Dialogic Brooktrout 931 107 05 User Manual

6. Replace the cover.  
System Requirements  
This board must be installed in an enclosure that  
meets the following specifications:  
Setting Termination Jumpers  
Before installing your board, set termination for the  
BRI line if necessary. See Figure 5 for the location of  
the termination switches.  
7. Turn on your computer.  
Note: Dialogic® Brooktrout® boards should not be present in the  
computer during the installation of any operating system.  
The operating system might misinterpret the board as being  
some other device, with unpredictable consequences.  
Š
Š
A Pentium or later host processor  
A PCI bus slot that runs at least 33 MHz and is  
32 or 64 bits wide. See Recognizing PCI Slots for  
more information.  
Recognizing PCI Slots  
The PCI connectors in the computer chassis usually  
appear as white slots. The TruFax® BRI board has a  
PCI board edge connector. It can be inserted into any  
of the PCI slots shown in Figure 3.  
Set jumpers as follows (See Figure 2 for details):  
Š
Š
Š
Temperature: 0 C - 50 C  
Humidity: 10% - 95% (non-condensing)  
Power Requirements:  
Installing the Dialogic®  
Brooktrout® TruFax® BRI  
PCI Board  
Board  
+5 V +3.3 V +12 V -12 V Total Power  
0.8A 0A 0A 0A 4.0 W  
0.9A 0A 0A 0A 4.5 W  
Single channel  
Dual channel  
Jumper is removed  
Jumper is in place  
Universal PCI Board Edge Connector  
Part Number: 931-107-05  
(ISDN BRI line is not terminated)  
(ISDN BRI line is terminated)  
The Dialogic® Brooktrout® TruFax® BRI  
(Basic Rate Interface ISDN) PCI boards are half-  
sized, single-slot PCI-bus compatible fax processing  
boards. They provide the following:  
3.3V 32-Bit Connector  
Figure 2. Termination Jumpers  
The following is also required:  
Telephone service: BRI interface  
5V 32-Bit Connector  
3.3V 64-Bit Connector  
Š
Š
Š
Š
When the jumpers are removed from both  
switches for the appropriate port, there is no  
termination.  
When jumpers are present, the lines are  
terminated with 100 ohms (this is how the boards  
are shipped).  
Š
Š
On-board BRI connections  
Up to four V.17 fax channels per board  
5V 64-Bit Connector  
Setting the Module Number  
Set each board to a unique module number to easily  
identify the resources associated with a specific board  
in a multi-board system.  
Insert the connector into any of these slots.  
The TruFax® BRI PCI Series boards can be used in  
either 3.3V or 5V bus (signaling) slots.  
Figure 3. PCI Slots  
Dialogic does not support any configuration  
except the two illustrated in Figure 2.  
You need a fax application to use a TruFax® BRI  
board. Dialogic does not provide the application or a  
driver for this board. A driver comes with the  
application that you purchase.  
Use the SW-1 rotary switch (Figure 1) to set a unique  
module number for each Dialogic® Brooktrout®  
board. See Figure 5 for the switch location. Select a  
number from 2 - F on the rotary switch. Settings 0 and  
1 are reserved and cannot be used.  
Connecting the Phone Service  
Brooktrout® Board  
The appropriate telephone service and hookups must  
be installed at your site in order to connect to  
telephone service. The following table shows the  
channel/port relationship:  
This installation guide provides information about:  
Š
System Requirements (including telephone  
service)  
To install your board:  
1. Turn off your PC and remove the cover.  
Š
Š
Š
Š
Š
Š
Š
Setting the Module Number  
Channel Number RJ-45 Port  
Type of Service  
Caution: A small amount of static electricity can destroy  
the sensitive components on your board. To prevent  
static damage, always connect yourself to ground using  
a ground strap before touching a circuit board. Handle  
boards only by the edges or metal mounting brackets  
and transport boards in an anti-static bag.  
Setting Termination Jumpers for the BRI Line  
Installing the Dialogic® Brooktrout® Board  
Recognizing PCI Slots  
Connecting the Phone Service  
Understanding LED Signals  
0
1
2
3
A
A
B
B
BRI S/T  
BRI S/T  
BRI S/T  
BRI S/T  
Figure 1. Rotary Switch (SW-1)  
2. If the system has a PCI expansion hold-down bar,  
remove it.  
Use the cable supplied with the board. Use these  
instructions to connect your board to BRI service:  
1. Plug one end of the cable into the telephone  
connector on the board.  
Using the Dialogic® Brooktrout® TruFax® BRI  
Board  
3. Locate a free PCI bus slot and remove the slot  
cover.  
Š
Getting Help  
4. Carefully align the board with the slot and firmly  
seat the board into the slot.  
Connect to Port A for channels 0 and 1 or to  
Port B for channels 2 and 3 (see Figure 5 to  
locate ports).  
5. Tighten the mounting bracket screw to secure the  
board to the chassis.  
2. Plug the other end into the wall connector for  
your BRI service.  
Warning: When installing the board, be sure that the  
mounting bracket is securely fastened to the chassis and  
the chassis is plugged into a grounded three prong plug.  
Improper chassis or bracket grounding can result in  
harmful or fatal electrical shock as well as component  
damage.  
Note: Port B is not present on the TruFax® BRI single port  
version.  
                 

HP Hewlett Packard Hewlett Packard Computer Monitor Q2010S User Manual
Hanns G Computer Monitor HL225 User Manual
GE MONOGRAM ZET857BBBB User Manual
GE 25846 User Manual
Emerson Dora the Explorer DTE316 User Manual
Elo TouchSystems 1847L User Manual
Compaq Q1859 User Manual
Avaya MERLIN MAGIX 4400D User Manual
Asus Computer Monitor VH226H User Manual1
Abit USA Corporation Computer Hardware IP 95 User Manual