VENT-FREE PROPANE/LP GAS FREESTANDING
PEDESTAL STOVE SYSTEM
OWNER’S OPERATION AND INSTALLATION MANUAL
S26PT
20,000 to 26,000 Btu/Hr
Thermostatically-
Controlled
WARNING:Improperinstallation,
WARNING: If the information in this manual is not
adjustment, alteration, service,
followed exactly, a fire or explosion may result caus-
ormaintenancecancauseinjury
ing property damage, personal injury, or loss of life.
orpropertydamage.Refertothis
manual for correct installation
andoperationalprocedures.For
assistance or additional infor-
mation consult a qualified in-
staller, service agency, or the
gas supplier.
— Donotstoreorusegasolineorotherflammable
vapors and liquids in the vicinity of this or any
other appliance.
— WHAT TO DO IF YOU SMELL GAS
•
•
Do not try to light any appliance.
Do not touch any electrical switch; do not
use any phone in your building.
Immediately call your gas supplier from a
neighbor’sphone.Followthegassupplier’s
instructions.
WARNING: This is an unvented
gas-firedheater.Itusesair(oxy-
gen) from the room in which it is
installed. Provisions for ad-
equate combustion and ventila-
tion air must be provided. Refer
to Air for Combustion and Ven-
tilation section on page 4 of this
manual.
•
•
If you cannot reach your gas supplier, call
the fire department.
— Installation and service must be performed by
a qualified installer, service agency, or the gas
supplier.
This appliance may be installed in an aftermarket*, permanently located, manufactured
(mobile) home, where not prohibited by local codes.
This appliance is only for use with the type of gas indicated on the rating plate. This
appliance is not convertible for use with other gases.
*Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer
Save this manual for future reference.
OWNER’S MANUAL
SAFETY
LOCAL CODES
UNPACKING
Install and use heater with care. Follow all 1. Remove top inner pack.
INFORMATION
local codes. In the absence of local codes, use
the latest edition of The National Fuel Gas
Code, ANSZ223.1,alsoknownasNFPA54*.
2. Tilt carton so that stove is upright.
3. Remove protective side packaging.
4. Slide stove out of carton.
Continued
15. Turn off and unplug heater and let cool
before servicing. Only a qualified ser-
vice person should service and repair
heater.
*Available from:
5. Remove protective plastic wrap.
American National Standards Institute, Inc.
1430 Broadway
6. Remove screen by lifting and then pull-
ing forward.
16. Operating heater above elevations of
4,500 feet could cause pilot outage.
New York, NY 10018
7. Remove log set by cutting plastic ties.
8. Carefully unwrap log.
National Fire Protection Association, Inc.
Batterymarch Park
17. Do not operate heater if any log is bro-
ken. Do not operate heater if a log is
chipped (dime-sized or larger).
9. Check for any shipping damage. If
stove or log is damaged, promptly in-
form dealer where you bought stove.
Quincy, MA 02269
18. To prevent performance problems, do This heater is designed for vent-free opera-
not use propane/LP fuel tank of less tion. State and local codes in some areas
than 100 lbs. capacity.
prohibit the use of vent-free heaters.
PRODUCT
FEATURES
SAFETY PILOT
PRODUCT
IDENTIFICATION
ThisheaterhasapilotwithanOxygenDeple-
tion Sensing (ODS) safety shutoff system.
The ODS/pilot is a required feature for vent-
free room heaters. The ODS/pilot shuts off
the heater if there is not enough fresh air.
PIEZO IGNITION SYSTEM
This heater has a piezo ignitor. This system
requires no matches, batteries, or other
sources to light heater.
Screen
Stove
Cabinet
Logs
Heater Controls
(Inside Door)
Figure 1 - Vent-Free Propane/LP Gas Stove
105684
3
VENT-FREE PROPANE/LP PEDESTAL STOVE
Confined and Unconfined Space
PROVIDING ADEQUATE
VENTILATION
AIR FOR
The National Fuel Gas Code, ANS Z223.1
defines a confined space as a space whose
volume is less than 50 cubic feet per 1,000
Btu per hour (4.8 m3 per kw) of the aggre-
gate input rating of all appliances installed
in that space and an unconfining space as a
space whose volume is not less than 50
cubicfeetper1,000Btuperhour(4.8m3 per
kw) of the aggregate input rating of all
appliances installed in that space. Rooms
communicating directly with the space in
whichtheappliancesareinstalled*,through
openings not furnished with doors, are con-
sidered a part of the unconfined space.
COMBUSTION AND
VENTILATION
The following are excerpts from National
Fuel Gas Code, NFPA 54/ANS Z223.1, Sec-
tion5.3, AirforCombustionandVentilation.
WARNING: This heater shall
notbeinstalledinaconfinedspace
or unusually tight construction
unless provisions are provided
foradequatecombustionandven-
tilation air. Read the following in-
structions to insure proper fresh
air for this and other fuel-burning
appliances in your home.
All spaces in homes fall into one of the three
following ventilation classifications:
1. Unusually Tight Construction
2. Unconfined Space
3. Confined Space
The information on pages 4 through 6 will
help you classify your space and provide
adequate ventilation.
This heater shall not be installed in a con-
fined space or unusually tight construction
unless provisions are provided for adequate
combustion and ventilation air.
Today’s homes are built more energy effi-
cient than ever. New materials, increased
insulation, and new construction methods
help reduce heat loss in homes. Home
owners weather strip and caulk around
windows and doors to keep the cold air out
andthewarmairin.Duringheatingmonths,
home owners want their homes as airtight
as possible.
Unusually Tight Construction
The air that leaks around doors and win-
dows may provide enough fresh air for
combustion and ventilation. However, in
buildings of unusually tight construction,
you must provide additional fresh air.
*Adjoiningroomsarecommunicatingonly
iftherearedoorlesspassagewaysorventila-
tion grills between them.
Unusually tight construction is de-
fined as construction where:
a. walls and ceilings exposed to the
outside atmosphere have a con-
tinuous water vapor retarder with
a rating of one perm (6 x 10-11 kg
per pa-sec-m2) or less with open-
ings gasketed or sealed and
While it is good to make your home energy
efficient,yourhomeneedstobreathe.Fresh
air must enter your home. All fuel-burning
appliances need fresh air for proper com-
bustion and ventilation.
Exhaust fans, heaters, clothes dryers, and
fuel burning appliances draw air from the
house to operate. You must provide ad-
equate fresh air for these appliances. This
will insure proper venting of vented fuel-
burning appliances.
b. weather stripping has been
added on openable windows and
doors and
c. caulking or sealants are applied
to areas such as joints around
window and door frames, be-
tween sole plates and floors, be-
tween wall-ceiling joints, be-
tween wall panels, at penetra-
tions for plumbing, electrical, and
gas lines, and at other openings.
If your home meets all of the three
criteria above, you must provide ad-
ditional fresh air. See Ventilation Air
From Outdoors, page 6.
If your home does not meet all of the
three criteria above, proceed to Deter-
mining Fresh-Air Flow For Heater
Location, page 5.
105684
4
OWNER’S MANUAL
AIR FOR
COMBUSTION AND
VENTILATION
Continued
DETERMINING FRESH-AIR FLOW FOR HEATER LOCATION
Determining if You Have a Confined or Unconfined Space
Use this worksheet to determine if you have a confined or unconfined space.
Space:Includestheroominwhichyouwillinstallheaterplusanyadjoiningroomswithdoorlesspassagewaysorventilationgrillsbetween
the rooms.
1. Determine the volume of the space (length x width x height).
Length x Width x Height = ____________________ cu. ft. (volume of space)
Example: Space size 20 ft. (length) x 16 ft. (width) x 8 ft. (ceiling height) = 2560 cu. ft. (volume of space)
If additional ventilation to adjoining room is supplied with grills or openings, add the volume of these rooms to the total volume of
the space.
2. Divide the space volume by 50 cubic feet to determine the maximum Btu/Hr the space can support.
_________________ (volume of space) ÷ 50 cu. ft. = (Maximum Btu/Hr the space can support)
Example: 2560 cu. ft. (volume of space) ÷ 50 cu. ft. = 51.2 or 51,200 (maximum Btu/Hr the space can support)
3. Add the Btu/Hr of all fuel burning appliances in the space.
Vent-free heater
Gas water heater*
Gas furnace
_________________Btu/Hr
_________________Btu/Hr
_________________Btu/Hr
_________________Btu/Hr
_________________Btu/Hr
_________________Btu/Hr
_________________Btu/Hr
Example:
Gas water heater
30,000
26,000
56,000
Btu/Hr
Btu/Hr
Btu/Hr
Vent-free heater +
Vented gas heater
Gas heater logs
Total
=
Other gas appliances* +
Total
=
* Do not include direct-vent gas appliances. Direct-vent draws combustion air from the outdoors and vents to the outdoors.
4. Compare the maximum Btu/Hr the space can support with the actual amount of Btu/Hr used.
_________________ Btu/Hr (maximum the space can support)
_________________ Btu/Hr (actual amount of Btu/Hr used)
Example: 51,200 Btu/Hr (maximum the space can support)
56,000 Btu/Hr (actual amount of Btu/Hr used)
The space in the above example is a confined space because the actual Btu/Hr used is more than the maximum Btu/Hr the space can support.
You must provide additional fresh air. Your options are as follows:
A. Rework worksheet, adding the space of an adjoining room. If the extra space provides an unconfined space, remove door to adjoining
room or add ventilation grills between rooms. See Ventilation Air From Inside Building, page 6.
B. Vent room directly to the outdoors. See Ventilation Air From Outdoors, page 6.
C. Install a lower Btu/Hr heater, if lower Btu/Hr size makes room unconfined.
If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, the space is an unconfined space. You will need no
additional fresh air ventilation.
WARNING: If the area in which the heater may be operated is smaller than that defined as an unconfined space
or if the building is of unusually tight construction, provide adequate combustion and ventilation air by one of
the methods described in the National Fuel Gas Code, ANS Z223.1, Section 5.3 or applicable local codes.
Continued
105684
5
VENT-FREE PROPANE/LP PEDESTAL STOVE
AIR FOR
12"
COMBUSTION AND
VENTILATION
Ventilation
Continued
Ventilation Grills
Into Adjoining Room,
Option 2
Grills
Into Adjoining
Room,
Or
VENTILATION AIR
Remove
Door into
Adjoining
Room,
Option
3
Option 1
Ventilation Air From Inside
Building
Thisfreshairwouldcomefromanadjoining
unconfined space. When ventilating to an
adjoining unconfined space, you must pro-
vide two permanent openings: one within
12" of the ceiling and one within 12" of the
floor on the wall connecting the two spaces
(see options 1 and 2, Figure 2). You can also
remove door into adjoining room (see op-
tion 3, Figure 2). Follow the National Fuel
Gas Code, NFPA 54/ANS Z223.1, Section
5.3, Air for Combustion and Ventilation for
required size of ventilation grills or ducts.
12"
Figure 2 - Ventilation Air from Inside Building
WARNING: Rework work-
sheet, adding the space of the
adjoining unconfined space. The
combined spaces must have
enough fresh air to supply all
appliances in both spaces.
Ventilated
Outlet
Attic
Air
Outlet
Air
To Attic
Ventilation Air From Outdoors
Provide extra fresh air by using ventilation
grills or ducts. You must provide two per-
manent openings: one within 12" of the
ceiling and one within 12" of the floor.
Connect these items directly to the outdoors
orspacesopentotheoutdoors.Thesespaces
include attics and crawl spaces. Follow the
National Fuel Gas Code, NFPA 54/ANS
Z223.1,Section5.3,AirforCombustionand
Ventilation for required size of ventilation
grills or ducts.
To
Crawl
Space
Inlet
Air
Ventilated
Crawl Space
Inlet Air
Figure 3 - Ventilation Air from Outdoors
IMPORTANT: Do not provide openings
for inlet or outlet air into attic if attic has
a thermostat-controlled power vent.
Heated air entering the attic will activate
the power vent.
105684
6
OWNER’S MANUAL
IMPORTANT:Vent-freeheatersaddmois- Carefullyfollowtheinstructionsbelow.This
ture to the air. Although this is beneficial, stove is a freestanding unit designed to set
installing heater in rooms without enough directly on the floor. IMPORTANT: You
ventilation air may cause mildew to form must maintain minimum wall and ceiling
from too much moisture. See Air for Com- clearances during installation. The mini-
bustion and Ventilation, pages 4 through 6. mum clearances are shown in Figure 4.
INSTALLATION
NOTICE: This heater is intended
foruseassupplementalheat.Use
this heater along with your pri-
mary heating system. Do not in-
stall this heater as your primary
heat source. If you have a central
heating system, you may run
system’scirculatingblowerwhile
using heater. This will help circu-
late the heat throughout the
house. In the event of a power
outage, you can use this heater
as your primary heat source.
Measure from outermost point of stove top.
CHECK GAS TYPE
Minimum Wall and Ceiling
Clearances (see Figure 4)
A. Clearances from outermost point of
stove top to any combustible side wall
should not be less than 12 inches.
Useonlypropane/LPgas.Ifyourgassupply
is not propane/LP gas, do not install heater.
Call dealer where you bought heater for
proper type heater.
CLEARANCES TO
COMBUSTIBLES
(Vent-Free Operation Only)
B. Clearances from outermost point of
stove top to any combustible back wall
should not be less than 6 inches (In-
cludes corner installations).
WARNING: A qualified ser-
vice person must install heater.
Follow all local codes.
C. Clearances from the stove top to the
ceiling should not be less than 48
inches.
WARNING:Maintainthemini-
mum clearances. If you can, pro-
vide greater clearances from
floor, ceiling, and adjoining side
and back walls.
WARNING: Never install the
heater
Ceiling
• in a bedroom or bathroom
• in a recreational vehicle
• where curtains, furniture,
clothing, or other flammable
objectsarelessthan42inches
from the front, top, or sides of
the heater
Front View
48"
Minimum
12"
Minimum
12"
Minimum
Side Wall
Side Wall
• in high traffic areas
• in windy or drafty areas
CAUTION: This heater cre-
ates warm air currents. These
currents move heat to wall sur-
faces next to heater. Installing
heater next to vinyl or cloth wall
coverings or operating heater
where impurities (such as to-
bacco smoke, aromatic candles,
cleaning fluids, oil or kerosene
lamps, etc.) in the air exist, may
discolor walls.
Top View
Back Wall
6
"
Minimum
Side View
Ceiling
12
"
12
"
Minimum
Minimum
Side Wall
Side Wall
48"
Minimum
Corner
Wall
Back Wall
6"
Minimum
6
"
Front of
Minimum
Stove Unit
6
"
Wall
Minimum
Floor
Figure 4 - Minimum Clearance to Walls and Ceiling
Continued
105684
7
VENT-FREE PROPANE/LP PEDESTAL STOVE
Theinstallermustsupplyanexternalregulator. Installation must include an equipment
The external regulator will reduce incoming shutoff valve, union, and plugged 1/8" NPT
gas pressure. You must reduce incoming gas tap. Locate NPT tap within reach for test
INSTALLATION
Continued
pressure to between 11 and 14 inches of water. gauge hook up. NPT tap must be upstream
If you do not reduce incoming gas pressure, from heater (see Figure 7).
CONNECTING TO GAS
SUPPLY
heater regulator damage could occur. Install
IMPORTANT: Install equipment shutoff
external regulator with the vent pointing down
valve in an accessible location. The equip-
WARNING: A qualified service
personmustconnectheatertogas
supply. Follow all local codes.
as shown in Figure 6. Pointing the vent down
protects it from freezing rain or sleet.
ment shutoff valve is for turning on or
shutting off the gas to the appliance.
Apply pipe joint sealant lightly to male
threads. This will prevent excess sealant
from going into pipe. Excess sealant in pipe
could result in clogged heater valves.
WARNING: Never connect
heater to private (non-utility) gas
wells. This gas is commonly
known as wellhead gas.
CAUTION: Never connect
heater directly to the propane/LP
supply. This heater requires an ex-
ternal regulator (not supplied). In-
stalltheexternalregulatorbetween
the heater and propane/LP supply.
CAUTION:Usepipejointseal-
ant that is resistant to liquid pe-
troleum (LP) gas.
CAUTION: Use only new,
black iron or steel pipe. Inter-
nally-tinned copper tubing may
be used in certain areas. Check
yourlocalcodes. Usepipeof1/2"
diameter or greater to allow
proper gas volume to heater. If
pipe is too small, undue loss of
pressure will occur.
Installation Items Needed
We recommend that you install a sediment
trap in supply line as shown in Figure 7.
Locate sediment trap where it is within
reach for cleaning. Install in piping system
betweenfuelsupplyandheater.Locatesedi-
ment trap where trapped matter is not likely
to freeze. A sediment trap traps moisture
and contaminants. This keeps them from
going into heater controls. If sediment trap
is not installed or is installed wrong, heater
may not run properly.
Beforeinstallingheater,makesureyouhave
the items listed below.
• piping (check local codes)
• sealant (resistant to propane/LP gas)
• equipment shutoff valve *
• test gauge connection *
• sediment trap
• tee joint
• pipe wrench
Propane/LP
Supply Tank
External
Regulator
*
An CSA design-certified equipment
shutoff valve with 1/8" NPT tap is an ac-
ceptable alternative to test gauge connec-
tion. Purchase the optional CSA design-
certifiedequipmentshutoffvalvefromyour
dealer. See Accessories, page 22.
CAUTION: Avoid damage to
regulator.Holdgasregulatorwith
wrenchwhenconnectingittogas
piping and/or fittings.
Vent
Pointing
Down
Figure 6 - External Regulator With Vent
Pointing Down
Back View
From External
Regulator (11"
W.C.** to 14"
W.C. Pressure)
CSA Design-Certified
Equipment Shutoff Valve
With 1/8" NPT Tap*
Approved
Side View
Flexible Gas
Hose (if allowed
by local codes)
Front
of
Stove
Unit
Tee
Joint
Sediment
Trap
3" Minimum
Gas Regulator
Inlet Connection
Pipe
Gas
Regulator
Nipple
of Heater
Cap
Figure 5 - Gas Regulator Location and
Gas Line Access Into Stove Cabinet
Figure 7 - Gas Connection
* Purchase the optional CSA design-certified equipment shutoff valve from your dealer.
See Accessories, page 22.
**Minimum inlet pressure for purpose of input adjustment.
105684
8
OWNER’S MANUAL
Test Pressures Equal To or Less Than
1/2 PSIG (3.5 kPa)
Pressure Testing Heater Gas
Connections
1. Open equipment shutoff valve (see Fig-
ure 8).
INSTALLATION
Continued
1. Close equipment shutoff valve (see Fig-
ure 8).
CHECKING GAS
CONNECTIONS
2. Pressurize supply piping system by either
using compressed air or opening propane/
LP supply tank valve.
2. Open propane/LP supply tank valve.
3. Make sure control knob of heater is in
the OFF position.
WARNING: Test all gas pip-
ing and connections for leaks
after installing or servicing. Cor-
rect all leaks at once.
3. Check all joints from gas meter to equip-
ment shutoff valve (see Figure 9).Apply
mixture of liquid soap and water to gas
joints. Bubbles forming show a leak.
4. Check all joints from equipment shutoff
valve to control valve (see Figure 9).
Apply mixture of liquid soap and wa-
ter to gas joints. Bubbles forming show
a leak.
4. Correct all leaks at once.
WARNING:Neveruseanopen
flame to check for a leak. Apply a
mixture of liquid soap and water
toalljoints.Bubblesformingshow
a leak. Correct all leaks at once.
Open
5. Correct all leaks at once.
6. Light heater (see Operating Heater,
pages 11 and 12). Check all other in-
ternal joints for leaks.
Equipment
Shutoff
Valve
7. Turn off heater (see To Turn Off Gas to
Appliance, page 12).
Closed
CAUTION: Make sure exter-
nal regulator has been installed
between propane/LP supply and
heater.SeeguidelinesunderCon-
necting to Gas Supply, page 8.
Figure 8- Equipment Shutoff Valve
Equipment Shutoff Valve
Propane/LP
Supply Tank
Pressure Testing Gas Supply
Piping System
Test Pressures In Excess Of 1/2 PSIG
(3.5 kPa)
1. Disconnect heater with its appliance
main gas valve (control valve) and
equipment shutoff valve from gas sup-
ply piping system. Pressures in excess
of 1/2 psig will damage heater regulator.
2. Cap off open end of gas pipe where
equipment shutoff valve was connected.
3. Pressurize supply piping system by ei-
ther using compressed air or opening
propane/LP supply tank valve.
Control Valve Location
Figure 9 - Checking Gas Joints
4. Check all joints of gas supply piping
system. Apply mixture of liquid soap
and water to gas joints. Bubbles form-
ing show a leak.
5. Correct all leaks at once.
6. Reconnect heater and equipment
shutoff valve to gas supply. Check re-
connected fittings for leaks.
Continued
105684
9
VENT-FREE PROPANE/LP PEDESTAL STOVE
5. Install one plastic bushing provided in
INSTALLING BLOWER
ACCESSORY - GA3750
INSTALLATION
blower kit into the 1 1/2" hole in the left
rear of firebox floor. Access hole
through the rectangular opening in the
rear panel (see Figure 14).
Continued
Tools required: Phillips screwdriver
INSTALLING LOGS
NOTICE:Shutoffgasheaterduring
the following blower installation.
6. Remove the two blower mounting
brackets from the rear panel by remov-
ing two screws each (see Figure 15).
WARNING: Failure to position
thepartsinaccordancewiththese
diagrams or failure to use only
parts specifically approved with
this heater may result in property
damage or personal injury.
1. Remove top panel of stove by remov-
ing three screws from under top lip on
each side of stove (see Figure 12).
7. Attach the two mounting brackets to
blower housing using four screws pro-
vided in blower kit (2 for each bracket)
(see Figure 15). Tighten screws se-
curely. Place blower assembly tempo-
rarily on top of firebox.
2. Facing front of stove, carefully slide top
panel forward until it is completely re-
moved from stove (see Figure 12).
CAUTION:Afterinstallationand
periodicallythereafter,checktoen-
surethatnoflamecomesincontact
with any log. With the heater set to
High,checktoseeifflamescontact
any log. If so, reposition logs ac-
cording to the log installation in-
structions in this manual. Flames
contacting logs will create soot.
3. Disconnect power cord wires from blower
motor (if connected) (see Figure 13).
8. Working from the rear of the stove,
place entire power cord, including
speed control housing, in lower control
compartment.
4. Disconnect green ground wire from
blower housing (if connected) by re-
moving screw holding wire terminal
(see Figure 13).
9. Route ends of 3-wire power cord up from
the lower control compartment through
the plastic bushing, then up to the upper
cavity of stove (see Figure 16, page 11).
10. Attach the terminal ends of the white
and black power cord wires to the ter-
minals on the blower motor (see Fig-
ure 13). Push firmly.
Itisveryimportanttoinstallthelogsexactly
as instructed. Do not modify logs. Only use
logs supplied with heater.
Place one-piece log set on grate to fit as
illustrated in Figure 10. Make sure log sits
flat on firebox floor (see Figure 10).
IMPORTANT:Makesurelogdoesnotcover
any burner ports (see Figure 11).
11. Attach the terminal end of the green
power cord wire to the front tab of the
blower housing using screw provided
(see Figure 13).
Figure 12 - Removing Stove Top Panel
12. Using the four screws previously re-
moved, mount blower assembly to
stove by reattaching blower brackets to
rear panel (see Figure 15). Tighten
screws securely.
White Powercord Wire
Black Powercord Wire
One Piece
Log Set
Blower
Bracket
I
O
F
T
L
Screw
Green
Ground Wire
Blower
Figure 13 - Removing Wires from Blower
Firebox Floor
Figure 10 - Installing One-Piece Log Set
Burner Ports
One Piece Log Set
Figure 14 - Installing Bushing
Firebox Top
Figure 15 - Removing Blower Brackets
from Stove and Attaching to Blower
Figure 11 - Installing One-Piece Log set
(Top View)
105684
10
OWNER’S MANUAL
INSTALLATION
OPERATING HEATER
WARNING: ELECTRICAL
Continued
GROUNDING INSTRUCTIONS
Thisapplianceisequippedwitha
three-prong (grounding) plug for
your protection against shock
hazard and should be plugged
directly into a properly grounded
three-prong receptacle.
FOR YOUR SAFETY
READ BEFORE
LIGHTING
13. Install plastic control knob onto output
shaft of speed control housing (see Fig-
ure 16). Place speed control housing
just inside control compartment door
in front of stove (see Figure 17).
WARNING: If you do not fol-
low these instructions exactly, a
fireorexplosionmayresultcaus-
ing property damage, personal
injury or loss of life.
14. Using two screws provided in blower
kit, mount blower speed control hous-
ing to mounting tab in left side of lower
control compartment (see Figure 17).
19. Using speed control knob, turn blower
on and check for operation.
20. All remaining parts from blower kit
may be discarded.
15. Check to make sure that the power cord is
completelyclearofblowerwheelandthere
are no foreign objects in blower wheel.
A. This appliance has a pilot which must
be lighted by hand. When lighting the
pilot, follow these instructions exactly.
16. Carefully replace stove top panel.Align
holes and replace six screws removed
in step 1, page 10.
B. BEFORE LIGHTING smell all
around the appliance area for gas. Be
sure to smell next to the floor because
some gas is heavier than air and will
settle on the floor.
17. Peel off the backing paper and stick the
supplied wiring diagram decal on the
stove floor as shown in Figure 16.
Blower Speed
Control Housing
WHATTO DO IFYOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do
not use any phone in your building.
• Immediately call your gas supplier
from a neighbor’s phone. Follow
the gas supplier’s instructions.
18. Plugpowercordintoaconvenient3-prong
grounded wall receptacle near the stove.
Figure17-InstallingBlowerControlHousing
• If you cannot reach your gas sup-
plier, call the fire department.
C. Use only your hand to push in or turn
the gas control knob. Never use tools.
If the knob will not push in or turn
by hand, don’t try to repair it, call a
qualified service technician or gas
supplier. Force or attempted repair
may result in a fire or explosion.
WARNING: Never attempt to service heater while it
is plugged in, operating, or hot. Burns and electrical
shock could result. Only a qualified service person
should service or repair heater.
If any of the original wire as supplied with the appliance must be
replaced, it must be replaced with 105°C wire or it’s equivalent.
WARNING: Label all wires prior to disconnection
when servicing controls. Wiring errors can cause im-
proper and dangerous operation. Verify proper opera-
tion after servicing.
D. Do not use this appliance if any part
has been under water. Immediately call
a qualified service technician to inspect
the appliance and to replace any part
of the control system and any gas con-
trol which has been under water.
Power
Cord
Variable
Fan Switch
Off
On
110/115
V.A.C.
Blower
Motor
Black
Green
White
Black
White
Wiring
Diagram
Decal
120 Vac. 60 Hz. . 78 Amps
Speed Control
Control
Knob
DESA International, Bowling Green, KY
101584-05
Housing
Figure 16 - Routing Power Cord
Continued
105684
11
VENT-FREE PROPANE/LP PEDESTAL STOVE
7. Keep control knob pressed in for 30
MANUAL LIGHTING
PROCEDURE
1. Follow steps 1 through 5 under Light-
OPERATING
seconds after lighting pilot. After 30
seconds, release control knob.
• Ifcontrolknobdoesnotpopoutwhen
released, contact a qualified service
person or gas supplier for repairs.
HEATER
Continued
LIGHTING
ing Instructions.
2. Depress control knob and light pilot
with match.
INSTRUCTIONS
Note: If pilot goes out, repeat steps 3
through 7.This heater has a safetyinter- 3. Keep control knob pressed in for 30
NOTICE: During initial operation
of new heater, burning logs will
give off a paper-burning smell.
Orange flame will also be present.
Open a window to vent smell. This
will only last a few hours.
lock system.Wait one (1) minute for sys-
tem to reset before lighting pilot again.
seconds after lighting pilot. After 30
seconds, release control knob. Now
follow step 8 in column 2.
8. Turn control knob counterclockwise
C-clockwise
to desired heating level. The
burners should light. Set control knob
to any heat level between HI and LO.
INSPECTING
BURNERS
Pilot Burner
1. STOP! Read the safety information,
page 11, column 3.
Thermocouple
Check pilot flame pattern and burner flame
patterns often.
2. Make sure equipment shutoff valve
is fully open.
PILOT FLAME PATTERN
3. Turn control knob clockwise
to the OFF position.
Clockwise
Figure 20 shows a correct pilot flame pat-
tern.Figure21showsanincorrectpilotflame
pattern.Theincorrectpilotflameisnottouch-
ing the thermocouple. This will cause the
thermocouple to cool. When the thermo-
couple cools, the heater will shut down.
4. Wait five (5) minutes to clear out any
gas. Then smell for gas, including
near the floor. If you smell gas,
STOP! Follow “B” in the safety in-
formation, page 11, column 3. If you
don’t smell gas, go to the next step.
Figure 19 - Pilot
CAUTION:Donottrytoadjust
heatinglevelsbyusingtheequip-
ment shutoff valve.
If pilot flame pattern is incorrect, as shown
in Figure 21
5. Turn control knob counterclockwise
TO TURN OFF GAS
TO APPLIANCE
to the PILOT position.
Press in control knob for five (5) sec-
onds (see Figure 18).
C-clockwise
• turn heater off (see To Turn Off Gas to
Appliance)
Shutting Off Heater
Turn control knob clockwise
the OFF position.
• see Troubleshooting, pages 14 through 16
Note: You may be running this
heater for the first time after hook-
ing up to gas supply. If so, the con-
trol knob may need to be pressed in
for 30 seconds or less. This will allow
air to bleed from the gas system.
to
Clockwise
Pilot Burner
Shutting Off Burners Only (pilot
stays lit)
Turn control knob clockwise
the PILOT position.
Thermocouple
to
Clockwise
6. With control knob pressed in, press
and release ignitor button. This will
light pilot. The pilot is attached to the
front burner. If needed, keep press-
ing ignitor button until pilot lights.
THERMOSTAT CONTROL
OPERATION
Figure 20 - Correct Pilot Flame Pattern
Pilot Burner
The thermostat control knob can be set to
any comfort level between Hi and Lo. The
thermostatwillgraduallymodulatetheheat
output and flame height from higher to
lower settings, or pilot, in order to maintain
the comfort level you select. The ideal com-
fort setting will vary by household depend-
ing upon the amount of space to be heated,
the output of the central heating system, etc.
Note: If pilot does not stay lit, con-
tact a qualified service person or gas
supplier for repairs. Until repairs are
made, light pilot with match. To light
pilot with match, see Manual Light-
ing Procedure.
Thermocouple
Control Knob
Ignitor Button
Figure 21 - Incorrect Pilot Flame Pattern
Note: Selecting the Hi setting with the
control knob will cause the burners to
remainfullyon,withoutmodulatingdown
in most cases.
Figure 18 - Control Knob and Ignitor
Button Location
105684
12
OWNER’S MANUAL
CLEANING BURNER
INJECTOR HOLDER AND
PILOT AIR INLET HOLE
Burner
Injector
INSPECTING
Tube
Holder
BURNERS
Continued
The primary air inlet holes allow the proper
amount of air to mix with the gas. This pro-
videsacleanburningflame. Keeptheseholes
clear of dust, dirt, lint, and pet hair. Clean
these air inlet holes prior to each heating
season.Blockedairholeswillcreatesoot.We
recommendthatyoucleantheuniteverythree
months during operation and have heater in-
spected yearly by a qualified service person.
BURNER FLAME PATTERN
Primary Air
Inlet Holes
Figure 22 shows a correct burner flame pat-
tern. Figure 23 shows an incorrect burner
flame pattern. If burner flame pattern is
incorrect,
Figure 24 - Injector Holder On Outlet
Burner Tube
Ports/Slots
• turn heater off (see To Turn Off Gas to
Appliance, page 12)
Burner
Tube
• see Troubleshooting, pages 14 through 16
Wealsorecommendthatyoukeeptheburner
tubeandpilotassemblycleanandfreeofdust
and dirt. To clean these parts we recommend
using compressed air no greater than 30 PSI.
Yourlocalcomputerstore,hardwarestore,or
home center may carry compressed air in a
can. You can use a vacuum cleaner in the
blow position. If using compressed air in a
can, please follow the directions on the can.
If you don't follow directions on the can, you
could damage the pilot assembly.
Approx. 3-6" Above
Top of Logs
Pilot
Assembly
Pilot Air
Inlet
Hole
Figure 22 - Correct Flame Pattern with
Control Knob Set to High Flame.
Figure 25 - Pilot Inlet Air Hole
1. Shut off the unit, including the pilot.
Allow the unit to cool for at least thirty
minutes.
More Than 8"
Above Top of Logs
CABINET
Air Passageways
• Use a vacuum cleaner or pressurized air
to clean.
2. Inspect burner, pilot, and primary air
inlet holes on injector holder for dust
and dirt (see Figure 24).
Exterior
3. Blow air through the ports/slots and
holes in the burner.
• Use a soft cloth dampened with a mild
soap and water mixture. Wipe the cabi-
net to remove dust.
4. Check the injector holder located at the
end of the burner tube again. Remove any
large particles of dust, dirt, lint, or pet hair
with a soft cloth or vacuum cleaner nozzle.
Figure 23 - Incorrect Flame Pattern with
Control Knob Set to High Flame
LOGS
• If you remove logs for cleaning, refer to
Installing Logs, page 10, to properly re-
place logs.
5. Blow air into the primary air holes on
the injector holder.
CLEANING AND
MAINTENANCE
6. In case any large clumps of dust have
now been pushed into the burner repeat
steps 3 and 4.
• Replace log(s) if broken or chipped
(dime-sized or larger).
MAIN BURNER
WARNING: Turn off heater
and let cool before cleaning.
Clean the pilot assembly also. A yellow tip on
thepilotflameindicatesdustanddirtinthepilot
assembly. There is a small pilot air inlet hole
about two inches from where the pilot flame
comesoutofthepilotassembly(seeFigure25).
Withtheunitoff,lightlyblowairthroughtheair
inlet hole. You may blow through a drinking
straw if compressed air is not available.
Periodically inspect all burner flame holes
with the heater running. All slotted burner
flame holes should be open with yellow
flame present. All round burner flame holes
should be open with a small blue flame
present. Some burner flame holes may be-
comeblockedbydebrisorrust,withnoflame
present. If so, turn off heater and let cool.
Either remove blockage or replace burner.
Blocked burner flame holes will create soot.
CAUTION: You must keep
control areas, burner, and circu-
lating air passageways of heater
clean. Inspect these areas of
heater before each use. Have
heaterinspectedyearlybyaquali-
fied service person. Heater may
needmorefrequentcleaningdue
to excessive lint from carpeting,
bedding material, pet hair, etc.
Reviewyourvideoincludedwithyourheater
for additional cleaning instructions.
105684
13
VENT-FREE PROPANE/LP PEDESTAL STOVE
TROUBLESHOOTING
CAUTION: Never use a wire,
WARNING: Turn off heater
andletcoolbeforeservicing.Only
aqualifiedservicepersonshould
service and repair heater.
needle, or similar object to clean
ODS/pilot.ThiscandamageODS/
pilot unit.
Note: For additional help, visit DESA
International’stechnicalservicewebsite
Note:Alltroubleshootingitemsarelistedin
order of operation.
OBSERVED PROBLEM
POSSIBLE CAUSE
REMEDY
When ignitor button is pressed, there is no 1. Ignitor electrode not connected to igni- 1. Reconnect ignitor cable
spark at ODS/pilot
tor cable
2. Ignitor cable pinched or wet
2. Free ignitor cable if pinched by any
metal or tubing. Keep ignitor cable dry
3. Tighten nut holding piezo ignitor to base
panel of log set. Nut is located behind
base panel
3. Piezo ignitor nut is loose
4. Broken ignitor cable
4. Replace ignitor cable
5. Bad piezo ignitor
5. Replace piezo ignitor
6. Ignitor electrode broken
7. Ignitor electrode positioned wrong
6. Replace piezo ignitor
7. Replace piezo ignitor
When ignitor button is pressed, there is 1. Gas supply turned off or equipment 1. Turn on gas supply or open equipment
spark at ODS/pilot but no ignition
shutoff valve closed
shutoff valve
2. Control knob not in PILOT position
2. Turn control knob to PILOT position
3. Control knob not pressed in while in 3. Press in control knob while in PILOT
PILOT position
position
4. Air in gas lines when installed
4. Continue holding down control knob.
Repeat igniting operation until air is re-
moved
5. Depleted gas supply
6. ODS/pilot is clogged
5. Contact local propane/LP gas company
6. Clean ODS/pilot (see Cleaning and
Maintenance, page 13) or replace ODS/
pilot assembly
7. Gas regulator setting is not correct
7. Replace gas control
ODS/pilot lights but flame goes out when 1. Control knob not fully pressed in
1. Press in control knob fully
control knob is released
2. Control knob not pressed in long enough 2. After ODS/pilot lights, keep control
knob pressed in 30 seconds
3. Equipment shutoff valve not fully open 3. Fully open equipment shutoff valve
4. Pilot flame not touching thermocouple, 4. A) Contact local propane/LP gas company
which allows thermocouple to cool,
causing pilot flame to go out. This prob-
lem could be caused by one or both of
the following:
B) Clean ODS/pilot (see Cleaning and
Maintenance, page 13) or replace ODS/
pilot assembly
A) Low gas pressure
B) Dirty or partially clogged ODS/pilot
5. Thermocouple connection loose at con- 5. Hand tighten until snug, then tighten 1/4
trol valve
turn more
6. Thermocouple damaged
7. Control valve damaged
6. Replace thermocouple
7. Replace control valve
105684
14
OWNER’S MANUAL
TROUBLESHOOTING
Continued
OBSERVED PROBLEM
POSSIBLE CAUSE
REMEDY
Burner does not light after ODS/pilot is lit
1. Burner orifice clogged
1. Clean burner (see Cleaning and Mainte-
nance, page 13) or replace burner orifice
2. Contact local propane/LP gas company
2. Inlet gas pressure is too low
3. Burner orifice diameter is too small
3. Replace burner orifice
4. Thermopile leads disconnected or im- 4. Reconnect leads (see wiring diagram)
properly connected
5. Burners will not come on in remote position 5. Replace battery in transmitter and receiver
Delayed ignition burner
1. Manifold pressure is too low
2. Burner orifice clogged
1. Contact local propane/LP gas company
2. Clean burner (see Cleaning and Mainte-
nance, page 13) or replace burner orifice
Burner backfiring during combustion
1. Burner orifice is clogged or damaged
1. Clean burner (see Cleaning and Mainte-
nance, page 13) or replace burner orifice
2. Replace damaged burner
2. Damaged burner
3. Gas regulator defective
3. Replace gas control
Slight smoke or odor during initial operation 1. Not enough air
1. Check burner for dirt and debris. If found,
clean burner (see Cleaning and Mainte-
nance, page 13)
2. Gas regulator defective
2. Replace gas control
3. Residues from manufacturing processes 3. Problem will stop after a few hours of
and logs curing
operation
Moisture/condensation noticed on windows 1. Not enough combustion/ventilation air
1. Refer to Air for Combustion and Ventila-
tion requirements (page 4)
Heater produces a whistling noise when 1. Turning control knob to HI position when 1. Turn control knob to LO position and let
burner is lit
burner is cold
warm up for a minute
2. Air in gas line
2. Operate burner until air is removed from
line. Have gas line checked by local pro-
pane/LP gas company
3. Air passageways on heater blocked
3. Observe minimum installation clearances
(see pages 7 through 9)
4. Dirty or partially clogged burner orifice
4. Clean burner (see Cleaning and Mainte-
nance, page 13) or replace burner orifice
Dark residue on logs or inside of fireplace
1. Improper log placement
1. Properly locate logs (see Installing Logs,
page 10)
2. Drafts or other air currents affecting 2. Eliminate source of drafts around heater
flame pattern
3. Air holes at burner inlet blocked
3. Clean out air holes at burner inlet. Peri-
odically repeat as needed
4. Burner flame holes blocked
4. Remove blockage or replace burner
Whitepowderresidueformingwithinburner 1. When heated, vapors from furniture pol- 1. Turn heater off when using furniture pol-
box or on adjacent walls or furniture
ish, wax, carpet cleaners, etc. turn into
white powder residue
ish, wax, carpet cleaners, or similar
products
Continued
105684
15
VENT-FREE PROPANE/LP PEDESTAL STOVE
TROUBLESHOOTING
Continued
WARNING: If you smell gas
• Shut off gas supply.
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your
building.
• Immediatelycallyourgassupplierfromaneighbor’sphone.Followthe
gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
IMPORTANT: Operating heater where impurities in air exist may create odors. Cleaning
supplies, paint, paint remover, cigarette smoke, cements and glues, new carpet or textiles,
etc., create fumes. These fumes may mix with combustion air and create odors. These odors
will disappear over time.
POSSIBLE CAUSE
OBSERVED PROBLEM
REMEDY
1. Metal expanding while heating or con-
tracting while cooling
Heater produces a clicking/ticking noise
just after burner is lit or shut off
1. This is common with most heaters. If
noise is excessive, contact qualified ser-
vice person
1. Heater burning vapors from paint, hair
spray, glues, cleaners, chemicals, new
carpet, etc. (See IMPORTANT state-
ment above)
Heater produces unwanted odors
1. Open window and ventilate room. Stop
using odor causing products while heater
is running
2. Gas leak. SeeWarning statement at
top of page
2. Locate and correct all leaks (see Check-
ing Gas Connections, page 9)
1. Not enough fresh air is available
2. Low line pressure
3. ODS/pilot is partially clogged
Heater shuts off in use (ODS operates)
1. Open window and/or door for ventilation
2. Contact local propane/LP gas company
3. Clean ODS/pilot (see Cleaning and
Maintenance, page 13)
1. Gas leak. SeeWarning statement at
top of page
2. Control valve defective
Gas odor even when control knob is in OFF
position
1. Locate and correct all leaks (see Check-
ing Gas Connections, page 9)
2. Replace control valve
1. Foreign matter between control valve
and burner
Gas odor during combustion
1. Take apart gas tubing and remove for-
eign matter
2. Gas leak. SeeWarning statement at
top of page
2. Locate and correct all leaks (see Check-
ing Gas Connections, page 9)
1. Excessive line or manifold pressure
2. Dirty primary air holes
Burner flame is excessively large and is
very near or touches the top of firebox
1. Check manifold pressure and correct as
needed
2. Clean burner air holes (see Cleaning and
Maintenance, page13).
105684
16
OWNER’S MANUAL
SPECIFICATIONS
PARTS CENTRALS
These Parts Centrals are privately owned businesses. They have agreed to support our
customer’s needs by providing original replacement parts and accessories.
Btu (Variable)
Type Gas
20,000/26,000
Propane/LP Only
Piezo
Ignition
Baltimore Electric
1348 Dixwell Avenue
Hamden, CT 06514-0322
1-800-397-7553
203-248-7553
Parts Department
East Coast Energy Products
707 Broadway
W. Long Branch, NJ 07764-1542
732-870-8809
1-800-755-8809
Manifold Pressure
8" W.C.
Inlet Gas Pressure
(in. of water) *
Maximum
Minimum
Dimensions, Inches (H x W x D)
Stove
Carton
Weight, pounds
Stove
14"
11"
24 x 27 1/4 x 17 1/4
22 x 31 x 31 1/2
Portable Heater Parts
342 N. County Rd. 400 East
Valparaiso, IN 46383-9704
All States
219-462-7441
1-800-362-6951
Dayton Hardware
P.O. Box 275
North Dayton Station
Dayton, OH 45404-0275
All States
66 lbs.
80 lbs.
Shipping
937-258-3721
OH 1-800-762-3426
* For purposes of input adjustment
Halco Enterprises
208 Carter Drive, Unit 21
West Chester, PA 19382-4500
610-430-7717
1-800-368-0803
FBD
SERVICE HINTS
1349 Adams Street
Bowling Green, KY 42103-3414
270-846-1199
When Gas Pressure Is Too Low
• pilot will not stay lit
1-800-654-8534
Fax: 1-800-846-0090
• burners will have delayed ignition
• heater will not produce specified heat
• propane/LP gas supply may be low
Laporte’s Parts & Service
2444 N. 5th Street
Master Parts Dist.
1251 Mound Ave NW
Grand Rapids, MI 49504-2672
616-791-0505
1-800-446-1446
Fax: 616-791-8270
Hartsville, SC 29550-7704
803-332-0191
Parts Department
When Gas Quality Is Bad
• pilot will not stay lit
• burners will produce flames and soot
• heater will backfire when lit
Cans Unlimited, Inc.
P.O. Box 645
Taylor, SC 29687-0013
All States
803-879-3009
Youmayfeelyourgaspressureistoolowor
gas quality is bad. If so, contact your local
propane/LP gas supplier.
Washer Equipment Co.
1715 Main Street
1-800-845-5301
Kansas City, MO 64108-2195
KS, MO, AR
816-842-3911
TECHNICAL
SERVICE
You may have further questions about in-
stallation, operation, or troubleshooting. If
so, contact DESA International’s Technical
Service Department at 1-800-DESA LOG
(1-800-337-2564).
You can also visit DESA International’s
technical services web site at
105684
17
VENT-FREE PROPANE/LP PEDESTAL STOVE
ILLUSTRATED
PARTS
BREAKDOWN
S26PT
1
2
10
3
6
7
5
4
9
13
10
8
11
12
14
105684
18
OWNER’S MANUAL
This list contains replaceable parts used in your heater. When ordering parts, follow the
instructions listed under Replacement Parts on page 22 of this manual.
PARTS LIST
S26PT
KEY PART
NO.
NUMBER
DESCRIPTION
QTY.
1
2
3
4
5
6
7
8
106039-01
104286-01
098249-01
105973-01
105737-02
102843-01
099056-28
101329-26
102980-01
099387-09
098271-07
101381-01
098867-10
105972-01
Log Set
ODS Pilot (LP)
ODS Nut
Burner Outlet Tube
Injector Holder
Burner Clip
Burner Orifice Injector
Gas Control Valve
Burner
1
1
2
1
1
1
1
1
1
1
1
1
1
1
9
10
11
12
13
14
Pilot Tube
Ignitor Cable
Piezo Ignitor and Cover
Regulator
Inlet Tube
PARTS AVAILABLE — NOT SHOWN
100563-01
101054-01
Warning Plate
Lighting Instructions Plate
1
1
105684
19
VENT-FREE PROPANE/LP PEDESTAL STOVE
ILLUSTRATED
PARTS
BREAKDOWN
S26PT
1
5
10
18
6
11
8
4
9
17
12
2
16
3
15
7
14
13
105684
20
OWNER’S MANUAL
Thislistcontainsreplaceablepartsusedinyourheater. Whenorderingparts, followtheinstructions
listed under Replacement Parts on page 22 of this manual.
PARTS LIST
S26PT
KEY
NO.
PART NO.
DESCRIPTION
QTY.
1
2
3
4
5
6
7
8
105666-01
105656-01
105655-01
105654-01
105653-01
105657-01
105658-01
105659-01
105660-01
105661-01
105970-01
101382-01
105672-01
105673-01
106754-01
105971-01
099230-02
106020-01
Top Panel, Stove
Pedestal Stove
Stove Base
Stove Back Panel
Louver Panel
Blower Bracket
Door
Firebox Back Panel
Firebox Floor
Firebox Top Assembly
Screen Assembly
Valve Bracket
Brass Trim, Bottom
Brass Trim, Firebox
Knob
Door Hinge
Shoulder Screw
Heat Deflector
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
4
1
9
10
11
12
13
14
15
16
17
18
PARTS AVAILABLE — NOT SHOWN
101054-01
100563-01
104310-10
104108-06
Lighting Instructions Plate
Warning Plate
Information Video
Touch-Up Paint Kit
1
1
1
1
105684
21
VENT-FREE PROPANE/LP PEDESTAL STOVE
CLEANING KIT - CCK
(Not Shown)
REPLACEMENT
PARTS
ACCESSORIES
Purchasetheseheateraccessoriesfromyour
localdealerorPartsCentral(seepage17). If
they cannot supply these accessories call
Your vent-free gas appliance requires regu-
lar cleaning and maintenance to prevent
performance problems. This kit gives you
the tools and instructions to make it easy to
clean all critical areas of your appliance.
Note: Use only original replacement parts.
This will protect your warranty coverage DESA International’s Sales Department at
for parts replaced under warranty.
1-800-458-2472 for referral information.
You can also write to the address listed on
the back page of this manual.
PARTS UNDER WARRANTY
Contact authorized dealers of this product.
If they can’t supply original replacement
part(s)callDESAInternational’sTechnical
Service Department at 1-800-323-5190 for
referral information.
WhencallingDESAInternational,haveready
• your name
• your address
• model and serial numbers of your heater
• how heater was malfunctioning
• type of gas used (propane/LP or natural gas)
• purchase date
EQUIPMENT SHUTOFF
VALVE - GA5010
Equipmentshutoffvalvewith1/8"NPTtap.
Usually, we will ask you to return the defec-
tive part to the factory.
PARTS NOT UNDER
WARRANTY
Contact authorized dealers of this product
or Parts Central (see page 17). If they can’t
supply original replacement part(s) call
DESA International’s Parts Department at
1-800-972-7879 for referral information.
WhencallingDESAInternational,haveready
• model number of your heater
MANUALLY-CONTROLLED
BLOWER KIT - GA3750
• the replacement part number
Provides better heat distribution. Features
variable speed control knob.
105684
22
OWNER’S MANUAL
NOTES
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
105684
23
WARRANTY INFORMATION
KEEP THIS WARRANTY
Model
Serial No.
Date Purchased
Always specify model and serial numbers when communicating with the factory.
Wereservetherighttoamendthesespecificationsatanytimewithoutnotice.Theonlywarrantyapplicableisourstandardwrittenwarranty.
We make no other warranty, expressed or implied.
LIMITED WARRANTY
VENT-FREE PROPANE/LP GAS PEDESTAL STOVE
DESA International warrants this product to be free from defects in materials and components for two (2) years from the date of first
purchase, provided that the product has been properly installed, operated and maintained in accordance with all applicable instructions.
To make a claim under this warranty the Bill of Sale or cancelled check must be presented.
Thiswarrantyisextendedonlytotheoriginalretailpurchaser.Thiswarrantycoversthecostofpart(s)requiredtorestorethisheatertoproper
operating condition and an allowance for labor when provided by a DESA Authorized Service Center. Warranty part(s) MUST be obtained
through authorized dealers of this product and/or DESA International who will provide original factory replacement parts. Failure to use
original factory replacement parts voids this warranty. The heater MUST be installed by a qualified installer in accordance with all local
codes and instructions furnished with the unit.
This warranty does not apply to parts that are not in original condition because of normal wear and tear, or parts that fail or become damaged
as a result of misuse, accidents, lack of proper maintenance or defects caused by improper installation. Travel, diagnostic cost, labor,
transportation and any and all such other costs related to repairing a defective heater will be the responsibility of the owner.
TO THE FULL EXTENT ALLOWED BY THE LAW OF THE JURISDICTION THAT GOVERNS THE SALE OF THE PRODUCT;
THIS EXPRESS WARRANTY EXCLUDES ANY AND ALL OTHER EXPRESSED WARRANTIES AND LIMITS THE DURATION
OF ANY AND ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE TO TWO (2) YEARS ON ALL COMPONENTS FROM THE DATE OF FIRST PURCHASE; AND DESA
INTERNATIONAL’S LIABILITY IS HEREBY LIMITED TO THE PURCHASE PRICE OF THE PRODUCT AND DESA INTERNA-
TIONAL SHALL NOT BE LIABLE FOR ANY OTHER DAMAGES WHATSOEVER INCLUDING INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES.
Some states do not allow a limitation on how long an implied warranty lasts or an exclusion or limitation of incidental or consequential
damages, so the above limitation on implied warranties, or exclusion or limitation on damages may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.
For information about this warranty write:
INTERNATIONAL
2701 Industrial Drive
P.O. Box 90004
Bowling Green, KY 42102-9004
105684 01
105684-01
Rev. C
09/00
NOT A UPC
|