is too dark even if the brightness is set to 100, adjust the contrast.  
• Alternatively, you can use “Brightness” under “Color” in the Adjustment menu to adjust it.  
• To adjust the screen brightness automatically and comfortably, see “4-3. Enabling / Disabling Automatic Brightness  
Adjustment” (page 37).  
Chapter2AdjustingScreens  
20  
     
To adjust contrast  
The brightness of the screen is adjusted by varying the video signal level.  
●
Adjustable range  
0 to 100  
Procedure  
1. Choose “Color” in the Setting menu, and press  
2. Choose “Contrast” in the “Color” menu, and press  
The “Contrast” menu appears.  
.
.
3. Use or for adjustment.  
4. Press  
to exit.  
Note  
• In the contrast of 50, every color gradation is displayed.  
• When adjusting the monitor, it is recommended to perform the brightness adjustment which may not lose the gradation  
characteristics, prior to the contrast adjustment.  
• Perform the contrast adjustment in the following cases.  
- When you feel the image is too dark even if the brightness is set to 100 (Set the contrast to higher than 50.)  
To adjust color temperature  
Color temperature can be adjusted.  
●
The color temperature is normally used to express the hue of “White” and / or “Black” by a numerical value.  
The value is expressed in degrees “K” (Kelvin).  
The screen becomes reddish at a low color temperature, and bluish at a high color temperature, like the flame  
temperature. A gain preset value is set for each color temperature setting value.  
Adjustable range  
Off, 4000 K-10000 K (specified by every 500 K unit, including 9300 K)  
Procedure  
1. Choose “Color” in the Setting menu, and press  
2. Choose “Temperature” in the “Color” menu, and press  
The “Temperature” menu appears.  
.
.
3. Use or for adjustment.  
4. Press  
to exit.  
Note  
• The value shown in “K” is available only as reference.  
• “Gain” allows you to perform more advanced adjustment (see “To adjust gain” (page 24)).  
• If you set to “Off”, the image is displayed in the preset color of the monitor (Gain: 100 for each RGB).  
• When gain is changed, the color temperature is changed to “Off”.  
Chapter2AdjustingScreens  
21  
 
To adjust gamma  
Gamma can be adjusted. The brightness of the monitor varies depending on the input signal, however, the  
variation rate is not proportional to the input signal. To keep the balance between the input signal and the  
brightness of the monitor is called as “Gamma correction”.  
●
Adjustable range  
1.8, 2.0, 2.2  
Procedure  
1. Choose “Color” in the Setting menu, and press  
2. Choose “Gamma” in the “Color” menu, and press  
The “Gamma” menu appears.  
.
.
3. Use or for adjustment.  
4. Press  
to exit.  
Note  
• If “Paper” is selected in the FineContrast mode, the gamma value is displayed for “Paper”. The setting “Paper” is  
specially meant to get the displayed image look like it is printed on paper.  
To adjust the color saturation  
This function allows you to adjust color saturation.  
Adjustable range  
●
-50 to 50  
Procedure  
1. Choose “Color” in the Setting menu, and press  
.
2. Choose “Advanced Settings” in the “Color” menu, and press  
3. Choose “Saturation” in the “Advanced Settings” menu, and press  
The “Saturation” menu appears.  
.
.
4. Use or for adjustment.  
5. Press  
to exit.  
Attention  
• Using this function may make some color gradations unavailable for display.  
Note  
• The minimum value (-50) changes the screen to monochrome.  
Chapter2AdjustingScreens  
22  
 
To adjust hue  
This function allows you to adjust hue.  
●
●
Adjustable range  
-50 to 50  
Procedure  
1. Choose “Color” in the Setting menu, and press  
.
2. Choose “Advanced Settings” in the “Color” menu, and press  
3. Choose “Hue” in the “Advanced Settings” menu, and press  
The “Hue” menu appears.  
.
.
4. Use or for adjustment.  
5. Press  
to exit.  
Attention  
• Using this function may make some color gradations unavailable for display.  
To set overdrive intensity (EV2336W / EV2436W only)  
This function allows you to set overdrive intensity based on the use of the monitor. You can reduce Image lags  
by setting it to “Enhanced” when displaying animated images.  
Adjustable range  
Enhanced, Standard, Off  
Procedure  
1. Choose “Color” in the Setting menu, and press  
.
2. Choose “Advanced Settings” in the “Color” menu, and press  
3. Choose “Overdrive” in the “Advanced Settings” menu, and press  
The “Overdrive” menu appears.  
.
.
4. Use or for adjustment.  
5. Press  
to exit.  
Attention  
• The overdrive function is disabled in the following cases:  
- The vertical scan frequency of input signals is more than 60 Hz  
- Select “Normal” during “Screen Size” (excluding the case that display resolution is 1920 × 1080 (EV2336W) or 1920  
× 1200 (EV2436W)).  
Chapter2AdjustingScreens  
23  
   
To adjust gain  
●
The brightness of each color component red, green, and blue is called “Gain”. You can change the hue of  
“white” by adjusting gain.  
Adjustable range  
0 to 100  
Procedure  
1. Choose “Color” in the Setting menu, and press  
.
2. Choose “Advanced Settings” in the “Color” menu, and press  
3. Choose “Gain” in the “Advanced Settings” menu, and press  
The “Gain” menu appears.  
.
.
4. Adjust gain with or for each of red, green, and blue.  
5. Press  
to exit.  
Attention  
• Using this function may make some color gradations unavailable for display.  
Note  
• The value of gain changes with that of color temperature.  
• When gain is changed, the color temperature is changed to “Off”.  
Chapter2AdjustingScreens  
24  
   
2-4. Screen Adjustment  
Digital Signal Input  
When digital signals are input, images are displayed correctly based on the preset data of the monitor, but if  
characters and / or lines appear blurred, go to “To modify blurred characters / lines” (page 28).  
When performing more advanced adjustment, see “2-3. Adjusting Color” (page 19) and subsequent pages.  
●
Analog Signal Input  
●
Attention  
• It takes about 30 minutes for the performance of electrical parts to stabilize. Please wait 30 minutes or more after the  
monitor power has been turned on, and then adjust the monitor.  
• The Self Adjust (automatic screen adjustment) function does not work for the images under the resolution of 800 × 600  
(SVGA).  
• The self adjustment (or automatic screen adjustment) function works correctly when an image is fully displayed over the  
Windows or Macintosh display area. They do not work properly in the cases below:  
- When an image is displayed only on a part of the screen (command prompt window, for example)  
- When a black background (wallpaper, etc.) is in use  
Also, these functions cannot work properly in some graphic boards.  
The monitor screen adjustment is used to suppress flickering of the screen or adjust screen position and screen  
size correctly according to the PC to be used.  
Note  
• The Self Adjust function works when all of the following conditions are satisfied:  
- When a signal is input into the monitor for the first time or when a resolution or vertical / horizontal scan frequency  
not used before is set  
If the screen is not displayed correctly even after performing the Self Adjust operation, adjust the screen  
according to the procedures on the following pages to use the monitor comfortably.  
Setting Procedures  
Perform the auto adjustment.  
1.  
To adjust flickering, screen position, and screen size automatically  
●
Procedure  
1. Choose “Screen” in the Setting menu, and press  
2. Choose “Analog Adjustment” in the “Screen” menu, and press  
3. Choose “Auto Screen Adjust” in the “Analog Adjustment” menu, and press  
4. Select “Yes” with or , and press  
.
.
.
.
Flickering, screen position, and screen size are corrected by the auto-adjustment function.  
Ifthescreenisnotdisplayedcorrectlyevenafterperformingtheautoadjustment,performadjustments  
accordingtothefollowingprocedure.Ifthescreenisdisplayedcorrectly,goto“5.Adjustingcolorgradation.”  
(page28).  
Chapter2AdjustingScreens  
25  
   
Prepare to use analog screen adjustment patterns.  
2.  
Load the “EIZO LCD Utility Disk” to your PC, and then open the “Screen adjustment pattern files”.  
Note  
• For details and instructions on opening the “Screen adjustment pattern files”, refer to the Readme.txt file.  
Perform the auto adjustment again with the analog screen adjustment pattern  
displayed.  
3.  
To adjust flickering, screen position, and screen size automatically  
●
Procedure  
1. Display Pattern 1 in full screen on the monitor using the “Screen adjustment pattern files”.  
2. Choose “Screen” in the Setting menu, and press  
3. Choose “Analog Adjustment” in the “Screen” menu, and press  
4. Choose “Auto Screen Adjust” in the “Analog Adjustment” menu, and press  
5. Select “Yes” with or , and press  
.
.
.
.
Flickering, screen position, and screen size are corrected by the auto-adjustment function.  
Ifthescreenisnotdisplayedcorrectlyevenafterperformingtheautoadjustment,performadjustments  
accordingtothefollowingprocedure.Ifthescreenisdisplayedcorrectly,goto“5.Adjustingcolorgradation.”  
(page28).  
Choose “Screen” from the Setting menu to perform advanced adjustments.  
4.  
Adjust the clock, phase and position, in this order.  
To eliminate vertical bars  
Procedure  
●
1. Choose “Analog Adjustment” in the “Screen” menu, and press  
2. Choose “Clock” in the “Analog Adjustment” menu, and press  
The “Clock” menu appears.  
.
.
3. Adjust the clock with or to eliminate vertical bars.  
Press or slowly so as not to miss the adjustment point.  
4. Press  
to exit.  
When blurring, flickering or bars appear on the screen after adjustment, proceed to “To remove flickering or blurring ”.  
Chapter2AdjustingScreens  
26  
 
To remove flickering or blurring  
Procedure  
●
1. Choose “Analog Adjustment” in the “Screen” menu, and press  
2. Choose “Phase” in the “Analog Adjustment” menu, and press  
The “Phase” menu appears.  
.
.
3. Adjust the phase with or to minimize flickering or blurring.  
4. Press  
to exit.  
When vertical bars appear on the screen after adjustment, go back to “To eliminate vertical bars ”.  
(Clock → Phase → Position)  
Attention  
• Flickering or blurring may not be eliminated depending on your PC or graphics board.  
To correct the screen position  
●
Note  
• Since the number of pixels and the pixel positions are fixed on the LCD monitor, only one position is provided to display  
images correctly. The position adjustment is made to shift an image to the correct position.  
Procedure  
1. Choose “Analog Adjustment” in the “Screen” menu, and press  
.
2. Choose “Hor.Position” or “Ver.Position” from the “Analog Adjustment” menu, and press  
The “Hor. Position” or “Ver. Position” menu appears.  
.
3. Adjust the position with or  
4. Press to exit.  
.
5. Close Pattern 1.  
Chapter2AdjustingScreens  
27  
   
Adjusting color gradation.  
5.  
To adjust color gradation automatically  
●
Every color gradation (0 to 255) can be displayed by adjusting the signal output level.  
Procedure  
1. Display Pattern 2 in full screen on the monitor using the “Screen adjustment pattern files”.  
2. Choose “Screen” in the Setting menu, and press  
3. Choose “Analog Adjustment” in the “Screen” menu, and press  
4. Choose “Auto Range Adjust” in the “Analog Adjustment” menu, and press  
.
.
.
5. Select “Yes” with or , and press  
The output range is set automatically.  
6. Close Pattern 2.  
.
Modify blurred characters or lines.  
To modify blurred characters / lines  
6.  
●
When an image is displayed with a resolution other than recommended, the characters or lines of the  
displayed image may blur.  
Attention  
• Smoothing setting may not be required depending on the display resolution. (You cannot choose the smoothing icon.)  
Adjustable range  
1 to 5  
Procedure  
1. Choose “Screen” in the Setting menu, and press  
2. Choose “Smoothing” in the “Screen” menu, and press  
The “Smoothing” menu appears.  
.
.
3. Use or for adjustment.  
4. Press  
to exit.  
Chapter2AdjustingScreens  
28  
     
2-5. Screen Size Changing  
Screen Size Changing  
The image with the resolution other than the recommended resolution is displayed in full screen automatically.  
●
You can change the screen size by using the “Screen Size” function.  
Setting  
Function  
FullScreen  
Displaysanimageinfullscreen.Imagesaredistortedinsomecasesbecausethevertical  
rateisnotequaltothehorizontalrate.  
Enlarged  
Normal*1  
Displaysanimageinfullscreen.Insomecases,ablankhorizontalorverticalborder  
appearstoequalizetheverticalrateandthehorizontalrate.  
Displaysimageswiththespecifiedresolution.  
*1 EV2336W / EV2436W only  
Example: Image size 1024 × 768  
FullScreen  
Enlarged  
Normal  
EV2316W:  
EV2336W:  
EV2416W:  
EV2436W:  
(1920×1080)  
(1920×1080)  
(1920×1200)  
(1920×1200)  
(1440×1080)  
(1440×1080)  
(1600×1200)  
(1600×1200)  
(-)  
(1024×768)  
(-)  
(1024×768)  
Procedure  
1. Choose “Screen” in the Setting menu, and press  
2. Choose “Screen Size” in the “Screen” menu, and press  
The “Screen Size” menu appears.  
.
.
3. Select “Full Screen”, “Enlarged”, or “Normal” with or  
.
4. Press  
to exit.  
Attention  
• Selecting “Normal” may make some color gradations unavailable for display.  
• When a 1280 × 720 resolution image is displayed on the EV2416W, the screen size is “Full Screen”.  
Chapter2AdjustingScreens  
29  
     
To adjust brightness of non-display area  
A border (black area with no image) around the image appears in the “Normal” or “Enlarged” mode.  
●
Border  
Procedure  
1. Choose “Monitor Settings” in the Setting menu, and press  
.
2. Choose “Border Intensity” in the “Monitor Settings” menu, and press  
The “Border Intensity” menu appears.  
.
3. Use or for adjustment.  
4. Press  
to exit.  
Chapter2AdjustingScreens  
30  
   
Chapter 3 Setting Monitor  
3-1. Adjusting Volume  
This function allows you to adjust the volume.  
Adjustable range  
0 to 30  
Procedure  
1. Press  
.
2. Use or for adjustment.  
3. Press  
to exit.  
Note  
• The volume for the speakers and the headphone can be set individually.  
3-2. Selecting sound source while using the DisplayPort  
signal input  
This function allows you to switch sound source during DisplayPort signal input. You can select the Stereo Mini  
Jack or DisplayPort.  
Procedure  
1. Choose “Sound” in the Setting menu, and press  
2. Choose “Source” in the “Sound” menu, and press  
The “Source” menu appears.  
.
.
3. Select “Stereo Mini Jack” or “DisplayPort” with or  
.
4. Press  
to exit.  
Note  
• This function is available with DisplayPort signal input.  
Chapter3SettingMonitor  
31  
     
3-3. Compensating viewing angle deficiency (EV2316W  
/ EV2416W only)  
When the screen is to be viewed from below, the viewing angle can be compensated for so the screen looks as if it  
is being seen from directly ahead.  
Off  
-20˚  
-40˚  
Adjustable range  
-40˚, -20˚, Off  
Procedure  
1. Choose “Monitor Settings” in the Setting menu, and press  
2. Choose “Up View” in the “Monitor Settings” menu, and press  
The “Up View” menu appears.  
.
.
3. Select “-40˚”, “-20˚”, or “Off” with or  
.
4. Press  
to exit.  
Attention  
• The setting is turned “Off” in the following cases:  
- “Orientation” of the Setting menu is set to “Portrait”.  
- “sRGB” is selected from the FineContrast mode.  
• Depending on the viewing angle, switching the setting may make the screen less visible.  
3-4. Enabling / Disabling DDC/CI communication  
This function allows you to enable / disable the DDC/CI communication (see “6-9. Glossary” (page 65)).  
Procedure  
1. Choose “Monitor Settings” in the Setting menu, and press  
2. Choose “DDC/CI” in the “Monitor Settings” menu, and press  
The “DDC/CI” menu appears.  
.
.
3. Select “On” or “Off” with or  
.
4. Press  
to exit.  
Note  
• The DisplayPort input of this monitor does not support DDC/CI communication.  
Chapter3SettingMonitor  
32  
     
3-5. Locking Operation Buttons  
This function allows you to lock the settings to prevent them being changed.  
Procedure  
1. Press to turn off the monitor.  
2. Hold down  
while pressing to turn on the monitor.  
The Lock / Unlock setting is toggled by performing the operation in step 2.  
Note  
• The following operations are available even if the buttons are locked:  
- Turning on or off the monitor with the Power button  
3-6. Setting Orientation  
This function allows you to change the orientation of the Setting menu when using the monitor screen in vertical  
display position.  
Procedure  
1. Choose “Monitor Settings” in the Setting menu, and press  
.
2. Choose “Menu Settings” in the “Monitor Settings” menu, and press  
3. Choose “Orientation” in the “Menu Settings” menu, and press  
The “Orientation” menu appears.  
.
.
4. Select “Landscape” or “Portrait” with or  
5. Press to exit.  
.
6. When selecting “Portrait”, turn the monitor screen 90˚ in clockwise direction.  
Attention  
• Be sure that the cables are correctly connected.  
• Be sure to turn the monitor screen after pulling up the screen to the uppermost position of the stand and setting the  
screen tilted upward.  
Note  
• For using the monitor with “Portrait” position, the graphics board supporting portrait display is required. When placing  
the monitor in a “Portrait” position, settings of your graphics board need to be changed. Refer to the User’s Manual of  
the graphics board for details.  
3-7. Showing and hiding the EIZO logo  
When the monitor is turned on, the EIZO logo appears on the screen. You can choose to show or hide the display of  
the EIZO logo.  
Procedure  
1. Choose “Monitor Settings” in the Setting menu, and press  
.
2. Choose “Menu Settings” in the “Monitor Settings” menu, and press  
.
3. Choose “Logo” in the “Menu Settings” menu, and press  
The “Logo” menu appears.  
.
4. Select “On” or “Off” with or  
5. Press to exit.  
.
Chapter3SettingMonitor  
33  
       
3-8. Changing Setting Menu Display Position  
You can change the display position of the Setting menu.  
Procedure  
1. Choose “Monitor Settings” in the Setting menu, and press  
.
2. Choose “Menu Settings” in the “Monitor Settings” menu, and press  
3. Choose “Menu Position” in the “Menu Settings” menu, and press  
The “Menu Position” menu appears.  
.
.
4. Choose the position with or  
5. Press to exit.  
.
3-9. Setting Language  
This function allows you to select a language for the Setting menu or messages.  
Selectable languages  
English, German, French, Spanish, Italian, Swedish, Japanese, Simplified Chinese, Traditional Chinese  
Procedure  
1. Choose “Monitor Settings” in the Setting menu, and press  
2. Choose “Language” in the “Monitor Settings” menu, and press  
The “Language” menu appears.  
.
.
3. Choose a language with or  
4. Press to exit.  
.
Chapter3SettingMonitor  
34  
     
3-10.Resetting the Monitor to the Default Settings  
The setting values are reset to the default settings.  
Attention  
• After resetting, you cannot undo the operation.  
Note  
• Regarding the default setting, see “Main Default Settings” (page 60).  
To reset the color adjustments  
This function only resets the color adjustments for the currently selected mode to the default settings.  
●
Procedure  
1. Choose “Color” in the Setting menu, and press  
.
2. Choose “Color Reset” in the “Color” menu, and press  
.
3. Select “Yes” with or  
4. Press  
.
.
The color adjustments revert to the default settings.  
To reset “EcoView Sense Settings”  
This function resets adjustments for “EcoView Sense Settings” to the default settings.  
●
●
Procedure  
1. Press  
2. Choose “EcoView Sense Settings” in the “EcoView Menu”, and press  
3. Choose “Reset” in the “EcoView Sense Settings”, and press  
4. Select “Yes” with or  
5. Press  
.
.
.
.
.
The “EcoView Sense Settings” adjustments revert to the default settings.  
Note  
• “EcoView Sense Settings” can be changed and reset only when “EcoView Sense” is set to “On” (see “4-4. Setting the  
power saving mode when a person leaves the monitor” (page 38)).  
To reset all adjustments to the default settings  
This function resets all adjustments to the default settings.  
Procedure  
1. Choose “Monitor Settings” in the Setting menu, and press  
2. Choose “Reset” in the “Monitor Settings” menu, and press  
.
.
3. Select “Yes” with or  
4. Press  
.
.
All adjustments revert to the default settings.  
Chapter3SettingMonitor  
35  
     
Chapter 4 Power Saving Functions  
4-1. Setting Power Saving  
Monitor  
●
This function allows you to set the monitor into the power saving mode according to the PC status. When the  
monitor has shifted to the power saving mode, the images on the screen are not displayed.  
Attention  
• Turning off the main power switch or unplugging the power cord completely shuts off power supply to the monitor.  
• When the monitor is in power saving mode, devices connected to the USB downstream port will still work. Therefore,  
power consumption of the monitor varies with connected devices even in the power saving mode.  
• Power consumption varies even when the stereo mini jack cable is connected.  
Note  
• The monitor changes to the power saving mode about 15 seconds after the signal input ceases to be detected.  
Procedure  
1. Choose “PowerManager” in the Setting menu, and press  
2. Choose “Power Save” in the “PowerManager” menu, and press  
The “Power Save” menu appears.  
.
.
3. Select “On” or “Off” with or  
4. Press to exit.  
.
Power Saving System  
Analog Signal Input  
This monitor complies with the VESA DPM standard.  
PC Monitor  
Power Indicator  
On  
Powersaving STAND-BY  
Operating  
Blue  
Powersavingmode  
Orange  
mode  
SUSPENDED  
OFF  
PowerOff  
Powersavingmode  
Orange  
Digital Signal Input  
• DVI  
This monitor complies with the DVI DMPM standard.  
• DisplayPort  
This monitor complies with the DisplayPort Standard V1.1a.  
PC  
Monitor  
Power Indicator  
On  
Operating  
Blue  
Powersavingmode  
PowerOff  
Powersavingmode  
Powersavingmode  
Orange  
Orange  
Exiting the power saving mode  
If the monitor receives input, it automatically exits the power saving mode and returns to the normal display  
mode.  
Chapter4PowerSavingFunctions  
36  
   
Audio Output  
●
This monitor allows you to turn off the audio output from the speakers / headphone at the power saving mode.  
Procedure  
1. Choose “Sound” in the Setting menu, and press  
2. Choose “Power Save” in the “Sound” menu, and press  
The “Power Save” menu appears.  
.
.
3. Select “Sound On” or “Sound Off” with or  
4. Press to exit.  
.
4-2. Setting Power Indicator  
This function allows you to set the power indicator (blue) ON / OFF in the monitor ON condition.  
Procedure  
1. Choose “Monitor Settings” in the Setting menu, and press  
.
2. Choose “Power Indicator” in the “Monitor Settings” menu, and press  
The “Power Indicator” menu appears.  
.
3. Select “On” or “Off” with or  
4. Press to exit.  
.
4-3. Enabling / Disabling Automatic Brightness  
Adjustment  
Auto EcoView  
●
The ambient light sensor on the front side of the monitor detects the environmental brightness to adjust the  
screen brightness automatically and comfortably by using the Auto EcoView function.  
Attention  
• Be careful not to block the ambient light sensor on the lower side of the monitor when using the Auto EcoView function.  
Procedure  
1. Press  
.
2. Choose “Auto EcoView” in the “EcoView Menu” menu, and press  
The “Auto EcoView” menu appears.  
.
3. Select “High”, “Standard”, or “Off” with or  
.
4. Press  
to exit.  
Note  
• As “Brightness” in the Setting menu is changed, the auto adjustment range for Auto EcoView is also changed.  
• Set to “High” if you feel a little brighter with “Standard” setting status.  
Chapter4PowerSavingFunctions  
37  
         
EcoView Optimizer 2  
Using the EcoView Optimizer 2 function automatically adjusts the screen brightness according to the white  
level of the input signal. This function can reduce the power consumption while maintaining the brightness  
specified by the input signal.  
●
Procedure  
1. Press  
.
2. Choose “EcoView Optimizer 2” in the “EcoView Menu” menu, and press  
The “EcoView Optimizer 2” menu appears.  
.
3. Select “On” or “Off” with or  
.
4. Press  
to exit.  
Note  
• When “Movie” is selected from the FineContrast mode, the setting is turned “Off”.  
• When the EcoView Optimizer 2 function is “On”, the appearance of pale color may change. If that bothers you, set this  
function to “Off”.  
4-4. Setting the power saving mode when a person  
leaves the monitor  
The sensor on the front side of the monitor detects the movement of a person by using the EcoView Sense function.  
When a person moves away from the monitor, it shifts to the power saving mode automatically and does not display  
the images on the screen to reduce the power consumption. When a person comes near the monitor again, it  
recovers from the power saving mode and displays the images. The sensitivity and time until the power saving  
mode is activated can be set according to the monitor usage environment and movement of the user.  
Note  
• At the time of shifting to power saving mode, the message that indicates shifting is displayed.  
Procedure  
1. Press  
.
2. Choose “EcoView Sense” in the “EcoView Menu”, and press  
The “EcoView Sense” menu appears.  
.
3. Select “On” or “Off” with or  
4. Press to exit.  
.
Chapter4PowerSavingFunctions  
38  
     
5. When “On” is selected, select “EcoView Sense Settings” for setting the details.  
Item  
Setting Range  
Description  
Time  
5,30sec  
Specifiesthetimefromwhenapersonleavesthemonitoruntilthe  
1,3,5,10,15,30,45, “NoPresencedetected”messageappears.Themonitorshiftsto  
60min  
thepowersavingmodeabout20secondsafterthemessageis  
displayed.  
Sensitivity  
Level5  
Level4  
Level3  
Level2  
Level1  
Whenthesettinglevelishigh(“Level5”atmaximum),evenminor  
movementsofapersonaredetected,causingthemonitortoshift  
tothepowersavingmodeonlyinfrequently.Ontheotherhand,  
whenthesettinglevelislow(“Level1”atminimum),onlymajor  
movementsofapersonaredetected,allowingthemonitortoshift  
tothepowersavingmodefrequently.EcoViewSenseisactivated  
whenthesensoronthefrontsideofthemonitordetectsthe  
movementofheat.Therefore,thesensitivityshouldbechanged  
dependingonthetypicaluser’sclothesorthetypicalroom  
temperature.Ifthemonitorshiftstoorrecoversfromthepower  
savingmodecontrarytoyourexpectations,trychangingthesetting  
level.  
Reset  
-
Thisfunctionresetsalladjustmentstothedefaultsettings.  
Note  
• When the monitor is used in the “Portrait” direction, the detection sensitivity is lower than the “Landscape” direction.  
Try increasing the sensitivity setting value when switching the mode to the power saving mode.  
• To use the monitor comfortably, increase the sensitivity for high temperatures, which reduces the detection sensitivity,  
and reduce the sensitivity for low temperatures, which increases the detection sensitivity.  
Chapter4PowerSavingFunctions  
39  
4-5. Checking the power saving level  
The EcoView menu allows you to check Power Reduction, CO2 Reduction, and Eco Performance Level. The more  
indicators light up representing the Eco Performance Level, the higher the power saving level attained.  
Example: EV2436W  
Indicator  
Procedure  
1. Press  
.
The “EcoView Menu” menu appears.  
Note  
• Power reduction: the backlight’s reduction of power consumption as a result of the adjusted brightness value.  
CO2 reduction: converted from the “Power reduction” value, this is an estimate of the quantity of CO2 emissions reduced  
when using the monitor for 1 hour.  
*
The numeric value is a result of a calculation based on a default setting (0.000555 t -CO2/kWh) determined by a Japanese  
ministerial ordinance (2006, Ministry of Economy, Trade and Industry, Ministry of Environment, civil code article 3) and  
may differ depending on country and year.  
4-6. Enabling / Disabling Auto Power-OFF  
This function allows you to switch the setting to turn off the monitor automatically after a specified time has passed  
in the power saving mode.  
Adjustable range  
Off, 0, 1, 2, 3, 5, 10, 15, 20, 25, 30, 45 min, 1, 2, 3, 4, 5 h  
Procedure  
1. Choose “PowerManager” in the Setting menu, and press  
2. Choose “Eco Timer” in the “PowerManager”, and press  
.
.
3. Select “Off” or time to turn off the monitor with or  
4. Press to exit.  
.
Chapter4PowerSavingFunctions  
40  
   
Chapter 5 Troubleshooting  
If a problem still remains after applying the suggested remedies, contact your local EIZO representative.  
5-1. No picture  
Problem  
Possible cause and remedy  
1. No picture  
• Powerindicatordoesnotlight.  
• Checkwhetherthepowercordisconnectedproperly.  
• Turnthemainpowerswitchon.  
• Press  
.
• Turnoffthemainpower,andthenturnitonagainafew  
minuteslater.  
• Powerindicatorislightingblue.  
• Powerindicatorislightingorange.  
• Increase“Brightness”,“Contrast”,or“Gain”intheSetting  
menu(see“Toperformadvancedadjustments”(page20)).  
• Switchtheinputsignalwith  
.
• Movethemouseorpressanykeyonthekeyboard.  
• CheckwhetherthePCisturnedon.  
• WhentheEcoViewSensefunctionis“On”,themonitor  
mayhaveshiftedtothepowersavingmode.Comenear  
tothemonitor.Ifthescreenisnotdisplayed,movethe  
mouseorpressanykeyonthekeyboard.  
• DependingonthePCandgraphicsboard,theinputsignal  
isnotdetectedandthemonitordoesnotrecoverfrom  
thepowersavingmode.Ifthescreenisnotdisplayed  
evenaftermovingthemouseorpressinganykeyonthe  
keyboard,turnthemonitoroffandonusingitspower  
button.Whenthescreenisdisplayed,executethe  
followingprocedure.Theproblemmaybeimproved.  
1. Press toturnoffthemonitor.  
2. Holddown whilepressing toturnonthe  
monitor.  
“x”isdisplayedonthemenutitleof“Information”ofthe  
Settingmenu(see“6-6.DisplayingMonitorInformation”  
(page53)).  
3. RebootthePC.  
Toreturntotheprevioussetting,performsteps1to3  
again.  
• Powerindicatorisflashingorange.  
• ThedevicethatisconnectedusingDisplayPorthasa  
problem.Solvetheproblem,turnoffthemonitor,andthen  
turnitonagain.RefertotheUser’sManualoftheoutput  
deviceforfurtherdetails.  
Chapter5Troubleshooting  
41  
 
Problem  
Possible cause and remedy  
2. The message below appears.  
Thismessageappearswhenthesignalisnotinputcorrectly  
evenwhenthemonitorfunctionsproperly.  
• Themessageshowsthattheinputsignalis  
outofthespecifiedfrequencyrange.  
Example:  
• CheckwhetherthePCisconfiguredtomeettheresolution  
andverticalscanfrequencyrequirementsofthemonitor  
(see“2-1.CompatibleResolutions”(page14)).  
• RebootthePC.  
• Selectanappropriatesettingusingthegraphicsboard’s  
utility.RefertotheUser’sManualofthegraphicsboard  
fordetails.  
5-2. Imaging problems (for both digital and analog)  
Problem  
Possible cause and remedy  
1. The screen is too bright or too dark.  
• Use“Brightness”or“Contrast”intheSettingmenuto  
adjustit.(TheLCDmonitorbacklighthasalimitedlife  
span.Whenthescreenbecomesdarkorbeginstoflicker,  
contactyourlocalEIZOrepresentative.)  
• Ifthescreenistoobright,turnonAutoEcoView.The  
monitordetectstheenvironmentalbrightnesstoadjustthe  
screenbrightnessautomatically.  
2. Characters are blurred.  
• CheckwhetherthePCisconfiguredtomeettheresolution  
andverticalscanfrequencyrequirementsofthemonitor  
(see“2-1.CompatibleResolutions”(page14)).  
• Whenanimageisdisplayedwitharesolutionotherthan  
recommended,thecharactersorlinesofthedisplayed  
imagemayblur.Use“Smoothing”and“ScreenSize”inthe  
Settingmenutoadjustthedisplay(see“Tomodifyblurred  
characters/lines”(page28),and“ScreenSizeChanging”  
(page29)).  
3. Afterimages appear.  
• AfterimagesareparticulartoLCDmonitors.Avoid  
displayingthesameimageforalongtime.  
• Usethescreensaverorpowersavefunctiontoavoid  
displayingthesameimageforextendedperiodsoftime.  
4. Green / red / blue / white dots or defective  
dots remain on the screen.  
• ThisisduetoLCDpanelcharacteristicsandisnota  
failure.  
5. Interference patterns or pressure marks  
remain on the screen.  
• Leavethemonitorwithawhiteorblackscreen.The  
symptommaydisappear.  
6. Noise appears on the screen.  
• IntheSettingmenu,set“Overdrive”to“Off”(see“Toset  
overdriveintensity(EV2336W/EV2436Wonly)”(page23)).  
• WhenenteringtheHDCPsignals,thenormalimagesmay  
notbedisplayedimmediately.  
Chapter5Troubleshooting  
42  
 
5-3. Imaging problems (for digital only)  
Problem  
Possible cause and remedy  
1. The monitor configuration is changed to  
single under the multiple monitor configu-  
ration (when DisplayPort is connected).  
• WhentwomonitorsareconnectedtoonePCusing  
DisplayPort,andthepowertooneofthemonitorsis  
turnedoffwiththepowerbutton,thescreensettingmay  
bechangedtothesinglemonitorconfiguration.Insucha  
case,enablethe“DPHotPlug”functionwiththefollowing  
procedures.Enablingthisfunctionmayincreasethe  
powerconsumption.  
1. Press toturnoffthemonitor.  
2. Holddown whilepressing toturnonthemonitor.  
Eachtimetheoperationenables/disablesthisfunction  
alternatively.  
Thecurrentsettingstatuscanbeidentifiedbasedonthe  
colorusedtodisplaytheinputportorsignalerror.  
Setting  
Input port  
Signal Error  
Disable  
(default  
setting)  
Enable  
5-4. Imaging problems (for analog only)  
Problem  
Possible cause and remedy  
1. Display position is incorrect.  
• Use“Position”intheSettingmenutocorrecttheimage  
position(see“Tocorrectthescreenposition”(page27)).  
• Iftheproblempersists,usethegraphicsboard’sutilityif  
availabletochangethedisplayposition.  
2. Vertical bars appear on the screen or a  
part of the image is flickering.  
• Use“Clock”intheSettingmenutoadjustit(see“To  
eliminateverticalbars”(page26)).  
3. Whole screen is flickering or blurring.  
• Use“Phase”intheSettingmenutoadjustit(see“To  
removeflickeringorblurring”(page27)).  
Chapter5Troubleshooting  
43  
 
5-5. Other problems  
Problem  
Possible cause and remedy  
1. The Setting menu does not appear.  
• Checkwhethertheoperationlockfunctionisactive(see  
“3-5.LockingOperationButtons”(page33)).  
2. The “Smoothing” on the Setting menu  
“Screen” cannot be selected.  
• Youcannotchoose“smoothing”whenthescreenis  
displayedinthefollowingresolutionsorsettings.  
-Theresolutionis1920×1080(EV2316W/EV2336W)  
-Theresolutionis1920×1200(EV2416W/EV2436W)  
-ScreenSizeis“Normal”(EV2336W/EV2436Wonly)  
3. The auto adjustment function does not  
work.  
• Thisfunctiondoesnotworkduringdigitalsignalinput.  
• ThisfunctionisintendedforuseontheMacintoshand  
onAT-compatiblePCrunningWindows.Itdoesnotwork  
properlywhenanimageisdisplayedonlyonapartofthe  
screen(commandpromptwindow,forexample)orwhena  
blackbackground(wallpaper,etc.)isinuse.  
• Thisfunctiondoesnotworkcorrectlywithsomegraphics  
boards.  
4. No audio output.  
• Checkwhetherthestereominijackcableisconnected  
properly.  
• Checkwhethervolumeissetto0.  
• CheckthesettingofthePCandtheaudioplayback  
software.  
• DuringDisplayPortsignalinput,checkthe“Source”  
setting(see“3-2.Selectingsoundsourcewhileusingthe  
DisplayPortsignalinput”(page31)).  
5. (When using EcoView Sense)  
The images remain to be displayed when  
you move away from the monitor. / The  
images do not reappear when you come  
near it.  
• Checkthesettingenvironmentofthemonitor.Presence  
Sensormaynotworkcorrectlyinthefollowing  
environments.  
-Themonitorislocatedinaplaceaffectedbywind.  
-Thereissomeheatemittingdevicenearthemonitor.  
-Thereissomeobstacleinfrontofthesensor.  
• Checkwhetheranydirtonthesensor.Cleanthesensor  
withasoftcloth.  
• Checkwhetheryouareinfrontofthemonitor.The  
EcoViewSensefunctionisactivatedwhenthesensoron  
thefrontsideofthemonitordetectsthemovementofheat.  
• Inthehightemperatureconditions,themonitormaynot  
recoverfromthepowersavingmode.Ifthescreenisnot  
displayedevenaftermovingthemouseorpressingany  
keyonthekeyboard,turnthemonitoroffandonusingits  
powerbutton.Whenthescreenisdisplayed,increasethe  
detectionsensitivityvalue(see“4-4.Settingthepower  
savingmodewhenapersonleavesthemonitor”(page38)).  
Chapter5Troubleshooting  
44  
 
Problem  
Possible cause and remedy  
6. USB devices connected to the monitor do  
not work.  
• CheckwhethertheUSBcableisconnectedcorrectly(see  
“6-5.MakingUseofUSB(UniversalSerialBus)”(page52)).  
• ChangetheUSBporttoanotherone.IfthePCor  
peripheraldevicesworkscorrectlybychangingtheUSB  
port,contactyourlocalEIZOrepresentative.(Refertothe  
manualofthePCfordetails.)  
• RebootthePC.  
• IftheperipheraldevicesworkcorrectlywhenthePCand  
peripheraldevicesareconnecteddirectly,pleasecontact  
yourlocalEIZOrepresentative.  
• CheckwhetherthePCandOSareUSBcompliant.(For  
USBcomplianceoftherespectivedevices,consulttheir  
manufacturers.)  
• CheckthePC’sBIOSsettingforUSBwhenusing  
Windows.(RefertothemanualofthePCfordetails.)  
Chapter5Troubleshooting  
45  
Chapter 6 Reference  
6-1. Attaching the Optional Arm  
An optional arm (or an optional stand) can be attached by removing the stand section. Please refer to our web site  
for the corresponding optional arm (or optional stand). http://www.eizo.com  
Attention  
• When attaching an arm or stand, follow the instructions of their User’s Manual.  
• When using another manufacturer’s arm or stand, confirm the following in advance and select one conforming to the VESA  
standard.  
- Clearance between the screw holes: 100 mm × 100 mm  
- Thickness of plate: 2.6 mm  
- Strong enough to support weight of the monitor unit (except the stand) and attachments such as cables.  
• When using another manufacturer’s arm or stand, use the screws as described below.  
- FlexStand2: Screws fixing the stand to the monitor  
- TriStand2: Screws supplied with this product (M4 × 12 mm)  
• When using an arm or stand, attach it to meet the following tilt angles of the monitor.  
- Up 45˚, down 45˚ (horizontal display, and vertical display rotated 90 degrees clockwise)  
• Connect the cables after attaching an arm or stand.  
• Do not move the removed stand up and down. Doing so may result in injury or device damage.  
• The monitor and arm or stand are heavy. Dropping them may result in injury or equipment damage.  
• When setting the monitor to the portrait style, turn the monitor screen 90˚ in clockwise direction.  
Procedure  
Lay the LCD monitor on a soft cloth spread over on a stable surface with the  
panel surface facing down.  
1.  
Remove the stand.  
2.  
Using a screwdriver, loosen the screws securing the unit and the stand (FlexStand2: four positions, TriStand2:  
three positions).  
Attach the arm or stand to the monitor.  
3.  
Secure the monitor to the arm or stand using the screws specified in the User’s Manual of the arm or stand.  
Chapter6Reference  
46  
   
6-2. Detaching / Attaching the TriStand2 Stand Base  
Note  
• There are 2 types of shapes for the stand brace and the base mounting section (refer to the figures in the procedure). Check  
the shape of the monitor you have purchased.  
Detaching procedure  
The Stand base that was attached during setup can be detached using the following procedures.  
Lay the LCD monitor on a soft cloth spread over on a stable surface with the  
panel surface facing down.  
1.  
Turn the fixing screw for the Stand base in the “RELEASE” direction to detach  
the base.  
2.  
Remove the Stand base while lifting it up.  
3.  
Chapter6Reference  
47  
 
Attaching procedure  
The once removed the Stand base can be attached to the monitor again with the following procedures.  
Lay the LCD monitor on a soft cloth spread over on a stable surface with the  
panel surface facing down.  
1.  
Hold the Stand base with the “REAR” side facing upward, align the hole (a) of  
the Stand base with the tab (b) at the bottom of the monitor, and snap the tab  
into the hole.  
2.  
Turn the supplied screw in the “LOCK” direction to lock the Stand base.  
3.  
Tighten the screw firmly to the end.  
Tightenscrew,then  
pressknobflat.  
Tightenscrew,then  
pressknobflat.  
Place the monitor on a stable surface.  
4.  
Chapter6Reference  
48  
6-3. Attaching / Detaching the TriStand2 Cable Holder  
When you want to use the cable holder with TriStand2, follow the procedure below. The holder can also be  
removed.  
Note  
• FlexStand2 is a set comprised of the stand and the cable holder.  
Attaching procedure  
Pass the cables through the cable holder.  
1.  
Shut the bottom of the cable holder.  
2.  
While holding the shut section, insert the cable holder into the Stand base.  
3.  
Note  
• The cable holder can be inserted either perpendicular or parallel to the base. Change the direction of the cable holder  
according to the conditions of the cables.  
Chapter6Reference  
49  
   
Detaching procedure  
Shut the bottom of the cable holder.  
1.  
While holding the shut section, lift the cable holder upward to remove it from  
the Stand base.  
2.  
Chapter6Reference  
50  
6-4. Connecting Multiple PCs  
The product has multiple connections to PCs and allows you to switch to one of the connections for display.  
Connection examples  
DisplayPort  
connector  
D-Sub  
connector  
DVI-Dconnector  
Digital  
(DisplayPort)  
Digital(DVI)  
Analog(D-Sub)  
Signalcable  
(suppliedFD-C39)  
Signalcable  
(optionMD-C87)  
Signalcable  
(suppliedPP200)  
D-Submini15-pin  
connector  
DisplayPort  
connector  
DVIconnector  
ToPC2  
ToPC1  
ToPC3  
To switch among input signals  
●
The input signal switches each time  
is pressed.  
When the signal is switched, the active input port name appears at the top right corner of the screen.  
Chapter6Reference  
51  
   
To set input signal selection  
●
Setting  
Function  
Auto  
ThemonitorrecognizestheconnectorthroughwhichPCsignalsareinput.  
WhenaPCisturnedofforentersthepowersavingmode,themonitorautomatically  
displaysanothersignal.  
Manual  
Themonitordisplaysthesignalfromtheselectedconnectordespitethesignalinput.Select  
theinputsignalfordisplayusingthe  
operationbutton.  
Procedure  
1. Choose “Monitor Settings” from the Adjustment menu, and press  
2. Choose “Input Signal” from “Monitor Settings”, and press  
.
.
3. Select “Auto” or “Manual” with or  
.
4. Press  
to exit.  
Note  
• If you select “Auto”, the monitor enters the power saving mode after all the PCs have entered the power saving mode or  
have been switched off.  
6-5. Making Use of USB (Universal Serial Bus)  
This monitor has a USB hub. It works as a USB hub when connected to a USB-compatible PC, allowing the  
connection of peripheral USB devices.  
Required System Environment  
• A PC equipped with a USB port  
●
• Windows 2000 / XP / Vista / 7 / 8 or Mac OS 9.2.2 and Mac OS X 10.2 or later  
• USB cable (commercially available product)  
Attention  
• This monitor may not work depending on PC, OS or peripheral devices to be used. For USB compatibility of peripheral  
devices, contact their manufacturers.  
• When the monitor is in power saving mode, devices connected to the USB downstream port will still work. Therefore,  
power consumption of the monitor varies with connected devices even in the power saving mode.  
• When the main power of the monitor is Off, a device connected to the USB downstream port will not operate.  
Chapter6Reference  
52  
     
Connection Procedure (Setup of USB Function)  
1. Connect the monitor first to a PC using the signal cable, and run the PC.  
2. Connect the USB cable between the USB downstream port of the PC and the USB upstream port of the  
monitor.  
●
The USB hub function is set up automatically upon connection of the USB cable.  
3. Connect the peripheral USB devices to the USB downstream port of the monitor.  
USB  
downstream  
port  
USB  
upstream  
port  
6-6. Displaying Monitor Information  
This function allows you to display the model name, serial number, usage time, resolution, and input signal.  
Procedure  
1. Choose “Information” in the Setting menu, and press  
The “Information” menu appears.  
.
Attention  
• When you turn on the monitor for the first time, the usage time may be more than 0 due to a factory inspection.  
Chapter6Reference  
53  
   
6-7. Specifications  
EV2316W  
●
LCDPanel  
Size  
23.0-inch(580mm)  
Type  
TFTcolorLCD,LEDbacklight  
Anti-GlareHardCoating  
Horizontal170˚,vertical160˚(CR≥10)  
0.2655mm  
Surfacetreatment  
Viewingangles  
DotPitch  
ResponseTime  
Black-white-black:Approx.5ms  
31-68kHz  
HorizontalScan Analog  
Frequency  
Digital  
DVI  
31-68kHz  
DisplayPort 31-68kHz  
55-61Hz(non-interlace)  
59-61Hz(non-interlace)  
VerticalScan  
Frequency  
Analog  
Digital  
DVI  
DisplayPort 59-61Hz(non-interlace)  
1920Dots×1080Lines  
148.5MHz  
Resolution  
Max.DotClock Analog  
Digital  
DVI  
DisplayPort 148.5MHz  
Approx.16.77millioncolors  
148.5MHz  
Max.DisplayColor  
DisplayArea(H×V)  
PowerSupply  
509.7mm(20.1inch)×286.7mm(11.3inch)  
100-120VAC±10%,50/60Hz0.75A  
200-240VAC±10%,50/60Hz0.45A  
Power  
ScreenDisplayOn  
43Worless  
Consumption  
Powersavingmode  
0.3Worless (withnoUSBconnections,“EcoViewSense”:“Off”,and  
“Sound”-“PowerSave”:“SoundOff”)  
PowerOff  
0.3Worless  
MainPowerOff  
0W  
InputSignalConnector  
D-Submini15-pin  
DVI-Dconnector(ApplicabletoHDCP)  
DisplayPort(StandardV1.1a,applicabletoHDCP)  
ApplicableFormat(Audiosignal)  
- 2chlinearPCM  
 (32kHz/44.1kHz/48kHz/88.2kHz/96kHz)  
AnalogInputSignal(Sync)  
AnalogInputSignal(Video)  
Separate,TTL,positive/negative  
Analog,Positive(0.7Vp-p/75Ω)  
DigitalSignal(DVI)TransmissionSystem TMDS(SingleLink)  
AudioOutput  
Speakeroutput:1.0W+1.0W(8Ω,THD+N:10%orless)  
Headphoneoutput:2mW+2mW(32Ω,THD+N:3%orless)  
LineInput  
Inputimpedance:44kΩ(typ.)  
Inputlevel:2.0Vrms(Max.)  
Plug&Play  
Analog/Digital(DVI-D):VESADDC2B/EDIDstructure1.3  
Digital(DisplayPort):VESADisplayPort/EDIDstructure1.4  
Dimensions  
(Width)×  
(Height)×  
(Depth)  
Mainunit(FlexStand2) 540mm(21.3inch)×360-513.5mm(14.2inch-20.2inch)×245.5mm  
(9.7inch)  
Mainunit(TriStand2)  
540mm(21.3inch)×387.5-447.5mm(15.3inch-17.6inch)×200mm  
(7.9inch)  
Mainunit(without  
stand)  
540mm(21.3inch)×317.5mm(12.5inch)×56mm(2.2inch)  
Chapter6Reference  
54  
   
Mass  
Mainunit(FlexStand2) Approx.5.7kg(12.6lbs.)  
Mainunit(TriStand2)  
Approx.4.3kg(9.5lbs.)  
Approx.3.1kg(6.8lbs.)  
Mainunit(without  
stand)  
Movablerange FlexStand2  
Tilt:  
30˚Up,0˚Down  
Swivel:  
172˚Right,172˚Left  
Adjustableheight:  
195mm(7.7inch)(179mm(7.0inch)fortiltof  
0˚)  
Rotation:  
Tilt:  
90˚(Clockwise)  
TriStand2  
25˚Up,0˚Down  
Swivel:  
172˚Right,172˚Left  
60mm(2.36inch)  
Adjustableheight:  
Operating:  
Environmental Temperature  
Conditions  
5˚Cto35˚C(41˚Fto95˚F)  
-20˚Cto60˚C(-4˚Fto140˚F)  
Transportation/  
Storage:  
Humidity  
Operating:  
20%to80%R.H.(nocondensation)  
10%to90%R.H.(nocondensation)  
Transportation/  
Storage:  
AirPressure  
Operating:  
700to1,060hPa  
200to1,060hPa  
Transportation/  
Storage:  
USB  
Standard  
Port  
USBSpecificationRevision2.0  
Upstreamport×1,Downstreamport×2  
CommunicationSpeed 480Mbps(high),12Mbps(full),1.5Mbps(low)  
Supplycurrent  
Downstream:  
Max.500mA/1port  
EV2336W  
●
LCDPanel  
Size  
23.0-inch(580mm)  
Type  
TFTcolorLCD,LEDbacklight  
Anti-GlareHardCoating  
Surfacetreatment  
Viewingangles  
DotPitch  
Horizontal178˚,vertical178˚(CR≥10)  
0.2652mm  
ResponseTime  
Black-white-black:Approx.16ms  
Gray-to-gray:Approx.6ms(Overdrivesetting:Enhanced)  
31-81kHz  
HorizontalScan Analog  
Frequency  
Digital  
DVI  
31-68kHz  
DisplayPort 31-68kHz  
55-76Hz(non-interlace)  
59-61Hz(non-interlace)(VGATEXT:69-71Hz)  
VerticalScan  
Frequency  
Analog  
Digital  
DVI  
DisplayPort 59-61Hz(non-interlace)(VGATEXT:69-71Hz)  
Resolution  
1920Dots×1080Lines  
148.5MHz  
Max.DotClock Analog  
Digital  
DVI  
DisplayPort 148.5MHz  
Approx.16.77millioncolors  
148.5MHz  
Max.DisplayColor  
DisplayArea(H×V)  
PowerSupply  
509.1mm(20inch)×286.4mm(11.3inch)  
100-120VAC±10%,50/60Hz0.8A  
200-240VAC±10%,50/60Hz0.5A  
Chapter6Reference  
55  
 
Power  
Consumption  
ScreenDisplayOn  
Powersavingmode  
40Worless  
0.3Worless (withnoUSBconnections,“EcoViewSense”:“Off”,and  
“Sound”-“PowerSave”:“SoundOff”)  
PowerOff  
0.3Worless  
MainPowerOff  
0W  
InputSignalConnector  
D-Submini15-pin  
DVI-Dconnector(ApplicabletoHDCP)  
DisplayPort(StandardV1.1a,applicabletoHDCP)  
ApplicableFormat(Audiosignal)  
- 2chlinearPCM  
 (32kHz/44.1kHz/48kHz/88.2kHz/96kHz)  
AnalogInputSignal(Sync)  
AnalogInputSignal(Video)  
Separate,TTL,positive/negative  
Analog,Positive(0.7Vp-p/75Ω)  
DigitalSignal(DVI)TransmissionSystem TMDS(SingleLink)  
AudioOutput  
Speakeroutput:1.0W+1.0W(8Ω,THD+N:10%orless)  
Headphoneoutput:2mW+2mW(32Ω,THD+N:3%orless)  
LineInput  
Inputimpedance:44kΩ(typ.)  
Inputlevel:2.0Vrms(Max.)  
Plug&Play  
Analog/Digital(DVI-D):VESADDC2B/EDIDstructure1.3  
Digital(DisplayPort):VESADisplayPort/EDIDstructure1.4  
Dimensions  
(Width)×  
(Height)×  
(Depth)  
Mainunit(FlexStand2) 540mm(21.3inch)×360-513.5mm(14.2inch-20.2inch)×245.5mm  
(9.7inch)  
Mainunit(TriStand2)  
540mm(21.3inch)×387.5-447.5mm(15.3inch-17.6inch)×200mm  
(7.9inch)  
Mainunit(without  
stand)  
540mm(21.3inch)×317.5mm(12.5inch)×56mm(2.2inch)  
Mass  
Mainunit(FlexStand2) Approx.6.3kg(13.9lbs.)  
Mainunit(TriStand2)  
Approx.4.9kg(10.8lbs.)  
Approx.3.7kg(8.2lbs.)  
Mainunit(without  
stand)  
Movablerange FlexStand2  
Tilt:  
30˚Up,0˚Down  
Swivel:  
172˚Right,172˚Left  
Adjustableheight:  
195mm(7.7inch)(179mm(7.0inch)fortiltof  
0˚)  
Rotation:  
Tilt:  
90˚(Clockwise)  
TriStand2  
25˚Up,0˚Down  
Swivel:  
172˚Right,172˚Left  
60mm(2.36inch)  
Adjustableheight:  
Operating:  
Environmental Temperature  
Conditions  
5˚Cto35˚C(41˚Fto95˚F)  
-20˚Cto60˚C(-4˚Fto140˚F)  
Transportation/  
Storage:  
Humidity  
Operating:  
20%to80%R.H.(nocondensation)  
10%to90%R.H.(nocondensation)  
Transportation/  
Storage:  
AirPressure  
Operating:  
700to1,060hPa  
200to1,060hPa  
Transportation/  
Storage:  
USB  
Standard  
Port  
USBSpecificationRevision2.0  
Upstreamport×1,Downstreamport×2  
CommunicationSpeed 480Mbps(high),12Mbps(full),1.5Mbps(low)  
Supplycurrent Downstream: Max.500mA/1port  
Chapter6Reference  
56  
EV2416W  
●
LCDPanel  
Size  
24.1-inch(610mm)  
Type  
TFTcolorLCD,LEDbacklight  
Anti-GlareHardCoating  
Horizontal170˚,vertical160˚(CR≥10)  
0.270mm  
Surfacetreatment  
Viewingangles  
DotPitch  
ResponseTime  
Black-white-black:Approx.5ms  
31-76kHz  
HorizontalScan Analog  
Frequency  
Digital  
DVI  
31-76kHz  
DisplayPort 31-76kHz  
55-61Hz(non-interlace)  
59-61Hz(non-interlace)  
VerticalScan  
Frequency  
Analog  
Digital  
DVI  
DisplayPort 59-61Hz(non-interlace)  
1920Dots×1200Lines  
193.3MHz  
Resolution  
Max.DotClock Analog  
Digital  
DVI  
DisplayPort 162MHz  
Approx.16.77millioncolors  
162MHz  
Max.DisplayColor  
DisplayArea(H×V)  
PowerSupply  
518.4mm×324.0mm(20.4inch×12.8inch)  
100-120VAC±10%,50/60Hz0.8A  
200-240VAC±10%,50/60Hz0.5A  
Power  
ScreenDisplayOn  
40Worless  
Consumption  
Powersavingmode  
0.3Worless (withnoUSBconnections,“EcoViewSense”:“Off”,and  
“Sound”-“PowerSave”:“SoundOff”)  
PowerOff  
0.3Worless  
MainPowerOff  
0W  
InputSignalConnector  
D-Submini15-pin  
DVI-Dconnector(ApplicabletoHDCP)  
DisplayPort(StandardV1.1a,applicabletoHDCP)  
ApplicableFormat(Audiosignal)  
- 2chlinearPCM  
 (32kHz/44.1kHz/48kHz/88.2kHz/96kHz)  
AnalogInputSignal(Sync)  
AnalogInputSignal(Video)  
Separate,TTL,positive/negative  
Analog,Positive(0.7Vp-p/75Ω)  
DigitalSignal(DVI)TransmissionSystem TMDS(SingleLink)  
AudioOutput  
Speakeroutput:1.0W+1.0W(8Ω,THD+N:10%orless)  
Headphoneoutput:2mW+2mW(32Ω,THD+N:3%orless)  
LineInput  
Inputimpedance:44kΩ(typ.)  
Inputlevel:2.0Vrms(Max.)  
Plug&Play  
Analog/Digital(DVI-D):VESADDC2B/EDIDstructure1.3  
Digital(DisplayPort):VESADisplayPort/EDIDstructure1.4  
Dimensions  
(Width)×  
(Height)×  
(Depth)  
Mainunit(FlexStand2) 552.5mm(21.8inch)×376-534mm(14.8-21.0inch)×245.5mm(9.7  
inch)  
Mainunit(TriStand2)  
552.5mm(21.8inch)×408-468mm(16.1-18.4inch)×200mm(7.9  
inch)  
Mainunit(without  
stand)  
552.5mm(21.8inch)×358mm(14.1inch)×57mm(2.24inch)  
Mass  
Mainunit(FlexStand2) Approx.6.3kg(13.9lbs.)  
Mainunit(TriStand2)  
Approx.4.9kg(10.8lbs.)  
Approx.3.7kg(8.2lbs.)  
Mainunit(without  
stand)  
Chapter6Reference  
57  
 
Movablerange FlexStand2  
Tilt:  
30˚Up,0˚Down  
Swivel:  
172˚Right,172˚Left  
Adjustableheight:  
195mm(7.7inch)(158mm(6.2inch)fortiltof  
0˚)  
Rotation:  
Tilt:  
90˚(Clockwise)  
TriStand2  
25˚Up,0˚Down  
Swivel:  
172˚Right,172˚Left  
60mm(2.36inch)  
Adjustableheight:  
Operating:  
Environmental Temperature  
Conditions  
5˚Cto35˚C(41˚Fto95˚F)  
-20˚Cto60˚C(-4˚Fto140˚F)  
Transportation/  
Storage:  
Humidity  
Operating:  
20%to80%R.H.(nocondensation)  
10%to90%R.H.(nocondensation)  
Transportation/  
Storage:  
AirPressure  
Operating:  
700to1,060hPa  
200to1,060hPa  
Transportation/  
Storage:  
USB  
Standard  
Port  
USBSpecificationRevision2.0  
Upstreamport×1,Downstreamport×2  
CommunicationSpeed 480Mbps(high),12Mbps(full),1.5Mbps(low)  
Supplycurrent  
Downstream:  
Max.500mA/1port  
EV2436W  
●
LCDPanel  
Size  
24.1-inch(610mm)  
Type  
TFTcolorLCD,LEDbacklight  
Anti-GlareHardCoating  
Surfacetreatment  
Viewingangles  
DotPitch  
Horizontal178˚,vertical178˚(CR≥10)  
0.270mm  
ResponseTime  
Black-white-black:Approx.14ms  
Gray-to-gray:Approx.6ms(Overdrivesetting:Enhanced)  
31-81kHz  
HorizontalScan Analog  
Frequency  
Digital  
DVI  
31-76kHz  
DisplayPort 31-76kHz  
55-76Hz(non-interlace)(WUXGA:-61Hz)  
59-61Hz(non-interlace)(VGATEXT:69-71Hz)  
VerticalScan  
Frequency  
Analog  
Digital  
DVI  
DisplayPort 59-61Hz(non-interlace)(VGATEXT:69-71Hz)  
Resolution  
1920Dots×1200Lines  
193.3MHz  
Max.DotClock Analog  
Digital  
DVI  
DisplayPort 162MHz  
Approx.16.77millioncolors  
162MHz  
Max.DisplayColor  
DisplayArea(H×V)  
PowerSupply  
518.4mm×324.0mm(20.4inch×12.8inch)  
100-120VAC±10%,50/60Hz1.0A  
200-240VAC±10%,50/60Hz0.6A  
Power  
ScreenDisplayOn  
60Worless  
Consumption  
Powersavingmode  
0.3Worless (withnoUSBconnections,“EcoViewSense”:“Off”,and  
“Sound”-“PowerSave”:“SoundOff”)  
PowerOff  
0.3Worless  
0W  
MainPowerOff  
Chapter6Reference  
58  
 
InputSignalConnector  
D-Submini15-pin  
DVI-Dconnector(ApplicabletoHDCP)  
DisplayPort(StandardV1.1a,applicabletoHDCP)  
ApplicableFormat(Audiosignal)  
- 2chlinearPCM  
 (32kHz/44.1kHz/48kHz/88.2kHz/96kHz)  
AnalogInputSignal(Sync)  
AnalogInputSignal(Video)  
Separate,TTL,positive/negative  
Analog,Positive(0.7Vp-p/75Ω)  
DigitalSignal(DVI)TransmissionSystem TMDS(SingleLink)  
AudioOutput  
Speakeroutput:1.0W+1.0W(8Ω,THD+N:10%orless)  
Headphoneoutput:2mW+2mW(32Ω,THD+N:3%orless)  
LineInput  
Inputimpedance:44kΩ(typ.)  
Inputlevel:2.0Vrms(Max.)  
Plug&Play  
Analog/Digital(DVI-D):VESADDC2B/EDIDstructure1.3  
Digital(DisplayPort):VESADisplayPort/EDIDstructure1.4  
Dimensions  
(Width)×  
(Height)×  
(Depth)  
Mainunit(FlexStand2) 552.5mm(21.8inch)×376-534mm(14.8-21.0inch)×245.5mm(9.7  
inch)  
Mainunit(TriStand2)  
552.5mm(21.8inch)×408-468mm(16.1-18.4inch)×200mm(7.9  
inch)  
Mainunit(without  
stand)  
552.5mm(21.8inch)×358mm(14.1inch)×57mm(2.24inch)  
Mass  
Mainunit(FlexStand2) Approx.6.7kg(14.8lbs.)  
Mainunit(TriStand2)  
Approx.5.3kg(11.7lbs.)  
Approx.4.1kg(9lbs.)  
Mainunit(without  
stand)  
Movablerange FlexStand2  
Tilt:  
30˚Up,0˚Down  
Swivel:  
172˚Right,172˚Left  
Adjustableheight:  
195mm(7.7inch)(158mm(6.2inch)fortiltof  
0˚)  
Rotation:  
Tilt:  
90˚(Clockwise)  
TriStand2  
25˚Up,0˚Down  
Swivel:  
172˚Right,172˚Left  
60mm(2.36inch)  
Adjustableheight:  
Operating:  
Environmental Temperature  
Conditions  
5˚Cto35˚C(41˚Fto95˚F)  
-20˚Cto60˚C(-4˚Fto140˚F)  
Transportation/  
Storage:  
Humidity  
Operating:  
20%to80%R.H.(nocondensation)  
10%to90%R.H.(nocondensation)  
Transportation/  
Storage:  
AirPressure  
Operating:  
700to1,060hPa  
200to1,060hPa  
Transportation/  
Storage:  
USB  
Standard  
Port  
USBSpecificationRevision2.0  
Upstreamport×1,Downstreamport×2  
CommunicationSpeed 480Mbps(high),12Mbps(full),1.5Mbps(low)  
Supplycurrent Downstream: Max.500mA/1port  
Chapter6Reference  
59  
Main Default Settings  
●
●
AutoEcoView  
EcoViewOptimizer2  
EcoViewSense  
FineContrastMode  
ScreenSize  
Standard  
On  
Off  
User1  
FullScreen  
3
Smoothing  
PowerSave  
On  
EcoTimer  
Off  
Language  
English  
Center  
Manual  
MenuPosition  
InputSignal  
Outside Dimensions  
EV2316W / EV2336W  
FlexStand2  
Unit:mm(inch)  
349 (13.7)  
315 (12.4)  
172°  
SWIVEL  
540 (21.3)  
511.8 (20.1)  
14.1 (0.56)  
100 (3.9)  
220 (8.7)  
220 (8.7)  
234 (9.2)  
TILT  
30°  
PIVOT  
30°  
23 (0.91)  
268.5 (10.6)  
28.5 (1.12)  
60.5 (2.38)  
209 (8.2)  
245.5 (9.7)  
Chapter6Reference  
60  
   
TriStand2  
Unit:mm(inch)  
349 (13.7)  
315 (12.4)  
SWIVEL  
155.5 (6.1)  
130.5 (5.1)  
69.5 (2.74)  
540 (21.3)  
511.8 (20.1)  
14.1 (0.56)  
100 (3.9)  
220 (8.7)  
220 (8.7)  
TILT  
113.5 (4.5)  
92.5 (3.64)  
20 (0.79)  
46 (1.81)  
200 (7.9)  
EV2416W / EV2436W  
FlexStand2  
Unit:mm(inch)  
349 (13.7)  
315 (12.4)  
172°  
SWIVEL  
552.5 (21.8)  
520.4 (20.5)  
16.05 (0.63)  
245 (9.6)  
100 (3.9)  
226.25 (8.9)  
226.25 (8.9)  
TILT  
PIVOT  
20.5°  
31.5 (1.24)  
59.5 (2.34)  
34 (1.34)  
279 (11.0)  
209 (8.2)  
245.5 (9.7)  
Chapter6Reference  
61  
TriStand2  
Unit:mm(inch)  
349 (13.7)  
315 (12.4)  
SWIVEL  
176 (6.9)  
142 (5.6)  
70.5 (2.78)  
TILT  
552.5 (21.8)  
520.4 (20.5)  
100 (3.9)  
226.25 (8.9)  
16.05 (0.63)  
226.25 (8.9)  
92.5 (3.64)  
113.5 (4.5)  
11 (0.43)  
45 (1.77)  
200 (7.9)  
Accessories  
●
Signalcable  
CleaningKit  
MD-C87  
EIZO“ScreenCleaner”  
For the latest information about the accessories, refer to our web site.  
http://www.eizo.com  
Chapter6Reference  
62  
 
6-8. Preset Timing  
The following table shows factory preset analog signal timing.  
Attention  
• Display position may be deviated depending on the PC connected, which may require screen adjustment using Setting menu.  
• If a signal other than those listed in the table is input, adjust the screen using the Setting menu. However, screen display may  
still be incorrect even after the adjustment.  
• When interlace signals are used, the screen cannot be displayed correctly even after screen adjustment using the Setting  
menu.  
EV2316W  
●
Frequency  
Polarity  
Vertical: Hz Horizontal Vertical  
Applicable  
Signals  
Resolution  
Dot Clock:  
MHz  
Horizontal:  
kHz  
640×480  
800×600  
VGA  
VESA  
VESA  
CEA-861  
VESA  
VESA  
25.18  
40.00  
65.00  
31.47  
37.88  
48.36  
45.00  
60.00  
63.98  
65.29  
64.67  
67.50  
59.94  
60.32  
60.00  
60.00  
60.00  
60.02  
59.95  
59.88  
60.00  
Negative  
Positive  
Negative  
Positive  
Positive  
Positive  
Negative  
Positive  
Positive  
Negative  
Positive  
Negative  
Positive  
Positive  
Positive  
Positive  
Negative  
Positive  
1024×768  
1280×720  
1280×960  
1280×1024  
1680×1050  
1680×1050  
1920×1080  
74.25  
108.00  
108.00  
146.25  
119.00  
148.50  
VESACVT  
VESACVTRB  
CEA-861  
EV2336W  
●
Frequency  
Polarity  
Applicable  
Signals  
Resolution  
Dot Clock:  
MHz  
Horizontal:  
kHz  
Vertical: Hz Horizontal  
Vertical  
640×480  
640×480  
640×480  
720×400  
VGA  
VESA  
VESA  
25.18  
31.50  
31.50  
31.47  
37.86  
37.50  
31.47  
35.16  
37.88  
48.08  
46.88  
48.36  
56.48  
60.02  
45.00  
60.00  
63.98  
79.98  
65.29  
64.67  
67.50  
59.94  
72.81  
75.00  
70.09  
56.25  
60.32  
72.19  
75.00  
60.00  
70.07  
75.03  
60.00  
60.00  
60.02  
75.03  
59.95  
59.88  
60.00  
Negative  
Negative  
Negative  
Negative  
Positive  
Positive  
Positive  
Positive  
Negative  
Negative  
Positive  
Positive  
Positive  
Positive  
Positive  
Negative  
Positive  
Positive  
Negative  
Negative  
Negative  
Positive  
Positive  
Positive  
Positive  
Positive  
Negative  
Negative  
Positive  
Positive  
Positive  
Positive  
Positive  
Positive  
Negative  
Positive  
VGATEXT  
VESA  
28.32  
36.00  
40.00  
50.00  
49.50  
65.00  
75.00  
78.75  
74.25  
108.00  
108.00  
135.00  
146.25  
119.00  
148.50  
800×600  
800×600  
800×600  
800×600  
1024×768  
1024×768  
1024×768  
1280×720  
1280×960  
1280×1024  
1280×1024  
1680×1050  
1680×1050  
1920×1080  
VESA  
VESA  
VESA  
VESA  
VESA  
VESA  
CEA-861  
VESA  
VESA  
VESA  
VESACVT  
VESACVTRB  
CEA-861  
Chapter6Reference  
63  
 
EV2416W  
●
Frequency  
Polarity  
Vertical: Hz Horizontal Vertical  
Applicable  
Signals  
Resolution  
Dot Clock:  
MHz  
Horizontal:  
kHz  
640×480  
800×600  
VGA  
VESA  
VESA  
CEA-861  
VESA  
VESA  
25.18  
40.00  
65.00  
31.47  
37.88  
48.36  
45.00  
60.00  
63.98  
75.00  
65.29  
64.67  
74.56  
74.04  
59.94  
60.32  
60.00  
60.00  
60.00  
60.02  
60.00  
59.95  
59.88  
59.89  
59.95  
Negative  
Positive  
Negative  
Positive  
Positive  
Positive  
Positive  
Negative  
Positive  
Negative  
Positive  
Negative  
Positive  
Negative  
Positive  
Positive  
Positive  
Positive  
Positive  
Negative  
Positive  
Negative  
1024×768  
1280×720  
1280×960  
1280×1024  
1600×1200  
1680×1050  
1680×1050  
1920×1200  
1920×1200  
74.25  
108.00  
108.00  
162.00  
146.25  
119.00  
193.25  
154.00  
VESA  
VESACVT  
VESACVTRB  
VESACVT  
VESACVTRB  
EV2436W  
●
Frequency  
Polarity  
Applicable  
Signals  
Resolution  
Dot Clock:  
MHz  
Horizontal:  
kHz  
Vertical: Hz Horizontal  
Vertical  
640×480  
640×480  
640×480  
720×400  
800×600  
800×600  
800×600  
800×600  
1024×768  
1024×768  
1024×768  
1280×720  
1280×960  
1280×1024  
1280×1024  
1600×1200  
1680×1050  
1680×1050  
1920×1200  
1920×1200  
VGA  
VESA  
VESA  
25.18  
31.50  
31.50  
31.47  
37.86  
37.50  
31.47  
35.16  
37.88  
48.08  
46.88  
48.36  
56.48  
60.02  
45.00  
60.00  
63.98  
79.98  
75.00  
65.29  
64.67  
74.56  
74.04  
59.94  
72.81  
75.00  
70.09  
56.25  
60.32  
72.19  
75.00  
60.00  
70.07  
75.03  
60.00  
60.00  
60.02  
75.03  
60.00  
59.95  
59.88  
59.89  
59.95  
Negative  
Negative  
Negative  
Negative  
Positive  
Positive  
Positive  
Positive  
Negative  
Negative  
Positive  
Positive  
Positive  
Positive  
Positive  
Positive  
Negative  
Positive  
Negative  
Positive  
Negative  
Negative  
Negative  
Positive  
Positive  
Positive  
Positive  
Positive  
Negative  
Negative  
Positive  
Positive  
Positive  
Positive  
Positive  
Positive  
Positive  
Negative  
Positive  
Negative  
VGATEXT  
VESA  
28.32  
36.00  
40.00  
50.00  
49.50  
65.00  
75.00  
78.75  
VESA  
VESA  
VESA  
VESA  
VESA  
VESA  
CEA-861  
VESA  
VESA  
74.25  
108.00  
108.00  
135.00  
162.00  
146.25  
119.00  
193.25  
154.00  
VESA  
VESA  
VESACVT  
VESACVTRB  
VESACVT  
VESACVTRB  
Chapter6Reference  
64  
 
6-9. Glossary  
Clock  
The analog signal input monitor needs to reproduce a clock of the same frequency as the dot clock of the  
graphics system in use, when the analog signal is converted to a digital signal for image display. This is  
called clock adjustment. If the clock pulse is not set correctly, some vertical bars appear on the screen.  
DDC/CI (Display Data Channel / Command Interface)  
VESA provides the standardization for the interactive communication of the setting information, etc.  
between a PC and the monitor.  
DisplayPort  
DisplayPort is a next-generation digital AV interface that allows connection of the PC, audio, imaging  
devices, etc. to the monitor. One cable can transfer sound with images.  
DVI (Digital Visual Interface)  
DVI is a digital interface standard. DVI allows direct transmission of the PC’s digital data without loss.  
This adopts the TMDS transmission system and DVI connectors. There are two types of DVI connectors.  
One is a DVI-D connector for digital signal input only. The other is a DVI-I connector for both digital and  
analog signal inputs.  
DVI DMPM (DVI Digital Monitor Power Management)  
DVI DMPM is a digital interface power saving function. The “Monitor ON (operating mode)” and “Active  
Off (power saving mode)” are indispensable for DVI DMPM as the monitor’s power mode.  
Gain  
This is used to adjust each color parameter for red, green and blue. An LCD monitor displays the color by  
the light passing through the panel color filter. Red, green and blue are the three primary colors. All the  
colors on the screen are displayed by combining these three colors. The color tone can be changed by  
adjusting the light intensity (volume) passing through each color’s filter.  
Gamma  
Generally, the monitor brightness varies nonlinearly with the input signal level, which is called “Gamma  
Characteristic”. A small gamma value produces a low-contrast image, while a large gamma value produces a  
high-contrast image.  
HDCP (High-bandwidth Digital Content Protection)  
Digital signal coding system developed to copy-protect the digital contents, such as video, music, etc.  
This helps to transmit the digital contents safely by coding the digital contents sent via the DVI or HDMI  
connector on the output side and decoding them on the input side.  
Any digital contents cannot be reproduced if both of the equipments on the output and input sides are not  
applicable to HDCP system.  
Chapter6Reference  
65  
   
Overdrive  
This technology enhances response speed by increasing the potential difference at the time of motion of  
liquid-crystal pixels, and it is used for liquid-crystal TV sets and others in general. It provides clear-cut  
three-dimensional display with little afterimage, by improving response speed of the intermediate graduation  
range that frequently appears in moving images.  
Phase  
Phase means the sampling timing to convert the analog input signal to a digital signal. Phase adjustment is  
made to adjust the timing. It is recommended that phase adjustment be made after the clock is adjusted  
correctly.  
Range Adjustment  
Range adjustment controls the signal output levels to display every color gradation. It is recommended that  
range adjustment be made before color adjustment.  
Resolution  
The LCD panel consists of numerous pixels of specified size, which are illuminated to form images. This  
monitor consists of horizontal 1920 pixels and 1080 vertical pixels (EV2316W / EV2336W), or horizontal  
1920 pixels and 1200 vertical pixels (EV2416W / EV2436W). At a resolution of 1920 × 1080 (EV2316W /  
EV2336W) or 1920 × 1200 (EV2416W / EV2436W), all pixels are illuminated as a full screen (1:1).  
sRGB (Standard RGB)  
International standard for color reproduction and color space among peripheral devices (such as monitors,  
printers, digital cameras, scanners). As a form of simple color matching for the Internet, colors can be  
displayed using tones close to those of the transmission and reception devices.  
Temperature  
Color temperature is a method to measure the white color tone, generally indicated in degrees Kelvin. The  
screen becomes reddish at a low temperature, and bluish at a high temperature, like the flame temperature.  
5000 K: Slightly reddish white  
6500 K: White referred to as daylight-balanced color  
9300 K: Slightly bluish white  
TMDS (Transition Minimized Differential Signaling)  
A signal transmission system for digital interface.  
VESA DPM (Video Electronics Standards Association - Display Power  
Management)  
VESA specifications achieve increased energy efficiency for computer monitors. This involves  
standardization of signals sent from the computer (graphics board).  
DPM defines the status of signals transmitted between the computer and monitor.  
Chapter6Reference  
66  
Appendix  
Trademark  
The DisplayPort Compliance Logo and VESA are registered trademarks of the Video Electronics Standards  
Association.  
Windows, Windows Vista, Windows Media, SQL Server, and Xbox 360 are registered trademarks of Microsoft  
Corporation in the United States and other countries.  
Apple, Mac, Macintosh, iMac, eMac, Mac OS, MacBook, PowerBook, ColorSync, QuickTime, and iBook are  
registered trademarks of Apple Inc.  
Acrobat, Adobe, Adobe AIR, and Photoshop are registered trademarks of Adobe Systems Incorporated in the  
United States and other countries.  
PowerPC is a registered trademark of International Business Machines Corporation.  
Pentium is a registered trademark of Intel Corporation in the United States and other countries.  
AMD Athlon and AMD Opteron are trademarks of Advanced Micro Devices, Inc.  
GRACoL and IDEAlliance are registered trademarks of International Digital Enterprise Alliance.  
ColorVision, ColorVision Spyder2 are registered trademarks of DataColor Holding AG.  
Spyder3 is a trademark of DataColor Holding AG.  
Eye-One, ColorMunki, and X-Rite are registered trademarks or trademarks of X-Rite Incorporated.  
TouchWare is a trademark of 3M Touch Systems, Inc.  
NextWindow is a registered trademark of NextWindow Ltd.  
RealPlayer is a registered trademark of RealNetworks, Inc.  
NEC is a registered trademark of NEC Corporation. PC-9801 and PC-9821 are trademarks of NEC Corporation.  
PlayStation is a registered trademark of Sony Computer Entertainment Inc.  
PSP and PS3 are trademarks of Sony Computer Entertainment Inc.  
ENERGY STAR is a registered trademark of the United States Environmental Protection Agency in the United  
States and other countries.  
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or  
registered trademarks of HDMI Licensing, LLC in the United States and other countries.  
Kensington and MicroSaver are trademarks of ACCO Brands Corporation.  
EIZO, the EIZO Logo, ColorEdge, DuraVision, FlexScan, FORIS, RadiForce, RadiCS, RadiNET, Raptor, and  
ScreenManager are registered trademarks of EIZO Corporation in Japan and other countries.  
ColorNavigator, EIZO EasyPIX, EcoView NET, EIZO ScreenSlicer, i•Sound, Screen Administrator, and UniColor  
Pro are trademarks of EIZO Corporation.  
All other company and product names are trademarks or registered trademarks of their respective owners.  
License  
A round gothic bold bit map font designed by Ricoh is used for the characters displayed on this product.  
Appendix  
67  
 
ENERGY STAR  
As an ENERGY STAR Partner, EIZO Corporation has determined that this product meets the  
ENERGY STAR guidelines for energy efficiency.  
TCO  
This product has acquired the TCO standard that relates to the safety, ergonomics (EcoView Optimizer 2: Off),  
environment and so forth of office equipment. For an overview of the TCO, refer to our web site.  
http://www.eizo.com  
Appendix  
68  
 
FCC Declaration of Conformity  
For U.S.A. , Canada, etc. (rated 100-120 Vac) Only  
FCC Declaration of Conformity  
We, the Responsible Party  
EIZOInc.  
5710WarlandDrive,Cypress,CA90630  
Phone:(562)431-5011  
declare that the product  
Tradename:EIZO  
Model:FlexScanEV2316W/EV2336W/EV2416W/EV2436W  
is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the following  
two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any  
interference received, including interference that may cause undesired operation.  
ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,pursuant  
toPart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainst  
harmfulinterferenceinaresidentialinstallation.Thisequipmentgenerates,uses,andcanradiateradio  
frequencyenergyand,ifnotinstalledandusedinaccordancewiththeinstructions,maycauseharmful  
interferencetoradiocommunications.However,thereisnoguaranteethatinterferencewillnotoccurin  
aparticularinstallation.Ifthisequipmentdoescauseharmfulinterferencetoradioortelevisionreception,  
whichcanbedeterminedbyturningtheequipmentoffandon,theuserisencouragedtotrytocorrect  
theinterferencebyoneormoreofthefollowingmeasures.  
* Reorientorrelocatethereceivingantenna.  
* Increasetheseparationbetweentheequipmentandreceiver.  
* Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected.  
* Consultthedealeroranexperiencedradio/TVtechnicianforhelp.  
Changesormodi cationsnotexpresslyapprovedbythepartyresponsibleforcompliancecouldvoidthe  
user’sauthoritytooperatetheequipment.  
Note  
Usetheattachedspeci edcablebeloworEIZOsignalcablewiththismonitorsoastokeepinterference  
withinthelimitsofaClassBdigitaldevice.  
- ACCord  
- ShieldedSignalCable(enclosed)  
Canadian Notice  
ThisClassBdigitalapparatuscomplieswithCanadianICES-003.  
CetappareilnumériquedeleclasseBestcomformeàlanormeNMB-003duCanada.  
Appendix  
69  
 
Hinweise zur Auswahl des richtigen Schwenkarms für Ihren Monitor  
Dieser Monitor ist für Bildschirmarbeitsplätze vorgesehen. Wenn nicht der zum Standardzubehör gehörige  
Schwenkarm verwendet wird, muss statt dessen ein geeigneter anderer Schwenkarm installiert werden. Bei der  
Auswahl des Schwenkarms sind die nachstehenden Hinweise zu berücksichtigen:  
Der Standfuß muß den nachfolgenden Anforderungen entsprechen:  
a)Der Standfuß muß eine ausreichende mechanische Stabilität zur Aufnahme des Gewichtes vom Bildschirmgerät  
und des spezifizierten Zubehörs besitzen. Das Gewicht des Bildschirmgerätes und des Zubehörs sind in der  
zugehörenden Bedienungsanleitung angegeben.  
b)Die Befestigung des Standfusses muß derart erfolgen, daß die oberste Zeile der Bildschirmanzeige nicht höher  
als die Augenhöhe eines Benutzers in sitzender Position ist.  
c)Im Fall eines stehenden Benutzers muß die Befestigung des Bildschirmgerätes derart erfolgen, daß die Höhe der  
Bildschirmmitte über dem Boden zwischen 135 – 150 cm beträgt.  
d)Der Standfuß muß die Möglichkeit zur Neigung des Bildschirmgerätes besitzen (max. vorwärts: 5°, min. nach  
hinten ≥ 5°).  
e)Der Standfuß muß die Möglichkeit zur Drehung des Bildschirmgerätes besitzen (max. ±180°). Der maximale  
Kraftaufwand dafür muß weniger als 100 N betragen.  
f) Der Standfuß muß in der Stellung verharren, in die er manuell bewegt wurde.  
g)Der Glanzgrad des Standfusses muß weniger als 20 Glanzeinheiten betragen (seidenmatt).  
h)Der Standfuß mit Bildschirmgerät muß bei einer Neigung von bis zu 10° aus der normalen aufrechten Position  
kippsicher sein.  
Hinweis zur Ergonomie :  
Dieser Monitor erfüllt die Anforderungen an die Ergonomie nach EK1-ITB2000 mit dem Videosignal, 1920×1080  
(EV2316W / EV2336W) / 1920×1200 (EV2416W / EV2436W), Digital Eingang und mindestens 60,0 Hz  
Bildwiederholfrequenz, non interlaced. Weiterhin wird aus ergonomischen Gründen empfohlen, die Grundfarbe  
Blau nicht auf dunklem Untergrund zu verwenden (schlechte Erkennbarkeit, Augenbelastung bei zu geringem  
Zeichenkontrast.)  
Übermäßiger Schalldruck von Ohrhörern bzw. Kopfhörern kann einen Hörverlust bewirken.  
Eine Einstellung des Equalizers auf Maximalwerte erhöht die Ausgangsspannung am Ohrhörer- bzw.  
Kopfhörerausgang und damit auch den Schalldruckpegel.  
„Maschinenlärminformations-Verordnung 3. GPSGV:  
Der höchste Schalldruckpegel beträgt 70 dB(A) oder weniger gemäss EN ISO 7779“  
[Begrenzung des maximalen Schalldruckpegels am Ohr]  
Bildschirmgeräte: Größte Ausgangsspannung 150 mV  
Appendix  
70  
 
LIMITED WARRANTY  
LIMITED WARRANTY  
EIZOCorporation(hereinafterreferredtoas“EIZO”)anddistributorsauthorizedbyEIZO(hereinafterreferredtoasthe  
“Distributors”)warrant,subjecttoandinaccordancewiththetermsofthislimitedwarranty(hereinafterreferredtoasthe  
“Warranty”),totheoriginalpurchaser(hereinafterreferredtoasthe“Original Purchaser”)whopurchasedtheproduct  
speci edinthisdocument(hereinafterreferredtoasthe“Product”)fromEIZOorDistributors,thatEIZOandDistributors  
shall,attheirsolediscretion,eitherrepairorreplacetheProductatnochargeiftheOriginalPurchaserbecomesaware  
withintheWarrantyPeriod(de nedbelow)thattheProductmalfunctionsorisdamagedinthecourseofnormaluseof  
theProductinaccordancewiththedescriptionintheinstructionmanualattachedtotheProduct(hereinafterreferredto  
asthe“User’s Manual”).  
TheperiodofthisWarrantyislimitedto(i)five(5)yearsfromthedateofpurchaseoftheProduct;or,limitedtothe  
expirationof(ii)30,000hoursofitsuseoftheProduct(hereinafterreferredtoasthe“Warranty Period”).EIZOand  
DistributorsshallbearnoliabilityorobligationwithregardtotheProductinrelationtotheOriginalPurchaseroranythird  
partiesotherthanasprovidedunderthisWarranty.  
EIZOandDistributorswillceasetoholdorstoreanypartsoftheProductuponexpirationofseven(7)yearsafterthe  
productionofsuchpartsisdiscontinued.Inrepairingthemonitor,EIZOandDistributorswilluserenewalpartswhich  
complywithourQCstandards.  
TheWarrantyisvalidonlyinthecountriesorterritorieswheretheDistributorsarelocated.TheWarrantydoesnotrestrict  
anylegalrightsoftheOriginalPurchaser.  
NotwithstandinganyotherprovisionofthisWarranty,EIZOandDistributorsshallhavenoobligationunderthisWarranty  
whatsoeverinanyofthecasesassetforthbelow:  
(a) AnydefectoftheProductcausedbyfreightdamage,modi cation,alteration,abuse,misuse,accident,incorrect  
installation,disaster,faultymaintenanceand/orimproperrepairbythirdpartyotherthanEIZOandDistributors;  
(b) AnyincompatibilityoftheProductduetopossibletechnicalinnovationsand/orregulations;  
(c) Anydeteriorationofthesensor;  
(d) AnydeteriorationofdisplayperformancecausedbythedeteriorationofexpendablepartssuchastheLCDpanel  
and/orbacklight,etc.(e.g.changesinbrightness,changesinbrightnessuniformity,changesincolor,changesin  
coloruniformity,defectsinpixelsincludingburntpixels,etc.);  
(e) AnydefectoftheProductcausedbyexternalequipment;  
(f) AnydefectoftheProductonwhichtheoriginalserialnumberhasbeenalteredorremoved;  
(g) Anynormaldeteriorationoftheproduct,particularlythatofconsumables,accessories,and/orattachments(e.g.  
buttons,rotatingparts,cables,User’sManual,etc.);and  
(h) Anydeformation,discoloration,and/orwarpoftheexterioroftheproductincludingthatofthesurfaceoftheLCD  
panel.  
ToobtainserviceundertheWarranty,theOriginalPurchasermustdelivertheProduct,freightprepaid,initsoriginal  
packageorotheradequatepackageaffordinganequaldegreeofprotection,assumingtheriskofdamageand/orloss  
intransit,tothelocalDistributor.TheOriginalPurchasermustpresentproofofpurchaseoftheProductandthedateof  
suchpurchasewhenrequestingservicesundertheWarranty.  
TheWarrantyPeriodforanyreplacedand/orrepairedproductunderthisWarrantyshallexpireattheendoftheoriginal  
WarrantyPeriod.  
EIZOORDISTRIBUTORSARENOTRESPONSIBLEFORANYDAMAGETO,ORLOSSOF,DATAOROTHER  
INFORMATIONSTOREDINANYMEDIAORANYPARTOFANYPRODUCTRETURNEDTOEIZOORDISTRIBUTORS  
FORREPAIR.  
EIZOANDDISTRIBUTORSMAKENOFURTHERWARRANTIES,EXPRESSEDORIMPLIED,WITHRESPECTTO  
THEPRODUCTANDITSQUALITY,PERFORMANCE,MERCHANTABILITYORFITNESSFORANYPARTICULAR  
USE.INNOEVENTSHALLEIZOORDISTRIBUTORSBELIABLEFORANYINCIDENTAL,INDIRECT,SPECIAL,  
CONSEQUENTIALOROTHERDAMAGEWHATSOEVER(INCLUDING,WITHOUTLIMITATION,DAMAGESFOR  
LOSSOFPROFIT,BUSINESSINTERRUPTION,LOSSOFBUSINESSINFORMATION,ORANYOTHERPECUNIARY  
LOSS)ARISINGOUTOFTHEUSEORINABILITYTOUSETHEPRODUCTORINANYCONNECTIONWITHTHE  
PRODUCT,WHETHERBASEDONCONTRACT,TORT,NEGLIGENCE,STRICTLIABILITYOROTHERWISE,EVEN  
IFEIZOORDISTRIBUTORSHAVEBEENADVISEDOFTHEPOSSIBILITYOFSUCHDAMAGES.THISEXCLUSION  
ALSOINCLUDESANYLIABILITYWHICHMAYARISEOUTOFTHIRDPARTYCLAIMSAGAINSTTHEORIGINAL  
PURCHASER.THEESSENCEOFTHISPROVISIONISTOLIMITTHEPOTENTIALLIABILITYOFEIZOAND  
DISTRIBUTORSARISINGOUTOFTHISLIMITEDWARRANTYAND/ORSALES.  
Appendix  
71  
 
BEGRENZTE GARANTIE  
EIZOCorporation(imWeiterenals„EIZO“bezeichnet)unddieVertragsimporteurevonEIZO(imWeiterenals  
„Vertrieb(e)“bezeichnet)garantierendemursprünglichenKäufer(imWeiterenals„Erstkäufer“bezeichnet),derdasin  
diesemDokumentvorgegebeneProdukt(imWeiterenals„Produkt“bezeichnet)vonEIZOodereinemVertrieberworben  
hat,gemäßdenBedingungendieserbeschränktenGarantie(imWeiterenals„Garantie“bezeichnet),dassEIZOund  
derVertriebnacheigenemErmessendasProduktentwederkostenlosreparierenoderaustauschen,fallsderErstkäufer  
innerhalbderGarantiefrist(weiteruntenfestgelegt)eineFehlfunktionbzw.BeschädigungdesProduktsfeststellt,  
diewährenddesnormalenGebrauchsdesProduktsgemäßdenAnweisungendeszumLieferumfangdesProdukts  
gehörendenBenutzerhandbuchs(imWeiterenals„Benutzerhandbuch“bezeichnet)aufgetretenist.  
DieDauerderGarantieleistungbeträgt(i)fünf(5)JahreabdemErstverkaufsdatumdesProduktsoder(ii)30.000  
BetriebsstundendesProdukts(imWeiterenals„Garantiefrist“bezeichnet).EIZOunddieVertriebeübernehmenüber  
denRahmendieserGarantiehinaushinsichtlichdesProduktskeinerleiHaftungoderVerp ichtungdemErstkäuferoder  
Drittengegenüber.  
EIZOunddieVertriebeverp ichtensich,ErsatzteilefürdasProduktübereinenZeitraumvonsieben(7)Jahrennach  
EinstellungderProduktionderErsatzteilezulagernbzw.anzubieten.EIZOundseineVertriebspartnerverp ichtensich,  
beieineretwaigenReparaturdesMonitorsausschließlichProduktegemäßdenEIZO-Qualitätssicherungsstandardszu  
verwenden.  
Diese Garantie gilt nur in Ländern oder Gebieten, in denen sich Vertriebe befinden. Die gesetzlichen  
GewährleistungsrechtedesErstkäufersgegenüberdemVerkäuferwerdendurchdieseGarantienichtberührt.  
EIZOunddieVertriebebesitzenimRahmendieserGarantiekeinerleiVerp ichtungindenfolgendenFällen:  
(a) Produktdefekte,dieaufFrachtschäden,Modifikation,Nachgestaltung,Missbrauch,Fehlbedienung,Unfälle,  
unsachgemäßeInstallation,Naturkatastrophen,fehlerhafteWartungund/oderunsachgemäßeReparaturdurcheine  
andereParteialsEIZOunddieVertriebezurückzuführensind.  
(b) EineInkompatibilitätdesProduktsaufgrundvontechnischenNeuerungenund/oderneuenBestimmungen,die  
nachdemKaufinKrafttreten.  
(c) JeglicheVerschlechterungdesSensors.  
(d) JeglicheVerschlechterungderBildschirmleistung,diedurchVerschleißteilewiedasLCD-Panelund/oderdie  
Hintergrundbeleuchtungusw.hervorgerufenwerden(z.B.VeränderungenvonHelligkeitoderHelligkeitsverteilung,  
VeränderungenvonFarbeoderFarbverteilung,PixeldefekteeinschließlichvondurchgebranntenPixelnusw.).  
(e) Produktdefekte,diedurchexterneGeräteverursachtwerden.  
(f) JeglicherDefekteinesProdukts,dessenursprünglicheSeriennummergeändertoderentferntwurde.  
(g) NormaleAbnutzungdesProdukts,insbesonderevonVerbrauchsteilen,Zubehörteilenund/oderBeilagen(z.B.  
Tasten,drehbareTeile,Kabel,Benutzerhandbuchusw.);sowie  
(h) Verformungen,Verfärbungenund/oderVerziehungenamProduktäußeren,einschließlichderOber ächedesLCD-  
Panels.  
BeiInanspruchnahmederGarantieleistungistderErstkäuferverpflichtet,dasProduktaufeigeneKostenund  
inderOriginalverpackungbzw.eineranderengeeignetenVerpackung,dieeinengleichwertigenSchutzgegen  
Transportschädenbietet,andenörtlichenVertriebzuübersenden,wobeiderErstkäuferdasTransportrisikogegenüber  
Schädenund/oderVerlustträgt.ZumZeitpunktderInanspruchnahmederGarantieleistungmussderErstkäufereinen  
Verkaufsbelegvorweisen,aufdemdasKaufdatumangegebenist.  
DieGarantiefristfüreinimRahmendieserGarantieausgetauschtesund/oderrepariertesProdukterlischtnachAblauf  
derursprünglichenGarantiefrist.  
EIZOODERDIEEIZO-VERTRAGSIMPORTEUREHAFTENNICHTFÜRZERSTÖRTEDATENBESTÄNDEODERDIE  
KOSTENDERWIEDERBESCHAFFUNGDIESERDATENBESTÄNDEAUFJEGLICHENDATENTRÄGERNODER  
TEILENDESPRODUKTS,DIEIMRAHMENDERGARANTIEBEIEIZOODERDENEIZO-VERTRAGSIMPORTEUREN  
ZURREPARATUREINGEREICHTWURDEN.  
EIZOUNDDIEEIZO-VERTRAGSIMPORTEUREGEBENWEDEREXPLIZITENOCHIMPLIZITEGARANTIEN  
INBEZUGAUFDIESESPRODUKTUNDSEINEQUALITÄT,LEISTUNG,VERKÄUFLICHKEITODEREIGNUNG  
FÜREINENBESTIMMTENZWECK.AUFKEINENFALLSINDEIZOODERDIEEIZO-VERTRAGSIMPORTEURE  
VERANTWORTLICHFÜRJEGLICHEZUFÄLLIGE,INDIREKTE,SPEZIELLE,FOLGE-ODERANDERESCHÄDEN  
JEGLICHERART(EINSCHLIESSLICHOHNEJEDEBEGRENZUNGSCHÄDENBEZÜGLICHPROFITVERLUST,  
GESCHÄFTSUNTERBRECHUNG,VERLUSTVONGESCHÄFTSINFORMATIONODERJEGLICHEANDEREN  
FINANZIELLENEINBUSSEN),DIEDURCHDIEVERWENDUNGDESPRODUKTESODERDIEUNFÄHIGKEIT  
ZURVERWENDUNGDESPRODUKTESODERINJEGLICHERBEZIEHUNGMITDEMPRODUKT,SEIES  
BASIERENDAUFVERTRAG,SCHADENSERSATZ,NACHLAESSIGKEIT,STRIKTEHAFTPFLICHTODERANDEREN  
FORDERUNGENENTSTEHEN,AUCHWENNEIZOUNDDIEEIZO-VERTRAGSIMPORTEUREIMVORAUSÜBER  
DIEMÖGLICHKEITSOLCHERSCHÄDENINFORMIERTWURDEN.DIESERAUSSCHLUSSENTHÄLTAUCHJEDE  
HAFTPFLICHT,DIEAUSFORDERUNGENDRITTERGEGENDENERSTKÄUFERENTSTEHENKANN.ZWECK  
DIESERKLAUSELISTES,DIEHAFTUNGVONEIZOUNDDENVERTRIEBENGEGENÜBERFORDERUNGENZU  
BEGRENZEN,DIEAUSDIESERBESCHRÄNKTENGARANTIEUND/ODERDEMVERKAUFENTSTEHENKÖNNEN.  
Appendix  
72  
GARANTIE LIMITÉE  
EIZOCorporation(ci-aprèsdénommé«EIZO »)etlesdistributeursautorisésparEIZO(ci-aprèsdénommés  
«Distributeurs »),sousréserveetconformémentauxtermesdecettegarantielimitée(ci-aprèsdénommée  
«Garantie »),garantissentàl’acheteurinitial(ci-aprèsdénommé«Acheteur initial »)duproduitspécifiédansla  
présente(ci-aprèsdénommé«Produit »)achetéauprèsd’EIZOoudeDistributeursagréésEIZO,queEIZOetses  
DistributeursaurontpouroptionderéparerouremplacergratuitementleProduitsil’Acheteurinitialconstate,pendantla  
Périodedegarantie(dé nieci-dessous),qu’ilyaundysfonctionnementouqueleProduitasubiundommagedansle  
cadred’uneutilisationnormaleduProduitconformémentàladescriptiondumoded’emploiquiaccompagneleProduit  
(ci-aprèsdénommé«Manuel d’utilisation »).  
LapériodedecetteGarantieestlimitéeà(i)cinq(5)ansàpartirdeladated’achatduProduit;ou,limitéejusqu’à  
l’expirationde(ii)30000heuresd’utilisationduProduit(ci-aprèsdénommée«Période de Garantie»).EIZOetses  
DistributeursdéclinenttouteresponsabilitéouobligationconcernantceProduitfaceàl’Acheteurinitialouàtouteautre  
personneàl’exceptiondecellesstipuléesdanslaprésenteGarantie.  
EIZOetsesDistributeurscesserontdetenirouconserverenstocktoutepiècedeceProduitaprèsl’expirationde  
lapériodedesept(7)anssuivantl’arrêtdelaproductiondetellespièces.Pourréparerlemoniteur,EIZOetses  
distributeursutiliserontdespiècesderechangeconformesànosnormesdecontrôlequalité.  
LaGarantieestvalableuniquementdanslespaysoulesterritoiresoùsetrouventlesDistributeurs.LaGarantienelimite  
aucundesdroitsreconnusparlaloiàl’Acheteurinitial.  
NonobstanttouteautreclausedecetteGarantie,EIZOetsesDistributeursn’aurontd’obligationdanslecadredecette  
Garantiepouraucundescasénumérésci-dessous:  
(a) ToutdéfautduProduitrésultantdedommagesoccasionnéslorsdutransport,d’unemodi cation,d’unealtération,  
d’unabus,d’unemauvaiseutilisation,d’unaccident,d’uneinstallationincorrecte,d’undésastre,d’unentretienet/  
oud’uneréparationincorrectseffectuésparunepersonneautrequeEIZOousesDistributeurs;  
(b) TouteincompatibilitéduProduitrésultantd’améliorationstechniqueset/ouréglementationspossibles;  
(c) Toutedétériorationducapteur;  
(d) Toutedétériorationdesperformancesd’affichagecauséeparladétériorationdesélémentsconsommablestels  
quelepanneauLCDet/oulerétroéclairage,etc.(parexempledeschangementsdeluminosité,deschangements  
del’uniformitédelaluminosité,desmodi cationsdecouleur,deschangementsdel’uniformitédescouleurs,des  
défectuositésdepixelsycomprisdespixelsbrûlés,etc.);  
(e) ToutdéfautduProduitcauséparunappareilexterne;  
(f) Toutdéfautd’unProduitsurlequellenumérodesérieoriginalaétéaltéréousupprimé;  
(g) ToutedétériorationnormaleduProduit,particulièrementcelledesconsommables,desaccessoireset/oudes  
piècesreliéesauProduit(touches,élémentspivotants,câbles,Manueld’utilisationetc.),et  
(h) Toutedéformation,décoloration,et/ougondolagedel’extérieurduProduit,ycompriscelledelasurfacedu  
panneauLCD.  
Pourbéné cierd’unservicedanslecadredecetteGarantie,l’AcheteurinitialdoitrenvoyerleProduitportpayé,dans  
sonemballaged’origineoutoutautreemballageappropriéoffrantundegrédeprotectionéquivalent,auDistributeurlocal,  
etassumeralaresponsabilitédesdommageset/oupertepossibleslorsdutransport.L’Acheteurinitialdoitprésenterune  
preuved’achatduProduitcomprenantsadated’achatpourbéné cierdeceservicedanslecadredelaGarantie.  
LaPériodedegarantiepourtoutProduitremplacéet/ouréparédanslecadredecetteGarantieexpireraàla ndela  
Périodedegarantieinitiale.  
EIZOOUSESDISTRIBUTEURSNESAURAIENTÊTRETENUSRESPONSABLESDESDOMMAGESOUPERTESDE  
DONNÉESOUD’AUTRESINFORMATIONSSTOCKÉESDANSUNMÉDIAQUELCONQUEOUUNEAUTREPARTIE  
DUPRODUITRENVOYÉÀEIZOOUAUXDISTRIBUTEURSPOURRÉPARATION.  
AUCUNEAUTREGARANTIE,EXPLICITEOUTACITE,N’ESTOFFERTEPAREIZOETSESDISTRIBUTEURS  
CONCERNANTLEPRODUITETSESQUALITÉS,PERFORMANCES,QUALITÉMARCHANDEOUADAPTATION  
ÀUNUSAGEPARTICULIER.ENAUCUNCAS,EIZOOUSESDISTRIBUTEURSNESERONTRESPONSABLES  
DESDOMMAGESFORTUITS,INDIRECTS,SPÉCIAUX,INDUITS,OUDETOUTAUTREDOMMAGEQUEL  
QU’ILSOIT(YCOMPRIS,SANSLIMITATION,LESDOMMAGESRÉSULTANTD’UNEPERTEDEPROFIT,D’UNE  
INTERRUPTIOND’ACTIVITÉS,D’UNEPERTEDEDONNÉESCOMMERCIALES,OUDETOUTAUTREMANQUE  
ÀGAGNER)RÉSULTANTDEL’UTILISATIONOUDEL’INCAPACITÉD’UTILISERLEPRODUITOUAYANTUN  
RAPPORTQUELCONQUEAVECLEPRODUIT,QUECESOITSURLABASED’UNCONTRAT,D’UNTORT,D’UNE  
NÉGLIGENCE,D’UNERESPONSABILITÉSTRICTEOUAUTRE,MÊMESIEIZOOUSESDISTRIBUTEURSONTÉTÉ  
AVERTISDELAPOSSIBILITÉDETELSDOMMAGES.CETTELIMITATIONINCLUTAUSSITOUTERESPONSABILITÉ  
QUIPOURRAITÊTRESOULEVÉELORSDESRÉCLAMATIONSD’UNTIERSCONTREL’ACHETEURINITIAL.  
L’ESSENCEDECETTECLAUSEESTDELIMITERLARESPONSABILITÉPOTENTIELLEDEEIZOETDESES  
DISTRIBUTEURSRÉSULTANTDECETTEGARANTIELIMITÉEET/OUDESVENTES.  
Appendix  
73  
GARANTÍA LIMITADA  
EIZOCorporation(enlosucesivo“EIZO”)ysusdistribuidoresautorizados(enlosucesivolos“Distribuidores”),  
conarregloydeconformidadconlostérminosdeestagarantíalimitada(enlosucesivola“Garantía”),garantizanal  
compradororiginal(enlosucesivoel“Comprador original”)quecompróelproductoespeci cadoenestedocumento(en  
losucesivoel“Producto”)aEIZOoasusDistribuidores,queEIZOysusDistribuidores,asupropiocriterio,repararán  
osustituiránelProductodeformagratuitasielCompradororiginaldetectadentrodelperiododelaGarantía(indicado  
posteriormente)queelProductonofuncionacorrectamenteoquesehaaveriadoduranteelusonormaldelmismode  
acuerdoconlasindicacionesdelmanualdeinstruccionessuministradoconelProducto(enlosucesivoel“Manual del  
usuario”).  
ElperíododevalidezdeestaGarantíaestálimitadoa(i)cinco(5)añosapartirdelafechadecompradelProductoo(ii)  
a30.000horasdeusodelProducto(enadelantedesignadocomoel“Periodo de Garantía”).EIZOysusDistribuidores  
notendránningunaresponsabilidadniobligaciónconrespectoalProductoparaconelCompradororiginalniparacon  
tercerosquenoseanlasestipuladasenlapresenteGarantía.  
EIZOysusDistribuidoresnoestaránobligadosasuministrarcualquierrecambiodelProductounavezpasadossiete  
(7)añosdesdequesedejedefabricarelmismo.Paralareparacióndelmonitor,EIZOylosdistribuidoresutilizarán  
repuestosquecumplanconnuestrosestándaresdecontroldecalidad.  
LaGarantíaesválidasóloenlospaísesyterritoriosdondeestánubicadoslosDistribuidores.LaGarantíanorestringe  
ningúnderecholegaldelCompradororiginal.  
ApesardelasestipulacionesdeestaGarantía,EIZOysusDistribuidoresnotendránobligaciónalgunabajoesta  
Garantíaenningunodeloscasosexpuestosacontinuación:  
(a) CualquierdefectodelProductocausadopordañoseneltransporte,modi cación,alteración,abuso,usoincorrecto,  
accidente,instalaciónincorrecta,desastre,mantenimientoincorrectoy/oreparaciónindebidarealizadaporun  
terceroquenoseaEIZOosusDistribuidores.  
(b) CualquierincompatibilidaddelProductodebidaaposiblesinnovacionestécnicasy/oreglamentaciones.  
(c) Cualquierdeteriorodelsensor.  
(d) Cualquierdeterioroenelrendimientodelavisualizacióncausadoporfallosenlaspiezasconsumiblescomoel  
panelLCDy/ola"Backlight",etc.(p.ej.cambiosdebrillo,cambiosdeuniformidaddelbrillo,cambiosdecolor,  
cambiosdeuniformidaddelcolor,defectosdepíxeles,incluyendopíxelesmuertos,etc.).  
(e) CualquierdefectodelProductocausadoporunequipoexterno.  
(f) CualquierdefectodelProductoenelquehayasidoalteradooborradoelnúmerodeserieoriginal.  
(g) CualquierdeterioronormaldelProducto,yenparticulardelaspiezasconsumibles,accesoriosydemás(p.ej.  
botones,piezasgiratorias,cables,Manualdelusuario,etc.).  
(h) Cualquierdeformación,decoloracióny/oalabeodelexteriordelProductoincluidalasuper ciedelpanelLCD.  
ParaobtenerservicioenlostérminosdeestaGarantía,elProductodeberáserenviadoporelCompradororiginal,  
asuDistribuidorlocal,coneltransportepreviamentepagado,enelembalajeoriginaluotroembalajeadecuadoque  
ofrezcaelmismogradodeprotección,asumiendoelriesgodedañosy/opérdidadelProductoduranteeltransporte.El  
CompradororiginaldeberápresentaruncomprobantedecompradelProductoenelquesere ejelafechadecompra  
delmismocuandolosoliciteelserviciodeGarantía.  
ElPeriododegarantíaparacualquierProductoreemplazadoy/oreparadoenlostérminosdeestaGarantíaexpiraráal  
vencerelPeriododegarantíaoriginal.  
EIZOOLOSDISTRIBUIDORESAUTORIZADOSDEEIZONOSERESPONSABILIZANDENINGÚNDAÑOO  
PÉRDIDAQUEPUEDANSUFRIRLOSDATOSUOTRAINFORMACIÓNALMACENADAENCUALQUIERMEDIOO  
CUALQUIERPARTEDECUALQUIERPRODUCTODEVUELTOAEIZOOALOSDISTRIBUIDORESDEEIZOPARA  
SUREPARACIÓN.  
EIZOYLOSDISTRIBUIDORESAUTORIZADOSDEEIZONOOFRECENNINGUNAOTRAGARANTÍA,IMPLÍCITA  
NIEXPLÍCITA,CONRESPECTOALPRODUCTOYASUCALIDAD,RENDIMIENTO,COMERCIABILIDADE  
IDONEIDADPARACUALQUIERUSOENPARTICULAR.ENNINGÚNCASOSERÁNEIZOOLOSDISTRIBUIDORES  
AUTORIZADOSDEEIZORESPONSABLESDENINGÚNDAÑOEMERGENTE,INDIRECTO,ESPECIAL,INHERENTE  
OCUALQUIERAQUESEA(INCLUYENDO,SINLIMITACIÓN,DAÑOSPORLUCROCESANTE,INTERRUPCIÓN  
DELAACTIVIDADCOMERCIAL,PÉRDIDADEINFORMACIÓNCOMERCIALOCUALQUIEROTRAPÉRDIDA  
PECUNIARIA)QUESEDERIVEDELUSOOIMPOSIBILIDADDEUSODELPRODUCTOOENRELACIÓNCONEL  
PRODUCTO,YASEABASADOENCONTRATO,PORAGRAVIO,NEGLIGENCIA,ESTRICTARESPONSABILIDAD  
OCUALQUIERAQUESEA,AUNCUANDOSEHAYAADVERTIDOAEIZOOALOSDISTRIBUIDORESDEEIZO  
DELAPOSIBILIDADDETALESDAÑOS.ESTAEXCLUSIÓNTAMBIÉNABARCACUALQUIERRESPONSABILIDAD  
QUEPUEDADERIVARSEDERECLAMACIONESHECHASPORUNTERCEROCONTRAELCOMPRADOR  
ORIGINAL.LAESENCIADEESTAESTIPULACIÓNESLIMITARLARESPONSABILIDADPOTENCIALDEEIZOYLOS  
DISTRIBUIDORESQUEPUDIERADERIVARSEDEESTAGARANTÍALIMITADAY/OVENTAS.  
Appendix  
74  
GARANZIA LIMITATA  
EIZOCorporation(acuisifaràriferimentodaquiinpoicon“EIZO”)ediDistributoriautorizzatidaEIZO(acuisifarà  
riferimentodaquiinpoicon“Distributori”)garantiscono,secondoiterminidiquestagaranzialimitata(acuisifarà  
riferimentodaquiinpoicon“Garanzia”)all’acquirenteoriginale(acuisifaràriferimentodaquiinpoicon“Acquirente  
originale”)chehaacquistatoilprodottospecificatoinquestodocumento(acuisifaràriferimentodaquiinpoicon  
“Prodotto”)daEIZOodaisuoiDistributori,cheEIZOeidistributori,alorodiscrezione,riparerannoosostituirannoil  
Prodottosenzaaddebitosel’Acquirenteoriginaletrova,entroilperiododellaGaranzia(de nitosotto),cheilProdotto  
malfunzionaesièdanneggiatonelcorsodelsuonormaleutilizzoosservandoleindicazionidelmanualediistruzioni  
allegatoalProdotto(acuisifaràriferimentodaquiinpoicon“Manuale utente”).  
LapresenteGaranziaèlimitataa(i)cinque(5)anniapartiredalladatad'acquistodelProdottoo(ii)alloscaderedi  
30.000ored'utilizzodelProdotto(acuisifaràriferimentodaquiinpoicon“Periodo di Garanzia”).EIZOeisuoi  
DistributorinonsiassumonoalcunaresponsabilitàenonhannoalcunobbligoriguardoalProdottoversol'Acquirente  
originaleoterzidiversidaquellirelativiaquestaGaranzia.  
EIZOeisuoiDistributoricesserannoditenereodiconservarequalsiasiricambiodelProdottoalloscaderedisette  
(7)annidopochelaproduzioneditaliricambièstataterminata.Perlariparazionedelmonitor,EIZOeiDistributori  
utilizzerannopartidiricambioconformiainostristandarddicontrollodellaqualità.  
LaGaranziaèvalidasoltantoneipaesidovecisonoiDistributoriEIZO.LaGaranzianonlimitaalcundirittolegale  
dell’Acquirenteoriginale.  
IndipendentementedaqualsiasialtracondizionediquestaGaranzia,EIZOeisuoiDistributorinonavrannoalcunobbligo  
derivantedaquestaGaranziainognunodeicasielencatidiseguito:  
(a) QualsiasidifettodelProdottocausatodadanniditrasporto,modi che,alterazioni,abusi,usiimpropri,incidenti,  
installazioneerrata,calamità,manutenzioneerratae/oriparazioniimproprieeseguitedaterzepartichenonsiano  
EIZOoisuoiDistributori.  
(b) QualsiasiincompatibilitàdelProdottodovutaapossibiliinnovazionitecnichee/onormative.  
(c) Qualsiasideterioramentodelsensore.  
(d) Qualsiasideterioramentodelleprestazionidelloschermocausatodaldeterioramentodelleparticonsumabili,come  
ilpannelloLCDe/olaretroilluminazione,ecc.(peresempio:icambiamentidiluminosità,cambiamentidiuniformità  
dellaluminosità,icambiamentidicolore,icambiamentidiuniformitàdelcolore,idifettideipixel,inclusiipixel  
bruciati,ecc.).  
(e) QualsiasidifettodelProdottocausatodaapparecchiatureesterne.  
(f) QualsiasidifettodelProdottoincuiilnumerodiserieoriginalesiastatoalteratoorimosso.  
(g) QualsiasinormaledeterioramentodelProdotto,inparticolarmodonellesuepartidiconsumo,accessori,e/o  
attacchi(peresempio:tasti,partirotanti,cavi,Manualedell’utente,ecc.).  
(h) Qualsiasitipodideformazione,scolorimento,e/odiinvolucroesternodelProdottoinclusalasuper ciedelpannello  
LCD.  
PerricevereassistenzatecnicaconquestaGaranzia,l’AcquirenteoriginaledeveinviareilProdotto,contrasporto  
pre-pagato,nellasuaconfezioneoriginaleoaltraconfezioneadeguatachefornisceunlivelloanalogodiprotezione,  
assumendosiilrischiodidannie/operditaintransito,alDistributorelocale.L’Acquirenteoriginaledevepresentarela  
provadiacquistochestabilisceladatadiacquistodelProdottoquandorichiedeserviziosottoGaranzia.  
IlPeriododigaranziaperqualsiasiProdottosostituitoe/oriparatosottoquestaGaranziascadealla nedelPeriododi  
garanziaoriginale.  
EIZOOISUOIDISTRIBUTORINONSONORESPONSABILIPERQUALSIASIDANNOOPERDITADIDATIOALTRE  
INFORMAZIONIMEMORIZZATISUQUALSIASISUPPORTOOQUALSIASIPARTEDIQUALSIASIPRODOTTO  
INVIATOAEIZOOISUOIDISTRIBUTORIPERRIPARAZIONI.  
EIZOEISUOIDISTRIBUTORINONOFFRONOALCUNAGARANZIAADDIZIONALE,IMPLICITAOESPLICITA,  
RIGUARDOILPRODOTTOELASUAQUALITÀ,PRESTAZIONI,VENDIBILITÀOAPPROPRIATEZZAPER  
QUALSIASIUSOPARTICOLARE.INNESSUNCASOEIZOOIDISTRIBUTORIEIZOAUTORIZZATISARANNO  
RESPONSABILIPERQUALSIASIDANNOACCIDENTALE,INDIRETTO,SPECIALE,CONSEGUENTEODI  
QUALSIASIALTRANATURA(INCLUSI,SENZALIMITI,DANNIPERPERDITADIPROFITTI,INTERRUZIONEDELLE  
ATTIVITÀ,PERDITADIINFORMAZIONID’AFFARIOQUALSIASIALTRAPERDITAPECUNIARIA)DERIVANTI  
DALL’USOODALL’IMPOSSIBILITÀDIUSAREILPRODOTTOOINQUALSIASIRELAZIONEALPRODOTTO,  
SIASUBASEDICONTRATTO,TORTO,NEGLIGENZA,STRETTARESPONSABILITÀOALTRIMENTI,ANCHE  
SEEIZOOIDISTRIBUTORIEIZOAUTORIZZATISONOSTATIAVVERTITIDELLAPOSSIBILITÀDITALIDANNI.  
QUESTAESCLUSIONEINCLUDEANCHEQUALSIASIRESPONSABILITÀCHEPOSSAINSORGEREDARECLAMI  
DITERZICONTROL’ACQUIRENTEORIGINALE.L’ESSENZADIQUESTOPROVVEDIMENTOÈLIMITARELA  
RESPONSABILITÀPOTENZIALEDIEIZOEDEIDISTRIBUTORIDERIVANTEDAQUESTAGARANZIALIMITATAE/O  
DALLEVENDITE.  
Appendix  
75  
BEGRÄNSAD GARANTI  
EIZOCorporation(nedankallat“EIZO”)ochEIZOsauktoriseradedistributörer(nedankallade“Distributörer”)garanterar  
ienlighetmedvillkorenidennabegränsadegaranti(nedankallad“Garantin”)denursprungligeköparen(nedankallad  
den“Ursprunglige köparen”)somköptedenidokumentetspeci ceradeprodukten(nedankallad“Produkten”)från  
EIZOellerDistributörer,attEIZOellerDistributörerenligtegetgott nnandekostnadsfrittantingenrepareraellerbytaut  
dendefektaProduktenomdenUrsprungligeköpareninomGarantiperioden(de nierasnedan)upptäckerattProdukten  
fungerarfelaktigtellerskadasundernormalanvändningavProduktenienlighetmedbeskrivningenibruksanvisningen  
(nedankallad“Bruksanvisning”).  
Giltighetsperiodenfördennagarantiärbegränsadtill(i)fem(5)årfråndatumetförProduktensinköpeller,omdetta  
inträffartidigare,begränsattillutlöpandetav(ii)30000timmarsanvändningavProdukten(härikallad“Garantiperioden”).  
EIZOochDistributörerskainteundernågravillkorhanågotannatansvaränvadsomangesidennagarantigällande  
ProduktenirelationtilldenUrsprungligeköparenellertredjepart.  
EIZOochDistributörerkommerattupphöramedlagerhållningavProduktensdelareftersju(7)årefterattproduktionen  
avdessadelarupphört.NätskärmenreparerasanvänderEIZOochdistributörerreservdelarsomuppfyllervåra  
kvalitetsstandarder.  
GarantinärendastgiltigideländerdärdetfinnsDistributörer.GarantinbegränsarintenågraavdenUrsprunglige  
köparenslagstadgaderättigheter.  
OavsettandravillkoridennagarantiskainteEIZODistributörerundernågravillkorhanågotansvarinågotavdefall  
sombeskrivsnedan:  
(a) NärnågonbristfällighethosProduktenkanhärledastillatthauppståttvidfrakt,modifiering,ändring,felaktigt  
handhavande,olycka,felaktiginstallation,katastrof,felaktigtunderhålloch/ellerfelaktigreparationutfördavtredje  
partannanänEIZOochDistributörer.  
(b) AllaformeravinkompatibilitethosProduktenpågrundavmöjligatekniskainnovationeroch/ellerbestämmelser.  
(c) Allaförsämringaravsensorn.  
(d) Alla försämringar av bildens prestanda beroende på förbrukningsdelar så som LCD-panel och/eller  
bakgrundsbelysningetc.(t.ex.ändringariljusstyrka,jämnhetiljusstyrka,färg,färgjämnhet,defektapixlaroch/eller  
fastlysandepixlaretc.).  
(e) AlladefekterhosProduktensomorsakatsavexternutrustning.  
(f) AlladefekterhosProduktenpåvilkendetursprungligaserienumretharändratselleravlägsnats.  
(g) AllnormalförsämringavProdukten,specielltförbrukningsartiklar,tillbehöroch/elleryttredelar(t.ex.knappar,  
roterandedelar,kablar,Bruksanvisningenetc.).  
(h) Varjedeformation,missfärgningoch/ellerskevhetavProduktensyttreinklusiveytanpåLCD-panelen.  
FöratterhållaserviceunderdennagarantimåstedenUrsprungligeköparen(medhänseendetillriskenförskada  
och/ellerförlustundertransport)levereraProduktentillnärmasteDistributörmedförebetaldfrakt,idessursprungliga  
förpackningellerannanfullgodförpackningsomgerlikvärdigtskydd.DenUrsprungligeköparenmåstekunnavisa  
inköpsbevisförProduktensomklargörProduktensinköpsdatumvidbegäranavgarantiservice.  
Garantiperiodenförallautbyttaoch/ellerrepareradeprodukterunderdennagarantiskallupphöravidutgångenavden  
ursprungligaGarantiperioden.  
EIZOELLERDISTRIBUTÖRERÄRINTEANSVARIGAFÖRNÅGONFORMAVSKADAELLERFÖRLUSTAVDATA  
ELLERANNANINFORMATIONSOMHARLAGRATSINÅGONFORMAVMEDIAELLERANNANDELAVNÅGON  
PRODUKTSOMHARRETURNERATSTILLEIZOELLERDISTRIBUTÖRERFÖRREPARATION.  
EIZOOCHDISTRIBUTÖRERNAGARANTERARINGET,UTTRYCKLIGENELLERUNDERFÖRSTÅTT,VAD  
BETRÄFFARPRODUKTENOCHDESSKVALITET,PRESTANDA,SÄLJBARHETELLERLÄMPLIGHETFÖRNÅGON  
FORMAVSPECIELLANVÄNDNING.UNDERINGAOMSTÄNDIGHETERSKALLEIZOELLERDISTRIBUTÖRERNA  
HÅLLASANSVARIGAFÖRNÅGRASOMHELSTUNDERORDNADE,INDIREKTA,SPECIELLA,DÄRAVFÖLJANDE  
ELLERÖVRIGASKADOR(INKLUSIVE,UTANBEGRÄNSNINGTILL,SKADORFÖRFÖRLUSTAVINKOMST,  
AVBRUTENAFFÄRSRÖRELSE,FÖRLUSTAVAFFÄRSINFORMATIONELLERANNANSÄRSKILDFÖRLUST)SOM  
UPPSTÅTTSOMETTRESULTATAVANVÄNDNINGELLEROFÖRMÅGAATTANVÄNDAPRODUKTENELLERI  
NÅGONFORMAVANSLUTNINGTILLPRODUKTERNA,VARESIGDETTAGRUNDASPÅKONTRAKT,ÅTALBAR  
HANDLING,FÖRSUMLIGHET,ANSVARSSKYLDIGHETELLERANNAT,ÄVENOMEIZOELLERDISTRIBUTÖRERNA  
HARINFORMERATSBETRÄFFANDEMÖJLIGHETATTSÅDANASKADORFÖRELIGGER.DETTAUNDANTAG  
OMFATTARÄVENALLFORMAVANSVARSSKYLDIGHETSOMKANUPPSTÅGENOMENTREDJEPARTSANSPRÅK  
GENTEMOTDENURSPRUNGLIGEKÖPAREN.GRUNDBESTÅNDSDELENIBESTÄMMELSENÄRATTBEGRÄNSA  
DETEVENTUELLAANSVARSTAGANDETFÖREIZOOCHDISTRIBUTÖRERNASOMKANUPPSTÅGENOMDENNA  
BEGRÄNSADEGARANTIOCH/ELLERFÖRSÄLJNING.  
Appendix  
76  
ΠΕΡΙΟΡΙΣΜΕΝΗ ΕΓΓΥΗΣΗ  
Η EIZO Corporation (στο εξής «EIZO») και οι διανομείς που εξουσιοδοτεί η EIZO (στο εξής «Διανομείς»)  
παρέχουνεγγύηση,υποκείμενηκαισύμφωναμετουςόρουςτηςπαρούσαςπεριορισμένηςεγγύησης(στοεξής  
«Εγγύηση»),στοναρχικόαγοραστή(στοεξής«Αρχικός Αγοραστής»)οοποίοςαγόρασετοπροϊόνπουκαθορίζεταιστο  
παρόνέγγραφο(στοεξής«Προϊόν»)απότηνEIZOήτουςΔιανομείς,ηοποίαεξασφαλίζειότιηEIZOκαιοιΔιανομείς,  
σύμφωναμετηδιακριτήευχέρειάτους,είτεθαεπισκευάσουνείτεθααντικαταστήσουντοΠροϊόνχωρίςχρέωσηεάνο  
ΑρχικόςΑγοραστήςαντιληφθείεντόςτηςΠεριόδουΕγγύησης(ορίζεταικατωτέρω)ότιτοΠροϊόνδυσλειτουργείήέχει  
υποστείβλάβηκατάτηδιάρκειακανονικήςχρήσηςτουΠροϊόντοςσύμφωναμετηνπεριγραφήστοεγχειρίδιοχρήσηςπου  
συνοδεύειτοΠροϊόν(στοεξής«Εγχειρίδιο Χρήστη»).  
ΗπερίοδοςτηςπαρούσαςΕγγύησηςείναι(i)πέντε(5)έτηαπότηνημερομηνίααγοράςτουΠροϊόντος,ή,στηλήξητων  
(ii)30.000ωρώνχρήσηςτουΠροϊόντος(στοεξής«Περίοδος Εγγύησης»).ΗEIZOκαιοιΔιανομείςδενφέρουνκαμία  
ευθύνηήυποχρέωσηόσοναφοράτοΠροϊόνσεσχέσημετονΑρχικόΑγοραστήήοποιοδήποτετρίτομέρος,ούτεάλλη  
ευθύνηδιαφορετικήαπόαυτήνπουπαρέχεταιστηνπαρούσαΕγγύηση.  
ΗEIZOκαιοιΔιανομείςθαπαύσουνναδιατηρούνήνααποθηκεύουντυχόνεξαρτήματατουΠροϊόντοςκατόπιντηςλήξης  
τωνεπτά(7)ετώνμετάτηδιακοπήτηςπαραγωγήςτέτοιωνεξαρτημάτων.Κατάτηνεπισκευήτηςοθόνης,ηEIZOκαιοι  
ΔιανομείςθαχρησιμοποιήσουνανταλλακτικάεπισκευήςπουσυμμορφώνονταιμεταπρότυπάμαςγιατηΔιασφάλιση  
Ποιότητας.  
ΗΕγγύησηισχύειμόνοσεχώρεςήπεριοχέςόπουβρίσκονταιοιΔιανομείς.ΗΕγγύησηδενπεριορίζειοποιαδήποτε  
νόμιμαδικαιώματατουΑρχικούΑγοραστή.  
ΛαμβανομένηςυπόψηκάθεδιάταξηςτηςπαρούσαςΕγγύησης,ηEIZOκαιοιΔιανομείςδενθαέχουνκαμίααπολύτως  
υποχρέωσησύμφωναμετηνπαρούσαΕγγύησησεοποιαδήποτεαπότιςπεριπτώσειςπουδιατυπώνονταικατωτέρω:  
(α) ΤυχόνελάττωματουΠροϊόντοςπουπροκαλείταιαπόζημιάκατάτημεταφορά,τροποποίηση,αλλαγή,κατάχρηση,  
λανθασμένηχρήση,ατύχημα,λανθασμένηεγκατάσταση,καταστροφή,εσφαλμένησυντήρησηή/καιλανθασμένη  
επισκευήαπότρίτομέροςεκτόςτηςEIZOκαιτωνΔιανομέων,  
(β) ΤυχόνασυμβατότητατουΠροϊόντοςλόγωπιθανώντεχνικώνκαινοτομιώνή/καικανονισμών,  
(γ) Τυχόνεπιδείνωσητουαισθητήρα,  
(δ) Τυχόνεπιδείνωσητηςαπόδοσηςοθόνηςπουπροκαλείταιαπότηφθοράαναλώσιμωνεξαρτημάτωνόπως  
τηςοθόνηςLCDή/καιτουφωτόςυποβάθρου,κτλ.(π.χ.αλλαγέςστηφωτεινότητα,αλλαγέςστηνομοιομορφία  
φωτεινότητας,αλλαγέςστοχρώμα,αλλαγέςστηνομοιομορφίαχρώματος,ελαττώματασεpixelπεριλαμβανομένων  
τωνκαμένωνpixel,κτλ.),  
(ε) ΤυχόνελάττωματουΠροϊόντοςπουπροκαλείταιαπόεξωτερικόεξοπλισμό,  
(στ)ΤυχόνελάττωματουΠροϊόντοςστοοποίοέχειτροποποιηθείήαφαιρεθείογνήσιοςαριθμόςσειράς,  
(ζ) Τυχόν φυσιολογική φθορά του προϊόντος, ιδιαίτερα αυτής των αναλώσιµων, των αξεσουάρ ή/και των  
προσαρτηµάτων(π.χ.κουµπιά,περιστρεφόµεναµέρη,καλώδια,ΕγχειρίδιοΧρήστη,κτλ.),και  
(η) Τυχόν παραμόρφωση, αποχρωματισμό ή/και διαστρέβλωση του εξωτερικού μέρους του προϊόντος,  
περιλαμβανομένηςτηςεπιφάνειαςτηςοθόνηςLCD.  
ΟΑρχικόςΑγοραστήςγιαναδικαιούταιυπηρεσίεςεπισκευήςσύμφωναμετηνΕγγύηση,θαπρέπειναπαραδώσειτο  
Προϊόν,μεπληρωμέναταμεταφορικάέξοδα,στηναρχικήτουσυσκευασίαήσεάλληεπαρκήσυσκευασίαμεισότιμο  
βαθμόπροστασίας,αναλαμβάνονταςτονκίνδυνοβλάβηςή/καιαπώλειαςκατάτημεταφορά,στοντοπικόΔιανομέα.Ο  
ΑρχικόςΑγοραστήςότανζητάυπηρεσίεςεπισκευήςσύμφωναμετηνΕγγύηση,θαπρέπειναπροσκομίζειτηναπόδειξη  
αγοράςτουΠροϊόντοςκαιτηνημερομηνίατηςαγοράς.  
ΗΠερίοδοςΕγγύησηςγιαοποιοδήποτεαντικατεστημένοή/καιεπισκευασμένοπροϊόνσύμφωναμετηνπαρούσα  
ΕγγύησηλήγειστοτέλοςτηςαρχικήςΠεριόδουΕγγύησης.  
ΗEIZOΉΟΙΔΙΑΝΟΜΕΙΣΔΕΝΕΥΘΥΝΟΝΤΑΙΓΙΑΟΠΟΙΑΔΗΠΟΤΕΒΛΑΒΗΉΑΠΩΛΕΙΑΔΕΔΟΜΕΝΩΝΉΑΛΛΩΝ  
ΠΛΗΡΟΦΟΡΙΩΝΠΟΥΑΠΟΘΗΚΕΥΟΝΤΑΙΣΕΟΠΟΙΟΔΗΠΟΤΕΜΕΣΟΉΟΠΟΙΟΔΗΠΟΤΕΑΛΛΟΜΕΡΟΣΣΕ  
ΟΠΟΙΟΔΗΠΟΤΕΠΡΟΪΟΝΠΟΥΕΠΙΣΤΡΕΦΕΤΑΙΣΤΗΝEIZOΉΣΕΔΙΑΝΟΜΕΑΓΙΑΕΠΙΣΚΕΥΗ.  
ΗEIZOΚΑΙΟΙΔΙΑΝΟΜΕΙΣΔΕΝΠΑΡΕΧΟΥΝΚΑΜΙΑΠΕΡΑΙΤΕΡΩΕΓΓΥΗΣΗ,ΡΗΤΗΉΣΥΝΕΠΑΓΟΜΕΝΗ,ΟΣΟΝ  
ΑΦΟΡΑΤΟΠΡΟΪΟΝΚΑΙΤΗΝΠΟΙΟΤΗΤΑ,ΤΗΝΑΠΟΔΟΣΗ,ΤΗΝΕΜΠΟΡΕΥΣΙΜΟΤΗΤΑΉΤΗΝΚΑΤΑΛΛΗΛΟΤΗΤΑ  
ΤΟΥΓΙΑΟΠΟΙΑΔΗΠΟΤΕΣΥΓΚΕΚΡΙΜΕΝΗΧΡΗΣΗ.ΣΕΚΑΜΙΑΠΕΡΙΠΤΩΣΗΗEIZOΉΟΙΔΙΑΝΟΜΕΙΣΔΕΝ  
ΘΑΕΥΘΥΝΟΝΤΑΙΓΙΑΚΑΜΙΑΑΠΟΛΥΤΩΣΤΥΧΑΙΑ,ΕΜΜΕΣΗ,ΕΙΔΙΚΗ,ΣΥΝΕΠΑΓΟΜΕΝΗΉΑΛΛΗΒΛΑΒΗ  
(ΠΕΡΙΛΑΜΒΑΝΟΜΕΝΩΝ,ΜΕΤΑΞΥΑΛΛΩΝ,ΒΛΑΒΩΝΉΑΠΩΛΕΙΑΣΚΕΡΔΩΝ,ΔΙΑΚΟΠΗΣΕΠΙΧΕΙΡΗΜΑΤΙΚΩΝ  
ΔΡΑΣΤΗΡΙΟΤΗΤΩΝ,ΑΠΩΛΕΙΑΣΕΠΙΧΕΙΡΗΜΑΤΙΚΩΝΠΛΗΡΟΦΟΡΙΩΝΉΤΥΧΟΝΑΛΛΗΣΧΡΗΜΑΤΙΚΗΣΑΠΩΛΕΙΑΣ)  
ΠΟΥΠΡΟΚΥΠΤΕΙΑΠΟΤΗΧΡΗΣΗΉΤΗΝΑΝΙΚΑΝΟΤΗΤΑΧΡΗΣΗΣΤΟΥΠΡΟΪΟΝΤΟΣΉΤΥΧΟΝΑΛΛΗΣΣΥΝΔΕΣΗΣ  
ΜΕΤΟΠΡΟΪΟΝ,ΕΙΤΕΒΑΣΙΖΕΤΑΙΣΕΣΥΜΒΟΛΑΙΟ,ΒΛΑΒΗ,ΑΜΕΛΕΙΑ,ΑΥΣΤΗΡΗΕΥΘΥΝΗΉΕΙΔΑΛΛΩΣ,ΑΚΟΜΗ  
ΚΙΕΑΝΗEIZOΉΟΙΔΙΑΝΟΜΕΙΣΕΝΗΜΕΡΩΘΟΥΝΓΙΑΤΗΝΠΙΘΑΝΟΤΗΤΑΤΕΤΟΙΩΝΖΗΜΙΩΝ.ΗΕΞΑΙΡΕΣΗΑΥΤΗ  
ΠΕΡΙΛΑΜΒΑΝΕΙΕΠΙΣΗΣΟΠΟΙΑΔΗΠΟΤΕΕΥΘΥΝΗΕΝΔΕΧΕΤΑΙΝΑΠΡΟΚΥΨΕΙΑΠΟΑΞΙΩΣΕΙΣΤΡΙΤΟΥΜΕΡΟΥΣ  
ΚΑΤΑΤΟΥΑΡΧΙΚΟΥΑΓΟΡΑΣΤΗ.ΗΟΥΣΙΑΤΟΥΟΡΟΥΑΥΤΟΥΕΙΝΑΙΝΑΠΕΡΙΟΡΙΣΕΙΤΗΝΠΙΘΑΝΗΕΥΘΥΝΗΤΗΣ  
EIZOΚΑΙΤΩΝΔΙΑΝΟΜΕΩΝΠΟΥΠΡΟΚΥΠΤΕΙΑΠΟΤΗΝΠΑΡΟΥΣΑΕΓΓΥΗΣΗΉ/ΚΑΙΤΙΣΠΩΛΗΣΕΙΣ.  
Appendix  
77  
ОГРАНИЧЕННАЯ ГАРАНТИЯ  
EIZOCorporation(называемаявдальнейшем“EIZO”)иавторизированныеEIZOдистрибуторы(называемыев  
дальнейшем“Дистрибуторы”)гарантируют,всоответствиисусловиямиипунктамиэтойограниченнойгарантии  
(называемойвдальнейшем“Гарантия”),первичномупокупателю(называемомувдальнейшем“Первоначальный  
покупатель”),которыйприобрелуEIZOилиДистрибуторовпродукт,указанныйвэтомдокументе(называемый  
вдальнейшем“Продукт”),чтоEIZOилиДистрибуторынасвоеусмотрениелибобесплатноотремонтируют,  
либобесплатнозаменятПродукт,еслиПервоначальныйпокупательпризнаетвпределахГарантийногосрока  
(определенногониже),чтоПродуктнеисправенилионповрежденпроцессенормальногоиспользованияпродукта  
всоответствиисописаниемвинструкциипоэксплуатации,прилагаемойкПродукту(называемойвдальнейшем  
“Руководство пользователя”).  
Гарантийныйпериодограниченсроком(i)пять(5)летотдатыприобретенияПродуктаилиограниченсроком  
(ii)30000часовиспользованияПродукта(называемыйвдальнейшем“Гарантийный период”).EIZOи  
ДистрибуторыненесутникакойответственностиинеберутобязательствотносительноПродуктапоотношениюк  
Первоначальномупокупателюилипоотношениюклюбымтретьимсторонам,кромеобязательств,оговоренныхв  
этойГарантии.  
EIZOиДистрибуторыпрекратятхранениеилискладированиелюбыхдеталейПродуктапоистечениисеми(7)  
летпослепрекращенияпроизводстватакихдеталей.ВслучаеремонтамонитораEIZOиДистрибьюторыбудут  
использоватьзапчасти,которыесоответствуютнашимстандартамQC(контролькачества).  
Гарантиядействительнатольковстранахилирегионах,гдерасположеныДистрибуторы.Гарантияне  
ограничиваетникакиезаконныеправаПервоначальногопокупателя.  
НесмотрянадругиеусловияэтойГарантииEIZOиДистрибуторыненесутникакихобязательствсогласноэтой  
Гарантиивлюбомизперечисленныхнижеслучаев:  
(а) ЛюбыедефектыПродукта,вызванныеповреждениямиприперевозке,модификацией,изменением,  
неправильнымобращением,неправильнымиспользованием,авариями,неправильнойустановкой,  
стихийнымибедствиями,неправильнымуходоми/илинеправильнымремонтомтретьейстороной,отличной  
отEIZOилиДистрибуторов;  
(б) ЛюбыенесовместимостиПродуктаиз-затехническихусовершенствованийи/илиизменениятехнических  
норм;  
(в) Любоеповреждениедатчика;  
(г) Любыеухудшенияработыдисплея,вызванныеизнашиваниемневосстановимыхчастей,такихкак  
панельЖКДи/илиподсветкаит.д.(например,изменениевяркости,изменениевравномерностияркости,  
изменениевцветности,изменениевравномерностицветности,изменениевпикселах,включаявыгоревшие  
пикселыит.д.);  
(д) ЛюбыедефектыПродукта,вызванныевнешнимоборудованием;  
(е) ЛюбыедефектыПродукта,прикоторыхоригинальныйсерийныйномербылизмененилиудален;  
(ж) Любые естественные ухудшения продукта, в частности, вызванные износом расходных частей,  
принадлежностейи/илиприспособлений(например,кнопок,вращающихсячастей,кабелей,Руководства  
пользователяит.д.);и  
(з) Любыедеформации,измененияцветаи/иликороблениявнешнейповерхностипродукта,включая  
поверхностьпанелиЖКД.  
ЧтобыполучитьтехническоеобслуживаниеврамкахГарантии,Первоначальныйпокупательдолжендоставить  
ПродуктместномуДистрибутору,оплативперевозку,вегооригинальнойупаковкеиливдругойсоответствующей  
упаковке,обеспечивающейравноценнуюстепеньзащиты,принимаявовниманиерискповрежденияи/илиутерюпри  
транспортировке.ПризапросетехническогообслуживанияврамкахГарантииПервоначальныйпокупательдолжен  
предоставитьсвидетельствопокупкипродуктаидатыпокупки.  
Гарантийныйпериоддлялюбогозамененногои/илиотремонтированногопродуктаврамкахГарантииистекаетвконце  
завершениясрокадействияоригинальногоГарантийногопериода.  
EIZOИЛИДИСТРИБУТОРЫНЕНЕСУТОТВЕТСТВЕННОСТИЗАЛЮБЫЕПОВРЕЖДЕНИЯИЛИУТЕРЮДАННЫХИЛИ  
ДРУГОЙИНФОРМАЦИИ,ХРАНЯЩИХСЯНАКАКИХ-ЛИБОНОСИТЕЛЯХИНФОРМАЦИИИЛИНАЛЮБЫХДРУГИХ  
ЧАСТЯХПРОДУКТА,КОТОРЫЙВОЗВРАЩЕНEIZOИЛИДИСТРИБУТОРАМДЛЯРЕМОНТА.  
EIZOИДИСТРИБУТОРЫНЕДАЮТНИКАКОЙДАЛЬНЕЙШЕЙГАРАНТИИ,ВЫРАЖЕННОЙИЛИПОДРАЗУМЕВАЕМОЙ,  
ОТНОСИТЕЛЬНО ПРОДУКТА И ЕГО КАЧЕСТВА, ТЕХНИЧЕСКИХ ХАРАКТЕРИСТИК, ТОВАРНОСТИ ИЛИ  
СООТВЕТСТВИЯДЛЯКАКОГО-ЛИБООПРЕДЕЛЕННОГОИСПОЛЬЗОВАНИЯ.НИПРИКАКИХУСЛОВИЯХEIZO  
ИЛИДИСТРИБУТОРЫНЕНЕСУТОТВЕТСТВЕННОСТИЗАЛЮБОЙСЛУЧАЙНЫЙ,КОСВЕННЫЙ,СПЕЦИАЛЬНЫЙ,  
ПОБОЧНЫЙИЛИИНОЙУЩЕРБ(ВКЛЮЧАЯ,БЕЗОГРАНИЧЕНИЙ,УЩЕРБИЗ-ЗАНЕПОЛУЧЕННОЙПРИБЫЛИ,  
ПРЕРЫВАНИЯ БИЗНЕСА, ПОТЕРИ КОММЕРЧЕСКОЙ ИНФОРМАЦИИ ИЛИ ЛЮБЫЕ ДРУГИЕ ФИНАНСОВЫЕ  
ПОТЕРИ),ВОЗНИКШИЙИЗ-ЗАИСПОЛЬЗОВАНИЯИЛИНЕВОЗМОЖНОСТИИСПОЛЬЗОВАТЬПРОДУКТИЛИВ  
ЛЮБОЙДРУГОЙСВЯЗИСПРОДУКТОМ,ЛИБООСНОВАННЫЙНАКОНТРАКТНЫХОТНОШЕНИЯХ,ГРАЖДАНСКИХ  
ПРАВОНАРУШЕНИЯХ,НЕБРЕЖНОСТИ,ПРИЧИНЕНИЯУЩЕРБАТРЕТЬЕЙСТОРОНЕИЛИЧЕМ-ЛИБОЕЩЕ,ДАЖЕ  
ЕСЛИEIZOИЛИДИСТРИБУТОРЫБЫЛИУВЕДОМЛЕНЫОВОЗМОЖНОСТИТАКОГОУЩЕРБА.ЭТОИСКЛЮЧЕНИЕ  
ТАКЖЕВКЛЮЧАЕТЛЮБЫЕОБЯЗАТЕЛЬСТВА,КОТОРЫЕМОГУТВОЗНИКНУТЬВРЕЗУЛЬТАТЕТРЕБОВАНИЙ  
ТРЕТЬЕЙСТОРОНЫВОТНОШЕНИИПЕРВОНАЧАЛЬНОГОПОКУПАТЕЛЯ.СУЩЕСТВОМЭТОГОПОЛОЖЕНИЯ  
ЯВЛЯЕТСЯОГРАНИЧЕНИЕПОТЕНЦИАЛЬНОЙОТВЕТСТВЕННОСТИEIZOИДИСТРИБУТОРОВ,ВОЗНИКАЮЩЕЙИЗ-  
ЗАЭТОЙОГРАНИЧЕННОЙГАРАНТИИИ/ИЛИПРОДАЖ.  
Appendix  
78  
有限责任保证书  
EIZOCorporation 以下简称 EIZO 和EIZO 授权的经销商 以下简称 经销商  
”）  
接受并依照本有限责任保证书 以  
（
（
“
（
“
”），  
“
下简称 保证书 之条款 向从EIZO 和经销商购买本文中所规定产品 以下简称 产品 的原买方 以下称 原买方  
”） ”） ”）  
“
，
（
（
“
提供保证 在保证期内 规定如下 如果原买方发现按本产品所附使用说明书 以下简称 用户手册 所述方式正常使  
）， ”）  
：
（
（
“
用本产品过程中 本产品出现故障或损坏 EIZO 和经销商根据其独自的判断免费修理或更换该产品  
。
，
，
本保证期限定为 i 自本产品购买之日起的五 5 年期间或限定为到达 ii 使用本产品3 万小时的期限 以下简称 保证期限  
（ ） （ ） （ ） ”）。  
（
“
EIZO和经销商将不向原买方或任何第三方承担本保证书所规定之外的与本产品有关的任何责任或义务  
。
本产品的任何部件停产七(7) 年后 EIZO 和经销商将不再保留或保管任何这类部件 维修显示器时 EIZO 与经销商将使  
，
用符合我方质量控制标准的替换零件  
。
，
。
本保证书仅对于设有经销商的国家或地区有效 本保证书并不限定原买方的任何法律权利  
。
。
无论本保证书的任何其他条款如何规定 对于任何下列情况之一 EIZO 和经销商将不承担本保证书规定责任  
，
，
：
(a) 由于运输损害 改装 改动 滥用 误用 意外事故 错误安装 灾害 维护不善和/ 或由除EIZO 和经销商以外的  
、
、
、
、
、
第三方进行不适当的修理造成本产品的任何故障  
、
、
、
。
(b) 由于可能发生的技术变更和/ 或调整造成本产品的任何不兼容性  
。
(c) 传感器的任何劣化  
。
(d) 由于诸如液晶显示屏 LCD 和/ 或背灯等消耗品部件的老化造成的任何显示性能低劣 如亮度变化 亮度均一性变化  
（
色彩变化 色彩均一性变化 如烧伤像素等像素缺陷  
）
（
、
、
、
、
）。  
(e) 因外部设备造成本产品的任何故障  
。
(f) 因本产品的原序号被改变或消除造成本产品的任何故障  
。
(g) 本产品的任何正常老化 尤其是消耗品 附件和/ 或附加装置 如按钮 旋转部件 电缆 用户手册等 以及  
）、  
，
、
（
、
、
、
(h) 本产品表面包括液晶显示屏 LCD 表面的任何变形 变色和/ 翘曲  
。
（
）
、
为了获得本保证书规定的服务 原买方必须使用原包装或其他具有同等保护程度的适当包装将本产品运送到当地的经销商  
，
，
并且预付运费 承担运输中的损坏和/ 或损失的风险 要求提供本保证书规定的服务时 原买方必须提交购买本产品和标  
，
明此购买日期的证明  
。
，
。
按本保证书规定进行了更换和/ 或修理的任何产品的保证期限 将在原保证期限结束时终止  
，
。
在返回给EIZO 和经销商进行修理后 任何产品的任何媒体或任何部件中储存的数据或其他信息发生任何损坏或损失 对  
，
，
此EIZO 和经销商将不承担责任  
。
对于本产品及其质量 性能 可销售性以及对于特殊用途的适合性 EIZO 和经销商不提供其他任何明示或暗示的保证 因  
、
、
，
。
使用本产品或无法使用本产品或因与本产品有任何关系 无论是否根据合同 而造成: 任何附带的 间接的 特殊的 随  
（
）
、
、
、
之发生的或其他的损害 包括但不仅限于 利润损失 业务中断 业务信息丢失或其他任何金钱损失 以及侵权行为 过失  
（
：
、
、
）
、
、
。
严格赔偿责任或其他责任 即使已经向EIZO 和经销商提出了发生这些损害的可能性 对此EIZO 和经销商概不承担责任  
，
，
本免责条款还包括因第三方向原买方提出索赔而可能发生的任何责任 本条款的本质是限定由于本有限责任保证书和/ 或  
销售本产品所发生的EIZO 和经销商的潜在责任  
。
。
Appendix  
79  
Recycling Information  
Recycling Information  
Thisproduct,whendisposedof,issupposedtobecollectedandrecycledaccordingtoyourcountry’s  
legislationtoreduceenvironmentalburden.Whenyoudisposeofthisproduct,pleasecontactadistributoror  
anaf liateinyourcountry.  
ThecontactaddresseesarelistedontheEIZOwebsitebelow.  
http://www.eizo.com  
ForrecyclinginformationforcustomersinSwitzerland,pleaserefertothefollowingwebsite.  
http://www.swico.ch  
Informationen zum Thema Recycling  
DiesesProduktmussgemäßdenVorschriftenIhresLandeszurEntlastungderUmweltrecycletwerden.  
WendenSiesichbeiderEntsorgungdiesesProduktsaneinenVerteilerodereineTochtergesellschaftin  
IhremLand.  
DieAdressenzurKontaktaufnahmesindaufderuntenangegebenenWebsitevonEIZOaufgeführt.  
http://www.eizo.com  
KundeninderSchweizentnehmenInformationenzumRecyclingderfolgendenWebsite:  
http://www.swico.ch  
Informations sur le recyclage  
Ceproduitdoitêtrejetéauxpointsdecollecteprévusàceteffetetrecycléconformémentàlalégislationde  
votrepays,a nderéduirel’impactsurl’environnement.Lorsquevousjetezceproduit,veuillezcontacterun  
distributeurouunesociétéaf liéedevotrepays.  
LesadressesdesdistributeurssontrépertoriéessurlesiteWebEIZOci-dessous.  
http://www.eizo.com  
PourlesclientsenSuisse,veuillezconsulterlesiteWebsuivantafind’obtenirdesinformationssurle  
recyclage.  
http://www.swico.ch  
Información sobre reciclaje  
Esteproductodebedesecharseyreciclarsesegúnlalegislacióndelpaísparareducirelimpacto  
medioambiental.Cuandodeseedeshacersedeesteproducto,póngaseencontactoconundistribuidoro  
una lialdesupaís.  
EncontrarálasdireccionesdecontactoenelsitiowebdeEIZOqueseindicaacontinuación.  
http://www.eizo.com  
Informazioni sul riciclaggio  
Perlosmaltimentoeilriciclaggiodelpresenteprodotto,attenersiallenormativevigentinelpropriopaeseper  
ridurrel’impattoambientale.Perlosmaltimento,rivolgersiadundistributoreounaf liatopresentinelproprio  
paese.  
GliindirizzisonoelencatinelsitoWebEIZOriportatodiseguito.  
http://www.eizo.com  
PerinformazionisulriciclaggiopericlientiinSvizzera,consultareilsitoWebriportatodiseguito.  
http://www.swico.ch  
Återvinningsinformation  
Närdennaproduktkasserasskadenhanterasochåtervinnasenligtlandetsföreskrifterförattreducera  
miljöpåverkan.Närdukasserarproduktenskadukontaktaendistributörellerrepresentantidittland.  
KontaktadressernalistaspåEIZO-webbplatsennedan.  
http://www.eizo.com  
Appendix  
80  
 
Πληροφορίες ανακύκλωσης  
Τοπροϊόναυτό,όταναπορρίπτεται,πρέπεινασυλλέγεταικαιναανακυκλώνεταισύμφωναμετηνομοθεσία  
τηςχώραςσαςέτσιώστεναμηνεπιβαρύνειτοπεριβάλλον.Γιανααπορρίψετετοπροϊόν,επικοινωνήστεμε  
έναναντιπρόσωποήμιαθυγατρικήεταιρείαστηχώρασας.  
ΟιδιευθύνσειςεπικοινωνίαςαναγράφονταιστηντοποθεσίαwebτηςEIZOπαρακάτω.  
http://www.eizo.com  
Сведения по утилизации  
По истечении срока службы данного продукта его следует принести на сборный пункт и  
утилизироватьвсоответствиисдействующимипредписаниямиввашейстране,чтобыуменьшить  
вредноевоздействиенаокружающуюсреду.Преждечемвыброситьданныйпродукт,обратитеськ  
дистрибьюторуиливместноепредставительствокомпанииввашейстране.  
Контактныеадресаможнонайтинавеб-узлеEIZO.  
http://www.eizo.com  
Informatie over recycling  
Wanneeruditproductwiltweggooien,moethetuitmilieu-overwegingenwordenverzameldengerecycled  
volgensdebetreffendewetgevingvanuwland.Wanneeruditproductwiltweggooien,moetucontact  
opnemenmeteendistributeurofeenpartnerinuwland.  
DecontactadressenwordenvermeldopdevolgendeEIZO-website.  
http://www.eizo.com  
Informação sobre reciclagem  
Esteproduto,quandoodeitarfora,deveserrecolhidoerecicladodeacordocomalegislaçãodoseupaís  
parareduzirapoluição.Quandodeitarforaesteproduto,contacteumdistribuidorouuma lialnoseupaís.  
OsendereçosdecontactoestãolistadosnowebsitedoEIZO,abaixo.  
http://www.eizo.com  
Oplysninger om genbrug  
Detteproduktforventesvedbortskaffelseatbliveindsamletoggenbrugtioverensstemmelsemed  
lovgivningeniditlandforatreducerebelastningenafmiljøet.Nårdubortskafferdenneprodukt,skaldu  
kontakteendistributørellerettilknyttetselskabiditland.  
AdressernepåkontaktpersonerneerangivetpåEIZO’swebstednedenfor.  
http://www.eizo.com  
Kierrätystä koskevia tietoja  
Tuote tulee hävittää kierrättämällä maan lainsäädännön mukaisesti ympäristön kuormittumisen  
vähentämiseksi.Kunhävitättuotteen,otayhteyttäjälleenmyyjääntaitytäryhtiöönmaassasi.  
YhteystiedotlöytyvätEIZOnInternet-sivustolta.  
http://www.eizo.com  
Wykorzystanie surowców wtórnych  
Tenproduktpozużyciupowinienbyćzbieranyiprzetwarzanyzgodniezkrajowymiprzepisamidotyczącymi  
ochronyśrodowiska.Wyrzucająctenprodukt,należyskontaktowaćsięzlokalnymdystrybutoremlub  
partnerem.Adresykontaktowemożnaznaleźćwewskazanejponiżejwitrynieinternetowej rmyEIZO.  
http://www.eizo.com  
Appendix  
81  
Informace o recyklaci  
Přilikvidaciproduktumusíbýtproduktvyzvednutarecyklovánpodlezákonůpříslušnézemě,aby  
nedocházelokzatěžováníživotníhoprostředí.Zbavujete-liseproduktu,kontaktujtedistributoranebo  
pobočkuvesvézemi.KontaktníadresyjsouuvedenynanásledujícíwebovéstráncespolečnostiEIZO.  
http://www.eizo.com  
Ringlussevõtu alane teave  
Keskkonnakoormusevähendamisekstulekskasutatudtootedkokkukogudajavõttaringlussevastavaltteie  
riigiseadustele.Kuikõrvaldatekäesolevatoote,võtkepalunühendustturustajavõi liaaligaomariigis.  
KontaktisikudontoodudEIZOveebileheljärgmiselaadressil:  
http://www.eizo.com  
Újrahasznosítási információ  
Jelenterméket,amikoreldobjuk,azilletőországtörvényeialapjánkellösszegyűjteniésújrahasznosítani,  
hogycsökkentsükakörnyezetterhelését.Amikoreztaterméketeldobja,kérjüklépjenkapcsolatbaegy  
országonbelüliforgalmazóvalvagytársvállalkozással.  
AkapcsolatcímeiazEIZOalábbiweboldalántalálhatókfelsorolva:  
http://www.eizo.com  
Podatki o recikliranju  
Obkoncuuporabeodsluženizdelekizročitenazbirnomestozarecikliranjevskladuzokoljevarstveno  
zakonodajovašedržave.Prosimo,dasepriodstranjevanjuizdelkaobrnetenalokalnegadistributerjaali  
podružnico.  
KontaktninaslovisoobjavljeninaspodajnavedenihspletnihstranehEIZO:  
http://www.eizo.com  
Informácie o recyklácii  
Prilikvidáciimusíbyťtentovýrobokrecyklovanývsúladeslegislatívouvašejkrajiny,abysaznížilozaťaženie  
životnéhoprostredia.Keďsachcetezbaviťtohtovýrobku,kontaktujteprosímdistribútoraalebopobočkuvo  
vašejkrajine.  
Zoznamkontaktnýchadriesjeuvedenýnanasledovnejwebovejstránke rmyEIZO:  
http://www.eizo.com  
Pārstrādes informācija  
Utilizējotšoproduktu,tāsavākšanaunpārstrādeveicamaatbilstošijūsuvalstslikumdošanasprasībām  
attiecībāuzslodzesuzvidisamazināšanu.Laiveiktušīproduktautilizāciju,sazinietiesarizplatītājuvai  
pārstāvniecībujūsuvalstī.  
KontaktadresesirnorādītaszemākminētajāEIZOtīmekļavietnē.  
http://www.eizo.com  
Informacija apie grąžinamąjį perdirbimą  
Šalinant(išmetant)šiuosgaminiusjuosreikiasurinktiirperdirbtigrąžinamuojubūdupagaljūsųšaliesteisės  
aktus,siekiantsumažintiaplinkosteršimą.Kaireikiaišmestišįgaminį,kreipkitėsįjūsųšalyjeveikiančią  
gaminiųpardavimoatstovybęarbajos lialą.  
KontaktiniaiadresatainurodytiEIZOinternetosvetainėje.  
http://www.eizo.com  
Appendix  
82  
Информация относно рециклиране  
Приизхвърлянетонатозипродуктсепредлагасъбиранетоирециклиранетомусъобразнозаконитена  
вашатастраназадасенамализамърсяванетонаоколнатасреда.Когатоискатедасеосвободитеот  
тозипродукт,молясвържетесестърговскиямупредставителилисъссъответнитеорганиотговарящи  
затовавъввашатастрана.  
ДаннитезавръзкаснассаописанинаследнияИнтернетсайтнаEIZO:  
http://www.eizo.com  
Informaţie referitoare la reciclare  
Acestprodus,cânddebarasat,trebuiecolectatşireciclatconformlegislaţieiţăriirspectivecasăreducem  
sarcinamediului.Cândsedebaraseazădeacestprodus,vărugămsăcontactaţiundistribuitorsauuna liat  
alţăriirespective.  
AdreseledecontactlegăsiţipepaginadewebalEIZO:  
http://www.eizo.com  
Geri Dönüşüm Bilgisi  
Buürünün,atılacağızaman,ülkenizinçevrekirliliğininazaltılmasıkonusundakimevzuatınagöretoplanması  
veyenidendeğerlendirilmesigerekmektedir.Ürünüatacağınızzamanlütfenülkenizdekibirdistribütörveya  
ilgilikuruluşlatemasageçiniz.  
İrtibatadresleriaşağıdakiEIZOwebsitesindeverilmiştir.  
http://www.eizo.com  
Appendix  
83  
China Measures for RoHS Compliance in ChinaRoHS  
关于电子信息产品污染控制标识  
本标识根据「电子信息产品污染控制管理办法」，适用于在中华人民共和国销售的电子信息产品。标识中央的  
数字为环保使用期限的年数。只要您遵守该产品相关的安全及使用注意事项，在自制造日起算的年限内，不会  
产生对环境污染或人体及财产的影响。上述标识粘贴在机器背面。  
•
有毒有害物质或元素的名称及含量  
部件名称  
有毒有害物质或元素  
铅
（Pb）  
×
汞
（Hg）  
○
镉
（Cd）  
○
六价铬  
（Cr（VI））  
多溴联苯  
（PBB）  
多溴二苯醚  
（PBDE）  
印刷电路板  
机箱  
○
○
○
○
○
○
○
○
○
○
○
○
○
×
○
○
○
○
液晶显示器  
其他  
×
○
○
○：表示该有毒有害物质在该部件所有均质材料中的含量均在SJ/T 11363-2006规定的限量要求以下。  
×：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出SJ/T 11363-2006规定的限量要求。  
(企业可在此处,根据实际情況对上表中打“×” 的技术原因进行进一步说明)  
Appendix  
84  
 
8th Edition-August, 2013  
03V24034H1  
Copyright © 2012-2013 EIZO Corporation All rights reserved.  
(U.M-EV2416W)  

HP Hewlett Packard HP Essential P221 21 5 C9E49A8#ABA User Manual
HP Hewlett Packard Hewlett Packard Computer Monitor CQ1859E User Manual
Extron electronic DVI Output Card User Manual
EverFocus ENVS1600 User Manual
Elo TouchSystems Toucmonitor User Manual
Elo TouchSystems ENTUITIVE TOUCHMONITOR ET1745C User Manual
Cypress CY8C20x46 User Manual
Asus Widescreen Lcd Monitor VE228 User Manual
Asus LED Monitor VE247H User Manual
Asus Computer Hardware M2V890 User Manual